Samsung AV-R610 Instruction manual

AV-R610 XAC ENG-1
5/5/06 14:4212:0
Page 2
SAMSUNG ELECTRONICS CANADA, INC.
HEADQUARTERS
55 Standish Court Mississauga, Ontario L5R 4B2 Canada
TEL: 1-905-542-3535
www.samsung.ca
SERVICE DIVISION
55 Standish Court Mississauga, Ontario L5R 4B2 Canada
1-800-SAMSUNG (1-800-726-7864)
AH68-01853S
AV-R610 XAC ENG-1
5/5/06 14:4212:0
Page 3
Digital Surround
AV Receiver System
HT-AS610
Instruction Manual
(AV-R610)
AV-R610 XAC ENG-1
5/5/06 14:4212:0
Page 2
Safety Warnings
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT OPEN
CAUTION:
TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE REAR COVER.
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
Note to CATV system installer :
This reminder is provided to call the CATV system
installer’s attention to Section 820~40 of the NEC
which provides guidelines for proper grounding and,
in particular, specifies that the cable ground shall be
connected to the grounding system of the building,
as close to the point of cable entry as practical
This symbol indicates that dangerous voltage which can cause electric shock is present inside
this unit.
This symbol alerts you to important operating and maintenance instructions accompanying
the unit.
WARNING : To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture.
CAUTION : TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY
INSERT.
2
AV-R610 XAC ENG-1
5/5/06 14:4212:0
Page 3
Precautions
PREPARATION
VOLUME
Ensure that the AC power supply in your house complies with the identification sticker located on the back of your player. Install
your player horizontally, on a suitable base (furniture), with enough space around it for ventilation (3~4inches). Make sure the
ventilation slots are not covered. Do not stack anything on top of the player. Do not place the player on amplifiers or other
equipment which may become hot. Before moving the player, ensure the disc tray is empty. This player is designed for
continuous use. Switching off the DVD player to the stand-by mode does not disconnect the electrical supply. In order to
disconnect the player completely from the power supply, remove the main plug from the wall outlet, especially when left unused
for a long period of time.
During thunderstorms, disconnect AC main plug from
the wall outlet.
Voltage peaks due to lightning could damage the unit.
Do not expose the unit to direct sunlight or other heat
sources.
This could lead to overheating and malfunction of the
unit.
Protect the player from moisture(i.e. vases) , and excess
heat(e.g.fireplace) or equipment creating strong magnetic or
electric fields (i.e.speakers...). Disconnect the power cable from
the AC supply if the player malfunctions. Your player is not
intended for industrial use.
Use of this product is for personal use only.
Condensation may occur if your player or disc have been
stored in cold temperatures.
If transporting the player during the winter, wait approximately
2 hours until the unit has reached room temperature before using.
The battery used with this product contain chemicals
that are harmful to the environment.
Do not dispose of batteries in the general household
trash.
3
AV-R610 XAC ENG-1
5/5/06 14:4212:0
Page 4
Features
Digital AV Receiver
This product is a pure digital AV receiver that performs digital signal processing to minimize
signal distortion and loss.
Dolby Pro Logic II
Dolby Pro Logic II is a new form of multi-channel audio signal
decoding technology that improves upon existing Dolby Pro Logic.
DTS (Digital Theater Systems)
DTS play backs 5.1 channel sound with less compression than Dolby
Digital for richer sound.
SFE(Sound Field Effect) Using 24bit Audio DSP
Provides more realistic surround sound with normal stereo audio sources.
4
AV-R610 XAC ENG-1
5/5/06 14:4212:0
Page 5
Contents
PREPARATION
PREPARATION
Safety Warnings ..............................................................................................................2
Precautions......................................................................................................................3
Features ..........................................................................................................................4
Description ......................................................................................................................6
CONNECTIONS
Connecting the Speakers ................................................................................................10
Connecting External Components ..................................................................................12
Connecting the FM and AM Antennas.............................................................................15
OPERATION
Before Using the AV Receiver .........................................................................................16
Selecting Digital/Analog Input .........................................................................................18
Setting the Speaker Mode ...............................................................................................20
Setting the Speaker Listening Distance .........................................................................22
Setting Digital Input .........................................................................................................24
Setting DRC (Dynamic Range Compression) .................................................................25
Test Tone ........................................................................................................................26
Setting Speaker Level .....................................................................................................28
Dolby Pro Logic ll Mode..................................................................................................30
Dolby Pro Logic ll Effect .................................................................................................32
SFE Mode........................................................................................................................34
Stereo Mode ....................................................................................................................36
RADIO OPERATION
Listening to Radio ...........................................................................................................38
Presetting Radio Stations ...............................................................................................39
MISCELLANEOUS
Convenient Functions......................................................................................................40
Operating TV with Remote Control..................................................................................42
Operating your VCR (DVD) with Remote Control............................................................44
Before Calling for Service................................................................................................46
Specifications ..................................................................................................................48
WARRANTY ....................................................................................................................49
5
AV-R610 XAC ENG-1
5/5/06 14:4212:0
Page 6
Description
[ Front Panel ]
FUNCTION button
SELECT (
INPUT MODE button
TUNING (
POWER STANDBY Indicator
,
,
) button
) button
HEADPHONE Jack
SURROUND button
SETUP button
POWER button
VOLUME CONTROL
[ Display ]
DTS
LIVE SURROUND
INDICATOR
INDICATOR
DOLBY
INDICATOR
L.PCM
INDICATOR
SPEAKER INDICATOR
DOLBY DIGITAL
INDICATOR
RADIO FREQUENCY
INDICATOR
DIGITAL INDICATOR
DOLBY PRO
LOGIC II
INDICATOR
RADIO STEREO INDICATOR
RADIO BROADCASTING
RECEIVING INDICATOR
FRONT DISPLAY
6
AV-R610 XAC ENG-1
5/5/06 14:4212:0
Page 7
AM ANTENNA
JACK
FM ANTENNA
JACK
VCR/SAT VIDEO INPUT
JACK
VCR VIDEO OUTPUT
JACK
DVD VIDEO INPUT
JACK
DVD OPTICAL DIGITAL
AUDIO INPUT JACK
CD COAXIAL DIGITAL
AUDIO INPUT JACK
FRONT SPEAKER
TERMINALS
MONITOR VIDEO
OUTPUT JACK
PREPARATION
[ Rear Panel ]
COOLING FAN
SUBWOOFER SPEAKER TERMINALS
SURROUND SPEAKER TERMINALS
CENTER SPEAKER TERMINALS
DVD AUDIO INPUT JACKS
VCR/SAT AUDIO INPUT JACKS
CD AUDIO INPUT JACKS
VCR AUDIO OUTPUT JACKS
SUBWOOFER OUTPUT JACKS 1, 2
√√ Accessories œœ
Remote Control
AM Antenna
FM Antenna
User’s Manual
7
AV-R610 XAC ENG-1
5/5/06 14:4212:0
Page 8
Description
[ Remote Control ]
TV button
AMP button
DVD button
VCR button
DIMMER button
POWER button
TV VIDEO, FUNCTION button
CD button
NUMBER(0~9) buttons
VCR/SAT button
DVD button
SLEEP button
MO/ST button
DRC button
TUNER button
INPUT MODE DIGITAL button
INPUT MODE ANALOG button
EXTERNAL DEVICE PLAYBACK button
MUTE button
VOLUME CONTROL button
MENU button
TUNER/CHANNEL button
TUNING MODE button
CUSOR/ENTER button
SUBWOOFER button
INFO button
STEREO button
SPK DISTANCE button
SPK LEVEL button
SFE MODE button
8
TUNER MEMORY button
MODE button
EFFECT button
TEST TONE button
SPK SELECT button
AV-R610 XAC ENG-1
5/5/06 14:4212:0
Page 9
PREPARATION
Insert Remote Batteries
1
Remove the battery
cover in the direction
of the arrow.
