Installation
instructions
Integrated dishwasher
To prevent accidents
and machine damage,
read these instructions
before
installation or use,
M-Nr, 05 620 662
Contents
iMPORTANT SAFETY INSTRUCTmONS .................................
3
mNSTRUCTmONSmMPORTANTES SUR LA SECURmTE .....................
5
Caring for the environment ..........................................
Disposal of the packing material .......................................
Disposal of an old machine ...........................................
7
7
7
Opening the door ..................................................
Opening the door without a panel in place ...............................
Without the mounting bracket in place: ...............................
Product and Cut-out Dimensions .....................................
8
8
8
9
Installation ......................................................
1, install the steam deflector .........................................
11
11
2, install the mounting brackets .......................................
3, Install the slide skis ..............................................
14
14
4, install the dishwasher under the countertop ...........................
5. Level the legs ...................................................
6, install the custom door panel ......................................
15
16
17
7. Adjust and secure the front panel ...................................
8, Secure the dishwasher ...........................................
22
23
9, Adjust the door springs ...........................................
25
10, Make the plumbing connections ...................................
11, Make the electrical connection ....................................
26
30
12, Test the unit ...................................................
13, Install the toekick ...............................................
32
33
iMPORTANT
SAFETY
mnstallation
Insta!lation, maintenance
If there is any doubt concerning
installation contact the Technical
and
repair
work
shou,d
bebyaM,e,eService
authorized service technician. Work by
unqualified persons could be a hazard
and may void the warranty.
Department.
USA 1-800-999- !360
techserv@mieleusa.com
CDN 1-800-565-6435
service@miele.ca
Th,s
equipment
isnot
maritime
use or for
usedesigned
in mobile for
installations such as caravans or
aircrafL However, under certain
conditions it may be possible for an
installation in these applications. Please
contact the nearest Miele dealer or the
Miele Technical Service Department
with specific requirements.
i}
iNSTRUCTiONS
Inspect the dishwasher for
transport
damage.
Donot,nsta,,
or
use a damaged uniL Contact the place
of purchase.
This dishwasher must be installed
deracont_nuouscountertop
secured to adiacent cabinetry.
Do
not
,nsta,,
this
dishwasher
beneath a cooking surface or oven.
Donot,
under
any
e,rcumstances,
cut the intake hose or submerge in
liquid. This hose contains electrical
components that could cause iniury or
property damage if cut or submerged.
iMPORTANT
SAFETY
iNSTRUCTiONS
E_ectrica_ safety
ChHd safety
Before installation, make sure the
voltage and frequency listed on the
data plate correspond with the
household electrical supply. This data
must correspond to prevent injury and
machine damage. Consult a qualified
electrician if in doubL
To guarantee the electrical safety
of this appliance, continuity must
exist between the appliance and an
effective grounding system.
It is imperative that this basic safety
requirement be met. If there is any
doubt, have the electrical system of the
house checked by a qualified
electrician. The manufacturer cannot be
held responsible for damages caused
by the lack, or inadequacy of, an
effective grounding system
i
Before installation or service,
disconnect
thepower
supply
tothe
work area by manually "tripping" the
circuit breaker, unplugging the unit, or
removing the fuse.
Do not use an extension cord to
connect the unit to electricity.
Extension cords do not guarantee the
required safety of the appliance, (e.g.
danger of overheating).
Ensure
that
any
plastic
wrapping
bags etc.
are
disposed
of safely
and kept out of the reach of babies and
young children. Danger of suffocation!
,fthe
app,iance
isremoved
from
its
installation
and will
not be used,
the door to the wash cabinet should be
removed to prevent children from being
locked in the machine.
