Heraeus T6P T12P and T20P

Add to my manuals
35 Pages

advertisement

Heraeus T6P T12P and T20P | Manualzz

GB

USA

Laboratory Drying Ovens

Models T 6 P, T 12 P, T 20 P

Operating instructions

Valid: 09.2005 / 50042749 C

Below is a list of the international Thermo marketing organizations.

Postal address Germany

Thermo Electron LED GmbH

D – 63505 Langenselbold

Robert-Bosch-Strasse 1

Enquiries from Germany

Phone

Sales

Service

0800 1 536376

0800 1 112110

Fax

Sales/Service 0800 1 112114

E-Mail [email protected]

Postal address USA

Thermo Electron Corporation.

275 Aiken Road

Asheville, NC 28804

USA

Enquiries from North America

Phone + 1 800-879 7767

Fax + 1 828-658 0363

E-Mail [email protected]

Enquiries from Europe, Middle East

and Africa

Phone + 49(0) 6184 / 90-6940

Fax + 49(0) 6184 / 90-7474

E-Mail [email protected]

Enquiries from Latin America

Phone + 1 828-658 2711

Fax + 1 828-645 9466

E-Mail [email protected]

Enquiries from Asia Pacific

Phone + 1 852-2711 3910

Fax + 1 852-2711 3858

E-Mail [email protected]

Internet: www.thermo.com

1a

Thermo Electron LED GmbH, 63505 Langenselbold, Germany function line

®

is a registered trademark of Thermo Electron LED GmbH.

If translated versions of this manual are used, the German version is the authoritative basis.

Subject to technical modifications.

This instruction manual applies for the following models:

Order No.

50 042 294

Model Equipment

T 6 P Drying oven, programmed controller, 1/PE AC, 230 V; 50/60 Hz

50 042 296

50 042 304

50 043 407

50 042 310

50 043 309

T 6 P Drying oven, programmed controller, 1/PE AC, 120 V; 50/60 Hz

T 12 P Drying oven, programmed controller, 1/PE AC, 230 V; 50/60 Hz

T 12 P Drying oven, programmed controller, 1/PE AC, 208 V; 50/60 Hz

T 20 P Drying oven, programmed controller, 1/PE AC, 230 V; 50/60 Hz

T 20 P Drying oven, programmed controller, 1/PE AC, 208 V; 50/60 Hz

The safety concerning the protection of persons, environment and material to be treated mainly depends on the behavior of the operating personnel of these units.

Please read and observe the following instructions carefully before starting the unit in

order to avoid faults and resulting damage, especially adverse health effects.

2a

Information according EN 61010

AMBIENT OPERATING CONDITIONS

For indoor use only

For altitudes up to 2000 m above sea level

Temperature range from 5 °C to 40 °C

Maximum relative humidity: 80 %, for temperatures up to 31 °C, decreasing linearly to

50 % relative humidity at 40 °C

Main power supply: Voltage fluctuations not to exceed +/- 10 % of the nominal value

ELECTRICAL DATA

Overvoltage category: II

Contamination level: 2

WEEE Compliance:

This product is required to comply with the European Union`s Waste Electrical & Electronic

Equipment (WEEE) Directive 2002/96/EC. It is marked with the following symbol:

Thermo Electron has contracted with one or more recycling/disposal companies in each EU

Member State, and this product should be disposed of or recycled through them. Further information on Thermo Electron`s compliance with these Directives, the recyclers in your country, and information on Thermo Electron products wich may assist the detection of substances subject to the RoHS Directive are available at www.thermo.com/WEEERoHS.

2b

CONTENTS

1. GENERAL SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 - 6

Explanation of icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

General information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Operating instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Field of application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

2. SETUP AND INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 - 9

Transport . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Unpacking the unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Room ventilation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Mains connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Noise insulation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Connecting to an air extraction system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

3. UNIT SPECIFICATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 - 16

Overview of the control elements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Switchgear unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

On / Off switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Overtemperature protection feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 - 11

Automatic control unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Signal lamps, status function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Basic functions: temperature control, time switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Added-feature programming functions, fixed programs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Fixed program segments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Compilation of a fixed program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Example of a fixed program hot-air sterilization prozess . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Programmed controller function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Termination commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Example of a temperature/time program, definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

What happens if ... ? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

4. OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 - 26

Starting up with

Basic functions - temperature control, time switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 - 18

Added-feature programming functions, example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 - 20

Programmed controller functions, example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 - 25

Operating guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Loading . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

5. MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 - 28

Decontamination / disinfection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Servicing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Tests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Repairs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Approved spare parts / accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

6. TECHNICAL DATA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 - 31

Oven . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 - 30

Control unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Materials used . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

LOG BOOK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

50 042 749 3

1 GENERAL SAFETY INSTRUCTIONS

EXPLANATION OF ICONS

This symbol marks chapters and sections of this instruction manual which are particularly relevant to safety.

When attached to the unit, this symbol draws attention to the relevant section of the instruction manual.

Marks information about optimum utilization of the unit in the instruction manual.

Warns of hot surfaces.

s e t

Key for temperature selection, time-switch function and to confirm entered information prog

Key for the programming function, time selection and to confirm entered information

Value adjustment key, INCREASE VALUE

Value adjustment key, REDUCE VALUE

Information about proper disposal / recycling

Overtemperature protection device

Quick reference guide to operation

Select the status of the control unit (enabled / disabled)

Temperature control function, select temperature

Time-switch function, set the operating times

P

Programming function

4 50 042 749

1 GENERAL SAFETY INSTRUCTIONS

General information

The unit fulfils the following safety standards:

DIN EN 61 010 - 1 / 03.´94, VDE 0411 Part 1 / 03.´94, E DIN VDE 0411 Part 111,

DIN 12 880 Part 1 / 11.´78 and DIN EN 60 335 - 1, VDE 0700 Part 1

DIN EN 55 011 Part 3, DIN VDE 0875 Part 11 / 07.´92

Always quote the data on the rating plate when requesting information or ordering spare parts

Operating instructions

The operator must provide anybody working on or with this equipment with written instructions for any operations to be performed. Such instructions must be easy to understand and must be available in the language of the respective personnel (FRG: UVV VBG 1 § 7 (2)).

