Bosch WZ20NXV550-0 Installation manual

Integrated IR Bullet Camera
WZ20
en
Installation Manual
Integrated IR Bullet Camera
Table of Contents | en
3
Table of Contents
1
Safety
4
1.1
Safety Precautions
4
1.2
Important Safety Instructions
4
1.3
Important Notices
6
1.4
FCC & ICES compliance
9
1.5
Warranty / Limitation of Liability
11
1.6
Contact Information
13
2
Introduction
14
2.1
Description
14
2.2
Parts List
14
3
Installation
15
4
Configuration
16
4.1
Configuration Overview
16
4.1.1
Adjusting Pan, Tilt, Rotate
17
4.1.2
Adjusting Focus
17
4.1.3
Adjusting Zoom
18
5
On-Screen Menu
19
5.1
OSD Menu
19
5.1.1
Exposure Submenu
19
5.1.2
Color Submenu
20
5.1.3
Day/Night Submenu
21
5.1.4
Function Submenu
21
5.1.5
Motion Submenu
22
5.1.6
Privacy Submenu
23
5.1.7
Setup Submenu
24
5.1.8
Exit Submenu
25
6
Troubleshooting
26
6.1
Troubleshooting Tips
26
7
Technical Specifications
27
Bosch Security Systems, Inc.
Installation Manual
| 2.0 | 2011.06
4
en | Safety
Integrated IR Bullet Camera
1
Safety
1.1
Safety Precautions
DANGER!
High risk: This symbol indicates an imminently hazardous
situation such as “Dangerous Voltage” inside the product.
If not avoided, this will result in an electrical shock, serious
bodily injury, or death.
WARNING!
Medium risk: Indicates a potentially hazardous situation.
If not avoided, this could result in minor or moderate bodily
injury.
CAUTION!
Low risk: Indicates a potentially hazardous situation.
If not avoided, this could result in property damage or risk of
damage to the unit.
1.2
Important Safety Instructions
Read, follow, and retain all of the following safety instructions.
Heed all warnings on the unit and in the operating instructions
before operating the unit.
CAUTION!
In USA and Canada, use Class 2 power supply only.
CAUTION!
These servicing instructions are for use by qualified service
personnel only. To reduce the risk of electric shock do not
perform any servicing other than that contained in the
operating instructions unless you are qualified to do so.
1.
| 2.0 | 2011.06
Read these instructions.
Installation Manual
Bosch Security Systems, Inc.
Integrated IR Bullet Camera
2.
Safety | en
Keep this instruction.
3.
Heed all warnings.
4.
Follow all instructions.
5.
Do not use this apparatus near water.
6.
Clean inside only with dry cloth.
7.
5
Do not block any ventilation openings. Install in
accordance with manufacturer’s instructions.
8.
Do not install near any heat sources such as radiators, heat
registers, stoves or other apparatus (including amplifiers)
that produce heat.
9.
Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades with
one wider than the other. A grounding type plug has two
blades and a third grounding prong. The wide blade or the
third prong is provided for your safety. If the provided plug
does not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched
particularly at plugs, convenience receptacles, and the
power where they exit from the apparatus.
11. Use only attachments/accessories specified by the
manufacturer.
12. Unplug this apparatus during lightning storms or when
unused for long periods of time.
13. Refer all servicing to qualified service personnel. Servicing
is required when the apparatus has been damaged in any
way, such as power-supply cord or plug is damaged, liquid
has been spilled or objects have fallen into the apparatus,
the apparatus has been exposed to rain or moisture, does
not operate normally, or has been dropped.
Bosch Security Systems, Inc.
Installation Manual
| 2.0 | 2011.06
6
en | Safety
1.3
Integrated IR Bullet Camera
Important Notices
Accessories - Do not place this unit on an unstable stand,
tripod, bracket, or mount. The unit may fall, causing serious
injury and/or serious damage to the unit. Use only with the
cart, stand, tripod, bracket, or table specified by the
manufacturer. When a cart is used, use caution and care when
moving the cart/apparatus combination to avoid injury from
tip-over. Quick stops, excessive force, or uneven surfaces may
cause the cart/unit combination to overturn. Mount the unit
per the manufacturer's instructions.
