Bosch EnviroDome Installation manual

AutoDome® and EnviroDome®
Indoor Pendant
In-ceiling Model
Installation Manual
Version 5.3
EN
Security you can rely on
EN
Important Safeguards
Important Safeguards
1. Read, Follow, and Retain Instructions - All safety and
operating instructions should be read and followed before
operating the unit. Retain instructions for future reference.
2. Heed Warnings – Adhere to all warnings on the unit and in
the operating instructions.
3. Attachments - Attachments not recommended by the product manufacturer should not be used, as they may cause hazards.
4. Installation Cautions - Do not place this unit on an unstable stand, tripod, bracket, or mount. The unit may fall, causing serious injury to a person and serious damage to the
unit. Use only manufacturer-recommended accessories, or
those sold with the product. Mount the unit per the manufacturer's instructions. Appliance and cart combination
should be moved with care. Quick stops, excessive force, or
uneven surfaces may cause the appliance and cart combination to overturn.
5. Cleaning - Unplug the unit from the outlet before cleaning.
Follow any instructions provided with the unit. Generally,
using a damp cloth for cleaning is sufficient. Do not use liquid cleaners or aerosol cleaners.
6. Servicing - Do not attempt to service this unit yourself.
Opening or removing covers may expose you to dangerous
voltage or other hazards. Refer all servicing to qualified service personnel.
7. Damage Requiring Service - Unplug the unit from the
main AC power source and refer servicing to qualified service personnel under the following conditions:
• When the power supply cord or plug is damaged.
• If liquid has been spilled or an object has fallen into the
unit.
• If the unit has been exposed to water and/or inclement
weather (rain, snow, etc.).
• If the unit does not operate normally, when following the
operating instructions. Adjust only those controls specified
in the operating instructions. Improper adjustment of other
controls may result in damage, and require extensive work
by a qualified technician to restore the unit to normal
operation.
• If the unit has been dropped or the cabinet damaged.
• If the unit exhibits a distinct change in performance, this
indicates that service is needed.
8. Replacement Parts - When replacement parts are required,
the service technician should use replacement parts specified
by the manufacturer, or that have the same characteristics as
the original part. Unauthorized substitutions may result in
fire, electrical shock, or other hazards.
9. Safety Check - Upon completion of servicing or repairs to
the unit, ask the service technician to perform safety checks
to ensure proper operating condition.
© 2005 Bosch Security Systems
10. Power Sources - Operate the unit only from the type of
power source indicated on the label. If unsure of the type of
power supply to use, contact your dealer or local power
company.
• For units intended to operate from battery power, refer to
the operating instructions.
• For units intended to operate with External Power
Supplies, use only the recommended approved power
supplies.
• For units intended to operate with a limited power source,
this power source must comply with EN60950.
Substitutions may damage the unit or cause fire or shock.
• For units intended to operate at 24 VAC, normal input
voltage is 24 VAC. Voltage applied to the unit's power
input should not exceed 30 VAC. User-supplied wiring,
from the 24 VAC supply to unit, must be in compliance
with electrical codes (Class 2 power levels). Do not ground
the 24 VAC supply at the terminals or at the unit's power
supply terminals.
11. Coax Grounding - If an outside cable system is connected
to the unit, ensure that the cable system is grounded. U.S.A.
models only--Section 810 of the National Electrical Code,
ANSI/NFPA No.70, provides information regarding proper
grounding of the mount and supporting structure, grounding
of the coax to a discharge unit, size of grounding conductors,
location of discharge unit, connection to grounding electrodes, and requirements for the grounding electrode.
12. Grounding or Polarization - This unit may be equipped
with a polarized alternating current line plug (a plug with
one blade wider than the other). This safety feature allows
the plug to fit into the power outlet in only one way. If
unable to insert the plug fully into the outlet, try reversing
the plug. If the plug still fails to fit, contact an electrician to
arrange replacement of the obsolete outlet. Do not defeat the
safety purpose of the polarized plug.
Alternately, this unit may be equipped with a 3-wire grounding plug (a plug with a third pin, for grounding). This safety
feature allows the plug to fit into a grounding power outlet
only. If unable to insert the plug into the outlet, contact an
electrician to arrange replacement of the obsolete outlet. Do
not defeat the safety purpose of the grounding plug.
13. Lightning - For added protection during a lightning storm,
or when this unit is left unattended and unused for long periods of time, unplug the unit from the wall outlet and disconnect the cable system. This will prevent damage to the unit
due to lightning and power line surges.
Page 2 of 36
EN
For Indoor Product
1. Water and Moisture - Do not use this unit near
water - for example, in a wet basement, in an
unprotected outdoor installation, or in any area
classified as a wet location.
2. Object and Liquid Entry - Never push objects of
any kind into this unit through openings, as they
may touch dangerous voltage points or short out
parts that could result in a fire or electrical shock.
Never spill liquid of any kind on the unit.
3. Power Cord and Power Cord Protection - For
units intended to operate with 230VAC, 50Hz,
the input and output power cord must comply
with the latest versions of IEC Publication 227 or
IEC Publication 245.
Power supply cords should be routed so they are
not likely to be walked on or pinched. Pay particular attention to location of cords and plugs, convenience receptacles, and the point of exit from
the appliance.
4. Overloading - Do not overload outlets and
extension cords; this can result in a risk of fire or
electrical shock.
For Outdoor Product
Power Lines - An outdoor system should not be
located in the vicinity of overhead power lines,
electric lights, or power circuits, or where it may
contact such power lines or circuits. When
installing an outdoor system, extreme care should
be taken to keep from touching power lines or
circuits, as this contact might be fatal. U.S.A.
models only - refer to the National Electrical
Code Article 820 regarding installation of CATV
systems.
Safety Precautions
Safety Precautions
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR
BACK). NO USER SERVICEABLE PARTS
INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
This symbol indicates the presence of uninsulated “dangerous voltage” within the product’s enclosure that can cause an electric
shock.
This symbol indicates the presence of
important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
Installation should be performed by qualified
service personnel only in accordance with the
National Electrical Code or applicable local
codes.
Power Disconnect. Units with or without
ON-OFF switches have power supplied to the
unit whenever the power cord is inserted into the
power source; however, the unit is operational
only when the ON-OFF switch is in the ON position. The power cord is the main power disconnect for all units.
For Rack-Mount Product
1. Ventilation - This unit should not be placed in a
built-in installation or rack, unless proper ventilation is provided, or the manufacturer’s instructions have been adhered to. The equipment must
not exceed its maximum operating temperature
requirements.
2. Mechanical Loading - Mounting of the equipment in a rack shall be such that a hazardous condition is not achieved due to uneven mechanical
loading.
© 2005 Bosch Security Systems
Page 3 of 40
EN
FCC & ICES INFORMATION
Safety Precautions
Sécurité
(U.S.A. and Canadian Models Only)
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference,
and
(2) This device must accept any interference
received, including interference that may cause
undesired operation.
NOTE: This equipment has been tested and found to
comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules and ICES-003 of
Industry Canada. These limits are designed to provide
reasonable protection against harmful interference
when the equipment is operated in a commercial
environment. This equipment generates, uses and radiates radio frequency energy, and if not installed and
used in accordance with the instruction manual, may
cause harmful interference to radio communications.
Operation of this equipment in a residential area is
likely to cause harmful interference, in which case the
user will be required to correct the interference at his
expense.
Intentional or unintentional changes or modifications,
not expressly approved by the party responsible for
compliance, shall not be made. Any such changes
or modifications could void the user’s authority to
operate the equipment. If necessary, the user should
consult the dealer or an experienced radio/television
technician for corrective action.
The user may find the following booklet, prepared by
the Federal Communications Commission, helpful:
How to Identify and Resolve Radio-TV Interference
Problems. This booklet is available from the U.S.
Government Printing Office, Washington, DC 20402,
Stock No. 004-000-00345-4.
WARNING: This is a Class A product. In a domestic
environment, this product may cause radio interference, in which case, the user may be required to take
adequate measures.
ATTENTION : POUR ÉVITER TOUT RISQUE D'ÉLECTROCUTION,
N'ESSAYEZ PAS DE RETIRER LE CAPOT (OU LE PANNEAU
ARRIÈRE). CET APPAREIL NE CONTIENT AUCUN COMPOSANT
SUSCEPTIBLE D'ÊTRE RÉPARÉ PAR L'UTILISATEUR. CONFIEZ
LA RÉPARATION DE L'APPAREIL À DU PERSONNEL QUALIFIÉ.
Ce symbole signale que le produit renferme une « tension potentiellement dangereuse » non isolée susceptible de provoquer une
électrocution.
Ce symbole invite l'utilisateur à consulter les instructions d'utilisation et d'entretien (dépannage) reprises dans la documentation qui accompagne l'appareil.
Attention : l'installation doit exclusivement être réalisée par du personnel qualifié, conformément au code national d'électricité américain (NEC) ou au code d'électricité local en vigueur.
Coupure de l'alimentation. Qu'ils soient pourvus ou non d'un commutateur ON/OFF, tous les appareils reçoivent de l'énergie une fois
le cordon branché sur la source d'alimentation. Toutefois, l'appareil
ne fonctionne réellement que lorsque
le commutateur est réglé sur ON. Le débranchement du cordon d'alimentation permet de couper l'alimentation des appareils.
Sicherheitshinweise
VORSICHT: UM EINEN ELEKTRISCHEN SCHLAG ZU VERMEIDEN, IST DIE ABDECKUNG (ODER RÜCKSEITE) NICHT ZU
ENTFERNEN. ES BEFINDEN SICH KEINE TEILE IN DIESEM
BEREICH, DIE VOM BENUTZER GEWARTET WERDEN KÖNNEN. LASSEN SIE WARTUNGSARBEITEN NUR VON QUALIFIZIERTEM WARTUNGSPERSONAL AUSFÜHREN.
Das Symbol macht auf nicht isolierte „gefährliche Spannung"
im Gehäuse aufmerksam. Dies kann zu einem elektrischen
Schlag führen.
Der Benutzer sollte sich ausführlich über Anweisungen für
die Bedienung und Instandhaltung (Wartung) in den begleitenden Unterlagen informieren.
Achtung! Die Installation sollte nur von qualifiziertem
Kundendienstpersonal gemäß jeweils zutreffender
Elektrovorschriften ausgeführt werden.
Unterbrechung des Netzanschlusses. Geräte mit oder ohne
Netzschalter haben Spannung am Gerät anliegen, sobald der
Netzstecker in die Steckdose gesteckt wird. Das Gerät ist jedoch
nur betriebsbereit, wenn der Netzschalter (EIN/AUS) auf EIN
steht. Wenn das Netzkabel aus der Steckdose gezogen wird, ist
die Spannungszuführung zum Gerät vollkommen unterbrochen.
© 2005 Bosch Security Systems
Page 4 of 40
EN
Precauciones de Seguridad
PRECAUCIÓN: PARA DISMINUIR EL RIESGO DE DESCARGA
ELÉCTRICA, NO RETIRE LA CUBIERTA (NI LA PARTE POSTERIOR). NO EXISTEN PIEZAS DE RECAMBIO EN EL INTERIOR
DEL EQUIPO. EL PERSONAL DE SERVICIO CUALIFICADO SE
ENCARGA DE REALIZAR LAS REPARACIONES.