Log book

We recommend that a log book is kept, which records any tests and calibration operations performed on the unit and any other work (repairs, modifications etc.).

Field of application

The drying oven has been designed as an item of laboratory equipment for technical applications.

Heat treatment of samples or materials with operating temperatures of between

room temperature + approx. 10°C and 250 °C, e.g. for drying, ageing, analysis, fusing, burning in, oxidizing, reducing, preheating, etc.

Hot-air sterilization, sterilization by heating the article up to a temperature of at least 160 °C

(FRG: also refer to DIN 58 947).

Note: The sterilization temperature usually required in the field of medical laboratory work is 180 °C.

The unit has been designed for installation and operation in the following fields:

Laboratories, e.g. in the commercial or industrial sector, schools, universities, hospitals and biology

The unit is equipped with an independent overtemperature protection device, which means that it does not require constant supervision.

The drying oven has been designed for continuous use.

Make sure that an adequate clearance is maintained between the inside walls of the inner compartment and the loaded articles, and between the various layers of loaded articles, to prevent uneven heating of the materials.

Protective gloves, goggles etc. must be made available to the operator because of the potentially high operating temperatures.

The unit must not be used to dry or heat substances which may release combustible gases or vapours into the atmosphere, which could burn or explode when mixed with air.

The drying oven is equally unsuitable for the heat treatment of combustible dusts or fibrous materials.

50 042 749 5

1 GENERAL SAFETY INSTRUCTIONS

Safety instructions

Comply with the instructions in this manual and keep it in the vicinity of the unit.

These unit must be operated in accordance with the instruction manual and may only be used for their intended applications in order to ensure the safety of personnel, the environment and the processed items and materials.

Read the instruction manual carefully and comply with the instructions that it contains to avoid making mistakes and to prevent any personal injury or damage to property.

Unit must be operated by instructed personnel.

Keep unit out of reach of children.

Apart from the instructions in this manual, the respective national regulations must also be observed for the installation and operation of this unit (FRG: ZH 1/119, DIN 12 880 Part 1).

The applicable national environmental regulations must be observed for the extraction of exhaust gases that are produced during heat treatment. Suitable measures must be implemented to ensure that such gases are safely led outside (FRG: BImSchG, UVPG, AbfG, WHG, ChemG, ...).

The unit must not be used to dry or heat substances which may release combustible gases or vapours into the atmosphere, which could burn or explode when mixed with air. The heating is equally unsuitable for the heat treatment of combustible dusts or fibrous materials.

Check the mains lead and connector for damage before using the unit. If there are any signs of damage, do not connect the unit up to the mains.

The voltage quoted on the rating plate (rated voltage) must agree with the mains supply voltage.

Protective gloves, goggles etc. must be made available to the operator because of the potentially high operating temperatures.

The surfaces around the opening of the inner compartment become hot at high operating temperatures - RISK OF BURNING - Avoid contact with these surfaces.

Ensure that the overtemperature protection device works properly by conducting a functional check at regular intervals, every 3 months at least, and check the electrical equipment at least once a year.

Any work to be conducted on the electrical equipment of the unit may only be performed by a qualified electrician. The unit must be disconnected from the mains supply before commencing service or repair work.

Only use approved accessories and approved genuine spare parts. The use of any other parts may result in unforeseen problems and should be avoided under all circumstances.

The serviceability and safety of the unit can only be guaranteed if the necessary tests, maintenance, servicing and repair work is carried out by the Thermo service personnel or other agencies who are authorized to act on our behalf.

Thermo Electron LED GmbH cannot accept any liability for any damage that occurs as a result of improper use or repair work, which has not been performed by Thermo service centers, or if parts other than the approved genuine spare parts / accessories are used.

6 50 042 749

2 SETUP AND INSTALLATION

Transport

Handle the unit with care. Avoid jarring and protect against damage. Do not lift by the door handle, the door itself, the control unit, the spacer or the power lead.

Refer to the TECHNICAL DATA for dimensions and weight.

Unpacking the unit:

Unpack the unit, remove the transport safety fixtures from the inner compartment and remove any dirt or dust which may have accumulated in transit.

Installation

The unit must be installed in a dry environment.

The relative humidity should be between 60 and 70 % under normal conditions.

Condensation should be avoided. If condensation has formed on the unit following a change of location or during transporation, for example, wait until the unit has dried out completely before putting into operation.

The ambient air should not contain excessive amounts of dust.

(Comply with the instructions in the MAINTENANCE section).

Do not cover or obstruct the ventilation or exhaust vents in the unit housing, remove any dust or dirt with a vacuum cleaner.

The ambient temperature should not exceed 40 °C.

Place the unit on a firm, fireproof surface (e.g. laboratory table, support frame) in a stable, perfectly upright position.

Keep the unit away from direct sunlight (UV radiation).

If you wish to stack two units on top of one another, use the stacking frame (available as an option). Never stack more than two units on top of one another. When stacking units of different types, make sure that e.g. an incubator is always at the bottom, and prevent any mutual influence. Only units of the same size are stackable. In case of stacking two units inside a niche the clearance to adjacent surfaces has to be increased on minimum one side to 200mm.

Fig. 1/2: Clearances to adjacent surfaces / objects:

5 cm

30 cm

5 cm

Maintain a distance from back wall:

T 6 P: at least 8 cm

T 12 P:

T 12 P: at least 8 cm at least 8 cm

The wall spacer may only be removed if the unit is connected up to an extraction system.

The exhaust gases must be led through / past adjacent surfaces / objects located above or behind the unit with heat insulation to avoid the danger of fire.

If the unit T 6 Pis to be fitted under a table or into a laboratory fixture, it must be connected to an exhaust air extraction system. The top clearance may only be reduced to min. 5 cm under such circumstances. Ensure adequate ventilation.

Types T 12 P and T 20 P are not suitable to be fitted under a table.

50 042 749 7

2 SETUP AND INSTALLATION

Room ventilation

Adequate ventilation must be provided wherever the unit is installed.

