01EN_YSP-1_UB-cv1.fm Page 1 Friday, November 12, 2004 6:36 PM
UBTK
YSP-1
Digital Sound Projector
OWNER'S MANUAL
IMPORTANT SAFETY INSTRUCTIONS
1
Read these instructions.
2
Keep these instructions.
CAUTION
3
Heed all warnings.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
4
Follow all instructions.
5
Do not use this apparatus near water.
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
6
Clean only with dry cloth.
7
Do not block any ventilation openings. Install in accordance
with the manufacturer’s instructions.
8
Do not install near any heat sources such as radiators, heat
registers, stoves, or other apparatus (including amplifiers)
that produce heat.
* Explanation of Graphical Symbols
The lightning flash with arrowhead
symbol, within an equilateral triangle,
is intended to alert you to the presence
of uninsulated “dangerous voltage”
within the product’s enclosure that may
be of sufficient magnitude to constitute
a risk of electric shock to persons.
9
Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades with
one wider than the other. A grounding type plug has two
blades and a third grounding prong. The wide
blade or the third prong are provided for your safety. If the
provided plug does not fit into your outlet, consult an
electrician for replacement of the obsolete outlet.
The exclamation point within an
equilateral triangle is intended to alert
you to the presence of important
operating and maintenance (servicing)
instructions in the literature
accompanying the appliance.
10 Protect the power cable from being walked on or pinched
particularly at plugs, convenience receptacles, and the point
where they exit from the apparatus.
11 Only use attachments/accessories specified by the
manufacturer.
12 Use only with the cart, stand, tripod,
bracket, or table specified by the
manufacturer, or sold with the apparatus.
When a cart is used, use caution when
moving the cart/apparatus combination to
avoid injury from tip-over.
13 Unplug this apparatus during lightning storms or when
unused for long periods of time.
14 Refer all servicing to qualified service personnel. Servicing
is required when the apparatus has been damaged in any way,
such as power-supply cord or plug is damaged, liquid has
been spilled or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture, does not
operate normally, or has been dropped.
i CAUTION
IMPORTANT SAFETY INSTRUCTIONS
FCC INFORMATION (for US customers)
1. IMPORTANT NOTICE : DO NOT MODIFY THIS
UNIT!
This product, when installed as indicated in the instructions
contained in this manual, meets FCC requirements.
Modifications not expressly approved by Yamaha may void
your authority, granted by the FCC, to use the product.
Compliance with FCC regulations does not guarantee that
interference will not occur in all installations. If this product
is found to be the source of interference, which can be
determined by turning the unit “OFF” and “ON”, please try
to eliminate the problem by using one of the following
measures:
2. IMPORTANT :
When connecting this product to accessories and/or another
product use only high quality shielded cables. Cable/s
supplied with this product MUST be used. Follow all
installation instructions. Failure to follow instructions could
void your FCC authorization to use this product in the USA.
Relocate either this product or the device that is being
affected by the interference.
3. NOTE :
This product has been tested and found to comply with the
requirements listed in FCC Regulations, Part 15 for Class
“B” digital devices. Compliance with these requirements
provides a reasonable level of assurance that your use of this
product in a residential environment will not result in
harmful interference with other electronic devices.
This equipment generates/uses radio frequencies and, if not
installed and used according to the instructions found in the
users manual, may cause interference harmful to the
operation of other electronic devices.
Utilize power outlets that are on different branch (circuit
breaker or fuse) circuits or install AC line filter/s.
In the case of radio or TV interference, relocate/reorient the
antenna. If the antenna lead-in is 300 ohm ribbon lead,
change the lead-in to coaxial type cable.
If these corrective measures do not produce satisfactory
results, please contact the local retailer authorized to
distribute this type of product. If you can not locate the
appropriate retailer, please contact Yamaha Electronics
Corp., U.S.A. 6660 Orangethorpe Ave, Buena Park, CA
90620.
The above statements apply ONLY to those products
distributed by Yamaha Corporation of America or its
subsidiaries.
We Want You Listening For A Lifetime
YAMAHA and the Electronic Industries Association’s Consumer
Electronics Group want you to get the most out of your equipment by playing it at a safe level. One that lets the sound come
through loud and clear without annoying blaring or distortion –
and, most importantly, without affecting your sensitive hearing.
Since hearing damage from loud sounds is often
undetectable until it is too late, YAMAHA and the
Electronic Industries Association’s Consumer
Electronics Group recommend you to avoid prolonged exposure from excessive volume levels.
CAUTION ii
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
To assure the finest performance, please read this manual
carefully. Keep it in a safe place for future reference.
Install this sound system in a well ventilated, cool, dry, clean
place with at least 5 cm of space above (or below) YSP-1 – away
from direct sunlight, heat sources, vibration, dust, moisture, and/
or cold.
Locate this unit away from other electrical appliances, motors, or
transformers to avoid humming sounds.
Do not expose this unit to sudden temperature changes from cold
to hot, and do not locate this unit in an environment with high
humidity (i.e. a room with a humidifier) to prevent condensation
inside this unit, which may cause an electrical shock, fire,
damage to this unit, and/or personal injury.
Avoid installing this unit where foreign object may fall onto this
unit and/or this unit may be exposed to liquid dripping or
splashing. On the top of this unit, do not place:
– Other components, as they may cause damage and/or
discoloration on the surface of this unit.
– Burning objects (i.e. candles), as they may cause fire, damage
to this unit, and/or personal injury.
– Containers with liquid in them, as they may fall and liquid
may cause electrical shock to the user and/or damage to this
unit.
Do not cover this unit with a newspaper, tablecloth, curtain, etc.
in order not to obstruct heat radiation. If the temperature inside
this unit rises, it may cause fire, damage to this unit, and/or
personal injury.
Do not plug in this unit to a wall outlet until all connections are
complete.
Do not operate this unit upside-down. It may overheat, possibly
causing damage.
Do not use force on switches, knobs and/or cords.
When disconnecting the power cable from the wall outlet, grasp
the plug; do not pull the cable.
Do not clean this unit with chemical solvents; this might damage
the finish. Use a clean, dry cloth.
Only voltage specified on this unit must be used. Using this unit
with a higher voltage than specified is dangerous and may cause
fire, damage to this unit, and/or personal injury. YAMAHA will
not be held responsible for any damage resulting from use of this
unit with a voltage other than specified.
To prevent damage by lightning, disconnect the power cable from
the wall outlet during an electrical storm.
Do not attempt to modify or fix this unit. Contact qualified
YAMAHA service personnel when any service is needed.
The cabinet should never be opened for any reasons.
When not planning to use this unit for long periods of time (i.e.
vacation), disconnect the AC power plug from the wall outlet.
Be sure to read the “TROUBLESHOOTING” section on
common operating errors before concluding that this unit is
faulty.
Before moving this unit, press STANDBY/ON to set this unit in
standby mode, and disconnect the AC power plug from the wall
outlet.
Condensation will form when the surrounding temperature
changes suddenly. Disconnect the power cable from the outlet,
then leave the unit alone.
When using the unit for a long time, the unit may become warm.
Turn the power off, then leave the unit alone for cooling.
iii CAUTION
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THIS APPLIANCE TO RAIN OR
MOISTURE.
This unit is not disconnected from the AC power source as
long as it is connected to the wall outlet, even if this unit itself
is turned off. This state is called the standby mode. In this
state, this unit is designed to consume a very small quantity of
power.
FOR CANADIAN CUSTOMERS
To prevent electric shock, match wide blade of plug to wide
slot and fully insert.
This Class B digital apparatus complies with Canadian
ICES-003.
IMPORTANT
Please record the serial number of this unit in the space
below.
MODEL:
Serial No.:
The serial number is located on the rear or the bottom of
this unit.
Retain this Owner’s Manual in a safe place for future
reference.
■ For U.K. customers
If the socket outlets in the home are not suitable for the plug
supplied with this appliance, it should be cut off and an
appropriate 3 pin plug fitted. For details, refer to the instructions
described below.
Note
The plug severed from the mains lead must be destroyed, as a
plug with bared flexible cord is hazardous if engaged in a live
socket outlet.
■ Special instructions for U.K. model
IMPORTANT
THE WIRES IN MAINS LEAD ARE COLOURED IN
ACCORDANCE WITH THE FOLLOWING CODE:
Blue: NEUTRAL
Brown: LIVE
As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings
identifying the terminals in your plug, proceed as follows:
The wire which is coloured BLUE must be connected to
the terminal which is marked with the letter N or coloured
BLACK. The wire which is coloured BROWN must be
connected to the terminal which is marked with the letter L
or coloured RED.
Making sure that neither core is connected to the earth
terminal of the three pin plug.
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous
radiation exposure.
CAUTION iv
HOW TO USE THIS MANUAL
Check that you have received all of the supplied accessories.
(See “Supplied accessories” on page 4.)
Install this unit in your listening room.
(See “INSTALLING THIS UNIT IN YOUR LISTENING ROOM” on page 9.)
Connect this unit to your TV and other external components.
(See “CONNECTIONS” on page 11.)
Prepare the remote control and turn on this unit.
(See “PREPARING THE REMOTE CONTROL” on page 18 and “BASIC OPERATION” on page 19.)
Follow the steps to enjoying surround sound or make EASY SETUP settings.
(See “STEPS TO ENJOYING SURROUND SOUND” on page 20 or “EASY SETUP” on page 24.)
Play back a source and adjust the beam mode settings.
(See “PLAYBACK” on page 31 and “ADJUSTING BEAM MODE SETTINGS” on page 34.)
To make additional settings and adjustments:
Make MANUAL SETUP settings and set remote control codes.
(See “MANUAL SETUP” on page 36 and “REMOTE CONTROL FEATURES” on page 51.)
v
CONTENTS
ADVANCED OPERATION
OVERVIEW ........................................................... 2
MANUAL SETUP.................................................36
Selecting a listening room ......................................... 4
About this manual...................................................... 4
Supplied accessories .................................................. 4
Using SET MENU................................................... 37
SOUND MENU....................................................... 38
BEAM MENU ......................................................... 40
INPUT MENU......................................................... 44
OPTION MENU...................................................... 45
CONTROLS AND FUNCTIONS ......................... 5
PREPARATION
INSTALLING THIS UNIT IN YOUR
LISTENING ROOM .......................................... 9
CONNECTIONS .................................................. 11
USING THE SLEEP TIMER ..............................50
ADDITIONAL INFORMATION
REMOTE CONTROL FEATURES ...................51
Setting remote control codes ................................... 51
Controlling other components ................................. 52
TROUBLESHOOTING .......................................54
RESETTING THE FACTORY PRESETS ........57
FRONT PANEL DISPLAY ITEMS....................58
GLOSSARY...........................................................59
Audio formats .......................................................... 59
Audio information ................................................... 59
INDEX ....................................................................60
SPECIFICATIONS...............................................61
ADVANCED
OPERATION
Connecting a TV...................................................... 12
Connecting a DVD player/recorder ......................... 13
Connecting a VCR................................................... 14
Connecting other external components ................... 15
Connecting a subwoofer .......................................... 16
Connecting the power supply cable......................... 17
About the RS-232C terminal ................................... 17
Using the test tone ................................................... 48
Adjusting output levels during playback ................. 49
BASIC
OPERATION
Choosing an installation location............................... 9
Using a metal wall bracket ...................................... 10
Using a stand............................................................ 10
Using a rack ............................................................. 10
Affixing this unit...................................................... 10
SELECTING AN INPUT MODE........................47
MANUALLY ADJUSTING OUTPUT
LEVELS .............................................................48
PREPARATION
Front panel ................................................................. 5
Front panel display .................................................... 6
Bottom panel.............................................................. 7
Remote control........................................................... 8
INTRODUCTION
INTRODUCTION
BASIC OPERATION
PREPARING THE REMOTE CONTROL ....... 18
Installing batteries in the remote control ................. 18
BASIC OPERATION........................................... 19
Using the remote control ......................................... 19
Turning the power on/to standby mode ................... 19
ADDITIONAL
INFORMATION
STEPS TO ENJOYING SURROUND
SOUND .................................................................. 20
Displaying the on-screen display (OSD) ................. 20
Selecting a preset listening environment ................. 21
Enjoying TV in surround sound .............................. 22
EASY SETUP........................................................ 24
Using EASY SETUP ............................................... 24
VOLUME CONTROLS....................................... 30
Adjusting the volume............................................... 30
Muting the sound ..................................................... 30
PLAYBACK.......................................................... 31
Selecting an input source ......................................... 31
Playing back sources................................................ 31
SELECTING A SURROUND MODE................ 32
Playback sources and their available surround
modes................................................................... 32
Enjoying 2-channel sources with multi channels .... 32
Surround mode parameters ...................................... 33
ADDITIONAL PLAYBACK MODES ............... 33
Night listening modes .............................................. 33
ADJUSTING BEAM MODE SETTINGS.......... 34
Stereo mode ............................................................. 34
3 beam mode............................................................ 34
5 beam mode............................................................ 34
ST(STEREO)+3 beam mode ................................... 35
1
OVERVIEW
OVERVIEW
It is generally accepted that in order to fully enjoy the benefits of surround sound at home, you must endure the agony of
wiring and installing a great number of speakers in the hope that your listening room will give you the same kind of
surround sound experience as your local movie theater.
YAMAHA’s YSP-1 Digital Sound Projector challenges this preconception that complicated speaker set up and
troublesome wiring go hand-in-hand with the enjoyment of multi-channel surround sound.
