EdgeStar BWC120SSLT Beverage Refrigerator Owner`s manual

Beverage Cooler
BWC120SSLT
Owner’s Manual
For more information on other great EdgeStar products on the web, go to http://www.edgestar.com
Important Safety Information
Improper handling can cause serious damage to the EdgeStar beverage cooler and/or injury to the user. This beverage
cooler is designed for domestic indoor use only. Do not use the unit for industrial or commercial use. Any other use
may invalidate the warranty. Please review the ratings label located on the rear panel of the unit for electrical and other
technical data related to this unit. The unit must be used in a properly grounded wall outlet.
Please read and follow the safety information listed below to reduce the risk of fire, electric shock or injury.
Electrical Safety
• Do not exceed the power outlet ratings.
• It is recommended the beverage cooler be
connected on its own circuit.
• The unit must be installed in accordance with
state and local electrical codes.
• A standard electrical supply (115 V, 60Hz), that is
properly grounded in accordance with the
National Electrical Code and local codes and
ordinances is required.
• Use outlets that cannot be turned off by a switch
or pull chain.
• Always turn the unit off and unplug it from the
outlet when cleaning.
• Unplug the unit if it is not going to be used for an
extended period of time.
• Do not operate the unit with a power plug missing
the ground plug, a damaged cord or a loose
socket.
• Be sure the beverage cooler is properly
grounded.
• Never plug or unplug the unit with wet hands.
• Do not bypass, cut or remove the grounding plug.
• Do not use extension cords or power strips with
this unit. You may need to contact your electrician
if it is necessary to use a longer cord or if you do
not have a grounded outlet. Do not modify the
power cord’s length or share the outlet with other
appliances.
• Do not start or stop the unit by switching the
circuit’s power on and off.
• If the power cord is damaged, it must be replaced
by the manufacturer or a qualified technician.
• Never repair the unit while it is plugged in.
• Immediately unplug the unit if it makes strange
sounds, emits smells or smoke comes out of it,
and contact customer service.
• Do not remove any part of the casing unless
instructed by an authorized technician.
• You should never attempt to repair the unit
yourself.
• Contact customer service for service options if the
unit needs service.
i
General Safety
• To prevent back and other types of injuries, use at
least two people to move and install the beverage
cooler.
• This unit is not intended for use by persons,
including children, with reduced physical, sensory or
mental capabilities, unless they have been given
supervision or instruction concerning the use of the
appliance by the person(s) responsible for their
safety.
• Install the cooler in a well ventilated area where the
ambient temperature is above 50°F and below 95°F.
• The temperature range for this cooler is optimized
for beverage storage. Perishable food items may
require a different storage environment.
• Do not place hot or warm items into the cooler
before they cool down to room temperature.
• This unit is designed to be installed indoors, and
protected from rain, sleet, snow, and/or moisture.
• This unit is not intended to be used by children.
• Children should be supervised to ensure that they
do not play with this product.
• Never allow children to crawl inside the beverage
cooler. If disposing the unit, remove the door.
• Do not use this cooler near flammable gas or
combustibles, such as gasoline, benzene, thinner,
etc.
• Do not place the unit near heat sources such as
ovens, grills, or direct sunlight.
• Only use in an upright position on a flat, level
surface and provide proper ventilation.
• Do not pinch or kink the power supply line between
the unit and cabinet.
• Do not leave any cleaning solutions in the unit
• Do not use solvent-based cleaning agents or
abrasive solutions to clean the unit as they may
damage the interior and exterior.
• Do not place any other appliances or allow anyone
to sit on top of the unit.
• Do not turn the unit upside down, on its side, or at
an angle off level.
• Do not move the unit without emptying the contents
and securing the door in a closed position.
