Emerson Liebert Deluxe System/3 DE Installation manual

Precision Cooling
For Business-Critical Continuity
Liebert Deluxe System/3™ - DX
Installation Manual - 50 and 60 Hz, 6-30 Ton DX Systems (DH/DE/VH/VE)
TABLE OF CONTENTS
PRODUCT MODEL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . V
1.0
INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
1.1
System Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1.1.1
1.1.2
1.1.3
1.1.4
Compressorized Two-Step Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Compressorized Four-Step Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
GLYCOOL™ (Chilled Glycol Cooling) Systems. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Dual Source Cooling Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1
1
2
2
2.0
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
2.1
Room Preparation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2.2
Location Considerations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2.3
Unit Dimensions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2.4
Piping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
2.4.1
2.4.2
Drain Line . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Piping Considerations for Raised-Floor Applications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
2.5
Electrical Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
2.6
Air Distribution Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
2.6.1
2.6.2
2.6.3
2.6.4
2.6.5
Raised-Floor Air Flow Distribution Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Upflow Systems Additional Installation Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ducted Application Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Plenum Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Filter Box Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
15
15
16
16
16
3.0
AIR COOLED MODELS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
3.1
Condenser Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
3.1.1
3.1.2
3.2
Outdoor Prop Fan Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Indoor Piggyback Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Electrical Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
3.2.1
3.2.2
3.2.3
High Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Low Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Lee-Temp/Flood Back Head Pressure Control Condensers (Standard on Piggyback Models) 19
3.3
Refrigerant Piping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
3.4
Fan Speed Control Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
3.4.1
3.4.2
3.4.3
3.5
Lee-Temp/Flood Back Head Pressure Control Systems. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
3.5.1
3.5.2
3.5.3
3.5.4
3.5.5
4.0
Materials Supplied . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Dehydration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Charging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Piping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Materials Supplied . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Dehydration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Charging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Refrigerant Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
33
33
33
34
34
GLYCOL COOLED/GLYCOOL™ MODELS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
i
4.1
Drycooler Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
4.1.1
4.1.2
Outdoor Prop Fan Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Indoor Piggyback Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
4.2
Drycooler Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
4.3
Electrical Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
4.3.1
4.3.2
4.3.3
High Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Low Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Pump And Drycooler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
4.4
Glycol Piping. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
4.5
Preparation of Glycol Solutions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
5.0
WATER COOLED MODELS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48
5.1
Piping Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
5.2
Condenser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
5.3
Water Regulating Valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
5.3.1
5.3.2
Testing Valve Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Manual Flushing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
ii
FIGURES
Figure 1
Figure 2
Figure 3
Figure 4
Figure 5
Figure 6
Figure 7
Figure 8
Figure 9
Figure 10
Figure 11
Figure 12
Figure 13
Figure 14
Figure 15
Figure 16
Figure 17
Figure 18
Figure 19
Figure 20
Figure 21
Figure 22
Figure 23
Figure 24
Figure 25
Figure 26
Figure 27
Figure 28
Figure 29
Figure 30
Figure 31
Figure 32
Figure 33
Figure 34
Downflow (DH and DE models) cabinet and floor planning dimensional data . . . . . . . . . . . . . . . . 4
Upflow 6, 8 and 10 ton (VH and VE models) cabinet and floor planning dimensional data . . . . . 6
Upflow 6, 8 and 10 ton (VH and VE models) blower duct and deck dimensional data . . . . . . . . . . 7
Upflow 15, 20 and 22 ton (VH and VE models) cabinet and floor planning dimensional data . . . 8
Upflow 15, 20 and 22 ton (VH and VE models) blower duct and deck dimensional data . . . . . . . . 9
Upflow 30 ton (VH and VE models) cabinet and floor planning dimensional data. . . . . . . . . . . . 10
Upflow 30 ton (VH and VE models) blower duct and deck dimensional data . . . . . . . . . . . . . . . . 11
Electrical connection details. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Electrical field connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Ducting configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Plenum dimensional data for 6 - 22 ton models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Plenum dimensional data for 30 ton models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Piping: Fan speed control condensers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Piping: Lee-Temp control condensers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Downflow air cooled (DH) piping connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Upflow air cooled (VH) piping connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Outdoor air cooled 1-4 fan condenser cabinet and anchor dimensional data . . . . . . . . . . . . . . . . 25
Outdoor air cooled 6 and 8 fan condenser cabinet and anchor dimensional data . . . . . . . . . . . . . 27
Air cooled model general arrangement diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Piggyback condenser cabinet and floor planning dimensional data . . . . . . . . . . . . . . . . . . . . . . . 29
Piggyback condenser piping connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Lee-Temp control condenser. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Lee-Temp control typical general arrangement diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Downflow glycol cooled (DH) piping connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Upflow glycol cooled (VH) piping connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Downflow GLYCOOL™ cooled (DE) piping connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Upflow GLYCOOL™ cooled (VE) piping connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
1-4 fan drycooler cabinet and anchor dimensional data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
6- and 8-fan drycooler cabinet and anchor dimensional data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Glycol general arrangement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
GLYCOOL™ general arrangement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Water cooled general arrangement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Downflow water cooled (DH) piping connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Upflow water cooled (VH) piping connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
iii
TABLES
Table i
Table ii
Table 1
Table 2
Table 3
Table 4
Table 5
Table 6
Table 7
Table 8
Table 9
Table 10
Table 11
Table 12
Table 13
Table 14
Table 15
Table 16
Table 17
Table 18
Table 19
Table 20
Table 21
Table 22
Table 23
Table 24
Table 25
Table 26
Table 27
Table 28
Table 29
Table 30
Table 31
Table 32
Table 33
Table 34
Table 35
Table 36
Table 37
Model number designation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v
Unit weights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vi
Downflow (DH and DE models) dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Upflow 6, 8 and 10 ton (VH and VE models) blower duct and deck dimensional data . . . . . . . . . . 7
Upflow 15, 20 and 22 ton (VH and VE models) blower duct and deck dimensional data . . . . . . . . 9
Upflow 15, 20 and 22 ton (VH and VE models) blower duct and deck dimensional data . . . . . . . 11
Recommended free area ft2 (m2 for grilles or perforated panels at output velocities of 550
and 600 fpm (2.8 and 3.1 m/s) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Plenum dimensional data for 6 - 22 ton models, in. (mm) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Plenum dimensional data for 30 ton models in. (mm) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Recommended line sizes – O.D. copper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Fan speed control condenser piping connection sizes - Cu OD. . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Lee-Temp control condenser piping connection sizes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Downflow air cooled (DH) piping connection sizes, inches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Factory provided piping connection sizes, inches, upflow air cooled (VH). . . . . . . . . . . . . . . . . . . 24
Outdoor air cooled 1-4 fan condenser physical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Outdoor air cooled 6 and 8 fan condenser physical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Refrigerant control settings psi (kPa) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Piggyback condenser dimensional data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Piggyback condenser piping connection dimensional data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Piggyback condenser approximate refrigerant charges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Liquid line charge lb/10 ft. (kg/.3m) R–22 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Refrigerant control settings for air cooled units psi (kPa) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Indoor unit approximate refrigerant charge lb (kg.) R–22 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Outdoor condenser approximate refrigerant charge lb (kg) per circuit . . . . . . . . . . . . . . . . . . . . . 32
Glycol concentration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Refrigerant control settings for glycol cooled units—psi (kPa) . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Deluxe glycol volume approximate gal. (l) max. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Volume in standard Type L copper piping. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Room dew point temperatures °F (°C) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Downflow glycol cooled (DH) piping connection sizes, inches . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Factory-provided piping connection sizes, inches, upflow glycol cooled (VH) . . . . . . . . . . . . . . . . 39
Downflow GLYCOOL (DE) piping connection sizes, inches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Upflow GLYCOOL (VE) piping connection sizes, inches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Glycol pump data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
1-4 fan drycooler physical data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
6- and 8-fan drycooler physical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Refrigerant control settings for water cooled units—psi (kPa) . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Downflow water cooled (DH) piping connection sizes, inches . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Factory-provided piping connection sizes, inches, upflow water cooled (VH) . . . . . . . . . . . . . . . . 52
iv
PRODUCT MODEL INFORMATION
Table i
Model number designation
DH
245
A
VH = Upflow DX
–
Nominal
A = Air
U = 4 Step DX
Capacity in
Cooled
Thousand
DH = Downflow DX BTU/H
W = Water H = DX with
Cooled
Hot gas
Bypass
DE = Downflow DX
G = Glycol
w/ Econ-OCooled
Coil
VE = Upflow DX
w/ Econ-OCoil
A
A = 460/3/60
B = 575/3/60
C = 208/3/60
D = 230/3/60
F = 380/3/50
G = 415/3/50
A
A = Advanced
0 = No
Micro-processor
Reheat
I
0 = No
Humidifier
G = Advanced
E = Electric
I = Infrared
Graphics
Reheat
Humidifier
Micro-processor
H = Hot Water G = Steam Grid
Reheat
Humidifier
H = 230/3/50
J = 200/3/50
M = 380/415/3/50
!
E
G = Hot Gas
Reheat
S = Steam
Generating
Humidifier
T = Steam
Reheat
WARNING
Installation and service of this equipment should be done only by qualified personnel who
have been specially trained in the installation of air conditioning equipment. Improper
installation could result in property damage, injury or loss of life.
!
WARNING
!
CAUTION
Hazardous voltage! Always disconnect power before servicing.
Evaporator unit requires drain connections and may also require water supply. Do not locate
directly above any equipment that could sustain water damage.
Equipment Inspection
Upon arrival of the unit, inspect all items for either visible or concealed damage. Damage should be
immediately reported to the carrier and a damage claim filed with a copy sent to Liebert or to your
sales representative.
v
Table ii
Unit weights
Air Cooled Models
DH/VH, 60 (50) Hz
Water Cooled Models
DH/VH, 60 (50) Hz
Glycol Cooled Models
DH/VH, 60 (50) Hz
GLYCOOL Models
DE/VE, 60 (50) Hz
Capacity and Cooling Type
Weight lbs (kg)
75A
1205 (547)
114A (115A)
1425 (647)
125A (130A)
1440 (645)
199A
1840 (835)
245A
1960 (890)
290A
2025 (920)
380A
2160 (981)
86W
1455 (661)
127W (128W)
1675 (761)
138W (143W)
1690 (768)
219W
2110 (957)
267W
2280 (1036)
315W
2345 (1065)
412W
2500 (1135)
72G
1455 (661)
110G (111G)
1685 (765)
116G (121G
1700 (772)
192G
2130 (967)
240G
2300 (1045)
265G
2365 (1074)
363G
2530 (1148)
72G
1615 (733)
110G (111G)
1845 (837)
116G (121G)
1860 (844)
192G
2385 (1082)
240G
2555 (1159)
363G
2750 (1248)
vi
Introduction
1.0
INTRODUCTION
1.1
System Descriptions
Deluxe System/3 environmental control systems are available in several configurations. Each configuration can operate with either Advanced Microprocessor Controls (AM), or Advanced Microprocessor
Controls with Graphics (AG). A brief description of each, including operational differences, can be
found below. Check model numbers to see what is supplied with your unit.
1.1.1
Compressorized Two-Step Systems
These systems may be air, water, or glycol cooled, depending on the heat rejection method selected.
Cooling
Two stages of mechanical refrigeration are available.
Heating
Three stages of electric reheat are standard; steam/hot water, hot gas (on water and glycol cooled systems) are optional.
Humidification
Infrared is standard. Steam grid and steam generating humidification are optional.
Dehumidification
These systems utilize the lag compressor.
1.1.2
Compressorized Four-Step Systems
The four-stage systems have all the features of a compressorized, two-stage system plus cylinder
unloaders on one head of each compressor. This permits the compressors to operate at a reduced level
and increases energy efficiency during low-load conditions. The system responds to an increasing
room load with either a two-step or a four-step process of increasing the unit's cooling.
Cooling
These systems have four stages of mechanical refrigeration:
a.
b.
c.
d.
Lead compressor at reduced capacity
Lead and lag compressors at reduced capacity
Lead compressor at full capacity; lag compressor at reduced capacity
Lead and lag compressors at full capacity
Heating
Three stages of electric reheat are standard; hot water/steam are optional.
Humidification
Infrared is standard; steam grid and steam generating humidification are optional.
Dehumidification.
These systems utilize the lag compressor.
1
Introduction
1.1.3
GLYCOOL™ (Chilled Glycol Cooling) Systems
GLYCOOL systems have all of the features of a compressorized water or glycol system, plus a second
cooling coil that is connected into the water circuit. When fluid temperature is sufficiently low (below
room temperature), cooling is provided by circulating the fluid through the second cooling coil (flow is
controlled by a motorized valve.) This is then the primary cooling source, and it greatly reduces the
compressor operation.
Cooling
At lower fluid temperatures, the second cooling coil acts as the main cooling system. The motorized
valve opens proportionally to match the room load. At higher fluid temperatures, two or four stages of
mechanical refrigeration control the room load.
Heating
Three stages of electric reheat are standard.
Humidification
Infrared is standard; steam generating is optional
Dehumidification
These systems utilize the lag compressor.
1.1.4
Dual Source Cooling Systems
This system has all the features of a compressorized system but adds a second cooling coil that is connected to a source of chilled water. This second coil is controlled by a modulating control valve. It is
the primary source of cooling and dehumidification so compressor operation is reduced.
Cooling
The second coil acts as the primary cooling system. A modulating valve opens proportionally in
response to the room load. Two and four stages of mechanical refrigeration as a secondary cooling system at higher room loads.
Heating
Three stages of electric reheat are standard.
Humidification
Infrared is standard; steam generating is optional
Dehumidification
These systems utilize the chilled water valve, then the lag compressor if required by the load.
2
Installation
2.0
INSTALLATION
2.1
Room Preparation
The room should be well-insulated and must have a sealed vapor barrier. The vapor barrier in the
ceiling can be a polyethylene film type. Use a rubber-base or plastic-base paint on concrete walls and
floors. Doors should not be undercut or have grilles in them.
Outside, or fresh, air should be kept to an absolute minimum. Outside air adds to the heating, cooling,
humidifying and dehumidifying loads of the site. It is recommended that outside air be kept below 5%
of the total air circulated in the room.
2.2
Location Considerations
For a downflow unit, the unit can sit on an accessible, elevated flooring system. It may be necessary to
furnish additional pedestal support below the unit to ensure maximum structural support. A separate
floor stand for the unit may be used as support, independent of the elevated floor and installed prior
to the flooring system.
For downflow and upflow units, provide approximately 34" (864mm) service clearance on the left,
right and in front of the unit whenever possible. The minimum space required for installation is 18"
(45.7 cm) on the left end, 18" (45.7 cm) on the right end, and 24" (61 cm) in front of the unit. This space
is necessary to permit routine maintenance, such as replacing filters, adjusting the fan speed and
cleaning the humidifier.
