Extron IN2118 Specification

Specifications — IN2118

Video — faceplates A, D, and G only

Gain ............................................... Unity

Bandwidth .................................... 400 MHz (-3dB)

Video input and loop-through — faceplates A, D, and G only

Number/signal type ................... 1 VGA–UXGA, Mac ® , Sun ® , SGI ™ analog RGBHV, RGsB input

1 VGA–UXGA RGB local monitor loop-through

Connectors .................................... 2 female 15-pin HD (1 for input, 1 for loop-through)

Nominal level ............................... 0.7V p-p for RGB

Minimum/maximum levels ...... Analog: 0.6V to 0.7V p-p with no offset

Impedance .................................... 75 ohms

Horizontal frequency .................. 30 kHz to 130 kHz

Vertical frequency ....................... 30 Hz to 120 Hz

Return loss .................................... <-34.0dB @ 5 MHz

Video output — faceplates A, D, and G only

Number/signal type ................... 1 analog RGBHV, RGsB (if RGsB is input)

Connectors .................................... 5 BNC female

Nominal level ............................... 0.7V p-p for RGB

Minimum/maximum levels ...... Analog: 0.3V to 1.5V p-p

Impedance .................................... 75 ohms

Return loss .................................... <-49.4dB @ 5 MHz

DC offset ....................................... ±1.9mV maximum with input at 0 offset

Sync — faceplates A, D, and G only

Input type ..................................... RGBHV, RGsB

Output type .................................. RGBHV, RGsB (if RGsB is input)

Input level ..................................... 2.4V to 3.7V p-p

Output level.................................. 4.4V p-p, unterminated

Input impedance .......................... 75 ohms

Output impedance ...................... 75 ohms

Max. propagation delay .............. 440 ns

Max. rise/fall time ....................... 40 ns

Polarity .......................................... Negative

Audio — faceplates A, D, and G only

Gain ............................................... Unbalanced output: +6dB; balanced output: +12dB

Frequency response ..................... 20 Hz to 20 kHz, ±0.05dB

THD + Noise ................................ 0.49% @ 1 kHz at 1Vrms

S/N ............................................... >70dB at rated maximum output

Stereo channel separation .......... >-56dB @ 1 kHz to 20 kHz

CMRR ............................................ >-95.0dBr @ 20 Hz to 20 kHz, 1Vrms

Audio input — faceplates A, D, and G only

Number/signal type ................... 1 stereo, unbalanced

Connectors .................................... 1 female 3.5 mm mini stereo jack

Impedance .................................... >10 kohms unbalanced, DC coupled

Nominal level ............................... -10dBV (316mV)

Maximum level ............................ +11.5dBu, (unbalanced) at 0.17%THD+N

Audio output — faceplates A, D, and G only

Number/signal type ................... 2 stereo, balanced/unbalanced

Connectors .................................... (2) 3.5 mm captive screw connectors, 5 pole

Impedance .................................... 57 ohms balanced

1-2 IN2118 Elevation Table Mountable Installation Interface • Specifications

Gain error ...................................... ±0.06dB channel to channel

Maximum level (Hi-Z) ................ >+24dBu, balanced or unbalanced at 0.17%THD+N

Maximum level (600 ohm) ......... >+24.5dBm, balanced or unbalanced at 0.17%THD+N

0dBu = 0.775 volts (RMS).

Control/remote — lift motor

Contact closure ............................ (1) 3.5 mm captive screw connector, 4-pole

Contact closure pin configurations 1 = +5V, 2 = GND, 3 and 4 = status feedback

General

Power ............................................. 90VAC to 260VAC, 47 to 63 Hz, TBD watts, internal, autoswitchable

Temperature/humidity .............. Storage -40° to +158°F (-40° to +70°C) / 10% to 90%, non-condensing

Operating +32° to +122°F (0° to +50°C) / 10% to 90%, non-condensing

Rack mount ................................... No, but furniture mountable

Enclosure type .............................. Metal

Enclosure dimensions

Top plate ........................... 9.15" W x 8.15" D (23.2 cm W x 20.7 cm D)

Interface elevation ........... 3.4” (8.6 cm) above the table’s surface

Overall ............................... 14.0” H x 12.2” W x 11.2” D (35.6 cm H x 30.9 cm W x 28.3 cm D), including flange

(These are not the cutout dimensions.)

CAUTION

Use the appropriate metal Extron routing template or refer to the surface cutout dimensions in the manual before cutting a hole in the furniture or other surface. Pay special attention to the direction the unit will face. Extron is not responsible for miscut mounting holes.

Product weight ............................. 15 lbs (6.8 kg)

Shipping weight ........................... 20 lbs (10 kg)

DIM weight .................................. TBD

Vibration ....................................... ISTA/NSTA 1A in carton (International Safe Transit Association)

Listings .......................................... ETL (UL1950)

Compliances ................................. CE

Maximum motor load ................. 30 lbs (13.6 kg); exceeding 10 lbs (4.5 kg) will shorten the motor life

Warranty ....................................... 3 years parts and labor

Specifications are subject to change without notice.

7.40-050203-D3-112012

IN2118Elevation Table Mountable Installation Interface • Specifications 1-3