Asus PA328 Series User guide

PA328 Series
LCD Monitor
User Guide
First Edition
October 2014
Copyright © 2014 ASUSTeK COMPUTER INC. All Rights Reserved.
No part of this manual, including the products and software described in it, may be reproduced,
transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any
means, except documentation kept by the purchaser for backup purposes, without the express written
permission of ASUSTeK COMPUTER INC. (“ASUS”).
Product warranty or service will not be extended if: (1) the product is repaired, modified or altered, unless
such repair, modification of alteration is authorized in writing byASUS; or (2) the serial number of the
product is defaced or missing.
ASUS PROVIDES THIS MANUAL “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS
OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL ASUS, ITS
DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL,
INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS,
LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE),
EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM
ANY DEFECT OR ERROR IN THIS MANUAL OR PRODUCT.
SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR
INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE,
AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS. ASUS ASSUMES NO
RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN
THIS MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT.
Products and corporate names appearing in this manual may or may not be registered trademarks or
copyrights of their respective companies, and are used only for identification or explanation nd to the
owners’ benefit, without intent to infringe.
ii
Contents
Contents....................................................................................................... iii
Notices.......................................................................................................... iv
Safety information........................................................................................ v
Care & Cleaning........................................................................................... vi
Chapter 1: Product introduction
1.1
Welcome! ..................................................................................... 1-1
1.2
Package contents.......................................................................... 1-1
1.3
Monitor introduction..................................................................... 1-2
1.3.1
Front view........................................................................ 1-2
1.3.2
Back view......................................................................... 1-3
1.3.3
QuickFit Function............................................................. 1-4
Chapter 2: Setup
2.1
Detaching the arm/base (for VESA wall mount)......................... 2-1
2.2
Adjusting the monitor................................................................... 2-2
2.3
Connecting the cables.................................................................. 2-3
2.4
Turning on the monitor................................................................. 2-4
Chapter 3: General instructions
3.1
OSD (On-Screen Display) menu ................................................. 3-1
3.1.1
How to reconfigure........................................................... 3-1
3.1.2
OSD function introduction................................................ 3-1
3.2
Specifications summary............................................................... 3-8
3.3
Troubleshooting (FAQ)................................................................. 3-9
3.4
Supported operating modes...................................................... 3-10
iii
Notices
Federal Communications Commission Statement
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions:
•
This device may not cause harmful interference, and
•
This device must accept any interference received including interference that
may cause undesired operation.
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance
with manufacturer’s instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment to an outlet on a circuit different from that to which the
receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
The use of shielded cables for connection of the monitor to the graphics card is
required to assure compliance with FCC regulations. Changes or modifications
to this unit not expressly approved by the party responsible for compliance could
void the user’s authority to operate this equipment.
As an Energy Star® Partner, our company has determined that this
product meets the Energy Star® guidelines for energy efficiency.
Canadian Department of Communications Statement
This digital apparatus does not exceed the Class B limits for radio
noise emissions from digital apparatus set out in the Radio Interference
Regulations of the Canadian Department of Communications.
This class B digital apparatus complies with Canadian ICES-003.
This Class B digital apparatus meets all requirements of the Canadian
Interference - Causing Equipment Regulations.
Cet appareil numérique de la classe B respecte toutes les exigences du
Réglement sur le matériel brouiller du Canada.
iv
Safety information
•
Beforesettingupthemonitor,carefullyreadallthedocumentationthatcame
withthepackage.
•
Topreventfireorshockhazard,neverexposethemonitortorainormoisture.
•
Nevertrytoopenthemonitorcabinet.Thedangeroushighvoltagesinsidethe
monitormayresultinseriousphysicalinjury.
•
Ifthepowersupplyisbroken,donottrytofixitbyyourself.Contactaqualified
servicetechnicianoryourretailer.
•
Beforeusingtheproduct,makesureallcablesarecorrectlyconnectedandthe
powercablesarenotdamaged.Ifyoudetectanydamage,contactyourdealer
immediately.
•
Slots and openings on the back or top of the cabinet are provided for
ventilation. Do not block these slots. Never place this product near or over a
radiatororheatsourceunlessproperventilationisprovided.
