advertisement
PROJECTION TV RECEIVER
Chassis : J54A(P)C1.5
Model: SP43T8HPX/BOB
PROJECTION TV RECEIVER C O N T E N T S
1.
Precautions
2.
Reference Information
3.
Specifications
4.
Alignment and Adjustments
5.
Troubleshooting
6.
Exploded View and Parts List
7.
Electric Parts List
8.
Block Diagrams
9.
Wiring Diagram
10.
Schematic Diagrams
Precautions
1. Precautions
Follow these safety, servicing and ESD precautions to prevent damage and protect against potential hazards such as electrical shock and X-rays.
1-1 Safety Precautions
1. Be sure that all of the built-in protective devices are replaced. Restore any missing protective shields.
2. When reinstalling the chassis and its assemblies, be sure to restore all protective devices, including: nonmetallic control knobs and compartment covers.
3. Make sure that there are no cabinet openings through which people—particularly children—might insert fingers and contact dangerous voltages. Such openings include the spacing between the picture tube and the cabinet mask, excessively wide cabinet ventilation slots, and improperly fitted back covers.
If the measured resistance is less than 1.0
megohm or greater than 5.2 megohms, an abnormality exists that must be corrected before the unit is returned to the customer.
4. Leakage Current Hot Check (Figure 1-1):
Warning: Do not use an isolation transformer during this test. Use a leakagecurrent tester or a metering system that complies with American National Standards
Institute (ANIS C101.1, Leakage Current for
Appliances), and Underwriters Laboratories
(UL Publication UL1410, 59.7).
5. With the unit completely reassembled, plug the AC line cord directly into the power outlet. With the unit’s AC switch first in the
ON position and then OFF, measure the current between a known earth ground (metal water pipe, conduit, etc.) and all exposed metal parts, including: antennas, handle brackets, metal cabinets, screwheads and control shafts. The current measured should not exceed 0.5 milliamp. Reverse the powerplug prongs in the AC outlet and repeat the test.
DEVICE
UNDER
TEST
TEST ALL
EXPOSED METAL
SURFACES
2-WIRE CORD
ALSO TEST WITH
PLUG REVERSED
(USING AC ADAPTER
PLUG AS REQUIRED)
LEAKAGE
CURRENT
TESTER
(READING SHOULD
NOT BE ABOVE
0.5mA)
EARTH
GROUND
Fig. 1-1 AC Leakage Test
6. Antenna Cold Check:
With the unit’s AC plug disconnected from the
AC source, connect an electrical jumper across the two AC prongs. Connect one lead of the ohmmeter to an AC prong. Connect the other lead to the coaxial connector.
7. X-ray Limits:
The picture tube is especially designed to prohibit X-ray emissions. To ensure continued
X-ray protection, replace the picture tube only with one that is the same type as the original.
Carefully reinstall the picture tube shields and mounting hardware; these also provide X-ray protection.
8. High Voltage Limits:
High voltage must be measured each time servicing is done on the B+, horizontal deflection or high voltage circuits. Correct operation of the X-ray protection circuits must be reconfirmed whenever they are serviced.
(X-ray protection circuits also may be called
“horizontal disable” or “hold-down”.)
Heed the high voltage limits. These include the X–ray Protection Specifications Label, and the Product Safety and X-ray Warning Note on the service data schematic.
Samsung Electronics 1-1
Precautions
1-1 Safety Precautions (Continued)
9. High voltage is maintained within specified limits by close-tolerance, safety-related components and adjustments. If the high voltage exceeds the specified limits, check each of the special components.
10. Design Alteration Warning:
Never alter or add to the mechanical or electrical design of this unit. Example: Do not add auxiliary audio or video connectors. Such alterations might create a safety hazard. Also, any design changes or additions will void the manufacturer’s warranty.
11. Hot Chassis Warning:
Some TV receiver chassis are electrically connected directly to one conductor of the AC power cord. If an isolation transformer is not used, these units may be safely serviced only if the AC power plug is inserted so that the chassis is connected to the ground side of the
AC source.