Sound Beam Diagram
C
L
R
Listening
Position
SL
Imaginary front speaker position
Imaginary surround speaker position
2
SR
OVERVIEW
The YSP-1 projects sound beams containing surround sound information for the front right (R), front left (L), surround
right (SR) and surround left (SL) speaker positions, which are reflected off the walls of your listening room before
reaching the actual listening position. With the addition of center (C) sound beams, this Digital Sound Projector creates
true-to-life 5.1 channel surround sound that makes you feel as if there are actual speakers around the room.
Further, you can change the way in which these beams are projected at your walls (the beam mode) to match the contents
of the program you are watching or your listening environment, giving you a virtual surround sound experience for both
stereo and 5.1-channel playback.
This unit’s SET MENU can be displayed on your TV screen, allowing you to customize this unit to suit your listening
environment. Set up is straight forward using the MEMORY or EASY SETUP menus. MEMORY allows you to load
preset listening environment parameters for quick setup. EASY SETUP is an easy-to-follow setup method for first-time
users. In addition, the MANUAL SETUP menu offers advanced parameters for the surround sound enthusiast who wants
to make individual adjustments for each speaker position.
This highly-advanced projector supports a wide range of sound technology, including Dolby Digital, a basic audio format
for DVDs, Dolby Pro Logic for the reproduction of true-to-life sound, and DTS for playback of the best possible sound
clarity.
Equipped with two optical digital, one coaxial digital and two analog input jacks, the YSP-1 allows you to expand your
system through the direct connection of external components, such as a DVD player.
Sit back and enjoy the real sound experience of this simple, yet stylish Digital Sound Projector.
3
INTRODUCTION
This slimline unit does away with the need for complicated wiring and installation worries, leaving you with a unit that is
not only easy to set up, but which is also capable of reproducing the kind of powerful surround sound you have been
waiting for from its built-in subwoofers (2) and individual speakers (40).
You can use this unit’s parameters to fine tune the delay time for separate sound beams, resulting in highly directional
sound that comes in on the listening position from all directions.
OVERVIEW
Selecting a listening room
This unit creates surround sound by reflecting projected sound beams off the walls of your listening room. The surround
sound effects produced by this unit may not be sufficient when the unit is installed in the following locations:
• Rooms with surfaces inadequate for reflecting sound beams
• Rooms with acoustically absorbent surfaces
• Rooms with measurements outside the range: (3 to 7 m) × (2 to 3.5 m) × (3 to 7 m) (W × H × D)
• Rooms with less than 2 m from the listening position to the speaker positions
• Rooms where objects such as furniture are likely to obstruct the path of sound beams
About this manual
• This manual describes how to connect and operate the YSP-1. For details regarding the operation of external
components, refer to the supplied owner’s manual for the component.
• Some operations can be performed by using either the buttons on the main unit or on the remote control. In such cases,
the operation is described using remote control operation.
• y indicates a tip for your operation.
• This manual is printed prior to production. Design and specifications are subject to change in part as a result of
improvements, etc. In case of differences between the manual and product, the product has priority.
Manufactured under license from Dolby Laboratories.
“Dolby”, “Pro Logic”, and the double-D symbol are trademarks
of Dolby Laboratories.
Manufactured under license from 1 Ltd. world-wide patents
applied for.
The “
1 Ltd.
” logo and “Digital Sound Projector” are trademarks of
“DTS”, and “Neo:6” are trademarks of Digital Theater Systems,
Inc.
Supplied accessories
Please check that you received all of the following parts.
Remote control (×1)
STANDBY/ON
Batteries (×2)
(AA, R6, UM-3)
OSD Video Cable (×1)
Optical Cable (×1)
POWER
AV
1
2
3
5
6
7
9
0
+10
4
8
CODE SET
Digital Audio Pin Cable (×1)
CH
Cable Holder (×1)
NIGHT
SURROUND
CH LEVEL
SET MENU
MENU
Power Cable (×1)
SELECT
RETURN
TEST
VOLUME
TV VOL
MUTE
Audio Pin Cable (×1)
TV MUTE
TV INPUT
SLEEP
TV
DVD
AUX
VCR
BEAM MODE
4
Fastener (×4)
CONTROLS AND FUNCTIONS
CONTROLS AND FUNCTIONS
INTRODUCTION
Front panel
1
1 Front panel display
Shows information about the operational status of this
unit.
2 Remote control sensor
Receives signals from the remote control.
3 INPUT
Switches between the connected external audio sources.
4 VOLUME –/+
Controls the output level of all audio channels (see
page 30).
2
INPUT
VOLUME
3
4
+
STANDBY/ON
5
5 STANDBY/ON
Turns on this unit or sets it in the standby mode (see
page 19). When you turn on this unit, you will hear a click
and there will be a 4 to 5-second delay before it can
reproduce sound.
Note
In standby mode, this unit consumes a small amount of power in
order to receive infrared-signals from the remote control.
5
CONTROLS AND FUNCTIONS
Front panel display
1
2
NIGHT
SLEEP
3
PCM
4
DIGITAL
PL
VOL
m
ft
mS
dB
5
1 NIGHT indicator
Lights up when you select a night listening mode (see
page 33).
2 SLEEP indicator
Lights up while the sleep timer is on (see page 50).
3 Decoder indicators
When any of this unit’s decoders function, the respective
indicator lights up.
6
4 Volume level indication
Indicates the current volume level (see page 30).
5 Multi-information display
Shows information when adjusting or changing settings.
CONTROLS AND FUNCTIONS
Bottom panel
RS-232C
1
2
3
4
5
INTRODUCTION
SYSTEM
CONNECTOR
DIGITAL INPUT
DVD
AUX
TV
COAXIAL OPTICAL
AUDIO INPUT
VIDEO SUBWOOFER
TV
VCR
R
L
R
L
OUT
OUT
6
7
9
8
0
1 SYSTEM CONNECTOR jack
Use to connect a YAMAHA subwoofer equipped with a
SYSTEM CONNECTOR jack to this unit (see page 16).
6 VIDEO OUT jack
Connect to your TV’s video input terminal to display this
unit’s OSD (see page 12).
2 RS-232C terminal
This is a control expansion terminal for commercial use
only (see page 17).
7 SUBWOOFER OUT jack
Use to connect a subwoofer (see page 16).
3 DVD coaxial digital input jack
Use to connect a DVD player using a coaxial digital
connection (see page 13).
4 AUX optical digital input jack
Use to connect an external component using an optical
digital connection (see page 15).
5 TV optical digital input jack
Use to connect a TV using an optical digital connection
(see page 12).
8 TV analog audio input jacks
Use to make an analog connection to your TV
(see page 12).
9 VCR analog audio input jacks
Use to make an analog connection to your VCR
(see page 14).
0 AC IN
Connect the supplied power cable (see page 17).
7
CONTROLS AND FUNCTIONS
Remote control
This section describes the function of each control on the
remote control used to control this system. To operate
other components, see “Controlling other components” on
page 52.
1
STANDBY/ON
POWER
4 NIGHT
Turns on or off the night listening modes (see page 33).
AV
1
2
3
4
5
6
7
8
9
0
+10
CODE SET
5 SURROUND
Selects the surround mode for playback (see page 32).
A
CH
4
5
NIGHT
SURROUND
CH LEVEL
SET MENU
MENU
RETURN
TEST
C
0 Beam mode buttons
Change the beam mode settings (see page 34).
D
A CODE SET
Use to set up remote control codes (see page 51).
VOLUME
MUTE
TV MUTE
9
TV INPUT
SLEEP
TV
AUX
BEAM MODE
0
8 MUTE
Mutes the sound (see page 30). Press again to restore the
audio output to the previous volume level.
9 SLEEP
Sets the sleep timer (see page 50).
SELECT
TV VOL
8
6 Cursor buttons
/
/ / SELECT
Use to select and adjust SET MENU items.
7 TEST
Outputs a test tone when adjusting the speaker levels
(see page 48).
B
6
7
2 STANDBY/ON
Sets this system in the standby mode (see page 19).
3 Numeric buttons
Use to enter numbers.
2
3
1 Infrared window
Outputs infrared control signals. Aim this window at the
component you want to operate.
DVD
VCR
E
B SET MENU
Displays the SET MENU on your TV or monitor
(see page 24).
C RETURN
Use to select sleep timer settings (see page 50) or return to
the previous SET MENU screen (see page 24).
D VOLUME +/–
Increases or decreases this system’s volume level
(see page 30).
E Input selector buttons
Use to select a playback source and change the control
area (see page 31).
8
INSTALLING THIS UNIT IN YOUR LISTENING ROOM
INSTALLING THIS UNIT IN YOUR LISTENING ROOM
This section describes how to choose a suitable installation location for this unit, and how to install the unit using either a
metal wall bracket, rack or stand.
Note
If objects such as furniture are obstructing the path of sound beams, the desired surround sound effects may not be achieved. Make sure
you install this unit where there are no objects in the path of sound beams.
■ Notes on installation
PREPARATION
• When installing this unit, be sure to leave an adequate
amount of ventilation space so that heat can escape.
Make sure you leave at least 5 cm of space above
(or below) this unit (as shown in the illustration on the
right).
• We do not recommend installing this unit so that it is
positioned directly on the floor of your listening room.
Please install this unit using a metal wall bracket, rack
or stand.
• This unit weighs 13 kg (28lbs). Be sure to install this
unit where it will not fall if subject to vibrations, such
as from an earthquake, and where it is out of the reach
of children.
• When using a cathode-ray tube (CRT) TV, do not
install this unit directly above your TV.
• This unit is shielded against magnetic rays. However,
if the picture on your TV screen becomes blurred or
distorted, we recommend moving the speakers away
from your TV.
5 cm or
more
Front
Rear
Choosing an installation location
To experience the best surround sound this unit can deliver, make sure you install this unit in a location where objects,
such as furniture, are not in the direct path of the sound beams (see the illustration below).
When installing this unit parallel to the wall, try placing it so that it is in the exact center of the wall (measured from the
left and right corners).
When installing this unit in the corner of your listening room, make sure the speakers are placed between 40º to 50º from
the adjacent walls.
An object, such as furniture
40° to 50°
9
INSTALLING THIS UNIT IN YOUR LISTENING ROOM
Using a metal wall bracket
Using a rack
You can use the optional metal wall bracket to mount this
system on your listening room wall.
You can install this system either above or under your TV
in a commercially available rack.
For details on how to attach the metal bracket to the wall
or how to attach this system to the metal bracket, refer to
the instructions supplied with the bracket.
Before installing, make sure that the rack is large enough
to allow adequate ventilation space around this unit, and
that it is strong enough to support the weight of both this
unit and your TV.
Metal wall bracket
When the YSP-1 is
installed above your TV
YSP-1
TV
TV
Using a stand
You can mount your TV on the stand placed on a
commercially available rack to install this unit under your
TV.
For details on how to attach the stand or how to attach this
system to your TV, refer to the instructions supplied with
the stand.
Stand
TV
When the YSP-1 is
installed under your TV
Affixing this unit
To affix this unit, remove the protection pads from the
bottom of the unit, then secure the supplied fasteners (4
pieces) to the bottom four corners of this unit and the top
of the rack, etc. as shown below.
Notes
• Do not install this unit on top of a slanted surface. This unit may
fall over and cause injury.
• Make sure you wipe the surface of the rack, etc. before securing
the fasteners. Appling the tape to a dirty or wet surface will
weaken the sticking power of the tape, and this unit may fall as
a result.
YSP-1
YSP-1
Remove the
protection
pads
Peel off
the film
Fasteners
10
CONNECTIONS
CONNECTIONS
This unit is equipped with two optical digital jacks, one coaxial digital jack and two types of analog jacks for connecting
external components such as your TV, DVD player, VCR and game console. Further, by connecting a subwoofer to this
unit, you can enjoy reinforced low bass sounds. For details on how to connect the various types of external components to
this unit, see pages 12 to 17.
CAUTION
Do not connect this unit or other components to the mains power until all connections between components are complete.
Audio connection
PREPARATION
Video connection
TV
YSP-1
DVD player
Subwoofer
VCR
Digital satellite tuner, cable TV or
game console
11
CONNECTIONS
Connecting a TV
You can connect a TV to this unit and display the OSD for easy viewing (see page 20) when operating SET MENU (see
page 24). When connecting the Optical Cable, use the Cable Holder at the rear panel of the YSP-1 to fix the cable (see
page 15).
Cables used for connections
For digital connections
For video (OSD) connections
OSD Video Cable (supplied)
Audio Pin Cable (supplied)
(White)
(White)
(Red)
(Red)
Optical Cable (supplied)
■ Digital and analog connections
■ Video (OSD) connections
YSP-1 (Bottom panel)
SYSTEM
CONNECTOR
RS-232C
DIGITAL INPUT
DVD
AUX
TV
COAXIAL OPTICAL
AUDIO INPUT
VIDEO SUBWOOFER
TV
VCR
OUT
OUT
R
L
R
L
Analog audio
Optical digital output
output
R
L
TV
12
YSP-1 (Bottom panel)
SYSTEM
CONNECTOR
RS-232C
AUDIO INPUT
VIDEO SUBWOOFER
TV
VCR
OUT
OUT
R
L
R
L
DIGITAL INPUT
DVD
AUX
TV
COAXIAL OPTICAL
Video
input
TV
CONNECTIONS
Connecting a DVD player/recorder
To connect a DVD player/recorder, connect the coaxial digital output jack on your DVD player to the coaxial digital
input jack (DVD COAXIAL) on this unit.
If there is no coaxial digital output jack on your DVD player/recorder, use them with optical digital connection.