All-pole power switch - Incorporate an all-pole power switch,
with a contact separation of at least 3 mm in each pole, into the
electrical installation of the building. If it is needed to open the
housing for servicing and/or other activities, use this all-pole
switch as the main disconnect device for switching off the
voltage to the unit.
Camera grounding - For mounting the camera in potentially
damp environments, ensure to ground the system using the
ground connection of the power supply connector (see section:
Connecting external power supply).
Camera signal - Protect the cable with a primary protector if
the camera signal is beyond 140 feet, in accordance with
NEC800 (CEC Section 60).
Coax grounding:
–
Ground the cable system if connecting an outside cable
system to the unit.
–
Connect outdoor equipment to the unit's inputs only after
this unit has had its grounding plug connected to a
grounded outlet or its ground terminal is properly
connected to a ground source.
–
Disconnect the unit's input connectors from outdoor
equipment before disconnecting the grounding plug or
grounding terminal.
–
Follow proper safety precautions such as grounding for
any outdoor device connected to this unit.
| 2.0 | 2011.06
Installation Manual
Bosch Security Systems, Inc.
Integrated IR Bullet Camera
Safety | en
7
U.S.A. models only - Section 810 of the National Electrical Code,
ANSI/NFPA No.70, provides information regarding proper
grounding of the mount and supporting structure, grounding of
the coax to a discharge unit, size of grounding conductors,
location of discharge unit, connection to grounding electrodes,
and requirements for the grounding electrode.
Disposal - Your Bosch product was developed and
manufactured with high-quality material and components that
can be recycled and reused. This symbol means that electronic
and electrical appliances, which have reached the end of their
working life, must be collected and disposed of separately
from household waste material. Separate collecting systems
are usually in place for disused electronic and electrical
products. Please dispose of these units at an environmentally
compatible recycling facility, per European Directive 2002/96/
EC.
Electronic Surveillance - This device is intended for use in
public areas only. U.S. federal law strictly prohibits
surreptitious recording of oral communications.
Environmental statement - Bosch has a strong commitment
towards the environment. This unit has been designed to
respect the environment as much as possible.
Electrostatic-sensitive device - Use proper CMOS/MOS-FET
handling precautions to avoid electrostatic discharge.
NOTE: Wear required grounded wrist straps and observe proper
ESD safety precautions when handling the electrostaticsensitive printed circuit boards.
Fuse rating - For protection of the device, the branch circuit
protection must be secured with a maximum fuse rating of 16A.
This must be in accordance with NEC800 (CEC Section 60).
Outdoor signals - The installation for outdoor signals, especially
regarding clearance from power and lightning conductors and
transient protection, must be in accordance with NEC725 and
NEC800 (CEC Rule 16-224 and CEC Section 60).
Permanently connected equipment - Incorporate a readily
accessible disconnect device external to the equipment.
Bosch Security Systems, Inc.
Installation Manual
| 2.0 | 2011.06
8
en | Safety
Integrated IR Bullet Camera
Pluggable equipment - Install the socket outlet near the
equipment so it is easily accessible.
Power resupply - If the unit is forced to power down due to
exceeding the specified operating temperatures, disconnect
the power cord, wait for at least 30 seconds, and then
reconnect the power cord.
Power lines - Do not locate the camera near overhead power
lines, power circuits, or electrical lights, nor where it may
contact such power lines, circuits, or lights.
SELV - All the input/output ports are Safety Extra Low Voltage
(SELV) circuits. SELV circuits should only be connected to
other SELV circuits.
Because the ISDN circuits are treated like telephone-network
voltage, avoid connecting the SELV circuit to the Telephone
Network Voltage (TNV) circuits.
System ground/Safety ground
System (video) ground is indicated by the symbol
.
The system ground is only used to comply with safety standards
or installation practices in certain countries. Bosch does not
recommend connecting system ground to safety ground unless
it is explicitly required. However, if the system ground and
safety ground are connected and grounding loops are causing
interference in the video signal, use an isolation transformer
(available separately from Bosch).
CAUTION!
Connecting System ground to Safety ground may result in
ground loops that can disrupt the CCTV system.
Video loss - Video loss is inherent to digital video recording;
therefore, Bosch Security Systems cannot be held liable for any
damage that results from missing video information. To
minimize the risk of lost digital information, Bosch Security
Systems recommends multiple, redundant recording systems,
and a procedure to back up all analog and digital information.
| 2.0 | 2011.06
Installation Manual
Bosch Security Systems, Inc.