Safety Precautions
Sicurezza
ATTENZIONE: PER RIDURRE IL RISCHIO DI SCOSSE ELETTRICHE NON RIMUOVERE LA COPERTURA (O IL PANNELLO
POSTERIORE). L'UNITÀ NON CONTIENE COMPONENTI
INTERNI RIPARABILI DALL'UTENTE. PER QUALSIASI INTERVENTO, RIVOLGERSI A PERSONALE TECNICO QUALIFICATO.
Este símbolo indica que existen puntos de tensión peligrosos
sin aislamiento dentro de la cubierta de la unidad. Estos puntos pueden constituir un riesgo de descarga eléctrica.
Questo simbolo indica la presenza di "tensione pericolosa" non
isolata all'interno del contenitore del prodotto. Ciò comporta un
potenziale rischio di scosse elettriche.
El usuario debe consultar las instrucciones de funcionamiento y
mantenimiento (reparación) en la documentación que se suministra con el aparato.
Si consiglia di consultare le istruzioni operative e di manutenzione (interventi tecnici) contenute nella documentazione fornita con il dispositivo.
Atención: la instalación la debe realizar únicamente personal
cualificado de conformidad con el National Electric Code o las
normas aplicables en su país.
Attenzione: l'installazione deve essere effettuata esclusivamente
da personale tecnico qualificato in conformità con il National
Electrical Code o con le normative locali vigenti.
Desconexión de la alimentación. Las unidades con o sin interruptores de encendido/apagado reciben alimentación eléctrica
siempre que el cable de alimentación esté conectado a la fuente
de alimentación. Sin embargo, la unidad sólo funciona cuando el
interruptor está en la posición de encendido. El cable de alimentación es la principal fuente de desconexión de todas las
unidades.
Scollegamento dell'alimentazione. Le unità dotate o sprovviste di
interruttori ON-OFF vengono alimentate quando si inserisce il
cavo nella presa dell'alimentazione. L'unità è tuttavia in funzione
solo quando l'interruttore ON-OFF si trova nella posizione ON. Il
cavo di alimentazione costituisce il dispositivo di scollegamento dell'alimentazione principale per tutte le unità.
Veiligheidsmaatregelen
VOORZICHTIG: OPEN DE BEHUIZING OF DE ACHTERKANT
VAN HET APPARAAT NIET. ZO VERMINDERT U HET RISICO
OP ELEKTRISCHE SCHOKKEN. IN HET APPARAAT BEVINDEN ZICH GEEN ONDERDELEN DIE U ZELF KUNT REPAREREN. LAAT SERVICE EN ONDERHOUD UITVOEREN DOOR
GEKWALIFICEERD PERSONEEL.
Medidas de Segurança
CUIDADO: PARA REDUZIR O RISCO DE CHOQUE ELÉCTRICO, NÃO RETIRE A TAMPA (OU A PARTE POSTERIOR). NO
INTERIOR, NÃO EXISTEM PEÇAS QUE POSSAM SER
REPARADAS PELO UTILIZADOR. REMETA A ASSISTÊNCIA
PARA OS TÉCNICOS QUALIFICADOS.
Dit symbool geeft aan dat er binnen in het apparaat ongeïsoleerde, gevaarlijke spanning aanwezig is die mogelijk elektrische schokken kan veroorzaken.
Este símbolo indica a presença de "tensão perigosa" não isolada
dentro da estrutura do produto, o que pode constituir risco de
choque eléctrico.
De gebruiker dient de bedienings- en onderhoudsvoorschriften
te raadplegen in de documentatie die werd meegeleverd met
het apparaat.
O utilizador deve consultar as instruções de funcionamento
e manutenção (assistência) nos documentos que acompanham o aparelho.
Attentie: het apparaat mag alleen door gekwalificeerd personeel
worden geïnstalleerd. De installatie dient in overeenstemming
met de nationale elektrische richtlijnen of de van toepassing
zijnde lokale richtlijnen te worden uitgevoerd.
Spanning uitschakelen. Apparatuur met of zonder
aan-uitschakelaar staat onder spanning zolang de stekker is
aangesloten op de wandcontactdoos. De apparatuur is uitsluitend
in werking als de aan-uitschakelaar aan staat. Het netsnoer is de
"hoofdschakelaar" voor alle apparatuur.
© 2005 Bosch Security Systems
Atenção: a instalação deve ser executada apenas por técnicos
qualificados da assistência, de acordo com o código eléctrico
nacional ou os códigos locais aplicáveis.
Corte de corrente. As unidades com ou sem interruptores
ON-OFF (ligar/desligar) recebem corrente sempre que o fio de
alimentação está introduzido na fonte de alimentação; contudo, a
unidade apenas está operacional quando o interruptor ON-OFF
está na posição ON. O fio de alimentação destina-se a desligar a
corrente em todas as unidades.
Page 5 of 40
EN
Safety Precautions
Zasady Bezpieczeƒstwa
PRZESTROGA: ABY ZMNIEJSZYå RYZYKO PORA˚ENIA ELEKTRYCZNEGO, NIE NALE˚Y ZDEJMOWAå POKRYWY GÓRNEJ (ani
tylnej). WEWNÑTRZ URZÑDZENIA NIE MA ˚ADNYCH
ELEMENTÓW, KTÓRE MOGÑ BYå NAPRAWIANE SAMODZIELNIE
PRZEZ U˚YTKOWNIKA. SERWIS NALE˚Y ZLECAå WYKWALIFIKOWANYM PRACOWNIKOM OBS¸UGI.
Ten symbol wskazuje na obecnoÊç nieizolowanego „niebezpiecznego napi´cia” we wn´trzu urzàdzenia. Napi´cie to
grozi pora˝eniem
U˝ytkownik powinien zapoznaç si´ z instrukcjami obsšugi
i konserwacji (serwisu), zamieszczonymi w dokumentacji
Uwaga: Instalacja mo˝e byç wykonywana wyšàcznie przez
wykwalifikowanych pracowników obsšugi, zgodnie z zasadami kodeksu National Electrical Code lub innych obowiàzujàcych norm.
Odšàczanie zasilania Niezale˝nie od wyposa˝enia w
wyšàcznik zasilania, pràd do urzàdzenia jest
doprowadzany zawsze, gdy przewód zasilania jest
podšàczony do êródša zasilania; jednak urzàdzenie
dziaša tylko wtedy, gdy wyšàcznik zasilania jest
© 2005 Bosch Security Systems
Page 6 of 40
EN
Introduction
Table of Contents
SECTION 1
SECTION 1
ENVIRODOME AND INDOOR PENDANT
INSTALLATION INSTRUCTIONS . . . . . . . . . . . . . . . . . . . .7
EnviroDome and Indoor Pendant
Installation Instructions
SECTION 2
IN-CEILING AUTODOME
INSTALLATION INSTRUCTIONS . . . . . . . . . . . . . . . . . . .11
Camera Addressing
1.1 To use FastAddress, skip to STEP 1F. Otherwise, to
manually set the switch address, position the dome on the
star shaped foam, with the bubble side down.
SECTION 3
FASTADDRESS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
SECTION 4
AUTODOME SECURITY . . . . . . . . . . . . . . . . . . . . . . . . . .14
SECTION 5
SECTOR BLANKING AND PRIVACY MASKS . . . . . . . . .15
SECTION 6
CHANGING THE BAUD RATE FOR
RS-232 OR RS-485 OPERATION. . . . . . . . . . . . . . . . . . . . .16
SECTION 7
ALARMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
SECTION 8
AUTOTRACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Photo 1A Position dome
1.2
SECTION 9
PELCO PROTOCOL MODE . . . . . . . . . . . . . . . . . . . . . . . .20
Remove the 4 top screws as shown in PHOTO 1B, and lift
the top plate carefully off the dome. The cable length is
approximately 5 cm (2 in), so remove carefully from the
PCB.
Remove the top plate cable (if necessary) from the dome
to access the address switch. Set the address switch (as in
STEP 1C) and make a note of it.
SECTION 10
MAINTENANCE/COMPONENT
REPLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
SECTION 11
TROUBLESHOOTING GUIDE . . . . . . . . . . . . . . . . . . . . .24
SECTION 12
AUTODOME LOCKED COMMANDS . . . . . . . . . . . . . . .26
SECTION 13
ADVANCED MENU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
APPENDIX A
POWER WIRING GUIDE . . . . . . . . . . . . . . . . . . . . . . . . . .34
APPENDIX B
OPTIONAL GASKET INSTALLATION . . . . . . . . . . . . . . .35
AUTODOME USER MANUAL (Insert) . . . . . . . . . . . . . . . .36
AUTODOME USER COMMANDS
(Unlocked Commands) . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
NOTE: Before beginning installation, please remove the USER
MANUAL in the back of this booklet.
© 2005 Bosch Security Systems
Photo 1B Remove screws
1.3
If using RS-232/RS-485 Communications:
The unit is shipped with the Baud Rate set to 9600. The
baud rate may be changed via the COMMUNICATIONS
SETUP menu (see SECTION 6).
Page 7 of 40
EN
Section 1
The following dip switch settings pertain to AutoDome
Versions 5.00 and newer.
Switch # Function
Position
1
RESERVED
2
Serial Mode Selection
3
RESERVED
4
Low Pressure Detection
1.5
To avoid confusion during installation, write the camera
address on masking tape and stick it to the dome, as
shown in PHOTO 1E.
Selection
The dome is now ready to be installed, using an
appropriate AutoDome mount.
ON
OFF
RS-485
RS-232*
ON
OFF
Pressurized Dome
Non-Pressurized
Dome*
*Default position for all switch settings is OFF.
Figure 1A S105 Dip Switch Settings
Address
Switches
Photo 1E Write camera address
Installation should be performed by qualified service
personnel only, in accordance with the National
Electrical Code or applicable local codes. Refer to the
appropriate installation section.
The AutoDome can be mounted to a wall, mast (pole), roof,
pipe, or a corner mount once the appropriate mount has been
installed. Each mount includes its own mounting instructions.
S105 Dip Switches
Photo 1C Set the address switch
1.4
Reconnect the top plate cable, then replace the top plate
and gasket (see PHOTO 1D). Align the ribs on the bottom of the top plate with the matching openings in the
housing, then firmly tighten the four (4) screws.
Mounts must be properly and securely mounted to a
supporting structure capable of sustaining the unit
weight.**Use care when selecting mounting hardware
(not supplied) for installation. The mounting surface
and unit's weight should be carefully considered.
The following instructions reference a 120/230 VAC
pendant wall plate installation mounted to an existing structure.
The instructions assume the safety cable, power, video, and control cables have already been properly installed.
**Refer to mounting instructions.
Photo 1D Replace top plate
© 2005 Bosch Security Systems
Page 8 of 40
EN
Section 1
b. Connect Video (BNC) cable and the CONTROL
connector. Tighten screws on control connector.
Attach the installation-assist cable* to the eyehook on the
top of the dome, and close the safety cable (see PHOTO
1F).
1.6
c. When using Biphase, and the dome is in a star
configuration (or is the last dome on a daisy chain), it
requires a 110 Ω terminating resistor (included) across
pin 8 (C+) and pin 9 (C–).
* A cable (user-provided) is recommended for safety
purposes when pipe mounting. See Mounting Guide for
instructions.
