Sharp PG-M20XU Service manual

PG-M20X
TENTATIVE
SERVICE MANUAL
SERVICE-ANLEITUNG
DIGITAL MULTIMEDIA PROJECTOR
DIGITALER MULTIMEDIA PROJEKTOR
MODEL
MODELLE
PG-M20X
In the interests of user-safety (Required by safety regulations in some countries) the set should be restored
to its original condition and only parts identical to those specified should be used.
Im lnteresse der Benutzersicherheit (erforderliche Sicherheitsregeln in einigen Ländern) muß das Gerät in seinen
Originalzustand gebracht werden. Außerdem dürfen für die spezifizierten Bauteile nur identische Teile verwendet
werden.
CONTENTS
Page
» SPECIFICATIONS ............................................. 2
» IMPORTANT SERVICE SAFETY
NOTES (for USA) ............................................... 3
» NOTE TO SERVICE PERSONNEL ................... 4
» OPERATION MANUAL ...................................... 7
» REMOVING OF MAJOR PARTS ..................... 13
» RESETTING THE TOTAL LAMP TIMER ......... 16
» ELECTRICAL ADJUSTMENT ........................... 19
» TROUBLE SHOOTING TABLE ........................ 25
» CHASSIS LAYOUT .......................................... 46
» BLOCK DIAGRAM ........................................... 48
» OVERALL WIRING DIAGRAM ........................ 50
» SCHEMATIC DIAGRAM .................................. 52
» PRINTED WIRING BOARD ASSEMBLIES ..... 98
» PARTS LIST
Ë ELECTRICAL PARTS ................................ 103
Ë CABINET AND MECHANICAL PARTS ..... 116
Ë ACCESSORIES PARTS ............................ 120
Ë PACKING PARTS ....................................... 120
» PACKING OF THE SET ................................. 121
SHARP CORPORATION
This document has been published to be used for
after sales service only.
The contents are subject to change without notice.
PG-M20X
Specifications
Product type Digital Multimedia Projector
Model PG-M20X
Video system NTSC 3.58/NTSC 4.43/PAL/PAL-M/PAL-N/PAL 60/SECAM/
DTV480I/DTV480P/DTV720P/DTV1080I
Display method Single Chip Digital Micromirror Device™ (DMD™) by Texas Instruments
DMD panel Panel size: 0.7" (17.8 mm), 1 chip XGA DMD
No. of dots: 786,432 dots (1,024 [H] × 768 [V])
Lens 1–1.2 × zoom lens, F1.75–2.04, f = 28.0–33.5 mm
Projection lamp High Intensity Discharge Lamp (HID Lamp), DC 210 W
Component input signal 29-pin connector
(INPUT1) DVI input signal: Digital 250–1,000 mV 50 Ω
Analog 0.7 Vp-p 75 Ω
Y: 1.0 Vp-p, sync negative, 75 Ω terminated
PB: 0.7 Vp-p, 75 Ω terminated
PR: 0.7 Vp-p, 75 Ω terminated
Horizontal resolution 700 TV lines (DTV720P)
Computer RGB input signal 29-pin connector
(INPUT 1) RGB separate/sync on green type analog input: 0–0.7 Vp-p, positive, 75 Ω terminated
HORIZONTAL SYNC. SIGNAL: TTL level (positive/negative)
VERTICAL SYNC. SIGNAL: Same as above
S-video input signal 4-pin Mini DIN connector
(INPUT 2) Y (luminance signal): 1.0 Vp-p, sync negative, 75 Ω terminated
C (chrominance signal): Burst 0.286 Vp-p, 75 Ω terminated
Video input signal RCA connector: VIDEO, composite video, 1.0 Vp-p, sync negative, 75 Ω
(INPUT 3) terminated
Pixel clock 12–230 MHz
Vertical frequency 43–100 Hz
Horizontal frequency 15–126 kHz
Audio input signal ø3.5 mm MINIJACK: AUDIO, 0.5 Vrms, more than 47 kΩ (stereo)
Audio output 2.0 W (monaural)
Speaker system 4 cm × 3 cm
Rated voltage AC 100–240 V
Input current 3.2 A
Rated frequency 50/60 Hz
Power consumption 290 W
Power dissipation <1,090 BTU/hour
Operating temperature 41°F to 95°F (+5°C to +35°C)
Storage temperature –4°F to 140°F (–20°C to +60°C)
Cabinet Plastic
I/R carrier frequency 38 kHz
Dimensions (approx.) 8 5⁄8" × 3" × 11 15⁄16" (219 (W) × 76 (H) × 303 (D) mm) (main body only)
8 3⁄4" × 3 1⁄4" × 12 1⁄2" (223 (W) × 83 (H) × 318 (D) mm) (including adjustment feet
and projecting parts)
Weight (approx.) 5.8 lbs. (2.6 kg)
Supplied accessories Remote control, Two R-03 batteries, Power cord for U.S., Canada etc. (6', 1.8 m), Power
cord for Europe, except U.K. (6', 1.8 m), Power cord for U.K., Hong Kong and Singapore (6',
1.8 m), Power cord for Australia, New Zealand and Oceania (6', 1.8 m), DVI to 15-pin D-sub
cable (6', 1.8 m), USB cable (6', 1.8 m), Carrying case, Lens cap (attached), Lens cap
strap, Terminal cover (attached), CD-ROM, Operation manual, Quick reference guides
Replacement parts Lamp unit (Lamp/cage module) (BQC-PGM20X//1), Remote control (RRMCGA013WJSA),
Two R-03 batteries (“AAA” size, UM/SUM-4, HP-16, or similar), Power cord for U.S., Canada
etc. (QACCDA007WJPZ), Power cord for Europe, except U.K. (QACCV4002CEZZ), Power
cord for U.K., Hong Kong and Singapore (QACCB5024CENA), Power cord for Australia,
New Zealand and Oceania (QACCL3022CEZZ), DVI to 15-pin D-sub cable
(QCNWGA010WJZZ), USB cable (QCNWG0001WJPZ), Carrying case
(GCASN0005CESA), Lens cap (CCAPHA001WJ01), Lens cap strap (UBNDT0013CEZZ),
Terminal cover (GCOVD0103CESA), CD-ROM (UDSKA0058CEN1), Operation manual
(TINS-7609CEZZ), Quick reference guides
This SHARP projector uses a DMD panel. This very sophisticated panel contains 786,432 pixels. As with any high technology electronic equipment such as large screen TVs, video
systems and video cameras, there are certain acceptable
tolerances that the equipment must conform to.
This unit has some inactive pixels within acceptable tolerances which may result in inactive dots on the picture screen.
This will not affect the picture quality or the life expectancy
of the unit.
Specifications are subject to change without notice.
2
PG-M20X
IMPORTANT SERVICE SAFETY NOTES (for USA)
Ë Service work should be performed only by qualified service technicians who are
thoroughly familiar with all safety checks and servicing guidelines as follows:
» Use an AC voltmeter with sensitivity of 5000 ohm
per volt., or higher, sensitivity to measure the AC
voltage drop across the resistor (See Diagram).
» All checks must be repeated with the AC plug
connection reversed. (If necessary, a non-polarized
adapter plug must be used only for the purpose of
completing these checks.)
Any reading of 0.3 volts RMS (this corresponds to
0.2 milliamp. AC.) or more is excessive and indicates
a potential shock hazard which must be corrected
before returning the unit to the owner.
WARNING
1. For continued safety, no modification of any circuit
should be attempted.
2. Disconnect AC power before servicing.
BEFORE RETURNING THE PROJECTOR:
(Fire & Shock Hazard)
Before returning the projector to the user, perform
the following safety checks:
1. Inspect lead wires are not pinched between the
chassis and other metal parts of the projector.
2. Inspect all protective devices such as non-metallic
control knobs, insulating materials, cabinet backs,
adjustment and compartment covers or shields,
isolation resistor-capacity networks, mechanical
insulators, etc.
3. To be sure that no shock hazard exists, check for
current leakage in the following manner:
» Plug the AC cord directly into a 120-volt AC outlet,
(Do not use an isolation transformer for this test).
» Using two clip leads, connect a 1.5k ohm, 10 watt
resistor paralleled by a 0.15µF capacitor in parallel
between all exposed metal cabinet parts and earth
ground.
AC
VOLTMETER
1.5k ohm (10W)
0.15µF
TEST PROBE
TO EXPOSED
METAL PARTS
CONNECT TO KNOWN
EARTH GROUND
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
SAFETY NOTICE
AVIS POUR LA SECURITE
Many electrical and mechanical parts in Projector have
special safety-related characteristics.
These characteristics are often not evident from visual
inspection, nor can protection afforded by them be
n e c e s s a r i l y i n c r e a s e d by u s i n g r e p l a c e m e n t
components rated for higher voltage, wattage, etc.
Replacement parts which have these special safety
characteristics are identified in this manual; electrical
components having such features are identified by “å”
and shaded areas in the Replacement Parts Lists and
Schematic Diagrams. For continued protection,
replacement parts must be identical to those used in
the original circuit. The use of a substitute replacement
parts which do not have the same safety characteristics
as the factory recommended replacement parts shown
in this service manual, may create shock, fire or other
hazards.
De nombreuses pièces, électriques et mécaniques, dans
les projecteur à présentent des caractéristiques
spéciales relatives à la sécurité, qui ne sont souvent
pas évidentes à vue.
Le degré de protection ne peut pas être nécessairement
augmentée en utilisant des pièces de remplacement
étalonnées pour haute tension, puissance, etc.
Les pièces de remplacement qui présentent ces
caractéristiques sont identifiées dans ce manuel;
les pièces électriques qui présentent ces particularités
sont identifiées par la marque “å” et hachurées dans
la liste des pièces de remplacement et les diagrammes
schématiques. Pour assurer la protection, ces pièces
doivent être identiques à celles utilisées dans le circuit
d’origine. L’utilisation de pièces qui n’ont pas les mêmes
caractéristiques que les pièces recommandées par
l’usine, indiquées dans ce manuel, peut provoquer des
électrocutions, incendies ou autres accidents.
WARNING: The bimetallic component has the primary
conductive side exposed. Be very careful in
handling this component when the power is on.
AVERTISSEMENT: La composante bimétallique dispose du
conducteur primaire dénudé. Faire
attention lors de la manipulation de cette
composante sous tension.
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
3
PG-M20X
NOTE TO SERVICE
PERSONNEL
12345678901234567890123456789012123456789012345
12345678901234567890123456789012123456789012345
NOTE POUR LE PERSONNEL
D’ENTRETIEN
12345678901234567890123456789012123456789012345
UV-RADIATION PRECAUTION
12345678901234567890123456789012123456789012345
12345678901234567890123456789012123456789012345
PRECAUTION POUR LES RADIATIONS UV
12345678901234567890123456789012123456789012345
12345678901234567890123456789012123456789012345
The light source, metal halide lamp, in the projector
emits small amounts of UV-Radiation.
La source de lumière, la lampe métal halide,
dans le projecteur émet de petites quantités de
radiation UV.
AVOID DIRECT EYE AND SKIN EXPOSURE.
EVITEZ TOUTE EXPOSITION DIRECTE
DES YEUX ET DE LA PEAU.
To ensure safety please adhere to the following:
Pour votre sécurité, nous vous prions de respecter
les points suivants:
1. Be sure to wear sun-glasses when servicing the
projector with the lamp
turned “on” and the top
enclosure removed.
1. Toujours porter des lunettes de soleil lors d’un
entretien du projecteur
avec la lampe allumée
et le haut du coffret retiré.
2. Do not operate the lamp outside of the lamp housing.
2. Ne pas faire fonctionner la lampe à l’extérieur du
boîtier de lampe.
3. Do not operate for more than 2 hours with the
enclosure removed.
3. Ne pas faire fonctionner plus de 2 heures avec le
coffret retiré.
UV-Radiation and Medium Pressure
Lamp Precautions
Précautions pour les radiations UV
et la lampe moyenne pression
1. Be sure to disconnect the AC plug when replacing
the lamp.
2. Allow one hour for the unit to cool down before
servicing.
3. Replace only with same type lamp. Type BQCPGM20X//1 rated 85V/210W.
4. The lamp emits small amounts of UV-Radiation,
avoid direct-eye contact.
5. The medium pressure lamp involves a risk of
explosion. Be sure to follow installation instructions
described below and handle the lamp with care.
1. To u j o u r s d é b ra n c h e r l a f i c h e AC l o r s d u
remplacement de la lampe.
2. Laisser l’unité refroidir pendant une heure avant de
procéder à l’entretien.
3. Ne remplacer qu’avec une lampe du même type.
Type BQC-PGM20X//1 caractéristique 85V/210W.
4. La lampe émet de petites quantités de radiation UVéviter tout contact direct avec les yeux.
5. La lampe moyenne pression implique un risque
d’explosion. Toujours suivre les instructions
d’installation décrites ci-dessous et manipuler la
lampe avec soin.
12345678901234567890123456789012123456789012345
4
PG-M20X
12345678901234567890123456789012123456789012345
12345678901234567890123456789012123456789012345
12345678901234567890123456789012123456789012345
12345678901234567890123456789012123456789012345
1234567890123456789012345678901212345678901234
UV-RADIATION PRECAUTION (Continued)
1234567890123456789012345678901212345678901234
1234567890123456789012345678901212345678901234
PRECAUTION POUR LES RADIATIONS UV (Suite)
12345678901234567890123456789012123456789012345
12345678901234567890123456789012123456789012345
12345678901234567890123456789012123456789012345
Lamp Replacement
Remplacement de la lampe
Note:
Remarque:
Since the lamp reaches a very high temperature
during units operation replacement of the lamp
should be done at least one hour after the power
has been turned off. (to allow the lamp to cool off.)
Installing the new lamp, make sure not to touch the
lamp (bulb) replace the lamp by holding its reflector
2.
[Use original replacement only.]
Comme la lampe devient très chaude pendant le
fonctionnement de l’unité, son remplacement ne doit
être effectué au moins une heure après avoir coupé
l’alimentation (pour permettre à la lampe de refroidir).
En installant la nouvelle lampe, s’assurer de ne pas
toucher la lampe (ampoule). Remplacer la lampe en
tenant son réflecteur 2.
[N’utiliser qu’un remplacement d’origine.]
1 Lampe
1 Lamp
2 Reflecteur
2 Reflector
DANGER ! –– Never turn the power on without the
lamp to avoid electric-shock or damage of the
devices since the stabilizer generates high voltages
at its start.
DANGER ! –– Ne jamais mettre sous tension sans
la lampe pour éviter un choc électrique ou des
dommages des appareils car le stabilisateur génère
de hautes tensions à sa mise en route.
Since small amounts of UV-Radiation are emitted
from an opening between the duct cover and the
lamp housing, it is recommended to place the LENS
CAP on the opening during servicing to avoid eye
and skin exposure (Fig. 1).
Comme de petites quantités de radiation UV sont
émises par une ouverture entre le couvercle du conduit et le botier de la lampe,il est recommandé de
placer le CAPUCHON D'OPTIQUE sur l'ouverture
pendant l'entretien pour éviter une exposition des
yeux et la peau (Fig. 1).
Note: Please obtain a lens cap before servicing a
models PG-M20X that is received without
one.
Remarque: Priére de se procurer un capuchon
d'optique acant d'entretien un modéle
PG-M20X qui est livré sans.
Figure 1.
Figure 1.
5
PG-M20X
WARNING:
High brightness light source, do not stare into the beam of light, or view directly. Be especially
careful that children do not stare directly in to the beam of light.
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS UNIT TO
MOISTURE OR WET LOCATIONS.
CAUTION
The lighting flash with arrowhead within
a triangle is intended to tell the user that
parts inside the product are risk of electric
shock to persons.
RISK OF ELECTRIC SHOCK.
DO NOT REMOVE SCREWS
EXCEPT SPECIFIED USER
SERVICE SCREWS
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE CABINET.
NO USER-SERVICEABLE PARTS EXCEPT LAMP UNIT.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
The exclamation point within a triangle is
intended to tell the user that important
operating and servicing instructions are
in the manual with the projector.
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
AVERTISSEMENT: Source lumineuse de grande intensité. Ne pas fixer le faisceau lumineux ou le regarder
directement. Veiller particulièrement à éviter que les enfants ne fixent directement le
faisceau lumineux.
AVERTISSEMENT: AFIN D’EVITER TOUT RISQUE D’INCENDIE OU D’ELECTROCUTION, NE PAS PLACER
CET APPAREIL DANS UN ENDROIT HUMIDE OU MOUILLE.
ATTENTION
L’éclair terminé d’une flèche à l’intérieur
d’un triangle indique à l’utilisateur que les
pi‘eces se trouvant dans l’appareil sont
susceptibles de provoquer une décharge
électrique.
RISQUE
D’ELECTROCUTION NE
PASRETIRER LES VIS, A
L’EXCEPTION DES VIS DE
REPARATION UTILISATEUR
SPECIFIEES
Le point d’exclamation à l’intérieur d’un
triangle indique à l’utilisateur que les
instr uctions de fonctionnement et
d’entretien sont détaillées dans les
documents fournis avec le projecteur.
ATTENTION: POUR EVITER TOUT RISQUE
D’ELECTROCUTION, NE PAS RETIRER LE CAPOT.
AUCUNE DES PIECES INTERIEURES N’EST REPARABLE
PAR L’UTILISATEUR, A L’EXCEPTION DE L’UNITE DE
LAMPE. POUR TOUTE REPARATION, S’ADRESSER A UN
TECHNICIEN D’ENTRETIEN QUALIFIE.
6
PG-M20X
Precautions for using lead-free solder
1 Employing lead-free solder
"Main PWB" of this model employs lead-free solder. The LF symbol indicates lead-free solder, and is attached on the
PWBs and service manuals. The alphabetical character following LF shows the type of lead-free solder.
Example:
LFa
Indicates lead-free solder of tin, silver and copper.
2 Using lead-free wire solder
When fixing the PWB soldered with the lead-free solder, apply lead-free wire solder. Repairing with conventional
lead wire solder may cause damage or accident due to cracks.
As the melting point of lead-free solder (Sn-Ag-Cu) is higher than the lead wire solder by 40ºC, we recommend you
to use a dedicated soldering bit, if you are not familiar with how to obtain lead-free wire solder or soldening bit,
contact our service station or service ranch in your area.
3 Soldering
As the melting point of lead-free solder (Sn-Ag-Cu) is about 220ºC which is higher than the conventional lead solder
by 40ºC, and as it has poor solder wettabillty, you may be apt to keep the soldering bit in contact with the PWB for
extended period of time. However, Since the land may be peeled off or the maximum heat-resistance temperature of
parts may be excoeded, remove the bit from the PWB as soon as you conurm the steady soldering condition.
Lead-free solder contains more tin, and the end of the soldering bit may be easily corroded. Make sure to tum on and
off the power of the bit as required.
if a different type of solder stays on the tip of the soldering bit, it is alloyed with lead-free solder. Clean the bit after
every use of it.
When the tip of the soldering bit is blackened during use, file it with steel wool or fine sandpaper.
Becareful when replacing parts with polarity indication on the PWB silk.
Lead-free wire solder for servicing
Part No.
ZHNDAi123250E
ZHNDAi126500E
ZHNDAi12801KE
★
J
J
J
Description
φ0.3mm
250g(1roll)
φ0.6mm
500g(1roll)
φ1.0mm
1kg(1roll)
7
Code
BL
BK
BM
PG-M20X
Location of Controls
Projector (Front and Top View)
LAMP REPLACEMENT
indicator
TEMPERATURE
WARNING indicator
Illuminates in green normally.
Replace the lamp when the
indicator illuminates in red.
Illuminates in green
normally. When the
internal temperature
rises, this indicator will
illuminate in red.
POWER indicator
Illuminates in red, when the
projector is in standby.
When the power is turned
on, this indicator will
illuminate in green.
INPUT button
For switching input mode
1, 2 or 3.
MENU button
Turns the power on or off.
For displaying adjustment
and setting screens.
LENS button
VOLUME buttons
For adjusting Keystone or
Digital Shift setting.
For adjusting the
speaker sound level.
Adjustment buttons
(
)
UNDO button
POWER button
For undoing an operation
or returning to the default
settings.
For selecting menu items.
ENTER button
AUTO SYNC button
For setting items selected
or adjusted on the menu.
For automatically
adjusting images when
connected to a computer.
AV MUTE button
For temporarily turning off the
sound and picture.
Focus ring
Zoom knob
Terminal cover
Speaker
Remote control
sensor
Foot releases/Adjustment
feet
For adjusting the projector’s
height.
Attaching the terminal cover
Attach the terminal cover by
placing it on the side panel of the
projector and pressing it into
place, as shown in the illustration.
8
PG-M20X
Projector (Side View)
INPUT 1 terminal
USB terminal
Port for DVI digital, computer
RGB, and COMPONENT
signals.
For connecting a computer using a USB cable.
INPUT 2 terminal
INPUT AUDIO terminal
Shared audio terminal for
INPUT 1, INPUT 2, and
INPUT 3.
Terminal for connecting video
equipment with an S-VIDEO
terminal.
AC socket
INPUT 3 terminal
For connecting video
equipment.
Exhaust vent
Kensington Security
Standard connector
Using the Kensington Lock
• This projector has a Kensington Security Standard connector for use with a Kensington MicroSaver Security
System. Refer to the information that came with the system for instructions on how to use it to secure the
projector.
Attaching the lens cap
After putting the lens cap strap on the
lens cap, pass the other end of the strap
through the hole under the projector, next
to the lens, as shown in the illustration.
Bottom View
9
PG-M20X
Remote Control
Remote control signal transmitter
FORWARD/BACK button
POWER button
Moves forward or backwards
when connected to a computer
using a USB cable. Same as the
[Page Down] and [Page Up]
keys on a computer keyboard.
Turns the power on or off.
ENLARGE (Enlarge/Reduce)
buttons
For enlarging or reducing part of the
image.
AV MUTE button
For temporarily turning off the
sound and picture.
FREEZE button
For freezing images.
INPUT 3 button
VOLUME buttons
For switching the input mode to
INPUT 3.
For adjusting the speaker
sound level.
RESIZE button
INPUT 2 button
For switching the screen size
(NORMAL, BORDER, etc).
For switching the input mode to
INPUT 2.
GAMMA button
INPUT 1 button
For correcting the brightness of an
image, when the images displayed
are hard to see because of the
brightness of the room. Four
gamma modes are available to
choose from.
For switching the input mode to
INPUT 1.
AUTO SYNC button
For automatically adjusting
images when connected to a
computer.
MENU button
For displaying adjustment and
setting screens.
LENS button
For adjusting Keystone or
Digital Shift setting.
Adjustment buttons
(
)
ENTER button
For selecting menu items.
For setting items selected or
adjusted on the menu.
UNDO button
For undoing an operation or
returning to the default settings.
