READ AND SAVE THESE INSTRUCTIONS
“Botanica” Series
Model No.
CF2500OB01
CF2500S01
Net Weight:
CF2500HTW01
CF2500TG01
20.0
Lbs.
®
Botanica Series
Ceiling Fan Owner's Manual
Part No. F40BP72200003
Form No. BP7220-3
!
WARNING
WARNING: To avoid fire, shock, and serious personal injury, follow these instructions.
Safety Instructions
1. Read your owner’s manual carefully and keep it for future reference.
2. Before servicing or cleaning unit, switch power off at service panel and lock service panel
disconnecting means to prevent power from being switched on accidentally. When the service
disconnecting means cannot be locked, securely fasten a warning device, such as a tag, to the
service panel.
3. Be careful of the fan and blades when cleaning, painting, or working near the fan. Always turn off
the power to the ceiling fan before servicing.
4. Do not put anything into the fan blades while they are turning.
5. Do not operate reversing switch until fan blades have come to a complete stop.
Additional Safety Instructions for Installation
1. To avoid possible shock, be sure electricity is turned off at the fuse box before wiring, and do not
operate fan without blades.
2. All wiring must satisfy National and Local Electrical Codes. Use the National Electrical Code if
Local Codes do not exist. The ceiling fan must be grounded as a precaution against possible
electrical shock. Electrical installation should be made or approved by a licensed electrician.
3. The outlet box and joist must be securely mounted and capable of reliably supporting at least 50
pounds. Use only U.L. outlet boxes listed as acceptable for fan support, and use the mounting
screws provided with the outlet box. Most outlet boxes commonly used for support of light
fixtures are not acceptable for fan support and may need to be replaced. Consult a qualified
electrician if in doubt.
4. The downrod furnished with the fan provides the minimum recommended floor to fan blade
clearance for an 8 foot ceiling.
5. The fan must be mounted with the fan blades at least 7 feet from the floor to prevent accidental
contact with the fan blades.
6. Follow the recommended instructions for the proper method of wiring your ceiling fan. If you do
not know enough about electrical wiring, have your fan installed by a licensed electrician.
WARNING: To avoid fire, shock or injury, do not use an Emerson or any other brand of control not
specifically approved for this fan.
WARNING: This product is designed to use only those parts supplied with this product and/or any
accessories designated specifically for use with this product by Emerson. Substitution of parts or
accessories not designated for use with this product by Emerson could result in personal injury or
property damage.
WARNING: To Reduce the risk of personal injury, do not bend the blade flange when installing the
blade flanges, balancing the blades or cleaning the fan. Do not insert foreign objects in between
rotating fan blades.
2
This Manual Is Designed to Make it as Easy as Possible for You to
Assemble, Install, Operate and Maintain Your Ceiling Fan
Installed Wire Length
Up to 50 ft.
50-100 ft.
Tools Needed for Assembly
One Phillips head screwdriver
Three wire connectors (supplied.)
One stepladder
One wire stripper
MATERIALS
!
Wiring, outlet box and box connectors must be of type
required by the local code. The minimum wire would be a
3-conductor (2-wire with ground) of size shown at right:
Wire Size A.W.G.
14
12
WARNING
Before assembling your ceiling fan, refer to section on
proper method of wiring your fan. If you feel you do not
have enough wiring knowledge or experience, have
your fan installed by a licensed electrician.
Unpacking Instructions
For your convenience, check-off boxes are provided next to each step. As each step is
completed, place a check mark in the box. This will insure that all steps have been
completed and will be helpful in finding your place should you be interrupted.
!
NOTE: Place the parts from the loose parts bags
in small containers to keep them from being lost.
If any parts are missing, contact your local
retailer or catalog outlet for replacement before
proceeding.
WARNING
Do not install or use fan if any part is damaged or
missing. Call Toll-Free:
1-800-654-3545
!
NOTE: Fan blades are ordered separately and are
packaged in separate carton.
WARNING
This product is designed to use only those parts
supplied with this product and/or any accessories
designated specifically for use with this product by
Emerson. Substitution of parts or accessories not
designated for use with this product by Emerson
could result in personal injury or property damage.
MOTOR
COVER
UPLIGHT LEAD
ASSEMBLY
LOOSE
PARTS BAG
1. Open styrofoam unit containing fan. Remove top
half of styrofoam unit. Remove parts and check to
see that you have received the following:
a.
b.
c.
d.
e.
f.
g.
h.
i.
HANGER BALL/
DOWNROD
ASSEMBLY
SWITCH HOUSING
COVER ASSEMBLY
CEILING
COVER
HANGER
BRACKET
Fan motor and housing assembly
One motor cover
One ceiling cover
Five blade flanges
One hanger ball/downrod assembly
One hanger bracket
One switch housing cover assembly
One uplight lead assembly
One loose parts bag containing:
1. One setscrew
2. One 5/32" hex wrench
3. One 3/16” hex wrench
4. Eleven 10-32 x 5/8" oval head screws
5. Two 1” threaded studs
6. Two 1-1/4” threaded studs
7. Four knurled knobs
8. Three wire connectors
9. Four 8-32 x 3/8" flat head screws
10. One pull chain pendant and coupling
11. One hairpin clip
12. One clevis pin
13. Four lockwashers
14. Sixteen 10-24 x 3/8" pan head screws
15. Sixteen flat washers
BLADE
FLANGES
FAN MOTOR AND
HOUSING ASSEMBLY
FOAM PACKING
CARTON
3
Electrical Requirements
SECTION A
Your new ceiling fan will require a grounded electrical
supply line of 120 volts AC, 60 Hz, 15 amp circuit.
