Fanvil i20T User Manual

I20-T Door Phone

User Manual

VoIPon www.voipon.co.uk [email protected] Tel: +44 (0)1245 808195 Fax: +44 (0)1245 808299

Safety Notices

1. Please use the specified power adapter. If special circumstances need to use the power adapter provided by other manufacturers,please make sure the voltage and current provided in accordance with the requirements of this product, meanwhile, please use the safety certificated products， otherwise may cause fire or get an electric shock.When using this product, please do not damage the power cord，or forcefully twist it、Stretch pull or banding, and not to be under heavy pressure or between items, Otherwise may cause the power cord damage, thus lead to fire or get an electric shock.

2. Before use, please confirm the temperature and environment humidity suitable for the product work.(Move the product from air conditioning room to natural temperature, which may cause this product surface or internal components produce condense water vapor, please open power use it after waiting for this product is natural drying.)

3.Non-technical staff not remove or repair, improper repair or may cause electric shock, fire or malfunction, etc，Which can lead to injury accident, and also can cause your product damage.

4. Do not use fingers, pins, wire and other metal objects, foreign body into the vents and gaps. It may cause current through the metal or foreign body，which even cause cause electric shock and injury accident. If any foreign body or objection fall into the product please stop usage. trap his head with it，may cause nose and mouth blocked，and even lead to suffocation.

6. Please use this product with normal usage and operating，in bad posture for a long time to use this product may affect your health.

7. Please read the above safety notices before installing or using this phone. They are crucial for the safe and reliable operation of the device.

2


Table of Content

1. Acquaint I20-T.................................................... 4

1.1. I20-T Front ............................................................................................................................................................... 4

1.2. Key Description ....................................................................................................................................................... 5

2. Start Using ....................................................... 5

2.1. Connect the power supply and the network .................................................................................................. 5

2.1.1. Connect Network ....................................................................................................................................... 5

2.2. Quick Setting .......................................................................................................................................................... 9

3. I20-T Door Phone Basic Operation ................................ 10

3.1. Answering a Call ................................................................................................................................................. 10

3.3. End a Call .............................................................................................................................................................. 10

3.5. Door Open Operation ......................................................................................................................................... 11

4. Page Configuration .............................................. 11

4.1. Ways to configure ............................................................................................................................................... 11

4.1.1.Ways to configure ..................................................................................................................................... 11

4.1.2. Password Configuration ........................................................................................................................ 11

4.2. Setting via web browser .................................................................................................................................... 11

4.3. WEB Page Functional Explanation ................................................................................................................ 12

4.3.1. BASIC .......................................................................................................................................................... 12

4.3.1.1. Status .............................................................................................................................................. 12

4.3.1.2. Wizard .............................................................................................................................................. 12

4.3.1.3. Call Log ........................................................................................................................................... 15

4.3.2. Network ...................................................................................................................................................... 16

4.3.2.1. WAN Config ................................................................................................................................... 16

4.3.2.2. Qos Config ..................................................................................................................................... 18

4.3.2.3. Service Port ................................................................................................................................... 20

4.3.2.4. TIME&DATE ................................................................................................................................... 21

4.3.3. VOIP ............................................................................................................................................................ 22

4.3.3.1. SIP Config ....................................................................................................................................... 22

4.3.3.2. Stun Config .................................................................................................................................... 28

4.3.5.

FUNCTION KEY ................................................................................................................................... 29

4.3.5.1.

Function key ............................................................................................................................... 29

4.3.5.2.

Door Card Setting ...................................................................................................................... 32

4.3.5.3.

Call Log ........................................................................................................................................ 33

5. Appendix ....................................................... 33

5.1.1.Specifications: ........................................................................................................................................... 34

5.1.2. Basic Feature ............................................................................................................................................ 34

5.1.3. Schematic Diagram ................................................................................................................................... 35

5.2、Owner Remote Opens the Voice Access Controller by VOIP Phone ................................................... 35

5.3、Card Management ............................................................................................................................................. 35

5.3.1 Issue Card Management ........................................................................................................................... 35

5.3.2Issue User Card ........................................................................................................................................... 36

5.3.3 Delete the user card (Method 1): .............................................................................................................. 37

5.3.4、Add Remote Visit Data .......................................................................................................................... 38

3


1. Acquaint I20-T

Voice Intercom I20-T voice entrance guard is a full digital network door phone，its core part adopt Fanvil mature Voip solution（Broadcom1190 chipset), stable and reliable performance, Hands-free adopting digital full-duplex mode，Voice loud and clear；generous appearance, solid durable, easy for installation, comfortable keypad, low power consumption.

I20-T voice entrance guard support entrance guard control、Voice Intercom、keypad remote to open the door.

1.1. I20-T Front

4


1.2.