2
Insert two 1.5V AAA
batteries, paying
attention to the correct
polarities (+ and –).
3
Replace the battery
cover.
Follow these precautions to avoid leaking or cracking batteries:
• Place batteries in the remote control so they match the polarity:(+) to (+)and (–)to (–).
• Use the correct type of batteries.Batteries that look similar may differ in voltage.
• Always replace both batteries at the same time.
• Do not expose batteries to heat or flame.
Range of Operation of the Remote Control
The remote control can be used up to approximately 23 feet/7 meters in a straight line. It can also be operated
at a horizontal angle of up to 30° from the remote control sensor.
9
AV-R610 XAC ENG-1
5/5/06 14:4212:0
Page 10
Connecting the Speakers
Before moving or installing the product, be sure to turn off the power and disconnect the power cord.
SL
SR
Position of AV Receiver
Surround Speakers
• Place AV Receiver on a dedicated stand or rack.
• Place these speakers behind your listening position.
• If there isn't enough room, place these speakers so they
face each other.
• Place them about 60 to 90cm (2 to 3feet) above your ear,
facing slightly downward.
❈ Unlike the front and center speakers, the surround
speakers are used to handle mainly sound effects and
sound will not come from them all the time.
Front Speakers
• Place these speakers in front of your listening
position, facing inwards (about 45°) toward you.
• Place the speakers so that their tweeters will be at
the same height as your ear.
• Align the front face of the front speakers with the
front face of the center speaker or place them
slightly in front of the center speakers.
Subwoofer
• The position of the subwoofer is not so critical.
Place it anywhere you like.
Center Speaker
• It is best to install it at the same height as the front
speakers.
• You can also install it directly over or under the TV.
• When you attach the speakers to a wall, make sure to
fasten them tightly so they do not fall off.
10
AV-R610 XAC ENG-1
5/5/06 14:4212:0
Page 11
ACTIVE SUBWOOFER
(not supplied)
FRONT (R)
PS-AF610
FRONT (L)
PS-AF610
SURROUND (R) SURROUND (L)
PS-AR610
PS-AR610
CONNECTIONS
• If more bass is desired, you can
connect an additional active
subwoofer (not supplied) to the
Subwoofer 1or 2 port. Since the
signal on the Subwoofer 1and 2 ports
is not stereo, you will hear the same
mono bass sound regardless of the
port you connect to.
MAIN UNIT
AV-R610
SYSTEM MODEL NAME : HT-AS610
MAIN UNIT
FRONT SPEAKER
CENTER SPEAKER
SURROUND SPEAKER
PASSIVE SUB WOOFER
AV-R610
PS-AF610
PS-AC610
PS-AR610
PS-AW610
CENTER
PS-AC610
PASSIVE
SUBWOOFER
PS-AW610
√ Connecting Speaker Wire
1
Press the tab of the
speaker connector.
Caution
2
Insert the black wire into the black(-)
terminal and the gray wire into the
red(+) terminal.
• Keep the subwoofer speaker out of reach of children so as to prevent children from inserting their hands or alien
substances into the duct (hole) of the subwoofer speaker.
• Do not hang on the wall through the duct (hole).
• Never touch speaker terminals while the power is on.
Doing so could result in electric shock.
• Make sure the polarities (+ and -) are correct.
11
AV-R610 XAC ENG-1
5/5/06 14:4212:0
Page 12
Connecting External Components
Connecting Video Component
Before moving or installing the product, be sure to turn off the power and disconnect the power cord.
DVD Player
Video Projector
• Disconnect the power plug from the outlet if you will not use this unit for a long period of time.
• In a DVD/CD player, you can select one digital audio input from OPTICAL and COAXIAL.
12
AV-R610 XAC ENG-1
5/5/06 14:4212:0
Page 13
SAT(Settop Box)
CONNECTIONS
• If using VCR, connect Analog Audio Out to VCR/SAT
Audio In on this unit. If using STB, connect Digital
Out to the SAT Optical connector on this unit.
• The Analog Audio and Video In jacks of the main unit
are used for SAT and VCR. You cannot connect both
devices at the same time.
• If there is a Digital Out for the satellite/cable STB, it
can be connected to the SAT Optical connector on
the rear panel to provide multi-channel surround. If
there is no Digital Out connector on the STB, connect
the Analog Audio Out connector to the VCR/SAT
Audio In on the unit.
• If the external component has only one Audio Output
jack, connect it to either the right or left Audio Input
jack of the main unit.
• Connect the audio cable's red plug to the red jack
and white cable to the white jack.
TV
VCR
13
AV-R610 XAC ENG-1
5/5/06 14:4212:0
Page 14
Connecting External Components
Connecting Audio Component
Before moving or installing the product, be sure to turn off the power and disconnect the power cord.
CD Player
14
AV-R610 XAC ENG-1
5/5/06 14:4212:0
Page 15
Connecting the FM and AM Antennas
If AM reception is poor, connect an
outdoor AM antenna(not supplied).
CONNECTIONS
AM Loop Antenna
(supplied)
FM Antenna (supplied)
Snap the tabs on the loop into the
slots of the base to assemble the
AM loop antenna.
FM antenna connection
1. Connect the FM antenna supplied to the FM
75 COAXIAL terminal as a temporary measure.
2. Slowly move the antenna wire around until you
find a location where reception is good, then
fasten it to a wall or other rigid surface.
COOLING FAN
AM antenna connection
1. Connect the AM loop antenna supplied to the AM
and terminals.
2. If reception is poor, connect an outdoor single
vinyl-covered wire to the AM terminal.
(Keep the AM loop antenna connected).
The cooling fan dissipates the heat generated inside the unit so that the unit can
be operated normally. The cooling fan is activated automatically to supply cool air
to the unit.
Please observe the following cautions for your safety.
• Make sure the unit is well-ventilated. If the unit has poor ventilation, the temperature inside may
rise and cause damage to it.
• Do not obstruct the cooling fan or ventilation holes. (If the cooling fan or ventilation holes are
covered with a newspaper or cloth, heat may build up inside the unit and fire may result.)
15
AV-R610 XAC ENG-1
5/5/06 14:4212:0
Page 16
Before Using the AV Receiver
Turning On/Off
REMOTE CONTROL
Press the POWER button of the remote control.
• This unit will be turned on or set to Standby mode.
MAIN UNIT
1 Connect the power plug to the outlet.
2 Press the POWER button of the main unit.
• This unit will be turned on or set to Standby mode.
Functions of Dedicated Remote Control
You can operate your AMP, TV, DVD, VCR with one remote control.
See pages 42-45 for more details.
16
AV-R610 XAC ENG-1
5/5/06 14:4212:0
Page 17
To Select the Function
REMOTE CONTROL
Method 1
Press the FUNCTION button.