NOTE
If high efficiency 6" filters are used, 25" (63.5 cm) is required on the right end for removal
and replacement of filters.
Avoid locating units in an alcove or at the extreme end of a room that has a high aspect ratio (long
narrow room). Also avoid locating units too close together. This tends to reduce the effectiveness of
the air distribution as compared to units located 30-40 feet (9-12m) apart.
3
Installation
2.3
Unit Dimensions
Figure 1
Downflow (DH and DE models) cabinet and floor planning dimensional data
SHADED AREAS
INDICATE A RECOMMENDED
CLEARANCE OF 34 (864mm)
FOR COMPONENT ACCESS AND FILTER
REMOVAL. FOR RECOMMENDED
MINIMUM CLEARANCE, REFER
TO THE INSTALLATION MANUAL.
UNITS WITH
HIGH PRESSU RE VALVE
UNIT DIMENSIONAL DATA
&
FLOOR CUTOUT DIMENSIONS
4
DPN000526 Rev0
Installation
Table 1
Downflow (DH and DE models) dimensions
Air Cooled
Water Cooled
Glycol Cooled
GLYCOOL
60 Hz
50 Hz
DH75A
DH86W
DH72G
DE72G
Dimensional Data
inches (mm)
A
B
C
D
E
F
G
H
J
K
L
DH75A
DH86W
DH72G
DE72G
74
(1880)
70
(1778)
35
(889)
32
(813)
72
(1829)
33
(838)
14-1/4
(362)
54-3/4
(1391)
35-5/8
(905)
63-1/2
1613
27
(686)
DH114A
DH127W
DH110G
DE110G
DH115A
DH128W
DH111G
DE111G
74
(1880)
70
(1778)
35
(889)
32
(813)
72
(1829)
33
(838)
14-1/4
(362)
54-3/4
(1391)
35-5/8
(905)
63-1/2
1613
27
(686)
DH125A
DH138W
DH116G
DE116G
DH130H
DH143W
DH121G
DE121G
74
(1880)
70
(1778)
35
(889)
32
(813)
72
(1829)
33
(838)
14-1/4
(362)
54-3/4
(1391)
35-5/8
(905)
63-1/2
1613
27
(686)
DH199A
DH219W
DH192G
DE192G
DH199A
DH219W
DH192G
DE192G
99
(2515)
95
(2413)
35
(889)
32
(813)
97
(2464)
33
(838)
16-1/4
(413)
77-3/4
(1975)
35-5/8
(905)
88-1/2
(2248)
27
(686)
DH245A
DH267W
DH240G
DE240G
DH245A
DH267W
DH240G
DE240G
99
(2515)
95
(2413)
35
(889)
32
(813)
97
(2464)
33
(838)
16-1/4
(413)
77-3/4
(1975)
35-5/8
(905)
88-1/2
(2248)
27
(686)
DH290A
DH315W
DH265G
DH290A
DH315W
DH265G
99
(2515)
99
(2515)
35
(889)
32
(813)
97
(2464)
33
(838)
16-1/4
(413)
77-3/4
(1975)
35-5/8
(905)
--
--
DH380A
DH412W
DH363G
DE363G
DH380A
DH412W
DH363G
DE363G
122
(3098)
118
(2997)
35
(889)
32
(813)
120
(3048)
33
(838)
16-1/4
(413)
100-3/
4
(2559)
35-5/8
(905)
111-1/
2
(2832)
27
(686)
5
Installation
Figure 2
Upflow 6, 8 and 10 ton (VH and VE models) cabinet and floor planning dimensional data
UNIT DIMENSIONAL DATA
Projection of
Display Bezel
5/8" (16mm) 35" overall
74
"
(18 ove
80 ral
70 mm l
Ple " (1 )
nu 778
m
m
Fla m)
ng
e
(889mm)
32"
(838mm)
Plenum
Flange
2" (51mm)
2"
(51mm)
72"
(1829mm)
DUCT CONNECTION DATA
Models With Rear Return
Flange provided on
blower outlet for
supply air ducting
Air grille
supplied on
units with
front return
air only
1" (25.4mm) flange
for decorative
plenum alignment
1" (25.4mm)
72" base
(1829mm)
33" Base
(838mm)
Shaded areas indicate
a recommended
clearance of 34"
(864mm) for component
access and filter
removal
20-1/4"
(514mm)
FLOOR CUTOUT DIMENSIONS
Models With Bottom Return
33"
(838mm)
4-1/2"
(114mm)
( 55 22 "
9m
m)
69-3/4"
(1172mm)
Air return
opening
4"
(102mm)
11"
(279mm)
69-3/4"
(1172mm)
Air return
opening
2-1/8"
(54mm)
72"
(1829mm)
Flo
or
L
1-1/8"
(29mm)
ev
el
6
DPN000527 Rev0
Installation
Figure 3
Upflow 6, 8 and 10 ton (VH and VE models) blower duct and deck dimensional data
74" ref
(1880mm)
Duct Flange on Blower
Top of Unit
A
D
F
Blower Deck
B
35" ref
(889mm)
C
72" ref
(1829mm)
Front of Unit
Blower Duct Flange Location
Front or Rear Air Supply
DPN000528 Rev0
Table 2
Upflow 6, 8 and 10 ton (VH and VE models) blower duct and deck dimensional data
Blower
Supply
Motor
HP
TOP FRONT
A
B
C
D
F
1-5
22-7/8
(581)
3-1/2
(89)
18-13/16
(478)
16-3/16
(411)
1-1/2
(38)
TOP REAR
1-5
22-7/8
(581)
12-5/16
(313)
18-13/16
(478)
16-3/16
(411)
1-1/2
(38)
TOP FRONT
1-5
22-7/8
(581)
3-1/2
(89)
14-7/8
(378)
16-3/16
(411)
1-1/2
(38)
TOP REAR
1-5
22-7/8
(581)
12-5/16
(313)
14-7/8
(378)
16-3/16
(411)
1-1/2
(38)
TOP FRONT
1-5
22-7/8
(581)
5-7/8
(149)
12-7/16
(316)
13 3/4
(349)
1-1/2
(38)
TOP REAR
1-5
22-7/8
(581)
12-5/16
(313)
12-7/16
(316)
13 3/4
(349)
1-1/2
(38)
TOP FRONT
1.5-5
22-7/8
(581)
3-1/2
(89)
18-13/16
(478)
16-3/16
(411)
1-1/2
(38)
TOP REAR
1.5-5
22-7/8
(581)
12-5/16
(313)
18-13/16
(478)
16-3/16
(411)
1-1/2
(38)
TOP FRONT
2-7.5
22-7/8
(581)
3-1/2
(89)
14-7/8
(378)
16-3/16
(411)
1-1/2
(38)
22-7/8
(581)
12-5/16
(313)
14-7/8
(378)
16-3/16
(411)
15 x 15
VH075A
VH086W
VH072G
VE072G
15 x 11
12 x 9
15 x 15
VH115A/VH114A
VH128W/VH127W
VH111G/VH110G
VE111G/VE110G
15 x 11
2-5
TOP REAR
7.5
1-1/2
(38)
4 1/2
(114)
TOP FRONT
2-5
22-7/8
(581)
3-1/2
(89)
18-13/16
(478)
16-3/16
(411)
1-1/2
(38)
TOP REAR
2-5
22-7/8
(581)
12-5/16
(313)
18-13/16
(478)
16-3/16
(411)
1-1/2
(38)
TOP FRONT
3-10
22-7/8
(581)
3-1/2
(89)
14-7/8
(378)
16-3/16
(411)
1-1/2
(38)
3-5
22-7/8
(581)
7.5-10
23 7/8
(606)
12-5/16
(313)
14-7/8
(378)
16-3/16
(411)
15 x 15
VH130A/VH125A
VH143W/VH138W
VH121G/VH116G
VE121G/VE116G
Dimensional Data inches (mm)
15 x 11
TOP REAR
7
1-1/2
(38)
4 1/2
(114)
Installation
Figure 4
Upflow 15, 20 and 22 ton (VH and VE models) cabinet and floor planning dimensional data
Projection of
Display Bezel 35" overall
(889mm)
5/8" (16mm)
2"
(51mm)
32"
(838mm)
Plenum
Flange
99
"
(25 ove
15 ral
mm l
)
UNIT DIMENSIONAL DATA
9
Ple (241 5"
nu 3m
m m)
Fla
ng
e
2"
(51mm)
76"
(1930mm)
DUCT CONNECTION DATA
Models With Rear Return
Air grille
supplied on
units with
front return
Shaded areas
air only
indicate a
recommended
clearance of 34"
(864mm) for
component
access and filter
removal
(83 33"
8m
m
Flanges provided on
blower outlets for
supply air ducting
97" Base
(2464mm)
33" Base
(838mm)
1" (25.4mm) flange
for decorative
plenum alignment
1"
(25.4mm)
FLOOR CUTOUT DIMENSIONS
Models With Bottom Return
)
(55 22"
9m
m)
24-1/4"
(616mm)
5-1/2"
(140mm)
Air return
opening
94-3/4"
(2407mm)
4"
(102mm)
94-3/4"
(2407mm)
97"
(2464mm)
11"
(279mm)
Flo
or
Le
1-1/8"
ve
l
(29mm)
8
Air
return
opening
2-1/8"
(54mm)
DPN000529 Rev0
Installation
Figure 5
Upflow 15, 20 and 22 ton (VH and VE models) blower duct and deck dimensional data
TOP OF UNIT
99" (2514.6) ref.
Duct Flanges on Two Blower
D
C
E
Blower Deck
A
F
B
35"
(889mm)
ref.
C
76"
(1930.4mm)
ref.
FRONT OF UNIT
Front or Rear Air Supply
Blower Duct Flange Location
DPN000530 Rev0
Table 3
Upflow 15, 20 and 22 ton (VH and VE models) blower duct and deck dimensional data
Blower
Supply
TOP
FRONT
15 x 15
VH199A
VH219W
VH192G
VE192G
TOP
REAR
TOP
FRONT
15 x 11
TOP
REAR
12 x 9
TOP
FRONT
TOP
REAR
TOP
FRONT
15 x 15
VH245A
VH290A
VH267W
VH315W
VH240G
VH265G
VE240G
TOP REAR
15 x 11
TOP
FRONT
TOP
REAR
Dimensional Data inches (mm)
Motor
HP
A
B
C
D
E
F
3-7.5
20-3/8 (518)
10
22-7/8 (581)
3-1/2
(89)
18-13/16
(478)
16-3/16
(411)
12-11/16
(322)
1-1/2 (38)
3-5
20-3/8 (518)
16-3/16
(411)
1-1/2 (38)
25-3/8 (645)
18-13/16
(478)
12-11/16
(322)
7.5-10
12-5/16
(313)
10
(254)
4-1/2 (114)
5-7.5
20-3/8 (518)
10
22-7/8 (581)
3-1/2
(89)
14-7/8
(378)
16-3/16
(411)
12-5/16
(313)
14-7/8
(378)
16-3/16
(411)
5-7/8
(149)
12-7/16
(316)
13-3/4
(349)
12-5/16
(313)
12-7/16
(316)
13-3/4
(349)
18-5/8
(473)
4-1/2 (114)
3-1/2
(89)
18-13/16
(478)
16-3/16
(411)
12-11/16
(322)
1-1/2 (38)
12-5/16
(313)
18-13/16
(478)
16-3/16
(411)
12-11/16
(322)
1-1/2 (38)
10 (254)
4 1/2 (114)
16-5/8
(422)
1-1/2 (38)
14-1/2
(368)
4 1/2 (114)
15
25-3/8 (645)
5
20-3/8 (518)
7.5-15
25-3/8 (645)
7.5
20-3/8 (518)
10
22-7/8 (581)
15
25-3/8 (645)
7.5-15
25-3/8 (645)
5-7.5
20 3/8 (518)
10
22-7/8 (581)
5
20 3/8 (518)
7.5-10
25 3/8 (645)
7.5
20 3/8 (518)
10
22-7/8 (581)
15
25 3/8 (645)
20
27 7/8 (708)
7.5-15
25 3/8 (645)
20
27 7/8 (708)
9
3-1/2
(89)
12-5/16
(313)
14-7/8
(378)
14-7/8
(378)
16-3/16
(411)
16-3/16
(411)
16-5/8
(422)
14-1/2
(368)
1-1/2 (38)
16 5/8
(422)
1-1/2 (38)
14 1/2
(368)
4-1/2 (114)
22-3/4
(578)
18-5/8
(473)
14-1/2
(368)
1-1/2 (38)
4-1/2(114)
Installation
Figure 6
Upflow 30 ton (VH and VE models) cabinet and floor planning dimensional data
Projection of
display bezel
5/8" (16mm)
35"
(889mm)
Overall
32"
(838mm)
Plenum
Flange
2"
(51mm)
UNIT DIMENSIONAL DATA
122"
(3099mm)
Overall
118"
(2997mm)
Plenum Flange
2" (51mm)
76"
(1930mm)
DUCT CONNECTION DATA
Models With Rear Return
Flanges provided on
blower outlets for
supply air ducting
Air grille
supplied on
units with
front return
air only
Shaded areas indicate a
recommended clearance
of 34" (864mm) for
component access and
filter removal
1" (25.4mm) flange
for decorative
plenum alignment
1"
(25.4mm)
120"
(3048mm)
Base
33"
(838mm)
Base
FLOOR CUTOUT DIMENSIONS
Models With Bottom Return
(83 33"
8m
m)
24-1/4"
(616mm)
5-1/2"
(140mm)
( 55 22"
9m
m)
Air Return
Opening
113-1/2"
(2883mm)
4"
(102mm)
113-1/2"
(2883mm)
11"
(279mm)
Air Return
Opening
4-1/4"
(108mm)
120"
(3048mm)
Flo
3-1/4"
(83mm)
or
L
10
ev
e
l
DPN00531 Rev0
Installation
Figure 7
Upflow 30 ton (VH and VE models) blower duct and deck dimensional data
122" (3098.8) ref.
TOP OF UNIT
Duct Flanges on Three Blower
D
C
E
G
Blower Deck
A
35"
(889)
ref.