Table of Contents
IMPORTANT SAFETY INFORMATION ................................................................. I INTRODUCTION ................................................................................................... 1 PARTS IDENTIFICATION ..................................................................................... 2 BACK VIEW .......................................................................................................... 2 FRONT VIEW ........................................................................................................ 2 INSTALLING THE BEVERAGE COOLER ........................................................... 3 TYPE OF INSTALLATION ........................................................................................ 3 Free-standing installation: ............................................................................. 3 INSTALLATION CLEARANCE REQUIREMENTS .......................................................... 3 ELECTRICAL REQUIREMENTS ................................................................................ 4 Recommended grounding method ................................................................ 4 LEVELING THE BEVERAGE COOLER ....................................................................... 4 REVERSING THE DOOR SWING.............................................................................. 5 OPERATION .......................................................................................................... 5 INSTALLATION CHECK LIST BEFORE OPERATION .................................................... 5 ADJUSTING THE TEMPERATURE ............................................................................ 5 NORMAL SOUNDS ................................................................................................ 6 DEFROSTING ....................................................................................................... 6 PREPARING THE BEVERAGE COOLER FOR STORAGE.............................................. 6 CLEANING AND MAINTENANCE ........................................................................ 7 EXTERIOR CLEANING ........................................................................................... 7 INTERIOR CLEANING ............................................................................................. 7 TROUBLESHOOTING .......................................................................................... 7 TROUBLESHOOTING CONTINUED ........................................................................... 8 SPECIFICATIONS ................................................................................................. 9 EDGESTAR LIMITED WARRANTY ................................................................... 10 First Time Operating Instructions
Before use, make sure all packaging labels and materials are all removed from
the unit. Be sure to keep track of all included parts and pieces before discarding
packaging materials. It is advised that you keep the original box and packaging
materials in case you are ever to move or ship the appliance in the future.
Let the unit stand for at least 24 hours before you use it; this allows the cooling
components time to settle from transit. The instruction manual should be read
before use.
This owner’s manual is provided for reference use only. Specifications may
change without prior notice. Refer to the product label on the back of your
beverage cooler for the latest technical information.
EdgeStar Beverage Cooler
ii
Introduction
Thank you for purchasing this EdgeStar beverage cooler. We are glad you chose
us. We believe that your purchase of this product opens a relationship between
you and EdgeStar. We will provide the customer support needed to nurture that
relationship.
This manual contains important information regarding the proper installation, use
and maintenance of your beverage cooler. Following this manual will ensure that
your product will work at its peak performance and efficiency.
Please save the original product packaging in case you need to safely transport
your beverage cooler.
For Your Records:
Please write down the model number and serial number
below for future reference. Both numbers are located on the
ratings label on the back of your unit and are needed to
obtain warranty service. You may also want to staple your
receipt to this manual as it is the proof of your purchase, and
is also needed for service under your warranty.
Model Number:
Serial Number:
Date of Purchase:
To better serve you, please do the following before contacting customer service:
1
•
If you received a damaged product, immediately contact the retailer or
dealer that sold you the product.
•
Read and follow this instruction manual carefully to help you install, use
and maintain your beverage cooler.
•
Read the troubleshooting section of this manual as it will help you
diagnose and solve common issues.
•
Visit us on the web at http://www.edgestar.com to register your
product, download product guides, additional troubleshooting resources
and up-to-date information.
•
If you need warranty service, our friendly customer service
representatives are available via email at [email protected] or by
telephone at 1 (866) 319-5473.
Parts Identification
Top Right Hinge
Front View
Shelf
Stainless Steel Door
Lock
Leveling foot
Back View
Product Label
Tip: Gather the model
and serial number
from the product label
and write them down
before installing the
beverage cooler.
Power Cord
Cabinet
EdgeStar Beverage Cooler
Power Plug
2
Installing the Beverage Cooler
The beverage cooler should be installed in accordance with local
electrical code requirements. The beverage cooler should also be placed
in a location that is strong enough to support its total weight, keeping in
mind that it will weigh substantially more when fully loaded than when
empty.
Before you plug the beverage cooler into a power supply, be sure to let it
stand upright for at least 24 hours to allow the compressor’s oils to settle.
Unpacking the Beverage Cooler
WARNING: You may need to use two more people to move and install the
beverage cooler. Failure to do so can result in back or other injury.
Carefully remove the packaging materials. Remove any shipping tape and
glue from your beverage cooler before using. Do not use sharp
instruments, rubbing alcohol, flammable fluids, or abrasive cleaners to
remove tape or glue. These products can damage the surface of your
beverage cooler.
