TELUS
i877 Mike Phone
User’s Guide
Dummy Page - To be discarded before printing
DECLARATION OF CONFORMITY
Per FCC CFR 47 Part 2 Section 2.1077(a)
Responsible Party Name: Motorola, Inc.
Address: 8000 West Sunrise Boulevard
Plantation, FL 33322 USA
Phone Number: 1 (800) 453-0920
Hereby declares that the product:
Product Name: i877
Model Number: H92XAH6RR4AN
Conforms to the following regulations:
FCC Part 15, subpart B, section 15.107(a),
15.107(d) and section 15.109(a)
Class B Digital Device
As a personal computer peripheral, this device
complies with Part 15 of the FCC Rules.
Operation is subject to the following two
conditions: (1) this device may not cause
harmful interference, and (2) this device must
accept any interference received, including
interference that may cause undesired
operation.
Note: This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference
will not occur in a particular installation.
If this equipment does cause harmful
interference to radio or television reception,
which can be determined by turning the
equipment off and on, the user is encouraged to
try to correct the interference by one or more of
the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician
for help.
HELLOMOTO
Introducing your new Mike i877 wireless phone. Here’s a quick anatomy lesson.
Left Soft Key
Perform function
in lower left
display.
Menu Key
From home screen,
open main menu.
Right Soft Key
Perform function
in lower right
display.
Speaker
Mini USB Connector
Connects charger
and accessories
Smart Key
Camera Key
End/Power Key
End calls, exit
menu system,
turns phone
on/off.
Talk Key
Make &
answer calls.
4-Way
Navigation Key
Speaker On/Off Key
OK Key
In menus & lists,
press to select
highlighted option.
Camera
Spotlight
Volume
Buttons
Camera
Lens
PTT
Button
Audio Jack
Memory
Card Slot
1
check it out
Home Screen
Main Menu
2
READY
4/25/07
04
05 pm
1
2
Customizable O key
that can be used to
to open the
Settings screen
Press and hold the
Power Key E for a
few seconds, or until
the screen lights up,
to turn on your
phone.
Recent Calls
B
3
Press the Navigation Key
up, down, left or right (
)
to highlight a menu feature.
4
Press the O key
to select.
BLeqjpTmG
More
Exit
Motorola, Inc.
Consumer Advocacy Office
1307 East Algonquin Road
Schaumburg, IL 60196
www.hellomoto.com
1-800-331-6456 (United States)
1-888-390-6456 (TTY/TDD United States for hearing impaired)
1-800-461-4575 (Canada)
Product Support: www.motorola.com/iden
Certain mobile phone features are dependent on the capabilities
and settings of your service provider’s network. Additionally,
certain features may not be activated by your service provider,
and/or the provider's network settings may limit the feature’s
functionality. Always contact your service provider about feature
availability and functionality. All features, functionality, and other
product specifications, as well as the information contained in this
user's guide are based upon the latest available information and
are believed to be accurate at the time of printing. Motorola
reserves the right to change or modify any information or
specifications without notice or obligation.
This device supports Bluetooth 2.0 including EDR and A2DP Stereo
profiles. In order for Bluetooth devices to communicate with one
another, they must utilize the same Bluetooth profile. To determine
the profiles supported by other Motorola devices, visit
www.hellomoto.com/bluetooth. For other devices, contact their
respective manufacturer.
Certain Bluetooth features including those listed may not be
supported by all compatible Bluetooth-enabled devices, and/or the
functionality of such features may be limited in certain devices, or
by certain wireless carriers. Contact your wireless carrier about
feature availability and functionality.
OPEN SOURCE SOFTWARE INFORMATION
You may choose to obtain a copy of any source code being made
publicly available by Motorola directly from the Motorola website
opensource.motorola.com.
Additionally, for instructions on how to obtain a copy of any source
code being made publicly available by Motorola related to
software used in this Motorola mobile device, please send your
request in writing to:
MOTOROLA, INC.
OSS Management
600 North US Hwy 45
Libertyville, IL 60048
USA.
Motorola has created the www.opensource.motorola.com
to serve as a portal for interaction with the software communityat-large.
To see additional information regarding licenses,
acknowledgments and required copyright notices for open source
packages used in this Motorola mobile device, follow these
instructions:
From the phone Main Menu, select Games and Apps. >
OpenSourceNotices.
3
MOTOROLA and the Stylized M Logo are registered in the US
Patent & Trademark Office. All other product or service names are
the property of their respective owners. Java and all other Javabased marks are trademarks or registered trademarks of Sun
Microsystems, Inc. in the U.S. and other countries.
© Motorola, Inc., 2007.
Manual Number: NVN5402A
4
contents
check it out . . . . . . . . . . . 2
menu map. . . . . . . . . . . . 7
Use and Care . . . . . . . . . 9
essentials . . . . . . . . . . . 10
about this guide . . . . . 10
activate your
Mike account . . . . . . . . 11
SIM card . . . . . . . . . . . . 11
memory card . . . . . . . 13
battery . . . . . . . . . . . . 14
turn it on & off . . . . . . 18
make a phone call. . . . 19
answer a phone call . . 19
make a private call . . . 19
answer a private call. . 20
store a phone number
or private ID . . . . . . . . 21
call a stored phone
number or private ID . 22
find your phone number
and Private ID . . . . . . . 23
text messages . . . . . . 23
manage memory . . . . 27
use your phone as USB
mass storage device . 27
use your phone
as a modem . . . . . . . . 28
accessories. . . . . . . . . 30
for more information. . 30
main attractions . . . . . . 31
music player . . . . . . . . 31
media center . . . . . . . 40
camera . . . . . . . . . . . . 43
PTV features . . . . . . . . 47
one touch PTT . . . . . . 54
PT manager . . . . . . . .
MMS . . . . . . . . . . . . .
Mike’s wireless web
services . . . . . . . . . . .
bluetooth® . . . . . . . . .
clock screen saver . . .
basics. . . . . . . . . . . . . . .
display. . . . . . . . . . . . .
main menu . . . . . . . . .
text entry . . . . . . . . . .
navigation key. . . . . . .
handsfree speaker . . .
codes & passwords . .
lock & unlock phone . .
transmitters . . . . . . . .
use GPS with
map software . . . . . . .
contents
55
55
72
74
79
80
80
81
81
84
84
85
85
86
86
5
features for the
hearing impaired . . . . . 88
features for the
vision impaired . . . . . . 90
customize. . . . . . . . . . . . 92
volume. . . . . . . . . . . . . 92
ring tones . . . . . . . . . . 92
wallpaper . . . . . . . . . . . 93
datebook . . . . . . . . . . . 94
hide or show
location information. . . 94
calls. . . . . . . . . . . . . . . . . 96
turn off a call alert . . . . 96
recent calls . . . . . . . . . 96
redial . . . . . . . . . . . . . . 97
caller ID . . . . . . . . . . . . 97
call forward . . . . . . . . . 97
voice name . . . . . . . . . 98
emergency calls . . . . . 99
international calls. . . . 100
speed dial . . . . . . . . . 100
voicemail . . . . . . . . . . 100
6
contents
net alerts . . . . . . . . . .
other features . . . . . . .
advanced calling . . . .
alarm clock. . . . . . . . .
contacts. . . . . . . . . . .
datebook . . . . . . . . . .
GPS . . . . . . . . . . . . . .
handsfree . . . . . . . . .
memory card . . . . . . .
messages . . . . . . . . .
pc applications. . . . . .
personalize . . . . . . . .
TTY . . . . . . . . . . . . . .
security . . . . . . . . . . .
Safety and General
Information . . . . . . . . .
Service & Repairs . . . .
Specific Absorption
Rate Data . . . . . . . . . . .
102
103
103
104
105
106
107
108
109
110
111
111
112
112
116
121
122
Motorola Limited Warranty
for the United States
and Canada . . . . . . . . . 124
Hearing Aid
Compatibility . . . . . . . . 129
Information From the
World Health
Organization . . . . . . . . 131
Patent and Trademark
Information . . . . . . . . . 133
Privacy and Data
Security . . . . . . . . . . . . 134
Smart Practices
While Driving . . . . . . . . 135
index. . . . . . . . . . . . . . . 137
menu map
main menu
j Multimedia
L
E
1
B
p
• Shop
• Media Center
• Camera
• Audio Player (Music Player)
• Ring Tones
• VoiceRecord
Contacts
• [New Contact]
Messages
• [Create Message]
• Voice Mail
• Inbox
• Drafts
• Sent Items
• Fax Mail
• Net Alert
Web
Recent Calls
Push To Talk
• Call Alert
• PT Manager
• PTT Options
T
m
Games and Apps
• Alarm Clock Plus
• Music Player
• PhotoEditor
• iHelp
• Calculator Suite
• City Drift
• Java System
• OpenSourceNotices
Tools
• My Info
• My Name
• Line 1
• Line 2
• Private ID
• Group ID
• Carrier IP
• IP1 Address
• IP2 Address
• Profiles
• [New Profile]
• Standard
• Car
• Meeting
• Office
• Outdoors
• Headset
• PRVT Only
• CNTCS Only
• Alarm Clock Plus
u
• Bluetooth
• Audio Devices
• Pair to Devices
• Device History
• Setup
• Find Me
• GPS
• Position
• Privacy
• Interface
• Datebook
• [New Event]
• Call Timers
• Last Call
• Phone Reset
• Phone Lifetime
• Prvt/Grp Reset
• Prvt/Grp Lifetime
• Kbytes Reset
• Memo
Settings
• (see next page)
This is the standard main menu layout. Your
phone’s menu may be a little different.
menu map
7
settings menu
Display/Info
• Wallpaper
• Internal
• External
• Text Size
• Theme
• Mike
• Ruby
• Onyx
• High Contrast
• Home Icons
• Backlight
• Timer
• Java Timer
• Sensor
• Logo Flash
• PTT Backlight
• Clock
• Display: On/Off
• Screen Saver
• Time Format
• Date Format
• Year
• Menu View
• Icon View
• List View
• Tab View
• Large Dialing: On/Off
• Language
8
menu map
Phone Calls
• Set Line
• Any Key Ans
• Auto Redial
• Call Waiting
• Auto Ans
• Flip Activation
• Minute Beep
• Call Duration
• TTY
• Hearing Aid
• Notifications
• DTMF Dialing
• Call Forward
Personalize
• Reorder Menu
• Shortcuts
• Up Key
• Down Key
• Left Key
• Right Key
• Center Key
• Left Softkey
• Right Softkey
• Power Up
Volume
• Ringers/Alerts
• Speaker
• Earpiece
• Multimedia
• Keypad
Voice Playback
• Speak Text
• Speak Caller
• Voice
• Multimedia Volume
Memory Card
• Remove Card
• Store Media
• Format Card
• Help
Security
• Phone Lock
• Keypad Lock
• SIM PIN
• GPS PIN
• Change Passwords
Advanced
• Alert Timeout
• Headset/Spkr
• Connectivity
• Reset Defaults
• Return to Home
• Transmitters
• Phone Only
Connections
• Bluetooth
• USB
• Memory Card Access
• Data Modem
• Application Access
• GPS NMEA
• Help
Use and Care
Use and Care
To care for your Motorola phone, please keep it away from:
liquids of any kind
Don’t expose your phone to
water, rain, extreme humidity,
sweat, or other moisture.
dust and dirt
Don’t expose your phone to
dust, dirt, sand, food, or other
inappropriate materials.
extreme heat or cold
Avoid temperatures below
-10°C/14°F or above 45°C/113°F.
cleaning solutions
To clean your phone, use only a
dry soft cloth. Don’t use alcohol
or other cleaning solutions.
microwaves
Don’t try to dry your phone in a
microwave oven.
the ground
Don’t drop your phone.
Use and Care
9
essentials
Caution: Before using the phone for the first
time, read the Important Safety and Legal
Information located in the gray-edged pages
at the back of this guide.
about this guide
This guide shows how to locate a menu
feature as follows:
Find it: M > u > Phone Calls
This means that, from the home screen:
1 Press the menu key M to open the Settings
menu.
10
essentials
2 Press the navigation key
to scroll to
Phone Calls, and press the center key r to
select it.
symbols
This means a feature is network/
subscription dependent and may
not be available in all areas. Contact
Telus Client Care for more
information.
This means a feature requires an
optional accessory.
activate your Mike
account
Before you can begin using your handset, you
need to activate your Subscriber Identity
Module (SIM) card on The Mike Network.
Your SIM card holds the information required
to enable your handset to connect to The
Mike Network. It also stores your user
information, language preference and contact
list entries.
SIM card
insert the SIM card
Turn off your phone and remove your battery
before you install or remove a SIM card.
Carefully slide the SIM card into your
phone,until it lies flat in the SIM card holder.
• If you purchased your handset through
an Authorized Mike Dealer, your SIM
should already be active.
• If you purchased your handset at
another location, follow the “Getting
Activated” instructions in the Mike
Services User’s Guide.
essentials
11
Warning: To avoid loss or damage, do not
remove your SIM card from your phone
unless absolutely necessary.
entering the PIN
You may be required to enter a SIM PIN when
you first use your handset.
SIM card security
When you receive your handset, the SIM PIN
is 0000. Change your PIN to prevent
fraudulent use of the SIM card. See
“security” on page 112.
Your SIM card stores all your Contacts
information. Since this information is stored
on your SIM card, not in your handset, you
can remove the information by removing your
SIM card.
Note: Except for making emergency calls,
your handset will not function without the
SIM card.
To prevent unauthorized use of your handset,
your SIM card can be protected by a PIN that
you enter each time the handset is powered
on. You can change the PIN or turn off the
requirement that it be entered.
Note: Your PIN is set to OFF by default.
12
essentials
1 When the Enter SIM PIN Code screen appears,
enter your SIM PIN. An asterisk appears
for each character entered.
2 Press - under Ok.
Warning: If you enter your PIN incorrectly 5
times, your SIM card is blocked. To unblock
your SIM card, you must contact TELUS
Client Care.
memory card
loaded in the phone to save or delete music,
images, videos, or audio files.
A memory card is a removable flash
memory card that you can use to store
pictures, videos, and audio files. The memory
card can be inserted in your phone or
connected to your computer using the
memory card reader.1
Find it: M > u > Connections > USB
insert the memory card
1 Slide open the memory card slot cover.
Many types of pictures, videos, and audio
files stored on the memory card can be
viewed or played using your phone’s media
center. Music files can be played using the
music player.
You can connect your phone using a
Motorola data cable directly to your
computer, access the memory card
1. To order a memory card, memory card reader, or
memory card adaptor, log on to our Web site at
www.telusmobility.com or contact your Mike Dealer.
essentials
13
2 Slide in the memory card until it clicks into
place.
selecting the Remove Card option could result in
loss of data.
battery
Battery Use & Battery Safety
• Motorola recommends you always
use Motorola-branded batteries and
chargers. The warranty does not cover
damage caused by non-Motorola
batteries and/or chargers.
Note: The first time you insert a memory card
in your phone, you will see the following
options: [Do Nothing], Go To Music Player, Go To Camera,
and Go To Media Center. Select the option of your
choice and continue.
Warning: Do not remove the memory card
before selecting the Remove Card option under
Settings. Removing the memory card before
14
essentials
Caution: Use of an unqualified battery
or charger may present a risk of fire,
explosion, leakage, or other hazard.
Improper battery use, or use of a
damaged battery, may result in a fire,
explosion, or other hazard.
• Battery usage by children should be
supervised.
• Important: Motorola mobile devices
are designed to work best with
qualified batteries. If you see a
message on your display such as Invalid
Battery or Unable to Charge, take the
following steps:
• Remove the battery and inspect it to
confirm that it bears a Motorola
“Original Equipment” hologram;
• If there is no hologram, the battery
is not a qualified battery;
• If there is a hologram, replace the
battery and retry charging it;
• If the message remains, contact a
Motorola Authorized Service Center.
• New batteries or batteries stored for a
long time may take more time to
charge.
• Charging precautions: When charging
your battery, keep it near room
temperature. Never expose batteries to
temperatures below 0°C (32°F) or
above 45°C (113°F) when charging.
Always take your mobile device with
you when you leave your vehicle.
• When storing your battery, keep it in a
cool, dry place.
• It is normal over time for battery life to
decrease, and for the battery to exhibit
shorter runtime between charges or
require more frequent or longer
charging times.
• Avoid damage to battery and mobile
device. Do not disassemble, open,
crush, bend, deform, puncture, shred,
or submerge the battery or mobile
device. Avoid dropping the battery or
mobile device, especially on a hard
surface. If your battery or mobile
device has been subjected to such
damage, take it to a Motorola
essentials
15
Authorized Service Center before
using. Do not attempt to dry it with an
appliance or heat source, such as a hair
dryer or microwave oven.
• Use care when handling a charged
battery - particularly when placing it
inside a pocket, purse, or other
container with metal objects. Contact
with metal objects (e.g., jewelry, keys,
beaded chains) could complete an
electrical circuit (short circuit), causing
the battery to become very hot, which
could cause damage or injury.
Promptly dispose of used batteries in
accordance with local regulations.
Contact your local recycling center for
proper battery disposal.
Warning: Never dispose of batteries in a fire
because they may explode.
16
essentials
battery installation
1 Slide the release button back until it
releases the battery door.
2 Remove the battery door.
3 Push the battery down until it snaps in
place.
4 Replace the battery door and press it
gently until you hear a click.
battery charging
New batteries are not fully charged.
charge using the charger
1 Pull out the
connector cover, and
insert the charger
into mini USB
connector on your
phone as shown.
2 Plug the other end
of the charger into
the appropriate electrical outlet.
When you charge the battery, the battery level
indicator at the upper right of the screen
shows charging progress. At least one
segment of the indicator must be visible to
ensure full phone functionality while charging.
charge from your computer
You can partially charge your phone’s
battery by connecting a Motorola-approved
USB cable from your phone’s mini-USB port
to a high power USB connector on a
computer (not a low-power one, such as the
USB connector on your keyboard or buspowered USB hub). Typically, USB high-power
connectors are located directly on your
computer.
Note: The phone will be charged at a slower
rate than it is charged with the rapid charger.
Your computer must be turned on, and you
must have correct software drivers installed
on your computer. If the phone is off when
essentials
17
the USB cable is connected between the
computer and the phone, the phone will
power up in charging mode. This mode allows
the phone to charge fastest and quickest.
Note: If the battery is very low, the phone will
not turn On, but will continue to charge at a
low rate. The phone will power up in charging
mode when the battery has been charged to
approximately 5% of its capacity. For faster
charging under a very low battery condition, it
is recommended to use the rapid charger
supplied with the handset.
If the phone is turned on while charging from
a computer, it will not fully charge the battery.
In this case, the battery charge will be
maintained approximately between 80% and
95% of the battery's capacity. Cables and
software drivers are available in Motorola
Original data kits, sold separately.
TM
Tip: Motorola batteries have circuitry that
protects the battery from damage from
18
essentials
overcharging. Of course, unplugging the
charger from the wall will avoid current drain.
turn it on & off
To turn on your phone,
press and hold O for a
few seconds or until the
display turns on. If
prompted, enter your
four-digit unlock code.
To turn off your phone,
press and hold O for
two seconds.
Note: If you press the O for more than four
seconds, the handset will power “On” on
“transmitter off” mode. See “transmitters”
on page 86.
make a phone call
Enter a phone number and press N to make
a call or use of voice command. See“place a
call using voice name” on page 99.
To hang up press O or close the flip.
Tip: For best performance avoid touching the
antenna with your fingers during the call.
2 If you want to answer the call using the
ear speaker, just open the flip and press
N. To hang up press O or close the flip.
Note: You must have the Flip Activation
feature On. See “advanced calling” on
page 103.
answer a phone call
3 If you are using a Bluetooth headset, you
can press the answer key on your
Bluetooth headtset. To hang up press the
same key on your Bluetooth.
When your phone rings and/or vibrates, you
have the following options:
make a private call
1 If you want to answer the call on speaker
phone, press the speaker key t with
the flip closed. To hang up press the smart
key ..
With Mike’s Direct Connect service, you use
your phone as a long-range, digital 2-way radio
using one-to-one Private calls or one-to-many
group calls.
Your Private ID is the number at which you
receive one-to-one Private calls.
essentials
19
to make a private call
1 Enter the Private ID you want to call.
2 Press and hold the PTT button. Begin
talking after your phone emits a chirping
sound.
3 Release the PTT button to listen.
The recipient has the following options:
Option
Answer: Begin a Private call with the sender.
Queue: Store the call alert to the call alert
queue.
Clear: Dismiss and delete the call alert.
To end the call press O.
Note: A Private call ends automatically if
there is no activity on the call for a few
seconds.
send call alerts
Sending a call alert discretely lets the
recipient know that you want to talk to him or
her on a Private call.
When you send a call alert, the recipient’s
handset displays your name and emits a
series of beeps or vibrations.
20
essentials
to send a call alert
1 Enter the Private ID you want to call as
you would when making a Private call.
2 Press - under Alert.
When the message Ready To Alert appears on
the display, press the PTT button until the
message Alert Successful: appears.
answer a private call
1 When your phone emits a chirping sound
or vibrates to indicate you are receiving a
Private call, wait for the caller to finish
speaking.
2 Press and hold the PTT button and begin
talking after your phone emits a chirping
sound.
3 Release the PTT button to listen.
To end the call press O.
answer a call alert
or
3 Clear the call alert by pressing - under
Clear.
store a phone number
or private ID
You can store a phone number or private ID in
Contacts:
When you receive a call alert, you must
answer, queue, or clear it. You cannot receive
phone calls or Private calls until you do.
Find it: M > L > [New Contact].
to answer a call alert
1 Press the PTT button to start a Private call
with the sender.
2 Select a specific Ring Tone/Picture.
or
2 Queue the call allert by pressing - under
Queue.
1 Enter a name for the new entry. Each
entry’s name can contain 20 characters.
3 Select a type for the entry (Mobile, Work1,
Work2, Home, Fax, Pager, or Other). To store a
private ID choose Private.
4 Enter the number for the entry and press
- under Save when done.
essentials
21
Tip: Before saving the entry, you can save
more information. You can add a picture,
choose a special ringer, store an Email
address, an IP address, assign a Group, and
more. You can also create Contact entries that
are groups of Private IDs called Group IDs.
After you have saved the number, the new
Contacts entry is displayed.
call a stored phone
number or private ID
Shortcut: From the home screen press under Contcs.
or
Find it: M > L
1 Scroll to the Contacts entry.
Tip: You can set up your handset for two
different search options by pressing M >
22
essentials
Search Option. If you select Full Name Search, a
new window will appear to allow you to
type the name of the contact you are
looking for. If you select First Letter Search,
your handset will find the nearest match
to the letter you enter.
2 If the Contacts entry contains more than
one number, scroll left or right until the
type of the number you want to call is
displayed (Mobile, Private, Work1, Work2, Home,
etc.).
3 If you chose a phone number, press N to
call the entry.
or
If you chose a Private ID, or a Talkgroup ID,
press and hold the PTT button to call the
number.
Tip: If the Contacts entry you scrolled to
contains a Private ID, you can make an instant
Private call to that Private ID by pressing and
holding the PTT button, even if the Private ID
is not the type of number displayed.
find your phone number
and Private ID
Find it: M > m > My Info.
Tip: Want to see your phone number or
Private ID while you’re on a call? Press M >
My Info.
set it up
Before you begin using text messaging, you
may need to set up your signature, service
center number, and expiration information.
Shortcut: From the home screen press under Msgs > [Create Message] > M > Text Msg
Setup.
or
Find it: M > E > M > Text Msg Setup.
The following options become available:
text messages
Text messaging allows you send and receive
short text messages to and from other Mike
handsets. Messages you receive appear on
your handset’s display and in the text
message inbox.
option
Signature: Enter your signature (up to 11
characters long).
Delivery Report: Set it to On if you wish to
receive a report once the message has
been delivered.
essentials
23
option
Srvc Cntr No: Enter the phone number of your
service center. If you do not know this
number, contact your service provider.
Expire After: This is the amount of time
messages you send are saved at the
service center if they cannot be delivered.
After this period, they are discarded.
Auto Clean Up: Set this option to On if you want
your phone to delete sent messages.
If you set Auto Clean Up to On, select Clean Up After
to set the number of days after which sent
messages are deleted or the number of
messages to be kept.
option
Quick Notes: Are short, pre-written text
messages that you can create, edit, and
send in your text messages. You can store
up to 20 quick notes. A quick note may be
up to 30 characters long.
Select Quick Notes to create a [New Note] or
press - under Edit to change the prewritten quick notes.
Press - under Done to save the information
you entered.
receive a text message
1 To view the message press - under Read.
2 To dismiss the message notification press
- under Back.
Note: If your phone is powered off when you
receive a text message, your phone notifies
24
essentials
you the next time you power it on. If you are
out of your coverage area, your phone alerts
you when you return to your coverage area.
Tip: While reading a text and numeric
message that contains a phone number, you
can press S to call that number.
calling the sender, or storing the sender’s
number in Contacts, press M.
create and send text messages
1 From the home screen press - under
Msgs > [Create Message] > [Create Text Msg].
read from the message center
or
1 From the home screen press - under
Msgs > Inbox > Text Msg Inbox.
Select Inbox > Text Msg Inbox, or Sent Items > Text
Msg Outbox, or Drafts > Text Msg Drafts.
2 Select the message you want to read or
press the number of the message you
want to read. If the message fills more
than one screen, scroll to read it.
Tip: Scrolling through one message lets
you view the next message.
3 To reply to the message, press - under
Reply or to see all other choices, including
forwarding and deleting the message,
or
You can also create a text message from
the Inbox, Outbox or Drafts.
2 To address the message use the keypad
to enter the phone number of the person
you want to send the message to and
press r or press - under Contcs, or press
M > Recent Calls. Select the number you
want.
essentials
25
3 Select Msg: and enter the text of the
message or to use a quick note press under Browse and scroll to the quick note
you want.
2 To edit the fields you want to change,
follow step 2 through step 5 in “create
and send text messages” above.
4 Press M > Set Send Method and select Text,
Fax, x400, Paging, Email, ERMES, or Voice.
resend text messages
5 If you want to send the message, press
- under Send or to delete the message
without sending it, press - under Cancel.
Note: If you want to request confirmation
of delivery press M > Delivery Report > On.
Shortcut: From the home screen press under Msgs > Sent Items > Text Msg Outbox.
1 Scroll to the message you want to resend
or press the number of the message you
want to resend.
2 Press s > Resend.
use drafts
delete sent text messages
When you save a message as a draft, it is
saved in the drafts folder.
Shortcut: From the home screen press under Msgs > Sent Items > Text Msg Outbox.
Shortcut: From the home screen press under Msgs > Drafts > Text Msg Drafts.
1 Scroll to the message you want to delete.
1 Select the draft you want to edit. You also
have the choice to create new text
messages from this menu.
3 Press - under Yes to confirm.
26
essentials
2 Press - under Delete.
delete all unlocked sent messages
Shortcut: From the home screen press under Msgs > Sent Items > Text Msg Outbox.
1 Press M > Delete All.
2 Press - under Yes to confirm.
manage memory
Your text inbox, sent items, and drafts folder
have a set amount of memory available for
storing messages.
The text inbox holds 100 messages. If the text
inbox is full, you cannot receive messages
until you delete some.
The sent items and drafts folder hold 100
messages each. If the sent items and drafts
folder memory is full, you cannot send
messages or save drafts until you delete
some.
To view the amount of memory available in
your text inbox:
Shortcut: From the home screen press under Msgs > M > Text Msg Setup > Inbox Mem Mtr.
To view the amount of memory available in
your text sent items:
Shortcut: From the home screen press under Msgs > M > Text Msg Setup > Outbox Mem
Mtr.
To view the amount of memory available in
your drafts folder:
Shortcut: From the home screen press under Msgs > M > Text Msg Setup > Draft Mem Mtr.
use your phone as
USB mass storage
device
Find it: M > u > Connections > USB > Memory
Card Access
essentials
27
1 Slide open the
connector cover, and
insert the USB data
cable into the mini
USB connector on
your phone as shown.
2 Connect the other end
of the USB cable to
the USB port of the
computer.
3 Your memory card can now be accessed
by your computer.
Note: If you want to purchase and use
additional memory cards, Transflash and
MicroSD memory cards are compatible with
your handset, and available at
www.telusmobility.com or your local Mike
Dealer.
28
essentials
use your phone as a
modem
You can use your phone as a modem (Packet
Data only) with a laptop, handheld device, or
desktop computer. Circuit Data is not
supported. In order to use your handset as a
modem, you must create either a wired or
wireless connection between your handset
and the other device.
To connect your phone wirelessly, you must
have a Bluetooth adapter for the other device.
To create a wired connection, use a USB
cable.
connect with a USB Cable
use a USB cable to connect your handset to a
laptop, handheld device, or desktop
computer:
1 Pull out the connector
cover, and insert the
USB cable into the
mini USB connector
on your phone as
shown.
2 Insert the data plug
into the data port of
the other device.
When used as a modem, your handset is
enabled for Data Modem transfer mode, which is
used for small file transfers such as email.
Note: To use these services, you must install
the iDEN Wireless Data Services software
(available separately). For more information on
setting up your computer and your handset
for packet data calls, contact TELUS Client
Care.
connect via
Bluetooth
Use your handset as a modem via Bluetooth.
The laptop, handheld device, or desktop
computer you want to connect to must have a
Bluetooth adapter installed.
Check that the adapter is properly installed,
and then follow the specific instructions
outlined in the device’s user guide to connect
the device to your handset.
essentials
29
accessories
Your handset comes with a battery, and
a charger.
To order additional accessories, log on to our
Web site www.telusmobility.com or
contact your Mike Dealer.
for more information
If you have questions about your i877
handset, contact your Mike Dealer or TELUS
Client Care.
30
essentials
main attractions
music player
Your phone includes a music player that you
can use to play music files stored in the Music
directory on the memory card inserted in your
phone.
The music player groups the music files into
folders and lists. When you select a music file
to play, the music player plays this file, then
plays the other music files grouped with it.
The music player also plays podcasts you
download to your computer and then save on
the Podcast directory on your phone’s
memory card. You can mark highlights within
a podcast file to help you find the parts you
most want to listen to.
You can send details of the podcast to a friend
and send feedback to the podcast creator
using MMS messages.
Audio files supported by the music player
include:
Format
Bit Rate
AAC
.m4a, .aac
AAC+
.m4a, .aac
Up to
320kbps
Up to
128 kbps
Sampling
Rate
Up to
48 kHz
Up to
48 kHz
MP3
.mp3
(16 to 128
kbps)
Up to
320kbps
Up to
48 kHz
main attractions
31
Format
Bit Rate
WMA v9 L2
WMA v3, v7, v8
.wma
Up to
320 kbps
Sampling
Rate
Up to
48 kHz
understanding the folder
structure
When you first insert the memory card into
your phone, five folders are created: Audio,
Image, Music, Podcast, and Video. In order to view
files stored on the memory card, you must
store the given file in its corresponding format
folder: audio files such as ring tones, and
voice recordings to the Audio folder, pictures to
the Images folder, music files such as songs to
the Music folder, Podcasts to the Podcast folder
and videos to the Video folder.
filename rules
When naming files stored on the memory
card, the following rules apply:
• The filename can only contain ASCII
characters.
• The filename can be up to 32
characters long, including the file
extension.
Warning: If a music file name is longer than
32 characters, including the file format (.MP3),
the song will not be visible on the player and
therefore can not be played. This can be
corrected by renaming the file and replacing it
on the card.
play music files
Find it: M > j > Audio Player.
1 Scroll to a folder.
32
main attractions
Tip: The Songs folder contains all the
music files on the memory card in a single
list.
2 To play the first music file in the folder,
press - under Play. (If the selected folder
contains subfolders, this plays the first
music file in the first of the subfolders.)
Press r to view the folder’s contents.
Scroll to a music file and press - under
Play, or scroll to a folder and press under Play to play the first music file in it.
Any time you are viewing a list of folders with
the music player, you can scroll to a folder and
press - under Play to start playing the
contents of that folder or press r to view
the contents of the folder.
play music while loading files
The first time the music player finds music
files on your memory card, it loads and
organizes these files. This may take a long
time for a large number of files.
To play music while files are loading:
Find it: M > j > Audio Player.
1 Press - under View.
1 Scroll through songs and folders while
loading is going on the background.
2 Scroll to a music file or folder and press
- under Play or r.
To stop viewing a folder and return to the
folder or list that contains it, press - under
Back.
main attractions
33
The following options become available
through the navigation panel:
option
Pause and Resume
Press - under Pause or r to pause, and
press - under Play or rto resume playing
paused music files.
Skip to Next or Previous
Press and release
right or left to skip to
the next or previous music file. (Do not hold
the left side of the navigation key.)
Fast Forward and Rewind
Press and hold
right or left for 2 seconds
to fast forward or to rewind.
set up the music player
Find it: M > j > Audio Player > M> Setup
34
main attractions
The music player can be set up with the
following options:
Option
Repeat: lets you set the music player to play
one or all the music files in a list or folder
repeatedly. While in the music player press
M > Setup > Repeat > All or One.
Shuffle: lets you set the music player to play
the music files in a list or folder in random
order. While in the music player press M >
Setup > Shuffle: > On or Off.
Visuals lets you customize the look of the
music player background screen by
choosing a theme or by viewing visuals.
While in the music player press M > Setup >
Visuals > On or Off.
Option
3D Music lets you experience surround
effects. While in the music player
press M > Setup > 3D Music.
If you set the 3D Music feature to On, you can
select a 3D effect from the list of Music
Reverbs.
Equalizer lets you customize the sound of the
music player when the handset is tethered
to a stereo headset. While in the music
player press M > Setup > Equalizer, and select
the mode you want.
Option
Use Bluetooth lets you route the audio
from the music player to a wireless
Bluetooth stereo headset. Additionally the
handset can be connected to a Bluetooth
Home Stereo Adapter to stream content
from your home entertainment system and
listen wirelessly from your headset
withouth missing a call. While in the music
player press M > Setup > Use Bluetooth.
work with playlists
Playlists are lists of music files you create
from the files already available through the
music player.
Playlists enable you to organize music files,
but they do not change anything in other
folders or on the memory card. Adding or
deleting a file on a playlist does not copy,
delete or move it.
main attractions
35
create a playlist
Find it: M > j > Audio Player > Playlists > [Create
New].
1 Enter a playlist name.
Note: If you do not assign a name, the
playlist is named Playlist followed by a
number. For example, the first playlist you
create without naming is automatically
named Playlist-1.
2 Select [Add Songs].
A list of all music files on the memory
card appears.
Tip: For options to help you sort through
this list, press M.
3 Select each file you want on the playlist. A
checkmark appears by each selected file.
Tip: To deselect a selected item, scroll to
a selected file and press r.
36
main attractions
4 When you are finished selecting files,
press - under Done and - under Save.
The following options are available for existing
playlists:
option
Edit a Playlist
After you create a playlist, you can change
its name, add music files, remove music
files, and change the order of the music
files in Music Player > Playlists > M > Edit Playlist.
Make changes and press - under Save.
Reorder Songs in a Playlist
You can change the order of the music files
while creating or editing the playlist in Music
Player > Playlists > M > Edit Playlist > M >
Reorder Songs. Scroll to the song you want to
move and press - under Grab; then scroll to
the place where you want the song to
appear and press - under Insert.
option
Remove Songs
option
Delete a Playlist
You can remove some or all music files
while creating or editing a playlist.
While in the music player select Playlists.
Scroll to the playlist you want to delete and
press M > Delete Playlist. Press - under Yes
to confirm.
Delete all Playlists
Before you have saved a new playlist or
while editing a playlist, press M and scroll
to the song you want to remove and press
M > Remove Song and press r, or you can
select Remove All Songs: press - under Yes to
confirm and - under Save.
Reorder Playlists
You can change the order of the playlists in
the Playlists folder. Press M > Edit playlist >
Reorder Playlists. Scroll to the playlist you want
to move and press - under Grab; then scroll
to the place where you want the playlist to
appear and press - under Insert.
While in the music player select Playlists.
Press M > Delete All Playlists and press Yes under to confirm.
Note: This deletes all playlists except the
Favorites playlist.
use the favorites playlist
The Favorites playlist is a permanent playlist. You
can Add To Favorites, remove and change the
order of the music files, but you cannot
rename or delete music files.
Find it: M > j > Audio Player > Songs.
main attractions
37
Select the song you want to add to your
favorites and press M > Add To Favorites.
work with podcasts
Find it: M > j > Music Player > Podcasts.
Note: The Podcasts folder is empty until you
download podcasts from your computer.
1 Scroll to view individual podcast episodes
or folders containing multiple episodes of
the same program.
2 Press r to view the podcast episodes
within a folder or the details screen of an
individual podcast episode.
You can pause, resume, fast-forward, and
rewind just as with any other music file.
Some functions differ when playing a podcast:
• Pressing r when you have scrolled
to a podcast displays a screen showing
podcast details, but does not play the
38
main attractions
podcast. To play the podcast, press Play.
After you begin playing the podcast,
pressing r pauses and resumes the
podcast.
• If the podcast you are playing contains
highlights, pressing and releasing the
right or left r skips to the next or
previous highlight within the podcast,
or to the beginning or end of the
podcast.
highlights
Highlights are portions of a podcast that are
marked to help you find them more easily.
Some podcasts you download may already
have highlights marked. You can use the
music player to add and delete highlight
markers. Press and release (don’t hold) the
right or left to find them.
You can play all the highlights in a podcast and
skip everything that is not marked as a
highlight using Highlights Only.
add a highlight marker
1 While playing a Podcast press M > Add
Highlights.
2 Press - under On to mark the beginning.
3 Go to the point in the podcast that you
want to mark as the end of the highlight
and press - under Off.
4 Press - under Back.
an MMS message that the person can save
and download onto their computer.
If played on a phone with a music player, like
yours, they will see any highlight markers
created within the podcast.
Find it: M > j> Audio Player > Podcasts > M >
Forward Details > Send.
Note: If the podcast has no highlights, this
option will not be displayed.
background music
Tip: Highlight markers can be deleted by
pressing M > Clear or pressing M > Edit
Highlights > M > Clear All Highlights from the
Podcasts menu.
Your phone has the capability to play music in
the background while you are acessing other
features like Settings, Media Center, Bluetooth, GPS,
Contacts, MMS, Datebook, Memo, Recent Calls, and
others.
send podcast information
If you want to share a podcast you have
saved to your memory card, you can send it in
You can also enjoy listening to your favorite
background music while browsing the web,
reading news or checking the weather.
main attractions
39
play music in the background
Find it: M > j> Audio Player > Songs.
• Musical ring tones in the list of ring
tones
1 Select a music file and press r to play
the song.
• Audio recordings saved from MMS
messages received
2 Press M > Hide Player.
• Audio recordings downloaded to your
phone
The music player continues playing and the
handset returns to the home screen. To jump
back to the music player, press - under Player.
media center
The media center lets you access pictures,
videos, and audio recordings stored in your
phone’s memory or in the Audio, Image and
Video folders on a memory card inserted in
your phone’s memory card slot.
The following audio recordings can be
accessed through the media center:
• Voice records
40
main attractions
Because the memory card inserted in your
phone may contain files saved to it using a
device other than your phone, not all types of
pictures, videos, and audio recordings on the
memory card may be accessed through your
phone’s media center.
Items in the media center can be sent in
MMS messages and with Bluetooth. See
“MMS” on page 55 and “bluetooth®” on
page 74.
Pictures in the media center can be sent in
Private calls using Send via PTT. See “PTV
features” on page 47.
Media files supported by the Media Center
include:
Format
Bit Rate
AMR-NB
4.75 kbps – 12.20
kbps (supports all
3GPP specified
rates)
.amr, .3gp,
.3ga, .mp4
AMR-WB
.awb, .3ga,
.3gp
AAC
(MPEG4
AAC-LC)
Sampling
Rate
.aac, m4a,
.3ga, .mp4
Bit Rate
Enhanced Up to 128 kbps
(16 to 128 kbps)
AAC+
Sampling
Rate
Up to
48 kHz
.aac, .m4a,
.3ga, .mp4
MP3
6.6 kbps - 23.85
Kbps (supports all
3GPP specified
rates)
8 kHz
.mp3,
.mpga
Up to 320kbps
16 kHz
8-bit
Linear
PCM
Up to 320kbps
Up to
48 kHz
Up to 1536kbps
Up to
48 kHz
Up to 1536 kbps
Up to 48 kHz
(8, 11.05, 12,
16,22,24,3,44,
48 kHz)
Up to 704 kbps
Up to
48 kHz
.waw, .au
16-bit
Linear
PCM
.aac , .3gp,
.m4a, .3ga,
.mp4
AAC+
Format
.waw, .au
Up to 128 kbps
(16 to 128 kbps)
Max: 48 kHz
8-bit Alaw PCM
.waw, .au
main attractions
41
Format
Bit Rate
Sampling
Rate
Format
Bit Rate
Sampling
Rate
8-bit mulaw PCM
Up to 704 kbps
Up to 44 kHz
(8, 11.05, 12,
16, 22,44 kHz)
iMelody
1 – 3.5 kHz
Monophonic
N/A
.waw, .au
WMA v9
L2 (also
WMA v3,
v7, v8)
Up to 320 kbps
48 kHz
.wma
N/A
Stand
MIDI
N/A
.mid, .midi,
.smf
XMF MIDI N/A
.xmf, .mmf,
.xmf0,
.xmf1,
.mxmf
42
main attractions
N/A
.imy
Supported video file formats include:
Format
MPEG4 + AMR-NB
MPEG4 + AMR-WB
MPEG4 + AAC / AAC+ /
Enhanced AAC+
H.263 + AMR-NB
H.263 + AMR-WB
H.263 + AAC / AAC+ /
Enhanced AAC+
Extension
.mp4, .3gp
.mp4, .3gp
.mp4, .3gp
.3gp
.3gp
.3gp
camera
The 1.3 MP camera with a digital, external
viewfinder in your phone, takes pictures and
records videos. You can save these pictures
and videos in your phone’s memory or to a
memory card inserted in your phone’s
memory card slot, depending on the storage
preference you chose. You can access these
saved pictures and videos through the media
center.
You can send the pictures you take either in
Private calls or with Bluetooth. You can also
assign them to Contacts entries, or set them
as your phone’s wallpaper.
Note: If you insert a memory card into the
phone now, you are prompted to save the
picture you have just captured to the memory
card. Choosing to save the picture to the
memory card does not change your storage
preferences after the picture is saved.
To save the picture, press r.
To discard the picture without saving it, press
- under Discard.
From the camera viewfinder, you can press
M to enter Menu Options.
access the camera
There are many ways to access the camera.
The simplest way is to press e.
To take pictures aim the camera lens on the
flip and press - under Capture or press r.
main attractions
43
The following options become available:
option
Record Video
Recording a video is similar to taking a
picture. If you store videos in phone
memory, you can record videos up to 60
seconds long. If you record video onto the
memory card, the video length is limited by
how much memory is available on the card
or one 2 hours.
Zoom
Set the zoom to 1x, 2x, or 4x. You can also set
zoom from the viewfinder by pressing
up and down.
Spotlight Setting
Turn on the spothlight ON before taking a
picture in low light conditions. Set it up to
be Always On or Off.
44
main attractions
option
Self Timer
Delay capturing the picture for a selected
number of seconds. The values are: Off
(default), 10 seconds, 15 seconds, 20 seconds.
To turn off the timer before the picture is
captured, press - under Cancel.
Picture Quality
Adjust the picture quality to Normal or Fine.
Picture Size
Set up the picture size to Max, Xlarge, Large,
Medium, Small, Wallpaper1, or Wallpaper2. You can
also set picture size from the viewfinder by
pressing
left and right.
digital viewfinder
The external digital
viewfinder allows you
to take self-portraits
with convenience and
accuracy compared
to a mirror.
To take self-portraits
press e, close the
flip and press the
speaker phone key to
capture the picture.
When you finish
taking pictures, press
the smart . key to exit the self-portrait
camera mode.
photo editor
Your phone comes with a photo editing Java
application that allows you to edit your
pictures with crop, resize, flip and color
adjustment tools. You can also add graphics
and text to your pictures.
Find it: M > j > Media Center.
1 Select the picture you want to edit.
2 Press M > Edit.
or
Find it: M > T > PhotoEditor.
change storage preference
You can choose whether media items are
saved to your phone’s memory or to the
memory card. From the camera viewfinder
press M > Memory Card > Store Media.
1 Select On Phone or Prefer On Card.
The location that you choose becomes the
Store Media option in Settings.
main attractions
45
access the media center
customize the camera
You can access the media center from the
camera at any time by pressing M > Media
Center, except when you are using the Camera
Setup menu or viewing the memory screen.
The Camera Setup menu lets you customize the
camera as follows:
Press M > Media Center.
The media center contains all your pictures,
music and video files located on your phone’s
memory or your removeable memory card.
Use the * or the # to filter your results.
option
Ask for Name
If this option is On, you are prompted to
enter a name for each picture before saving.
Otherwise, pictures are automatically saved
with the date and a number as their names.
Shutter Sound
Set the default sound for the Shutter Sound.
Spotlight Setting
Select Always On or Off, depending on the
lighting condition.
Default Size
Sets the default value for the Picture Size
option.
46
main attractions
option
Default Quality
Sets the default value for the Picture Quality
option.
PTV features
Push to View (PTV) lets you exchange
the following items through Private calls
with other phones that have this capability:
• Short text messages1
• Pictures1
• Datebook events
• My Info
• Contact information
• Location information1
You can choose to send messages, pictures,
events, My Info, contacts or location
information to the Private ID you are engaged
in a Private call with, Private IDs on the Recent
Calls list, and Private IDs stored in Contacts.
When you make or receive a Private call, your
phone automatically determines whether the
phone you are engaged in a Private call with is
able to receive each of these items. Your
phone saves this information for as long as
the Private ID is on your Recent Calls list or is
saved in your Contacts. Your phone updates the
saved information each time you make or
receive a call to or from that Private ID.
You can turn your phone’s ability to send and
receive messages, pictures, events or
location information On and Off.
Note: You cannot send PTT feature items
during Talkgroup calls.
1. Additional charges may apply.
main attractions
47
send messages
The Push to View Messages feature lets
you send short text messages through
Private calls.
When you send a message, it appears on the
display of the phone you are engaged in the
Private call with. After the call, the message
appears in the Recent Calls list of that phone.
begin a message and choose a
recipient
You can begin a message during a Private call,
from the Contacts list, the Recent Calls list, or from
the PT Manager.
begin a message during a private call
While in a Private call, press M > Use PTT Feature
> Send Message.
48
main attractions
begin a message from the contacts or
the recent calls list
1 From the Contacts or the Recent Calls list,
select the entry containing the Private ID
you want to send the message to.
2 Press M > Use PTT Feature > Send Message.
begin a message from the PT Manager
The PT Manager lets you select the Private ID
you want to send the message to from Contacts
or the Recent Calls list.
Find it: M > p > PT Manager > Send Message.
Then select A Contact or A Recent Call to see a list
of entries from the Contacts or the Recent Calls list
that can receive messages.
create messages
After you have begun a message and chosen
a recipient, a screen appears that lets you
create the text of the message you want to
send. Your message may be up to 400
characters long.
reply to a message
You can choose from a list of ready-made
words or short phrases called Quick Notes.
You can use a Quick Note as it is or edit it
before you send it. Editing a Quick Note
changes the Quick Note for this message only
and will not change the Quick Note on the list.
2 Press - under Reply.
send a completed message
After you have completed your message,
press the PTT button to send it.
receive messages
When you receive a message, a message
notification appears on the display.
To view the message: Press - under Read.
1 View the message.
3 Create the message and push the PTT
button to send it.
send pictures
You can send pictures stored in the Media
Center through Private calls. The picture
you send appears on the Private call
recipient’s display.
If the recipient accepts the picture, their
phone saves the picture. The picture then
appears in that phone’s recent call list.
Note: You cannot make or receive Private
calls while transmitting or receiving a picture.
To dismiss the message press - under
Dismiss.
main attractions
49
send a picture during a call
2 Select the picture you want to send.
1 While in a Private call, press - under
Picture or press M > Use PTT Feature > Send
Picture.
3 Press M > Send Via... > Send Via PTT.
A list of pictures that can be included in a
Private call appears.
4 Select A Contact or A Recent Call
A list of contacts that have Private IDs and
are able to receive pictures appears.
2 Select the picture you want to send.
5 Select the name of the person you want
to send the picture to.
3 Press the PTT button to send the picture.
6 Press the PTT button to send the picture.
4 Wait while the picture is transmitted. The
Private call is temporarily interrupted
while a picture is transmitted.
7 When prompted, press the PTT button to
resume the Private call.
5 When prompted, press the PTT button to
resume the Private call.
from the PT manager:
Find it: M > p > PT Manager > Send Picture.
1 Select A Contact or A Recent Call
start a call by sending a picture
from the media center
Find it: M > j > Media Center
1 Scroll left or right to Media: Pictures
50
main attractions
A list of contacts that have Private IDs and
are able to receive pictures appears.
2 Select the name of the person you want
to send the picture to.
3 Select Browse Picture or Capture Picture.
clear a picture from the display
4 Press the PTT button to send the picture.
If you want to clear a picture from your
phone’s display while still on a call, press M >
Clear Screen.
5 Once picture has been sent, when
prompted press the PTT button to resume
the call.
receive a picture
When someone sends you a picture, your
phone emits a tone or vibrates and a message
appears asking if you want to accept the
picture.
Pictures you receive are saved to your phone’s
memory or a memory card. They are
accessible through the media center.
When you see a message asking if you want
to accept the picture, press Yes to accept or No
to decline.
The picture will not appear on the display
again the next time you receive a call from
person who sent it. This does not delete the
picture from My Pictures.
send My Info
1 While in a Private Call press M > Send My
Info via PTT, and push the PTT button to
send.
or
2 From the home screen press M > m >
My Info > M > Send My Info via PTT and push
the PTT button to send.
Tip: If you want to stop the transmission
before it is finished, press E.
main attractions
51
set my info sending option
You can control what portion of the
information in My Info is sent and
whether it is sent automatically in every call or
only when you choose to send it.
Find it: M > p > PT Manager > Configure > PTT
My Info > Info to Send
1 Select or remove the fields you want to
send.
2 Press - under Done.
The information your phone sends always
includes My Name and Private. You may also send
Line 1, Line 2, and Carrier IP, depending on your
sending options.
automatic sending
To control whether you send your information
automatically:
Find it: M > p > PT Manager > Configure > PTT
My Info > Auto Send
52
main attractions
1 Select On or Off
2 When you make a call in which your
information is sent automatically, the
name you entered in the My Name field of
My Info appears on the display of the
recipient’s phone, even if your name and
Private ID are not stored in the recipient’s
Contacts.
send contact information
1 While in a Private Call press M > Use PTT
Feature.
2 Select Send Contact and select the contact
information you want to send.
3 Push the PTT button to send.
or
1 From the home screen press M > p >
PT Manager > Send Contact.
2 Enter the Private ID number of the person
you want to send the Contact information
to or press - under Browse.
A list of contacts that have Private IDs and
are able to receive pictures appears.
3 Select from Recent Calls, Contacts, or Memo.
2 Select the name of the person you want
to send your location to.
4 Select the contact information you want
to send and push the PTT button.
3 Press the PTT button to send your
location.
send your location
Note: The location information can be stored
in the recipient’s recent call list.
You can transfer your approximate
location information through Private
calls to other enabled phones. Using the
integrated GPS feature the following location
information can be shared:
• Time Stamped Latitude/Longitude
• Relative Location or Direction and
distance from the sender in Miles or
Kilometers
Find it: M > p > PT Manager > Send Location.
turn PTT features on and off
You can turn your phone’s ability to send and
receive messages, pictures, and Datebook
events on and off.
You cannot turn your phone’s ability to send
and receive My Info and contact information
on and off.
Find it: M > p > PT Manager > PTT Options > On/
Off PTT Features.
1 Select A Contact or A Recent Call.
main attractions
53
4 Check or uncheck Messages, Pictures
Events and/or Location.
one touch PTT
Find it: M > p > PTT Options > One Touch PTT.
One Touch PTT sets your phone to do any of
the following each time you press the PTT
button from the home screen
option
Off
Nothing happens when you press the PTT
button from the home screen.
Last Call
Call the most recent Private ID or Group on
the recent calls list.
54
main attractions
option
Assigned Number
Call a Private ID you assign. Enter the
number using your keypad, or press under Search. Select Contacts, Recent Calls, or
Memo.
If you are entering a Talkgroup number,
press # before the number.
PT Manager
Go to PT Manager. See “PT manager” on
page 55.
Send Event
Go to the first screen to send a Datebook
event.
Send Message
Go to the first screen to send a message.
See “send messages” on page 48.
option
Send Picture
Go to the first screen to send pictures. See
“send pictures” on page 49.
Send My Info
Go to the first screen to send My Info.
Send Contact
Find it: M > p > PT Manager
1 Select Send Message, Send Picture, Send Event, Send
My Info, Send Contact or Send Location. After
choosing what PTT item you are sending,
select a contact and press the PTT button
to send.
or
Go to the first screen to send a contact.
Send Location
2 Select Configure to configure your PTT Quick
Notes, PTT My Info, PTT Location, One Touch PTT, or
On/Off PTT Features.
Go to the first screen to send your location.
See “send your location” on page 53.
MMS
PT manager
The PT Manager lets you quickly access PTT
features, and other Private call features, from
the main menu.
You can also set the One Touch PTT feature
from the PT Manager.
Multimedia Messaging Service (MMS) lets
you send and receive messages that may
include text, pictures, videos, and audio
recordings.
Your phone supports MOSMS as well as
MMS. You should see no significant
differences between the two; some names of
main attractions
55
menu items and the steps you take to access
features may differ.
create a message
Tip: To remove a phone number or email
address from the list of message recipients,
scroll to the phone number or email address
and press - under Remove.
Shortcut: From the home screen press under Msgs > [Create Message] > [Create MMS Msg].
When you are finished addressing the
message, press - under Back.
or
To enter or edit the body of the message:
Find it: M > Messages > [Create Message] > [Create
MMS Msg].
1 Select Message.
Note: You can also create a message from
Contacts, Recent Calls, or the home screen.
To address the message:
2 Enter text using the keypad or press under QNotes to select a quick note of your
choice (see “quick notes” on page 58)
and press r.
1 Select To:
more message options
2 Add the phone number or email address.
To view more message fields in a message
you are creating, select ...More...
or
3 Select from Contacts or Recent Calls.
4 Press r.
56
main attractions
The following options become available:
option
Subject
Create or edit the subject line.
Attach
option
Report
Set receipt confirmation On Delivery.
Valid Until
Set a date after which attempts to deliver
the message end. Or press - under No Date.
Attach a picture, audio file, video or voice
record.
Cc
reply to a message
Send a copy of this message to someone
else.
Auto Replies
You can reply to a message while you are
viewing it, or while a previously viewed
message is highlighted in the message
center. You cannot reply to unread messages.
Allows you to create a list of possible short
answers for the recipient to choose when
replying to your message.
Priority
To reply to a message:
Set priority Normal or High.
1 View the message you want to reply to.
2 To reply to the sender only, press Reply or
Reply All.
main attractions
57
3 A list of short phrases appears. Select any
of these phrases to add it to your
messages or select [Create Reply].
4 Edit any message fields you want to
change.
5 Press - under Send.
quick notes
When you are filling in the Message and Subject
message fields, you can add ready-made
words or short phrases called Quick Notes.
After you add these words or phrases, you
can edit them as you would any other text.
1 While you are creating a message, scroll
to or select Message or Subject.
insert a picture, video, and
audio recording from the media
center
You can insert one or more pictures, videos,
and audio recordings from the media center
into the body of the message. You can include
text in the body of your message in addition
to these items.
insert items
While you are filling in the Message field, press
M and select Insert QuickNotes, Insert Picture, Insert
Audio, Insert Video, Capture Video, Capture Picture or Record
Voice.
2 Press - under QNotes.
A list of available pictures, videos, and audio
recordings appears.
3 Select the quick note you want to insert
into the message.
Select the picture, video, or audio recording
you want to insert.
58
main attractions
Tip: To view or listen to the item before
inserting it, highlight it and press Preview.
remove an inserted item
To remove an item from the message you are
creating, highlight it and press - under Delete.
attach a picture, video, and
audio recording from the media
center
You can attach one or more pictures, videos,
and audio recordings from the media center.
3 Select the picture, video, or audio
recording you want to attach.
Tip: To view or listen to the item before
attaching it, highlight it and press under Preview.
If you want to attach more items, select
[New Attachment].
4 When you are finished, press - under
Done.
take a new picture
1 When you are filling in the message,
select Attach > [New Attachment].
1 While you are creating a message, scroll
to any message field and press M or
select Attach > [New Attachment].
2 Select Browse Pictures, Capture Picture, Browse
Audio, Record Voice, Browse Video, or Record Video.
2 Select Capture Picture. This accesses the
camera.
A list of available pictures, videos, and
audio recordings appears.
Tip: If you want to adjust the zoom,
spotlight, picture quality, picture size, or a
timer, set these options before taking the
picture.
main attractions
59
3 Take the picture. For instructions on how
to take pictures, see “camera” on
page 43.
4 When you have captured the picture you
want, press Save. This will automatically
save it to your media center and attaches
it to your message.
To discard the picture, press - under
Discard. You can then take another picture.
5 When you are finished, press - under
Done.
The picture is attached to the message
and saved to the default storage location.
To view the video without saving it, press
Review.
3 To save the video, press e or press r.
To discard the video without saving it,
press Discard.
4 The picture is attached to the message
and saved to the default storage location.
create a new voice record
You can create a new voice record to send
with a message:
1 Press M or select Attach > [New Attachment].
2 Select Record Voice.
record a video
You can record a video to send with a
message:
1 Select Attach > [New Attachment].
2 Record and adjust video.
60
main attractions
3 Say the message you want to record into
the microphone.
4 When you are finished recording, press
r.
5 When you are finished, press - under
Done.
The voice record is attached to the message
and saved to the media center and the list of
voice records.
remove an attachment
To remove an attachment in a message you
are creating:
1 Select Attach.
2 Scroll to the attachment you want to
remove.
3 Press M > Unattach.
drafts
While you are composing a message, you can
save it in the MMS drafts folder by pressing
M > Save In Drafts.
You can continue to create the message. The
version you saved in the MMS drafts folder
will not change.
send a draft
Shortcut: From the home screen press under Msgs > Drafts > MMS Drafts.
1 Select the draft you want to send.
2 Press - under Send.
Note: If Send does not show as an option,
you might need to complete required
fields in the message in order to send it.
edit a draft
Shortcut: From the home screen press under Msgs > Drafts > MMS Drafts.
1 Select the draft you want to edit.
2 Press r.
main attractions
61
delete a draft
When you send a draft, it is removed from the
MMS drafts folder.
1 To delete a message in the MMS drafts
folder without sending it, scroll to the
message you want to delete and press under Delete.
2 Press - under Yes to confirm.
3 Make editions if you wish, select the
recipient and press - under Send.
resend
If a message was not sent from your handset,
you can resend it.
Shortcut: From the home screen press under Msgs > Outbox > MMS Outbox.
1 Scroll to the message you want to resend.
MMS outbox
2 Press - under Resend.
MMS messages you have sent or tried to
send are stored in the MSS Outbox.
Note: If your message was sent successfully,
Resend will not appear as an option.
forward items from the outbox
check delivery status
Shortcut: From the home screen press under Msgs > Outbox > MMS Outbox.
1 Scroll to the message you want to
forward.
2 Press M > Forward.
62
main attractions
If a message was successfully sent and you
set the message to give a report confirming
delivery, you can check the delivery status:
Shortcut: From the home screen press under Msgs > Outbox > MMS Outbox.
1 Scroll to the message you want to view.
2 Press M > Delivery Status.
delete a message
1 Scroll to the message you want to delete.
2 Press M > Delete Message.
3 Press - under Yes to confirm.
receive a message
When you receive an MMS message, a
message notification appears on the display.
1 To view the message press r.
If your phone is set to download new
messages automatically, the message
downloads from the message server now.
2 If your phone is set prompt you before
downloading new messages, press M.
3 If the message fills more than one screen,
scroll to read it.
embedded objects and
attachments
Messages may contain pictures, videos, or
audio recordings as part of the body of the
message or as attachments.
If a message contains pictures, videos, or
audio recordings in the body of the message,
highlight each picture, video, or audio
recording to view or play it.
If a message contains a picture, video, or
audio recording as an attachment, open the
attachment to view the picture or play the
video or audio recording.
open attachments
To open an attachment:
1 View the message.
main attractions
63
2 Highlight the attachment you want to
open. Attachments appear at the end of a
message.
3 Press r.
Note: Attachments that are of an unknown
type cannot be opened, but they can be
deleted.
2 Press - under Delete and - under Yes to
confirm.
forward a message
1 Press M > Forward.
2 Create and send your message.
Embedded objects and attachments are
included when you forward a message.
view received messages from
the message center
lock and unlock messages
Shortcut: From the home screen press under Msgs > Inbox > MMS Inbox.
Locked messages cannot be deleted until you
unlock them.
Select the message. If the message has not
yet been downloaded from the message
server, it is downloaded now.
1 View the message you want to lock or
unlock.
delete unread messages
call a number in a message
1 Scroll to the message you want to delete.
If a message you receive contains a phone
number, Private ID, or Talkgroup ID in the From
64
main attractions
2 Press M > Lock Message or Unlock Message.
field, the To field, the Cc field, the Subject line, or
the body of the message, you can call or send
a call alert to that number.
store message information to
contacts
2 Highlight the Private ID or Talkgroup ID
you want to alert.
If a message you receive contains a phone
number, Private ID, Talkgroup ID, or an email
address in the From field, the To field, the Cc
field, the Subject line, or the body of the
message, you can store this information to
Contacts.
3 Press M > Alert.
1 View the message.
4 Push the PTT button.
2 Highlight the number or email address
you want to save.
make a group call
3 Press M > Save Number or Save Email.
1 View the message.
4 To store the number or email address as a
new entry, select [New Contact].
send a call alert
1 View the message.
2 Press M.
3 Highlight the Talkgroup ID you want to
call.
4 Select Talkgroup.
5 Push the PTT button.
To store the number or email address to
an existing entry, select the entry.
5 With the Contacts type field highlighted,
press
left or right to display the
main attractions
65
Contacts type you want to assign the
number or email address.
6 Press - under Save.
A slide show may contain a series of pictures
that display in sequence. It may also include
one or more audio recordings.
go to a website
When you view a message containing a slide
show, this icon i appears.
If a message contains one or more website
URLs, you can go to that website.
view a slide show in a message
1 View the message.
1 View the message.
2 Highlight the slide show and press r.
2 Highlight the website URL you want to go
to.
3 To speed up the slide show, press
right or down.
3 Press M > Go To Website.
Note: The entire URL must appear in the
message to allow you to open the
website.
view a slide show
Your handset can receive MMS messages
containing slide shows.
66
main attractions
4 To repeat the part of the slide show you
have just viewed, press
left or up.
5 To view the slide show again, press under Restart.
Tip: You can create and send MMS messages
containing slide shows on
www.telusmobility.com.
save an embedded picture,
video, or audio recording
delete an embedded picture,
video, or audio recording
To save a picture, video, or audio recording
that is part of the body of a message you
receive:
To delete a picture, video, or audio recording
that is part of the body of a message you
receive:
1 View the message.
1 View the message.
2 Highlight the picture, video, or audio
recording you want to save.
3 Press M.
2 Highlight the picture, video, or audio
recording you want to delete and press
M.
4 Select Save Picture, Save Video, or Save Audio.
3 Select Delete Picture, Delete Video, or Delete Audio.
The item will save in the default storage
location.
save attachments
Note: Some types of pictures, videos, and
audio recordings can be viewed or played,
but not saved.
2 Highlight the attachment you want to
save.
1 View the message.
3 Press M > Save Attachment.
main attractions
67
Selected items save to the default storage
location.
save audio
Note: Some types of pictures, videos, and
audio recordings can be viewed or played,
but not saved.
2 Press M > Save Audio.
delete attachments
1 View the message.
2 Highlight the attachment you want to
delete.
3 Press M > Delete Attachment.
4 Press - under Yes to confirm.
save a picture
1 View the slide show.
2 When the picture you want to save
appears, press M > Save Picture.
68
main attractions
1 View the slide show.
If the slide show contains more than one
audio recording, a list of the audio
recordings appears. Select the audio
recording you want to save.
message transmission
After you start to send a message you have
created or start to download a message you
have been sent, you can still stop the
message transmission from being completed:
With the flip is closed, press the smart key on
the top .. Opening or closing the flip does
not interrupt message transmission.
customize MMS
Shortcut: From the home screen press under Msgs > M > MMS Setup.
or
Find it: M > g > M > MMS Setup.
This option is available from many contextsensitive menus when you are using MMS.
The following options become available:
option
Friendly Name: Enter text here to create a
friendly name. Your friendly name is the
name displayed in the From field on other
iDEN handsets when they receive
messages from you.
Signature: Enter text here to create a
signature. Your signature is text that is
automatically inserted at the end of all
messages you create. You can edit the text
before sending the message.
option
Quick Notes: Lets you create new Quick Notes
and edit or delete Quick Notes you have
created.
Replies: Lets you create new reply phrases
and edit or delete reply phrases you have
created.
Download Options: Controls whether your phone
automatically downloads new messages
when they arrive, or only after you respond
to a prompt or read the message from the
Inbox. Set this option to Automatic if you want
your phone to download new messages
automatically; set the option to Manual if you
want your phone to prompt you before
downloading new messages.
Cleanup: Controls how long messages remain
in the Inbox and Outbox before they are
deleted.
main attractions
69
new quick notes and reply
phrases
Note: These Quick Notes are not the same as
the quick notes used with MOSMS
messages. Each messaging service has its
own quick notes feature.
create quick notes
1 From the MMS Setup menu, select Quick
Notes or Replies.
2 Select [New QuickNote] or [New Reply].
3 Enter text from the keypad and press r.
edit quick notes
You can edit only Quick Notes and reply
phrases you have created.
1 From the MMS Setup menu, select Quick
Notes or Replies.
2 Select the Quick Note or reply phrase you
want to edit.
70
main attractions
3 Edit the text and press r.
delete only Quick Notes and reply
phrases you have created
1 From the MMS Setup menu, select Quick
Notes or Replies.
2 Scroll to the Quick Note or reply phrase
you want to delete.
3 Press - under Delete.
4 Press - under Yes to confirm.
delete all Quick Notes or all reply
phrases you have created
1 From the MMS Setup menu, select Quick
Notes or Replies.
2 Press M > Delete All.
3 Press - under Yes to confirm.
cleanup options
The cleanup option controls how long
messages remain in the Inbox and Sent Itmes
before they are deleted. You set the cleanup
option for the Inbox and Outbox separately.
The cleanup option deletes only read,
unlocked messages.
Shortcut: From the home screen press under Msgs > M > MMS Setup > Cleanup.
or
Find it: M > g > M > MMS Setup > Cleanup.
1 Select Inbox or Outbox.
Choose a clean up option from the following
list:
option
Off: Messages are never automatically
deleted.
option
5 Messages: If you have more than 5
messages, messages are deleted in the
order they were received, starting with the
oldest, until 5 are left.
10 Messages: If you have more than 10
messages, messages are deleted in the
order they were received, starting with the
oldest, until 10 are left.
With these options, messages are deleted
in the order they were received, starting
with the oldest, until the selected number
are left.
1 Day: Messages are deleted if they are older
than 1 day.
3 Days: Messages are deleted if they are
older than 3 days.
With these options, messages are deleted
when you exit the message center after
setting the option.
main attractions
71
option
Custom: Lets you create a clean-up option of
up to 99 messages or 99 days. for the inbox
2 Press - under Yes to automatically delete
messages now or press - under No to
delete messages later.
delete all messages
To delete all read, unlocked messages from
the MMS Inbox, all messages in the MMS
drafts folder, or all successfully sent
messages in the MMS Outbox:
1 Press M > g.
2 Select Inbox, Drafts or Outbox.
3 Select MMS Inbox, MMS Drafts, or MMS Outbox.
4 Press M > Delete All.
5 Press - under Yes to confirm.
Mike’s wireless web
services
Your handset is equipped with a
microbrowser that can be used to access
Mike's Wireless Web Services and other upto-the-minute information. You can view
specially designed text versions of popular
Internet sites that provide news, sports,
weather, entertainment, stock quote sites,
and other useful information.
access the microbrowser
The first time you use the microbrowser, you
will be required to go through a security setup
process that takes approximately one to three
minutes. Please follow the on-screen prompts
to complete the security setup process. This
setup process will only occur the first time
you use the service.
Find it: M > 1 > Browser
72
main attractions
1 Once connected, the Homepage (or the
last page visited) will be displayed. To
access the Home menu page from any
other menu in the microbrowser, press
S.
To view additional text while visiting a site,
use the navigation key
to scroll to read
it.
navigate the microbrowser
When you use the microbrowser, some keys
on your handset operate differently than
during a normal phone call. These keys are
explained below:
E
Home key - press to return to the
default Home page (the page
first seen when you launch the
browser). Press and hold for
two seconds to exit the
browser.
*
0
Asterisk/Back key - press to return to
the previous page viewed
before the current page.
0/+ Next key - press after using
the back key to return to the
original page viewed.
access the browser menu
1 Press and hold M to access the browser
menu.
2 Scroll to select the desired option.
3 Press - under Ok to initiate the option.
option
Exit Browser - closes the browser and returns
you to the idle screen. Use this option
when you want to return to the page
currently viewed at a later time, without
navigating through the entire menu
structure again.
main attractions
73
option
Reload - reloads the current Wireless Web
page viewed, refreshing the information
with the most current from the information
provider.
Home - returns you to your default Home
page, the first page you see when launching
the microbrowser.
Bookmarks - allows you to access bookmarks
you have created using the Bookmark
option.
Mark Site - identifies sites you would like to
visit easily and quickly from your
microbrowser.
About Phone.com - contains information about
the version of the Phone.com browser
loaded on your handset.
Advanced Options - helps troubleshoot any
service issues you may have with your
browser.
74
main attractions
customize your microbrowser
You can adjust the size of the display and the
font in your microbrowser.
Find it: M > 1 > Browser > M > Preferences >
Look & Feel.
1 To adjust the size of the display, select
Screen width and check one of the pixel
options.
2 To adjust the size of the font, select Font
Size and check one of the size options.
end the microbrowser session
At any point in the session, press and hold E
for two seconds to exit the microbrowser.
bluetooth®
Your phone supports the use of wireless
Bluetooth stereo headsets. The audio from
the audio player is routed to the stereo
headset. Additionally the handset can be
connected to a Bluetooth Home Stereo
Adapter to stream content from your home
entertainment system and listen wirelessly
from your headset withouth missing a call.
2 Select Name if you wish to assign a name
to your handset.
All stereo audio includes ring tones, music
and Java sound.
Tip: You can turn off Bluetooth if you want to
prolong battery life or if you enter an area
where Bluetooth is prohibited.
Find it: M > m > Bluetooth.
The Bluetooth connection menu contains an
option to search for Audio Devices including
stereo Bluetooth devices.
turn Bluetooth On or Off
You can turn your phone’s Bluetooth feature
on or off. While Bluetooth power is on, your
phone can communicate with other devices.
Find it: M > m > Bluetooth > Setup > Power.
1 Select On to power Bluetooth On.
3 Select Find Me Duration to determine the
amount of time in which your handset can
be found by other Bluetooth devices.
make a Bluetooth connection
connect your phone with a Bluetooth
headset
Find it: M > m > Bluetooth > Audio Devices >
[Look for Devices].
1 Follow the instructions on your Bluetooth
headset to set it up to be found.
2 Once your Bluetooth headset is set to be
found press r on your handset. Your
phone will scan the Bluetooth headset
main attractions
75
until it finds it. Press r when you see
the name of the Bluetooth headset on
your screen.
3 Your phone requires that you create a
bond in order to connect with a Bluetooth
headset. Press - under Yes when you are
prompted to bond with the headset.
4 Enter the Bluetooth pass key.
Some Bluetooth devices ship with
Bluetooth PINs. Please refer to your
Bluetooth device’s user guide to locate
this information.
If a device ships without a Bluetooth PIN,
then you can enter any PIN for that
device. To establish a connection to that
device, enter the same PIN for both your
phone and the device. For example, if you
enter 1234 as the device’s PIN, then enter
1234 as your phone’s PIN.
5 Press - under Ok.
76
main attractions
Note: This model offers bluetooth auto pair
feature with auto pair compatible Motorola
devices. When bonded via bluetooth with a
certain device, the pin will not be required.
connect your phone with another
device using Bluetooth
Find it: M > m > Bluetooth > Pair To Devices.
1 Select the device you want from the list of
found devices on your screen.
2 Create a bond if you are prompted to do
so.
Tip: If you have previously connected to a
device, the device will be stored on your
phone so you can connect with it easily.
use Bluetooth during a call
You can connect with available Bluetooth
devices during a call.
Note: If the Audio Devices list contains only one
device, then your phone will automatically try
to connect to that device.
send Contacts
Shortcut: From the home screen press under Contcs.
1 While in a call, press M > Use Bluetooth.
1 Select the contact you want to send.
2 Press - under Yes to power On
Bluetooth.
2 Press M > Send Via... > Bluetooth.
3 Select the audio device you want to
connect to from the list of Handsfree Devices.
send information via Bluetooth
You can use your phone to send Contacts
entries, Datebook events, or audio files,
pictures, and videos in the media center to
another Bluetooth device.
The receiving device must be within 32 feet
(10 meters) of your phone in order to connect
with yours.
Note: Files sent or received may be up to
6 MB.
3 Press - under Yes to power On
Bluetooth.
4 Select the device you want to transfer the
contact information to.
or
Search for the device by selecting [Look for
Devices].
5 If prompted, bond with the device.
Your phone connects with the devices and
transfers the contact.
send a Datebook event
Find it: M > m > Datebook
main attractions
77
1 Select the datebook event you want to
send.
2 Press M > Send Via... > Bluetooth.
If the event you select repeats, then you
will be prompted to choose whether to
send the selected instance of the event or
all instances of the event.
To send only the selected instance of the
event, select This Event Only.
or
To send all instances of the event, select
Repeat Events.
3 Press - under Yes to power On
Bluetooth.
4 Select the device you want to transfer the
contact information to.
or
78
Search for the device by selecting [Look for
Devices].
5 If prompted, bond with the device.
Your phone connects with the device and
sends the datebook event.
send audio files, pictures, and videos
Note: Note: You can only send audio files,
pictures, and videos if they are not forward
locked and if their DRM settings do not
prevent you from sending.
Find it: M > j > Media Center
1 Select the audio file, picture, or video you
want to send.
2 Press M > Send Via... > Bluetooth.
3 Select the device you want to transfer the
contact information to.
or
main attractions
Search for the device by selecting [Look for
Devices].
4 If prompted, bond with the device.
Your phone connects with the device and
sends the datebook event.
clock screen saver
Your phone comes with a clock screen saver
that shows the time and day of the month
through the external display when the phone
is in power save mode.
When a key is pressed the screen saver is
removed and the display lights up.
Find it: M > u > Display/Info > Clock > Screen
Saver.
You can choose from five different clock
styles:
External Clock 1
External Clock 3
External Clock 2
12
2:11pm
3
9
21
21
6
External Clock 4
External Clock 5
12
21
3
9
21
6
main attractions
79
basics
See page 1 for a basic phone diagram.
status indicators
display
Status indicators are shown at the top of the
home screen:
The home screen shows when you turn on
the phone. To dial a number from the home
screen, press number keys and N.
1. 2. 3. 4.
5. 6. 7.
TELUS
4/25/07
Note: Your home screen may look different.
04
05 pm
Date
TELUS
4/25/07
Contcs
04
Time
05 pm
Left Soft
Key Label
Right Soft
Key Label
Soft key labels show the current soft key
functions. For soft key locations, see page 1.
80
basics
Msgs
1 Signal Strength Indicator: Vertical bars
show the strength of the network
connection. You can’t make or receive
calls when 1 or 0 shows.
2 Active Phone Line: 1 indicates phone line
1 is ready to make calls; 2 indicates phone
line 2 is ready to make calls.
3 Speaker On/Off: Sounds associated with
Private calls and group calls can be set to
come through the earpiece rather than
through the speaker.
main menu
All your phone’s features can be accessed
through the main menu. You can set the main
menu to appear as List View, Icon View, or as Tab
View.
Find it: M > u > Display/Info > Menu View.
4 Ringer Vibe/On: Your phone is set to not
ring.
text entry
5 Message Indicator: Shows when you
receive a text message.
Some features let you enter text.
6 Packet Data: Your handset is ready to
transfer packet data or is transferring
packet data when it shows a blinking
arrow.
7 Battery Charge Indicator: A fuller battery
indicates a greater charge. Recharge the
battery when your phone shows Low Battery.
Your phone provides convenient ways to enter
words, letters, punctuation, and numbers
whenever you are prompted to enter text (for
example, when adding a Contacts entry or
when using Text Messaging).
change the character input mode
1 When you see a screen where you can
enter text, press M to change the
character input method.
basics
81
2 Select one of the following options:
entry modes
Alpha
Press a key several times for
different characters.
Word
Enter words using a predictive
text entering system that lets
you enter a word with fewer
keypresses.
Symbols
Enter symbols.
Numeric
Enter numbers by pressing the
numbers on the keypad.
Language Select the language in which you
want to write the text.
Tip: When entering text, press * to
display the text counter. The maximum
letters you can type on one message depends
on the language. The i877 supports up to 765
letters in English. If your carrier provides long
82
basics
text message service such as concatenated
SMS, the page counter is also displayed.
word method
The Word English text input method lets you
enter text into your phone by pressing keys
just once per letter.
The Word English text input method
combines the groups of letters found on each
phone key with a fast-access dictionary of
words, and recognizes what you want to text
as you type. It first offers the most commonlyused word for the key sequence you enter
and lets you access other choices with one or
more presses of the 0 key.
enter a word using ”word” method
character input
1 Select the Word character input method.
2 Press the corresponding keys once per
letter to enter a word (for example, to
enter the word Bill, press 2 4 5 5).
(If you make a mistake, press * to erase
a single character. Press and hold * to
delete an entire entry.)
3 To accept a word and insert a space,
press #.
To accept a word completion (such as
Billion when you entered Bill), press
right.
If you get a word you don’t want, you can
press the 0 key to see more word
choices and pick the one you want.
alpha method
To enter characters by tapping the keypad:
1 Select the Alpha mode.
2 Press the corresponding keys repeatedly
until the desired letter appears. (For
example, to enter the word Bill, press 2
twice, 4 three times, 5 three times,
and 5 three times again. If you make a
mistake, press Delete to erase a single
character. Press and hold Delete to erase an
entire word.)
By default, the first letter of an entry is
capitalized and the following letters are
lowercased. After a character is entered, the
cursor automatically advances to the next
space after two seconds or when you enter a
character on a different key.
Characters scroll in the following order:
characters
1
.?!,@&:;“-()‘¿ ¡%£ $¥
2
ABC2ÁÃÂÀÇ
3
DEF3ÉÊÈ
4
GHI4ÍÌ
5
JKL5
6
MNO6ÓÕÔÒ
7
PQRS7ß
basics
83
characters
8
TUV8ÚÜÛÙ
9
WXYZ9
0
+-0*/\[]=><#§
#
Space
*
Back
handsfree speaker
You can use your phone’s handsfree speaker
to make calls without holding the phone to
your ear.
During a call (with the flip open), press under Speaker to turn the handsfree speaker
On.
navigation key
The handsfree speaker stays on until you
press - under Speaker or close the flip.
Press the navigation key
up, down, left, or right
to scroll to items in the
display. When you scroll
to highlight the desired
item, press r.
Note: The handsfree speaker won’t work
when your phone is connected to a handsfree
car kit or headset.
84
basics
codes & passwords
lock & unlock phone
The Security menu lets you turn security
features on and off and change passwords.
See “security” on page 112.
Phone Lock - Turns on a feature that locks your
phone: Lock Now takes effect immediately; Auto
Lock takes effect when your phone is powered
off and then on. An unlock code is required to
enable this feature, to unlock the phone, and
to set a new unlock code. Contact your
service provider for your default unlock code.
option
SIM PIN - Enables and disables your phone’s
SIM PIN security feature.
GPS PIN - Enables and disables your phone’s
GPS PIN security feature.
Change Passwords - Changes your phone unlock
code, security code, SIM PIN, and GPS PIN.
Keypad Lock - Locks the phone’s keypad, either
immediately or automatically after a set period
of inactivity.
Note: You can make emergency calls on a
locked phone (see page 99). A locked phone
still rings or vibrates for incoming calls or
messages, but you need to unlock it to
answer.
basics
85
transmitters
Note: Consult airline staff about the use of
the Transmitters Off feature during flight. Turn
off your phone whenever instructed to do so
by airline staff.
Transmitters Off mode turns off your phone’s
calling features in situations where wireless
phone use is prohibited, but you can use the
phone’s other non-calling features when
transmitters is turned Off.
Find it: M > u > Advanced > Transmitters > Off.
use GPS with map
software
Your phone is enabled with a highly-capable
GPS receiver that sends location information
to a USB port on a PC, laptop, or PDA.
86
basics
Note: No serial port connectivity is provided
by your phone. Applications on the host
device which are expecting to receive the
GPS location information via a serial port must
instead use a Virtual Serial Comm Port.
The data sent to the host device is formatted
as prescribed in the National Marine
Electronics Association 0183 V3.0 (NMEA0183) standard. As such it supports the
following sentences: GGA, GLL, GSA, GSV,
RMC, and VTG.
This handset is not a full NMEA-0183
compliant device supporting electrical RS-422/
RS-232 connectivity as dictated by the NMEA0183 standard. Consequently it's unsuitable
for conventional marine NMEA-0183
equipment use. Its intended use is for normal
"terrestrial" mobile users who want to enable
their USB hosting computing devices such as
a PC, laptop or PDA with the phone's highlycapable GPS functionality.
get connected
• Stop bits: 1
1 Slide open the phone's bottom
connector and insert a mini-USB cable
into the phone's bottom connector.
• Flow control: None.
2 Insert the other end of the mini-USB cable
into a vacant USB receptacle of your host
device. A virtual USB Comm Port will be
created on your host device upon
successful enumeration of the phone as a
USB Communications Device Class
device.
3 Ensure no application in your host device
is using the created COMM port. You
may need to ensure that the created
virtual COMM port settings are set as
follows:
• Bits per second: 4800
• Data bits: 8
• Parity: None
4 Start the GPS application on your host
device. Set the GPS application to start
accepting NMEA-0183 formatted data
from the created Virtual COMM port.
5 Set your phone to start sending NMEA0183 formatted location information.
Find it: M > m > GPS > Interface > NMEA OUT >
USB.
Your phone is now actively sending location
NMEA-0183 formatted GPS data to your USB
host device.
To stop your phone from sending location
data:
Find it: M > m > GPS > Interface > NMEA OUT >
Off.
Note: Each time you power your phone Off,
NMEA OUT is automatically set to Off and
basics
87
you need to manually restart it using the
menu selections above.
Your USB host device will generally provide
charging power (5V, up to 500mA) to your
phone via the mini-USB cable therefore no
other charging power to it will normally be
required. However some laptops may require
that you provide external AC/DC power to the
laptop in order for it to provide full 500mA
charging current capability to the phone.
optimize your handset position and
orientation
While in a phone call slide your phone up and
down, then left and right until best
microphone coupling is obtained. You also
may need to adjust your hearing aid (HA)
volume setting.
features for the hearing
impaired
using your phone with a
hearing aid
For best results use the following optimization
procedures and handset setting. They
generally apply as well for users with cochlear
implants:
88
basics
If your HA has a telecoil, activate its switch,
then also rotate the handset as illustrated to
align the telecoils.
Note: Some automatically switched hearing
aids may need an auxiliary switching magnet.
If you are unsure whether your HA is telecoil
equipped or needs an auxiliary magnet,
please refer to your HA user guide or contact
a hearing aid professional or supplier.
Approximate telecoil location is within
6-13 mm of this location.
Off - Shut off
M - Microphone
T - Telecoil
Approximate telecoil location is just
above the battery.
optimize your handset antenna
position
Your phone’s rating for HA compatibility is
determined with the antenna extended if it
has an extendable antenna. However,
acceptable use might occur with the antenna
retracted. Test your handset in both antenna
positions when the handset is in the optimum
orientation.
choose your hearing aid setting
Find it: M > Settings > Phone Calls > Hearing Aid.
1 Set this option to Microphone. Microphone
coupling is now optimized.
or
2 Set this option to Telecoil. Handset meets
US federal requirements for telecoil
coupling sound.
or
3 Set this option to Off (factory default). This
is the setting for non HA users.
basics
89
features for the vision
impaired
voice playback
The Voice Playback feature allows you to use a
simulated voice to guide you through phone
menus and through placing and receiving
phone calls.
You can hear the following as you use your
phone:
• The number keys you have pressed
• The names, numbers, and contact
types of each contact entry as you
scroll through Contacts
• The status information on the Home
screen, such as signal strength, battery
level, date and time, and service status
90
basics
Note: When you access the home
screen, you will hear “Home”
• Main menu options as you scroll
through the main menu
• A prompt indicating that your phone is
placing a call
• The name of incoming callers rather
than a ring tone
Find it: M > u > Voice Playback.
1 Select Speak Text > On for the navigation
playback.
2 Select Speak Caller > On to hear the name or
phone number of incoming callers
3 Select Voice and choose either a female
voice (Barbara) or male voice (Simon).
4 Select Multimedia Volume and press the
volume keys up or down to adjust the
volume of voice playback.
high contrast theme
Your phone comes with a standard high
contrast theme that provides black and white
text with reverse text highlighting and very
large icons for easy visualization of selection.
Find it: M > u > Display/Info > Theme > High
Contrast.
basics
91
customize
volume
Press the volume
keys to:
• turn off an
incoming call alert
• change the
earpiece volume during calls
• change the ringer volume from the
home screen
ring tones
To set the ring tone your phone makes when
you receive phone calls, call alerts, message
notifications, pictures sent using Send via PTT
or Datebook reminders:
92
customize
Note: Only ring tones stored in your phone’s
memory are available in the ring tones list. To
assign a ring tone stored on a memory card
inserted in your phone’s memory card slot,
you must go to the media center. Ring tones
purchased or received from TELUS can be
assigned as ring tones. Other audio files may
not be supported as ring tones.
Find it: M > j > Ring Tones
1 Make sure Vibrate All is set to Off.
2 Scroll through the list of ring tones and
select the one you want to assign. Vibrate
sets your phone to vibrate instead of
making a sound; Silent sets your phone to
neither vibrate nor make a sound.
Tip: Highlighting a ring tone lets you hear it.
3 Select the features you want to assign the
ring tone to.
4 When you are finished, press - under
Done.
Note: This icon M appears on the display if
you set your phone to neither vibrate nor
make a sound for phone calls.
setting your phone to vibrate
You can set your phone to vibrate instead of
making a sound when you receive all phone
calls, Private calls, group calls, call alerts,
messages notifications, pictures sent using
Send via PTT, and Datebook reminders.
Find it: M > j > Ring Tones > Vibrate All > On.
2 Select Vibrate from the list of ring tones.
3 Select the features you want to set to
make no sound.
4 When you are finished, press - under
Done.
wallpaper
Set a previously saved photo or picture as a
wallpaper (background) image in your phone’s
external display, internal screen or throughout
all menu screens.
Find it: M > u > Display/Info > Wallpaper.
1 Select External
To set your phone to vibrate instead of making
a sound for some features but not others:
2 Scroll through the list of pictures and
press r to select the picture of your
choice.
Find it: M > j > Ring Tones.
3 Press - under Back.
1 Make sure Vibrate All is set to Off.
4 Select Internal > Placement
customize
93
If you want the wallpaper in the home
screen only select Idle Only; if you want the
wallpaper to show throughout all the
menu screen, select Throughout.
Note: You can set the internal and external
wallpapers to change automatically after a
certain period of time by turning on the Auto
Cycle feature located in the Wallpaper menu. If
you set this feature to On, you can choose the
pictures you want to appear randomly.
datebook
Find it: M > m > Datebook > M > Setup.
You can view or change these options:
Start View - Sets Datebook to start in day view,
week view, or month view when you access
Datebook.
Daily Begin - Sets the beginning of your day. This
is the earliest time of day displayed in week
view, if you have a 12-hour day view.
Delete After - Sets the amount of time Datebook
waits to delete an event after it occurs.
Time Shift - Lets you shift the times of all
Datebook events. This is useful if you are
traveling to a different time zone.
Alert Timeout - Sets the amount of time a tone
continues to sound when you receive a
Datebook reminder.
Clock - Controls whether the time and date
appear on the home screen; sets time and
date format; sets year.
hide or show
location information
Your phone is equipped with a Location
feature for use in connection with location-
94
customize
based services that may be available in the
future.
The Location feature allows the network to
detect your position. Turning Location off will
hide your location from everyone except 911.
Note: Turning Location on will allow the
network to detect your position using GPS
technology, making some applications and
services easier to use. Turning Location off
will disable the GPS location function for all
purposes except 911, but will not hide your
general location based on the cell site serving
your call. No application or service may use
your location without your request or
permission. GPS-enhanced 911 is not
available in all areas.
Select from the following options:
option
Restricted: No Java or similar software
applications may view the location of your
phone. However, location information may
still be available to the phone’s owner, fleet
manager, or account administrator.
Unrestricted: All applications may view the
location of your phone, without notifying
you.
By Permission: When an application attempts
to view the location of your phone, you will
be prompted to give permission. However,
location information may still be available to
the phone’s owner, fleet manager, or
account administrator.
set your privacy options
Find it: M > m > GPS > Privacy.
customize
95
calls
To make and answer calls, see page 19.
• short text messages received
• pictures sent or received
turn off a call alert
You can press the volume keys to turn off a
call alert before answering the call.
recent calls
The recent calls list contains information
associated with calls you have made and
received and call alerts you have received.
When you send or receive Private calls, the
recent call list contains the following PTV
items with those calls:
• contact information received
• My Info received
96
calls
• Datebook events received
• Location information received
The recent calls list displays up to 20 of the
most recent calls and call alerts.
1 Press M > Recent Calls.
2 Scroll through the list.
store an item to contacts from
recent calls
Phone calls, Private calls, My Info, Contacts or
Location entries received from other phones
can be stored to the Contacts list from the
Recent Calls list.
Find it: M > Recent Calls.
1 Scroll to or select the item you want to
store.
2 Press - under Save to store the
information as a new entry in the
Contacts list.
or
3 Select an existing contact and update the
information.
4 Press - under Save to save your changes.
redial
To redial your last outgoing call, press and
hold N or push the PTT button if it was a
private call.
caller ID
Caller ID allows people to identify a caller
before answering the phone by displaying the
number of the incoming call. If you do not
want your number displayed when you make
a call, just follow these easy steps.
To block your phone number from being
displayed for a specific outgoing call:
1 Press * 6 7.
2 Enter the number you want to call.
3 Press N.
To permanently block your number, call your
TELUS Client Care.
call forward
Call forwarding sends calls to the phone
numbers you specify. You can forward all calls
to one number or forward missed calls to
calls
97
different numbers depending on the reason
you missed the call. You can forward phone
lines 1 and 2 independently.
Find it: M > u > Phone Calls > Call Forward.
1 To forward all calls select All Calls and select
To to enter the phone number you want all
your calls forwarded to.
or
2 You can specify a forwarding number for
each type of missed call by selecting
Detailed and chosing the following options:
voice name
You can place calls by speaking comands to
your phone if you have previously assigned a
voice name to your contacts.
assign voice names to contacs
1 Press - under Contcs and select [New
Contact].
If Busy: When your handset is on a call or
transferring data.
2 Assign a name, phone number and select
[Options].
If No Answer: When you do not answer on
the first 4 rings.
3 Select Voice Name and follow the propmt to
record the voice name.
If Unreachable: When your handset is out of
coverage or powered off.
4 Press - under Back and - under Save.
Note: Your handset comes pre-programmed
to detailed forward to Mike’s Voice Mail. If you
98
change your detailed call forwarding,
remember to reset the forwarding back to
your access number or your phone number.
calls
place a call using voice name
1 With the flip closed or open, press the
speaker key t until you are prompted to
say the voice name.
Your phone supports emergency calling.
Emergency phone calls can be made even
when your SIM card is blocked or not in your
phone.
The handset will automatically place the call.
Dial 911 or your local emergency number to
be connected to an emergency response
center. If you are on an active call, you must
end it before making an emergency call.
emergency calls
Your service provider programs one or more
emergency phone numbers that you can call
under any circumstances, even when your
phone is locked or the SIM card is not
inserted.
Note: Emergency numbers vary by country.
Your phone’s preprogrammed emergency
number(s) may not work in all locations, and
sometimes an emergency call cannot be
placed due to network, environmental, or
interference issues.
When you make an emergency call, your
phone’s GPS Enabled feature can help
emergency service personnel find you, if you
are in a location where your phone's GPS
antenna has established a clear view of the
open sky and your local emergency response
center has the equipment to process location
information. Because of the limitations of this
feature, always provide your best knowledge
of your location to the emergency response
center when you make an emergency call.
Note: Emergency calls cannot be placed
while the keypad is locked.
calls
99
Note: If you have not registered on the
network, emergency calls cannot be placed
while your SIM card is in your phone.
international calls
If your phone service includes international
dialing, press and hold 0 to insert your local
international access code (indicated by +).
Then, press the keypad keys to dial the
country code and phone number.
speed dial
Each phone number stored in Contacts is
assigned a Speed Dial number, which you can
use to call that number.
1 From the home screen, use the keypad to
enter the Speed Dial number assigned to
the phone number you want to call.
2 Press #.
100
calls
3 Press N.
turbo dial
The first nine entries in your contacts are set
for turbo dial. They can be called by pressing
and holding the speed dial number
(1 through 9).
voicemail
receive a message
When you receive a voice mail message, New
VoiceMail Message appears on the display.
• To call TELUS voice mail system and
listen to the message, press - under
Call.
• To dismiss the message notification:
If the flip is closed, press the smart key
. on the top.
If the flip is open, press r, and press
- under Back, or close the flip.
If the caller leaves a message, this icon y
appears on the display, reminding you that
you have a new message.
advanced voice mail with fax
Mike's Advanced Voice Mail with Fax allows
you to receive faxes directly to your handset
and store them along with your voice
messages until you are ready to print. Follow
the voice mail prompts to print the fax to a fax
machine. It ensures privacy, convenience and
eliminates the need for a separate fax line.
When you subscribe to Mike's
Advanced Voice Mail with Fax, you will
receive a fax number from your point of
feature activation. If you have not received a
fax number, please contact the nearest
TELUS dealer or call TELUS client care.
Please see www.telusmobility.com for
more details of TELUS Voice Messaging
services.
fax mail Indicator
Your handset is equipped with a Fax Mail
indicator to notify you when you have
received a fax through Mike's Advanced Voice
Mail with Fax.
Shortcut: From the home screen press under Msgs > Fax Mail.
When you receive a new fax, New FaxMail
Message appears on the display.
Your handset will alert you audibly until you
press - under Call or - under Exit.
calls
101
net alerts
When you receive a Net Alert, a notification
appears on the display.
If you dismiss the notification, this icon w
appears on the display, reminding you that
you have a new message.
102
calls
other features
advanced calling
feature
call waiting
To accept the second call
and put the active call on
hold press - under Yes.
To accept the second call
and end the active call press
O.
Your phone rings with the
second call for you to
answer.
feature
3-way call
Make or receive a phone call
and press M > 3 Way. Enter
the second phone number,
press N and - under Join.
Tip: For quick ways to enter
the number, press M to
see the dialing menu.
You cannot make any other
calls after you have joined a
3-way call, even if one party
disconnects.
other features—advanced calling
103
feature
flip
activation
any key
answer
alarm clock
To make your handset to
answer and end calls by
opening and closing the flip
press M > u > Phone Calls
> Flip Activation.
Select Flip To Ans > On and Flip
to End > On.
To answer phone calls by
pressing any key on the
keypad press M > u >
Phone Calls > Any Key Ans > On.
feature
access
alarm clock
stop watch
quick timer
To access the alarm clock
press M > T > Alarm Clock
Plus
To set the alarm clock press
- under Set. Use
to set
the desired time and press
- under Done
To access the stop watch
press M > T > Alarm Clock
Plus > M > Stopwatch
Press - under Start
To access the quick timer
press M > T > Alarm Clock
Plus > M > Quick Timer
Use
to set the desired
time and press - under
Start
104
other features—alarm clock
feature
do not
disturb
contacts
To access Do not disturb
press M > T > Alarm Clock
Plus > M > Do Not Disturb.
Press - under Yes.
“Do Not Disturb”mode will
allow you to turn off your
phone’s transmitters. When
your phone is set to Do Not
Disturb, no incoming phone or
private calls will be received.
feature
edit/delete
contact
entry
Press - under Contacts.
Select a contact and press
M > Edit. Change the
desired content and press
- under Save.
set ringer ID Press - under Contacts.
Select a contact and press
M > Edit > [Ring Tone/Picture].
Note: Alarm Clock features only work when
the handset is powered On.
Warning: When you set the alarm clock,
"default subject" data is stored in your
datebook. This data is neccessary for the
alarm clock to work properly; do not delete
this data from the datebook.
set picture
ID
Select desired ringer and
press - under Back > under Save
Press - under Contacts.
Select a contact and press
M > Edit > [Ring Tone/Picture].
Select desired picture and
press - under Back > under Save
other features—contacts
105
datebook
feature
create
datebook
events
see datebook
event
event
reminder
To create a new Datebook
event press M > m >
Datebook > [New Event].
To see a calendar event
press M > m > Datebook.
Press
left or right to see
the day and
up or down
to see the events.
When an event reminder
occurs press - under View.
Press - under Back to close
the reminder.
106
other features—datebook
feature
receive
datebook
events via
PTT
To view the information
while still in the Private call
press r.
The 5 most recent events
received from a Private ID
are stored with the that
Private ID on the recent calls
list.
To store events to the
Datebook press - under
Save while viewing the event
you want to store.
GPS
Note: To improve GPS performance:
• Stay in the open,
• Extend your phone's antenna
feature
view
To see your aproximate
approximate location press M > u >
location
GPS > Position. Scroll to view
the entire screen.
• Move away from other electrical or
electronic devices
• Remain stationary.
• Avoid touching the antenna with your
hands.
feature
make an
emergency
call
Dial your local emergency
number to be connected to
an emergency response
center. If you are on an
active call, you must end it
before making an
emergency call.
set GPS
privacy
options
To recalculate position press
Refresh. This may take several
minutes.
To set the level of privacy for
your GPS system press M
> u > GPS > Privacy.
If your GPS PIN security
feature is enabled, enter
your GPS PIN and select the
privacy option you want.
other features—GPS
107
feature
set GPS PIN To set up a PIN to access
security
your GPS press M > u >
Security > GPS PIN. Select On
and enter the current GPS
PIN.
Note: When you receive
your phone, your GPS PIN is
0000.
To change your GPS PIN
press M > u > Security >
Change Passwords > GPS PIN.
Enter the current GPS PIN
and enter the new 4- to 8digit GPS PIN. Re-enter the
new 4- to 8-digit GPS PIN to
confirm.
108
other features—handsfree
handsfree
Note: The use of wireless phones while
driving may cause distraction. Discontinue a
call if you can't concentrate on driving.
Additionally, the use of wireless devices and
their accessories may be prohibited or
restricted in certain areas. Always obey the
laws and regulations on the use of these
products.
feature
speakerphone
Activate the speakerphone
while driving:
Press and hold the
speakerphone key or press
- under Options > Speaker.
feature
auto
answer
memory card
To automatically answer
calls when connected to a
car kit or headset press M
> u > Phone Calls > Auto Ans.
Select the amount of rings
before answering.
feature
change
storage
preferences
To choose whether media
items are saved to your
phone's memory or to the
memory card press M >
u > Memory Card > Store Media
> On Phone or Prefer On Card.
Note: If the memory card is
not in the phone, even if you
choose Prefer On Card, the
media items are saved to
your phone's memory.
other features—memory card
109
feature
manage
memory
messages
To view your used memory,
free memory, memory
capacity, and number of files
in phone memory press M
> j > Media Center > M >
Memory Usage.
To free memory on your
phone, delete items from
the media center, voice
records, or Java
applications. To free
memory on the memory
card, delete items from the
card's folders.
feature
read
messages
reply to
messages
When you receive a
text message, it will
automatically appear on your
phone's main display
screen. To view the entire
message press
down. If
the messages is urgent, the
message icon blinks in your
display.
While the message is
open press - under
Reply. Type message and
press - under Send.
or
Press - under Reply. Select
a quick message and press
- under Send
110
other features—messages
pc applications
feature
other PC
For a list of complete PC
applications applications visit
www.motorola.com/iden
personalize
feature
language
backlight
time length
menu style
clock
display
To change language, press
M > u > Display/Info >
Language
To select how long the
display screen and keypad
are backlit, press M > u >
Display/Info > Backlight
To show the main menu as
tabs, graphic icons or a textbased list, press M > u >
Display/Info > Menu View
Press M > u > Display/Info
> Clock > Display > On
other features—pc applications
111
TTY
security
feature
turn On TTY From the home screen
feature
press M > u > Phone Calls
> TTY > Use TTY > On.
choose TTY From the home screen
mode
press M > u > Phone Calls
> TTY > Type.
change the
TTY baud
rate
Select from TTY, VCO or HCO.
From the home screen
press M > u > Phone Calls
> TTY > Baud.
Select 45.45 or 50.00
change TTY While in the TTY call, press
mode
M > In Call Setup > TTY > Type.
during a call Select from TTY, VCO or HCO.
feature
phone lock
keypad lock
enable SIM
PIN
change SIM
PIN
To lock the phone press M
> u > Security > Phone Lock >
Lock Now or Auto Lock.
To lock the keypad press M
> u > Security > Keypad Lock >
Lock Now or Auto Lock
Shortcut: To lock the
keypad press M > *
To enable SIM PIN, press
M > u > Security > SIM PIN >
On.
To change the SIM PIN,
press M > u > Security >
Change Passwords > SIM PIN.
Note: You can make emergency calls on a
locked phone (see page 99). A locked phone
112
other features—TTY
still rings or vibrates for incoming calls or
messages, but you need to unlock it to
answer.
other features—security
113
114
other features—security
Important Safety and
Legal Information
115
Safety and General Information
This section contains important information on the safe and
efficient operation of your phone. Read this information
before using your integrated multi-service portable radio.*
Safety Information
Exposure to Radio Frequency (RF)
Energy
Your phone contains a transmitter and receiver. When it is ON, it
receives and transmits RF energy. When you communicate with
your phone, the system handling your call controls the power level
at which your phone transmits.
Your Motorola phone is designed to comply with local regulatory
requirements in your country concerning exposure of human beings
to RF energy.
Portable Radio Product Operation and
EME Exposure
Your Motorola radio product is designed to comply with the
following national and international standards and guidelines
regarding exposure of human beings to radio frequency
electromagnetic energy (EME):
116
Safety Information
• United States Federal Communications Commission, Code
of Federal Regulations; 47 CFR part 2 sub-part J.
• American National Standards Institute (ANSI) / Institute of
Electrical and Electronics Engineers (IEEE). C95. 1-1992.
• Institute of Electrical and Electronics Engineers (IEEE).
C95. 1-2005 Edition.*
• International Commission on Non-Ionizing Radiation
Protection (ICNIRP) 1998.
• Ministry of Health (Canada). Safety Code 6. Limits of
Human Exposure to Radio frequency Electromagnetic
Fields in the Frequency Range from 3 kHz to 300 GHz,
1999.
• Australian Communications Authority Radio
communications (Electromagnetic Radiation - Human
Exposure) Standard 2003.
• ANATEL, Brazil Regulatory Authority, Resolution 303 (July
2, 2002) "Regulation of the limitation of exposure to
* The information provided in this document supersedes
the general safety information in user’s guides
published prior to May 1, 2006
electrical, magnetic, and electromagnetic fields in the
radio frequency range between 9 kHz and 300 GHz."
"Attachment to Resolution 303 from July 2, 2002."
Operational Precautions
To assure optimal radio product performance and to be sure that
human exposure to RF does not exceed the guidelines set forth in
the relevant standards, always follow these instructions and
precautions:
Phone Operation
When placing or receiving a phone call, hold your radio product as
you would a wireline telephone. Speak directly into the
microphone.
Two-way radio operation
Your radio product has been designed and tested to comply with
national and international standards and guidelines regarding
human exposure to RF electromagnetic energy, when operated in
the two-way mode (at the face, or at the abdomen when using an
audio accessory) at usage factors of up to 50% talk/50% listen.
Transmit no more than the rated duty factor of 50% of the time. To
transmit (talk), push the PTT button. To receive calls, release the
PTT button. Transmitting 50% of the time or less, is important
because this radio generates measurable RF energy only when
transmitting (in terms of measuring for standards compliance).
When using your radio product as a traditional
two-way radio, hold the radio product in a
vertical position with the microphone one
to two inches (2.5 to 5 cm) away from the
lips.
If you wear a radio product on your body when
transmitting, always place the radio product in a Motorola
approved clip, holder, holster, case or body harness. If you do not
use a body-worn accessory supplied or approved by Motorola and
are not using the radio product in the intended use positions along
side the head in the phone mode or in front of the face in the
two-way radio mode, or if you hang your device from a lanyard
around your neck, keep the device at least 2.5 centimeters (1 inch)
from your body when transmitting.
Approved Accessories
For a list of approved Motorola accessories call 1-800-453-0920, or
visit our website at www.motorola.com/iden.
RF Energy Interference/Compatibility
Nearly every electronic device is subject to RF energy interference
from external sources if inadequately shielded, designed or
otherwise configured for RF energy compatibility. In some
circumstances your handset may cause interference with other
devices.
Safety Information
117
Follow Instructions to Avoid Interference
Problems
your wireless phone with your implantable medical device, consult
your health care provider.
Turn OFF your radio product where posted notices instruct you to
do so.
In an aircraft, turn off your radio product whenever instructed to do
so by airline staff. If your radio product offers an airplane mode or
similar feature, consult airline staff about using it in flight.
Hearing Aids
Implantable Medical Devices
If you have an implantable medical devices, such as a pacemaker
or defibrillator, consult your physician before using this radio
product.
Persons with implantable medical devices should observe the
following precautions:
• ALWAYS keep the phone more than 20 centimeters (8
inches) from the implantable medical device when the
phone is turned ON.
• DO NOT carry the phone in a breast pocket;
• Use the ear opposite the implantable medical device to
minimize the potential for interference.
• Turn OFF the phone immediately if you have any reason to
suspect that the interference is taking place.
Read and follow the directions from the manufacturer of your
implantable medical device. If you have any questions about using
118
Safety Information
Some phones may interfere with some hearing aids. In the event of
such interference, you may want to consult your hearing aid
manufacturer or physician to discuss alternatives.
Other Medical Devices and Health Care Facilities
If you use any other personal medical devices, consult your
physician or the manufacturer or your device to determine if it is
adequately shielded from RF energy. Turn off your radio product
when instructed to do so in hospitals or health care facilities that
may be using equipment that is sensitive to external RF energy.
Driving Precautions
Check the laws and regulations on the use of radio products in the
area where you drive. Always obey them.
When using your radio product while driving, please:
• Give full attention to driving and to the road. Using a
phone may be distracting. Discontinue a call if you can’t
concentrate on driving.
• Use hands free operation, if available.
• Pull off the road and park before making or answering a
call if driving conditions so require.
• Do not place a handset in the airbag deployment area.
Responsible driving practices can be found in the “Smart Practices
While Driving” section at the end of this guide and/or at the
Motorola Web site: www.motorola.com/callsmart.
Note: The use of wireless phones while driving may cause
distraction. Discontinue a call if you can’t concentrate on driving.
Additionally, the use of wireless devices and their accessories may
be prohibited or restricted in certain areas. Always obey the laws
and regulations on the use of these products.
Operational Warnings
Batteries and Chargers
Caution: Improper treatment or use of batteries may present
a danger of fire, explosion, leakage, or other hazard. For
more information, see the “Battery Use and Battery Safety”
section in this user’s guide.
Your battery, charger, or portable radio may contain symbols,
defined as follows:
Symbol
032374o
Obey all posted signs when using phones in public areas.
032376o
Potentially Explosive Atmospheres
Areas with potentially explosive atmospheres are often but not
always posted, and can include fueling areas such as below decks
on boats, fuel or chemical transfer or storage facilities, or areas
where the air contains chemicals or particles, such as grain, dust
or metal powders.
When you are in such area, turn off your handset, and do not
remove, install, or charge batteries unless it is a radio product type
especially qualified for use in such areas as “Intrinsically Safe” (for
example, Factory Mutual, CSA, or UL approved). In such areas,
sparks can occur and cause an explosion or fire.
032375o
Definition
Important safety information
follows.
Do not dispose of your battery
or phone in a fire.
Your battery or phone may
require recycling in
accordance with local laws.
Contact your local regulatory
authorities for more
information.
Do not throw your battery or
phone in the trash.
Li Ion BATT
032378o
Your phone contains an
internal lithium ion battery.
Safety Information
119
Symbol
Definition
Do not let your battery,
charger, or phone get wet.
Listening at full volume to
music or voice through a
headset may damage your
hearing.
Choking Hazards
Your portable radio or its accessories may include detachable
parts, which may present a choking hazard to small children. Keep
your device and its accessories away from small children.
If you have experienced seizures or blackouts, or if you have a
family history of such occurrences, please consult with your
physician before playing video games or enabling a flashing-lights
feature (if available) on your phone.
Discontinue use and consult a physician if any of the following
symptoms occur: convulsion, eye or muscle twitching, loss of
awareness, involuntary movements, or disorientation. It is always
a good idea to hold the screen away from your eyes, leave the
lights on in the room, take a 15-minute break every hour, and stop
use if you are very tired.
Caution About High Volume Usage
Listening at full volume to music or voice through a
headset may damage your hearing.
Glass Parts
Some parts of your phone may be made of glass. This glass could
break if the product is dropped on a hard surface or receives a
substantial impact. If glass breaks, do not touch or attempt to
remove. Stop using your phone until the glass is replaced by a
qualified service center.
Seizures/Blackouts
Some people may be susceptible to epileptic seizures or blackouts
when exposed to flashing lights, such as when playing video
games. These may occur even if a person has never had a previous
seizure or blackout.
120
Safety Information
Repetitive Motion
When you repetitively perform actions such as pressing keys or
entering finger-written characters, you may experience occasional
discomfort in your hands, arms, shoulders, neck, or other parts of
your body. If you continue to have discomfort during or after such
use, stop use and see a physician.
Service & Repairs
If you have questions or need assistance, we’re here to help.
Go to www.motorola.com/iden, where you can select from a
number of customer care options. You can also contact the
Motorola Customer Support Center at 1-800-453-0920 (United
States), 1-877-483-2840 (TTY/TDD United States for hearing
impaired).
Export Law Assurances
This product is controlled under the export regulations of the
United States of America and Canada. The Governments of the
United States of America and Canada may restrict the exportation
or re-exportation of this product to certain destinations. For further
information contact the U.S. Department of Commerce or the
Canadian Department of Foreign Affairs and International Trade.
Service & Repairs
Service & Repairs
121
Specific Absorption Rate Data
ALL MODELS WITH FCC ID IHDT56HF1 MEET THE
GOVERNMENT’S REQUIREMENTS FOR EXPOSURE TO RADIO
WAVES.
Your wireless phone is a radio transmitter and receiver. It is
designed and manufactured not to exceed the emission limits for
exposure to radio frequency (RF) energy set by the Federal
Communications Commission of the U.S. Government. These limits
are part of comprehensive guidelines and establish permitted
levels of RF energy for the general population. The guidelines are
based on standards that were developed by independent scientific
organizations through periodic and thorough evaluation of
scientific studies. The standards include a substantial safety
margin designed to assure the safety of all persons, regardless of
age and health.
The exposure standard for wireless mobile phones employs a unit
of measurement known as the Specific Absorption Rate, or SAR.
The SAR limit set by the FCC is 1.6W/kg.1 Tests for SAR are
conducted using standard operating positions reviewed by the FCC
with the phone transmitting at its highest certified power level in
all tested frequency bands. Although the SAR is determined at the
highest certified power level, the actual SAR level of the phone
while operating can be well below the maximum value. This is
because the phone is designed to operate at multiple power levels
so as to use only the power required to reach the network. In
SAR Data
122
SAR Data
general, the closer you are to a wireless base station antenna, the
lower the power output.
Before a phone model is available for sale to the public, it must be
tested and certified to the FCC that is does not exceed the limit
established by the government-adopted requirement for safe
exposure. The tests are performed in positions and locations (e.g.,
at the ear and worn on the body) as required by the FCC for each
model. The highest SAR value for this model phone when tested
for use at the ear is 1.31 W/kg and when tested on the body, as
described in this user guide, is 1.51 W/kg during packet data
transmission. (Body-worn measurements differ among phone
models, depending upon available accessories and FCC
requirements.)2
While there may be differences between the SAR levels of various
phones and at various positions, they all meet the government
requirement for safe exposure. Please note that improvements to
this product model could cause differences in the SAR value for
later products; in all cases, products are designed to be within the
guidelines.
Additional information on Specific Absorption Rates (SAR) can be
found on the Cellular Telecommunications Industry Association
(CTIA) web-site at http://www.ctia.org or the Canadian Wireless
Telecommunications Association (CWTA) Web site:
http://www.cwta.ca
1. In the United States and Canada, the SAR limit for mobile
phones used by the public is 1.6 watts/kg (W/kg) averaged over
one gram of tissue. The standard incorporates a substantial margin
of safety to give additional protection for the public and to account
for any variations in measurements.
2. The SAR information includes the Motorola testing protocol,
assessment procedure, and measurement uncertainty range for
this product.
SAR Data
123
Motorola Limited Warranty for the United States and
Canada
What Does this Warranty Cover?
Note: FOR IDEN SUBSCRIBER PRODUCTS, ACCESSORIES
AND SOFTWARE PURCHASED IN THE UNITED STATES OR
CANADA
What Does this Warranty Cover?
Subject to the exclusions contained below, Motorola, Inc. warrants
its Motorola iDEN Digital Mobile and Portable Handsets
("Products"), Motorola-branded or certified accessories sold for
use with these Products ("Accessories") and Motorola software
contained on CD-Roms or other tangible media and sold for use
with these Products ("Software") to be free from defects in
materials and workmanship under normal consumer usage for the
period(s) outlined below. This limited warranty is a
consumer's exclusive remedy, and applies as follows to
new Products, Accessories and Software purchased by
124
SAR Data
consumers in the United States or Canada, which are
accompanied by this written warranty:
Products Covered
Length of Coverage
Products as defined
above.
One (1) year from the
date of purchase by the
first consumer
purchaser of the
product.
Accessories as
defined above.
One (1) year from the
date of purchase by the
first consumer
purchaser of the
product.
Products or
Accessories that are
Repaired or
Replaced.
The balance of the
original warranty or
for ninety (90) days
from the date returned
to the consumer,
whichever is longer.
Products Covered
Length of Coverage
Software as defined
above. Applies only to
physical defects in the
media that embodies
the copy of the software
(e.g. CD-ROM, or floppy
disk).
Ninety (90) days from
the date of purchase.
What is not covered? (Exclusions)
Normal Wear and Tear. Periodic maintenance, repair and
replacement of parts due to normal wear and tear are excluded
from coverage.
Ornamental Decorations. Ornamental decorations such as
emblems, graphics, rhinestones, jewels, gemstones and their
settings, and other decorative elements, are excluded from
coverage.
Batteries. Only batteries whose fully charged capacity falls below
80% of their rated capacity and batteries that leak are covered by
this limited warranty.
Abuse & Misuse. Defects or damage that result from: (a)
improper operation, storage, misuse or abuse, accident or neglect,
such as physical damage (cracks, scratches, etc.) to the surface of
the product resulting from misuse; (b) contact with liquid, water,
rain, extreme humidity or heavy perspiration, sand, dirt or the like,
extreme heat, or food; (c) use of the Products or Accessories for
commercial purposes or subjecting the Product or Accessory to
abnormal usage or conditions; or (d) other acts which are not the
fault of Motorola, are excluded from coverage.
Use of Non-Motorola Products and Accessories. Defects or
damage that result from the use of Non-Motorola branded or
certified Products, Accessories, Software or other peripheral
equipment are excluded from coverage.
Unauthorized Service or Modification. Defects or damages
resulting from service, testing, adjustment, installation,
maintenance, alteration, including without limitation, software
changes, or modification in any way by someone other than
Motorola, or its authorized service centers, are excluded from
coverage.
Altered Products. Products or Accessories with (a) serial
numbers or date tags that have been removed, altered or
obliterated; (b) broken seals or that show evidence of tampering;
(c) mismatched board serial numbers; or (d) nonconforming or
non-Motorola housings, antennas, or parts, are excluded from
coverage.
Communication Services. Defects, damages, or the failure of
Products, Accessories or Software due to any communication
service or signal you may subscribe to or use with the Products,
Accessories or Software is excluded from coverage.
Software Embodied in Physical Media. No warranty is made
that the software will meet your requirements or will work in
combination with any hardware or software applications provided
by third parties, that the operation of the software products will be
SAR Data
125
uninterrupted or error free, or that all defects in the software
products will be corrected.
Software NOT Embodied in Physical Media. Software that is
not embodied in physical media (e.g. software that is downloaded
from the internet), is provided "as is" and without warranty.
Who is covered? This warranty extends only to the first
consumer purchaser, and is not transferable.
What will Motorola Do? Motorola, at its option, will at no
charge repair, replace or refund the purchase price of any Products,
Accessories or Software that does not conform to this warranty.
We may use functionally equivalent
reconditioned/refurbished/pre-owned or new Products,
Accessories or parts. No data, software or applications added to
your Product, Accessory or Software, including but not limited to
personal contacts, games and ringer tones, will be reinstalled. To
avoid losing such data, software and applications please create a
back up prior to requesting service.
How to Obtain Warranty Service or Other Information? To
obtain service or information, please call:
Motorola iDEN Customer Services 1-800-453-0920 or
954-723-4910
TTY-877-483-2840
Or visit us online at http://www.motorola.com/iden/support
You will receive instructions on how to ship the Products,
Accessories or Software, at your expense, to a Motorola
Authorized Repair Center. To obtain service, you must include: (a) a
126
SAR Data
copy of your receipt, bill of sale or other comparable proof of
purchase; (b) a written description of the problem; (c) the name of
your service provider, if applicable; (d) the name and location of the
installation facility (if applicable) and, most importantly; (e) your
address and telephone number.
What Other Limitations Are There? ANY IMPLIED
WARRANTIES, INCLUDING WITHOUT LIMITATION THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE, SHALL BE LIMITED TO THE DURATION OF
THIS LIMITED WARRANTY, OTHERWISE THE REPAIR,
REPLACEMENT, OR REFUND AS PROVIDED UNDER THIS EXPRESS
LIMITED WARRANTY IS THE EXCLUSIVE REMEDY OF THE
CONSUMER, AND IS PROVIDED IN LIEU OF ALL OTHER
WARRANTIES, EXPRESS OF IMPLIED. IN NO EVENT SHALL
MOTOROLA BE LIABLE, WHETHER IN CONTRACT OR TORT
(INCLUDING NEGLIGENCE) FOR DAMAGES IN EXCESS OF THE
PURCHASE PRICE OF THE PRODUCT, ACCESSORY OR SOFTWARE,
OR FOR ANY INDIRECT, INCIDENTAL, SPECIAL OR
CONSEQUENTIAL DAMAGES OF ANY KIND, OR LOSS OF
REVENUE OR PROFITS, LOSS OF BUSINESS, LOSS OF
INFORMATION OR DATA, SOFTWARE OR APPLICATIONS OR
OTHER FINANCIAL LOSS ARISING OUT OF OR IN CONNECTION
WITH THE ABILITY OR INABILITY TO USE THE PRODUCTS,
ACCESSORIES OR SOFTWARE TO THE FULL EXTENT THESE
DAMAGES MAY BE DISCLAIMED BY LAW.
Some states and jurisdictions do not allow the limitation or
exclusion of incidental or consequential damages, or limitation on
the length of an implied warranty, so the above limitations or
exclusions may not apply to you. This warranty gives you specific
legal rights, and you may also have other rights that vary from
state to state or from one jurisdiction to another.
Laws in the United States and other countries preserve for
Motorola certain exclusive rights for copyrighted Motorola
software such as the exclusive rights to reproduce and distribute
copies of the Motorola software. Motorola software may only be
copied into, used in, and redistributed with, the Products
associated with such Motorola software. No other use, including
without limitation disassembly of such Motorola software or
exercise of the exclusive rights reserved for Motorola, is
permitted.
Patent and Software Provisions
MOTOROLA will defend, at its own expense, any suit brought
against the end user purchaser to the extent that it is based on a
claim that the Product or parts infringe a United States patent, and
Motorola will pay those costs and damages finally awarded
against the end user purchaser in any such suit which are
attributable to any such claim, but such defense and payments are
conditioned on the following:
a.That MOTOROLA will be notified promptly in writing by such
purchaser of any notice of such claim;
b.That MOTOROLA will have sole control of the defense of
such suit and all negotiations for its settlement or
compromise; and
c.Should the Product or parts become, or in MOTOROLA'S opinion
be likely to become, the subject of a claim of infringement of a
United States patent, that such purchaser will permit MOTOROLA,
at its option and expense, either to procure for such purchaser the
right to continue using the Product or parts or to replace or modify
the same so that it becomes non-infringing or to grant such
purchaser a credit for the Product or parts as depreciated and
accept its return. The depreciation will be an equal amount per
year over the lifetime of the Product or parts as established by
MOTOROLA.
MOTOROLA will have no liability with respect to any claim of
patent infringement which is based upon the combination of the
Product or parts furnished hereunder with software, apparatus or
devices not furnished by MOTOROLA, nor will MOTOROLA have
any liability for the use of ancillary equipment or software not
furnished by MOTOROLA which is attached to or used in
connection with the Product or any parts thereof.
Laws in the United States and other countries preserve for
MOTOROLA certain exclusive rights for copyrighted MOTOROLA
software, such as the exclusive rights to reproduce in copies and
distribute copies of such MOTOROLA software. MOTOROLA
software may be used in only the Product in which the software
was originally embodied and such software in such Product may
not be replaced, copied, distributed, modified in any way, or used
to produce any derivative thereof. No other use including, without
limitation, alteration, modification, reproduction, distribution, or
reverse engineering of such MOTOROLA software or exercise or
rights in such MOTOROLA software is permitted. No license is
SAR Data
127
granted by implication, estoppel or otherwise under MOTOROLA
patent rights or copyrights.
128
SAR Data
Hearing Aid Compatibility
A number of Motorola phones have been tested for hearing aid
compatibility. When some wireless phones are used with certain
hearing aids, users may detect a noise which can interfere with
the effectiveness of the hearing aid.
Some hearing aids are more “immune” than others to this
interference noise, and phones can also vary in the amount of
interference noise they may generate. ANSI standard C63.19 was
developed to provide a standardized means of measuring both
mobile phone and hearing aids to determine usability rating
categories for both.
Ratings have been developed for mobile phones to assist hearing
aid users find phones that may be compatible with their hearing
aid. Not all phones have been rated for compatibility with hearing
aids. Phones that have been rated have a label with the rating(s)
located on the box, and at www.motorola.com/accessibility.
These ratings are not guarantees of compatibility. Results will vary
depending on the user's hearing aid and individual type and degree
of hearing loss. If a hearing aid is particularly vulnerable to
interference, even a phone with a higher rating may still cause
unacceptable noise levels in the hearing aid Trying out the phone
with your hearing aid is the best way to evaluate it for your
personal needs.
HAC
“M” Rating: Phones rated M3 or M4 meet FCC requirements for
hearing aid compatibility and are likely to generate less
interference to hearing aids than unrated phones. (M4 is the
“better” or higher of the two ratings.) On those models with an
extendable antenna, this rating is determined only with the
antenna extended.
“T” Rating: Phones rated T3 or T4 meet FCC requirements and are
likely to be more usable with a hearing aid's telecoil (“T Switch” or
“Telephone Switch”) than unrated phones. (T4 is the “better” or
higher of the two ratings.) On those models with a telecoil mode
setting, this rating is determined only with the phone so set. For
setting instructions, see “Features for the Hearing Impaired” in the
section entitled “Advanced Calling Features”. Note that not all
hearing aids have telecoils in them.
Hearing aids may also be measured for immunity to interference
from wireless phones and may have ratings similar to wireless
phones. Ask your hearing health care professional for the rating of
your hearing aid. Add the rating of your hearing aid and your phone
to determine the estimated usability:
• Any combined rating equal to or greater than six offers
excellent use.
• Any combined rating equal to five is considered normal
use.
HAC
129
• Any combined rating equal to four is considered usable.
Thus, if you use an M3 phone with a M3 hearing aid you will have
a combined rating of six for “excellent use.” This methodology
applies equally for T ratings.
More information about hearing aid compatibility may be found at:
www.motorola.com/accessibility, www.fcc.gov, www.fda.gov, and
www.hearingloss.org/learn/cellphonetech.asp
130
HAC
Information From the World Health Organization
Present scientific information does not indicate the need for any
special precautions for the use of mobile phones. If you are
concerned, you may want to limit your own or your children’s RF
WHO Information
exposure by limiting the length of calls or by using hands-free
devices to keep mobile phones away from your head and body.
Source: WHO Fact Sheet 193
Further information: http://www.who.int./peh-emf
Product Registration
Online Product Registration:
http://direct.motorola.com/hellomoto/
Motosupport/source/registration.asp
Product registration is an important step toward enjoying your new
Motorola product. Registering helps us facilitate warranty service,
and permits us to contact you should your product require an
update or other service. Registration is for U.S. residents only and
is not required for warranty coverage.
Please retain your original dated sales receipt for your records. For
warranty service of your Motorola Personal Communications
Product you will need to provide a copy of your dated sales receipt
to confirm warranty status.
Thank you for choosing a Motorola product.
Registration
WHO Information
131
Wireless: The New Recyclable
Your wireless phone can be recycled. Recycling your phone
reduces the amount of waste disposed in landfills and allows
recycled materials to be incorporated into new products.
The Cellular Telecommunications Industry Association (CTIA) and
its members encourage consumers to recycle their phones and
have taken steps to promote the collection and environmentally
sound recycling of end-of-life devices.
Recycling
California Perchlorate Label
Some mobile phones use an internal, permanent backup battery on
the printed circuit board that may contain very small amounts of
perchlorate. In such cases, California law requires the following
label:
“Perchlorate Material - special handling may apply. See
www.dtsc.ca.gov/hazardouswaste/perchlorate.”
There is no special handling required by consumer.
Perchlorate Label
132
Recycling
As a phone user, you have an important role in ensuring that this
device is recycled properly. When it comes time to give this phone
up or trade it in for a new one, please remember that the phone,
the charger, and many of its accessories can be recycled. It's easy.
To learn more about CTIA's Recycling Program for Used Wireless
Devices, please visit us at:
http://recycling.motorola.young-america.com/ index.html
Patent and Trademark Information
MOTOROLA, the Stylized M Logo and all other trademarks
indicated as such herein are trademarks of Motorola, Inc. ® Reg.
U.S. Pat. & Tm. Off. © 2007 Motorola, Inc. All rights reserved.
Microsoft and Microsoft Internet Explorer are registered
trademarks of Microsoft Corporation.
T9 is a trademark owned by Tegic Communications.
T9® Text Input Patent and Trademark Information.
This product is covered by U.S. Pat. 5,818,437, U.S. Pat. 5,953,541,
U.S. Pat. 6,011,554 and other patents pending.
Java and all other Java-based marks are trademarks or registered
trademarks of Sun Microsystems, Inc. in the U.S. and other
countries.
All other product names or services mentioned in this manual are
the property of their respective trademark owners.
Patent and Trademark
Software Copyright Notice
The Motorola products described in this manual may include
copyrighted Motorola and third party software stored in
semiconductor memories or other media. Laws in the United
States and other countries preserve for Motorola and third party
software providers certain exclusive rights for copyrighted
software, such as the exclusive rights to distribute or reproduce
the copyrighted software. Accordingly, any copyrighted software
contained in the Motorola products may not be modified,
reverse-engineered, distributed, or reproduced in any manner to
the extent allowed by law. Furthermore, the purchase of the
Motorola products shall not be deemed to grant either directly or
by implication, estoppel, or otherwise, any license under the
copyrights, patents, or patent applications of Motorola or any third
party software provider, except for the normal, non-exclusive,
royalty-free license to use that arises by operation of law in the
sale of a product.
Patent and Trademark
133
Privacy and Data Security
Motorola understands that privacy and data security are important
to everyone. Because some features of your phone may affect your
privacy or data security, please follow these recommendations to
enhance protection of your information:
• Monitor access: Keep your phone with you and do not
leave it where others may have unmonitored access. Lock
your device’s keypad where this feature is available.
• Keep software up to date: If Motorola or a
software/application vendor releases a patch or software
fix for your phone which updates the device’s security,
install it as soon as possible.
• Erase before recycling: Delete personal information or
data from your phone prior to disposing of it or turning it in
for recycling. For step-by-step instructions on how to
delete all personal information from your device, please
contact your local service provider.
Privacy and Data Security
134
Privacy and Data Security
• Understanding AGPS: In order to comply with
emergency caller location requirements of the FCC, certain
Motorola phones incorporate Assisted Global Positioning
System (AGPS) technology. AGPS technology also can be
used in non-emergency applications to track and monitor a
user’s location, for example, to provide driving directions.
Users who prefer not to permit such tracking and
monitoring should avoid using such applications.
If you have further questions regarding how use of your phone may
impact your privacy or data security, please contact Motorola at
privacy@motorola.com, or contact your service provider.
Smart Practices While Driving
Drive Safe, Call Smart SM
Check the laws and regulations on the use of phones and
their accessories in the areas where you drive. Always
obey them. The use of these devices may be prohibited or
restricted in certain areas. Go to www.motorola.com/callsmart
for more information.
Your phone lets you communicate by voice and data, almost
anywhere, anytime, wherever wireless service is available and
safe conditions allow. When driving a car, driving is your first
responsibility. If you choose to use your phone while driving,
remember the following tips:
• Get to know your Motorola phone and its features
such as speed dial and redial. If available, these
features help you to place your call without taking your
attention off the road.
• When available, use a hands-free
device. If possible, add an additional
layer of convenience to your phone with
one of the many Motorola Original
hands-free accessories available today.
• Position your phone within easy reach. Be able to
access your phone without removing your eyes from the
Driving Safety
•
•
•
•
•
road. If you receive an incoming call at an inconvenient
time, if possible, let your voice mail answer it for you.
Let the person you are speaking with know you are
driving; if necessary, suspend the call in heavy
traffic or hazardous weather conditions. Rain, sleet,
snow, ice, and even heavy traffic can be hazardous.
Do not take notes or look up phone numbers while
driving. Jotting down a “to do” list or going through your
address book takes attention away from your primary
responsibility, driving safely.
Dial sensibly and assess the traffic; if possible,
place calls when your car is not moving or before
pulling into traffic. If you must make a call while
moving, dial only a few numbers, check the road and your
mirrors, then continue.
Do not engage in stressful or emotional
conversations that may be distracting. Make people
you are talking with aware you are driving and suspend
conversations that can divert your attention away from the
road.
Use your phone to call for help. Dial 911 or other local
emergency number in the case of fire, traffic accident, or
medical emergencies.**
Driving Safety
135
• Use your phone to help others in emergencies. If you
see an auto accident, crime in progress, or other serious
emergency where lives are in danger, call 911 or other
local emergency number, as you would want others to do
for you.**
• Call roadside assistance or a special
non-emergency wireless assistance number when
necessary. If you see a broken-down vehicle posing no
serious hazard, a broken traffic signal, a minor traffic
accident where no one appears injured, or a vehicle you
know to be stolen, call roadside assistance or other
special non-emergency wireless number.*
* Wherever wireless phone service is available.
136
Driving Safety
index
A
B
accessories 10, 30
activate your Mike
account 11
active phone line 81
advanced calling 103
3-way calls 103
call waiting 103
alarm clock 104
do not disturb 105
quick timer 104
stop watch 104
alert
set 92, 93
turn off 92, 96
answer a call 19
backlight 111
battery 16, 17
battery indicator 81
Bluetooth
connect 75
send information 77
turning on or off 75
bluetooth 74
C
call
answer 19
any key answer 104
end 19
make 19
call forward 97
caller ID 97
camera 39, 43
digital viewfinder 45
photo editor 45
record video 44
self-timer 44
center key 84
center select key 10
clock 111
clock screen saver 79
codes 85
contacts 105
edit/delete 105
set picture ID 105
set ringer ID 105
D
datebook 106
index
137
create events 106
receive events
via PTT 106
setup 94
view reminders 106
dial a phone number 19
dialed calls 96
display 80
Drafts 26
see also text messages,
drafts
E
earpiece volume 92
emergency number 99
end a call 19
end key 19
export regulations 121
138
index
F
H
features for the vision
impaired 90
find your phone number 23
flip 19
flip activation 104
frequently asked questions
service and repairs 121
handsfree 108
auto answer 109
speaker-phone 108
handsfree speaker 84
hearing aid 88
Hearing Aid
Compatibility 129
home screen 80
G
GPS 107
approximate location 107
emergency calls 107
privacy options 107
security PIN 108
GPS enabled
emergency calls 99
GPS PIN 85
GPS, see GPS enabled
I
international calls 100, 101
K
keypad
locking 85
L
language 111
lock
phone 85
low battery message 81
M
main menu 81
make a call 19
media center 40
Memory
text messages 27
memory card 13, 109
manage memory 110
ring tones 92
storage preferences 109
menu style 111
Message center
text messages 25
messages
fax mail indicator 101
read messages 110
reply 110
MMS 55
modem
using your handset
as a 28
music player 31
N
navigation key 10, 84
net alerts 102
O
one touch PTT 54
optional accessory 10
optional feature 10
P
packet data 81
passwords 85
passwords. See codes
PC applications 111
personalize 110, 111
phone
locking 85
phone number 23
power key 18
private calls
answer 20
call alerts 20
make 19
receive a call alert 21
PT Manager 55
PTT features
push to send 47
Push To View 47
Q
quick notes
create, edit 24, 26
R
radio frequency 116
received calls 96
recent calls 96
recycling 132
index
139
redial 97
ring style indicator 81
ring tones
off 92, 93
setting 92
vibrate 92, 93
ring tones, setting 92
ringer volume 92
SIM PIN 85
slide show
view 66
soft keys 80
speaker 81
speed dial 100
store your number 23
T
S
safety
radio frequency 116
RF energy
interference 117
safety information 116
safety tips 135
security 85, 112
security code 85
send key 19
signal strength indicator 80
SIM card 11
security 12
140
index
text 23
text entry 81
alpha method 83
word method 82
text messages 23
creating 25
deleting 26, 27
drafts 26
memory 27
message center 25
receiving 24
resend messages 26
sending 25
sent messages 26
setting up 23
transmitter 86
TTY calls 112
turn on/off 18
U
unlock
phone 85
unlock code 85
V
video 44, 45
voice mail
advance voice mail with
fax 101
receiving 100
voice name 98
voicemail 100
voicemail message
indicator 100
volume 92
W
wallpaper 93
WHO information 131
wireless web 72
microbrowser
navigation 73
index
141