Do not operate the unit in non-ventilated enclosed spaces.

Special ventilation measures (e.g. ventilation of designated work areas, FRG: also refer to VDI

1946 Part 7) when several units are installed in one room.

Mains connection

The unit is supplied with a permanently connected, flexible mains power lead with connector

(grounded).

The connector serves to disconnect the unit from the mains power supply.

Examine the power lead and connector for damage before using the unit. If there are any signs of damage, do not connect the unit to the mains supply.

The voltage quoted on the rating plate (rated voltage) must agree with the nominal mains

voltage.

The unit may only be connected up to the mains via a properly installed socket outlet with PE

conductor (protection class I) or a permanent terminal connection.

In the event of a permanent terminal connection, a master switch (lockable in the "Off" position) must also be installed to disconnect the unit from the mains.

An earth-leakage circuit-breaker should also be fitted in the supply system to provide

additional protection against electric shocks.

Rubber-sheathed flexible cable of at least 2.5 mm 2 diameter (H 07 RN-F ...) should be used for any extensions that may be required to connect the unit.

Refer to the TECHNICAL DATA section for the rated power consumption, circuit protection with a T 16 A fusible link or a B 16 circuit-breaker.

Noise insulation

The unit does not develop any constant noise load.

Refer to the TECHNICAL DATA section for the noise level.

The unit may produce higher noise levels in unfavorable installation conditions. Supplementary measures may have to be implemented to improve the sound insulation in the room.

8 50 042 749

2 SETUP AND INSTALLATION

Connecting to an exhaust air system

Comply with the applicable national environmental regulations for the extraction of exhaust gases released during the heat treatment. Suitable measures must be implemented to ensure that such gases are safely led outside (FRG: BImSchG). Such measures may involve thermal or catalytic treatment of flue gases.

Refer to the TECHNICAL DATA section for the volume flow and temperature of the exhaust

gases.

Fig. 2/2: Example of an installation

3

2

1

5

4

6

3

4

1

2

5

6

Inlet air flow

Unit

Adjacent surface / object

Exhaust-air blower

Exhaust air flow

Draft breaker

Implementation instructions:

A draft breaker must be used to connect the unit to an extraction system.

All flue ducts must be made of fireproof materials.

Apertures must be provided to enable the removal of residue and condensate. The flue

ducts must be thermally insulated (recommendation: half-shell sleeves made of laminated mineral fiber).

The exhaust air / gases from the unit must never come into contact with combustion ex-

haust gases.

Use the draft breaker to adjust the air flow volume in such a way that exhaust gases can be extracted reliably without producing any eddying at the unit's exhaust-gas connector.

Technical measures should be implemented to monitor the flow of air and flue gases and to prevent operation of the heating unit if the ventilation system is switched off / defective

(electrical interlock).

50 042 749 9

3.

UNIT SPECIFICATION

Fig. 1/3: Overview of the control elements

C

B

A Switchgear unit

B Automatic control unit

C Door handle

A

Item A: Switchgear unit

Fig. 2/3: Switchgear unit control panel

1 o n off

2

3

1

2

3

On / Off switch

Overtemperature protection, control element

"Fault signal lamp

1 ON / OFF switch:

To switch the unit on and off:

"on" = Unit switched on, the temperature inside the unit appears on the display panel of the control unit.

"off" = Unit switched off, temperature display off.

2 & 3 Overtemperature protection device / signal lamp:

The unit is equipped with an electronic upper-limit cut-out device (TWB) of protection class 2 as defined by DIN 12 880 Part 1. It is electrically and functionally independent of the temperature control system. In the event of a fault in the unit heating system, the operational TWB shuts down the unit heating across all poles as soon as the temperature exceeds the preset value.

The red signal lamp indicates activation of the protection function (Fig. 2/3: Item 3).

The unit must be reset manually, by pressing the control element.

Allow the unit to cool down (by approx. 30 °C), press the control element, the red signal lamp will go out.

The operate value is adjusted with the help of a tool (coin, screwdriver...).

Adjust to the required protection level: to upper temperature limit = unit protection (protects the unit and its environment).

to approx. 10 °C higher than the operating temperature set on the control unit =

material protection (protects the unit, its environment and the loaded material).

Ensure that the overtemperature protection device works properly by conducting a functional check at regular intervals, every 3 months at least, and check the electrical equipment at least once a year.

10 50 042 749

3.

UNIT SPECIFICATION

2 & 3 Overtemperature protection device / signal lamp:

Functional test of the TWB

(Prerequisite: required working temperature (control unit) has been reached /remains constant)

Set the TWB to approx. 10 - 20 °C below the temperature displayed on the control unit. The

TWB must respond, the red signal lamp indicates "Fault".

The TWB is working properly. Press the control element to release the TWB.

Now set the TWB to the temperature limit for the required type of protection.

If "Fault" is signalled during operation:

Check the settings of the TWB and the control unit and correct if necessary. If the problem persists, contact the service center.

Item B: Automatic control unit

The automatic control unit contains the basic functions of a 2-position controller with PD/PID control response, time switch to switch the heating on / off after the set time, the added features of permanently programmed heating process programs and the programmed controller

functions of a freely programmable process controller.

Fig. 3/3: Control unit control panel

1

°C

2 3 4 set prog

5

3

4

5

6

7

1

2

Signal lamp - heating status

Signal lamp - control unit status

Display panel

Control key

"Increase displayed value" key

"Reduce displayed value" key

"Programming function" key

7 6

The status of the control unit is indicated by signal lamps in the display panel.

THE YELLOW SIGNAL LAMP (Item 1) indicates the current status of the heating control system:

Lamp switched on = unit heating activated

Lamp switched off = heating off

Rhythmic flashing of this signal lamp indicates that the temperature controller is regulating the operating temperature.

THE GREEN SIGNAL LAMP (Item 2) indicates the status of the control unit:

Lamp on = control unit switched on: heating enabled.

The heating is activated when the unit is switched on (On / Off switch).

Lamp off = control unit switched off: heating disabled.

The heating is not activated when the unit is switched on.