The outlet box must be securely anchored and capable of withstanding a load of at least 50 pounds.
Assembly Instructions
for Installing the CF2500 Ceiling
Fan with a SW375 Receiver and a
SR330 Remote Control or with a
SW350 Wall Control
If you feel that you do not have enough electrical
wiring knowledge or experience, have your fan
installed by a licensed electrician.
!
IF THE CF2500 CEILING FAN IS BEING
INSTALLED WITH ANY OTHER CONTROL
METHOD, SKIP SECTION A AND GO TO
SECTION B TO BEGIN ASSEMBLY
INSTRUCTIONS.
WARNING
To reduce the risk of fire, electric shock, or personal
injury, mount fan to outlet box marked acceptable for
fan support, and use screws supplied with outlet
box. Mos outlet boxes commonly used for support of
light fixtures are not acceptable for fan support and
may need to be replaced. Consult a qualified electrician if in doubt.
1. Cut the white, blue, and black wires about 3"
above the motor coupling (Figure 1). Strip insulation 1/2" from end of wires and install a wire
connector on the black wire; this wire will not be
used. Remove the wire connectors from the red
and brown wires.
If your fan is to replace an existing ceiling light fixture,
turn electricity off at the main fuse box at this time and
remove the existing light fixture.
!
INSULATE BLACK
WIRE USING WIRE
CONNECTOR
WARNING
!
BLACK WIRE
BLUE WIRE
REMOVE WIRE
CONNECTORS
FROM RED AND
BROWN WIRES
MOTOR COUPLING SLOT
WHITE WIRE
Turning off wall switch is not sufficient. To avoid
possible electrical shock, be sure electricity is
turned off at the main fuse box before wiring. All
wiring must be in accordance with National and
Local codes and the ceiling fan must be properly
grounded as a precaution against possible electrical
shock.
3"
YELLOW
WIRE
MOTOR
COUPLING
WARNING
Figure 1
2. Loosen the setscrew in the hanger ball, slide the ball
down the downrod, and remove the clevis pin. Then
slide the hanger ball off the downrod (Figure 2).
Retain all parts for reinstallation in step 11.
To avoid fire, or shock, follow all wiring instructions
carefully.
Any electrical work not described in these
instructions should be done or approved by a
licensed electrician.
The Emerson CF2500 Ceiling Fan is designed to be
operated from a SR330 Remote Control, from a
SW350 Wall Control with a SW375 Receiver, or from
other fan/light controls. There are no controls supplied
with the ceiling fan. If you are going to control your
ceiling fan with a SR330 Remote Control or with a
SW350 Wall Control, proceed to “SECTION A”. If you
are to control your ceiling fan in any other manner,
proceed to “SECTION B”.
CLEVIS PIN
HANGER BALL
DOWNROD
SETSCREW
Figure 2
3. Push the wiring harness connector and the connector on the blue wire (both supplied with the
SW375 Receiver and the SW350 Wall Control),
and the connector on the uplight yellow lead
assembly (supplied with the fan) through the
downrod until they all extend about 4” out of the
downrod (Figure 3).
Uplight
This fan is supplied with a built-in uplight in the motor
housing. This uplight does not have a built-in switch to
turn it ON or OFF. A separate switch control must be
used to operate the uplight. This can be done with a
separate ON/OFF wall switch or one of the many
Emerson Fan/Light Controls, such as the SW375
Receiver, SR330 Remote Control or SW95L Controls.
The yellow lead supplied with this fan is the power
lead for the uplight.
4. Cut all wires approximately 3" from the end of the
downrod’. Strip insulation 1/2" from end of wires.
4"
UPLIGHT YELLOW LEAD ASSEMBLY
BLUE WIRE
WIRING
HARNESS
4
Figure 3
DOWNROD
CUT HERE
3"
5. Using wiring connectors (supplied), connect the
white, red, blue, brown, and yellow wires from the
downrod to the white, red, blue, brown and yellow
wires of the ceiling fan (Figure 4). Wires must be
connected color-to-color.
LEADS TO BE
POSITIONED IN
SLOT IN MOTOR
COUPLING
SETSCREW
SW375 RECEIVER
WHITE WIRE
DOWNROD
HAIRPIN
CLIP
MOTOR
COUPLING
BLACK WIRE
YELLOW WIRE
TO YELLOW
WIRE
BLUE WIRE
TO
BLUE WIRE
CLEVIS PIN
LISTED GENERAL
USE ON/OFF
WALL SWITCH
(MUST BE
USED WITH SR330
REMOTE CONTROL)
WHITE WIRE
RECEIVER
CONNECTOR
WIRING HARNESS
CONNECTOR
BLACK
BLACK WIRE
WIRE
DOWNROD
WHITE
WIRE
DOWNROD
BROWN WIRE
TO BROWN WIRE
BLACK WIRE
(NOT USED)
FAN
HOUSING
YELLOW WIRE
TO YELLOW WIRE
CLEVIS
PIN
MOTOR
COUPLING
CLEVIS
PIN
SW350
WALL
CONTROL
BLACK
BLUE WIRE
TO BLUE WIRE
WHITE WIRE
TO WHITE WIRE
HAIRPIN
CLIP
WHITE
RED WIRE
TO RED WIRE
BLACK
TO
120V SUPPLY
TO
120V SUPPLY
Figure 5
LIGHT FIXTURE
NOTE: Make sure the unused black motor lead is
capped with a wire connector. Make sure all wire
connectors are completely inside motor coupling
cover and not pinched between the motor
coupling cover and motor.