• Each time you press the this button, FM ➝ AM ➝ DVD ➝ VCR/SAT ➝ CD
will be selected in turn.
Method 2
Press CD, VCR/SAT, DVD or TUNER button.
• You can directly select CD, VCR/SAT, DVD or TUNER.
Press FUNCTION button.
• Each time you press the this button, FM ➝ AM ➝ DVD ➝ VCR/SAT ➝ CD
will be selected in turn.
17
OPERATION
MAIN UNIT
AV-R610 XAC ENG-1
5/5/06 14:4212:0
Page 18
Selecting Digital/Analog Input
You can listen to sound in Analog 2 Channels or Dolby Digital 5.1 Channel using this unit.
REMOTE CONTROL
For DVD Function
Press the INPUT MODE DIGITAL button.
• DVD OPTICAL or COAXIAL will be selected.
or
Press the INPUT MODE ANALOG button.
• DVD ANALOG will be selected.
For CD Function
Press the INPUT MODE DIGITAL button.
• CD OPTICAL or COAXIAL will be selected.
or
Press the INPUT MODE ANALOG button.
• CD ANALOG will be selected.
18
AV-R610 XAC ENG-1
5/5/06 14:4212:0
Page 19
MAIN UNIT
For DVD Function
Press the INPUT MODE button.
OPERATION
• DVD OPTICAL or COAXIAL and DVD ANALOG will be selected repetitively.
For CD Function
Press the INPUT MODE button.
• CD OPTICAL or COAXIAL and CD ANALOG will be selected repetitively.
• You can enjoy Dolby Digital only if you connect the Digital Audio Output jack
of an external audio component to the optical/coaxial Digital Audio Input jack
on the main unit.
• The digital input mode is set to either OPTICAL or COAXIAL, depending on
the setting of <SETUP> ➝ <DIGITAL IN>.
19
AV-R610 XAC ENG-1
5/5/06 14:4212:0
Page 20
Setting the Speaker Mode
Before moving or installing the product, be sure to turn off the power and disconnect the power cord.
Frequency response from the speaker will be adjusted according to your speaker configuration and whether certain
speakers are used or not.
√
REMOTE CONTROL
SPK SELECT button to select the speaker you want.
1 Press
Each time you press this button, F.SPK ➝ C.SPK ➝ S.SPK ➝ SW SPK ➝
•
CROVR ➝ SPK MODE OFF will be selected in turn.
2 Press …† button to set the speaker mode.
To Exit Setup Mode
• Wait for about 5 seconds or press the SPK SELECT button of the remote control to
select SPK MODE OFF.
To turn the SUBWOOFER On or Off.
Press SUBWOOFER button.
• Each time you press this button, SW SPK : YES, SW SPK : NO will be selected in turn.
• If you play in 2 Channel Stereo, select 'YES' to use Subwoofer and 'NO' not to use.
• If F.SPK is set to ‘SMALL’, SW SPK is automatically set to ‘YES’.
20
AV-R610 XAC ENG-1
5/5/06 14:4212:0
Page 21
MAIN UNIT
SETUP button.
1 Press
“SETUP MODE” appears on the display and enters into Setup Mode.
•
OPERATION
2 Press FUNCTION button 1 time.
• “SPK SETUP” appears in the display.
3 Press SURROUND button to select the speaker you
want.
• Each time you press this button, F.SPK ➝ C.SPK ➝ S.SPK ➝ SW SPK
➝ CROVR will be selected in turn.
4 Press SELECT (
,
) button to set the speaker
mode.
To Exit Setup Mode
• Wait for about 5 seconds or press SETUP button.
“SETUP MODE OFF” appears on the display and exits Setup Mode.
Setting the Speaker
• F.SPK (Front) : LARGE, SMALL
• C.SPK (Center) : LARGE, SMALL, NONE
• S.SPK (Surround) : LARGE, SMALL, NONE
• SW SPK (Subwoofer) : YES, NO
• CROVR (Crossover Frequency) : 60, 80, 100, 120, 150, 180, 200Hz
• LARGE : Select when you use large speaker. You can listen to full
range sound.
• SMALL : Select this when you use small speaker.
Bass below 100Hz will not be output.
• NONE : Select this when you use no speaker.
• YES(Subwoofer) : Select this when you use Subwoofer
Speaker.
• NO(Subwoofer) : Select when you do not use Subwoofer
Speaker.
• CROVR: Select the crossover frequency for the best bass
response in your room.
21
AV-R610 XAC ENG-1
5/5/06 14:4212:0
Page 22
Setting the Speaker Listening Distance
√
REMOTE CONTROL
1 Press the SPK DISTANCE button to select the speaker
you want.
• Each time you press this button, F.L ➝ CEN ➝ F.R ➝ S.R ➝ S.L ➝ S.W
➝ DIST OFF will be selected in turn.
…† button to set the speaker distance.
2 Press
For F.L, CEN, F.R, S.W, S.R, S.L Speaker, you can set the distance from
•
the speaker to listening position between 1~30 feet in intervals of 1 feet.
To Exit Setup Mode
• Wait for about 5 seconds or press the SPK DISTANCE button of remote control to
select DIST OFF.
• If the listening position is beyond the range of speaker
distance setup when you place the speaker, set the
speaker distance to the maximum.
22
AV-R610 XAC ENG-1
5/5/06 14:4212:0
Page 23
MAIN UNIT
SETUP button.
1 Press
“SETUP MODE” appears on the display and enters into Setup Mode.
2 Press FUNCTION button 2 times.
•
SURROUND button to select the speaker you want.
3 Press
Each time you press this button, F.L ➝ CEN ➝ F.R ➝ S.R ➝ S.L ➝
•
S.W will be selected in turn.
SELECT( , ) button to set the speaker distance.
4 Press
For F.L, CEN, F.R, S.W, S.R, S.L Speaker, you can set the distance from the
•
speaker to listening position between 1~30 feet in intervals of 1 feet.
To Exit Setup Mode
• Wait for about 5 seconds or press SETUP button.
“SETUP MODE OFF” appears on the display and exit Setup Mode.
Setting Speaker Distance
Set the distance from the speaker to listening position in intervals of 1 feet.
• F.L (Front-Left) : 1 feet ~ 30 feet
• CEN (Center) : 1 feet ~ 30 feet
• F.R (Front-Right) : 1 feet ~ 30 feet
• S.R (Surround-Right) : 1 feet ~ 30 feet
• S.B (Surround Center) : 1 feet ~ 30 feet
• S.L (Rear-Left) : 1 feet ~ 30 feet
• SW (Subwoofer) : 1 feet ~ 30 feet
23
OPERATION
• “DIST SETUP” appears on the display.
AV-R610 XAC ENG-1
5/5/06 14:4212:0
Page 24
Setting Digital Input
You can set the digital input for a DVD/CD player to either OPTICAL or COAXIAL.
MAIN UNIT
SETUP button.
1 Press
“SETUP MODE” appears on the display and enters into Setup Mode.
2 Press FUNCTION button 3 times.
•
• “DIGITAL IN” appears on the display.
SURROUND button to select the DVD or CD function.
3 Press
Each time this button, DVD
CD will be selected in turn.
4 Press SELECT( , ) button to set the digital input.
•
• Each time you press this button, OPTICAL
COAXIAL will be selected in turn.
To Exit Setup Mode
• Wait for about 5 seconds or press SETUP button.