Key Description

Key Chinese

Specification

Function enter the password to open the door

Or make a calling digit keyboard

Programmable keyboard call status indicators

Can be set to a variety of functions，to meet the needs of different occasions s tandby-light off ring-2 sec.glitter hold/be hold-1sec. Glitter communication by telephone

-long bright power led

（left） Long bright after power supply

Network and SIP status indicator light

（right） network failure

1 sec. glitter network normal light off registration failure 3 sec. glitter registration succeed long bright

2. Start Using

Before you start to use I20-T，please make the following installation：

2.1. Connect the power supply and the network

2.1.1. Connect Network

In prior to this step, please check if your network can work normally and have capacity of broadband internet access.

1. Broadband Router

Connect network one end with I20-T WAN port，connect the other end with your broadband router LAN port,then network hardware connection is completed. In most cases，you must set your

I20-T network as DHCP mode.Please refer to the detailed setting ways 3.2.1, set network.

2. wireless broadband router

5


Connect network one end with I20-T WAN port，connect the other end with your

ADSL modem

LAN port,then network hardware connection is completed. In most cases，If you are using the TV must set your I20-T network as PPPoE mode.Please refer to the detailed setting ways 3.2.1, set

network.

2.1.2.

、Interface Description

2.1.2.

1

Network, Power Switch, Electric Lock Connection

CN7

CN6

CN6

Output 12V

DC

Electric Lock

Driver

1 2 3 4 5 6

COM POE+

12V DC input Normally open, normally

WAN（UTP Cable Connection）

7 8 9 10 11

POE- TX+ TX- RX- RX+ close port

CN7

LAN（UTP Cable Connection）

6


2.1.2.2

Electric Lock Connection Driver Option

JP1

Outside

Driver

1

2

3

4

External Power Driving

JP1

Inside

Driver

1

2

3

4

Internal Power Driving

【Notice】 When the initial electric current of the lock is less than 500mA/12V, you can access to the internal driven mode and use the POE of the Voice Access System or 12V

DC to control the the switch of the electric lock ; When the initial electric current of the lock is more than 500mA/12V, you need to access to the external driven mode(Use specialized

DC power to control the electric lock )

2.1.2.3

Wiring

Relay connection description：

 NO：means idle-disconnected contact (normally open)

 COM: means a pin contact(middle)；

 NC：means an idle-connected contact(normally close)；

Jumper

JP1 mode

Internal External NO NC

Inside

Driver

1

2

3

√ √

4

Mode of connection

7


√ √

Outside

Driver

1

2

3

4

√ √

Inside

Driver

3

4

1

2 mode

Internal Externa l

√

NO NC

√

Jumper

JP1

Outsid e

Driver 3

4

1

2 mode of connection

8


√ √

Outside

Driver

1

2

3

4

2.2. Quick Setting

I20-T Provide a complete function and parameter setting,users may need to have the network and

SIP protocol knowledge for understanding the meaning represented by all parameters.In order to let I20-T users can quickly enjoy the high quality speech brought by the IP Phone services and low cost advantage, we especially lists the basic and must set options in this section，which let users can real-time started without understanding complex SIP protocols.

In prior to this step，p lease make sure your broadband Internet online can be normal operation

，and complete the connection of the network hardware. I20-T factory default network mode is DHCP. Thus,only connect I20-T with DHCP network environment then network can be automatically connected.

1. Long press # keypad 5 Sec，then waiting for the phone play the IP address；or use iDoorPhoneNe twork.exe software to search the IP address

2. Use IP address log onto WEB server to configurate.

3. Configurate service provider supplied account on SIP page，user name，service address and other Registration required parameters. shortcut key on EGS->Function key page.The advice is set to KEY EVENT type， value is OK keyboard.

5.Configurate Door Phone parameter on EGS->EGS page frame.

9


3. I20-T Door Phone Basic Operation

3.1. Answering a Call

When calling come，I20-T will ring，and configurate the shortcut as OK, then can press shortcut and answer the call.

3.2. Making a Call

Configurate shortcut as Memory key and setup a number, then press shortcut can call the configured number immediately.

Configurate shortcut as Dial key. Input wanted number on the keyboard then press short to call.

3.3. End a Call

Configurate shortcut as Release key to end the call.

3.4. Call Records

I20-T provides 100 missed calls、received calls、dialed Calls records，When the storage space used up，then will update the earnest records. Then the phone power of or reboot，all the call records will disappear.

Can check all these three type call records on WEB-Basic->call log page

10


3.5. Door Open Operation

Through the following four ways to open the door:

1. Input the local password on the keyboard to open the door.

2. The door phone call the owner，the owner enter the remote password to open the door.

3. Owner/other phone call the door，then enter the access code and remote password to open the door.

4. Use RFID to open the door.

The access code input errors by low frequency short chirp prompt to door phone and remote user. input error will be prompted by low-frequency sirens sound.

Password input error is prompted by high frequency chirp，input successfully will be prompted by high-frequency sirens sound.

When the door opens by playing intermittent beeps for prompt. Timeout after closing door the prompt will be stoped.

4. Page Configuration

4.1. Ways to configure

4.1.1.Ways to configure

I20-T has two different ways to different users.

：





Use web browser (recommendatory way).

Use telnet with CLI command.

4.1.2.

Password Configuration

There are two levels to access to phone: root level and general level. User with root level can browse and set all configuration parameters, while user with general level can set all configuration parameters except SIP (1-2) or IAX2’s that some parameters cannot be changed, such as server address and port. User will has different access level with different username and password.

