Emerson CR202EM9 Service manual

TM
EMERSON AND THE G-CLEF LOGO ARE REGISTERED TRADEMARKS
OF EMERSON RADIO CORP., PARSIPPANY, NEW JERSEY, U.S.A.
SERVICE MANUAL
20″ DIGITAL / ANALOG
PURE FLAT TELEVISION
CR202EM8
IMPORTANT SAFETY NOTICE
Proper service and repair is important to the safe, reliable operation of all
Funai Equipment. The service procedures recommended by Funai and
described in this service manual are effective methods of performing
service operations. Some of these service special tools should be used
when and as recommended.
It is important to note that this service manual contains various CAUTIONS
and NOTICES which should be carefully read in order to minimize the risk
of personal injury to service personnel. The possibility exists that improper
service methods may damage the equipment. It also is important to
understand that these CAUTIONS and NOTICES ARE NOT EXHAUSTIVE.
Funai could not possibly know, evaluate and advice the service trade of all
conceivable ways in which service might be done or of the possible
hazardous consequences of each way. Consequently, Funai has not
undertaken any such broad evaluation. Accordingly, a servicer who uses a
service procedure or tool which is not recommended by Funai must first
use all precautions thoroughly so that neither his safety nor the safe
operation of the equipment will be jeopardized by the service method
selected.
TABLE OF CONTENTS
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
Important Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
Standard Notes for Servicing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
Cabinet Disassembly Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
Electrical Adjustment Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
How to initialize the Television. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1
Block Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1
Schematic Diagrams / CBA’s and Test Points. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1
Waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-1
Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-1
IC Pin Function Descriptions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-1
Exploded Views. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-1
Mechanical Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-1
Electrical Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-1
SPECIFICATIONS
< TUNER >
ANT. Input ---------------------- 75 ohm Unbal., F type
Reference Level--------------- 20 Vp-p (CRT Green Cathode)
Test Input Signal -------------- 400 Hz 30% modulation
Description
Condition
Unit
Nominal
Limit
1. Intermediate Freq.
Picture
Sound
MHz
MHz
45.75
41.25
-----
2. Peak Picture Sens
VHF
CATV
UHF
dBµV
dBµV
dBµV
15
15
15
30
30
40
---
MHz
±2.0
±0.7
Condition
Unit
Nominal
Limit
1. Deflection Freq.
Horizontal
Vertical
kHz
Hz
15.734
60
-----
2. Linearity
Horizontal
Vertical
%
%
-----
±18
±10
3. Over Scan
---
%
10
---
4. High Voltage
---
kV
25
---
Condition
Unit
Nominal
Limit
Center
Side
Corner
mm
mm
mm
-------
0.4
1.5
2.5
APL 100%
Ft-L
25
15
---
°K
9200
---
Horizontal
Vertical
Line
Line
250
300
-----
3. AFT Pull In Range (10 mV input)
< DEFLECTION >
Description
< VIDEO & CHROMA >
Description
1. Misconvergence
2. Brightness
3. Color Temperature
4. Resolution
< AUDIO >
All items are measured across 8 Ω load at speaker output terminal.
Description
1. Audio Output Power
2. Audio Distortion (w/LPF)
3. Audio Freq. Response
Condition
Unit
Nominal
Limit
10% THD
W
1
0.8
500 mW
%
2
7
-3 dB
Hz
70 ~ 11 k
---
1-1
P7150SP
< ATSC >
Description
1. RECEIVED FREQ. RANGE
(-28dBm)
Condition
+
–
Unit
Nominal
Limit
kHz
150
>100
-82/6
-76/0
-82/6
-76/0
-80/6
-74/4
dB
23
<26
dB
0
>-6
dB
0
<6
dB
60
>50
%
0.5
<3
VHF LOW BAND. CH.4
2. ATSC DYNAMIC RANGE
(min./max.)
VHF HI BAND. CH.10
dBm
UHF BAND. CH.41
VHF LOW BAND. CH.4
3. ATSC SUSCEPTIBILITY TO
RANDOM NOISE
VHF HI BAND. CH.10
UHF BAND. CH.41
VHF LOW BAND. CH.4
4. NTSC CO-CHANNEL
INTERFERENCE
VHF HI BAND. CH.10
UHF BAND. CH.41
A
B
C
5. MULTIPATH
D
E
F
FF
G
6. Audio S/N (0dBfs)
7. Audio DIST. (0dBfs)
Lch
Rch
Lch
Rch
Note: Nominal specifications represent the design specifications. All units should be able to approximate these.
Some will exceed and some may drop slightly below these specifications. Limit specifications represent
the absolute worst condition that still might be considered acceptable. In no case should a unit fail to meet
limit specifications.
1-2
P7150SP
IMPORTANT SAFETY PRECAUTIONS
Prior to shipment from the factory, our products are strictly inspected for recognized product safety and electrical
codes of the countries in which they are to be sold. However, in order to maintain such compliance, it is equally
important to implement the following precautions when a set is being serviced.
Safety Precautions for TV Circuit
AC line cord directly into a 120 V AC outlet. (Do
not use an isolation transformer during this
test.) Use a leakage current tester or a
metering system that complies with American
National Standards Institute (ANSI) C101.1
Leakage Current for Appliances and
Underwriters Laboratories (UL) 1410, (50.7).
With the instrument AC switch first in the on
position and then in the off position, measure
from a known earth ground (metal water pipe,
conduit, etc.) to all exposed metal parts of the
instrument (antennas, handle brackets, metal
cabinet, screw heads, metallic overlays, control
shafts, etc.), especially any exposed metal
parts that offer an electrical return path to the
chassis. Any current measured must not
exceed 0.5 milli-ampere. Reverse the
instrument power cord plug in the outlet and
repeat the test.
1. Before returning an instrument to the
customer, always make a safety check of the
entire instrument, including, but not limited to, the
following items:
a. Be sure that no built-in protective devices are
defective and have been defeated during
servicing. (1) Protective shields are provided
on this chassis to protect both the technician
and the customer. Correctly replace all missing
protective shields, including any removed for
servicing convenience. (2) When reinstalling
the chassis and/or other assembly in the
cabinet, be sure to put back in place all
protective devices, including but not limited to,
nonmetallic control knobs, insulating
fishpapers, adjustment and compartment
covers/shields, and isolation resistor/capacitor
networks. Do not operate this instrument or
permit it to be operated without all
protective devices correctly installed and
functioning. Servicers who defeat safety
features or fail to perform safety checks
may be liable for any resulting damage.
READING SHOULD
NOT BE ABOVE 0.5 mA
DEVICE
BEING
TESTED
b. Be sure that there are no cabinet openings
through which an adult or child might be able to
insert their fingers and contact a hazardous
voltage. Such openings include, but are not
limited to, (1) spacing between the picture tube
and the cabinet mask, (2) excessively wide
cabinet ventilation slots, and (3) an improperly
fitted and/or incorrectly secured cabinet back
cover.
LEAKAGE
CURRENT
TESTER
_
+
TEST ALL EXPOSED
METAL SURFACES
ALSO TEST WITH
PLUG REVERSED
USING AC
ADAPTER PLUG
AS REQUIRED
c. Antenna Cold Check - With the instrument AC
plug removed from any AC source, connect an
electrical jumper across the two AC plug
prongs. Place the instrument AC switch in the
on position. Connect one lead of an ohmmeter
to the AC plug prongs tied together and touch
the other ohmmeter lead in turn to each tuner
antenna input exposed terminal screw and, if
applicable, to the coaxial connector. If the
measured resistance is less than 1.0 megohm
or greater than 5.2 megohm, an abnormality
exists that must be corrected before the
instrument is returned to the customer. Repeat
this test with the instrument AC switch in the off
position.
EARTH
GROUND
ANY MEASUREMENTS NOT WITHIN THE
LIMITS SPECIFIED HEREIN INDICATE A
POTENTIAL SHOCK HAZARD THAT MUST
BE ELIMINATED BEFORE RETURNING THE
INSTRUMENT TO THE CUSTOMER OR
BEFORE CONNECTING THE ANTENNA OR
ACCESSORIES.
e. X-Radiation and High Voltage Limits Because the picture tube is the primary
potential source of X-radiation in solid-state TV
receivers, it is specially constructed to prohibit
X-radiation emissions. For continued Xradiation protection, the replacement picture
tube must be the same type as the original.
d. Leakage Current Hot Check - With the
instrument completely reassembled, plug the
2-1
TVN_ISP
an isolation transformer only if the AC power
plug is inserted so that the chassis is
connected to the ground side of the AC power
source. To confirm that the AC power plug is
inserted correctly, with an AC voltmeter,
measure between the chassis and a known
earth ground. If a voltage reading in excess of
1.0V is obtained, remove and reinsert the AC
power plug in the opposite polarity and again
measure the voltage potential between the
chassis and a known earth ground.
Also, because the picture tube shields and
mounting hardware perform an X-radiation
protection function, they must be correctly in
place. High voltage must be measured each
time servicing is performed that involves B+,
horizontal deflection or high voltage. Correct
operation of the X-radiation protection circuits
also must be reconfirmed each time they are
serviced. (X-radiation protection circuits also
may be called “horizontal disable” or “hold
down.”) Read and apply the high voltage limits
and, if the chassis is so equipped, the Xradiation protection circuit specifications given
on instrument labels and in the Product Safety
& X-Radiation Warning note on the service
data chassis schematic. High voltage is
maintained within specified limits by close
tolerance safety-related components/
adjustments in the high-voltage circuit. If high
voltage exceeds specified limits, check each
component specified on the chassis schematic
and take corrective action.
b. Some TV receiver chassis normally have 85V
AC(RMS) between chassis and earth ground
regardless of the AC plug polarity. This chassis
can be safety-serviced only with an isolation
transformer inserted in the power line between
the receiver and the AC power source, for both
personnel and test equipment protection.
c. Some TV receiver chassis have a secondary
ground system in addition to the main chassis
ground. This secondary ground system is not
isolated from the AC power line. The two
ground systems are electrically separated by
insulation material that must not be defeated or
altered.
2. Read and comply with all caution and safetyrelated notes on or inside the receiver cabinet, on
the receiver chassis, or on the picture tube.
3. Design Alteration Warning - Do not alter or add
to the mechanical or electrical design of this TV
receiver. Design alterations and additions,
including, but not limited to circuit modifications
and the addition of items such as auxiliary audio
and/or video output connections, might alter the
safety characteristics of this receiver and create a
hazard to the user. Any design alterations or
additions will void the manufacturer's warranty and
may make you, the servicer, responsible for
personal injury or property damage resulting
therefrom.
6. Observe original lead dress. Take extra care to
assure correct lead dress in the following areas: a.
near sharp edges, b. near thermally hot parts-be
sure that leads and components do not touch
thermally hot parts, c. the AC supply, d. high
voltage, and, e. antenna wiring. Always inspect in
all areas for pinched, out of place, or frayed wiring.
Check AC power cord for damage.
7. Components, parts, and/or wiring that appear to
have overheated or are otherwise damaged
should be replaced with components, parts, or
wiring that meet original specifications.
Additionally, determine the cause of overheating
and/or damage and, if necessary, take corrective
action to remove any potential safety hazard.
4. Picture Tube Implosion Protection Warning The picture tube in this receiver employs integral
implosion protection. For continued implosion
protection, replace the picture tube only with one
of the same type number. Do not remove, install,
or otherwise handle the picture tube in any
manner without first putting on shatterproof
goggles equipped with side shields. People not so
equipped must be kept safely away while picture
tubes are handled. Keep the picture tube away
from your body. Do not handle the picture tube by
its neck. Some “in-line” picture tubes are equipped
with a permanently attached deflection yoke;
because of potential hazard, do not try to remove
such “permanently attached” yokes from the
picture tube.
8. Product Safety Notice - Some electrical and
mechanical parts have special safety-related
characteristics which are often not evident from
visual inspection, nor can the protection they give
necessarily be obtained by replacing them with
components rated for higher voltage, wattage, etc.
Parts that have special safety characteristics are
identified by a # on schematics and in parts lists.
Use of a substitute replacement that does not
have the same safety characteristics as the
recommended replacement part might create
shock, fire, and/or other hazards. The product's
safety is under review continuously and new
instructions are issued whenever appropriate.
Prior to shipment from the factory, our products
are strictly inspected to confirm they comply with
the recognized product safety and electrical codes
5. Hot Chassis Warning a. Some TV receiver chassis are electrically
connected directly to one conductor of the AC
power cord and maybe safety-serviced without
2-2
TVN_ISP
3) Align the lengths of the wires to be connected.
Insert the wires fully into the connector.
of the countries in which they are to be sold.
However, in order to maintain such compliance, it
is equally important to implement the following
precautions when a set is being serviced.
4) Use the crimping tool to crimp the metal sleeve
at the center position. Be sure to crimp fully to
the complete closure of the tool.
Precautions during Servicing
L. When connecting or disconnecting the internal
connectors, first, disconnect the AC plug from the
AC supply outlet.
A. Parts identified by the # symbol are critical for
safety.
Replace only with part number specified.
B. In addition to safety, other parts and assemblies
are specified for conformance with regulations
applying to spurious radiation. These must also be
replaced only with specified replacements.
Examples: RF converters, RF cables, noise
blocking capacitors, and noise blocking filters, etc.
C. Use specified internal wiring. Note especially:
1) Wires covered with PVC tubing
2) Double insulated wires
3) High voltage leads
D. Use specified insulating materials for hazardous
live parts. Note especially:
1) Insulation Tape
2) PVC tubing
3) Spacers
4) Insulators for transistors.
E. When replacing AC primary side components
(transformers, power cord, etc.), wrap ends of
wires securely about the terminals before
soldering.
F. Observe that the wires do not contact heat
producing parts (heat sinks, oxide metal film
resistors, fusible resistors, etc.)
G. Check that replaced wires do not contact sharp
edged or pointed parts.
H. When a power cord has been replaced, check that
5~6 kg of force in any direction will not loosen it.
I.
Also check areas surrounding repaired locations.
J. Use care that foreign objects (screws, solder
droplets, etc.) do not remain inside the set.
K. Crimp type wire connector
The power transformer uses crimp type
connectors which connect the power cord and the
primary side of the transformer. When replacing
the transformer, follow these steps carefully and
precisely to prevent shock hazards.
Replacement procedure
1) Remove the old connector by cutting the wires
at a point close to the connector.
Important: Do not re-use a connector (discard
it).
2) Strip about 15 mm of the insulation from the
ends of the wires. If the wires are stranded,
twist the strands to avoid frayed conductors.
2-3
TVN_ISP
Safety Check after Servicing
Examine the area surrounding the repaired location for damage or deterioration. Observe that screws, parts and
wires have been returned to original positions. Afterwards, perform the following tests and confirm the specified
values in order to verify compliance with safety standards.
1. Clearance Distance
When replacing primary circuit components, confirm
specified clearance distance (d) and (d') between
soldered terminals, and between terminals and
surrounding metallic parts. (See Fig. 1)
Chassis or Secondary Conductor
Primary Circuit
Table 1: Ratings for selected area
AC Line Voltage
Region
Clearance
Distance (d), (d’)
110 to 130 V
U.S.A. or
Canada
≥ 3.2 mm
(0.126 inches)
d'
d
Note: This table is unofficial and for reference only. Be
sure to confirm the precise values.
Fig. 1
2. Leakage Current Test
Confirm the specified (or lower) leakage current
between B (earth ground, power cord plug prongs) and
externally exposed accessible parts (RF terminals,
antenna terminals, video and audio input and output
terminals, microphone jacks, earphone jacks, etc.) is
lower than or equal to the specified value in the table
below.
Exposed Accessible Part
Z
AC Voltmeter
(High Impedance)
Measuring Method: (Power ON)
Insert load Z between B (earth ground, power cord plug
prongs) and exposed accessible parts. Use an AC
voltmeter to measure across both terminals of load Z.
See Fig. 2 and following table.