Cables used for connections
Digital Audio Pin Cable (supplied)
PREPARATION
YSP-1 (Bottom panel)
SYSTEM
CONNECTOR
RS-232C
DIGITAL INPUT
DVD
AUX
TV
COAXIAL OPTICAL
AUDIO INPUT
VIDEO SUBWOOFER
TV
VCR
R
L
R
L
OUT
OUT
Coaxial digital
output
Video signal
to a TV
DVD player/recorder
13
CONNECTIONS
Connecting a VCR
To connect a VCR, connect the analog audio output jack on your VCR to the analog audio input jack (VCR R/L) on this
unit.
Connect red plugs to the right jacks and white plugs to the left jacks.
Cables used for connections
Audio Pin Cable
(White)
(White)
(Red)
(Red)
YSP-1 (Bottom panel)
SYSTEM
CONNECTOR
RS-232C
AUDIO INPUT
VIDEO SUBWOOFER
TV
VCR
R
L
R
L
OUT
OUT
DIGITAL INPUT
DVD
AUX
TV
COAXIAL OPTICAL
(Red)
(White)
(White)
(Red)
Analog audio
output
R
L
Video signal
to a TV
VCR
14
CONNECTIONS
Connecting other external components
To connect other external components, connect the optical digital output jack on the component to the optical digital
input jack (AUX OPTICAL) on this unit.
You can connect a DVD player/recorder or a component that supports optical digital connections.
Cables used for connections
Optical Cable
PREPARATION
YSP-1 (Bottom panel)
SYSTEM
CONNECTOR
RS-232C
DIGITAL INPUT
DVD
AUX
TV
COAXIAL OPTICAL
AUDIO INPUT
VIDEO SUBWOOFER
TV
VCR
R
L
R
L
OUT
OUT
To prevent cables from becoming
unplugged, place the cable holder
provided open side up, and attach
it to the rear panel of this unit in a
suitable position. Affix the
cable(s) in the holder.
Optical fiber
cable
Attach to
the YSP-1
Optical digital
output
Video signal
to a TV
Digital satellite tuner, cable TV or
game console
15
CONNECTIONS
Connecting a subwoofer
To connect a subwoofer, connect the monaural input jack on your subwoofer to the monaural audio output jack
(SUBWOOFER OUT) on this unit.
When connecting a YAMAHA subwoofer equipped with a SYSTEM CONNECTOR jack, connect it to the SYSTEM
CONNECTOR jack on this unit. If the subwoofer is connected using a system type connection, changing the power mode
of this unit controls the power mode of the subwoofer.
To adjust the settings for your subwoofer, see SUBWOOFER SET in MANUAL SETUP (page 38).
Cables used for connections
Subwoofer pin cable
YSP-1 (Bottom panel)
SYSTEM
CONNECTOR
RS-232C
DIGITAL INPUT
DVD
AUX
TV
COAXIAL OPTICAL
AUDIO INPUT
VIDEO SUBWOOFER
TV
VCR
R
L
R
L
OUT
OUT
System Monaural
input
connector
Subwoofer
16
CONNECTIONS
Connecting the power supply cable
■ Connecting the AC power cable
Once all other connections are complete, plug one end of the power cable into the AC IN terminal on this unit, then plug
the other end into an AC wall outlet.
To an AC outlet
PREPARATION
About the RS-232C terminal
The RS-232C terminal on the bottom panel of this unit does not support normal external component connection.
This is a control expansion terminal for commercial use only.
YSP-1 (Bottom panel)
SYSTEM
CONNECTOR
RS-232C
DIGITAL INPUT
DVD
AUX
TV
COAXIAL OPTICAL
AUDIO INPUT
VIDEO SUBWOOFER
TV
VCR
R
L
R
L
OUT
OUT
RS-232C terminal
17
PREPARING THE REMOTE CONTROL
PREPARING THE REMOTE CONTROL
Installing batteries in the remote
control
Press %
1
Press the
mark on the battery cover and
slide off the cover.
2
Insert the two supplied batteries (AA, R06,
UM-3) into the battery compartment.
Make sure you insert the batteries according to the
polarity markings (+/–).
3
Close the battery cover.
18
Notes on batteries
• Change all of the batteries if you notice the following
conditions; the operation range of the remote control
decreases, the indicator does not blink or its light
becomes dim.
• Do not use old batteries together with new ones.
• Do not use different types of batteries (such as alkaline
and manganese batteries) together. Read the packaging
carefully as these different types of batteries may have
the same shape and color.
• If the batteries have leaked, dispose of them
immediately. Avoid touching the leaked material or
letting it come into contact with clothing, etc. Clean the
battery compartment thoroughly before installing new
batteries.
If the remote control is without batteries for more than
2 minutes, or if exhausted batteries remain in the
remote control, the contents of the memory may be
cleared. When the memory is cleared, insert new
batteries and reset the remote control codes.
When changing the batteries, be careful not to press
any of the buttons on the remote control.
Doing so will clear the contents of the memory.
BASIC OPERATION
BASIC OPERATION
Using the remote control
The remote control transmits a directional infrared beam.
Use the remote control within 6 m (20 feet) of this unit
and point it toward the remote control sensor on the main
unit during operation.
Approximately
6 m (20 ft)
30˚
Turning the power on/to standby
mode
INPUT
VOLUME
+
STANDBY/ON
30˚
STANDBY/ON
BASIC
OPERATION
or
POWER
AV
■ Handling the remote control
• Do not spill water or other liquids on the remote
control.
• Do not drop the remote control.
• Do not leave or store the remote control in the
following types of conditions:
– places of high humidity, such as near a bath
– high temperatures, such as near a heater or stove
– extremely low temperatures
– dusty places
• Do not expose the remote control sensor on the main
unit to direct sunlight or lighting (inverted fluorescent
lamps).
• If the batteries grow old, the effective operation
distance of the remote control decreases considerably.
If this happens, replace the batteries with two new ones
as soon as possible.
1
2
3
4
5
6
7
8
Press STANDBY/ON on the front panel or the
remote control to turn this unit’s power on/to
standby mode.
This unit’s power switches between on and standby mode
each time STANDBY/ON is pressed.
STANDBY/ON
or
Front panel
Remote control
19
STEPS TO ENJOYING SURROUND SOUND
STEPS TO ENJOYING SURROUND SOUND
This section describes very simply how to display this unit’s OSD on your TV screen and set the parameters for your
listening room. Once this is complete, you can enjoy real surround sound while watching TV in the comfort of your own
home.
Displaying the on-screen display
(OSD)
Connect the video input jack on your TV to the VIDEO
OUT jack on this unit to display this unit’s OSD.
1
Press STANDBY/ON on the remote control.
This unit’s power is turned on.
2
Turn on the power to your TV.
3
Press TV to display this unit’s OSD on your
TV screen.
It may take a few seconds before this unit’s OSD
appears on your TV screen.
If the OSD does not appear, use the remote control
provided with your TV to switch the video input until
the OSD appears.
■ Other buttons that display the OSD
Remote control buttons that
display the OSD
1 NIGHT
33
2 SURROUND
32
3 CH LEVEL
49
4 Cursor buttons
–
5 TEST
48
6 MUTE
30
7 SLEEP
50
8 BEAM MODE
34
9 SET MENU
24
0 VOLUME +/–
30
A Input selector buttons
31
1
2
3
NIGHT
SURROUND
CH LEVEL
4
5
TV
Page
SET MENU
9
MENU
SELECT
RETURN
TEST
VOLUME
TV VOL
MUTE
0
TV MUTE
INPUT
TV
AUTO:ANALOG
OSD screen example
6
7
TV INPUT
TV
DVD
SLEEP
AUX
VCR
BEAM MODE
8
20
A
STEPS TO ENJOYING SURROUND SOUND
Selecting a preset listening
environment
1
For real surround sound, select the preset listening room
type (see below) that best matches your own listening
environment.
If none of the selections available are suitable for your
listening environment, proceed to EASY SETUP
(page 24) to make your own listening environment
settings.
Press SET MENU.
The SET MENU screen appears on your TV.
The operation buttons for SET MENU are displayed
at the bottom of the screen.
SET MENU
SET MENU
.;MEMORY
;EASY SETUP
;MANUAL SETUP
p
p
[]/[]:Up/Down
[SELECT]:Enter
■ Preset listening room types
USER1 (Central wall installation in a small room)
4.2m (13.8ft)
2
Press
/
to select MEMORY, then press
SELECT.
The following screen appears on your TV.
3.4m (11.2ft)
BASIC
OPERATION
SELECT
USER2 (Central wall installation in a mediumsized room)
6.2m (20.3ft)
;MEMORY
4.6m (15.1ft)
LOAD SELECT
)USER1 USER2 USER3
[<]/[>]:Select
[SELECT]:Enter
USER3 (Central wall installation in a large room)
7.6m (24.9ft)
3
Press / to select the room type you want
to set up, then press SELECT.
5.4m (17.7ft)
SELECT
To resume cursor button operations after changing the
control area by pressing an input selector button, press
TEST on the remote control.
TEST
;MEMORY
LOAD SELECT
USER1 Load now ?
To return to the prvious screen while using SET MENU,
press RETURN on the remote control.
[SELECT]:Enter
RETURN
21
STEPS TO ENJOYING SURROUND SOUND
4
Press SELECT once more.
The parameters for the selected room type are loaded.
;MEMORY
LOAD SELECT
SELECT
USER1 Loading !
[<]/[>]:Select
Enjoying TV in surround sound
You can enjoy analog audio signals output by your TV in
real surround sound.
y
Before performing the steps below, set this unit’s volume to
–40 dB. If necessary, adjust the volume level in step 4 below.
1
Select the TV channel you want to watch.
To select a TV channel, use the remote control
provided with your TV.
2
Press TV on this unit’s remote control.
This unit outputs audio signals from your TV.
Once the parameters are loaded, the display returns to
the following screen.
SET MENU
.;MEMORY
;EASY SETUP
;MANUAL SETUP
TV
5
p
p
[]/[]:Up/Down
[SELECT]:Enter
Press SET MENU.
The SET MENU screen disappears from your TV.
3
If you can hear sound from your TV speakers,
reduce the volume level on your TV until you
can no longer hear any audio being output.
To reduce the TV volume level, use the remote
control provided with your TV.
4
To adjust the volume level, press
VOLUME +/– on this unit’s remote control.
SET MENU
VOLUME
22
STEPS TO ENJOYING SURROUND SOUND
5
To select a surround mode, press
SURROUND repeatedly (or press
SURROUND, then press / ) on this unit’s
remote control.
Signals input from 2-channel sources are played back
on multiple channels.
For more information on surround modes, see
page 32.
SURROUND
or
SURROUND
SELECT
BASIC
OPERATION
• To make more detailed listening environment settings,
see page 24.
• To make advanced settings for this unit, see page 36.
23
EASY SETUP
EASY SETUP
If the preset listening environment settings available in “Selecting a preset listening environment” do not match the
characteristics of your listening room, follow the procedure below to set each listening environment parameter
individually using EASY SETUP.
ROOM TYPE > SP POSITION (Speaker position) > ROOM SIZE
y
• For speaker position, sound beam, digital input and display settings, see MANUAL SETUP (page 36).
• Items with a checkmark (*) appearing next to them may be displayed differently on your screen depending on your individual settings
■ ROOM TYPE (Room type)
Using EASY SETUP
2
NIGHT
SURROUND
SET MENU
CH LEVEL
Check that the following screen is displayed
on your TV.
If this screen is not displayed, press SET MENU.
MENU
SET MENU
.;MEMORY
;EASY SETUP
;MANUAL SETUP
SELECT
RETURN
TEST
p
p
[]/[]:Up/Down
[SELECT]:Enter
O
■ Displaying the SET MENU screen on
your TV
You can display the SET MENU screen on your TV for
easier viewing.
1
3
Press
/
to select EASY SETUP, then
press SELECT.
The following screen appears on your TV.
Press SET MENU.
The SET MENU screen appears on your TV.
The operation buttons for SET MENU are displayed
at the bottom of the screen.
SELECT
SET MENU
SET MENU
.;MEMORY
;EASY SETUP
;MANUAL SETUP
p
p
[]/[]:Up/Down
[SELECT]:Enter
;EASY SETUP
y
• To return to the previous screen while using SET MENU, press
RETURN on the remote control.
• To resume cursor button operations after changing the control
area by pressing an input selector button, press TEST on the
remote control.
• To cancel the SET MENU screen, press SET MENU once
more.
• You can also perform the following operation in the front panel
display.
• If you press an input selector button during SET MENU
operation, the cursor buttons become ineffective. In this casee,
press TEST once.
24
.1 ROOM TYPE ?
2
3
4
Push [SELECT] Key.
EASY SETUP
■ SP POSITION (Speaker position)
4
Press SELECT once more.
The display switches between the SQUARE and
RECTANGLE selection screens.
6
1 ROOM TYPE ?
Check that the following screen is displayed
on your TV.
If this screen is not displayed, make the settings in
“ROOM TYPE (Room type)”.
SQUARE
;EASY SETUP
[<]/[>]:Select
[SELECT]:Enter
LE.E* SQUARE
EQ. 2 SP POSITION ?
LE.E3
.E4
Push [SELECT] Key.
SELECT
1 ROOM TYPE ?
RECTANGLE
7
[<]/[>]:Select
[SELECT]:Enter
Press / to select the desired setting, then
press SELECT.
2 SP POSITION
-
CENTER
[<]/[>]:Select
[SELECT]:Enter
SELECT
SELECT
SELECT
2 SP POSITION
-
Select the shape that best suits your listening room.
• Select SQUARE if the shape of your listening
room is nearest to a square.
• Select RECTANGLE if the shape of your listening
room is nearest to a rectangle.