Daisy chain configuration is not possible if fiber optic
accessory is used.
Installation Assist Cable
BNC Connector
1.8
Eyehook
AUTODOME 24 VAC INSTRUCTIONS
ENVX2450X, ENVX2460X, G3AX5X, and G3AX6X Kits
Check for the following:
a.
8-Pin Alarm
Connector
9-Pin Control
Connector
b. Be sure to use an adequate gauge of 24 VAC wiring for
the distance run. See APPENDIX A - Power Wiring
Guide for proper wiring instructions and recommended
wire run lengths.
Photo 1F Connections
1.7
An ENV-PSU (or equivalent) power supply must be
used.
MAKE THE FOLLOWING CONNECTIONS:
c. Wire the 9-pin CONTROL connector located on the
top of the unit, as in STEP 1G.
**If the AutoDome is programmed for RS-485 operation, RXD
functions as DATA (+), and TXD functions as DATA (–).
d. If the Alarm Inputs or Relay Output are being used,
connect the appropriate wires to the 8-pin Alarm
connector.
CONTROL CONNECTOR
9
8
C–
7
6
5
4
3
2
C+ GND RXD TXD GND H
Top of Dome
24 VAC
Retaining
Screw
24 VAC Hot
24 VAC Neutral
Indoor Pendant - Not Connected
EnviroDome® - 24 VAC Heater
RS-232
Ground
**RS-232 TX
**RS-232 RX
Biphase
Ground
Biphase +
Biphase –
1
Figure 1B Control connector
a. If the Alarm Inputs or the Relay Output are being
used, connect the appropriate wires to the 8-pin Alarm
connector (see FIGURE 1C).
(1) 24 VAC Hot
(2) 24 VAC Neutral
(3) Heater**
(4) RS-232 Ground
(5) RS-232 TXD
(6) RS-232 RXD
(7) Biphase Ground
(8) Biphase +
(9) Biphase –
To ENV-PSU
or
equivalent
ALARM CONNECTOR
8
7
6
5
4
GND A1
A2
A3
A4
3
2
1
**EnviroDome Only
NC COM NO
RETAINING SCREW
Figure 1D
ALARM GROUND
ALARM INPUT #1
ALARM INPUT #2
ALARM INPUT #3
NORMALLY OPEN
RELAY COMMON
NORMALLY CLOSED
ALARM INPUT #4
Figure 1C Alarm connector
© 2005 Bosch Security Systems
If not using an ENV-PSU, place a jumper between
Pin (1) 24 VAC Hot and Pin (3) Heater (see
APPENDIX A for details).
1.9
Align the notch on the AutoDome with the notch on the
FRONT of the Pendant Arm.
Page 9 of 40
EN
Section 1
Lift the AutoDome into the Pendant Arm and twist until
the notch on the AutoDome is aligned with the notch on
the SIDE of the pendant arm.
ALIGN NOTCHES
ROTATE
Photo 1I Installed AutoDome
Photo 1G Align notches
1.10 Tighten the two screws on the top of the
pendant arm until snug.
Photo 1H Tighten screws
Some models require a slotted screw instead of an
Allen screw.
Apply power to the AutoDome.
1.11 If using the FastAddress feature, see SECTION 3 for
additional information.
Congratulations! You’ve installed the AutoDome.
© 2005 Bosch Security Systems
Page 10 of 40
EN
Section 2
If using RS-232/RS-485 Communications:
SECTION 2
The unit is shipped with the RS-232/RS-485 Baud Rate
set to 9600. This rate can be changed via the
COMMUNICATIONS SETUP menu
(see SECTION 6).
In-ceiling AutoDome
Installation Instructions
2.1
The following settings pertain to AutoDome versions 5.00
and newer:
Before installing this unit, install and wire the
In-ceiling Backbox (LTC 7490), following the instructions
provided with that unit.
Carefully remove the AutoDome from the box. Save all
packing material, to be used for setup and transport of
the camera and dome.
If an item appears to have been damaged in shipment,
notify the shipper. If any items are missing, notify your
Bosch Sales or Customer Service Representative at the
location nearest you. See our Web site at
www.boschsecurity.com.
Switch # Function
1
RESERVED
2
Serial Mode Selection
3
RESERVED
4
Low Pressure Detection
Position
Selection
ON
OFF
RS-485
RS-232*
ON
OFF
Pressurized Dome
Non-Pressurized
Dome*
*Default position for all switch settings is OFF.
Figure 2A S105 Dip Switch Settings
S105 Dip Switch
Address Switch
Photo 2B S105 Dip switch and Address selector
Photo 2A In-ceiling AutoDome
2.2
To use FastAddress, skip to STEP 2C. Otherwise, set the
address switch as shown. Setting address selector to 0000
causes the AutoDome to respond to ALL messages regardless
of address (NOT RECOMMENDED); otherwise, the unit
only responds to commands issued for that address.
© 2005 Bosch Security Systems
Page 11 of 40
EN
2.3
Section 2
Attach the dome window to the camera module, aligning
the blue LOCK labels.
2.6
While grasping the unit by the dome window, insert the
camera module completely into the backbox.
Snap the dome cover into position by pressing
gently on the dome 90° from the blue labels.
90°
RED DOTS
FACING
EACH
OTHER
BLUE
LABEL
Photo 2C Attach dome window
2.4
Photo 2F Insert camera module
90°
2.7
While holding the top of the camera, rotate the lower
portion and align the camera dome yellow markers.
While pressing up, twist the dome window/locking ring
clockwise approximately 1/4 turn. The camera will
initialize ten seconds after it is properly installed.
TURN TO
LOCK
YELLOW
MARKERS
Photo 2G Lock dome into place
Photo 2D Align yellow markers
2.8
2.5
With the red dot on the camera module facing the red
dot on the backbox, slide the camera module into the
backbox module using the guides. Note that the camera is
shown turned 180 degrees to illustrate red markers.
An optional tamper clip is provided to prevent the dome
from being removed. To install, locate the blue label,
orient the tamper clip with the two tabs pointing up, and
press the tamper clip into the locking ring just to the
right of either blue label. A straight blade screwdriver
will help push the clip in place.
RED
MARKERS
Photo 2E Align red markers
© 2005 Bosch Security Systems
Page 12 of 40
EN
Section 3
SECTION 3
FastAddress
The FastAddress feature allows the AutoDome’s cameras to be
addressed (or the address may be changed) via a keyboard and
on-screen menus instead of using the switch address (thumbwheel). If FastAddress is not used, the camera’s address defaults
to the address indicated by the thumbwheel switches.
Conversely, if FastAddress has been programmed, the
thumbwheel switches are ignored.
There are two commands used to address the AutoDome via the
FastAddress feature:
•
ON-999-ENTER: All domes that have not already been
configured using FastAddress will respond to this command.
Additionally, if the address of a previously configured dome
matches the camera number at the keyboard, that dome will
respond to the command as well.
•
ON-998-ENTER: All domes respond to this command,
regardless of FastAddress status.
Photo 2H Optional tamper clip
2.9
To install the trim ring, align the yellow dots on the
inside of the trim ring with the yellow dots on the locking
ring. To ensure proper installation, push on the trim ring
vertically until a click is felt. Installation is now complete.
If using the FastAddress feature, see SECTION 3 for
additional information.
2.10 INSTALLATION
Installation should be performed by qualified service
personnel only, in accordance with the National
Electrical Code or applicable local codes.
The AutoDome system is suitable for use in environmental air
spaces or in an air handling plenum of a nonfire-resistant
ceiling.
Do not remove camera from pan/tilt. Remove the entire
receiver/driver, pan/tilt, and camera assembly from the
AutoDome system to prevent damage to the
flexible cable and connector.
NOTE: In systems with multiple monitors, other domes may
also enter the FastAddress mode. As commands (which are
unique for each dome) are entered, the other domes
automatically exit the FastAdress mode, and only the target
dome remains active. Following are some instances when
FastAddress would be used:
1. New or existing installation of an AutoDome(s):
a. Set the keyboard to display the camera, for example,
CAMERA-3-ENTER (where 3 is the camera whose
address you’re identifying/changing).
b. Press ON-999-ENTER, and follow the instructions on the
screen (see FIGURE 3A).
REMINDER: All domes that have not already been
configured using FastAddress will respond to
ON-999-ENTER.
c. When a camera is being moved, the dome may
already have an address, therefore it will not respond to
ON-999-ENTER. In this case, you must use
ON-998-ENTER to readdress the camera, then follow the
on-screen instructions.
d. There is a visual confirmation that the address was set.
2. Clearing the address of a camera (causing the address of the
camera to revert back to the address set by the thumbwheel):
a. Enter FastAddress mode using either method described
above, then follow the on-screen instructions
(see FIGURE 3B).
b. At the end of FastAdress mode, press OFF-1-ENTER to
clear the address.
© 2005 Bosch Security Systems
Page 13 of 40
EN
c. There is a visual confirmation that the address was cleared.
Use ON-997-ENTER to check/confirm camera addresses.
For example, if referring to Camera 3, press
CAMERA-3-ENTER, then ON-997-ENTER. This causes all
cameras to briefly display their addresses.
FastAddress is stored to nonvolatile memory, thus will not change
if power is removed or factory defaults are restored
(SET-899-ENTER).
Section 4
SECTION 4
AutoDome SECURITY
The AutoDome has password protection capability for
Advanced Menu access and other locked commands.
To set a password, after entering OFF-90-ENTER, enter
SET-802-ENTER and follow the on-screen instructions to set or
change the password. Passwords are four (4) digits in length and
are selected via the joystick.
The AutoDome's default password of 0000 <four zeros> allows
OFF-90-ENTER to directly unlock the Advanced Menu
commands. If the password of 9999 is used, the AutoDome is
totally unlocked so that all AutoDome commands can be
executed (no OFF-90-ENTER is required to use ADVANCED
COMMANDS).
If any other 4-digit password is set, the AutoDome prompts for
entry of a password when the unlock command,
OFF-90-ENTER, is entered.
Figure 3A Enter new address
Figure 3B Clearing address
© 2005 Bosch Security Systems
Page 14 of 40
EN
Section 5
TO CREATE A MASK:
SECTION 5
1.
First, use the joystick to maneuver to the area to be masked,
then zoom in so that this area is between 25% to 50% of
the total screen.
2.
Press ON-87-ENTER to enter the menu (as shown in
FIGURE 5A). Use the joystick to scroll through the list of
masks until the desired mask is highlighted. Press Focus+
to edit this mask.
3.
If desired, use the joystick to adjust the area to be masked.
Pan, Tilt, and Zoom are all available to reposition the
camera to the view that is to be masked. Press FOCUS to
continue (as shown in FIGURE 5B).
SECTOR BLANKING AND PRIVACY MASKS
SECTOR BLANKING simply blanks all
video in a specified sector. Sectors are
defined as 1/16 of the total 360° field-ofview. Any combination of these sectors can
be blanked via the BLANKING MENU,
ON-86-ENTER.
13
14 15
16
12
1
2
11
10
3
9
4
8
7
6
5
PRIVACY MASKS give the installer the
opportunity to black out (mask) areas from visibility. Up to six (6)
rectangular Privacy Masks can be defined. These masks change
location and size as the camera pans, tilts and zooms.