“SETUP MODE OFF” appears on the display and the unit exits Setup Mode.
24
AV-R610 XAC ENG-1
5/5/06 14:4212:0
Page 25
Setting DRC (Dynamic Range Compression)
You can use this function to enjoy Dolby Digital sound when watching movies at low volume at night.
√
REMOTE CONTROL
Press DRC button.
• Each time you press this button, DRC : STD ➝ DRC : MAX ➝ DRC : MIN
will be selected in turn.
OPERATION
MAIN UNIT
SETUP button.
1 Press
“SETUP MODE” appears on the display and enters into Setup Mode.
2 Press FUNCTION button 4 times.
•
• “DRC SETUP” appears on the display.
SURROUND button.
3 Press
“DRC : STD” appears on the display .
4 Press SELECT( , ) button to set DRC.
•
• Each time you press this button, DRC : STD ➝ DRC : MAX ➝ DRC : MIN
will be selected in turn.
To Exit Setup Mode
• Wait for about 5 seconds or press SETUP button.
“SETUP MODE OFF” appears on the display and the unit exits Setup Mode.
Setting DRC
• STD : Sets DRC effect to standard.
• MAX : Sets DRC effect to maximum.
• MIN : Sets DRC effect to minimum.
25
AV-R610 XAC ENG-1
5/5/06 14:4212:0
Page 26
Test Tone
Use test tone to check the speaker connection status or level.
To Automatically Output Test Tone
√
REMOTE CONTROL
Press TEST TONE button.
• Test signal will be automatically output as follows; F.L ➝ CEN ➝ F.R ➝ S.R
➝ S.L ➝ S.W.
• During test tone output, press …† button to adjust the speaker output level
from -10 to +10 dB by 1 step.
To Stop Test Tone
• Press TEST TONE button again.
√
MAIN UNIT
SETUP button.
1 Press
“SETUP MODE” appears on the display and enters into Setup Mode.
2 Press FUNCTION button 5 times.
“TEST-T AUTO” appears in the display.
3 Press SURROUND button.
•
•
• Test signal will be automatically output as follows; F.L ➝ CEN ➝ F.R ➝
S.R ➝ S.L ➝ S.W .
• During test signal output, press SELECT (
,
) button to adjust the speaker
output level from -10 to +10 dB by 1 step.
To Stop Test Tone
Press SETUP button 1 time.
• “SETUP MODE OFF” appears on the display and test tone stops.
26
AV-R610 XAC ENG-1
5/5/06 14:4212:0
Page 27
To Manually Output Test Tone
√
OPERATION
MAIN UNIT
SETUP button.
1 Press
“SETUP MODE” appears on the display and the unit enters into Setup Mode.
2 Press FUNCTION button 6 times.
•
• “TEST-T MANU” appears in the display.
3 Press SURROUND button.
• Each time you press this button, F.L ➝ CEN ➝ F.R ➝ S.R ➝ S.L ➝ S.W will
be selected in turn.
4 Press SELECT(
,
) button to set the test tone as you
want.
• You can adjust the speaker output level from -10 to +10dB by 1 step.
• The sound gets quieter at -10dB and louder at +10dB.
To Stop Test Tone
Press SETUP button 1 time.
• “SETUP MODE OFF” appears on the display and test signal stops.
Test Tone Output
• F.L (Front-Left) : -10 ~ +10dB
• CEN (Center) : -10 ~ +10dB
• F.R (Front-Right) : -10 ~ +10dB
• S.R (Surround-Right) : -10 ~ +10dB
• S.L (Surround-Left): -10 ~ +10dB
• S.W (Subwoofer): -10 ~ +10dB
27
AV-R610 XAC ENG-1
5/5/06 14:4212:0
Page 28
Setting Speaker Level
You can set the balance and level of speakers
√
Remote Control
SPK LEVEL button to select the speaker you want.
1 Press
Each time you press this button, F.L ➝ CEN ➝ F.R ➝ S.R ➝ S.L ➝ S.W ➝
•
SPK LVL OFF will be selected in turn.
…† button to set the speaker level you want.
2 Press
You can adjust it from -10 to +10dB by 1 step.
•
• The sound gets quieter at -10dB and louder at +10dB.
• Default setting value is 00dB.
To Exit Setup Mode
• Wait for about 5 seconds or press SPK LEVEL button on the remote control to select
SPK LVL OFF.
28
AV-R610 XAC ENG-1
5/5/06 14:4212:0
Page 29
MAIN UNIT
1 Press SETUP button.
• “SETUP MODE” appears on the display and enters into Setup Mode.
OPERATION
FUNCTION button 8 times.
2 Press
“LEVEL SETUP” appears on the display.
•
SURROUND button.
3 Press
Each time you press this button, F.L ➝ CEN ➝ F.R ➝ S.R ➝ S.L ➝ S.W
•
will be selected in turn.
4 Press SELECT(
,
) button to set to the speaker level
you want.
• You can adjust it from -10 to +10dB by 1 step.
• The sound gets smaller at -10dB and louder at +10dB.
• Default setting value is 00dB
To Exit Setup Mode
• Wait for about 5 seconds or press SETUP button.
“SETUP MODE OFF” appears on the display and exits Setup Menu.
Setting Speaker Level
• F.L (Front-Left) : -10 ~ +10dB
• CEN (Center) : -10 ~ +10dB
• F.R (Front-Right) : -10 ~ +10dB
• S.R (Surround-Right) : -10 ~ +10dB
• S.L (Surround-Left): -10 ~ +10dB
• S.W (Subwoofer): -10 ~ +10dB
29
AV-R610 XAC ENG-1
5/5/06 14:4212:0
Page 30
Dolby Pro Logic ll Mode
This mode provides 5.1 channel sound from 2 channel sources
REMOTE CONTROL
Press
MODE button.
• Each time you press this button, CINEMA ➝ MATRIX ➝ GAME
➝ PROLOGIC ➝ MUSIC will be selected in turn.
To Exit Setup Mode
• Wait for about 5 seconds.
30
AV-R610 XAC ENG-1
5/5/06 14:4212:0
Page 31
MAIN UNIT
1 Press SURROUND button to select “DPL ll” Mode.
• Each time you press this button, DPL ll ➝ SFE ➝ STEREO will be selected
in turn.
,
OPERATION
2 Press SELECT(
) button.
) button, CINEMA ➝ MATRIX ➝
GAME ➝PROLOGIC ➝ MUSIC will be selected in turn.
• Each time you press SELECT (
) button, MUSIC ➝ PROLOGIC ➝
GAME ➝ MATRIX ➝ CINEMA will be selected in turn.
• Each time you press SELECT (
To Exit Setup Mode
• Wait for about 5 seconds.
Dolby Pro Logic ll Mode
• MUSIC : Provides 5.1 Channel Surround sound to digital, analog
or existing stereo sources such as CD, TAPE, FM, TV and
Stereo VCR.
• CINEMA : Adds realism to the movie soundtrack.
• MATRIX : You will hear 5.1 Channel Surround sound.
• GAME : Enhances the excitement of the game's sound.
• PROLOGIC : You will experience a surround effect with just the
front left and right speakers.
• You cannot use Dolby Pro Logic ll Mode for multi channel
signals such as Dolby Digital and DTS.