B
Earth Ground
Power Cord Plug Prongs
Fig. 2
Table 2: Leakage current ratings for selected areas
AC Line Voltage
Region
Load Z
Leakage Current (i)
Earth Ground (B) to:
110 to 130 V
U.S.A. or
Canada
0.15 µF CAP. & 1.5 kΩ
RES. Connected in parallel
i ≤ 0.5 mA rms
Exposed accessible
parts
Note: This table is unofficial and for reference only. Be sure to confirm the precise values.
2-4
TVN_ISP
STANDARD NOTES FOR SERVICING
Circuit Board Indications
How to Remove / Install Flat Pack-IC
1. The output pin of the 3 pin Regulator ICs is
indicated as shown.
1. Removal
With Hot-Air Flat Pack-IC Desoldering Machine:
Top View
Out
1. Prepare the hot-air flat pack-IC desoldering
machine, then apply hot air to the Flat Pack-IC
(about 5 to 6 seconds). (Fig. S-1-1)
Bottom View
In
Input
2. For other ICs, pin 1 and every fifth pin are
indicated as shown.
5
Pin 1
10
3. The 1st pin of every male connector is indicated as
shown.
Fig. S-1-1
2. Remove the flat pack-IC with tweezers while
applying the hot air.
Pin 1
3. Bottom of the flat pack-IC is fixed with glue to the
CBA; when removing entire flat pack-IC, first apply
soldering iron to center of the flat pack-IC and heat
up. Then remove (glue will be melted). (Fig. S-1-6)
Pb (Lead) Free Solder
4. Release the flat pack-IC from the CBA using
tweezers. (Fig. S-1-6)
Pb free mark will be found on PCBs which use Pb
free solder. (Refer to figure.) For PCBs with Pb free
mark, be sure to use Pb free solder. For PCBs
without Pb free mark, use standard solder.
CAUTION:
1. The Flat Pack-IC shape may differ by models. Use
an appropriate hot-air flat pack-IC desoldering
machine, whose shape matches that of the Flat
Pack-IC.
2. Do not supply hot air to the chip parts around the
flat pack-IC for over 6 seconds because damage
to the chip parts may occur. Put masking tape
around the flat pack-IC to protect other parts from
damage. (Fig. S-1-2)
Pb free mark
3-1
TVN_SN
With Soldering Iron:
3. The flat pack-IC on the CBA is affixed with glue, so
be careful not to break or damage the foil of each
pin or the solder lands under the IC when
removing it.
CBA
1. Using desoldering braid, remove the solder from
all pins of the flat pack-IC. When you use solder
flux which is applied to all pins of the flat pack-IC,
you can remove it easily. (Fig. S-1-3)
Hot-air
Flat Pack-IC
Desoldering
Machine
Flat Pack-IC
Desoldering Braid
Soldering Iron
Masking
Tape
Tweezers
Flat Pack-IC
Fig. S-1-3
2. Lift each lead of the flat pack-IC upward one by
one, using a sharp pin or wire to which solder will
not adhere (iron wire). When heating the pins, use
a fine tip soldering iron or a hot air desoldering
machine. (Fig. S-1-4)
Fig. S-1-2
Sharp
Pin
Fine Tip
Soldering Iron
Fig. S-1-4
3. Bottom of the flat pack-IC is fixed with glue to the
CBA; when removing entire flat pack-IC, first apply
soldering iron to center of the flat pack-IC and heat
up. Then remove (glue will be melted). (Fig. S-1-6)
4. Release the flat pack-IC from the CBA using
tweezers. (Fig. S-1-6)
3-2
TVN_SN
With Iron Wire:
2. Installation
1. Using desoldering braid, remove the solder from
all pins of the flat pack-IC. When you use solder
flux which is applied to all pins of the flat pack-IC,
you can remove it easily. (Fig. S-1-3)
1. Using desoldering braid, remove the solder from
the foil of each pin of the flat pack-IC on the CBA
so you can install a replacement flat pack-IC more
easily.
2. Affix the wire to a workbench or solid mounting
point, as shown in Fig. S-1-5.
2. The “●” mark on the flat pack-IC indicates pin 1.
(See Fig. S-1-7.) Be sure this mark matches the 1
on the PCB when positioning for installation. Then
presolder the four corners of the flat pack-IC. (See
Fig. S-1-8.)
3. While heating the pins using a fine tip soldering
iron or hot air blower, pull up the wire as the solder
melts so as to lift the IC leads from the CBA
contact pads as shown in Fig. S-1-5.
3. Solder all pins of the flat pack-IC. Be sure that
none of the pins have solder bridges.
4. Bottom of the flat pack-IC is fixed with glue to the
CBA; when removing entire flat pack-IC, first apply
soldering iron to center of the flat pack-IC and heat
up. Then remove (glue will be melted). (Fig. S-1-6)
Example :
5. Release the flat pack-IC from the CBA using
tweezers. (Fig. S-1-6)
Note: When using a soldering iron, care must be
taken to ensure that the flat pack-IC is not
being held by glue. When the flat pack-IC is
removed from the CBA, handle it gently
because it may be damaged if force is applied.
Pin 1 of the Flat Pack-IC
is indicated by a " " mark.
Hot Air Blower
or
Fig. S-1-7
Presolder
Iron Wire
Soldering Iron
To Solid
Mounting Point
Fig. S-1-5
Flat Pack-IC
CBA
CBA
Fig. S-1-8
Fine Tip
Soldering Iron
Flat Pack-IC
Tweezers
Fig. S-1-6
3-3
TVN_SN
Instructions for Handling Semiconductors
Electrostatic breakdown of the semi-conductors may
occur due to a potential difference caused by
electrostatic charge during unpacking or repair work.
1. Ground for Human Body
Be sure to wear a grounding band (1 MΩ) that is
properly grounded to remove any static electricity that
may be charged on the body.
2. Ground for Workbench
Be sure to place a conductive sheet or copper plate
with proper grounding (1 MΩ) on the workbench or
other surface, where the semi-conductors are to be
placed. Because the static electricity charge on
clothing will not escape through the body grounding
band, be careful to avoid contacting semi-conductors
with your clothing.
<Incorrect>
CBA
<Correct>
Grounding Band
1MΩ
CBA
1MΩ
Conductive Sheet or
Copper Plate
3-4
TVN_SN
CABINET DISASSEMBLY INSTRUCTIONS
1. Disassembly Flowchart
Note:
(1) Order of steps in procedure. When reassembling,
follow the steps in reverse order. These numbers
are also used as the Identification (location) No. of
parts in figures.
This flowchart indicates the disassembly steps for the
cabinet parts, and the CBA in order to gain access to
item(s) to be serviced. When reassembling, follow the
steps in reverse order. Bend, route and dress the
cables as they were.
(2) Parts to be removed or installed.
(3) Fig. No. showing procedure of part location
CAUTION!
(4) Identification of parts to be removed, unhooked,
unlocked, released, unplugged, unclamped, or
desoldered.
P = Spring, L = Locking Tab, S = Screw,
CN = Connector
* = Unhook, Unlock, Release, Unplug, or Desolder
e.g. 2(S-2) = two Screws (S-2),
2(L-2) = two Locking Tabs (L-2)
When removing the CRT, be sure to discharge the
Anode Lead of the CRT with the CRT Ground Wire
before removing the Anode Cap.
[1] Rear Cabinet
(5) Refer to the following "Reference Notes in the
Table."
[2] CRT CBA
Reference Notes in the Table
[4] DTV Module
CBA Unit
[3] Main CBA
1. Removal of the Rear Cabinet: Remove screws
7(S-1), 2(S-2) and (S-3) then slide the Rear
Cabinet backward.
[5] CRT
2. Removal of the CRT CBA: Disconnect CN1501
then pull the CRT CBA backward.
2. Disassembly Method
3. Removal of the Main CBA:
CAUTION: Discharge the Anode Lead of the CRT
with the CRT Ground Wire before removing the
Anode Cap.
Disconnect CN801, CN802, CN571 and CN691 on
the Main CBA and remove Anode Cap. Then slide
the Main CBA backward.
Removal
Step/
Loc.
No.
Part
Fig.
No.
Remove/*Unhook/
Unlock/Release/
Unplug/Unclamp/
Desolder
Note
[1]
Rear
Cabinet
D1
7(S-1), 2(S-2), (S-3)
D2
1
[2]
CRT CBA
D4
*CN1501
D5
2
[3]
Main CBA
D3 *CN801, *CN802,
D4 *CN571, *CN691,
D5 Anode Cap
3
[4]
DTV
Module
CBA Unit
D3 *CN901, *CN902,
D5 Module PCB Holder
4
[5]
CRT
D4 4(S-4)
5
↓
(1)
↓
(2)
↓
(3)
↓
(4)
4. Removal of the DTV Module CBA Unit: Remove
Module PCB Holder and disconnect CN901 and
CN902 on the DTV Module CBA Unit. Then
remove the DTV Module CBA Unit.
5. Removal of the CRT: Remove screws 4(S-4).
Then slide the CRT backward.
↓
(5)
4-1
P7150DC
(S-1)
[4] DTV Module CBA Unit
Module PCB
Holder
(S-1)
(S-1)
[3] Main CBA
(S-1)
(S-2)
(S-3)
Front Cabinet
[1] Rear Cabinet
Fig. D1
Fig. D3
Degaussing Coil
[2] CRT CBA
[1] Rear Cabinet
(S-1)
CRT
Ground Wire
(S-1)
Anode Cap
(S-4)
(S-2)
(S-4)
(S-3)
(S-1)
(S-4)
(S-1)
(S-1)
(S-4)
[5] CRT
Front Cabinet
Front Cabinet
Fig. D2
Fig. D4
4-2
P7150DC
TV Cable Wiring Diagram
DG691
DEGAUSSING COIL
SP802
CLN802
SP801
CLN801
MAIN CBA
CN802
WH301A
CN801
CN691
DTV MODULE CBA UNIT
CN902
CN102
TU11
TUNER
FLYBACK
TRANSFORMER CN571
CN101
T571
WH501A
CN901
TO CRT GROUND
AC601
AC CORD
CRT CBA
FOCUS
WH301B
CN1501
SCREEN
JK1501
JK1501
ANODE
WH501B
Fig. D5
4-3
P7150DC
ELECTRICAL ADJUSTMENT INSTRUCTIONS
How to enter the service mode:
General Note: “CBA” is abbreviation for
“Circuit Board Assembly.”
Service mode:
Note: Electrical adjustments are required after
replacing circuit components and certain
mechanical parts. It is important to perform
these adjustments only after all repairs and
replacements have been completed.
Also, do not attempt these adjustments unless
the proper equipment is available.
1. Use the service remote control unit.
2. Turn the power on. (Use main power on the TV
unit.)
3. Press [SLEEP] button on the service remote
control unit. Version of micro computer will display
on the CRT. (Ex: 058-0.06)
4. Check the display on the lower left is “3641” and if
it is not “3641,” set it at “3641” according to "Initial
Setting" on page 5-2.
Test Equipment Required
1. NTSC Pattern Generator (Color Bar W/White
Window, Red Color, Dot Pattern, Gray Scale,
Monoscope, Multi-Burst)
1. +B Adjustment
2. DC Voltmeter
Purpose: To obtain correct operation.
3. Oscilloscope: Dual-trace with 10:1 probe,
V-Range: 0.001~50 V/Div,
F-Range: DC~AC-60 MHz
Symptom of Misadjustment: The picture is dark and
the unit does not operate correctly.
4. Plastic Tip Driver
5. Remote control unit: Part No. NE601UE
6. DC power supply 13.2V/5A
How to make Service remote
control unit:
1. Prepare normal remote control unit. (Part No.
NE601UE)
Remove 3 Screws from the back lid. (Fig. 1-1)
Adj. Point
Mode
Input
TP601(+B)
J095(GND)
VR661
---
---
Tape
M. EQ.
Spec.
---
DC Voltmeter
+114±0.5 V DC.
Note: TP601, J095(GND), VR661 --- Main CBA
1. Connect DC Volt Meter to TP601 and J095(GND).
2. Adjust VR661 so that the voltage of TP601
becomes +114±0.5 V DC.
Screws
Remote control unit (bottom)
Test Point
Fig. 1-1
J1
2. Add J1 (Jumper Wire) to the remote control CBA.
(Fig. 1-2)
Remote Control CBA
Fig. 1-2
5-1
P7150EA
2. Initial Setting
General
2. Press [CH o / p] buttons on the service remote
control unit so that the value of “COLOR” (CLR)
becomes 58.
1. Enter the Service mode. (See page 5-1.)
S-CLR
2. Press [VOL n] button on the service remote
control unit. Display changes “C/D,” “7F,” “SOUND
TYPE,” “VIDEO,” “1000,” “YUV MEMORY,”
“TUNER A/M/S,” “QAM,” “DTV-H,” “D-SOUND,”
and “DL V-CHIP” cyclically when [VOL n] button is
pressed.
1. Press [MENU] button on the service remote
control unit. Then select “S-COLOR” (S-CLR)
display.
2. Press [CH o / p] buttons on the service remote
control unit so that the value of “S-COLOR” (SCLR) becomes 58.
3. To set the following each data value, press [CH o /
p] buttons on the service remote control unit.
C-CLR
1. Press [MENU] button on the service remote
control unit. Then select “C-COLOR” (C-CLR)
display.
7F --- Set to “FF.”
SOUND TYPE --- Set to “MONO.”
VIDEO --- Set to “V1/V2.”
2. Press [CH o / p] buttons on the service remote
control unit so that the value of “C-COLOR” (CCLR) becomes 66.
1000 (monitoring time) --- Set to “1000.”
YUV MEMORY --- Set to “OFF.”
TUNER A/M/S --- Set it by indication of TUNER
as follows
TNT
1. Press [MENU] button on the service remote
control unit. Then select “TINT” (TNT) display.
UTUNATSMS001: Set it in “M.”
UTUNATSSP001: Set it in “S.”
DTV-H --- Set to “B.”
2. Press [CH o / p] buttons on the service remote
control unit so that the value of “TINT” (TNT)
becomes 54.
D-SOUND --- Set to “STEREO.”
V-TNT
DL V-CHIP --- Set to “ON.”
1. Press [MENU] button on the service remote
control unit. Then select “V-TINT” (V-TNT) display.
QAM --- Set to “135.”
3. Setting for BRIGHT, CONTRAST,
COLOR, S-COLOR, C-COLOR,
TINT, V-TINT, S-TINT, C-TINT,
SHARP, S-SHARP, and C-SHARP
Data Values
2. Press [CH o / p] buttons on the service remote
control unit so that the value of “V-TINT” (V-TNT)
becomes 58.
S-TNT
1. Press [MENU] button on the service remote
control unit. Then select “S-TINT” (S-TNT) display.
General
2. Press [CH o / p] buttons on the service remote
control unit so that the value of “S-TINT” (S-TNT)
becomes 58.
1. Enter the Service mode. (See page 5-1.)
2. Press [MENU] button on the service remote
control unit. Display changes “BRT,” “CNT,” “CLR,”
“S-CLR,” “C-CLR,” “TNT,” “V-TNT,” “S-TNT,” “CTNT,” “SHARP,” “S-SRP,” and “C-SRP,” cyclically
when [MENU] button is pressed.
C-TNT
1. Press [MENU] button on the service remote
control unit. Then select “C-TINT” (C-TNT) display.
2. Press [CH o / p] buttons on the service remote
control unit so that the value of “C-TINT” (C-TNT)
becomes 59.
CNT
1. Press [MENU] button on the service remote
control unit. Then select “CONTRAST” (CNT)
display.
SHARP
1. Press [MENU] button on the service remote
control unit. Then select “SHARP” (SHARP)
display.
2. Press [CH o / p] buttons on the service remote
control unit so that the value of “CONTRAST”
(CNT) becomes 84.
2. Press [CH o / p] buttons on the service remote
control unit and select “43.”
CLR
1. Press [MENU] button on the service remote
control unit. Then select “COLOR” (CLR) display.
S-SRP
1. Press [MENU] button on the service remote
control unit. Then select “S-SHARP” (S-SRP)
display.
5-2
P7150EA
2. Press [CH o / p] buttons on the service remote
control unit and select “40.”
7. SD Check Mode
C-SRP
2. Press [1] button on the remote control unit. The
unit enters the SD-Check mode.