•
Themonitorshouldbeoperatedonlyfromthetypeofpowersourceindicated
on the label. If you are not sure of the type of power supply to your home,
consultyourdealerorlocalpowercompany.
•
Usetheappropriatepowerplugwhichcomplieswithyourlocalpowerstandard.
•
Donotoverloadpowerstripsandextentioncords.Overloadingcanresultinfire
orelectricshock.
•
Avoid dust, humidity, and temperature extremes. Do not place the monitor in
anyareawhereitmaybecomewet.Placethemonitoronastablesurface. •
Unplugtheunitduringalightningstormorifitwillnotbeusedforalongperiod
oftime.Thiswillprotectthemonitorfromdamageduetopowersurges.
•
Never push objects or spill liquid of any kind into the slots on the monitor
cabinet.
•
To ensure satisfactory operation, use the monitor only with UL listed
computers which have appropriate configured receptacles marked between
100-240VAC.
•
If you encounter technical problems with the monitor, contact a qualified
servicetechnicianoryourretailer.
Thissymbolofthecrossedoutwheeledbinindicatesthattheproduct(electrical,
electronic equipment, and mercury-containing button cell battery) should not
be placed in municipal waste. Please check local regulations for disposal of
electronicproducts.
AEEE yönetmeliğine uygundur
v
Care & Cleaning
•
Before you lift or reposition your monitor, it is better to disconnect the cables
and power cord. Follow the correct lifting techniques when positioning the
monitor. When lifting or carrying the monitor, grasp the edges of the monitor.
Do not lift the display by the stand or the cord.
•
Cleaning. Turn your monitor off and unplug the power cord. Clean the monitor
surface with a lint-free, non-abrasive cloth. Stubborn stains may be removed
with a cloth dampened with mild cleaner.
•
Avoid using a cleaner containing alcohol or acetone. Use a cleaner intended
for use with the monitor. Never spray cleaner directly on the screen, as it may
drip inside the monitor and cause an electric shock.
The following symptoms are normal with the monitor:
•
You may find slightly uneven brightness on the screen depending on the
desktop pattern you use.
•
When the same image is displayed for hours, an afterimage of the previous
screen may remain after switching the image. The screen will recover slowly or
you can turn off the Power Switch for hours.
•
When the screen becomes black or flashes, or cannot work anymore, contact
your dealer or service center to fix it. Do not repair the screen by yourself!
Conventions used in this guide
WARNING: Information to prevent injury to yourself when trying to
complete a task.
CAUTION: Information to prevent damage to the components when trying
to complete a task.
IMPORTANT: Information that you MUST follow to complete a task.
NOTE: Tips and additional information to aid in completing a task.
vi
Where to find more information
Refer to the following sources for additional information and for product and
software updates.
1.
ASUS websites
The ASUS websites worldwide provide updated information on ASUS
hardware and software products. Refer to http://www.asus.com
2.
Optional documentation
Your product package may include optional documentation that may have
been added by your dealer. These documents are not part of the standard
package.
Takeback Services
ASUS recycling and takeback programs come from our commitment to the highest
standards for protecting our environment. We believe in providing solutions for
our customers to be able to responsibly recycle our products, batteries and other
components as well as the packaging materials.
Please go to http://csr.asus.com/english/Takeback.htm for detail recycling
information in different region.
vii
viii
1.1
Welcome!
Thank you for purchasing the ASUS® LCD monitor!
The latest widescreen LCD monitor from ASUS provides a broader, brighter and
crystal-clear display, plus a host of features that enhance your viewing experience.
With these features, you can enjoy the convenience and delightful visual
experience that the monitor brings to you!
1.2
Package contents
Check your package for the following items:
LCD monitor
Quick start guide
Warranty card
Power cord
HDMI cable
MHL cable (optional)
DisplayPort cable (optional)
DisplayPort cable (Mini-DP to DP)
USB 3.0 cable
Support CD
Cable tie
Color Calibration Testing Report
If any of the above items is damaged or missing, contact your retailer
immediately.