 User Name：guest



Password

：guest

 User Name：admin



Password

：admin

4.2. Setting via web browser

When I20-T and PC are connected to network， obtain via pressing sysinfo key）http://xxx

//xxx.xxx.xxx.xxx：xxxx/，otherwise it will show can not find a server

11


）You can see the web management interface login screen（as below image）。Enter the user name and password and click on the【Logon】button then can enter into the set menu.

※:If you do not save the settings you changed，next power boot it will back to the previous state unchanged. If you want to save the settings，after you made the change，please click Maintenance-Config-save then all are saved，in the process, the phone will immediate effect without reboot.

4.3. WEB Page Functional Explanation

4.3.1. BASIC

4.3.1.1. Status

4.3.1.2. Wizard

Field Name

Network

Accounts

Status

Description

Shows the phone current WAN configuration: include WAN IP get way

（S tatic 、DHCP、PPPoE）and MAC address，IP，t he default gateway IP address

Shows the phone current SIP LINE 1－2 r egistered and the corresponding number status. The bottom of the page shows I20-T version number and release date.

12


Wizard

Field Name

Description

Telephone network on-line mode, please according to the actual network environment ， select the appropriate network model.This phone provides three kinds of network online ways：

Static : If your ISP Services provide you with a fixed IP address，you can choose this.After selecting， you must fill the Static table with：IP Address /

Netmask /Gateway / Primary DNS and other related information. If you don't know the information，please ask your ISP service provider or network management personnel for assistance.

DHCP ：in this mode，network information will got automatically from the

DHCP server，you need not to manually enter these fields.

PPPoE：select this mode. you must enter the ADSL online account and password.

You can also reference

3.2.1 Network Settings

， and set your network quickly.

Select Static IP MODE，click【NEXT】can simply configurate the network address and

SIP parameters（default as 1 Line）and browse configuration items. Click

【BACK】r eturn to the last page.

13


IP Address

Subnet Mask

IP Gateway

DNS Domain

Primary DNS

Secondary DNS

Please enter your assigned IP addresses.

Please enter your assigned subnet mask.

Please enter your assigned a default gateway address.

Set the DNS domain suffix. When the user input in the

DNS domain name address and cannot be resolved， telephone will add this domain behind the domain name address then go to resolve.

Please enter your primary DNS server address.

Please enter your alternate DNS server address.

Display Name

Server Address

Server Port

Authentication User

Configure display name ，a ble to do when calling in the called party （ don’t name the caller ） c an show this configuration parameters ， and a llow input English letters ；

Configure the SIP registration server address,Support domain address

Configure the SIP registration server signaling port

Configure the SIP registration account.

Configure the SIP registration account password.

Authentication

Password

SIP User Configure the number registered on IP server.

Enable Registration Configurate to allow/p rohibit the registration ；

14


Show your manual configuration details.

Select DHCP MODE，click【NEXT】c an simple SIP parameter （defaulted as 1 line）

【BACK】 return to the last page specific operation same as Static IP MODE。

Select PPPoE MODE，click【NEXT】can simply configurate online account and password and SIP parameter（defaulted as 1 line）a nd browse configuration items.

Click【BACK】 return to the last page ， specific operation same as Static IP

MODE.

Server name

User service name，e.g. PPPoE service provider has no special requirements ，t he name as the default value is ok.

Please enter your ADSL account.

Password Please enter your ADSL password.

Note：After the above operation is completed please click 【Finish】button， The phone will automatically save the current configuration and reboot ，

After the successfully reboot can use the registered account to make calls.

4.3.1.3. Call Log

Through this page can check all call out record.

Call Log

15


Field Name

Start Time

Duration

Dialed Calls

Type

4.3.2. Network

4.3.2.1. WAN Config

Description

The call log start time.

The call records of talk time.

This call log is the account of other side and call protocol and using line.

Placed(answered),Missed（missed）,Received

（incoming).

Field Name

WAN Config

Description

Active IP Address

Current Subnet Mask

Current IP Gateway

MAC Address

MAC Timestamp

The phone current IP；

Subnet Mask；

The current default gateway IP；

MAC address；

Show the time of getting MAC address

16


Telephone network on-line mode. Please according to the actual network environment ，choose a suitable network mode. This phone provides three ways for network online ：

 static ：If your ISP services provide you with fixed IP address，then you can choose this item. After choosing, you must fill it into Static table：IP

Address / Netmask /Gateway / Primary DNS and other related information.If you don’t know these information，can ask assistance from your ISP provider or network management personnel.

in this mode，network information will automatically obtain from

DHCP server，you need not to manually enter these fields.

 PPPoE： when select this mode，you must enter the ADSL online account and password.

You can reference 3.2.1 Network Settings， set your network quickly.

Only the phone used in Static mode which need set.

IP Address

Subnet Mask

Please enter your assigned IP addresses.

Please enter your assigned subnet mask 。

IP Gateway

DNS Domain

Please enter your assigned a default gateway address.