1. Enter the Service mode. (See page 5-1.)
1. Press [MENU] button on the service remote
control unit. Then select “C-SHARP” (C-SRP)
display.
3. The unit starts selecting the added channel from
the first channel according to the memorized CH
ADD/DEL data and CATV/TV data in RAM.
2. Press [CH o / p] buttons on the service remote
control unit and select “40.”
Note: BRIGHT data value does not need to be
adjusted at this moment.
SD Check mode (Factory mode)
Press [1] button.
4. H f0 Adjustment
Purpose: To get correct horizontal frequency.
7
Please wait
Note: Use service remote control unit.
1. Press [2] button on the service remote control unit
and select H-ADJ mode. (By pressing [2] button
the display will change from TV AGC to H-ADJ.)
OSD color:
Magenta
When the selected
channel is not SD,,,,
2. Press [CH o / p] buttons on the service remote
control unit so that display will change “0” ~ “7”. At
this moment, Choose “4”.
13
Please wait
When all
channels
are SD,,,,
3. Turn the power off and on again. (Main Power
button on the TV unit.)
OSD color:
Magenta
5. Black Stretch Control Adjustment
Purpose: To show the fine black color.
26
OK
Symptom of Misadjustment: Black color will not
appear correctly.
30
NG
OSD color:
Magenta
Note: Use service remote control unit.
OSD color:
Magenta
1. Enter the Service mode. (See page 5-1.)
When SD-Check starting,
there is no ADD channel.
2. Press [0] button on the service remote control unit.
“B-S” is indicated.
3. Press [CH o / p] buttons on the service remote
control unit so that display will change “OFF,” “0,”
and “1.” Then choose “B-S OFF.”
ADD nothing
4. Press [0] button on the service remote control unit.
“B-S2” is indicated.
OSD color:
Magenta
5. Press [CH o / p] buttons on the service remote
control unit so that display will change “0” and “1.”
Then choose “B-S2 0.”
6. Turn the power off and on again, using the main
power button on the TV unit.
6. Purity Check
1. Enter the Service mode. (See page 5-1.)
2. Press [7] button on the remote control unit. Each
time pressing [7] button on the service remote
control unit, display changes Red mode, Green
mode, Blue mode, and White mode cyclically.
3. Select White mode.
4. Turn the power off and on again. (Main power
button on the TV unit.)
5-3
P7150EA
8. H. Position Adjustment
10. V. Position Adjustment
Purpose: To obtain correct horizontal position of
screen image.
Purpose: To obtain correct vertical width of screen
image.
Symptom of Misadjustment: If H. Position is
incorrect, horizontal position of image on the screen
may not be properly displayed.
Symptom of misadjustment: If V. Position is
incorrect, vertical height of image on the screen may
not be properly displayed.
Test Point
Adj. Point
Mode
Input
Test Point
Adj. Point
Mode
Input
---
[CH o / p]
buttons
RF
Monoscope
---
[CH o / p]
buttons
RF
Monoscope
Tape
M. EQ.
Spec.
Tape
M. EQ.
Spec.
---
Monoscope
90±5%
---
Monoscope
See below.
Note: Use service remote control unit
Note: Use service remote control unit
1. Operate the unit for at least 20 minutes.
1. Operate the unit for at least 20 minutes.
2. Enter the Service mode. (See page 5-1.)
2. Enter the Service mode. (See page 5-1.)
3. Receive the monoscope pattern.
3. Receive the monoscope pattern.
4. Press [8] button on the remote control unit. “H-P”
is indicated.
4. Press [9] button on the service remote control unit
and select “V-P” mode. (Display changes “V-S”
and “V-P” cyclically when [9] button is pressed).
5. Press [CH o / p] buttons on the service remote
control unit so that the monoscope pattern will be
90±5% of display size and the circle is round.
5. Press [CH o / p] buttons on the service remote
control unit so that the top and bottom of the
monoscope pattern will be equal each other.
6. Turn the power off and on again. (Main power
button on the TV unit.)
6. Turn the power off and on again. (Main power
button on the TV unit.)
9. V. Size Adjustment
11. Software Reset
Purpose: To obtain correct vertical width of screen
image.
To reset software, press [5] button on the remote
control unit for at least 5 seconds after pressing [CH
RETURN] button on the remote control unit.
Symptom of Misadjustment: If V. Size is incorrect,
vertical size of image on the screen may not be
properly displayed.
Test Point
Adj. Point
Mode
Input
---
[CH o / p]
buttons
RF
Monoscope
Tape
M. EQ.
Spec.
---
Monoscope
90±5%
Note: Use service remote control unit.
1. Operate the unit for at least 20 minutes.
2. Enter the Service mode. (See page 5-1.)
3. Receive the monoscope pattern.
4. Press [9] button on the service remote control unit
and select “V-S” mode. (Display changes “V-S”
and “V-P” cyclically when [9] button is pressed).
5. Press [CH o / p] buttons on the service remote
control unit so that the monoscope pattern will be
90±5% of display size and the circle is round.
6. Turn the power off and on again. (Main power
button on the TV unit.)
5-4
P7150EA
12. Cut-off Adjustment
6. Press [3] button. The display will momentarily
show “CUT OFF B” (B = Blue). Adjust the Blue cut
off by pressing [CH o / p] buttons. When done
with steps 4, 5 and 6 the horizontal line should be
pure white, if not, then attempt the Cut off
adjustment again.
Purpose: To adjust the beam current of R, G, B, and
screen voltage.
Symptom of Misadjustment: White color may be
reddish, greenish or bluish.
Test Point
Adj. Point
Mode
Input
---
Screen-Control
[CH o / p]
buttons
RF
Black
Raster
Tape
M. EQ.
Spec.
---
Pattern
Generator
See Reference
Notes below.
13. White Balance Adjustment
Purpose: To mix red, green and blue beams correctly
for pure white.
Symptom of Misadjustment: White becomes bluish
or reddish.
Test Point
Adj. Point
Screen
[CH o / p]
buttons
Tape
M. EQ.
Spec.
---
Pattern
Generator,
Color Analyzer
See below
Figure
Mode
Input
RF
White
Raster
(APL
100%)
Pattern Generator
Figure
Ext. Input
Fig. 2
Note: Screen Control FBT --- Main CBA
FBT = Fly Back Transformer
Use service remote control unit
Color Analyzer
1. Degauss the CRT and allow CRT to operate for 20
minutes before starting the alignment.
Fig. 3
2. Input the Black Raster Signal from RF Input.
Note: Use service remote control unit
3. Enter the Service mode. (See page 5-1.)
1. Operate the unit more than 20 minutes.
4. Press [VOL n] button on the service remote
control unit and select “C/D” mode. (Display
changes “C/D,” “7F,” “SOUND TYPE,” “VIDEO,”
“1000,” “YUV MEMORY,” “TUNER A/M/S,” “QAM,”
“DTV-H,” “D-SOUND,” and “DL V-CHIP” cyclically
when [VOL n] button is pressed.) then press “1.”
The display will momentarily show “CUT OFF R”
(R= Red). Now there should be a horizontal line
across the center of the picture tube. If needed,
turn the screen control on the flyback in a
clockwise direction gradually until the horizontal
line appears. Adjust the Red Cut off by pressing
[CH o / p] buttons. Proceed to Step 5 when the
Red Cut off adjustment is done.
2. Face the unit to east. Degauss the CRT using
Degaussing Coil.
3. Input the White Raster (APL 100%).
4. Set the color analyzer to the CHROMA mode and
after zero point calibration, bring the optical
receptor to the center on the tube surface (CRT).
5. Enter the Service mode. (See page 5-1.) Press
[VOL n] button on the service remote control unit
and select “C/D” mode. (Display changes “C/D,”
“7F,” “SOUND TYPE,” “VIDEO,” “1000,” “YUV
MEMORY,” “TUNER A/M/S,” “QAM,” “DTV-H,” “DSOUND,” and “DL V-CHIP” cyclically when [VOL
n] button is pressed). Then press [8] button on the
service remote control unit.
5. Press [2] button. The display will momentarily
show “CUT OFF G” (G = Green). Adjust the Green
Cut off by pressing [CH o / p] buttons. Proceed to
step 6 when the Green Cut off adjustment is done.
6. Press [4] button on the service remote control unit
for Red adjustment. Press [5] button on the
service remote control unit for Blue adjustment.
7. In each color mode, Press [CH o / p] buttons to
adjust the values of color.
5-5
P7150EA
8. Adjust Red and Blue color so that the temperature
becomes 9200K (x: 286 / y: 294)±3%.
15. Sub-Brightness Adjustment
9. At this time, Re-check if Horizontal line is white. If
not, Re-adjust Cut-off Adjustment until the
Horizontal Line becomes pure white.
Purpose: To get proper brightness.
Symptom of Misadjustment: If Sub-Brightness is
incorrect, proper brightness cannot be obtained by
adjusting the Brightness Control.
10. Turn off and on again to return to the normal
mode. Receive APL 100% white signal and Check
Chroma temperatures become 9200K (x: 286 / y:
294)±3%.
Note: Confirm that Cut Off Adj. is correct after this
adjustment, and attempt Cut Off Adj, if
needed.
14. YUV Pedestal Adjustment
Test Point
Adj. Point
Mode
Input
---
[CH o / p]
buttons
RF
IQW
Tape
M. EQ.
Spec.
---
Pattern
Generator
See below
Figure
Purpose: To adjust the pedestal level of YUV input.
Test Point
Adj. Point
Mode
Input
Screen
[CH o / p]
buttons
DTV
---
Tape
M. EQ.
Spec.
---
Color Analyzer
See below
White
Black
This bar
just
visible
Figure
Fig. 5
Note: IQW Setup level --- 7.5 IRE
Use service remote control unit
1. Enter the Service mode. (See page 5-1.) Then
input IQW signal from RF Input.
2. Press [MENU] button on the service remote
control unit and Select “BRT” mode. (Display
changes “BRT,” “CNT,” “CLR,” “S-CLR,” “C-CLR,”
“TNT,” “V-TNT,” “S-TNT,” “C-TNT,” “SHARP,” “SSRP,” and “C-SRP,” cyclically when [MENU] button
is pressed). Press [CH o / p] buttons so that the
bar is just visible (See above figure).
Color Analyzer
Fig. 4
1. Enter the Service mode in DTV mode.
2. Press [3] button on the service remote control unit.
The screen changes white 50% automatically.
(Display changes “U-PED” and “Y-PED” cyclically
when [3] button is pressed).
3. Turn the power off and on again. (Main power
button on the TV unit.)
3. Press [CH o / p] buttons on the service remote
control unit so that the Chroma temperature
becomes 9200K ±3%.
16. Focus Adjustment
Purpose: Set the optimum Focus.
Symptom of Misadjustment: If Focus Adjustment is
incorrect, blurred images are shown on the display.
Test Point
Adj. Point
Mode
Input
---
Focus Control
---
Monoscope
Tape
M. EQ.
Spec.
---
Pattern
Generator
See below
Note: Focus VR (FBT) --- Main CBA,
FBT = Fly Back Transformer
1. Operate the unit more than 30 minutes.
5-6
P7150EA
2. Face the unit to the East and Degauss the CRT
using Degaussing Coil.
18. Convergence Adjustment
3. Input the Monoscope Pattern.
Purpose: To obtain proper convergence of red, green
and blue beams.
4. Adjust the Focus Control on the FBT to obtain
clear picture.
Symptom of Misadjustment: If Convergence
Adjustment is incorrect, the edge of white letters may
have color edges.
The following adjustments normally are not
attempted in the field. Only when replacing the
CRT then adjust as a preparation.
17. Purity Adjustment
Test Point
Adj. Point
Mode
Input
---
C.P. Magnet (RB)
C.P. Magnet (RB-G)
Deflection Yoke
---
Dot Pattern
or
Crosshatch
Tape
M. EQ.
Spec.
---
Pattern Generator
See below
Purpose: To obtain pure color.
Symptom of Misadjustment: If Color Purity
Adjustment is incorrect, large areas of color may not
be properly displayed.
Figure
Test Point
Adj. Point
Mode
Input
---
Deflection Yoke
Purity Magnet
---
Red Color
Tape
M. EQ.
Spec.
---
Pattern
Generator
See below
CRT
COIL SCREW PURITY RB
RB-G
RING LOCK
SCREW
DY WEDGE
Figure
C.P. MAGNET CLAMPER
C.P. MAGNET
COIL CLAMPER
DEFLECTION YOKE
GREEN
RED
Fig. 7
BLUE
C.P. MAGNET (RB)
R
R
Fig. 6
G
1. Set the unit facing east.
G
B
2. Operate the unit for over 30 minutes before
adjusting.
B
Fig. 8
3. Fully degauss the unit using an external
degaussing coil.
C.B. MAGNET (RB-G)
4. Loosen the screw on the Deflection Yoke Clamper
and pull the Deflection Yoke back away from the
screen. (See Fig. 7)
RB
5. Loosen the Ring Lock and adjust the Purity
Magnets so that a red field is obtained at the
center of the screen. Tighten Ring Lock. (See Fig.
6,7)
RB
G
G
Fig. 9
6. Slowly push the Deflection Yoke toward the bell of
CRT and set it where a uniform red field is
obtained.
1. Loosen the Ring Lock and align red with blue dots
or Crosshatch at the center of the screen by
rotating (RB) C.P. Magnets. (See Fig. 8)
7. Tighten the clamp screw on the Deflection Yoke.
2. Align red / blue with green dots at the center of the
screen by rotating (RB-G) C.P. Magnet. (See Fig.
9)
3. Paintlock the C.P. Magnets after adjustment.
5-7
P7150EA
4. Remove the DY Wedges and slightly tilt the
Deflection Yoke horizontally and vertically to
obtain the best overall convergence.
5. Fix the Deflection Yoke by carefully inserting the
DY Wedges between CRT and Deflection Yoke.
5-8
P7150EA
HOW TO INITIALIZE THE TELEVISION
To put the program back at the factory-default,
initialize the television as the following procedure.
1. Use the service remote control unit.
2. Turn the power on. (Use main power on the TV
unit.)
3. Press [SLEEP] button on the service remote
control unit to enter the Service mode. (Refer to
“How to enter the Service mode” on page 5-1.)
4. Press [VOL n] button on the service remote
control unit twice, and confirm that OSD indication
is “7F = FF.” If needed, set it to become “7F = FF”
by pressing [CH o / p] buttons on the service
remote control unit.
5. Confirm that OSD indication on the four corners
on TV screen changes from on and off light
indication to red by pressing a [DISPLAY] button.
(It takes one or two seconds.)
6. Turn the power off by pressing main power button
on the TV unit, and unplug the AC cord from the
AC outlet.
6-1
P7150INT
SCL
SDA
SDA 5
7-1
204
153
154
155
38
DTV MODULE CBA UNIT
DTV-S-RESET
DTV-S-SOUT
DTV-S-SIN
DTV-S-SCLK
DTV-S-SREQ
IC101
(DTV SIGNAL PROCESS)
TO DTV MODULE
BLOCK DIAGRAM
CS 7
SCL 6
IC901 (MEMORY)
CN101
12
10
9
8
7
DTV-S-RESET
DTV-S-SOUT
DTV-S-SIN
DTV-S-SCLK
DTV-S-SREQ
Q911
SWITCHING
CN901
12
10
9
8
7
Q912
SWITCHING
13
59
58
57
54
DTV-S-RESET
DTV-S-SOUT
DTV-S-SIN
DTV-S-SCLK
DTV-S-SREQ
55 BUS-CONT
79 SDA
77 SCL
78 I2C-OPEN
IC111
TV MICON/VIDEO
/AUDIO/CHROMA
/DEFLECTION
56
14
28
20
39
76
6
7
8
PROTECT-1
PROTECT-2
PROTECT-3
80
65
2
75
9
4
RESET
DTV-ON-H
+5.7V-CTRL
MCU+5.7V-CTRL
+8.7V-CTRL
P-ON-H
INPUT-0
INPUT-1
VOLUME
AUDIO-MUTE
KEY-IN1
RCV-IN
Q131
KEY
SWITCH
REMOTE
SENSOR
RCV101
SWITCHING
Q161
SWITCHING
MAIN CBA
PROTECT-1
PROTECT-2
PROTECT-3
RESET
DTV-ON-H
+5.7V-CTRL
MCU+5.7V-CTRL
+8.7V-CTRL
P-ON-H
INPUT-0
INPUT-1
VOLUME
AUDIO-MUTE
TO CRT/H.V.