IMPORTANT: Do not remove any safety, warning, or product information
labels from your beverage cooler.
Type of Installation
This beverage cooler has been designed for free-standing installation
only. There must be adequate ventilation space around the top, back and
sides of the unit.
Important Notes:
• Choose a location that has
ambient temperatures above
50°F and below 95°F.
Operation outside these
temperatures may result in
lowered efficiency or cause
other adverse effects.
• This unit MUST be installed
in an area protected from the
elements, e.g., wind, rain,
water spray or drips.
• The beverage cooler should
not be located next to ovens,
grills or other high heat
sources.
3
Free-standing installation:
A free-standing installation will allow you to install the beverage cooler in
almost any place you desire. You must follow the stated instructions for
electrical requirements, installation clearance, and leveling the beverage
cooler.
WARNING: Do NOT install the beverage cooler built-in or behind a
closed cabinet door.
Installation Clearance Requirements
• To ensure proper ventilation, allow at least 10” clearance at the back, 5”
at top and 5” at sides.
• The beverage cooler should be installed on a firm and level surface that
will be able to support the entire weight of a fully loaded unit. It is
important for the beverage cooler to be level in order to work properly. If
needed, you can adjust the height of the beverage cooler by rotating the
feet. See the “Leveling the Beverage cooler” section.
• A standard electrical supply (115 VAC only, 60 Hz), properly grounded
in accordance with National Electrical Code and local codes and
ordinances is required.
Electrical Requirements
•
•
•
•
•
ELECTRIC SHOCK HAZARD!
Plug into a grounded 3-prong outlet.
Never remove the grounding prong from the plug.
Never use an adapter to bypass the grounding prong.
DO NOT use an extension cord.
Failure to follow these instructions can result in fire,
electrical shock, or death.
Before you move your beverage cooler into its final location, it is
important to make sure you have the proper electrical connection:
A standard electrical supply (115 V, 60Hz), properly grounded in
accordance with the National Electrical Code and local codes and
ordinances, is required.
It is recommended that a separate circuit, serving only your beverage
cooler, be provided. Use receptacles that cannot be turned off by a switch
or pull chain.
The fuse (or circuit breaker) size should be 3 Amps.
Recommended grounding method
For your personal safety, this appliance must be grounded. It is equipped
with a power supply cord having a 3-prong grounding plug. To minimize
possible shock hazard, the cord must be plugged into a mating 3-pronged
wall socket, and grounded in accordance with the National Electrical
Code and local codes and ordinances. If a mating wall socket is not
available, it is the personal responsibility of the customer to have a
properly grounded, 3-prong wall receptacle installed by a qualified
electrician.
Leveling the Beverage Cooler
It is important for the beverage cooler to be leveled in order to work
properly. It can be raised or lowered by rotating the plastic sheaths
around each of the feet on the bottom of the machine. If you find that the
surface is not level, rotate the feet until the beverage cooler becomes
level .You may need to make several adjustments to level it. We
recommend using a carpenter’s level to check the machine.
1. Place a carpenter’s level on top of the product to see if the beverage
cooler is level from front to back and side to side.
2. Adjust the height of the feet as follows:
Turn the leveling feet to the right to lower that side of the refrigerator.
Turn the leveling feet to the left to raise that side of the refrigerator.
IMPORTANT: Once you are ready to install it in a cabinet or directly on
the floor, you must adjust the feet to level the beverage cooler.
EdgeStar Beverage Cooler
4
Reversing the Door Swing
Hinge Cover
Screws
Top hinge
Cabinet
Door
Tools needed: flathead screwdriver, Phillips screwdriver
IMPORTANT: Before you begin, unplug the beverage cooler from
power.
To remove the door:
1. Using a flathead screw driver carefully pry the top hinge cover
off.
2. Using a Phillips screwdriver, remove the screws and take off top
hinge. Keep the parts together and set them aside.
3. Lift the door off the bottom hinge and set the door aside.
4. Remove the bottom hinge by removing the screws with a Phillips
head screwdriver.