FAN BLADES REMOVED
FOR CLARITY
Figure 4
6. Fold all wires from the downrod into the slot in the
motor coupling, slide the downrod down the wires
and seat the downrod in the motor coupling. All
wires and wire connectors should be placed
through the motor coupling slot beneath the downrod (See Figure 5).
9. Screw two 1” threaded studs (supplied) into the
motor (Figure 6). Leave approximately 7/8” of the
stud extending above the motor. Slide the motor
cover over the downrod and rotate the cover until
the threaded studs protrude; install two knurled
knobs (supplied) to secure the cover.
7. Align the clevis pin holes in the downrod with the
holes in the motor coupling. Install the clevis pin
and secure with the hairpin clip. The clevis pin
must go through the holes in the motor coupling
and the holes in the downrod (Figure 5). Push the
straight leg of the hairpin clip through the hole near
the end of the clevis pin until the curved portion of
the hairpin clip snaps around the clevis pin. The
hairpin clip must be properly installed to prevent
the clevis pin from working loose.
!
KNURLED KNOB
MOTOR
COUPLING
COVER
WIRE
CONNECTORS
1" THREADED
STUD
MOTOR
WARNING
It is critical that the clevis pin in the motor coupling
is properly installed and the setscrew securely
tightened. Failure to verify that the pin and setscrew
are properly installed could result in the fan falling.
7/8"
Figure 6
8. Install the setscrew (supplied in the loose parts
bag) in the motor coupling and tighten using the
5/32” setscrew wrench (supplied) (Figure 5).
10. Position the ceiling cover over the downrod. Be
sure the cover is oriented correctly, with the large
opening at the top (Figure 7).
5
!
14. Use the 10 round recessed holes in the motor hub
marked with "5" and install the five blade assemblies
in accordance with Step 15.
15. Loosely attach one blade assembly to the motor
hub using two 10-32 x 5/8" oval head screws
(supplied) (Figure 10). Make sure the screws are
NOT tightened at this time. Repeat this procedure
for the four remaining blade assemblies.
16. The blade flanges have an interlocking feature that
must be fully engaged before tightening the
screws. Make sure all the flanges are properly
engaged and then tighten the flange screws In a
clockwise sequence. If one of the flanges does not
seat properly on the motor hub, loosen the
adjacent flange screws, re-engage and reseat the
flanges, then tighten the screws again.
WARNING
It is critical that the pin in the hanger ball is properly
installed and the setscrew securely tightened.
Failure to verify that the pin and setscrew are
properly installed could result in the fan falling.
11. Reinstall the hanger ball on the downrod as
follows. Route the motor leads through the hanger
ball and slide the hanger ball over the downrod
(Figure 7). Install the pin through the holes at the
top of the downrod and slide the hanger ball up
the downrod, aligning the ball so the pin is
captured in the groove in the top of the hanger
ball. Pull the hanger ball up tight against the pin
and securely tighten the setscrew in the hanger
ball. A loose setscrew could create fan wobble.
PIN
BLADE FLANGE
FLAT WASHER
(DO NOT REMOVE)
HANGER BALL
10-32 X 5/8"
OVAL HEAD SCREW
(3 PER BLADE
ASSEMBLY)
DOWNROD
SETSCREW
CEILING COVER
MOTOR HUB
Figure 10
Figure 7
!
12. Use three 10-24 x 3/8" pan head screws and flat
washers (supplied) to secure flange to blade
(blades ordered separately) (Figure 8). Repeat for
the remaining four blades.
WARNING
To reduce the risk of personal injury, do not bend the
blade flanges when installing the flanges, balancing
the blades, or cleaning the fan.
10-24 x 3/8" PAN HEAD
SCREW (3)
FLAT WASHER (3)
17. Reinstall the switch housing assembly by passing the
wires from the motor shaft through the collar, screw
the assembly onto the motor shaft (Figure 11).
Tighten the setscrew using the 5/32” hex wrench
(supplied). Engage the connector from the switch
housing to the motor connector. The two connectors
are keyed and must be mated correctly before they
can be engaged.
BLADE
BLADE FLANGE
Figure 8
MOTOR
CONNECTOR
SWITCH HOUSING
CONNECTOR
13. Using the 5/32” hex wrench (supplied), loosen the
setscrew in the collar and unscrew (counterclockwise) the switch housing assembly from the motor
shaft (Figure 9). Do NOT remove the flat washer
from the motor shaft.
SWITCH HOUSING ASSEMBLY
COLLAR
SETSCREW
SETSCREW
SWITCH HOUSING
ASSEMBLY
Figure 11
COLLAR
Figure 9
6
!
NOTE: CEILING COVER,
SUPPLY WIRES AND
FAN WIRES OMITTED
FOR CLARITY.
WARNING
The fan must be hung with at least 7' of clearance
from floor to blades (Figure 12).
OUTLET
BOX
CEILING
HANGER
BRACKET
AT LEAST
7'
HANGER BALL/
DOWNROD ASSEMBLY
Figure 14
!
WARNING
FLOOR
Figure 12
!
To avoid possible fire or shock, do not pinch wires
between the hanger ball/downrod assembly and the
hanger bracket.