10
PG-M20X
Connection Pin Assignments
DVI Digital / Analog INPUT 1 port : 29 pin connector
• DVI Digital INPUT
9
•••••••••
1 2
••••
Pin No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
~ • • • • • • • • • 16
~ •••• 7 8
C1
C2
C4
C5
C3
17
24
18
••••
~
••••
23
• DVI Analog RGB Input
Pin No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Signal
Not connected
Not connected
Not connected
Not connected
Not connected
DDC clock
DDC data
Vertical sync
Not connected
Not connected
Not connected
Not connected
Not connected
+5V current
Ground
Signal
T.M.D.S data 2–
T.M.D.S data 2+
T.M.D.S data 2 shield
Not connected
Not connected
DDC clock
DDC data
Not connected
T.M.D.S data 1–
T.M.D.S data 1+
T.M.D.S data 1 shield
Not connected
Not connected
+5V current
Ground
Pin No.
16
17
18
19
20
21
22
23
24
C1
C2
C3
C4
C5
• DVI Analog Component Input
Pin No.
16
17
18
19
20
21
22
23
24
C1
C2
C3
C4
C5
Signal
Hot plug detection
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
Analog input Red
Analog input Green
Analog input Blue
Horizontal sync
Ground
Pin No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Signal
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
Ground
Pin No.
16
17
18
19
20
21
22
23
24
C1
C2
C3
C4
C5
4-pin USB connector
• USB connector: 4 pin B-type USB connector
2
1
3
4
Signal
Hot plug detection
T.M.D.S data 0–
T.M.D.S data 0+
T.M.D.S data 0 shield
Not connected
Not connected
T.M.D.S clock shield
T.M.D.S clock+
T.M.D.S clock–
Not connected
Not connected
Not connected
Not connected
Ground
Pin no.
1
2
3
4
Signal
VCC
USB–
USB+
SG
Name
USB current
USB data–
USB data+
Signal Ground
11
Signal
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
Analog input Pr/Cr
Analog input Y
Analog input Pb/Cb
Not connected
Ground
PG-M20X
Dimensions
Rear View
Side View
Top View
12 9/16
(318.3)
Side View
11 15/16
(302.5)
8 3/4 (223)
8 5/8 (219)
5 1/16 (128)
Front View
1 1/2
3 1/4
3
(38.7) (76.1) (82.9)
3/8
1
(34.2)
4 9/16 (115.5)
7 11/16 (195)
3 1/4 (82.5)
3/16
2
(55.5)
3 1/ 8
(80)
Bottom View
2 3/8
(60)
5/16
(7.5)
4 1/ 8
(104)
10 5/16
(261.5)
Units: inches (mm)
12
PG-M20X
REMOVING OF MAJOR PARTS
1. Removal of the top body
1-1. Detach the terminal block cover.
1-2. Remove the five lock screws from the top body.
1-3. Slightly lift the front of the top body and disconnect the speaker connector.
2. Removal of the power PWB unit and cooling fan
2-1.
2-2.
2-3.
2-4.
Disconnect the specified connectors.
Detach the cooling fan.
Remove the four lock screws from the power unit.
Remove the three lock screws from the PFC PWB.
Top body
1-2
1-2
1-3
1-1
1-2
2-3
1-2
1-2
Terminal cover
Power Unit
2-1
2-4
PFC Unit
2-1
2-2
Cooling fan
13
PG-M20X
3. Removal of the PC I/F PWB and input PWB
3-1.
3-2.
3-3.
3-4.
3-5.
Disconnect the specified connectors.
Remove the three lock screws and two hex screws from the PC I/F PWB.
Disconnect the connector from the input PWB.
Remove the three lock screws from the input PWB.
Remove the lock screw from the terminal block cover.
3-2
3-1
PC I/F Unit
3-3
3-4
Input Unit
3-3
3-5
3-2
14
PG-M20X
4. Removal of the operation PWB, optical unit and ballast unit
4-1.
4-2.
4-3.
4-4.
Disconnect the specified connectors from each PWB.
Remove the two lock screws from the operation PWB.
Remove the six lock screws from the optical unit.
Remove the lock screw from the ballast unit.
5. Removal of the formatter PWB
5-1. Remove the two lock screws from the heat sink.
5-2. Remove the four lock screws from the backer plate assembly, and detach the formatter PWB.
4-1
4-2
4-2
KEY Unit
4-3
Optical mechanism Unit
4-4
Ballast Unit
4-1
Bottom body
Formatter Unit
Backer plate Assy
5-1
DMD Unit
Heat sink
15
5-1
PG-M20X
RESETTING THE TOTAL LAMP TIMER
■ The warning lights on the projector indicate problems inside the projector.
■ If a problem occurs, either the TEMPERATURE WARNING indicator or the LAMP REPLACEMENT
indicator will illuminate red, and the power will turn off. After the power has been turned off, follow
the procedures given below.
TEMPERATURE
WARNING
indicator
POWER
indicator
LAMP
REPLACEMENT
indicator
About the TEMPERATURE WARNING indicator
If the temperature inside the projector increases, due to blockage of the air vents, or
” will blink in the
the setting location, “
lower left corner of the picture. If the temperature keeps on rising, the lamp will turn
off and the TEMPERATURE WARNING indicator will blink, the cooling fan will run for
further 90 seconds, then the power will be
shut off. After “
” appears, be sure to
perform the following measures.
About the
LAMP
REPLACEMENT
indicator
■ When the lamp
exceeds 1,900 cumulative hours
” will be displayed
of use, “
on the screen in yellow. When
the cumulative hours of use
” will
reach 2,000, “
change to red, the lamp will automatically turn off and then the
projector as well. At this time, the
LAMP REPLACEMENT indicator will illuminate in red.
■ If you try to turn on the projector
a fourth time without replacing
the lamp, the projector will not
turn on.
Maintenance indicator
Condition
Problem
Possible Solution
Abnormal
Normal
• Relocate the projector to an area
• Blocked air intake
with proper ventilation.
TEMPERAThe internal
TURE
•
Take
the projector to your nearest
•
Cooling
fan
breaktemperature is
Red on/
WARNING
Off
Sharp
Authorized Projector Dealer
down
Power off abnormally high.
indicator
• Internal circuit failure or Service Center for repair.
• Clogged air intake
LAMP
REPLACEMENT
indicator
Green on
Green
blinks
when the
lamp is
active.
Red
blinks
Time to change
the lamp
• Lamp usage time
exceeded 1,900
hours
Red on/
Power off
The lamp does
not illuminate.
• Burnt-out lamp
• Lamp circuit failure
• Take the projector to your nearest
Sharp Authorized Projector Dealer
or Service Center for repair or
lamp replacement.
• Please exercise care when
replacing the lamp.
Info
• If the LAMP REPLACEMENT indicator illuminates, and the power turns off, follow the above possible solutions and then wait until the projector has cooled down completely before plugging in the power cord and
turning the power back on. (At least 5 minutes.)
• If the power is turned off and then turned on again, as during a brief test, the LAMP REPLACEMENT indicator may be triggered, preventing the power from going on. Should this occur, take the power cord out of the
wall outlet and plug it back in again.
• If you want to clean the air vents during projector operation, be sure to first press
and after the power
has turned off and the cooling fan has stopped, then clean the vents.
• Do not unplug the power cord after the power has been turned off and while the cooling fan is running. The
cooling fan runs for about 90 seconds.
16
PG-M20X
Lamp
■ It is recommended that the lamp (sold separately) be replaced after approximately 1,900 cumulative
hours of use or when you notice a significant deterioration of the picture and color quality. The
lamp usage time can be checked with the on-screen display. See page 58.
■ For lamp replacement, please consult your nearest Sharp Authorized Projector Dealer or Service
Center.
IMPORTANT NOTE TO U.S. CUSTOMERS:
The lamp included with this projector is backed by a 90-day parts and labor limited warranty. All service
of this projector under warranty, including lamp replacement, must be obtained through a Sharp Authorized Projector Dealer or Service Center. For the name of the nearest Sharp Authorized Projector Dealer
U.S.A. ONLY
or Service Center, please call toll-free: 1-888-GO-SHARP (1-888-467-4277).
Caution Concerning the Lamp
■ This projector utilizes a pressurized mercury lamp. A loud sound may indicate lamp failure. Lamp
failure can be attributed to numerous sources such as: excessive shock, improper cooling, surface
scratches or deterioration of the lamp due to a lapse of usage time. The period of time up to failure
largely varies depending on the individual lamp and/or the condition and the frequency of use. It is
important to note that failure can often result in the bulb cracking.
■ When the LAMP REPLACEMENT indicator and on-screen display icon are illuminated or flash, it is
recommended that the lamp be replaced with a new one immediately, even if the lamp appears to be
operating normally.
■ Should the lamp break, the glass particles may spread inside the lamp cage or gas contained in the
lamp may be vented into the room from the exhaust vent. Because the gas in this lamp includes
mercury, ventilate the room well if the lamp breaks and avoid all exposure to the released gas. In
case of exposure to the gas, consult with a doctor as soon as possible.
■ Should the lamp break, there is also a possibility that glass particles may spread inside of the
projector. In such a case, it is recommended you contact your nearest Sharp Authorized Projector
Dealer or Service Center to remove the damaged lamp and assure safe operation.
Replacing the Lamp
Caution
• Do not remove the lamp unit immediately after operation of the projector. The lamp will be hot and touching
it can lead to burn or injury.
• Wait at least one hour after the power cord is disconnected to allow the surface of the lamp unit to fully cool
before removing the lamp unit.
■ If the new lamp does not light after replacement, take your projector to the nearest Sharp Authorized Projector Dealer or Service Center for repair. Purchase a replacement lamp unit of type BQCPGM20X//1 from your nearest Sharp Authorized Projector Dealer or Service Center. Then carefully
change the lamp by following the instructions described in this section. If you wish, you may have
the lamp replaced at your nearest Sharp Authorized Projector Dealer or Service Center.
17
PG-M20X
How to Release the System Lock
Turn on the power. If the system lock is applied, the system-resetting screen appears. Press the following keys in this
order.
MENU → ENTER → ENTER → MENU → UNDO → UNDO → MENU
After pressing the MENU key first, press the remaining six keys within 10 seconds.
18
PG-M20X
ELECTRICAL ADJUSTMENT
No.
Adjustment Items
Adjustment Conditions
Adjustment Procedures
1
Initialization of
EEPROM
1. Turn on the power (the lamp lights
up) and warm up the system for 15
minutes.
1. Carry out the following setting.
Press SW2001 to enter the process
mode, and execute S2 on SSS menu.
2
Adjustment of CW
index
1. Signal input: 64-step color bar
2. Select the following group and subject.
Group: DLP
Subject: Select CW-INDEX.
1. Feed the signal to INPUT 1.
2. Select subject and make adjustment
so that the lamp gradation patterns
of R, G and B should be smooth without noise.
R
G
B
3
Adjustment of
RGB gradation
reproduction
1. Feed the SMPTE pattern signal.
2. Select the following group and subject.
Group: DLP
Subject: G1-GAIN
1. Confirm that 100% and 95% white
gradation, and 0% and 5% black gradation are discernible.
2. If the white gradation looks differently,
do fine adjustment by G1-GAIN.
4
Adjustment of
video brightness/
contrast
1. Feed the NTSC100% window patter signal. (Burst signal)
2. Select the following group and subject.
Group: VIDEO
Subject: AUTO
1. After signal input, select AUTO using the set's switch or the remote
controller's button for automatic adjustment.
5
Adjustment of
video tint
1. Feed the split color bar signal.
2. Select the following group and subject.
Group: VIDEO
Subject: TINT
1. Confirm the fixed value.
Fixed value: 128
19
PG-M20X
No.
Adjustment Items
Adjustment Conditions
Adjustment Procedures
6
Adjustment of
NTSC color
saturation
1. Feed the internal 8ch (split color bar)
signal.
2. Select the following group and subject.
Group: VIDEO
Subject: N-COLOR
1. Confirm the fixed value.
Fixed value: 59
7
Adjustment of PAL 1. Feed the PAL color bar signal.
color saturation
2. Select the following group and subject.
Group: VIDEO
Subject: P-COLOR
1. Confirm the fixed value.
Fixed value: 59
8
Adjustment of
SECAM color
saturation
1. Feed the SECAM color bar signal.
2. Select the following group and subject.
Group: VIDEO
Subject: S-COLOR
1. Confirm the fixed value.
Fixed value: 59
9
Adjustment of
COMPO G brightness
1. Input signal: 0% gray pattern signal (480I)
2. Select the following group and subject.
Group: COMPO
Subject: G-BRIGHT
1. Feed the signal to INPUT 1.
Make adjustment so that some bits
should be missing in the picture.
10
Adjustment of
COMP CR-Offset
1. Feed the color difference signal
(480I): Y 0% brightness, Cb and Cr
0% white patterns.
Group: COMPO
Subject: AUTO
1. After signal input, select AUTO using the set's switch or the remote
controller's button for automatic adjustment.
11
Automatic Adjustment of RGB
white balance
1. Feed the 50% gray pattern signal
(XGA, 60 Hz).
2. Select the following group and subject.
Group: DLP
Subjects: R1-GAIN (Red)
B1-GAIN (Blue)
1. Adjust R-1 GAIN and B1-GAIN so that
x-value should be 266±3 and y-value
320±3.
12
Automatic Adjustment of SRGB
white balance
1. Feed the 50% gray pattern signal
(XGA, 60 Hz).
2. Select the following group and subject.
Group: DLP
Subjects: S-R1-GAIN (Red)
S-G1-GAIN (Green)
S-B1-GAIN (Blue)
1. Set the value of S-R1-GAIN to 34.
2. Adjust S-G1-GAIN and S-B1-GAIN
so that x-value should be 310±3 and
y-value 335±3.
20
PG-M20X
No.
Adjustment Items
Adjustment Conditions
Adjustment Procedures
13
Automatic adjustment of video
white balance
1. Feed the 50% gray pattern signal
(NTSC, burst signal).
2. Select the following group and subject.
Group: DLP
Subjects: V-R1-GAIN (Red)
V-B1-GAIN (Blue)
1. Adjust V-R1-GAIN and V-B1-GAIN so
that x-value should be 265±3 and yvalue should be 298±3.
14
Automatic adjust- 1. Feed the 50% gray pattern signal
ment of DTV white
(480I, color difference signal).
balance
2. Select the following group and subject.
Group: DLP
Subjects: C-R1-GAIN
C-B1-GAIN
1. Adjust C-R1-GAIN and C-B1-GAIN
so that x-value should be 263±3 and
y-value should be 295±3.
15
Adjustment of
DLP voltage (For
reference)
1. Read voltage rank of DLP description.
2. Set the switch corresponding to the
rank which has been read. (on the
formatter PWB)
1. Carry out adjustment when DLP chip
has been replaced or combination of
chip and formatter has been changed.
2. Rank:
B C D E
Setting value: 1 2 3 4
16
Confirmation and
re-adjustment of
white balance
1. The adjusting conditions for each
item are as follows:
For RGB input, see Item 11
For SRGB input, see Item 13
For video input, see Item 14
For DVT input, see Item 12
Confirm that there is no deviation in white
balance from that of the monitoring
equipment.
For readjustment, proceed in the order
of RGB input, video input and DTV input.
17
Confirmation of
color-related
operation
1. Receive the color bar signal.
1. Select L1 in the process mode.
Check the performance of color and
tint.
18
Confirmation of
picture-related
operation
1. Receive monoscope pattern signal.
1. Select L2 in the process mode.
Check Picture, Brightness and Sharpness.
19
Confirmation of
RGB
1. Receive the RGB signal.
1. Select L4 on the process mode.
Check Picture, Brightness, Red, Blue,
Clock, Phase, H-POS and V-POS.
20
Confirmation of
off-timer operation
21
Confirmation of
thermistor operation
1. Select OFF in the process mode.
Confirm that the off-timer starts with
5-minute display, counts 1 minute for
1 second, and turns off when 0 minute
is displayed.
1. Heat the thermistor by dryer.
21
1. Confirm that the temperature is displayed.
PG-M20X
No.
Adjustment Items
Adjustment Conditions
Adjustment Procedures
22
Automatic sync
operation
1. Receive the phase checking pattern
signal.
1. Confirm that Clock, Phase, H-POS
and V-POS can be automatically
adjusted in the VGA/S-VGA/XGA
mode.
23
Confirmation of
USB operation
Connect the set to a personal computer
by USB cable.
Using the remote controller, make sure
that feed and return operations are effective on the display of the personal
computer.
24
Factory settings
1. Make the following settings.
Process
adjustment
S4
Remote controller
settings
"Factory Setting 4"
How to Adjust the PC I/F unit
1. Initialization of EEPROM
1) Press SW2002 to enter the process mode.
2) Execute S1 on the SSS menu. (By S1, all the contents of EEPROM are initialized.)
3) Confirm that the program version "Ver. XXX" has become the latest one
2. Adjusting items
1) Adjustment of RGB drive/gain
(1) feed the window pattern signal that has 100% and 0% signals.
(2) Select AUTO among the A/D items in the process mode and carry out adjustment.
22
PG-M20X
» Adjustment mode process menu
Group
Adjust PC Image
A/D
Sub Group
Adjust DLP Image
DLP
Adjust VIDEO Image
VIDEO
Adjust Component Image
DTV
Process mode
LINE
INTIAL SETTING
SSS
Sample Pattern
PATTERN
23
Subject
R-BRIGHT
G-BRIGHT
B-BRIGHT
R-D
B-D
G-D
AD-AUTO
R1-BLK
R1-GAIN
G1-BLK
G1-GAIN
B1-GAIN
CW-INDEX
S-R1-GAIN
S-G1-GAIN
S-B1-GAIN
C-R1-GAIN
C-B1-GAIN
V-R1-GAIN
V-B1-GAIN
PICTURE
BRIGHT
TINT
N-COLOR
P-COLOR
S-COLOR
STAT-GAIN
VIDEO-AUTO
G-BRIGHT
CB-OFFSET
CR-OFFSET
COMPO-AUTO
L1
L2
L3
OFF
TEMP OFF
SENSOR CHECK
TIME
S1
S2
S3
S4
S5
RGB
RGB(50)
CROSS
SETP
COLOR
CHR
PG-M20X
Group
Adjust CVIC
Sub Group
CVIC-PROGRSSIVE
Subject
MODE
IP
MDSW
PTGSW
C-TESTSW
C-ILG-LY
C-MOD-LY
C-VE-LV
ENH-PLUS
ENH-MINUS
DFC
ENH-PLUS
ENH-MINUS
DFC
ENH-PLUS
ENH-MINUS
DFC
CUBIC-RGB
CUBIC-VEDEO
YNR-LEVEL
YNR-K
YNR-FSEL
CNR-LEVEL
CNR-K
CNR-FSEL
CNR-FILSW
TBL-NO
RED
YELLOW
GREEN
VYAN
BLUE
MAGENTA
IPL
IPL2
E2PROM
ADR RD/WR
CVIC-ENHANCE-VIDE
CVIC-ENHANCE-HTTV
CVIC-ENHANCE-RGB
CVIC-SCREEN
CVIC-NR
CVIC-PTG
CVIC-CMS
Version Check etc
Special
24
PG-M20X
TROUBLE SHOOTING TABLE
Checking of Basic Operation
Does the POWER LED light up or
flicker in red or green?
No
Go to "Checking of Power Unit".
Yes
Does the set operate by the set's
key or the remote controller's
power key?
No
Go to "Checking of Sub-microcomputer
and Its Periphery"
Yes
Does the cooling fan rotate and
does the lamp light up?
No
Go to "Checking of Lamp Lighting-up"
Yes
Is the user menu displayed?
No
Check the formatter circuit and
its periphery.
No
Check IC8013 (AD) and go to
"Checking of RGB Input".
No
Check IC8015 and peripheral
circuit.
No
Is there input signal at pins
(8), (17) and (23) of IC8013?
No
Check IC3851 and its
peripheral circuit.
No
Go to "Checking of Video
Input". Is there input signal at
the emitter of Q8002?
No
Check IC3502 and its
peripheral circuit.
Yes
Does the RGB input operate
normally?
Yes
Does the video input operate
normally?
Yes
Do the component input/DVI input
operate normally?
Yes
Does the DVI input operate
normally?
Yes
End
Yes
Check IC8015 and its
peripheral circuit.
25
PG-M20X
Checking of Power Unit
Are connectors in the power unit
completely inserted?
No
Insert the connectors CN702,
CN704, CN7003, CN7001,
CN7004 and CN7101 completely.
No
Close the lamp door completely by
screws.
No
Replace the bimetal switch, or rest
it by pressing the red button.
Yes
Is the lamp door closed
completely?
Yes
Is the bimetal switch turned off?
Yes
Is AC voltage applied across relay
RL7001?
No
Replace F701.
Yes
Is there DC voltage of about 6V at
pin (1) of CN7002?
No
Check Q7501, Q7502 and Q7503
and their peripheral circuits. If any
circuit is damaged, replace it.
No
Check the circuits connected to the
primary side of T701. If any circuit
is damaged, replace it.
No
Check the circuits connected to the
secondary side of T701. If any
circuit is damaged, replace it.
Yes
Is there DC voltage of about 370V
across CN702?
Yes
Is there rated voltage at the output
terminals of CN7001 and CN7102?
Yes
Check the PWB circuits of relevant
output sides.
26
PG-M20X
Lamp Does Not Light Up.
Is any of SC9001, SC9002, P9002
and P9003 connectors
disconnected or in poor contact?
Yes
Insert the connectors completely.
No
Is an appropriate voltage supplied
to SC9002?
No
Go to "Checking of Input PWB"
Yes
Is there the 180-Hz pulse signal at
pin (1) of P9002?
Yes
Go to "Checking of Lamp" and
"Checking of Ballast"
No
Go to "Color Wheel Does Not
Rotate."
No
Is the color wheel rotating?
Yes
Is there the 180-Hz pulse signal at
pin (2) of P9003 when no input
signal is given?
No
Go to "Checking of Input PWB"
Yes
Is the signal at pin (10) of IC9101
at High level?
No
Go to "Checking of PC I/F unit"
Yes
No
Is the signal at pin (9) of IC9101
at High level?
No
Are the signals at pins (69) and
(70) at High level?
Yes
Yes
Trouble with 1C9101 or its
peripheral part.
Trouble with IC9003
27
PG-M20X
Lamp does not light up.
Yes
Is the cooling fan rotating?
No
Check the power circuit or the fan
circuit on the key/input PWB.
No
Check IC3101, the motor driver
circuit and their periphery.
Check the waveform of SC3101.
Yes
Is the color wheel rotating sound
heard?
Yes
Normal
Replace the color
wheel.
Is the lamp discharging sound
heard?
Yes
Abnormal
Check the
formatter PWB.
Check the socket
No
No
Replace the lamp.
Is DC 34V voltage applied across
the ballast power?
No
Check the power circuit.
Yes
Is voltage higher than 3.5V applied
to pin (19) of P9002 on the
formatter PWB?
No
Check IC9101 and its periphery
on the formatter PWB.
Yes
Check the ballast power.
28
PG-M20X
Checking of Sub-microprocessor
and Its Periphery
Does POWER LED flicker in red
(for 2 seconds)?
No
Yes
Is there B+3.3V output at pins (12)
and (13) of CN3701?
Yes
No
Is there 6V output at pins (5) and
(6) of P2003?
No
Go to "Checking of PC I/F Unit", and check
the flexible connector.