Set the DNS domain suffix. When the user input in the

DNS domain name address and could not resolute ， after put this domain behind the domain name address then the phone will go to resolve.

Primary DNS

Secondary DNS

Please enter your DNS service address.

Please enter your spare DNS service address.

Only when the phone use PPPoE mode need to set.

Server Name service name, e.g. PPPoE Service provider has no special requirements, this name can be treated as default value.

User Please enter your ADSL account.

Password Please enter your ADSL code.

Note:

1） After setting the parameters, need click “apply”to make it effective.

2）f changed IP ，w eb page must have no longer responding ， at this time should enter the new address in the address bar can be connected to the

17


phone.

3）If system boot and use DHCP to get IP，and DHCP server network address are the same with system LAN network address ，then after server get DHCP IP, add 1 to the last of LAN network address，meanwhile modify LAN DHCP Server allocate

IP address field；After system reboot，WAN access DHCP log on，and DHCP server provided network address is the same as LAN provided，then WAN will not be able to get IP access networks.

4.3.2.2. Qos Config

I20-T Terminal system support802.1Q/P protocol，support DiffServ configuration. Meanwhile，VLAN function can configurate Voice VLA and Data VLAN use different VLAN I.System configuration Data

VLAN，can process the signalling、Audio stream and system and other data stream with different

VLAN ID，which let the applications of VLAN is more flexible.（Below chart is helpful for your understanding the VLAN using advantages.）

In chart

1，on a two layer switch which not set VLAN，any radio frame is forwarded to all the other ports in addition to receiving port. e.g，PC A（port 1）After sending the broadcast information，will be

18


forwarded to the port 2、3、4.

In chart 2，the switch generate red and blue VLAN；Meanwhile set port 1、2 as red VLAN、port 3、

4 are VLAN. Then A（port 1）send out broadcast frame，switches only will forward it to other port belongs to a VLAN——port 2 which also belong to red VLAN，Will not be forwarded to the blue port

VLAN. As well，C（port 3）send out broadcast frame，Will only be forwarded to other belong to the blue port VLAN，Will not be forwarded to belong to the red VLAN ports.

In this way，VLAN by limiting the broadcast frame forwarding range to partition the broadcast domain. In the above chart for better illustration，use red, blue two colors to identify different VLAN， in the practice is using “VLAN ID" to distinguish.

Field Name

LLDP Setup

Open LLDP

Open Learning

Function

Description

Open the phone LLDP Message function

Open phone learning LLDP function ， After the opening ， phone will automatically learn QoS in switch ，VLAN ID，802.1p,etc.configuration value.If differen t

，phone will Automatically updated to the value in switch, synchronization with switches.

Data sending interval

QOS Setup

Open DiffServ

The interval of phone sending data ， the unit is second.Default it is 60 seconds.

Configurate whether open DiffServ

Signal Dscp

Voice Dscp

Configurate the value of Signal Dscp

Configurate the value of Voice Dscp

WAN VLAN Setup

Open WAN Port

VLAN

Open the VLAN of WAN port

19


WAN Port VLAN ID

Signal 802.1P Priority

Voice 802.1P Priority

LAN VLAN Setup

LAN Port Vlan

Configurate ID value of VLAN，range is 0-4095

Configurate the value of Signal 802.1P，range is 0-7

Configurate the value of Voice 802.1P，the range is

0-7

Open/ forbid Port Vlan

Same as WAN port ID value

Close:

Disable

Port Vlan

LAN Port VLAN ID

Open：after open it then input different ID value from

WAN port

Setup ID value of VLAN，range is 0-4095

4.3.2.3. Service Port

Through this page can set Telnet ,HTTP,RTP port.

Field Name

HTTP Port

Telnet Port

RTP Port Range Port

RTP Port Quantity

SERVICE PORT

Description

Configurate web browser port，default 80 port, if want to enhance system security，can modify it to non-80 standard port ，save the data after modification，when lo in again please use this way: http://xxx.xxx.xxx.xxx：xxxx.

Configurate telnet port，default 23port；

Configurate phone RTP and open the starting port.Allocate this port as dynamic allocation；

Configure the phone allocation RTP port Max quantity . Default 200 pieces；

Notice： into force.

20


2）If change Telnet ,HTTP port number ，it’s better set bigger port number than 1024， because 1024 port is system reserved port.

3）HTTP port number is set as 0， then forbid the HTTP service.

4.3.2.4. TIME&DATE

According to their own position、configuration time zone and SNTP Server to automatically obtain time and daylight saving time function，can also according to their need to manually adjust the time.

Field Name

SNTP Time set

SNTP

DHCP Time

Main Server

Backup Server

Territory

SNTP

Description

Configurate whether enable SNTP server

Whether use DHCP dynamic to obtain time，after enabling，phone will synchronization network time automatically in certain time

Configurate phone obtain current time SNTP main server address.

Configurate phone obtain current time SNTP backup

Server address.