To confirm that the AC power plug is inserted correctly, do the following: Using an AC voltmeter, measure the voltage between the chassis and a known earth ground. If the reading is greater than 1.0V, remove the AC power plug, reverse its polarity and reinsert.
Re-measure the voltage between the chassis and ground.
12. Some TV chassis are designed to operate with
85 volts AC between chassis and ground, regardless of the AC plug polarity. These units can be safely serviced only if an isolation transformer inserted between the receiver and the power source.
13. Some TV chassis have a secondary ground system in addition to the main chassis ground.
This secondary ground system is not isolated from the AC power line. The two ground systems are electrically separated by insulating material that must not be defeated or altered.
14. Components, parts and wiring that appear to have overheated or that are otherwise damaged should be replaced with parts that meet the original specifications. Always determine the cause of damage or overheating, and correct any potential hazards.
1-2
15. Observe the original lead dress, especially near the following areas: Antenna wiring, sharp edges, and especially the AC and high voltage power supplies. Always inspect for pinched, out-of-place, or frayed wiring. Do not change the spacing between components and the printed circuit board. Check the AC power cord for damage. Make sure that leads and components do not touch thermally hot parts.
16. Picture Tube Implosion Warning:
The picture tube in this receiver employs
“integral implosion” protection. To ensure continued implosion protection, make sure that the replacement picture tube is the same as the original.
17. Do not remove, install or handle the picture tube without first putting on shatterproof goggles equipped with side shields. Never handle the picture tube by its neck. Some
“in-line” picture tubes are equipped with a permanently attached deflection yoke; do not try to remove such “permanently attached” yokes from the picture tube.
18. Product Safety Notice:
Some electrical and mechanical parts have special safety-related characteristics which might not be obvious from visual inspection.
These safety features and the protection they give might be lost if the replacement component differs from the original—even if the replacement is rated for higher voltage, wattage, etc.
Components that are critical for safety are indicated in the circuit diagram by shading,
Use replacement components that have the same ratings, especially for flame resistance and dielectric strength specifications.
A replacement part that does not have the same safety characteristics as the original might create shock, fire or other hazards.
Samsung Electronics
Precautions
1-2 Servicing Precautions
Warning 1 : First read the “Safety Precautions” section of this manual. If some unforeseen circumstance creates a conflict between the servicing and safety precautions, always follow the safety precautions.
Warning 2 : An electrolytic capacitor installed with the wrong polarity might explode.
1. Servicing precautions are printed on the cabinet. Follow them.
2. Always unplug the unit’s AC power cord from the AC power source before attempting to: (a)
Remove or reinstall any component or assembly, (b) Disconnect an electrical plug or connector, (c) Connect a test component in parallel with an electrolytic capacitor.
3. Some components are raised above the printed circuit board for safety. An insulation tube or tape is sometimes used. The internal wiring is sometimes clamped to prevent contact with thermally hot components. Reinstall all such elements to their original position.
4. After servicing, always check that the screws, components and wiring have been correctly reinstalled. Make sure that the portion around the serviced part has not been damaged.
5. Check the insulation between the blades of the
AC plug and accessible conductive parts
(examples: metal panels, input terminals and earphone jacks).
6. Insulation Checking Procedure: Disconnect the power cord from the AC source and turn the power switch ON. Connect an insulation resistance meter (500V) to the blades of the AC plug.
The insulation resistance between each blade of the AC plug and accessible conductive parts
(see above) should be greater than 1 megohm.
7. Never defeat any of the B+ voltage interlocks.
Do not apply AC power to the unit (or any of its assemblies) unless all solid-state heat sinks are correctly installed.
8. Always connect a test instrument’s ground lead to the instrument chassis ground before connecting the positive lead; always remove the instrument’s ground lead last.
9. When some parts inside the optical engine
(except lamp) are damaged, replace the whole optical engine.
Samsung Electronics 1-3
Precautions
1-3 Precautions for Electrostatically Sensitive Devices (ESDs)
1. Some semiconductor (“solid state”) devices are easily damaged by static electricity. Such components are called Electrostatically
Sensitive Devices (ESDs); examples include integrated circuits and some field-effect transistors. The following techniques will reduce the occurrence of component damage caused by static electricity.