BLOCK DIAGRAM
TO POWER SUPPLY
BLOCK DIAGRAM
TO AUDIO
BLOCK DIAGRAM
System Control Block Diagram
BLOCK DIAGRAMS
P7151BLS
7-2
DTV-Y
DTV-Cb
DTV-Cr
JK721
S-VIDEO-IN C
TO DTV
MODULE
BLOCK
DIAGRAM
JK701
VIDEO-IN2
(FRONT)
JK742
VIDEO-IN1
(REAR)
IF 7
TU11
(TUNER UNIT)
Y
WF12
SAW
FILTER
SF11
11
AMP
RF
AGC
OSD
BASE BAND
TINT Cr/Cb
CLMP/AMP
/DELAY
VIDEO
SW
AFT-IN
63
13
AFT
VCO
VIDEO
DET
(IF SIGNAL PROCESS)
VIF
AMP
IC111
TV MICON/VIDEO
/AUDIO/CHROMA
/DEFLECTION
IC31
53 S-SW
30
29
62
17
25
26
27
35
21
23
32
16
17
4
LPF
V-SYNC
PROCESS
CIRCUIT
H-SYNC
PROCESS
CIRCUIT
CHROMA
COMB
CHROMINANCE
PROCESS
CIRCUIT
18
7
2
VCXO
WF13
LUMINANCE
PROCESS
CIRCUIT
IF AGC DET
LPF
4.5MHz
FILTER
CF32
4.5MHz
TRAP
CF31
RGB MATRIX
/COLOR CONT
X301
3.58MHz
FM
DET
EQ
AMP
6
9
WF14
OSD SW
/CONTRAST
/BRIGHTNESS
VCO F/B
AF
AMP
1
RGB DRIVE
/CUT OFF
/H.V. BLK
Q31
SWITCHING
EXT-H
80
MAIN CBA
16
44
43
37
36
49
48
47
IF SIGNAL
ACL
H-DRIVE
FBP-IN
V-RAMP-OUT
V-RAMP-F/B
WH301A
5 BLUE
4 GREEN
3 RED
TU-AUDIO
VIDEO SIGNAL
TO CRT/H.V.
BLOCK DIAGRAM
TO CRT/H.V.
BLOCK DIAGRAM
WH301B
TO AUDIO
BLOCK DIAGRAM
AUDIO SIGNAL
IF/Video Block Diagram
P7151BLIF
7-3
JK703
AUDIO(R)
-IN2
(FRONT)
JK702
AUDIO(L)
-IN2
(FRONT)
AUDIO(R)
-IN1
(REAR)
AUDIO(L)
-IN1
(REAR)
TO DTV
MODULE
BLOCK
DIAGRAM
JK743
DIGITAL
AUDIO-OUT
TO
IF/VIDEO
BLOCK
DIAGRAM
JK742
DTV-SPDIF
DTV-AUDIO(L)
DTV-AUDIO(R)
TU-AUDIO
MAIN CBA
9 10
SW CTL
(R-CH)
TUNER
4
AUDIO1
2
AUDIO2
1
DTV
5
11
15
12
14
(L-CH)
TUNER
AUDIO1
AUDIO2
DTV
3
13
IC701 (INPUT SELECT)
8
3
(R-CH)
(L-CH)
IC801 (AUDIO AMP)
P-ON+5V
2
MUTE
/STANDBY
CONTROL
7
11
14
Q811
AUDIO MUTE
AMP
VOLUME
AMP
AUDIO-MUTE
VOLUME
INPUT-0
INPUT-1
TO SYSTEM
CONTROL BLOCK
DIAGRAM
CLN802
CN802
SP-R 1
GND 2
CN801 CLN801
SP-L 1
SP-GND 2
AUDIO SIGNAL
SP802
SPEAKER
R-CH
JK801
HEADPHONE
JACK
SP801
SPEAKER
L-CH
Audio Block Diagram
P7151BLA
SCL 4
SDA 5
DIF-OUT1 10
DIF-OUT2 11
DIF-AGC 8
TU11
(TUNER UNIT)
CN902
11 DIF-OUT1
12 DIF-OUT2
9 DIF-AGC
ADC
/AGC I/F
4 XIN-25MHz
5 XOUT-25MHz
14 XIN-27MHz
15 XOUT-27MHz
174
178
140
7-4
DTV MODULE CBA UNIT
FLASH
MEMORY
I/F
SDRAM
I/F
MAIN CBA
DDR SDRAM
IC201 (DDR SDRAM)
159
158
162
161
156
182
187
186
*8
*7
*6
*5
*4
*3
*2
*1
SDA 144
SCL 143
BUS-CONT 41
AUDIO
DECODER
VIDEO
ENCODER
FLASH MEMORY
IC202 (FLASH MEMORY)
SYSTEM DECODER
/VIDEO DECODER
/VIDEO FORMAT
CONVERTER
/2D GRAPHICS
DIGITAL SIGNAL
PROCESS
IC101 (DTV SIGNAL PROCESS)
*1 79~81,85,87,89~91,92,94,96~98,
102,104,106
*2 55,56,58,60,61,116,119,120,124,
125,127,129,130
*3 1,2,7~12,20,206,209,211,213~216,
*4 23~25,27,29,32~36,41~44,47,48,50,
52~54,205
*5 1~9,16~25,48
*6 29~36,38~45
*7 28~32,35~42
*8 2,4,5,7,8,10,11,13,54,56,57,59,60,
62,63,65
25MHz
OSC
X281
27MHz
OSC
X271
CN102
11
LPF
12
9
Q245
BUFFER
BUFFER
ADDRESS BUS(1-20)
DATA BUS(0-15)
ADDRESS BUS(0-12)
CN102
18
19
20
15
16
Q214
Q213
CN101
2
14
15
Q212
SW
5
Q211
SW
4
L-CH
AUDIO
15
D/A
R-CH
CONVERTER
14
DATA BUS(0-15)
Q251
6
5
7
8
BUFFER
BUFFER
IC252
(AUDIO D/A CONVERTER)
Q244
Q243
DTV-SPDIF
SDA
SCL
TU-SDA
TU-SCL
CN901
2
14
15
5
4
DTV-Y
DTV-Cr
DTV-Cb
SDA
SCL
DTV-SPDIF
DTV-AUDIO(R)
TO SYSTEM
CONTROL
BLOCK
DIAGRAM
TO AUDIO
BLOCK
DIAGRAM
TO
IF/VIDEO
BLOCK
DIAGRAM
AUDIO SIGNAL
DTV-AUDIO(L)
VIDEO SIGNAL
CN902
DTV-Y
18
DTV-Cr
19
DTV-Cb
20
DTV-AUDIO(L) 15
DTV-AUDIO(R) 16
IF SIGNAL
DTV Module Block Diagram
P7151BLDTV
7-5
FBP-IN
ACL
WH301B
RED 3
GREEN 4
BLUE 5
TO IF/VIDEO
BLOCK DIAGRAM
WH301A
PROTECT-1
PROTECT-2
PROTECT-3
TO
SYSTEM CONTROL
BLOCK DIAGRAM
WF7
Q572
H.DRIVE
TO IF/VIDEO
BLOCK DIAGRAM
DEF+B
+B
H-DRIVE
TO POWER SUPPLY
BLOCK DIAGRAM
TO IF/VIDEO
BLOCK DIAGRAM
V-RAMP-F/B
V-RAMP-OUT
T572
WF8
H.OUTPUT
Q571
MAIN CBA
7
4
10
3
5
2
1
WF1
8
1
7
Q1511
RED AMP
T571 F.B.T.
WF15
11
S
F
HV
FOCUS VR
3
CRT CBA
WF4
WF2
PULSE
UP
SCREEN VR
6
AMP
THERMAL
PROTECTION
FOCUS
SCREEN
ANODE
WF5
WF3
WF11 WH501A
3 HEATER
1 +200V
GREEN AMP
Q1521
5
IC551 (V-DEFLECTION CONTROL)
BLUE AMP
Q1531
WH501B
3
1
WF6
1
3
4
5
CN1501
7
4
8
6
11
10
9
JK1501
CN571
WF9
WF10
VIDEO SIGNAL
V501
CRT
GND
HEATER
R
G
B
FOCUS
SCREEN
GND
ANODE
HDRIVE
VDRIVE
DY551 D.Y.
CRT/H.V. Block Diagram
P7151BLCRT
DG691
DEGAUSSING
COIL
AC601
AC CORD
CN691
F601
4A/125V
4A/125V
7-6
BRIDGE
RECTIFIER
D605 - D608
Q602
LIMITER
Q601
SWITCHING
PS691
LINE
FILTER
L601
HOT CIRCUIT. BE CAREFUL.
IC601
ERROR
VOLTAGE DET
HOT
2
3
5
7
3
4
T601
CAUTION !
Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit.
If Main Fuse (F601) is blown , check to see that all components in the power supply
circuit are not defective before you connect the AC plug to the AC power supply.
Otherwise it may cause some components in the power supply circuit to fail.
2
1
14
13
15
16
11
12
10
9
4A/125V
Q652
FEED
BACK
COLD
J095
MAIN CBA
+B ADJ
Q321
+9V REG.
Q674
SWITCHING
Q673
SWITCHING
Q672
SW+10V
Q111
SW+5V
Q322
SW+5V
IC905
SHUNT
REG.
Q903
SW+2.5V
IC911
SHUNT
REG.
Q910
SW+3.3V
Q904
SW+5V
Q681
SW+8V
Q902
SWITCHING
Q901
SW+7.5V
IC903
+1.8V REG.
VR661
GND
Q113
RESET
Q112
+3.3V REG.
Q682
SW+5V
TP601 +B
CN1001
3 DTV-ON+5V
DTV-ON-H
MCU+5.7V-CTRL
RESET
P-ON-H
P-ON+3.3V
P-ON+5V
AL+9V
+5.7V-CTRL
+8.7V-CTRL
P-ON+8V
P-ON+5V
AUDIO +B
P-ON+5V
DEF +B
AL+30V
+B
DTV-ON+5V
DTV-ON+3.3V
DTV-ON+2.5V
DTV-ON+1.8V
TO
SYSTEM
CONTROL
BLOCK
DIAGRAM
TO
SYSTEM
CONTROL
BLOCK
DIAGRAM
TO
SYSTEM
CONTROL
BLOCK
DIAGRAM
DTV MODULE
CBA UNIT
CN101
3
CN1002
CN102
4 DTV-ON+3.3V 4
5 DTV-ON+2.5V 5
6 DTV-ON+1.8V 6
CAUTION ! : For continued protection against risk of fire,
replace only with same type 4 A, 125V fuse.
ATTENTION : Utiliser un fusible de rechange de même type de 4A, 125V.
NOTE:
The voltage for parts in hot circuit is measured using
hot GND as a common terminal.
Power Supply Block Diagram
P7151BLP
SCHEMATIC DIAGRAMS / CBA'S AND TEST POINTS
Standard Notes
Many electrical and mechanical parts in this chassis have special characteristics. These characteristics often
pass unnoticed and the protection afforded by them cannot necessarily be obtained by using replacement
components rated for higher voltage, wattage, etc. Replacement parts that have these special safety
characteristics are identified in this manual and its supplements; electrical components having such features are
identified by the mark “#” in the schematic diagram and the parts list. Before replacing any of these components,
read the parts list in this manual carefully. The use of substitute replacement parts that do not have the same
safety characteristics as specified in the parts list may create shock, fire, or other hazards.
Notes:
1. Do not use the part number shown on these drawings for ordering. The correct part number is shown in the
parts list, and may be slightly different or amended since these drawings were prepared.
2. All resistance values are indicated in ohms (K = 103, M = 106).
3. Resistor wattages are 1/4W or 1/6W unless otherwise specified.
4. All capacitance values are indicated in µF (P = 10-6 µF).
5. All voltages are DC voltages unless otherwise specified.
Note of Capacitors:
ML --- Mylar Cap.
PP --- Metallized Film Cap.
SC --- Semiconductor Cap.
L --- Low Leakage type
Temperature Characteristics of Capacitors are noted with the following:
B --- ±10%
CH --- 0±60 ppm/°C
CSL --- +350~-1000 ppm/°C
Tolerance of Capacitors are noted with the following:
Z --- +80~-20%
Note of Resistors:
CEM --- Cement Res.
MTL --- Metal Res.
F --- Fuse Res.
Capacitors and transistors are represented by the following symbols.
CBA Symbols
Schematic Diagram Symbols
(Top View) (Bottom View)
+
Electrolytic Capacitor
Digital Transistor
(Bottom View)
Transistor or Digital Transistor
E
C
B
(Top View)
(Top View)
NPN Transistor
PNP Transistor
ECB
ECB
(Top View)
(Top View)
PNP Digital Transistor
NPN Digital Transistor
ECB
ECB
8-1
L17N_SC
LIST OF CAUTION, NOTES, AND SYMBOLS USED IN THE SCHEMATIC DIAGRAMS ON
THE FOLLOWING PAGES:
1. CAUTION:
CAUTION: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH SAME
TYPE_A,_V FUSE.
ATTENTION: UTILISER UN FUSIBLE DE RECHANGE DE MÊME TYPE DE_A,_V.
2. CAUTION:
Fixed Voltage (or Auto voltage selectable) power supply circuit is used in this unit.
If Main Fuse (F601) is blown, first check to see that all components in the power supply circuit are not
defective before you connect the AC plug to the AC power supply. Otherwise it may cause some components
in the power supply circuit to fail.
3. Note:
1. Do not use the part number shown on the drawings for ordering. The correct part number is shown in the
parts list, and may be slightly different or amended since the drawings were prepared.
2. To maintain original function and reliability of repaired units, use only original replacement parts which are
listed with their part numbers in the parts list section of the service manual.
4. Voltage indications on the schematics are as shown below:
Plug the TV power cord into a standard AC outlet.:
1
(Unit: Volt)
2
3
5.0
(3.0)
Voltage
5.0
(3.0)
Power on mode
Power off mode
Indicates that the voltage
is not consistent here.
5. How to read converged lines
1-D3
3
Distinction Area
Line Number
(1 to 3 digits)
AREA D3
2
Examples:
1. "1-D3" means that line number "1" goes to the line number
1
"1" of the area "D3".
2. "1-B1" means that line number "1" goes to the line number
"1" of the area "B1".
1-B1
AREA B1
1-D3
A
B
C
D
6. Test Point Information
: Indicates a test point with a jumper wire across a hole in the PCB.
: Used to indicate a test point with a component lead on foil side.
: Used to indicate a test point with no test pin.
: Used to indicate a test point with a test pin.
8-2
L17N_SC
Main 1/4 Schematic Diagram
8-3
P7151SCM1
Main 2/4 Schematic Diagram
8-4
P7151SCM2
Main 3/4 & CRT Schematic Diagram
8-5
P7151SCM3
Main 4/4 Schematic Diagram
CAUTION !
Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit.
If Main Fuse (F601) is blown , check to see that all components in the power supply
circuit are not defective before you connect the AC plug to the AC power supply.
Otherwise it may cause some components in the power supply circuit to fail.
4A/125V
CAUTION ! : For continued protection against risk of fire,
replace only with same type 4 A, 125V fuse.
ATTENTION : Utiliser un fusible de rechange de même type de 4A, 125V.
8-6
NOTE:
The voltage for parts in hot circuit is measured using
hot GND as a common terminal.
P7151SCM4
DTV Module 1/2 Schematic Diagram
8-7
P7151SCD1
DTV Module 2/2 Schematic Diagram
VOLTAGE CHART
CN101
Pin No.
Voltage
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
0
1.5
5.0
3.3
3.3
0
0
2.7
3.2
3.2
0
3.3
0
3.3
3.3
CN102
8-8
Pin No.