ASUS PA328 Series LCD Monitor
1-1
1.3
Monitorintroduction
1.3.1
Frontview
1
2
3
4
5
6
7
Standard Mode
DisplayPort 3840x2160@60Hz
Menu
Close
Input Select
Quick Fit
Brighness
Contrast
1.
Menu (5-way) button:
•
Press this button to enter the OSD menu.
•
Enacts the selected OSD menu items.
•
Increases/Decreases values or moves your selection up/down/left/right.
Close button:
2.
•
Exits the OSD menu.
•
Toggles the Key Lock function between on and off with a long press for
5 seconds.
Input select button:
3.
•
Selects an available input source.
Press
button (Input Select button) to display HDMI-1/MHL, HDMI2, HDMI-3, DisplayPort, mini DisplayPort signals after you connect HDMI/
DisplayPort/Mini DisplayPort cable with the monitor.
4.
QuickFit button:
•
This is a hotkey to activate the QuickFit function designed for alignment.
•
The QuickFit function contains 8 pages of common grid patterns, paper
sizes, and photo sizes. (Please refer to 1.3.3 QuickFit Function).
Shortcut
5.
1-2
•
Default: Brightness hotkey
•
To change the hotkey function, go to the Shortcut > Shortcut 1 menu.
Chapter 1: Product introduction
6.
Shortcut
•
Default: Contrast hotkey
•
To change the hotkey function, go to the Shortcut > Shortcut 2 menu.
7.
Power button/power indicator
•
Turns the monitor on/off.
•
The color definition of the power indicator is as the below table.
1.3.2
Status
Description
White
Amber
Off
On
Standby mode
Off
Back view
1
2
3
4
5
6
7
8
9 10
11
Rear connectors
1.
Kensington lock slot.
2.
Power switch. Press the switch to turn on/off power.
3.
AC-IN port. This port connects the power cord.
4.
HDMI (MHL) port. This port is for connection with an HDMI (MHL) compatible
device.
5.
6.
HDMI port. This port is for connection with an HDMI compatible device.
DisplayPort in. This port is for connection with a DisplayPort compatible
device.
7.
Mini DisplayPort in. This port is for connection with a Mini DisplayPort
compatible device.
ASUS PA328 Series LCD Monitor
1-3
8.
Earphone jack.
9.
USB 2.0 A-type. This port is for updating firmware only.
10. USB 3.0 upstream port. This port is for connection with a USB upstream cable.
The connection enables the USB ports on the monitor.
11. USB 3.0 downstream ports. These ports are for connection with USB devices,
such as USB keyboard/mouse, USB flash drive, etc.
1.3.3
•
HDMI-1/MHL port supports HDMI 2.0, 3840 x 2160-60Hz and MHL 3.0,
3840 x 2160-30Hz.
•
This monitor is Super-Speed USB 3.0 compatible.
QuickFit Function
The QuickFit function contains three kinds of patterns: (1) Grid patterns (2) Paper
size (3) Photo size. To activate the patterns, press the QuickFit button. Use the
Menu (5-way) button to select a desired pattern. You can move the button up/
down/left/right to change the pattern’s position if needed. Note that all the patterns
can be moved left/right accroding to your need, but may have limited range for
moving up/down.
1. Grid patterns
The grid patterns facilitate designers and users to organize content and layout on a
page and achieve a consistent look and feel.
Alignment Grid
Alignment Grid
1-4
Chapter 1: Product introduction
2. Paper size
QuickFit provides several commonly used standard paper sizes for users to view
their documents in real size on the screen.
A3
A4
A3
A4
B4
B5
B5
B4
Letter
Letter
3. Photo size
The various real photo sizes displayed in the QuickFit function provides
photographers and other users to accurately view and edit their photos in real size
on the screen.
Photo 4x6, 3x5, 2x2
4x6
Photo 8x10, 5x7
3x5
ASUS PA328 Series LCD Monitor
2x2
8x10
5x7
1-5
1-6
Chapter 1: Product introduction
2.1
Detaching the arm/base
(for VESA wall mount)
The detachable arm/base of this monitor is specially designed for VESA wall
mount.
To detach the arm/base:
1.
Have the front of the monitor face down on a table.
2.
Press the release button, and then detach the arm/base from the monitor (Figure
2).