When entering the PRIVACY MASKING screen
(ON-87-ENTER), a list of masks is displayed for on-screen
selection. An * at the front of the line indicates that the mask is
currently occupied, and if selected, the mask will be overwritten. The first available (unused) Privacy Mask is indicated by an
arrow at the left margin, as shown below in FIGURE 5A.
Figure 5B Reposition Camera
4.
Use the joystick to move the masking block to the center of
the area to be masked. Press either FOCUS button to
anchor the mask (as shown in FIGURE 5C).
Figure 5A Privacy Masking menu
Use the joystick to scroll through the list of masks until the desired
mask is highlighted.
While in the PRIVACY MASKING menu, the following
commands are available:
• FOCUS+ draws a new Privacy Mask (or edits an existing
mask). A 1x1 block is drawn in the center of the screen (as
shown in FIGURE 5B).
Figure 5C Move Block
5.
Use the joystick to modify the mask's dimensions by moving
to the right and down. Ensure that the mask is larger than the
object/area to be masked (as shown in FIGURE 5D).
• FOCUS– deletes the selected mask (and removes
the *, signifying that the mask is now unused).
• IRIS+ moves the AutoDome so that the highlighted
mask is centered on the screen.
• IRIS– exits the menu.
Figure 5D Modify Mask
© 2005 Bosch Security Systems
Page 15 of 40
EN
6.
Press FOCUS again to continue. The AutoDome now
adjusts its zoom position and allows fine-tuning of the
mask coverage by using the joystick. FIGURE 5E shows a
sample mask.
Section 6
3.
Use the joystick to move down to the Communication
Setup menu and press FOCUS on the controller/keyboard.
Figure 6B Communication Setup
Figure 5E Adjusts Mask
7.
When finished fine-tuning the mask, press either IRIS
button to exit the menu and save the current mask. Verify
sufficient mask coverage by panning, tilting and zooming
through the field-of-view.
SECTION 6
4.
Press and release FOCUS until the desired baud rate
appears. Then press IRIS to SAVE and EXIT.
5.
A countdown message will appear to confirm the baud
rate change. If the baud rate of the controller is changed
within 60 seconds, and the joystick is moved in any direction, the baud rate will be saved and made active. If the
joystick is not moved at all, the AutoDome will discard
the change and revert back to the previous baud rate.
CHANGING THE COMMUNICATION
SETUP FOR RS-232, RS-485 OR Bilinx™
If RS-232 or RS-485 is used to control the AutoDome, the baud
rate may be changed via the following steps:
1.
View the video from the camera on a monitor. Using an
appropriate controller/keyboard, unlock the AutoDome
menus using OFF-90-ENTER.
COMMAND: UNLOCKED should briefly appear at the
top of the monitor.
2.
Enter the Setup menu using ON-46-ENTER. The main
Setup menu should appear, as follows:
Figure 6C Baud Rate Confirmation
Figure 6A Camera Setup
© 2005 Bosch Security Systems
Versions 5.10 and higher of the AutoDome can also communicate directly through the coax using BILINX. The BILINX data
communications may be disabled by changing the menu selection to OFF.
1.
Use the joystick to move down to the BILINX selection
and press FOCUS on the controller/keyboard. The
selection will change to OFF, and the BILINX data will be
disabled.
2.
Press IRIS to SAVE and EXIT.
NOTE: For more information on how BILINX may be used to
configure the camera, refer to the Configuration Tool software.
P/N VP-CFGSFT.
Page 16 of 40
EN
SECTION 7
ALARMS
7.1
Inputs
There are four (4) Alarm Inputs that may be activated by a dry
contact input closure. The alarm conditions must be present for
greater than 200 ms to be recognized as a valid alarm. Each
alarm input may be individually programmed for the type and
desired Action to occur when an alarm is received (as shown in
FIGURE 7A). The choices available are listed in FIGURE 12F in
the back of this manual, and are explained in the Advanced
Menu, SECTION 12.
Section 7
The OSD may be turned OFF, and then the camera will move to
the shot, but will not flash the word ALARM. To acknowledge
an ALARM and turn off the flashing display, use the auxiliary
command OFF-65-ENTER on a Bosch controller/keyboard. The
ALARM message will be removed from the monitor, but if the
contact closure is still activated, an "A" will appear in the top
right-hand corner of the monitor, as shown in PHOTO 7B.
When the contact input changes back to a non-alarm state, the
"A" will be removed.
Photo 7B Alarm Acknowledged but still active
Figure 7A Input Setup Menu
The most important actions are GO TO SHOT and the OSD
display. The camera may be programmed to go to any
preprogrammed shot from 0 to 99. If 0 is entered as the SHOT
number, the camera simply flashes the word ALARM on the
monitor, but will not move from the current position (see
PHOTO 7A).
7.2
Low Pressure Alarm
The pressurized version of the AutoDome has an internal lowpressure sensor that is prewired to Alarm Input # 4. If the internal pressure is lost, the sensor activates the ALARM input, and
instead of the word ALARM being displayed, the word
PRESSURE will flash on the display, as shown in PHOTO 7C.
Photo 7C Low Pressure Alarm
Photo 7A Alarm active
© 2005 Bosch Security Systems
Page 17 of 40
EN
Section 7
When the pressure alarm is acknowledged using
OFF-65-ENTER, the flashing display will stop, but the letter "P"
will appear in the top right-hand corner of the monitor
(PHOTO 7D). This AutoDome will continue to display this
warning until the low-pressure problem has been corrected.
Low Pressure
Photo 7D Low Pressure Alarm continued
7.3
Alarm Relay Output
The alarm relay output may be activated either manually, or
triggered when an Alarm occurs. There are three possible
choices for the time period that the relay output will remain
activated. These choices are:
1
Follow input: This means it mimics the state of the alarm.
As long as the alarm is active, the relay will be energized.
2
Latched: The relay will energize upon an alarm, and will
remain energized until the user issues the command
OFF-65-ENTER twice. The first time acknowledges the
alarm and removes the OSD (if programmed to display),
and the second time clears the alarm and resets the relay.
3
Specific length of time. This can be anywhere from
one sec to ten min. An OFF-65-ENTER that's entered
twice will again deactivate the relay, even if the timer has
not yet expired.
The function of OFF–65-ENTER is different when the trigger
for the relay output is an alarm input. When the alarm input is
activated, the relay output will also be activated immediately.
When the alarm is acknowledged by OFF-65-ENTER, the first
time, the relay output will NOT deactivate. It will remain on for
the period selected in the menu. However, if OFF-65-ENTER is
entered a second time, the relay output will deactivate immediately, no matter what time period is set in the menu. This acts as
an alarm override, but the relay output will not activate again
until the Alarm has been cleared and another alarm occurs.
Example: Alarm 1 is set to be NORMALLY OPEN,
GO TO SHOT 1, OSD ON, and the output is set to be
triggered by Input 1 for a time period of 1 min, and is
connected to the Alarm Input of a digital recorder (DVR).
When the external contact is closed, the AutoDome will move
to SHOT 1, flash the word ALARM on the display, and activate
the relay output so the digital recorder starts recording. Pressing
OFF-65-ENTER would clear the flashing display and change to
the letter "A" in the upper right-hand corner, but the relay output will still be on and the DVR still recording. After 30 sec, the
alarm input is still active, but if OFF-65-ENTER is pressed
again, the relay output will turn off and the DVR will stop
recording. The "A" is displayed until the alarm contact changes
state.
These choices are also listed in the Advanced Menu,
SECTION 12.
To manually activate the relay output from a Bosch
controller/keyboard, use the sequence of ON-65-ENTER. Use
OFF-65-ENTER to deactivate it.
© 2005 Bosch Security Systems
Page 18 of 40
EN
SECTION 8
AutoTrack
WHAT IS AutoTrack?
The AutoTrack feature is a motion detector, which takes over
PTZ control of the Dome. The user always has the ability to
manually override by simply moving the joystick. It is sensitive
to motion of all kinds, and should only be used in the same
applications that a standard motion detector would be; anywhere there is little or no motion expected. It may be used in
conjunction with a preset tour, or a recorded guard tour that
takes periodical pauses of at least two sec during the tour. It can
also be used when the dome is static (stationary in one position).
Section 8
The AUTOTRACK COMMS setting will default appropriately,
based on the presence of an AutoTracker. This setting should
not need to be adjusted unless there is a malfunctioning
AutoTracker unit, that presents an objectionable error message
on the OSD.
The User command for turning AutoTrack on and off is
ON/OFF-78-ENTER.
The AutoTracker has an output relay, which can be wired to an
alarm system, or to a recorder. This relay is energized whenever
the AutoTracker is actively tracking an object (when
is
flashing).
AutoTracker symbol
When the AutoTracker is on, it actively looks for motion. When
in this state, the OSD shows the
symbol in the upper lefthand corner of the screen (see PHOTO 8A). Once motion is
detected, the
begins to flash, and AutoTracker will control
the PTZ of the dome. It will attempt to follow the motion,
depending on the target’s speed, size, and distance. Once
motion is no longer detected, it will zoom out, in an attempt to
re-acquire the target. If not successful, it will stop tracking.
What happens next depends on the Iinactivity settings of the
dome. If Inactivity is set to return to Shot one, once
AutoTracker gives up, the dome will return to Shot one.
Similarly, if Inactivity is programmed to return to previous aux,
the dome will do that as well.
The AutoTracker itself also reacts to the Inactivity setting; when
the AutoTracker is on, and a user takes manual control of the
camera, AutoTracker turns off. AutoTracker will remain off
unless Inactivity is turned on, in which case AutoTracker will
turn itself back on after the Inactivity time period expires.
Photo 8A AutoTracker symbol
NOTE: The Pressurized housing cannot be used with the
AutoTracker.
Programming AutoTrack is simple. It should be completely wired
to the dome before the dome is powered. If connected properly,
the dome will recognize the AutoTracker, and its features will be
visible throughout the AutoDome OSD menus. The only installation setting needed is in the PTZ menu under the heading
CAMERA HEIGHT. This should be set to the approximate
height of the camera from the floor of the area where targets are
to be monitored. This allows AutoTracker to adjust the zoom to
the optimal settings while tracking. The minimum camera height
is eight ft, and the maximum is 100 ft, though performance may
vary at the extremes.
© 2005 Bosch Security Systems
Page 19 of 40
EN
SECTION 9
PELCO PROTOCOL MODE
9.1
Description
The Pelco Protocol Mode provides support for Pelco-P and
Pelco-D protocols, and is incorporated in AutoDome firmware
version 5.31 and higher. It features Auto Baud Detection which
automatically detects and adjusts the AutoDome protocol and
baud rate to match the controller’s.
9.2
Hardware Configuration
9.3 RS-485 Setup
To use the Pelco Protocol Mode, the AutoDome must be
configured for RS-485 operation.
1.
2.
3.
Section 9
9.5 Software
AutoDome firmware 5.31 or higher must be installed for Pelco protocol mode to operate. Procedures for uploading a new AutoDome
firmware must be followed to successfully install an upgrade.
Only a Bosch VP-CFGSFT firmware upload tool (sold
seperately) can be used to install a firmware upgrade to
the AutoDome.
9.6 Commands
The Pelco Set-Preset command is used by AutoDome to set
Presets 1 through 99. Some Presets have special meaning and
override the normal preset function as follow:
Special Preset Commands
SET A PRESET
To set a Preset press and hold the
[PRESET] button for 2 seconds.