Lamp flashes = time-switch function activated.

50 042 749 11

3.

UNIT SPECIFICATION

Basic functions

The control unit is equipped with the "temperature control" and "time switch" basic functions. The unit can set an operating temperature of up to 250 °C and switching times of between 0:01 and 99:00 hours.

Refer to STARTING UP WITH BASIC FUNCTIONS for information about the commands for the basic functions.

Added-feature programming functions, fixed programs

The control unit is capable of running heating process programs with fixed, preselected parameters from a database. The program segment and the parameters are stored in the

database.

The fixed program contains a maximum of four program segments and a status command.

Only one fixed program can be stored. In the programmed controller function one arbitrary difined program can be stored independend of the fixed program.

Fig. 4/3: Example of a temperature/time process, controlled by the fixed program

P I P 2 P 3 P 4 P 5

T (°C)

T

T t h o l d t o n

P I. 0 - P I. 9

1 h

P 2 . 0 - P 2 . 9 P 3 . 0 - P 3 . 9

1 h

P 4 . 0 - P 4 . 9 t ( h )

P . o F

P . o n

P . r E

Each program segment, P I - P 4, is assigned to a typical temperature / time response. 10

selectable sets of parameters are permanently stored in the database for each program

segment. These sets of parameters can be assigned within the program.

A status command is provided as the fifth program segment. This determines the subsequent action with the program selected from the fixed program memory:

Program on standby, do not execute yet = Select " P. o F "

Program on standby, wait for program start = Select " P. o n "

Delete program from memory completely = Select " P. r E "

The program memory is erased on delivery. If the operator interrogates the program segments,

"Parameter set off" appears in the display panel = e.g. " P. I - ".

When compiling a program, selecting "parameter set off" within the selected program segment causes the control unit to bypass this segment for the fixed program function.

The selected program always runs from program segment P I. n to program segment P 4. n.

If program segment P 3. n is combined with program segment P 4. n, the heating and blower are only switched off following termination of segment P 4. n.

If a program is interrupted and started again, the sequence commences at segment P I. n.

The previously selected operating temperature cannot be changed once the program has started.

The heating is switched off in the event of a power failure (> 20 ms) with subsequent restoration of the power supply, the temperature inside the unit is displayed as a flashing value and the program must be started again.

12 50 042 749

3.

UNIT SPECIFICATION

Fixed program segments:

Program segment " P 1. n " (n = -, 0 ... 9):

Assigning a parameter ( 0 ... 9 ) from the database causes the unit to switch on heating on expiry of a

preset period.

Selectable parameters in this program segment:

P I. off

P I. 0 P I. I

2 h 4 h

P I. 2 P I. 3 P I. 4 P I. 5 P I. 6 P I. 7 P I. 8 P I. 9

6 h 8 h 10 h 12 h 16 h 20 h 24 h 72 h

Program segment " P 2. n " (n = -, 0 ... 9):

Assigning a parameter ( 0 ... 9 ) causes the unit to heat up to the preset operating temperature at a specific rate of temperature change per hour.

1)

Selectable parameters in this program segment:

P 2. P 2. 0 P 2. I P 2. 2 P 2. 3 P 2. 4 P 2. 5 P 2. 6 P 2. 7 P 2. 8 P 2. 9 off 10°C/h 20°C/h 30°C/h 40°C/h 50°C/h 60°C/h 80°C/h 100°C/h 120°C/h 200°C/h

Program segment " P 3. n " (n = -, 0 ... 9):

Assigning a parameter ( 0 ... 9 ) causes the unit to heat up to the preset operating temperature, to

maintain this temperature for the preset period and to subsequently switch off heating

Selectable parameters in this program segment:

P 3. P 3. 0 P 3. I P 3. 2 P 3. 3 P 3. 4 P 3. 5 P 3. 6 P 3. 7 P 3. 8 P 3. 9 off 15 min. 30 min.

1 h 1.5 h 2 h 4 h 6 h 8 h 12 h 24 h

Program segment " P 4. n " (n = -, 0 ... 9):

Assigning a parameter ( 0 ... 9 ) causes the unit to cool down from the previously reached inside

temperature at a specific rate of temperature change and to subsequently switch off heating.

1)

Selectable parameters in this program segment:

P 4. P 4. 0 P 4. I P 4. 2 P 4. 3 P 4. 4 P 4. 5 P 4. 6 P 4. 7 P 4. 8 P 4. 9 off 1°C/h 2°C/h 5°C/h 10°C/h 20°C/h 30°C/h 40°C/h 50°C/h 60°C/h 80°C/h

1) according to model and load

Compilation of a fixed program

After activating the added-feature function, the sequence is compiled by marking the required program segments.

Example: Fixed program comprising P I. 2; P 2. -; P 3. 7; P 4. 4 and P. o n :

P I.-

P 2.-

P 3.-

P 4 . -

P . o F

P I . 0

2 h

P I. I

4 h

P I . 2

6 h

P I . 3

8 h

P I . 4

10 h

P I. 5

12 h

P I. 6

16 h

P I. 7

20 h

P I. 8

24 h

P I. 9

72 h

P 2 . 0 P 2. I P 2 . 2 P 2 . 3 P 2 . 4 P 2 . 5 P 2 . 6 P 2 . 7 P 2 . 8 P 2 . 9

10°C/h 2 0 ° C / h 3 0 ° C / h 4 0 ° C / h 5 0 ° C / h 6 0 ° C / h 80°C/h 1 0 0 ° C / h 120°C/h 2 0 0 ° C / h

P 3 . 0

1/4 h

P 3. I

1/2 h

P 3 . 2

1 h

P 3 . 3

1,5 h

P 3 . 4

2 h

P 3 . 5

4 h

P 3 . 6

6 h

P 3 . 7

8 h

P 3 . 8

12 h

P 3 . 9

24 h

P 4 . 0

1 ° C / h

P 4. I

2 ° C / h

P 4 . 2

5 ° C / h

P 4 . 3 P 4 . 4 P 4 . 5 P 4 . 6

1 0 ° C / h 2 0 ° C / h 3 0 ° C / h 4 0 ° C / h

P 4 . 7

5 0 ° C / h

P 4 . 8

6 0 ° C / h

P 4 . 9

8 0 ° C / h

P.o n P.r E

50 042 749 13

3.