Voltage
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
--4.8
0
3.3
2.5
1.8
--0
0.5
0
0
0
0
--2.4
2.4
0
~
~
~
P7151SCD2
Main CBA Top View
CAUTION !
Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit.
If Main Fuse (F601) is blown , check to see that all components in the power supply
circuit are not defective before you connect the AC plug to the AC power supply.
Otherwise it may cause some components in the power supply circuit to fail.
TP601
+B
4A/125V
CAUTION ! : For continued protection against risk of fire,
replace only with same type 4 A, 125V fuse.
ATTENTION : Utiliser un fusible de rechange de même type de 4A, 125V.
Because a hot chassis ground is present in the power
supply circuit, an isolation transformer must be used.
Also, in order to have the ability to increase the input
slowly,when troubleshooting this type power supply
circuit, a variable isolation transformer is required.
NOTE:
The voltage for parts in hot circuit is measured using
hot GND as a common terminal.
FOCUS-VR
(UPPER SIDE)
SCREEN-VR
(LOWER SIDE)
VR661
+B ADJ
J095
GND
8-9
BP7150F01011-1
Main CBA Bottom View
CAUTION !
Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit.
If Main Fuse (F601) is blown , check to see that all components in the power supply
circuit are not defective before you connect the AC plug to the AC power supply.
Otherwise it may cause some components in the power supply circuit to fail.
4A/125V
CAUTION ! : For continued protection against risk of fire,
replace only with same type 4 A, 125V fuse.
ATTENTION : Utiliser un fusible de rechange de même type de 4A, 125V.
Because a hot chassis ground is present in the power
supply circuit, an isolation transformer must be used.
Also, in order to have the ability to increase the input
slowly,when troubleshooting this type power supply
circuit, a variable isolation transformer is required.
NOTE:
The voltage for parts in hot circuit is measured using
hot GND as a common terminal.
WF9
PIN 1
OF CN571
WF10
PIN 4
OF CN571
WF11
PIN 3
OF WH501A
WF8
Q571
Base
WF15
PIN 7
OF IC551
WF7
Q572
Collector
WF14
PIN 9
OF IC31
WF13
PIN 2
OF IC31
WF12
PIN 23
OF IC111
8-10
BP7150F01011-1
CRT CBA Top View
CRT CBA Bottom View
WF5
Q1521
Collector
8-11
WF2
Q1521
Bace
WF4
WF1
Q1511
Q1511
Collector Bace
WF6
WF3
Q1531
Q1531
Collector Bace
BP7150F01011-2
WAVEFORMS
WF1 ~ WF15 = Waveforms to be observed at
Waveform check points.
(Shown in Schematic Diagram.)
Input:
NTSC Color Bar Signal (with 1kHz Audio Signal)
INITIAL POSITION: Unplug unit from AC outlet for at least 5 minutes.
reconnect to AC outlet and then turn power on.
(Brightness---Center Color---Center Tint---Center Contrast---Approx 70%)
WF1
1DIV: 2V 20µs
Q 1511 Base
WF5
1DIV: 20V 20 µs
Q 1521 Collector
WF2
1DIV: 2V 20µs
Q 1521 Base
WF6
1DIV: 20V 20 µs
Q 1531 Collector
WF3
1DIV: 2V 20µs
Q 1531 Base
WF7
1DIV: 10V 20µs
Q 572 Collector
WF4
1DIV: 20V 20µs
Q 1511 Collector
WF8
1DIV: 5V 20µs
Q 571 Base
9-1
L17WF
WF1 ~ WF15 = Waveforms to be observed at
Waveform check points.
(Shown in Schematic Diagram.)
Input:
NTSC Color Bar Signal (with 1kHz Audio Signal)
INITIAL POSITION: Unplug unit from AC outlet for at least 5 minutes.
reconnect to AC outlet and then turn power on.
(Brightness---Center Color---Center Tint---Center Contrast---Approx 70%)
WF9
1DIV: 200V 20µs
CN 571 Pin 1
WF13 1DIV: 500mV 20µs
IC 31 Pin 2
WF10 1DIV: 10V 5ms
CN 571 Pin 4
WF14 1DIV: 500mV 200µs
IC 31 Pin 9
WF11 1DIV: 5V 20µs
WH 501A Pin 3
WF15 1DIV: 1V 5ms
IC 551 Pin 7
WF12 1DIV: 500mV 20µs
IC 111 Pin 23
9-2
L17WF
GND
CN1501
V501
CRT
FOCUS
CRT CBA
ANODE
SP802
SPEAKER
R-CH
SP801
SPEAKER
L-CH
10-1
5
4
3
2
1
VD
HD
DY551
D.Y.
AC601
AC CORD
WH501B
HEATER 3
GND 2
+200V 1
WH301B
BLUE
GREEN
RED
GND
CRT+8V
SCREEN
CLN802
CLN801
CLN501
CLN301
1
2
3
4
5
CN571
WH501A
3 HEATER
2 GND
1 +200V
5
4
3
2
1
WH301A
BLUE
GREEN
RED
GND
CRT+8V
CN691
CN691A
CN691B
CN802
1 SP-R
2 GND
CN801
1 SP-L
2 GND
T571
FBT
MAIN CBA
TU11 TUNER UNIT
CN902
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
CN901
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
NU
DTV-ON-H2
D-GND
DTV-ON+3.3V
DTV-ON+2.5V
DTV-ON+1.8V
SMART-ANT(NU)
A-GND
DIF-AGC
A-GND
DIF-OUT1
DIF-OUT2
A-GND
DTV-VIDEO(NU)
DTV-AUDIO(L)
DTV-AUDIO(R)
A-GND
DTV-Y
DTV-Cr
DTV-Cb
D-GND
DTV-SPDIF
DTV-ON+5V
TU-SCL
TU-SDA
D-GND
DTV-S-SREQ
DTV-S-SCLK
DTV-S-SIN
DTV-S-SOUT
D-GND
DTV-S-RESET
D-GND
SDA
SCL
CN102
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
CN101
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
DTV MODULE CBA UNIT
WIRING DIAGRAM
P7151WI
IC PIN FUNCTION DESCRIPTIONS
IC111 (TV Micro Controller)
Pin
No.
Signal Name
Pin
No.
Function
Signal Name
37 V-RAMP-OUT
Vertical Ramp Output
Vertical Ramp OSC Capacitor
+8.7V
REG.OUT
+8.7V Regulator Control Signal
Output
1
GND
GND
38 V-RAMP-CAP
2
VOLUME
Volume Control Signal Output
39
3
NU
Not Used
4
RCV-IN
Remote Control Signal Input
5
TEST0
GND
6
PROTECT-1
Power Supply Protection 1
7
PROTECT-2
Power Supply Protection 2
8
PROTECT-3
Power Supply Protection 3
9
KEY-IN1
Key Input 1
10 NU
Not Used
11 NU
Not Used
12 DTV-ON-H2
DTV On Signal 2 at High
13 DTV-S-RESET DTV Reset
14 DTV-ON-H
DTV On Signal at High
15 GND
GND
16 ACL
Automatic Contrast Limiter
17 Y-SW OUT
Composite Video Signal
Output
18 XTAL
Crystal Oscillation(3.58MHz)
19 C-APC
Chrominance APC
20
MCU +5.7V
REG.OUT
+5.7V Regulator Control Signal
Output
Function
40 H VCO F/B
Horizontal Vco Feed Back
41 AFC FILT
Horizontal AFC Filter
42 GND
GND
43 FBP-IN
Flyback Pulse Input
44 H-OUT
Horizontal Pulse Output
45 VCC(+8V)
+8V VCC
46 VCC(+8V)
+8V VCC
47 R-OUT
Red Signal Output
48 G-OUT
Green Signal Output
49 B-OUT
Blue Signal Output
50 RESET-OUT
Reset Output
51 NU
Not Used
52 NU
Not Used
53 S-SW
Detecting S-VIDEO Jack
Connection
54 DTV-S-SREQ
DTV Serial Request
55 BUS-CONT
BUS Control
56 RESET
Reset
57 DTV-S-SCLK
DTV Serial Clock
DTV Serial Data In
21 CVBS-IN3
Composite Video Signal 3
Input
58 DTV-S-SIN
59 DTV-S-SOUT
DTV Serial Data Out
22 V/C VCC
VCC
60 HLF
Horizontal Filter
23 CVBS-IN2
Composite Video Signal 2
Input
61 VHOLD
Vertical Hold
62 CV-IN
Composite Video Signal Input
24 GND
GND
63 AFT-IN
AFT Voltage Input
25 DTV-Y-IN
DTV Y Signal Input
64 DTV-PROTECT DTV Power Supply Protection
26 DTV-Cb-IN
DTV Cb Signal Input
65 INPUT-1
Input Select 1 Signal Output
27 DTV-Cr-IN
DTV Cr Signal Input
66 GND
GND
+5.7V
28
REG.OUT
+5.7V Regulator Control Signal
Output
67 NU
Not Used
29 C-IN[Y/C]
Chrominance Signal Input
68 NU
Not Used
30 Y-IN[Y/C]
Luminance Signal Input
69 GND
GND
31 VREG VCC
VCC
70 FILT
Filter
32 FSC-OUT
Clock Output
71 VDD(+5V)
+5V VDD
33 NU
Not Used
72 SPOT-KILL
Counter Measure for Spot
34 NU
Not Used
73 NU
Not Used
Not Used
35 CVBS-IN1
Composite Video Signal 1
Input
74 NU
75 AUDIO-MUTE
Audio Mute Signal Output
36 V-RAMP-F/B
Vertical Ramp Feed Back
76 P-ON-H
Power On Signal at High
11-1
P7150PIN
Pin
No.
Signal Name
Function
77 SCL
Serial Clock
78 I2C-OPEN
Chip Select
79 SDA
Serial Data
80
INPUT-0
/ EXT-H
Input Select Signal Output
/ External Input at High
11-2
P7150PIN
EXPLODED VIEWS
Cabinet
SHINWHA
TAPE SGT-730
(BLACK)
V501-1
L1
V501-2
Details for DY551
and surrounding parts
L1
SHINWHA
TAPE SGT-730
(WHITE)
A3
L1
DY551
L3
Scotch Tape #880
L2
B2
B4
L5
L1
L1
CLN551
DY551
CLN801
L4
L1
B5
SP801
L5
A2
CRT CBA
B4
L5
B2
L1
DG691
A1-1
DTV Module
CBA Unit
TB10
B2
TB7
Scotch
B1 Tape #880
TL2
TL2
TB9
TB16
L5
V501
TB16
B2
CLN802
L4
B5
AC601
SP802
Main CBA
A1-2
12-1
TB11
TL2
P7150CEX
Packing
S2
S7
X2
X3
S6
S3
Tape
X1
S1
Packing tape
S4
FR
ON
T
Packing tape
12-2
P7151PEX
MECHANICAL PARTS LIST
PRODUCT SAFETY NOTE: Products marked with a
# have special characteristics important to safety.
Before replacing any of these components, read
carefully the product safety notice in this service
manual. Don't degrade the safety of the product
through improper servicing.
NOTE: Parts that are not assigned part numbers
(---------) are not available.
Ref. No.
A1-1
Description
Part No.
FRONT CABINET L3314WQ
1EM121215
A1-2
CONTROL PLATE P7151UM
1EM322514
A2
REAR CABINET P7150UT
1EM021560
A3#
RATING LABEL P7151UM
----------
B1
TENSION SPRING P77B0UT
1EM424298
B2#
DEGAUSS HOLDER L2401UB
1EM420205
B4
CLOTH L9800UA 95X15XT 0 0.5
0EM405041
B5
SPEAKER HOLDER L2404UE
1EM420493
CLN551
CRT GND WIRE
WX1L7820-003
CLN801
WIRE ASSEMBLY
WX1L9200-001
CLN802
WIRE ASSEMBLY SPEAKER WIRE(180MM)
WX1L1131-001
DG691#
DEGAUSSING COIL (AL) ZTM054A
LLBH00ZTM069
DY551#
DEFLECTION YOKE ADY2101F
LLEY0ZAEC002
L1
SCREW P-TIGHT 4X18 BIND HEAD +
GBJP4180
L2
SCREW TAPPING M4X14
DBT14140
L3
SCREW P-TIGHT 3X10 BIND HEAD+
GBHP3100
L4
SCREW P-TIGHT 3X14 BIND HEAD +
GBJP3140
L5
SCREW L1500UA
0EM406142A
SP801
SPEAKER S08N04
DSD0808XQ013
SP802
SPEAKER S08N04
DSD0808XQ013
TB7
MODULE PCB HOLDER P7150UZ
1EM322373
TB16
CLOTH 10X65XT0.3
1EM420328
V501#
CRT A51LYX996X
TCRT190MS015
V501-1
C.P.MAGNET JH225-19C
XM04000BV016
V501-2
WEDGE FT-00110W
XV10000T4001
S1
CARTON P7151UM
1EM424200
S2
STYROFOAM TOP ASSEMBLY L2404UE
0EM409269
S3
STYROFOAM BOTTOM ASSEMBLY L2404UE
0EM409270
S4
RFID LABEL P7100UM
----------
S6
SET SHEET B7500UA 1000X1700
0EM402178
S7
HOLD PAD L1400UA
0EM406207
PACKING
ACCESSORIES
X1
BAG POLYETHYLENE 235X365XT0.03
0EM408420A
X2#
OWNERS MANUAL ENGLISH
1EMN22122
X3
REMOTE CONTROL NE601UE
NE601UE
20070111
13-1
P7151CA
ELECTRICAL PARTS LIST
PRODUCT SAFETY NOTE: Products marked with a
# have special characteristics important to safety.
Before replacing any of these components, read
carefully the product safety notice in this service
manual. Don't degrade the safety of the product
through improper servicing.
Ref. No.
C111
NOTES:
1. Parts that are not assigned part numbers (---------)
are not available.
2. Tolerance of Capacitors and Resistors are noted
with the following symbols.
C.....±0.25%
D.....±0.5%
F.....±1%
G.....±2%
J......±5%
K.....±10%
M.....±20%
N.....±30%
Z.....+80/-20%
DTV MODULE CBA UNIT
Ref. No.
Description
DTV MODULE CBA UNIT
Part No.
1ESA13966
MMA CBA
Ref. No.
Description
MMA CBA
Consists of the following:
Part No.
----------
MMA CBA (MAIN CBA + CRT CBA)
1ESA13844
T571#
TRANS FBT JF0501-3201-G or
LTF00CPXB049
#
TRANS FBT BSC23-2631S-G
LTF00CPS2063
MAIN CBA
Ref. No.
Description
MAIN CBA
Consists of the following:
Part No.
----------
CAPACITORS
Description
ELECTROLYTIC CAP. 47µF/16V M
Part No.