Set the AutoDome configuration dipswitch #2 to ON. See
SECTION 1 and SECTION 2.
92-PRESET
Sets the Left Pan limit for an AutoScan
with Limit Stops enabled.
Connect the RS-422 controller Tx+ terminal to the
AutoDome’s RxD terminal.
93-PRESET
Sets the Right Pan limit for an AutoScan
with Limit Stops enabled.
Connect the controller’s Tx- terminal to the AutoDome’s
TxD terminal. See SECTION 1 and SECTION 2.
95-PRESET
Invokes the Setup Menu.
GO TO A PRESET
To go to a Preset momentarily press and
release the [PRESET] button.
33-PRESET
Pans the AutoDome 180 degrees (Flip).
34-PRESET
Goes to Zero Pan.
Both the Pelco controller and AutoDome must be configured
before connecting the devices together. The AutoDome will
respond to Bosch OSRD, Pelco-D, and Pelco-P commands.
The Pelco Mode only supports RS-485 protocol. It
will not transmit reponses to commands it receives.
9.4
•
Set Addresses
Addresses 0 to 9998 are available for Bosch OSRD
commands.
94-PRESET
Initiates a Preset Tour
96-PRESET
Stops a scan.
•
An AutoDome with an address set to 0 will respond to
commands sent to any address.
97-PRESET
Initiates FastAddress (Pelco Random
Scan)
•
Pelco-P protocol must use addresses 1-to-32.
98-PRESET
•
Pelco-D protocol must use addresses 1-to-254.
Toggles the Sync Mode between Line
Lock and Crystal (Pelco Frame Scan).
This command is only accessible for
2 minutes after power is applied and
then reverts to normal Preset
functionality.
99-PRESET
Start an AutoScan. (User can enable or
disable Limit Stops in the Setup Menu
for AutoScan.)
An AutoDome that was previously configured with an
address above 32 (Pelco-P upper limit) or 254 (Pelco-D
upper limit) can be used without re-addressing the
unit. However, care must be taken that no two
addresses are repeated.
For example:
Pelco-P addresses above 32 are repeated in multiples of
32 (1, 33, 65, 97 are the same).
Pelco-D address above 254 are repeated in multiples of
254 (1, 255, 509, 763 are the same).
© 2005 Bosch Security Systems
Some Pelco controllers do not support all Preset
numbers. Consult the specific Pelco controller’s
documentation for supported Presets.
Page 20 of 40
EN
Section 9
Bosch Menu…
(Locked) Accesses the full AutoDome configuration menu and all AutoDome settings.
Command Lock:
(Locked) Allows/Disallows (ON/OFF)
locked commands to be accessed.
Edit Password:
(Locked) Sets or displays password. See
Auto Dome Security, SECTION 4 for
details. (Must enter password to unlock
menu even if set to 0000 or 9999.)
FastAddress…
(Locked) Sets/changes the dome address
using the keyboard and on-screen menus.
Limit Stops:
(Unlocked) Enabled determines if an Auto
Scan (99-PRESET) scans between left and
right limits. Disabled will scan continuous
360°.
Edit Tour…
(Unlocked) Presets can be
removed/restored (On/Off) from the Preset
tour, via an on-screen menu. Presets can
still be displayed manually.
Edit Presets…
(Unlocked) Permits modification of Preset
scenes from an on-screen menu (recommended).
White Balance:
(Locked) Default setting when controller’s
white balance is off.
Scan Speed:
9.10 Preset Tour
The AutoDome can be programmed to execute a Preset Tour
with adjustable dwell times. To start a tour, the Pattern 3
command must be sent from the Pelco controller by entering
3-[PATTERN]. Consult the specific Pelco controller’s
documentation for information on setting Patterns.
(Unlocked) On-screen menu allows the
setting of the AutoPan and AutoScan
speeds. Default is 30 degrees/second.
Stabilization:
(Unlocked) Enables/disables stabilization
mode. Only available with some cameras.
Tour Period:
Dwell time can be adjusted by entering 95-[PRESET] to enter
the main Setup Menu and then selecting the Tour Period menu
item. Presets to include on a tour can also be added or deleted
through the Edit Tour menu item.
(Unlocked) On-screen menu changes the
length of waiting time between presets.
Recordings:
(Unlocked) Used to select record Pattern 1
or 2, if normal pattern command does not
respond.
Night Mode:
(Unlocked) Switches from color to
monochrome (Day/Night models only).
AutoPivot:
(Locked) Allows a subject to be followed
while beneath the camera, without inverting
the picture. Default is ON.
9.7 Menu
To access the dome’s main Setup Menu enter 95-[PRESET].
AutoDome will display a list of configuration items. Some
menu items can be locked and require a system password to
access. The Bosch Menu item provides full access to the
AutoDome menus.
9.8 Preset Titles
Preset titles can be added, removed, or changed through the
main Setup Menu through the Edit Presets menu item.
Some Pelco preset titles can be 20 characters long;
however AutoDome only supports 16 characters and
will drop the last 4.
9.9 Patterns
Pelco Patterns or recordings are supported. The AutoDome
supports patterns 1 and 2.
1.
To start recording a Pattern, enter #[PATTERN] where
the number specifies which of the 2 supported patterns
to record.
2.
The command to stop a pattern varies among different
Pelco controllers. Consult the specific Pelco controller’s
documentation for information on setting Patterns.
3.
To playback a recorded Pattern, select the desired pattern
number and momentarily press (do not hold) the
[PATTERN] key. The user can stop the playback by
sending any PTZ, focus, or iris command.
9.11 95-PRESET Menu
When a 95-[PRESET] command is sent from a Pelco control
device, the AutoDome displays the main Setup Menu.
Following are the menu items and a brief description:
Software Version…(Unlocked) Briefly displays the camera
software versions.
Restore Factory Defaults…
(Locked) Restores factory defaults.
© 2005 Bosch Security Systems
Page 21 of 40
EN
9.12
Special Considerations
Refer to the controller’s user manual
To get the best results with using a specific feature, refer to the
Pelco controller’s user manual.
Auto Baud Detection Feature
Baud rate and protocol are automatically detected and adjusted
by AutoDome whenever the controller starts transmitting. No
manual adjustments are required.
Because of the slow command repeat rate of the DX8000, Auto
Baud Detection is slow. The fastest way to change the baud rate
is to enter the Setup Menu, and select Bosch Menu>
Communication Setup> Baud Rate and select the desired baud
rate for the AutoDome. Then change the baud rate of the
controller and operate the Pan/Tilt to gain control of the
AutoDome at the controller’s baud rate.
If it is not possible to access the AutoDome’s Setup Menu at the
present baud rate (i.e. the baud rates of the controller source
and the AutoDome are mismatched), then the Auto Baud
Detection feature can be initiated by rapidly repeating PTZ
movements or focus/iris commands for several seconds which
causes the AutoDome to lock onto the controller’s baud rate
and protocol. This can take up to 60 seconds or more
depending on the difference between the two baud rates.
Section 9
For example: When the CM6700 matrix switch sends a
Set-Preset command to the AutoDome it will display
instructions on the monitor for entering setting the title and
completing the Preset. The operator must use the [F1] and [F2]
keys, along with panning left and right, to set a Preset title. The
operator must tilt the joy stick down to the SET option on the
monitor until it starts blinking. Then the operator must pan
right or press the [ACK] button to finish setting the Preset.
Refer to the CM6700 controller user manual.
Custom Control Software
Most custom control software that adheres to Pelco-D and
Pelco-P protocol specifications will operate with the AutoDome
Pelco Protocol Mode. However, custom control software that
requires a response from the AutoDome will not operate
because of the simplex receive requirements.
Some commands that trigger the AutoDome to solicit user
input can also cause a problem for scripts run by the custom
control software. For example, the Reset Camera to Defaults
command requires the user to confirm their intent to reset the
camera defaults.
DX8000 Digital Video Recorder [SET] button
The DX8000 GUI uses the [SET] button to toggle the function
of the [PRESET] button. While the [SET] button is activated
(indicator is lit) the [PRESET] button is used to issue the
Set-Preset commands. This command is used to set a preset
shot or to activate the special preset functions as described in
Section 9.6: Commands.
While the [SET] button is deactivated, the [PRESET] button
is used to issue the Go-to-Preset command. This command is
used to move the AutoDome to a previously defined preset
position. This command is also used to activate special preset
functions as described in Section 9.6: Commands.
CM6700 Matrix Switch Presets
The AutoDome must be connected to the RS-422 Tx+/terminal connections to COM1 of a CM6700 matrix switch.
The CM6700 configuration introduces behavior that differs
from that of a direct keyboard or the DX8000 DVR
configuration.
© 2005 Bosch Security Systems
Page 22 of 40
EN
Section 10
SECTION 10
MAINTENANCE/COMPONENT
REPLACEMENT
No special maintenance is required.
Occasionally, dust may accumulate inside the housing and coat
the transparent dome/trim ring. In this case, power the unit off
and remove the dome so that it is away from the camera. While
using proper eye protection, clean the dome with clean compressed air from a spray can and microwave-safe paper towels,
then reseat the dome.
In instances of high humidity, the EnviroDome may require a
replacement desiccant bag. To order, contact Bosch and specify
part number 303 3804 003.
Service Centers
U.S.A.: Phone: 800-366-2283 or 408-956-3895
fax:
800-366-1329 or 408-956-3896
e-mail: NationalServiceCenter@ca.slr.com
Canada:
514-738-2434
Europe, Middle East & Asia Pacific Region:
32-1-440-0711
For additional information, see
www.boschsecurity.com.
© 2005 Bosch Security Systems
Page 23 of 40
EN
Section 11
SECTION 11
TROUBLESHOOTING GUIDE
Problem
Solution
NO VIDEO
•
Ensure that the AutoDome is powered, and all cables are properly connected.
•
Ensure that the address is properly set.
•
Ensure that the biphase or RS-232 is connected.
•
Ensure that other cameras can be controlled; if not, check the control system.
•
Ensure that the address is set. If an address is set to 0000, it responds to commands
for any address.
•
Ensure that GAIN CONTROL is set to AUTO (ON-43-ENTER).
•
Ensure that Iris level has not changed; if so, adjust the IRIS control on the
keyboard. To permanently adjust, use ON-11-ENTER.
•
Verify proper termination.
•
Unlock commands (OFF-90-ENTER; may require password).
NOTE: Commands automatically lock 30 min after being unlocked.
NO CAMERA CONTROL
CAMERA MOVES WHEN
MOVING OTHER CAMERAS
PICTURE DARK
CANNOT ACCESS USER
SETTINGS
1. Try resetting factory defaults (ON-40-ENTER).
2. Position camera so the entire view is white (white wall).
COLORS ARE NOT CORRECT
3. Enter the White Balance menu (ON-30-ENTER). Move the joystick until one push
W.G. is selected. Wait 10 sec. Press IRIS to return.
4. If this does not work, restore factory defaults (SET-899-ENTER). Note that this
erases all presets and settings.
PERIODIC LOSS OF CONTROL
BACKGROUND IS TOO BRIGHT
TO SEE SUBJECT
PICTURE IS ROLLING, NOISY, OR
DISTORTED
© 2005 Bosch Security Systems
•
Verify that a 110 Ω resistor is across the +/– biphase code terminals at the last
dome in a daisy chain configuration.
