Carrier GAPAAXCC1625 Instruction manual

GAPAA
Infinity™ Air Purifier
Sizes 1625 and 2025
Installation Instructions
NOTE: Read the entire instruction manual before starting the
install.
TABLE OF CONTENTS
PAGE
INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
HOW IT WORKS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
SAFETY CONSIDERATIONS . . . . . . . . . . . . . . . . . . . . . . . . . 1
APPLICATION CONSIDERATIONS . . . . . . . . . . . . . . . . . . . . 2
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
START--UP AND OPERATION . . . . . . . . . . . . . . . . . . . . . . . . 6
MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
SPECIFICATIONS AND DIMENSIONS . . . . . . . . . . . . . . . . 10
WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
INTRODUCTION
Congratulations for selecting the Infinity Air Purifier for your
home comfort system! The Infinity Air Purifier is proven to
remove and kill airborne germs and allergens, including viruses,
bacteria, and mold spores. The Infinity Air Purifier is a cornerstone
of Carrier’s Healthy Home Solutions for providing healthier,
cleaner air in your home.
HOW IT WORKS
The Infinity Air Purifier provides extremely high filtration
performance while killing captured contaminants, including
viruses, bacteria, and mold spores. The Infinity Air Purifier treats
the entire air--stream through a state of the art, three--stage process.
In stage one, the particles are electrically charged by a
precision--point ionization array as they enter the Infinity Air
Purifier.
In stage two, the charged particles are electrically attracted to the air
purification cartridge, which is located within an electric field.
In stage three, captured particles are killed by electrical current
flow and ion bombardment.
The Infinity Air Purifier is CSA certified for shock and electrical
fire hazard only.
La Infinity Air Purifier certification CSA vise uniquement les
risques de choc electrique et.
A05265
Fig. 1 -- GAPAA Unit
SAFETY CONSIDERATIONS
Improper installation, adjustment, alteration, service, maintenance,
or use can cause explosion, fire, electrical shock, or other
conditions which may cause death, personal injury or property
damage. Consult a qualified installer, service agency or your
distributor or branch for information or assistance. The qualified
installer or agency must use factory--authorized kits or accessories
when modifying this product. Refer to the individual instructions
packaged with the kits or accessories when installing.
Follow all safety codes. Wear safety glasses, protective clothing,
and work gloves. Have a fire extinguisher available. Read these
instructions thoroughly and follow all warnings and cautions
included in literature and attached to the unit. Consult local
building codes and the current edition of the National Electrical
Code (NEC) NFPA 70.
In Canada, refer to the current editions of the Canadian Electrical
Code CSA C22.1.
on
Recognize safety information. When you see this symbol
the unit and in instructions or manuals, be alert to the potential for
personal injury. Understand the signal words DANGER,
WARNING, and CAUTION. These words are used with the
safety--alert symbol. DANGER identifies the most serious hazards,
which will result in severe personal injury or death. WARNING
signifies hazards, which could result in personal injury or death.
CAUTION is used to identify unsafe practices, which may result
in minor personal injury or product and property damage. NOTE
is used to highlight suggestions which will result in enhanced
installation, reliability, or operation.
APPLICATION CONSIDERATIONS
!
The Infinity Air Purifier is designed for use in the return air duct of
a forced air heating, cooling, and ventilation system. Models
GAPAAXCC1625 and GAPAAXCC2025 are specifically
designed for use in systems with a forced air gas furnace.
HIGH VOLTAGE HAZARD
Failure to follow this warning could result in personal injury
or death.
Air Conditioning
The Infinity Air Purifier should be installed in a system so that all
the return air is circulated through the air purifier. It should be
located upstream of both the furnace and the air conditioning
evaporator coil. This will help keep the furnace and evaporator coil
clean and prevent condensation from forming within the Infinity
Air Purifier.
GAPAA
Humidifiers
An evaporative humidifier can be mounted upstream of the Infinity
Air Purifier. It is best to install atomizing humidifiers downstream
of the air purifier because hard water salt deposits and water
droplets may damage air purifier. If an atomizing humidifier must
be mounted upstream of the Infinity Air Purifier, it should be
mounted as far upstream as possible (at least 6 ft./1.8 m
recommended), and a standard disposable furnace filter should be
mounted between the humidifier and the air purifier to trap hard
water salt deposits and water droplets.