2. Immediately before handling any semicon ductor components or assemblies, drain the electrostatic charge from your body by touching a known earth ground. Alternatively, wear a discharging wrist-strap device. (Be sure to remove it prior to applying power— this is an electric shock precaution.)
3. After removing an ESD-equipped assembly, place it on a conductive surface such as aluminum foil to prevent accumulation of electrostatic charge.
4. Do not use freon-propelled chemicals. These can generate electrical charges that damage
ESDs.
5. Use only a grounded-tip soldering iron when soldering or unsoldering ESDs.
6. Use only an anti-static solder removal device.
Many solder removal devices are not rated as
“anti-static”; these can accumulate sufficient electrical charge to damage ESDs.
7. Do not remove a replacement ESD from its protective package until you are ready to install it. Most replacement ESDs are packaged with leads that are electrically shorted together by conductive foam, aluminum foil or other conductive materials.
8. Immediately before removing the protective material from the leads of a replacement ESD, touch the protective material to the chassis or circuit assembly into which the device will be installed.
9. Minimize body motions when handling unpackaged replacement ESDs. Motions such as brushing clothes together, or lifting a foot from a carpeted floor can generate enough static electricity to damage an ESD.
1-4 Samsung Electronics
Reference Information
A
Ah
Å dB dBm kg kHz k Ω km
Hz h ips kWh
°C
°F
°K
F g
H
G
GHz km/h kV kVA kW
I
MHz
2. Reference Information
2-1 Tables of Abbreviations and Acronyms
Table 2-1 Abbreviations
Ampere
Ampere-hour
Angstrom
Decibel
Decibel Referenced to One
Milliwatt
Degree Celsius
Degree Fahrenheit degree Kelvin
Farad
Gauss
Gigahertz
Gram
Henry
Hertz
Hour
Inches Per Second
Kilowatt-hour
Kilogram
Kilohertz
Kilohm
Kilometer
Kilometer Per Hour
Kilovolt
Kilovolt-ampere
Kilowatt
Liter
Megahertz mH mI mm ms mV nF
Ω pF
µs
µW mA mg
µA
µF
µH
µm
MV
MW
M Ω m
V
VA
W
Wh
Ib rpm rps s
Megavolt
Megawatt
Megohm
Meter
Microampere
Microfarad
Microhenry
Micrometer
Microsecond
Microwatt
Milliampere
Milligram
Millihenry
Milliliter
Millimeter
Millisecond
Millivolt
Nanofarad
Ohm
Picofarad
Pound
Revolutions Per Minute
Revolutions Per Second
Second (Time)
Volt
Volt-ampere
Watt
Watt-hour
Samsung Electronics 2-1
Reference Information
FBP
FBT
FF
FM
DVM
EIA
ESD
ESD
CATV
CB
CCD
CCTV
Ch
CRT
CW
DC
FS
GND
G-Y
H
HF
HI-FI
IC
IC
IF
ANSI
APC
APC
A/V
AVC
BAL
BPF
B-Y
ABL
AC
ACC
AF
AFC
AFT
AGC
AM
Table 2-2 Table of Acronyms
Automatic Brightness Limiter
Alternating Current
Automatic Chroma Control
Audio Frequency
Automatic Frequency Control
Automatic Fine Tuning
Automatic Gain Control
Amplitude Modulation
American National Standards Institute