•
Turn on backlight compensation (ON-20-ENTER).
•
Electronic AC power line noise may distort the picture and cause loss of Sync.
If the picture is distorted, try switching to Internal Crystal (OFF-42-ENTER).
If this corrects the picture problems, there may be excessive line noise on the
power supply.
Page 24 of 40
EN
Section 11
Problem
Solution
DAY/NIGHT CAMERA DOES
NOT AUTOMATICALLY SWITCH
WHEN IMAGE IS DARK
•
Set GAIN CONTROL to AUTO to enable this feature.
•
If the lower housing is equipped with a desiccant bag, it may need to be replaced
(Bosch part #303 3804 003).
MOISTURE/DAMPNESS ON THE
INSIDE OF THE BUBBLE OF THE
ENVIRODOME
AutoTracker Errors
AN E4 OR E5 IS DISPLAYED IN
THE UPPER LEFT-HAND SIDE
MISSING SOME MENU
SELECTIONS
© 2005 Bosch Security Systems
•
The AutoTracker is being used, and communications between the
AutoDome and AutoTracker have been lost.
•
This is usually due to a wiring error. Check the RS-232 wiring to verify that
RXD, TXD and GROUND are all properly connected.
•
The maximum distance between the AutoTracker and AutoDome is 50 ft.
•
The AutoTrack option communicates at the default baud rate of 19,200, but
if an E5 error occurs, confirm that the baud rate in the Communication
Setup menu is 19,200.
•
Menu selections specific to the AutoTrack appear only if the AutoTrack
option is present.
•
Some features have been added with new firmware revisions.
•
To confirm the firmware version on the monitor, use ON-66-ENTER.
•
Contact Bosch Technical Support for the most current firmware version
available.
•
If the AutoDome is version 5.00 or higher, and the missing menu option
requires an upgrade, purchase the Flash Upgrade kit, P/N G3-UPGRADE-5.
Page 25 of 40
EN
Section 12
SECTION 12
AUTODOME LOCKED COMMANDS
CAMERA
PTZ
GENERAL
SETUP
Access to the AutoDome may be password-protected. See SECTION 4, AutoDome Security for details. To use Locked Commands, first unlock
the AutoDome via OFF-90-ENTER. All locked settings, except FastAddress, can then be changed via ON-46-ENTER. Disallow these commands via
ON-90-ENTER.
Commands
Keystrokes
Description
FastAddress
On-999-Enter
Sets/changes the dome address using the keyboard and on-screen menus. (for cameras not already configured).
On-998-Enter
Sets/changes the dome address using the keyboard and on-screen menus. (for all cameras, even those already configured).
Display FastAddress On-997-Enter
Briefly displays all dome addresses.
Auto Iris
On/Off-3-Enter
Camera (Iris) adjusts automatically/manually (On/Off) to light conditions.
Auto Focus
On/Off-4-Enter
Camera automatically/manually (On/Off) focuses.
Gain Control
On/Off-43-Enter
Turns gain control to Automatic or Off. When in Automatic mode, the gain increases to compensate for darker scenes.
On-screen Display
On/Off-60-Enter
Turns On/Off the On-screen Display. When off, there is no On-screen feedback.
On-screen
Display Adjust
On/Off-61-Enter
Changes the characters and position of the display.
On-screen instructions are provided.
Newer versions of the Receiver/Driver, in combination with firmware version 5.10 or higher, allow the brightness to be
adjusted. The firmware automatically detects whether the Receiver/Driver supports this, and displays the selection when
available.
Sector Title Edit
On/Off-63-Enter
Edits the current Sector name. On-screen instructions are provided.
Sector Blanking
On-86-Enter
Masks video from being displayed in selected sectors.
Privacy Masking
On-87-Enter
Masks video from being displayed in selected zones.
Bypass All
Masks/Blanking
Off-86-Enter
or Off-87-Enter
Removes all viewing restrictions imposed by sector blanking/privacy masking but keeps their locations in memory.
On-86/87-Enter reactivates all masks/blanking.
Lock/Unlock
Commands
On/Off-90-Enter
Allows/Disallows Locked Commands to be accessed.
Password
Set-802-Enter
Sets or displays password. See AutoDome Security, SECTION 4 for details.
Factory Home
Position
Set-110-Enter
SET recalibrates camera and returns it to home position.
Restore Defaults
On-40-Enter
Restores Factory Defaults.
Left Limit
Set-101-Enter
Sets the current position as the left limit of Auto Pan. Default is 0 degrees.
Right Limit
Set-102-Enter
Sets the current position as the right limit of Auto Pan. Default is 359.9 degrees.
Inactivity
On/Off-9-Enter
Selects the mode that the dome reverts to after a duration without operator activity. Default is OFF.
Preset
Tour Period
On/Off-15-Enter
Increase/Decrease (On/Off) the time between Presets during Preset Tour.
AutoPivot
On/Off-18-Enter
Allows a subject to be followed while beneath the camera, without inverting the picture. Default is ON.
AutoTrack Comms
On/Off-77-Enter
Enables/Disables the Tracker. When disabled, no status will be displayed. Since this is not retained in non-volatile memory, if
the AutoDome receives Tracker messages on start-up, the Tracker will be enabled again (AutoTracker option ONLY).
Camera Height
On/Off-79-Enter
Selects the height of the camera in respect to the surface being monitored with the AutoTracker feature
(AutoTracker option ONLY).
Select
White Balance
On/Off-35-Enter
or On/Off-30-Enter
Adjusts camera color (white balance) for specific settings.
Sharpness
On/Off-44-Enter
Picture (vertical aperture) sharpens/softens.
Iris Adjust
On/Off-11-Enter
Edits the Auto Iris level.
Shutter
On/Off-23-Enter
(Frame Integration)
Sliding scale from 1 second to 1/10,000 sec,
with Auto Slow Shutter at extreme left.
Sync Mode
On/Off-42-Enter
Sets camera sync for external-line/internal-crystal (On/Off).
Adjust Line
Lock Phase
On/Off-41-Enter
Changes the phase delay of the camera when in
external line lock mode.
Switch Polarity
On-91-Enter
Switches the polarity of the Zoom, Focus, and Iris controls.
Digital Zoom
On/Off-80-Enter
Enables (On) or disables (Off) the digital zoom.
Night Threshold Adj. On-58-Enter
Selects the video level at which the camera switches to night mode (Day/Night only).
QuickSet Select
Allows mode selection where multiple camera settings are set according to the chart below (Day/Night only).
QuickSet Mode Name
Low Light Color
Full Auto w/ Slow Shutter
Full Auto w/o Slow Shutter
Night w/ Slow Shutter
Night w/o Slow Shutter
On-59-Enter
Gain Control
Auto
Auto
Auto
Auto
Auto
© 2005 Bosch Security Systems
IRIS
Auto
Auto
Auto
Auto
Auto
Slow Shutter
Auto
Auto
1/60
Auto
1/60
IR Filter
In
Auto
Auto
Out
Out
Page 26 of 40
EN
Section 13
SECTION 13
ADVANCED MENU
Main Menu
Depending on the AutoDome password security set for
your system, a password may be required to access the ADVANCED
MENU. This enhanced software makes programming and customizing the AutoDome easy. All settings are editable via the Main Menu.
Press ON-46-ENTER to enter the Main Menu. If no menu is
displayed, the system may be locked. To unlock the AutoDome, press
OFF-90-ENTER, and follow the on-screen commands to edit the settings. As indicated at the bottom of the screen, use IRIS to SAVE and
EXIT or to RETURN to a previous menu.
CAMERA SETUP
(See FIGURE 13A for CAMERA SETUP menu hierarchy).
White Balance – This camera function maintains proper color reproduction as the color temperature of the scene changes
(i.e. daylight, flourescent). The Factory Default setting is AUTOMATIC.
Choices:
Extended Auto WB . . . .Camera adjusts color using extended range.
*Automatic WB . . . . . . . .Camera constantly adjusts the color.
Indoor WB . . . . . . . . . . .Camera optimizes color for typical indoor conditions.
Outdoor WB . . . . . . . . . .Camera optimizes color for typical outdoor conditions.
One Push WB . . . . . . . .Sets the camera’s color settings for the current scene. Zoom on a well lit, white object
(i.e. a white wall or paper) before activating.
Gain Control – Electronically brightens darker scenes which may cause graininess in low light scenes. The Factory Default
setting is AUTO.
Choices:
Off . . . . . . . . . . . . . . . . . . .Camera uses only the IRIS to adjust to low light.
*Auto . . . . . . . . . . . . . . . . .Camera adds electronic gain based on lighting conditions.
Max Gain Level – Adjusts the maximum gain level that Gain control will adjust to when set to AUTO.
Choices: . . . . . . . . . . . . . .Sliding Scale from 1 to 6 (in 4 dB gain steps).
Sharpness – Adjusts the sharpness/detail of the picture. The Factory Default setting is six on the sliding scale of
about 16.
Choices: . . . . . . . . . . . . . .Sliding Scale from –(soft) to +(sharp).
Synch Mode – Sets the synch mode of the camera. The Factory Default setting is LINE LOCK.
Choices:
Crystal . . . . . . . . . . . . . . . . .Camera is synchronized to an internal crystal (recommended if there is noise on the power line).
*Line Lock . . . . . . . . . . . .Camera is synchronized to AC power. This eliminates picture roll in multicamera systems.
Line Lock Delay – Optimizes LINE LOCK mode to eliminate picture roll in multiphase power applications. The Factory
Default setting is zero.
Choices: . . . . . . . . . . . . . .Sliding Scale (–0° to 359°).
Backlight Compensation – Improves the image quality when the background has a high level of illumination.
Choices: . . . . . . . . . . . . . .On, Off.
Shutter – Sliding scale from 1 sec to 1/10,000 sec, with Auto Slow Shutter at extreme left.
Restore Defaults – Restores ALL choices, for this submenu ONLY, back to the Factory Defaults.
Choices: . . . . . . . . . . . . . .Yes, No.
© 2005 Bosch Security Systems
Page 27 of 40
EN
Section 13
NOTE: The following four (4) CAMERA SETUP options pertain to Day/Night models only, and will not appear on the screen
otherwise.
Night Mode – Selects night mode (B/W) operation (Day/Night models only).
Choices: . . . . . . . . . . . . . .On, Off, Auto.
Night Mode Threshold – Adjusts the level of light at which the camera automatically switches to night mode (B/W)
operation (Day/Night models only).
Choices: . . . . . . . . . . . . . .Sliding Scale from 10 to 55 (in increments of five).
Night Mode Color – Determines if color processing remains in effect while in night mode (Day/Night models only).
Choices:
On . . . . . . . . . . . . . . . . . .Color burst remains in video signal. Picture has a greenish shade of B/W.
*Off . . . . . . . . . . . . . . . . . . . .Video is true B/W without color burst in video signal.
QuickSet Mode – Selects one of several modes where camera settings are set according to the preceding AUTODOME
LOCKED COMMANDS chart in SECTION 12 (Day/Night models only).
LENS SETUP
(See FIGURE 13B for LENS SETUP menu hierarchy).
Auto Focus – AutoDome automatically focuses on the subject in the center of the screen. The Factory Default setting is
SPOT.