To install the door:
1. Using a flathead screwdriver, remove the decorative plugs or
cover from the opposite cabinet top corner and from the door. Set
aside.
2. Install the bottom hinge at the opposite side corner and fasten
the screws.
3. Position the door on the bottom hinge.
4. Align the door on the bottom hinge and install the top hinge.
5. Push the decorative plugs and covers into the corresponding
holes.
OPERATION
Installation Check List before Operation
1. Have all packing materials and tape been removed from the
interior and exterior of the beverage cooler?
2. Have the installation instructions been followed, including
connecting the machine to electricity? And has proper grounding
been installed for the beverage cooler?
3. Has the machine been leveled?
4. Is the beverage cooler in a site where the ambient temperature is
between 50º F and 95º F all year round?
5. Is there a clearance of at least 10” at the rear, 5” at the top and
5” at the sides for proper air circulation?
Adjusting the Temperature
Caution: If you powered off
the unit, please wait at least
5 minutes before powering it
back on.
5
The temperature in the beverage cooler is controlled by the
thermostat control knob located inside the unit. Turn the thermostat
control knob to regulate the temperature inside the cooler. The
knob has markings to indicate the relative temperature settings.
The higher number relates to the colder relative temperature. Allow
at least 24 hours before storing your beverages and to allow the
temperature to acclimate.
Normal Sounds
Your new beverage cooler may make sounds that are not familiar to
you. Most of the new sounds are normal. Hard surfaces like the
floor, walls can make the sounds seem louder than they actually
are. The following describes the kinds of sounds that might be new
to you and what may be making them.
• Rattling noises may come from the flow of the refrigerant or the
water line, Items stored on top of the beverage cooler can also
make noises.
• The high efficiency compressor may make a pulsating or highpitched sound.
• Water running from the evaporator to the water bin may make a
splashing sound.
• As each cycle ends, you may hear a gurgling sound due to the
refrigerant flowing in your beverage cooler.
• You may hear air being forced over the condenser by the
condenser fan.
Defrosting
This beverage cooler does NOT have an automatic defrost feature.
Therefore, in a colder environment and settings, frost may build up
frequently. Additionally, the more humid the ambient conditions, the
more frost may build up. Keep the door closed as much as possible
and avoid opening the door unnecessarily to minimize frost buildup.
If frost is preventing the door from closing properly, you may need
to power the unit off until the frost melts. Use a soft absorbent towel
to dry the unit.
WARNING: Never attempt to remove frost with a sharp object!
Preparing the Beverage Cooler for Storage
If the beverage cooler will not be used for a long time, or is to be
moved to another place, it will be necessary to defrost the unit and
dry the interior.
IMPORTANT:
1. Disconnect the cooler from the power supply by removing the
power plug from the wall socket.
2. Leave the door open to allow for air circulation and to prevent
mold, mildew and unpleasant smells.
• Do not touch the power plug
when your hands are wet.
• Never unplug the unit by
pulling on the plug.
CAUTION: Store the unit out of the reach of children. If you have
children, you may want to take additional precautions such as
removing the door to prevent a child from being trapped inside the
cooler!
EdgeStar Beverage Cooler
6
CLEANING AND MAINTENANCE
Periodic cleaning and proper maintenance will ensure efficiency, top
performance, and long life.
Exterior Cleaning
The door and cabinet may be cleaned with a mild detergent and
lukewarm water solution such as 2 tablespoons of baking soda to 1 quart
of water.
Do not use solvent based or abrasive cleaners. Use a soft sponge and
rinse with clean water. Wipe with a soft clean towel to prevent water
spotting. If the door panel is stainless steel, it can discolor when exposed
to chlorine gas and moisture. Clean stainless steel with a cloth dampened
with a mild detergent and warm water solution. Never use an abrasive or
caustic cleaning agent.
Interior Cleaning
The beverage cooler’s interior should be cleaned occasionally.