Integrated IR Bullet Camera
1.4
Safety | en
9
FCC & ICES compliance
This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions.1. This device may
not cause harmful interference.2. This device must accept any
interference received, including interference that my cause
undesired operation.
FCC Information
(U.S.A. and Canadian Models Only)
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following
measures:
–
Reorient or relocate the receiving antenna.
–
Increase the separation between the equipment and
–
Connect the equipment into an outlet on a circuit different
receiver.
from that to which the receiver is connected.
–
Consult the dealer, an experienced radio/TV technician, or
Bosch Security Systems for support.
Intentional or unintentional modifications, not expressly
approved by the party responsible for compliance, shall not be
made. Any such modifications could void the user's authority to
operate the equipment. If necessary, the user should consult
the dealer or an experienced radio/television technician for
corrective action. The user may find the following booklet,
prepared by the Federal Communications Commission, helpful:
Bosch Security Systems, Inc.
Installation Manual
| 2.0 | 2011.06
10
en | Safety
Integrated IR Bullet Camera
How to Identify and Resolve Radio-TV Interference Problems.
This booklet is available from the U.S. Government Printing
Office, Washington, DC 20402, Stock No. 004-000-00345-4.
Information FCC et ICES
(modèles utilisés aux États-Unis et au Canada uniquement)
Suite à différents tests, cet appareil s'est révélé conforme aux
exigences imposées aux appareils numériques de classe B, en
vertu de la section 15 du règlement de la Commission fédérale
des communications des États-Unis (FCC), et en vertu de la
norme ICES-003 d'Industrie Canada. Ces exigences visent à
fournir une protection raisonnable contre les interférences
nuisibles lorsque l'appareil est utilisé dans le cadre d'une
installation résidentielle. Cet appareil génère, utilise et émet
de l'énergie de radiofréquences et peut, en cas d'installation ou
d'utilisation non conforme aux instructions, engendrer des
interférences nuisibles au niveau des radiocommunications.
Toutefois, rien ne garantit l'absence d'interférences dans une
installation particulière. Il est possible de déterminer la
production d'interférences en mettant l'appareil
successivement hors et sous tension, tout en contrôlant la
réception radio ou télévision. L'utilisateur peut parvenir à
éliminer les interférences éventuelles en prenant une ou
plusieurs des mesures suivantes:
–
Modifier l'orientation ou l'emplacement de l'antenne
–
Éloigner l'appareil du récepteur.
–
Brancher l'appareil sur une prise située sur un circuit
–
Consulter le revendeur, un technicien qualifié en radio/
réceptrice.
différent de celui du récepteur.
télévision, ou Bosch Security Systems pour obtenir de
l'aide.
Toute modification apportée au produit, non expressément
approuvée par la partie responsable de l'appareil, est
strictement interdite. Une telle modification est susceptible
d'entraîner la révocation du droit d'utilisation de l'appareil.La
brochure suivante, publiée par la Commission fédérale des
| 2.0 | 2011.06
Installation Manual
Bosch Security Systems, Inc.
Integrated IR Bullet Camera
Safety | en
11
communications (FCC), peut s'avérer utile : How to Identify and
Resolve Radio-TV Interference Problems (Comment identifier et
résoudre les problèmes d’interférences de radio et de
télévision). Cette brochure est disponible auprès du U.S.
Government Printing Office, Washington, DC 20402, États-Unis,
sous la référence n° 004-000-00345-4.
NOTICE!
This is a Class B product. In a domestic environment, this
product may cause radio interference, in which case the user
may need to take adequate measures.
1.5
Warranty / Limitation of Liability
The WZ20 Integrated IR Day/Night Bullet Camera has a threeyear warranty.
BOSCH Security Systems warrants that its products, at the
time of shipment by BOSCH Security Systems, are free from
defect in material or workmanship under normal use and
service for the respective warranty periods specified in the
applicable Price Schedule or as otherwise published.
To assure conformance with operating limitations, Buyer should
refer to the applicable data sheet.