Configure the choice for time zone

21


Synchronous Query inquiry from the server constantly to synchronize

12 hours system

Date Format

，default 60 second

System can switch to 12 hours，default is 24 hours

Configure date format

Date Separator Configure date separator summer time set

Open the Daylight

Configure the daylight saving time

Saving Time

Time Change

Length(Minute )

Month

Week

Configure the daylight saving time changing length

Configure DST the starting month and end month

Configure DST the starting week and end week

Configure DST the starting date and end date Date

Hour

Minute

Manually set the

Configure DST the starting hour and end hour

Configure DST the starting minute and end minute time

Manually set the time，need firstly disable SNTP service，in the above chart year、month、date、minute、hour、second every part need filled into and submit then manual set will succeed.

4.3.3. VOIP

4.3.3.1. SIP Config

Configure the SIP server here.

Field Name

SIP Config

Description

22


Choose which line configuration of the SIP account，There are two lines to choose from. Select and click【Load】 switch to the line account configuration

Basic setup registration status

Phone SIP registration status display；if the register will show the registered successfully，Otherwise is unregistered server name

Server Address server port

Name the server

Configure SIP r egister server address

,support domain form address

Configure SIP register server signaling port user name Configure SIP registration account

Password

Telephone number

Display Name

Proxy server address

Configure SIP registration account password

Configure the number registered to the SIP server， if it is empty，then it is not a registered

Configure display names，able to do when calling in the called party（not name the calling party

）can show this configuration parameter，allow input

English letters

Configure proxy server IP address（ generally

，SIP service provide users the use proxy server and register the same server configuration to provide services，thus，the proxy server configuration is usually is the same as the registered server configuration,if the service providers give different registered server from the proxy server IP address configuration ， need modify their server configuration） proxy server port

Configure SIP proxy server signaling port proxy server account Configure proxy server account proxy server password

Set the proxy server password local domain name backup proxy server address

Configure the SIP local domain name. If the server does not require a local domain name to specify the domain name for a SIP terminal，the local domain can be configured with the same address or domain name server.System to simplify the user input，users can not enter the local domain name，the system will automatically get registered address fill in the content of domain realm.

Configure the backup proxy server address，if the master agent server address is unavailable，phone will enable backup proxy server address automatically backup proxy server port

Configure the backup proxy server port

23


Open registration

Codecs

Disable

Codecs/Enable

Codecs

Configure allow/prohibit registration

According to the need by navigation on Disable

Codecs/Enable Codecs list add or remove coding

， and can be used by the priority of the up and down navigation keys to change the coding.

Advance SIP configuration

Forward Type

Choose call forwarding way. call forwarding（default it’s close）

 close：close call forwarding function

 busy：incoming calls when the phone is busy directly forwarded to the specified number



No answer

：incoming calls within a specified time has not been answered，then forwarded to the specified number

 all the time：incoming call will be transferred to the specified number before directly before the forwarding operation，machine indicates

Forward Number

Call Forward No

Answer Delay Time the caller id

C onfigure forward number

If it’s call forward no answer，if nobody answer incoming call in Call Forward No Answer Delay Time then the calling will be forwarded to specified number

For the phone supports the transfer of certain

Transfer timeout special features server, set interval time between sending

“bye” and hanging up after the phone transfers a call.

Enable the hot line

Configure to enable the hotline number number

Hot line number Specify Hot Line Number, the phone dial the hot line number automatically at hands-free mode or handset mode after warm line time.

Hot line delay time

Open signal encryption

Configure hot line delay time

Configure whether to support signaling encryption

Signal encryption key Input signal encryption key encryption

Voice encryption key input speech encryption key

Open the automatic reply

Configure automatic reply

24


Automatic response time

Open dialogue timer

When there is a call in，and over time went unanswered，phone will answer it automatically

Configure whether to support rfc4028,refresh the

SIP sessions

Configure dialogue timeout Dialogue timeout

Subscribe information after a successful

Open MWI registration,can subscribe others’ status or voice subscription mails, and so on.

Configure MWI number，realize sip voice message inform and listen to voice message. When there is a

Voicemail Number new voice message，voicemail will flashing lights， pick up and press MWI key will automatic call to voicemail，and listen to the voice mail，If no new message, voicemail light is out

Subscribe the packet retransmission timeout

Configure subscription time interval

Meeting Type

Specify the Conference Type, if you select the local, you needn’t input the conference number. meeting room number

Registration Expire

Configure meeting room number，please contact your service provider to the meeting room number

Set expire time of SIP server register, default is 60 seconds. If the register time of the server requested is longer or shorter than the expired time set, the phone will change automatically the time into the time recommended by the server, and register again.

Enable Service Code Configure whether enable service code

Set the DND On Code, When you press the DND

DND On Code hot key, the phone will send a message to the server, and the server will turn on the DND function. Then any calls to the extension will be rejected by the server automatically. And the incoming call record

DND Off Code

Always CFwd On

Code

Always CFwd Off will not be displayed in the Call History.

Set the DND Off Code, When you press the DND hot key, the phone will send a message to the server, and the server will turn off the DND function

Set the Always CFwd On Code, when you choose to enable the always forward function on your phone, it will send message to the server, and the server will turn on the function immediately. When there are calls to the extension, the server will always forward it to the set number automatically. And the IP phone will not show the record in the call history anymore.