'
When discarding an old
dishwasher, unplug it from the
power outlet, remove the door to the
wash cabinet and cut off the power
cord.
iNSTRUCTiONS
JMPORTANTES
Installation
SUR LA SECURJTE
Si vous avez des doutes au sujet
de I'installation, contactez le D6partement du service technique Miele,
L'insta,ation
etlestravaux
de
r6paration
etd'entretien
doivent
Ure
effectu6s par un technicien de service
autoris6 Miele, Les travaux effectues
par des personnes non qualifi6es,
pourraient _tre dangereux et faire annuler la garantie,
Cet equipernent n'a pas 6t6 con_u
pour usage maritime ou pour les
installations mobiles te!les que les rouIottes ou les avions, Toutefois, il peut
6tre parfois possible de faire
I'installation de ces applications sous
certaines conditions, Veuillez contacter
le Concessionnaire Miele le plus pres
de chez-vous ou le D6partement du
service technique Miele pour leur donner vos exigences precises,
Inspecter le lave-vaisselle
pour voir
s'_aet6endommag6
_ors
de
I'exp6dition, Ne pas installer ou utiliser,
un appareil endommag6, Veuillez
contacter le point d'achat,
Ce lave-vaisse!le dolt 6tre installe
sous un comptoir continu bien fix6
aux armoires adjacentes,
Ne pas installer ce lave-vaisselle
sous une surface de cuisson ou un
four,
Ne jamais, sous aucunes circons-
tances,
couper
_eboyau
depr_se
ou submerger dans un liquide, Ce
boyau contient des el#merits #lectriques qui pourraient causer des blessures ou des d6g&ts mat@iels s'ils sont
coup6s ou submerg#s,
USA !-800-999-1360
techserv@mieleusa,com
CDN !-800-565-6435
service@miele,ca
_]HHHHHHHH
_;Jii]ii
i dOurant
leprocessus ii
installation, veuillez faire attention
ii aux rebords coupants qui peuvent
iNSTRUCTiONS
S6curite
JMPORTANTES
61ectrique
Avant I'installation, s'assurer que la
SUR LA SECUFHTE
Securite
des enfants
S'assurer de disposer de bus les
tension
et fr6quence
6num6r6es emba,ages
dep ast que,
sacs
etc
sur la plaque signal6tique correspondent b,la source d'61ectricit6 de la residence. Ces donnees doivent correspondre afin d'6viter de vous blesser et
d'endommager I'appareik Consulter un
electricien qualifi6 si vous avez des
doutes.
Pour garantir la s6curit6 electrique
de cet appareil, il dolt y avoir continuit6 entre I'appareil et un syst6me efficace de mise _. la terre. Ce critere de
s6curite dolt absolument 6tre respect6.
Si vous avez des doutes, loire v@ifier le
systeme 61ectrique de votre maison par
un 61ectricien qualifi6. Le fabricant ne
peut pas 6tre tenu responsable des
dommages caus6s par un systeme de
raise b,la terre efficace, manquant ou
inad6quaL
le courant
de lazone
...... D6branc
de travail her
avant
I'installation,
en d6branchant I'appareil, retirant le fusible
ou en faisant "sauter" le disjoncteuk
Ne pas utiliser de rallonge pour
brancher I'appareik Les ra!longes
ne garantissent pas la s6curit6 requise
pour I'appareil, (par ex. danger de surc hauffage).
et de les garder hors de la port6 des
b6bes et jeunes enfants. Danger de
suffocatio!!
Si I'appareil est retir6 de son installation et que vous ne !'utilisez pas,
vous devez retirer la porte du meuble
de lavage pour empScher les enfants
de s'enfermer dons I'appareik
Pour disposer d'un ancien
lave-vaisselle, le d6brancher
de la
prise, enlever la porte du meuble de lavage et couper le cordon @lectrique.
Caring
Disposa_
materia_
of the packing
The cardboard box and packaging
protect the appliance during shipping.
These materials are biodegradable and
recyclable. Please recycle.
Ensure that any plastic wrappings,
bags etc. are disposed of safely and
kept out of the reach of children.
Danger of suffocatio!!
