WASHING MACHINE
FLS 571 C
FLS - 571C
3
4
5
6
7
8
9
2
10 11 12 13 14
1 13 12
3
2
11
1
10 9
4
8
7
6
5
INSTRUCTION BOOKLET
35.292.486/0
Important Safety Information
It is most important that this instruction book should be retained with the appliance for future reference.
Should the appliance be sold or transferred to another owner, or should you move house and leave the
appliance, always ensure that the book is supplied with the appliance in order that the new owner can get to
know the functioning of the appliance and the relevant warnings.
These warnings have been provided in the interest of safety. You MUST read them carefully before installing or
using the appliance.
CHECK THE APPLIANCE UPON RECEPTION AND SHOULD ANY DAMAGE BE OBSERVED CALL YOUR
RETAILER BEFORE YOU MAKE IT WORK.
Installation
■
■
■
■
■
■
■
■
Use
This appliance is heavy. Care should be taken when
moving it.
It is dangerous to alter the specifications or attempt to
modify this product in any way.
All packing and transit bolts must be removed before
use. Serious damage can occur to the product and to
property if this is not adhered to. See relevant section in
instructions.
Any plumbing work required to install this appliance
should be carried out by a qualified plumber or
competent person.
Any electrical work required to install this appliance
should be carried out by a qualified electrician or
competent person.
Care must be taken to ensure that the appliance does not
stand on the electrical supply cable.
If the machine is situated on a carpeted floor, please
adjust the feet in order to allow air to circulate freely.
The washing machine must be unplugged when
removing the interior transits bolts. Do not plug the
appliance before finishing the removal of the transit
bolts and the fixing of the caps in the holes where the
security bolts were
■
■
■
■
■
■
■
■
■
Child Safety
■
■
■
■
■
This appliance is designed to be operated by adults.
Children should not be allowed to tamper with the
controls or play with the product.
Pets and children have been known to climb into
washing machines. Please check your drum before use.
The glass door becomes very hot during the washing
cycle. Keep children away from the vicinity of the
appliance whilst it is in operation.
Keep all packaging well away for children.
Keep all detergents in a safe place out of children’s
reach.
■
■
■
■
2
Always unplug the appliance and turn off the water after use.
Do not overload the appliance. See relevant section in
instruction book.
Always look through the glass door to check if water has
drained before opening the door before draining the water. If
in doubt, refer to your instruction book
The user should always check that they have not left their
gas lighter (disposable or otherwise) in their clothing
Only wash fabrics which are designed to be machine
washed. If in doubt, consult the care label on the clothes.
Before washing, ensure that all pockets are empty and
buttons and zips are fastened. Avoid washing frayed or torn
articles and treat stains such as paint, ink, rust, and grass
before washing. Underwired bras must NOT be machine
washed.
Any objects such as coins, safety pins, nails, screws, stones
or any other hard, sharp material can cause extensive
damage and must not be placed into the machine.
Garments which have been in contact with volatile
petroleum products should not be machine washed. If
volatile cleaning fluids are used, care should be taken to
ensure that the fluid is removed from the garment before
placing in the machine.
Wash small items such as socks, laces, washable belts etc in
a washing bag or pillow case as it is possible for such items
to slip down between the tub and the inner drum.
Only use the advised quantities of fabric softener. Damage to
the fabric can ensue if you over-fill. Refer to the
manufacturer’s recommendations of quantities.
As some duvets and eiderdowns should be washed in large
commercial machines because of their bulk, please check
with the manufacturer of the item before washing in a
domestic machine.
Leave the porthole door slightly ajar between washes to
preserve the door seal.
Under no circumstances should you attempt to repair the
machine yourself. Repairs carried out by inexperienced
persons may cause injury or serious malfunctioning. Contact
your local Zanussi Service Centre. Always insist on genuine
Zanussi spare parts.
Table of Contents
For the User
For the Installer
Important Safety Information
Description of the Appliance
The Control Panel
Operating sequence
Before the first use
Load the laundry
Measure out the detergent
Measure out the additive
Select the required programme
Start the machine
At the end of the programme
Washing Programmes
Washing Hints
Wash Care Symbols
Maintenance and Cleaning
Descaling
After each wash
External cleaning
Cleaning the dispenser drawer
Cleaning the drawer recess
Cleaning the filter
The dangers of freezing
Something Not Working
Service and Spare Parts
Installation Instructions
Technical Specifications
2
4
Unpacking
Positioning
Water inlet
Water drainage
Levelling
Special conditions
Electrical connections
Permanent connection
5
6-7
6
6
6
6
7
7
7
8-9
10
11
12-13
12
12
12
12
12
13
13
14
14
Guide to use the Instruction Book
The following symbols will be found in the text to guide you throughout the instructions:
Safety instructions
i Hints and tips
How do we help to protect the environment?