Set the Always CFwd Off Code, when you choose to

25


Code

Busy CFwd On Code

Busy CFwd Off Code

No Answer CFwd On

Code

No Answer CFwd Off

Code

Anonymous On Code

Anonymous Off Code

Server Detection

Type

Server detection time interval disable the always forward function on your phone, it will send message to the server, and the server will turn off the function immediately.

Set the Busy CFwd On Code, when you choose to enable the busy forward function v on your phone, it will send message to the server, and the server will turn on the function immediately. When there are calls to the extension, the server will forward it to the set number automatically based the forward type. And the IP phone will not show the record in the call history anymore.

Set the Busy CFwd Off Code, when you choose to disable the busy forward function on your phone, it will send message to the server, and the server will turn off the function immediately.

Set the No Answer CFwd On Code, when you choose to enable the on answer forward function on your phone, it will send message to the server, and the server will turn on the function immediately.

When there are calls to the extension, the server will forward it to the set number automatically based the forward type. And the IP phone will not show the record in the call history anymore.

Set the No Answer CFwd Off Code, when you choose to disable the busy forward function on your phone, it will send message to the server, and the server will turn off the function immediately.

Set the Anonymous On Code, When you choose to enable the anonymous call function on your IP phone, it will send information to the server, and the server will enable the anonymous call function for your IP phone automatically.

Set the Anonymous Off Code, When you choose to disable the anonymous call function on your IP phone, it will send information to the server, and the server will disable the anonymous call function for your IP phone automatically.

Configure server detection type，if it’s option，phone will send option SIP message to server every configured time ，server respond 200OK to maintain server detection. If it’s UDP,phone will send option

UDP message to server every configured time

Configure Server detection time interval，if phone enable SIP server detection function，phone will to test whether a server response every configured time

26


User Agent

DTMF Type

Local Port

Ring Type

Enable Via rport

Enable PRACK

User Agent Terminal

Set DTMF sending mode，there are three：

 DTMF_RELAY

 DTMF_RFC2833

 DTMF_SIP_INFO

Different VoIP Service providers may provide different modes.

Set sip port of each line.

Set ring type of each line.

Enable/Disable system to support RFC3581. Via rport is special way to realize SIP NAT.

Enable or disable SIP PRACK function, suggest use the default config.

Enable Long Contact

Set more parameters in contact field; connection with SEM server.

Convert URI

Dial Without

Convert # to %23 when send the URI.

Set call out by proxy without registration;

Registered

Ban Anonymous Call Set to ban Anonymous Call;

Enable DNS SRV Support RFC2782；

Select the special type of server which is encrypted,

Server Type

RFC Protocol Edition or has some unique requirements or call flows.

Select SIP protocol version to adapt for the SIP server which uses the same version as you select.

For example, if the server is CISCO5300, you need

Transport Protocol to change to RFC2543; else phone may not cancel call normally. System uses RFC3261 as default.

Set transport protocols, TCP or UDP

Anonymous call

Specification version

Keep Authentication

Enable Click-to-Call

Set Anonymous call out safely; Support

RFC3323and RFC3325;

Enable/Disable Keep Authentication System will take the last authentication field which is passed the authentication by server to the request packet. It will decrease the server’s repeat authorization work, if it is enable.

Configure

Click-to-Call

；（Need the actual software application support）

Only respond to a speech codec

Auto TCP transfer

Configure

Compatible with special server

Enable GRUU

When it is called,only respond to one supported

Codec

Set to use automatically TCP protocol to guarantee usability of transport as message is above 1300 byte

Compatible with special server（Support the special

SIP server-when phone receives the packets sent from server,phone will use the source IP address, not the address in via field.）

Set to support GRUU

27


Enable Display name

Quote

Enable user=phone

Enable Missed Call

Log

Set to make quotation mark to display name as the phone sends out signal, in order to be compatible with server.

Enable user=phone by selecting it, it is contained in the invite sip message, in order to be compatible with server.

Enable the missed call log by it, the phone will save the missed call log into the call history record and display the missed calls on the idle screen, or won’t save the missed call log into the call history record and display the missed calls on the idle screen.

Enable BLF List

Configure BLF List，BLF List can monitor the state of multiple accounts.

Configure BLF List number BLF List number

SIP Global Settings

Enable the Strict Branch, the value of the branch

Strict matching

Branch field must be in the beginning of z9hG4k in via field of the invite sip message received, or the phone won’t response to the invite sip message.

Notice: the deployment will become effective in all sip lines.

Enable Group function

Enable Group by selecting it, then the phone enable the sip group backup function.


Specify the registration failure retry time, if the phone register failed, the phone will register again

Registration Failure

Retry Time after registration failure retry time.


4.3.3.2. Stun Config

In this web page, you can config SIP STUN.

STUN: By STUN server, the phone in private network could know the type of

NAT and the NAT mapping IP and port of SIP. The phone might register itself to SIP server with global IP and port to realize the device both calling and being called in private

28


network.