Disposa_
for the environment
of an o_d machine
Old appliances may contain materials
that can be recycled. Please contact
your local recycling authority about the
possibilty of recycling these materials.
Ensure that the appliance presents no
danger to children while being stored
for disposal. Before discarding an old
appliance, unplug it from the outlet and
cut off its power cord and remove any
doors to prevent hazards.
Opening
the door
Opening the door without
pane[ in place
a
[] Gently pull on the upper portion of
the mounting bracket until the door
latch releases (small arrow),
Without
place:
the mounting
bracket in
[] Grip the T shaped opening with a
finger and pull the door open,
Product
G 600 Series
Dishwashers
Full size models G 643 - G 663
and Cut-out
Removing
Dimensions
the Jeg extensions
The black leg extensions can be
removed to reduce the machine height
to 32 1/4"- 33" (819-838 ram) (see
Inset).
A =
B =
Black leg extension (removable)
White leg (must be installed on
machine).
[] After removing the black leg
extensions, screw the white legs onto
the dishwasher.
i
Contact the Miele Technical Service
re necessary.
Department for the appropriate legs. .........
Product
and Cut-out
G 800 Series
Dimensions
Dishwashers
Full size models G 843 - G 863
greater than 35" (889 ram), extended ill
legs (part# 02 702 601) are
necessary.
Contact the Miele Technical Service
lO
Installation
1. mnstall the steam
deflector
A stainless steel steam deflector is
supplied to protect the countertop from
steam and condesation when the
dishwasher is opened, If the countertop
is made of Corian®, granite, marble or
other solid, waterproof material, the
steam deflector is not required,
The steam deflector has an indicator
reflector to show when the dishwasher
i_1IiIIiIIIIIIIIIIIIIIIIIIIIIIIIIIII_j_Hiji_f_IIIIII__[_i_i_i_i_i!!!
i
If the counter is made of different
materials, the steam deflector
should be positioned so it covers the
edge where the materials are ioined,
Countertops with wood or laminate
ii edging should be tacked through
i_i
_:
!
......
[] Remove the protective film from the
deflector,
is running,
[] Squeeze the supplied silicone
sealant along the groove of the
deflector,
11
installation
[] Center the steam deflector in the
opening for the dishwasher and align
with the lower front edge of the
cou ntertop,
Note:
For rounded countertops it may be
necessary to pull the steam deflector
closer to the counter's edge so the
optic reflector will be visible,
[] Secure the deflector in place using
the supplied nails,
[] Wipe of any excess silicone with a
solution of liquid dish soap and warm
water,
12
[] Press the optic indicator reflector in
place,
installation
Stone or marble countertops:
The steam deflector is not required for
countertops made of solid, waterproof
material. But it is needed for
determining the correct position of the
optic indicator reflector.
[] Remove the black plastic reflector
holder and the tape holding it in
place from the steam deflector.
[] Line up the D_acK reflector no_oer w_m
the tracing ana Dress nrc olace
[] With the reflector cut out left and
ffontward, align the steam deflector
with the front edge of the counter.
Trace the outline of the reflector onto
the underside of the counter with a
pencil.
Note:
For rounded countertops, make the
tracing closer to the counter's edge so
the optic reflection will be visible.
[] Adhere the double-sided
[] Press the optic indicator reflector into
the reflector holder.
sticker to
the back of the optic indicator
reflector,
/ Additional
i "Operati,ng
counter frominstructions
condensation.
See the
[] Remove the backing from the other
side of the sticker.
13
installation
2. Install
brackets
the mounting
To ensure stability this dishwasher
should be securely attached to the
countertop with the two mounting
brackets included,
3. mnstaJJthe shale skis
Two slide skis are included and should
be installed on the feet of the
dishwasher before the machine is
pushed under the countertop, This will
allow the machine to slide easier,
protect the floor, and allow adiustment
of the rear leveling legs from the front of
the unit,
[] First, adjust the height of the legs so
rna_ _ne _oD _f me alsnwasner is
ougnly l/s /3 mm _elow the
coun[er_c o
Tipping _ne macnlne s gnuy to the rear,
if possible _A make aajushng the front
legs easier Make sure the machine is
leve
wnen
aa:usfmenfs
are complete.