UNIT SPECIFICATION

Example of a fixed program

Example E1: Hot-air sterilization process

The heating should switch on in 8 hours, the unit should heat up to an operating temperature of

190 °C (sterilization temperature) at a rate of 200 °C/h, maintain this temperature for 4 hours

(equalization phase and sterilization period) and should subsequently cool down at a rate of 20

°C/h.

The program should start following program selection (status command: P. on).

Fig. 5/3: Program profile - hot-air sterilization process E1

T

190 °C

S 1 S 2 S 3 S 4

S 1 - S 4 = Programmsegment

P I. 3 P 2. 9 P 3. 5 P 4. P. o n t

Sequence E1:

After sketching the process characteristic, select the segments which correspond to the required sequence from the matrix .

Mark the program segments and the " P. o n " status command. Leave program input mode.

Select 190 °C as the required operating temperature. Start the fixed program.

While the program is running the display alternates between the temperature inside the unit and the current program segment.

Refer to STARTING UP WITH ADDED-FEATURE PROGRAMMING FUNCTIONS for further information.

14 50 042 749

3.

UNIT SPECIFICATION

Programmed controller function

The programmed controller function enables the arbitrary definition of temperature / time processes.

You may select up to 9 program segments. Operating temperature and period can be selected for each segment.

Termination commands

A termination command can be selected as the last program segment beginning at the second segment. The termination command determines the function to be performed by the unit after running through the program.

There are three optional termination commands:

" hold " = Once the program has terminated, the operating temperature set for the last program segment is maintaned until a new operating temperature has been selected.

" StOP " = Once the program has terminated, the heating is switched off until the "stop" command is cancelled.

" CYCL " = Once the program has terminated, it returns to the beginning and is repeated continuously until the "CYCL" command is cancelled.

A termination command must always be entered at the end of every program.

Fig. 6/3: Example of a temperature / time program with "CYCL" termination command

U/T

T1 T2 T7 T8

Un

Tn

T3

T4

T5 T6

T9 n 1 n 2 n 3 n 4 n 5 n 6 n 7 n 8 n 9 t1 t2 t3 t4 t5 t6 t7 t8 t9 t n 10 = CYCL

Definitions n 1 ... n 9 n 10

T 1 ... T 9 t 1 ... t 9

Program segments

Termination commands (hold, StOP or CYCL)

Specified operating temperature (50 - 250 °C)

Specified time - program segment (0:01 - 99:0 h)

After a power failure >20ms up to approx. 2h the program will be continued at the last temperature/time-values.

Refer to STARTING UP WITH PROGRAMMED CONTROLLER FUNCTIONS for details.

50 042 749 15

3.

UNIT SPECIFICATION

What happens if ... ?

Possible display

8 8 8

Explanation

Control unit test phase o F F Status of the control unit, heating disabled, possibly time-switchfunktion has been aktivated signal lamp - control unit status flashes

P 1.3 alternating with inside temperature time-switch function activated

One digit in the display flashes The flashing value can be changed

P 1.3

Program segment when entering an added-feature program function

Program segment while the added-feature program is in progress

P. o n

P. o F

P. r E

P r o alternating with inside temperature n I hold

StOP

CYCL

Status command for an added-feature program:

Program on standby, wait for program start

Status command for an added-feature program:

Program on standby, do not execute yet

Status command for an added-feature program:

Delete program from memory completely

Entered program on standby

Power failure (> 20 ms) with subsequent restoration: the heating switches off, "P r o" alternates with the temperature inside the unit on the display, if a program is in progress it is interrupted and must be started again.

Program segment when entering and activating the programmed controller function.

Termination command when entering the programmed controller function: the temperature set for the last program segment is maintained on termination of the program

Termination command when entering the programmed controller function: the heating and ventilation is switched off on termination of the program

Termination command when entering the programmed controller function: when the program is terminated, it returns to the beginning and starts again

- - -

E - 3

E - 4

E - 5

E - 6

E - 7

E - 8

E - 9

A termination command is entered for this program segment when entering the programmed controller function. The termination command must be changed to a time value to enable the input of a temperature value.

Stored data defective

Switch the unit off and on again. If the problem persists, contact the service center

Error of measurement in the reference values

- contact the service center -

Upper-limit violation of actual temperature tolerance

- contact the service center -

Lower-limit violation of actual temperature tolerance

- contact the service center -

Temperature sensor or input defective - contact the service center -

Stored data defective - contact the service center -

Erroneous reference values - contact the service center -

16 50 042 749

4 OERATION

After setup and installation, proceed as follows to start up:

Starting up with basic functions, without programming

Instruction

Switch unit on

Key(s)

On / Off switch = "on"

Example of display Remarks

The green status display indicates the status.

Display panel: inside temperature

The unit runs through a self-test phase after switching on, display: " 888 ".

If the "off" status was selected for the previous operating phase, the display alternates between the temperature inside the unit and the "oFF" status.

Selecting the control unit status function

Control unit "on":

(heating enabled) approx. 3 sec.

Inside temperature, green signal lamp lights up continuously

Select this status function to operate the unit, or to use the time-switch function to switch the heating off after a preset period

Control unit "off":

(heating disabled) approx. 3 sec.

Inside temperature alternating with "off", green signal lamp remains dark

Select this status function to switch the heating and off, or if the heating is to remain off during programming, or to use the time-switch function to switch the heating on after a preset period

Setting the operating temperature

Display the preset operating temperature s e t

Preset operating temperature

Increase the preset operating temperature

Display flashes

Value increases

Reduce the preset operating temperature

Display flashes

Value decreases

Display flashes

Store new preset operating temperature s e t

Unit regulates the operating temperature when status "on", yellow signal lamp indicates the status of the heating control system.