The warranty is void (i) if the Product is not operated in
conformance with installation, environmental, mechanical or
electrical requirements, or within thermal stress limits, or (ii) to
the extent that any malfunction is the result of misuse, abuse,
vandalism, neglect, improper installation or application,
alteration, accident, or negligence in use, storage,
transportation, or handling or if the original identification
markings on the product have been removed, defaced or
altered, lightning, electricity, water, fire, environment or other
hazard, or act of God, or other impact outside of normal
operating guidelines.
Bosch Security Systems, Inc.
Installation Manual
| 2.0 | 2011.06
12
en | Safety
Integrated IR Bullet Camera
The foregoing warranty is subject to Buyer’s (i) promptly
written claim and (ii) timely provision to BOSCH Security
Systems of an opportunity to inspect and test the Product
claimed to be defective. Such inspection may be on Buyer’s
premises and/or BOSCH Security Systems may request the
return of the Product at Buyer’s expense. However, BOSCH
Security Systems shall not be responsible for packing,
inspection, or labor costs in connection with the return of
Product. No Product shall be accepted for warranty service that
is not accompanied by a Return Authorization issued by BOSCH
Security Systems.
The liability of BOSCH Security Systems hereunder or
otherwise is solely and exclusively limited to replacement (new
or refurbished Product), repair, or credit of the amortized
purchase price, as BOSCH Security Systems may elect, for any
Product which is returned by Buyer during the applicable
warranty period, or services for which timely notice of defect
has been given by Buyer, and which are found by BOSCH
Security Systems to be subject to adjustment under this
warranty.
BOSCH Security Systems’ warranty shall not be enlarged,
diminished, or affected by, and no obligation or liability shall
arise or grow out of BOSCH Security Systems’ rendering or
technical advice, facilities, or services in connection with
Buyer’s order to the products furnished hereunder.
For more information about the warranty on this product, see
the Warranty Repair section on Bosch’s Customer Care web
page at www.boschsecurity.us/en-us/Service/CustomerCare.
NOTICE!
Do not remove the serial sticker for the warranty service. Doing
so will void the warranty.
| 2.0 | 2011.06
Installation Manual
Bosch Security Systems, Inc.
Integrated IR Bullet Camera
1.6
Safety | en
13
Contact Information
Americas
Bosch Security Systems, Inc.
130 Perinton Parkway
Fairport, New York, 14450
USA
Phone: +1 800 289 0096
Fax: +1 585 223 9180
security.sales@us.bosch.com
www.boschsecurity.us
Europe, Middle East, Africa
Bosch Security Systems B.V.
P.O. Box 80002
5600 JB Eindhoven, The Netherlands
Phone: + 31 40 2577 284
Fax: +31 40 2577 330
emea.securitysystems@bosch.com
www.boschsecurity.com
Asia-Pacific
Robert Bosch (SEA) Pte Ltd, Security Systems
11 Bishan Street 21
Singapore 573943
Phone: +65 6258 5511
Fax: +65 6571 2698
apr.securitysystems@bosch.com
www.boschsecurity.asia
Bosch Security Systems, Inc.
Installation Manual
| 2.0 | 2011.06
14
en | Introduction
Integrated IR Bullet Camera
2
Introduction
2.1
Description
The WZ20 Integrated IR Bullet camera is a night vision DSP
color CCD camera with 1/3 in. LXR CCD with dual-window
mechanical filter. The camera can be installed easily in most
indoor locations.
Features include:
–
Day/night mode (automatic, photocell-controlled)
–
Privacy masking
–
Digital signal processing (DSP)
–
High resolution 550 TVL
–
Even-distribution infrared LED array with 30 LEDs
–
Photocell LED control
–
Operates at temperature range from -30 °C to +55 °C
(-22 °F to 131 °F) at up to 90% humidity (non-condensing)
–
2.2
IP66 rating
Parts List
Quantity Item
1
WZ20 Integrated IR Bullet camera
1
Hex key
4
Mounting screws
1
Installation Manual
Note: Sunshield included. Power supply not included.
| 2.0 | 2011.06
Installation Manual
Bosch Security Systems, Inc.
Integrated IR Bullet Camera
3
Installation | en
15
Installation
CAUTION!
To prevent humidity problems, the camera must be installed in
dry conditions.
1.
Select a mounting surface that is strong enough to support
the camera and that is far from electric or magnetic fields
as well as high temperatures.
2.