1. Disconnect power to the unit.
2. Open the door and remove the contents and shelves.
3. Wait until the unit defrosts.
4. With a clean cloth, wipe down the interior of the unit.
5. Reinsert the shelves and beverages.
6. Reconnect power to the unit.
TROUBLESHOOTING
Before Calling for Help
If the unit appears to be malfunctioning, read through the OPERATION
section of this manual first. If the problem persists, check the
Troubleshooting Guide below and on the following page. The problem
could be something that can easily be solved or explained.
Symptoms
The beverage cooler
turns on and off
frequently.
7
Possible causes
Solutions
The room temperature is
higher than the
recommended ambient
environment.
Run the cooler at the appropriate ambient temperature.
The door is being opened
often.
Minimize the number of times the door is opened.
The door is not completely
closed.
Make sure the door is completely closed.
The door gasket is not
sealing properly.
Make sure the door gasket is properly sealing.
The cooler does not have the
suggested ventilation.
Read and follow the “Installation Clearance
Requirements” section.
Troubleshooting continued
Issue
The beverage cooler
does not turn on.
The beverage cooler will
not reach the desired
temperature
Possible cause
Solution
There is a power failure.
Ensure the cooler is plugged in and the power outlet has
power.
The cooler is not plugged in.
Plug the unit in to a power outlet that has sufficient
amperage.
A house fuse has blown or
the circuit breaker is tripped.
Replace the broken fuse in your fuse box or reset the
breaker.
The cooler is placed too
close to a heat source.
Keep the cooler away from direct sun light or other heat
sources.
The cooler does not have
sufficient ventilation.
Read and follow the “Installation Clearance Requirements”
section.
The door is opened too
frequently or for a long
period of time.
Close the door tightly and do not open the door too
frequently or for a long period of time.
Certain sounds are normal.
Read the “Normal Sounds” section.
The unit is not level or is
touching another appliance.
Check to make sure that the cooler is level, and that it is
not in contact with another appliance or furniture.
The unit is not grounded
properly.
Contact your local electrician to test your electrical
grounding system.
The beverage cooler is
making strange noises
The body of the beverage
cooler is electrified.
The environment is humid or
the ambient temperature is
too low.
Frost is forming in the
beverage cooler.
The door gasket is not
installed properly.
The door is being opened
too frequently.
Your cooler is not level.
The door gasket is dirty.
The door will not shut
properly.
Manual defrosting is required; unplug the unit to allow the
frost to melt. If frost builds up frequently, you can move
the unit to a location with a warmer temperature, minimize
the number of times you open the door, or check the door
gasket for a good seal.
Make sure the cooler is on a level surface.
Clean the door gasket.
The door gasket is not
installed correctly.
Make sure the door gasket is properly installed.
The shelves are incorrectly
installed.
Correctly install the shelves.
EdgeStar Beverage Cooler
8
Specifications
Description of product
Freestanding Beverage Cooler
Model
BWC120SSLT
Voltage/Frequency
AC 115V~60Hz
Amperage
1.3 Amps
Input Power
85 Watts
Color
Black Cabinet; Stainless Steel
Door
Storage Capacity
118 Cans*
Temperature Range
Low 30s - Mid 50sºF
Dimensions
(Height x Width x Depth )
33" x 19" x 18 1/4"
Weight
64 pounds
Note: Technical data and performance information is provided for
reference only.
Specifications are subject to change. Check the rating label on the
beverage cooler for the most accurate information.
*Note on beverage storage capacity:
The beverage cooler can store 118 standard 12 oz. cans.
9
EdgeStar Limited Warranty
One (1) Year Parts & Ninety (90) Days Labor
This product is warranted by EdgeStar to be free from defective workmanship and materials, subject to any conditions
set forth as follows:
WHAT IS COVERED:
LABOR: For a period of NINETY (90) DAYS from the date of original purchase, labor will be performed free of charge at
an authorized EdgeStar repair facility. At its option, EdgeStar will repair the product with new or remanufactured parts,
or exchange the defective product with a new, refurbished, or remanufactured product. If a product is replaced, it will
carry the remaining warranty of the original product. After the ninety (90) day period, EdgeStar will no longer be
responsible for labor charges incurred. All defective products and parts covered by this warranty will be repaired or
replaced on a mail-in basis to an EdgeStar authorized repair facility.