We use recycled paper!
3
15
15
16
17
17
17-18
18
18
19
19
Description of the Appliance
4
1 2
Detergent dispenser drawer
Programme guide
“Mains-on” light
“Options” buttons
Program selector dial & ON/OFF switch
Door opening handle
Filter
Adjustable feet
5
3
FLS - 571C
2
3
4
5
6
7
8
9
2
10 11 12 13 14
1 13 12
3
1
11
10 9
4
8
7
6
5
1
2
3
4
5
6
7
8
6
7
8
Detergent dispenser drawer
Prewash
Wash
Fabric softener
AL035
4
The Control Panel
FLS - 571C
3
4
5
6
7
8
9
2
10 11 12 13 14
1 14 13
4
3
2
12
1
11 10
5
9
6
3
4
1 Programme Guide
7
2
8
1
5
4 Cold Wash button
Pressing this button when starting any program it will be
run through with cold water. All other features of the
program as intensity and duration remain unchanged.
Advisable for synthetic and delicate fabrics: curtains,
stores and other not too dirty fabrics
2 ON/OFF LAMP
It lights when the appliance is operating.
3 Half load button
5. PROGRAM SELECTOR
Available only for programmes 1 to 5
Pressing this button before starting the intense program
there will be one rinse less which leads to energy and
water saving
To select the required program turn the control
clockwise until the marker on the top coincides with the
number of the required program (reference mark on the
control panel).If at any chance you pass by the required
number NEVER TURN THE CONTROL
ANTICLOCKWISE just continue clockwise until the
required number is reached again.
5
Operating Sequence
i Before your first wash, we recommend that
you run a cotton cycle at 60°C, without any
laundry in the machine, to remove any
manufacturing residue from the drum and tub.
Pour 1/2 a measure of detergent into the
dispenser drawer and start the machine.
1. Load the laundry
Open the door.
Place the laundry in the drum, one item at a time,
shaking them out as much as possible.
Close the door.
Do not overload the washing machine, but always try
to use it utmost capacity in accordance with the type of
fabric. Reduce the quantity when washing very dirty or
fluffy laundry.
P0004
2. Measure out the detergent
Pull out the dispenser drawer until it stops.
Measure out the amount of detergent recommended by
the manufacturer in a graduated cup and pour it into the
main wash compartment .
If you wish to carry out a prewash(*), pour detergent
into the appropriate compartment marked
(*) Prewash is available in programme “1”.
AL025
3. Measure out the additive
If required, pour fabric softener into the compartment
marked
(the amount used must not exceed the
«MAX» mark in the drawer).
Close the drawer gently.
AL023
6
4. Select the required programme
Turn the programme selector dial CLOCKWISE to the
required programme.
2
P0215
5. Start the machine
Before starting up the machine check that:
■ the appliance is plugged in
■ the water supply tap is turned on
■ the door and the detergent dispenser drawer are
closed.
Pull the programme selector selector dial outwards, the
operating pilot light will illuminate and the machine will
start operating.
2
P0216
6. At the end of the programme
The machine stops automatically and the operating pilot
light goes out.
The door is controlled by a safety device which releases
3 minutes after the end of the programme.
Before opening the door ensure there is no water in
the drum.
Switch the machine off by depressing the programme
selector dial.
When the programme has finished, you are advised to
unplug the appliance and turn off the water tap.
Leave the door open to prevent the formation of mildew
and unpleasant smells.
7
Washing Programmes
Programmes for cotton and linen
Maximum load 5 kg
Program.
dial
position
Program
1
Whites with
prewash
90°
Heavy soiled
Prewash at 40 ˚C
Wash at 90˚C
4 rinses
Spin at 500 rpm
2
Whites
without
prewash
90°
Normal soiled
Wash at 90˚C
4 rinses
Spin at 500 rpm
3 (•)
Fast
Coloureds
60°
Normal soiled
Wash at 60˚C
4 rinses
Spin at 500 rpm
4
Non Fast
Coloureds
40°
Normal soiled
Wash at 40˚C
4 rinses
Spin at 500 rpm
5
Rinses
4 rinses
Spin at 500 rpm
6
Additives
softener
Load additive
1 rinses
Spin at 500 rpm
7
Spin
Draining of water
Spin at 500 rpm
Temperature ˚C
Degree of soil
Compartments
to use
Description
Possible
options
(•)This 60˚C programme is the reference programme for the Energy label
according to the article 2, paragraph 1 of the EEC Directive 92/75
8
Washing Programmes
Programmes for synthetics, delicates and wool
Maximum load 2 kg (wool maximum load 1 kg)
Program.