Choices:
Constant . . . . . . . . . . . . .Auto Focus is always active, even while moving.
Manual . . . . . . . . . . . . . . . . .Auto Focus is inactive; manual focus must be used.
*Spot . . . . . . . . . . . . . . . . .Auto Focus activates after the camera stops movement. Once focused, Auto Focus is inactive
until the camera is moved again.
Auto Iris – AutoDome automatically adjusts to varying light conditions. The Factory Default setting is CONSTANT.
Choices:
*Constant . . . . . . . . . . . . .Auto Iris is constantly active.
Manual . . . . . . . . . . . . . .Iris must be manually adjusted.
Auto Iris Level – Reduces the camera’s Iris reference level for proper exposure.
Choices: . . . . . . . . . . . . . .Sliding scale from – (reduce brightness) to + (increase brightness).
Focus Speed – Adjusts the manual focus speed. The Factory Default setting is two.
Choices: . . . . . . . . . . . . . .Sliding Scale from 1 (normal) to 8 (fast).
Iris Speed – Adjusts the manual iris speed. The Factory Default setting is five.
Choices: . . . . . . . . . . . . . .Sliding Scale from 1 (normal) to 10 (fast).
Max Zoom Speed – Adjusts the manual zoom speed. The Factory Default setting is FAST.
Choices: . . . . . . . . . . . . . .Fast*, Medium, and Slow.
Digital Zoom – Enables digital zoom. The Factory Default setting is ON.
Choices:
*On . . . . . . . . . . . . . . . . . .When the camera reaches maximum optical zoom, the image is electronically zoomed (up to 12X).
Off . . . . . . . . . . . . . . . . . .When the camera reaches maximum optical zoom, it does not electronically zoom.
Restore Defaults – Restores ALL of the choices, for this submenu ONLY, back to the Factory Defaults.
Choices: . . . . . . . . . . . . . .Yes, No.
© 2005 Bosch Security Systems
Page 28 of 40
EN
Section 13
PTZ SETUP
(See FIGURE 13C for the PTZ SETUP menu hierarchy).
Autopan Speed – Adjusts speed of the camera during Auto Pan/ Auto Scan. The Factory Default setting is 30°/sec.
Choices: . . . . . . . . . . . . . .Sliding Scale from 1°/sec to 60°/sec.
Tour Period – Changes dwell time between Presets during a Preset Tour. The Factory Default setting is five sec.
Choices: . . . . . . . . . . . . . .Sliding Scale from 3 sec to 10 min.
PTZ Fixed Speed – Sets Pan/Tilt speed when controlled by a fixed speed controller. The Factory Default setting is four.
Choices: . . . . . . . . . . . . . .Sliding Scale from 1 (slow) to 15 (fast).
Inactivity – Selects the mode that the dome reverts to after the period of time specified in the Inactivity Period (next menu
option), without operator activity. The Factory Default setting is OFF.
Choices:
*Off . . . . . . . . . . . . . . . . . .Remains on current scene indefinitely.
Scene 1 . . . . . . . . . . . . .Returns to Preset 1.
Prev Aux . . . . . . . . . . . . .Returns to previous activity (previous activities include Aux commands 1, 2, 8, 50, 52).
Inactivity Period – The time period of inactivity before the above action occurs. Default setting is two min.
Choices: . . . . . . . . . . . . . .Sliding Scale from 3 sec to 10 min.
AutoPivot – AutoPivot automatically rotates the camera 180° when following a subject travelling directly beneath the camera.
The Factory Default setting is ON.
Choices:
*On . . . . . . . . . . . . . . . . . .Camera automatically pivots.
Off . . . . . . . . . . . . . . . . . .Camera stops tilting when looking straight down.
Restore Defaults – Use this to restore ALL choices for this submenu ONLY, back to the Factory Defaults.
Choices: . . . . . . . . . . . . . .Yes, No.
NOTE: The following two (2) PTZ SETUP options refer to AutoTrack models only, and will not appear on the screen otherwise.
AutoTrack Comms: – Enables/Disables the AutoTracker completely, including all communications.
Choices: . . . . . . . . . . . . .On (enable), Off (disable).
Camera Height: – Selects the height of the camera in relation to the surface being viewed.
Choices: . . . . . . . . . . . . .From 2.4 m to 30.7 m (8 ft to 100 ft); use the Joystick Up/Down to adjust.
DISPLAY SETUP
(See FIGURE 13D for DISPLAY SETUP menu hierarchy.)
Title OSD – Controls whether sector or shot title are displayed. The Factory Default setting is MOMENTARY.
Choices:
*Momentary . . . . . . . . . . .Titles are displayed for a few sec, then disappear from the screen.
On . . . . . . . . . . . . . . . . . . .Titles are displayed.
Off . . . . . . . . . . . . . . . . . . .Titles are hidden.
Camera OSD – Controls whether the camera information is displayed (such as digital zoom, Iris OPEN/close, etc.).
The Factory Default is ON.
Choices:
*On . . . . . . . . . . . . . . . . .Camera commands are displayed.
Off . . . . . . . . . . . . . . . . . . .Camera commands are hidden.
Display Adjust – Adjusts the vertical position of the on-screen display. See the on-screen display for instructions.
Sector Blanking – Selects sectors for video blanking. Sectors available are 1 to 16. See the on-screen display for
instructions.
Privacy Masking – Up to six (6) privacy masks are available to mask out sensitive areas.
Restore Defaults – Restores ALL choices for this submenu ONLY, back to the Factory Defaults.
Choices: . . . . . . . . . . . . . .Yes, No.
© 2005 Bosch Security Systems
Page 29 of 40
EN
Section 13
COMMUNICATION SETUP
(See FIGURE 13E for COMMUNICATION SETUP hierarchy).
Baud Rate – Controls baud rate for AutoDome communication in the Normal mode. Factory Default is 9600.
Choices: . . . . . . . . . . . . .9600*, 19200, 38400, 57600.
Bilinx - Enables/Disables the Bilinx communications directly through the coax. Factory Default is ON.
Choices: ..............On*, Off.
Restore Defaults – Restores ALL choices for this submenu ONLY, back to the Factory Defaults.
Choices: . . . . . . . . . . . . . .Yes, No.
ALARM SETUP
(See FIGURE 13F for ALARM SETUP hierarchy).
Input 1 thru 4 – Contains a submenu of choices for Input type, and the action to occur when the alarm is activated.
Alarm 1 through 4
Input – Controls the input type that the camera will be expecting. Factory Default is OFF.
Choices: . . . . . . . .OFF*, Normally Open (N.O.), Normally Closed (N.C.).
Action – There are three standard choices to determine how the AutoDome will respond when an alarm input is
activated, and one additional choice that will appear ONLY when the AutoTracker is being used.
Go to Shot – The AutoDome moves to the pre-position (shot) selected. Default is the input number.
Choices: . . . . .0 to 99.
NOTE: If 0 is selected and OSD is set to YES, the camera will not move, but will display a flashing ALARM
prompt.
OSD – Controls whether a visual ALARM prompt will be displayed. Default is YES.
Choices: . . . . .Yes*, No.
Transmit – Controls whether an alarm message will be transmitted via RS-232/RS-485. Default is NO.
Choices: . . . . .Yes, No*.
Track – Controls whether AutoTrack should be activated when an alarm occurs. Displayed on AutoTrack models
ONLY.
Choices: . . . .Yes, No.
AutoTrack / Relay Output – Contains a submenu of choices that control how the relay output will function.
Period – Controls the time period that the relay output will remain activated. Default is FOLLOW INPUT.
Choices:
FOLLOW INPUT* – The relay output will remain activated as long as the alarm input is active.
LATCHED – The relay output will latch ON and remain activated until an OFF-65 command is sent twice. The
first OFF-65 command clears the alarm OSD from the display; the second OFF-65 command
deactivates the output.
SLIDING SCALE – from 1 sec to 10 min. The relay output remains activated for the selected time period.
Trigger By: Select which alarm input will cause the relay output to Activate. Trigger By applies to Relay Output only,
not AutoTrack.
Choices: ..........Input 1 through 4: Yes, No.
Alarm Status – Displays the states of the Alarm inputs and the relay output. This is an active display, that changes
as the Alarm Status changes. It is informational only.
Restore Defaults – Restores ALL choices for this submenu ONLY, back to the Factory Defaults.
Choices: . . . . . . . . . . . . . .Yes, No.
LANGUAGE SETUP
(See FIGURE 13G for LANGUAGE SETUP hierarchy.)
Language – Selects the language to be displayed.
Choices: English, Spanish, French, German, Polish and Portuguese.
© 2005 Bosch Security Systems
Page 30 of 40
EN
Section 13
Sliding Scale
359°
–0°
*default = 0
Sliding Scale
1 sec 1/10,000 sec
Auto Slow Shutter
WHITE
BALANCE
SHUTTER
NIGHT MODE
Sliding
Scale
10 55
NIGHT MODE
THRESHOLD
On
*Off
NIGHT MODE
COLOR
**Day/Night Settings
On
Off
*Auto
Off
GAIN
CONTROL
CAMERA
SETUP
*Auto
Sliding Scale
1
6
*default = 4
MAX GAIN
LEVEL
Sliding Scale
– (soft)
+ (sharp)
*default = 6
(on scale of ~16)
SHARPNESS
Crystal
SYNCH
MODE
QUICKSET
MODE
On
*Off
Extended Auto WB
*Automatic WB
Indoor WB
Outdoor WB
One Push WB
LINE LOCK
DELAY
*Line Lock
BACKLIGHT
COMPENSATION
RESTORE DEFAULTS
Yes
* Factory Default
** For Day/Night Models Only
No
Figure 13A Camera Setup
Sliding Scale
1 (normal)
10 (fast)
*default = 5
*Fast
Medium
Slow
AUTO
FOCUS
Constant
Manual
*Spot
IRIS
SPEED
*Constant
Manual
AUTO
IRIS
MAX ZOOM
SPEED
LENS
SETUP
AUTO IRIS
LEVEL
*On
Off
DIGITAL
ZOOM
FOCUS
SPEED
Sliding Scale
– (reduce brightness)
+ (increase brightness)
Sliding Scale
1 (normal)
8 (fast)
*default = 2
RESTORE DEFAULTS
Yes
No
* Factory Default
Figure 13B Lens Setup
© 2005 Bosch Security Systems
Page 31 of 40
EN
Section 13
*Off
Scene 1
Prev Aux
INACTIVITY
AUTOPAN
SPEED
Sliding Scale
3 sec
10 min
*default = 2 min
INACTIVITY
PERIOD
*On
Off
*On
Off
AUTOPIVOT
**AUTOTRACK COMMS
*3.6 m (12 ft)
adjustable from
2.4 to 30.7 m
(8 to 100 ft)
TOUR
PERIOD
PTZ
SETUP
PTZ FIXED
SPEED
Sliding Scale
1°/sec
60°/sec
*default = 30°/sec
Sliding Scale
3 sec
10 min
*default = 5 sec
Sliding Scale
1 (slow)
15 (fast)
*default = 4
**CAMERA HEIGHT
RESTORE DEFAULTS
Yes
* Factory Default
** AutoTracker ONLY
No
Figure 13C PTZ Setup
AvailableMasks
from1to6
DISPLAY
ADJUST
PRIVACY
MASKING
Changes the characters,
position, or brightness of the
display
DISPLAY
SETUP
AvailableSectors SECTOR
from1to16
BLANKING
*On
Off
TITLE
OSD
CAMERA
OSD
*Momentary
On
Off
RESTORE DEFAULTS
Yes
No
* Factory Default
Figure 13D Display Setup
BAUD RATE
*9600
**19200
38400
COMMUNICATION
SETUP
57600
*On
RESTORE DEFAULTS
BILINX
Off
Yes
No
*Factory Default
** AutoTrack uses 19,200 Baud
Figure 13E Communication Setup
© 2005 Bosch Security Systems
Page 32 of 40
EN
Section 13
*Off
INPUT 1
INPUT 2
INPUT 3
***INPUT 4
Input
N.O. (Normally Open)
N.C. (Normally Closed)
Action
ALARM
SETUP
Go to Shot
0 to 99;
*Default = Input Number
OSD
*Yes, No
Transmit:
*No, Yes
**Track
*No, Yes
RESTORE DEFAULTS
Yes
RELAY
OUTPUT
*Follow Input
Period
No
Latched
Sliding Scale
1 sec to 10 min
Alarm Status
Triggered
by:
Displays the status of the
four Alarm Inputs and the
Relay Output
AutoTrack Output
Input 1
Input 2
Input 3
Input4
Period
*No, Yes
* Follow Input
Latched
Sliding Scale 1 sec to 10 min
*Factory Default
**AutoTracker ONLY
***A pressurized dome uses Alarm Input 4 for the pressure limit switch
Figure 13F Alarm Setup
*English
Spanish
French
German
LANGUAGE
SETUP
Portuguese
Polish
RESTORE DEFAULTS
Yes
No
*Factory Default
Figure 13G Language Setup
© 2005 Bosch Security Systems
Page 33 of 40
EN
Appendix A
APPENDIX A
Power Wiring Guide
AutoDome Power Wiring Connections
Refer to the following diagram to ensure proper wiring of the
AutoDome. If using the ENV-PSU for power, use the
THREE WIRE POWER distances identified below.