Connect the camera to either a 12VDC (recommended for
best picture and the most stable camera operation) or 24
VAC regulated power supply (not included).
3.
Connect the BNC cable to your video monitor.
4.
Face the camera away from the sun or any bright or
reflective light. Excess light on the lens may cause smear
on the picture and possible damage to the CCD.
5.
Tighten the four (4) mounting screws of the bracket.
CAUTION!
To ensure reliable operation in wet or moist conditions, the
cable leads should be sealed once connected.
Figure 3.1 Connection
Bosch Security Systems, Inc.
Installation Manual
| 2.0 | 2011.06
16
en | Configuration
Integrated IR Bullet Camera
4
Configuration
4.1
Configuration Overview
The figure below displays the controls on the bottom of the
camera or on the mounting bracket that are available for
camera adjustment. The tables below each figure identify each
control.
Figure 4.1
Number
1
2
3
4
5
6
7
8
| 2.0 | 2011.06
WZ20 Configuration
Description
2nd Video Output
Joystick
Focus adjustment
Zoom adjustment
Other camera controls
Rotate
Tilt
Pan
Installation Manual
Bosch Security Systems, Inc.
Integrated IR Bullet Camera
4.1.1
Configuration | en
17
Adjusting Pan, Tilt, Rotate
1.
Locate the 3 set screws on the bracket, as identified (6, 7,
8) in the figure above.
2.
Loosen the 3 set screws using the supplied hex key.
3.
Adjust the pan, tilt, and rotate as necessary.
NOTICE!
Do not pan or rotate beyond 360˚ as shown in the figure below.
Do not tilt beyond 90˚ as shown.
Do not apply excessive force when adjusting the camera
positioning.
Figure 4.2 Camera Pan, Tilt, and Rotate
4.1.2
Adjusting Focus
1.
Remove the cap covering the bottom of the camera.
2.
Adjust the focus knob as necessary (see Figure 4.1 above).
3.
Replace the cap over the bottom of the camera.
Bosch Security Systems, Inc.
Installation Manual
| 2.0 | 2011.06
18
en | Configuration
4.1.3
Adjusting Zoom
1.
| 2.0 | 2011.06
Integrated IR Bullet Camera
Remove the cap covering the bottom of the camera.
2.
Adjust the zoom knob as necessary (see Figure 4.1 above).
3.
Replace the cap over the bottom of the camera.
Installation Manual
Bosch Security Systems, Inc.
Integrated IR Bullet Camera
On-Screen Menu | en
5
On-Screen Menu
5.1
OSD Menu
Exposure Color
5.1.1
Day/Night Function Motion Privacy Set
19
Exit
Exposure Submenu
This menu allows you to set and adjust the lens functions.
LENS
E. SHUTTER
BLC
AGC
–
MANUAL/DC
AUTO~1/100000
OFF~36dB
MANUAL/DC: A setting for switching between manual and
DC operation of the lens.
–
E. SHUTTER: Electronic Shutter - A function that allows you
to set the shutter speed (from 1/60(50) to 1/100K).
–
BLC: Backlight Compensation - A function for overcoming
(compensating for) the light behind the object of interest
in a scene. BLC selectively amplifies parts of the image to
compensate for large contrast differences when part of the
image is very brightly lit (for example, a person in a sunlit
doorway).
–
AGC: Automatic Gain Control - A function for regulating the
gain or amplification as the light level decreases and the
lens opens fully.
Bosch Security Systems, Inc.
Installation Manual
| 2.0 | 2011.06
20
en | On-Screen Menu
5.1.2
Integrated IR Bullet Camera
Color Submenu
This menu allows you to control and adjust the RGB level for
the camera to represent accurate white color.
WB MODE
AWC
ATW
MANUAL
PUSH LOCK
–
WB MODE: White Balance Mode
–
AWC: Auto White Balance - A function that allows a color
camera to adjust its output color automatically to give a
natural color independent of the lighting used.
–
ATW: Auto Tracking White balance - A function that allows
the camera to adjust white balance constantly for optimal
color reproduction.
–
MANUAL: A function that allows manual adjustment of the
–
PUSH LOCK: A function that enables you to set up
white balance.
automatically, readjusted only at the request of the user.
| 2.0 | 2011.06
Installation Manual
Bosch Security Systems, Inc.