WARNING
20. Position the receiver (supplied with the SW330
Remote Control or SW350 Wall Control) by
passing the opening in the receiver over the
downrod (Figure 15).
The outlet box must be securely anchored and capable
of withstanding a load of at least 50 lbs.
18. Securely attach the hanger bracket to the outlet
box using the two screws supplied with the outlet
box (Figure 13).
!
WARNING
HANGER
BRACKET
To reduce the risk of fire, electric shock, or personal
injury, mount fan to outlet box marked acceptable for
fan support, and use screws supplied with outlet
box. Most outlet boxes commonly used for support
of light fixtures are not acceptable for fan support
and may need to be replaced. Consult a qualified
electrician if in doubt.
!
1/8" FOAM
ADHESIVE
PAD
SW375
RECEIVER
HANGER
BALL
FLAT SIDE
WARNING
Hanger bracket must seat firmly against outlet box. If
the outlet box is recessed, remove wall board until
bracket contacts box. If bracket and/or outlet box are
not securely attached, the fan could wobble or fall.
CEILING
COVER
Figure 15
!
OUTLET
BOX
TWO SCREWS
SUPPLIED WITH
OUTLET BOX
TAB
WARNING
To avoid possible electrical shock, be sure electricity
is turned off at the main fuse box before wiring.
NOTE: If you are not sure if the outlet box is grounded, contact a licensed electrician for advice, as it
must be grounded for safe operation.
HANGER
BRACKET
21. Connect the black wire from the wiring harness to
the black (hot) supply wire (Figure 4). Connect the
white wire from the wiring harness to the white
(neutral) supply wiring. Connect the green ground
wires from the hanger bracket and the hanger ball
to the supply ground wire. Use wire connectors
supplied with your ceiling fan.
Figure 13
19. Carefully lift the fan and seat the hanger
ball/downrod assembly on the hanger bracket
that was just attached to the outlet box (Figure
14). Be sure the groove in the ball is lined up with
tab on the hanger bracket (Figure 13).
!
OPEN
SIDE
!
WARNING
WARNING
Check to see that all connections are tight, including
ground, and that no bare wire is visible at the wire
connectors, except for the ground wire. Do not
operate fan until blades are in place. Noise and fan
damage could result.
Failure to seat tab in groove could cause damage to
electrical wires and possible shock or fire hazard.
7
7. Route the white, blue, and black motor leads through
the downrod. Fold the yellow, red, and brown wires
into the slot in the motor coupling, slide the downrod
down the wires and seat the downrod in the motor
coupling (Figure 18).
8. Align the clevis pin holes in the downrod with the
holes in the motor coupling. Install the clevis pin and
secure with the hairpin clip (Figure 18). The clevis pin
must go through the holes in the motor coupling and
the holes in the downrod . Push the straight leg of the
hairpin clip through the hole near the end of the
clevis pin until the curved portion of the hairpin clip
snaps around the clevis pin. The hairpin clip must be
properly installed to prevent the clevis pin from
working loose. Pull on the hanger ball to make sure
the clevis pin is properly installed.
22. Securely connect the wiring harness connector to
the receiver connector, and connect the blue and
yellow wires to the blue and yellow wires from the
receiver (Figure 4).
23. Turn the receiver so that the flat side aligns with
the open side of the hanger bracket (Figure 15).
Fold and position the wires into the space above
the hanger ball and into the outlet box.
24. Feed the wires and connectors around the outside of the receiver, through the open side of the
hanger bracket, and into the outlet box. Slide the
receiver up and over the hanger bracket.
Remove the backing on the foam adhesive pads
and press the receiver against the ceiling.
25. To complete the ceiling fan assembly, skip to the
“FINAL ASSEMBLY” section of this Owner’s
Manual.
!
WARNING
It is critical that the clevis pin in the motor coupling
is properly installed and the setscrew securely
tightened. Failure to verify that the pin and setscrew
are properly installed could result in the fan falling.
SECTION B
Assembly Instructions for
Installing the CF2500 Ceiling Fan
with Any Other Control Method
(excluding the SW375 Receiver,
SR330 Remote Control or the
SW350 Wall Control)
DOWNROD
SETSCREW
1. Position the fan motor and housing assembly in the
lower foam packing so that the top of the motor is
facing you.
2. Separate, untwist and unkink the four motor leads.
3. Obtain the hanger ball/downrod assembly and
remove the hanger ball by loosening the setscrew
in the hanger ball until the ball falls freely down the
downrod (Figure 16). Remove the pin from the
downrod , then remove the hanger ball. Retain the
pin and hanger ball for reinstallation in step 9.
HAIRPIN
CLIP
MOTOR
COUPLING
CLEVIS PIN
DOWNROD
HAIRPIN
CLIP
CLEVIS
PIN
CLEVIS PIN
CLEVIS
PIN
MOTOR
COUPLING
HANGER BALL
DOWNROD
SETSCREW
Figure 16
4. Push the uplight yellow lead assembly connector
through the downrod (Figure 17) until it extends
about 4”.
5. Cut the yellow lead approximately 3” from the end
of the pipe. Strip insulation 1/2” from end of the
wires.
6. Using the wire connector supplied, connect the
uplight yellow lead assembly to the yellow lead
from the fan motor and housing assembly
(Figure 18).
4"
UPLIGHT YELLOW
LEAD ASSEMBLY
DOWNROD
Figure 18
9. Install the setscrew (supplied in loose parts bag) in
the motor coupling and tighten using the 5/32"
setscrew wrench (supplied) (Figure 19).