4.3.5. FUNCTION KEY

4.3.5.1. Function key

1-4 programmable key in phone software(depend on hardware),you can configurate different feature on each key. You can ref to below indications for each feature, default is NA, means without any feature settings.

。

1) Type=Hot key

Number 1/2 is the fixed phone number, when press the DSS key, the phone call the fixed phone number. this phone number can also be set as IP address.

2) Type=Key Event

You can set type as key event, there’re many options in the subtype for your selection.

 None

 Dial

 Release

 OK

3) Number Setting

Number1 and number2 is 2 different calling number, when the Dial Mode is <Main-Secondary>,

29


Number1 is the Main number and Number2is the secondary number; When the Dial Mode is<Day/Night>,Number1 is the daytime period and Number2 is the night time period

EGS

EGS,to config the door phone and maintenance the visitor data

Setting Item

Open Time

Holding Time

Remote Openig

Time

Local PIN

Tone settings

Keypad mod

（i20T Valid）

Description

Remote phonebook settings

Voice Access Configuration

Function

Time for open the door, if time is up, the door will be closed automatically.

After time is up, the call will be ended automatically.

Remote opening password.

Local password for the keypad

Mute/Short beeps/Long beeps

Password only(Prohibit call)/Password-Dial

Displayed on iDoorPhoneNetworkScanner software

Enabling access phone: when remote phone calls, input access code first then input password to open the door.

Disabling access phonebook: when remote

5s

120s

*

Initial Value

6789

Bell ringing

Dialing and password input i20 IP door phone

Enable

30


phone calls, input password only.

Eanble

Touchpad

Enable Card

Reader

Provide keyboard function

Provide card reader function open open

Dial Mode Select

Time of Switch

Day Start Time

Day End Time

<Primary /Secondary>mode corresponds to the first number in one-button Call function, <Day/Night>mode corresponds to the second number in one-button Call function

The period between one-button Call function to call the first and second number

When select <Day/Night>mode, the time to start Day time

When select <Day/Night>mode, the time to end up Day time

Primary /secondary

16s

06:00

18:00

Address of Log

Server

Port of Log

Server

Enable Log

Server

Enable Indoor

Open

Log server address（IP）

Log server port（0-65535，default:514）

Enable or Disable the log server

Disable

Use to disable or enable the indoor open function

Disable

Remote Phonebook

Number

Authentication

code

Remote phone number

Access code for visitor. When remote phone calls, if the number is in access list, you can input access code to open the door.

When IP phone calls, it needs to input

authentication code to control voice access controller.

Type of Host

Name

Position

Department

When owner calls, controller answer automatically, when visitor calls, controller mute.

Card holder’s name

Card holder’s position

Card holder’s department

Card number RFID’s number

To add new visitor, add the visitor number in <Number> and <Access Code>;Visitor’s Name,

Position and Department is optional; And then Select the ID (Card number) and Access Type

(Visitor or Owner).Press<Add> key to add new visitor. The visitor can call the door phone and input the access code to open the door or use ID card to open the door. Maximum 100 visitors

To modify visitor data, click <Delete> or <Modify> key to delete/modify the visitor data, all data can be modified except calling number

31


After you set the log server, i20T will send log data to the log server.

Data format:

<8>MAR 20 11:17:38 5,0003476426,IC Card,I20 IP Door Phone

[Note]:

 “<8>”:log level

 “MAR 20 11:17:38”: happen time

 “5,0003476426,IC Card,I20 IP Door Phone”:logs have include door open time ,Card number/phone number ,open door type ,device .

4.3.5.2. Door Card Setting

Door Card Setting,to config the ID card and admin the card issue and delete

State

Code

Administrator Table

Add Administrator

Door Card Setting

Explanation

ID Card Status Setting:

Normal Status, Wave card to open the door

Card Issuing Status, Update the ID card data to phone database

Card Revoking Status, Delete the ID card data from the database

Administrator data table, display the administrator ID, Date and Type

Add Administrator, Admin Card Number, Type,

Card Issuer and Revocation. When the ID Card status is in <Normal>,wave admin card to enter

32


Delete Administrator

Door Card Table

4.3.5.3. Call Log card issuing mode, and then wave the additional cards into the database, when the procedure completed, wave admin card again to enter

Normal status.(Delete card procedure is same),Maximum 10 Admin Card and 100 visitor card

To delete Admin Card, select the card number and click<delete>

ID card database, display the card number and

Issuing Date

Display call history,Maximum 2000 call history,the earlist excessed call history will be deleted automatically.Right-Click to export Call Log in CSV format

Code

Start Time

Duration

Peer Calls

Type

Call Log

Explanation

Time for door openning

Door Opening Duration time

Caller ID(Remote Opening),Card ID number(IC card),N/A(local)

Door opening type: Local, Remote, IC card

5. Appendix

33


5.1.1.Specifications:

Key

Voice

Voice Flow

PORT

Protocol

Chipset

Key Material

Direct-button

Digital Keyboard

Microphone

Amplifier

Speaker

Voice Control

FDSP

Protocol

CODEC

Power Supply

PoE

LAN

Recommended Cable

Passive Switch

SIP 2.0(RFC-3261)