• Pro Logic works only for PCM audio signals with sampling
frequencies of 32KHz, 44KHz or 48KHz.
• Sound will not be output from rear center speaker if PCM
audio signal is mono.
31
AV-R610 XAC ENG-1
5/5/06 14:4212:0
Page 32
Dolby Pro Logic ll Effect
This function works only in Dolby PRO LOGIC II MUSIC Mode.
REMOTE CONTROL
MODE button to select ‘MUSIC’ Mode.
1 Press
EFFECT button.
2 Press
Each time you press this button, C-WIDTH ➝ DIMENSION ➝ PANORAMA ➝
•
DPL ll EFT OFF will be selected in turn.
…† button to select Dolby Pro Logic II effect you
3 Press
want.
• C-WIDTH: You can set from 0 to 7.
• DIMENSION: You can set from -7 to +7.
• PANORAMA: You can Set it ON or OFF.
To Exit Setup Mode
• Wait for about 5 seconds or press
control to select DLP ll EFT OFF.
32
Effect button of remote
AV-R610 XAC ENG-1
5/5/06 14:4212:0
Page 33
MAIN UNIT
SETUP button.
1 Press
“SETUP MODE” appears on the display and enters into Setup Mode.
•
OPERATION
FUNCTION button 10 times.
2 Press
“DPL ll MODE”appears on the display.
•
SURROUND button.
3 Press
Each time you press this button, C-WIDTH ➝ DIMENSION ➝
•
PANORAMA will be selected in turn.
4 Press SELECT(
, ) button to select Dolby Pro
Logic ll effect you want.
To Exit Setup Mode
• Wait for about 5 seconds or press SETUP button.
“SETUP MODE OFF” appears on the display and exits Setup Mode.
Dolby Pro Logic llx Effect
• C-WIDTH : This sets the width of the center image. The higher the setting, the less
sound comes from the center speaker.
• DIMENSION : Incrementally adjusts the sound field (DSP)from the front or rear.
• PANORAMA : This mode extends the front stereo image to include the surround
speakers for an exciting "wraparound" effect with side wall imaging.
33
AV-R610 XAC ENG-1
5/5/06 14:4212:0
Page 34
SFE Mode
Refer to the unique sound existing at specific place and you can feel live sound as if you are listening at
actual site.
REMOTE CONTROL
Press SFE MODE button.
• Each time you press this button, HALL ➝ THEATER ➝ ARENA ➝ CLUB ➝
DOME ➝ STADIUM ➝ CHURCH will be selected in turn.
To Exit Setup Mode
• Wait for about 5 seconds.
34
AV-R610 XAC ENG-1
5/5/06 14:4212:0
Page 35
MAIN UNIT
SURROUND button to select ‘SFE’ Mode.
1 Press
Each time you press this button, DPL II ➝ SFE ➝ STEREO will be selected
•
in turn.
•
CLUB ➝ DOME ➝ STADIUM ➝ CHURCH will be selected in turn
) button, CHURCH ➝ STADIUM ➝
DOME ➝ CLUB ➝ ARENA ➝ THEATER ➝ HALL will be selected in turn.
• Each time you press Select (
To Exit Setup Mode
• Wait for about 5 seconds.
35
OPERATION
SELECT( , ) button.
2 Press
Each time you press Select (
) button, HALL ➝ THEATER ➝ ARENA ➝
AV-R610 XAC ENG-1
5/5/06 14:4212:0
Page 36
Stereo Mode
You can select this mode when you listen to sound through the Front Left and Right speakers and subwoofer.
REMOTE CONTROL
Press STEREO button.
Press SURROUND button to select ‘STEREO’.
• “STEREO” appears in the display and Stereo Mode is
• Each time you press this button, DPL ll ➝ SFE ➝ STEREO
selected.
will be selected in turn.
To Exit Setup Mode
To Exit Setup Mode
• Wait for about 5 seconds.
• Wait for about 5 seconds.
• When PCM and Analog Stereo signals are input, the
left and right channels are played back in Stereo Mode.
36
MAIN UNIT
AV-R610 XAC ENG-1
5/5/06 14:4212:0
Page 37
For Surround Mode and Input Signal
o = active, – = inactive
Output Channel
Surround Mode
DOLBY
(MUSIC,
CINEMA,
MATRIX,
GAME,
PROLOGIC)
Input Signal
Decoding
Display Information
SL
Sub
SR Woofer
L/R
C
O
O
O
Display Signal Format
Channel Status
Dolby D Surr. EX
Dolby Digital 5.1
O
DIGITAL
L, C, R, SL, SR, SW
Dolby D (5.1ch)
Dolby Digital 5.1
O
O
O
O
DIGITAL
L, C, R, SL, SR, SW
Dolby D (2ch)
Pro Logic II
O
O
O
O
DIGITAL
L, C, R, SL, SR, SW
Dolby D (2ch Surr)
Pro Logic II
O
O
O
O
DIGITAL
L, C, R, SL, SR, SW
L.PCM (Audio)
Pro Logic II
O
O
O
O
L.PCM
L, C, R, SL, SR, SW
Analogique
Pro Logic II
O
O
O
O
ANALOG
L, C, R, SL, SR, SW
DTS-ES
DTS 5.1
O
O
O
O
DTS
L, C, R, SL, SR, SW
DTS 96/24
DTS 5.1
O
O
O
O
DTS
L, C, R, SL, SR, SW
DTS (5.1)
DTS 5.1
O
O
O
O
DTS
L, C, R, SL, SR, SW
L.PCM (Audio)
Neo:6
O
O
O
-
L.PCM
L, R
Dolby D (2ch)
DD+ SFE
O
O
O
O
DIGITAL
L, C, R, SL, SR, SW
Dolby D (2ch Surr)
DD+ SFE
O
O
O
O
DIGITAL
L, C, R, SL, SR, SW
L.PCM (Audio)
SFE
O
O
O
O
L.PCM
L, C, R, SL, SR, SW
Analogique
SFE
O
O
O
O
ANALOG
L, C, R, SL, SR, SW
Dolby D (2ch)
DD
O
-
-
-
DIGITAL
L, R, SW
Dolby D (2ch Surr)
DD
O
-
-
-
DIGITAL
L, R, SW
L.PCM (Audio)
Stereo
O
-
-
-
L.PCM
L, R, SW
L.PCM 96KHz
Stereo
O
-
-
-
L.PCM
L, R, SW
Analogique
Stereo
O
-
-
-
ANALOG
L, R, SW
DTS
OPERATION
SFE
STEREO
L/R : Front Speaker (Left/Right) C : Center Speaker SL/SR : Rear Speaker (Left/Right) SW : Subwoofer
• Channel status display are dependent on “Speaker Configuration”.
• SFE Mode works 2ch signal.
37
AV-R610 XAC ENG-1
5/5/06 14:4212:0
Page 38
Listening to Radio
You can listen to the chosen band (FM, AM broadcast stations) by using either the automatic or manual
tuning operation.
REMOTE CONTROL
MAIN UNIT
1 Press TUNER button.
1 Press FUNCTION button to select
• Each time you press this button, FM ➝ AM will be
repetitively selected.
2 Select frequency.
• Automatic Tuning 1
:
1) Press TUNER MODE button to select PRESET.
2) Press TUNING/CH ( , ) button to select the preset
frequency.