Communication error of sub-microprocessor
(KEY) and SH microprocessor (PC I/F unit)
Pins (20) and (21) of P2001.
Check Q2001 thru Q2004 of
IC2001.
Yes
Go to "Checking of Power Unit"
Is Bu+6.2V signal outputted?"
No
Go to "Checking of
Power Unit"
No
Check IC2010 and its
periphery.
No
Check IC2002 and its
periphery.
Yes
Is Bu+3.3V signal outputted?
Yes
Is 3.3V signal output at pin
(19) of IC2001?
Yes
Check IC2001 and its
periphery and go to
"Checking of Remote Control
Communication".
29
PG-M20X
Checking of Low-pass Filter Circuit
Is video signal is inputted to pins
(4), (8) and (12) of IC3851?
No
Check pins (4), (8) and (12) of
SC3001.
Normal
Yes
Check Q3854 and
Q3855.
Is video signal inputted to pins
(24), (21) and (17) of IC3851?
Check the PC I/F unit.
Check DVI (analog)
input.
No
IC3851 is defective.
If the picture quality is abnormal, check whether
or not the following voltages are outputted to
pin (28) of IC3851.
0.3 V for 480i, 1 V for 720p, 1080i, Check IC301.
No
Check Q3851, Q3852 and Q3853
and their periphery.
No
Is the video signal inputted to pins
(8), (17) and (23) of IC8013
(AD9888) of the PC I/F unit?
Yes
Is video signal is inputted to pins
(16), (20) and (24) of SC3001?
Abnormal
Yes
The low-pass filter circuit on the
input PWB is normal. Does the
picture appear?
Yes
End
Yes
Check the SOG
circuit or IC8013
and its periphery.
30
No
Check IC8013
and its periphery.
PG-M20X
Checking of DTV
(480i Component Input)
Feed the 480i component signal in INPUT 1.
Select INPUT 1 using the set's key or the remote controller.
Select 480i among the special modes on the user
menu screen.
Go to "Checking of
Low-pass Filter Circuit"
Yes
Yes
Is picture outputted?
No
Confirmation of synchronization.
Is Y signal including sync signal
inputted to pin (3) of IC2502?
No
Is the signal type set to the
component?
Check IC8016
(Video decoder).
Yes
Is the color normal?
Yes
No
Yes
No
Check IC3501 and its
periphery.
Set the signal type.
In case of monitor output,
disconnect the monitor output
cable.
Abnormal
Restored to normal condition
Set the monitor output.
Check the monitor output
equipment and cable.
Does the contour of picture
appear clear.
Yes
End
No
Is 480i selected among the special
modes?
Yes
IC8025 is defective.
31
No
Select 480i.
PG-M20X
Checking of Video Input
Feed the composite video signal to
INPUT 3. Select INPUT 3 using the
set's key or the remote controller.
Does the picture appear?
Yes
Is the picture disturbed?
No
Are pin(5) (horizontal) and
pin(10) (vertical) signals
inputted to IC8363 on the
PC I/F unit?
Yes
No
No
Yes
1
Is the video signal including sync
Yes
signal inputted to pin (3) of SC3001
on the input PWB?
Check IC8363 and
IC8025 (CVIC2) and
their periphery.
Check IC8016 (video decoder)
of PC board and its periphery.
Check Q8002.
No
Is the video signal including sync
Yes
signal inputted to pin (7) of SC3502
on the input PWB?
Check Q3512 and Q3513 on
the input PWB.
No
1
Check IC3502 and its peripheral
circuit.
No
Feed the S-video signal to INPUT 2.
Select INPUT 2 using the set's key
or the remote controller. Does the
picture appear?
Yes
Yes
Is the color normal?
Yes
End
32
No
Is the C signal inputted
to pin (11) of SC3001?
No
Check Q3502 on the
input PWB.
PG-M20X
» FORMATTER Unit
Abnormal picture
Blackout
Rainbow-like picture
Others
No
No
Go to "Lamp Does Not
Light Up."
Is signal outputted at
pins (3), (5) and (7) of
SC9001?
No
Is the lamp on?
Go to "Checking of PC I/F nunit"
Yes
Trouble with IC9003,
IC9006 or their periphery
Is any of SC9001, SC9002, P9002
and P9003 connectors
disconnected or in poor contact?
Yes
Insert the connectors
completely.
No
Is an appropriate voltage supplied
to SC9002?
No
Go to "Checking of Input PWB"
Yes
Reassemble the DMD, optical
mechanism and formatter unit.
Is the symptom improved?
Yes
End
No
Is the voltage at the positive-polarity
pin of C9066 appropriate (+7V)?
No
Trouble with peripheral circuit
of C9066 or trouble with IC9003
No
Trouble with peripheral circuit
of C9068 or trouble with IC9003
No
Trouble with peripheral circuit
of C9562 or trouble with IC9003
Yes
Is the voltage at the positive-polarity
pin of C9068 appropriate (+23 to +26V)?
Yes
Is the voltage at the negative-polarity
pin of C9562 appropriate (-26V)?
Yes
Trouble with the DMD
33
Yes
PG-M20X
» PC I/F Unit-1/12
Checking of PC PWB
0
Yes
Is the user menu displayed?
No
Check the onscreen display.
Check the RGB input.
Check the component input.
Check the video input.
Check the DVI digital input.
PCカードのチェック
Check the PC card.
End
34
PG-M20X
» PC I/F Unit-2/12
Checking of Onscreen Display
Is the user menu displayed
normally by the MENU key?
Yes
The onscreen display is normal.
No
Enter the process menu and select
PATTERN. Then select the
COLOR pattern.
Is the onscreen display color
normal?
No
Adjust the DLP system in the
process adjustment mode.
Yes
0
Make STEP signal selection.
Is the STEP signal normal?
Yes
Rewrite the onscreen display data.
No
0
Is the signal compatible with the
STEP signal outputted at TL106
thru TL111?
No
IC8025 is defective.
Yes
Go to "Checking of GA4 and Its
Periphery".
Rewrite the onscreen display data.
35
PG-M20X
» PC I/F Unit-3/12
Checking of RGB Input
Feed the sync separation type
analog RGB signal to INPUT 1.
1
Select INPUT 1 using the set's
key or the remote controller.
2
Does the picture appear?
No
Go to "Confirmation of
Video Input".
Yes
Is the picture disturbed?
Yes
Go to "Checking of Sync Signal".
No
3
Do the three colors R, G and B
appear?
No
Go to "Checking of RGB Signal".
Yes
Carry out the AUTOSYNC process.
Is the contour of picture clear?
No
Yes
Is there any disturbance in the
vertical stripe pattern?
Yes
IC8013, 8025 or its periphery is
defective.
No
End
36
PG-M20X
» PC I/F Unit-4/12
Confirmation of Video Input
Make "Confirmation of Input
Signal Setting".
Is there video signal at the land
of C8070?
No
Is there signal at the terminal C2 of
P8001 (DVI connector)?
Yes
Yes
Somewhere in the signal route is
defective. Check the capacitors and
resistors between the connector
and IC8013.
Go to "Checking of Sync Signal".
IC8025 or IC8013 is defective.
The signal source or connector
is defective.
Confirmation of Input Signal Setting
Is the input menu selected
correctly?
No
Select the input menu correctly.
Yes
2
Are the connectors connected
correctly?
No
Connect the connectors correctly.
Yes
1
End
37
No
PG-M20X
» PC I/F Unit-5/12
Checking of Sync Signal
Is there the vertical sync signal at
pin (11) of IC8363?
No
Yes
Is there the horizontal sync signal
at pin (5) of IC8363?
No
Make confirmation of input signal
setting.
Yes
IC8330, IC8331 or its periphery
is defective.
Is there the vertical sync signal at
TL8131?
No
Yes
Is there the horizontal sync signal
at TL8130?
No
IC8363 is defective.
Yes
Are both the vertical and horizontal
signals in appropriate timing?
Yes
The sync signal is normal.
End of checking.
No
Is the signal generator
(input source) appropriate?
No
Set the signal source appropriately.
Yes
2
IC8330, IC8331 or its periphery
is defective.
38
PG-M20X
» PC I/F Unit-6/12
Checking of R, G and B Signals
Is the signal type set to RGB?
No
Yes
Set the signal type to RGB.
Set the process mode.
Select R, G and B individually on
the pattern menu.
Go to "Checking of GA4 and Its
Periphery".
For checking the input signal,
set the signal generator to
gradation signal.
Check TL8169, TL8170 and
TL8180 by oscilloscope.
(MSB bit after A/D conversion)
Are there the specified signals at
TL8169, TL8170 and TL8180?
No
Does the signal come to C8062,
C8070 and C8078?
Yes
IC8025 and its periphery are
defective.
No
Yes
IC8013 and its periphery are
defective.
39
Go to "Confirmation of
Video Input".
PG-M20X
» PC I/F Unit-7/12
Checking of GA4 and Its Periphery
Select R, G and B individually on
the pattern menu in process mode.
Is picture outputted appropriately
in R, G and B?
Yes
Checking of GA4 and its periphery
ends.
No
Check pins (72), (52) and (32) of
SC8001 by oscilloscope.
These signals are MSB of B/G/R.
Do the signals selected on the
pattern menu match with those
checked by oscilloscope?
Yes
The DLP PWB is defective.
No
Does the clock signal come to pin
(78) of SC8001?
No
Is there the clock (32.5 MHz)
signal at TL8114?
Yes
Yes
No
IC8029 is defective.
Is there the clock (32.5 MHz)
signal at TL8110?
No
Yes
X8005 is defective.
Check TL8106, TL8107, TL8108,
TL8109, TL81010 and TL81011
by oscilloscope.
Do the signals selected on the
pattern menu match with those
checked by oscilloscope?
IC8025 is defective.
No
IC8025 is defective.
Yes
IC8029 is defective.
40
PG-M20X
» PC I/F Unit-8/12
Checking of Component Input
(except 480I)
Feed the component signal to
INPUT 1.
Select INPUT 1 using the set's
key or the remote controller.
Is the picture appear?
No
Go to "Checking of SOG Circuit".
Yes
4
Is the color normal?
No
Is the signal type set at component?
No
Yes
Set the signal type to component.
Carry out the process adjustment.
4
Is the contour of picture clear?
No
IC8013 or IC8025 is defective.
Yes
The component is normal. End.
41
PG-M20X
» PC I/F Unit-9/12
Checking of SOG Circuit
Check pin (2) of IC8365 by
oscilloscope.
Is the composite sync signal
reproduced in correct timing?
Yes
The SOG circuit is normal.
End.
No
Go to "Confirmation of Input
Signal Setting".
No
Check the land of C8070 by
oscilloscope.
Is there the Y signal including sync
signal?
Yes
The SOG sync separation circuit
(input PWB) is defective.
42
PG-M20X
» PC I/F Unit-10/12
Checking of Video Input
Feed the composite video signal to
INPUT 3.
Select INPUT 3 using the set's key
or the remote controller.
5
Is the picture appear?
No
Go to "Checking of Video
Sync Signal".
Yes
Is there any disturbance in the
picture?
Yes
No
Go to "Checking of Video
Sync Signal".
Carry out the process
adjustment.
No
Is the color normal?
5
Yes
The video input is normal. End.
Is the video signal inputted to
C8141?
No
Is there the specified signal
at R114?
Yes
Yes
Check the clock signal of IC8015
by FL8114.
Is the clock signal normal?
No
Q8003 and its periphery are
defective.
No
IC8015 is defective.
Yes
Go to "Checking of Video Sync
Signal".
IC8025 and its periphery are
defective.
43
Input PWB is defective.
PG-M20X
» PC I/F Unit-11/12
Checking of Video Sync Signal
Check pin (10) of IC8363 by
oscilloscope.
(Checking of vertical sync signal)
Is the vertical sync signal normal?
No
Yes
Check pin (6) of IC8363 by
oscilloscope.
(Checking of horizontal sync signal)
Is the horizontal sync signal
normal?
No
Go to "Confirmation of Input Signal
Setting".
No
IC8015 and its periphery are
defective.
No
IC8015 and its periphery are
defective.
Yes
Are the horizontal sync signal and
vertical sync signal outputted at
TL8130 and TL8131?
Yes
Is there the specified clock
(13.5 MHz) signal at FL114?
Yes
End
44
PG-M20X
» PC I/F Unit-12/12
Checking of DVI Digital Input
Feed the DVI digital signal to
INPUT 1.
Select INPUT 1 for input.
Is the picture appear?
No
Yes
Is there any disturbance in the
picture?
No
Yes
Is the color normal?
No
IC8298 and its periphery are
defective.
Yes
The DVI digital input is normal.
Check pin (13) of IC8363 for vertical
sync signal, and check pin (3) of
IC8363 for horizontal sync signal.
Are the sync signals normal?
No
Yes
Check R8685 for clock signal.
Is the clock signal normal?
No
IC8298 and its periphery are
defective.
Yes
IC8025 and its periphery are
defective.
45
PG-M20X
CHASSIS LAYOUT
H
G
F
E
D
C
B
A
1
2
3
46
4
5
6
7
8
9
10
11
47
12
PG-M20X
BLOCK DIAGRAM
GY
EA
6MHz
SCL
SDA
IC 3301
Audio AMP
AUDIO
VOL
S+,S-
LEARN
AG_MENU
VOL
S/VIDEO
S/COMP
LPF720P
SOGSEL
S/VIDEO
S/COMP
LPF720P
AUDIO-IN
Video
IC2001
RS232C/RF
L_CLICK
R_CLICK
PLUGGED
R/C
DAC
Reg.
2.5V,3.3V
5V,12VM
FAN
CONT3
Sub-MCU
AG_CLK
AG_DATA
IC 3502
SW
VIDEO
FAN 1 VCC
FANERR
FANPOW
Reg.
PFCCON
FANCONT4
FANPOW
IC3002
FAN3
FAN5
Reg.
Reg.
7.38MHz
KEY3,2,1,0 (Analog)
POW
IC2005
SW
KEY
LED(STBY,POW,
LAMPG,LAMPR.TEMP)
TXD2,RXD2
FANCONT1
F
FAN2
Reg.
13V
6V
2.5V
3.3V
D+,D-
FAN1
Reg.
FAN
CONT2
F4
IC 3202
E2PROM
G
USB
FANERROR
FANPOW
FAN4
USB-Controller
(CYPRESS)
PLUGGED
BU+5V
USB_5V
Reg.
GYRO UNIT
WIRED R/C
IC 3201
F1
RF-DATA
STREAM_A_CLK,DATA
STATUS,USB_PWR
B+CYPRESS
KEY UNIT
F2
ANT_49
IC 5803
Packet Flaming
PIC
POWER UNIT
F3
SYN_ENE,DATA,CLK
Filter
IC 2002
Reset
13V
BU6V
PCON 0
PCON 1
F5
RF_ON
EB
Reg.
KY
Filter
455kHz
IC 5801
FM Receiver
KY
Rod Antenna
GY
H
LED
FANCONT1
S-C
S-Y
S-Video
AGCLK,AGDATA
PCON1
G
INPUT UNIT
G
IC 3901~3
SOG
Sync sep.
S+,S-
S
IC 3851
LPF
Reg.
BU5V
BU5V
RS232C/RF,L_CLICK,R_CLICK
S+,STXD1,RXD1
PLUGGED
RST_SYS
TH3001
Temp.
IC 3101
Motor Controller
12VM
R/C
SCL,SDA
RST_SYS
TXD1,RXD1
TXD2,RXD2
TEMP2
BU5V
5V
3.3V
2.5V
6V
PCON1
S-Y
S-C
VIDEO
GSYNC
R,G,B
DTVR,G,B
CN1
E
FB
M
FAN_1_VCC
12VM
3.3V
5V
2.5V
MTRSIDO
MTRSIDI
MTRSICLK
MTRSICSZ
MTRCLK
MTRRSTZ
CN1
Reg. 1.9V,1.8V
R/C
VIDEO
S-C
PC-BOARD
CS,RAS,
CAS,WE
BA1,BA1
A[0:10]
DQM[0:3]
DQ[0:31]
CARDVCC
VCC3VEN
IC8367
SH3-Bus Bridge
AD_SCL,AD_SDA
DDP_SCL,DDP_SCL
2
3
48
4
5
CTM
CTMN
400MHz
3.3V
IC 9004
FLASH
5V
CONTROL(10)
IC 9005
Voltage
Generator
RDRAM
128Mbit
VRST -26V
VBIAS +23~+26V
VCC2+7.5V
DMD
IC9507
Phase
Reset
Driver
ASIC
MBSRT
[15:0]
+7.5V
5V
N_LIGHT
LAMPLIT
BALLAST
ECO
TEMP1
7
LAMPEN
LAMP_POW
132.7MHz(Core)
6
IC 9001
Clock Generator
FLAD[19:0]
FLD[15:0]
Control(5 wired)
VRSTEN
VBIASEN
VCC2EN
DDP_LIGHT
32.768KHz
SCLI,SCLO,SDAI,SDAO
IRQ5,10,14
1
DDP1000
ASIC
PCLKM
SCLKM
50MHz
IC 9006
PWRGOOD
RESETZ
16.58MHz
IC 8007
Main-MCU(SH3)
WAIT
WAIT_CARD
D[15:0]
A[23:0]
CTL
D[15:0]
A[23:0]
CTL
OE
WE
IC 8005
FLASH
4M×16bit
DDP_SDA
DDP_SCL
DQA[8:0]
RQ[7:0],RQB[7:0]
D
Reg.
MEMR
MEMW
SYSCK
DLPTM
Data Processor
FA
D[15:0]
A[23:0]
CTL
D[31:0]
A[23:0]
CTL
3.3VC
Card Slot
Interface
CN2
PC
Card
Slot
CN2
PCMCIA TYPE II Card
IC8002
RD,WE1
CKIO
D[15:0]
A[23:0]
CTL
CPU BUS(65.5MHz)
AD_SCL
AD_SDA
60MHz
OUTPUT
IC 9003
Comparator
12V
1.8V,3.3V
IN1IN2/RGBSEL
CD[15:0]
CA[25:0]
CONTROL
5V
DD[63:0]
DCLK (60MHz)
LOADB_LZ,TRC_L
Serial Bus(4 wired)
100MHz
SYSTEM
IC 8003
E2PROM
FA
Panel
Link
Panel
Controler
RST_SYS
TXD1,RXD1
TXD2,RXD2
TEMP2
SCL,SDA
IC8028 IC8030
SDRAM
4M×(16+16)
PODCK
CLKIN
VSYNCZ
HSYNCZ
ACTDATA
BU[9:0]
GY[9:0]
RV[9:0]
GA4_RST
SI_H,V
B
Photo
Sensor
DMD FORMAT UNIT
IC 8029
GA4
RESET
PDE
A
FB
1.9V
GPEN,GCLP,GCOAST
GHS2
GCLK
GRO[7:0],GRE[7:0]
GGO[7:0],GGE[7:0]
GBO[7:0],GBE[7:0]
PDE
A/D
Amp
PLL
DTVR,G,B
R,G,B
IC8298
GHSYNR
DCLK
DVS
DHS
DRO[9:0]
DRE[9:0]
DGO[9:0]
DGE[9:0]
DBO[9:0]
DBE[9:0]
RESET
H,V
IC8011
E2PROM
RX2+,RX2RX1+,RX1RX0+,RX0RXC+,RXC-
IC 8025
CVIC 2
IC 8013
IC 8363
SW
SENSOR
UNIT
CWINDEX
S
W
IC8330~IC8331
Comparator
802.11b SS W-LAN
or
FLASH ATA
MEMORY
IC8319~
IC8322
SDRAM
GSYNC
PCH,PCV
R,G,B
DVI
25MHz
VH,VV
DVI
C
32.5MHz
IN1IN2/RGBSEL
D
Digital
Video
Decoder
24.576MHz
Color Wheel
CW
IC 8015
CLK
CW
VY[8]
VUV[8]
ITLC
VAO
VCLK
VH,VV
CWY[3..1]
CWCTR
8
TH 9003 Temp.
9
10
11
49
12
PG-M20X
OVERALL WIRING DIAGRAM
H
G
F
E
D
C
B
A
1
2
3
50
4
5
6
7
8
9
10
11
51
12
PG-M20X
DESCRIPTION OF SCHEMATIC
DIAGRAM
BESCHREIBUNG DES
SCHEMATISCHEN SCHALTPLANS
VOLTAGE MEASUREMENT CONDITION:
SPANNUNGSMESSUNGEN:
1. Voltages at test points are measured at the supply
voltage of AC 230V. Signals are fed by a colour bar
signal generator for servicing purpose and the above
voltages are measured with a 20k ohm/V tester.
1. Spannungen an den Prüfpunkten werden bei einer
Netzspannung von 230V gemessen, Signale werden
für die Wartung mit einem Farbbalken-Signal
generator zugeführt, und Spannungen werden mit
einem Meßinstrument (20 kΩ/V) ermittelt.
WAVEFORM MEASUREMENT CONDITION:
SIGNALFORMMESSUNGEN:
1. Waveforms at test points are observed at the supply
voltage of AC 230V. Signals are fed by a colour bar
signal generator for servicing purpose.
1. Die Wellenformen an den Testpunkten werden bei
einer Netzspannung von 230V verfolgt. Signale
werden für die Wartung mit einem Farbbalken-Signal
generator zugeführt.
INDICATION OF RESISTOR & CAPACITOR:
BEZEICHNUNG DES WIDERSTANDS UND
KONDENSATORS:
RESISTOR
1. The unit of resistance “Ω” is omitted.
(K=kΩ=1000 Ω, M=MΩ).
2. All resistors are ± 5%, unless otherwise noted.
(J= ± 5%, F= ± 1%, D= ± 0.5%)
3. All resistors are 1/16W, unless otherwise noted.
4. All resistors are Carbon type, unless otherwise
noted.
W : Cement
C : Solid
S : Oxide Film
T : Special
N : Metal Coating
CAPACITOR
1. All capacitors are µF, unless otherwise noted.
(P=pF=µµF).
2. All capacitors are 50V, unless otherwise noted.
3. All capacitors are Ceramic type, unless otherwise
noted.
(ML): Mylar
(TA): Tantalum
(PF): Polypro Film
(ST): Styrol
WIDERSTAND
1. Die Widerstandseinheit “Ω” wird weggelassen.
(K=kΩ=1000 Ω, M=MΩ).
2. Alle Widerstände haben ± 5%, sofern nicht anders
angegeben.
(J= ± 5%, F= ± 1%, D= ± 0.5%)
3. Alle Widerstände haben 1/16W, sofern nicht anders
angegeben.
4. Alle Widerstände sind Kohletyp, sofern nicht anders
angegeben.
W : Zement
C : Fest
S : Oxidefilm
T : Spezial
N : Metallüberzug
KONDENSATOR
1. Die Kapazitätseinheit ist µF, sofern nicht anders
angegeben.
(P=pF=µµF).
2. Alle Kondensatoren haben 50V, sofern nicht anders
angegeben.
3. Alle Kondensatoren sind Keramiktyp, sofern nicht
anders angegeben.
(ML): Mylar
(TA): Tantal
(PF): Polyprofilm
(ST): Styrol
CAUTION:
This circuit diagram is original one, therefore there may be a
slight difference from yours.