[] Insert the tab of each bracket into the
guide holes on top,
Stone or marble counterops:
Do not install these mounting brackets
if the counter is made of an extremely
hard material, The securing screws for
the mounting brackets are not suitable
for such materials,
[] Place the skis, with the ratchet at the
rear, under the dishwasher legs,
14
installation
4, Install
the dishwasher
under
the countertop
The dishwasher must be installed so
that the water and electricity supplies
can be accessed through an adiacent
cabinet. The supplies must not be
located behind the machine.
[] Make certain that there are no rough
edges that could damage the power
cord or hoses. If metal cabinets are
used, place the supplied rubber
grommet around the edge of the
opening before passing the cable
through.
z_WARNING - Fire hazard
Do not cover or crush the plug of an
electric appliance. Ensure that the
cabinet opening for the dishwasher
provides ample space for the plug.
Installing the dishwasher in a tight
space may crimp the power cord or
put pressure on the plug which may
cause overheating.
The floor of the cut out where the
dishwasher will be installed should be
even in height with the surrounding
kitchen floor. Plywood can be secured
to the floor to make the two areas even.
[] Slide the machine into the opening,
making sure the electrical cable and
hoses can reach their connection
points without kinking.
_i_iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiWiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii
_iiii_iii_iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii
_
The left side of the optic indicator
reflector and the optic indicator must
align.
The drain hose connection at the rear of
the dishwasher can be turned to allow
the hose to be angled to the right or
left.
[] Exercise care when sliding the
dishwasher in or out, to prevent
damaging the power cord or hoses.
[] Make a 2"x 4" (5 x 10 cm) cut out in
the side or bottom of the cabinet
adioining the dishwasher. This cut out
is necessary for connections to pass
through.
15
installation
5. Leve_ the _egs
[] The rear leveling legs can be
adiusted with a T20 Torx screwdriver
by turning the screws at the front of
the slide skis,
To raise the machine turn clockwise,
To lower the machine turn counter
clockwise,
Several turns may be needed to set the
correct heighL Do not use a power
screwdriver.
16
[] Adiust the front leveling legs by
pushing on the feet with a slotted
screwdriver,
[] Tipping the machine slightly
backwards, if posssible will make
adjusting the front legs easier, Make
sure the machine is level when
adjustments are complete,
_i The dishwasher should be raised
until it just touches the underside of
installation
6. mnstaH the custom
door
PaneJ Dimensions:
pane_
Width: ...............
A custom door panel must be installed
on the dishwasher before it can be
Range of panel heiqht:
safely operated. A single large panel or
a two piece panel separated at the
drawer line can be used.
G 800 series ..........
...................
27 1/2"- 30 1/4"
(699 - 768 ram)
G 600 series ..........
...................
25 1/2"- 28 1/4"
(648- 718 ram)
Panel size is determined
following manner:
in the
_ele
Integrated
D shwasher
23 1/,,
,2 (60 ore)
Thickness:
At least s/4" (!8 ram) where the
mounting bracket is to be screwed in
position.
Maximum panel weiqht:
G 800 series ..........
G 600 series ........