• Automatic Tuning 2 :
1) Press TUNER MODE button to select MANUAL
2) Press and hold TUNING/CH ( , ) button to
automatically tune in frequency.
• Manual Tuning :
1) Press TUNER MODE button to select MANUAL.
2) Press TUNING/CH ( , ) button briefly to increase or
decrease frequency by step by step.
To Listen to Mono/Stereo
Press MO/ST button on the remote.
• Each time you press this button, STEREO, MONO
will be selected in turn.
• If you select MONO in the area with weak reception,
it will help to reduce noise.
• This function works only with the Remote Control.
38
FM or AM.
2 Select the frequency.
• Automatic Tuning :
Press and hold TUNING( , ) button to
automatically tune in frequency.
• Manual Tuning :
Press TUNING( , ) button briefly to
increase or decrease the frequency step by step.
How to select MAIN, UNIT, PRESET,
MANUAL
1. Press the SETUP button.
2. Press the FUNCTION button 9 times.
• “TUNER SETUP” appears in the display.
3. Press the SURROUND button.
4. SELECT ( , ) button to select MANUAL
or PRESET.
AV-R610 XAC ENG-1
5/5/06 14:4212:0
Page 39
Presetting Radio Stations
You can preset up to 30 FM and AM stations.
REMOTE CONTROL
Ex) If you preset FM 89.10 station in 2ch
TUNER button.
1 Press
Each time you press this button, FM ➝ AM will be selected in turn.
•
2 Press Select button and then TUNING MODE button
to select 89.10.
• Refer to step 2, page 38, to tune in automatically and manually.
TUNER MEMORY button.
3 Press
Tuner number will blink on the display.
•
4 Press TUNING/CH(
,
) button to select preset 2.
• You can select from presets 1 to 30.
RADIO OPERATION
TUNER MEMORY button.
5 Press
Tuner number will disappear and station 89.1 will be saved in preset 2.
•
6 To preset other stations, repeat steps 2 to 5.
To Listen to Preset Station
• Press TUNING MODE button of the remote control to select the PRESET and press
TUNING/CH (
,
) button.
39
AV-R610 XAC ENG-1
5/5/06 14:4212:0
Page 40
Convenient Functions
Sleep Timer Function
You can set the time that this unit will shut itself off.
REMOTE CONTROL
Press the SLEEP button.
• SLEEP : OFF ➝ 15 ➝ 30 ➝ 45 ➝ 60 ➝ 90 ➝ 120MIN will be selected in turn.
To Check Sleep Timer
Press SLEEP button.
• The remaining time before this unit will shut itself off is shown on the display.
• Pressing the button again changes the sleep time from what you have set earlier.
To Cancel Sleep Timer
• Press SLEEP button until SLEEP : OFF appears on the display.
Mute Function
This function is useful when answering a doorbell or telephone call.
REMOTE CONTROL
Press the MUTE button.
• MUTE appears on the display.
To Output Sound Again
Press MUTE button again.
• MUTE will disappear and sound will Output.
• SLEEP, Mute and Adjust Display function can only be
operated with the remote control.
40
AV-R610 XAC ENG-1
5/5/06 14:4212:0
Page 41
Reset Function
REMOTE CONTROL
1
2
3
Press the MUTE button.
• MUTE appears on the display.
Press “0” button five times and then
press ENTER button.
Press …† buttons to select “YES”.
• The unit will turn automatically back on in 5 seconds.
Caution!
• Using the RESET function will erase all stored settings.
• Do not use this unless necessary.
Adjust the Display
You can adjust the brightness of the display.
REMOTE CONTROL
Press the DIMMER button.
• Each time you press this, the brightness of the display will be adjusted.
Using Headphone
Use headphones (not supplied) for private listening pleasure.
MISCELLANENOUS
Connect the headphone to the headphone jack and listen
to music.
• Do not turn the volume up too high when you use headphones as It
may damage your hearing.
41
AV-R610 XAC ENG-1
5/5/06 14:4212:0
Page 42
Operating your TV with the Remote Control
1
Press TV button to set the remote
to TV mode.
2
Press POWER button to turn
on the TV.
3
Point the remote control toward the TV.
4
While holding down POWER button,
enter the code corresponding to your
brand of TV.
• If the code matches the TV's code, the TV will be turned off.
• If there is more than one code listed for your TV in the table, enter
one at a time to determine which code works.
5
If TV is turned on or off when you press the
power button of the remote control, the
setting is completed.
• You can use the TV POWER, VOLUME, CHANNEL, MENU and
Numeric buttons (0~9).
• The remote control may not work on some brands of TVs. Also, some operation
may not be possible depending on your brand of TV.
• The remote control will work with Samsung TVs by default.
42
AV-R610 XAC ENG-1
5/5/06 14:4212:0
Page 43
TV Brand Code List
Brand
ADMIRAL(M.WARDS)
A MARK
ANAM
AOC
BELL & HOWELL(M.WARDS)
BROCSONIC
CANDLE
CETRONIC
CITIZEN
CINEMA
CLASSIC
CONCERTO
CONTEC
CORONADO
CRAIG
CROSLEX
CROWN
CURTISMATES
CXC
DAEWOO
DAYTRON
DYNASTY
EMERSON
HALL MARK
HITACHI
INKEL
JC PENNY
JVC
KTV
KEC
KMC
LG(GOLDSTAR)
Brand
LUXMAN
LXI(SEARS)
MAGNAVOX
MARANTZ
MATSUI
MGA
MITSUBISHI/MGA
MTC
NEC
NIKEI
ONKING
ONWA
PANASONIC
PENNEY
PHILCO
PHILIPS
PIONEER
PORTLAND
PROTON
QUASAR
RADIO SHACK
RCA/PROSCAN
REALISTIC
SAMPO
SAMSUNG
SANYO
SCOTT
SEARS
SHARP
SIGNATURE 2000(M.WARDS)
SONY
SOUNDESIGN
SPECTRICON
SSS
Code Number
018
019, 054, 056, 059, 060,
062, 063, 065, 071
015, 017, 018, 048, 054,
059, 060, 062, 072, 089
040, 054
054
018, 040
018, 040, 054, 059, 060,
075, 101
018
018, 019, 020, 040, 059,
060
003
003
003
006, 007, 008, 009, 054,
066, 067, 073, 074
018
003, 015, 017, 018, 048,
054, 059, 062, 069, 090
015, 017, 018, 040, 048
054, 062, 072, 112, 114,
117, 118
063, 066, 080, 091
015, 018, 059
040
006, 066, 067
017, 048, 056, 060, 061,
075
018, 059, 067, 076, 077
078, 092, 093, 094
003, 019
040
000, 015, 016, 017, 040,
043, 046, 047, 048, 049,
054, 059, 060, 098
019, 061, 065, 101, 102,
103, 104
003, 040, 060, 061
015, 018, 019
015, 057, 064, 101, 105,
106, 115
057, 058
050, 051, 052, 053, 055,
101
003, 040
001
018
Brand
SYLVANIA
SYMPHONIC
TATUNG
TECHWOOD
TEKNIKA
TMK
TOSHIBA
VIDTECH
VIDECH
WARDS
YAMAHA
YORK
YUPITERU
ZENITH
ZONDA
DONGYANG
LOWE
FINLUX
YOKO
LOEWE OPTA
PHONOLA
RADIOLA
SCHNEIDER
AKAI
GRUNDIG
BLAUPUNKT
SIEMENS
CGE
IMPERIAL
MIVAR
SABA
BANG&OLUFSEN
BRIONVEGA
FORMENTI
METZ
WEGA
RADIOMARELLI
SINGER
SINUDYNE
TELEFUNKEN
Code Number
018, 040, 048, 054, 059,
060, 062
061, 095, 096
006
018
003, 015, 018, 025
018, 040
019, 057, 063, 071, 101
107, 109, 110, 111, 113
018
059, 060, 069
015, 017, 018, 040, 048,
054, 060, 064
018
040
003
058, 079
001
003, 054
054
054, 109, 114
054
054, 114
054, 112, 114
054, 112
054
103
108, 109, 113, 119, 120,
121
108
108
113
113
113
114
114
114
114
114
114
114
114
114
116
MISCELLANENOUS
FISHER
FUNAI
FUTURETECH
GENERAL ELECTRIC(GE)
Code Number
056, 057, 058
001, 015
001, 002, 003, 004,005,
006, 007, 008, 009, 010,
011, 012, 013, 014
001, 018, 040, 048
057, 058, 081
059, 060
018
003
003, 018, 025
097
003
018
046
015
003, 005, 061, 082, 083,
084
062
003
059, 061, 063
003
002, 003, 004, 015,016,
017, 018, 019, 020, 021,
022, 023, 024, 025, 026,
027, 028, 029, 030, 032,
034, 035, 036, 040, 048,
059, 090, 099, 100
040
003
003, 015, 040, 046, 059,
061, 064, 082, 083, 084,
085
019, 065, 103
003
003
006, 040, 056, 059, 066,
067, 068
040
015, 018, 050, 059, 069
045
056, 059, 067, 086
070
059, 061, 087, 088
003, 015, 040
015
001, 015, 016, 017, 037,
038, 039, 040, 041, 042,
043, 044, 054, 086
43
AV-R610 XAC ENG-1
5/5/06 14:4212:0
Page 44
Operating your DVD (VCR) with Remote Control
1
Press DVD button to set the remote to
DVD mode.
