Dwyer Series ZV1 Instruction manual
Add to My manuals2 Pages
Dwyer Series ZV1 Two-Way Zone Valve is ideal for flow control in hot and cold water HVAC systems. It is typically used in conjunction with a thermostat to control room temperature. The valve is available in 1/2˝, 3/4˝, and 1˝ sizes with 24 or 120 VAC power supply. The ZV1 has a quick opening flow characteristic and a cycle time of 11 seconds opening and 5 seconds closing. It has a maximum pressure limit of 300 psi and a temperature limit of 201°F. The valve is constructed of brass, stainless steel, and NBR and has an aluminum housing.
advertisement
V-24:Model PHO-1 3/9/10 10:33 AM Page 1
®
Series ZV1 Two-Way Zone Valves
Specifications - Installation and Operating Instructions
Bulletin V-24
A
Size
1/2˝
3/4˝
1˝
B
A [in (mm)]
4.15 (105.5)
4.15 (105.5)
4.31 (109.5)
C [in (mm)]
2.48 (63)
2.48 (63)
2.48 (63)
C
B [in (mm)]
3.54 (90)
3.66 (93)
3.74 (95)
ZV1 Series Zone Valves are ideal for flow control in hot and cold water
HVAC systems. Zone valves are typically used in conjunction with a thermostat to control room temperature. Units are available in 1/2˝, 3/4˝, and
1˝ sizes with 24 or 120 VAC power supply. Easy to install these units are direct replacements for competitor units. Manual override lever is easily accessible externally. Consult factory for 220 VAC power supply, optional auxiliary switches, and BSP or sweat connections.
Model
Normally Open
ZV1022-NO
ZV1024-NO
ZV1032-NO
ZV1034-NO
ZV1042-NO
ZV1044-NO
Normally Closed
ZV1022
ZV1024
ZV1032
ZV1034
ZV1042
ZV1044
Cv
3.78
3.78
3.78
3.78
8.02
8.02
Size
1/2˝
1/2˝
3/4˝
3/4˝
1˝
1˝
Supply Voltage
120 VAC
24 VAC
120 VAC
24 VAC
120 VAC
24 VAC
SPECIFICATIONS
Service: Compatible fluids.
Body: 2-way.
Line Size: 1/2˝ to 1˝.
End Connections: Female NPT (optional BSP, sweat connections).
Pressure Limits: Maximum: 300 psi (20.7 bar); Close-off: 1/2˝ to 3/4˝: 22 psi (1.5 bar), 1˝: 14.5 psi (1 bar).
Temperature Limits: Ambient: 32 to 104°F (0 to 40°C); Process: 0 to
201°F (0 to 94°C).
Wetted Materials: Brass, stainless steel, NBR.
Flow Characteristic: Quick opening.
Power Requirements: 120 VAC or 24 VAC, ±10%, 50/60 Hz. (Optional
220 VAC).
Power Consumption: 6.5 W.
Input: On/off.
Electrical Connection: 22 AWG, 5˝ (127 mm) long.
Cycle Time: Opening time: 11 seconds; Closing time: 5 seconds.
Enclosure Rating: General purpose.
Housing Material: Aluminum.
W.E. ANDERSON DIV., DWYER INSTRUMENTS, INC.
P.O. BOX 358 • MICHIGAN CITY, INDIANA 46361 U.S.A.
Phone: 219/879-8000
Fax: 219/872-9057 www.dwyer-inst.com
e-mail: [email protected]
V-24:Model PHO-1 3/9/10 10:33 AM Page 2
Instructions for Operation
2-way and diverting 3-way valve are installed as Figure 1, 2 and 3 shows. For high building, pressure reducing valves should be installed on branch pipes at ground floor.
Note: When the valve is mounted on a horizontal pipe, the angle must be positioned at less than 85°(see Figure 4).
When the valve is mounted on a vertical pipe, it must be prevented from dripping.
Manual operating lever: Move the manual operating lever slowly and hold in the retaining notch, and then the valve is in normal-opened position. When the valve is first powered on, the lever goes back to the automatic position again.
MAINTENANCE
Upon final installation of the Series ZV1 Two-Way Zone Valves, no routine maintenance is required. A periodic check of the system calibration is recommended. The Series ZV1 is not field serviceable and should be returned if repair is needed (field repair should not be attempted and may void warranty). Be sure to include a brief description of the problem plus any relevant application notes. Contact customer service to receive a return good authorization number before shipping.
Fig. 4
When installing a diverting 3-way valve, end “B” is the supply to the coil, end “A” is the by-pass. There is no mark for an inlet. End “A” and “B” are marked on the bottom of the valve.
When the valve has an auxiliary micro switch, the wiring diagram is as following:
©Copyright 2010 Dwyer Instruments, Inc.
Printed in U.S.A. 3/10
W.E. ANDERSON DIV., DWYER INSTRUMENTS, INC.
P.O. BOX 358 • MICHIGAN CITY, INDIANA 46361 U.S.A.
Phone: 219/879-8000
Fax: 219/872-9057
FR # RB-443459-30 Rev.2
www.dwyer-inst.com
e-mail: [email protected]
advertisement
Related manuals
advertisement