ACHTUNG:
bei diesem Schaltplan handelt es sich um den ursprünglichen.
Esönnen daher geringfügige Unterschiede zu dem lhrem bestehen.
SAFETY NOTES:
1. DISCONNECT THE AC PLUG FROM THE AC
OUTLET BEFORE REPLACEING PARTS.
2. SEMICONDUCTOR HEAT SINKS SHOULD BE
REGARDED AS POTENTIAL SHOCK HAZARDS
WHEN THE CHASSIS IS OPERATING.
SICHERHEITSANMERKUNGEN:
1. VOR DEM AUSWECHSELN VON TEILEN MUSS
U N B E D I N G T N E T Z S T E C K E R AU S D E R
NETZSTECKDOSE GEZOGEN WERDEN.
2. DIE WARMEABLEITER DER HALBLEITER SOLLTEN
BEIM BETRIEB DES CHASSIS ALS MÖGLICHE
URSACHEN VON GEFÄHRLICHEN ELEKTRISCHEN
SCHLÄGEN BETRACHTET WERDEN.
IMPORTANT SAFETY NOTICE:
PARTS MARKED WITH “ å (
) ARE
IMPORTANT FOR MAINTAINING THE SAFETY OF
THE SET. BE SURE TO REPLACE THESE PARTS
WITH SPECIFIED ONES FOR MAINTAINING THE
SAFETY AND PERFORMANCE OF THE SET.
WICHTIGE SICHERHEITSANMERKUNGEN:
MIT “ å (
)BEZEICHNETEN TEILE SIND
BESONDERS WICHTIG FÜR DIE AUFRECHTERHALTUNG
DER SICHERHEIT . BEIM WECHDIESER TEILE SOLLTEN
DIE VORGESCHRIEBENEN TEILE IMMER VERWENDET
WERDEN, UM SOWOHL DIE SICHERHEIT ALS AUCH DIE
LEISTUNG DES GERÄTES AUFRECHTZUERHALTEN.
52
PG-M20X
WAVEFORMS
1 SC3101 1-pin
(INPUT CWCTR)
H : 200µ sec/div
V : 6.90V/div
2 SC3101 3-pin
(INPUT CWY2)
H : 200µ sec/div
V : 6.90V/div
3 P9002 1-pin
(FORMAT LAMPEN)
H : 2m sec/div
V : 1.64V/div
4 P9003 2-pin
(FORMAT CWINDEX)
H : 2m sec/div
V : 1.64V/div
5 SC9001 3-pin
(FORMAT CLKIN)
H : 400µ sec/div
V : 870mV/div
6 SC9001 5-pin
(FORMAT HSYNC)
H : 10µ sec/div
V : 880mV/div
7 SC9001 7-pin
(FORMAT VSYNC)
H : 4m sec/div
V : 880mV/div
8 SC9002 17-pin
(FORMAT MTRSICLK)
H : 2µ sec/div
V : 1.44V/div
9 SC9002 25-pin
(FORMAT MTRCLK)
H : 40m sec/div
V : 1.44V/div
0 IC8363 7-pin
(PC-BOARD PCH)
H : 10µ sec/div
V : 840mV/div
q IC8363 1-pin
(PC-BOARD PCV)
H : 4m sec/div
V : 840mV/div
w SC3001 3-pin
(INPUT VIDEO)
H : 10µ sec/div
V : 180mV/div
e SC3001 11-pin
(INPUT S-C)
H : 20µ sec/div
V : 1.44V/div
r SC3001 8-pin
(INPUT PCGIN2)
H : 10µ sec/div
V : 180mV/div
t SC3001 20-pin
(INPUT GLPF)
H : 10µ sec/div
V : 230mV/div
y SC3001 30-pin
(INPUT C-SYNC)
H : 10µ sec/div
V : 840mV/div
53
PG-M20X
Ë FORMATTER UNIT-1/5
H
G
F
E
D
C
B
A
1
2
3
54
4
5
6
7
8
9
10
11
55
12
PG-M20X
Ë FORMATTER UNIT-2/5
H
G
F
E
D
C
B
A
1
2
3
56
4
5
6
7
8
9
10
11
57
12
PG-M20X
Ë FORMATTER UNIT-3/5
H
G
F
E
D
C
B
A
1
2
3
58
4
5
6
7
8
9
10
11
59
12
PG-M20X
Ë FORMATTER UNIT-4/5
H
G
F
E
D
C
B
A
1
2
3
60
4
5
6
7
8
9
10
11
61
12
PG-M20X
Ë FORMATTER UNIT-5/5
H
G
F
E
D
C
B
A
1
2
3
62
4
5
6
7
8
9
10
11
63
12
PG-M20X
Ë INPUT UNIT-1/5
H
G
F
E
D
C
B
A
1
2
3
64
4
5
6
7
8
9
10
11
65
12
PG-M20X
Ë INPUT UNIT-2/5
H
G
F
E
D
C
B
A
1
2
3
66
4
5
6
7
8
9
10
11
67
12
PG-M20X
Ë INPUT UNIT-3/5
H
G
F
E
D
C
B
A
1
2
3
68
4
5
6
7
8
9
10
11
69
12
PG-M20X
Ë INPUT UNIT-4/5
H
G
F
E
D
C
B
A
1
2
3
70
4
5
6
7
8
9
10
11
71
12
PG-M20X
Ë INPUT UNIT-5/5
H
G
F
E
D
C
B
A
1
2
3
72
4
5
6
7
8
9
10
11
73
12
PG-M20X
Ë KEY UNIT-1/3
H
G
F
E
D
C
B
A
1
2
3
74
4
5
6
7
8
9
10
11
75
12
PG-M20X
Ë KEY UNIT-2/3
H
G
F
E
D
C
B
A
1
2
3
76
4
5
6
7
8
9
10
11
77
12
PG-M20X
Ë KEY UNIT-3/3
H
G
F
E
D
C
B
A
1
2
3
78
4
5
6
7
8
9
10
11
79
12
PG-M20X
Ë POWER UNIT
H
G
F
E
D
C
B
A
1
2
3
80
4
5
6
7
8
9
10
11
81
12
PG-M20X
Ë PFC UNIT
H
G
F
E
D
C
B
A
1
2
3
82
4
5
6
7
8
9
10
11
83
12
PG-M20X
Ë PC I/F UNIT-1/7
H
G
F
E
D
C
B
A
1
2
3
84
4
5
6
7
8
9
10
11
85
12
PG-M20X
Ë PC I/F UNIT-2/7
H
G
F
E
D
C
B
A
1
2
3
86
4
5
6
7
8
9
10
11
87
12
PG-M20X
Ë PC I/F UNIT-3/7
H
G
F
E
D
C
B
A
1
2
3
88
4
5
6
7
8
9
10
11
89
12
PG-M20X
Ë PC I/F UNIT-4/7
H
G
F
E
D
C
B
A
1
2
3
90
4
5
6
7
8
9
10
11
91
12
PG-M20X
Ë PC I/F UNIT-5/7
H
G
F
E
D
C
B
A
1
2
3
92
4
5
6
7
8
9
10
11
93
12
PG-M20X
Ë PC I/F UNIT-6/7
H
G
F
E
D
C
B
A
1
2
3
94
4
5
6
7
8
9
10
11
95
12
PG-M20X
Ë PC I/F UNIT-7/7
H
G
F
E
D
C
B
A
1
2
3
96
4
5
6
7
8
9
10
11
97
12
PG-M20X
PRINTED WIRING BOARD ASSEMBLIES
H
G
F
E
D
C
B
A
PC I/F Unit (Side-A)
1
2
3
4
98
5
6
PG-M20X
H
G
F
E
D
C
B
A
PC I/F Unit (Side-B)
1
2
3
4
99
5
6
PG-M20X
H
G
FORMATTER Unit (Side-A)
F
E
D
INPUT Unit (Side-A)
C
B
A
KEY Unit (Side-A)
1
2
3
4
100
5
6
PG-M20X
H
G
FORMATTER Unit (Side-B)
F
E
D
INPUT Unit (Side-B)
C
B
A
KEY Unit (Side-B)
1
2
3
4
101
5
6
PG-M20X
H
G
F
POWER Unit (Side-A)
E
D
POWER Unit (Side-B)
C
B
A
PFC Unit (Component Side)
1
2
3
4
102
5
6
PG-M20X
Ref. No.
Part No.
★
Description
PARTS LIST
Code
Ref. No.
Part No.
★
Description
Code
ERSATZTEILLISTE
PARTS REPLACEMENT
AUSTAUSCH VON TEILEN
Parts marked with "å" are important for maintaining the safety of
the set. Be sure to replace these parts with specified ones for maintaining the safety and performance of the set.
Ersatzteile, die besondere Sicherheitseigenschften haben, sind in
dieser Anleitung markiert. Elektrische Komponenten mit solchen
Eigenshaften sind in den Ersatzteil durch "å" gekenn-zeichnet.
Der Gebrauch von Ersatzteilen, die nicht deselben Sicherheitseigenschaften haben wie die vom Hersteller empfohlenen ud in der
Bedienungsanleitung angegebenen, können zur Ursache von
Blitzeinschlägen, Bränden und anderen Gefahren werden.
"HOW TO ORDER REPLACEMENT PARTS"
To have your order filled promptly and correctly, please furnish the
following informations.
"WIE MAN ERSATSTEILE BESTELLT"
in USA:
1. MODEL NUMBER
2. REF. NO.
3. PART NO.
4. DESCRIPTION
5. CODE
6. QUANTITY
Damit Ihre Bestellung promt und korrekt ausgeführt wird, geben Sie
bitte folgende Informationen.
1. MODELL NR.
3. ERSATZTEIL NR.
5. KODE
Contact your nearest SHARP Parts Distributor.
For location of SHARP Parts Distributor,
Please call Toll-Free; 1-800-BE-SHARP
2. REF. NR.
4. BESCHREIBUNG
6. QUANTITÄT
in CANADA: Contact SHARP Electronics of Canada Limited
Phone (416) 890-2100.
★ MARK: SPARE PARTS-DELIVERY SECTION
Ref. No.
Part No.
★
Description
★ MARKIERUNG : ERSATZTEILE-LIEFERUNG
Code
Ref. No.
Part No.
★
Description
PRINTED WIRING BOARD ASSEMBLIES
DUNTKB065DE01
(NOT REPLACEMENT ITEM)
FORMATTER UNIT
DUNTKB065DE01
DUNTKB066DE01
DUNTKB067DE01
RDENCA004WJZZ
RDENCA010WJZZ
CPCi-0057CE01
RDENCA005WJZZ
J
Formatter Unit
Input Unit
Key Unit
Power Unit
PFC Unit
PC I/F Unit
Ballast Unit
(Unit Replacement)
Code
INTEGRATED CIRCUITS
—
—
—
—
—
—
BZ
IC9001
IC9003
IC9004
IC9005
IC9006
IC9007
IC9101
IC9504
IC9505
IC9506
IC9507
IC9510
IC9511
VHiTCDCR83D-1
RH-iXA089WJZZ
RH-iXA090WJZZ
VHiLT1613CS-1
VHiK4R271S8-1
VHiLP3962M1-1
VHiAHCT08PW-1
VHiOPA237NA-1
VHiLM321MF+-1
VHiOPA237NA-1
RH-iXA005WJZZ
VHi4040CM35-1
VHi4040CM35-1
Q9001
Q9002
Q9003
Q9101
Q9102
Q9501
Q9502
Q9503
Q9504
Q9505
Q9506
Q9507
Q9508
Q9509
Q9510
Q9511
D9005
VS2SJ356+++-1
VS2SC4672Q/-1
VS2SC3928AR-1
VS2SC3928AR-1
VS2SC3928AR-1
VSMMBT2907A-1
VSMMBT2907A-1
VSMMBT2222A-1
VSMMBT2907A-1
VSMMBT2222A-1
VSMMBT2907A-1
VSiMT17++++-1
VSUMH4N++++-1
VSUMH4N++++-1
VSFDG6303N+-1
VSFDG6303N+-1
VHDMi1A3///2E
D9006
D9007
D9008
TH9003
VHDMi1A3///2E
VHDMi1A3///2E
VHDSFPA73//2E
RH-HXA001WJZZ
J
J
J
J
J
J
J
J
J
J
J
J
J
TCDCR83D
IC
IC
LT1613CS
K4R271S8
LP3962M1
AHCT08PW
OPA237NA
LM321MF
OPA237NA
IC
4040CM35
4040CM35
TRANSISTORS
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
2SJ356
2SC4672Q
2SC3928AR
2SC3928AR
2SC3928AR
MMBT2907A
MMBT2907A
MMBT2222A
MMBT2907A
MMBT2222A
MMBT2907A
IMT17
UMH4N
UMH4N
FDG6303N
FDG6303N
Diode
AE
AB
AB
AB
AC
DIODES AND THERMISTER
J
J
J
J
Diode
Diode
Diode
Thermister
PACKAGED CIRCUITS AND COIL
X9001 RCRUAA001WJZZ
103
J Crystal
AC
AC
AD
PG-M20X
Ref. No.
★
Part No.
Description
Code
DUNTKB065DE01
FORMATTER UNIT(Continued)
X9002 RCRUAA002WJZZ
L9001 RCiLP0191GEZZ
J Crystal
J Peaking Coil
CAPACITOES
C9001
C9002
C9003
C9004
C9006
C9007
C9008
C9009
C9010
C9011
C9013
C9014
C9015
C9016
C9019
C9021
C9022
C9023
C9024
C9025
C9026
C9027
C9028
C9029
C9030
C9032
C9034
C9035
C9036
C9037
C9038
C9039
C9041
C9042
C9043
C9044
C9045
C9046
C9047
C9049
C9050
C9051
C9053
C9054
C9055
C9056
C9057
C9058
C9059
C9060
C9061
C9062
C9063
C9064
C9065
C9066
C9067
C9068
C9069
C9070
C9071
C9072
C9073
C9075
C9101
C9102
C9503
C9505
VCEAPF1CW106M
VCKYCY1EF104Z
VCKYCY1EF104Z
VCKYCY1EF104Z
VCKYCY1EF104Z
VCKYCY1EF104Z
VCCCCY1HH680J
VCKYCY1EF104Z
VCCCCY1HH680J
VCKYCY1EF104Z
VCKYCY1EF104Z
VCKYCY1EF104Z
VCKYCY1EF104Z
VCKYCY1EF104Z
VCSNDE0GP107M
VCKYCY1EF104Z
VCEAPF1CW106M
VCKYCY1CB104K
VCCCCY1HH680J
VCKYCY1EF104Z
VCCCCY1HH680J
VCKYCY1EF104Z
VCEAPF1HW105M
VCKYCY1CB104K
VCCCCY1HH4R0C
VCKYCY1CB104K
VCKYCY1CB104K
VCKYCY1EF104Z
VCKYCY1EF104Z
VCEASH1VN106M
VCKYCY1CB104K
VCKYCY1HF104Z
VCKYCY1CB104K
VCKYCY1EF104Z
VCKYCY1CB104K
VCKYCY1EF104Z
VCKYCY1CB104K
VCEASH1VN106M
VCKYCY1HF104Z
VCEASH1VN106M
VCKYCY1EF104Z
VCKYCY1HF104Z
VCKYCY1CB104K
VCCCCY1HH7R0D
VCKYCY1EF104Z
VCEAPV1EW475M
VCKYCY1CB104K
VCEAPF1EW475M
VCKYCY1CB104K
VCKYCY1EF104Z
VCKYCY1CB104K
VCKYCY1CB104K
VCSNDE0GP107M
VCEAPF1HW105M
VCEAPF1CW106M
VCEAPF1HW335M
VCEAPF1CW106M
VCEAPF1HW335M
VCSNDE0GP107M
VCKYCY1HF104Z
VCKYCY1EF104Z
VCKYCY1EF104Z
VCKYCY1EF104Z
VCEAPF1HW105M
VCKYCY1EF104Z
VCKYCY1EF104Z
VCKYCY1EF104Z
VCKYCY1EF104Z
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
10
0.1
0.1
0.1
0.1
0.1
68p
0.1
68p
0.1
0.1
0.1
0.1
0.1
100
0.1
10
0.1
68p
0.1
68p
0.1
1.0
0.1
4.0p
0.1
0.1
0.1
0.1
10
0.1
0.1
0.1
0.1
0.1
0.1
0.1
10
0.1
10
0.1
0.1
0.1
7.0p
0.1
4.7
0.1
4.7
0.1
0.1
0.1
0.1
100
1.0
10
3.3
10
3.3
100
0.1
0.1
0.1
0.1
1.0
0.1
0.1
0.1
0.1
16V
25V
25V
25V
25V
25V
50V
25V
50V
25V
25V
25V
25V
25V
4.0V
25V
16V
16V
50V
25V
50V
25V
50V
16V
50V
16V
16V
25V
25V
35V
16V
50V
16V
25V
16V
25V
16V
35V
50V
35V
25V
50V
16V
50V
25V
25V
16V
25V
16V
25V
16V
16V
4.0V
50V
16V
50V
16V
50V
4.0V
50V
25V
25V
25V
50V
25V
25V
25V
25V
Electrolytic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
AB
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
Ceramic
Electrolytic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Electrolytic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Electrolytic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Electrolytic
Ceramic
Electrolytic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Electrolytic
Ceramic
Electrolytic
Ceramic
Ceramic
Ceramic
Ceramic
AA
AB
AB
AA
AA
AA
AA
AB
AB
AA
AB
AB
AA
AA
AB
AA
AA
AC
AB
AB
AB
AA
AB
AB
Electrolytic
Electrolytic
Electrolytic
Electrolytic
Electrolytic
AB
AB
AB
AB
AB
Ceramic
Ceramic
Ceramic
Ceramic
Electrolytic
Ceramic
Ceramic
Ceramic
Ceramic
AA
AA
AA
AB
AA
AA
AA
AA
AB
AB
AA
AB
AA
AB
Ref. No.
★
Part No.
C9510
C9511
C9513
C9514
C9515
C9516
C9517
C9519
C9520
C9521
C9522
C9523
C9524
C9525
C9527
C9528
C9529
C9530
C9531
C9532
C9533
C9535
C9536
C9537
C9538
C9539
C9542
C9544
C9545
C9546
C9547
C9548
C9549
C9550
C9551
C9552
C9553
C9554
C9555
C9558
C9562
C9563
C9564
C9565
C9566
C9567
VCKYCY1EF104Z
VCKYCY1EF104Z
VCKYCY1EF104Z
VCKYCY1EF104Z
VCKYCY1EF104Z
VCKYCY1EF104Z
VCKYCY1EF104Z
VCKYCY1EF104Z
VCKYCY1EF104Z
VCKYCY1EF104Z
VCKYCY1EF104Z
VCEAPF1CW106M
VCKYCY1EF104Z
VCKYCY1EF104Z
VCKYCY1HF104Z
VCKYCY1EF104Z
VCKYCY1EF104Z
VCKYCY1EF104Z
VCKYCY1EF104Z
VCKYCY1EF104Z
VCKYCY1EF104Z
VCKYCY1EF104Z
VCKYCY1EF104Z
VCKYCY1EF104Z
VCKYCY1EF104Z
VCKYCY1EF104Z
VCKYCY1EF104Z
VCKYCY1EF104Z
VCKYCY1EF104Z
VCKYCY1EF104Z
VCKYCY1EF104Z
VCKYCY1EF104Z
VCKYCY1EF104Z
VCKYCY1EF104Z
VCKYCY1EF104Z
VCKYCY1EF104Z
VCKYCY1EF104Z
VCKYCY1EF104Z
VCKYCY1EF104Z
VCEAPF0GW227M
VCEAPF1HW335M
VCKYCY1EF104Z
VCKYCY1EF104Z
VCKYCY1EF104Z
VCKYCY1EF104Z
VCKYCY1EF104Z
R9001
R9003
R9005
R9006
R9007
R9008
R9010
R9011
R9014
R9017
R9018
R9020
R9031
R9032
R9101
R9102
R9103
R9104
R9105
R9106
R9107
R9108
R9109
R9110
R9111
R9112
R9113
R9114
VRS-CY1JF000J
VRS-CY1JF103J
VRS-CY1JF103J
VRS-CY1JF111F
VRS-CY1JF111F
VRS-CY1JF103J
VRS-CY1JF560F
VRS-CY1JF560F
VRS-CY1JF302F
VRS-CY1JF683F
VRS-TV1JD240J
VRS-CY1JF103J
VRS-CY1JF333J
VRS-CY1JF333J
VRS-CY1JF471J
VRS-CY1JF182J
VRS-CY1JF472J
VRS-CY1JF471J
VRS-CY1JF473J
VRS-CY1JF103J
VRS-CY1JF102J
VRS-CY1JF102J
VRS-CY1JF473J
VRS-CY1JF101J
VRS-CY1JF101J
VRS-CY1JF101J
VRS-CY1JF101J
VRS-CY1JF101J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
Description
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
10
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
220
3.3
0.1
0.1
0.1
0.1
0.1
Code
25V
25V
25V
25V
25V
25V
25V
25V
25V
25V
25V
16V
25V
25V
50V
25V
25V
25V
25V
25V
25V
25V
25V
25V
25V
25V
25V
25V
25V
25V
25V
25V
25V
25V
25V
25V
25V
25V
25V
4.0V
50V
25V
25V
25V
25V
25V
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Electrolytic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Electrolytic
Electrolytic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AB
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AB
AB
AA
AA
AA
AA
AA
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
RESISTORS
AA
104
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
0
10k
10k
110
110
10k
56
56
3.0k
68k
24
10k
33k
33k
470
1.8k
4.7k
470
47k
10k
1.0k
1.0k
47k
100
100
100
100
100
PG-M20X
Ref. No.
★
Part No.