C
E
F
B
76"
(1930.4)
ref
FRONT OF UNIT
Front or Rear Air Supply
Blower Duct Flange Location
DPN000532 Rev0
Table 4
Upflow 15, 20 and 22 ton (VH and VE models) blower duct and deck dimensional data
Blower
15 x 5
VH380A
VH412W
VH363G
VE363G
15 x11
Supply
Motor
HP
Dimensional Data inches (mm)
A
B
C
D
E
F
G
TOP
FRONT
10
22-7/8
(581)
3-1/2
(89)
18-13/16
(478)
16-3/16
(411)
10
(254)
1-1/2
(38)
18-5/8
(473)
TOP
REAR
10
22-7/8
(581)
12-5/16
(313)
18-13/16
(478)
16-3/16
(411)
10
(254)
4-1/2
(114)
18 5/8
(473)
TOP
FRONT
TOP
REAR
10-15
20
10-20
27-7/8
(708)
3-1/2
(89)
14-7/8
(378)
16-3/16
(411)
10
(254)
27-7/8
(708)
12-5/16
(313)
14-7/8
(378)
16-3/16
(411)
10
(254)
11
1-1/2
(38)
4-1/2
(114)
4-1/2
(114)
14-11/16
(373)
14-11/16
(373)
Installation
2.4
Piping
All fluid and refrigeration connections to the unit, with the exceptions of the condensate drain and
live steam, are sweat copper. Factory-installed piping brackets must not be removed. Field-installed
piping must be installed in accordance with local codes and must be properly assembled, supported,
isolated and insulated. Avoid piping runs through noise-sensitive areas, such as office walls and conference rooms.
Refer to specific text and detailed diagrams in this manual for other unit-specific piping requirements
2.4.1
Drain Line
A 3/4" NPT is provided for the evaporator coil condensate drain. This drain line also drains the
humidifier, if applicable. The drain line must be located so it will not be exposed to freezing temperatures. The drain should be at least the full size of the drain connection and pitched a minimum of 1/8"
per ft. (11mm per meter).
NOTE
This line may contain boiling water. Use copper or other suitable material for the drain line.
For units without a condensate pump
The unit is shipped from the factory with an internally-mounted trap. No external trap is
required. The drain line must comply with all applicable codes.
For units with a factory-installed condensate pump option
The unit is shipped from the factory with a condensate pump installed. The condensate pump
discharge (drain) line must comply with all applicable codes.
For units with a field-installed condensate pump
The unit is shipped from the factory with the condensate pump option, unmounted in the unit,
which must be installed in the field. The unit has an internally mounted trap. The drain line
from the unit to the condensate pump does not require a trap. The discharge (drain) line from
the pump must comply with all applicable codes.
2.4.2
Piping Considerations for Raised-Floor Applications
All piping below the elevated floor must be located so that it offers the least resistance to air flow.
Careful planning of the piping layout under the raised floor is required to prevent the air flow from
being blocked. When installing piping on the subfloor, it is recommended that the pipes be mounted in
a horizontal plane rather than stacked one above the other. Whenever possible, the pipes should be
run parallel to the air flow.
2.5
Electrical Connections
Three-phase electrical service is required for all models in either 208, 230, 460 or 575V, 60Hz; or 200,
230 or 400V, 50 Hz. Electrical service shall conform to national and local electrical codes.
Install a manual electrical disconnect switch within 5 feet (1.6 m) of the unit in accordance with
codes. A factory-supplied disconnect switch may be factory-mounted within the unit and accessible
from the exterior.
12
Installation
Figure 8
Electrical connection details
ROOM UNIT CONNECTIONS
NOTES
L1
3-phase line voltage
supply to line voltage
connection block or
optional main disconnect
switch (Note 2)
To line voltage
components on Liebert
room unit electric panel
L2
L3
To line voltage
components in
Liebert room
unit
OR
Earth ground to ground
lug bolt or optional
ground bar
37
38
24
50
51
55
56
77
2-wire connection for
each Special Alarm
(Note 4)
22 ga. 4-wire cable
4-pin plug connections for
optional remote
temperature and humidity
sensor
Control
Board
P16
75
76
70
71
2-wire connection for
common alarm
Wires 70 & 71 are connected
to compressor side switches
and Econ-O-Coil relay (R5).
R5 is provided on FE/UE
units only.
8. Lee-Temp tanks and assembly
supplied on air-cooled
condensers with Lee-Temp
control systems only.
3-wire line voltage
connection plus ground for
glycol pump. An additional
3-wire line voltage needed
for dual pump packages
(Note 7).
Wire Legend
Factory-supplied line
voltage wiring
See Note 8
Diagram is for direct
drive air-cooled
condensers
(for air-cooled units)
and direct drive
drycoolers
(for glycol/GLYCOOL
units).
Electric Panel
Interconnected
7. Glycol pump package supplied
with drycoolers only. Pump 2 is
supplied only when dual pump
package is ordered.
Remote Heat Rejection Connections
2-wire connection plus
ground for Lee-Temp heater
pads (Note 8)
1
6. Field-supplied disconnect switch
mounted within sight of
condenser/drycooler and in
accordance with local codes or
ordered as optional equipment
and factory-installed in Liebert
condenser/drycooler. CDF-065,
CDF-083, CDF-086, CDF-097 and
CDF-104L are single-phase fan
speed condensers. All other
condensers and all drycooler and
pump packages require a 3-phase
line voltage supply.
Terminals 75 & 76 are
6-inch
pigtails at connected to common alarm
junction relay (K3) NO contact (max 1A
at 24V)
box
2-wire connection for
heat rejection interlock
(Note 5)
2-wire connection for heat
rejection interlock
3. For remote unit shutdown,
replace jumper between 37 & 38 at
terminal strip with Normally
Closed switch having a minimum
75VA rating.
5. Heat rejection interlock is not
supplied on chilled water models.
2-wire connection
optional SiteScan
Earth Ground
2. Field-supplied room unit main
disconnect switch in accordance
with local codes ordered as
optional equipment and factoryinstalled in Liebert room unit.
4. Special alarm connection made by
adding Normally Open contacts
between Terminals 24 & 50, 24 &
51, 24 & 55 and 24 & 56. Only one
alarm (between 24 & 50) is
available on standard
microprocessor.
78
2-wire connection for
remote unit shutdown
(Note 3)
3- or single-phase line voltage
supply to optional main
disconnect switch (Note 6)
1. Refer to specification sheet for
Full Load Amps and Wire Sizing
Amps.
2
1 fan
Field-supplied line
voltage wiring
Factory-supplied 24V,
NEC Class 2 wiring
Field-supplied 24V
NEC Class 2 wiring
Field-supplied earth
grounding wire
2 fan
3 fan
13
Installation
Figure 9
Electrical field connections
Field-supplied disconnect switch when factory-installed
unit disconnect switch is not provided
Factory-installed unit
disconnect switch (optional)
Monitoring panel
3-phase
electric
service
not by
Liebert
Field-wired to components
on electric panel
Electric connection block
3-phase connection; electric
service connection terminals
when factory disconnect switch
is supplied
3-phase connection; electric service
connection terminals when factory
disconnect switch is not supplied
Earth ground connection (60Hz);
connection terminal for field-supplied
earth grounding wire
Factory-installed disconnect
switch (optional)
Smoke detector alarm
connections; field-supplied 24V;
Class 2 wire to remote alarm
circuits; factory-wired contacts
from optional smoke detector are
#91-comm., #92-NO and #93-NC
Earth ground bar (50Hz only); connection
terminals with factory-ground from each
high-voltage component for field-supplied
earth grounding wire
3-phase electric service not by Liebert
Common alarm connection;
field-supplied 24V; Class 2 wire
to common alarm from pigtails
75 +76, which are
factory-connected to common
alarm relay (R3)
Special alarm connections; field-supplied 24V, Class 1
wire for special alarms; connections made by adding
normally open contact between terminals (24 & 50) for
standard microprocessor; advanced microprocessor
has four alarms at terminal: 24 & 50; 24 & 51; 24 & 55
and 24 & 56
Electric handy box
factory-installed
with cover
Heat rejection connection;
field-supplied 24V; Class 1 wiring
to interlock heat rejection from
pigtails 70 and 71, which are
factory-connected to compressor
side switches
Analog inputs; optional terminals 41 to 48 provide
connections for shielded, twisted-pair cable to as
many as four customer supplied analog sensors
(AM and AG only)
Site monitoring connection; terminals 77(-) and 78(+)
are for connection of a 2-wire, twisted-pair
communication cable (available from Liebert or
others) to optional SiteScan and are
factory-connected to the interface board on the unit
Condensate pump connection for
pumps shipped loose; factory-supplied
wiring from pump to pigtails; fuses are
installed on electric panel
Electric conduit knockouts on bottom and
rear of wire raceway; knockout sizes are
1-3/8" (34.9mm) or 1-3/4" (44.5mm) or
2-1/2" (63.5mm)
Remote unit shutdown; replace existing
jumper between Terminals 37 and 38 with
a normally closed switch having a
minimum 50VA rating; use field-supplied
Class 1 wire
DPN000538 Rev1
NOTE
Refer to specification sheet for full load amp and wire size amp ratings.
14
Installation
2.6
Air Distribution Considerations
2.6.1
Raised-Floor Air Flow Distribution Considerations
To ensure proper air distribution, any unusual restrictions within the air circuit must be avoided. For
under-floor air distribution, observe the following guidelines:
Select the air supply grilles and perforated panels for the raised floor to ensure minimum loss of pressure in the circuit. Air volume dampers on grilles, which extend several inches below the surface of
the raised floor, are usually detrimental to airflow. Consideration of the height of the damper on the
grille in conjunction with the floor height will determine whether this type of grille may be used.
The grilles used in raised floors vary in size, the largest being approximately 18" x 6" (457 x 152 mm).
A larger grille size would be detrimental to the structural capacity of the raised floor panel. An
18" x 6" (457 x 152mm) heavy-duty pencil-proof type grille typically has 56 square inches (0.036m2) of
free area. Perforated panels are available from various manufacturers of raised floors. These panels
are usually 2' x 2' (610 x 610mm) square and have a nominal free area of approximately 108 to 144
square inches (0.07 to 0.09 m2). Use caution in selecting perforated panels as some manufacturers
have only 36 to 40 square inches (0.023 to 0.026 m2) of free area, requiring four times as many panels.
Avoid floor elevations below 7-1/2" (190.5mm), loosely installed flooring systems, and below-floor
obstructions such as: electrical wiring chases, unusually long computer system cables, or piping clusters.
All piping below the elevated floor must be located so that it offers the least resistance to air flow.
Careful planning of the piping layout under the raised floor is required to prevent the air flow from
being blocked. When installing piping on the subfloor, it is recommended that the pipes be mounted in
a horizontal plane rather than stacked one above the other. Whenever possible, the pipes should be
run parallel to the air flow.
Always check specifications of the floor supplier before specifying the total number of perforated panels and grilles required to handle the air flow. The proper specifications for grilles and perforated panels should indicate the total free area required for air delivery rather than the number of panels and
grilles. (See Table 5 below for recommended free area required for each model.) This table indicates
the recommended free area based on having the supply air grilles and perforated panels sized to handle approximately 75% of the total cubic feet per minute (CFM) of the units at a velocity of 550 to 600
ft./min. (2.8 - 3.1 m/s). The remaining 25 percent of the air flow in the raised floor passes through
cable cutouts, cracks between the panels and other leakage areas.
Table 5
Recommended free area ft2 (m2 for grilles or perforated panels at output velocities of
550 and 600 fpm (2.8 and 3.1 m/s)
Model DH/DE or FH
60 (50) Hz
Direct
Expansion
Units
2.6.2
550 fpm
(2.8 m/s)
600 fpm
(3.1 m/s)
75A
86W
72G
4.6 (0.41)
4.2 (0.38)
114A (115A)
122W (128W)
110G (111G)
6.3 (0.57)
5.8 (0.52)
125A (130A)
138W (143W)
116G (121G)
7.7 (0.69)
7.1 (0.64)
199A
219W
192G
11.5 (1.04)
10.5 (0.95)
245A
267W
240G
13.9 (1.25)
12.8 (1.15)
290A
315W
265G
16.4 (1.48)
15.0 (1.35)
380A
412W
363G
20.4 (1.84)
18.8 (1.70)
Upflow Systems Additional Installation Considerations
Upflow models can be configured in several different ways with front return, rear return, or bottom
return and top front supply or top rear supply (on DX models). For in-room applications with no ductwork, and optional plenum with grill, proper clearance must be maintained on the return air side of
the unit. For a front return, this means several feet in front of the unit. For a bottom return, at least
6-8 inches of unrestricted under-floor height is needed.
15
Installation
2.6.3
Ducted Application Installation
Duct flanges are supplied on the blower outlets. Follow the SWACNA-Duct Construction Standard for
single-, dual-, or triple-blower systems. Do not run ductwork off the perimeter flange on the top of the
unit. This flange is for positioning and attaching the optional air discharge plenum with grill. Attaching a duct to this flange may reduce airflow to inadequate levels.
Figure 10 Ducting configurations
2
1
2
2
1
1
1. Straight section of duct off of unit to be 1.5 to 2.5 times the
longest blower dimension.
2. Typical ducting shown; may run to either side.
* Follow standard practices on all duct work.
2.6.4
DPN000533 Rev0
Plenum Installation
When installing the plenum to the top of system, secure the plenum to the unit flange using sheet
metal screws.
2.6.5
Filter Box Installation
When installing the filter box to the back of the unit, secure the box to the unit using self tapping
sheet metal screws. Seal around all edges with a silicone sealant to prevent air leakage.
16
Installation
Figure 11 Plenum dimensional data for 6 - 22 ton models
NOTE: FLANGES PROVIDED
ON BLOWER(S) OUTLET
FOR SUPPLY AIR DUCTING
WHEN SOLID PANEL
PLENUM IS USED.
1"
(25mm)
D
C
J
1"
(25mm)
2"
(50mm)
18"
(457mm)
H
1"
(25mm)
BOTH TOP DUCT OPENINGS AND
FRONT GRILLE ARE SHOWN.
SEE SPECIFICATION SHEET
FOR SPECIFIC APPLICATION.
E
B
A
F
1"
(25mm)
D
2"
(50mm)
C
2"
(50mm)
1"
(25mm)
FLANGE IS STANDARD ON ALL UNITS
EXCEPT DOWNFLOW (DH/DE)
MODELS WHERE IT MUST BE
SPECIFIED IF REQUIRED.