CUT
HERE
3"
Figure 17
8
!
WARNING
It is critical that the pin in the hanger ball is properly
installed and the setscrew securely tightened.
Failure to verify that the pin and setscrew are
properly installed could result in the fan falling.
DOWNROD
SETSCREW
PIN
MOTOR
HANGER BALL
DOWNROD
SETSCREW
Figure 19
CEILING COVER
10. Screw two 1” threaded studs (provided) into the
motor (Figure 20). Leave approximately 7/8” of the
stud extending above the motor. Slide the motor
cover over the downrod and rotate the cover until
the threaded studs protrude; install two knurled
knobs (supplied) to secure the cover.
NOTE: Make sure the red and brown leads are
separately capped with wire connectors. Make
sure red, brown, and yellow wire connectors are
completely inside motor coupling cover and not
pinched between the motor coupling cover and
motor.
Figure 21
14. Use three 10-24 x 3/8" pan head screws and flat
washers (supplied) to secure flange to blade
(blades ordered separately) (Figure 22). Repeat
for the remaining four blades.
10-24 x 3/8" PAN HEAD
SCREW (3)
FLAT WASHER (3)
KNURLED KNOB
BLADE
WIRE
CONNECTORS
RED LEAD
BROWN LEAD
MOTOR
MOTOR
COUPLING
COVER
WIRE CONNECTOR
BLADE FLANGE
YELLOW LEAD
1" THREADED
STUD
7/8"
Figure 20
11. Position the ceiling cover over the downrod. Be
sure the cover is oriented correctly, with the large
opening at the top (Figure 21).
12. Reinstall the hanger ball on the downrod as
follows. Route the motor leads through the hanger
ball and slide the hanger ball over the downrod
(Figure 21). Install the pin through the holes at the
top of the downrod and slide the hanger ball up
the downrod, aligning the ball so the pin is
captured in the groove in the top of the hanger
ball. Pull the hanger ball up tight against the pin
and securely tighten the setscrew in the hanger
ball. A loose setscrew could create fan wobble.
13. The blue, black, yellow and white leads exiting the
downrod are 80-inches long. Before installing fan,
measure up approximately 6 to 9-inches above the
ball/downrod assembly. Cut off excess leads and
strip back insulation 1/2-inch from end of leads.
NOTE: If you are installing your fan with a SR330
Remote Control or SW350 Wall Control, Do Not
Cut Terminal Off of the Yellow Lead.
9
(See Section A.)
Figure 22
15. Using the 5/32” hex wrench (supplied), loosen the
setscrew in the collar and unscrew (counterclockwise) the switch housing assembly from the motor
shaft (Figure 23). Do NOT remove the flat washer
from the motor shaft.
BLADE FLANGE
FLAT WASHER
(DO NOT REMOVE)
10-32 X 5/8"
OVAL HEAD SCREW
(3 PER BLADE
ASSEMBLY)
MOTOR HUB
Figure 23
16. Use the 10 round recessed holes in the motor hub
marked with "5" and install the five blade assemblies
in accordance with Step 17.
17. Loosely attach one blade assembly to the motor
hub using two 10-32 x 5/8" oval head screws
(supplied) (Figure 23). Make sure the screws are
NOT tightened at this time. Repeat this procedure
for the four remaining blade assemblies.
18. The blade flanges have an interlocking feature that
must be fully engaged before tightening the
screws. Make sure all the flanges are properly
engaged and then tighten the flange screws In a
clockwise sequence. If one of the flanges does not
seat properly on the motor hub, loosen the
adjacent flange screws, re-engage and reseat the
flanges, then tighten the screws again.
CEILING
AT LEAST
7'
FLOOR
Figure 26
SWITCH HOUSING ASSEMBLY
SETSCREW
!
WARNING
The outlet box must be securely anchored and capable
of withstanding a load of at least 50 lbs.
COLLAR
20. Securely attach the hanger bracket to the outlet
box using the two screws supplied with the outlet
box (Figure 27).
Figure 24
!
!
WARNING
To reduce the risk of fire, electric shock, or personal
injury, mount fan to outlet box marked acceptable for
fan support, and use screws supplied with outlet
box. Most outlet boxes commonly used for support
of light fixtures are not acceptable for fan support
and may need to be replaced. Consult a qualified
electrician if in doubt.
WARNING
To reduce the risk of personal injury, do not bend the
blade flanges when installing the flanges, balancing
the blades, or cleaning the fan.
19. Reinstall the switch housing assembly by passing the
wires from the motor shaft through the collar, screw
the assembly onto the motor shaft (Figure 24).
Tighten the setscrew using the 5/32” hex wrench
(supplied). Engage the connector from the switch
housing to the motor connector. The two connectors
are keyed and must be mated correctly before they
can be engaged (Figure 25).
!
WARNING
Hanger bracket must seat firmly against outlet box. If
the outlet box is recessed, remove wall board until
bracket contacts box. If bracket and/or outlet box are
not securely attached, the fan could wobble or fall.
OUTLET
BOX
MOTOR
CONNECTOR
SWITCH HOUSING
CONNECTOR
TWO SCREWS
SUPPLIED WITH
OUTLET BOX
TAB
COLLAR
HANGER
BRACKET
Figure 27
SETSCREW
SWITCH HOUSING
ASSEMBLY
Figure 25
!
21. Carefully lift the fan and seat the hanger
ball/downrod assembly on the hanger bracket that
was just attached to the outlet box (Figure 28). Be
sure the groove in the ball is lined up with tab on
the hanger bracket (Figure 27).