2
Press POWER button to turn on the DVD
(VCR).
3
Point the remote control toward the DVD
(VCR).
4
While holding down POWER button, enter
the code corresponding to your brand of
DVD (VCR).
• If you operate VCR, press VCR button to set the remote to VCR mode.
• If the code matches the DVD (VCR)'s code, the DVD (VCR)
will be turned off.
• If there is more than one code listed for your DVD (VCR) in
the table, enter one at a time to determine which code works.
5
If DVD (VCR) is turned on or off when you
press the power button of the remote
controller, the setting is completed.
• You can use DVD (VCR) POWER, VOLUME, PLAY, PAUSE,
STOP, SKIP, MENU and Numeric button (0~9).
• The remote control may not work on some brands of DVD (VCR)s.
Also, some operations may not be possible depending on your brand
of DVD (VCR).
• The remote control will work with Samsung DVDs (VCRs) by default.
44
AV-R610 XAC ENG-1
5/5/06 14:4212:0
Page 45
VCR Brand Code List
Brand
ADMIRAL(M.WARDS)
AWIA
AKAI
ANAM
AOC
AUDIO DYNAMIC
BELL & HOWELL(M.WARDS)
BROKSONIC
CANON
CAPEHART
CITIZEN
CRAIG
CRITERION
CURTIS MATHES
DAEWOO
DAYTRON
DBX
EMERSON
FISHER
FUNAI
GENERAL ELECTRIC(GE)
GO VIDEO
HARMAN KARDON
HITACHI
JVC
KENWOOD
LG(GOLDSTAR)
LXI(SEARS)
MAGIN
MAGNAVOX
MARANTZ
MARTA
043, 106
044, 045, 046
088, 089, 090
001, 002, 003, 004, 005,
033
091
019, 047, 092
048, 093
092, 094, 095
001, 033, 049, 091
011
050
050, 072, 096
051
001, 031, 032, 033, 044,
091
006, 007, 008, 009, 010,
011, 012, 013, 014, 015,
016, 017, 018, 046, 051,
091
011
019, 047, 052, 092
025, 031, 032, 044, 046,
094, 095, 097, 098, 099
009, 048, 053, 054, 055,
100
044
001, 031, 032, 033, 056,
091
059, 060, 061
019
020, 021, 049, 054, 062,
100
051
001, 033, 049, 091
001, 033
025
047, 048, 052, 062, 091,
092
001, 033, 047, 052, 063,
064, 065, 092
047, 050, 052, 092
019, 020, 021, 022, 023,
024, 025, 026, 027, 028,
029, 030, 050
020, 025, 044, 048, 050,
053, 054, 055, 062, 100
072
001, 031, 032, 033, 049,
066, 067, 091
001, 019, 033, 047, 052,
092, 110
025, 050
Brand
MEI
MEMOREX
MINOLTA
MITSUBISHI/MGA
MTC
MULTITECH
NEC
OLYMPIC
OPTIMUS
ORION
PANASONIC
PENNEY
PENTAX
PHILCO
PHILIPS
PILOT
PIONEER
PORTLAND
QUASAR
RICO
RCA/PROSCAN
REALISTIC
044, 048, 054, 091,
SAMSUNG
SANYO
SANSUI
SCOTT
SEARS
SHARP
SINGER
SIGNATURE 2000(M.WARDS)
SHINTOM
SONY
STS
SYLVANIA
SYMPHONIC
TANDY
Code Number
001, 033
001, 025, 033, 054, 091,
100
020, 021, 062
068, 069, 070, 101, 102
072
044, 057, 069
019, 047, 052, 057, 092
049, 091
101
103
001, 004, 033, 049, 067,
091, 107
019, 020, 072
001, 020, 021, 033, 062
001, 033, 046, 049, 091,
094
001, 030, 033, 049, 050,
066, 091
025
049
011
001, 033, 049, 067, 091,
107, 108
036
001, 020, 021, 031, 032,
033, 049, 051, 062, 066,
070, 091, 104
001, 009, 025, 033,
101, 105
000, 006, 031, 032, 057,
058, 071, 072, 073, 074,
075, 076, 077, 078, 079,
080, 081
008, 009, 046, 048, 050,
054, 058, 093, 100
092
006, 051, 054, 057, 069,
070, 100, 101
020, 021, 025
043, 105, 106
096
043, 044, 054, 100, 106
096
034, 035, 036, 037, 038,
039, 040, 041, 042,082,
083, 084, 085, 086
020
001, 033, 044, 049, 066,
091
044
009
Brand
TASHIRO
TATUNG
TEAC
TECHNICS
TEKNIKA
TOSHIBA
TOTEVISION
TAEKWANG
UNITECH
VECTOR RESEARCH
VIDEO CONCEPTS
VIDEOSONIC
WARDS
YAMAHA
ZENITH
Code Number
050
047, 052, 092
044, 047, 052, 092
001, 033, 049, 091
001, 025, 033
006, 051
025, 072
087
072
019
019
072
001, 020, 031, 032, 033,
043, 050, 054, 072, 100,
105, 106, 109
019, 047,048, 052, 092,
019, 047,048, 052, 092
DVD Brand Code List
Brand
DENON
DOONOON
DMTECH
FISHER
GE
HARMAN/KARDON
JVC
KENWOOD
LG
MAGNAVOX
MITSUBISHI
ONKYO
OPTIMUS
PANASONIC
PROSCAN
PHILIPS
PIONEER
RCA
SAMSUNG
SANYO
SONY
THETA DIGITAL
TOSHIBA
YAMAHA
ZENITH
TAEGWANG
PS2
X-BOX
APEX
MARANTZ
Code Number
003, 032
019
017
002
006
012
010, 013
008
001
004
005, 016
004, 014
011
021
006
004, 023
007, 011, 022, 025
006
000, 027
002
015, 020
011
004, 018
009, 033
004, 024
026
028
029
030
031
MISCELLANENOUS
HQ
INSTANT REPLAY
JCL
JCP
JC PENNY
Code Number
45
AV-R610 XAC ENG-1
5/5/06 14:4212:0
Page 46
Before Calling for Service
Check
Symptom
Remedy
Can't turn it on.