If the shape of your listening room is irregular, select
the shape that most closely resembles your room.
In Example 1, the shape that best describes the
listening room is RECTANGLE. In Example 2, it is
SQUARE.
Example 1:
Rectangular
room
Example 2:
Square
room
WIDE
CENTER
[<]/[>]:Select
[SELECT]:Enter
8
Press / to select the position type that
best suits the installation location of this
unit, then press SELECT.
SELECT
SELECT
Proceed to “ROOM SIZE (Room size)”.
Proceed to “SP POSITION (Speaker position)”.
25
BASIC
OPERATION
5
Press SELECT.
If you selected SQUARE for ROOM TYPE (Room
type) (page 24), the four SQUARE room types are
displayed as shown on page 26
If you selected RECTANGLE, eight different
RECTANGLE room types are displayed
EASY SETUP
SQUARE (Square)
If you selected SQUARE in “ROOM TYPE (Room type)” on page 24:
CORNER
(Corner left or right)
RIGHT (Right)
CENTER (Center)
LEFT (Left)
RECTANGLE (Rectangle)
If you selected RECTANGLE in “ROOM TYPE (Room type)” on page 24:
WIDE LEFT
(Wide wall left)
CORNER LEFT
(Corner left)
NARROW LEFT
(Narrow wall left)
26
WIDE RIGHT
(Wide wall right)
WIDE CENTER
(Wide wall center)
CORNER RIGHT
(Corner right)
NARROW CENTER
(Narrow wall center)
NARROW RIGHT
(Narrow wall right)
EASY SETUP
■ ROOM SIZE (Room size)
11
9
Check that the following screen is displayed
on your TV.
If this screen is not displayed, make the settings in
“SP POSITION (Speaker position)”.
Press / to select the size that best suits
your listening room, then press SELECT.
SELECT
;EASY SETUP
SELECT
LE.E* SQUARE
EQ.>* CENTER
LE.E3 ROOM SIZE ?
LE.E4
Push [SELECT] Key.
Proceed to “SETUP OK (Register settings)”.
10
BASIC
OPERATION
Press SELECT.
If you selected SQUARE in ROOM TYPE (Room
type) (page 24), SMALL, MID and LARGE are
displayed.
If you selected RECTANGLE, SMALL, MID and
LARGE are displayed.
When SQUARE is selected
3 ROOM SIZE ?
MID
. 5.4m .
SELECT
[<]/[>]:Select
[SELECT]:Enter
When RECTANGLE is
selected
3 ROOM SIZE ?
MID
4.6m
. 6.2m
.
.
.
[<]/[>]:Select
[SELECT]:Enter
27
EASY SETUP
SMALL (Small listening room)
Approx. 3.4 m (11.2ft)
3.8 m (12.5ft)
3.8 m (12.5ft)
Approx.
4.2 m (13.8ft)
• Select SMALL if both the width (W) and depth (D) of your listening room are 3.8 m (12.5ft), or the width (W) is
approximately 3.4 m (11.2ft) and the depth (D) approximately 4.2 m (13.8ft).
MID (Medium-sized listening room)
Approx. 4.6 m (15.1ft)
5.4 m (17.7ft)
5.4 m (17.7ft)
Approx.
6.2 m (20.3ft)
• Select MID if both the width (W) and depth (D) of your listening room are 5.4 m (17.7ft), or the width (W) is
approximately 4.6 m (15.1ft) and the depth (D) approximately 6.2 m (20.3ft).
LARGE (Large listening room)
Approx. 5.4 m (17.7ft)
6.6 m (21.7ft)
6.6 m (21.7ft)
Approx.
7.6 m (24.9ft)
• Select LARGE if both the width (W) and depth (D) of your listening room are 6.6 m (21.7ft), or the width (W) is
approximately 5.4 m (17.7ft) and the depth (D) approximately 7.6 m (24.9ft).
28
EASY SETUP
■ SETUP OK (Register settings)
12
• If you select NO, your EASY SETUP settings are
cancelled, and the display returns to the initial SET
MENU screen.
Check that the following screen is displayed
on your TV.
If this screen is not displayed, make the settings in
“ROOM SIZE (Room size)”.
SET MENU
;MEMORY
.;EASY SETUP
;MANUAL SETUP
LE.E*
EQ..*
LE.E*
. 4
SQUARE
CENTER
MID
SETUP OK ?
p
p
[]/[]:Up/Down
[SELECT]:Enter
;EASY SETUP
• To return to the previous screen, press RETURN.
Push [SELECT] Key.
15
13
Press SELECT.
The following screen appears.
Press SET MENU to complete the SET MENU
procedure.
SET MENU
4 SETUP OK?
DATA SETUP
NO
The OSD disappears from your TV screen.
This completes the parameter settings for EASY SETUP.
To select a playback source and enjoy surround sound on
this unit, see “Selecting an input source” on page 31.
14
Press /
SELECT.
to select YES or NO, then press
YES: To register the settings if they are satisfactory.
NO: To cancel the settings and return to the initial
SET MENU screen.
4 SETUP OK?
DATA SETUP
)YES
NO
[<]/[>]:Select
[SELECT]:Enter
• If you select YES, the following screen appears,
and your EASY SETUP settings are registered.
4 SETUP OK?
Data Setting !
Please wait.
29
BASIC
OPERATION
)YES
[<]/[>]:Select
[SELECT]:Enter
VOLUME CONTROLS
VOLUME CONTROLS
Adjusting the volume
Muting the sound
VOLUME
TV VOL
MUTE
TV MUTE
TV INPUT
INPUT
VOLUME
+
TV
DVD
Press MUTE.
“AUDIO MUTE ON” appears in the front panel display,
and the VOLUME indicator blinks.
STANDBY/ON
MUTE
VOLUME
TV VOL
MUTE
Remote control
TV MUTE
VOL
TV INPUT
TV
DVD
To increase the volume output level, press
VOLUME +/–.
Adjustment range: 0.0 dB to –99.5 dB, MUTE (mute)
VOLUME
–
VOLUME
+
or
Front panel
Remote control
VOL
30
To resume the audio output, press MUTE again (or press
VOLUME +/–).
y
You can adjust whether the output volume is muted completely or
by 20 dB when you press MUTE (see page 39).
PLAYBACK
PLAYBACK
Selecting an input source
Playing back sources
You can playback sound and/or images from the various
components connected to this unit simply by pressing one
of the input selector buttons (TV, DVD, VCR or AUX) on
the remote control.
This section uses a DVD player as the playback
component (source).
y
For details on the TV and DVD player you are using, refer to the
owner’s manual supplied with your TV and DVD player.
TV MUTE
TV INPUT
TV
DVD
SLEEP
AUX
VCR
1
Turn on the power to your DVD player using
the supplied remote control.
2
Switch the video input on your TV using the
supplied remote control until the screen for
your DVD player is displayed.
3
If necessary, turn down the volume of your
TV until you cannot hear any sound.
4
Press DVD on the remote control.
The playback source for this unit switches to DVD.
To playback a TV program
Press TV.
TV
DVD
To playback a DVD
Press DVD.
DVD
5
VOL
Playback the DVD on your DVD player using
the supplied remote control.
Audio signals from your DVD player are output from
this unit’s speakers.
y
To playback a video tape
Press VCR.
• If the output volume is too low, increase the volume on this unit
to around –25 dB.
• If you have set remote control codes for your TV and DVD
player, you can use this unit’s remote control to operate these
components. For details on how to set remote control codes, see
page 51.
VCR
VOL
To playback a component connected to the AUX
jack
Press AUX.
AUX
VOL
31
BASIC
OPERATION
VOL
SELECTING A SURROUND MODE
SELECTING A SURROUND MODE
Playback sources and their
available surround modes
Depending on the playback source and selected surround
mode, the indicators in the front panel display light up as
follows.
Enjoying 2-channel sources with
multi channels
You can enjoy a variety of surround sound effects by
switching the surround mode, including multi-channel
decoding for 2-channel sources, and 5.1-channel playback
During CD playback:
SURROUND
NIGHT
SET MENU
PCM
CH LEVEL
MENU
During DTS Digital signal input or when DTS
Neo:6 is selected:
SELECT
RETURN
TEST
VOLUME
During Dolby Digital signal input:
DIGITAL
Press SURROUND repeatedly (or press
SURROUND, then press / ).
SURROUND
When Dolby Pro Logic is selected:
PL
or
When Dolby Pro Logic II is selected:
SURROUND
PL
SELECT
y
You can select the type of input signal by pressing an input
selector button (see page 47).
Surround Modes and Recommended Usages
Recommended
source
Surround mode
Dolby Pro Logic
32
–
All sources
Dolby Pro Logic II
Movie
Music
Game
Movies
Music
Games
DTS Neo:6
Cinema
Music
Movies
Music
ADDITIONAL PLAYBACK MODES
Surround mode parameters
You can configure the parameters for Dolby Pro Logic II
Music and DTS Neo:6 Music to fine-tune the surround
sound effect.
1
Press
2
Press
/
/
to select the parameter.
to configure the parameter.
PANORAMA (when selecting PLII Music)
Gives front L/R channel sound a wraparound effect,
distributed throughout the entire surround sound
field, for an expansive feeling.
Choices: ON/OFF (Default: OFF)
DIMENSION (when selecting PLII Music)
CENTER WIDTH (when selecting PLII Music)
Distributes the center channel sound to the left and
right. If set to 0, center channel sounds output only
from the center speaker.
Variable range: 0 to 7 (Default: 3)
C. IMAGE (when selecting DTS Neo:6 Music)
Adjusts the center image from three speakers (front
and center) to varying degrees.
Variable range: 0.0 (wider) to 0.5 (toward the center)
(Default: 0.2)
Night listening modes
The night listening modes are designed to improve
listenability at lower volumes or at night. Choose either
NIGHT:CINEMA or NIGHT:MUSIC depending on the
type of material you are playing.
Press NIGHT on the remote control repeatedly to
select cinema or music.
When night listening is selected, the NIGHT indicator in
the front panel display lights up.
NIGHT
• Select NIGHT:CINEMA when watching films to
reduce the dynamic range of film soundtracks and
make dialog easier to hear at lower volumes.
• Select NIGHT:MUSIC when listening to music sources
to preserve ease-of-listening for all sounds.
• Select OFF if you do not want to use this function.
Press / to adjust the effect level while
NIGHT:CINEMA or NIGHT:MUSIC is displayed.
This adjusts the level of compression.
Effect.Lvl:MID
• Select MIN for minimum compression.
• Select MID for standard compression.
• Select MAX for maximum compression.
33
BASIC
OPERATION
Adjusts the difference in volume between front and
surround channels to the volume balance you desire.
Variable range: -3 (toward the surround direction) to
+3 (toward the front direction) (Default: STD)
ADDITIONAL PLAYBACK
MODES
ADJUSTING BEAM MODE SETTINGS
ADJUSTING BEAM MODE SETTINGS
You can change the beam mode to suit the input source for this unit using the beam mode buttons. You can switch
between: stereo mode for 2-channel sources, 3 beam mode and 5 beam mode and ST(STEREO)+3 beam mode for
5.1-channel playback.
If you selected a wall installation type (instead of corner) for this unit in EASY SETUP – SP POSITION (page 25), or
you selected wall for MANUAL SETUP – SP POSITION (page 40), all modes are available for selection.
If you selected a corner installation type (instead of wall) for this unit in EASY SETUP – SP POSITION (page 25), or
you selected CORNER for MANUAL SETUP – SP POSITION (page 40), only the stereo and ST(STEREO)+3 beam
modes can be selected.
SLEEP
AUX
VCR
BEAM MODE
Stereo mode
Outputs audio from the front left and right speakers.
This mode is ideal for playing back hi-fidelity
sources, such as CDs, and should be used to replace
your TV speakers. When playing multi-channel
sources, all signals except those for the front left and
right speakers are mixed down and output from the
front left and right speakers. You can select surround
mode during beam mode, but surround mode
becomes disabled when stereo mode is selected.
3 beam mode
Outputs audio from the front left, center and front
right speakers.
Because the listening position area is widened when
signals are output to the front speaker positions only,
you can enjoy excellent quality surround sound over a
wider area. This mode is ideal when you want to
enjoy movies with the whole family.
When playing multi-channel sources, surround left
and right signals are mixed down and output to the
front left and right speaker positions.
Remote control
5 beam mode
Remote control
Outputs audio signals from the front left and right,
center, and surround left and right speakers.
This mode is ideal for enjoying surround sound
effects to the fullest when watching movie DVDs
recorded in a multi-channel format or playing back 2channel sources in a multi-channel format.
To achieve to best surround sound effect, make sure
that there are no objects placed in the path of sound
beams that may prevent the beams from rebounding
directly off your listening room wall. The front left
and right sound beams are output towards the wall.
Remote control
34
ADJUSTING BEAM MODE SETTINGS
ST(STEREO)+3 beam mode
Outputs sound beams to the front left and right,
center, and surround left and right speaker positions.
This mode is ideal when watching live recordings on
DVD.
Vocals and instrumental sounds can be heard close to
the center of the listening position, while sound
reflections from the venue itself can be heard to your
right and left, giving you the feeling that you are
sitting right in front of the stage.
The front left and right sound beams are output
directly at the listening position.
Remote control
BASIC
OPERATION
35
MANUAL SETUP
MANUAL SETUP
To achieve the best quality surround sound, you can use MANUAL SETUP to fine-tune the listening environment
parameters, as well as make advanced settings for speaker positions, sound beams, digital input and the OSD.