WARNING
The fan must be hung with at least 7' of clearance
from floor to blades (Figure 26).
!
WARNING
Failure to seat tab in groove could cause damage to
electrical wires and possible shock or fire hazard.
10
EMERSON FAN CONTROL
NOTE: CEILING COVER,
SUPPLY WIRES AND
FAN WIRES OMITTED
FOR CLARITY.
OUTLET
BOX
LISTED OUTLET BOX
BLACK FAN WIRE
RED
BLACK
GREEN WIRE
(GROUND)
FROM
HANGER
BRACKET
WHT.
BLUE
GREEN WIRE (GROUND)
FROM HANGER BALL
LISTED WIRE CONNECTOR (4)
WARNING
To avoid possible fire or shock, do not pinch wires
between the hanger ball/downrod assembly and the
hanger bracket.
!
TO 120
VOLT
SUPPLY
GROUND
WIRE
HANGER BALL/
DOWNROD ASSEMBLY
!
BLACK
(HOT)
WHITE
HANGER
BRACKET
Figure 28
LIGHT
CONTROL
GROUND
GROUND
THREE - CONDUCTOR CABLE
WITH GROUND BETWEEN
CEILING AND WALL OUTLET
BOXES
Figure 29
23. To complete the ceiling fan assembly, proceed to
the “FINAL ASSEMBLY” section.
WARNING
To avoid possible electrical shock, be sure electricity
is turned off at the main fuse box before wiring.
NOTE: If you are not sure if the outlet box is grounded, contact a licensed electrician for advice, as it
must be grounded for safe operation.
!
WARNING
Check to see that all connections are tight, including
ground, and that no bare wire is visible at the wire
connectors, except for the ground wire. Do not
operate fan until blades are in place. Noise and fan
damage could result.
NOTE: If you are installing a SR330 Remote
Control or a SW350 Wall Control to operate the
fan and light, refer to the installation instructions
and wiring diagrams shown in Section A of this
Owner’s Manual.
22. For a wall control installation you will need a
three-wire (with ground) conductor cable between
the ceiling and wall outlet boxes. This will allow
you to control the fan separately from the lights.
Figure 29 is a basic wiring diagram that will control the uplight and downlight on a switch and the
fan on a separate control. Refer to the installation
instructions and wiring diagrams supplied with the
Emerson Fan Control Owner’s Manual.
a. Connect the green grounding lead from the
hanger ball and the green grounding lead from
the hanger bracket to the grounding conductor
of supply (this may be a bare wire or a wire
with green colored insulation). Securely connect wires with wire connector supplied.
b. Securely connect the white wire from the
downrod to the supply white (neutral) wire
using wire connector supplied. Securely connect the black wire from the downrod to the
supply black (hot) wire using wire connector
supplied.
c. Cut terminal off of the yellow lead wire and
strip insulation 1/2” from end of wire.
d. Securely connect the blue wire and yellow wire
from the downrod to the supply red (hot) wire
using wire connector (supplied). After connections have been made, turn leads upward and
carefully push leads into the outlet box, with
the white and green leads on one side of the
outlet box and the black, blue and yellow leads
on the other side of the outlet box.
FINAL ASSEMBLY
1. Screw the two 1-1/4” threaded studs (provided) into
the tapped holes in the hanger bracket.
2. Lift the ceiling cover up to the threaded studs and
turn until studs protrude through the holes in the
ceiling cover (Figure 30).
3. Secure the ceiling cover in place by sliding
lockwashers over the threaded studs and installing
the two knurled knobs (supplied). (Figure 30.)
Tighten the knurled knobs securely until the ceiling
cover fits snugly against the ceiling and the hole in
the ceiling cover is clear of the pipe.
CEILING COVER
LOCKWASHERS (2)
1-1/4"
THREADED
STUD
KNURLED KNOB
Figure 30
!
WARNING
To avoid possible fire or shock, make sure that the
electrical wires are completely inside the outlet box and
not pinched between the ceiling cover and the ceiling.
4. Screw in three 40-watt (maximum) candelabra
base lamps into the uplight sockets on top of the
fan housing assembly.
11
Attaching Light Kit
5. Slip the pull chain through the bushing in the switch
housing cover assembly (Figure 31). Position the
cover assembly on the switch housing assembly
with the reversing switch lever positioned in the slot
provided. Secure the cover assembly to the switch
housing assembly using four 8-32 x 3/8” flat head
screws (provided).
6. Slip the switch pull chain through the hole in the
pendant (supplied), then secure the pendant by
snapping the coupling (supplied) onto the end of
the chain.
TRIM MEDALLION
BUSHING
To install an Emerson accessory light kit, remove the
four screws securing the switch housing cover
assembly to the switch housing. Remove the trim
medallion from the bottom of the switch housing cover
(Figure 32). Attach the light kit to the switch housing
cover assembly with the lockwasher and nut supplied
with the light kit (Figure 33). Install the light kit in
accordance with the Emerson light kit Owner's
Manual.
PULL CHAIN
REMOVE
HEX
SCREW
REMOVE
FLAT HEAD
SCREW (4)
SWITCH HOUSING
COVER ASSEMBLY
8-32 X 3/8"
FLAT HEAD
SCREW (4)
REVERSING
SWITCH LEVER
SWITCH HOUSING
COVER ASSEMBLY
SWITCH HOUSING
ASSEMBLY
REMOVE
TRIM
MEDALLION
Figure 31
Figure 32
Using Your Ceiling Fan
!