Description
Code
DUNTKB066DE01
INPUT UNIT
R9115
R9116
R9118
R9119
R9120
R9121
R9131
R9132
R9135
R9201
R9202
R9203
R9204
R9205
R9206
R9207
R9301
R9302
R9303
R9304
R9305
R9306
R9307
R9308
R9309
R9310
R9401
R9402
R9502
R9503
R9506
R9507
R9508
R9509
R9510
R9511
R9512
R9515
R9517
R9518
R9519
R9522
R9524
R9527
R9528
R9529
R9530
R9532
R9535
R9538
R9539
R9541
R9542
R9543
R9546
R9547
R9548
R9549
R9550
R9551
R9552
R9553
R9554
R9555
R9556
R9557
R9558
R9559
R9560
R9561
R9562
R9563
VRS-CY1JF101J
VRS-CY1JF000J
VRS-CY1JF101J
VRS-CY1JF101J
VRS-CY1JF101J
VRS-CY1JF101J
VRS-CY1JF184J
VRN-CY1JF472D
VRS-CY1JF103J
VRK-CD1JJ390F
VRK-CD1JJ390F
VRK-CD1JJ390F
VRS-CY1JF390F
VRS-CY1JF390F
VRS-CY1JF390F
VRS-CY1JF390F
VRK-CC1JJ220J
VRK-CC1JJ220J
VRS-CB1JF220J
VRK-CC1JJ220J
VRK-CC1JJ220J
VRK-CC1JJ220J
VRK-CC1JJ220J
VRK-CC1JJ220J
VRK-CC1JJ220J
VRS-CA1JF220J
VRS-CA1JF273J
VRS-CB1JF273J
VRS-CY1JF222J
VRS-CA1JF103J
VRS-CY1JF240F
VRS-CY1JF103J
VRS-CY1JF103J
VRS-CY1JF102J
VRS-CY1JF240F
VRS-CY1JF102J
VRS-CY1JF222J
VRS-TV1JD270J
VRS-CY1JF103J
VRS-CY1JF240F
VRS-CY1JF102J
VRS-CY1JF103J
VRS-CY1JF240J
VRS-CY1JF104F
VRS-CY1JF273J
VRS-TV1JD240J
VRS-TV1JD330J
VRS-CY1JF103J
VRS-CY1JF203F
VRS-TV1JD1R0J
VRN-CY1JF472D
VRS-CY1JF202F
VRS-CY1JF111F
VRS-CY1JF240J
VRS-TV1JD100J
VRS-CY1JF432F
VRN-CY1JF472D
VRS-TV1JD1R0J
VRN-CY1JF203D
VRS-CY1JF222F
VRS-TV1JD240J
VRS-TV1JD240J
VRS-CY1JF102J
VRS-TV1JD1R0J
VRS-CY1JF100J
VRS-CY1JF820F
VRS-CY1JF331F
VRS-CY1JF000J
VRS-CY1JF102J
VRS-CY1JF562J
VRS-CY1JF330F
VRS-CY1JF561F
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
100 1/16W
0
1/16W
100 1/16W
100 1/16W
100 1/16W
100 1/16W
180k 1/16W
4.7k 1/16W
10k 1/16W
39 1/16W
39 1/16W
39 1/16W
39 1/16W
39 1/16W
39 1/16W
39 1/16W
22 1/16W
22 1/16W
22 1/16W
22 1/16W
22 1/16W
22 1/16W
22 1/16W
22 1/16W
22 1/16W
22 1/16W
27k 1/16W
27k 1/16W
2.2k 1/16W
10k 1/16W
24 1/16W
10k 1/16W
10k 1/16W
1.0k 1/16W
24 1/16W
1.0k 1/16W
2.2k 1/16W
27 1/16W
10k 1/16W
24 1/16W
1.0k 1/16W
10k 1/16W
24 1/16W
100k 1/16W
27k 1/16W
24 1/16W
33 1/16W
10k 1/16W
20k 1/16W
1.0 1/16W
4.7k 1/16W
2.0k 1/16W
110 1/16W
24 1/16W
10 1/16W
4.3k 1/16W
4.7k 1/16W
1.0 1/16W
20k 1/16W
2.2k 1/16W
24 1/16W
24 1/16W
1.0k 1/16W
1.0 1/16W
10 1/16W
82 1/16W
330 1/16W
0
1/16W
1.0k 1/16W
5.6k 1/16W
33 1/16W
560 1/16W
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Film
Metal Oxide
Metal Compo
Metal Compo
Metal Compo
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Compo
Metal Compo
Metal Oxide
Metal Compo
Metal Compo
Metal Compo
Metal Compo
Metal Compo
Metal Compo
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Film
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Film
Metal Oxide
Metal Film
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
AA
AA
AA
AA
AA
AA
AA
AA
AA
Ref. No.
Part No.
★
R9564
R9565
R9566
R9567
R9569
R9574
R9575
R9591
R9592
VRS-CY1JF562J
VRS-CY1JF103J
VRS-CY1JF821F
VRS-CY1JF121F
VRS-CY1JF102J
VRS-CY1JF222J
VRS-CY1JF222J
VRS-TW2ED000J
VRS-CY1JF103J
J
J
J
J
J
J
J
J
J
Description
5.6k
10k
820
120
1.0k
2.2k
2.2k
0
10k
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/4W
1/16W
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Code
AA
AA
AA
AA
AA
AA
AA
AB
AA
SWITCH
S9001 QSW-SA004WJZZ
J Slide Switch
MISCELLANEOUS PARTS
FB9001 RBLN-0061TAZZ
FB9002 RBLN-0061TAZZ
FB9003 RBLN-0061TAZZ
FB9004 RBLN-0210TAZZ
FB9005 RBLN-0210TAZZ
FB9006 RBLN-0061TAZZ
FB9502 RBLN-0210TAZZ
FB9507 RBLN-0210TAZZ
P9002 QPLGN0474TAZZ
P9003 QPLGN0363TAZZ
SC9001 QSOCN8003WJZZ
SC9002 QSOCN3078TAZZ
AC
AA
AA
AC
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AB
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
105
J
J
J
J
J
J
J
J
J
J
J
J
Ferrite Bead
Ferrite Bead
Ferrite Bead
Ferrite Bead
Ferrite Bead
Ferrite Bead
Ferrite Bead
Ferrite Bead
Plug, 4-pin
Plug, 3-pin
Socet, 80-pin
Socet ,30-pin
AD
AD
AD
AB
AB
AD
AB
AB
AD
AC
AE
PG-M20X
Ref. No.
★
Part No.
Description
Code
C3106
C3107
C3109
C3110
C3111
C3112
C3113
C3114
C3115
C3116
C3117
C3118
C3119
C3120
C3121
C3122
C3201
C3202
C3204
C3205
C3301
C3302
C3303
C3304
C3305
C3306
C3307
C3308
C3309
C3310
C3503
C3504
C3507
C3510
C3511
C3513
C3547
C3551
C3701
C3702
C3703
C3706
C3707
C3708
C3710
C3711
C3712
C3715
C3718
C3722
C3725
C3726
C3728
C3733
C3734
C3741
C3742
C3851
C3852
C3853
C3854
C3855
C3856
C3857
C3858
C3862
C3863
C3864
C3865
C3901
C3903
C3904
C3905
C3907
C3909
C3910
DUNTKB066DE01
INPUT UNIT
INTEGRATED CIRCUITS
IC3002
IC3101
IC3102
IC3103
IC3201
IC3301
IC3502
IC3702
IC3704
IC3705
IC3708
IC3851
IC3901
IC3902
IC3903
VHiM62392FP-1
VHiA8902CLB-1
VHiPQ20WZ11-1
VHiSNT1G14C-1
RH-iXA178WJZZ
VHiDA7056AT-1
VHiNJM2244M-1
VHiPQ12DZ1U-1
VHiPQ20WZ11-1
VHiPQ05DZ1U-1
VHiBD4744G+-1
VHiSM5300AV-1
VHiTL712CPW-1
VHiLMH6643A-1
VHiTL712CPW-1
Q3002
Q3003
Q3004
Q3101
Q3201
Q3205
Q3206
Q3502
Q3507
Q3512
Q3513
Q3851
Q3852
Q3853
Q3854
Q3855
Q3904
VSHN1K03FU+-1
VSHN1K03FU+-1
VS2SB1132Q/-1
VSDTC114EE/-1
VSBSS84++++-1
VSHN1K03FU+-1
VSRN1905///-1
VS2SC3928AR-1
VS2SC3928AR-1
VS2SA1530AR-1
VS2SC3928AR-1
VS2SC2735//-1
VS2SC2735//-1
VS2SC2735//-1
VSHN2C01FU/-1
VSHN2C01FU/-1
VS2SC2412KQ-1
D3101
D3102
D3103
D3104
D3105
D3201
D3202
D3203
D3501
D3502
D3503
D3702
D3704
TH3001
VHDBAT54SWT-1
VHDBAT54SWT-1
VHDBAT54SWT-1
VHDDAN222//-1
VHDBAT54SWT-1
VHDMA3120WA-1
VHDMA3120WA-1
VHDMA3120WA-1
RH-EX0227CEZZ
RH-EX0227CEZZ
RH-EX0227CEZZ
VHDDAN222//-1
VHDDAN222//-1
RH-HXA001WJZZ
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
M62392FP
A8902CLB
PQ20WZ1U
SNT1G14C
IC
TDA7056AT/N2
NJM2244M
PQ12DZ1U
PQ20WZ1U
PQ05DZ1U
BD4744G-TR
SM5300AV
T1712CPWR
LMH6643A
T1712CPWR
AM
AG
AG
AG
AL
AL
TRANSISTORS
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
HN1K03FU
HN1K03FU
2SB1132Q
DTC114EE
BSS84
HN1K03FU
RN1905
2SC3928AR
2SC3928AR
2SA1530AR
2SC3928AR
2SC2735
2SC2735
2SC2735
HN2C01FU
HN2C01FU
2SC2412KQ
AC
AB
AB
AB
AB
AB
AB
AB
AB
AC
AC
AA
DIODES AND THERMISTER
J
J
J
J
J
J
J
J
J
J
J
J
J
J
Diode
Diode
Diode
Diode
Diode
Diode
Diode
Diode
Zener Diode
Zener Diode
Zener Diode
Diode
Diode
Thermister
AA
AK
AK
AK
AB
AB
AB
AA
AA
AD
PACKAGED CIRCUIT AND FILTERS
X3201
FL3501
FL3502
FL3503
FL3506
RFiLA0042CEZZ
RFiLN0003TAZZ
RFiLN0003TAZZ
RFiLN0003TAZZ
RCiLF0306CEZZ
C3001
C3002
C3003
C3004
C3005
C3006
C3101
C3102
C3103
C3104
C3105
VCKYCY1EF104Z
VCKYCY1EF104Z
VCKYCY1EF104Z
VCKYCY1EF104Z
VCKYCY1EF104Z
VCKYCY1EF104Z
VCKYCY1HB102K
VCKYCY1HB332K
VCKYCY1HB332K
VCKYCY1HB102K
VCKYCY1HB222K
J
J
J
J
J
Filter, 454kHz
Filter
Filter
Filter
Filter
AD
AD
AD
AD
AH
CAPACITORS
J
J
J
J
J
J
J
J
J
J
J
0.1
0.1
0.1
0.1
0.1
0.1
1000p
3300p
3300p
1000p
2200p
25V
25V
25V
25V
25V
25V
50V
50V
50V
50V
50V
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ref. No.
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
106
Part No.
VCEASM1HW105M
VCKYCY1HB102K
VCKYCY1EF104Z
VCKYCY1HF224Z
VCKYCY1EF104Z
VCKYCY1HB562K
VCKYCY1AB154K
VCEASM1EW106M
VCKYCY1EF104Z
VCEASM1CW476M
VCKYCY1EF104Z
VCKYCY1EF104Z
VCEASM1CW106M
VCKYCY1EF104Z
VCKYCY1EF104Z
VCKYCY1EF104Z
VCEASM1CW106M
VCKYCY1EF104Z
VCCCCY1HH150J
VCCCCY1HH150J
VCCCCY1HH101J
VCCCCY1HH101J
VCE9PF1CW106M
VCE9PF1CW106M
VCEASM1CW106M
VCCCCY1HH471J
VCEASM1CW107M
VCKYCY1EF104Z
VCEASM1CW106M
VCKYCY1EF104Z
VCEASM1CW106M
VCEASM1CW106M
VCEASM1CW106M
VCEASM1CW106M
VCEASM1CW106M
VCEASM1CW476M
VCKYCY1EF104Z
VCKYCY1EF104Z
VCKYCY1EF104Z
VCKYCY1EF104Z
VCEASM1CW106M
VCKYCY1EF104Z
VCKYCY1EF104Z
VCEASM1EW476M
VCEASM1EW106M
VCKYCY1EF104Z
VCEASM1CW226M
VCKYCY1EF104Z
VCEASM1CW106M
VCEASM0JW226M
VCKYCY1EF104Z
VCKYCY1EF104Z
VCKYCY1EF104Z
VCKYCY1EF104Z
VCKYCY1EF104Z
VCKYCY1EF104Z
VCKYCY1EF104Z
VCKYCY1EF104Z
VCEASM1HW105M
VCEASM1HW105M
VCEASM1HW105M
VCKYCY1EF104Z
VCKYCY1EF104Z
VCKYCY1EF104Z
VCKYCY1EF104Z
VCEASM1CW106M
VCEASM1CW106M
VCEASM1CW106M
VCEASM1CW106M
VCKYCY1EF104Z
VCKYCY1EF104Z
VCKYCY1EF104Z
VCKYCY1EF104Z
VCE9PF1HW474M
VCCCCY1HH101J
VCKYCY1EF104Z
★
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
Description
1.0
1000p
0.1
0.22
0.1
5600p
0.15
10
0.1
47
0.1
0.1
10
0.1
0.1
0.1
10
0.1
15p
15p
100p
100p
10
10
10
470p
100
0.1
10
0.1
10
10
10
10
10
47
0.1
0.1
0.1
0.1
10
0.1
0.1
47
10
0.1
22
0.1
10
22
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
1.0
1.0
1.0
0.1
0.1
0.1
0.1
10
10
10
10
0.1
0.1
0.1
0.1
0.47
100p
0.1
50V
50V
25V
50V
25V
50V
10V
25V
25V
16V
25V
25V
16V
25V
25V
25V
16V
25V
50V
50V
50V
50V
16V
16V
16V
50V
16V
25V
16V
25V
16V
16V
16V
16V
16V
16V
25V
25V
25V
25V
16V
25V
25V
25V
25V
25V
16V
25V
16V
6.3V
25V
25V
25V
25V
25V
25V
25V
25V
50V
50V
50V
25V
25V
25V
25V
16V
16V
16V
16V
25V
25V
25V
25V
50V
50V
25V
Electrolytic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Electrolytic
Ceramic
Electrolytic
Ceramic
Ceramic
Electrolytic
Ceramic
Ceramic
Ceramic
Electrolytic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Elect.(N.P)
Elect.(N.P)
Electrolytic
Ceramic
Electrolytic
Ceramic
Electrolytic
Ceramic
Electrolytic
Electrolytic
Electrolytic
Electrolytic
Electrolytic
Electrolytic
Ceramic
Ceramic
Ceramic
Ceramic
Electrolytic
Ceramic
Ceramic
Electrolytic
Electrolytic
Ceramic
Electrolytic
Ceramic
Electrolytic
Electrolytic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Electrolytic
Electrolytic
Electrolytic
Ceramic
Ceramic
Ceramic
Ceramic
Electrolytic
Electrolytic
Electrolytic
Electrolytic
Ceramic
Ceramic
Ceramic
Ceramic
Elect.(N.P)
Ceramic
Ceramic
Code
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AC
AC
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AD
AA
AA
PG-M20X
Ref. No.
★
Part No.
Description
Code
DUNTKB066DE01
INPUT UNIT (Continued)
C3911 VCKYCY1HB222K
J 2200p 50V
Ceramic
AA
RESISTORS
R3003
R3004
R3006
R3009
R3010
R3012
R3014
R3023
R3024
R3026
R3027
R3101
R3102
R3103
R3104
R3105
R3106
R3107
R3108
R3109
R3111
R3113
R3114
R3115
R3116
R3118
R3119
R3120
R3121
R3122
R3123
R3124
R3125
R3126
R3201
R3206
R3207
R3209
R3212
R3213
R3216
R3222
R3225
R3226
R3227
R3229
R3230
R3231
R3232
R3233
R3234
R3235
R3302
R3303
R3304
R3305
R3306
R3307
R3308
R3309
R3310
R3311
R3312
R3313
R3501
R3504
R3505
R3506
R3515
VRS-CY1JF184J
VRS-CY1JF472J
VRS-CA1JF332J
VRS-CY1JF000J
VRS-CY1JF000J
VRS-CY1JF332J
VRS-CY1JF000J
VRS-CY1JF221J
VRS-CY1JF102J
VRS-CY1JF000J
VRS-CY1JF000J
VRS-TW2ED151J
VRS-CY1JF102J
VRS-CY1JF102J
VRS-TW2ED151J
VRS-CY1JF102J
VRS-CY1JF000J
VRS-CY1JF102J
VRS-CY1JF000J
VRS-TW2ED151J
VRS-CY1JF000J
VRS-CY1JF103J
VRS-CY1JF305J
VRS-TX2HF2R2J
VRS-CY1JF390F
VRS-CY1JF562F
VRS-CY1JF101J
VRS-CY1JF222F
VRS-CY1JF472F
VRS-CY1JF682J
VRS-CY1JF101J
VRS-CY1JF472J
VRS-CE3AF5R6J
VRS-CE3AF5R6J
RBLN-0060TAZZ
VRS-CY1JF104J
VRS-CY1JF752F
VRS-CY1JF103J
VRS-CY1JF154J
VRS-CY1JF224J
VRS-CY1JF103J
VRS-CY1JF000J
VRS-CY1JF103J
VRS-CY1JF000J
VRS-CY1JF000J
VRS-CY1JF000J
VRS-CY1JF103J
VRS-CY1JF103J
VRS-CY1JF000J
VRS-CY1JF103J
VRS-CY1JF000J
VRS-CY1JF103J
VRS-CY1JF223J
VRS-CY1JF223J
VRS-CY1JF224J
VRS-CY1JF224J
VRS-CY1JF473J
VRS-CA1JF272J
VRS-CY1JF102J
VRS-CY1JF103J
VRS-CY1JF102J
VRS-CY1JF393J
VRS-CY1JF823J
VRS-TX2HF8R2J
VRS-TV1JD000J
VRS-TW2ED750J
VRS-TW2ED750J
VRS-TW2ED750J
VRS-CY1JF332J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
180k 1/16W
4.7k 1/16W
3.3k 1/16W
0
1/16W
0
1/16W
3.3k 1/16W
0
1/16W
220 1/16W
1.0k 1/16W
0
1/16W
0
1/16W
150 1/4W
1.0k 1/16W
1.0k 1/16W
150 1/4W
1.0k 1/16W
0
1/16W
1.0k 1/16W
0
1/16W
150 1/4W
0
1/16W
10k 1/16W
3.0M 1/16W
2.2 1/2W
39 1/16W
5.6k 1/16W
100 1/16W
2.2k 1/16W
4.7k 1/16W
6.8k 1/16W
100 1/16W
4.7k 1/16W
5.6 1W
5.6 1W
100k 1/16W
7.5k 1/16W
10k 1/16W
150k 1/16W
220k 1/16W
10k 1/16W
0
1/16W
10k 1/16W
0
1/16W
0
1/16W
0
1/16W
10k 1/16W
10k 1/16W
0
1/16W
10k 1/16W
0
1/16W
10k 1/16W
22k 1/16W
22k 1/16W
220k 1/16W
220k 1/16W
47k 1/16W
2.7k 1/16W
1.0k 1/16W
10k 1/16W
1.0k 1/16W
39k 1/16W
82k 1/16W
8.2 1/2W
0
1/16W
75 1/4W
75 1/4W
75 1/4W
3.3k 1/16W
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Ferrite Bead
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AB
AA
AA
AA
AA
AA
AA
AA
AB
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
Ref. No.
Part No.
★
R3516
R3522
R3526
R3528
R3531
R3537
R3547
R3551
R3552
R3553
R3561
R3562
R3563
R3564
R3705
R3707
R3708
R3709
R3711
R3715
R3716
R3717
R3718
R3851
R3852
R3856
R3857
R3858
R3863
R3864
R3865
R3866
R3867
R3868
R3870
R3871
R3872
R3873
R3877
R3878
R3879
R3904
R3905
R3907
R3908
R3909
R3910
R3914
R3915
R3916
R3917
R3918
VRS-CY1JF562J
VRS-CY1JF122J
VRS-CY1JF332J
VRS-CY1JF562J
VRS-CY1JF122J
VRS-TV1JD000J
VRS-TV1JD000J
VRS-CY1JF105J
VRS-CY1JF105J
VRS-TV1JD000J
VRS-CY1JF102J
VRS-CY1JF391J
VRS-CY1JF392J
VRS-CY1JF471J
VRS-CY1JF101J
VRS-CY1JF101J
VRS-CY1JF223F
VRS-CY1JF392F
VRS-CY1JF101J
VRS-CE3AF3R3J
VRS-CY1JF000J
VRS-CE3AF2R2J
VRS-CY1JF223F
VRS-CY1JF000J
VRS-CY1JF000J
VRS-CY1JF000J
VRS-CY1JF000J
VRS-CY1JF821J
VRS-CY1JF103J
VRS-TV1JD750J
VRS-CY1JF103J
VRS-TV1JD750J
VRS-CY1JF103J
VRS-TV1JD750J
VRS-CY1JF101J
VRS-CY1JF101J
VRS-CB1JF223J
VRS-CB1JF223J
VRS-CY1JF102J
VRS-CY1JF102J
VRS-CY1JF102J
VRS-CY1JF112F
VRS-CY1JF151F
VRS-CY1JF102J
VRS-CY1JF272F
VRS-CY1JF102J
VRS-CY1JF103J
VRS-CY1JF821J
VRS-CY1JF333J
VRS-CY1JF821J
VRS-CY1JF470J
VRS-CY1JF123J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
Description
5.6k 1/16W
1.2k 1/16W
3.3k 1/16W
5.6k 1/16W
1.2k 1/16W
0
1/16W
0
1/16W
1.0M 1/16W
1.0M 1/16W
0
1/16W
1.0k 1/16W
390 1/16W
3.9k 1/16W
470 1/16W
100 1/16W
100 1/16W
22k 1/16W
3.9k 1/16W
100 1/16W
3.3 1W
0
1/16W
2.2 1W
22k 1/16W
0
1/16W
0
1/16W
0
1/16W
0
1/16W
820 1/16W
10k 1/16W
75 1/16W
10k 1/16W
75 1/16W
10k 1/16W
75 1/16W
100 1/16W
100 1/16W
22k 1/16W
22k 1/16W
1.0k 1/16W
1.0k 1/16W
1.0k 1/16W
1.1k 1/16W
150 1/16W
1.0k 1/16W
2.7k 1/16W
1.0k 1/16W
10k 1/16W
820 1/16W
33k 1/16W
820 1/16W
47 1/16W
12k 1/16W
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Code
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
MISCELLANEOUS PARTS
FB3101 RBLN-0210TAZZ
FB3102 RBLN-0062CEZZ
FB3103 RBLN-0059CEZZ
FB3201 RBLN-0060TAZZ
FB3202 RBLN-0060TAZZ
FB3203 RBLN-0060TAZZ
FB3301 RBLN-0064TAZZ
FB3302 RBLN-0058CEZZ
FB3303 RBLN-0058CEZZ
FB3304 RBLN-0064TAZZ
J3201 QSOCNA005WJZZ
J3301 QJAKJ0066CEZZ
J3501 QJAKEA002WJZZ
J3502 QSOCD0426CEZZ
P3002 QSOCN3278TAZZ
P3003 QSOCN3078TAZZ
P3101 QPLGN0198FJZZ
SC3001 QCNCW8002WJZZ
SC3101 QSOCN0401WJZZ
SC3701 QSOCZ1338CEZZ
LANGF9661CEFW
XBBSD20P03000
107
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
Ferrite Bead
Ferrite Bead
Ferrite Bead
Ferrite Bead
Ferrite Bead
Ferrite Bead
Ferrite Bead
Ferrite Bead
Ferrite Bead
Ferrite Bead
Jack, 4-Pin
Jack , PC Audio IN
Jack, Video IN
Din Jack Socket
Plug, 32-pin
Plug, 30-pin
Plug, 3-pin
Socket, 80-pin
Socket, 4-pin
Socket, 13-pin
Angle
Screw
AB
AC
AB
AB
AB
AB
AC
AB
AB
AC
AE
AE
AD
AE
AE
AD
AD
AA
PG-M20X
Ref. No.