DPN000620 Rev0
Table 6
Plenum dimensional data for 6 - 22 ton models, in. (mm)
Model
DH/DE/VH/VE-75A, 86W, 72G
DH/DE/VH/VE-115A, 128W, 111G
DH/DE/VH/VE-114A, 127W, 110G
DH/DE/VH/VE-130A, 143W, 121G
DH/DE/VH/VE-125A, 138W, 116G
DH/DE/VH/VE-199A, 219W, 192G
DH/DE/VH/VE-245A, 267W, 240G
DH/VH/-290A, 315W, 265G
A
B
C
D
E
F
Grille Free Area
Sq Ft (sq m)
74
(1880)
34
(864)
70
(1778)
32
(813)
60
(1524)
7
(178)
5.85
(.54)
99
(2515)
34
(864)
95
(2413)
32
(813)
70
(1778)
14-1/2
(368)
6.83
(.63)
Plenum Height In. (mm)
H
J
20 (508)
22-3/4 (578)
34-3/4 (883)
1 (25)
2-3/8 (60)
2-3/8 (60)
17
Installation
Figure 12 Plenum dimensional data for 30 ton models
Note: Flanges provided
on blower outlet(s) for
supply air ducting when
solid panel plenum is used
1" (25mm)
D
L
C
18" (457mm)
K
1"(25mm)
G
B
F
E
H
J
Both top duct openings and
front grilles are shown. See
specification sheet for specific
application
E
A
1"(25mm)
D
C
2"
(50mm)
2"
(50.8mm)
1"
(25mm)
Flange is standard on all
units except downflow (DH/DE)
models where is must be specified
if required
DPN000621 Rev0
Table 7
Plenum dimensional data for 30 ton models in. (mm)
Model
DH/DE/VH/VE-380A,
412W, 363G
A
B
C
D
E
F
G
H
J
K
L
122
34
118
32
44
3-1/2
4
7
16
20
1
(3099) (864) (2997) (813) (1118) (89) (102) (178) (406) 508) (25)
18
Grille
Free Area
Sq Ft (sq m)
10.14
(.94)
Air Cooled Models
3.0
AIR COOLED MODELS
3.1
Condenser Location
3.1.1
Outdoor Prop Fan Models
The air cooled condenser should be located for maximum security and maintenance accessibility.
Avoid ground level sites with public access or areas that contribute to heavy snow or ice accumulations. Utilize centrifugal condensers whenever interior building locations must be used. To assure
adequate air supply, Liebert recommends that condensers be located in a clean air area, away from
loose dirt and foreign matter that may clog the coil. Condensers should not be located in the vicinity of
steam, hot air or fume exhausts. Also, condensers should be located no closer than 3 feet (1 meter)
from a wall, obstruction or adjacent unit.
Install condensers in a level position to assure proper refrigerant flow and oil return. For roof installation, mount condensers on steel supports in accordance with local codes. To minimize sound and
vibration transmission, mount steel supports across load bearing walls.
For ground installation, a concrete pad will provide adequate support. Condenser legs have mounting
holes for securing the condenser to steel supports or concrete pad.
3.1.2
Indoor Piggyback Models
The piggyback condenser can be located directly behind the Deluxe unit or in a separate remote
indoor location. It may be placed directly against an outside wall, with the proper openings cut in the
wall for entering and leaving air. If it cannot be located near a wall, the unit may be ducted to the outside. Proper grilles/screens are required on the outside wall.
3.2
Electrical Connections
3.2.1
High Voltage
High voltage electrical service is required for all air cooled condensers at the location of the condenser. This power supply does not have to be the same voltage as the indoor unit. This separate
power source may be 208/230, 460 or 575V, 60Hz; or 200/230 or 380/415V, 50Hz. The disconnect
switch may be factory supplied and mounted in the electrical panel or field supplied and mounted per
local and national codes.
3.2.2
Low Voltage
A control interlock between the condenser and the indoor unit is required and is connected between
70 and 71 on the wire raceway in the compressor compartment of the indoor unit and the electric
panel of the air cooled condenser.
3.2.3
Lee-Temp/Flood Back Head Pressure Control Condensers (Standard on Piggyback
Models)
Lee-Temp condensers require a separate power supply for the heated receivers. This power supply is
connected to the electrical connection box on the end of the receiver.
19
Air Cooled Models
3.3
Refrigerant Piping
All refrigeration piping should be installed with high temperature brazed joints. Prevailing good
refrigeration practices should be employed for piping supports, leak testing, dehydration and charging of the refrigeration circuits. The refrigeration piping should be isolated from the building by the
use of vibration isolating supports. Piping, including inverted trap(s), must be routed to allow
unobstructed access to the panel per the NEC.
Traps should be installed in the hot gas lines on vertical risers every 25 feet (7.6 meters) in elevation.
These traps will collect condensed refrigerant and refrigerant oil during the off cycle of the unit and
ensure flow of refrigerant oil during operation. Hot gas vertical risers may require downsizing of the
line to provide for adequate refrigerant velocities to move oil up the riser. This is especially true on
systems with unloaders.
Contact your local Liebert representative for factory approval whenever a refrigerant piping run
exceeds 200 feet (60 meters) equivalent length or when condensers must be located below the level of
the cooling coil.
Table 8
Recommended line sizes – O.D. copper
75A
114A (115A)
125A (130A)
199A
245A
290A
380A
Hot Gas Liq. Hot Gas Liq. Hot Gas Liq. Hot Gas Liq. Hot Gas Liq. Hot Gas Liq. Hot Gas Liq.
Line
Line
Line
Line
Line
Line
Line
Line
Line
Line
Line
Line
Line
Line
50 ft
(15m)
5/8
1/2
7/8*
1/2
7/8*
1/2
7/8
5/8
1-1/8*
7/8
1-1/8
7/8
1-3/8
7/8
100 ft.
(30m)
7/8
1/2
7/8*
5/8
7/8
5/8
1-1/8*
7/8
1-1/8
7/8
1-1/8
7/8
1-3/8
7/8
150 ft.
(45m)
7/8
5/8
7/8
5/8
7/8
5/8
1-1/8
7/8
1-1/8
7/8
1-1/8
7/8
1-3/8
1-1/8
*With 4-Step Models, use one (1) trade size smaller (7/8 = 3/4, 1-1/8 = 7/8).
20
Air Cooled Models
Figure 13 Piping: Fan speed control condensers
Returning
liquid line (Typ.)
Entering hot
gas line (Typ.)
10060Pg4
Inverted traps are to be field-supplied and installed (Typ.).
When installing traps, clearance must be provided for
swing of end access door. Traps are to extend above base
of coil by a minimum of 7-1/2" (190mm).
Table 9
Fan speed control condenser piping connection sizes - Cu OD
Entering Hot
Gas Line
In. (mm)
Returning
Liquid Line
In. (mm)
CDF-065
1/2 (12.7)
1/2 (12.7)
CDF-083L
1/2 (12.7)
1/2 (12.7)
Condenser Model
Number
CDF-086
7/8 (22.2)
1/2 (12.7)
CDF-097/107C
7/8 (22.2)
1/2 (12.7)
CDF-104L
7/8 (22.2)
1/2 (12.7)
CDF-130
7/8 (22.2)
5/8 (15.9)
CDF-165L
7/8 (22.2)
5/8 (15.9)
CDF-175
7/8 (22.2)
5/8 (15.9)
CDF-205L
1-1/8 (28.6)
7/8 (22.2)
CDF-217C/216C
1-1/8 (28.6)
7/8 (22.2)
CDF-251L
1-1/8 (28.6)
7/8 (22.2)
CDF-258
1-1/8 (28.6)
7/8 (22.2)
CDF-291
1-1/8 (28.6)
1-1/8 (28.6)
CDF-308L
1-3/8 (34.9)
1-1/8 (28.6)
CDF-330L
1-3/8 (34.9)
1-1/8 (28.6)
CDF-360/349C
1-3/8 (34.9)
1-1/8 (28.6)
CDF-415L
1-3/8 (34.9)
1-1/8 (28.6)
CDF-480C
1-5/8 (41.3)
1-1/8 (28.6)
CDF-510C
1-5/8 (41.3)
1-1/8 (28.6)
For runs longer than 150 feet (45.7m) equivalent length, consult factory for proper line sizing.
21
Air Cooled Models
Figure 14 Piping: Lee-Temp control condensers
Entering hot gas line (Typ.)
Returning liquid line (Typ.)
10061Pg6
Lee-Temp receiver tank
Table 10
Lee-Temp control condenser piping connection sizes
Lee-Temp Connections-ODS
inches (mm)
Condenser Connections-ODS
inches (mm)
Model #
Hot Gas
Tee F
Liq. to L-T
Valve C
Receiver
Out D
(2) W-4
1-1/8 (28.6)
7/8 (22.2)
5/8 (15.9)
(2) W-4
1-1/8 (28.6)
7/8 (22.2)
5/8 (15.9)
(2) W-4
1-1/8 (28.6)
7/8 (22.2)
5/8 (15.9)
1/2 (12.7)
(2) W-4
1-1/8 (28.6)
7/8 (22.2)
5/8 (15.9)
Hot Gas A
Liquid B
CDL-065
1/2 (12.7)
1/2 (12.7)
CDL-083L
1/2 (12.7)
1/2 (12.7)
CDL-086
7/8 (22.2)
1/2 (12.7)
CDL-097
7/8 (22.2)
Lee-Temp
Size
CDL-104L
7/8 (22.2)
1/2 (12.7)
(2) W-4
1-1/8 (28.6)
7/8 (22.2)
5/8 (15.9)
CDL-130
7/8 (22.2)
5/8 (15.9)
(2) W-4
1-1/8 (28.6)
7/8 (22.2)
5/8 (15.9)
CDL-165
7/8 (22.2)
5/8 (15.9)
(2) W-4
1-1/8 (28.6)
7/8 (22.2)
5/8 (15.9)
CDL-175
7/8 (22.2)
5/8 (15.9)
(2) W-4
1-1/8 (28.6)
7/8 (22.2)
5/8 (15.9)
CDL-205L
1-1/8 (28.6)
7/8 (22.2)
(2) W-4
1-1/8 (28.6)
7/8 (22.2)
5/8 (15.9)
CDL-217C
1-1/8 (28.6)
7/8 (22.2)
(2) W-5
1-3/8 (34.9)
7/8 (22.2)
7/8 (22.2)
CDL-251L
1-1/8 (28.6)
7/8 (22.2)
(2) W-4
1-3/8 (34.9)
7/8 (22.2)
7/8 (22.2)
CDL-258
1-1/8 (28.6)
7/8 (22.2)
(2) W-5
1-3/8 (34.9)
7/8 (22.2)
7/8 (22.2)
CDL-291
1-1/8 (28.6)
5/8 (15.9)
(2) W-5
1-3/8 (34.9)
7/8 (22.2)
7/8 (22.2)
CDL-308L
1-3/8 (34.9)
1-1/8 (28.6)
(2) W-5
1-3/8 (34.9)
7/8 (22.2)
7/8 (22.2)
CDL-330L
1-3/8 (34.9)
1-1/8 (28.6)
(2) W-5
1-3/8 (34.9)
7/8 (22.2)
7/8 (22.2)
CDL-360
1-3/8 (34.9)
1-1/8 (28.6)
(2) W-5
1-3/8 (34.9)
7/8 (22.2)
7/8 (22.2)
CDL-415L
1-3/8 (34.9)
1-1/8 (28.6)
(2) W-5
1-3/8 (34.9)
7/8 (22.2)
7/8 (22.2)
CDL-480C
1-5/8 (41.3)
1-1/8 (28.6)
(2) W-6
1-3/8 (34.9)
1-1/8 (28.6)
7/8 (22.2)
CDL-510C
1-5/8 (41.3)
1-1/8 (28.6)
(2) W-41
1-3/8 (34.9)
1-1/8 (28.6)
7/8 (22.2)
For runs longer than 150 feet (45.7m) equivalent length, consult factory for proper line sizing.
22
Air Cooled Models
Figure 15 Downflow air cooled (DH) piping connections
MONITORING
PANEL
NOTE: Install all piping
per local codes.
C - Steam Reheat Supply Line
D - Hot Water Reheat Supply Line.
Condensate Drain. Field pitch a min. of
1/8" (3.2mm) per ft. (305mm). 3/4" NPT for units
without factory installed condensate pump. Do
not install an external trap. 1/2" OD CU for units
with factory installed condensate pump.
E - Steam Reheat Return Line (Field
install factory supplied steam
trap with vacuum breaker).
1/4" OD CU Humidifier Supply Line (Steam Gen./Infrared)
F - Hot Water Reheat Return Line.
B - Liquid Refrigerant Lines.
A - Hot Gas Refrigerant Lines (Field install factory
supplied muffler on 245A, 290A and 380A models).
1/2" NPT Male Steam
Humidifier Supply Line.
1/2" NPT Male Steam
Humidifier Return Line
Table 11
DPN000536_Rev0
Downflow air cooled (DH) piping connection sizes, inches
Air Cooled Models
60 Hz (50 Hz)
A
(AO Cu)
B
(OD Cu)
C
(NPT Male)
D
(OD Cu)
E
(NPT Male)
F
(OD Cu)
DH075A (DH075A)
5/8
1/2
1/2
5/8
1/2
5/8
DH114A (DH115A)
5/8
1/2
1/2
5/8
1/2
5/8
DH125A (DH130A)
5/8
1/2
1/2
5/8
1/2
5/8
DH199A (DH199A)
7/8
1/2
3/4
7/8
3/4
7/8
DH245A (DH245A)
1-1/8
5/8
3/4
7/8
3/4
7/8
DH290A (DH290A)
1-1/8
5/8
NA
NA
NA
NA
DH380A (DH380A)
1-1/8
5/8
NA
NA
NA
NA
23
Air Cooled Models
Figure 16 Upflow air cooled (VH) piping connections
Install field piping
through factorysupplied cover plate
(not shown for clarity). Unit
Left End
Seal around all
Panel
piping penetrations.
DPN000537 Rev0
Table 12
Factory provided piping connection sizes, inches, upflow air cooled (VH)
Air Cooled Models
50Hz
60Hz
A
OD Cu
B
OD Cu
C
NPT Female
D
OD Cu
E
NPT Female
F
OD Cu
VH-075A
VH-075A
5/8
1/2
1/2
5/8
1/2
5/8
VH-115A
VH-114A
5/8
1/2
1/2
5/8
1/2
5/8
VH-130A
VH-125A
5/8
1/2
1/2
5/8
1/2
5/8
VH-199A
VH-199A
7/8
1/2
3/4
7/8
3/4
7/8
VH-245A
VH-245A
11/8
5/8
3/4
7/8
3/4
7/8
VH-290A
VH-290A
1-1/8
5/8
NA
NA
NA
NA
VH-380A
VH-380A
1-1/8
5/8
NA
NA
NA
NA
24
Air Cooled Models
Figure 17 Outdoor air cooled 1-4 fan condenser cabinet and anchor dimensional data
Eyebolts for lifting
condenser provided on
four-fan models only
43-9/16"
(1107mm)
A
70"
(1778mm)
Height to top
37-7/8" of fan guard
43-1/8"
(962mm)
(1095mm)
18" (457mm)
Optional
disconnect
switch handle
43-3/16"
(1097mm)
B
Clearance of 36" (914.4mm) recommended
on all sides for proper operation and
component access
SL-18200-03-01
1-3/4"
(44.5mm)
1" (25.4mm)
4-1/4"
(108mm)
B
D
C
1-3/4"
(44.5mm)
37-11/16"
(957mm)
4-1/4"
(108mm)
1"
(25.4mm)
1/2" (12.7mm)
diameter anchor
bolts (typ.)