Change the initial settings (indicated in bold under each parameter) to reflect the needs of your own listening
environment.
y
Most of the parameters described in SOUND MENU are set automatically when you perform EASY SETUP (see page 24). Use
SOUND MENU to make additional adjustments.
SOUND MENU
Item
Features
Page
SUBWOOFER SET
Customizes the various subwoofer settings.
38
SPEAKER LEVEL
Adjusts the output level of each speaker.
38
DYNAMIC RANGE
Adjusts the dynamic range for Dolby Digital or DTS signals.
39
AUDIO SET
Customizes the muting level and audio delay.
39
TONE CONTROL
Adjusts the output level of high-frequency or low-frequency sound.
39
BEAM MENU
Use to manually adjust listening room parameters or alter the quality and tone of the sound output by this unit.
Item
Features
Page
PARAMETER
Customizes listening room and listening position settings.
40
BEAM ADJ
Adjusts the various beam settings.
41
ROOM EQ
Adjusts the tonal quality of the listening room.
42
BEAM TONE
Adjusts the output level of high-frequency or low-frequency sound for each speaker.
42
IMAGE LOCATION
Adjusts the position of the front left and right speakers.
43
MEMORY
Saves and calls up setting contents.
43
INPUT MENU
Use to reassign digital input/outputs and select the input mode.
Item
Features
Page
INPUT ASSIGNMENT
Assigns jacks according to the component to be used.
44
INPUT MODE
Selects the initial input of the source.
44
INPUT RENAME
Renames the displayed input source.
44
OPTION MENU
Use to adjust the optional system parameters.
Item
Features
Page
DISPLAY SET
Adjusts the brightness of the display and OSD.
45
UNIT SET
Changes the display unit of measurement.
46
y
BEAM MENU allows you to make surround sound effects settings normally available in the speaker settings menu.
36
MANUAL SETUP
Using SET MENU
3
Use the remote control to access and adjust each
parameter.
NIGHT
SURROUND
Press
/
to select a sub menu, then
press SELECT.
SET MENU
CH LEVEL
SELECT
MENU
SELECT
RETURN
TEST
VOLUME
4
y
Use
/
/ /
each parameter.
and SELECT to configure
You can change SET MENU parameters while the unit is
reproducing sound.
1
Press SET MENU.
The SET MENU screen appears on your TV.
The operation buttons for SET MENU are displayed
at the bottom of the screen.
SET MENU
SET MENU
5
To exit, press SET MENU when finished.
.;MEMORY
;EASY SETUP
;MANUAL SETUP
p
p
Press
/
to select MANUAL SETUP,
then press SELECT.
The following screen appears on your TV.
SET MENU
ADVANCED
OPERATION
[]/[]:Up/Down
[SELECT]:Enter
2
SELECT
The OSD disappears
from your TV screen
SELECT
;MANUAL SETUP
p
p
.1 SOUND MENU
2 BEAM MENU
3 INPUT MENU
4 OPTION MENU
[]/[]:Up/Down
[SELECT]:Enter
37
MANUAL SETUP
SOUND MENU
Use the manually adjust any speaker setting or
compensate for video signal processing delays.
(SET MENU → MANUAL SETUP →
SOUND MENU)
1 SOUND MENU 1/2
p
p
.A)SUBWOOFER SET
B)SPEAKER LEVEL
C)DYNAMIC RANGE
D)AUDIO SET
[]/[]:Up/Down
[SELECT]:Enter
■ SUBWOOFER SET (Subwoofer set)
Use to manually adjust subwoofer settings.
A)SUBWOOFERSET
p
p
.BASS OUT;;;;;;BOTH
CROSS OVER;;;100Hz
LFE LEVEL;;;;;;0dB
DISTANCE;;;;;;3.0m
[]/[]:Up/Down
[<]/[>]:Select
DISTANCE (Distance)
Select to adjust the distance of the subwoofer from the
listening position.
Choices: 0.3 to 15.0 m (1 to 50 ft)
Initial setting: 3.0 m (10 ft)
■ SPEAKER LEVEL (Speaker level)
You can manually balance the speaker levels between the
front left or surround left speakers and each speaker
selected.
When setting the front right, center or surround left
speakers or the subwoofer, the test tone is output from the
front left speakers and the selected speaker position.
When setting the surround right speaker, the test tone is
output alternately from the surround left and right
speakers.
When PARAMETER is adjusted in EASY SETUP or
MANUAL SETUP, the factory default value is
automatically set for this parameter.
Depending on beam mode settings, some channels may
not be available for selection.
In this case, “NONE” is displayed.
B)SPEAKER LEVEL 1/2
- +
.FR
C
SL
*OUT : FL )FR
*MODE: 5 BEAM
[]/[]:Up/Down
[<]/[>]:Select
p
38
LFE LEVEL (Low-frequency effect level)
Select to adjust the output level of the LFE (low-frequency
effect) channel according to the capacity of your
subwoofer. The LFE channel carries low-frequency
special effects which are only added to certain scenes.
This setting is effective only when this unit decodes Dolby
Digital or DTS signals.
Choices: –20 to 0 dB
p
BASS OUT (Bass out)
Low-frequency (bass) signals can be directed to the
subwoofer and/or the front left and right speaker positions.
This setting also determines the routing of LFE (lowfrequency effect) signals found in Dolby Digital or DTS
sources.
Choices: SWFR (subwoofer), FRONT, BOTH
Initial setting: BOTH
• Select SWFR if you connect a subwoofer. LFE and
low-frequency signals from other channels are directed
to the subwoofer according to the speaker settings.
• Select FRONT if you do not use a subwoofer. LFE and
low-frequency signals from other channels are directed
to the front speakers according to the speaker settings
(even if you have previously set the front speakers to
SMALL).
• Select BOTH if you connect a subwoofer and you want
to output low-frequency signals from front channels to
both the front speakers and subwoofer. LFE and lowfrequency signals from other channels are also directed
to the subwoofer according to the speaker settings. Use
this function to reinforce low-frequency signals using
the subwoofer when playing back sources such as CDs.
CROSS OVER (Cross over)
When BASS OUT is set to SWFR, you can use this
feature to select a cross-over (cut-off) frequency for all
low-frequency signals. All frequencies below the selected
frequency will be sent to the subwoofer speaker position.
Choices: 80Hz, 100Hz, 120Hz
• FR adjusts the balance of the front left and front right
speakers.
• C adjusts the balance of the front left and center
speakers.
• SL adjusts the balance of the front left and surround
left speakers.
• SR adjusts the balance of the surround left and
surround right speakers.
• SWFR adjusts the balance of the front left speaker and
subwoofer.
MANUAL SETUP
■ DYNAMIC RANGE (Dynamic range)
■ TONE CONTROL (Tone control)
Use to select the amount of dynamic range compression to
be applied to the speakers. This setting is effective only
when the unit is decoding Dolby Digital and DTS signals.
Dynamic range is the difference between the smallest
sound that can be heard above the noise of the equipment
and the biggest sound that can be heard without distortion.
Choices: MIN (minimum), STD (standard),
MAX (maximum)
You can adjust the tonal quality of your speakers.
STD )MAX
[<]/[>]:Select
[SELECT]:Retern
Select to adjust the speaker compression.
• Select MIN for listening to sources at low volume
levels.
• Select STD for general use.
• Select MAX for feature films.
+
p
MIN
p
C)DYNAMIC RANGE
E)TONE CONTROL
.TREBLE
;;;;;0dB
BASS
;;;;;0dB
[]/[]:Up/Down
[<]/[>]:Select
TREBLE (Treble)
Use to adjust the high frequency response.
Choices: –12 dB to +12 dB
Initial setting: 0 dB
BASS (Bass)
Use to adjust the low frequency response.
Choices: –12 dB to +12 dB
Initial setting: 0 dB
■ AUDIO SET (Audio set)
Use to customize this units overall audio settings.
D)AUDIO SET
.MUTE LEVEL;;;MUTE
AUDIODELAY;;;0ms
ADVANCED
OPERATION
p
p
[]/[]:Up/Down
[<]/[>]:Select
MUTE LEVEL (Muting level)
Use to adjust how much the mute function reduces the
output volume.
Choices: MUTE, –20 dB
• Select MUTE to completely halt all output of sound.
• Select –20 dB to reduce the current volume by 20 dB.
AUDIO DELAY (Audio delay)
Use to delay the sound output and synchronize it with the
video image. This may be necessary when using certain
LCD monitors or projectors.
Choices: 0 to 160 ms
39
MANUAL SETUP
BEAM MENU
Use to manually adjust settings for the beams output by
this unit.
When you set the options in PARAMETER, related
settings are automatically adjusted to suit your listening
environment.
(SET MENU → MANUAL SETUP → BEAM MENU)
2 BEAM MENU 1/2
Wall installation
(WALL)
Corner installation
(CORNER)
p
p
.A)PARAMETER
B)BEAM ADJ
C)ROOM EQ
D)BEAM TONE
[]/[]:Up/Down
[SELECT]:Enter
ROOM WIDTH (LEFT WALL)
(Width of listening room left wall)
If SP POSITION is set to WALL, use this to set the width
of your listening room.
If SP POSITION is set to CORNER, use this to set the
length of the wall in front and to the left of the listening
position.
When you set the SP POSITION parameter in EASY
SETUP (page 25) or MANUAL SETUP (page 40), this
item is automatically set to the factory default value.
Choices: 2.0 m to 12.0 m (6.5 ft to 40.0 ft)
■ PARAMETER (Parameter settings)
Use to set the position of this unit in your listening room
and the distance of this unit from the listening position.
A)PARAMETER1/3
p
p
.SP POSITION
;;;;;;WALL
SP HEIGHT
;;;;;;1.0m
[]/[]:Up/Down
[<]/[>]:Select
SP POSITION (Speaker position)
Use to adjust the installation position of your speakers.
Choices: WALL (wall), CORNER (corner)
Wall installation
(WALL)
Corner installation
(CORNER)
ROOM LENGTH (RIGHT WALL)
(Length of listening room right wall)
If SP POSITION is set to WALL, use this to set the
distance from the speaker to the rear wall of your listening
room.
If SP POSITION is set to CORNER, use this to set the
length of the wall in front and to the right of the listening
position.
When SP POSITION is adjusted in EASY SETUP
(page 25) or MANUAL SETUP (page 40), the factory
default value is automatically set for this parameter.
Choices: 2.0 m to 12.0 m (6.5 ft to 40.0 ft)
Wall installation
(WALL)
SP HEIGHT (Speaker height)
Use to adjust the height of this unit from the floor.
Choices: 0 m to 3.0 m (0 ft to 10.0 ft)
Initial setting: 1.0 m (3.5 ft)
YSP-1
0 m to 3.0 m
(0ft to 10.0ft)
Floor
40
Corner installation
(CORNER)
MANUAL SETUP
USER POSITION (User position)
Use to set the distance of the listening position from this
unit.
Choices: 2.0 m to 9.0 m (6.5 ft to 30.0 ft)
2.0 m to 9.0 m
HORIZ. ANGLE (Horizontal angle)
Use to adjust the horizontal angle of beams for each
speaker.
Adjust towards – (minus) to move the direction of the
output to the left, and adjust towards
+ (plus) to move it to the right.
By adjusting the horizontal angle of the beams, you can
optimize the sound beam paths.
A test tone is automatically output.
Choices: –90° to +90°
(+)
(–)
(–)
(+)
(–)
(+)
TO L WALL (Listening position to left wall)
If SP POSITION is set to WALL, use to set the distance of
the center of this unit from the left wall.
Choices: 0.6 m to 11.4 m (2.0 ft to 38.0 ft)
Use to manually adjust the various speaker beam angles.
We recommend that you select 5 beam mode before
adjusting these parameters.
When SP POSITION is adjusted in EASY SETUP
(page 25) or MANUAL SETUP (page 40), the factory
default value is automatically set for this parameter
(except when FOCAL LENGTH is set to CENTER).
Depending on the beam mode settings (page 34), some
speaker positions may not be available for selection. In
this case, “– –” is displayed. When using ST(STEREO)+3
beam mode, set the surround left and right signals to be
output from the front left and right speakers.
(+)
0°
(–)
B)BEAM ADJ
p
p
.a)HORIZ. ANGLE
b)VERTICAL ANGLE
c)DISTANCE
d)FOCAL LENGTH
[]/[]:Up/Down
[SELECT]:Enter
41
ADVANCED
OPERATION
■ BEAM ADJ (Beam adjustment)
VERTICAL ANGLE (Vertical angle)
Use this to adjust the vertical angle of beams for each
speaker.
Adjust towards – (minus) to move the angle downward,
and adjust towards + (plus) to move the angle upward. By
altering the beam path, you can optimize sound beam
angles.
A test tone is automatically output.
Choices: –90° to +90°
Initial setting: 0
MANUAL SETUP
DISTANCE (Distance)
You can use this to set the distance beams travel after
being output and reflected off the wall, until they arrive at
the listening position for each speaker.
The lines in the illustration below indicate the distance.
Choices: 0.3 m to 24.0 m (1.0 ft to 80.0 ft)
• FRONT L/R adjusts the distance the front left and
right speaker sound beams travel.
• CENTER adjusts the distance the center speaker sound
beams travel.
• SURROUND L/R adjusts the distance the surround
left and right speaker sound beams travel.
■ ROOM EQ (Room equalizer)
You can use this to change the tonal qualities of your
listening room when the unit is mounted on the wall.
Choices: STANDARD (standard), LIVE (live), WALL
MOUNT (wall mount)
C)ROOM EQ
ROOM EQUALIZER
;;;;STANDARD
[<]/[>]:Select
[SELECT]:Return
STANDARD (Standard)
Select if your listening room has normal reflectivity.