★
Part No.
Description
Code
DUNTKB067DE01
KEY UNIT
INTEGRATED CIRCUITS
IC2001
IC2002
IC2004
IC2005
IC2010
IC2011
IC2101
IC2102
IC2103
IC2104
RH-iXA128WJZZ
VHiBD4729G+-1
VHiSNAT541P-1
VHiSNHC32T/-1
VHiPQ1R33//-1
VHiPQ1R50//-1
VHiBA00ASFP-1
VHiBA00ASFP-1
VHiBA00ASFP-1
VHiBA00ASFP-1
J
J
J
J
J
J
J
J
J
J
Q2001
Q2002
Q2003
Q2004
Q2101
Q2201
Q2202
Q2203
Q2204
Q2205
VSDTC114EE/-1
VSDTC114EE/-1
VS2SB1132Q/-1
VS2SA1530AR-1
VSDTC114EE/-1
VSDTC144EUA-1
VSDTC144EUA-1
VSDTC144EUA-1
VSDTC144EUA-1
VSDTC144EUA-1
D2001
D2002
D2003
D2101
D2102
D2103
D2104
D2105
D2106
D2201
D2202
D2203
VHDDAN222//-1
VHDDAN222//-1
VHDF01J2E//-1
VHDDAN202K/-1
VHDDAN202K/-1
VHDDAN202K/-1
VHDDAN202K/-1
VHDDAN202K/-1
VHDDAN202K/-1
RH-PX0210TAZZ
RH-PX0210TAZZ
RH-PX0210TAZZ
Ic
BD4729G-TR
SNAT541P
SN74HC32PW
PQ1R33
PQ1R50
BA00ASFP-E2
BA00ASFP-E2
BA00ASFP-E2
BA00ASFP-E2
AG
AE
AF
AG
AG
AG
AG
TRANSISTORS
J
J
J
J
J
J
J
J
J
J
DTC114EE
DTC114EE
2SB1132Q
2SA1530AR
DTC114EE
DTC144EUA
DTC144EUA
DTC144EUA
DTC144EUA
DTC144EUA
AB
AB
AC
AB
AB
AB
AB
AB
AB
AB
Diode
Diode
Diode
Diode
Diode
Diode
Diode
Diode
Diode
Diode
Diode
Diode
AA
AA
AC
AB
AB
AB
AB
AB
AB
PACKAGED CIRCUIT
X2001 RCRSB0286CEZZ
J Crystal
AH
CAPACITORS
C2001
C2002
C2003
C2004
C2005
C2006
C2007
C2010
C2011
C2012
C2013
C2014
C2015
C2016
C2017
C2019
C2020
C2021
C2022
C2023
C2024
C2025
C2026
C2027
C2028
C2029
C2030
C2101
C2103
VCKYCY1EF104Z
VCKYCY1EF104Z
VCKYCY1EF104Z
VCKYCY1EF104Z
VCKYCY1AF105Z
VCKYCY1AF105Z
VCKYCY1EF104Z
VCKYCY1EF104Z
VCKYCY1EF104Z
VCKYCY1EF104Z
VCKYCY1EF104Z
VCKYCY1EF104Z
VCKYCY1EF104Z
VCKYCY1EF104Z
VCEASM0JW476M
VCKYCY1EF104Z
VCCCCY1HH220J
VCCCCY1HH220J
VCKYCY1EF104Z
VCKYCY1EF104Z
VCKYCY1EF104Z
VCEASM1CW106M
VCKYCY1EF104Z
VCKYCY1EF104Z
VCKYCY1EF104Z
VCEASM1CW106M
VCKYCY1EF104Z
VCKYCY1EF104Z
VCEASM1EW336M
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
0.1
0.1
0.1
0.1
1.0
1.0
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
47
0.1
22p
22p
0.1
0.1
0.1
10
0.1
0.1
0.1
10
0.1
0.1
33
25V
25V
25V
25V
10V
10V
25V
25V
25V
25V
25V
25V
25V
25V
6.3V
25V
50V
50V
25V
25V
25V
16V
25V
25V
25V
16V
25V
25V
25V
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Electrolytic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Electrolytic
Ceramic
Ceramic
Ceramic
Electrolytic
Ceramic
Ceramic
Electrolytic
★
Part No.
C2104
C2105
C2106
C2108
C2109
C2110
C2111
C2112
C2113
C2114
C2115
C2116
C2117
C2118
C2119
C2120
C2201
C2202
C2203
VCKYCY1EF104Z
VCKYCY1EF104Z
VCEASM1CW107M
VCEASM1EW336M
VCEASM1EW336M
VCKYCY1EF104Z
VCKYCY1EF104Z
VCKYCY1EF104Z
VCKYCY1EF104Z
VCKYCY1EF104Z
VCEASM1CW107M
VCEASM1CW107M
VCEASM1EW336M
VCKYCY1EF104Z
VCEASM1CW107M
VCKYCY1EF104Z
VCKYCY1EF104Z
VCEASM1CW226M
VCKYCY1EF104Z
R2001
R2004
R2005
R2006
R2007
R2008
R2009
R2010
R2011
R2012
R2013
R2014
R2016
R2018
R2019
R2020
R2021
R2022
R2023
R2025
R2027
R2029
R2030
R2032
R2033
R2101
R2103
R2104
R2105
R2106
R2108
R2109
R2110
R2111
R2112
R2113
R2114
R2115
R2116
R2117
R2118
R2120
R2121
R2122
R2124
R2125
R2126
R2127
R2128
R2129
R2130
R2132
R2133
R2134
R2201
VRS-CY1JF000J
VRS-CY1JF000J
VRS-CY1JF471J
VRS-CY1JF103J
VRS-CY1JF100J
VRS-CY1JF103J
VRS-CY1JF100J
VRS-CY1JF102J
VRS-CY1JF102J
VRS-CY1JF104J
VRS-CY1JF222J
VRS-CY1JF101J
VRS-CY1JF101J
VRS-CY1JF104J
VRS-CY1JF101J
VRS-CY1JF104J
VRS-CY1JF102J
VRS-CY1JF102J
VRS-CY1JF102J
VRS-TV1JD471J
VRS-CY1JF000J
VRS-CY1JF103J
VRS-CY1JF103J
VRS-CY1JF103J
VRS-CY1JF103J
VRS-CY1JF101J
VRS-TW2ED2R2J
VRS-CY1JF472F
VRS-CY1JF102F
VRS-CY1JF822F
VRS-CY1JF682J
VRS-CY1JF101J
VRS-CB1JF472J
VRS-TW2ED2R2J
VRS-TW2ED2R2J
VRS-CY1JF101J
VRS-CY1JF332F
VRS-CY1JF101J
VRS-CY1JF472F
VRS-CY1JF102F
VRS-CY1JF683F
VRS-CY1JF102F
VRS-CY1JF103F
VRS-CY1JF822F
VRS-CY1JF000J
VRS-CY1JF000J
VRS-TW2ED2R2J
VRS-CY1JF332F
VRS-CY1JF102F
VRS-CY1JF473F
VRS-CY1JF103F
VRS-CY1JF101J
VRS-CY1JF000J
VRS-CY1JF000J
VRS-CY1JF102J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
Description
0.1
0.1
100
33
33
0.1
0.1
0.1
0.1
0.1
100
100
33
0.1
100
0.1
0.1
22
0.1
25V
25V
16V
25V
25V
25V
25V
25V
25V
25V
16V
16V
25V
25V
16V
25V
25V
16V
25V
Code
Ceramic
Ceramic
Electrolytic
Electrolytic
Electrolytic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Electrolytic
Electrolytic
Electrolytic
Ceramic
Electrolytic
Ceramic
Ceramic
Electrolytic
Ceramic
AA
AA
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AB
AA
AA
AA
AA
AA
AC
AB
AB
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AB
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
RESISTORS
DIODES
J
J
J
J
J
J
J
J
J
J
J
J
Ref. No.
AA
AA
AA
AA
AC
AC
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
108
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
0
1/16W
0
1/16W
470 1/16W
10k 1/16W
10 1/16W
10k 1/16W
10 1/16W
1.0k 1/16W
1.0k 1/16W
100k 1/16W
2.2k 1/16W
100 1/16W
100 1/16W
100k 1/16W
100 1/16W
100k 1/16W
1.0k 1/16W
1.0k 1/16W
1.0k 1/16W
470 1/16W
0
1/16W
10k 1/16W
10k 1/16W
10k 1/16W
10k 1/16W
100 1/16W
2.2 1/4W
4.7k 1/16W
1.0k 1/16W
8.2k 1/16W
6.8k 1/16W
100 1/16W
4.7k 1/16W
2.2 1/4W
2.2 1/4W
100 1/16W
3.3k 1/16W
100 1/16W
4.7k 1/16W
1.0k 1/16W
68k 1/16W
1.0k 1/16W
10k 1/16W
8.2k 1/16W
0
1/16W
0
1/16W
2.2 1/4W
3.3k 1/16W
1.0k 1/16W
47k 1/16W
10k 1/16W
100 1/16W
0
1/16W
0
1/16W
1.0k 1/16W
PG-M20X
Ref. No.
★
Part No.
Description
Code
Ref. No.
Part No.
★
Description
DUNTKB067DE01
RDENCA004WJZZ
KEY UNIT (Continued)
POWER UNIT
R2202
R2203
R2204
R2205
R2206
R2207
R2208
R2209
R2210
R2211
R2212
R2213
R2214
R2215
R2216
VRS-CB1JF102J
VRS-CY1JF103J
VRS-CB1JF103J
VRS-CY1JF562J
VRS-CY1JF562J
VRS-CY1JF562J
VRS-CY1JF562J
VRS-TW2ED221J
VRS-TW2ED681J
VRS-TW2ED221J
VRS-TW2ED681J
VRS-TW2ED681J
VRS-CY1JF682J
VRS-CY1JF682J
VRS-CY1JF682J
SW2001
SW2002
SW2201
SW2202
SW2203
SW2204
SW2205
SW2206
SW2207
SW2208
SW2209
SW2210
SW2211
SW2212
QSW-KA001WJZZ
QSW-S0203TAZZ
QSW-KA001WJZZ
QSW-KA001WJZZ
QSW-KA001WJZZ
QSW-KA001WJZZ
QSW-KA001WJZZ
QSW-KA001WJZZ
QSW-KA001WJZZ
QSW-KA001WJZZ
QSW-KA001WJZZ
QSW-KA001WJZZ
QSW-KA001WJZZ
QSW-KA001WJZZ
FB2003
FB2004
FB2101
FB2102
FB2103
FB2104
FB2105
FB2106
FB2107
FB2108
FB2109
FB2110
P2001
P2002
P2003
P2101
P2102
P2103
P2104
RBLN-0064TAZZ
RBLN-0064TAZZ
RBLN-0064TAZZ
RBLN-0059CEZZ
RBLN-0064TAZZ
RBLN-0059CEZZ
RBLN-0064TAZZ
RBLN-0059CEZZ
RBLN-0064TAZZ
RBLN-0064TAZZ
RBLN-0064TAZZ
RBLN-0059CEZZ
QSOCN3271TAZZ
QPLGN0264TAZZ
QPLGN0664TAZZ
QPLGN0464TAZZ
QPLGN0364TAZZ
QPLGN0463TAZZ
QPLGN0363TAZZ
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
1.0k
10k
10k
5.6k
5.6k
5.6k
5.6k
220
680
220
680
680
6.8k
6.8k
6.8k
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/4W
1/4W
1/4W
1/4W
1/4W
1/16W
1/16W
1/16W
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
INTEGRATED CIRCUITS
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
IC7101 0H1Q3A0010
IC7401 0H1R3A0010
TRANSISTORS
SWITCHES
J
J
J
J
J
J
J
J
J
J
J
J
J
J
Switch
Switch
Switch
Switch Lens
Switch Menu
Switch Auto Sync
Switch AV Mute
Switch Cursor Up
Switch Cursor Down
Switch Cursor Left
Switch Cursor Right
Switch Undo
Switch Input
Switch Enter
AD
Ferrite Bead
Ferrite Bead
Ferrite Bead
Ferrite Bead
Ferrite Bead
Ferrite Bead
Ferrite Bead
Ferrite Bead
Ferrite Bead
Ferrite Bead
Ferrite Bead
Ferrite Bead
Plug, 32-pin(KY)
Plug, 2-pin(SP)
Plug, 6-pin(EB)
Plug, 4-pin(F1)
Plug, 3-pin(F2)
Plug, 4-pin(F3)
Plug, 3-pin(F5)
Q7301
Q7302
Q7320
Q7322
Q7330
Q7340
Q7402
Q7403
Q7405
Q7422
Q7423
Q7425
Q7461
Q7462
0T601B0010
0T395A0010
0T601B0010
0T395A0010
0T196A0010
0T395A0010
0T395A0010
0T193A0010
0T593A0010
0T395A0010
0T193A0010
0T593A0010
0T193A0010
0T395A0010
D711
D712
D7101
D7102
D7103
D7104
D7110
D7304
D7306
D7307
D7308
D7309
D7322
D7330
D7340
D7401
D7402
D7421
D7422
0D292A0020
0D292A0020
0D224B0060
0D2Q0A0100
0D2Q0A0100
0D2Q0A0100
0D461A1900
0D295A0080
0D295A0080
0D295A0080
0D491A0300
0D491A0300
0D295A0080
0D491A0250
0D295A0080
0D2Q0A0030
0D2Q0A0030
0D2Q0A0030
0D2Q0A0030
L7401
L7421
T701
0L150S1000
0L150S1000
L2000JS039
2SK2605
2SC4097
2SK2605
2SC4097
2SA1812
2SC4097
2SC4097
2SA1577
UPA1710AG
2SC4097
2SA1577
UPA1710AG
2SA1577
2SC4097
DIODES
MISCELLANEOUS PARTS
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
TA76431
BA9743AFV-E2
AC
AC
AC
AB
AC
AB
AC
AB
AC
AC
AC
AB
AE
AC
AD
AC
AC
AC
AC
SC902-2
SC902-2
YG802C06R
EC31QS10
EC31QS10
EC31QS10
HZ-18
1SS355
1SS355
1SS355
UDZ 33B
UDZ 33B
1SS355
UDZ20B
1SS355
EC31QS03L
EC31QS03L
EC31QS03L
EC31QS03L
COILS AND TRANSFORMERS
18261A(10uH)
18261A(10uH)
2J39
PACKAGED CIRCUIT
PC7301 0H723A0010
PC123
CONTROL
VR7401 0R854E1030
10k 1/10W
CAPACITORS
C7101
C7103
C7105
C7110
C7309
C7310
C7311
C7320
C7321
C7322
C7323
C7330
C7404
C7406
C7408
C7424
C7426
C7429
109
0C195C1040
0C1A9L4720
0C193A4720
0C1Q2E1030
0C1Q1E1010
0C2X5L4730
0C1Q2E4720
0C193A4720
0C1B2S4700
0C195E1040
0C195E1030
0C195E4710
0C195E1030
0C195E4710
1200
680
0.1
4700p
4700p
0.01
100p
0.047
4700p
4700p
47p
0.1
0.01
470p
470
0.01
470p
470
16V
25V
25V
250V
50V
50V
50V
250V
50V
50V
2kV
50V
50V
50V
10V
50V
50V
10V
Electrolytic
Electrolytic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Electrolytic
Ceramic
Ceramic
Electrolytic
Code
PG-M20X
Ref. No.
Part No.
★
Description
Code
Ref. No.
Part No.
★
Description
RDENCA004WJZZ
RDENCA010WJZZ
POWER UNIT (Continued)
PFC UNIT
C7451
C7452
C7453
C7454
C7455
0C195E4730
0C195E1040
0C195E1040
0C1Q1E2210
0C195E4730
R7101
R7102
R7103
R7104
R7105
R7106
R7305
R7306
R7307
R7308
R7309
R7310
R7311
R7312
R7314
R7317
R7320
R7321
R7322
R7323
R7324
R7325
R7327
R7330
R7331
R7332
R7333
R7334
R7335
R7336
R7340
R7341
R7342
R7401
R7403
R7404
R7408
R7410
R7411
R7415
R7421
R7423
R7424
R7428
R7430
R7431
R7435
R7451
R7452
R7453
R7454
R7455
R7456
R7457
R7458
R7462
R7463
R7464
R7465
0R3Q4S3910
0R3Q4S1030
0R3Q8S3320
0R3Q8S2720
0R3Q4S2220
0R3Q3V5610
0R3Q4S2230
0R390T3320
0R3Q4S3310
0R3Q4S3320
0R3Q4S1010
0R3Q8S8210
0R3Q8S4720
0R3Q8S4730
0R390T3320
0R3Q3V5610
0R3Q4S2230
0R390T1520
0R3Q4S3320
0R3Q4S2240
0R3Q8S2220
0R390T1030
0R3Q4S6820
0R3Q4S3330
0R3Q4S3330
0R3Q4S3330
0R390T5640
0R390T5640
0R390T5640
0R3Q4S3930
0R375DR330
0R3Q3V1010
0R3Q8S1030
0R3Q8S2220
0R3Q8S2220
0R3Q4S0000
0R3Q4S1520
0R3Q4S0000
0R3Q4S4700
0R3Q4S1540
0R3Q8S5620
0R3Q8S2220
0R3Q8S1220
0R3Q4S1520
0R3Q4S0000
0R3Q4S4700
0R3Q4S1540
0R3Q8S4730
0R3Q8S3930
0R3Q8S4730
0R3Q8S3930
0R3Q4S3330
0R3Q4S1240
0R3Q4S2240
0R3Q4S3300
0R3Q4S1030
0R3Q4S1030
0R3Q4S1030
0R3Q4S1220
0.047
0.1
0.1
220p
0.047
50V
50V
50V
50V
50V
INTEGRATED CIRCUITS
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
IC701
IC702
IC703
IC7501
H3151AC001
0H1R1A0010
0H1Q3A0010
0H1Q3A0010
RESISTORS
TRANSISTORS
390 1/16W
10k 1/16W
3.3k 1/16W
2.7k 1/16W
2.2k 1/16W
560 1/10W
22k 1/16W
3.3 1/4W
330 1/16W
3.3k 1/16W
100 1/16W
820 1/16W
4.7k 1/16W
47k 1/16W
3.3k 1/4W
560 1/10W
22k 1/16W
1.5k 1/4W
3.3k 1/16W
220k 1/16W
2.2k 1/16W
10k 1/4W
6.8k 1/16W
33k 1/16W
33k 1/16W
33k 1/16W
560k 1/4W
560k 1/4W
560k 1/4W
39k 1/16W
0.33 2W
100 1/10W
10k 1/16W
2.2k 1/16W
2.2k 1/16W
0
1/16W
1.5k 1/16W
0
1/16W
47 1/16W
150k 1/16W
5.6k 1/16W
2.2k 1/16W
1.2k 1/16W
1.5k 1/16W
0
1/16W
47 1/16W
150k 1/16W
47k 1/16W
39k 1/16W
47k 1/16W
39k 1/16W
33k 1/16W
120k 1/16W
220k 1/16W
33 1/16W
10k 1/16W
10k 1/16W
10k 1/16W
1.2k 1/16W
TRA701 0D513A6120
Q701 T2837KL001
Q702 0T394A0010
Q703 0T192A0010
Q711 0T394A0010
Q712 0T192A0010
Q715 0T192A0010
Q7407 0T394A0010
Q7501 0T397A0010
Q7502 0T394A0010
Q7503 0T192A0010
Z701
0D758A4710
SM12JZ47
2SK2837
2SC4081
2SA1576A
2SC4081
2SA1576A
2SA1576A
2SC4081
2SC4672K
2SC4081
2SA1576A
ENC471
DIODES
D701
D702
D703
D705
D706
D707
D708
D709
D710
D713
D714
D716
D725
D729
D730
D7501
D7503
D7504
D7505
0D118A0060
0D2Q3A0040
0D157A0060
0D157A0060
0D157A0060
0D157A0060
0D295A0080
0D295A0080
0D295A0080
0D295A0080
0D492A0020
0D157A0060
0D491A0290
0D291A0010
0D279A0100
0D265A0020
0D295A0080
0D295A0080
D15XB60
SF10L60U
EC10QS04
ERA15-06
ERA15-06
ERA15-06
ERA15-06
1SS355
1SS355
1SS355
1SS355
UDZS 5.6B
ERA15-06
UDZ 30B
EC11FS4
21DQ10 TA2B1
ERA91-02
1SS355
1SS355
PACKAGED CIRCUITS
PC701 0H723A0010
PC704 0H723A0010
PC705 0H723A0010
PC123
PC123
PC123
COILS
L701
L704
L703
L1107RL502
0L115R1110
FK-080G-5020H2
SK-10M-5YRP
HKBS-12D080-9710RS
TRANSFORMERS
T7301 L2000BS026
PTC701 0D802A1010
2B26
PTH9M04BD222TS2F333
CAPACITORS
C700
C701
C702
C703
C704
C705
C706
C707
C708
C709
C710
C711
C712
C713
C714
C715
MISCELLANEOUS PARTS
BEA7301 0L551A0020
CN7102 K2107KS012
CN7101 0WPF2013B0
FA5502M
MIP0254SPSCF
TA76431
TA76431
BL02RN2-R62 T2
MDF7P-12DP-2.54DSA
CONNECTOR
110
0C247M4740
0C245Q4740
C3105MR100
0C1H8Q2220
0C1H8Q2220
0C245Q4740
0C247M4740
C3124ML151
0C3A0D1510
0C195C1040
0C1B2S4700
0C1Q0A1060
0C195C1040
0C195C1040
C1102EC102
0C195C3330
0.47
0.47
10
2200p
2200p
0.47
0.47
150
150
0.1
47p
10
0.1
0.1
1000p
0.033
450V
AC250V
400V
AC250V
AC250V
AC250V
450V
400V
35V
25V
2kV
6.3V
25V
25V
50V
25V
Film
Film
Electrolytic
Ceramic
Ceramic
Film
Electrolytic
Electrolytic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Code
PG-M20X
Ref. No.
Part No.