dial
position
Program
8
Mixed
Fabrics
60°
Heavy soiled
Prewash at 40 ˚C
Wash at 60˚C
3 rinses
Stop with water
9
Non Fast
Coloureds
60°
Normal soiled
Wash at 60˚C
3 rinses
Stop with water
10
Synthetics
Delicates
40°
Normal soiled
Wash at 40˚C
3 rinses
Stop with water
11
Wool Silk
40°
Normal soiled
Wash at 40˚C
3 rinses
Stop with water
12
Rinses
Delicates
3 rinses
Stop with water
13
Additives
Softener
Load additive
1 rinses
Stop with water
14
Drain
Draining of water
Temperature ˚C
Degree of soil
Compartments
to use
Description
Possible
options
The machine will stop after the last rinse with water in the drum. To prevent water spillage you must select either
Drain (14) or Spin (7) before attempting to open the door.
9
i Washing Hints
Do NOT overload the machine. Weigh the laundry the
first few times you use the appliance.
■
The average weights of the most common items are
listed below as a guide:
1000g = 1 kg
■
Sheet
700-1000 g
Pillow case
100-200 g
Tablecloth
400-500 g
Serviette
50-100 g
Tea towel
70-120 g
Linen hand towel
100-150 g
Toweling hand towel
150-250 g
Toweling bath towel
700-1000 g
Bath robe
■
■
1000-1500 g
Man’s shirt
200-300 g
Apron
150-200 g
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
Load the laundry loosely alternating large items with
small ones.
Sort the laundry according to the type of fabric,
colour-fastness and how dirty it is.
Avoid washing unhemmed or torn items as they may
unravel.
Before washing, empty all pockets of small objects
which may have been left inside (coins, keys, screws
etc). as these could damage the drain pump.
When washing curtains, remove the hooks.
Close poppers and zips and fasten loose buttons.
It is essential to wash new coloured items separately
when washing for the first time.
When washing fabrics requiring different wash
temperatures together, always select the lowest
temperature.
White items should not be washed with coloured
items.
Very small items (handkerchiefs, ribbons, socks etc)
should be washed in a washing bag or a pillow case.
Use a good quality detergent suitable for automatic
washing machines.
Use the correct quantities of detergent.
For wool, use gentle detergent only in small
quantities.
Bleach is very corrosive; it should be used with care
and kept out of reach of children.
10
Some stains such as fruit, wine, grass, rust etc. are
difficult to remove and should be treated before
washing with specific products, which can be found
in most household shops. In some cases it may help
to soak the stain before washing with a special presoak product or biological detergent.
Only wool marked «Pure New Wool - washable,
preshrunk» can be washed in the machine using the
wool programme; other types of wool should be
washed by hand or dry cleaned.
If you have used the machine to wash, rinse or spin
only non-colour fast garments, there may be dye left
in the sump. To ensure any subsequent wash is not
contaminated with the dye, select and carry out a
rinse and spin programme, without any garments, to
ensure that any dye is removed from the sump.
Once you have finished using the machine, you are
advised to unplug it and turn off the water tap.
To avoid an excessive and damaging amount of
lather when washing net curtains, it is advisable to
wash large curtains singularly and take extra care
when measuring the detergent.
Should an excess of lather accidentally occur, switch
off the machine, select the spin programme which is
preceded by a drain cycle, to remove the lather and
then start the wash again.
Wash Care Symbols
Wash care labels inside garments recommend how to launder your clothes with the best results. The care labelling
code is in line with care labelling used in the rest of Europe. The symbols used make it easy to select the correct
programme on your washing machine.
WASHING SYMBOL
WASH ACTION
95
Normal (Maximum)
White Cotton or Linen
without Special Finishes
60
Normal (Maximum)
Cotton, Linen or Viscose
without Special Finishes
Colour fast at 60°C.
50
Reduced (Medium)
40
Normal (Maximum)
40
Reduced (Medium)
40
Much Reduced (Minimum)
Hand wash only
FABRIC
Nylon, Polyester/Cotton, Viscose
with
Special
Finishes,
Cotton/Acrylic Mix.