PARTS: For a period of ONE (1) YEAR from the date of original purchase, EdgeStar will supply new, rebuilt, or
refurbished parts free of charge. EdgeStar may request a defective part be returned in exchange for the replacement
part. All replacement parts or products will be new, remanufactured, or refurbished. All products and parts replaced by
EdgeStar under warranty service become the property of EdgeStar.
This warranty applies to the original purchaser only, and only covers defects in workmanship experienced during
operation of the product under normal service, maintenance, and usage conditions. This warranty applies to the
purchase and use of this product in residential settings within the United States of America.
WHAT IS NOT COVERED:
The following limitations apply to the coverage of this warranty. This warranty does not cover:
•
Labor charges for installation, setup or training to use the product.
•
Shipping damage, and any damage caused by improper packaging for shipment to an authorized service center, and any
damaged caused by improper voltage or any other misuse, including abnormal service, handling, or usage.
•
Cosmetic damage such as scratches and dents.
•
Normal wear and tear on parts or replacement of parts designed to be replaced, e.g. filters, cartridges, batteries.
•
Service trips to deliver, pick-up, or repair, install the product, or to instruct in proper usage of the product.
•
Damages or operating problems resulting from misuse, abuse, operation outside environmental specifications, uses
contrary to instructions provided in the owner’s manual, accidents, acts of God, vermin, fire, flood, improper installation,
unauthorized service, maintenance negligence, unauthorized installation or modification, or commercial use.
•
Labor charges incurred 91 days or more after the date of original purchase.
•
The use of EdgeStar products in commercial settings.
•
Optional accessories, attachments, and appearance items.
•
Products that have been modified to perform outside of specifications without the prior written permission of EdgeStar.
•
Products lost in shipment, or theft.
•
Products sold AS IS or from an unauthorized reseller.
•
Products that have had their serial numbers removed or defaced. Products with serial numbers that have been invalidated.
OBTAINING WARRANTY SERVICE:
If you believe your product is defective, contact EdgeStar Customer Support for troubleshooting assistance and
warranty service at 1-866-319-5473. Please have your serial number and proof of purchase available. Once an
EdgeStar authorized representative has confirmed that your product is defective and eligible for warranty service, the
product must be returned to an EdgeStar repair facility. The purchaser is solely responsible for prepaying all shipping
related costs to and from the repair facility. EdgeStar is not responsible for damage resulting from shipper mishandling
or improper packaging. Do not return a defective product to the place of purchase. Products received without a return
authorization number will be refused.
THIS WARRANTY IS IN LIEU OF ANY OTHER WARRANTY, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, ANY
WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. TO THE EXTENT ANY IMPLIED
WARRANTY IS REQUIRED BY LAW, IT IS LIMITED IN DURATION TO THE EXPRESS WARRANTY PERIOD ABOVE. NEITHER
THE MANUFACTURER NOR ITS DISTRIBUTORS SHALL BE LIABLE FOR ANY INCIDENTAL, CONSEQUENTIAL, INDIRECT,
SPECIAL, OR PUNITIVE DAMAGES OF ANY NATURE, INCLUDING WITHOUT LIMITATION, LOST REVENUES OR PROFITS,
OR ANY OTHER DAMAGE WHETHER BASED IN CONTRACT, TORT, OR OTHERWISE. SOME STATES DO NOT ALLOW THE
EXCLUSION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE EXCLUSION MAY NOT APPLY TO YOU.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY HAVE OTHER RIGHTS THAT VARY FROM STATE TO
STATE.
EdgeStar Beverage Cooler
10
EdgeStar Products
500 N. Capital of TX Hwy, Bldg 5
Austin, TX 78746
Toll Free: 1-866-319-5473
Web: http://www.edgestar.com
E-mail: [email protected]
Register your product, download owner’s manuals, access additional
troubleshooting resources, and obtain more information on other
great EdgeStar products on the web at: http://www.edgestar.com
Product contents and specifications may change without notice.
Copyright © 2011 Living Direct, Inc. All rights reserved.