CE1CMASDL470
C112
ELECTROLYTIC CAP. 4.7µF/50V M
CE1JMASDL4R7
C113
CHIP CERAMIC CAP. F Z 0.1µF/50V
CHD1JZB0F104
C114
FILM CAP.(P) 0.001µF/50V J
CMA1JJS00102
C115
ELECTROLYTIC CAP. 0.1µF/50V M
CE1JMASDL0R1
C116
CERAMIC CAP.(AX) B K 220pF/50V
CCA1JKT0B221
C117
CHIP CERAMIC CAP. B K 0.01µF/50V
CHD1JKB0B103
C118
ELECTROLYTIC CAP. 47µF/16V M
CE1CMASDL470
C120
ELECTROLYTIC CAP. 100µF/10V M
CE1AMASDL101
C122
ELECTROLYTIC CAP. 100µF/10V M
CE1AMASDL101
C132
CHIP CERAMIC CAP. F Z 0.1µF/50V
CHD1JZB0F104
C133
CHIP CERAMIC CAP. F Z 0.01µF/50V
CHD1JZB0F103
C151
CHIP CERAMIC CAP. B K 220pF/50V
CHD1JKB0B221
C152
CHIP CERAMIC CAP. B K 220pF/50V
CHD1JKB0B221
C301
CHIP CERAMIC CAP. CH J 120pF/50V
CHD1JJBCH121
C302
ELECTROLYTIC CAP. 1µF/50V M
CE1JMASDL1R0
C303
CHIP CERAMIC CAP. B K 0.015µF/50V
CHD1JKB0B153
C304
CHIP CERAMIC CAP. F Z 0.1µF/50V
CHD1JZB0F104
C305
CHIP CERAMIC CAP. F Z 1µF/10V
CHD1AZB0F105
C306
ELECTROLYTIC CAP. 100µF/10V M
CE1AMASDL101
C309
CHIP CERAMIC CAP. F Z 0.1µF/50V
CHD1JZB0F104
C311
CHIP CERAMIC CAP. F Z 1µF/10V
CHD1AZB0F105
C312
CHIP CERAMIC CAP. F Z 0.1µF/50V
CHD1JZB0F104
C322
ELECTROLYTIC CAP. 0.47µF/50V M
CE1JMASDLR47
C324
ELECTROLYTIC CAP. 10µF/50V M
CE1JMASDL100
C325
CERAMIC CAP.(AX) SL J 12pF/50V
CCA1JJTSL120
C328
ELECTROLYTIC CAP. 10µF/50V M
CE1JMASDL100
C329
CHIP CERAMIC CAP. F Z 0.01µF/50V
CHD1JZB0F103
C330
METALIZED POLYESTER FILM CAP. 0.47µF/
50V J
CT1J474DT040
C331
CHIP CERAMIC CAP. B K 1000pF/50V
CHD1JKB0B102
C332
ELECTROLYTIC CAP. 10µF/50V M
CE1JMASDL100
C341
CHIP CERAMIC CAP. B K 0.01µF/50V
CHD1JKB0B103
C342
ELECTROLYTIC CAP. 1µF/50V M
CE1JMASDL1R0
C343
CHIP CERAMIC CAP. B K 0.01µF/50V
CHD1JKB0B103
C345
ELECTROLYTIC CAP. 1000µF/10V M
CE1AMASDL102
C353
ELECTROLYTIC CAP. 1µF/50V M
CE1JMASDL1R0
C422
CHIP CERAMIC CAP. F Z 1µF/16V
CHD1CZB0F105
C12
ELECTROLYTIC CAP. 100µF/10V M
CE1AMASDL101
C427
CHIP CERAMIC CAP. F Z 1µF/16V
CHD1CZB0F105
C16
CERAMIC CAP.(AX) B 0.01µF/50V
CCK1JKT0B103
C501
FILM CAP.(P) 0.1µF/50V J
CMA1JJS00104
C21
CERAMIC CAP.(AX) B K 1000pF/50V
CCA1JKT0B102
C502
CERAMIC CAP.(AX) B K 1000pF/50V
CCA1JKT0B102
C31
ELECTROLYTIC CAP. 100µF/10V M
CE1AMASDL101
C503
ELECTROLYTIC CAP. 47µF/35V M
CE1GMASDL470
C34
ELECTROLYTIC CAP. 0.47µF/50V M
CE1JMASDLR47
C504
ELECTROLYTIC CAP. 1µF/50V LL
CE1JMASLH1R0
C36
CHIP CERAMIC CAP. B K 1000pF/50V
CHD1JKB0B102
C505
ELECTROLYTIC CAP. 1000µF/25V M
CE1EMZPDL102
C37
ELECTROLYTIC CAP. 1µF/50V M
CE1JMASDL1R0
C506
ELECTROLYTIC CAP. 470µF/35V M
CE1GMZADL471
C40
CERAMIC CAP BK0.039µF/50V
CA1J393TU011
C507
FILM CAP.(P) 0.047µF/50V J
CMA1JJS00473
C41
ELECTROLYTIC CAP. 0.47µF/50V M
CE1JMASDLR47
C509
FILM CAP.(P) 0.015µF/50V J
CMA1JJS00153
C42
CHIP CERAMIC CAP. B K 0.033µF/50V
CHD1JKB0B333
C520#
ELECTROLYTIC CAP. 4.7µF/50V M
CE1JMASDL4R7
C51
CHIP CERAMIC CAP. B K 1000pF/50V
CHD1JKB0B102
C566#
CERAMIC CAP. 1200pF/2KV
CA3D122PAN04
CA3C822VC011
C52
CHIP CERAMIC CAP. F Z 0.01µF/50V
CHD1JZB0F103
C567#
P.P. CAP 0.0082µF/1.6K J
C53
ELECTROLYTIC CAP. 100µF/10V M
CE1AMASDL101
C571
P.P.CAP 0.27µF/200 J
CA2D274VC012
C54
CHIP CERAMIC CAP. B K 1000pF/50V
CHD1JKB0B102
C574#
ELECTROLYTIC CAP. 4.7µF/250V M
CE2EMASDL4R7
C55
CHIP CERAMIC CAP. F Z 0.01µF/50V
CHD1JZB0F103
C577
ELECTROLYTIC CAP. 47µF/35V M
CE1GMASDL470
C57
CHIP CERAMIC CAP. B K 0.047µF/50V
CHD1JKB0B473
C578
FILM CAP.(P) 0.01µF/50V J
CMA1JJS00103
CE2CMASDL1R0
C58
CHIP CERAMIC CAP. B K 0.033µF/50V
CHD1JKB0B333
C584#
ELECTROLYTIC CAP. 1µF/160V M
C71
CHIP CERAMIC CAP. CH J 47pF/50V
CHD1JJBCH470
C585
CERAMIC CAP. B K 100pF/500V
CCD2JKS0B101
C72
CHIP CERAMIC CAP. CH J 47pF/50V
CHD1JJBCH470
C588#
ELECTROLYTIC CAP. 47µF/160V M W/F
CE2CMZNDL470
CE1JMASDL100
C73
CHIP CERAMIC CAP. F Z 0.01µF/50V
CHD1JZB0F103
C594#
ELECTROLYTIC CAP. 10µF/50V M
C78
CHIP CERAMIC CAP. B K 1000pF/50V
CHD1JKB0B102
C601#
METALIZED FILM CAP. 0.33µF/250V
CT2E334MS037
C104
ELECTROLYTIC CAP. 10µF/50V M
CE1JMASDL100
C605
CERAMIC CAP. F Z 0.01µF/500V
CCD2JZP0F103
20070111
14-1
P7151EL
Ref. No.
C606
Description
CERAMIC CAP. F Z 0.01µF/500V
Part No.
Ref. No.
Description
Part No.
CCD2JZP0F103
D113
ZENER DIODE MTZJT-774.3A
QDTA0MTZJ4R3
C609
CERAMIC CAP. 680pF/2KV
CA3D681PAN04
D132
ZENER DIODE MTZJT-776.2B
QDTB0MTZJ6R2
C610#
ELECTROLYTIC CAPACITOR 270µF/200V
CA2D271DYG05
D171
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
C611
FILM CAP.(P) 0.056µF/50V J
CMA1JJS00563
D320
ZENER DIODE MTZJT-7712B
QDTB00MTZJ12
C614
FILM CAP.(P) 0.0033µF/50V J
CMA1JJS00332
D322
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
C616
FILM CAP.(P) 0.082µF/50V J
CMA1JJS00823
D323
ZENER DIODE MTZJT-779.1B
QDTB0MTZJ9R1
C642#
CAP CERAMIC 4700pF/250V/M/KX
CA2E472MR101
D326
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
C650
CERAMIC CAP. 560pF/2KV
CA3D561PAN04
D351
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
C652
CERAMIC CAP. B K 1500pF/500V
CCD2JKS0B152
D352
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
C653
ELECTROLYTIC CAP. 2200µF/6.3V M
CE0KMASDL222
D353
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
C654
ELECTROLYTIC CAP. 0.47µF/50V M
CE1JMASDLR47
D501
SCHOTTKY BARRIER DIODE SB140
NDWZ000SB140
C655
ELECTROLYTIC CAP. 0.22µF/50V M
CE1JMASDLR22
D502#
ZENER DIODE MTZJT-7722A
QDTA00MTZJ22
C656
ELECTROLYTIC CAP. 100µF/160V M
CE2CMZNDL101
D503#
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
QDTB00MTZJ10
C657
ELECTROLYTIC CAP. 470µF/35V M
CE1GMZADL471
D516
ZENER DIODE MTZJT-7710B
C658
ELECTROLYTIC CAP. 1000µF/10V M
CE1AMASDL102
D571
DIODE FR104-B
NDLZ000FR104
C659
ELECTROLYTIC CAP 3300µF/6.3V M
CE0KMZNDL332
D572
FAST RECOVERY DIODE ERA22-04
QDPZ0ERA2204
C662
ELECTROLYTIC CAP. 1000µF/16V M
CE1CMZPDL102
D583
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
C663
CHIP CERAMIC CAP. B K 1000pF/50V
CHD1JKB0B102
D584#
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
C667
ELECTROLYTIC CAP. 1µF/50V M
CE1JMASDL1R0
D585
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
C674
ELECTROLYTIC CAP. 1µF/50V M
CE1JMASDL1R0
D591#
ZENER DIODE MTZJT-7736B
QDTB00MTZJ36
C681
ELECTROLYTIC CAP. 1µF/50V M
CE1JMASDL1R0
D595#
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
C682
ELECTROLYTIC CAP. 100µF/10V M
CE1AMASDL101
D597
ZENER DIODE MTZJT-776.8B
QDTB0MTZJ6R8
C684
ELECTROLYTIC CAP. 1000µF/10V M
CE1AMASDL102
D605#
DIODE 1N5399-B/P
NDLZ001N5399
C685
ELECTROLYTIC CAP. 100µF/10V M
CE1AMASDL101
D606#
DIODE 1N5399-B/P
NDLZ001N5399
C705
CHIP CERAMIC CAP. B K 4700pF/50V
CHD1JKB0B472
D607#
DIODE 1N5399-B/P
NDLZ001N5399
C706
CHIP CERAMIC CAP. F Z 1µF/16V
CHD1CZB0F105
D608#
DIODE 1N5399-B/P
NDLZ001N5399
C708
CHIP CERAMIC CAP. B K 4700pF/50V
CHD1JKB0B472
D611#
ZENER DIODE MTZJT-7724C
QDTC00MTZJ24
C709
CHIP CERAMIC CAP. F Z 1µF/16V
CHD1CZB0F105
D612#
ZENER DIODE MTZJT-7739B
QDTB00MTZJ39
C725
CHIP CERAMIC CAP. B K 4700pF/50V
CHD1JKB0B472
D613
ZENER DIODE MTZJT-775.6B
QDTB0MTZJ5R6
C726
CHIP CERAMIC CAP. F Z 1µF/16V
CHD1CZB0F105
D614
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
C728
CHIP CERAMIC CAP. B K 4700pF/50V
CHD1JKB0B472
D615#
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
C729
CHIP CERAMIC CAP. F Z 1µF/16V
CHD1CZB0F105
D623
PCB JUMPER D0.6-P5.0
JW5.0T
C773
ELECTROLYTIC CAP. 100µF/10V M
CE1AMASDL101
D650
DIODE FR154
NDLZ000FR154
C801
ELECTROLYTIC CAP. 220µF/16V M
CE1CMASDL221
D651A
DIODE FAST RECOVERY ERD29-06
QDLZ0ERD2906
C802
ELECTROLYTIC CAP. 220µF/16V M
CE1CMASDL221
D652
DIODE FR154
NDLZ000FR154
C807
ELECTROLYTIC CAP. 4.7µF/50V M
CE1JMASDL4R7
D653
DIODE FR154
NDLZ000FR154
C808
ELECTROLYTIC CAP. 1µF/50V M
CE1JMASDL1R0
D654
DIODE FR104-B
NDLZ000FR104
C809
ELECTROLYTIC CAP. 1µF/50V M
CE1JMASDL1R0
D656#
ZENER DIODE MTZJT-777.5B
QDTB0MTZJ7R5
NDLZ000FR154
C811
ELECTROLYTIC CAP. 470µF/16V M
CE1CMASDL471
D657
DIODE FR154
C833
ELECTROLYTIC CAP. 47µF/16V M
CE1CMASDL470
D658#
DIODE ZENER 1ZC15(Q)
QDLZ001ZC15Q
C851
CHIP CERAMIC CAP. F Z 1µF/10V
CHD1AZB0F105
D659
SCHOTTKY BARRIER DIODE SB340
NDQZ000SB340
C852
CHIP CERAMIC CAP. F Z 1µF/10V
CHD1AZB0F105
D660
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
C853
CHIP CERAMIC CAP. B K 3300pF/50V
CHD1JKB0B332
D661#
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
C854
CHIP CERAMIC CAP. B K 3300pF/50V
CHD1JKB0B332
D662
ZENER DIODE MTZJT-7711A
QDTA00MTZJ11
QDTB00MTZJ33
C904
ELECTROLYTIC CAP. 100µF/6.3V M
CE0KMASDL101
D666
ZENER DIODE MTZJT-7733B
C905
ELECTROLYTIC CAP. 100µF/6.3V M
CE0KMASDL101
D671
PCB JUMPER D0.6-P5.0
JW5.0T
C906
ELECTROLYTIC CAP. 100µF/6.3V M
CE0KMASDL101
D672
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
C907
ELECTROLYTIC CAP. 1000µF/6.3V M
CE0KMASDL102
D680
DIODE 1ZC36(Q)
QDLZ001ZC36Q
C910
ELECTROLYTIC CAP. 47µF/16V M
CE1CMASDL470
D685#
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
C932
CHIP CERAMIC CAP. F Z 1µF/10V
CHD1AZB0F105
D686
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
C935
CHIP CERAMIC CAP. CH J 68pF/50V
CHD1JJBCH680
D841
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
C936
CHIP CERAMIC CAP. CH J 68pF/50V
CHD1JJBCH680
D842
ZENER DIODE MTZJT-775.1B
QDTB0MTZJ5R1
D904
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
CN571
CONNECTOR PRINT OSU 5P RTB-1.5-5P (LF) J3RTC05JG002
D905
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
CN691A
TERMINAL PRINTBORD PIN MS-PIN155155
JTEA001CHY01
D906
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
CN691B
TERMINAL PRINTBORD PIN MS-PIN155155
JTEA001CHY01
D907
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
CN801
CONNECTOR PRINT OSU
008283021200000S+
J383C02UG004
D909
ZENER DIODE MTZJT-775.6C
QDTC0MTZJ5R6
D910
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
CONNECTOR PRINT OSU
008283021200000S+
J383C02UG004
IC31
IC VIF/SIF M61113FP TF0G
QSZBA0SHT035
IC111
IC MICRO COMPUTER R2J10180GF-A13FP
80P
QSZAA0RHT146
IC551
VERTICAL OUTPUT IC LA78040A
QSBBA0SSY003
CONNECTORS
CN802
ICS
DIODES
D101
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
D102
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
20070111
14-2
P7151EL
Ref. No.
Description
Part No.
Ref. No.
Description
Part No.