Adjusting the overtemperature protection device: refer to Chapter 3

New operating temperature is stored, then inside temperature appears on display

>>>

I 50 042 749 17

4 OPERATION

>>>

Setting the switching time

Instruction

Select time-switch function, display time remaining for timing period

Increase preset time

Reduce preset time

Key(s) s e t approx. 3 sec.

Example of display Remarks

Display flashes, time-switch funcition is displayed. If timing period in progress, displays time remaining

Value can be adjusted between 1 minute and 99 hours. Adjustable in full hours from 10.0 hour setting.

The heating is switched on or off, according to set status, once timing period has expired, e.g. control unit status "off" - time-switchfunction switches "on".

Store new preset time value s e t

The time value is transferred to the memory, the inside temperature then appears on the display.

The flashing status display indicates that the time-switch function has been activated. In this case the status of the control unit "on " or "off" can´t be changed, if desired the switching time has to be set to "0.00".

If you do not wish to use the time-switch function, enter 0. 0 0 as the preset time.

18 50 042 749

4 OPERATION

Fig. 1/4: Example of a hot-air sterilization process

T

190 °C

S 1 S 2 S 3 S 4

S 1 - S 4 = Programmsegment

P I. 3 P 2. 9 P 3. 5 P 4. P. o n t

The heating is to switch on in 8 hours, the unit should heat up to 190 °C at 200 °C/h, maintain this temperature for 4 hours, then switch off.

The program should start following program selection (P. o n).

Starting up with added-feature programming functions

Instruction Key(s) Example of display Remarks

Switch unit on, select operating temperature: refer to start-up with basic functions

Adjusting the overtemperature protection device: refer to Chapter 3

Control unit "off", unit should not heat up during this input approx. 3 sec.

Status display = "oFF", control unit is disabled, inside temperature is displayed

Call fixed program memory

Select parameter PI. 3 s e t s e t approx. 6 sec.

Display flashes, program segment S1 appears after 6 sec.

Programmable digit flashes.

P I. is displayed if no parameter has been marked

Programmable digit flashes

Mark P I. 3 as the required parameter in program segment S1

Select program segment S2 s e t

P I. 3 is transferred to the memory, programmable digit flashes

Programmable digit flashes

Continue in the same manner to enter / mark program segments P 2. 9, P 3. 5 und P 4.

>>>

50 042 749 19

4 OPERATION

>>>

Entering the status command

Instruction

Call status command

Key(s)

Select status command s e t

Mark status command s e t

Leave program memory

Input terminated

Starting the added-feature program

Start the program approx. 3 sec.

Terminating the added-feature program

Terminate the program approx. 3 sec.

Example of display Remarks

P. o F is displayed

P. o F flashes

P. o n flashes

P. o n is displayed

Display alternates between inside temperature and

" P r o "

Program is started, the display alternates between the temperature and the program segment

Display alternates between the inside temperature and

" P r o "

20 50 042 749

4 OPERATION

Fig. 2/4: Example of the programmed controller function with " StOP " termination command

T

230 °C

T1 T2 T7 T8

T3

T4

T5 T6

150 °C

70 °C

T9 n1 n2 n3 n4 n5 n6 n7 n8 n9 t1 t2 t3 t4 t5 t6 t7 t8 t9 t n 10 = StOP

The program sequence from a total of 9 segments must be entered, after which the heating is to be switched off.

Starting up with programmed controller functions

Instruction Key(s)

Switch the unit on, refer to start-up with basic functions

Example of display

Adjusting the overtemperature protection device: refer to Chapter 3

Control unit "off", unit should not heat up during this input approx. 3 sec.

Remarks

Inside temperature, green signal lamp lights up continuously

Call main program memory s e t

& prog

Program segment

"n I" is displayed, programmable digit flashes

>>>

50 042 749 21

4 OPERATION

>>>

Entering the time for a program segment

Instruction

Enter the time for program segment n I,

2:00 h

Key (s) prog or

Example of display Remarks

The time for n I flashes in the display

Time t 1= 2 . 00

Transfer the preset time for program segment n I to the memory prog n I is displayed, programmable digit flashes

Entering the temperature for a program segment

Enter operating temperature T 1,

230 °C set

Preset operating temperature for program segment

1(n I) flashes in display

If " - - - " appears in the display when the set key is pressed, then "hold" or "StOP" has been entered as the termination command for program segment n I. If you wish to enter a temperature value, you must first change the termination command to a time value (refer to the section on "Entering the time for a program segment").

or Enter 230 °C

Transfer temperature

T1=230 °C to the memory set

Program segment

" n I " is displayed, programmable digit flashes

Select next program segment

Select program segment n 2 n 2 is displayed, programmable digit flashes

Enter the preset operating temperatures and taime values for program segments n 2 - n 9 in the same manner as for program segment n 1 and select program segment n 10.

>>>

22 50 042 749

4 OPERATION

>>>

Selecting the termination command

Select the "StOP" termination command prog

Termination command flashes in the display

Enter the "StOP" termination command n 10 is displayed, programmable digit flashes

Transfer the termination command to the memory prog

Leaving the program memory

Instruction Key (s)

Leave the program memory s e t

& prog

Display Remarks

Inside temperature is displayed

Input terminated

Starting the program

Instruction

Start the program

Key (s) prog approx. 6 sec.

Example of display Remarks

Inside temperature and program segment are displayed

Terminating the program

Instruction Key(s)

Terminate the program prog approx. 6 sec.

Example of display Remarks

Inside temperature and control unit status are displayed

50 042 749 23

4 OPERATION

Fig. 3/4: Example of the programmed controller function with " hold " termination command

Tn

T

T1

100 %

T2

70 % T3

40 % n 1 n 2 t1 t2 n 3 t3 n 4 = hold t

Starting up with programmed controller function

The "hold" termination command has been selected here as an alternative to example 2/4.

Enter the preset temperature and time values for the program segments according to the same procedure as example 2/4.