LIVE (Live)
Select if your listening room has highly reflectivesurfaces,
such as concrete walls.
Front speaker
Center speaker
You can adjust the high and low frequency levels for each speaker.
Choices: –12.0 dB to +12.0 dB
Initial setting: 0 dB
D)BEAM TONE 1/5
*Front L
. TREBLE
+
;;;;;;0dB
BASS
;;;;;;0dB
[]/[]:Up/Down
[<]/[>]:Select
p
Example:
■ BEAM TONE (Beam tone)
p
FOCAL LENGTH (Focal length)
Use this to set the distance from the front of this unit to the
focal point of output for each speaker.
Adjust towards – (minus) to move the focus outward, and
adjust towards + (plus) to move the focus towards the
normal position.
We recommend that you use the initial setting (–0.5 m) for
the center speaker.
Choices: –1.0 m to +13.0 m (–3.5 ft to +43.5 ft)
• FRONT L/R adjusts the focal length for the front left
and right sound beams.
• CENTER adjusts the focal length for the center sound
beams. Initial setting: –0.5 m (–1.5 ft)
• SURROUND L/R adjusts the focal length for the
surround left and right sound beams.
WALL MOUNT (Wall mount)
Select to enhance medium to low range sounds when this
unit is mounted on your listening room wall with a metal
wall bracket, etc. close to the wall.
• Front L TREBLE adjusts the high frequency output
level of the front left speaker.
• Front L BASS adjusts the low frequency output level
of the front left speaker.
• Front R TREBLE adjusts the high frequency output
level of the front right speaker.
• Front R BASS adjusts the low frequency output level
of the front right speaker.
• Center TREBLE adjusts the high frequency output
level of the center speaker.
• Center BASS adjusts the low frequency output level
of the center speaker.
• Surround L TREBLE adjusts the high frequency
output level of the surround left speaker.
• Surround L BASS adjusts the low frequency output
level of the surround left speaker.
• Surround R TREBLE adjusts the high frequency
output level of the surround right speaker.
• Surround R BASS adjusts the low frequency output
level of the surround right speaker.
y If the reflection point of the front left/right or surround left/
right sound beams is a curtain or other acoustically absorbent
surface, you can achieve more effective surround sound by
increasing the treble level for those sound beams.
42
MANUAL SETUP
■ IMAGE LOCATION (Image location)
■ MEMORY (User memory)
You can adjust the direction from which front left and
right speaker sound is heard by directing these audio
signals so that they are also output from the center
speaker.
Use this feature to redirect audio signals if the sound
coming from the left and right speakers seems unnatural,
such as when your listening position is not the center of
your listening room.
You can only adjust this parameter when 3 beam mode or
5 beam mode is selected.
Choices: ON, OFF
Setting range: 0% to 95%
Initial setting: 0%
Saves and loads setting contents for SET MENU.
For example, if there are curtains in the path of beams, the
effectiveness of the beams will vary depending on whether
the curtains are open or closed.
In this case, it is handy to save settings according to the
conditions of your listening room.
Choices: USER1, USER2, USER3
F)MEMORY 1/2
SAVE SELECT
)USER1 USER2 USER3
p
p
[]/[]:to Save
[<]/[>]:Select
[SELECT]:Enter
E)IMAGE LOCATION
.
)OFF
ON
LEFT;;;;;;;;;;0%
RIGHT;;;;;;;;;0%
p
p
[]/[]:Up/Down
[<]/[>]:Select
LEFT (Left)
Adjusts audio signals towards the left.
The higher the percentage, the louder the output from the
center.
Without adjustment
LOAD (Load)
Loads memory settings. Initially, three listening
environments are set as the factory default settings. For
details, see page 57.
When the curtains are
open
When the curtains are
closed
ADVANCED
OPERATION
RIGHT (Right)
Adjusts audio signals towards the right.
The higher the percentage, the louder the output from the
center.
SAVE (Save)
Saves settings in this unit’s memory. (The listening
environments set as the factory default settings will be
erased.)
With the front right
speaker adjusted
43
MANUAL SETUP
■ INPUT MODE (Input mode)
INPUT MENU
Use to reassign digital input from external components
connected to this unit.
(SET MENU → MANUAL SETUP → INPUT MENU)
Use this feature to designate the input mode for sources
connected to the DIGITAL INPUT jacks when you turn on
this unit. For information on the types of audio signals that
can be output by this unit, see “Surround Modes and
Recommended Usages” on page 32.
Choices: AUTO, LAST
3 INPUT MENU
B)INPUT MODE
)AUTO
p
p
.A)INPUT ASSIGNMENT
B)INPUT MODE
C)INPUT RENAME
[]/[]:Up/Down
[SELECT]:Enter
LAST
[<]/[>]:Select
[SELECT]:Retern
■ INPUT ASSIGNMENT (Input assignment)
You can assign the optical and coaxial digital input jacks
of this unit to other components if this unit’s initial
settings do not correspond to your needs. By assigning
other components to the input jacks on this unit, you can
display the name of the connected component in the front
panel display and OSD (see page 20), and operate the
component with the input selector button of the same
name. If you connect a component to this unit’s input
jacks and do not assign it, the default component name for
that input jack is displayed in the front panel and OSD
when selected.
• OPTICAL IN(1) assigns components to the TV
OPTICAL IN jack of this unit.
Choices: TV, VCR
• Select AUTO to allow this unit to automatically detect
the type of input signal and select the appropriate input
mode.
• Select LAST to set this unit to automatically select the
last input mode used for that source. If the type of input
signal is different from the setting, no sounds will be
produced.)
■ INPUT RENAME (Input rename)
Use this feature to change the name of the inputs on the
OSD and front panel display. Press an input selector
button (TV, DVD, VCR, or AUX) to select the component
you want to change the name for, then perform the
following procedure.
C)INPUTRENAME
TV ->
OPTICAL IN (1/2)
TV
p
[<]/[>]:Position
[]/[]:Chara.
p
p
(1);;;;; TV
(1);;;;(
TV
)
(2);;;;; AUX
(1);;;;( AUX
)
[]/[]:Up/Down
[<]/[>]:Select
p
(.
(.
(.
(.
• OPTICAL IN(2) assigns components to the AUX
OPTICAL IN jack of this unit.
Choices: AUX, DVD
• COAXIAL IN(3) assigns components to the
COAXIAL IN jack of this unit.
Choices: DVD, AUX
COAXIAL IN (2/2)
. (3);;;;;
. .
.
(
DVD
DVD
1
Press TEST.
TEST
2
Press / to place the _ (underbar) under
the space or the character you want to edit.
The _ (underbar) blinks.
)
p
p
[]/[]:Up/Down
[<]/[>]:Select
SELECT
44
MANUAL SETUP
3
Press
/
to select the character you
want.
• You can use up to 8 characters for each input.
• Press
to change the character in the following
order, or press
to go in the reverse order:
A to Z, a space, 0 to 9, a space, a to z, a space, #, *,
+, etc.
OPTION MENU
You can use this menu to adjust the optional system
parameter, such as OSD settings and the display unit of
measurement.
(SET MENU → MANUAL SETUP →
OPTION MENU)
4 OPTION MENU
p
p
.A)DISPLAY SET
B)UNIT SET
[]/[]:Up/Down
[SELECT]:Enter
■ DISPLAY SET (Display settings)
4
Repeat steps 1 and 2 to rename each input.
5
To exit, press SELECT when finished.
The new name(s) are registered, and the display
returns to the previous screen.
Use to adjust the brightness of the front panel display.
A)DISPLAYSET 1/2
p
p
.STANDARD DIMMER
;;;;;;;;;;OFF
AUTO DIMMER
;;;;;;;;;;OFF
[]/[]:Up/Down
[<]/[>]:Select
SELECT
AUTO DIMMER (Auto dimmer)
If no operation is performed for a specified period, the
front panel display dims. Use to adjust the brightness of
the front panel display in this case.
Choices: DISPLAY OFF, –3 to –1 (based on the
STANDARD DIMMER setting), OFF
OSD SHIFT (OSD shift)
Use to adjust the vertical position of the OSD. Adjust in
the – (minus) direction to raise the position of the OSD,
and adjust in the + (plus) direction to lower it.
Choices: –5 to +5
Initial setting: 0
OSD BACK COLOR (OSD background color)
Use to select the background color of the OSD.
Choices: BLUE, GRAY
45
ADVANCED
OPERATION
STANDARD DIMMER (Standard dimmer)
Use to adjust the brightness of the front panel display
when this unit is operated via the front panel or remote
control.
Choices: –2, –1, OFF
MANUAL SETUP
■ UNIT SET (Unit settings)
You can use this to change the display unit of
measurement.
Choices: METERS, FEET
B)UNIT SET
)METERS
FEET
[<]/[>]:Select
[SELECT]:Retern
• Select METERS to input speaker distances in meters.
• Select FEET to input speaker distances in feet.
46
SELECTING AN INPUT MODE
SELECTING AN INPUT MODE
You can select the type of input signals you want this unit to use.
• AUTO
Automatically selects input signals in the following order:
1) Digital signals
2) Analog signals
Use this input mode in most cases.
INPUT
VOLUME
+
• DTS
Selects only digital signals encoded in DTS.
Compared to AUTO, this input mode provides greater
stability during playback.
Use this input mode when playing DTS-CD or DTS-LD
discs
STANDBY/ON
• ANALOG
Selects analog signals when both digital and analog
signals are input simultaneously.
TV MUTE
TV INPUT
SLEEP
TV
AUX
y
DVD
You can adjust the default input mode this unit selects when the
power is turned on (see page 44).
VCR
ADVANCED
OPERATION
Press and hold INPUT on the front panel, or
an input selector button on the remote
control.
When you press these buttons, you can confirm the
currently selected input mode. By pressing and
holding them, you can adjust input mode settings.
The setting for VCR is ANALOG.
INPUT
or
TV
DVD
AUX
AUTO
AUTO
AUTO
DTS
DTS
DTS
ANALOG
47
MANUALLY ADJUSTING OUTPUT LEVELS
MANUALLY ADJUSTING OUTPUT LEVELS
You can adjust the output level of each speaker to achieve a more true-to-life surround sound experience. You can adjust
the sound beam output levels for each beam mode.
Using the test tone
3
You can use the test tone feature to output a test tone from
each speaker to manually balance the speaker levels.
Use the test tone to set speaker levels, so that the volume
from each speaker is identical when heard from your
listening position.
NIGHT
SURROUND
CH LEVEL
SET MENU
MENU
Before proceeding to the next step, adjust the volume
level of this unit using VOLUME +/– on the remote
control.
SELECT
RETURN
TEST
VOLUME
1
Press / to adjust speaker volumes.
Adjustment range: –10 dB to +10 dB
4
Press TEST when you have completed your
adjustment.
Press TEST.
“TEST LEFT” appears in the front panel display, and
a test tone is output from the front left speaker.
TEST
TEST
y
2
48
Press
/
to adjust.
to select the speaker you want
To adjust the output level of your subwoofer, set BASS OUT to
BOTH or SWFR (page 38).
MANUALLY ADJUSTING OUTPUT LEVELS
Adjusting output levels during
playback
You can also manually adjust the speaker levels while
playing back a source, such as a DVD.
NIGHT
SURROUND
4
Press CH LEVEL when you have completed
your adjustment.
CH LEVEL
SET MENU
CH LEVEL
MENU
SELECT
RETURN
TEST
O
1
Press CH LEVEL.
CH LEVEL
2
Press
/
to adjust.
3
Press / to adjust speaker volumes.
Adjustment range: –10 dB to +10 dB
to select the speaker you want
ADVANCED
OPERATION
49
USING THE SLEEP TIMER
USING THE SLEEP TIMER
Use this feature to automatically set this unit in the standby mode after a specified time period. The sleep timer is useful
when you are going to sleep while this unit is playing a source.
■ Setting the sleep timer
■ Canceling the sleep timer
You can deactivate the sleep timer setting as follows.
RETURN
TEST
VOLUME
TV VOL
1
MUTE
Press SLEEP repeatedly until “SLEEP OFF”
appears in the front panel display.
SLEEP
TV MUTE
TV INPUT
TV
DVD
SLEEP
AUX
VCR
SLEEP
1
2
Select a source and start playback on the
source component.
Press SLEEP repeatedly to set the amount of
time until this unit goes into standby mode.
Each time you press SLEEP, the front panel display
changes as shown below. The SLEEP indicator blinks
while switching the amount of time for the sleep
timer.
SLEEP
SLEEP
SLEEP 120min
3
SLEEP
90min
SLEEP
60min
SLEEP
30min
SLEEP
OFF
Press RETURN, or wait a few seconds
without operating this unit.
The SLEEP indicator lights up in the front panel
display, indicating that the sleep timer is set.
RETURN
SLEEP
50
2
OFF
Press RETURN, or wait a few seconds
without operating this unit.
The SLEEP indicator goes out, and the sleep timer is
deactivated.
RETURN
SLEEP
Goes out
y
The sleep timer setting can also be deactivated by pressing
STANDBY/ON, or by unplugging the power cable from the AC
outlet.
REMOTE CONTROL FEATURES
REMOTE CONTROL FEATURES
In addition to controlling this unit, the remote control can also operate other A/V components made by YAMAHA and
other manufacturers. To control other components, you must set up the remote control with the appropriate remote
control codes.
Note
Depending on the external AV component you are using, you may not be able to operate the component with this unit’s remote control,
even if a remote control code is set. In this case, operate the component using the supplied remote control.
Setting remote control codes
1
You can control other components by setting the
appropriate remote control codes. Codes can be set up for
each input area (TV, DVD, VCR and AUX).