21 Ibs (9.5 kg)
16.5 Ibs (7.5 kg)
Panel Height = HTC - TKH
HTC = Height to the underside of
countertop
TKH = Toe Kick Height
17
installation
The door panel is attached to the
dishwasher using the mounting bracket
that comes secured to the front of the
unit,
To remove the bracket:
[] Open the door 2- 4" (5 - 10 cm),
[] Loosen the bracket retaining screw
(black arrow) located on each side of
the machine door,
[] Pull the bracket up until the upper
section of the bracket disengages
from the Iocator pins, then remove
the bracket,
18
Installation
Install the bracket on the rea_ of the
custom
doo_ panel
[] Make sure the dishwasher is leve!,
[] Measure the distance X between the
round hole in the machine outer door
panel (shown in inset) and the lower
edge of the adioining cabinet door.
f
[] Using a pencil, lightly draw a vertical
centerline on the panel (See
illustration on the next page),
[] Draw a horizontal line X inches up
from the bottom edge of the panel,
For two piece panels:
Two piece panels should be made so
that any ioining hardware is flush with
the back of the panel, Failure to do this
may impede proper operation of the
dishwasher,
In certain instances, you may be able
to use the mounting bracket supplied
with the machine to secure both pieces
to the dishwasher,
Consult your cabinet supplier / maker
for the best method of ioining the
panels,
[] Place the door panel on a flat
surface, good side face down, being
careful not to scratch the surface,
Make certain that the bottom of the
panel is towards you,
_i When mounting the two pieces,
make sure that the desired finished
.................
19
Installation
[] Place the bracket on the door panel
so the notches, _, cross the
previously drawn centerline, and the
bottom of the bracket lines up with
the horizontal X line.
[] Mark and drill pilot holes for the
3
Ii
screws using a /32 (2,5 ram) drill bit.
[] Attach the bracket to the back of the
panel, using the 14 screws provided.
The top four pair of holes, only need
to be secured once per pair.
2O
[] Double check the location of the
bracket before mounting the panel to
the dishwasher.
The door handle must be installed on
the panel before it is attached to the
machine. It should be located in the
center of the panel at a height that will
match the surrounding drawer handles.
Any screws used to attach the door
_i handle must be countersunk so that
i the rear of the front panel remains
installation
Attach the front panel to the
dishwasher
[] Open the door 2- 4" (5 - 10 cm),
The "T" shaped hanger behind the door
handle should fit easily into its
respective hole,
[] Place the lower mounting clips into
the slots of the dishwasher door as
shown in the illustration,
[] Seat the U shaped slots of the upper
bracket onto their respective Iocator
pins,
[] Press the panel against the door and
slide down so that all the brackets
catch,
21
installation
7. Adjust
panel
and secure
the front
Once installed, the panel can be raised
or lowered up to 1/lfi" (2 ram) to match
the cabinet lines.
Adiust one side of the door panel at a
time using a T20 Torx screwdriver.
[] If the upper screws on the edge of
the door are not loose, loosen them
slightly.
[] The panel can be raised or lowered
by turning the lower screw on each
side of the dishwasher door.
To raise the panel turn clockwise.
To lower the panel turn
counterclockwise.
22
Once this side of the panel lines up
with the cabinets, secure it by
tightening the _
screw on the
edge of the dishwasher door.
[]
Repeat the process with the other
side of the panel.
[]
Close the door.
[]
Check the alignmenL Readjust if
needed.
[]
Insert the supplied end caps into the
four screw holes.
installation
8. Secure
the dishwasher
[] Open the dishwasher door.
seal located at the top, outer edge
of the dishwasher is tight against the
bottom of the countertop.
Do not drill any additional holes
through the wash cabinet. If in doubt
on how to secure the dishwasher,
please call Miele's Technical Service
Department.
[] Using flat head screws, secure the
dishwasher to the countertop by
screwing through both the mounting
bracket and the steam deflector,
23
installation
For openings exactly 23 s/,,
,s (60 ore)
wide:
_x_f
''''¸''''''_''¸''_''''''''''''''¸'
...........................
_........................................................
!i!l
only be used for securing the
z_The side m°unting h°les sh°uld
dishwasher if the opening is exactly
23 5/8 (60 cm) wide.
Use of this method on larger
i openings can damage the machine
ii and cause leaks. Be careful not to
screw into an adjacent appliance.
[] Open the dishwasher door and
remove the caps covering the
mounting holes on the outer edge of
the wash cabinet.