IC601#
PHOTOCOUPLER LTV-817C-F
NPEC0LTV817F
R45
CHIP RES. 1/10W J 220 Ω
RRXAJB5Z0221
IC701
IC SWITCHING TC4052BF(ELNF)
QSZBA0TTS162
R46
CHIP RES. 1/10W J 1.8k Ω
RRXAJB5Z0182
IC801
IC AN17812A
QSZBA0SMS017
R70
CHIP RES.(1608) 1/10W 0 Ω
RRXAZB5Z0000
IC901
IC EEPROM AT24C128N-10SU-1.8 S
NSZBA0TAZ083
R71
CHIP RES.(1608) 1/10W 0 Ω
RRXAZB5Z0000
IC903
VOLTAGE REGULATOR PQ070XF01SZH
QSZBA0SSH054
R101
CARBON RES. 1/4W J 100 Ω
RCX4JATZ0101
IC905
IC SHUNT REGULATOR KIA431-AT/P
NSZBA0TJY036
R102
CHIP RES. 1/10W J 2.2k Ω
RRXAJB5Z0222
IC911
IC SHUNT REGULATOR KIA431-AT/P
NSZBA0TJY036
R103
CHIP RES. 1/10W J 2.7k Ω
RRXAJB5Z0272
R104
CHIP RES. 1/10W J 4.7k Ω
RRXAJB5Z0472
COILS
L12
PCB JUMPER D0.6-P5.0
JW5.0T
R105
CHIP RES. 1/10W J 6.8k Ω
RRXAJB5Z0682
L32
INDUCTOR 18µH-J-26T
LLAXJATTU180
R106
CHIP RES. 1/10W J 1.2k Ω
RRXAJB5Z0122
L51
PCB JUMPER D0.6-P5.0
JW5.0T
R107
CHIP RES. 1/10W J 68k Ω
RRXAJB5Z0683
L72
PCB JUMPER D0.6-P5.0
JW5.0T
R108
CHIP RES. 1/10W J 10k Ω
RRXAJB5Z0103
L74
PCB JUMPER D0.6-P5.0
JW5.0T
R109
CHIP RES. 1/10W J 2.2k Ω
RRXAJB5Z0222
L112
PCB JUMPER D0.6-P5.0
JW5.0T
R111
CARBON RES. 1/4W J 100 Ω
RCX4JATZ0101
L301
PCB JUMPER D0.6-P5.0
JW5.0T
R112
CARBON RES. 1/4W J 10k Ω
RCX4JATZ0103
L588
CHOKE COIL 22µH-K
LLBD00PKV021
R113
CHIP RES. 1/10W J 270k Ω
RRXAJB5Z0274
L601#
LINE FILTER ELF15N813AN
LLBG00ZMS050
R114
CHIP RES. 1/10W J 1k Ω
RRXAJB5Z0102
L901
COIL DRUM A60607188/47µH
LLED0P0KV001
R115
CARBON RES. 1/4W J 270 Ω
RCX4JATZ0271
R119
CHIP RES.(1608) 1/10W 0 Ω
RRXAZB5Z0000
TRANSISTORS
Q31
NPN TRANSISTOR KRC103M-AT/P
NQSZKRC103MP
R120
CHIP RES.(1608) 1/10W 0 Ω
RRXAZB5Z0000
Q111#
TRANSISTOR KTC3199-GR-AT/P
NQS4KTC3199P
R121
CHIP RES.(1608) 1/10W 0 Ω
RRXAZB5Z0000
CHIP RES.(1608) 1/10W 0 Ω
RRXAZB5Z0000
Q112
TRANSISTOR KTC3199-GR-AT/P
NQS4KTC3199P
R122
Q113
TRANSISTOR KTC3199-GR-AT/P
NQS4KTC3199P
R130
CARBON RES. 1/4W J 22k Ω
RCX4JATZ0223
Q131
NPN TRANSISTOR KRC103M-AT/P
NQSZKRC103MP
R131
CHIP RES. 1/10W J 470 Ω
RRXAJB5Z0471
Q161
NPN TRANSISTOR KRC103M-AT/P
NQSZKRC103MP
R132
CHIP RES. 1/10W J 4.7k Ω
RRXAJB5Z0472
CHIP RES.(1608) 1/10W 0 Ω
RRXAZB5Z0000
Q321
TRANSISTOR KTC3199-GR-AT/P
NQS4KTC3199P
R133
Q322
TRANSISTOR KTC3199-GR-AT/P
NQS4KTC3199P
R134
CHIP RES. 1/10W J 4.7k Ω
RRXAJB5Z0472
Q361
TRANSISTOR KTC3199-GR-AT/P
NQS4KTC3199P
R135
CHIP RES. 1/10W J 4.7k Ω
RRXAJB5Z0472
Q571#
NPN TRANSISTOR 2SC6093LS-YB11
QQEZ02SC6093
R136
CHIP RES. 1/10W J 100k Ω
RRXAJB5Z0104
CHIP RES. 1/10W J 100 Ω
RRXAJB5Z0101
Q572
NPN TRANSISTOR 2SC1627-Y (TE2.F.T)
QQSY2SC1627F
R137
Q601#
MOS FET 2SK3563
QFWZ02SK3563
R138
CHIP RES. 1/10W J 220k Ω
RRXAJB5Z0224
Q602#
TRANSISTOR 2SC2120-O(TE2 F T)
QQS02SC2120F
R139
CHIP RES. 1/10W J 22k Ω
RRXAJB5Z0223
Q652#
TRANSISTOR KTC3199-GR-AT/P
NQS4KTC3199P
R140
CHIP RES. 1/10W J 1k Ω
RRXAJB5Z0102
CHIP RES.(1608) 1/10W 0 Ω
RRXAZB5Z0000
Q672#
TRANSISTOR KTA-1266-GR-AT/P
NQS4KTA1266P
R141
Q673
TRANSISTOR KTC3199-GR-AT/P
NQS4KTC3199P
R150
CHIP RES.(1608) 1/10W 0 Ω
RRXAZB5Z0000
Q674
TRANSISTOR KTC3199-GR-AT/P
NQS4KTC3199P
R161
CHIP RES.(1608) 1/10W 0 Ω
RRXAZB5Z0000
Q681#
TRANSISTOR KTC3199-GR-AT/P
NQS4KTC3199P
R162
CHIP RES. 1/10W J 10k Ω
RRXAJB5Z0103
CHIP RES.(1608) 1/10W 0 Ω
RRXAZB5Z0000
Q682#
TRANSISTOR KTC3199-GR-AT/P
NQS4KTC3199P
R163
Q811
TRANSISTOR KTC3199-GR-AT/P
NQS4KTC3199P
R164
CARBON RES. 1/4W J 10k Ω
RCX4JATZ0103
Q901
TRANSISTOR 2SA950-O (TE2 F T)
QQS002SA950F
R165
CHIP RES. 1/10W J 4.7k Ω
RRXAJB5Z0472
Q902
TRANSISTOR KTC3199-GR-AT/P
NQS4KTC3199P
R167
CHIP RES. 1/10W J 2.7k Ω
RRXAJB5Z0272
CHIP RES. 1/10W J 4.7k Ω
RRXAJB5Z0472
Q903
TRANSISTOR 2SC2120-O(TE2 F T)
QQS02SC2120F
R168
Q904
TRANSISTOR 2SC2120-O(TE2 F T)
QQS02SC2120F
R170
CHIP RES. 1/10W J 6.8k Ω
RRXAJB5Z0682
Q910
TRANSISTOR 2SC2120-O(TE2 F T)
QQS02SC2120F
R171
CARBON RES. 1/4W J 560 Ω
RCX4JATZ0561
Q911
TRANSISTOR KTC3199-GR-AT/P
NQS4KTC3199P
R172
CHIP RES.(1608) 1/10W 0 Ω
RRXAZB5Z0000
NQS4KTC3199P
R173
CARBON RES. 1/4W J 22k Ω
RCX4JATZ0223
Q912
TRANSISTOR KTC3199-GR-AT/P
R174
CHIP RES. 1/10W J 4.7k Ω
RRXAJB5Z0472
R11
CHIP RES.(1608) 1/10W 0 Ω
RRXAZB5Z0000
R178
CHIP RES. 1/10W J 470 Ω
RRXAJB5Z0471
R12
CHIP RES.(1608) 1/10W 0 Ω
RRXAZB5Z0000
R301
CHIP RES. 1/10W J 10k Ω
RRXAJB5Z0103
RRXAJB5Z0221
R302
CARBON RES. 1/4W J 10 Ω
RCX4JATZ0100
CHIP RES. 1/10W J 470 Ω
RRXAJB5Z0471
RESISTORS
R24
CHIP RES. 1/10W J 220 Ω
R25
CHIP RES. 1/10W J 220 Ω
RRXAJB5Z0221
R303
R31
CHIP RES. 1/10W J 2.2k Ω
RRXAJB5Z0222
R304
CHIP RES. 1/10W J 4.7M Ω
RRXAJB5Z0475
R32
CARBON RES. 1/4W J 390 Ω
RCX4JATZ0391
R305
CHIP RES. 1/10W J 470 Ω
RRXAJB5Z0471
RRXAJB5Z0271
R306
CARBON RES. 1/4W J 15 Ω
RCX4JATZ0150
CARBON RES. 1/4W J 10 Ω
RCX4JATZ0100
R33
CHIP RES. 1/10W J 270 Ω
R35
CARBON RES. 1/4W J 27k Ω
RCX4JATZ0273
R307
R36
CHIP RES. 1/10W J 47 Ω
RRXAJB5Z0470
R308
CARBON RES. 1/4W J 75 Ω
RCX4JATZ0750
R37
CHIP RES. 1/10W J 220 Ω
RRXAJB5Z0221
R323
CARBON RES. 1/4W J 5.6k Ω
RCX4JATZ0562
R38
CARBON RES. 1/4W J 12k Ω
RCX4JATZ0123
R324
CARBON RES. 1/4W J 5.6k Ω
RCX4JATZ0562
CHIP RES. 1/10W J 100 Ω
RRXAJB5Z0101
R39
CHIP RES. 1/10W J 27k Ω
RRXAJB5Z0273
R326
R41
CHIP RES. 1/10W J 3.3k Ω
RRXAJB5Z0332
R327
CHIP RES.(1608) 1/10W 0 Ω
RRXAZB5Z0000
R43
CHIP RES. 1/10W J 12k Ω
RRXAJB5Z0123
R328
CHIP RES. 1/10W J 47k Ω
RRXAJB5Z0473
RRXAJB5Z0152
R329
CHIP RES. 1/10W J 47k Ω
RRXAJB5Z0473
R330
CHIP RES. 1/10W J 1k Ω
RRXAJB5Z0102
R44
CHIP RES. 1/10W J 1.5k Ω
20070111
14-3
P7151EL
Ref. No.
Description
Part No.
Ref. No.
Description
Part No.
CARBON RES. 1/4W J 22 Ω
RCX4JATZ0220
R618
CARBON RES. 1/4W J 180 Ω
RCX4JATZ0181
R333
CHIP RES. 1/10W J 22 Ω
RRXAJB5Z0220
R621
CARBON RES. 1/4W J 1k Ω
RCX4JATZ0102
R342
CHIP RES.(1608) 1/10W 0 Ω
RRXAZB5Z0000
R635
CARBON RES. 1/4W J 180 Ω
RCX4JATZ0181
R344
CHIP RES. 1/10W J 6.8k Ω
RRXAJB5Z0682
R641
METAL OXIDE FILM RES. 1W J 5.6k Ω
RN01562ZU001
R345
CHIP RES. 1/10W J 10k Ω
RRXAJB5Z0103
R651
METAL OXIDE FILM RES. 1W J 5.6k Ω
RN01562ZU001
R331
R346
CHIP RES. 1/10W J 1k Ω
RRXAJB5Z0102
R656
CHIP RES. 1/10W J 15k Ω
RRXAJB5Z0153
R348
CARBON RES. 1/4W J 27k Ω
RCX4JATZ0273
R657
CHIP RES. 1/10W J 15k Ω
RRXAJB5Z0153
R349
CHIP RES. 1/10W J 3.3k Ω
RRXAJB5Z0332
R659
CHIP RES. 1/10W J 10k Ω
RRXAJB5Z0103
R350
CHIP RES. 1/10W J 2.2k Ω
RRXAJB5Z0222
R661#
CARBON RES. 1/4W J 39k Ω
RCX4JATZ0393
R351
CHIP RES. 1/10W J 2.2k Ω
RRXAJB5Z0222
R662#
CARBON RES. 1/4W J 1.8k Ω
RCX4JATZ0182
R352
CARBON RES. 1/4W J 2.2k Ω
RCX4JATZ0222
R663#
CARBON RES. 1/4W J 8.2k Ω
RCX4JATZ0822
R355
CHIP RES. 1/10W J 33k Ω
RRXAJB5Z0333
R664#
CARBON RES. 1/4W J 1.2k Ω
RCX4JATZ0122
R356
CHIP RES. 1/10W J 100 Ω
RRXAJB5Z0101
R665#
CARBON RES. 1/4W J 5.6k Ω
RCX4JATZ0562
R357
CHIP RES. 1/10W J 100 Ω
RRXAJB5Z0101
R667#
CARBON RES. 1/4W J 8.2k Ω
RCX4JATZ0822
R358
CHIP RES. 1/10W J 100 Ω
RRXAJB5Z0101
R668#
CARBON RES. 1/4W J 8.2k Ω
RCX4JATZ0822
R361
CHIP RES. 1/10W J 10k Ω
RRXAJB5Z0103
R669#
PCB JUMPER D0.6-P5.0
JW5.0T
R362
CARBON RES. 1/4W J 100 Ω
RCX4JATZ0101
R670#
CARBON RES. 1/4W J 47k Ω
RCX4JATZ0473
R363
CHIP RES. 1/10W J 47k Ω
RRXAJB5Z0473
R673
CARBON RES. 1/4W J 100k Ω
RCX4JATZ0104
R503
CARBON RES. 1/4W J 56k Ω
RCX4JATZ0563
R674
CHIP RES. 1/10W J 22k Ω
RRXAJB5Z0223
R504
CARBON RES. 1/4W J 4.7 Ω
RCX4JATZ04R7
R675#
CARBON RES. 1/4W J 10k Ω
RCX4JATZ0103
R505
CARBON RES. 1/4W J 1.5k Ω
RCX4JATZ0152
R676
CARBON RES. 1/4W J 10k Ω
RCX4JATZ0103
RCX4JATZ0153
R506
CARBON RES. 1/4W J 3.3 Ω
RCX4JATZ03R3
R677
CARBON RES. 1/4W J 15k Ω
R507
CARBON RES. 1/4W J 3.3 Ω
RCX4JATZ03R3
R678
CHIP RES. 1/10W J 47k Ω
RRXAJB5Z0473
R514
CARBON RES. 1/4W J 4.7k Ω
RCX4JATZ0472
R680
CARBON RES. 1/4W J 10k Ω
RCX4JATZ0103
R515#
METAL OXIDE FILM RES. 2W J 12 Ω
RN02120ZU001
R681
CARBON RES. 1/4W J 6.8 Ω
RCX4JATZ06R8
R519#
CARBON RES. 1/4W J 3.3 Ω
RCX4JATZ03R3
R684#
CARBON RES. 1/4W J 4.7 Ω
RCX4JATZ04R7
R520#
CHIP RES. 1/10W J 3.3k Ω
RRXAJB5Z0332
R685#
PCB JUMPER D0.6-P5.0
JW5.0T
R522
CARBON RES. 1/4W J 22k Ω
RCX4JATZ0223
R686
CARBON RES. 1/4W J 10 Ω
RCX4JATZ0100
R541
CARBON RES. 1/4W J 820 Ω
RCX4JATZ0821
R687#
CARBON RES. 1/4W J 10 Ω
RCX4JATZ0100
R542
CARBON RES. 1/4W J 820 Ω
RCX4JATZ0821
R689
CARBON RES. 1/4W J 8.2 Ω
RCX4JATZ08R2
R544
CARBON RES. 1/4W J 1.5k Ω
RCX4JATZ0152
R694
CHIP RES.(1608) 1/10W 0 Ω
RRXAZB5Z0000
R570
CARBON RES. 1/4W J 47 Ω
RCX4JATZ0470
R705
CHIP RES. 1/10W J 15k Ω
RRXAJB5Z0153
R571
METAL OXIDE FILM RES. 2W J 1k Ω
RN02102ZU001
R706
CHIP RES. 1/10W J 6.8k Ω
RRXAJB5Z0682
R572
METAL OXIDE FILM RES. 2W J 1k Ω
RN02102ZU001
R708
CHIP RES. 1/10W J 15k Ω
RRXAJB5Z0153
R574
CARBON RES. 1/4W J 180 Ω
RCX4JATZ0181
R709
CHIP RES. 1/10W J 6.8k Ω
RRXAJB5Z0682
R575#
CARBON RES. 1/4W J 47 Ω
RCX4JATZ0470
R711
CHIP RES. 1/10W J 75 Ω
RRXAJB5Z0750
R576
CHIP RES. 1/10W J 1k Ω
RRXAJB5Z0102
R716
CHIP RES. 1/10W J 75 Ω
RRXAJB5Z0750
R577
CARBON RES. 1/4W J 220 Ω
RCX4JATZ0221
R721
CHIP RES. 1/10W J 75 Ω
RRXAJB5Z0750
R578#
CARBON RES. 1/4W J 47 Ω
RCX4JATZ0470
R725
CHIP RES. 1/10W J 15k Ω
RRXAJB5Z0153
R579#
CARBON RES. 1/4W J 47 Ω
RCX4JATZ0470
R726
CHIP RES. 1/10W J 6.8k Ω
RRXAJB5Z0682
R581
PCB JUMPER D0.6-P5.0
JW5.0T
R728
CHIP RES. 1/10W J 15k Ω
RRXAJB5Z0153
R583#
METAL OXIDE FILM RES. 2W J 2.7 Ω
RN02JZLZ02R7
R729
CHIP RES. 1/10W J 6.8k Ω
RRXAJB5Z0682
R584#
CARBON RES. 1/4W J 1k Ω
RCX4JATZ0102
R751
CARBON RES. 1/4W J 22k Ω
RCX4JATZ0223
RRXAJB5Z0273
R588#
CARBON RES. 1/4W J 100k Ω
RCX4JATZ0104
R752
CHIP RES. 1/10W J 27k Ω
R589
CARBON RES. 1/4W J 100k Ω
RCX4JATZ0104
R761
CARBON RES. 1/4W J 22k Ω
RCX4JATZ0223
R590
CARBON RES. 1/4W J 270k Ω
RCX4JATZ0274
R762
CHIP RES. 1/10W J 27k Ω
RRXAJB5Z0273
R591#
CARBON RES. 1/4W G 220k Ω
RCX4GATZ0224
R771
CARBON RES. 1/4W J 10k Ω
RCX4JATZ0103
R592#
CARBON RES. 1/4W G 150k Ω
RCX4GATZ0154
R772
CARBON RES. 1/4W J 10k Ω
RCX4JATZ0103
R593#
CARBON RES. 1/4W G 82k Ω
RCX4GATZ0823
R801
CARBON RES. 1/4W J 100 Ω
RCX4JATZ0101
R594#
CARBON RES. 1/4W J 100k Ω
RCX4JATZ0104
R802
CARBON RES. 1/4W J 100 Ω
RCX4JATZ0101
R597
CARBON RES. 1/4W J 8.2k Ω
RCX4JATZ0822
R811
CHIP RES. 1/10W J 10k Ω
RRXAJB5Z0103
R598#
CARBON RES. 1/4W J 47k Ω
RCX4JATZ0473
R812
CHIP RES. 1/10W J 27k Ω
RRXAJB5Z0273
R599#
CARBON RES. 1/4W J 22k Ω
RCX4JATZ0223
R813
CHIP RES. 1/10W J 8.2k Ω
RRXAJB5Z0822
R601#
CEMENT RES 5W K 1.2 Ω
RW051R2PG002
R814
CARBON RES. 1/4W J 4.7k Ω
RCX4JATZ0472
JW5.0T
R602#
CARBON RES. 1/4W J 820k Ω
RCX4JATZ0824
R842
PCB JUMPER D0.6-P5.0
R603
CARBON RES. 1/4W J 820k Ω
RCX4JATZ0824
R843#
CHIP RES. 1/10W J 2.2k Ω
RRXAJB5Z0222
R604
CARBON RES. 1/4W J 390k Ω
RCX4JATZ0394
R844
METAL OXIDE FILM RES. 2W J 2.2 Ω
RN022R2ZU001
RRXAJB5Z0472
R605
PCB JUMPER D0.6-P5.0
JW5.0T
R851
CHIP RES. 1/10W J 4.7k Ω
R606
CARBON RES. 1/4W J 180k Ω
RCX4JATZ0184
R852
CHIP RES. 1/10W J 2.2k Ω
RRXAJB5Z0222
R607
CARBON RES. 1/4W J 330 Ω
RCX4JATZ0331
R853
CARBON RES. 1/4W J 4.7k Ω
RCX4JATZ0472
R608
CARBON RES. 1/4W J 270 Ω
RCX4JATZ0271
R854
CHIP RES. 1/10W J 2.2k Ω
RRXAJB5Z0222
R613#
METAL OXIDE FILM RES. 2W J 0.33 Ω
RN02R33ZU001
R862
CHIP RES.(1608) 1/10W 0 Ω
RRXAZB5Z0000
R616
CARBON RES. 1/4W J 1.5k Ω
RCX4JATZ0152
R863
CHIP RES. 1/10W J 10k Ω
RRXAJB5Z0103
20070111
14-4
P7151EL
Ref. No.