4 legs furnished for 1-,
2- and 3-fan models
6 legs furnished for
4-fan models
UNIT ANCHOR PLAN
TYPICAL FOOTPRINT
Condenser Physical data
DPN000701 Rev0
25
Air Cooled Models
Table 13
Outdoor air cooled 1-4 fan condenser physical data
Total Heat
CFM Rejection 50 Hz3 CFM
Net
(l/s)
(l/s) Weight
Model
# of
CSF/CDF1 Fans in. (mm) in. (mm) in. (mm) in. (mm) BTU/H/°F kW/°C 60 Hz2 BTU/H/°F kW/°C 50 Hz2 lb (kg)
A
B
C
D
Total Heat
Rejection 60 Hz3
-065
1
51-1/2
(1308)
44
(1118)
42
(1067)
_
1464
.772
6866
(3240)
1349
.712
5722
(2700)
295
(134)
-083L
1
51-1/2
(1308)
44
(1118)
42
(1067)
_
1655
.873
6000
(2831)
1526
.805
5000
(2359)
295
(134)
-086
1
51-1/2
(1308)
44
(1118)
42
(1067)
_
1921
1.013
6633
(3130)
1751
.924
5527
(2608)
315
(413)
-097
1
51-1/2
(1308)
44
(1118)
42
(1067)
_
2228
1.176
6322
(2983)
1995
1.053
5268
(2486)
335
(152)
-104L
1
51-1/2
(1308)
44
(1118)
42
(1067)
_
1945
1.026
5400
(2548)
1733
.914
4500
(2123)
315
(143)
-107C
1
51-1/2
(1308)
44
(1118)
42
(1067)
_
1938
1.022
6322
(2984)
1750
.923
5265
(2485)
420
(191)
-130
2
91-1/2
(2324)
84
(2134)
82
(2083)
_
2928
1.545
13732
(6480)
2698
1.423
11443
(5400)
425
(193)
-165L
2
91-1/2
(2324)
84
(2134)
82
(2083)
_
3310
1.746
12000
(5663)
3051
1.610
10000
(4719)
425
(193)
-175
2
91-1/2
(2324)
84
(2134)
82
(2083)
_
3842
2.027
13266
(6260)
3502
1.847
11055
(5217)
495
(225)
-205L
2
91-1/2
(2324)
84
(2134)
82
(2083)
_
3976
2.098
10443
(4928)
3509
1.851
8703
(4107)
495
(225)
-216C
2
91-1/2
(2324)
84
(2134)
82
(2083)
_
4324
2.281
12176
(5747)
3836
2.023
10132
(4782)
655
(297)
-217C
2
91-1/2
(2324)
84
(2134)
82
(2083)
_
4721
2.491
12644
(5967)
4204
2.218
10537
(4972)
515
(234)
-251L
3
131-1/2
(3340)
124
(3150)
122
(3099)
_
4965
2.619
18000
(8494)
4577
2.415
15000
(7078)
500
(227)
-258
3
131-1/2
(3340)
124
(3150)
122
(3099)
_
5763
3.040
19899
(9390)
5252
2.771
16582
(7825)
670
(305)
-291
3
131-1/2
(3340)
124
(3150)
122
(3099)
_
6685
3.527
18966
(8950)
5986
3.158
15805
(7458)
741
(337)
-308L
3
131-1/2
(3340)
124
(3150)
122
(3099)
_
5664
2.988
15665
(7392)
5264
2.777
13054
(6160)
670
(305)
-330L
4
171-1/2
(4356)
164
(4166)
82
(2083)
80
(2032)
6619
3.492
24000
(11326)
6103
3.220
20000
(9438)
780
(355)
-349C
3
131-1/2
(3340)
124
(3150)
122
(3099)
_
6984
3.684
17397
(8211)
6174
3.256
14532
(6859)
916
(415)
-415L
4
171-1/2
(4356)
164
(4166)
82
(2083)
80
(2032)
7779
4.104
21600
(10193)
6932
3.657
18000
(8494)
815
(370)
-480C
4
171-1/2
(4356)
164
(4166)
82
(2083)
80
(2032)
8915
4.703
25288
(11933)
7981
4.211
21073
(9944)
1025
(466)
-510C
4
171-1/2
(4356)
164
(4166)
82
(2083)
80
(2032)
10086
5.321
21687
(10234)
8763
4.623
18072
(8528)
1188
(540)
1. CSF model prefix is for single refrigeration circuit. CDF model prefix is for dual refrigeration circuits.
2. All condenser fan motors are 3/4 HP.
3. Total Heat Rejection given above is per circuit for CDF models. For CSF models double the capacity shown. The Total Heat Rejection is
for each degree differential between saturated condensing temperature and entering ambient air temperature. To calculate Total Heat
Rejection per condenser, multiply table value by temperature differential.
26
Air Cooled Models
Figure 18 Outdoor air cooled 6 and 8 fan condenser cabinet and anchor dimensional data
NOTE: Refer to
sheet 10067 Pg. 4
for connection
sizes
Recommended rigging and spreader
bars required for installation; rigging
and bars not supplied by Liebert
Location of holes and
support for rigging (typ. 4)
87-1/8"
(2213mm)
L
Height to top
of fan guard
43-1/8"
(1095mm) 37-7/8"
(962mm)
Optional
disconnect
switch
handle
Center leg
provided on
8-fan models
only
86-3/4"
(2203.5mm)
1" (25.4mm)
1-3/4"
(44.5mm)
E
C
Clearance of 36" (914.4mm) recommended
on all sides for proper operation and
component access
4-1/4"
(108mm)
1-3/4"
(44.5mm)
42"
(1067mm)
4-1/4"
(108mm)
18"
(457mm)
C
A
B
4 legs furnished for
6-fan models
6 legs furnished for
8-fan models
1"
(25.4mm)
TYPICAL FOOTPRINT
Condenser Physical data
1/2" (12.7mm) diameter
anchor bolts (typ.)
Additional legs provided on condensers
with Lee-Temp receivers
UNIT ANCHOR PLAN
Table 14
86-3/4"
(2203.5mm)
DPN000701 Rev0
Outdoor air cooled 6 and 8 fan condenser physical data
Model
# of
Fans
-616L
6
-660L
8
-830L
8
-960C
8
-1010C
8
A
B
C
E
L
in
(mm)
in
(mm)
in
(mm)
in
(mm)
in
(mm)
CFM (l/s)
60 Hz
THR 60 Hz.
BTU/hr (kw)
CFM (l/s)
50 Hz
THR 50 Hz
BTU/hr (kW)
Net
Weight
lb (kg)
124
(3150)
164
(4166)
164
(4166)
164
(4166)
164
(4166)
59
(1499)
70
(1778)
70
(1778)
70
(1778)
70
(1778)
131-1/2
(3340)
171-1/2
(4356)
171-1/2
(4356)
171-1/2
(4356)
171-1/2
(4356)
31330
(14785)
48000
(22651)
43200
(20386)
50576
(23876)
43400
(20485)
23854
(12.6)
26478
(14.0)
31114
(16.4)
35660
(18.8)
40344
(21.3)
26108
(12320)
40000
(18875)
36000
(16988)
42146
(19888)
36167
(17070)
21056
(11.2)
24412
(12.8)
27366
(14.6)
31926
(16.8)
35050
(18.5)
1380
(627)
1600
(727)
1670
(759)
2090
(950)
2640
(1198)
122
(3099)
82
(2083)
82
(2083)
82
(2083)
82
(2083)
_
80
(2032)
80
(2032)
80
(2032)
80
(2032)
THR - Total Heat Rejection, 1°F TD, for Total Condenser
THR - Total Heat Rejection, 1°C TD, for Total Condenser (50 Hz)
27
Air Cooled Models
Figure 19 Air cooled model general arrangement diagram
Condenser Coil
Schrader
Valve
Fusible
Plug
Inverted traps* on discharge and return
lines to extend above base of coil by a
minimum of 7-1/2" (190mm)
Evaporator Coil
Traps*
every 25ft.
(7.6m) of
rise
Solenoid
Valves
Liquid
Return
Expansion
Valve
Sensing
Bulb
Sight
Glass
Shutoff*
Valve
Hot Gas
Bypass
Filter
Dryer
Hot Gas
Bypass
(optional)
External
Equalizers
Cylinder
Unloaders
(optional)
Muffler
Muffler**
Hot Gas
Discharge
Service
Valves
Compressor
Single Refrigeration Circuit Shown
* Components are not supplied by
Liebert but are recommended for
proper operation and maintenance
Factory Piping
Optional Piping
Field Piping
** Components supplied by Liebert and
must be field-installed (DH/VH and DE/VE
245A, 290A and 380A models only)
DPN000525 Rev0
NOTE
Two refrigeration circuits required - Single circuit shown only for clarity
Table 15
Refrigerant control settings psi (kPa)
Model
Refrigerant Type
Low Pressure
Cut Out
Low Pressure
Cut In
High Pressure
Cut Out
Fan Speed Control
Lee-Temp
R-22
R-22
15 (103.4)
20 (137.9)
35 (241.3)
65 (448.2)
360 (2482)
360 (2482)
28
Air Cooled Models
Figure 20 Piggyback condenser cabinet and floor planning dimensional data
1 1/8"
(29mm)
E
K
H
J
D
B
R
Dime
Overall
K
Overa
ll Dim
e nsio
nsions
ns
OPTIONAL FAN
DISCHARGE
S
DISCONNECT
SWTICH
(OPTIONAL)
H
J
R
35 1/8"
(892mm)
72"
(1829mm)
FAN DISCHARGE
SHADED AREAS
INDICATE A RECOMMENDED
CLEARANCE OF 34" (864mm)
FOR COMPONENT ACCESS.
5"
(127mm)
1"
(25.4mm)
G
CONDENSER COIL INLET
AND DUCT CONNECTION
A
C
Unit Base
Unit Base
10"
(254mm)
UNIT DIMENSIONAL DATA
FAN DISCHARGE DATA
DRAIN OUTLET
OPENING
C
REAR DISCHARGE
OPTIONAL TOP DISCHARGE
F
FLOOR LEVEL
A
SL10063Page5
FLOOR CUTOUT DIMENSIONS
NOTE
A 1” (25.4mm) flange is provided on all units for duct connection to coil duct opening and fan
air discharge opening.
Table 16
Piggyback condenser dimensional data
Dimensional Data in. (mm)
Model
A
B
C
D
E
F
G
H
J
K
R
S
Shipping
Weight
lb (kg)
PB350A
72
74
31
32 1-1/8
(1829) (1880) (787) (813) (29)
33
(838)
60
(1524)
8-5/8
(219)
50-3/16 16-1/16
(1275)
(408)
13-3/16
(335)
14-11/16
(373)
1180
(535)
PB550A
72
74
31
32 1-1/8
(1829) (1880) (787) (813) (29)
33
(838)
60
(1524)
8-5/8
(219)
50-3/16 16-1/16
(1275)
(408)
13-3/16
(335)
14-11/16
(373)
1180
(535)
PB675A
72
74
31
32 1-1/8
(1829) (1880) (787) (813) (29)
33
(838)
60
(1524)
8-5/8
(219)
50-3/16 16-1/16
(1275)
(408)
13-3/16
(335)
14-11/16
(373)
1180
(535)
PB925A
97
99
33
34 3-1/8 45-1/2
85
23-5/16 50-3/16 16-1/16
(2464) (2515) (838) (864) (79) (1156) (2159) (592)
(1275)
(408)
23-1/2
(597)
14-11/16
(373)
1630
(739)
PB1100A
97
99
33
34 3-1/8 45-1/2
85
23-5/16 50-3/16 16-1/16
(2464) (2515) (838) (864) (79) (1156) (2159) (592)
(1275)
(408)
23-1/2
(597)
14-11/16
(373)
1630
(739)
PB1350A
97
99
33
34 3-1/8 45-1/2
85
16-5/16
(2464) (2515) (838) (864) (79) (1156) (2159) (421)
16-13/16
(427)
11-5/8
(295)
1630
(739)
29
63-7/8
(1622)
19-1/8
(486)
Air Cooled Models
Figure 21 Piggyback condenser piping connections
SEE
SE
E NOTE 2
SEE
SE
E NOT
NOTE
E1
SEE NOT
NOTE
E1
SEE NOT
NOTE
E2
1 13/16"
(46mm)
(46mm)
A
B
NOTES:
C
G
1 13 16"
(46mm)
(4
6mm)
1. Multiple K.O. of 1 3/8" (35mm), 1 3/4" (45mm)
and 2 1/2" (64mm) for main power supply (typ.).
2. 7/8" (22.2mm) K.O. for Lee-Temp power supply (typ.).
3. Cover plate for access of liquid line and hot gas line.
E
SEE NOT
NOTE
E3
D
3" (76m
(76mm)
m)
F
SEE
SE
E NOTE 1
1" (25m
(25mm)
m)
SEE
SE
E NOTE 2
3" (76mm)
(76mm)
E
SEE
SE
E NOT
NOTE
E3
12 5/8"
5/8
(321mm)
(321
mm)
5 1/2" (140mm)
(140mm)
SEE
SEE NOT
NOTE
E1
3 1/4"
1/4" (8
(85m
5mm)
m)
SEE
SEE NOT
NOTE
E2
3"
(76mm)
(76mm)
DRAIN OUT
DRAIN
OUTLE
LET
LOCA
LO
CATI
TION
ON
1-1/
11/4"
4" (3
(32mm)
mm) F.P.T
F.P.T.