Instruction Key(s) Example of display Remarks

Select program segment n 4 n 4 is displayed, programmable digit flashes

Select the "hold" termination command prog

Termination command flashes in the display or

Transfer the termination command to the memory prog

Leave the program memory and start the program

Enter the "hold" termination command n 4 is displayed, programmable digit flashes

24 50 042 749

4 OPERATION

Fig. 4/4: Example of the programmed controller function with " CYCL " termination command

Tn

T

40 % n 1

T1

70 %

T2

100 % n 2 n 3

T3

40 % n 4

T4 t1 t2 n 5 = C Y C L t3 t4 t

Starting up with the programmed controller function

The "CYCL" termination command has been selected here as an alternative to example 2/4.

Enter the preset temperature and time values for the program segments according to the same procedure as example 2/4.

Key(s) Example of display Instruction

Select program segment n 5

Remarks n 5 is displayed, programmable digit flashes

Select the "CYCL" termination command prog

Termination command flashes in the display or

Transfer the termination command to the memory prog

Leave the program memory and start the program

Enter the "CYCL" termination command n 5 is displayed, programmable digit flashes

50 042 749 25

4 OPERATION

Operating guidelines

Remember to put on protective garments, e.g. gloves, goggles, mask, body protection, remove any items of jewellery before starting work.

Do not cover or obstruct the ventilation or exhaust vents in the unit housing. Always keep these vents free of dust and dirt.

Loading:

Circulating air conducts the heat to the samples in the unit. Make sure that the samples are evenly distributed on the trays, and that they are arranged in such a way as to ensure an unimpeded flow of warm air throughout the cabinet, in order to prevent local overheating. Do not position the samples too close to the inner walls.

Fig. 5/4: Loading diagram a a

"a" = approx. 1/10 of the internal dimensions a a

Be careful not to damage the temperature sensors in the inner chamber when loading.

Never place samples on the floor of the chamber!

Keep the inner surfaces of the chamber free of dust and dirt. Never use aggressive chemicals which could damage the stainless steel finish.

Continually heating and cooling the unit over wide temperature ranges can detrimentally affect its service life. If used more frequently, it is better to keep the unit running in continuous mode at moderate temperatures.

If not used for an extended period, disconnect the unit from the power supply.

Shutdown

Remove the samples from the chamber

Allow the heating unit to cool down to room temperature

Switch the unit off and disconnect from the mains

Clean the inside surfaces of the chamber

(also refer to the section on DECONTAMINATION, CLEANING ...)

26 50 042 749

5 MAINTENANCE

The serviceability and safety of the unit can only be guaranteed if the necessary tests, maintenance, servicing, and repair work is carried out by the Thermo service personnel or other agencies who are authorized to act on behalf of Thermo Electron LED GmbH.

Thermo Electron LED GmbH cannot accept any liability for any damage that occurs as a result of improper use or repair work, which has not been performed by Thermo service centers, or if parts other than the approved genuine spare parts / accessories are used.

We recommend that you enter into a service contract with our company. Please contact us for a quotation.

Decontamination / disinfection

The operator is responsible for implementing suitable, effective measures to decontaminate the unit if it is used in connection with hazardous materials. Such measures must be conducted on a regular basis under normal operating conditions and in particular if such materials have been spilt or before commencing service work.

The stainless steel components inside the unit may be decontaminated by wiping out with a

disinfectant solution in cases of biological contamination.

A surface disinfectant recommended by Thermo can be ordered under part number

50052425 (250 ml spray bottle) and 50051939 (500 ml refill bottle).

Details for efficiency and approvals are available on request.

The applicable national regulations must be observed with respect to disinfection (FRG:

ZH 1/598 ... )

Once removed, the internal stainless steel components may also be subjected to steam

sterilization or autoclave treatment.

Cleaning

Use a mild soap solution (water and mild detergent) and a soft lint-free cloth to wipe the outer

surfaces and control elements of the .

Remove any dust deposits from the air vents with a vacuum cleaner.

Remove any dust or dirt from the inner chamber. Use stainless steel cleaning agents in moderate quantities. Never use acids, chloric solvents or salt solutions to clean the stainless steel surfaces inside the unit.

Avoid scouring and scratching, or damage to labels and paintwork will be unavoidable.

Include flue/exhaust ducts in the cleaning operations if the unit is connected up to an extraction system.

Consult the manufacturer before implementing any other cleaning or disinfection measures than those mentioned in this manual to ensure that the intended methods will not damage the unit.

50 042 749 27

5 MAINTENANCE

Servicing

The unit is virtually maintenance-free.

Lubricate the bearings of the door and door-handle mechanisms with a little synthetic oil from time to time.

Mineral oil products must not be used where they may come into contact with plastic components, as they could cause damage to such parts.

Tests

The following items should be tested at least once a year to ensure that the unit remains in good working order:

Mechanical functions

Operation in accordance with the specified technical data

Electrical system (FRG: UVV VBG 4, DIN VDE 0701 Part 1, E DIN VDE 0702 / 11.93)

Safety devices

Repairs

Only approved genuine spare parts and accessories may be used.

The use of other parts may result in unforeseen problems and should be avoided under all circumstances.

Approved spare parts / accessories

Spare part /accessory

Size / model

Instruction manual

Circuit diagram 1/PE AC, 230 V/208V

Circuit diagram 1/PE AC, 120 V

Wire tray with supporting straps

Stainless steel perforated shelf with supports

Seasoned silicone rubber door seal

T 6 P

Kendro order number

T 12 P

50 043 078

T 20 P

50 040 640

50 041 987

-

50 042 913 50 042 914 50 042 915

50 044 620 50 044 610 50 044 621

50 042 499 50 042 484 50 042 351

Stacking frame

Support frame 780mm high

Support frame 300mm high

Foot

Clasp for the door latching mechanism

50 042 906 50 042 907 50 042 908

50 045 045 50 045 046 50 045 047

50 045 049 50 045 050 50 045 051

50 042 541

50 042 284

Other spare parts and accessories to order

28 50 042 749

6 TECHNICAL DATA

DATA

MECHANICAL

Dimensions

(W x H x D)

Minimum clearances to adjacent surfaces / objects

Volumes

Weights

Trays, max. tray load

Model

Housing

Chamber

Useful space 1)

Left

Right

Top

Rear

Inside (empty)

Useful space 1)

Steam space

Unit

Lumped

Surface

Total

Standard / Max.