Cotton, Linen or Viscose
Colour fast at 40°C but not 60°C.
Acrylics, Acetate, Triacetate, Wool
mixes, Polyester/wool blends.
Wool, wool mixtures, Silks
Do not machine wash
BLEACHING
Chlorine bleach may be used
IRONING
Hot iron
Cotton, Linen, Viscose
Warm iron
Polyester mixtures, Wool
Cool iron
Acrylic, Nylon, Polyester
DRY CLEANING
P
May be dry cleaned. Other letters and/or a bar beneath the circle will
indicate the required process to the dry cleaner.
TUMBLE DRYING
May be tumble dried
with high heat setting
with low heat setting
X
A cross through any symbol means «DO NOT»
Important Notes
For best results, always use the dispenser drawer for dispensing detergents and liquid additives.Once the dispenser has
been filled, close it by pushing it in gently. This is particularly important if you are using fabric conditioner to avoid
the conditioner entering the machine prematurely.
When using liquid detergent and a prewash programme, place the detergent into the correct compartment in the
dispenser drawer, after the prewash has finished.
11
Maintenance and Cleaning
Before any maintenance or cleaning is carried
out you must DISCONNECT the appliance
from the electricity supply
Descaling
The water we normally use contains lime. It is a good
idea to periodically use a water softening powder in the
machine. Do this separately from any laundry washing,
and according to the softening powder manufacturer's
instructions. This will help to prevent the formation of
lime deposits.
After each wash
Leave the door open for a while. This helps to prevent
mould and stagnant smells forming inside the appliance.
Keeping the door open after a wash will also help to
preserve the door seal.
External cleaning
Clean the exterior cabinet of the appliance with soap
and water only, and then dry thoroughly.
Cleaning the dispenser drawer
From time to time the washing powder and additive
dispenser drawer should be cleaned.
Remove the drawer by pressing the catch downwards
and by pulling it out. Flush it out under a tap, to remove
AL021
any traces of accumulated powder.
Keep clean the control panel to avoid liquids to
spread in the inside part of the panel
Cleaning the drawer recess
Having removed the drawer, use a small brush to clean
the recess, ensuring that all washing powder residue is
removed from the upper and lower part of the recess.
Replace the drawer and run the rinse programme for a
P0185
few minutes without any clothes in the drum.
12
AL033
Cleaning the filter
The water drain filter
A clean filter is important for the correct functioning of
the machine, and should therefore be cleaned after every
washing programme.
Open the filter door and place a container underneath to
catch any spillage. If the filter is blocked and the
machine is unable to drain you will need to drain the
water manually from the machine at this stage. To do
this, unhook the drain hose from the standpipe or sink
and hold the end of the hose over a bowl on the floor.
The water should drain by gravity into the bowl. When
the bowl is full, hook the hose back up and empty the
bowl. Repeat the procedure until water stops flowing
out.
Unscrew and remove the filter.
Clean carefully under a fast running tap.
Replace the filter turning now clockwise and tighten it.
P0040
Warning
When the appliance is in use and depending on the
programme selected there can be hot water in the filter.
Never remove the filter during a wash cycle, always
wait until the appliance has finished the cycle, and is
empty. When replacing the filter, ensure it is securely
retightened so as to stop leaks and young children being
able to remove it.
The water inlet filter
If your water is very hard or contains traces of lime
deposit, the water inlet filter may become clogged.
It is therefore a good idea to clean it from time to time.
Turn off the water tap. Unscrew the water inlet hose.
Remove and clean the filter using a hard bristle brush.
Replace the filter and tighten up the inlet hose.
P0090
The dangers of freezing
If the machine is exposed to temperatures below 0°C,
certain precautions should be taken.
■ Turn off the water tap.
■ Unscrew the inlet hose.
■ Unhook the drain hose from the rear support and
position the end of this hose and that of the inlet
hose in a bowl. Run the draining programme.
■ Disconnect the appliance.
■ Screw the inlet hose and reposition the drain hose.
■ When you intend to start the machine up again,
make sure that the room temperature is above 0°C.
13
P0021
Something Not Working
Certain problems are due to lack of simple maintenance or oversights, which can be solved easily without calling out
an engineer. Before contacting your Local service Force Centre, please carry out the checks listed below.
Symptom
Possible causes
The machine does not start
■
■
■
■
■
■
The machine does not fill
■
■
■
■
The machine fills then empties
immediately
■
■
■
The machine does not empty and/or
does not spin
■
■
■
■
There is water on the floor
■
■
■
■
■
The machine vibrates or is noisy
■
■
■
■
■
■
The door has not been closed.
The plug is not properly inserted in the power socket.
There is no current at the socket
The main fuse has blown.
The selector dial is not correctly positioned and pulled out
No water is entering the machine (see: the machine does not fill)
Ensure the water tap is open and the water supply has not been disconnected
The filter in the inlet hose is blocked.
The inlet hose may be squashed or kinked.
The water pressure is too low
The end of the drain hose is too low.
The end of the drain hose is submerged in water.
There is no vent in the end of the drain hose.
The drain hose may be squashed or kinked
The drain filter may be blocked
The drain hose extension is not correct. Follow the instructions for
connecting to the waste.
The drainage system pipes are blocked.
Too much detergent or unsuitable detergent has been used (creates too
much foam).
Check whether there are any leaks from the inlet hose fittings. It is not
always easy to see this as the water runs down the hose; check to see if
it is damp.
The drain hose may be damaged or not securely positioned.
The detergent dispenser drawer or recess is clogged.
The drainage system pipes are blocked.
The internal packing has not been removed.
The machine is in contact with the wall or furniture.
The machine is not level.
The washing load is badly distributed in the drum.
Maybe there is very little laundry in the drum.
The machine is overloaded
If after all these checks, the problem persists, contact
your local Service Force Centre, quoting the model and
serial number. This information can be found on the
rating plate (see picture).
Please note that it will be necessary to provide proof of
purchase for any in-guarantee service calls. In-guarantee
customers should ensure that the above checks have
been made as the engineer will make a charge if the
fault is not a mechanical or electrical breakdown.
Mod.
..........
Ser.
Mod. ..........
Prod. No. ...........
P0042
14
Ser. No. .........
Installation Instructions
It is dangerous to alter the specifications or
attempt to modify this product in any way.
Care must be taken to ensure that the appliance
does not stand on the electrical supply cable.
Any electrical work required to install this
appliance should be carried out by a qualified
electrician or competent person.
Any plumbing work required to install this
appliance should be carried out by a qualified
plumber or competent person.
Technical Specifications
DIMENSIONS
Height
Width
Depth
POWER SUPPLY VOLTAGE
MAX. POWER ABSORBED
85 cm
60 cm
55 cm
220-230 V/50 Hz
2200 W (10A)
WATER PRESSURE
Minimum
Maximum
MAXIMUM RECOMMENDED LOAD
Cotton, linen
Synthetics
Delicate fabrics
Wool
SPIN SPEED
Maximum
This appliance complies with the following E.E.C. Directives:
- 73/23 EEC of 19.2.73 (Low Voltage Directive) and subsequent modifications;
- 89/336 EEC of 3.5.89 (Electromagnetic Compatibility Directive) and subsequent modifications.
15
5 N/cm2
80 N/cm2
5 kg
2 kg
2 kg
1 kg
500 rpm
Unpacking
Before starting the machine up, the transport security
bolts must be removed as follows:
You are advised to keep all the packaging for re-use in
case the appliance has to be transported again.
■
Unscrew and remove the three rear transit bolts
(using a spanner).
P0287
■
Lay the machine gently on its back, making sure
that the hoses are not squashed.
We suggest a polystyrene angle bracket from the
packing is placed on the floor before tilting it back
to avoid the hoses being squashed.
P0018
■
Carefully remove the polyethylene bags located at
the base of the machine by pulling them toward the
centre of the machine.
1
AL009
■
Place the machine in an upright position and
remove the three plastic bolts.
P0001
■
Plug the 3 holes with the plastic plugs which you
can find in the envelope containing the instruction
booklet.
P0002
16
2
Positioning
Your new Zanussi washing machine has been designed
to be permanently plumbed in to you home’s water
supply and drainage system. However, if this is not
possible, it may be connected to suitable existing taps,
with the drain hose discharging into the sink.
Water inlet
There should be a COLD WATER tap near the washing
machine with a screwing on connection pipe of 3/4 gas
for the water supply, a sink, a wash basin or a drainage
system in the wall.
Previously check if:
■ it is not a hot water tap.
■ the running water is clean. If not, run off a
reasonable amount of water to flush out any debris
that may have collected in the pipes.
Have the permanent drainage system in the wall
checked by a plumber.
Place the enclosed rubber joint, delivered in a plastic
bag together with the appliance (A), at the very end of
the inlet hose and carefully screw the pipe to the tap
taking care not to damage the screwdrive and fix the nut
well on to the end in order to avoid leaking.
A
AL013
If necessary turn the hose adequately by unscrewing the
nut at the rear of the appliance.
Now tighten the nut anew to avoid leaks. (Open the tap
and assure that it does not leak and close it again.)
P0021
Water drainage
If you intend the drain hose from the machine to empty
into a sink, make sure that the sink is empty and that the
plug hole is not blocked.
Place the drain hose in the sink with the aid of the bent
piece delivered separately.
The bent piece has to be entered into the tube´s mouth
in order to assure the support.. Aforesaid piece allows
the hose to be fixed to the wall by means of an opening
on the upper part and that way the hose does not move
and its falling is avoided
P0022
17
If the machine is permanently plumbed in, hook the end
of the hose into a standpipe installed for the purpose.
The standpipe must have an internal diameter of at least
40mm in order that there is an air gap between the drain
hose and the standpipe. Make sure, that it is designed in
such a way, that the end of the drain hose cannot be
covered with water.
Whether discharging into a sink or a standpipe check
that the end of the drain hose is neither too high nor too
low. The top of the curve in the hose’s end should be no
more than 90 cm, and no less than 60 cm above floor
level.
Should a prolongation of the drain hose be unavoidable
this must never surpass 1.5 m and must be of the same
diameter as the original hose
P1039
Important
Before connecting up the machine to new pipework or
to pipework that has not been used for some time, run
off a reasonable amount of water to flush out any debris
that may have collected in the pipes.
Levelling
Level the washing machine by loosening or tightening
the feet. Once in the right position fix the feet by
pushing the nuts against the base of the case
Accurate levelling prevents vibration, noise and
displacement of the machine during operation. After
levelling the machine, secure the feet by tightening the
ring nuts with the aid of a screwdriver.
Some vibration is inevitable, especially if mounted on a
wooden floor.
Sprung wooden floors are particularly susceptible to
vibration. For advice, consult a builder. If possible,
always place the machine on a solid floor.
P0254
Special conditions
If the floor is carpeted with a deep-pile carpet or
covered with crumbly or soft material, insert a rigid
support base under the feet to prevent noise, vibration or
displacement. The base should protrude a few
centimetres beyond the edges of the machine.
Warning
The machine should NOT be placed on deep pile
carpeting.
Note
Please ensure that when the appliance is installed it is
easily accessible for the engineer in the event of a
breakdown.
18
P0509
Min.60 cm.
(23.6")
Max. 90 cm.(35.4")
3 pin
Electrical connections
Any electrical work required to install this appliance
should be carried out by a qualified electrician.or
competent person
WARNING: THIS APPLIANCE MUST BE
EARTHED.
The manufacturer declines any liability should
this safety measure not be observed.
Before switching on, make sure the electricity supply
voltage is the same as that indicated on the appliance
rating plate. (the plate is sticked to the rear of the
appliance).
The appliance is supplied with a 10 amp plug fitted. In
the event of having to change the fuse in the plug
supplied, use a 10 Amp fuse.
Should the plug need to be replaced for any reason,
proceed as described below.
The wires in the mains lead are coloured in accordance
with the following code:
Green and Yellow
- Earth
Blue
- Neutral
Brown
- Live
Connect the green and yellow (earth) wire to the
terminal in the plug which is marked with the letter «E»
or the earth symbol
or coloured green and yellow.
Connect the blue (neutral) wire to the terminal in the
plug which is marked with the letter «N» or coloured
black.
Connect the brown (live) wire to the terminal in the plug
which is marked with the letter «L» or coloured red.
The plug must not be used if the fuse cover/carrier is
lost. The cover/carrier is indicated by the coloured insert
at the base of the plug.
A replacement cover/carrier must be obtained from your
local Zanussi Service Centre, whose address is listed in
the Customer Care Booklet which accompanies your
instruction manual
GREEN & YELLOW
13 A
E
N
L
BROWN
BLUE
P1041
CORD CLAMP
Permanent connection
In the case of permanent connection it is necessary that
you install a double pole switch between the appliance
and the electricity supply (mains), with a minimum gap
of 3 mm between the switch contacts and of a type
suitable for the required load in compliance with the
current electrical regulations.
The switch must not break the yellow and green earth
cable at any point.
WARNING: a cut off plug inserted into a 10
amp socket is a serious safety (shock) hazard.
Ensure that the cut off plug is disposed of
safely.
19
EPESL