Automatic Phase Control
Automatic Picture Control
Audio-Video
Automatic Volume Control
Balance
Bandpass Filter
Blue-Y
Community Antenna Television (Cable TV)
Citizens Band
Charge Coupled Device
Closed Circuit Television
Channel
Cathode Ray Tube
Continuous Wave
Direct Current
Digital Volt Meter
Electronics Industries Association
Electrostatic Discharge
Electrostatically Sensitive Device
Feedback Pulse
Flyback Transformer
Flip-Flop
Frequency Modulation
Fail Safe
Ground
Green-Y
High
High-Frequency
High Fidelity
Inductance-Capacitance
Integrated Circuit
Intermediate Frequency
SW
TP
TTL
TV
UHF
UL
UV
VCD
RC
RF
R-Y
SAP
SAW
SIF
SMPS
S/N
VCO
VCXO
VHF
VIF
VR
VTR
VTVM
TR
NEC
NTSC
OSD
PCB
PLL
PWM
QIF
R
I/O
L
L
LED
LF
MOSFET
MTS
NAB
Input/output
Left
Low
Light Emitting Diode
Low Frequency
Metal-Oxide-Semiconductor-Field-Effect-Tr
Multi-channel Television Sound
National Association of Broadcasters
National Electric Code
National Television Systems Committee
On Screen Display
Printed Circuit Board
Phase-Locked Loop
Pulse Width Modulation
Quadrature Intermediate Frequency
Right
Resistor & Capacitor
Radio Frequency
Red-Y
Second Audio Program
Surface Acoustic Wave(Filter)
Sound Intermediate Frequency
Switching Mode Power Supply
Signal/Noise
Switch
Test Point
Transistor Transistor Logic
Television
Ultra High Frequency
Underwriters Laboratories
Ultraviolet
Variable-Capacitance Diode
Voltage Controlled Oscillator
Voltage Controlled Crystal Oscillator
Very High Frequency
Video Intermediate Frequency
Variable Resistor
Video Tape Recorder
Vacuum Tube Voltmeter
Transistor
2-2 Samsung Electronics
Reference Information
2-2 IC Line Up
No.
1
Block Name
2 SCALER MODULE
3
Samsung Electronics
MAIN
CG MODULE
Table 2 - 3 IC Line - Up
IC Location
IC02
IC17
IC06
IC01
IC13
IC05
IC07
C03
IC09, IC10, IC11,IC14
IC12
IC04, IC15, IC16
IC11
IC01A
IC04
IC08
IC602
IC13
IC06
IC05
IC702
IC605
IC704
IC705
IC703
IC802
IC101
IC701
IC Name
TEA5114A
7905
PCF8574
TEA6425D
TEA6425D
TEA6422D
PCF8591T
PCF8591T
MSP3411G-QA-B8V3/MSP3452G(Option)
74HC123
7027
LF18CDT
78RM33D
VSP9407B-B11
CXA2165Q
74HC4052
NC7SB3157P6X
24C64
EL2250CS
7042
78RM33D
TLC2932IPWLE
TSC87251G2D-OTP
SDC12
TL072C
KA324D
7S04
2-3
Reference Information
No.
4
5
Block Name
MICOM MODULE
SUB
Table 2 - 3 IC Line - Up (Continued)
IC Location
IC902
IC903
IC901
IC904
IC905
IC431, IC471
IC841
IC851
ICS801
IC402
ICZ03, ICZ04
IC831S
IC301
IC Name
24C16
78RM33D
SDA5550M
7025
M27W201-80F6
MC4558C
78R05
SE110N
VIPER12A
DDRI1001
STK392-010
STR-X6459A
LA7845
2-4 Samsung Electronics
2-3 MICOM IIC BUS LINE -UP
/ MSP3452G(Option)
Reference Information
Samsung Electronics 2-5
MENO
2-6 Samsung Electronics
3. Specifications
Broadcasting System
Scanning System
Tuning Range
Antenna Impedance
Intermediate Frequency
Sound Output