Integrated IR Bullet Camera
5.1.3
On-Screen Menu | en
21
Day/Night Submenu
This menu allows you to set the day/night mode in order to
adjust the output image depending on the light levels.
D&N MODE
–
AUTO
COLOR
B/W
AUTO: In this mode, the camera output switches
automatically between color and day/night modes,
depending on light levels.
–
COLOR: In this mode, the camera output is only in color.
–
B/W: In this mode, the camera output is only in black and
white.
5.1.4
Function Submenu
This menu allows you to set and adjust the various camera
functions.
MIRROR
SHARPNESS
GAMMA
SLC
HME
DRC
Bosch Security Systems, Inc.
SET LEVEL
SET LEVEL
Installation Manual
| 2.0 | 2011.06
22
en | On-Screen Menu
Integrated IR Bullet Camera
–
MIRROR: A function that enables you to set up reversed
–
SHARPNESS: A function that enables you to set up
–
GAMMA: A function that enables you to set up
–
SLC: Side Light Compensation - Select this mode when the
LEFT and RIGHT images.
sharpness control.
compensation according to gamma value.
corner of the screen is darker than the center. As the level
increases, the image becomes brighter.
–
HME: Highlight Masking Exposure - This function masks the
bright areas on the screen. As the level of HME is
increased, the masking area increases.
–
DRC: Dynamic Range Compensation - This function is to
compensate darker images when different exposures are
in one scene.
5.1.5
Motion Submenu
This menu allows you to set the parameters for the camera to
monitor the movement of the image in 64 different areas of the
screen, and trigger an alarm that appears on the screen.
ALARM
SET WINDOW
ALL SET
ALL CLEAR
SENSITI.
SHOW INDI.
DELAY OUT
| 2.0 | 2011.06
Installation Manual
Bosch Security Systems, Inc.
Integrated IR Bullet Camera
–
On-Screen Menu | en
23
SET WINDOW: With the joystick, select or deselect areas
where you want to detect motion. Only areas in blue are
monitored for movement; the others are ignored/masked.
Figure 5.1 Set Motion Detection area
–
ALL SET: Set the entire screen for movement detection.
–
ALL CLEAR: Clear the entire screen for movement
detection
–
SENSITI.: Sensitivity level - As the sensitivity level
increases, smaller movements are detected.
–
SHOW INDI.: The motion detected indicator can be
selected as icon, trace or off.
–
DELAY OUT: The alarm signal display on the screen is
delayed from 1 second to 15 seconds.
5.1.6
Privacy Submenu
This menu allows you to set and adjust the privacy functions
that prevent the camera from viewing parts of the scene.
MASK 1
MASK 2
MASK 3
MASK 4
COLOR SET
Bosch Security Systems, Inc.
SET WINDOW
SET WINDOW
SET WINDOW
SET WINDOW
Installation Manual
| 2.0 | 2011.06
24
en | On-Screen Menu
–
Integrated IR Bullet Camera
MASK 1 - MASK 4: These are the four (4) mask areas that
you can set.
–
COLOR SET: A function that enables you to select the color
of the masking cells.
Figure 5.2
Privacy Mask
If “SET WINDOW” is selected, the cell appears on the screen.
To adjust the cell, move the joystick UP / DOWN / RIGHT / LEFT.
Once you have selected the desired privacy mask area, press
the joystick in until the mask area is black, and then move the
joystick any direction to return to the previous screen.
5.1.7
Setup Submenu
This menu allows you to set miscellaneous parameters for the
OSD such as camera ID, language, etc.
CAMERA ID
TITLE EDIT
TITLE RESET
TITLE POSITION
DPC SET
WHITE THR.
BLACK THR.
LANGUAGE
PC CONT.
| 2.0 | 2011.06
DPC LEVEL
ENG/CHA
Installation Manual
Bosch Security Systems, Inc.
Integrated IR Bullet Camera
–
On-Screen Menu | en
25
CAMERA ID: This is where you set the ID (title) of the
camera.
–
TITLE EDIT: This is where you select the value for the
camera title.
–
TITLE RESET: This is where you clear the value of the
camera title.
–
TITLE POSITION: This is where you select the area to
display the title.
–
DPC SET: Defect Pixel Cancellation Set - This function
automatically removes dead pixels in real time.