(Figure 2)
(Figure 1)
2
1
We recommend that you cover the table surface with soft cloth to prevent
damage to the monitor.
•
The VESA wall mount kit (100 x 100 mm) is purchased separately.
•
Use only the UL Listed Wall Mount Bracket with minimum weight/load
22.7kg (Screw size: M4 x 10 mm)
ASUS PA328 Series LCD Monitor
2-1
2.2
Adjusting the monitor
•
or optimal viewing, we recommend that you look at the full face of the
F
monitor, then adjust the monitor to the angle that is most comfortable for you.
•
Hold the stand to prevent the monitor from falling when you change its angle.
•
ou can adjust the monitor’s angle from +20˚ to -5˚, and it allows 60˚ swivel
Y
adjustment from either left or right. You can also adjust the monitor’s height
within +/- 130 mm.
(Tilt)
(Swivel)
(Height adjustment)
+20° ~ -5°
130mm
60°
0°
60°
Pivoting the monitor
1. Lift the monitor to the highest position.
2. Tilt the monitor to its maximum angle.
3. Pivot the monitor clockwise to the angle you need.
+20° ~ -5°
It is normal that the monitor slightly shakes while you adjust the viewing angle.
2-2
Chapter 2: Setup
4. The OSD menu item will automatically rotate when the monitor rotates.
Standard Mode
DisplayPort 3840x2160@60Hz
Menu
Close
Input Select
Quick Fit
Brighness
Contrast
Standard Mode
DisplayPort 3840x2160@60Hz
Menu
Close
Input Select
Quick Fit
Brighness
Contrast
2.3
1.
Connecting the cables
Connect the cables as the following instructions:
Firmware upadate only
•
To connect the power cord: Connect one end of the power cord securely to
the monitor’s AC input port, the other end to a power outlet.
•
To connect the HDMI/DisplayPort/Mini DisplayPort cable:
a. Plug one end of the HDMI/DisplayPort/Mini DisplayPort cable to the
monitor’s HDMI/DisplayPort/Mini DisplayPort jack.
b. Connect the other end of the HDMI/DisplayPort/Mini DisplayPort cable
to your computer's HDMI/DisplayPort/Mini DisplayPort jack.
•
To use the earphone: connect the end with plug type to the monitor’s
earphone jack when an HDMI or DisplayPort signal is fed.
ASUS PA328 Series LCD Monitor
2-3
•
To use the USB 3.0 ports: Take the supplied USB 3.0 cable, and plug
the smaller end (type B) of the USB upstream cable to the monitor’s USB
upstream port, and the larger end (type A) to your computer’s USB 3.0 port.
Make sure your computer is installed with the lastest Windows 7/Windows 8
operating system. That will enable the USB ports on the monitor to work.
When these cables are connected, you can choose the desired signal
from the Input Select item in the OSD menu.
2.4
Turning on the monitor
Press the power button . See page 1-2 for the location of the power button. The
power indicator lights up in white to show that the monitor is ON.
2-4
Chapter 2: Setup
3.1
OSD (On-Screen Display) menu
3.1.1
How to reconfigure
Standard Mode
Splendid
Standard Mode
Color
sRGB Mode
Image
Scenery Mode
Sound
Reading Mode
PIP/PBP Setting
Darkroom Mode
Input Select
User Mode1
System Setup
User Mode2
PA328
DisplayPort 3840 x 2160 @ 30Hz
Shortcut
1.
Press the
2.
Move the
Menu (5-way) button up/down/left/right to navigate through
the functions. Highlight the desired function and press the
Menu (5-way)
button to activate it. If the function selected has a sub-menu, move the
Menu (5-way) button up/down to navigate through the sub-menu functions.
Highlight the desired sub-menu function and press the
Menu (5-way)
button or move the
Menu (5-way) button to activate it.
3.
Move the
Menu (5-way) button up/down to change the settings of the
selected function.
4.
To exit and save the OSD menu, press the
button or move the
Menu
(5-way) left repeatedly until the OSD menu disappears. To adjust other
functions, repeat steps 1-3.
3.1.2
1.
Menu (5-way) button to activate the OSD menu.
