Makita 5092DW Instruction manual

Cordless Circular Saw
85 mm (3-3/8”)MODEL 5 0 9 2 D
85 mm (3-3/8”)MODEL 5 0 9 2 D W
With Fast Charger
INSTRUCTION MANUAL
Uses 12 V / 9.6 V Battery
SPEC IFICAT10NS
Model 5092D
No load speed
(RPM)
Cutting depth
Blade
diameter
I yoI
85 mm
(3-318”)
9ou
I
24.5 mm
15/16”)
Voltaae
v
0
18”
(0--11/16”)
I
Overall
length
1
I
1,000
I
379 mm
(14-15/16”)
weight
I
2.0 kg
(4.4 Ibs)
Model DC1290 Fast Charger
Battery Cartridge 1210
12
~
45”
Output
IrlDUt
I
A C only 5 0 H z
60Hr
1
D C 96V. 12V
Optional: Battery cartridge 9000 (9.6 V )
* Manufacturer reserves the right to change specifications w i t h o u t notice.
Note: Specifications may differ from country t o country.
WARNING: For your personal safety, READ and UNDERSTAND before using.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
I
1
Charsina time
1 Hr
IMPORTANT
SAFETY INSTRUCTIONS
(For All Tools)
WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFETY
PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE
THE RISK OF FIRE, ELECTRIC SHOCK, AND PERSONAL
INJURY, INCLUDING THE FOLLOWING:
READ ALL INSTRUCTIONS.
1. KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries.
2. CONSIDER WORK AREA ENVIRONMENT. Don't use power tools in damp
or w e t locations. Keep work area well lit. Don't expose power tools t o rain.
Don't use tool in presence of flammable liquids or gases.
3. KEEP CHILDREN AWAY. All visitors should be kept away from work area.
Don't let visitors contact tool or extension cord.
4.STORE IDLE TOOLS. When not in use, tools should be stored in dry, and high
or locked-up place - out of reach of children.
5. DON'T FORCE TOOL. It will do the job better and safer at the rate for which
it was intended.
6. USE RIGHT TOOL. Don't force small tool or attachment t o do the job of a
heavy-duty tool. Don't use tool for purpose n o t intended; for example, don't
use circular saw for cutting tree limbs or logs.
7. DRESS PROPERLY. Don't wear loose clothing or jewelry. They can be caught
in moving parts. Rubber gloves and non-skid footwear are recommended
when working outdoors. Wear protective hair covering t o contain long hair.
8.USE SAFETY GLASSES. Also use face or dust mask i f cutting operation is
dusty.
9. DON'T ABUSE CORD. Never carry tool by cord or yank it t o disconnect from
receptacle. Keep cord from heat, oil, and sharp edges.
Use clamps or a vise to hold work. It's safer than using
your hand and it frees both hands t o operate tool.
IO. SECURE WORK.
1 1 . DON'T OVERREACH. Keep proper footing and balance at all times.
12.MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for better and
safer performance. Follow instructions for lubricating and changing accessories. Inspect tool cords periodically and if damaged, have repaired by authorized service facility. Inspect extension cords periodically and replace if
damaged. Keep handles dry, clean, and free from oil and grease.
13. DISCONNECT TOOLS. When n o t in use, before servicing, and when changing accessories, such as blades, bits, cutters.
2
14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking t o
see that keys and adjusting wrenches are removed from tool before turning
it on.
15. AVOID UNINTENTIONAL STARTING. Don't carry tool with finger o n switch.
Be sure switch is OFF when plugging in.
16. OUTDOOR USE EXTENSION CORDS. When tool is used outdoors, use only
extension cords intended for use outdoors and so marked.
17. STAY ALERT. Watch what you are doing, use common sense. Don't
operate
tool when you are tired.
18. CHECK DAMAGED PARTS. Before further use of the tool, a guard or other
part that is damaged should be carefully checked t o determine that it will
operate properly and perform its intended function. Check for alignment of
moving parts, binding of moving parts, breakage of parts, mounting, and any
other conditions that may affect its operation. A guard or other part that
is damaged should be properly repaired or replaced by an authorized service center unless otherwise indicated elsewhere in this instruction manual.
Have defective switches replaced by authorized service center. Don't use
tool if switch does not turn it on and off.
19. GUARD AGAINST ELECTRIC SHOCK. Prevent body contact with grounded
surfaces. For example; pipes, radiators, ranges, refrigerator enclosures.
2 0 . REPLACEMENT PARTS. When servicing, use only identical replacement parts.
21. POLARIZED PLUGS. To reduce the risk of electric shock, this equipment has
a polarized plug (one blade is wider than the other). This plug will f i t i n a
polarized outlet only one way. If the plug does not fit fully i n the outlet,
reverse the plug. If it still does not fit, contact a qualified electrician t o install
the proper outlet. Do not change the plug in any way.
VOLTAGE WARNING: Before connecting the tool t o a power source (receptacle,
outlet, etc.) be sure the voltage supplied is the same as that specified on the
nameplate of the tool. A power source with voltage greater than that specified
for the tool can result in SERIOUS INJURY t o the user - as well as damage t o
the tool. If in doubt, DO NOT PLUG IN THE TOOL. Using a power source with
voltage less than the nameplate rating is harmful t o the motor.
3
IMPORTANT SAFETY INSTRUCTIONS
FOR CHARGER &
BATTERY CARTRIDGE
I. SAVE THESE INSTRUCTIONS - This manual
contains important safety and operating instructions for battery charger.
2.Before using battery charger, read all instructions and cautionary markings
on (1) battery charger, ( 2 ) battery, and (3)product using battery.
3. CAUTION - To reduce risk of injury, charge only MAKITA Battery Cartridge
9000, 9100, 1200 & 1210. Other types of batteries may burst causing
personal injury and damage.
4. Do not expose charger t o rain or snow.
5. Use of an attachment not recommended or sold by the battery charger
manufacturer may result in a risk of fire, electric shock, or injury t o persons.
6. To reduce risk of damage to electric plug and cord, pull by plug rather than
cord when disconnecting charger.
7. Make sure cord is located so that it will not be stepped on, tripped over, or
otherwise subjected t o damage or stress.
8. An extension cord should not be used unless absolutely necessary. Use of
improper extension cord could result in a risk of fire and electric shock. If
extension cord must be used, make sure:
a. That pins on plug of extension cord are the same number, size, and shape
as those of plug on charger;
b. That extension cord is properly wired and in good electrical condition; and
c. That wire size is at least as large as the one specified in the table below.
TABLE 1
RECOMMENDED MINIMUM AWG SIZE FOR
EXTENSION CORDS FOR BATTERY CHARGERS
Length of Cord (Feet)
AWG Size of Cord
25
18
50
18
100
18
150
16
9.Do not operate charger w i t h damaged cord or plug - replace them immediately.
IO. Do not operate charger if it has received a sharp blow, been dropped, or otherwise damaged in any way; take it t o a qualified serviceman.
1 1 . Do not disassemble charger or battery cartridge; take it t o a qualified
serviceman when service or repair is required. Incorrect reassembly may
result in a risk of electric shock or fire.
12.To reduce risk of electric shock, unplug charger f r o m outlet before attempting any maintenance or cleaning. Turning off controls will not reduce this risk.
4
ADDITIONAL SAFETY RULES
FOR CHARGER & BATTERY CARTRIDGE
1. Do not charge Battery Cartridge when temperature is BELOW 10°C (50°F)
or ABOVE 4OoC (104°F).
2. Do not attempt t o use a step-up transformer, an engine generator or DC power
receptacle.
3. Do not allow anything t o cover or clog the charger vents.
4. Always cover the battery terminals with the battery cover when the battery
cartridge is not used.
5. A battery short can ca.use a large current flow, overheating, possible burns
and even a breakdown.
(1) Do not touch the terminals with any conductive material.
(2)Avoid storing battery cartridge in a container with other metal objects such
as nails, coins, etc.
(3)Do not expose battery cartridge t o water or rain.
6. Do not store the tool and Battery Cartridge in locations where the temperature may reach or exceed 35°C (95OF).
7. Do n o t incinerate the Battery Cartridge even if it i s severely damaged or is
completely worn out. The battery cartridge can explode in a fire.
5
ADDITIONAL SAFETY RULES
FOR CORDLESS CIRCULAR SAW
1. Be aware that this tool is always in an operating condition, because it does
not have t o be plugged into an electrical outlet.
2. Wear hearing protection.
3. Keep Guards In Place and In Working Order.
Never wedge or tie lower guard open. Check operation of lower guard before
each use. Don't use if lower guard does not close briskly over saw blade.
CAUTION: If saw is dropped, lower guard may be bent, restricting full return.
4. Do not use blades which are deformed or cracked.
5. Keep Blades Clean and Sharp.
Sharp blades minimize stalling and kickback.
6. DANGER: Keep Hands Away From Cutting Area.
Keep hands away from blades. Don't reach underneath work while blade
is rotating. Don't attempt t o remove cut material when blade is moving.
CAUTION: Blades coast after turn off.
7. Support Large Panels.
Large panels must be supported as shown in Fig. 1 t o minimize the risk of
blade pinching and kickback.
When cutting operation requires the resting of the saw on the work piece,
the saw shall be rested on the larger portion and the smaller piece cut off.
To avoid kickback, do support board
or Dane1 near t h e cut.
I
Don't support board or panel away
from t h e cut.
Fig. 1
Fig.
:
8. Use Rip Fence.
Always use a fence or straight edge guide when ripping.
9. Guard Against Kickback.
Kickback occurs when the saw stalls rapidly and is driven back towards the
operator. Release switch immediately if blade binds or saw stalls. Keep blades
sharp. Support large panels as shown i n Fig. 1. Use fence or straight edge
guide when ripping. Don't force tool. Stay alert exercise control. Don't
remove saw from work during a c u t while the blade is moving.
6
NEVER place your hand or fingers
behind the saw. I f kickback occurs,
the saw could easily jump backwards
over your hand, possibly causing
severe injury.
Fig. 3
IO. Lower
Guard. Raise lower guard w i t h the retracting handle.
11. Adjustments. Before cutting be sure depth and bevel adjustments are tight.
12. Use Only Correct Blades In Mounting. Don’t use blades with incorrect size
holes. Never use defective or incorrect blade washers or bolts.
13. Avoid Cutting Nails. Inspect for and remove all nails from lumber before
cutting.
14. Operate with proper hand support
and proper workpiece support.
I
A typical illustration of proper hand
support and workpiece support.
Fig.
L
WARNING :
It is important t o support the workpiece properly and t o hold the saw firmly
t o prevent loss of control which could cause personal injury. Fig. 4 illustrates
typical hand support of the saw.
7
15. Place the wider portion of the saw base on that part of the workpiece which
is solidly supported, not on the section that will fall off when the cut is made.
As examples, Fig. 5 illustrates the RIGHT way t o cut off the end of a board,
and Fig. 6 the WRONG way. If the workpiece is short or small, clamp it down.
DON'T TRY TO HOLD SHORT PIECES BY HAND!
Fig.
Fig. 6
16. Never attempt t o saw with the circular saw held upside down in a vise.
This is extremely dangerous and can
lead t o serious accidents.
Fig. 7
17. Before setting the tool down after completing a cut, be sure that the lower
(telescoping) guard has closed and the blade has come t o a complete stop.
SAVE THESE INSTRUCTIONS.
8
Installing or removing the battery cartridge
Always switch off the tool before insertion or removal of the battery cartridge.
0
To remove the battery cartridge, pull out
the set plate on the tool and grasp both
sides of the cartridge while withdrawing it
from the tool.
* T o insert the battery cartridge, align the
tongue on the battery cartridge with the
groove in the housing and slip it into
place. Snap the set plate back into place.
Be sure to close the set plate fully before
using the tool.
0
Battery cartridge
Fig. 8
0
Do not use force when inserting the battery cartridge.
I f the cartridge does not slide in easily, it i s not being inserted correctly.
Charging
Your new battery cartridge i s not charged.
You will need to charge it before use. Use
the fast charger Model DCI 290 to charge
the battery cartridge.
0 Plug the fast charger into the proper A/C
voltage source.
0 Insert the battery cartridge so that the
plus and minus terminals on the battery
cartridge are on the same sides as their
respective markings on the fast charger.
Insert the cartridge fully into the port so
that i t rests on the charger port floor.
Charging light
$'
Start b u t t o n Reset b u t t o n
"f
F8g. !
Press the start button (red). The charging light will come on and charging will begin. I f
the charging light does not come on, press the reset button (yellow) first, then the start
button (red). If the charging light goes out within 10 seconds even after pressing the
reset button and s t a r t button a couple of time, the battery cartridge is dead. (CAUTION:
Wait for more than 5 seconds after the charging light goes out to press the reset button
again.) Replace it with a new one.
When the charging light goes out after about one hour, you may remove the fully charged
fast charger.
After charging, unplug the charger from the power source. Refer to the table below for
the charging time.
DC1290
1200 / 1210
Approx
60 mtn
9000
Approx
60 min
9
CAUTION :
.The fast charger Model DC1290 i s specifically designed to charge only Makita battery
cartridges. Never use it for other purposes or for other manufacturer’s batteries.
When you charge a new battery cartridge or a battery cartridge which has not been used
for a long period of time, the charging light may not come on. I f this occurs, just press
the reset button (yellow) first, then the s t a r t button (red) as described before. Charging
wil I begin.
When you charge a new battery cartridge or a battery catridge which has not been used
for a long period of time, it may not accept a full charge. This is a normal condition and
does not indicate a problem. You can recharge the battery cartridge fully after discharging it completely and recharging a couple of times.
0 I f you charge a battery cartridge from a just-operated tool or a battery cartridge which
has been left in a location exposed to direct sunlight or heat for a long time, sometimes
the charging light will not some on. I f this occurs, l e t the cartridge cool off for a while.
Then re-insert it and try to charge it once more.
If you wish to charge two battery cartridges, allow 15 minutes between chargings on the
fast charger.
.Do not keep the button pressed in with tape, etc. or the circuit will not function properly. Also, a malfunction of the charger may result possibly causing overheating, etc.
Removing or installing the saw blade
CAUTION :
Always be sure that the tool is switched off and the battery cartridge i s removed before
installing or removing the blade.
To remove the blade, press the shaft lock
so that the blade cannot revolve and use
the hex wrench to loosen the bolt counterclockwise. Then remove the bolt, outer
flange and blade.
L
10
Fig. 1
To install the blade, follow the removal
procedure in reverse.
BE SURE TO TIGHTEN THE BOLT
SE C U RELY.
Fig. 1 '
CAUTION:
0 Be sure the blade i s installed with teeth pointing up a t the front of the tool.
0
Use only the Makita hex wrench to install or remove the blade.
Hex wrench storage
When not in use, the hex wrench can be
conveniently stored.
Hex wrench
Fig. 1:
11
Adjusting the depth of cut
Loosen the screw on the depth guide and move the base up or down. You can read the
depth of cut by aligning the top of the notch in the depth guide with the graduations on
i t s right side. (Note: This can be done for 0" bevel cutting only.) At the desired depth of
cut, secure the base by tightening the screw.
Top of notch
Base
Screw
Fig. 13
Fig. 14
CAUTION :
Use a shallow depth of cut when cutting thin workpiece for cleaner, safer cuts.
0 After adjusting the depth of cut, always tighten the screw securely.
Bevel cutting
Loosen the screw on the bevel scale plate
on the front of the base. Set for the desired
angle (0"-45") by tilting accordingly, then
the screw securely.
Bevel scale plate
Fig. 15
CAUTION :
After adjusting the depth of cut and bevel cutting angle, be sure to tighten the screw.
12
Sighting
The front of the base is notched to provide
two guide edges.
For straight cuts, align the edge with 0"
engraved on it with your cutting line on
the workpiece.
For 45" bevel cuts, align the edge with 45"
engraved on it with your cutting line.
:
/
For sttaight cuts
c~~~~~~
Top guide
For 45" bevel cuts
line
Fig
Switch action
To prevent the trigger from being accidentally pulled, a lock-off lever i s provided.
To start the tool, slide the lock-off lever
in the direction of the arrow and pull the
trigger. Release the trigger to stop.
Switch ti igger
7,
!\Lock-off
lwei
1
Fig. 1
CAUTION :
Before inserting the battery cartridge into the tool, always check to see that the switch
trigger actuates properly and returns to the "OFF" position when released
Operation
Hold the tool firmly. Set the base plate on
the workpiece to be cut without the blade
making any contact. Then turn the tool on
and wait until the blade attains full speed.
Now simply move the tool forward over
the workpiece surface, keeping i t flat and
advancing smoothly until the sawing i s
completed. To get clean cuts, keep your
sawing line straight and your speed of
advance uniform.
I
i-
.
Base
I
Fig. 1
CAUTION :
.Always gently keep the tool moving straight ahead when cutting. Forcing or twisting the
tool will result in overheating of the motor and dangerous kickback, possibly causing
severe injury.
If the tool is operated continuously until the battery cartridge has discharged, allow the
tool to rest for 15 minutes before proceeding with a fresh battery.
13
Guide rule
The handy guide rule allows you to do
extra-accurate straight cuts. Simply slide
the guide rule up snugly against the side of
the workpiece and secure it in position
with the clamp screw on the front of the
base. It also makes repeated cuts of uniform width possible.
14
Clamp screw
MAINTENANCE
CAUTION :
Always be sure that the tool i s switched off and the battery cartridge i s removed before
attempting or perform inspection or maintenance.
To maintain product SAFETY and RELIABILITY, repairs, maintenance or adjustment
should be performed by Makita Authorized or Factory Service Centers, always using
Makita replacement parts.
15
ACCESSOR I ES
CAUTION :
These accessories or attachments are recommended for use with your Makita tool specified in this
manual. The use of any other accessories or attachments might present a risk of injury t o persons.
The accessories or attachments should be used only in the proper and intended manner.
(12V )
Battery cartridge 9000 (optional)
Part No. 632470-1
(9.6V )
0
Fast charger
Model D C 1 2 9 0
Part No. 113119-108
Fast charger
Model D C 1 2 0 1
Part No. 113126-0
0
Hex wrench
Part No. 783202-0
0
Battery cartridge 1210
Part No. 632277-5
*Guide rule ( R i p fence)
Part No. 164095.8
0
Tungsten carbide tipped
saw blade
For wood
0
Battery cover
Part No. 414938-7
Q
I
Part No, re; ; ; ; D
i
1
Hole(di;x?ter
I
79261 1-2 85 (3-318") 15 (19/32")
721005-A 85 (3-318") 15 (19132")
0
0
Combination saw blade
Fot- rip and cross-cut work.
Has fewer teeth than
cross-cut blade for
faster cutting.
Plywood saw blade
For smooth splinter-free
cutting of p l y w o o d and
other t h i n laminates.
Part No,
No.
teeth
50
721003-8 85 (3-318") 15 (19/32")
Part No,
_____
I
I
D(iam;er
I
I
Hole(;;lli;wter
792299-8 85 (3-318") 15 (19/32")
16
20
24
Hole diameter
(mm)
Diameter
(mm)
No.
teeth
1
I
No.
teeth
50
Sei,
19-'95
US
85 mm (3-3/8")
CORDLESS CIRCULAR SAW
Model 5092D
Note: The switch and other part configurations
may differ from country to country.
17
sev-19-
MODEL 5 0 9 2 D
IFOM,,I:,DESCRIPTION
ILLM
AtD
DESCRIPTION
MACHINE
~
1
1
26
2
3
1
1
1
1
1
27
28
29
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
14
1
1
1
1
6
1
1
1
1
1
1
1
20
1
21
1
22
21
24
25
18
2
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
41
48
49
50
1
1
3
1
1
1
1
1
1
1
1
1
1
1
1
3
1
1
1
1
1
1
1
1
1
Slop Ring E 4
i e x Nu1 M 5
rapping screw d X i 8
3all Bearing 6000LLB
Narning Card
:ampresslo" s p m g 3
s x h Off Lever
JC Motor 12 V
Wofor Housing
uame Plate
i n u s m y SPI IWith them 131
Swch
set Pldfe
B a i i e r y Holder
S W , t C h Lever
Tapping Screw 4 x 1 8
S c r e w M5x10
Spring Washer 5
F l a l Washer 5
Base
S ~ m wM 5 x 1 0
S p r ~ n yPin 4 4 0
Flat Wahtier 5
sprinq Wdahcr 5
S c r ~ wM5x10
95
us
Recycling the Battery
The only way to dispose of a Makita battery is
to recycle it. The law prohibits any other
method of disposal.
1
Ni-Cd
To recycle the battery:
1. Remove the battery from the tool.
2. a). Take the battery to your nearest Makita Factory Service Center
or
b). Take the battery to your nearest Makita Authorized Service Center or
Distributor that has been designated as a Makita battery recycling location.
Call your nearest Makita Service Center or Distributor to determine the location
that provides Makita battery recycling. See your local Yellow Pages under
”Tools-Electric’:
MAKITA LIMITED ONE YEAR WARRANTY
Warranty Policy
Every Makita tool IS thoroughly inspected and tested before leaving the factory. It is warranted t o
be free of defects from workmanship and materials for the period of ONE YEAR from the date of
original purchase. Should any trouble develop during this one-year period, return the COMPLETE
tool, freight prepaid, t o one of Makita’s Factory or Authorized Service Centers. If inspection shows
the trouble Is caused by defective workmanship or material, Makita will repair (or at our option,
replace) without charge.
This Warranty does not apply where:
repairs have been made or attempted by others:
repairs are required because of normal wem and tear:
The tool has been abused, misused or improperly maintained;
alterations have been made t o the tool.
IN NO EVENT SHALL MAKITA BE LIABLE FOR ANY INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES FROM THE SALE OR USE OF THE PRODUCT. THIS DISCLAIMER
APPLIES BOTH DURING AND AFTER THE TERM OF THIS WARRANTY.
MAKITA DISCLAIMS LIABILITY FOR ANY IMPLIED WARRANTIES, INCLUDING IMPLIED
WARRANTIES O F “MERCHANTABILITY” AND “FITNESS FOR A SPECIFIC PURPOSE,”
AFTER THE ONE-YEAR TERM O F THIS WARRANTY.
This Warranty aves you specific legal rights, and you may also have other rights which vary from
state to state. Some states do not allow the exclusion or limitation of incidental or consequential
damages, so the above limitation or exclusion may not apply to you. Some states do not allow
limitation on how long an implied warranty lasts, so the above limitation may not apply t o you.
Makita Corporation of America
2650 Gainesville Hwy., Buford, GA 30518
884050 - 063
PRINTED IN USA
1995 - 11 - C
1