• Is the power code plugged into the outlet?
• Connect the power plug to the outlet.
It does not work when the
button is pressed.
• Is there static electricity in the air?
• Disconnect the power plug and connect it
again.
• Are the speaker and external
Sound is not produced.
component connected properly?
• Does the Mute function work?
• Is the volume set to minimum?
• Is the speaker setup selected to
NONE?
Picture does not appear when
the function is selected.
• Isn’t the external component connected
Remote controller does
not work.
• Are the batteries exhausted?
• Is the distance between remote
The sound from each
device is changed during
stereo playback.
Can't receive
control and main unit proper?
• Is the left/right speaker or left/right
input/output code connected
properly?
• Is AM or FM antenna connected
properly?
properly?
• Is S.SPK (Surround) set to NONE in
Speaker Setup?
• Is Surround Mode selected to Stereo?
There is no sound from
center speaker
• Adjust the volume.
• Refer to pages 20~21 to select LARGE,
SMALL or YES.
• Properly connect it.
• Replace with new batteries.
• Operate at close distance.
• Check the left/right channel and properly
connect it.
• Properly connect the antenna.
• If the input strength of antenna connector
is weak, install the FM antenna in a place
with good reception.
• Is the surround speaker connected
surround speaker.
• Press Mute button to cancel the function.
properly?
broadcasting.
There is no sound from
• Properly connect it.
• Refer to pages 10~11 to connect it properly.
• Refer to pages 20~21 to select LARGE or
SMALL.
• Refer to pages 30~37 to select other
Surround Mode.
• Is the center speaker connected properly?
• Refer to pages 10~11 to connect it properly.
• Is C.SPK (Center) selected to NONE in
• Refer to pages 20~21 to select LARGE or
Speaker Setup?
• Is the Surround Mode selected to Stereo?
SMALL.
• Refer to pages 30~37 to select other
Surround Modes.
46
AV-R610 XAC ENG-1
5/5/06 14:4212:0
Page 47
Symptom
Can't select Dolby Pro
Check
• Is the input signal selected properly?
Logic ll Mode.
There is no sound when
playing DTS encoded DVD
and CD.
Remedy
• Select 2 channel Dolby Digital, PCM, and
Analog input signal.
• Is analog input selected?
• Check whether digital external component
is properly connected and refer to page 22
to select the digital input.
MISCELLANENOUS
Product Protection Function
Heat Protection
• Protection function works if the main unit is overheated or power
transformer is overheated.
"
" appears in the display when this function
works.
- If speaker terminal is shorted
- If speaker cord is shorted
If there is no problem when you turn it on again after turning it
off, PROTECTION mark will disappear on the display and the
unit will work properly.
• If PROTECTION appears on the display,
check whether speaker terminal is shorted
and then turn on the device.
47
Specifications
GENERAL
FM TUNER
AM TUNER
AMPLIFIER
FREQUENCY
RESPONSE
VIDEO
OUTPUT
S
P
E
A
K
E
R
S
Power Supply
Standby Power Consumption
Power Consumption
Weight
Dimensions (W x H x D)
Operating Temperature Range
Operating Humidity Range
Frequency Response
Usable Sensitivity
S/N Ratio
Distortion
Stereo Separation
Tuner Output Level
Frequency Response
S/N Ratio
Usable Sensitivity
Distortion
Rated Output
Front Speaker(Left+Right)
Center Speaker
Surround Speaker(Left+Right)
Subwoofer
Input Sensitivity/Impedance
S/N Ratio(Analog Input)
Separation(1KHz)
Analog Input
Digital Input/96KHz PCM
TV Format
Input Level/Impedance
Output Level/Impedance
Video Frequency Response
Component Video Frequency Response
S/N Ratio
Speaker system
Impedance
Rated input
Maximum input
Dimensions (W x H x D)
Weight
Front / Surround
4Ω x 4
100W
200W
3.5 x 6.0 x 3.5 inches
1.3 Ibs/1.1Ibs
120V, 60 Hz
0.9W
95W
9.25Ibs
16.9 x 2.6 x 13.7 inches
41°F ~ 95°F
10%~75%
87.5~108.0MHz
12dBf
MONO/STEREO 55/55dB
MONO/STEREO 0.3/0.8%
30dB
1KHz, 75KHz Dev
520~1720KHz
40dB
60dBµV/m(Loop Antenna)
2% (MOD:80%)
20Hz~20KHz/THD = 10%
4 Ω 100W/CH
4 Ω 100W/CH
4 Ω 100W/CH
4 Ω 100W/CH
450mV/47k Ω
80dB
60dB
20Hz~20KHz(±3dB)
20Hz ~44KHz(±3dB)
NTSC/PAL
1Vp-p/75Ω
1Vp-p/75Ω
5Hz to 10KHz(-3dB)
5Hz to 40KHz(-3dB)
60dB
Center
Subwoofer speaker
4Ω
4Ω
100W
100W
200W
200W
7.9 x 3.5 x 3.6 inches 6.9 x 12.6 x 15.0 inches
1.4 Ibs
11.5 Ibs
❈ S/N ratio, distortion, separation and usable sensitivity are based on measurement using AES-17 filter.
48
AV-R610 XAC ENG-1
5/5/06 14:4212:0
Page 49
Samsung Limited Warranty
Samsung Electronics Canada Inc. (SECA), warrants that this product is
free from defective material and workmanship.
SECA further warrants that if this product fails to operate properly within the
specified warranty period and the failure is due to improper workmanship or
defective material SECA will repair or replace the product at its option.
All warranty repairs must be performed by a SECA authorized service
centre. (The name and address of the location nearest you can be obtained by
calling toll free 1-800-726-7864 or visiting our web site at
www.samsung.ca)
Labour
one (1) year (carry-in)
Parts
one (1) year
On carry-in models, transportation to and from the service centre is the
customer’s responsibility.
The original dated sales receipt must be retained by the customer and is the
only acceptable proof of purchase. It must be presented to the authorized
service centre at the time service is requested.
Exclusions
MISCELLANENOUS
This warranty does not cover damage due to accident, fire flood and/or other
acts of God; misuse, incorrect line voltage, improper installation, improper or
unauthorized repairs, commercial use, or damage that occurs in shipping.
Exterior and interior finish, lamps and glass are not covered under this
warranty. Customer adjustments which are explained in the instruction
manual are not covered under the terms of this warranty.
This warranty will automatically be voided for any unit found with a
missing or altered serial number. This warranty is valid only on products
purchased and used in Canada.
49