[] Fasten the dishwasher to the
adiacent cabinets using the supplied
screws and bushings. A bushing
must be placed over the screw
before inserting it into its mounting
hole.
[] Tighten the screws and insert the
caps.
24
I
installation
9. Adjust
the door
springs
[] Open the dishwasher door halfway,
If the door remains in this position when
released, the springs are adiusted
correctly,
If the door drops, the tension on the
springs needs to be increased,
If it closes on its own, the tension on the
springs need to be decreased,
[] To adiust the door springs use a T20
Torx or a small slotted screwdriver
and turn the screw located behind
the door in the upper front strip, on
the left hand side of the dishwasher.
Do not use a power screwdriver.
- turn clockwise to increase
the tension
- turn counterclockwise to
decrease the tension,
Note:
If the door springs can not be adjusted
enough (the door falls), the custom
door panel is too heavy,
Call your Miele dealer or the Technical
Service Department for advice on
stronger door springs,
25
installation
10. Make the p_umbing
connections
An air gap is built into the water inlet
system to prevent potable water from
mixing with waste water.
The dishwasher can heat its own water
to the temperatures required by the
wash program. This allows the option of
connecting the machine to either a hot
or cold water source.
[] For lowest energy consumption
connect the dishwasher to a cold
water source.
[] For fastest possible wash times, with
slightly higher energy consumption,
connect the dishwasher to a hot
water source.
Hot water supply specifications:
Recommended temperature:
120 °F (49 °C)
max 140 °F (60 °C)
Water pressure:
Must be between 5 - 145 psi
(0.3 -10 bar).
If the water pressure is tee low, the
"Intake/Drain" or "Intake" indicator may
flash (see "Operating Instructions/
Frequently asked questions").
If the water pressure is toe high, a
pressure reducer must be installed.
26
New plumbing:
The water inlet hose comes equipped
with a 3/,,
_4 female hose thread connecter. This can be directly connected
to a shut off valve with s/4"MHT (male
hose thread ends).
Preferred
Installation:
The hose assembly should be installed
vertically so the hose exits from the
bottom of the valve box (not as shown).
If this is net possible, it can be installed
horizontally, provided the hose exit
remains beneath the main body of the
valve box (see illustration). The valve
box should also be installed so that it is
at least 10" (24 cm) above the floor (or
base of the cabinet), so that the excess
coiled hose will remain lower than the
valve box at all points.
installation
Existing
pJumbing:
' me standard "__ copper p_umo_ng for
s dishwasher a_reao', exIsfs wt_r a
,OfT Dresslon
fitting
aria
awe
as
pictured
I i_i_d_ji_i_[_[__
z_WARNING - Elcetrical Hazard
Do not cut the intake hose. If the
hose is cut, the dishwasher will not
work. There will be a water leak and
[] Cut the :_/s"copper tubing after the
valve.
[] Install the 3/ _sII compression to "_/j4`'
MHT (Male Hose Thread) adapter
(supplied with the machine), as
illustrated.
i
too long, coil it neatly and place it
ou could be injured. If the hose is
behind the machine.
[if
i
if
[}
i[
[i}
[] For any other size plumbing, buy the
correct size adapter from a hardware
store.
[] Connect the inlet hose to the existing
valve/adapter assembly.
27
installation
Drainage system
specifications:
O
The machine comes equipped with:
-
A5 fL long (1.5 m) flexible drain hose
with an internal diameter of 7/,8.
(22 mm). Drain hose extensions can
be ordered from Miele's Technical
Service Department.
-
A built-in swivel connector allowing
the drain hose to be routed in any
direction.
-
A built-in mechanical non-return
valve on the discharge side to
prevent waste water from flowing
back into the dishwasher.
-
A built-in odor trap on the discharge
side to prevent odors from entering
the kitchen.
Maximum drain height: 39" (! m)
Maximum drain hose length: 12 ft
(3.5m)
Do not shorten
the drain hose.