Rated Voltage
High Voltage
FUSE
Power Consumption
CW : EURO Multi (PAL, SECAM-B/G, D/K, I, L/L)
CS : PAL Multi (PAL, SECAM-B/G, D/K, I, NT4, 43, NT3.58)
100Hz / Progressive
VHF : CH2 ~ CH12
UHF : CH21 ~ CH69
Cable : CHS1 ~ S40
75 ohm Unbalanced
System
B/G
D/K
I
L(L’)
Video(MHz)
38.90
38.90
38.90
34.5(41.0)
Sound(MHz)
33.40
32.40
32.90
41.0(34.5)
MAX : 15W x 2 ( 8ohm )
AC220V / Free Voltage ( Option )
29KV
250V/6.3A
CODE NO : 3601-000300
230W
Specifications
Samsung Electronics 3-1
❏ White Balance (Southeast Asia)
Fixed
ITEM
HIGHT
LOW
R-CUT OFF
G-CUT OFF
B-CUT OFF
R-DRIVE
G-DRIVE
B-DRIVE
SUB-BRIGHT
SUB-CONTRAST
SUB COLOR
COL AXIS
42W5 x y Y
47W1 x y Y
43T6/43T7 x y Y
290 304 10.5
290 304 9.5
290 304 10
258 254 0.45
258 254 0.35
258 254 0.4
31
16
6
12
15
20
21
42
15
2
16
20
26
48
31
28
10
4
15
2
31
26
7
13
15
20
23
41
15
2
48T6 x y Y
290 304 9.5
258 254 0.4
7
6
31
21
17
20
32
54
15
2
42W5 x y Y
42W5 x y Y
290 304 8.5
290 304 6.5
258 254 0.35
258 254 0.35
31
25
8
11
16
20
29
46
15
2
31
15
9
11
12
20
35
41
15
2
❏ White Balance (Australia)
ITEM
HIGHT
LOW
R-CUT OFF
G-CUT OFF
B-CUT OFF
R-DRIVE
G-DRIVE
B-DRIVE
SUB-BRIGHT
SUB-CONTRAST
SUB COLOR
COL AXIS
42W5 x y Y
47W1 x y Y
43T6/43T7 x y Y
290 304 10.5
290 304 9.5
290 304 10
290 290 0.45
290 290 0.35
590 290 0.4
31
20
8
10
21
20
21
35
10
1
22
20
23
38
31
25
9
6
10
1
31
26
8
13
22
20
21
36
10
1
48T6 x y Y
290 304 9.5
290 290 0.4
5
8
31
24
22
20
25
45
10
1
42W5 x y Y
42W5 x y Y
290 304 8.5
290 304 6.5
290 290 0.35
290 290 0.35
31
29
7
10
22
20
22
41
10
1
31
17
15
11
19
20
23
32
10
1
3-2 Samsung Electronics
Alignment and Adjustments
4. Alignment and Adjustments
4-1 When entering the service mode;
1. Turn on the TV, and then select “DYNAMIC” on the picture adjustment mode.
2. Turn off the TV(STAND-BY).
3. Enter the service mode by pressing the remote control keys in the following sequence:
Display -> Menu -> Mute -> Power ON
Note : If necessary, re-do steps 1~3.
Initial display when the service mode is switched.
4-1-1 WHEN A RF SIGNAL IS RECEIVED
CW MODEL
DEFLECTION
VIDEO ADJUST 1
VIDEO ADJUST 2
VIDEO ADJUST 3
VIDEO ADJUST 4
OPTION (87h 05ch)
YC DELAY
RESET
SIM-814EW YY.MM.DD
CS MODEL
DEFLECTION
VIDEO ADJUST 1
VIDEO ADJUST 2
VIDEO ADJUST 3
VIDEO ADJUST 4
OPTION (D8 O4 2E)
YC DELAY
RESET
T_CADEC_010 YY.MM.DD
4-1-2 SERVICE MODE CONTROL KEYS
MAIN MENU
UP / DOWN
RIGHT / LEFT
MENU DISPLAY
Select item by moving cursor
Decrease or increase the adjustment values
[Navigation Key]
✍
PRECAUTIONS
1. When EEPROM IC (IC902) is replaced, first connect the power cord and wait for about 4~5 seconds.
2. After replacing EEPROM IC (IC902), enter the Service mode. Next, enter the standard data or the previous EEPROM IC data before replacement. And then check and adjust any items related to
Geometric, Picture, Option.