6"
(152
(1
52mm
mm)
3"
(76mm)
(7
mm)
SEE
SE
NOTE 3
1 1/2"
(38mm)
(38mm)
Table 17
9 11/16"
11/16"
(246mm)
(246mm)
7 7/8"
(200mm)
(200mm)
8"
(203m
203mm)
m)
SL-10063Page6
Piggyback condenser piping connection dimensional data
Dimensional Data
Model
A
B
PB350A
–
–
PB550A
–
–
PB675A
–
PB925A
–
PB1100A
–
PB1350A
Table 18
2 1/2" (64
(64mm)
mm)
C
Hot Gas Line
Drain
27-1/4 (692) 1-1/2 (38) 6 (152) 9-1/8 (232) 28-3/4 (730) 2 @ 1/2 (13)
2 @ 5/8 (16)
1-1/4 (32)
27-1/4 (692) 1-1/2 (38) 6 (152) 9-1/8 (232) 28-3/4 (730) 2 @ 1/2 (13)
2 @ 5/8 (16)
1-1/4 (32)
–
27-1/4 (692) 1-1/2 (38) 6 (152) 9-1/8 (232) 28-3/4 (730) 2 @ 1/2 (13)
2 @ 7/8 (22)
1-1/4 (32)
–
27-1/4 (692) 1-1/2 (38) 6 (152) 9-1/8 (232) 28-3/4 (730) 2 @ 1/2 (13)
2 @ 7/8 (22)
1-1/4 (32)
–
27-1/4 (692) 1-1/2 (38) 6 (152) 9-1/8 (232) 28-3/4 (730) 2 @ 5/8 (16) 2 @ 1-1/8 (29) 1-1/4 (32)
9-1/4 27-1/2
29-1/2 (749)
(235) (699)
D
6 (152)
E
Connection Sizes O.D.S., inches (mm)
6 (152)
F
–
G
–
Piggyback condenser approximate refrigerant charges
Model
lb (kg) per circuit
PB350A
19 (8.6)
PB550A
18 (8.2)
PB675A
26 (11.8)
PB925A
23 (10.4)
PB1100A
36 (16.3)
PB1350A
36 (16.3)
30
Liquid Line
2 @ 5/8 (16) 2 @ 1-1/8 (29) 1-1/4 (32)
Air Cooled Models
3.4
Fan Speed Control Systems
Fan Speed Control provides an infinite number of speed variations on specially designed permanent
split-capacitor motors. The control module varies the air quantity passing over the condenser coil by
monitoring refrigerant pressure.
3.4.1
Materials Supplied
•
•
•
•
•
•
3.4.2
Built-in, pre-wired condenser control box
Air cooled condenser
Piping access cover to be reinstalled when piping is complete
Bolts – four per leg (3/8"x5/8")
Terminal block for two-wire, 24V interlock connection between unit and condenser
Condenser legs – four with 1-fan, 2-fan and 3-fan models; six with 4-fan models
Dehydration
1. Open all disconnect switches.
2. Pull all fuses except transformer fuses. On units supplied with circuit breakers, open all breakers
except for the transformer.
3. Turn disconnects ON and jumper Fan Safety Switch between Common and Normal Open.
4. To energize the solenoid valves, use manual override jumpers (on SM). On AM and AG, set the
temperature set point (see operation manual) to 60°F (15°C) to ensure that solenoid valves are
open during the dehydration procedure.
5. Connect refrigeration gauges to the suction and discharge service valves of compressors 1 & 2.
6. Open all service valves.
Connect refrigerant gauges to both the suction and discharge service valves of the compressors. Starting with circuit #1, open the service valves and place 150 PSIG (1034 kPa) of dry nitrogen with a
tracer of Freon. Check system for leaks.
With pressure in circuit: #1, open the service valves in circuit #2. If pressure increases in circuit #2,
the system is cross-circuited and must be rechecked for proper piping. If there is no pressure increase,
repeat leak check procedure for circuit #2.
After completion of leak testing, release the test pressure and pull a vacuum on the system. Leave
this vacuum for approximately 4 hours. Check the pressure to make sure that it has not increased. If
there is no change in pressure, pull another vacuum to 250 microns or less. Recheck the pressure
after two hours. After completion of this step, fill the circuits with Freon vapor until suction and discharge pressures have equalized.
3.4.3
Charging
Remove the reheat and humidifier fuses (or open circuit breakers). Remove all shipping blocks from
the compressors and insure that all operational components are clear of debris. Turn the disconnect
on and check the evaporator fan for proper rotation. Set the temperature set point (see Operation
Manual) to 60°F (15°C) to ensure that solenoid valves are open during the charging procedure. Connect the refrigerant gauge charging hose to the drum of refrigerant and purge the hoses of non-condensables. Add refrigerant vapor to the suction side of the compressor to eliminate short-cycling. The
low-pressure switch may be manually energized to expedite charging.
As head pressure builds the condenser fan will start rotating. The fan will become fully energized
when sufficient head pressure is developed. Charge the unit until the liquid line sight glasses become
clear. Watch the sight glasses for a period of 10 minutes to insure that no bubbles reappear. At this
point, add additional refrigerant to the circuit so that 5-10°F (3-5°C) subcooling is obtained in each
liquid line.
31
Air Cooled Models
Table 19
Indoor unit approximate refrigerant charge lb (kg.) R–22
Model 60 Hz (50 Hz)
Refrigerant
Charge/Circuit
75A
4.0 (1.8)
114A (115A)
5.0 (2.3)
125A (130A)
5.0 (2.3)
199A
6.0 (2.7)
245A
7.0 (3.2)
290A
7.0 (3.2)
380A
8.0 (3.6)
Table 20
Outdoor condenser approximate refrigerant charge lb (kg) per circuit
Model
Fan Speed
Control
Lee-Temp
(Includes Receiver)
097
108
130
5 (2.3)
6 (2.7)
5 (2.3)
27 (12.3)
33 (15.0)
27 (12.3)
104L
175
165L
205L
216
291
308L
349
408
415L
451
480C
488
510C
580
4 (1.8)
7 (3.2)
5 (2.3)
7 (3.2)
12 (5.4)
15 (6.8)
11 (5.0)
22 (10.0)
20 (9.1)
15 (6.8)
25 (11.3)
20 (9.1)
30 (13.6)
30 (13.6)
30 (13.6)
21 (9.5)
38 (17.2)
27 (12.3)
38 (17.2)
64 (29.0)
75 (34.0)
58 (26.3)
113 (51.3)
101 (45.8)
75 (34.0)
124 (56.3)
101 (45.8)
149 (67.6)
149 (67.6)
150 (68.0)
820
830L
39 (17.7)
30 (13.6)
N/A
149 (67.6)
Table 21
Liquid line charge lb/10 ft. (kg/.3m) R–22
Line Size, OD Cu
1/2”
5/8”
7/8”
1-1/8”
1-3/8”
Total Charge per Circuit.
(There are two circuits per system)
Table 22
Charge
.73 (.33)
1.17 (.52)
2.44 (1.09)
4.16 (1.86)
6.33 (2.83)
= Unit Charge
+ Condenser Charge
+ Liquid Line Charge
Refrigerant control settings for air cooled units psi (kPa)
Model
Refrigerant
Type
Low Pressure
Cut Out
Low Pressure
Cut In
High Pressure
Cut Out
Fan Speed Control
R-22
15 (103.4)
35 (241.3)
360 (2482)
Lee-Temp
R-22
20 (137.9)
65 (448.2)
360 (2482)
32
Air Cooled Models
3.5
Lee-Temp/Flood Back Head Pressure Control Systems
The Lee-Temp system consists of a modulating type head pressure control valve and insulated receivers with heater pads to ensure operation at ambient temperatures as low as -30°F (-34.4°C).
3.5.1
Piping
Be sure to install the valve with the refrigerant flow in the proper direction. When soldering or brazing the valves, it is very important that the internal parts be protected by wrapping the valve with a
damp cloth to keep the valve temperature below 250°F (121°C).
3.5.2
Materials Supplied
•
•
•
•
•
•
Built-in, pre-wired condenser control box
Air cooled condenser
Piping access cover to be reinstalled when piping is complete
Bolts – four per leg (3/8"x5/8")
Terminal block for two-wire, 24V interlock connection between the unit and the condenser
Condenser legs: four on one-fan models, six on two- and three-fan models, and eight on four-fan
models
• Lee-Temp system:
• Insulated storage receiver – one per circuit
• Head pressure control valve with integral check valve – one per circuit
• Adapter assembly – one per circuit
• Rotalock valve – one per circuit
• Pressure relief valve – one per circuit
• Liquid level sight glass – two per circuit
• Check valve – one per circuit.
• Bolts – six per receiver (3/8" x 1")
NOTE
Lee-Temp heater pads require a separate, continuous electrical source of
either 115 VAC or 200/208/230 VAC.
3.5.3
Dehydration
1. Open all disconnect switches.
2. Pull all fuses except transformer fuses. On units supplied with circuit breakers, open all breakers
except for the transformer.
3. Jumper Fan Safety Switch between Common and Normal Open. Turn disconnects ON.
4. Use the manual override switches to energize the solenoid valves.
5. Connect refrigeration gauges to the suction and discharge service valves of compressors 1 & 2.
6. Open all service valves.
7. Charge circuit #1 to 150 psig (1034 kPa) with dry nitrogen containing a tracer of Freon.
8. Check for pressure increase in circuit #2. This would indicate that the refrigeration circuits are
cross-circuited and must be re-piped.
9. If there is no pressure increase, charge circuit #2 to 150 psig (1034 kPa) with dry nitrogen
containing a tracer of Freon and leak-test both circuits.
10. After completion of leak testing, release test pressure and pull a vacuum on both circuits.
11. After 4 hours, check gauge readings and, if they have not changed, purge with Freon.
12. Pull a second and third vacuum of 250 microns (29.84 in. Hg), leave for 2 hours and recheck
gauges.
33
Air Cooled Models
3.5.4
Charging
1. Make sure unit is OFF and that jumper is removed on Fan Safety Switch.
2. Connect a set of manifold gauges to the refrigerant drum and to the receiver at the rotalock valve.
Purge the hoses.
3. Open the rotalock valve and fill the receiver with liquid refrigerant per Table 26.
4. Close the valve and disconnect gauges.
5. Start the compressor and recheck the refrigerant level. If the level has dropped, recharge with
vapor through the suction port.
6. Replace all fuses (or close circuit breakers) except reheat and humidifier.
7. Connect refrigerant charging hose to suction port of compressors and purge with Freon.
8. To energize the solenoid valves, use manual override jumpers (on SM) or test outputs (on AM and
AG).
9. Charge with vapor until the refrigerant level is in accordance with 3.5.5 - Refrigerant Level.
3.5.5
Refrigerant Level
On each receiver at the condenser are two refrigerant-level sight glasses. Refrigerant level will vary
with outside temperature.
Check refrigerant level after the unit has been on for at least 15 minutes.
40°F (4.5°C) and below
Bottom sight glass is 3/4 full
40°F to 60°C (4.5°C to 15.5°C)
Bottom sight glass is full
60°F (15.5°C) and above
Top sight glass is 3/4 full
Figure 22 Lee-Temp control condenser
Entering Hot Gas Line (typ)
Returning Liquid Gas Line (typ)
Lee-Temp Receiver Tank
SL-10061-6
NOTE
The following materials are supplied by Liebert for each circuit (shipped loose with condenser)
for field installation: insulated Lee-Temp storage tank, head pressure control valve, check
valve, rotalock valve, two sight glasses and a pressure relief valve. All other piping to be
supplied and installed by others.
34
Air Cooled Models
Figure 23 Lee-Temp control typical general arrangement diagram
Condenser Coil
Inverted traps* on discharge and
return lines to extend above
base of coil by a minimum
of 7-1/2" (190mm)
Piping Assembly**
Rotalock Valve**
Check
Valve
Head Pressure
Control With
Integral Check
Valve
1/4" (6.4mm)
Pressure
Relief Valve**
Lee-Temp
Receiver
Sight Glass
Evaporator Coil
Liquid Return
from Condenser
Traps* every
25’ (7.6m) of rise on
hot gas line only
Expansion Valve
Solenoid
Valves
Sensing Bulb
Shutoff*
Valve
Sight
Glass
External Equalizers
Liquid
Return
Service
Valves
Filter Dryer
Hot Gas
Bypass
(optional)
Muffler
Cylinder
Unloaders
(optional)
Compressor
Muffler***
Single circuit shown
Hot Gas
Discharge
Factory Piping
Optional Piping
Field Piping
* Components are not supplied by
Liebert but are recommended for
proper circuit operation and maintenance
** Components supplied
by Liebert and must be
field-installed
35
*** Components supplied
by Liebert and must be
field-installed (DH/VH and
DE/VE 245A, 290A and
DPN00680 Rev0
380A models only)
Glycol Cooled/GLYCOOL™ Models
4.0
GLYCOL COOLED/GLYCOOL™ MODELS
4.1
Drycooler Location
4.1.1
Outdoor Prop Fan Models
The drycooler should be located for maximum security and maintenance accessibility. Avoid groundlevel sites with public access or areas that contribute to heavy snow or ice accumulations. To assure
adequate air supply, it is recommended that drycoolers be located in a clean air area, away from loose
dirt and foreign matter that may clog the coil. In addition, drycoolers should not be located in the
vicinity of steam, hot air or fume exhausts. Also, drycoolers should not be located closer than 3 feet (1
meter) from a wall, obstruction or adjacent unit.
4.1.2
Indoor Piggyback Models
The Piggyback drycooler can be located directly behind the Deluxe unit or in a separate remote indoor
location. It may be placed directly against an outside wall, with the proper openings cut in the wall for
entering and leaving air. If it cannot be located near a wall, the unit may be ducted to the outside.
Proper grills/screens are required on the outside wall.
4.2
Drycooler Installation
For roof installation, mount drycoolers on steel supports in accordance with local codes. To minimize
sound and vibration transmission, mount steel supports across load bearing walls. For ground installation, a concrete pad will provide adequate support. Drycooler legs have mounting holes for securing
the drycooler to steel supports or concrete pad.
4.3
Electrical Connections
4.3.1
High Voltage
High voltage electrical service is required for all drycoolers at the location of the drycooler. This power
supply does not have to be the same voltage as the indoor unit. This separate power source may be
208, 230, 460 or 575 Volt 60 Hertz; or 200, 230 or 400 Volt 50 Hertz. The disconnect switch is factory
supplied and mounted in the electric panel.
4.3.2
Low Voltage
A control interlock between the drycooler and the indoor unit is required and is connected between 70
&71 on the wire raceway in the compressor compartment of the indoor unit and the pump and drycooler control box of the drycooler.
4.3.3
Pump And Drycooler
All wiring to the pump and drycooler from the control box should be done in accordance with the electrical schematic on the inside lid of the drycooler control box and with local and national codes (on
Piggyback Models, the pump is located within the drycooler).
4.4
Glycol Piping
Manual shut-off valves should be installed at the supply and return line to each indoor unit and drycooler. This will provide for routine service or emergency isolation of the unit.
To provide for the emergency of water leaks and the consequences of subfloor flooding, floor drains
should be provided with wet traps or a water detection system such as a Liqui-Tect that should be
installed near the base of the unit or below the elevated floor.
The temperature of the glycol supplied by the drycooler will determine whether the glycol supply and
return lines should be insulated to prevent condensation.
36
Glycol Cooled/GLYCOOL™ Models
Table 23
Room dew point temperatures °F (°C)
Dry Bulb
Wet Bulb
Relative Humidity
Dew Point
70 (21.1)
57.2 (14.0)
45
48.9 (8.9)
70 (21.1)
58.5 (14.7)
50
50.5 (10.3)
72 (22.2)
58.9 (14.9)
45
50.0 (10.0)
72 (22.2)
60.0 (15.5)
50
52.4 (11.3)
75 (23.8)
61.2 (16.2)
45
52.4 (11.3)
75 (23.8)
62.5 (16.9)
50
55.0 (12.7)
*Minimum glycol temperature before condensation will occur.