★
Description
Code
RDENCA010WJZZ
PFC UNIT (Continued)
C716
C717
C718
C719
C720
C721
C722
C723
C724
C725
C726
C727
C728
C729
C730
C731
C734
C7501
C7502
C7503
C7504
C7505
C7506
C7507
C7508
C7509
0C194E4710
0C195E1030
0C195E1030
0C194E3310
0C198E4740
0C1A9R3310
0C1B2S4700
0C1H8Q3320
0C194E3310
0C195C1040
0C195E1030
0C1H8Q4710
0C1H8Q2220
0C195E1030
0C1H8Q1020
0C1H8Q1020
0C377M1R00
0C3A0A1020
0C195C1040
0C195C1040
0C195E1040
0C1Q0A1060
0C195C1040
0C198E4740
0C3A0B4710
0C198E4740
R701
R702
R703
R704
R705
R706
R707
R708
R709
R710
R711
R712
R713
R714
R715
R716
R717
R718
R719
R720
R721
R722
R723
R724
R725
R726
R736
R765
R768
R769
R771
R772
R773
R774
R775
R776
R777
R778
R779
R780
R781
R783
R784
R785
R3107SC563
0R390T1540
0R390T1540
0R390T1540
R3107SC563
0R3Q4S1010
0R522F1000
0R3Q4S1040
0R391T2240
0R391T2240
0R391T2240
0R3Q3V1000
0R391T1840
0R391T1840
0R391T1840
0R516FR050
0R3Q4S1240
0R3Q4S2700
0R390T3300
0R3Q8S1820
0R3Q8S3630
0R3Q4S3330
0R390T4700
0R3Q4S3940
0R3Q8S2220
0R3Q4S1030
0R3Q8S1030
0R390T3920
0R3Q4S2720
0R3Q8S6810
0R390T0000
0R391T1840
0R391T1840
0R391T1840
0R3Q8S5620
0R3Q0V3310
0R3Q0V5620
0R3Q4S2230
0R3Q4S6840
0R3Q0V1030
0R3Q0V1030
0R3Q4S3340
0R3Q4S1020
0R3Q4S3320
470p
0.01
0.01
330p
0.47
330p
47p
3300p
330p
0.1
0.01
470p
2200p
0.01
1000p
1000p
1
1000
0.1
0.1
0.1
10
0.1
0.47
470
0.47
50V
50V
50V
50V
50V
1kV
2kV
AC250V
50V
25V
50V
AC250V
AC250V
50V
AC250V
AC250V
400V
10V
25V
25V
50V
6.3V
25V
50V
16V
50V
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Electrolytic
Electrolytic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Electrolytic
Ceramic
Part No.
R791
R792
R793
R7466
R7467
R7468
R7469
R7501
R7502
R7503
R7504
R7505
R7508
R7509
R7514
R7515
R7516
R7517
R7518
R7519
R7520
R7521
R7522
R7523
R7524
R7525
R7526
0R390T8230
0R390T8230
0R390T8230
0R3Q4S6810
0R3Q4S1020
0R3Q4S1030
0R3Q4S1030
0R3Q4S2220
0R3Q4S8210
0R3Q4S3330
0R3Q8S3320
0R3Q8S1520
0R3Q8S1220
0R3Q3V5610
0R3Q0V1030
0R3Q4S1020
0R390T1000
0R390T1000
0R390T1000
0R390T1000
0R3Q4S1030
0R3Q4S2220
0R3Q4S1030
0R3Q4S1030
0R3Q4S5620
0R3Q0V2720
0R3Q0V2720
RL701
BEA701
BEA703
BEA704
F701
FH1
FH2
CN701
CN702
CN704
CN7001
CN7002
CN7003
CN7004
CN7103
HS1
HS2
K3102AL001
0L551A0020
0L551A0010
★
Description
82k
82k
82k
680
1k
10k
10k
2.2k
820
33k
3.3k
1.5k
1.2k
560
10k
1k
10
10
10
10
10k
2.2k
10k
10k
5.6k
2.7k
2.7k
1/4W
1/4W
1/4W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/10W
1/8W
1/16W
1/4W
1/4W
1/4W
1/4W
1/16W
1/16W
1/16W
1/16W
1/16W
1/8W
1/8W
Chip3216
Chip3216
Chip3216
Chip1608
Chip1608
Chip1608
Chip1608
Chip1608
Chip1608
Chip1608
Chip1608
Chip1608
Chip1608
Chip2012
Chip2012
Chip1608
Chip3216
Chip3216
Chip3216
Chip3216
Chip1608
Chip1608
Chip1608
Chip1608
Chip1608
MISCELLANEOU PARTS
RESISTORS
56K 1/16W
150k 1/4W
150k 1/4W
150k 1/4W
56K 1/16W
100 1/16W
10 5W
100k 1/16W
220k 1/4W
220k 1/4W
220k 1/4W
10 1/10W
180k 1/4W
180k 1/4W
180k 1/4W
0.05 3W
1120k 1/16W
127 1/16W
33 1/4W
1.8k 1/16W
36k 1/16W
33k 1/16W
47 1/4W
390 1/16W
2.2k 1/16W
10k 1/16W
10k 1/16W
3.9k 1/4W
2.7k 1/16W
680 1/16W
0
1/4W
180k 1/4W
180k 1/4W
180k 1/4W
5.6k 1/16W
330 1/8W
5.6k 1/8W
22k 1/16W
680k 1/16W
10k 1/8W
10k 1/8W
330k 1/16W
1k 1/16W
3.3k 1/16W
Ref. No.
Chip3216
Chip3216
Chip3216
Chip1608
Fuse Resistor
Chip3216
Chip3216
Chip3216
Chip2012
Chip1608
Chip1608
Chip3216
Chip1608
Chip1608
Chip1608
Chip3216
Chip1608
Chip1608
Chip1608
Chip1608
Chip1608
Chip1608
Chip3216
Chip1608
Chip2012
Chip2012
Chip1608
Chip1608
Chip2012
Chip2012
Chip1608
Chip1608
Chip1608
111
0K718A6R30
0M850A0010
0M850A0010
K2105SL001
0K251A0020
0K248A0050
K2102FS013
0WPF2014A0
0K202B0020
0K248A0020
K2106KS012
0MPF002800
0MPF002900
DG5D2-0(M)
BL02RN2-R62 T2
BL02RN1-R62 T2
BPR53RA035013030M
AC250V 6.3AH 215
TP00351-51
TP00351-51
NC-179-L2
B2P3-VH
B5B-EH-A
TWG-P13P-A1
CONNECTOR
B2B-PH-K-S
B2B-EH-A
MDF7-12D-2.54DSA(01)
Shield
Shield
Code
PG-M20X
Ref. No.
★
Part No.
Description
Code
CPCi-0057CE01
PC I/F UNIT
INTEGRATED CIRCUITS
IC3
IC4
IC5
IC6
IC7
IC8
IC10
IC11
IC13
IC15
IC16
IC25
IC29
IC28
IC30
IC319
IC320
IC321
IC322
IC330
IC331
IC298
IC363
IC364
IC365
IC366
9DK001-11020
9DK001-15115
RH-iXA148WJZZQ
9DK001-15118
RH-iXA147WJZZQ
9DK001-15112
9DK001-15117
9DK001-11023
9DK001-15113
9DK001-15119
9DK001-12xxx
RH-iXA091WJZZQ
RH-iX3399CEN1
9KD001-11028
9KD001-11028
9KD001-11024
9KD001-11024
9KD001-11024
9KD001-11024
9DK001-15089
9DK001-15089
9DK001-15090
9DK001-12107
9DK001-15114
9DK001-12103
9DK001-12105
AT24C128N-10SC-1.8
PQ05VY3H3Z
LH28F640BXXE
PST9229
HD6417709SBP133V
PQ033EZ01
PST9222
24LC21A-/SN
AD9888
SAA7118E
NC7SZ08P5X
CVIC2
IX3399
HY57V641620HGT-H
HY57V641620HGT-H
HY57V653220BTC-7
HY57V653220BTC-7
HY57V653220BTC-7
HY57V653220BTC-7
TL712CPW
TL712CPW
SiI151A
74VHC153MTC
PQ070XZ01
74LCX157MTC
74LVX125MTC
9DK001-20012
9DK001-20012
9DK001-20012
9DK001-20037
9DK001-20012
D5
D9
D28
D29
D30
D31
D33
D34
D35
D36
D37
D38
D39
D40
D41
D43
D44
D45
D46
D47
9DK001-30018
9DK001-30018
9DK001-30018
9DK001-30018
9DK001-30015
9DK001-30015
9DK001-30018
9DK001-30018
9DK001-30018
9DK001-30015
9DK001-30015
9DK001-30015
9DK001-30015
9DK001-30015
9DK001-30015
9DK001-30015
9DK001-30015
9DK001-30015
9DK001-30015
9DK001-30015
X1
X4
X5
X6
X7
RMC1
9DK001-80xxx
9DK001-80018
9DK001-80024
9DK001-80
9DK001-80015
9DK001-15121
L3
L4
L5
L6
L7
9DK001-81059
9DK001-81052
9DK001-81052
9DK001-81062
9DK001-81062
★
Part No.
L8
L11
L12
L13
L14
L15
L20
L21
L22
FL1
FL2
FL3
FL41
FL94
FL98
FL99
FL103
FL107
FL108
FL109
FL110
FL111
FL112
FL113
FL114
FL115
FL116
FL117
FL118
FL119
9DK001-81062
9DK001-81052
9DK001-81052
9DK001-81062
9DK001-81052
9DK001-81062
9DK001-81044
9DK001-81044
9DK001-81052
9DK001-82021
9DK001-82021
9DK001-81020
9DK001-81020
9DK001-81020
9DK001-82021
9DK001-82021
9DK001-81020
9DK001-82021
9DK001-82021
9DK001-82021
9DK001-82021
9DK001-82xxx
9DK001-82xxx
9DK001-82xxx
9DK001-82021
9DK001-82xxx
9DK001-82xxx
9DK001-82xxx
9DK001-82xxx
9DK001-82xxx
C3
C4
C5
C6
C7
C8
C9
C10
C12
C13
C14
C15
C16
C17
C18
C19
C20
C21
C22
C23
C24
C25
C26
C27
C28
C29
C30
C31
C33
C35
C36
C37
C38
C39
C40
C41
C42
C43
C44
C45
C46
C47
C48
C49
9DK001-42
9DK001-42099
9DK001-42105
Description
BLM21P221SG
NLC322522T-3R3M 3.3uH
NLC322522T-3R3M 3.3uH
BLM21P221SG
NLC322522T-3R3M 3.3uH
BLM21P221SG
BLM21B201S
BLM21B201S
NLC322522T-3R3M 3.3uH
BMS100
BMS100
BMK351
BMK351
BMK351
BMS100
BMS100
BMK351
BMS100
BMS100
BMS100
BMS100
NFA31GD1004704
NFA31GD1004704
NFA31GD1004704
BMS100
NFA31GD1004704
NFA31GD1004704
NFA31GD1004704
NFA31GD1004704
NFA31GD1004704
CAPACITORS
TRANSISTORS
Q1
Q2
Q3
Q4
Q5
Ref. No.
2SA1037AKQ
2SA1037AKQ
2SA1037AKQ
HN2C01FU
2SA1037AKQ
DIODES
1SS187
1SS187
1SS187
1SS187
MA157A
MA157A
1SS187
1SS187
1SS187
MA157A
MA157A
MA157A
MA157A
MA157A
MA157A
MA157A
MA157A
MA157A
MA157A
MA157A
PACKAGED CIRCUITS
CX-53F(16.588MHz)
FXO-31FL(25.000MHz)
FXO-31FL(32.500MHz)
CX-53F(24.576MHz)
MC-206(32.768kHz)
TSOP1838SS3V
COILS AND FILTERS
NLC322522T-1R0M 1.0uH
NLC322522T-3R3M 3.3uH
NLC322522T-3R3M 3.3uH
BLM21P221SG
BLM21P221SG
112
9DK001-42
9DK001-42
9DK001-42
9DK001-42131
9DK001-42103
9DK001-42103
9DK001-42
9DK001-42131
9DK001-42
9DK001-42
9DK001-42128
9DK001-42104
9DK001-42104
9DK001-40081
9DK001-42
9DK001-42
9DK001-42
9DK001-42131
9DK001-42
9DK001-42105
9DK001-42105
9DK001-42105
9DK001-42
9DK001-42
9DK001-42
9DK001-40089
9DK001-42131
9DK001-42113
9DK001-42105
9DK001-40089
9DK001-42105
9DK001-42105
9DK001-40091
9DK001-42105
9DK001-42105
9DK001-42105
9DK001-42103
9DK001-42103
9DK001-40081
9DK001-42
0.1
100p
0.047
10p
1
0.1
0.1
10
15p
15p
1
10
0.1
1
1000p
470p
470p
22
1
1
0.1
10
0.1
0.047
0.047
0.047
0.1
1
1
47
10
4.7
0.047
47
0.047
0.047
100
0.047
0.047
0.047
15p
15p
22
0.1
25V
50V
50V
50V
6.3V
25V
25V
10V
50V
50V
6.3V
10V
25V
6.3V
50V
50V
6.3V
6.3V
6.3V
25V
10V
25V
50V
50V
50V
25V
6.3V
6.3V
6.3V
10V
10V
50V
6.3V
50V
50V
4V
50V
50V
50V
50V
50V
6.3V
25V
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Electrolytic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Electrolytic
Ceramic
Ceramic
Ceramic
Electrolytic
Ceramic
Ceramic
Electrolytic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Electrolytic
Ceramic
Code
PG-M20X
Ref. No.
Part No.
★
Description
Code
C447
C448
C449
C450
C454
C457
C458
C459
C465
C468
C569
C571
C575
C576
C577
C578
C579
C580
C581
C582
C583
C584
C585
C586
C589
C590
C591
C592
C593
C594
C595
C596
C597
C598
C599
C600
C601
C602
C603
C607
C609
C611
C613
C615
C617
C619
C621
C623
C625
C627
C629
C631
C633
C635
C637
C638
C640
C641
C648
C649
C656
C658
C662
C666
C668
C670
C672
C678
C682
C685
C686
C687
C688
C689
C695
C696
CPCi-0057CE01
PC I/F UNIT (Continued)
C50
C51
C52
C53
C54
C55
C56
C57
C58
C59
C60
C61
C62
C63
C64
C65
C66
C69
C70
C71
C72
C73
C74
C75
C76
C77
C78
C81
C82
C83
C85
C140
C141
C142
C150
C151
C152
C153
C154
C155
C156
C157
C158
C159
C160
C161
C162
C163
C164
C165
C166
C167
C169
C170
C171
C174
C176
C177
C192
C197
C205
C214
C218
C366
C375
C437
C438
C439
C440
C441
C442
C444
9DK001-40081
9DK001-42
9DK001-42
9DK001-42
9DK001-42
9DK001-42
9DK001-42
9DK001-40xxx
9DK001-42105
9DK001-42105
9DK001-42
9DK001-42
9DK001-42105
9DK001-42
9DK001-42
9DK001-42
9DK001-40091
9DK001-42096
9DK001-42105
9DK001-42096
9DK001-42
9DK001-42
9DK001-42
9DK001-42
9DK001-42
9DK001-42
9DK001-42105
9DK001-42105
9DK001-42154
9DK001-40081
9DK001-42
9DK001-42105
9DK001-42105
9DK001-42105
9DK001-42
9DK001-42
9DK001-42
9DK001-42
9DK001-42
9DK001-42
9DK001-42
9DK001-42
9DK001-42
9DK001-42
9DK001-42
9DK001-42
9DK001-42
9DK001-42
9DK001-42
9DK001-42
9DK001-42xxx
9DK001-42xxx
9DK001-42
9DK001-42
9DK001-42
9DK001-42
9DK001-42
9DK001-42
9DK001-42
9DK001-42
9DK001-42
9DK001-42
9DK001-42
9DK001-40091
9DK001-40091
9DK001-42099
9DK001-42099
9DK001-42099
9DK001-42099
9DK001-40081
9DK001-42
9DK001-42099
Ref. No.
22
6.3V Electrolytic
1
6.3V Ceramic
0.1
25V Ceramic
0.1
25V Ceramic
0.1
25V Ceramic
0.1
25V Ceramic
0.1
25V Ceramic
PX4VC150MF60
0.047 50V Ceramic
0.047 50V Ceramic
0.1
25V Ceramic
1
6.3V Ceramic
0.047 50V Ceramic
0.1
25V Ceramic
0.1
25V Ceramic
0.1
25V Ceramic
100
4V
Electrolytic
0.01 50V Ceramic
0.047 50V Ceramic
0.01 50V Ceramic
0.1
25V Ceramic
0.1
25V Ceramic
0.1
25V Ceramic
0.1
25V Ceramic
0.1
25V Ceramic
0.1
25V Ceramic
0.047 50V Ceramic
0.047 50V Ceramic
0.33 10V Ceramic
22
6.3V Electrolytic
0.1
25V Ceramic
0.047 50V Ceramic
0.047 50V Ceramic
0.047 50V Ceramic
0.1
25V Ceramic
0.1
25V Ceramic
0.1
25V Ceramic
0.1
25V Ceramic
0.1
25V Ceramic
0.1
25V Ceramic
0.1
25V Ceramic
0.1
25V Ceramic
0.1
25V Ceramic
0.1
25V Ceramic
0.1
25V Ceramic
0.1
25V Ceramic
0.1
25V Ceramic
0.1
25V Ceramic
0.1
25V Ceramic
0.1
25V Ceramic
3900p 16V Film
0.039 16V Film
0.1
25V Ceramic
0.1
25V Ceramic
0.1
25V Ceramic
0.1
25V Ceramic
0.1
25V Ceramic
0.1
25V Ceramic
0.1
25V Ceramic
0.1
25V Ceramic
0.1
25V Ceramic
0.1
25V Ceramic
0.1
25V Ceramic
100
4V
Electrolytic
100
4V
Electrolytic
100p 50V Ceramic
100p 50V Ceramic
100p 50V Ceramic
100p 50V Ceramic
22
6.3V Electrolytic
1
6.3V Ceramic
100p 50V Ceramic
113
Part No.
9DK001-42131
9DK001-42122
9DK001-42122
9DK001-42122
9DK001-42131
9DK001-42123
9DK001-42123
9DK001-42123
9DK001-42123
9DK001-42123
9DK001-42
9DK001-40076
9DK001-42
9DK001-42
9DK001-42
9DK001-42
9DK001-42
9DK001-42
9DK001-42
9DK001-42
9DK001-42
9DK001-42
9DK001-42
9DK001-42
9DK001-42
9DK001-42
9DK001-42
9DK001-42
9DK001-42
9DK001-42
9DK001-42
9DK001-42
9DK001-42
9DK001-42
9DK001-42
9DK001-42
9DK001-42
9DK001-40091
9DK001-42
9DK001-42
9DK001-42
9DK001-42
9DK001-42
9DK001-42
9DK001-42
9DK001-42
9DK001-42
9DK001-42
9DK001-42
9DK001-42
9DK001-42
9DK001-42
9DK001-42
9DK001-42
9DK001-42
9DK001-42
9DK001-42
9DK001-42
9DK001-42
9DK001-42
9DK001-42
9DK001-42
9DK001-42
9DK001-42096
9DK001-42
9DK001-42
9DK001-42
9DK001-42
9DK001-42
9DK001-42
9DK001-42
9DK001-42
9DK001-42
9DK001-42
★
Description
10
180p
180p
180p
10
330p
330p
330p
330p
330p
0.1
4.7
0.1
1
1
1
1
0.1
1
1
1
0.1
0.1
1
1
1
1
1
1
0.1
0.1
1
0.1
1
1
0.1
0.1
100
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.01
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
10p
10p
10V
50V
50V
50V
10V
50V
50V
50V
50V
50V
25V
35V
25V
6.3V
6.3V
6.3V
6.3V
25V
6.3V
6.3V
6.3V
25V
25V
6.3V
6.3V
6.3V
6.3V
6.3V
6.3V
25V
25V
6.3V
25V
6.3V
6.3V
25V
25V
4V
25V
25V
25V
25V
25V
25V
25V
25V
25V
25V
25V
25V
25V
25V
25V
25V
25V
25V
25V
25V
25V
25V
25V
25V
25V
50V
25V
25V
25V
25V
25V
25V
25V
25V
25V
25V
50V
50V
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Electrolytic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Electrolytic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Code
PG-M20X
Ref. No.
★
Part No.
Description
Code
R51
R54
R63
R64
R65
R66
R67
R69
R70
R71
R72
R73
R74
R75
R80
R83
R88
R89
R91
R93
R96
R97
R104
R105
R106
R107
R109
R110
R111
R113
R114
R116
R117
R118
R119
R121
R122
R123
R124
R127
R130
R131
R134
R138
R139
R140
R143
R151
R152
R153
R155
R156
R158
R159
R160
R161
R162
R165
R166
R170
R172
R174
R176
R178
R180
R191
R192
R193
R194
R196
R199
R201
R648
R649
R654
R685
CPCi-0057CE01
PC I/F UNIT (Continued)
C697
C708
C744
C745
C746
C747
C748
C749
C750
C752
C758
C759
C901
C902
C904
C905
C906
C909
C910
C911
C912
C913
C914
C915
C916
C917
C918
C919
C920
C921
C922
C923
C924
C925
9DK001-42
9DK001-40090
9DK001-42
9DK001-42
9DK001-42112
9DK001-42
9DK001-42
9DK001-42112
9DK001-42
9DK001-42113
9DK001-42
9DK001-42
9DK001-42
9DK001-42
9DK001-42
9DK001-42
9DK001-42
9DK001-42
9DK001-42
9DK001-42
9DK001-42
9DK001-42
9DK001-42
9DK001-42
9DK001-42
9DK001-40xxx
9DK001-40091
9DK001-42154
9DK001-42
9DK001-42
9DK001-42131
0.1
25V Ceramic
47
4V
Electrolytic
0.1
25V Ceramic
0.1
25V Ceramic
33p
50V Ceramic
0.1
25V Ceramic
0.1
25V Ceramic
33p
50V Ceramic
0.1
25V Ceramic
4.7
10V Ceramic
10p
50V Ceramic
0.1
25V Ceramic
0.1
25V Ceramic
1
6.3V Ceramic
0.1
25V Ceramic
0.1
25V Ceramic
0.1
25V Ceramic
1
6.3V Ceramic
0.1
25V Ceramic
1
6.3V Ceramic
1
6.3V Ceramic
1
6.3V Ceramic
1
6.3V Ceramic
0.1
25V Ceramic
10p
50V Ceramic
1
6.3V Ceramic
0.1
25V Ceramic
PX4VC150MF60
10p
50V Ceramic
100
4V
Electrolytic
0.33 10V Ceramic
0.1
25V Ceramic
0.1
25V Ceramic
10
10V Ceramic
RESISTORS
R1
R2
R3
R4
R8
R9
R12
R13
R14
R17
R18
R19
R20
R22
R23
R25
R26
R27
R28
R29
R32
R33
R34
R35
R36
R37
R38
R39
R40
R41
R42
R45
R46
R47
R48
R50
9DK001-51030
9DK001-50149
9DK001-50179
9DK001-50149
9DK001-51030
9DK001-50219
9DK001-50185
9DK001-50165
9DK001-50
9DK001-50183
9DK001-50177
9DK001-50149
9DK001-50183
9DK001-51030
9DK001-50149
9DK001-51030
9DK001-51037
9DK001-51030
9DK001-50149
9DK001-50275
9DK001-50150
9DK001-50161
9DK001-50185
9DK001-50185
9DK001-50177
9DK001-50159
9DK001-50150
9DK001-50150
9DK001-50044
9DK001-50275
9DK001-50159
9DK001-50044
9DK001-50275
9DK001-50159
9DK001-50044
9DK001-50149
10k
0
2.2k
0
10k
47k
10k
100
100
4.7k
1k
0
4.7k
10k
0
10k
6.8k
10k
0
6.8
10
47
10k
10k
1k
22
10
10
68
6.8
22
68
6.8
22
68
0
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/4W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/10W
1/16W
1/16W
1/10W
1/16W
1/16W
1/10W
1/16W
Ref. No.