–
LANGUAGE: This is where you set the language (English,
Chinese).
–
PC CONT.: This function enables you to set PC
communication (by selecting ON).
5.1.8
Exit Submenu
This menu allows you to exit the OSD menu with or without
saving your settings.
EXIT
SAVE & EXIT
FACTORY SET
–
EXIT: Exit the OSD menu.
–
SAVE & EXIT: Save your settings and then exit the OSD
menu.
–
FACTORY SET: Restore the factory defaults of the OSD
menu.
NOTICE!
The settings for Lens, Day & Night, and ID/Title stay the same
even after a FACTORY SET.
Bosch Security Systems, Inc.
Installation Manual
| 2.0 | 2011.06
26
en | Troubleshooting
Integrated IR Bullet Camera
6
Troubleshooting
6.1
Troubleshooting Tips
Before sending the camera out for repair, check the items
below. If the problem persists after checking these items,
contact your service center.
- If no image appears, verify that:
–
The coaxial cable is attached securely.
–
The power and voltage are normal.
–
The iris of the lens inside the camera was adjusted
correctly (with the level volume).
–
There is adequate illumination.
- If the image is unclear, verify that:
–
–
The lens is in focus.
The lens is not dirty. Dirt or fingerprints on the lens can
adversely affect the images. Gently wipe any dirt or
fingerprints off the lens with a soft cloth or lens cleaning
paper and cleaning fluid (available commercially).
–
| 2.0 | 2011.06
The monitor is adjusted correctly.
Installation Manual
Bosch Security Systems, Inc.
Integrated IR Bullet Camera
7
Technical Specifications | en
27
Technical Specifications
PV72-CB93H_TM-EX-TDN5-AC8A-30IR-HEATER
Part numbers: WZ20NXV550-0 (NTSC) | WZ20PXV550-0 (PAL)
Electrical
Power
12 VDC
10 - 16 V
consumption
24 VAC
20 - 28 V
with
DC = Max 6.7 W
LED on
AC = Max 8 W (with infrared on)
Video
Signal Format
NTSC
PAL
Signal processing
Output signal
1V P-P composite video, 75 Ohms
CCD Type
1/3 in. 410 K
1/3 in. 470 K
Pixels Color
Pixels Color
Horizontal
520 TVL (Color)
Resolution
560 TVL (TDN/B&W)
Effective Pixels
811 x 508
Lens
IR-corrected, varifocal 5 - 50 mm
Iris
DC auto iris, externally adjustable
Signal-to-Noise
> 48 - 50 dB or more (with AGC off)
795 x 596
Ratio
Sensitivity/
0.1 Lux (F1.2, 30 IRE) (Color)
Min. Illumination
0.001 Lux (F1.2, 30 IRE) (TDN/B&W)
0 Lux (with infrared on)
Gamma
0.45
Sync System
Internal/External
IR wavelength
850 nm
Bosch Security Systems, Inc.
Installation Manual
| 2.0 | 2011.06
28
en | Technical Specifications
Integrated IR Bullet Camera
Mechanical
Dimension
Φ 98 mm x 202 mm (L)
Weight
1.7 kg (3.8 lbs)
Construction
Robust aluminum extrusion
Finish
Anodized silver
Camera Pan/Tilt Range Pan: 360° total
Tilt: 90° total
Environmental
Rating
IP66
Operating Temperature -30 °C to +55 °C (-22 °F to 131 °F)
| 2.0 | 2011.06
Storage Temperature
-20 °C to +70 °C (-4 °F to 158 °F)
Operating Humidity
under 90% (non-condensing)
Installation Manual
Bosch Security Systems, Inc.
Integrated IR Bullet Camera
Technical Specifications | en
29
Dimensions
Below are several dimensional drawings of the camera. Unit of
measure is mm.
Figure 7.1
Front view
Figure 7.2
Top view
Bosch Security Systems, Inc.
Installation Manual
| 2.0 | 2011.06
30
en | Technical Specifications
| 2.0 | 2011.06
Integrated IR Bullet Camera
Installation Manual
Bosch Security Systems, Inc.
Bosch Security Systems, Inc.
850 Greenfield Road
Lancaster, PA 17601
U.S.A.
www.boschsecurity.com
© Bosch Security Systems, Inc., 2011