1. Restore electrical power to the outlet box by turning
the electricity on at the main fuse box.
WARNING
To avoid possible electrical shock, be sure electricity is
turned off at the main fuse box before wiring.
2. When controlled by a wall switch check the
operation of the fan by gently pulling on the
4-position speed control pull chain switch. The
operating sequence is as follows:
SWITCH HOUSING
COVER ASSEMBLY
LOCKWASHER AND NUT
(SUPPLIED WITH LIGHT KIT)
REVERSING
SWITCH
SPEED CONTROL
SWITCH PULL
CHAIN
LIGHT KIT
Figure 33
THREE-SPEED
1st Pull — HIGH
2nd Pull — Medium
3rd Pull — Low
4th Pull — OFF
3.When operated by an Emerson Remote Control,
check operation of fan and light in accordance with
the Remote Control Owner’s Manual.
4. If airflow is desired in opposite direction, turn your
fan off and wait for the blades to stop turning. Then
slide the reversing switch to the opposite position
and turn fan on again. The fan blades will turn in
the opposite direction and reverse the airflow.
12
!
WARNING: FOR YOUR OWN SAFETY TURN OFF POWER AT FUSE BOX OR CIRCUIT BREAKER
BEFORE TROUBLE SHOOTING YOUR FAN.
Trouble Shooting
TROUBLE
1. Fan will not start.
PROBABLE CAUSE
SUGGESTED REMEDY
1. Fuse or circuit breaker blown.
1. Check main and branch circuit fuses or
circuit breakers.
!
2. Fan sounds noisy.
2. Loose power line connections to the fan,
or loose switch wire connections in the
switch housing.
2. Check line wire connections to fan and
switch wire connections in the switch
housing.
1. Blades not attached to fan.
1. Attach blades to fan before operating.
2. Loose screws in motor housing.
2. Check to make sure all screws in motor
housing are snug (not over-tight).
3. Screws securing fan blade flanges to
motor hub are loose.
3. Check to make sure the screws which
attach the fan flanges to the motor hub
are tight.
!
3. Fan wobbles
excessively.
WARNING: Make sure main power is
turned off.
WARNING: Make sure main power is
turned off.
4. Wire connectors inside switch housing
rattling.
4. Check to make sure wire connectors in
switch housing are not rattling against
each other or against the interior wall of
the switch housing.
5. Screws holding blades to flanges are loose.
5. Tighten screws securely.
1. Setscrew in motor coupling is loose.
1. Raise motor cover and tighten setscrew
securely.
2. Tighten the setscrew in the hanger ball/
downrod assembly.
3. Check to be sure screws which attach
the fan blade flanges to the motor hub
are tight.
2. Setscrew in hanger ball/downrod assembly
is loose.
3. Screws securing fan blade flanges to motor
hub are loose.
4. Fan blade flanges not seated properly.
4. Check to be sure the fan blade flanges
seat firmly and uniformly to the surface
of the motor hub. If flanges are seated
incorrectly, loosen the flange screws and
retighten according to step 15 or 17 in
Sections “A” or “B” “Assembly Instructions”.
5. Hanger bracket and/or ceiling outlet box
is not securely fastened.
5. Tighten the hanger bracket screws to the
outlet box, and/or secure outlet box.
6. Fan blades out of balance.
6. Interchanging an adjacent (side-by-side)
blade pair can redistribute the weight
and result in smoother operation. Or use
supplied balancing kit to balance blades.
Maintenance
IMPORTANT CARE INSTRUCTIONS
for your Ceiling Fan
!
WARNING
Do not use water when cleaning your ceiling fan. It
could damage the motor or the blades and create the
possibility of an electrical shock.
Periodic cleaning of your new ceiling fan is the only
maintenance that is needed.
When cleaning, use only a soft brush or lint free cloth
to avoid scratching the finish.
Abrasive cleaning agents are not required and should
be avoided to prevent damage to finish.
13
Repair Parts
!
2
WARNING
The use of any other control not specifically
approved for this fan could result in fire, shock and
personal injury.
1
3
18
15
!
4
16
This product is designed to use only those parts
supplied with this product and/or any accessories
designated specifically for use with this product by
Emerson. Substitution of parts or accessories not
designated for use with this product by Emerson
could result in personal injury or property damage.
17
20
19
9
19
20
26
WARNING
29
ACCESSORIES
1. Ceiling Fan Light Kits (see store or catalog).
2. Ceiling Fan/Light Controls (see store or catalog).
3. Downrod Extension Kits (see store or catalog).
30
Before discarding packaging material,
be certain all parts have been removed.
12
28
HOW TO ORDER REPAIR PARTS
WHEN ORDERING REPAIR PARTS, ALWAYS GIVE
THE FOLLOWING INFORMATION:
• NAME OF ITEM
• MODEL NUMBER
• THE PART NUMBER
• THE PART DESCRIPTION
11
25
23
24
For repair parts, phone 1-800-654-3545.
10
5
6
7
21
8
27
22
14
13
14
Repair Parts List
Ref.
No.