Chip
Chip1608
Chip
Chip1608
Chip1608
Chip1608
Chip3216
Chip1608
Chip1608
Chip
Chip1608
Chip
Chip
Chip
Chip1608
Chip1608
Chip1608
Chip1608
Chip1608
Chip1608
Chip1608
Chip1608
Chip1608
Chip2125
Chip1608
Chip1608
Chip2125
Chip1608
Chip1608
Chip2125
Chip
114
Part No.
9DK001-50149
9DK001-50149
9DK001-50
9DK001-50213
9DK001-50181
9DK001-50181
9DK001-51037
9DK001-50149
9DK001-50
9DK001-50
9DK001-50
9DK001-50185
9DK001-50185
9DK001-50159
9DK001-50044
9DK001-50159
9DK001-50044
9DK001-50149
9DK001-50159
9DK001-50300
9DK001-50044
9DK001-50185
9DK001-50149
9DK001-50149
9DK001-50149
9DK001-50149
9DK001-51037
9DK001-51037
9DK001-50149
9DK001-50149
9DK001-50297
9DK001-50300
9DK001-50298
9DK001-50149
9DK001-50149
9DK001-50292
9DK001-50292
9DK001-50149
9DK001-50149
9DK001-50149
9DK001-50173
9DK001-50159
9DK001-50149
9DK001-50177
9DK001-50177
9DK001-50177
9DK001-50177
9DK001-5
9DK001-42105
9DK001-42105
9DK001-42105
9DK001-42105
9DK001-42105
9DK001-42105
9DK001-42105
9DK001-50201
9DK001-50183
9DK001-50181
9DK001-50149
9DK001-50150
9DK001-50185
9DK001-50149
9DK001-50224
9DK001-50185
9DK001-50149
9DK001-50150
9DK001-50150
9DK001-50150
9DK001-50149
9DK001-50149
9DK001-51037
9DK001-50149
9DK001-50165
9DK001-50165
9DK001-50204
9DK001-50150
★
Description
0
1/16W
0
1/16W
1.07k
2.0k 1/16W
3.3k 1/16W
3.3k 1/16W
6.8k 1/16W
0
1/16W
150 1/10W
150 1/10W
150 1/10W
10k 1/16W
10k 1/16W
22 1/16W
68 1/10W
22 1/16W
68 1/10W
0
1/16W
22 1/16W
18 1/10W
68 1/10W
10k 1/16W
0
1/16W
0
1/16W
0
1/16W
0
1/16W
6.8k 1/16W
6.8k 1/16W
0
1/16W
0
1/16W
39 1/16W
18 1/10W
120 1/4W
0
1/16W
0
1/16W
3.9 1/4W
3.9 1/4W
0
1/16W
0
1/16W
0
1/16W
470 1/16W
22 1/16W
0
1/16W
1k 1/16W
1k 1/16W
1k 1/16W
1k 1/16W
560 1/16W
0.047
0.047
0.047
0.047
0.047
0.047
0.047
18 1/16W
4.7k 1/16W
3.3k 1/16W
0
1/16W
10 1/16W
10k 1/16W
0
1/16W
150 1/4W
10k 1/16W
0
1/16W
10 1/16W
10 1/16W
10 1/16W
0
1/16W
0
1/16W
6.8k 1/16W
0
1/16W
100 1/16W
100 1/16W
150 1/16W
10 1/16W
Code
Chip
Chip
1/16W
Chip1608
Chip1608
Chip1608
Chip1608
Chip
Chip
Chip2125
Chip2125
Chip2125
Chip1608
Chip1608
Chip1608
Chip2125
Chip1608
Chip2125
Chip
Chip1608
Chip2125
Chip2125
Chip1608
Chip
Chip
Chip
Chip
Chip
Chip
Chip
Chip
Chip1608
Chip2125
Chip3216
Chip
Chip
Chip3216
Chip3216
Chip
Chip
Chip
Chip1608
Chip1608
Chip
Chip1608
Chip1608
Chip1608
Chip1608
Chip1608
50V
Ceramic
50V
Ceramic
50V
Ceramic
50V
Ceramic
50V
Ceramic
50V
Ceramic
50V
Ceramic
Chip1608
Chip1608
Chip1608
Chip
Chip1608
Chip1608
Chip
Chip3216
Chip1608
Chip
Chip1608
Chip1608
Chip1608
Chip
Chip
Chip
Chip
Chip1608
Chip1608
Chip1608
Chip1608
PG-M20X
Ref. No.
Part No.
★
Description
Code
CPCi-0057CE01
PC I/F UNIT (Continued)
R688
R689
R690
R692
R693
R694
R695
R696
R697
R698
R699
R700
R701
R704
R750
R751
R752
R753
R787
R788
R789
R790
R791
R792
R801
R867
R868
R869
R977
R994
R995
R998
R999
RE1
RE2
9DK001-50201
9DK001-50173
9DK001-50205
9DK001-50159
9DK001-50159
9DK001-50159
9DK001-50159
9DK001-50185
9DK001-50185
9DK001-50185
9DK001-50185
9DK001-50218
9DK001-50257
9DK001-50185
9DK001-50177
9DK001-50177
9DK001-50170
9DK001-50170
9DK001-50244
9DK001-50177
9DK001-50177
9DK001-50179
9DK001-50244
9DK001-50179
9DK001-50205
9DK001-50275
9DK001-50275
9DK001-50275
9DK001-50150
9DK001-50236
9DK001-50199
9DK001-50177
9DK001-50
9DK001-94001
9DK001-94001
P1
P8
P9
SC1
9DK001-60053
9DK001-60077
9DK001-60075
9DK001-60076
PSLDCA002WJZZ
15 1/16W Chip1608
470 1/16W Chip1608
1.8k 1/16W Chip1608
22 1/16W Chip1608
22 1/16W Chip1608
22 1/16W Chip1608
22 1/16W Chip1608
10k 1/16W Chip1608
10k 1/16W Chip1608
10k 1/16W Chip1608
10k 1/16W Chip1608
20k 1/16W Chip1608
75 1/16W Chip1608
10k 1/16W Chip1608
1k 1/16W Chip1608
1k 1/16W Chip1608
270 1/16W Chip1608
270 1/16W Chip1608
3.9k 1/16W Chip1608
1k 1/16W Chip1608
1k 1/16W Chip1608
2.2k 1/16W Chip1608
3.9k 1/16W Chip1608
2.2k 1/16W Chip1608
1.8k 1/16W Chip1608
6.8 1/16W Chip1608
6.8 1/16W Chip1608
6.8 1/16W Chip1608
10 1/16W Chip1608
910 1/16W Chip1608
2.15k 1/16W Chip1608
1k 1/16W Chip1608
39 1/10W Chip2125
FTR-B3 GA 003Z-B10
FTR-B3 GA 003Z-B10
MISCELLANEOUS PARTS
74320-1004
FX8C-80P-SV4
FX6-40P-0.8SV
FH16-80S-0.3SHW
Shield
115
Ref. No.
Part No.
★
Description
Code
PG-M20X
CABINET AND MECHANICAL PARTS
H
U
40
1
V
M
11
W
P
35
9
48
29
H
A
1-1-7
O
G
1-12
U
V
47
1-3
1-1-4
1-5
W
1-1-8
1-1-3
C
1-1-10
Z
1-2
F
X
1-4
H
Y
12
1-1-6
38
1-6
K
I
7
11
53
36
23
B
G
E
50
40
19
46
L
Y
K
J
R
N
O
15
D
Z
34
4-1
19
4-2
M
J
S
X
I
Q
E
31
L
18
S
2-9
13
22
24
12
D
2-7
P
2-3-3
5-2
N
50
Q
5-1
2-3
14
52
37
2-3-2
F
2-6
F
C
R
C
52
2-2-5
2-6
E
24
5-2
5-2
2-6
5-2
A
2-6
D
B
2-1-1
E
2-2
2-1-5
47
2-2-9
2-6
2-1-4
2-8
2-1-2
2-2-2
2-1-3
B
A
17
2-5
2-8
2-2-4
1
2
3-1
3
3-3
8
16
4
116
5
6
PG-M20X
Ref. No.
Part No.
★
Description
Code
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
32
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
CABINET AND MECHANICAL PARTS
1
1-1
1-1-1
1-1-2
1-1-3
1-1-4
1-1-5
1-1-6
1-1-7
1-1-8
1-1-9
1-1-10
1-2
1-3
1-4
1-5
Not Available
– Top Body Unit
DBDYT1210CE01
Top Body Ass'y
Not Available
– Top Body
GCOVA2089CESA
LED Cover
GCOVA2090CESA
RC Cover
HBDGB3168CESA
Badge, "SHARP"
HiNDPA057WJSA
IQ Label
JBTN-2090CESA
Operation Button
PSLDHA006WJK0
Heat Shield
PSLDHA007WJK0
Heat Shielding Sheet
PSPAZA025WJZZ
Tape
QEARPA021WJFW
Earth Angle
LANGS0127CEFW
Speaker Fixing Angle
PMLT-A006WJZZ
Spacer
RSP-ZA004WJN1
Speaker
XEPSD26P06000
Screw, x2
2
2-1
2-1-1
2-1-2
2-1-3
2-1-4
2-1-5
2-1-6
2-2
2-2-1
2-2-2
2-2-3
2-2-4
2-2-5
CBDYU1143CE01
Not Available
DDORU1019CE01
Not Available
GLEGP9135CESA
LX-BZ3449CEFF
MSPRC0215CEFW
XREUW20-04000
DBDYU1143CE01
Not Available
HiNDP5957CEZZ
HiNDP5958CEZZ
HiNDPA050WJSA
LANGF2155CEFW
—
BL
—
AD
AD
AR
AF
AQ
AA
2-2-6
2-2-7
2-2-8
2-2-9
2-3
2-3-1
2-3-2
2-3-3
2-4
2-5
2-6
2-7
2-8
2-9
J Bottom Body Unit
– Lamp Door Unit
Lamp Door Ass'y
– Lamp Door
Leg(Rear)
Screw, x1
Spring
E-ring
Bottom Body Ass'y
– Bottom Body
Model Label
Caution Label
Heat Caution Label
Kensington Security
Standard Connector
LHLDZ2193CEK0
Holder
LX-NZ3183CEFW
Insert Nut, x3
LX-NZ3184CEFW
Insert Nut, x4
QEARP0007WJFW
Earth Angle
DCOVA2092CE01
Exhaust Cover Ass'y
Not Available
– Exhaust Cover
PSLDHA002WJK0
Spacer, Heat Shielding
PSLDWA001WJKZ
Punching, Exhaust Cover
GLEGP1034CESA
Leg, Right
GLEGP3034CESA
Leg, Left
PSPAT0013CEZZ
Tape
QCNW-A317WJZZ
Leaf SW
XEBSD26P08000
Screw, x2
XEBSN26P08000
Screw, x4
AM
AM
AC
AF
AA
AA
3
3-1
3-2
3-3
Not Available
DCOVA2091CE01
Not Available
HiNDP5954CESA
J Terminal Cover Unit
Terminal Cover Ass'y
– Terminal Cver
Indicatio Label
AT
—
AD
4
4-1
4-2
4-3
CHLDZ2191CE01
Not Available
PSPAT0013CEZZ
PSPAZA035WJZZ
J Ballast Unit Holder Ass'y
– Ballast Unit Holder
Tape, x2
Spacer, x2
—
AC
5
5-1
5-2
CHLDZ2200CE01
Not Available
PMLT-A007WJZZ
J Fan Holder Ass'y
– Fan Holder
Spacer, x5
—
6
Refer to Optical Mechanism Parts
7
8
9
10
11
12
13
14
CCAPHA001WJ01
GCOVD0103CESA
LANGHA001WJFW
LHLDW0106CEZZ
LX-BZ3248CEFD
LX-LZ1011GE00
NFANR0129CEZZ
NFANR0130CEZZ
Lens Cap
J Terminal Cover
Cover Angle
J Holder
J Screw, x5
J Clip Screw, x2
J Cooling Fan
J Cooling Fan
Ref. No.
—
AD
AA
BM
—
AD
AD
AD
AD
—
AF
AA
AC
AU
AU
117
Part No.
NSFTZ0170CEFW
NSFTZ0183CEFW
PSLDM4719CEFW
QEARPA033WJFW
PSPAT0013CEZZ
PSPAZA034WJZZ
PSPAZA035WJZZ
PZETK0143CEKZ
PZETK0144CEKZ
PZETK0145CEKZ
PZETK0146CEKZ
QCNW-A074WJZZ
QCNW-A075WJZZ
QCNW-A076WJZZ
QCNW-A078WJZZ
QCNW-A515WJZZ
QPWBHB399WJZZ
TLABN0433CEZZ
TLABN0458CEZZ
TLABNA002WJZZ
DUNTKB065DE01
DUNTKB066DE01
DUNTKB067DE01
CPCi-0057CE01
RDENCA004WJZZ
RDENCA005WJZZ
RDENCA010WJZZ
PSLDCA002WJZZ
XBBSN26P06000
XBPSD26P06JS0
XBPSD30P08KS0
XBPSD30P12JS0
XBPSF30P06000
XEBSD26P08000
XEBSN26P08000
XEBSN30P06000
XEPSD26P09WS0
XEPSF26P06000
XEPSF30P25XS0
UBNDT0013CEZZ
★
Description
Code
J Hexagon Screw, x3
AD
J Hexagon Screw, x2
AD
J Terminal Shield
AF
Earth Angle
J Tape, x14
AC
Spacer for Fan, x7
Spacer for Fan, x4
J Ballast Unit Cover
AL
J Cover(top)
AM
J Cover(Bottom)
AL
Cover fot PFC Unit
Connecting Cord(CW)
AD
Connecting Cord(BA)
AF
Connecting Cord(FB)
AD
Connecting Cord(KY)
AE
Connecting Cord(DE)
Connecting Cord
J Serial No. Label(PG-M20XU)
J Serial No. Label(PG-M20XE)
Serial No. Label(PG-M20XX)
Formatter Unit
Input Unit
Operation Unit
J PC I/F Unit
CW
PFC Unit
BT
Ballast Unit
BZ
Power Unit
BP
Noise Shield
J Screw
J Screw
AA
J Screw
AA
J Screw
AA
J Screw
AA
J Screw
AA
J Screw
AA
J Screw
AA
J Screw
AB
J Screw
AA
J Screw
J Lens Cap Strap
AF
PG-M20X
OPTICS MECHANISM PARTS
6-48
6-57
H
6-51
6-35
6-48
6-13
6-45
G
6-21
V
6-46
W
6-52
6-18
U
6-12
6-20
6-16
6-21
6-30
6-17
F
6-50
6-28
6-22
6-34
6-27
6-15
6-10
6-24
6-36
E
6-23
6-9
6-7
6-5
6-25
G
6-29
D
6-7
6-6
6-30 Z
6-31
Y
6-3
6-3
C
6-1
33
6-2
L
B
6-36
6-56
6-43
6-40
6-41
6-53
A
6-54
6-55
X
1
2
3
4
118
5
6
PG-M20X
Ref. No.
Part No.
★
Description
Code
OPTICS MECHANISM PARTS
6
6-1
6-2
6-3
6-4
6-5
6-6
6-7
6-8
6-9
6-10
6-11
6-12
6-13
6-14
6-15
6-16
6-17
6-18
6-19
6-20
6-21
6-22
6-23
6-24
6-25
6-26
6-27
6-28
6-29
6-30
6-31
6-32
6-33
6-34
6-35
6-36
6-37
6-38
6-39
6-40
6-41
6-41-1
6-41-2
6-41-3
6-42
6-43
6-44
6-45
6-46
6-47
6-48
6-49
6-50
6-51
6-52
6-53
6-54
6-55
6-56
6-57
CCHSK0106CE01
10A1018602
PLNS-0243CEZZ
CLMPFA001CE01
RMOTBA001WJZZ
XBBSF26P05000
11B1018812
49B1019446
12B1018810
71B1018838
XBPSF30P06000
60B1035321
72B1018840
72B1019698
NFANR0140CEZZ
NFANR0139CEZZ
60B1035437
55B1035320
53B1019321
187B1019601
72B1018837
110A1018253
NFANSA001WJZZ
41B1019319
71B1019323
71B1019327
XBBSF26P05000
55B994086
XBPSF30P06000
39B1035436
187B1035323
27B1018652
60B1018653
XBPSD30P06J00
XBBSF26P05000
LHLDZ0140CEKZ
CHLDZ0141CE01
LHLDZ0141CEKZ
MSPRP0224CEFW
PRDAR0113CEFW
XBPSD30P12JS0
PRDAR0114CEFW
XBPSD30P08KS0
LANGQA004WJ00
LANGQA006WJFW
PSPAKA006WJZZ
XBBSF26P05000
PSPAZA051WJZZ
PSPAZA058WJZZ
XBPSF30P06000
PCOVNA002WJK0
RDMDPA002WJZZ
QSOCZA015WJZZ
XBPSD30P08KS0
XBPSD30P12JS0
QCNW-A522WJZZ
Optics Engine Ass'y
Optics Engine
Projection Lens
Lamp Case Ass'y
Screw, x4
Color Wheel
Color Wheel Fixing Angle
Screw, x3
Screw, x4
Color Wheel Fixing Cover
Heat Shielding Plate
Lamp Box
Duct
Screw, x1
Spacer
Exhaust Punching
Exhaust Punching
Cooling Fan
Cooling Fan
Partation Plate
Oscillation Prevent Rubber, x6
Screw, x6
Tape
Shield(Top)
Sensor Unit Ass'y
Screw
Blow Fan
Lamp Fixing Plate
Lamp Cooling Duct(Upper)
Lamp Cooling Duct(Lower)
Screw, x2
Screw, x2
Oscillation Prevent Washer, x2
Screw, x1
Exhaust Guide Plate
Tape
DMD Spacer
DMD Fixing Sapcer
Screw, x2
Screw, x1
Outer Flame
Backer Plate Ass'y
Backer Plate
Stud Spring
Stud
Screw, x4
Heat Dissipation Plate
Screw, x2
Thermistor Fixing Angle
Thermistor Fixing Angle
Spacer for Thermistor
Screw, x3
Spacer for Exhaust Duct
Spacer fot Exhaust Duct(Lower)
Screw, x1
Exhaust Guide Plate
DMD Unit
C-spring
Screw, x2
Screw, x4
Thermistor
119
Ref. No.
Part No.
★
Description
Code
PG-M20X
Ref. No.
Part No.
★
Description
Code
Ref. No.
Part No.
★
Description
Code
PACKING PARTS
SUPPLIED ACCESSORIES
(NOT REPLACEMENT ITEM)
CCAPHA001WJ01
GCASN0005CESA
GCOVD0103CESA
QACCB5024CENA
Lens Cap
J Carrying Bag
BC
J Terminal Cover
J Power Cord(for U.K., Hong KongAZ
and Singapore)
QACCDA007WJPZ
Power Cord(for U.S., Canada) AR
QACCL3022CEZZ J Power Cord(for Australia,
AZ
New Zealand and Oceania)
QACCV4002CEZZ J Power Cord(for Europe)
AZ
QCNWG0001WJPZ
USB Cable
QCNWGA010WJZZ
DVI to 15-pin D-sub Cable AU
RRMCGA013WJSA
Remote Control
AW
TCADE3018CEZZ J Questionnaire Card
TGAN-1710CEZZ
Guarantee Card(for U.S.)
TGAN-A018WJZZ
Guarantee Card(for U.S.)
TGAN-A019WJZZ
Guarantee Card(for Canada)
TGAN-A020WJZZ
Guarantee Card(for Canada)
TGANE0050TAZZ
J Guarantee Card(PG-M20XX) AE
TiNS-7609CEZZ
J Operation Manual
AQ
TiNS-7610CEZZ
J Quick Reference Guides
AG
TiNS-7612CEZZ
J Quick Reference Guides
AG
(for Europe)
TiNS-7614CEZZ
J Quick Reference Guides
AG
(for Europe)
UBNDT0013CEZZ J Lens Cap Strap
AF
UDSKA0058CEN1 J CD-ROM
AM
SPAKAA015WJZZ
SPAKC5669CEZZ
SPAKF0552CEZZ
SPAKPA016WJZZ
SPAKX2992CEZZ
SSAKA0170CEZZ
TLABK0001TAZZ
120
–
–
–
–
–
–
Partation Board
Packing Case
Sleeve
Polystylene Cover
Buffer Material
Polystylene Cover,
for Accessories
– Carton Label
—
—
—
—
—
—
—
PG-M20X
PACKING OF THE SET
Sleeve
(SPAKCF0552CEZZ)
Polystylene Cover
(SPAKPA016WJZZ)
Buffer Material
(SPAKX2992CEZZ)
Carrying Bag
(GCASN0005CESA)
Terminal Cover
(GCOVD0103CESA)
Power Cord
(for U.K., Hong Kongand Singapore)
(QACCB5024CENA)
Power Cord(for U.S., Canada)
(QACCDA007WJPZ)
Power Cord(for Australia,New Zealand and Oceania)
(QACCL3022CEZZ)
Power Cord(for Europe)
(QACCV4002CEZZ)
USB Cable
(QCNWG0001WJPZ)
DVI to 15-pin D-sub Cable
(QCNWGA010WJZZ)
Remote Control
(RRMCGA013WJSA)
Questionnaire Card
(TCADE3018CEZZ)
Guarantee Card(for U.S.)
(TGAN-1710CEZZ)
Guarantee Card(for U.S.)
(TGAN-A018WJZZ)
Guarantee Card(for Canada)
(TGAN-A019WJZZ)
Guarantee Card(for Canada)
(TGAN-A020WJZZ)
Guarantee Card(PG-M20XX)
(TGANE0050TAZZ)
Operation Manual
(TiNS-7609CEZZ)
Quick Reference Guides
(TiNS-7610CEZZ)
Quick Reference Guides (for Europe)
(TiNS-7612CEZZ)
Quick Reference Guides (for Europe)
(TiNS-7614CEZZ)
Lens Cap Strap
(UBNDT0013CEZZ)
CD-ROM
(UDSKA0058CEN1)
Partation Board
(SPAKAA015WJZZ)
Packing Case
(SPAKC5669CEZZ)
Use tape to fix the top
side of packing xase.
Front
Carton Label
(TLABK0001TAZZ)
Use 6 staples to
fix the bottom side
of packing case.
121
PG-M20X
COPYRIGHT © 2002 BY SHARP CORPORATION
ALL RIGHTS RESERVED.
No part of this publication may be reproduced,
stored in a retrieval system, or transmitted in
any form or by any means, electronic, mechanical,
photocopying, recording, or otherwise, without
prior written permission of the publisher.
D Japan P Japan TQ0000-S
Mar. 2002 Printed in Japan
In Japan gedruckt
SY. KG
SHARP CORPORATION
AV Systems Group
Quality & Reliability Control Center
Yaita, Tochigi 329-2193, Japan