OSD function introduction
Splendid
This function contains 7 sub-functions you can select for your preference.
Each mode has the Reset selection, allowing you to maintain your setting or
return to the preset mode.
Standard Mode
Splendid
Standard Mode
Color
sRGB Mode
Image
Scenery Mode
Sound
Reading Mode
PIP/PBP Setting
Darkroom Mode
Input Select
User Mode1
System Setup
User Mode2
PA328
DisplayPort 3840 x 2160 @ 30Hz
Shortcut
ASUS PA328 Series LCD Monitor
3-1
•
Standard Mode: Best choice for document editing with SplendidPlus
Video Enhancement.
•
sRGB Mode: Compatible with sRGB color space, sRGB mode is the best
choice for document editing.
Color
White Point
Primaries
Space
Xw
Yw
Xr
Yr
Xg
Yg
Xb
Yb
sRGB 0.3127 0.329
0.64
0.33
0.3
0.6 0.15 0.06
•
Scenery Mode: Best choice for scenery photo display with SplendidPlus
Video Enhancement.
•
Reading Mode: This is the best choice for book reading.
•
Darkroom Mode: This is the best choice for a weak ambient light
environment.
•
User Mode 1/User Mode 2: More items are adjustable in the color menu.
Function
Brightness
Contrast
Saturation
Hue
Color Temperature
Gamma
Six-axis
Hue
Advanced Six-axis
Saturation
Setting
Gain
Offset
3-2
User
Mode
Standard sRGB Scenery Reading Darkroom 1/
Mode
Mode Mode Mode Mode
User
Mode
2
Yes
Yes
Yes
Yes
Yes
Yes
No
No
No
No
Yes
Yes
No
No
No
No
No
Yes
No
No
No
No
No
Yes
Yes
No
No
No
No
Yes
Yes
No
No
No
No
Yes
No
No
No
No
No
Yes
No
No
No
No
No
Yes
No
No
No
No
No
Yes
No
No
No
No
No
Yes
Chapter 3: OSD (On-Screen Display) menu
2.
Color
Set a desired color setting from this menu.
Standard Mode
Splendid
Brightness
Color
Contrast
Image
Saturation
Sound
Hue
PIP/PBP Setting
Color Temp.
Input Select
Gamma
System Setup
Advanced Setting
Shortcut
Color Reset
PA328
DisplayPort 3840 x 2160 @ 30Hz
•
Brightness: The adjusting range is from 0 to 100.
•
Contrast: The adjusting range is from 0 to 100.
•
Saturation: The adjusting range is from 0 to 100.
•
Hue: Shifts the image color between green and purple.
•
Color Temp.: Contains 4 modes including 9300K, 6500K, 5500K and
5000K.
•
Gamma: Allows you to set the color mode to 2.4, 2.2 or 1.8.
•
Advanced Setting:
•
*
6-axis Hue adjustment.
*
6-axis Saturation adjustment.
*
Adjusts the gain levels for R, G, B.
* Adjusts the black level offset values for R, G, B.
Color Reset:
*
Current Splendid color mode reset:
Resets the color settings of current color mode to the factory
default value.
*
All Splendid color mode reset:
Resets the color settings of all color modes to the factory default
value.
ASUS PB328 Series LCD Monitor
3-3
3.
Image
Set the image related setting from this menu.
Standard Mode
Splendid
Sharpness
Color
Trace Free
Image
Aspect Control
Sound
Uniformity Compensation
PIP/PBP Setting
VividPixel
Input Select
ASCR
PA328
DisplayPort 3840 x 2160 @ 30Hz
System Setup
Shortcut
•
Sharpness: The adjusting range is from 0 to 100.
•
Trace Free: Adjusts the response time of the monitor.
•
Aspect Control: Adjusts the aspect ratio to full, 4:3, 1:1 or OverScan.
4:3 is only available when input source is in 4:3 format. OverScan is only
available for the HDMI input source.
•
Uniformity Compensation: Adjusts different areas of the screen to
reduce any screen uniformy errors, providing consistent brightness and
color across the entire screen.
•
VividPixel: Enhances the outline of the displayed picture and generates
high-quality images on screen.
•
ASCR: Turns on/off the ASCR (ASUS Smart Contrast Ratio) function.
4.
Sound
You can adjust Volume, Mute and Source from this menu.
Standard Mode
Splendid
Volume
Color
Mute
Image
Source
PA328
DisplayPort 3840 x 2160 @ 30Hz
Sound
PIP/PBP Setting
Input Select
System Setup
Shortcut
3-4
•
Volume: the adjusting range is from 0 to 100.
•
Mute: toggles the monitor sound between on and off.
•
Source: decides the monitor sound comes from which source.
Chapter 3: OSD (On-Screen Display) menu
5.
PIP/PBP Setting
The PIP/PBP Setting allows you to open up another sub-window connected
from another video source besides the main-window from your original video
source. By activating this function, you can have two pictures from two
different video sources displayed by the monitor.
Standard Mode
Splendid
PIP/PBP Mode
Color
PIP/PBP Source
Image
PIP Size
Sound
PIP Position
PIP/PBP Setting
SWAP
PA328
DisplayPort 3840 x 2160 @ 30Hz
Input Select
System Setup
Shortcut
•
PIP/PBP Mode: Turns the PIP or PBP function on or off.
•
PIP/PBP Source: Selects the video input source from among HDMI-1/
MHL, HDMI-2, HDMI-3, DisplayPort, and Mini DisplayPort.
•
PIP Size: Adjusts the PIP size to Small, Middle, or Large. (Only available
for the PIP mode)
•
PIP Position: Adjusts the position of the sub-window to Right-Top, LeftTop, Right-Bottom, or Left-Bottom. (Only available for the PIP mode)
•
SWAP: Switches the sources of the main and sub-windows.
Main-window
HDMI-1/
MHL
Subwindow
HDMI-1/MHL
HDMI-2
HDMI-3
DisplayPort
Mini
DisplayPort
ASUS PB328 Series LCD Monitor
HDMI-2
HDMI-3
DisplayPort
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Mini
DisplayPort
Yes
Yes
Yes
Yes
Yes
3-5
6.
Input Select
In this function, you can select your desired input source.
Standard Mode
Splendid
HDMI-1/MHL
Color
HDMI-2
Image
HDMI-3
Sound
DisplayPort
PIP/PBP Setting
Mini DisplayPort
PA328
DisplayPort 3840 x 2160 @ 30Hz
Input Select
System Setup
Shortcut
7.
System Setup
Allows you to adjust the system.
Standard Mode
Splendid Demo Mode
Color
ECO Mode
Image
OSD Setup
Sound
Language
PIP/PBP Setting
DisplayPort
Input Select
Key Lock
System Setup
Power Indicator
Shortcut
More
•
Splendid Demo Mode: Splits the screen into two for Splendid modes
comparison. (Scenery mode only)
•
ECO Mode: reduces power consumption.
•
OSD Setup:
•
3-6
Splendid
PA328
DisplayPort 3840 x 2160 @ 30Hz
*
Adjusts the OSD timeout from 10 to 120 seconds.
*
Enables or disables the DDC/CI function.
*
Adjusts the OSD background from opaque to transparent.
*
Adjusts the OSD rotation.
Language: There are 21 languages for your selection, including English,
French, German, Italian, Spanish, Dutch, Portuguese, Russian, Czech,
Croatian, Polish, Romanian, Hungarian, Turkish, Simplified Chinese,
Traditional Chinese, Japanese, Korean, Thai, Indonesia, Persian.
Chapter 3: OSD (On-Screen Display) menu
•
DisplayPort: Compatibility with graphic card. Select DP 1.1 or DP 1.2 by
graphic card DP version. (3840x2160-60Hz is available at DP 1.2 only.
The best resolution is 3840x2160-30Hz at DP 1.1). Follow the instructions
below to change 4K2K, 30Hz to 4K2K, 60Hz on your PC: In Windows,
right click the desktop and enter the Screen Resolution. Go to Advanced
Settings, and set the refresh rate to 60Hz from 30Hz.
•
Keylock: To disable all function keys. Press the second button from the
top over five seconds to cancel the key lock function.
•
Power Indicator: Turns the power LED indicator on/off.
•
Information: Shows the monitor information.
•
All Reset: “Yes” allows you to restore the default settings.
8.
Shortcut
Defines the functions for Shortcut 1 and 2 buttons.
Standard Mode
Splendid
Shortcut 1
Color
Shortcut 2
PA328
DisplayPort 3840 x 2160 @ 30Hz
Image
Sound
PIP/PBP Setting
Input Select
System Setup
Shortcut
•
Shortcut 1/Shortcut 2: selects a function for Shortcut 1 and 2 buttons.
When a certain function is selected or activated, your shortcut key may not
support. Available function choices for shortcut: Brightness, Contrast, PIP/
PBP Setting, Color Temp., Volume, User Mode 1, User Mode 2.
ASUS PB328 Series LCD Monitor
3-7
3.2
Specificationssummary
Panel Type
Panel size
Max. Resolution
Pixel pitch
Brightness (Typ.)
Contrast Ratio (Typ.)
Contrast Ratio (Max.)
Viewing angle (H/V) CR>10
Display colors
Response time
SplendidPlus Video Enhancement
SplendidPlus selection
Auto adjustment
Color temperature selection
Digital input
Earphone jack
USB 3.0 port
Colors
Power LED
Tilt
Swivel
Height Adjustment
Kensington lock
AC input voltage
Power consumption
Temperature (Operating)
TFT LCD
32.0" (16:9, 81.3 cm) wide screen
3840 x 2160
0.185 mm
350 cd/m2
1000:1
100,000,000:1 (with ASCR on)
178˚/178˚
1.07 B
6 ms (Gray to gray)
Yes
7 video preset modes
Yes
4 color temperatures
HDMI v2.0, HDMI v1.4, DisplayPort v1.2
Yes
Upstream x 1, Downstream x 4
Black
White (On)/Amber (Standby)
+20˚~ -5˚
+60˚~ -60˚
130 mm
Yes
AC: 100~240V
Power On: < 138.3 W*** (Typ.), Standby: < 0.5 W (Typ.),
Power Off: 0 W (Switch off)
0˚C~40˚C
Temperature (Non-operating)
-20˚C~+60˚C
Dimension (W x H x D)
734.4 mm x 615 mm x 240 mm (machine)
847 mm x 552 mm x 350 mm (package)
11.68 kg (Net); 15.74 kg (Gross)
21 languages (English, French, German, Italian,
Spanish, Dutch, Portuguese, Russian, Czech, Croatian,
Polish, Romanian, Hungarian, Turkish, Simplified
Chinese, Traditional Chinese, Japanese, Korean, Thai,
Indonesia, Persian)
HDMI cable, DisplayPort cable (optional), MHL cable
(optional), DisplayPort cable (Mini-DP to DP), Power
cord, USB cable, Quick start guide, Warranty card,
Support CD, Cable tie, Color Calibration Testing Report
Energy Star, China Energy Level 1, EPEAT Gold
(optional), UL/cUL, CB, CE, EuP, FCC (Class B), CCC,
BSMI, CU, C-Tick, VCCI, TCO6.0, TUV-GS, TUV-Ergo,
Ukraine, J-MOSS, RoHS, WEEE, PSE, PSB, KCC,
eStandby, Windows 7, 8 & 8.1 WHQL, Mac Compliance**
Weight (Esti.)
Multi-languages
Accessories
Regulation approvals
*Specifications are subject to change without notice.
**Requires Mac OS X v10.x
*** Based on Energy Star 6.0 standard.
3-8
Chapter 3: OSD (On-Screen Display) menu
3.3
Troubleshooting (FAQ)
Problem
Power LED is not ON
The power LED lights amber and there is
no screen image
Screen image is too light or dark
Screen image is not centered or sized
properly
Possible Solution
• Press the button to check if the monitor
is in the ON mode.
• Check if the power cord is properly
connected to the monitor and the power
outlet.
• Check if the power switch is ON.
• Check if the monitor and the computer are
in the ON mode.
• Make sure the signal cable is properly
connected the monitor and the computer.
• Inspect the signal cable and make sure
none of the pins are bent.
• Connect the computer with another
available monitor to check if the computer
is properly working.
• Adjust the Contrast and Brightness
settings via OSD.
• Adjust the H-Position or V-Position
settings via OSD.
Screen image bounces or a wave pattern is • Make sure the signal cable is properly
present in the image
connected to the monitor and the
computer.
• Move electrical devices that may cause
electrical interference.
Screen image has color defects (white does • Inspect the signal cable and make sure
not look white)
that none of the pins are bent.
• Perform All Reset via OSD.
• Adjust the R/G/B color settings or select
the Color Temperature via OSD.
Screen image is blurry or fuzzy
• Adjust the Phase and Clock settings via
OSD.
No sound or sound is low
ASUS PA328 Series LCD Monitor
• Ensure that the HDMI/DisplayPort cable is
properly connected to the monitor and the
computer.
• Adjust the volume settings of both your
monitor and HDMI/DisplayPort device.
• Ensure that the computer sound card
driver is properly installed and activated.
3-9
3.4
Supported operating modes
Resolution
Frequency
Horizontal
Frequency (KHz)
Vertical Frequency . Pixel .
(Hz)
(MHz)
640x350
640x480
640x480
640x480
720x400
800x600
800x600
800x600
800x600
848x480
1024x768
1024x768
1024x768
1152x864
1280x720
1280x768
1280x768
1280x800
1280x960
1280x1024
1280x1024
70(N)
59.94(N)
72.82(N)
75.00(N)
70.08(P)
56.25(P)
60.32(P)
72.12(P)
75.00(P)
60(P)
60.00(N)
70.069(N)
75.00(N)
75.00(P/N)
60
60(N)
75(P)
60(P)
60.00(N)
60.02(P)
75.02(P)
31.47(P)
31.47(N)
37.87(N)
37.5(N)
31.47(N)
35.16(P)
37.88(P)
48.08(P)
46.86(P)
31.0(P)
48.36(N)
56.476(N)
60.02(N)
67.5(P/N)
44.77(N)
47.8(N)
60.3(P)
49.7(N)
60.00(P)
63.98(P)
79.98(P)
25.18
25.18
31.5
31.5
28.32
36.00
1366x768
59.79(P)
47.712(P)
85.50
1400x1050
60(P)
65.3(N)
121.75
1440x900
59.89(P)
55.94(N)
106.50
1600x1200
60.00(P)
75.00(P)
162.00
1680x1050
60.00(P)
65.29(N)
146.25
1920x1080
1920x1200 (Reduced
Blanking)
1920x1200
60.00(P)
67.5(P)
148.5
59.95(N)
74.038(P)
154
59.885(P)
74.556(N)
193.25
2560x1080
59.978(N)
66.636(P)
181.25
2560x1440
59.951(N)
88.787(P)
241.50
3840x2160
24(P)
52.593(N)
266.75
3840x2160
25
54.786(N)
278.75
3840x2160
30(P)
65.956(N)
338.75
3840x2160
3840x2160 (Reduced
Blanking)
50(P)
111.174(N)
587
60(N)
133.313(P)
533.25
40.00
50.00
49.50
33.75
65.00
75.00
78.75
108.00
74.5
79.5
102.25
84.5
108.00
108.00
135.00
When the monitor is operating in the video mode (ie, not displaying data) using the HDMI
connector, the following high definition modes shall be supported in addition to standard definition
video.
3-10
Chapter 3: OSD (On-Screen Display) menu
Resolution
1920 × 1080p
1920 × 1080i
1440x480P
1440x576P
1280 × 720p
720 × 576p
720 × 480p
640 × 480p(VGA)
720(1440) × 576i
720(1440) × 480i
Vertical Frequency (Hz)
24
50
59.94
60
50
59.94
60
59.94
60
50
50
59.94
60
50
59.94
60
59.94
60
50
59.94
60
Horizontal Frequency (KHz)
27
56.25
67.43
67.5
28.13
33.72
33.75
31.47
31.5
31.25
37.5
44.95
45
31.25
31.47
31.5
31.47
31.5
15.63
15.73
15.75
* Modes not listed in the table may not be supported. For optimal resolution, we recommend that
you choose a mode listed in the table above.
ASUS PA328 Series LCD Monitor
3-11