Do not connect
the drain hose to
anything but a genuine MieJe hose.
Other hoses may melt or collapse.
28
Connect the supplied drain hose to the
drain pipe of the kitchen sink either:
-
above the P trap using the clamp
provided, or
-
to the dishwasher connector of the
garbage disposal.
When connecting the drain hose to
the garbage disposal, make sure to
remove the knockout from the
connection nipple. (See the disposaJ
manufacturer's
instructions for this
procedure.)
installation
Venting
the drainage
system
If the dishwasher drain hose is
connected to a floor drain or to a
drain pipe that is less than 8" (20 cm)
above the floor, the drain must be
vented, Otherwise the water inside the
dishwasher may siphon out during the
wash program,
To vent the drain:
[] Open the dishwasher door and
remove the lower basket,
Additional
note
Since all Miele dishwashers are
equipped with an odor trap and nonreturn valve, the drain hose can be
connected directly to the drain pipe as
illustrated,
If plumbing codes require an external
air gap on the discharge side of the
dishwasher, the following requirements
must be met:
-
No part of the drain hose should be
higher than 39" (! m),
-
If installed horizontally, the drain
hose can be up to 12 ft (3,5 m) long,
If the drain hose is angled upwards
in any way, it cannot be longer than
5 ft (! ,5 m),
-
The drain connection should be
made as close as possible to the
dishwasher,
-
The internal diameter (7/8" or 22 ram)
of the drain hose should not be
reduced at any point,
[] Cut off the vent cap located at the
right rear of the triple filter system, as
illustrated,
29
installation
11. Make the e_ectrica_
connection
GROUNDmNG mNSTRUCTmONS
Specifications
The dishwasher comes equipped with a
4 ft (1.2 m) power cord with a molded
plug for connection to 120 V, 60 Hz,
15 A grounded receptacle.
Rated load: ..........
In the event of a malfunction or break
down, grounding will reduce the risk of
electric shock by providing a path of
least resistance for the electric current.
This appliance is equipped with a cord
having an equipment grounding
conductor and a grounding plug. The
plug must be inserteded in an
appropriate outlet installed and
grounded in according to local codes
and ordinances.
z_WARNINGAn improper
connection of the equipment
grounding conductor can resuJt in
e_ectric shock.
Do not modify the p_ug provided
with the appliance; if it will not fit
the outlet, have a proper out_et
installed by a qualified electrician.
If there is any question about the
proper e_ectrica_ connection or
grounding of this appliance to the
power supply, p_ease consult a
licensed e_ectdcian or call Mie_e's
Technica_ Service Department:
USA 1-800-999-1360
CDN 1-800-565-6435
3O
12.5 A/1500W
Voltage: ..................
Frequency: ..................
Circuit breaker: ................
120 VAC
60 Hz
15 A
Installation
Power outlet
Permanent
The power outlet for the appliance must
be installed within a cabinet, on a wall
adjacent to the undercounter space in
which the dishwasher is located, An
opening through the partition between
the compartments of 1 1/2"(3 to 4 cm)
can be made to allow the plug to pass
through,
For hard wiring, the power cord must
be disconnected from the terminal box
located at the lower left front of the
dishwasher, behind the toekick and
service panel, Pass the permanent
power supply cable through the strain
relief and secure it to the terminal box,
Connection
(Hard Wiring)
Connect:
L1
(Black) to L on terminal block
N
(White) to N on terminal block
GRND To ground connector
GROUNDING
INSTRUCTIONS
with the circuit conductors and
connected to the equipment
not cut the plug off the power
supply cord and connect it directly
i
31
JnstaJJation
12. Test the unit
Once the dishwasher is level and
secured it should be tested.
[] Remove all packing and literature
from inside the unit.
The yellow Child Safety Lock key
hung on the upper basket must be
removed before operating the
dishwasher. If not removed, the key
could become lodged in the
circulation pump.