(W x D):

T 6 P T 12 P T 20 P

552 x 700 x 685 696 x 850 x 685 754 x 910 x 865 mm

352 x 424 x 386 496 x 575 x 386 554 x 637 x 566 mm

281 x 339 x 308 396 x 460 x 308 443 x 509 x 452 mm

50 mm

50 mm

300 (50 when connected to an extraction system)

120 80 80 mm mm

57.6

29.5

approx. 73 approx. 40

15

110

56 approx. 131 approx. 55

15

199.7

102 liter liter approx. 234 liter approx. 75

10 kg kg

20

50

2 / 10

336 x 365

20

50

2 / 15

480 x 359

15

70

2 / 17

538 x 539 kg kg piece mm

Number

Dimensions

THERMAL

Operating temperatures Room temperature + 10 to 250

Temperature deviations

Spatial 1) at 70 °C at 150 °C at 250 °C

Temporal 1) at 70 °C at 150 °C at 250 °C

+ 3.0

+ 6.0

+ 7.0

+ 0.1

+ 0.1

+ 0.2

+ 3.0

+ 5.0

+ 6.0

+ 0.3

+ 0.5

+ 0.7

Warm-up times (unit empty, to 98 % of the operating temperature)

Operating temperature

70 °C

150 °C

45

50

50

55

250 °C 63 60

+ 3.0

+ 4.0

+ 5.0

+ 0.2

+ 0.3

+ 0.5

45

50

55

Unit

°C

K

K

K

K

K

K min min min

Cool-down times (unit empty, to 50 °C)

Operating temperature

250 °C

150 °C

302

218

70 °C 65 61

Recovery times (unit empty, door open 60 s, to 98 % of the operating temperature)

79

Operating temperature

70 °C

150 °C

250 °C

240

174

4

10

15

226

164

5

12

16

5

12

16

Heat radiation to surrounding areas (at a room temperature of 25 °C)

Operating temperature

70 °C

150 °C approx. 0.1

approx. 0.2

approx. 0.1

approx. 0.3

250 °C approx. 0.5

approx. 0.7

1) in accordance with DIN 12 880 Part 2 / 11.´78 approx. 0.1

approx. 0.4

approx. 0.8

min min min min min min kW kW kW

50 042 749 29

6 TECHNICAL DATA

DATA

VENTILATION

Air volume flow inside the chamber

Rate of air replacement

Exhaust air volume flow at 250 °C at 250 °C at 250 °C

Speed of exhaust air

Air outlet

∅ /

air inlet

Flue gas temperature at duct at 250 °C

Model

NOISE [in accordance with DIN 45 635]

Sound level [20 µPa]

Sound power level [1 pW]

T 6 P

0.58

8

0.58

0,13

40 / 20

250

T 12 P

1.31

10

1.31

0,29

40 / 20

250

T 20 P

1.17

5

1.17

0,26

40 / 20

250

Unit m h m m/s mm

°C

3

-1

3

/h

/h

The unit does not develop any internal noise

The unit does not develop any internal noise dB (A) dB

ELECTRICAL (rated values)

Rated voltage

Rated frequency

Power consumption

Connected load

Current input

Protection class

1.22

1.3

5.3

1/ PE AC, 230

50 / 60

1.82

1.9

7.9

I

2.22

2.4

9.7

V

Hz kW kVA

A

Protective measure

Degree of protection

PE terminal

IP 20

Circuit protection to be provided at the installation location 5)

T 16 A fusible link (slow-blow) or B 16 circuit-breaker

Connection via an earth-leakage circuit-breaker (tripping current

< 30 mA) is recommended.

ELECTRICAL (rated values)

Rated voltage

Rated frequency

Power consumption

Connected load

1/ PE AC, 120

1.3

1.3

10.8

1,49

1,5

1 / PE AC, 208

50 / 60

1,82

1,9

V

Hz kW kVA

A Current input

Protection class

Protective measure

7,1

I

PE terminal

8,8

Degree of protection

Circuit protection to be provided at the installation location 2)

IP 20

T 16 A fusible link (slow-blow) or B 16 circuit-breaker

Connection via an earth-leakage circuit-breaker (tripping current

< 30 mA) is recommended.

2) The applicable national electrical engineering regulations and technical requirements must be observed when connecting up to mains power supply circuits.

30 50 042 749

6 TECHNICAL DATA

Control unit

Reaction after power failure

(> 20 ms up to approx. 2 h) and return of power

Basic function

Control unit regulates on set temperature

Step to next program segment -

Display accuracy

(according to center of inner chamber)

Added-feature funtion Programmed function

Program will be stopped, inside temperature will be flashing displayed when set temperature is reached

< + 5 °C

Program will be continued at the last temperature/timevalues.

undepending on temperature

Component

Outer casing

Heat sink (rear panel)

Inner chamber

Components fitted in the chamber

Trays

Door seal

Door bearing

Door handle

Control unit

Switchgear unit

Operator control membrane

Feet

Thermal insulation

Filling medium - overtemp. protection device

Leads

Electronic / electrical components

Heating element

Materials used

Galvanized sheet steel, painted RAL 9002

Aluminium

Stainless steel, material No. 1.4301

Stainless steel, material No. 1.4301

Chromium-plated steel wire

Seasoned silicone rubber

PA, glass fiber reinforced

PA, glass fiber reinforced

ABS

PC, glass fiber reinforced

PVS, printed polyester foil

PPN

Mineral fiber wool

Polydimethyldisiloxane

PVC -sheathed copper wire

Encapsulated components coated with various plastics, some mounted on glass fiber reinforced

PCBs with epoxy resin

Stainless steel tubing filled with magnesium oxide and heating conductors

Fibrous materials used for insulation are classified as health hazards in some countries. Although the fibers which may be released into the environment during normal operation do not constitute a serious risk, greater, more hazardous quantities may be released as a result of improper handling during repair work or as a result of mechanical damage.

50 042 749 31

32

Model:

LOG BOOK

Please refer to typeplate on unit for model and serial number.

Serial No.:

Work completed Opearator´s remarks Date

33

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement