VTech ia5829 - Cordless Phone - Operation Specifications

Table of Contents
Important Safety Instructions......................................................................................1
Before You Begin ..............................................................................................................3
Parts Check List ..................................................................................................................3
The Handset Layout......................................................................................................4
The Base Unit Layout.........................................................................................................5
Getting Started...................................................................................................................6
Setup........................................................................................................................6
Connecting Power to Base Unit .....................................................................................6
Installation and Charge of Battery...............................................................................6
Low Battery Indication ......................................................................................7
Battery Care and Maintenance ......................................................................................7
Connecting to Phone Line .............................................................................................7
Check for Dial Tone.................................................................................................8
Set Date and Time................................................................................................8
Wall Mounting....................................................................................................8
Basic Operation..............................................................................................................9
Telephone Operation ..................................................................................................9
Handset Operation.........................................................................................9
Base Operation .........................................................................................10
Handset Ringer Style/Battery Save.......................................................................11
Set the Dail Mode.........................................................................................11
Temporary Tone Dialing........................................................................................11
Message Waiting......................................................................................................11
Clear Message Waiting Alert....................................................................12
Display Screen Messages .........................................................................................12
Speed Dial Memory.....................................................................................13
Store a Number/Name in Speed Dial Memory ..................................................13
Edit a Number/Name Stored in Memory .........................................................14
Delete a Number/Name Stored in Memory ......................................................14
Dial a Memory Number ....................................................................................15
Reassign Locations in Memory ....................................................................................15
Telephone Directory...........................................................................................16
Store a Number/Name in the Directory ...........................................................16
Edit a Number/Name Stored in the Directory ....................................................17
Delete a Number/Name Stored in the Directory ...............................................17
Dial a Number from the Directory.......................................................................18
Move a Number/Name to the Memory.................................................................18
Caller ID Operation.................................................................................................19
Table of Contents
About Call History .............................................................................................19
Review Call History .........................................................................................19
Delete Records from Call History..............................................................................19
Dial a Displayed Number...................................................................................20
Store a Call History Record in the Directory.......................................................20
Display Screen Messages.................................................................................20
Additional Information.................................................................................................21
Headset Operation...................................................................................................21
Maintenance..................................................................................................................22
In Case of Difficulty...................................................................................................23
Warranty Statement.................................................................................................25
FCC, ACTA and IC Regulations.................................................................................27
Technical Specifications......................................................................................30
Important Safety Instructions
When using your telephone equipment, basic safety precautions should always
be followed to reduce the risk of fire, electric shock and injury, including the
following:
1. Read and understand all instructions.
2. Follow all warnings and instructions marked on the product.
3. Unplug this product from the wall outlet before cleaning. Do not use liquid
or aerosol cleaners. Use a damp cloth for cleaning.
4. Do not use this product near water (for example, near a bath tub, kitchen
sink or swimming pool).
5. Do not place this product on an unstable surface, such as a table, shelf, or
stand. The product may fall, causing serious damage.
6. Slots and openings in the back or bottom of the base unit and handset are
provided for ventilation. To protect them from overheating, these openings
must not be blocked by placing the product on a soft surface such as a bed,
sofa or rug. This product should never be placed near or over a radiator or
heat register. This product should not be placed in any area where proper
ventilation is not provided.
7. This product should be operated only from the type of power source indicated
on the marking label. If you are not sure of the type of power supply in your
home, consult your dealer or local power company.
8. Do not allow anything to rest on the power cord. Do not install this product
where the cord may have anyone walking on it.
9. Never push objects of any kind into this product through slots in the base or
handset as they may touch dangerous voltage points or short out parts that
could result in a risk of fire or electric shock. Never spill liquid of any kind on
the product.
10. To reduce the risk of electric shock, do not disassemble this product, but
take it to an authorized service facility. Opening or removing parts of the
base or handset other than specified access doors may expose you to
dangerous voltages or other risks. Incorrect reassembling can cause
electric shock when the product is subsequently used.
11. Do not overload wall outlets and extension cords as this can result in the
risk of fire or electric shock.
12. Unplug this product from the wall outlet and refer servicing to an authorized
service facility under the following conditions:
1
Important Safety Instructions
A. When the power supply cord or plug is damaged or frayed.
B. If liquid has been spilled onto the product.
C. If the product has been exposed to rain or water.
D. If the product does not operate normally by following the operating
instructions. Adjust only those controls that are covered by the operating
instructions, as improper adjustment of other controls may result in
damage and often requires extensive work by an authorized technician
to restore the product to normal operation.
E. If the product has been dropped and the base and/or handset has been
damaged.
F. If the product exhibits a distinct change in performance.
13. Avoid using a telephone (other than cordless) during an electrical storm.
There is a remote risk of electric shock from lightning.
14. Do not use the telephone to report a gas leak in the vicinity of the leak.
15. Only put the handset of your telephone next to your ear when it is in normal
talk mode.
2
Before You Begin
Enhanced 5.8GHz Technology - Dual band transmission combines the best of
5.8GHz and 900MHz technologies, providing enhanced performance over
standard cordless telephones.
Parts Check List
1.
2.
3.
4.
Base Unit
Handset
Base Power Adaptor
Telephone Line Cord
5.
6.
7.
8.
Battery
Belt Clip
User’s Manual
Wall Mount Bracket
To purchase replacement batteries, visit us on the web at www.vtechphones.com
or call VTech Communications, Inc. at 1-800-595-9511. In Canada, call VTech
Telecommunications Canada Ltd. at 1-800-267-7377.
Wall Mount Bracket
Handset
Battery
Base Unit
Belt Clip
Base Power Adaptor
Telephone
Line Cord
3
User’s Manual
(English and Spanish)
The Handset Layout
1
2
3
4
9
10
5
11
12
6
1.
2.
3.
4.
5.
6.
7.
8.
7
13
8
14
Antenna
Earpiece
LCD
Left and Right Arrow Keys
Phone/Flash Key
Dialing Keys (0-9,*,#)
Chan/Delete Key
Microphone
9.
10.
11.
12.
13.
14.
4
Headset Jack
Select Key
Off Key
Hold Key
Redial/Pause Key
Prog Key
The Base Unit Layout
3
1
2
4
5
1. Message Light
2. Locate Handset Key
3. Charging/In use Light
4. Telephone Line Jack
5. DC Connector Jack
5
Getting Started
Setup
Connecting Power to Base Unit
1. Choose a location for the base
near an electrical outlet and a telephone jack. This phone requires
a modular telephone jack and a
standard electrical outlet (110V
AC) not controlled by a wall
switch.
Connect the
power cord
Standard electrical outlet
2. Plug the DC connector to the base.
Plug the AC adaptor into an electrical outlet.
Installation and Charge of Battery
1. Install the battery. Use only VTech batteries.
a) Remove battery
compartment cover
by pressing on the
indentation and sliding
downward.
b) Align the two holes in the plug with the
socket pins, then snap the plug into place.
c) Place the battery in the compartment
with the wires in the lower right corner.
d) Replace the battery compartment cover.
e) If the battery is not already charged,
place the handset in its base and allow
to charge for 10 - 12 hours (or overnight). After that, be sure to place the
handset in its base when not in use to
ensure maximum daily performance.
6
2.
If the phone will not be used for long periods of time, remove the battery to
prevent possible leakage.
NOTE: Install the base unit away from electronic equipment, such as personal
computers, television sets or microwave ovens. Avoid excessive heat, cold, dust
or moisture.
Low Battery Indication: If the battery power becomes
low, a low-battery icon will be shown at the lower left
corner of handset display. The handset will beep until
you place the handset in the charger. When in standby
mode, the low-battery display is shown:
BATTERY
1/0
1
LOW
12:00 AM
Battery Care and Maintenance
•
•
•
•
•
The maximum standby time on a fully charged battery is six days. Average
talk time on a fully charged battery is five hours.
The battery needs charging when:
— A new battery is installed in the handset.
— The phone beeps twice every five seconds.
— The screen displays BATTERY LOW and the low battery icon.
Place the handset in its base so the CHARGING light turns on. The battery
is typically fully charged in 12 hours.
You can keep the battery fully charged by returning the handset to its base
after each use.
If you repeatedly get a low battery indicator, even after charging overnight, the
battery should be replaced. Use only VTech batteries.
CAUTION! To reduce the risk of fire or injury to persons or damage to
the telephone, read and follow these instructions carefully:
Charge the battery provided with or identified for use with this
product only in accordance with the instructions and limitations
specified in the user’s manual.
Connecting to Phone Line
Before connecting to the phone, make
sure to properly charge the battery for at
least 10 - 12 hours.
Plug one end of the telephone line cord
into the jack on the bottom of the base
unit. Plug the other end of this cord into
the wall jack.
Connect the
telephone line cord
Modular telephone jack
7
Getting Started
Setup
Getting Started
Setup
Check for Dial Tone
After the battery is charged, pick up the handset and press PHONE/FLASH. You should
hear a dial tone.
Set Date and Time
If you subscribe to caller ID service, the date and time will be set automatically with
the first incoming call. If you do not have caller ID service, you can set the date and
time manually:
•
•
•
•
•
•
•
Press PROG on the handset.
Press or until DATE/TIME is displayed. Press SELECT.
The month is flashing. Press or until the screen displays the correct
month. Press SELECT.
The day is flashing. Press
or
until the screen displays the correct
day. Press SELECT.
The hour is flashing. Press or until the screen displays the correct
hour. Press SELECT.
The minute is flashing. Press
or until the screen displays the correct
minute. Press SELECT.
AM or PM is flashing. Press
or
to choose between AM or PM.
Press SELECT.
Wall Mounting
The wall mount bracket is designed for use on standard wall mount plates only.
1. Run the power and telephone line cords through the slots in the bracket,
connecting them to the jacks located on the underside of the base.
2. Plug the AC adapter into an electrical outlet. If the battery has not been
previously charged, place the handset in the base, and allow it to charge for 1012 hours (or overnight).
3. Connect the telephone line cord to the wall jack.
4. Line up the tabs on the
wall mount bracket with the
slots on the bottom of the
base unit. Snap the bracket
firmly in place.
5. Mount the base on the
wall. Position the base unit
so the mounting studs will
fit into the holes on the wall
mount bracket. Slide the
base unit down on the
mounting studs until it locks
into place.
8
Telephone Operation
Operation
SELECT
/ CID
• Use SELECT in conjunction
with PROG during handset
programming.
• While on a call, press to
decrease the volume. A
double beep will sound
when you reach the minimum setting.
• While phone is not in use,
press to display caller ID
information.
• While entering number or
letters, press to delete last
character entered.
/
• While on a call, press to increase the volume. A double
beep will sound when you
reach the maximum setting.
• While phone is not in use,
press to display phonebook
entries.
• While entering letters, press
to advance cursor.
(phone) / FLASH
• To make a call, press then
dial the number. or dial the
number (use < to backspace and correct digits),
then press
(phone)/
FLASH.
• During a call, press to receive an incoming call, if
call waiting is activated.
• To answer a call, press
this or any key except
(off).
(off)
• To end a call, press this key
or place handset in base.
• While programming, press
to exit.
• While paging, press
to
cancel.
REDIAL/PAUSE
• To call last number dialed,
press REDIAL/PAUSE, then
press
(phone)/FLASH
-OR-
HOLD
• Press to put a call on hold.
• To release hold, press it
again or press phone or
lift the handset of an extension.
• Press
(phone)/FLASH
then press REDIAL/PAUSE.
• To delete the last number dialed record, press twice
while handset is idle.
• While entering numbers,
press REDIAL/ PAUSE to insert a dialing pause.
CHAN/ DELETE
• Press to switch to a clear
channel while on a call.
• When viewing the all log,
press to delete the current record displayed.
• Press and hold to delete
all calls log while handset
is idle.
PROG
• Press to enter programming
mode with handset idle (on
hook).
9
Basic Operation
Handset
Telephone Operation
Basic Operation
Base Operation
In Use/Charging
Indicator
Message Waiting
Indicator
• Flashes slowly when
the handset is in use.
• Flashes rapidly when a
call is on hold.
• Glows steadily when
the handset is charging
in its base.
• If you subscribe to telephone company voice
mail with a visual message waiting signal,
this light flashes, and
MESSAGES WAITING
displays on the handset screen when you
have voice mail waiting.
Page/Handset Locator
• Press to page the handsets. Press again, press
(off) on handset, or
place handset in the
base to cancel the page.
10
Telephone Operation
Handset Ringer Style/Battery Save
You can select from four different handset ringer styles, or turn the ringer off and
extend the battery life.
1. Make sure the handset is off.
2. Press PROG.
3. Press until the screen displays RINGER: and the current selection.
4. Press SELECT. The current setting blinks, and you will hear a sample of the
ring.
(off). You will hear a sample
5. Press or to select RINGER: 1, 2, 3, 4 or
of each ring.
6. Press SELECT to choose the displayed ringer setting.
If you have touch tone service, the phone is ready to use as soon as the battery
is charged. If you have pulse (rotary) service, you’ll need to change the dial mode.
•
•
•
•
•
Press PROG on the handset.
Press or until the screen displays DIAL MODE: and the current selection.
Press SELECT. The current setting blinks.
Press to select TONE or PULSE.
Press SELECT to save the displayed mode.
Temporary Tone Dialing
If you have pulse (rotary) service only, you can change from pulse to touch tone
dialing during a call by pressing * (TONE). This is useful if you need to send
touch tone signals for access to telephone banking or long distance services.
1. Dial the number.
2. Press * (TONE). Buttons pressed after this send touch tone signals.
3. After you hang up, the phone automatically returns to pulse service.
Message Waiting
Your ia 5829 is designed to work with most local and regional telephone service
provider's voice messaging systems, providing alerts on both the handset and
base unit when new messages come in.
Voice messaging is subscription service, available through most service
providers, for a monthly fee. Contact your local telephone company for more
information.
When a caller leaves a message in your voice mailbox, the MESSAGE light on
the base unit will flash. In addition, the handset will display:
11
Basic Operation
Set the Dial Mode
Telephone Operation
MESSAGES
5/01
WAITING
5:40PM
Clear Message Waiting Alert
If you wish to manually turn off the message waiting light:
1. Press PROG.
2. Press or until screen displays MESSAGES WAITING.
3. Press SELECT, the screen displays:
Basic Operation
LIGHT OFF: YES
4. Press or to change from YES or NO.
5. Press SELECT to choose the desired setting. You’ll hear a confirmation tone.
Display Screen Messages
Screen Displays:
When:
** RINGING **
There is a call coming in.
CONNECTING...
The handset is waiting for a dial tone.
PHONE
The handset is in use.
ON
SCANNING...
The handset is changing to another of the 30
channels available.
** PAGING **
The base is paging the handset.
HOLD
There is a call on hold.
BATTERY
NO
LOW
CONNECT
MESSAGES
RINGER
WAITING
OFF
The battery needs to be recharged.
Displays and a sad tone sounds when the base
(phone) / FLASH is pressed.
power is off and
You have been alerted by the telephone company
that you have received new voice mail.
The ringer is turned off.
12
Speed Dial Memory
You can store up to nine telephone numbers with names (up to 15 characters and 24
digits in each location) into the speed dial memory locations you assign (1 through 9).
You can also store telephone numbers with names alphabetically in the directory. See
Telephone Directory for instructions.
NOTES:
• The entries you store in speed dial memory will be marked with 01 through 09 in the
telephone directory.
• Press
(off) at any time to exit memory mode.
1. Press PROG on the handset.
2. Press
or
until the screen displays SPEED DIAL.
3. Press SELECT. The screen displays ENTER 1-9.
NOTE: When memory is full the screen displays MEMORY FULL, an error tone sounds,
and you cannot store a new number until you delete a record in speed dial memory or
telephone directory.
4. Press the key (1 through 9) for the memory location where you’re storing this entry.
The screen displays ENTER NAME.
NOTE: If the location is not empty, your new entry will be stored in place of the old and the
first entry will be deleted. Take caution to not save over entries you do not wish to delete
from memory.
5. Using the chart below, enter up to 15 characters for the name you’re storing with the
to backspace and make corrections; use
to advance and add a
number. Use
space.
Dial Key
1:
2:
3:
4:
5:
6:
7:
8:
9:
0:
*:
#:
1
Presses
2 3 4 5 6
1
A
D
G
J
M
P
T
W
0
B
E
H
K
N
Q
U
X
C
F
I
L
O
R
V
Y
2
3
4
5
6
S
8
Z
&
’
,
-
7
9
.
13
#
Basic Operation
Store a Number/Name in Speed Dial Memory
Telephone Memory
Basic Operation
6. When you finish entering the name, press SELECT or PROG. The screen displays
ENTER NUMBER.
7. Enter the telephone number. Use
to backspace and make corrections.
Press REDIAL/PAUSE to store a pause in the dialing sequence.
-ORPress REDIAL/PAUSE to display the last number dialed from this phone.
8. Press SELECT or PROG to store your entry. The screen displays DISTINCT
RING? and the current setting.
9. Press or to change the setting. Choose Y (for yes) if you wish the phone
to alert you to calls from this number by changing to a distinctive ringing
pattern after the first ring. Choose N for a normal ringing pattern.
10. Press SELECT or PROG to confirm your selection. If you chose Y, a D will be
displayed with the memory entry.
Edit a Number/Name Stored in Memory
1. Press and hold the memory location key (1 through 9) of the entry you wish
to edit.
2. When the screen displays the entry you want to edit, press SELECT. Then
press or until EDIT flashes.
SPEED EDIT ERASE
8005959511
01
3. Press SELECT. The screen displays the name and number. The cursor
appears at the end of the name. Use , and the dial pad keys to edit the
name. Press SELECT to move on to edit the number. Use to backspace
and make corrections. Press SELECT to move to edit the distinctive ring
setting.
4. Press SELECT to save the edited information
Delete a Number/Name Stored in Memory
1. Press and hold the memory location key (1 through 9) of the entry you wish
to delete.
2. When the screen displays the entry you want to delete, press SELECT. Then
press or until ERASE flashes.
SPEED EDIT ERASE
8005959511
01
3. Press SELECT. The screen displays ERASE NO YES and the number.
4. Press or until YES flashes.
5. Press SELECT.You’ll hear a confirmation beep.
14
Telephone Memory
Dial a Memory Number
1. Press and hold the memory location key (1 through 9) of the entry you wish
to dial.
(phone) / FLASH to dial the displayed memory number.
2. Press
Reassign Locations in Memory
1. Press and hold the memory location key (1 through 9) of the entry you
wish to reassign.
2. When the screen displays the entry you want to reassign, press
SELECT. Then press until SPEED flashes.
01
3. Press SELECT. The screen displays ENTER 1-9.
4. Press the keys (1 through 9) to re-assign this entry into another memory
location. You will hear a confirmation beep.
15
Basic Operation
SPEED EDIT ERASE
8005959511
Telephone Directory
Your ia 5829 can store 20 (including nine speed dial entries) telephone numbers with
names (up to 15 characters for the name and 24 digits for the number in each location).
NOTE: Press
(off) at any time to exit directory.
Basic Operation
Store a Number/Name in the Directory
1. Press PROG. The screen displays DIRECTORY.
2. Press SELECT. The screen displays ENTER NAME.
3. Using the chart below, enter up to 15 characters for the name you’re storing with the
number. Use to backspace and make corrections; use to advance and add a
space.
Dial
DialKey
Key
1:
2:
3:
4:
5:
6:
7:
8:
9:
0:
*:
#:
11
Presses
Presses
2
2 33 44 55 66
1
A
D
G
J
M
P
T
W
0
B
E
H
K
N
Q
U
X
C
F
I
L
O
R
V
Y
2
3
4
5
6
S
8
Z
&
’
,
-
7
9
.
#
4. When you finish entering the name, press SELECT or PROG. The screen displays
ENTER NUMBER.
5. Enter the telephone number. Use to backspace and make corrections. Press
REDIAL/PAUSE to store a pause in the dialing sequence.
-ORPress REDIAL/PAUSE to display the last number dialed from this phone.
6. Press SELECT or PROG. The screen displays DISTINCT RING? and the current
setting.
7. Press or to change the setting. Choose Y (for yes) if you wish the phone to
alert you to calls from this number by changing to a distinctive ringing pattern after the
16
Telephone Directory
first ring. Choose N for a normal ringing pattern.
8. Press SELECT or PROG to confirm your selection. If you chose Y, a D will be
displayed with the directory entry.
Edit a Number/Name Stored in the Directory
1. Press . The screen displays DIRECTORY.
2. Press or to scroll alphabetically through the entries stored in the directory.
-ORPress the dial pad key for the first letter of the entry you want to edit.
3. When the screen displays the entry you want to edit, press SELECT. Then press
or until EDIT flashes.
SPEED EDIT
8005959511
ERASE
4. Press SELECT. The screen displays the name and number. The cursor appears at the end of the name. Use , and the dial pad keys to edit the
name. Press SELECT to move on to edit the number. Use to backspace
and make corrections. Press SELECT to move on to edit the distinctive ring
setting.
5. Press SELECT to save the edited information.
Delete a Number/Name Stored in the Directory
1. Press . The screen displays DIRECTORY.
2. Press or to scroll alphabetically through entries in the directory.
-ORPress the dial pad key for the first letter of the entry you want to delete.
3. When the screen displays the entry you want to delete, press SELECT. Then press
or until ERASE flashes.
SPEED EDIT
8005959511
ERASE
4. Press SELECT. The screen displays ERASE NO YES and the number. The current
choice flashes.
5. Press or until YES flashes.
6. Press SELECT. You’ll hear a confirmation beep.
17
Basic Operation
NOTE: When memory is full the screen displays MEMORY FULL, an error tone sounds,
and you will not be able to store a new number until you delete a stored number.
Telephone Directory
Dial a Number from the Directory
1. Press . The screen displays DIRECTORY.
or
to scroll alphabetically through entries stored in directory.
2. Press
-ORPress the dial pad key for the first letter of the entry you want to dial.
(phone)/FLASH.
3. When the number you want to dial is displayed, press
Basic Operation
Move a Number/Name to the Memory
1. Press . The screen displays DIRECTORY.
2. Press or
to scroll alphabetically through directory.
— OR —
Press the dial pad key for the first letter of the entry you want to move.
3. When the screen displays the entry you want to move, press SELECT. Then
press until SPEED flashes.
SPEED
EDIT
ERASE
8005959511
4. Press SELECT. The screen displays ENTER 1-9.
5. Press the key (1 through 9) to move this entry from the normal directory to the
speed dial memory and assign the memory location. You’ll hear a confirmation
beep. A memory location number (01 through 09) will be displayed with this
entry.
18
Caller ID Operation
Caller’s name
VTech
*
800-595-9511
5/01
5:40
PM
Date of call Time of call
OLD
28
Party has called
2 or more times
Caller’s telephone
number
Position of call in call
history
indicate whether the record
is new or old
Your ia 5829 can store up to 45 calls in its caller ID (CID) memory. The most
recent call will have the highest number. When the memory is full, the oldest call
will be deleted to make room for new incoming call information. For each call
that comes in, the screen displays the following information between the first
and second rings:
• Your caller’s name (up to 15 letters are sent by your telephone company).
• The caller’s area code and telephone number.
• The time and date of the call.
• The repeat tag (*) in the upper right corner, indicating the party has called
more than once.
If you answer a call before the information appears on the screen, it will not be
in the call history.
Review Call History
1. Press (CID) to view call history.
and to scroll through records in call history.
2. Use
NOTE: Press
(off) at any time to exit call history.
Delete Records from Call History
Delete a Specific Call:
1. Locate the record you want to delete from call history.
2. Press DELETE to delete. You’ll hear a confirmation beep.
Delete All Calls:
1. With the handset in idle (off) mode, press and hold DELETE to delete. The
screen displays ERASE ALL NO YES. The current choice flashes.
2. Press until YES flashes.
3. Press SELECT. You’ll hear a confirmation beep.
19
Basic Operation
About Call History (Caller ID)
Caller ID Operation
Dial a Displayed Number
1. Locate the record in call history that you want to dial.
2. If you wish to change how the number is dialed, press #. The screen displays
alternate dialing sequences available for this call (area code + number; 1 +
area code + number; number only; 1+ number).
3. Press SELECT. Press until DIAL flashes.
DIAL
PROGRAM
800-595-9511
5/01 5:40PM OLD 28
Basic Operation
4. Press SELECT again. The number is automatically dialed.
— OR —
(phone)/FLASH.
When the number is correctly displayed for dialing, press
Store a Call History Record in the Directory
1. Locate the record in the call history you want to store in the directory.
2. If you wish to change how the number is stored, press #. The screen displays
alternate dialing sequences available for this call (area code + number; 1 +
area code + number; number only; 1+ number).
3. Press SELECT, then press until PROGRAM flashes.
DIAL
PROGRAM
800-595-9511
5/01 5:40PM OLD 28
4. Press SELECT three times. The screen displays:
DISTINCT
RING?
N
8005959511
5/01 5:40PM OLD 28
5. Press or to select Y or N for distinctive ringer.
6. Press SELECT. You’ll hear a confirmation beep. If you choose Y in step 5 a
D will be displayed with the directory entry.
Display Screen Messages
Screen Displays:
When:
PRIVATE
The other party is blocking name and/or number
information.
UNKNOWN
Your phone company is unable to receive
information about this caller’s name and/or number.
* (after the name)
This caller has called you more than once.
20
Headset Operation
Your ia 5829 handset is equipped with a 2.5mm headset jack for use with an
optional accessory headset for handsfree operation. If you choose to use the
headset option, you must obtain an optional accessory headset, which is
compatible with the ia 5829.
To purchase a headset, visit us on the web at www. vtechphones.com or
call VTech Customer Service at 1-800-595-9511.
Once you have a compatible 2.5mm headset, locate the headset jack on the
ia 5829 handset. Connect the plug on the headset cord to the jack (under a
small rubber flap) on the cordless handset. The plug should fit securely. Do
not force the connection.
Belt Clip
The ia 5829 is also equipped with a
detachable belt clip. Align the pins on the
inside edge of the clip with the notches on
the sides of the handset. The belt clip
should snap securely into place. Do not
force the connection.
21
Additional Information
NOTE:
Whenever a compatible headset is
connected to the cordless handset, the
microphone on the handset will be muted.
This is done to limit the effect of background
noise.
Maintenance
Taking care of your telephone
Your cordless telephone contains sophisticated electronic parts, so it must be
treated with care.
Avoid rough treatment
Place the handset down gently. Save the original packing materials to protect your
telephone if you ever need to ship it.
Avoid water
Your telephone can be damaged if it gets wet. Do not use the handset outdoors in
the rain, or handle it with wet hands. Do not install your base unit near a sink, bathtub,
or shower.
Electrical storms
Electrical storms can sometimes cause power surges harmful to electronic equipment.
For your own safety, use caution when using electric appliances during storms.
Cleaning your telephone
Your telephone has a durable plastic casing that should retain its luster for many years.
Clean it only with a soft cloth slightly dampened with water or a mild soap. Do not
use excess water or cleaning solvents of any kind.
Additional Information
Remember that electrical appliances can cause serious injury if used when you
are wet or standing in water. If your base unit should fall into water, DO NOT
RETRIEVE IT UNTIL YOU UNPLUG THE POWER CORD AND TELEPHONE LINE
CORDS FROM THE WALL. Then pull the unit out by the unplugged cords.
22
In Case of Difficulty
If you have difficulty operating your phone, the suggestions below should solve the problem.
If you still have difficulty after trying these suggestions, visit us on the web at
www.vtechphones.com or call VTech Communications at 1-800-595-9511. In Canada,
call VTech Telecommunications Canada Ltd. at 1-800-267-7377.
The phone doesn't work at all
•
•
•
Make sure the power cord is plugged in.
Make sure the telephone line cord is plugged firmly into the base unit and the
telephone wall jack.
Make sure the batteries are properly charged. If you get a BATTERY LOW message
or indication, the battery needs charging.
No dial tone
•
•
First try all the suggestions above.
If you still don't hear a dial tone, disconnect the base unit from the telephone jack
and connect a different phone. If there is no dial tone on that phone either, the
problem is in your wiring or local service. Contact your local telephone company.
You get noise, static, or a weak signal even when you're near the base unit
•
Household appliances plugged into the same circuit as the base unit can sometimes
cause interference. Try moving the appliance or the base unit to another outlet.
You get noise, static, or a weak signal when you're away from the base
unit
•
•
You may be out of range. Either move closer to the base, or relocate the base
unit.
The layout of your home may be limiting the range. Try moving the base unit to
another position.
•
•
•
•
Make sure you have the ringer activated. Refer to the section on Handset Ringer
Style/Battery Save in this user's manual.
Make sure the telephone line cord is plugged firmly into the base unit and the
telephone jack. Make sure the power cord is plugged in.
You may be too far from the base unit.
You may have too many extension phones on your telephone line to allow all of
them to ring. Try unplugging some of the other phones.
You hear other calls while using your phone
•
Disconnect your base unit from the telephone jack, and plug in a regular telephone.
If you still hear other calls, the problem is probably in your wiring or local service.
Call your local telephone company.
23
Additional Information
The handset does not ring when you receive a call
In Case of Difficulty
You hear noise in the Handset, and none of the keys or buttons work
•
Make sure the power cord is plugged in.
Common cure for electronic equipment
Additional Information
If the unit does not seem to be responding normally, then try putting the handset in the
base. If it does not seem to respond, do the following (in the order listed):
1. Disconnect the power to the base.
2. Disconnect the handset battery, and spare battery, if applicable.
3. Wait a few minutes.
4. Connect power to the base.
5. Reinstall the battery(ies).
6. Wait for the handset to re-establish its link with the base. To be safe, allow up to
one minute for this to take place.
24
Warranty Statement
What does this limited warranty cover?
•
The manufacturer of this VTech product, VTech Communications, warrants to the
holder of a valid proof of purchase (“Consumer” or “you”) that the product and all
accessories provided by VTech in the sales package (“Product”) are free from
material defects in material and workmanship, pursuant to the following terms and
conditions, when installed and used normally and in accordance with operation
instructions. This limited warranty extends only to the Consumer for Products
purchased and used in the United States of America.
What will VTech Communications do if the Product is not free from material
defects in materials and workmanship during the limited warranty period
(“Materially Defective Product”)?
•
During the limited warranty period, VTech’s authorized service representative will
repair or replace at VTech’s option, without charge, a Materially Defective Product.
If we repair this product, we may use new or refurbished replacement parts. If
we choose to replace this product, we may replace it with a new or refurbished
product of the same or similar design. VTech will return repaired or replacement
products to you in working condition. VTech will retain defective parts, modules,
or equipment. Repair or replacement of Product, at VTech’s option, is your exclusive
remedy. You should expect the repair or replacement to take approximately 30 days.
How long is the limited warranty period?
•
The limited warranty period for the product extends for ONE (1) YEAR from the date
of purchase if we repair or replace a Materially Defective Product under the terms
of this limited warranty. This limited warranty also applies to repaired or replacement
Products for a period of either (a) 90 days from the date the repaired or replacement
Product is shipped to you or (b) the time remaining on the original one-year warranty;
whichever is longer.
This limited warranty does not cover:
1. Product that has been subjected to misuse, accident, shipping or other physical
damage, improper installation, abnormal operation or handling, neglect, inundation,
fire, water or other liquid intrusion; or
2. Product that has been damaged due to repair, alteration or modification by anyone
other than an authorized service representative of VTech; or
3. Product to the extent that the problem experienced is caused by signal conditions,
network reliability or cable or antenna systems; or
4. Product to the extent that the problem is caused by use with non-VTech electrical
accessories; or
5. Product whose warranty/quality stickers, Product serial numbers plates or electronic
serial numbers have been removed, altered or rendered illegible; or
6. Product purchased, used, serviced or shipped for repair from outside the United
States, or used for commercial or institutional purposes (including but not limited
to Products used for rental purposes); or
7. Product returned without valid proof of purchase (see 2 below); or
8. Charges for installation or set up, adjustment of customer controls and installation
or repair of systems outside the unit.
25
Additional Information
What is not covered by this limited warranty?
Warranty Statement
How do you get warranty service?
• To obtain warranty service in the United States of America, call 1-800-595-9511 for
instructions regarding where to return the Product. Before calling for service, please
check the user’s manual. A check of the Product controls and features may save
you a service call.
• Except as provided by applicable law, you assume the risk of loss or damage during
transit and transportation and are responsible for delivery or handling charges
incurred in the transport of Product(s) to the service location. VTech will return
repaired or replaced product under this limited warranty to you, transportation, delivery
or handling charges prepaid. VTech assumes no risk for damage or loss of the Product
in transit.
• If the Product failure is not covered by this limited warranty, or proof of purchase
does not meet the terms of this limited warranty, VTech will notify you and will request
that you authorize the cost of repair prior to any further repair activity. You must
pay for the cost of repair and return shipping costs for the repair of Products that
are not covered by this limited warranty.
What must you return with the Product to get warranty service?
1. Return the entire original package and contents including the Product to the VTech
service location along with a description of the malfunction or difficulty;
2. Include “valid proof of purchase” (sales receipt) identifying the Product purchased
(Product model) and the date of purchase or receipt; and
3. Provide your name, complete and correct mailing address, and telephone number.
Other Limitations
• This warranty is the complete and exclusive agreement between you and VTech.
It supersedes all other written or oral communications related to this Product. VTech
provides no other warranties for this product. The warranty exclusively describes
all of VTech’s responsibilities regarding the product.
There are no other express warranties. No one is authorized to make modifications
to this limited warranty and you should not rely on any such modification.
Additional Information
State Law Rights: This warranty gives you specific legal rights, and you may also
have other rights which vary from state to state.
Limitations: Implied warranties, including those of fitness for a particular purpose
and merchantability (an unwritten warranty that the product is fit for ordinary use)
are limited to one year from date of purchase. Some states do not allow limitations
on how long an implied warranty lasts, so the above limitation may not apply to you.
• In no event shall VTech be liable for any indirect, special, incidental, consequential,
or similar damages (including, but not limited to lost profits or revenue, inability to
use the product, or other associated equipment, the cost of substitute equipment,
and claims by third parties) resulting from the use of this product. Some states do
not allow the exclusion or limitation of incidental or consequential damages, so the
above limitation or exclusion may not apply to you.
26
FCC, ACTA and IC Regulations
This equipment complies with Parts 15 of the Federal Communications Commission
(FCC) rules for the United States. It also complies with regulations RSS210 and CS03 of Industry and Science Canada. Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired operation of the device.
A label is located on the underside of the Base Unit containing either the FCC registration
number and Ringer Equivalence Number (REN) or the IC registration number and Load
Number. You must, upon request, provide this information to your local telephone company.
This equipment is compatible with inductively coupled hearing aids.
Should you experience trouble with this telephone equipment, please contact:
VTech Communications Inc. CUSTOMER SERVICE at 1-800-595-9511. In Canada,
call VTech Telecommunications Canada Ltd. at 1-800-267-7377 for repair/
warranty information. The telephone company may ask you to disconnect this
equipment from the line network until the problem has been corrected.
FCC Part 15
Warning: Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user's authority to operate the equipment.
The equipment has been tested and found to comply with part 15 of the FCC rules.
These limits are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try and
correct the interference by one or more of the following measures:
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet or on a circuit different from that to which
the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
To ensure safety of users, the FCC has established criteria for the amount of radio
frequency energy that can be safely absorbed by a user or bystander according to the
intended usage of the product. This product has been tested and found to comply with
the FCC criteria. The handset has such a low power that it does not require testing. It
may be safely held against the ear of the user. The base unit shall be installed & used
such that parts of the user’s body other than the hands should be maintained at a
comfortable distance of approximately 20 cm or more.
FCC and ACTA Information
If this equipment was approved for connection to the telephone network prior to July
23, 2001, it complies with Part 68 of the Federal Communications Commission (FCC)
rules. If the equipment was approved after that date, it complies with the Part 68 rules
and with Technical Requirements for Connection of Equipment to the Telephone
Network adopted by the Administrative Council for Terminal Attachments (ACTA). We
are required to provide you with the following information.
27
Additional Information
•
•
•
FCC, ACTA and IC Regulations
1. Product identifier and REN information
The label on the back or bottom of this equipment contains, among other things, an
identifier indicating product approval and the Ringer Equivalence Number (REN). This
information must be provided to your local telephone company upon request. For
equipment approved prior to July 23, 2001, the product identifier is preceded by the
phrase “FCC Reg No.” and the REN is listed separately. For equipment approved after
that date, the product identifier is preceded by “US” and a colon (:), and the REN is
encoded in the product identifier without a decimal point as the sixth and seventh
characters following the colon. For example, the product identifier US:AAAEQ03T123XYZ
would indicate an REN of 0.3.
The REN is used to determine how many devices you may connect to your telephone
line and still have them ring when you are called. In most, but not all areas, the sum
of all RENs should be five (5.0) or less. For more information, please contact your local
telephone company.
2. Connection and use with the nationwide telephone network
The plug and jack used to connect this equipment to the premises wiring and the telephone
network must comply with the applicable Part 68 rules and technical requirements
adopted by ACTA. A compliant telephone cord and modular plug is provided with this
product. It is designed to be connected to a compatible modular jack that is also compliant.
An RJ11 jack should normally be used for connecting to a single line and an RJ14
jack for two lines. See Installation Instructions in this user’s manual. This equipment
may not be used with Coin Telephone Lines or with Party Lines. If you have specially
wired alarm dialing equipment connected to your telephone line, ensure the connection
of this equipment does not disable your alarm equipment. If you have questions about
what will disable alarm equipment, consult your telephone company or a qualified installer.
3. Repair instructions
If this equipment is malfunctioning, it must be unplugged from the modular jack until
the problem has been corrected. Repairs to this telephone equipment can only be made
by the manufacturer or its authorized agents. For repair procedures, follow the
instructions outlined under the Limited Warranty.
Additional Information
4. Rights of the telephone company
If this equipment is causing harm to the telephone network, the telephone company
may temporarily discontinue your telephone service. The telephone company is required
to notify you before interrupting service. If advance notice is not practical, you will be
notified as soon as possible. You will be given the opportunity to correct the problem
and the telephone company is required to inform you of your right to file a complaint
with the FCC. Your telephone company may make changes in its facilities, equipment,
operation, or procedures that could affect the proper functioning of this product. The
telephone company is required to notify you if such changes are planned.
5. Hearing aid compatibility
If this product is equipped with a corded or cordless handset, it is hearing aid compatible.
6. Programming/testing of emergency numbers
If this product has memory dialing locations, you may choose to store police, fire
department and emergency medical service telephone numbers in these locations. If
you do, please keep three things in mind:
a. We recommend that you also write the telephone number on the directory card,
so that you can still dial the emergency number manually if the memory dialing
28
FCC, ACTA and IC Regulations
feature doesn’t work.
b. This feature is provided only as a convenience, and the manufacturer assumes
no responsibility for customer reliance upon the memory feature.
c. Testing the emergency telephone numbers you have stored is not recommended.
However, if you do make a call to an emergency number:
• You must remain on the line and briefly explain the reason for the call before
hanging up.
• Programming/testing of emergency numbers should be performed during
off-peak hours, such as in the early morning or late evening, when the
emergency services tend to be less busy.
IC (Industry Canada)
This telephone is registered for use in Canada.
The term “IC:” before the radio certification number only signifies that Industry Canada
technical specifications were met.
Notice: This equipment meets the applicable Industry Canada Terminal Equipment
Technical Specifications. This is confirmed by the registration number. The abbreviation,
IC, before the registration number signifies that registration was performed based on
a Declaration of Conformity indicating that Industry Canada technical specifications were
met. It does not imply that Industry Canada approved the equipment.
Notice: The Ringer Equivalence Number (REN) for this terminal equipment is 0.1.
The REN assigned to each terminal equipment provides an indication of the maximum
number of terminals allowed to be connected to a telephone interface. The termination
on an interface may consist of any combination of devices subject only to the
requirement that the sum of the Ringer Equivalence Numbers of all the devices does
not exceed five.
Repairs to certified equipment should be made by an authorized Canadian maintenance facility designated by the Supplier. Any repairs or alterations made by the
user to this equipment, or equipment malfunctions, may give the telecommunications
company cause to request the user to disconnect the equipment.
Users should ensure for their own protection that the electrical ground connections
of the power utility, telephone lines and internal metallic water pipe system, if present,
are connected together. This precaution may be particularly important in rural areas.
Caution: Users should not attempt to make such connections themselves, but should
contact the appropriate electrical inspection authority or electrician as appropriate.
Your Cordless Phone is designed to operate
FCC and IC. This means your Handset and
a certain distance - which will depend on the
weather, and the construction and layout of
29
at the maximum power allowed by the
Base Unit can communicate only over
location of the Base Unit and Handset,
your home or office.
Additional Information
Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local telecommunications company. The equipment must
also be installed using an acceptable method of connection. The customer should be
aware that compliance with the above conditions may not prevent degradation of services in some situations.
Technical Specifications
FREQUENCY CONTROL
WEIGHT
Crystal controlled
PLL synthesizer
Handset: 159g (without battery
pack)
TRANSMIT FREQUENCY
Base: 205 gram(without adaptor
and wallmount)
Base:
912.75 - 917.10 MHz
Handset: 5863.80 - 5872.50 MHz
POWER REQUIREMENTS
RECEIVE FREQUENCY
Base: 5863.80 - 5872.50 MHz
Handset: 912.75 - 917.10 MHz
CHANNELS
3.6V 600mAh Ni-MH
Battery
Base:
9V DC @ 300mA
MEMORY
30 Channels
NOMINAL
RANGE
Handset:
Speed Dial: 9 Memory locations;
up to 24 digits, 15
characters per
location
EFFECTIVE
Maximum power allowed by FCC
and IC. Actual operating range
may vary according to environmental
conditions at the time of use.
Directory:
SIZE
Handset: 193mm x 58mm x 36.7mm
CID:
20 Memory locations;
up to 24 digits, 15
characters
per
location
45 Memory locations
Additional Information
Base: 182mm x 113mm x 88.3mm
SPECIFICATIONS ARE TYPICAL
AND MAY CHANGE WITHOUT
NOTICE.
30
VTECH TELECOMMUNICATIONS LTD.
A member of THE VTECH GROUP OF COMPANIES.
Distributed in the U.S.A. by VTech Communications, Inc. Beaverton,
Oregon, 97008
Distributed in Canada by VTech Telecommunications Canada Ltd. 200-7671
Alderbridge Way, Richmond, B.C. V6X 1Z9.
Copyright 2004 for VTECH TELECOMMUNICATIONS LTD.
Printed in China
91-000175-010-000
ISSUED 0
Congratulations on your purchase
of this VTech product
NEED HELP?
Our representatives are here
to help you with any questions
concerning the operation of this
product, available accessories,
or any other related issues.
Call Toll Free:
1-800-595-9511
In Canada, Call:
1-800-267-7377
or visit our website at
www. vtechphones. com
CORDLESS Troubleshooting TAGS
250 De-register and register
De-register handset from the E2525, E2600B and E2555
Please take the Handset out of the Base before de-registering. Using the [SOFT] Keys on
the Base, press MENU, then press the Down arrow twice until BASE SETTINGS is
highlighted. Press OK, then press MUTE 3 times and FLASH twice. This will deregister
the unit, please see more info to re-register.
Adding Handsets / Registering Handsets
Your telephone can accommodate up to 8 cordless Handsets. You can add new Handsets
(Model E250, sold separately) at any time, but each must be registered with the Base
before use.
Before using a new Handset, you must register it with the Base. There will be an R in the
upper left hand corner of the display. The Display will read "ENTER BASE ID". Use the
keypad on the Handset to enter Base ID. (To find this number, go to the Base, press
[MENU], scroll down to select DISPLAY BASE ID, then press OK.) Once you have
entered the Base ID number, press OK (middle key under the display). The unit will
display "SEARCHING FOR BASE" and then "FOUND BASE". Your Handset will then
be ready to use.
The Handset provided with your telephone is automatically registered as Handset 1.
Additional Handsets will be assigned numbers in the order the are registered (2, 3, 4, etc.)
up to a maximum of eight.
De-register 250 from the E2520 Base
Take the Handset out of the Base, press [*] [*] [3] [3] [5] [7] [8] [2] on the Base. This
will de-register all of the Handsets at one time. See more information to register them
again.
NOTE: The Base ID code is located on the bottom of the Base.
Adding new Handsets / registering the Handset
Your telephone can accommodate up to 8 cordless Handsets. You can add new Handsets
(Model E250, sold separately) at any time, but each must be registered with the Base
before use.
Before using a new Handset, you must register it with the Base. There will be an R in the
upper left hand corner of the Display. The Display will read "ENTER BASE ID". Use the
keypad on the Handset to enter the Base ID. (To find this number, go to the Base, on the
bottom of the Base will be a white sticker that reads BS ID CODE. The code will start
with a 36. Once you have entered the Base ID number, press OK (middle key under the
display). The unit will display "SEARCHING FOR BASE" and then "FOUND BASE".
Your Handset will then be ready to use.
The Handset provided with your telephone is automatically registered as Handset 1.
Additional Handsets will be assigned numbers in the order the are registered (2, 3, 4, etc.)
up to a maximum of eight.
Keypad Tone Feature - Vtech Telephones
When the Keypad Tone Feature is ON but the handset is OFF (i.e. in standby):
You will hear loud tones being emitted through the external speaker on the back of the
handset when you press any handset button except for the volume key.
When the Keypad Tone Feature is ON and the handset is ON (i.e. you pressed the
[PHONE] button to make a call, you have dial tone and you are NOT on the
Speakerphone):
1.You will hear the tones from the number buttons ([0] - [9]), the asterisk ([*]), the pound
([#]), and the [SOUND SELECT] button ONLY through the earpiece on the handset (the
receiver / internal speaker).
a) The earpiece on the handset (the receiver / internal speaker) is where you hear the dial
tone. The above key tones will have the same approximate volume as the dial tone.
b) You WILL NOT hear these tones loudly through the external speaker on the back of
the handset.
2.You will hear the loud tones from the [PHONE/FLASH] button, the [OFF] button, the
[SOFTKEY] buttons ( the 2 unnamed buttons under the display), and the [SPEAKER]
button being emitted through the external speaker located on the back of the handset.
When the Keypad Tone Feature is OFF and the handset is OFF (i.e. in standby):
You will not hear any key tones from any handset buttons.
When the Keypad Tone Feature is OFF and the handset is ON (i.e. you have pressed the
[PHONE] button to make a call, you have dial tone and you are NOT on the
Speakerphone):
1.You WILL hear the tones from the number buttons ([0] - [9]), the asterisk ([*]), the
pound ([#]), and the [SOUND SELECT] button through the earpiece on the handset (the
receiver/internal speaker). This is NORMAL operation.
a) The above key tones will have the same approximate volume as the dial tone.
b) You WILL NOT hear these tones being emitted through the external speaker located
on the back of the handset.
c) You will not hear any tones from the [SOFTKEY] buttons (the two unnamed buttons
under the display), or the [SPEAKER] button.
When the Keypad Tone Feature is OFF and the Speakerphone on the handset is ON:
1.You WILL hear the tones from the number buttons ([0] - [9]) emitted through the
external speaker on the back of the handset.
a) When the speakerphone is on, this is also where you hear the dial tone emitted.
b) The above key tones will have the same approximate sound and volume as the dial
tone.
2.You will not hear any tones from the [SOUND SELECT] button, the [SOFTKEY]
buttons (the two unnamed buttons under the display), or the [SPEAKER] button.
When the Keypad Tone Feature is ON and the Speakerphone on the handset is ON:
1.You will hear the tones from the number buttons ([0] - [9]), the [SOFTKEY] buttons
(the two unnamed buttons under the display), the [SPEAKER] button, the [PHONE]
button, and the [OFF] button emitted through the external speaker on the back of the
handset.
2.You will not hear any tone when you press the [SOUND SELECT] button.
Keypad Tone Feature
When the Keypad Tone Feature is ON but the handset is OFF (i.e. in standby):
You will hear loud tones being emitted through the external speaker on the back of the
handset when you press any handset button except for the volume key.
When the Keypad Tone Feature is ON and the handset is ON (i.e. you pressed the
[PHONE] button to make a call, you have dial tone and you are NOT on the
Speakerphone):
1.You will hear the tones from the number buttons ([0] - [9]), the asterisk ([*]), the pound
([#]), and the [SOUND SELECT] button ONLY through the earpiece on the handset (the
receiver / internal speaker).
a) The earpiece on the handset (the receiver / internal speaker) is where you hear the dial
tone. The above key tones will have the same approximate volume as the dial tone.
b) You WILL NOT hear these tones loudly through the external speaker on the back of
the handset.
2.You will hear the loud tones from the [PHONE/FLASH] button, the [OFF] button, the
[SOFTKEY] buttons ( the 3 unnamed buttons under the display), the
[XFER/INTERCOM] button and the [SPEAKER] button being emitted through the
external speaker located on the back of the handset.
When the Keypad Tone Feature is OFF and the handset is OFF (i.e. in standby):
You will not hear any key tones from any handset buttons.
When the Keypad Tone Feature is OFF and the handset is ON (i.e. you have pressed the
[PHONE] button to make a call, you have dial tone and you are NOT on the
Speakerphone):
1.You WILL hear the tones from the number buttons ([0] - [9]), the asterisk ([*]), the
pound ([#]), and the [SOUND SELECT] button through the earpiece on the handset (the
receiver/internal speaker). This is NORMAL operation.
a) The above key tones will have the same approximate volume as the dial tone.
b) You WILL NOT hear these tones being emitted through the external speaker located
on the back of the handset.
c) You will not hear any tones from the [SOFTKEY] buttons (the three unnamed buttons
under the display), the [XFER/INTERCOM] button or the [SPEAKER] button.
When the Keypad Tone Feature is OFF and the Speakerphone on the handset is ON:
1.You WILL hear the tones from the number buttons ([0] - [9]) emitted through the
external speaker on the back of the handset.
a) When the speakerphone is on, this is also where you hear the dial tone emitted.
b) The above key tones will have the same approximate sound and volume as the dial
tone.
2.You will not hear any tones from the [SOUND SELECT] button, the [SOFTKEY]
buttons (the three unnamed buttons under the display), the [XFER/INTERCOM] button,
or the [SPEAKER] button.
When the Keypad Tone Feature is ON and the Speakerphone on the handset is ON:
1.You will hear the tones from the number buttons ([0] - [9]), the [SOFTKEY] buttons
(the three unnamed buttons under the display), the [XFER/INTERCOM] button, the
[SPEAKER] button, the [PHONE] button, and the [OFF] button emitted through the
external speaker on the back of the handset.
2.You will not hear any tone when you press the [SOUND SELECT] button.
5860 Ringer On/Melody Selection
Turn Ringer On
1.Press any [NavKey] button to get to the Handset Menu.
2.Press the left, right, up or down [NavKey] button to highlight Sounds and Alerts
(handset with musical note icon), then press the center [NavKey] button to select.
3.Press the left, right, up or down [NavKey] to highlight Ringer Control (the bell icon),
then press the center NavKey button to select.
4.Press the down [NavKey] button to highlight RINGER.
5.Press the left or right [NavKey] button to change the ringer status from Off to On.
6.Press the [SOFT] Key under SAVE.
Choose Ringer Melodies
1.Press any [NavKey] button to get to the Handset Menu.
2.Press the left, right, up or down [NavKey] button to highlight Sounds and Alerts
(handset with musical note icon), then press the center [NavKey] button to select.
3.Press the left, right, up or down [NavKey] to highlight Ringers (the musical note icon),
then press the center [NavKey] button to select.
4.Press the up or down [NavKey] button to highlight the different melodies. You will
hear a sample of the melody you have highlighted.
5.Press the [SOFT] Key under SAVE when you have chosen the melody you want.
Adjust Ringer Volume
1.Press any [NavKey] button to get to the Handset Menu.
2.Press the left, right, up or down [NavKey] button to highlight Sounds and Alerts
(handset with musical note icon), then press the center [NavKey] button to select.
3.Press the left, right, up or down [NavKey] button to highlight RINGER CONTROL
(the bell icon), then press the center button of the [NavKey] to select.
4.Press the left or right [NavKey] button to select the volume level. With each press of
the button a sample of the volume is played.
5.Press the [SOFT] Key under SAVE.
To access the complete owner's manual. Click on the Red Top icon (located in the upper
right hand corner of this page).
2256/1256 - 2325/2365 Replace
This process is only to be used for the models 2256/1256, 2325, 2365 on the symptoms
below:
·Every call customer hears pause in conversation, other end hears beeps.
·Every call conversation cuts in and out, other end hears beeps.
1.Advise the customer that you (the rep) will place a no charge replacement order that
will be shipped via UPS service, which should arrive within 14 days. Advise the
customer that they will also receive a prepaid ARS label sent via US Mail to return their
original unit (no charge will be incurred by the customer).
2.The rep will be responsible for placing the order for the unit using the EXCHANGE­
IW promo code in COPS and changing the shipping method to Free Shipping.
3.After placing the order, send an internal referral commitment to the [AAT ARS
LABEL] team.
If you have any questions regarding this information, please see your supervisor. It is
very important that every one understands this process and begins using it immediately.
NOTE: THE CUSTOMER MAY RECEIVE A 2256 FOR A 1256. THE TWO MODELS
ARE IDENTICAL.
NOTE: THE CUSTOMER MAY RECEIVE A 2325 FOR A 2365. THE TWO MODELS
ARE IDENTICAL.
T-Switch
A standard hearing aid consists of a high gain amplifier between a microphone and
receiver. If you put a cup over the ear such as a telephone handset, there is serious
feedback and squealing. The remedy is to add a "T-Switch" in the hearing aid that
disconnects the microphone and replaces it with a coil of wire. The phone receiver also
has a coil of wire (HAC coil), and so these two coils form a transformer when they are in
close proximity. Transformers transmit the signal magnetically rather than acoustically.
The T-Coil in the hearing aid picks up any magnetic energy in close proximity. Spread
spectrum phones produce a magnetic field when the RF transmitter turns on and off
repeatedly. This magnetic energy can be picked up as static or hum in a hearing aid, but
is usually a much lower level than the intended audio transmitted from the HAC coil.
Generally, non-spread spectrum phones will perform better with hearing aids.
process for T2406 calls
If the customer has had his or her unit longer than 45 days:
1. Advise the customer to mail his or her entire product to the San Antonio Returns
Center using the normal in warranty repair shipping and return process.
2. Advise the customer that upon receiving his or her telephone product at our San
Antonio Returns Center, he or she will receive a similar or upgraded replacement model
within 3 business days.
If the customer has had his or her unit less than 45 days or refuses to pay shipping costs
to return their product for in warranty service:
Do not send the customer back to the retailer. Offer to issue a replacement order and
send a prepaid ARS label via US Mail for him or her to ship their original product back at
no charge to them.
· If this is the case, it will be necessary for you to place an order for the VTech T2406
using the EXCHANGE-IW promo code in COPS and use regular standard shipping. (The
customer will receive the replacement within 3-Business days.)
· After placing the order, send an internal referral commitment to the [VTECH ARS
LABEL] team for a prepaid UPS ARS Label to be sent to the customer.
NOTE: DO NOT SEND THESE CUSTOMERS BACK TO THE RETAILER FOR
REPLACEMENT (EVEN IF THEY ARE WITHIN THE FIRST 30 DAYS OF
PURCHASE). IT IS IMPORTANT THAT YOU FOLLOW THIS PROCESS.
Process for gz2434 Calls
If customers call with the one or more of the following symptoms: Static/Noise; Five
Beeps; Call is Fading or Cutting In and Out; No Connect and the final resolution is
repair, follow the below steps:
1.Advise the customer that you will place a no charge replacement order that will be
shipped via express service, which should arrive within 1-3 business days. Advise the
customer that they will also receive a prepaid UPS ARS label sent via US Mail to return
their original unit (no charges will be incurred by the customer).
2.You will need to place a no charge replacement order for the VTech GZ2434 using the
CSAT promotion code in COPS and change the shipping method to Free ShippingOvernight (manager use only) $0.
3.After placing the order, it will be necessary to send an internal referral commitment to
the [VTECH ARS LABEL] team requesting an ARS label be sent to the customer.
If the customer is not satisfied with the express shipped replacement, offer to extend their
manufacture's warranty for 6 months (this is different than a Protection Plan; Protection
Plans should never be given out as a negotiation method).
Turning Message Light Off
If the Message Light on the Base does not go off even after you've listened to voice mail
messages:
1.Press [PROG/CHAN].
2.Press [>] until the screen displays: MESSAGES WAITING.
3.Press [SELECT]. The screen displays: LIGHTS OFF: YES.
4.Press [SELECT] again to turn off the Message Waiting Light on Base.
2600 De-Register
2600 registered to a 2651
·In the idle mode, at the Base Unit keypad, press [*] [*] [3] [3] [5] [7] [8] [2].
2600 registered to a 2656 or 2670
·Unplug power from the Base.
·Hold down [PAGE] while reconnecting power. When the In Use Light blinks, release the
[PAGE] key.
·Hold down [PAGE] for 5 seconds. When the In Use Light begins to flash, release the
[PAGE] key.
·The Handset Charging Light will blink 5 times. Within 5 seconds from when it stops
blinking, press [PAGE] once
Registration of the 2600
·After charging the Handset, remove it from its Charge Cradle. If the screen displays
SEARCHING FOR BASE, Press NEW. If the screen displays ENTER BASE ID, go to
step 2.
·Enter the 15 digit Base ID Code, located on the underside of the Base Unit. The ID Code
can include numbers (0-9) and characters (*,#).
·Press OK. The Handset will display: PLEASE WAIT!
·Wait approximately 15 seconds. The Handset will display FOUND BASE.
NOTE: Occasionally, it will take longer than 15 seconds for the Handset to find the Base
Unit. This is normal.
If the Handset displays: BASE BUSY TRY LATER, this indicates that the system is in
use. Wait until the Base Unit is in the idle (on hook) mode, and repeat steps 2 to 4.
Explanation of Why the TeleZapper Should Be Set On
'BASIC' to avoid interference with an Answering System
Once the Answering System picks up the line, the TeleZapper also seizes the line and
generates the tones which 'zap' telemarketers. When the TeleZapper is in 'advanced'
mode, the tones can stay on the line long enough that the Answering System may think
that an extension phone has been picked up (depending on the Answering System). If this
happens, the Answering System's Call Intercept/Interrupt feature will stop the recording
of the message, and since no extension has actually been picked up, the call will be
disconnected.
Twisted Pair Cords
Twisted pair cords are a type of phone cord wires used to reduce interference/crosstalk
between lines. Twisted pair cords consist of two insulated copper wires which are twisted
around each other to reduce interference from one wire to the other. The twisting of the
wire pairs is what reduces the interference.
Dual-Band Frequency
Our unit does utilize both the 5.8 and 2.4 GHz frequency bands simultaneously. The
dual-band technology provides a clear advantage over existing cordless phones in its
ability to avoid interference and provide optimal clarity in both received and transmitted
audio.
Since transmitting in the 5.8 GHz frequency requires more power, the Base station
transmits with the 5.8 GHz band (since it remains plugged to a power outlet all the time),
while the battery-operated Handset transmits in the 2.4 GHz band, so it can yield
optimum talk-time performance between battery charges.
Language Conversion
VT5831 LANGUAGE CONVERSION OF HANDSET MENUS
ENGLISH
SPANISH
FRENCH
CALLS LOG
GUIA DE LLAMADAS
REGISTRE D'APPEL
INTERCOM
INTERCOMUNICADOR
INTERPHONE
HANDSET SETTINGS
CONFIG AURICULAR
REGLAGES COMBINE
SET TIME
PONER TIEMPO
REGLER L'HEURE
CLOCK MODE
MODO RELOJ
MODE HORLOGE
REGISTER
REGISTRAR
REGISTRE
RINGER VOLUME
TIMBRE VOLUMEN
SONNERIE VOLUME
RINGER MELODY
TIPO DE TIMBRE
SONNERIE MELODIE
VIBRATE CONTROL
CTRL VIBRACION
MODE VIBRATION
LOW BATT TONE
TONO DE BAT BAJA
SON PILE FAIBLE
RANGE TONE
TONO DE RANGO
SON DE PORTEE
KEYPAD TONE
TONO DE DECLADO
SON DU CLAVIER
CONTRAST
CONTRASTE
CONTRASTE
LANGUAGE
IDIOMA
LANGUE
TO CHANGE HANDSET MENU FROM SPANISH:
Press MENU.
Scroll down to CONFIG AURICULAR. Press OK.
Scroll down to IDIOMA. Press OK.
Scroll up to INGLES (English) or scroll down to FRANCES (French). Press OK.
TO CHANGE HANDSET MENU FROM FRENCH:
Press MENU.
Scroll down to REGLAGES COMBINE. Press OK.
Scroll down to LANGUE. Press OK.
Scroll up to ANGLAIS (English) or ESPAGNOLE (Spanish). Press OK.
LANGUAGE CONVERSION OF BASE MENUS
ENGLISH
SPANISH
FRENCH
CALLS LOG
GUEA DE LLAMADAS
REGISTRE D'APPEL
BASE SETTINGS
CONFIG BASE
REGLAGES BASE
DISPLAY BASE-ID
NUMERO DE BASE
NUMERO DE BASE
RINGER VOLUME
TIMBRE VOLUMEN
SONNERIE VOLUME
RINGER MELODY
TIPO DE TIMBRE
SONNERIE MELODIE
KEYPAD TONE
TONO DE DECLADO
SON DU CLAVIER
TONE/PULSE
TONOS/PULSOS
TONALITE/IMPUL
CONTRAST
CONTRASTE
CONTRASTE
LANGUAGE
IDIOMA
LANGUE
TO CHANGE BASE MENU FROM SPANISH:
Press MENU.
Scroll down to CONFIG BASE. Press OK.
Scroll down to IDIOMA. Press OK.
Scroll up to INGLES (English) or scroll down to FRANCES (French). Press OK.
TO CHANGE BASE MENU FROM FRENCH:
Press MENU.
Scroll down to REGLAGES BASE. Press OK.
Scroll down to LANGUE. Press OK.
Scroll up to ANGLAIS (English) or ESPAGNOL (Spanish). Press OK.
2461 De-register
There are 2 different versions of this unit. If the customer has a tone/pulse switch on the
bottom of the Base, please use on of the procedures for Mk1. If they do not have a
tone/pulse switch on the bottom of the set, please use the procedure for Mk2a.
VT2461 Mk1 DEREGISTER ALL HANDSETS
1.Unplug power from the Base. Remove spare battery pack.
2.Hold down [PAGE] while reconnecting power. When the POWER light begins to
blink, release the [PAGE] key.
3.Hold down [PAGE] key for 5 seconds. When the LINE IN USE light begins to flash,
release the [PAGE] key.
4.The HANDSET CHARGING light will blink 5 times. Within 5 seconds from when it
stops blinking, press [PAGE] once.
VT2461 Mk1 DEREGISTER A SINGLE HANDSET
1.Unplug power from the Base. Remove spare battery pack.
2.Hold down [PAGE] while reconnecting power. When the POWER light begins to
blink, release the [PAGE] key.
3.Press [PAGE] 1 to 4 times, corresponding to the Handset you wish to deregister.
4.Once you complete step #3, the HANDSET CHARGING light will blink back to you
the number of times corresponding to the Handset you wish to deregister. Within 5
seconds from when it stops blinking, press [PAGE] once.
VT2461 Mk2a
1.Unplug power from the Base. Remove spare battery pack.
2.Hold down [PAGE] while reconnecting power. When the Base Display says 'Pr',
release [PAGE].
3.Press [MENU]. The Display will say 'rh'.
4.Press [SELECT] to choose h1, h2, h3, h4 or AL (all).
5.Press [TIME/SET] to confirm.
Unplug power from the Base, then reconnect power to complete deregistration.
2455 De-register
DEREGISTER ALL HANDSETS
1.Unplug power from the Base. Remove spare battery pack.
2.Hold down [PAGE] while reconnecting power. When the POWER light begins to
blink, release the [PAGE] key.
3.Hold down [PAGE] for 5 seconds. When the LINE IN USE light begins to flash,
release the [PAGE] key.
4.The HANDSET CHARGING light will blink 5 times. Within 5 seconds from when it
stops blinking, press [PAGE] once.
DEREGISTER A SINGLE HANDSET
1.Unplug power from the Base. Remove spare battery pack.
2.Hold down [PAGE] while reconnecting power. When the POWER light begins to
blink, release the [PAGE] key.
3.Press [PAGE] 1 to 4 times, corresponding to the Handset you wish to deregister.
4.Once you complete step #3, the HANDSET CHARGING light will blink back to you
the number of times corresponding to the Handset you wish to deregister. Within 5
seconds from when it stops blinking, press [PAGE] once.
8 inch 4 conductor line cord
Perform the following:
-Advise the customer that we will send him a replacement 8 inch 4 conductor line cord.
-Inform the customer that he or she will receive the new replacement cord in U.S. Mail.
-Verify and update the customer's profile with all address and telephone information.
-Place an internal referral request via CRSS to Research Advisor to place an order for the
replacement line cord.
Perform the following:
- Advise the customer that you are sending him or her a brand new replacement set
(Cordless 2230 or 2255 whichever the customer has). If the customer does not want the
replacement, advise him or her to return their unit to the place of purchase. Stop! If the
customer accepts the replacement 2230/2255 continue....
- Inform the customer that he or she will receive the new replacement set(s) within 14
business days. Explain that you will also send an ARS label (via US Mail) for him or
her to return his or her original unit.
- Verify and update the customer's profile with all address and telephone information.
- Access DES and enter a replacement order for the customer.
- You will then need to place another commitment (via the internal referral team [OSG-to
place an SAP order]) requesting an ARS Label be sent to the customer.
Deregistration process for V2421
1.If base is plugged in, disconnect the DC connector from it and wait at least 10 seconds
before proceeding.
2.Hold down the [PAGE] button while reconnecting the DC cord to the base. Continue
to hold down the [PAGE] button for 5 seconds after reconnecting power.
3.Release the [PAGE] button.
4.Press the [PAGE] button from 1 to 5 times, depending on the handsets you wish to
deregister:
1 press deletes HS1: 2 presses deletes HS2; etc. 5 presses deletes all.
The Base LED will flash with each key press.
5.After entering the handset(s) to delete, the base will flash back the number of key
presses entered.
6.Once the LED stops flashing, press [PAGE] once. Your mission is complete.
Access to SoundCard
Access to SoundCard
1.Press start
2.Programs
3.Accessories
4.Entertainment/multimedia
5.Volume control ( this will open the master volume control)
6.Go to Options and select Properties
Select Line In
1.Press start
2.Programs
3.Accessories
4.Entertainment/multimedia
5.Volume control ( this will open the master volume control)
6.Go to Options and select Properties
7.There will be an option to adjust Recording or playback volume control. Choose
Recording.
8.There is another section under recording where you pick which volume controls you
want to show on the bar. Make sure there is a check next to "line". If there is not, please
check it
9.Hit "Ok". Now "line or Line In" should show up in the master volume control for
Recording. Please make sure that there is a check mark in the Select box under the "Line
or Line IN
10.Go to Options and Select Properties.
11.There should be an option to adjust Recording or playback volume control. Choose
Playback.
12.There is another section under playback where you pick which volume controls you
want to show on the bar. Make sure there is a check next to "line or Line in". If there is
not, please check it.
13.Hit "Ok". Now "line or Line in " should show up in the master volume control for
Playback. Please make sure that there is a check mark in the MUTE box under the "line
or line in". (it is possible that you may not have a MUTE option, it might be "SELECT".
If you have a choice to SELECT then do not check SELECT under LINE")
14.Now close the Master Volume Control.
Operating Range General
This cordless telephone operates within the maximum power allowed by the Federal
Communications Commission (FCC). Even so, this handset and base can communicate
over only a certain distance --- which can vary with the locations of the base and handset,
the weather, and the construction of your home or office. For best performance, keep the
base antenna fully upright.
If you receive a call while you are out of range, the handset might not ring --- or if it does
ring, the call might not connect when you press [PHONE]. Move closer to the base, then
press [PHONE] to answer the call.
If you move out of range during a phone conversation, you might hear noise or
interference. To improve reception, move closer to the base.
If you move out range without pressing[OFF], your phone will be left "off the hook." To
hang up properly, walk back into range, periodically pressing [OFF].
Handset De-Registration (2455/2461)
1.Disconnect power to the Base (either unplug the DC connector from the bottom of the
Base or unplug the power supply from the outlet). Remove spare battery, if applicable.
2.Hold down the base PAGE key while applying power back to the Base. When the
POWER LED begins to blink, release the PAGE key.
THE USER HAS 15 SECONDS TO BEGIN THE NEXT STEP;OTHERWISE, THE
BASE WILL EXIT PROGRAM MODE.
3.Hold down the PAGE key for 5 seconds. The HANDSET CHARGING LED will be
lit, and after 5 seconds, the LINE IN USE LED will start to flash. Now release the PAGE
key.
4.The HANDSET CHARGING LED will blink 5 times and then go out. Within 5
seconds from when it stops blinking, press and release the PAGE key.
All handsets should now be deregistered.
Conference calls
When call is conferenced, two lines are being bridged through one telephone. The normal
loss that occurs between a station to station call is doubled when using the conference
call feature. The quality of transmission depends on many variables including the amount
of line voltage available at the phone and the distance of miles between the two other
parties. Customer may consider 3-way calling service (if available through local telco) as
alternative. Customer is less likely to experience volume loss due to more direct routing
of conference.
Caller Id after 2nd ring
Most Telco's send out the Caller ID information between the 1st and 2nd ring. Some
Telco's send out this information later. If the machine answers the call before the
information is received, the Caller ID information will be lost. Please set the number of
rings to a number higher than 2. The customer may want to turn the machine off and
then let a call come in to see when the information arrives. You need to set the answering
system to answer the ring after the caller ID information arrives. Do not set it for the
same ring. If you have voice mail service, set it to answer at 6 rings.
Operating Range 2.4
This cordless operates in the 2.4 Gigahertz frequency band. Radio signals in this band
can penetrate small openings and reflect around obstructions more effciently than those
of conventional cordless telephones. This alows the unit to operate in areas that are
typically difficult for cordless phones.
Your cordless telephone operates at the maximum power allowed by the Federal
Communications Commission (FCC). Even so, your handset and base can communicate
only over a certain distance which can vary with the locations of the base and handset,
the weather, and the construction of your home or office.
Spread Spectrum Echo
This unit employs state-of-the-art frequency hopping spread spectrum (FHSS) technology
to achieve one of the longest ranges in the consumer cordless telephone industry. FHSS
is a digital technology that is also found in much more expensive cellular telephones.
Just as it is common to experience echo in some cellular telephone systems, some users
will experience occasional echo while using this phone. The presence and/or level of
echo will depend on the electrical characteristics of the connection between the phone
and user's local central office. This is normal operation. The customer can lower the
volume on the handset and this will decrease the echo.
Caller ID/Call Waiting Services
It may not be enough that the users subscribe to both services, they may also need to ask
the local phone company to combine Caller ID with Call Waiting, so that their Caller ID
product will be able to recognize names and numbers for a Call Waiting call, as well as,
for regular calls. There may be an additional charge for this combined feature. Their
phone company may use names for this combined feature that are not on this list, but
listed below are some of the more generally used names for this combined Caller ID with
Call Waiting service:
·Call Waiting ID, Caller ID/Call Waiting ID - Bell Atlantic
·Wait and See - Ameritech
·Call Waiting ID - PacBell, SW Bell
·Caller ID with Name on Call Waiting - SNET
in.
Operating Range 900
This cordless operates in the 900 megahertz frequency band. Radio signals in this band
can penetrate small openings and reflect around obstructions more effciently than those
of conventional cordless telephones. This alows the unit to operate in areas that are
typically difficult for cordless phones.
Your cordless telephone operates at the maximum power allowed by the Federal
Communications Commission (FCC). Even so, your handset and base can communicate
only over a certain distance which can vary with the locations of the base and handset,
the weather, and the construction of your home or office.
Cardiac Pacemakers
THE FOLLOWING INFORMATION IS LOCATED AT THE BEGINNING OF THE
CIB
Cardiac Pacemakers (applies only to 900 MHz Digital Cordless Telephones):
Preliminary studies performed at the U.S.. Food and Drug Administration (FDA) and
elsewhere have shown that when digital wireless telephones using technology similar to
900 MHz Cordless Telephones are placed very close to implanted cardiac pacemakers,
interference with the operation of the pacemaker can occur. These preliminary studies
show that interference is not likely to occur when there is a reasonable distance between
the telephone and the implanted pacemaker and stops when the phone is set in the
"battery save mode" or moved so that it is more than 3 inches from the pacemaker.
Based on these preliminary studies, the FDA has concluded that digital wireless
telephones "do not seem to pose a significant problem for pacemaker wearers.
Until more is known, the FDA suggests that people with pacemakers may want to take
some simple precautions when using or carrying digital wireless telephones to ensure that
there is ample distance between the digital cellular telephone and the pacemaker -- by not
placing the phone next to the pacemaker implant (for example, in a shirt or coat pocket
directly over the pacemaker implant) when the phone is turned on ready to receive a call
and holding it to the ear opposite the side of the body where the pacemaker is implanted
when using the phone. Consult your physician or medical device manufacturer to
determine if additional precautions are necessary.
Volume Controls
Both the base unit and the handset have digital volume controls. The volume controls for
the speakerphone are located on the front face of the base unit. Press the volume up side
to increase the speaker volume and the volume down side to decrease the volume.
Holding either side down will continuously change the volume setting.
The volume controls for the handset are located on the side of the unit. Press the [^] (up)
or [v] (down) keys to increase or decrease the volume.
Date Code Sticker
The date code sticker can be found inside the handset battery compartment, on the bottom
of the base, or on the pretty box. It specifically indicates where and when the product
was manufactured.
Following is an example of what is shown on the sticker:
940101 B
2/7
CPS 2A
Note: If inputting the date code in the FCC field, use the following format:
940101B2-7CPS2A (CRS will not accept a slash.)
The battery save feature will deactivate the ring approximately 60 seconds after being set.
After 60 seconds, the phone will enter "sleep mode". The phone will not ring or display
"incoming call" when the extension phones are ringing. If any button on the phone is
pressed, this will "wake up" the phone. If there is an incoming call within 60 seconds of
a button being pressed, the phone will ring. Once nothing has been pressed for another
60 seconds, the phone will go back into "sleep mode" and will not ring.
ToneLength
Tone length for most cordless telephones is 80-100 milliseconds.
Some services may require longer tones. You need to look for a phone that will continue
to produce a tone signal for as long as a digit is held down. We have many phones with
long tones.
Handset Warmth
It is normal to feel heat near the battery compartment on the cordless handset once the
battery has been fully charged. There is a component in the battery known as a
"separator" which converts excess energy to heat.
Relocate Phone In Home EMI + Sep/Phns
Interference generated by some radio equipment and electrical appliances and machinery
may travel through the air, affecting other types of equipment in close proximity.
Filters cannot help in this situation. Separating the objects may be the only solution.
Split Line w/Triplex + Verify 2 cond cord on line 1
If single line telephone equipment is also experiencing crosstalk, the customer may try
the following remedies:
1.Use shortest line cords possible.
2.Use 2 conductor line cords to connect all single line equipment.
3.Disconnect line 2 wires on any jack where not needed.
Crosstalk
If crosstalk occurs while phones are plugged into the network interface, inside wiring is
NOT the problem. Plug separate phones into the individual interfaces for each line.
Both lines will need to be in use at the same time to get valid test results.
TWO SINGLE LINE JACKS
Verify that 2 conductor line cord is connected to L1/L2 port on telephone. 4 conductor
cord may be used at L2 port.
SINGLE LINE TELEPHONE EQUIPMENT
If single line telephone equipment is also experiencing crosstalk, customer may try the
following remedies:
1.Use shortest line cords possible.
2.Use 2 conductor line cords to connect all single line equipment.
3.Disconnect line 2 wires on any jack where not needed.
TWO-LINE JACKS
·Use triplex adapter and 2 line cords at each affected two-line set.
·Connect cords to L1 and L2 on adapter (not L1+L2) cannot use wall phones with triplex
adapter.
Suggestions for reducing local telephone line recordings:
·If possible advise your callers to leave a message.
·Check with the local telephone company and advise them 7-10 seconds of silence is
required for the answering system to disconnect.
NOTE: Charges may apply
Call Waiting disconnects answering system
Answering System senses a fluctuation in line voltage caused by the Call Waiting signal
and disconnects.
Contact Local Telephone Company for possible solutions.
External Antennas
Additional external antennas are not recommended for the following reasons:
·AT&T cordless telephones are designed to ensure that the power output of the set does
not exceed standards set by the FCC. The maximum power output allowed is .1 watt (or
100 milliwatts).
·Any attachment to a cordless telephone which increases the power output is in violation
of FCC regulations.
·Once the product is opened in order to connect the external antenna, the warranty is
voided.
Hearing Aid Compatibility
This product is compatible with inductively coupled hearing aids.
Use of any other amplification devices near or on the cordless product may produce
squealing, whistling, or feedback.
·If you use a hearing aid in only one ear, cradle the handset to the other ear to try to avoid
microphone feedback.
·Remove or turn off the hearing aid when using the handset.
·Use a different extension telephone if you are unable to use the product without
assistance of a hearing aid.
Information regarding inductively coupled hearing aids:
·This type of hearing aid is usually equipped with a T (telephone ) switch, specifically
installed for improved amplification with telephone use.
·Flip the T switch to the telephone position to turn off the hearing aid microphone and
turn on the inductive pickup coil that receives voice signals through a magnetic field
generated by some telephone handset.
·Not all telephones generate a sufficiently strong magnetic field to couple to these hearing
aids.
·Those that do are labelled Hearing Aid Compatible by AT&T.
Hearing Aid Compatibility
This product is compatible with inductively coupled hearing aids.
Clean Charging Contacts
·Each month clean handset and base charging contacts using a pencil eraser or a cloth to
eliminate deposit accumulation.
·Charge light should come on when handset is cradled in base.
·Charge handset for 10 hours.
Calling in same Area Code
Many LTCO's are changing their dialing sequence to 0 +, or 1 +, 10-digit dialing (0 + 0r
1 + area code + seven-digit phone number) for all long distance calls that are made within
the same area code. All 0 +, or 1 +, 7-digit dialing within the same area code will be
eliminated. This also means that local credit card and operator assistance calls that
traditionally have been 0 + 7 dialed calls will now require 0 + 10 dialing. You will
continue 0 + or 1 + 10 digit dialing for long distance calls into other area codes as you do
today.
Recradle unplug AC
1.Unplug the AC adapter from the wall outlet.
2.Remove battery cover on handset.
3.Unplug batteries from back of handset.
4.Wait 15 seconds and reinstall batteries securely.
5.Replace battery cover.
6.Recradle handset in base, replug AC adapter and wait 15 seconds.
7.Pick up handset and press phone.
NOTE: Be sure batteries have been charged recently.
Recradle unplug AC
1.Unplug the AC adapter from the wall outlet.
2.Remove battery cover on handset.
3.Unplug batteries from back of handset.
4.Wait 15 seconds and reinstall batteries securely.
5.Replace battery cover.
6.Recradle handset in base, replug AC adapter and wait 15 seconds.
7.Pick up handset and press phone.
NOTE: Be sure batteries have been charged recently. If not, charge batteries fully for 16
Hours.
Handset Locked Up (Battery ) :
1.Remove battery cover on handset.
2.Unplug battery from back of handset.
3.Wait 15 seconds.
4.Reinstall battery securely.
5.Replace battery cover.
6.Recradle handset in base for 15 seconds.
7.Pick up handset and press phone.
NOTE: Be sure batteries have been charged recently.
Handset Locked Up (Battery ) :
1.Remove battery cover on handset.
2.Unplug battery from back of handset.
3.Wait 15 seconds.
4.Reinstall battery securely.
5.Replace battery cover.
6.Recradle handset in base for 15 seconds.
7.Pick up handset and press phone.
NOTE: Be sure batteries have been charged recently. If not, charge batteries fully for 16
hours.
Common Cure
If the unit does not seem to be responding normally, then try putting the handset in the
base to reinitialize the unit. If it still does not seem to respond after doing this a few
times, do the following (in the order listed):
1.Unplug the power cord.
2.Remove the handset battery.
3.Wait a few minutes.
4.Plug the power cord into an electrical outlet.
5.Install the handset battery.
6.Put the handset in the base to reinitialize.
Base Unit Locked Up:
1.Recradle handset in base.
2.Unplug AC adapter from wall outlet.
3.Wait 15 seconds.
4.Reconnect AC adapter.
5.Wait 15 seconds.
6.Pick up handset and press PHONE button.
Single Audio Path Mutes
Ringing from another line may briefly mute a conversation since this product is designed
with a single audio path. This is a normal occurence.
Chirping Sounds
If chirping sounds are detected from the handset or base, check the following possible
causes:
·Smoke detectors
·Other cordless telephones
·Alarm clocks
To enable the unit to work with business systems:
·Install the unit at the control box, or
·Wire a jack around the system.
NOTE: Unit will not have business system features if installed in this manner.
Check with the local telephone company to inquire as to possible low line voltage.
NOTE: The recommended voltage is 24 to 48 on hook.
Due to reduced line voltage, avoid having additional extension telephones "off the hook"
during a call.
Wet Handset
A handset dropped in water may still operate if left out to dry.
1.Empty any residual water.
2.Leave handset face down on a towel to dry for 72 hours.
3.If handset does not operate after 72 hours, send it in for repair.
To determine if telephones ring separately or together:
1.Remove telephones from line.
2.Replace one at a time.
·Line 1 has a higher pitched ring that helps differentiate it from the ring of Line 2.
·Have someone call on each line.
·Let the telephone ring approximately five times and listen to the difference.
·Try using 2 two conductor cords or purchase a 267C adapter.
·Try a Triplex adapter and use a two cord connection.
Ringer Volume Not Adjustable
Ringer volume cannot be adjusted.
If the volume is too loud, the ringer switch may be shut off.
NOTE: This will turn the ringer off completely and you will lose line lights.
4 Conductor Line Corfd
To determine if the unit's cord is four pin or two pin:
·Take another telephone "off the hook."
·Remove and inspect the telephone line cord.
Low Battery indicator
The Low Battery indicator does not appear if:
·The unit is completely charged.
·The handset has completely discharged.
If the handset is normally kept in the base, the light should not appear.
Unplug excessive telephones or adjuncts or disconnect the telephones needed to bring
ringer equivalence below total ringer equivalence.
Check with the local telephone company to inquire as to possible low line voltage.
NOTE: The recommended voltage is 24 to 48 on hook.
·Unplug both ends of the line cord.
·Plug in both ends of the line cord.
·Replace the line cord if the connections are loose.
Explain Call Waiting
Explanation to Call Waiting customers:
·The unit picks up the first call after the preset number of rings.
·The second caller hears the telephone ring until the unit resets and is ready to answer the
next call.
·There is no reset time.
More Than One Cordless
If more than 1 cordless installed, have customer check to see if handsets are cradled on
the correct base unit.
.
.
Ringer Equivalence
On the bottom of each telephone or adjunct is a Ringer Equivalence.
1.Find this number for everything connected to your telephone line.
2.Add up all the numbers to get the total Ringer Equivalence.
Julian Date
NOTE: Contact the telephone company, if required.
The Julian date for this unit is found on the bottom of the unit.
TAS units are manufactured in:
·Mexico (M)
·Taiwan (H)
·China (G)
·Thailand (L)
The Julian date (XX XXX X) is read as follows:
·The first two numbers (XX XXX X) represent the year (00 - 99) of manufacture.
·The next three numbers (XX XXX X) represent the day of the year (1 - 365) of
manufacture.
·The last letter (XX XXX X) represent the place (M, H, G, L) of manufacture.
So, for example, 92291G was built in 1992, on the 291st day, in China.
When asked if a Julian date is after 92291G, 922209H, or 92168M, compare the Julian
date the customer gives you with the Julian date above for the same manufacturing site.
For example, if the customer said,"93005G," you would compare it to 92291G and
answer, "Yes."
Digital Voice
The difference between the electronic and human voice:
The electronic voice is a digital reproduction of a human voice which is analog.