[] Make sure the triple filter system in
the base of the wash cabinet is
locked in place. Turn the handle
clockwise to lock.
[] Close the soap dispenser. Do not
add detergenL
[] Run the dishwasher through the
"Rinse & Hold" program. See the
operating instructions for information
on operation and program selection.
32
[] Check for any leaks, odd noises and
flashing / lit fault indicators on the
control panel. See the "Operating
Instructions / Frequently asked
questions" if there is a problem.
Installation
13. Install
the toekick
For installations using a continuous
toekick or a cabinet matching toekick
Before installing the toekick,
measurements must be taken to ensure
that the toekick will not interfere with the
complete opening of the dishwasher
If the door panel hits the toekick when
the dishwasher door is opened, the
toekick must be cut shorter or recessed
deeper,
Note:
If a decorative or flush mount toekick is
desired, and (R) is less than s/4"
(! 9 ram), other modifications, such as
beveling the top rear edge of the
toekick, may be necessary,
_jI_jIII_(_IIIIIIIIIIIIIIIdt_]IIIIIIIII8IIIIIIIIIIIIIIIIIIIIIIIIIIIIIII
_i It is extremely important that the
toekick is removable in case service
dOOr,
The door panel overhang (P), and
toekick depth of recess (R), determine
the maximum dishwasher toekick
height (H),
If (H) is equal to or less than the toekick
height of the adjoining cabinets, no
interference will exist, provided that (R)
is at least a/4" (19 ram),
33
G 800 Series dishwasher
[] Insert the mounting bracket with the
flange pointing toward the center of
the machine,
[] Insert the mounting bracket with the
flange pointing toward the outside of
the machine,
[] Push the mounting brackets in as far
as possible by releasing the tension
on the spring clip (see illustration),
[] Push the mounting brackets in as far
as possible by releasing the tension
on the spring clip (see illustration),
34
installation
The included toekick will fit without
modification if the machine is set to its
maximum height and the toekick is
recessed as far as possible (4"/10 cm).
If the machine height is less than
maximum, or if the toekick is not
recessed 4" (10 cm), the toekick must
be shortened.
[] Screw the toekick onto the installed
brackets, with the cutting lines
towards the top, and pull out evenly
and slowly until it aligns with the
toekick of the adioining cabinets.
The rear of the toekick has two cutting
lines.
be pushed in, and the toekick
i reattached.
eJeased, The brackets can then
35
installation
[] Carefully open the dishwasher door
until it hits the toekick.
[] Using the front lower edge of the
door panel as a guide, draw a line
across the toekick.
[] Unscrew and remove the toekick.
[] If one of the cutting lines is close to
the line iust drawn, score the front of
the toekick, and snap off the excess,
otherwise, trim the toekick along the
line using a saw.
[] Screw the toekick back onto the
brackets, with the cut edge at the
bottom.
it does, remove the toekick and trim
i front panel does not hit the toekick. If
36
37
38
39
When contacting
the Technical Service,
please quote the model and seria| number
of your appiianceo
MieJe, Jnc,
MieUe Limited
Nationam Headquarters
9 Independence Way
Princeton, NJ 08540
Phone: 800o843o7231
609=419=9898
Fax:
609=419=4298
www.mieUeusa.com
National Headquarters
55G East Beaver Creek Road
Richmond Hill, ON L4B 1E5
Phone: 800=643=5381
905=707=1t71
Fax:
905=707=0177
www.mieUe.ca
info@mieUe.ca (general enquiries)
professionaU@mieUe.ca (commercial
Technical Service & Support
Nationwide
Phone:800=999=1360
Fax:
888=586=8056
enquiries)
Mielecare Nationam Service
Phone: 800=565=6435
905=850=7456
Fax:
905=850=6651
service@mieUe.ca(-[ech. Service)
Alterations rights reserved / MVi60 3304
This bio--friendly paper was bleached without the use of chlorine,
M,oNr, 05 620 662 / 01