Samsung Electronics 4-1
Alignment and Adjustments
4-2 FACTORY MODE MENU
4-2-1 CW MODEL(SIM-814EW)
4-2-1(A) DEFLECTION
Item
V Amp
V Shift
H EW
H Shift
V Linearity
Upper Linearity
Lower Linearity
V SC
H Parabolra
Upper Corner
Lower Corner
H Trapezium
Bow
Angle
V Position
Up UCG
Lo UCG
CXA Left Blk
CXA Right Blk
Range
0 ~ 63
0 ~ 63
0 ~ 63
0 ~ 63
0 ~ 63
0 ~ 63
0 ~ 63
0 ~ 3
0 ~ 63
0 ~ 63
0 ~ 63
0 ~ 63
0 ~ 15
0 ~ 15
0 ~ 15
0 ~ 15
0 ~ 3
0 ~ 63
0 ~ 63
Initial Data
31
31
0
29
36
34
21
31
0
50
25
0
0
7
39
32
41
24
7
Remark
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
Variable
FIX
Variable
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
4-2 Samsung Electronics
4-2-1(B) VIDEO ADJUST1
Item
R Cutoff
G Cutoff
B Cutoff
Color On/Off
CB Offset
CR Offset
R Drive
G Drive
B Drive
Sub Bright
Sub Contrast
Sub Color
Sut Tint
CTI Level
COL Axis
LTI Level
VSU
Melody Volume
LIT Mode
System
Range
0 ~ 63
0 ~ 63
0 ~ 15
0 ~ 23
0 ~ 63
0 ~ 3
0 ~ 3
0 ~ 3
0 ~ 63
0 ~ 63
0 ~ 63
0 ~ 1
0 ~ 63
0 ~ 63
0 ~ 63
0 ~ 63
0 ~ 15
0 ~ 20
0 ~ 3
0 ~ 3
Initial Data
1
1
3
31
1
25
15
8
1
1
2
4
1
31
31
25
25
25
25
25
Alignment and Adjustments
Remark
Variable
FIX
Variable
Variable
Variable
Variable
Variable
FIX
Variable
Variable
Variable
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
Samsung Electronics 4-3
Alignment and Adjustments
4-2-1(C) VIDEO ADJUST2
Item
ABL Level
Gamma
DPIC Level
DC Trans
ABL TH
VM Level
VM Corint
VM f0
VM Limit
VM Delay
SHP CD
SHP f0
SHP f1 & P/O
AKB Time
BandPass 9407
HighPass 9407
S ABL
P ABL
Range
0 ~ 3
0 ~ 3
0 ~ 3
0 / 1
-
0 ~ 63
-
-
0 ~ 3
0 ~ 15
0 ~ 3
0 ~ 3
0 ~ 3
0 ~ 3
0 ~ 15
0 ~ 3
0 ~ 15
0 ~ 3
Initial Data
1
11
13
24
40
0
15
1
1
0
1
0
1
15
1
3
1
2
Remark
FIX
FIX
FIX
-
FIX
FIX
FIX
FIX
FIX
-
-
FIX
FIX
FIX
FIX
-
FIX
FIX
4-4 Samsung Electronics
4-2-1(D) VIDEO ADJUST3
Item
H Comp
V Comp
Pin Comp
AFC Comp
H-Sync Phase
NR Off Value
CG HAO
CG VAO
NR High Ref
NR Low Ref
NR High Value
NR Low Value
NR Hight Ref(S)
NR Low Ref(s)
NR High Value(S)
NR Low Value(S)
NR Read M/S
Range
0 ~127
0 ~127
0 ~255
0 ~255
0 ~127
0 ~127
0 ~255
0 ~255
0/27
0 ~ 15
0 ~ 15
0 ~ 7
0 ~ 7
0 / 1
0 ~ 9
0 ~ 20
0 ~ 20
Initial Data
51
20
0
17
40
3
17
51
0 0
6
10
0
0
15
1
4
3
Alignment and Adjustments
Remark
FIX
Samsung Electronics 4-5
Alignment and Adjustments
4-2-1(E) VIDEO ADJUST4
Item
SECAM Color Main
SECAM Color Pip
Picture Limit
OSD Contrast
TTX Contrast
Range
0 ~255
0 ~255
0 ~ 3
0 ~ 15
0 ~ 15