Ensure that the humidifier installation will not allow water or water
droplets to enter the air purifier because it may cause electrical
arcing or damage the air purifier.
NOTE: For fan coil installations, do not install the humidifier in
the fan coil access doors or cabinet.
Inspect for plugged drains and maintain humidifier drain lines on a
regular basis to avoid overflow of water into the air purifier. The
recommended inspection should be done at every change of the air
purifier cartridge (minimum, annually).
Door (x1)
This air purifier utilizes high voltage. If you notice water
running into or around the air purifier, water stains on the
purifier cartridge or on the Enhancement Module walls or
cabinet, shut off the air purifier and call your service provider.
Transitions
If the return air duct or furnace openings do not fit the Infinity Air
Purifier cabinet openings, gradual transitions are recommended to
reduce air turbulence and maximize efficiency. No more than 45_
(about 8.5 in. per running ft.) of expansion should be used on each
side of the transition fitting.
Turning Vanes
If the Infinity Air Purifier is installed adjacent to a 90_ duct elbow,
turning vanes should be added inside duct to improve air
distribution across the face of the air purifier.
Electrical Power
The Infinity Air Purifier should only be powered when airflow is
present. The furnace control EAC terminals provide power only
when the furnace blower is operating. Infinity Air Purifier models
GAPAAXCC1625 and GAPAAXCC2025 are designed to be
powered from the electronic air cleaner (EAC) terminals on a
furnace electronic control. If EAC terminals are not available, an
alternative airflow sensing mechanism must be used to ensure the
Infinity Air Purifier is only powered when airflow is present.
Contact local Carrier distributor for information on approved
alternatives.
Air Purification Cartridge (x1)
Cabinet (x1)
WARNING
Enhancement Module (x1)
Safety Screen (x1)
(x1)
Furnace Adapters (x2)
(x2)
(x1)
(x2)
Duct Gasket Tape
(1 roll)
(x2)
Installation Components
(in bag attached to power cord)
Installation Manual
Return Duct Adapters:
Long (x2) / Short (x2)
A06027
Fig. 2 -- Infinity Air Purifier Components
2
INSTALLATION
cartridge and those on the sticker inside the cabinet. The
Infinity Air Purifier can be rotated 180_ to accommodate the cabinet orientation.
c. The location of the Infinity Air Purifier should be readily
accessible. Enough room should be provided for periodic
replacement of the air purifier cartridges.
Check Infinity Air Purifier Components
CAUTION
CUT HAZARD
!
Failure to follow this caution may result in personal injury.
Sheet metal parts may have sharp edges or burrs. Use care and
wear appropriate protective clothing and gloves when
handling parts.
WARNING
ELECTRIC SHOCK AND UNIT DAMAGE HAZARD
Failure to follow this warning could result in personal injury
or death.
Only a trained, experienced service person should install the
Infinity Air Purifier. A thorough check of the unit installation
should be completed before unit operation. Before performing
installation, service or maintenance operations on unit, turn off
all power to unit. Tag disconnect switch with lockout tag.
Carefully remove all items from the box.
Identify Mounting Location
a. Identify a mounting orientation for the Infinity Air Purifier
in the return air duct (see Figures 3 and 4).
IMPORTANT:
b. Ensure airflow direction through the Infinity Air Purifier matches the arrows on the face of the air purifier
NOTE:
Mounting on this side
requires the cabinet
to be rotated 180° for
correct air flow.
Airflow
Airflow
Airflow
Upflow Furnace with Side Return
Upflow Furnace with Bottom Mount
Downflow Furnace with Top Mount
Air flow
Horizontal Application
A06028
Fig. 3 -- Infinity Air Purifier Cabinet Orientation
3
GAPAA
!
Note: When transitioning between two different sized components (furnace & purfier), the
minimum transition angle at the larger of the two components must be no less than 45 degrees.