WARNING: Failure to correctly wire the power to the
EnviroDome could result in heater malfunction.
NOTE: If using the ENV-PSU with the AutoTracker option, the
RS-232 connections (RXD, TXD, GND) must be used.
The maximum distance for RS-232 communications is 50 ft.
TWO WIRE POWER
THREE WIRE POWER (EnviroDome)
Transformer
Output
24 VAC @
30 VA
Transformer Output
24 VAC @
50 VA
Transformer
Output
24 VAC @
20 VA
FOUR WIRE POWER (EnviroDome)
Transformer
Output
24 VAC @
30 VA
Transformer
Output
24 VAC @
20 VA
24 VAC @ 20 VA
AWG Max. Distance - ft (m) Add Wire
Jumper
18
225 ft (68.58)
16
358 ft (109.12)
14
570 ft (173.74)
C– C+ GND RXD TXD GND H*
Dome Connector
24 VAC
C– C+ GND RXD TXD GND H*
Dome Connector
24 VAC
C– C+ GND RXD TXD GND H*
Neutral
Hot
Hot
AWG Max. Distance - ft (m)
18
150 ft (45.72)
16
239 ft (72.85)
14
380 ft (115.82)
Neutral
FOR EnviroDome
Hot
AWG Max. Distance - ft (m)
18
112 ft (34.14)
16
180 ft (57.91)
14
285 ft (86.87)
Neutral
(UNITS NOT REQUIRING HEATERS):
FOR EnviroDome
Hot
FOR INDOOR UNITS ONLY
Hot
AWG Max. Distance - ft (m)
18
90 ft (27.43)
16
140 ft (42.67)
14
225 ft (68.58)
Neutral
FOR EnviroDome
24 VAC
Dome Connector
*Heater connection for EnviroDome only.
© 2005 Bosch Security Systems
Page 34 of 40
EN
Appendix B
APPENDIX B
Gasket Installation (to meet IP66/NEMA 4X, Dust-tight and Powerful Jetting)
Install Gasket with Lip on Top.
Plate Holds Gasket Securely
Insert 4 Screws
© 2005 Bosch Security Systems
Page 35 of 40
EN
AutoDome® and EnviroDome®
Indoor Pendant
In-ceiling Model
User Manual
Version 5.3
EN
NOTE: Remove this User Manual and supply to user.
Security you can rely on
© 2005 Bosch Security Systems
Page 36 of 40
EN
ON-SCREEN PROGRAMMING
The AutoDome software offers user-friendly, on-screen programming. A few common commands are shown below.
Additional commands are listed at the end of this manual.
Saving a scene (Preset)
The AutoDome allows up to 99 scenes to be saved and recalled
instantly. A saved scene is called a Preset. When a Preset is saved,
the position, zoom, and most camera settings are stored.
User Manual
Preset Tour
Once Presets are stored, the AutoDome can cycle through all Presets
or selected Presets. This is called a Preset tour. To include or remove
presets on a tour, type SET-900-ENTER. This displays the current
Presets, and indicates if they are on the tour. Follow the on-screen
instructions to include/remove Presets from the tour.
Note: Presets removed from the tour can still be accessed
manually).
Type ON-8-ENTER to activate the preset tour. To change the time
duration between presets, type ON-15-ENTER and follow the onscreen instructions.
Figure 1 Preset menu
SET-100-ENTER displays the Preset menu (see FIGURE 1). Menu
options are store, delete, name, or edit. Up to 99 scenes can be
saved, and the system automatically selects the next available
number. When a Preset is saved, it can be named via the joystick,
FOCUS, and IRIS (see FIGURE 2). The name can be up to
16 characters long. This Preset can later be viewed using the
SHOT-#-ENTER command, where # is 1-99.
Figure 3 Preset tour menu
Setting the Preset Tour period
To change the time duration between presets in a Preset Tour, type
ON-15-ENTER, and use the joystick for adjustments
(see FIGURE 4).
Figure 4 Preset tour period adjustments
Figure 2 Naming a scene (Preset)
© 2005 Bosch Security Systems
Page 37 of 40
EN
User Manual
Record/Playback Tours
Two independent macros (series of commands) can be recorded;
A & B. These macros can be several hours in duration, although
tours involving constant commands only last minutes. While
recording, the on-screen display indicates remaining memory (see
FIGURE 5). To begin recording on A, move the camera to the
desired starting point and type ON-100-ENTER. The AutoDome
now records all camera activities, until the recording is ended by
OFF-100-ENTER. Once A has been recorded, B is available via the
ON/OFF-101-ENTER command. Playback can be continuous
(ON-50-ENTER for A; ON-52-ENTER for B) or one shot
(ON-51-ENTER for A; ON-53-ENTER for B).
Figure 5 Recording
Changing AutoPan and AutoScan speeds
The AutoPan and AutoScan speeds (see FIGURE 6) can be
adjusted via ON-14-ENTER. Use the joystick to adjust the speed.
It is helpful for the Pan or Scan to be active when entering
ADJUST mode, to see the speed change.
Figure 6 AutoPan / AutoScan speed adjust
© 2005 Bosch Security Systems
Page 38 of 40
EN
User Manual Commands
AUTODOME USER COMMANDS
PRESET
PTZ
UNLOCKED COMMANDS
Commands
Scan
AutoPan
Preset Menu
Preset Tour
Preset Tour
Period
Preset Save
Preset Call
Edit Preset Title
Edit Preset Tour
ALARM
Modify
Preset Tour
Alarm Clear/
Relay Output
Record A
SETUP
RECORD
Record B
Continuous
Playback A
Playback A
Continuous
Playback B
Playback B
Scan+Auto
Pan Speed
Backlight
Compensation
View Factory
Settings
Software Version
Night Mode
Day/Night Menu
AutoTrack
Keystrokes
ON/OFF-1-ENTER
ON/OFF-2-ENTER
SET-100-ENTER
ON/OFF-8-ENTER
ON/OFF-15-ENTER
Description
Camera continuously pans in the last direction that the joystick was moved. Moving the joystick stops the scan.
Camera continuously pans back and forth between limits. Moving the joystick stops the scan.
Permits modification of Preset scenes from an on-screen menu (recommended).
Camera cycles through Preset Scenes. Moving the joystick stops the tour.
On-screen menu changes the length of waiting time between presets.
SET-1-99-ENTER
SHOT-1-99-ENTER
ON/OFF-62-ENTER
SET/SHOT-900-ENTER
Stores the current scene and camera settings in memory. Preset 1 is shown when the camera is initialized.
Recalls the scene and camera settings from memory.
Modifies the Preset names. On-screen instructions are provided.
Presets can be removed/restored (On/Off) from the Preset tour, via an on-screen menu. Presets can still be
displayed manually.
SET/SHOT-901-999-ENTER Presets can individually be removed/restored (On/Off) from the Preset tour.
Example: SET-915-ENTER will clear Preset 15 from the tour. Presets can still be displayed manually.
ON/OFF-65-ENTER
If an alarm has been activated and the ALARM message is being displayed, it may be cleared by using
OFF-65-ENTER once. When OFF-65 ENTER is pressed again, the relay output will be deactivated.
ON-65-ENTER will activate the relay output regardless of alarm conditions.
ON/OFF-100-ENTER
Records “A” camera and PTZ controls, that can be played back. Once the sequence is recorded, you must exit
record to play back.
ON/OFF-101-ENTER
Records “B” camera and PTZ controls, that can be played back. Once the sequence is recorded you must exit
record to play back.
ON/OFF-50-ENTER
Camera will repeat “A” recorded sequence.
ON/OFF-51-ENTER
ON/OFF-52-ENTER
Camera will play the “A” recorded sequence once.
Camera will repeat “B” recorded sequence.
ON/OFF-53-ENTER
ON/OFF-14-ENTER
ON/OFF-20-ENTER
Camera will play the “B” recorded sequence once.
On-screen menu allows the setting of the
AutoPan and AutoScan speeds. Default is 30 degrees/second.
Camera will adjust for a bright background.
ON-47-ENTER
Displays the factory default settings.
ON-66-ENTER
ON/OFF-57-ENTER
ON-56-ENTER
Briefly displays the camera software versions.
Switches from color to monochrome (Day/Night models only).
On-screen menu changes Night Mode setting (On/Off/Auto; Day/Night only).
ON/OFF-78-ENTER
Allows the operator to turn tracking On and Off (AutoTrack Option only).
© 2005 Bosch Security Systems
Page 39 of 40
Americas
Bosch Security Systems
130 Perinton Parkway
Fairport, New York, 14450, USA
Phone: +1 (585) 223 4060
Fax:
+1 (585) 223 9180
E-mail: security.sales@us.bosch.com
www.boschsecurity.us
Europe, Middle East, Africa
Bosch Security Systems B.V.
P.O. Box 80002
5600 JB Eindhoven, The Netherlands
E-mail: ema.securitysystems@bosch.com
http://www.boschsecurity.com
© 2005 Bosch Security Systems GmbH
3935 890 43816 05-07 | Updated February 15, 2005 | Data subject to change without notice.
Asia-Pacific
Bosch Security Systems Pte Ltd
38C Jalan Pemimpin
Singapore 577180, Singapore
Phone: +65 319 3488
Fax:
+65 319 3499
E-mail: sg.securitysystems@bosch.com
http://www.boschsecurity.com