Broadcom 1190

Stainless Steel

1

support

1

0.5W/8 Ω

0.5W/8 Ω

Adjustable

Support(AEC)

RTP

G.711, G.729

12V+-15%/1A DC or PoE

PoE 802.3af (Class 0 - 12.95W)

48V/380mA

10/100BASE-TX s Auto-MDIX,

RJ-45（Keep press key in 7 seconds to play IP）

HSYV or better

Always on and Always close highest at 30V/1A AC/DC

12V/500mA DC

Support

Support

RFID/IC Card

Reader(Optional)

Active Switched Output

RS232

EM-40XX (125Khz)

HID Card(125kHz,

26bit)

M1 Card（13.56MHz）

Not support

Not support

Shell Material

Operating Temperature

Aluminum Cover、Plastic back case

-20°C to 70°C

Working Condition

Relative Humidity

Storage Temperature

Installation

10% - 95%

-40°C to 70°C

Embedded installation (pre-burying)

Structure

Overall Dimension：174.5╳96╳44m

Size pre-burying Mounting Dimension：

148╳80╳36mm

Protection

Level(Water proof/Damp proof)

5.1.2. Basic Feature

 Support G.711,G.729 codec.

 Support SIP 2.0(RFC3261) and related RFC.



Unlock function (swipe or communication)

 Water Proof and Dust Proof;

IP54

34




Visitor message

；



Calling indoor extension for two-way conversation；



Software upgrading on line；





WEB remote management of Terminal malfunction or status；

5.1.3. Schematic Diagram

Call/Answer Indicator

Red: Power Indicator

Green: Network/Registration

Indicator

Rain Cover

Mic

Digital Keyboard (Password input or Number dial)

Intercom call button

Speaker

Fixing Screw

5.2、Owner Remote Opens the Voice Access Controller by VOIP Phone

1）Owner calls the Voice Access Controller by VOIP Terminal.

2）the Voice Access Controller answers the call automatically.

3）Owner enter Authentication code by VOIP Terminal’s keypad to open the door.

5.3、Card Management

5.3.1

Issue Card Management

35


（1） Issue <issue administration card>

Input available card number to ID input field, choose Issuer, then press Add to add Issue

Administration Card.

（2）Issue <Delete administration card>

Input available card number to ID input field, choose “Revocation”, then press Add to add Delete

Administration Card.

（3）Administration Card List

5.3.2

Issue User Card

Issue User Card (method 1):

1） Choose “Card Issuing” in “Door Card”.

2） Press “Apply” to submit new User Card.

36


3) Put IC card on the Reader Sensing Area, and make sure the reader responded.

4） Choose “Normal” in the Card Reader Setting.

5）Press “Apply”.

6）You can check the issuing records in “Door Card Table”

Issue the User Card (Method 2):

1） Put Issue Administration Card on the Reader Sensing Area, the controller is on the state of issuing.

2） Put IC card on the Reader Sensing Area, and make sure the reader responded.

3） Put Issue Administration Card on the Reader Sensing Area again to sign out issuing, then the reader is back to the normal state

5.3.3

Delete the user card (Method 1):

1) Choose “Card Issuing” in “Door Card”.

37


2) Press “Apply” to enter the state of deleting card,

3) Put IC card on the Reader Sensing Area, and make sure the reader responded.

4) Choose “Normal” in the “Card Reader Setting”.

5）Press “Apply” .

Delete the user card (Method 2):

1） Put Issue Administration Card on the Reader Sensing Area, the controller is on the state of deleting.

2） Put IC card on the Reader Sensing Area, and make sure the reader responded.

3） Put Issue Administration Card on the Reader Sensing Area again to sign out deleting, then the reader is back to the normal state.

5.3.4、Add Remote Visit Data

（1）Add new number

After finish filling accounts, choose the number for the user, press “Add”.

38


（2）Remote Visit Table

39


Fanvil i20T User Manual

I20-T Door Phone

User Manual

Safety Notices

Table of Content

1. Acquaint I20-T

1.1. I20-T Front

1.2.

2. Start Using

2.1. Connect the power supply and the network

、Interface Description

1

Wiring

√ √

√ √

√ √

√

√

√ √

2.2. Quick Setting

3. I20-T Door Phone Basic Operation

3.1. Answering a Call

3.2. Making a Call

3.3. End a Call

3.4. Call Records

3.5. Door Open Operation

4. Page Configuration

4.1. Ways to configure

Password Configuration

4.2. Setting via web browser

4.3. WEB Page Functional Explanation

Status

Wizard

Call Log

WAN Config

SERVICE PORT

SNTP

SIP Config

Voice Access Configuration

Door Card Setting

Call Log

5. Appendix

5.2、Owner Remote Opens the Voice Access Controller by VOIP Phone

5.3、Card Management

5.3.1

5.3.2

5.3.3

5.3.4、Add Remote Visit Data

Related manuals

Portech

IS-640

VoIPon

AG-188

VoIPon

AT-320 IAX2

ATCOM

AT840 series