Description
CF2500OB01
Botanica Models
CF2500S01
CF2500HTW01
CF2500TG01
761655-9
761655-16
761655-12
761655-13
1
2
3
Hanger Pack,
containing:
Bracket, Hanger (1)
Hanger Ball Assembly (1)
Downrod (1)
—
—
—
—
—
—
—
—
—
—
—
—
4
Cover, Ceiling
761620-9
761620-24
761620-12
761620-23
5
Hub, Rubber
760601
760601
760601
760601
6
Blade Assembly
(Full set for one fan)
*
*
*
*
7
Flange Set
(Full set for one fan)
761885
761885-1
761885-2
761885-3
8
Switch Housing Assembly
761902
761902
761902-1
761902
9
Cover, Motor
761621-9
761621-16
761621-12
761621-13
10
Motor
762304
762304
762304
762304
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
Parts Bag, containing:
Pin, Clevis (1)
Clip, Hairpin (1)
Coupling (1)
Pendant (1)
Wire Connector (3)
Wrench, Hex, 3/16”
Wrench, Hex, 5/32”
Stud, Threaded 1-1/4” (2)
Lockwasher (4)
Knob, Knurled (4)
Screw, 10-32 x 5/8" (11)
Screw, Flathead, 8-32 x 3/8" (4)
Screw, 10-24 x 3/8" (16)
Washer, Flat (16)
Setscrew, 7/16-18 x 1/4" (1)
Stud, Threaded, 1” (2)
761907-1
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
761907-1
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
761907
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
761907-1
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
27
Cover, Switch Housing Assembly
761889
761889-1
761889-2
761889-3
28
Aux. Capacitor
761453
761453
761453
761453
29
Screw, #8 Washerhead, 8-32 x 3/8” (4)
—
—
—
—
30
Uplight Lead Assembly
—
Owner's Manual
761790
761790
761790
761790
BP7220-3
BP7220-3
BP7220-3
BP7220-3
*Contact your nearest authorized Emerson fan dealer for replacement B52 blade accessories.
15
LIMITED WARRANTY
What The Warranty Covers:
This warranty covers the motor and the other components and accessories of your Emerson ceiling fan against all defects in
workmanship and materials. You must be the original purchaser or user of the product to be covered.
What The Period Of Coverage Is:
As it applies to the motor, this warranty will last for the lifetime of your ceiling fan. All other components and accessories are
covered by this warranty for one year from the date you purchased your ceiling fan. ANY IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, MADE WITH RESPECT TO COMPONENTS AND
ACCESSORIES IS ALSO LIMITED TO ONE YEAR.
What Will Emerson Company Do To Correct Problems:
Emerson will replace a defective Emerson Air Comfort Ceiling Fan motor, blade, component or other accessory at no charge to
you. If repair of the motor or blades is not practical or possible within a reasonable time and no replacement can be provided,
Emerson will refund the actual purchase price of your fan. WE WILL SHIP THE REPAIRED PRODUCT OR REPLACEMENT TO
YOU AT NO CHARGE, BUT YOU ARE RESPONSIBLE FOR ALL COSTS OF REMOVAL, REINSTALLATION AND SHIPPING OF
THE PRODUCT TO EMERSON.
How Can You Get Service:
YOU MUST HAVE PROOF OF YOUR PURCHASE OF THE CEILING FAN TO OBTAIN LIMITED WARRANTY SERVICE. KEEP YOUR
RECEIPT OR OTHER PROOF OF PURCHASE. You can return the product to our factory or to your nearest
authorized service center.
• To return the product to the factory, obtain a return authorization and service identification tag by writing to
Air Comfort Products, Division of Emerson Company, 8100 W. Florissant Ave., St. Louis, MO 63136. Include all model
numbers shown on the product with your request.
• To return the product to an authorized service center, call 1-800-654-3545 for the address of the nearest authorized service
center.
You will be responsible for all insurance, freight or other transportation charges to our factory or authorized service
center. Your Emerson Air Comfort Ceiling Fan should be properly packed to avoid damage in transit since we will not be
responsible for any such damage.
What Is Not Covered:
The glass globes and light bulbs of your ceiling fan are not covered by this warranty. This warranty also does not cover any
defects, malfunctions or failures caused by:
• Repairs by persons not authorized by Emerson Company,
• Use of parts or accessories not authorized by Emerson Company,
• Mishandling, improper installation, modifications or damage to your ceiling fan while in your possession, or
• Unreasonable use, misuse, abuse, including failing to do reasonable and necessary maintenance, and normal wear and tear.
Additionally, this warranty and any implied warranty of merchantability or fitness for a particular purpose are voided when:
• The original purchaser or user ceases to own the product, or
• The fan is moved from its original point of installation.
This warranty is only valid within the 50 states of the United States and the District of Columbia. No other written or oral
warranties apply, and no employee, agent, dealer or other person is authorized to give any warranties on behalf of Emerson
Company.
REPAIR, REPLACEMENT OR A REFUND ARE THE EXCLUSIVE REMEDIES AVAILABLE UNDER THIS WARRANTY AND
EMERSON IS NOT RESPONSIBLE FOR DAMAGES OF ANY KIND, INCLUDING INCIDENTAL AND CONSEQUENTIAL
DAMAGES. Incidental damages include but are not limited to such damages as loss of time and loss of use. Consequential
damages include but are not limited to the cost of repairing or replacing other property which was
damaged if this product does not work properly.
How State Law Relates To The Warranty:
Some states do not allow the exclusion or limitation of incidental or consequential damages so the above exclusion or
limitation may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary
from state to state.
Air Comfort Products
DIVISION OF EMERSON COMPANY
8100 W. Florissant ¥ St. Louis, MO 63136
Part No. F40BP72200003
Printed in Taiwan 04/03
Form No BP7220-3