4-2-1(F) OPTION
Item
SYSTEM
SOUND
ASPECT
WIDE 4:3
X-RAY
AUTO FM
PIP
LNA
Letter Box
D/W PIP
AGC
Natural Zoom
HELP
Initial Data
28
28
3
10
3
Setting Data
CS/CW
A2-NICAM/Virtual Dolby
WIDE / 4:3
OFF / ON
OFF / ON
OFF / ON
OFF / 2-TUNER
OFF / ON
OFF / ON
OFF / ON
OFF / ON
OFF / ON
OFF / ON
Appliance
OFF
ON
ON
On
ON
OFF
CW
Virtual Dolby
WIDE on
ON
ON
2-TUNER
Remark
FIX
Remark
4-6 Samsung Electronics
4-2-1(G) YC DELAY
Item
P.YC(AV) Delay
S.YC(AV) Delay
N.YC(AV) Delay
P.BG.YC Dealy
P.DK.YC Delay
P.I.YC Delay
P.M.YC Delay
P.N.YC Delay
S.BG.YC Delay
S.DK.YC Delay
S.I.YC Delay
S.M.YC Delay
S.L.YC Delay
N.M.YC Delay
N4.43 YC Delay
Range
-7
-10
3
-6
-7
-9
-9
0
0
1
-2
0
1
-5
1
Alignment and Adjustments
Samsung Electronics 4-7
Alignment and Adjustments
4-2-2 CS MODEL(T_CADEC_010)
4-2-2(A) DEFLECTION
Item
V Amp
V Shift
H EW
H Shift
V Linearity
Upper Linearity
Lower Linearity
V SC
H Parabolra
Upper Corner
Lower Corner
H Trapezium
Bow
Angle
V Position
Up UCG
Lo UCG
CXA Left Blk
CXA Right Blk
Initial Data
Range
0
50
25
31
31
31
0
15
33
33
18
0
2
7
0
0 ~ 63
0 ~ 63
0 ~ 63
0 ~ 63
0 ~ 63
0 ~ 63
0 ~ 63
0 ~ 3
0 ~ 63
0 ~ 63
0 ~ 63
0 ~ 63
0 ~ 15
0 ~ 15
0 ~ 15
0 ~ 15
0 ~ 3
0 ~ 63
0 ~ 63
42W5 47W1 43T6/43T7 48T6 54T6 62T6
NTSC PAL NTSC PAL NTSC PAL NTSC PAL NTSC PAL NTSC PAL
48
31
48
24
48
31
48
24
48
31
48
24
48
31
48
24
48
31
48
24
48
31
48
24
48
31
48
24
48
31
48
24
48
31
48
24
48
31
48
24
48
31
48
24
48
31
48
24
7
0
0
2
15
33
33
18
31
31
31
0
0
50
25
7
0
0
2
15
33
33
18
31
31
31
0
0
50
25
7
0
0
2
15
33
33
18
31
31
31
0
0
50
25
0
50
25
31
31
31
0
15
33
33
18
0
2
7
0
0
50
25
31
31
31
0
15
33
33
18
0
2
7
0
Remark
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
Variable
FIX
Variable
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
4-8 Samsung Electronics
4-2-2(B) VIDEO ADJUST1
Item
R Cutoff
G Cutoff
B Cutoff
Color On/Off
CB Offset
CR Offset
R Drive
G Drive
B Drive
Sub Bright
Sub Contrast
Sub Color
Sut Tint
CTI Level
COL Axis
LTI Level
VSU
Melody Volume
LIT Mode
System
Range
0 ~ 63
0 ~ 63
0 ~ 15
0 ~ 23
0 ~ 63
0 ~ 3
0 ~ 3
0 ~ 3
0 ~ 63
0 ~ 63
0 ~ 63
0 ~ 1
0 ~ 63
0 ~ 63
0 ~ 63
0 ~ 63
0 ~ 15
0 ~ 20
0 ~ 3
0 ~ 3
Initial Data
1
2
3
31
1
25
15
8
1
1
2
4
1
31
31
25
25
25
25
25
Alignment and Adjustments
Remark
Variable
Variable
Variable
Variable
Variable
Variable
Variable
Variable
Variable
Variable
Variable
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
Samsung Electronics 4-9