For a complete list of available remote control codes, refer
to “LIST OF REMOTE CONTROL CODES” at the end of
this manual.
1
2
3
4
5
6
7
8
9
0
+10
While holding down CODE SET, press the
input selector button for the component you
want to set up, then without releasing CODE
SET, enter the remote control code for the
external component using the numeric
buttons.
Refer to “LIST OF REMOTE CONTROL CODES”
at the end of this manual.
Setting example: YAMAHA DVD input area
6
CODE SET
CODE SET
DVD
While holding
down, press
9
CH
9
NIGHT
SURROUND
CH LEVEL
SET MENU
MENU
SELECT
RETURN
TEST
MUTE
TV MUTE
TV INPUT
TV
DVD
SLEEP
AUX
VCR
Refer to “Controlling other components” on
page 52 to operate the external component
using this unit’s remote control.
If the external component functions correctly, remote
control code setup was successful.
If the external component does not function correctly,
the remote control code may be incorrect. Confirm
that the remote control code is correct (see “LIST OF
REMOTE CONTROL CODES” at the end of this
manual) and start over from step 1.
Note
If the manufacturer of your component has more than one code,
try each of them until you find the correct one.
If the remote control is without batteries for more than
2 minutes, or if exhausted batteries remain in the
remote control, the contents of the memory may be
cleared. When the memory is cleared, insert new
batteries and reset the remote control codes.
When changing the batteries, be careful not to press
any of the buttons on the remote control. Doing so will
clear the contents of the memory.
51
ADDITIONAL
INFORMATION
VOLUME
TV VOL
2
REMOTE CONTROL FEATURES
Controlling other components
■ Operating your TV
■ Operating your DVD player
STANDBY/ON
AV
2
STANDBY/ON
POWER
1
2
3
5
6
7
POWER
1
AV
4
2
8
1
2
3
5
6
7
3
0
4
8
CODE SET
CODE SET
9
1
9
+10
0
+10
CH
CH
3
NIGHT
SURROUND
NIGHT
SET MENU
CH LEVEL
CH LEVEL
MENU
5
SELECT
RETURN
TEST
SET MENU
MENU
4
SELECT
RETURN
TEST
VOLUME
TV VOL
SURROUND
6
VOLUME
TV VOL
MUTE
MUTE
TV MUTE
TV MUTE
4
6
TV INPUT
TV
DVD
SLEEP
AUX
VCR
5
TV INPUT
TV
DVD
SLEEP
AUX
VCR
TV
DVD
Press TV to switch the input to TV.
Press DVD to switch the input to DVD.
1 POWER
Turns on/off the TV’s power.
1 POWER
Turns on/off the DVD player’s power.
2 Numeric buttons
Selects a TV channel for playback.
2 Numeric buttons
Use to enter numeric digits.
3 CH +/–
Switches between the TV channels available.
3 Operation buttons for DVD and VCR players
Use to perform DVD player operations, such as play and
stop.
4 TV VOL +/–
Adjusts the audio output level of the TV.
5 TV MUTE
Temporarily mutes audio output from the TV.
6 TV INPUT
Switches the input source for the TV.
52
4 MENU
Displays the DVD menu.
5 Cursor buttons
Use to select DVD menu items.
6 RETURN
Use to return to the previous DVD menu screen or exit the
DVD menu.
REMOTE CONTROL FEATURES
■ Operating your VCR player
STANDBY/ON
POWER
AV
2
■ Returning to theYSP-1 operation mode
1
2
3
5
6
7
1
4
8
CODE SET
9
3
0
+10
CH
4
NIGHT
SURROUND
CH LEVEL
To return to the YSP-1 operation mode, press one of
the following keys.
For details on each key, see page 8 or 20.
NIGHT
SURROUND
SET MENU
CH LEVEL
TEST
SET MENU
MENU
SELECT
RETURN
TEST
VOLUME
TV VOL
MUTE
TV MUTE
TV INPUT
TV
DVD
SLEEP
AUX
VCR
VCR
Press VCR to switch the input to VCR.
1 POWER
Turns on/off the VCR player’s power.
ADDITIONAL
INFORMATION
2 Numeric buttons
Use to enter numeric digits.
3 CH +/–
Switches between the VCR channels available.
4 Operation buttons for DVD and VCR players
Use to perform VCR player operations, such as play and
stop.
53
TROUBLESHOOTING
TROUBLESHOOTING
Refer to the chart below when this unit does not function properly. If the problem you are experiencing is not listed below
or if the instruction below does not help, set this unit to the standby mode, disconnect the power cord, and contact the
nearest authorized YAMAHA dealer or service center.
■ General
Problem
Cause
Remedy
Refer to
page
This unit fails to turn
on when STANDBY/
ON is pressed, or
enters the standby
mode soon after the
power has been
turned on.
The power cable is not connected or the
plug is not completely inserted.
Connect the power cable firmly.
17
This unit has been exposed to a strong
external electric shock (such as lightning
and strong static electricity).
Set this unit in the standby mode, disconnect the
power cable, plug it back in after 30 seconds, then use
it normally.
—
This unit suddenly
enters the standby
mode.
The internal temperature becomes too
high and the overheat protection circuitry
has been activated.
Wait about 1 hour for this unit to cool down and then
turn it back on.
—
The sleep timer has turned the unit off.
Turn on the power, and play the source again.
—
Incorrect input or output cable
connections.
Connect the cables properly. If the problem persists,
the cables may be defective.
11
No appropriate input source has been
selected.
Select an appropriate input source with INPUT or the
input selector buttons.
31
The volume is turned down.
Turn up the volume.
30
The sound is muted.
Press MUTE or VOLUME +/– on the remote control
to resume audio output, then adjust the volume.
30
Signals this unit cannot reproduce are
being received from a source component,
such as a CD-ROM.
Play a source whose signals can be reproduced by this
unit.
—
The sleep timer has turned the unit off.
Turn on the power, and play the source again.
—
The sound is muted.
Press MUTE or VOLUME +/– on the remote control
to resume audio output, then adjust the volume.
30
No sound from the
effect speakers.
You are playing back the source or
program in stereo mode.
Press one of the beam mode buttons on the remote
control to select a multi-channel playback mode, then
try to playback the source or program once more.
34
No sound from the
center speaker.
The output level of the center speaker is
set to minimum.
Raise the level of the center speaker.
48
No sound from the
surround speakers.
The output level of the surround speakers
is set to minimum.
Raise the output level of the surround speakers.
48
No sound from the
subwoofer.
BASS OUT in SUBWOOFER SET is set
to FRONT when a Dolby Digital or DTS
signal is being played.
Select SWFR or BOTH.
38
No sound
The sound suddenly
goes off.
The source does not contain low bass
signals.
54
TROUBLESHOOTING
Problem
Cause
Remedy
Refer to
page
Surround sound
effects are
insubstantial.
The listening room is not a regular shape.
Install this unit in a square or rectangular shaped
room.
—
There is no wall in the path of the beam.
Place a flat object, such as a board, in the path of the
beam.
—
Dolby Digital or DTS
sources cannot be
played. (Dolby Digital
or DTS indicator in
the front panel
display does not light
up.)
The connected component is not set to
output Dolby Digital or DTS digital
signals.
Make an appropriate setting following the operating
instructions for your component.
—
The input mode is set to ANALOG.
Set the input mode to AUTO.
47
Low frequency
sounds are distorted.
CROSS OVER in SUBWOOFER SET is
set incorrectly.
Set CROSS OVER correctly.
38
On-screen display
does not appear.
The OSD video cable is not connected
properly.
Connect the cable properly.
12
TV is not selected as the input source.
Select TV as the input source.
31
No picture is
displayed for external
components, such as
a DVD player.
The video cable is not connected properly.
Connect the cable properly.
11
TV is not selected as the input source.
Select TV as the input source.
31
This unit does not
operate properly.
The internal microcomputer has been
frozen by an external electric shock (such
as lightning or excessive static electricity)
or by a power supply with low voltage.
Disconnect the AC power cable from the outlet and
then plug it in again after about 30 seconds.
—
There is noise
interference from
digital or highfrequency equipment.
This unit is too close to the digital or highfrequency equipment.
Move this unit further away from such equipment.
—
This unit does not
output effect sounds
properly.
The original source includes surround
effects.
Disable surround effect settings on this unit.
—
ADDITIONAL
INFORMATION
55
TROUBLESHOOTING
■ Remote control
Problem
The remote control
does not work and/or
function properly.
You cannot operate
external components
with this unit’s remote
control.
The cursor buttons do
not work during SET
MENU operation.
56
Cause
Remedy
Refer to
page
Wrong distance or angle.
The remote control will function within a maximum
range of 6 m (20 ft) and no more than 30 degrees offaxis from the front panel.
19
Direct sunlight or lighting (from an
inverter type of fluorescent lamp, etc.) is
striking the remote control sensor of this
unit.
Reposition this unit.
—
The batteries are weak.
Replace all batteries.
18
The external component you want to
operate is not selected as the input source.
Press INPUT or the input selector buttons to select
the external component you want to operate.
31
The remote control code was not correctly
set.
Set the remote control code correctly or try another
code for the same manufacturer using the “LIST OF
REMOTE CONTROL CODES” at the end of this
manual.
51
Even if the remote control code is
correctly set, there are some models that
do not respond to the remote control.
Use the remote control supplied with the external
component.
—
You pressed an input selector button.
Press TEST once.
24
RESETTING THE FACTORY PRESETS
RESETTING THE FACTORY PRESETS
If you want to reset all of your unit’s parameters for any
reason, do the following. This procedure completely resets
ALL the parameters in SET MENU.
3
Note
After performing the following procedure you must reset the
ROOM TYPE, SP POSITION and ROOM SIZE parameters to
match your surround sound environment.
Press INPUT once more.
“RESET” appears in the front panel display.
To cancel without making any changes, press INPUT
again to display “Cancel”.
Reset
INPUT
Be sure this unit is in standby mode.
Cancel
4
Press STANDBY/ON to confirm your
selection.
If you selected “Reset”, the unit is reset to its factory
presets and switches to standby mode.
If you selected “Cancel”, the unit switches to standby
mode and nothing is reset.
STANDBY/ON
INPUT
1
VOLUME
+
STANDBY/ON
Hold down INPUT on the front panel and
press STANDBY/ON.
“FACTORY PRESET” appears in the front panel
display.
INPUT
While holding
down, press
STANDBY/ON
ADDITIONAL
INFORMATION
VOL
y
To cancel the initialization procedure without making any
changes, press STANDBY/ON.
2
Release INPUT.
INPUT
57
FRONT PANEL DISPLAY ITEMS
FRONT PANEL DISPLAY ITEMS
■ POWER STANDBY/ON
VOLUME -40.0dB
■ EASY SETUP
ROOM TYPE
1 ROOM TYPE?
SP POSITION
2 SP POSITION?
ROOM SIZE
3 ROOM SIZE?
SETUP OK
4 SETUP OK?
■ MANUAL SETUP
SOUND MENU
1 SOUND MENU
BEAM MENU
2 BEAM MENU
INPUT MENU
3 INPUT MENU
OPTION MENU
4 OPTION MENU
■ SWITCHING BETWEEN EXTERNAL
COMPONENTS
When TV is selected as the source
TV AUTO
When DVD is selected as the source
DVD AUTO
When VCR is selected as the source
VCR
When AUX is selected as the source
AUX AUTO
■ SURROUND MODE
When PLO LOGIC is selected
PRO LOGIC
When PLII Movie is selected
PLII Movie
When PLII Music is selected
PLII Music
When PLII Game is selected
PLII Game
When Neo:6 Cinema is selected
Neo:6 Cinema
When Neo:6 Music is selected
Neo:6 Music
■ NIGHT LISTENING MODE
When CINEMA is selected
NIGHT:CINEMA
When MUSIC is selected
NIGHT:MUSIC
When OFF is selected
NIGHT OFF
■ BEAM MODES
When stereo mode is selected
STEREO MODE
When 3 beam mode is selected
3 BEAM MODE
When 5 beam mode is selected
5 BEAM MODE
When ST(STEREO)+3 beam mode is selected
ST+3 BEAM MODE
■ SOUND
When adjusting the volume
VOLUME -40.0dB
When the sound is muted
AUDIO MUTE ON
When the mute function is released
AUDIO MUTE OFF
While a test tone is being output
TEST LEFT
58
GLOSSARY
GLOSSARY
Audio formats
■ Dolby Digital
Dolby Digital is a digital surround sound system that gives
you completely independent multi-channel audio. With 3
front channels (left, center, and right), and 2 surround
stereo channels, Dolby Digital provides 5 full-range audio
channels. With an additional channel especially for bass
effects, called LFE (low frequency effect), the system has
a total of 5.1-channels (LFE is counted as 0.1 channel). By
using 2-channel stereo for the surround speakers, more
accurate moving sound effects and surround sound
environment are possible than with Dolby Surround. The
wide dynamic range (from maximum to minimum
volume) reproduced by the 5 full-range channels and the
precise sound orientation generated using digital sound
processing provide listeners with previously unheard of
excitement and realism.
With this unit, any sound environment from monaural up
to a 5.1-channel configuration can be freely selected for
your enjoyment.
■ Dolby Pro Logic II
Dolby Pro Logic II is an improved technique used to
decode vast numbers of existing Dolby Surround software.
This new technology enables a discrete 5-channel
playback with 2 front left and right channels, 1 center
channel, and 2 surround left and right channels (instead of
only 1 surround channel for conventional Pro Logic
technology). Music and Game modes are also available for
2-channel sources in addition to the Movie mode.