Upflow 14” Furnace
with Bottom Mount
Horizontal 14” Furnace
with Side Mount
Upflow Furnace
GAPAA
Downflow 14” Furnace
with Top Mount
Plenum
Box
Downflow 24” Furnace
with Top Mount
Upflow 24” Furnace On Stand
with Bottom Mount
Horizontal 24” Furnace
Upflow Furnace
with Plenum Box
A08608
Fig. 4 -- Infinity Air Purifier Cabinet Orientation with Transition
Return Duct
Adapters (x4)
Return Duc
t
Furnace
Adapters (x2)
Furnace
Adapters (x2)
Return Duct
Adapters (x4)
Return D
Top Mount
uct
Bottom Mount
Side Mount
A06029
Fig. 5 -- Mounting Infinity Air Purifier Cabinet
4
Mount Cabinet
!
g. Install foam tape between the furnace and the air purifier
cabinet.
h. Mounting holes are provided for ductwork and furnace attachment.
WARNING
ELECTRICAL SHOCK HAZARD
Failure to follow this warning could result in personal injury
or death.
Before installing or servicing system, always turn off main
power to system. There may be more than 1 disconnect switch.
CAUTION
!
Failure to follow this caution may result in equipment
damage.
Note: Slip
S-cleats onto flanges
on air return duct side.
Cabinets will support a maximum weight of 400 lbs/181 kg
when installed beneath a vertical furnace or air--handling
unit. When setting furnace on cabinet, do not drop it into
place. Position the furnace correctly on the cabinet to prevent
a corner from slipping down and damaging the cabinet or its
components.
a. Turn off power to the heating and cooling system.
b. Remove the existing furnace filter and discard. Excessive
system static may result if the Infinity Air Purifier is used
with other filtration devices.
c. Remove the air purifier cartridge and enhancement module
from the Infinity Air Purifier cabinet.
d. Position the cabinet between the furnace and return air duct
(see Figures 3, 4, 5 and 6). A transition duct may be required.
e. Furnace adapters have been included for installer convenience. They are designed for top or bottom mount installations (see Fig. 6).
Furnace
Adapters
GAPAA
UNIT DAMAGE HAZARD
A05277
Fig. 7 -- Use of Return Duct Adapters
CAUTION
!
UNIT DAMAGE HAZARD
Failure to follow this caution may result in unit damage.
Mounting holes are provided for duct work and furnace
attachment. The screws on the down--stream side of the
cabinet should be installed so that the screw heads are inside
air purifier cabinet to prevent damage to the air purifier
cartridge.
i. Seal seams with tape or caulking after the Infinity Air Purifier cabinet has been secured.
Special consideration must be given when applying the 2025 Air
Purifier to a 24 1/2--in (622 mm) wide furnace.
a. Prepare transition, following recommended transition drawing (see Fig. 8). Fabricate a 2 1/4--in (57 mm) tall (minimum) transition.
b. Place transition on top of Air Purifier. Secure with sheet
metal screws. Place furnace on top of transition. Make sure
furnace rests evenly on top of transition and Air Purifier.
c. Secure furnace to transition using sheet metal screws. See
Fig. 4.
d. Continue with normal installation practices.
Airflow
Furnace Casing Width 24 1/2” (622)
B
Rear Bracket
Sid
Airflow
eB
rac
ke
t
Sid
eB
rac
ke
5/8” (16)
Flanges
(Where Shown)
t
24” (610)
(Outside)
A05274
Fig. 6 -- Use of Furnace Adapters
2 1/4” (57)
Front Bracket
NOTE: Weld 3 places
in 4 corners
19 1/2” (495)
f. Return air duct adapters have been included for installer
convenience. They should be used to connect the upstream
side of the air purifier cabinet to the return air duct (see Fig.
7).
A
(Inside Opening)
Air Purifier Outlet
A09001
Fig. 8 -- Recommended Transition
5
Power Cord
to EAC Terminals
Sample Furnace Circuit Board
COM WW1 Y/Y2
24V
TEST/TWIN
PL T
HUM
Use terminals to connect the
power cord wires to the furnace
EAC-1 & 2, & ground terminals
ACRDJ
Power Supply
1 2 3
LHT
OFF
DLY
Y1 DHUM G
Power Supply Connector
Power Supply Connector
ON
OFF
W2
Use cable connector to secure
power cord to cabinet
0.5-AMP024 V AC
Power Cord
R
SEC-1
SEC-2
NEUTRAL-L2
PL3
OD E
EA C-2
PL1
US C
EAC-2 TERMINAL
Use wire ties to secure power cord
to power supply enclosure
LE D
FUSE 3-AMP
S TAT
1
1
BL W
BHI/LOR
BHT/CLR
BL WR
HI HEA T
IDM
PR-1
PL2
L1
EA C-1
1
SP ARE-2
IHI/LOR
HSIR
IDR
LO HEA T
1-AMP@115 V AC
COOL
SP ARE-1
HSI HI LO
GAPAA
Alternate Power Cord
Pass-Thru Hole
EAC-1 TERMINAL
A06030
Fig. 9 -- Infinity Air Purifier Electrical Connections
Wiring
!
!
WARNING
UNIT COMPONENT DAMAGE HAZARD
Failure to follow this caution may result in equipment
damage or improper operation.
ELECTRICAL SHOCK HAZARD
Failure to follow this warning could result in personal
injury or death.
Black Lead -- Connect to HOT (L1) or EAC--1 when
provided.
White Lead -- Connect to Neutral (L2) or EAC--2 when
provided.
Green/Ground Lead -- Connect to Appliance Ground
(Chassis).
Before installing or servicing system, always turn off main
power to system. There may be more than 1 disconnect
switch.
!
CAUTION
EQUIPMENT DAMAGE HAZARD
CAUTION
START--UP AND OPERATION
Checking Air Purifier Operation
!
Failure to follow this caution may result in equipment
damage or improper operation.
WARNING
ELECTRICAL SHOCK HAZARD
This unit cannot be powered directly from blower motor
leads. Voltages can exceed 190 VAC (120v motors). Do not
wire directly to blower motor. Wiring to blower motor will
damage power supply and void warranty.
Failure to follow this warning could result in personal injury
or death.
Before installing or servicing system, always turn off main
power to system. There may be more than one (1) disconnect
switch.
a. Ensure power has been removed from the heating and cooling system.
b. Turn the Infinity Air Purifier power switch off.
c. Connect the power cord to the power supply connector (see
Fig. 9).
d. Route the power cord through nearest cabinet hole and protect with enclosed cable connector. Zip ties have been enclosed to secure the power cord to the side of the power
supply.
e. Attach the quick connect terminals to the furnace EAC--1
and EAC--2 spade connections. Attach the ground ring to
furnace chassis ground.
NOTE: The Infinity Air Purifier is to be powered by 115v/60 Hz.
NOTE: The Infinity Air Purifier should only be powered when
airflow is present. The furnace control EAC spade connections
provide power only when the furnace blower is operating. If EAC
connections are not available, an alternative airflow sensing
mechanism must be used to ensure the Infinity Air Purifier is only
powered when airflow is present. Contact a local Carrier distributor
for information on approved alternatives.
a. Attach the Infinity Air Purifier door to the cabinet. A magnet in the door is used to activate a safety switch in the power supply when the door is installed. The power supply will
not energize the air purifier unless the safety switch is activated.
!
WARNING
CARBON MONOXIDE HAZARD
Failure to follow this warning could result in personal injury
or death.
Do not remove door during blower operation or operate
blower with door removed or improperly latched.
b. Turn the HVAC system power on and adjust the thermostat
or Infinity System Control to activate the system fan.
c. Turn the Infinity Air Purifier power switch to on position.
6
d. The power indicator light above the Air Purifier power
switch should illuminate (see Fig. 10).
e. Check to ensure the light goes off when the Infinity Air
Purifier power switch is set to off, when the blower goes off,
or when the HVAC system power is turned off.
!
WARNING
CARBON MONOXIDE HAZARD
Failure to follow this warning could result in personal injury
or death.
Infinity Control
Do not remove door during blower operation or operate
blower with door removed or improperly latched.
When the Infinity Air Purifier is used with an Infinity Control, the
Infinity Control can be configured to remind the homeowner when
it is time to change the Infinity Air Purifier cartridge. This
maintenance reminder can be based on either the TrueSenset dirty
filter algorithm or time. The installer should use their discretion to
select the most appropriate option based on the initial system static
pressure.
Maximizing Performance
Power Indicator
GAPAA
Maximum air purification performance is obtained when the
furnace blower is set for continuous operation on the thermostat or
Infinity Control.
MAINTENANCE
The Infinity Air Purifier is designed to require minimal
maintenance. Maintenance is limited to the periodic replacement of
the air purification cartridge and inspection/brush cleaning of the
ionization array. Frequency of air purifier cartridge replacement
and cleaning of the ionization array may vary depending on
ductwork design and local environmental conditions, generally
8--12 months.
!
WARNING
A06052
Fig. 10 -- Power Indicator
FIRE HAZARD
Failure to follow this warning could result in personal injury
or equipment damage.
Use of non--factory approved filter cartridge will void the
warranty and may cause damage due to fire.
At the time of air purifier cartridge replacement, if a powdery
residue is noticed on the tips of the points in the ionization array,
proceed to clean them by completing the following steps.
Turn heating and cooling system power off.
!
To replace the air purifier cartridge, complete the
following steps:
ELECTRICAL
HAZARD
Turn the heating and cooling system power
off.
!
AND
HIGH
VOLTAGE
Before installing or servicing system, always turn off main
power to system. There may be more than one (1) disconnect
switch.
ELECTRICAL SHOCK HAZARD
Failure to follow this warning could result in personal injury
or death.
Turn the Infinity Air Purifier switch to the off position.
Remove the Infinity Air Purifier door.
Slide out the old air purifier cartridge and discard.
Install the new air purifier cartridge. Make sure the power cord is
flexed out of the way to avoid damage to the air purifier cartridge
pleats during insertion.
NOTE: Verify that the air purifier cartridge is installed correctly.
Make sure that the arrows on the air purifier cartridge point toward
the furnace. This should be in the same direction as airflow and
match the arrows on the sticker inside the cabinet.
Replace the Infinity Air Purifier door.
Turn the Infinity Air Purifier switch to the on position.
Turn heating and cooling system power on.
SHOCK
Failure to follow this warning could result in personal injury
or death.
WARNING
Before installing or servicing system, always turn off main
power to system. There may be more than one (1) disconnect
switch.
WARNING
Turn the Infinity Air Purifier switch to the off position.
Remove the Infinity Air Purifier door.
Unplug the power cord from the enhancement module.
Slide out the enhancement module assembly and safety screen.
!
WARNING
CUT HAZARD
Failure to follow this warning could result in personal injury.
Sheet metal parts may have sharp edges or burrs. Use care and
wear appropriate protective clothing and gloves when
handling parts.
Slide out the Safety Screen and set aside.
NOTE: Best cleaning tools: 5--in (127 mm) handle paint brush
with 2--in (51 mm) width (or greater) brush point (synthetic or
7
Reinstall the Safety Screen. Do not operate the unit without the
Safety Screen
Slide in enhancement module.
Reconnect power cord.
Replace the Infinity Air Purifier door.
Turn the Infinity Air Purifier switch to the on position.
Turn heating and cooling system power on.
GAPAA
natural bristle) or vacuum cleaner with brush attachment. See Fig.
11.
Gently stroke the ionization pins on the top plane of each bar with
enough brush depth to hit front and back tips of the points in the
ionization array. Use a gentle back and forth brushing motion to
clean any small accumulations from the tips of the points. If
desired, use vacuum cleaner with brush attachment to gently
vacuum the frame and components of enhancement module. Also,
vacuum the safety screen to remove accumulated dust and debris.
30°
POINTS ARE SHARP! BE VERY CAREFUL DURING CLEANING.
Tip of point with residue
Tip of point after cleaning
A06671
Fig. 11 -- Removal of Deposits from Ionization Pins
TROUBLESHOOTING
!
CAUTION
SAFETY HAZARD
Failure to follow this caution may result in personal injury or
equipment damage.
The Infinity Air Purifier is equipped with a power indicator light
located on the door (see Fig. 10). This power indicator light will
illuminate when the Infinity Air Purifier door is installed, the
power switch is in the on position, AND the furnace blower is
running. If the power indicator light is not illuminated, follow the
troubleshooting steps below.
See Table 1.
The following instructions are for use by qualified personnel
only.
!
WARNING
ELECTRICAL SHOCK HAZARD
Failure to follow this warning could result in personal injury
or death.
The following procedures will expose electrical components.
Disconnect power between checks and proceed carefully. Only
a trained, experienced service person should install and/or
troubleshoot the Infinity Air Purifier.
8
Problem:
1
Infinity Air Purifier power indicator light
located on the door is off.
2
Power Indicator light cycles on and off
intermittently.
3
Air Purifier Cartridge has small singe or char
marks on the frame.
4
The wall control will not work.
5
The 20-minute lighted push- button switch
doesn’t work OR its indicator light doesn’t
stay on.
S Possible causes:
S You should try this:
S Power switch is not in the on (closed) position.
S Make sure the switch is on and using a
S Door is not closed. A magnet in the door is used
multimeter check to see that 115 Volt power is
to activate safety reed switches in the power
available.
supply when the door is installed.
S Re-cement loose door magnet with a suitable
S The door magnet is missing or has fallen out.
adhesive.
S If the unit switch is on and 115 Volt power is
available through the service cord, a door
magnet moved in close proximity of the power
S The door safety reed switches may be defective.
supply will cause the reed switches to audibly
click and the power supply will turn on.
S Furnace blower is not operating. Power will not
be supplied from the furnace control’s EAC S Make sure the furnace blower is operating.
terminals unless the blower is running.
S Replace Service cord or replace entire power
S Bent pins or loose connection in the molex plug
supply / field enhancement module assembly if
of the service cord.
required.
S Replace entire power supply / field enhancement
S The power supply may be defective.
module assembly.
S The light pipe transferring the light from the
LED’s on the power supply to the door may be S Replace access door.
broken.
S Overload condition activating the safety
S
circuitry
S Remove the access door and the air purifier
S Unit is wet. (Water may be entering the unit from
cartridge. Power the unit then use a spare door
magnet or “service” magnet to activate the air
a source such as condensate or dripping from a
frozen evaporator coil.)
purifier power supply. Turn out the lights and
observe for arcing.
S Make sure all three grounding clips (FEM to
S Grounding paths in the unit are interrupted due
cabinet, safety screen to cabinet, cartridge to
cabinet on the leaving air side) are securely in
to breakage , corrosion or loose contact.
place and making clean contact.
S Arcing to ground (such as unit cabinet ) is S Make sure the safety screen is clear and remove
occurring.
debris.
S Arcing to ground is occurring due to debris S Make sure the ionization grid is secured in place
lodged in the safety screen or across ionization
with all four clips and centered in the FEM
grid.
housing.
S Ionization grid is not centered or is loose and not
clipped in place, possibly touching the air S Verify that the ionization grid is clean and intact.
purifier cartridge or safety screen.
S Make sure the field electrode wire is wound
S Electrode wire is loose and making contact with
through the spools on the enhancement module
with sufficient tension and tied to itself at the end
the enhancement module wall.
termination. If it is loose rewind and retie it.
S If the field electrode wire is damaged or nicked,
replace entire power supply / field enhancement
S Field electrode wire is damaged or nicked.
module assembly.
S Turn off the unit and remove the access panel.
S Replace the air purifier cartridge with Factory
S The cartridge is installed backwards
Authorized Replacement Cartridge and ensure
airflow direction arrows are correct.
S Remove the wall control and test it right beside
S The wire in the wall OR the wall control may be
the unit using another shorter wire. If the wall
control works there, change the wire. If it does
defective.
not, change the wall control.
S Ensure that the color coded wires have been
S The wires may be in reverse position.
connected to their appropriate places.
S Inspect every wire and replace any that are
S The wires may be broken.
damaged.
S With the help of a multimeter, check for
S There may be a short-circuit.
continuity.
S Jump the OL and OC terminals. If the unit
switches to high speed, then the wires are not the
S The switch may be defective.
problem. Replace the push-button.
S The wires may be defective OR may not be S Ensure that the color-coded wires have been
connected properly.
connected to their appropriate places.
9
GAPAA
Be sure to inspect the unit before proceeding with these steps. Start with problem 1, then problem 2 and so on.
Table 1 – Troubleshooting
SPECIFICATIONS AND DIMENSIONS
Table 2 – Specifications and Dimensions
SPECIFICATIONS
Color
Cabinet Material
Electrical
GAPAAXCC2025
Taupe Metallic
Taupe Metallic
20 Ga. Powder Coated Steel
20 Ga. Powder Coated Steel
115v/60 Hz (from furnace EAC terminals)
115v/60 Hz (from furnace EAC terminals)
1600
2000
Maximum Airflow (CFM)
Efficiency
Replacement Cartridge
Pressure Drop @ Maximum Airflow
GAPAA
GAPAAXCC1625
MERV 15
MERV 15
GAPCCCAR1625
GAPCCCAR2025
.25 InH20
.25 InH20
Dimensions
GAPAAXCC1625
GAPAAXCC2025
A
18--- 3/8--- in (466.7mm)
21--- 7/8--- in (555.6mm)
B
15--- 1/8--- in (384.1mm)
18--- 5/8--- in (473.1mm)
C
11--- 1/8--- in (282.6mm)
11--- 1/8--- in (282.6mm)
D
17--- 1/2--- in (444.5mm)
21--- in (533.4mm)
E
22--1/8--in (562mm)
22--1/8--in (562mm)
F
25--- 1/4--- in (642.4mm)
25--- 1/4--- in (642.4mm)
1 3/16" (30.2mm)
A
B
D
7/16" (11.1mm) (Typical Top & Bottom)*
1 3/16˝ (30.2mm)
C
E
F
1 3/16˝ (30.2mm)
1 15/16˝ (49.2mm)
A09018
Fig. 12 -- Dimensions
10
Limited Warranty for Air Purifier
FOR WARRANTY SERVICE OR REPAIR:
Contact the installer. You may find the installer’s name on the equipment or in your Owner’s Packet.
For help, contact: CAC / BDP, Consumer Relations, P.O. Box 4808, Syracuse, New York 13221, Phone 1-800-227-7437
Model No. ____________________________________________
Unit Serial No. ________________________________________
Date of Installation _____________________________________
Installed by ___________________________________________
Name of Owner _______________________________________
Address of Installation __________________________________
CAC / BDP (hereinafter “Company”) warrants this product against failure due to defect in materials or workmanship under normal use and maintenance
as follows. All warranty periods begin on the date of original installation. If a part fails due to defect during the applicable warranty period Company
will provide a new or remanufactured part, at Company’s option, to replace the failed defective part at no charge for the part. Alternatively, and at its
option, the Company will allow a credit in the amount of the then factory selling price for a new equivalent part toward the retail purchase price of a new
Company product. Except as otherwise stated herein, those are Company’s exclusive obligations under this warranty for a product failure. This limited
warranty is subject to all provisions, conditions, limitations and exclusions listed below and on the reverse (if any) of this document.
OWNER-OCCUPIED, RESIDENTIAL APPLICATIONS
This warranty is to the original purchasing owner and is transferable only to the extent and as stated in the Warranty Conditions and below. The
warranty period in years, depending on the part and the claimant, is as shown in the chart below.
Limited Warranty (Years)
Product
Original Owner
Subsequent Owner
GAPA Air Purifier
10* ( or 5 )
1 0 * * (o r 5 )
* If properly registered within 90 days, otherwise 5 years (except in California and Quebec and other jurisdictions that prohibit warranty benefits
conditioned on registration, registration is not required to obtain longer warranty periods). See Warranty Conditions below.
** If properly transferred within 90 days, otherwise 5 years. See Warranty Conditions below. In California and Quebec and other jurisdictions that
prohibit warranty benefits conditioned on registration, registration is not required for a transfer and all warranty periods for subsequent owners are
five years from original installation.
OTHER RESIDENTIAL APPLICATIONS (Apartments, Rental Properties, etc.)
The warranty period is five (5) years and is not transferable.
OTHER APPLICATIONS
This warranty is non-transferable. The warranty period is one (1) year on all such applications.
LEGAL REMEDIES - The owner must notify the Company in writing, by certified or registered letter to CAC / BDP, Warranty Claims, P.O. Box 4808,
Syracuse, New York 13221, of any defect or complaint with the product, stating the defect or complaint and a specific request for repair, replacement,
or other correction of the product under warranty, mailed at least thirty (30) days before pursuing any legal rights or remedies.
39004DP452
01/10
11
GAPAA
PRODUCT REGISTRATION: You can register your product online at www.cac-bdp.com.
GAPAA
WARRANTY CONDITIONS:
1. To obtain the longer warranty periods as shown in the table under original owner, for the original purchaser, the product must be properly
registered at www.cac-bdp.com within ninety (90) days of original installation. In jurisdictions where warranty terms conditioned on
registration are prohibited by law, registration is not required and the longer warranty period shown will be apply.
2. Where a product is installed in a newly constructed home, the date of installation is the date the homeowner purchased the home from the
builder.
3. If the date of original installation cannot be verified, then the warranty period begins ninety (90) days from the date of product manufacture (as
indicated by the model and serial number). Proof of purchase may be required at time of service.
4. The remainder of the first five years of warranty is freely transferable without registration. To obtain a transfer of the longer warranty periods
as shown in the table under subsequent owner, a subsequent owner must register the transfer at www.cac-bdp.com within 90 days of the
change in ownership and payment of a transfer fee. Not applicable in all jurisdictions. See website for details.
5. Product must be installed properly and by a licensed HVAC technician.
6. The warranty applies only to products remaining in their original installation location.
7. Installation, use, care, and maintenance must be normal and in accordance with instructions contained in the Installation Instructions, Owner’s
Manual and Company’s service information.
8. Defective parts must be returned to the distributor through a registered servicing dealer for credit.
LIMITATIONS OF WARRANTIES:
ALL IMPLIED WARRANTIES AND/OR CONDITIONS (INCLUDING IMPLIED WARRANTIES OR
CONDITIONS OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR USE OR PURPOSE) ARE LIMITED TO THE DURATION OF THIS
LIMITED WARRANTY. SOME STATES OR PROVINCES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY OR
CONDITION LASTS, SO THE ABOVE MAY NOT APPLY TO YOU. THE EXPRESS WARRANTIES MADE IN THIS WARRANTY ARE
EXCLUSIVE AND MAY NOT BE ALTERED, ENLARGED, OR CHANGED BY ANY DISTRIBUTOR, DEALER, OR OTHER PERSON,
WHATSOEVER.
THIS WARRANTY DOES NOT COVER:
1. Labor or other costs incurred for diagnosing, repairing, removing, installing, shipping, servicing or handling of either defective parts, or
replacement parts, or new units.
2. Any product purchased over the Internet.
3. Normal maintenance as outlined in the installation and servicing instructions or Owner’s Manual, including filter cleaning and/or replacement
and lubrication.
4. Failure, damage or repairs from faulty installation, misapplication, abuse, improper servicing, unauthorized alteration or improper operation.
5. Failure to start due to voltage conditions, blown fuses, open circuit breakers, or damages due to the inadequacy or interruption of electrical
service.
6. Failure or damage due to floods, winds, fires, lightning, accidents, corrosive environments (rust, etc) or other conditions beyond the control of
Company.
7. Parts not supplied or designated by Company, or damages resulting from their use.
8. Products installed outside the U.S.A. or its territories and Canada.
9. Electricity or fuel costs, or increases in electricity or fuel costs from any reason whatsoever, including additional or unusual use of
supplemental electric heat.
10. Any cost to replace, refill or dispose of refrigerant, including the cost of refrigerant.
11. ANY SPECIAL, INDIRECT OR CONSEQUENTIAL PROPERTY OR COMMERCIAL DAMAGE OF ANY NATURE WHATSOEVER. Some
states or provinces do not allow the exclusion of incidental or consequential damages, so the above limitation may not apply to you.
This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state or province to province.
39004DP452
01/10
Copyright 2010 CAC / BDP D 7310 W. Morris St. D Indianapolis, IN 46231
Printed in China
Edition Date: 09/10
Manufacturer reserves the right to change, at any time, specifications and designs without notice and without obligations.
12
Catalog No: GAPAA ---06SI
Replaces: GAPAA--- 5SI