Table 24
Glycol concentration
% Glycol by
Volume
0
10
20
30
40
50
Freezing Point °F (°C)
32 (0)
25 (-3.9)
16 (-8.9)
5 (-15.0)
-10 (-23.3)
-32 (-35.5)
Apparent specific
Gravity @ 50°F (10°C)
1.000
1.014
1.028
1.042
1.057
1.071
Table 25
Refrigerant control settings for glycol cooled units—psi (kPa)
Refrigerant Type
Low Pressure Cut Out
Low Pressure Cut In
High Pressure Cut Out
R–22
20 (137.9)
65 (448.2)
360 (2482)
Table 26
Deluxe glycol volume approximate gal. (l) max
GLYCOOL
Model
(50 Hz)
Glycol
Cooled
Upflow
Downflow
—72G
—110G/(111G)
—116G/(121G)
—192G
—240G
—265G
—363G
2.0 (7.5)
2.0 (7.5)
2.5 (9.5)
4.5 (17.0)
5.5 (21.0)
5.5 (21.0)
6.5 (24.6)
9.0 (34.0)
9.0 (34.0)
10.0 (38.0)
14.0 (53.0)
15.0 (57.0)
–
18.0 (68.1)
8.5 (32.0)
8.5 (32.0)
10.0 (38.0)
13.5 (51.0)
15.0 (57.0)
–
18.0 (68.1)
Table 27
Volume in standard Type L copper piping
Diameter (in.)
Volume
Outside
Inside
gal./ft.
l/m
1/2
5/8
3/4
7/8
1-1/8
1-3/8
1-5/8
2-1/8
0.123
0.545
0.666
0.785
1.025
1.265
1.505
1.985
0.008
0.012
0.018
0.025
0.043
0.065
0.092
0.161
0.01
0.15
0.22
0.31
0.53
0.81
1.15
2.00
2-5/8
3-1/8
3-5/8
4-1/8
2.465
2.945
3.425
3.905
0.248
0.354
0.479
0.622
3.08
4.40
5.95
7.73
37
Glycol Cooled/GLYCOOL™ Models
Figure 24 Downflow glycol cooled (DH) piping connections
MONITORING
PANEL
NOTE: Install all piping
per local codes.
C - Steam Reheat Supply Line
D - Hot Water Reheat Supply Line.
A - Glycol Return Line.
3/4" NPT Condensate Drain.
Field pitch a min. of
1/8" (3.2mm) per ft. (305mm).
Do not install an external trap.
E - Steam Reheat Return Line (Field
install factory supplied steam
trap with vacuum breaker).
F - Hot Water Reheat Return Line.
1/4" OD CU Humidifier Supply Line
(Steam Gen./Infrared)
1/2" NPT Male Steam
Humidifier Supply Line.
B - Glycol Supply Line.
1/2" NPT Male Steam
Humidifier Return Line.
Table 28
DPN000572_Rev0
Downflow glycol cooled (DH) piping connection sizes, inches
Glycol Cooled Models
60 Hz (50 Hz)
A
(OD CU)
B
(OD CU)
C
(NPT Male)
D
(OD CU)
E
(NPT Male)
F
(OD CU)
1-5/8
1-5/8
1/2
5/8
1/2
5/8
3/4
7/8
3/4
7/8
2-1/8
2-1/8
NA
NA
NA
NA
DH072G (DH072G)
DH110G (DH111G)
DH116G (DH121G)
DH192G (DH192G)
DH240G (DH240G)
DH265G (DH265G)
DH363G (DH363G)
38
Glycol Cooled/GLYCOOL™ Models
Figure 25 Upflow glycol cooled (VH) piping connections
Install field
piping through
factory-supplied
cover plate (not shown Unit
for clarity). Seal around Left
all piping penetrations. End Panel
Table 29
DPN00573 Rev0
Factory-provided piping connection sizes, inches, upflow glycol cooled (VH)
Glycol Cooled Models
50 Hz
60 Hz
A
OD Cu
B
OD Cu
C
NPT Female
D
OD Cu
E
NPT Female
F
OD Cu
VH-072G
VH-111G
VH-121G
VH-192G
VH-240G
VH-265G
VH-363G
VH-072G
VH-110G
VH-116G
VH-192G
VH-240G
VH-265G
VH-363G
1-5/8
1-5/8
1-5/8
2-1/8
2-1/8
2-1/8
2-1/8
1-5/8
1-5/8
1-5/8
2-1/8
2-1/8
2-1/8
2-1/8
1/2
1/2
1/2
3/4
3/4
NA
NA
5/8
5/8
5/8
7/8
7/8
NA
NA
1/2
1/2
1/2
3/4
3/4
NA
NA
5/8
5/8
5/8
7/8
7/8
NA
NA
39
Glycol Cooled/GLYCOOL™ Models
Figure 26 Downflow GLYCOOL™ cooled (DE) piping connections
MONITORING
PANEL
NOTE: Install all piping
per local codes.
A - Glycol Return Line.
3/4" NPT Condensate Drain.
Field pitch a min. of
1/8" (3.2mm) per ft. (305mm).
Do not install an external trap.
1/4" OD CU Humidifier Supply Line
Steam Gen./Infrared)
B - Glycol Supply Line.
Table 30
DPN000588_Rev0
Downflow GLYCOOL (DE) piping connection sizes, inches
GLYCOOL Models
60 Hz (50 Hz)
A
(OD CU)
B
(OD CU)
1-5/8
1-5/8
2-1/8
2-1/8
DE072G (DE072G)
DE110G (DE111G)
DE116G (DE121G)
DE192G (DE192G)
DE240G (DE240G)
DE363G (DE363G)
40
Glycol Cooled/GLYCOOL™ Models
Figure 27 Upflow GLYCOOL™ cooled (VE) piping connections
UNIT CONNECTION LOCATIONS
Piping stubbed out inside unit end compartment for field
connection through 2 3/8" x 16" (60.3 x 406mm)
opening as shown. Piping is recessed inside the unit and
not flush as indicated. Piping may also exit through bottom
of end compartment by field cutting an opening in a
suitable location (except bottom return air units).
1" (25.4mm) REAR PANEL
7/8"
(22.2mm)
2 3/8"
(60.3mm)
A - Glycol Supply Line.
B - Glycol Return Line.
1/4" OD CU Humidifier
Water Supply Line.
16"
(406mm)
3/4" NPT Condensate Drain.
Field pitch a min. of 1/8"
(3.2mm) per ft. (305mm). Do
not install an external trap.
3 3/8"
(85mm)
NOTE: Install all piping
per local codes.
UNIT LEFT
END PANEL
Table 31
DPN000588_Rev0
Upflow GLYCOOL (VE) piping connection sizes, inches
GLYCOOL Models
60 Hz (50 Hz)
A
(OD Cu)
B
(OD Cu)
1-5/8
1-5/8
2-1/8
2-1/8
VE072G (VE072G)
VE110G (VE111G)
VE116G (VE121G)
VE192G (VE192G)
VE240G (VE240G)
VE363G (VE363G)
41
Glycol Cooled/GLYCOOL™ Models
Figure 28 1-4 fan drycooler cabinet and anchor dimensional data
Eyebolts for lifting condenser
provided on four-fan models only
Inlet Connection
(upper header)
A
70"
Outlet
(1778mm)
43-9/16"
(1107mm)
Connection
(lower
header)
Height to
top of fan
guard
43-1/8"
37-7/8"
(962mm) (1095mm)
4"
(101.6mm)
Disconnect
Switch
Handle
43-3/16"
(1097mm)
18"
(457mm)
Clearance of 36" (914.4mm)
recommended on all sides
for proper operation and
component access
B
EXPANSION TANK
11.5"
(292.1mm)
(GLYCOOL CSU3000 units
supplied with compression tank)
1" (25.4mm)
1-3/4"
(44.5mm)
32"
)
(812.8mm
9"
(228.6mm)
4-1/4"
(108mm)
B
C
1-3/4"
(44.5mm)
4-1/4"
(108mm)
1"
(25.4mm)
37-11/16"
(957mm)
1/2" (12.7mm)
diameter anchor
bolts (typ.)
D
4 legs furnished for 1-,
2- and 3-fan models
6 legs furnished for
4-fan models
TYPICAL FOOTPRINT
Condenser Physical data
UNIT ANCHOR PLAN
Table 32
Glycol pump data
Pump
Hp
Hz
1-1/2
60
2
60
3
60
5
60
1
50
2
50
3
50
Pump Suction
Connection
in.
Pump Discharge
Connection
in.
1-1/4
3/4
1-1/2
1
1-1/4
1-1/4
3/4
1-1/2
1-1/4
Note: Connection sizes apply to primary pump supplier.
42
DPN000274 Rev0
Glycol Cooled/GLYCOOL™ Models
Table 33
1-4 fan drycooler physical data
# of
(Notes 2,3,4) Fans
Model
A
B
C
D
in.
(mm)
in.
(mm)
in.
(mm)
in.
(mm)
Piping
Connection
Sizes
CFM
(l/s)
60 Hz1
CFM
(l/s)
50 Hz1
Internal
Volume
gal. (l)
Net Weight
lb (kg)
Inlet
in. (mm)
Outlet
in. (mm)
-033
1
51-1/2
(1308)
44
(1118)
42
(1067)
_
7200
(3398)
6000
(2932)
1.2
(4.6)
390
(177)
3/4
(19.1)
3/4
(19.1)
-069
1
51-1/2
(1308)
44
(1118)
42
(1067)
_
6866
(3240)
5722
(2700)
2.4
(9.2)
410
(186)
1-1/4
(31.8)
1-1/4
(31.8)
-092
1
51-1/2
(1308)
44
(1118)
42
(1067)
_
6633
(3130)
5527
(2609)
3.7
(13.9)
430
(195)
1-1/2
(38.1)
1-1/2
(38.1)
-109
1
51-1/2
(1308)
44
(1118)
42
(1067)
_
6322
(2984)
5268
(2486)
4.9
(18.6)
450
(204)
2
(50.8)
2
(50.8)
-112
1
51-1/2
(1308)
44
(1118)
42
(1067)
_
6088
(2873)
5074
(2394)
5.8
(22.0)
470
(213)
2
(50.8)
2
(50.8)
-139
2
91-1/2
(2324)
84
(2134)
82
(2083)
_
13732
(6481)
11443
(5401)
4.8
(18.2)
565
(256)
2
(50.8)
2
(50.8)
-174
2
91-1/2
(2324)
84
(2134)
82
(2083)
_
13265
(6261)
11054
(5217)
6.9
(26.2)
605
(274)
2
(50.8)
2
(50.8)
-197
2
91-1/2
(2324)
84
(2134)
82
(2083)
_
12645
(5968)
10535
(4973)
9
(34)
645
(293)
2
(50.8)
2
(50.8)
-225
2
91-1/2
(2324)
84
(2134)
82
(2083)
_
12177
(5748)
10147
(4789)
11.1
(42.1)
685
(310)
2
(50.8)
2
(50.8)
-260
3
131-1/2
(3340)
124
(3150)
122
(3099)
_
19898
(9392)
16582
(7827)
10.0
(37.8)
826
(375)
2
(50.8)
2
(50.8)
-310
3
131-1/2
(3340)
124
(3150)
122
(3099)
_
18965
(8951)
15804
(7459)
13.1
(50.0)
886
(402)
2
(50.8)
2
(50.8)
-350
3
131-1/2
(3340)
124
(3150)
122
(3099)
_
17398
(8218)
14499
(6843)
19.4
(65.9)
946 (429)
2
(50.8)
2
(50.8)
-352
4
171-1/2
(4356)
164
(4166)
82
(2083)
80
(2032)
24800
(11705)
20667
(9755)
13.1
(49.6)
1040
(471)
2
(50.8)
2
(50.8)
-419
4
171-1/2
(4356)
164
(4166)
82
(2083)
80
(2032)
23650
(11163)
19708
(9302)
17.4
(65.9)
1120
(508)
2
(50.8)
2
(50.8)
-466
4
171-1/2
(4356)
164
(4166)
82
(2083)
80
(2032)
22770
(10747)
18975
(8956)
22.0
(83.3)
1150
(522)
2-1/2
(63.5)
2-1/2
(63.5)
-491
4
171-1/2
(4356)
164
(4166)
82
(2083)
80
(2032)
21700
(10242)
18083
(8535)
26.3
(99.6)
1200
(544)
2-1/2
(63.5)
2-1/2
(63.5)
1. All drycooler fan motors are 3/4 HP.
2. DSO model prefix indicates control section in drycooler includes controls for a single pump package. DDO model prefix indicates control
section in drycooler includes controls for a dual pump package. DSF model prefix indicates control section in drycooler includes controls
for a single pump package on a fan speed control drycooler.
3. DNT prefix indicates a single circuit with fan cycling but no pump controls.
4. DNC prefix indicates a single circuit with no fan or pump controls.
43
Glycol Cooled/GLYCOOL™ Models
Figure 29 6- and 8-fan drycooler cabinet and anchor dimensional data
Recommended rigging and
spreader bars required for
installation; rigging and bars
not supplied by Liebert
NOTE: Refer to sheet 10067 Pg. 4
for connection sizes
Location of holes and
support for rigging (typ. 4)
87-1/8"
(2213mm)
L
Height to top
of fan guard
43-1/8"
37-7/8"
(1095mm) (962mm)
Optional
disconnect
switch
handle
86-3/4"
(2203.5mm)
1-3/4"
(44.5mm)
1" (25.4mm)
Center leg
provided on
8-fan models
only
E
18"
(457mm)
Clearance of 36" (914.4mm)
recommended on all sides for proper
operation and component access
4-1/4"
(108mm)
1-3/4"
(44.5mm)
UNIT ANCHOR PLAN
C
4-1/4"
(108mm)
42"
(1067mm)
1"
(25.4mm)
A
B
4 legs furnished for
6-fan models
6 legs furnished for
8-fan models
TYPICAL FOOTPRINT
Condenser Physical data
86-3/4"
(2203.5mm)
1/2" (12.7mm) diameter
anchor bolts (typ.)
Additional legs provided on condensers
with Lee-Temp receivers
DPN000701 Rev0
Table 34
6- and 8-fan drycooler physical data
A
B
C
E
L
# of
Model Fans in (mm) in (mm) in (mm) in (mm) in (mm)
122
124
59
131-1/2
-620
6
_
(3099)
(3150)
(1499)
(3340)
122
124
59
131-1/2
-650
6
_
(3099)
(3150)
(1499)
(3340)
122
124
59
131-1/2
-700
6
_
(3099)
(3150)
(1499)
(3340)
82
80
164
70
171-1/2
-790
8
(2083)
(2032)
(4166)
(1778)
(4356)
82
80
164
70
171-1/2
-880
8
(2083)
(2032)
(4166)
(1778)
(4356)
82
80
164
70
171-1/2
-940
8
(2083)
(2032)
(4166)
(1778)
(4356)
CFM
(l/s)
60 Hz
37900
(17889)
36500
(17228)
34800
(16426)
47300
(22326)
45500
(21476)
43400
(20485)
44
Coil
CFM Internal
(l/s)
Volume Net Weight
50 Hz
gal. (l)
lb (kg)
31600
27.0
1940
(14915) (102.2)
(880)
30400
33.0
2000
(14349) (124.9)
(907.2)
29000
40.0
2060
(13688) (151.4)
(934.4)
39400
35.0
2550
(18597) (132.5)
(1157)
37900
44.0
2730
(17889) (166.5)
(1238.3)
36200
52.0
2910
(17086) (196.8)
(1320)
Piping Connection
Sizes
Inlet
Outlet
in. (mm) in. (mm)
2-1/8
2-1/8
(54)
(54)
2-1/8
2-1/8
(54)
(54)
2-1/8
2-1/8
(54)
(54)
2-1/8
2-1/8
(54)
(54)
2-1/8
2-1/8
(54)
(54)
2-1/8
2-1/8
(54)
(54)
Glycol Cooled/GLYCOOL™ Models
4.5
Preparation of Glycol Solutions
Typical ethylene glycol manufacturers and suppliers are Union Carbide (Ucartherm) or Dow Chemical Company (Dowtherm SR-1). These ethylene glycols are supplied with an inhibitor and do not contain an anti-leak formula.
NOTE
For glycol solution preparation and periodic testing, follow manufacturer's
recommendations. Do not mix products of different manufacturers.
!
CAUTION
Automotive antifreeze is unacceptable and must NOT be used.
Commercial ethylene glycol, when pure, is generally less corrosive to the common metals of construction than water itself. Aqueous solutions of these glycols, however, assume the corrosivity of the
water from which they are prepared and may become increasingly corrosive with use if not properly
inhibited.
There are two basic types of corrosion inhibition; they are classified as corrosion inhibitors or environmental stabilizers. The corrosion inhibitors function by forming a surface barrier that protects the
metals from attack. Environmental stabilizers, while not corrosion inhibitors in the strict sense of the
word, decrease corrosion by stabilizing or favorably altering the overall environment. An alkaline
buffer, such as borax, is a simple example, since its prime purpose is to maintain an alkaline condition (pH above 7).
The quality of the water used for dilution must be considered because water may contain corrosive
elements which reduce the effectiveness of the inhibited formulation. Preferably, surface water that is
classified as soft (low in chloride and sulfate ion content—less than 100 parts per million each) should
be used. Before an inhibited glycol solution is charged into a new or old system, residual contaminants such as sludge, rust, brine deposits, oil, etc., should be flushed out as completely as possible.
Avoid the use of strong acid cleaners. However, if they are required, inhibited acids should be considered. In any event, assure that the cleaning agent is completely removed before charging with glycol.
Contact Liebert Customer Service and Support for additional recommendations.
!
CAUTION
Galvanized pipe must not be used in glycol systems.
45
Glycol Cooled/GLYCOOL™ Models
Figure 30 Glycol general arrangement
Expansion Tank
field-installed at
highest point in
system
Drycooler
Electric Box
Fill*
Optional Dual
Pump System
Shown
Unions*
Drycooler
Coil
Pump
Housing
Check Valves * (dual
Fluid
pump systems only)
Unions* Return to
Gate Valves*
Pump
Fluid
Evaporator
Pressure Ports*
Supply
Coil
Hose
from
Aquastat
Bibs*
Pump
Sensing
Flow Switch supplied
Air Vents* Bulbs
Expansion
with dual pump systems
at top of
Valve
risers
Solenoid
Valves
Flow Regulating
Valve*
Sight
Glass
Sensing
Bulb
Filter
Dryer
Hot Gas
Bypass
Valve
Hot Gas
Bypass
(optional)
Glycol Coolant
Circuit (one
required per
unit)
Compressor
Solenoid Valve
provided with
optional hot gas
reheat
Shutoff Valve
Relief
Valve
Fluid
Supply
to Unit
Fluid
Return
from Unit
External
Equalizers Cylinder
Unloader
(optional)
Service
Valves
Muffler
Liquid
Return
Hot Gas
Reheat
Coil
(optional)
Bypass
Valve
Condenser
Condenser
Check
Valve
Bypass
Valve
Shutoff
Valves*
To 2nd
refrigeration
unit
2-Way Glycol
Regulating
Valve
2-Way Glycol
Regulating
Valve
Hose Bibs*
3-Way Glycol
Regulating
Valve (optional)
Factory Piping
Optional Piping
Field Piping
* Components are not supplied by Liebert but
are recommended for proper circuit
operation and maintenance
DPN000561 Rev0
46
Glycol Cooled/GLYCOOL™ Models
Figure 31 GLYCOOL™ general arrangement
Expansion Tank
field-installed at
highest point in
system
Drycooler
Electric Box
Glycol
Pumps
Unions*
Drycooler Coil
Optional Dual
Pump System
Shown
Fill*
Pump
Housing
Gate Valves*
Check Valves * (dual
pump systems only)
Fluid
Return
Flow Switch to Pump
supplied with
dual pump Fluid Supply
from Pump
systems
Hose
Bibs*
Aquastat
Sensing
Air Vents* Bulbs
at top of
risers
Econ-O-Coil
Pressure
Ports*
Valve
Actuator
Econ-O-Cycle
Comparator
Flow
Regulating
Valve*
Evaporator
Coil
Expansion
Valve
Solenoid
Valves
3-Way Sight
Chilled Glass
Glycol
Valve
Hot Gas
Bypass
Valve
Filter
Dryer
Econ-O-Coil Liquid
Circuit
Return
(one supplied
per unit)
Glycol Coolant
Circuit
(one required
per unit)
Fluid
Return
from Unit
Hot Gas
Reheat
Coil
(optional)
Hot Gas
Bypass
(optional)
Muffler
Sensing
Bulb
External
Equalizers
Cylinder
Unloader
(optional)
Service
Valves
Compressor
Shutoff
Valve
Relief
Valve
Condenser
3-Way Glycol
Regulating
Valve (optional)
Check
Valve
Fluid
Supply
to Unit
Solenoid Valve
provided with
optional hot
gas reheat
To 2nd
refrigeration unit
Shutoff
Valves*
3-Way Glycol
Regulating
Valve
Factory Piping
Optional Piping
Field Piping
* Components are not supplied by Liebert
but are recommended for proper circuit
operation and maintenance
Hose Bibs*
DPN000579 Rev0
47
Water Cooled Models
5.0
WATER COOLED MODELS
5.1
Piping Considerations
Manual shut-off valves should be installed at the supply and return lines of each unit. This will provide for routine maintenance or emergency isolation of the unit.
When the water source for the condenser is of poor quality, it is good practice to provide cleanable filters in the supply line. These filters will trap the particles in the water supply and extend the service
life of the water-cooled condenser.
To provide for the emergency of water leaks and the consequences of sub-floor flooding, floor drains
should be provided with wet traps or a water detection system such as a Liqui-Tect sensor that is
installed near the base of the unit or below the elevated floor.
5.2
Condenser
The condenser is designed to operate in conjunction with either a cooling tower or city water.
5.3
Water Regulating Valve
Water regulating valves automatically open on refrigerant pressure increase and close on pressure
decrease.
To adjust the head pressure, attach refrigeration gauges to the compressor discharge and suction service valves. Raise the head pressure by turning the adjusting screw counterclockwise. Lower the head
pressure by turning the adjusting screw clockwise. Allow enough time between changes for the system to stabilize.
5.3.1
Testing Valve Function
When the refrigeration system has been off for approximately 10-15 minutes, the water flow should
stop.
Should the water continue to flow, the valve is either improperly adjusted or the pressure sensing
capillary is not connected properly to the condenser.
5.3.2
Manual Flushing
The valve may be flushed by inserting a screwdriver or similar tool under the two sides of the main
spring and lifting. This action will open the valve seat and flush any dirt particles from the seat.
Table 35
Refrigerant control settings for water cooled units—psi (kPa)
Refrigerant
Type
Low
Pressure
Cut Out
Low
Pressure
Cut In
High
Pressure
Cut Out
R–22
20 (137.9)
65 (448.2)
360 (2482)
48
Water Cooled Models
Figure 32 Water cooled general arrangement
Evaporator Coil
Sensing
Bulb
Single Refrigeration Circuit Shown
Solenoid
Valves
Expansion
Valve
Sight
Glass
Filter
Dryer
Shutoff
Valve
Water Coolant
Circuit
(one required
per unit)
External
Equalizers
Cylinder
Unloader
(optional)
Hot Gas
Bypass
Valve
Hot Gas
Bypass
(optional)
Hot Gas
Reheat Coil
(optional on
downflow
units only)
Muffler
Service
Valves
Liquid
Return
Compressor
Relief
Valve
Fluid
Fluid
Supply
Return
from Unit to Unit
Shutoff
Valves*
Bypass
Valves
(optional)
Condenser
Check
Valve
Solenoid Valve
provided with
optional hot
gas reheat
To 2nd
refrigeration
unit
2-way Water
Regulating
Valves
Condenser
Hose Bibs*
Factory Piping
3-way Water
Regulating Valve
(optional)
Optional Piping
Field Piping
49
* Components are not supplied by
Liebert but are recommended for
proper circuit operation and
maintenance
DPN000543 Rev0
Water Cooled Models
Figure 33 Downflow water cooled (DH) piping connections
MONITORING
PANEL
NOTE: Install all piping
per local codes.
C - Steam Reheat Supply Line
D - Hot Water Reheat Supply Line.
E - Steam Reheat Return Line
(Field-install factory-supplied
steam trap with vacuum breaker)
A - Condenser Water Return Line.
3/4" NPT Condensate Drain.
Field pitch a min. of
1/8" (3.2mm) per ft. (305mm).
Do not install an external trap.
F - Hot Water Reheat Return Line.
1/4" OD CU Humidifier Supply Line
(Steam Gen./Infrared)
1/2" NPT Male Steam
Humidifier Supply Line.
B - Condenser Water Supply Line
1/2" NPT Male Steam
Humidifier Return Line.
Table 36
DPN000554_Rev0
Downflow water cooled (DH) piping connection sizes, inches
Water Cooled Models
60 Hz (50 Hz)
A
(OD Cu)
B
(OD Cu)
C
(NPT Male)
D
(OD Cu)
E
(NPT Male)
F
(OD Cu)
1-5/8
1-5/8
1/2
5/8
1/2
5/8
3/4
7/8
3/4
7/8
NA
NA
NA
NA
DH086W (DH086W)
DH127W (DH128W)
DH138W (DH143W)
DH219W (DH219W)
DH267W (DH267W)
DH315W (DH315W)
2-1/8
2-1/8
DH412W (DH412W)
50
Water Cooled Models
Figure 34 Upflow water cooled (VH) piping connections
(22.2mm)
Optional Steam Humidifier
Install field
Unit
piping
Left End Panel
through
factorysupplied cover plate
(not shown for clarity).
Seal around all piping
penetrations.
Optional Steam Reheat
See Figure 37 for piping
connecton sizes.
Optional Hot Water Reheat (2-Way Valve)
Optional Hot Water Reheat (3-Way Valve)
DPN000555 Rev0
51
Water Cooled Models
Table 37
Factory-provided piping connection sizes, inches, upflow water cooled (VH)
Water Cooled Models
50 Hz
60 Hz
A
OD Cu
B
OD Cu
C
NPT FEMALE
D
OD Cu
E
NPT FEMALE
F
OD Cu
VH-086W
VH-086W
1-5/8
1-5/8
1/2
5/8
1/2
5/8
VH-128W
VH-127W
1-5/8
1-5/8
1/2
5/8
1/2
5/8
VH-143W
VH-138W
1-5/8
1-5/8
1/2
5/8
1/2
5/8
VH-219W
VH-219W
2-1/8
2-1/8
3/4
7/8
3/4
7/8
VH-267W
VH-267W
2-1/8
2-1/8
3/4
7/8
3/4
7/8
VH-315W
VH-315W
2-1/8
2-1/8
NA
NA
NA
NA
VH-412W
VH-412W
2-1/8
2-1/8
NA
NA
NA
NA
52
Water Cooled Models
NOTES
53
Water Cooled Models
54
Ensuring The High Availability
0f Mission-Critical Data And Applications.
Emerson Network Power, the global leader in enabling business-critical
continuity, ensures network resiliency and adaptability through
a family of technologies—including Liebert power and cooling
technologies—that protect and support business-critical systems.
Liebert solutions employ an adaptive architecture that responds
to changes in criticality, density and capacity. Enterprises benefit
from greater IT system availability, operational flexibility and
reduced capital equipment and operating costs.
Technical Support / Service
Web Site
www.liebert.com
Monitoring
800-222-5877
monitoring@emersonnetworkpower.com
Outside the US: 614-841-6755
Single-Phase UPS
800-222-5877
upstech@emersonnetworkpower.com
Outside the US: 614-841-6755
Three-Phase UPS
800-543-2378
powertech@emersonnetworkpower.com
Environmental Systems
800-543-2778
Outside the United States
614-888-0246
Locations
United States
1050 Dearborn Drive
P.O. Box 29186
Columbus, OH 43229
Europe
Via Leonardo Da Vinci 8
Zona Industriale Tognana
35028 Piove Di Sacco (PD) Italy
+39 049 9719 111
Fax: +39 049 5841 257
Asia
7/F, Dah Sing Financial Centre
108 Gloucester Road, Wanchai
Hong Kong
852 2572220
Fax: 852 28029250
While every precaution has been taken to ensure the accuracy
and completeness of this literature, Liebert Corporation assumes no
responsibility and disclaims all liability for damages resulting from use of
this information or for any errors or omissions.
© 2006 Liebert Corporation
All rights reserved throughout the world. Specifications subject to change
without notice.
® Liebert and the Liebert logo are registered trademarks of Liebert
Corporation. All names referred to are trademarks
or registered trademarks of their respective owners.
SL-18200_REV1_08-06
Emerson Network Power.
The global leader in enabling Business-Critical Continuity™.
AC Power Systems
Embedded Computing
Embedded Power
Connectivity
DC Power Systems
Integrated Cabinet Solutions
EmersonNetworkPower.com
Outside Plant
Services
Power Switching & Control
Site Monitoring
Precision Cooling
Surge Protection
Business-Critical Continuity, Emerson Network Power and the Emerson Network Power logo are trademarks and service marks of Emerson Electric Co.
©2006 Emerson Electric Co.