Description
R901
CARBON RES. 1/4W J 56k Ω
R902
R903
R904
Ref. No.
Part No.
Description
Part No.
RCX4JATZ0563
GP641#
GAP. FNR-G3.10D
FAZ000LD6005
CARBON RES. 1/4W J 1k Ω
RCX4JATZ0102
JK701
RCA JACK(YELLOW) MTJ-032-05B-20(B110)
JXRL010LY135
CHIP RES. 1/10W J 4.7k Ω
RRXAJB5Z0472
JK702
RCA JACK(WHITE) MTJ-032-05B-22(B110)
JXRL010LY136
PCB JUMPER D0.6-P5.0
JW5.0T
JK703
RCA JACK(RED) MTJ-032-05A-21(B110)
JYRL010LY029
R905
CARBON RES. 1/4W J 1.5 Ω
RCX4JATZ01R5
JK721
JACK SW DIN PCB L DIN-435C
JYEL040YUQ02
R907
CARBON RES. 1/4W J 1.2 Ω
RCX4JATZ01R2
JK742
JACK SW RCA PCB L RCA-350-00A-01
JYRL030YUQ11
R911
CARBON RES. 1/4W J 820 Ω
RCX4JATZ0821
JK743
R912
CHIP RES. 1/10W J 3.3k Ω
RRXAJB5Z0332
JACK RCA PCB ORENGE MTJ-032-05B-52 FE JXRL010LY159
LF
R913
CHIP RES. 1/10W J 10k Ω
RRXAJB5Z0103
JK801
MINIATURE JACK(PB FREE) CKX-035-318AZ4 JYSL010SNJ01
JS575
PCB JUMPER D0.6-P10.0
JW10.0T
JS581
PCB JUMPER D0.6-P5.0
JW5.0T
JS601
PCB JUMPER D0.6-P7.5
JW7.5T
JS805
PCB JUMPER D0.6-P7.5
JW7.5T
PS691#
THERMISTOR ZPB45BL3R0A
QNBZ45BL3R0A
RCV101
REMOCON RECEIVE UNIT KSM-602SR2E-2
USESJRSKK045
SA601#
SURGE ABSORBER 470V+-10PER
NVQZ10D471KB
SF11
FILTER CERAMIC BAND PASS
SAFHS45M7VAMZ00B05
FBB456LMR005
LTH00CPA5005
R914
CARBON RES. 1/4W J 1k Ω
RCX4JATZ0102
R915
CARBON RES. 1/4W J 2.7 Ω
RCX4JATZ02R7
R916
CHIP RES. 1/10W F 10k Ω
RRXAFB5H1002
R917
CHIP RES.(1608) 1/10W 0 Ω
RRXAZB5Z0000
R918
R919
CHIP RES.(1608) 1/10W 0 Ω
CHIP RES. 1/10W J 22k Ω
RRXAZB5Z0000
RRXAJB5Z0223
R920
CHIP RES.(1608) 1/10W 0 Ω
RRXAZB5Z0000
R921
CHIP RES.(1608) 1/10W 0 Ω
RRXAZB5Z0000
R922
CARBON RES. 1/4W J 390 Ω
RCX4JATZ0391
CHIP RES. 1/10W J 680 Ω
T572#
HORIZONTAL DRIVE TRANS LP2-005
R923
RRXAJB5Z0681
TRANS POWER 6752
LTT2PC0KT016
R924
CHIP RES.(1608) 1/10W 0 Ω
T601#
RRXAZB5Z0000
MODULE HEAT SINK PMC P7150UT
1EM423968
R925
CARBON RES. 1/4W J 220 Ω
TB9
RCX4JATZ0221
CHIP RES. 1/10W F 4.7k Ω
TB10
H/V HEAT SINK PMB ASSEMBLY P7150UT
1EM423967
R927
RRXAFB5H4701
POW HEAT SINK PMA P7150UT
1EM423965
R928
CHIP RES. 1/10W F 150 Ω
TB11
RRXAFB5H1500
CHIP RES. 1/10W F 220 Ω
TL2
SCREW B-TIGHT D3X8 BIND HEAD+
GBJB3080
R929
RRXAFB5H2200
TP601
PCB JUMPER D0.6-P14.0
JW14.0T
R930
CHIP RES. 1/10W F 22k Ω
RRXAFB5H2202
CARBON RES. 1/4W J 1.2 Ω
TU11
TUNER UNIT ENV56M07D8F
UTUNATSMS001
R931
RCX4JATZ01R2
VR661#
CARBON P.O.T. VZ067TL1 B103 PB(F)
VRCB103HH014
X301
XTAL 3.579545 MHz
FXD355LLN003
R932
CARBON RES. 1/4W J 2.2 Ω
RCX4JATZ02R2
R934
CARBON RES. 1/4W J 560 Ω
RCX4JATZ0561
R935
CHIP RES. 1/10W J 56k Ω
RRXAJB5Z0563
R936
CHIP RES. 1/10W J 22k Ω
RRXAJB5Z0223
R937
CARBON RES. 1/4W J 56k Ω
RCX4JATZ0563
R938
CHIP RES. 1/10W J 22k Ω
RRXAJB5Z0223
R940
METAL OXIDE FILM RES. 2W J 0.39 Ω
RN02R39ZU001
R942
CHIP RES. 1/10W J 10k Ω
RRXAJB5Z0103
R943
R945
CHIP RES. 1/10W J 10k Ω
PCB JUMPER D0.6-P5.0
CRT CBA
Ref. No.
SW102
TACT SWITCH SKQSAB
TACT SWITCH SKQSAB
CAPACITORS
RRXAJB5Z0103
ELECTROLYTIC CAP. 47µF/16V M
CE1CMASDL470
JW5.0T
C1510
CERAMIC CAP. B K 1000pF/2KV
CCD3DKD0B102
C1511
CERAMIC CAP.(AX) B K 330pF/50V
CCA1JKT0B331
C1521
CERAMIC CAP.(AX) B K 270pF/50V
CCA1JKT0B271
C1531
CERAMIC CAP.(AX) B K 330pF/50V
CCA1JKT0B331
SST0101AL038
SST0101AL038
SW103
TACT SWITCH SKQSAB
SST0101AL038
SW104
TACT SWITCH SKQSAB
SST0101AL038
SW105
TACT SWITCH SKQSAB
SST0101AL038
SW106
TACT SWITCH SKQSAB
SST0101AL038
CONNECTOR
CN1501
AC CORD (PB FREE) A0A0280-012
CONNECTOR PIN 1P RT-01N-2.3A
1730688
DIODES
MISCELLANEOUS
AC601#
Part No.
---------
C1502
SWITCHES
SW101
Description
CRT CBA
Consists of the following:
WAC0172LTE12
D1511
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
D1521
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
D1531
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
COIL
BC14
BEAD INDUCTOR FBR07HA121TB-00
BC15
BEAD INDUCTOR FBR07HA121TB-00
LLBF00ZTU021
LLBF00ZTU021
BC571
BEAD INDUCTOR FBA04HA600VB-00
LLBF00STU026
BC572
PCB JUMPER D0.6-P5.0
JW5.0T
Q1511
NPN TRANSISTOR 2SC2482(T6FUNAIF M
QRSZ2SC2482F
BC603
BEAD INDUCTOR FBR07HA121TB-00
LLBF00ZTU021
Q1521
NPN TRANSISTOR 2SC2482(T6FUNAIF M
QRSZ2SC2482F
BC652
BEAD INDUCTOR FBR07HA121TB-00
LLBF00ZTU021
Q1531
NPN TRANSISTOR 2SC2482(T6FUNAIF M
QRSZ2SC2482F
BC653
PCB JUMPER D0.6-P5.0
JW5.0T
BC655
BEAD INDUCTOR FBR07HA121TB-00
LLBF00ZTU021
R1501
PCB JUMPER D0.6-P5.0
JW5.0T
BC657
BEAD INDUCTOR FBR07HA121TB-00
LLBF00ZTU021
R1502
PCB JUMPER D0.6-P5.0
JW5.0T
BC691
BEAD INDUCTOR FBR07HA121TB-00
LLBF00ZTU021
R1503
PCB JUMPER D0.6-P5.0
JW5.0T
CF31
CERAMIC TRAP 4.5MHz
FBE455PMR003
R1510#
METAL OXIDE FILM RES. 1W J 15k Ω
RN01153ZU001
CF32
CERAMIC FILTER SFSRA4M50CF00-B0
FBB455PMR004
R1511
CARBON RES. 1/4W J 1.5k Ω
RCX4JATZ0152
CLN301
WIRE ASSEMBLY L=410 5P
WX1L1040-101
R1513
CARBON RES. 1/4W J 1.5k Ω
RCX4JATZ0152
L1501
INDUCTOR 150µH-J-5FT
LLARJCSTU151
TRANSISTORS
RESISTORS
CLN501
PARALLEL WIRE 3P
WX1L1114-101
R1515
CARBON RES. 1/4W J 5.6k Ω
RCX4JATZ0562
F601#
FUSE 4.00A/125V
PAGG20CNG402
R1518
CARBON RES. 1/4W J 560 Ω
RCX4JATZ0561
FH601
FUSE HOLDER MSF-015 LF (B110)
XH01Z00LY002
R1519
CARBON RES. 1/4W J 33 Ω
RCX4JATZ0330
FH602
FUSE HOLDER MSF-015 LF (B110)
XH01Z00LY002
R1520#
METAL OXIDE FILM RES. 1W J 15k Ω
RN01153ZU001
20070111
14-5
P7151EL
Ref. No.
Description
Part No.
R1521
CARBON RES. 1/4W J 1.5k Ω
RCX4JATZ0152
R1523
CARBON RES. 1/4W J 1.5k Ω
RCX4JATZ0152
R1525
CARBON RES. 1/4W J 5.6k Ω
RCX4JATZ0562
R1528
CARBON RES. 1/4W J 560 Ω
RCX4JATZ0561
R1529
CARBON RES. 1/4W J 33 Ω
RCX4JATZ0330
R1530#
METAL OXIDE FILM RES. 1W J 15k Ω
RN01153ZU001
R1531
CARBON RES. 1/4W J 1.5k Ω
RCX4JATZ0152
R1532
CARBON RES. 1/4W J 1.5k Ω
RCX4JATZ0152
R1535
CARBON RES. 1/4W J 5.6k Ω
RCX4JATZ0562
R1538
CARBON RES. 1/4W J 560 Ω
RCX4JATZ0561
R1539
CARBON RES. 1/4W J 33 Ω
RCX4JATZ0330
MISCELLANEOUS
BC1502
BEAD INDUCTOR FBR07HA121TB-00
JK1501# CRT SOCKET ISMP02S
20070111
LLBF00ZTU021
JSCC220PK009
14-6
P7151EL
© 2007 Funai Electric Co., Ltd.
All rights reserved. No part of this manual may be reproduced, copied, transmitted, disseminated, transcribed,
downloaded or stored in any storage medium, in any form or for any purpose without the express prior written
consent of Funai. Furthermore, any unauthorized commercial distribution of this manual or any revision hereto
is strictly prohibited.
Information in this document is subject to change without notice. Funai reserves the right to change the content
herein without the obligation to notify any person or organization of such changes.
FUNAI with “F” design is a registered trademark of Funai Electric Co., Ltd and may not be used in any way
without the express written consent of Funai. All other trademarks used herein remain the exclusive property of
their respective owners. Nothing contained in this manual should be construed as granting, by implication or
otherwise, any license or right to use any of the trademarks displayed herein. Misuse of any trademarks or any
other content in this manual is strictly prohibited. Funai shall aggressively enforce its intellectual property rights
to the fullest extent of the law.
CR202EM8
P7151UM
2007-01-18