■ Dolby Surround
DTS digital surround was developed to replace the analog
soundtracks of movies with a 6-channel digital sound
track, and is now rapidly gaining popularity in movie
theaters around the world. Digital Theater Systems Inc.
has developed a home theater system so that you can enjoy
the depth of sound and natural spatial representation of
DTS digital surround in your home. This system produces
practically distortion-free 6-channel sound (technically, a
left, right and center channels, 2 surround channels, plus
an LFE 0.1 channel as a subwoofer, for a total of 5.1channels). The unit incorporates a DTS-ES decoder that
enables 6.1- channel reproduction by adding the surround
back channel to existing 5.1-channel format.
■ Neo:6
Neo:6 decodes the conventional 2-channel sources for 6
channel playback by the specific decoder. It enables
playback with the full-range channels with higher
separation just like digital discrete signal playback. Two
modes are available; “Music mode” for playing music
sources and “Cinema mode” for movies.
■ PCM (Linear PCM)
Linear PCM is a signal format under which an analog
audio signal is digitized, recorded and transmitted without
using any compression. This is used as a method of
recording CDs and DVD audio. The PCM system uses a
technique for sampling the size of the analog signal per
very small unit of time. Standing for “pulse code
modulation”, the analog signal is encoded as pulses and
then modulated for recording.
Audio information
■ LFE 0.1 channel
This channel is for the reproduction of low bass signals.
The frequency range for this channel is 20 Hz to 120 Hz.
This channel is counted as 0.1 because it only enforces a
low frequency range compared to the full-range
reproduced by the other 5/6 channels in Dolby Digital or
DTS 5.1/6.1-channel systems.
59
ADDITIONAL
INFORMATION
Dolby Surround uses a 4 channel analog recording system
to reproduce realistic and dynamic sound effects: 2 front
left and right channels (stereo), a center channel for dialog
(monaural), and a surround channel for special sound
effects (monaural). The surround channel reproduces
sound within a narrow frequency range.
Dolby Surround is widely used with nearly all video tapes
and laser discs, and in many TV and cable broadcasts as
well. The Dolby Pro Logic decoder built into this unit
employs a digital signal processing system that
automatically stabilizes the volume on each channel to
enhance moving sound effects and directionality.
■ DTS (Digital Theater Systems)
Digital Surround
INDEX
INDEX
A
Audio Pin Cable ............................................................. 12
B
Beam modes ................................................................... 34
C
Coaxial digital output jack ............................................. 13
Coaxial digital input jack ............................................... 13
D
Digital Audio Pin Cable ................................................. 13
Display........................................................................ 6, 20
Dolby Digital .................................................................. 32
Dolby Pro Logic ............................................................. 32
Dolby Pro Logic II.......................................................... 32
DTS ................................................................................ 32
Dynamic range................................................................ 39
E
EASY SETUP ................................................................ 24
L
LFE 0.1 channel.............................................................. 59
M
MANUAL SETUP ......................................................... 36
MEMORY ................................................................ 21, 43
N
Night listening modes..................................................... 33
60
O
On-screen display (OSD)................................................ 20
OSD video cable ............................................................. 12
Optical cable ............................................................. 12, 15
P
PCM ................................................................................ 32
Power cable..................................................................... 17
R
Remote control............................................................ 8, 18
Remote control code ....................................................... 51
S
Surround mode................................................................ 32
Sleep timer ...................................................................... 50
SET MENU .............................................................. 24, 37
T
Test tone.......................................................................... 48
SPECIFICATIONS
SPECIFICATIONS
AMP SECTION
• Maximum Output Power (EIAJ)
................................................2 W (1 kHz, 10% THD, 10 Ω) × 40
20 W (100 Hz, 10% THD, 4 Ω) × 2
SPEAKER SECTION
Small dia. speakers
............................... 4 cm (1.5”)-cone magnetic shielding type× 40
Woofers................. 11 cm (4.5”)-cone magnetic shielding type × 2
• Input Jacks
AUDIO VCR, TV (Analog) (1 V, 32 kΩ)............. 2 pairs (Analog)
AUDIO AUX, TV (Optical) .......................................... 2 (Digital)
AUDIO DVD (Coaxial) ..................................................1 (Digital)
• Output Jacks
SW PRE OUT (1 V, less than 120 Hz) .................... 1 (Subwoofer)
VIDEO OUT OSD (1 Vp-p, 75 Ω).................................... 1 (OSD)
• System Connector Jacks
SYSTEM CONNECTOR ..................................1 (System control)
RS-232C .............................................................1 (System setting)
GENERAL
• Power Supply
[U.S.A. and Canada models] .............................. AC 120 V, 60 Hz
[Australia model] ............................................... AC 240 V, 50 Hz
[U.K. and Europe models] ................................. AC 230 V, 50 Hz
[China model] ..................................................... AC 220 V, 50 Hz
[Korea model] .................................................... AC 220 V, 60 Hz
[General model] ........................................ AC 110–120 V, 50 Hz
[Asia model] ............................................... AC 220–240 V, 50 Hz
• Power Consumption .................................................................. 50 W
• Standby Power Consumption ...................................... 0.5 W or less
• Dimensions (W x H x D) ............................... 1030 × 194 × 118 mm
(40–9/16” × 7–11/16” × 4–5/8”)
• Weight .............................................................. 13 kg (28 lbs 10 oz)
*
Specifications are subject to change without notice.
ADDITIONAL
INFORMATION
61
LIST OF REMOTE CONTROL CODES
TV
ADMIRAL
292, 293, 216
AIWA
294, 276, 283, 284
AKAI
295, 296
ALBA
296
AOC
297
BELL &
HOWELL
292
BESTAR
298
BLAUPUNKT 229, 222
BLUE SKY
298
BRANDT
223
BROC SONIC 297
BUSH
296
CLATRONIC 298
CRAIG
224
CROSLEX
225
CURTIS MATHIS
297, 226
DAEWOO
297, 298, 224,
227, 228
DAYTRON
239
DUAL
298
DWIN
293, 281
EMERSON
297, 224, 239, 232
FURGUSON 223, 265, 266
FIRST LINE 298
FISHER
295, 233
FRABA
298
FUJITSU
289
FUNAI
277, 278
GE
293, 297, 234,
235, 236
GOODMANS 296, 298, 223
GRUNDIG
229, 238, 249
HITACHI
297, 239, 242,
243, 285
ICE
296
IRRADIO
296
ITT/NOKIA
244, 245
JC PENNY
293, 297, 234, 237
JVC
296, 246, 247, 286
KENDO
298
KTV
297, 239
LG/GOLDSTAR
297, 298, 239, 237
LOEWE
298, 248
LXI
293, 297, 225,
226, 233
MAGNAVOX 297, 225, 239
MARANTZ
298, 210
MATSUI
295
MEMOREX
297, 216
MITSUBISHI 299, 297, 259, 287
NAD
226, 255
NEC
297, 252, 282
NOKIA
244, 245
NOKIA OCEANIC
245
NORDMENDE 265, 266
ONWA
296
PANASONIC 234, 235, 236,
253, 288, 211
PHILCO
297, 225, 239
PHILIPS
225
PIONEER
226, 235, 254,
255, 268
PORTLAND 297, 256
PROSCAN
293, 221
PROSCAN
231, 241, 251
i
PROTON
297, 250, 260, 270
QUASAR
234, 235
RADIO SHACK299, 293, 297
RCA
293, 297, 234,
256, 257, 258, 221
RUNCO
220, 230, 271
SABA
223, 269, 265, 266
SAMPO
281, 297, 280
SAMSUNG
297, 239, 248,
262, 275
SANYO
295, 233, 279,
272, 273, 274, 212
SCHNEIDER 296
SCOTT
297
SHARP
292, 239, 232, 213
SIEMENS
229
SIGNATURE 216
SIGNATURE 292
SONY
263, 214
SYLVANIA
297, 225
SYNPHONIC 217, 218, 219
TELEFUNKUN 269, 264, 265, 266
THOMSON
223, 266
TOSHIBA
292, 226, 267, 215
VIDECH
297, 242
WARDS
297, 239, 232, 216
YAMAHA
299, 292, 242,
285, 287, 253
ZENITH
216, 261, 271
DVD PLAYER
AIWA
648, 649
APEX DIGITAL
652, 653, 654
DAEWOO
655
DENON
623, 624
FUNAI
625
HARMAN/KARDON
656, 657
HITACHI
626
JVC
627
KENWOOD
628
KLH
658
LG/GOLDSTAR
645, 663, 664
MARANTZ
699, 659
MITSUBISHI 629
ONKYO
632, 633, 634
PANASONIC 623, 635, 668, 672
PHILIPS
699, 647, 659
PIONEER
636, 637, 638,
673, 674, 675
RCA
639
SAMSUNG
642
SHARP
643
SONY
644, 676, 677
SYLVANIA
662
SYMPHONIC 662
THOMSON
646
TOSHIBA
634, 665, 666, 667
YAMAHA
699, 622, 623, 647
ZERITH
663, 664
VCR
ADMIRAL
395
AIWA
396, 397, 398, 329
AKAI
322, 323, 324
AUDIO DYNAMIC
392, 394
BELL & HOWELL
393
BLAUPUNKT 325, 326
BROC SONIC 327
BUSH
322
CANON
325, 328
CGM
396, 332
CITIZEN
396
CRAIG
396, 363
CURTHIS MATHIS
397, 328, 333
DAEWOO
328, 334, 335
DBX
392, 394
DIMENSIA
333
DYNATECH 397
EMERSON
327, 334, 396, 397
FISHER
393, 336
FUNAI
397
GE
328, 333, 387
GO VIDEO
321, 331, 341,
351, 353, 363
GOODMANS 334, 337
GRUNDIG
332, 338
HITACHI
325, 333, 349,
342, 343
INSTANT REPLAY
325, 328
ITT/NOKIA
393
JC PENNY
392, 393, 394,
328, 333, 349,
396, 363
JVC
392, 394, 344,
345, 346, 347
KENDO
396
KENWOOD
392, 394, 396
LG/GOLDSTAR
396, 388
LOEWE
396, 337
LUXOR
395
LXI
393, 396, 397,
336, 349
MAGNAVOX 325, 326, 328
MARANTZ
392, 394
MARTA
396
MATSUI
396
MEMOREX
328, 336, 396, 397
MINOLTA
333, 349
MITSUBISHI 399, 344, 348,
359, 352, 353
MTC
363, 397
MULTITECH 397, 348, 354
NEC
392, 394, 344, 383
NOKIA
393, 395
NOKIA OCEANIC
395
OKANO
323
OLYMPIC
325, 328
ORION
327
PANASONIC 325, 328, 339,
355, 378, 384,
385, 386
PENTAX
333, 349
PHILCO
325, 328, 397
PHILLIPS
325, 326, 328,
337, 356, 357
PHONOLA
337
PILOT
396
PIONEER
325
QUASAR
325, 328
RCA/PROSCAN
325, 326, 328,
333, 335, 349,
358, 369, 363, 397
REALISTIC
393, 397, 328,
336, 359, 362,
396, 363
SAMSUNG
354, 358, 363,
364, 365, 366
SANSUI
394
SANYO
393, 336, 367
SCHNEIDER 337
SCOTT
399, 335, 336,
348, 359, 352,
354, 358
SELECO
322
SHARP
395, 362, 382
SIEMENS
393
SIGNATURE 2000
395, 397
SONY
368, 379, 372,
373, 374, 375
SYLVANIA
397, 325, 326, 328
SYMPHONIC 397
TANDBERG 334
TANDY
397
TASHIRO
396
TATUNG
392, 394
TEAC
392, 394, 397
TECHNICS
325, 328
TEKNIKA
396
TELEFUNKUN
376, 377
THOMAS
397
THORN
393, 396
TOSHIBA
335, 369, 389
TOTEVISION 363, 396
UNITECH
363
UNIVERSUM 396, 327, 376
VIDEOSONIC 363
W.WHOUSE 396
WARDS
395, 396, 336,
362, 397, 363
YAMAHA
399, 392, 393, 394
ZERITH
344, 361, 368,
371, 379, 396, 397
CABLE
ABC
739, 752, 753,
755, 758, 759, 762
GENERAL INSTRUMENT
722
HAMIN
723, 724, 725,
726, 727
HITACHI
722
JEROLD
722, 728, 729,
732, 733, 734,
735, 736, 737
MAGNAVOX 738
MOTOROLA 748
OAK
739, 742, 743
PANASONIC 744, 745, 746, 747
PHILLIPS
763, 764, 765,
766, 767, 768
PIONEER
748
RADIO SHACK749
SCIENTIFIC ATLANTA
752, 753, 754
SONY
756, 757
TOCOM
755
UNIVERSAL 769, 772, 773,
774, 775
VIEWSTAR
764, 766, 776,
777, 778, 779, 782
SATELLITE TUNER
ECHOSTAR
822
GE
837, 838, 839
GENERAL INSTRUMENT
823
HITACHI
824
HUGHES
843, 844, 845, 846
JVC
822
MAGNAVOX 825
PANASONIC 826, 829
PHILLIPS
825, 843, 844,
845, 846, 847,
848, 849
PRIMESTAR 827
PROSCAN
837, 838, 839, 842
RADIO SHACK
828
RCA
837, 838, 839, 842
SONY
832, 835
TOSHIBA
833, 836
UNIDEN
825
ZENITH
834
ii
© 2004
YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.
YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA
YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, GERMANY
YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE
YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD18 7GQ, ENGLAND
YAMAHA SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN
YAMAHA MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA
All rights reserved.
Printed in Malaysia
WE22570