Alignment and Adjustments
4-2-2(C) VIDEO ADJUST2
Item
ABL Level
Gamma
DPIC Level
DC Trans
ABL TH
VM Level
VM Corint
VM f0
VM Limit
VM Delay
SHP CD
SHP f0
SHP f1 & P/O
AKB Time
BandPass 9407
HighPass 9407
S ABL
P ABL
Range
0 ~ 3
0 ~ 3
0 ~ 3
0 / 1
-
0 ~ 63
-
-
0 ~ 3
0 ~ 15
0 ~ 3
0 ~ 3
0 ~ 3
0 ~ 3
0 ~ 15
0 ~ 3
0 ~ 15
0 ~ 3
Initial Data
1
11
13
24
40
0
15
1
1
0
1
0
1
15
1
3
1
2
Remark
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
4-10 Samsung Electronics
4-2-2(D) VIDEO ADJUST3
Item
H Comp
V Comp
Pin Comp
AFC Comp
H-Sync Phase
NR Off Value
CG HAO
CG VAO
NR High Ref
NR Low Ref
NR High Value
NR Low Value
NR Hight Ref(S)
NR Low Ref(s)
NR High Value(S)
NR Low Value(S)
NR Read M/S
Range
0 ~127
0 ~127
-
-
0 ~127
0 ~127
-
-
-
0 ~ 15
0 ~ 15
0 ~ 7
0 ~ 7
0 / 1
-
0 ~ 20
0 ~ 20
Initial Data
51
20
0
17
40
3
17
51
0 0
6
10
0
0
15
1
4
3
Alignment and Adjustments
Remark
FIX
Samsung Electronics 4-11
Alignment and Adjustments
4-2-1(E) VIDEO ADJUST4
LANGUAGE
SOUNG
CRT
CHANNEL
X-LAY
TTX
AUTO FM
PIP
MULTI PIP
LNA
HIGH DEV
SCART
LETTER BOX
DW PIP
LIST PRIOR
Item
SECAM Color Main
SECAM Color Pip
Picture Limit
OSD Contrast
TTX Contrast
4-2-1(F) OPTION
Item
TTX LANG
AGC
AV MEMORY
AUSTRALIA
Range
0 ~255
0 ~255
0 ~ 3
0 ~ 15
0 ~ 15
Initial Data
28
28
3
10
3
Setting Data
ENG+THAI / ENG+CHINA
ENG+MIDDLE / ONLY ENG
A2-NICAM/Virtual Dolby
WIDE / 4:3
100-channel / 200-channel
/250-chanel
OFF / ON
OFF / ON
OFF / ON
OFF / 2-TUNER
OFF / ON
OFF / ON
OFF / ON
RCA+1SCART+DVD / RCA+DVD
OFF / ON
OFF / ON
OFF / ON
WEST EUROPE / EAST EUROPE
RUSSIAN / GREEK-TURKEY
ARABIC / FARSI / AREB-HEBREW
OFF / ON
OFF / ON
OFF / ON
Appliance
(Southeast Asia)
ONLY ENG
ENG+THAI(Thailand)
Virtual Dolby
4:3(Option)
100-channel
ON
ON
ON
2-TUNER
ON
ON
OFF
RCA+1SCART+DVD
ON
OFF
OFF
0N(AUSTRALIA)
WEST EUROPE
OFF
OFF
OFF
4-12
WEST EUROPE
OFF
OFF
OFF
Appliance
(CHINA)
ENG+CHINA
Virtual Dolby
4:3(Option)
200-channle
ON
OFF
ON
2-TUNER
ON
ON
OFF
RCA+DVD
ON
OFF
OFF
Remark
FIX
Appliance
(Middle East)
ENG+MIDDLE
Virtual Dolby
4:3(Option)
250-channle
ON
ON
ON
2-TUNER
ON
ON
OFF
RCA+1SCART+DVD
ON
OFF
OFF
ARABIC
OFF
OFF
OFF
Samsung Electronics
4-2-2(G) YC DELAY
Item
P.YC(AV) Delay
S.YC(AV) Delay
N.YC(AV) Delay
P.BG.YC Dealy
P.DK.YC Delay
P.I.YC Delay
P.M.YC Delay
P.N.YC Delay
S.BG.YC Delay
S.DK.YC Delay
S.I.YC Delay
S.M.YC Delay
S.L.YC Delay
N.M.YC Delay
Range
-9
-7
-10
3
0
-7
-9
-2
0
1
1
0
1
-5
Alignment and Adjustments
Samsung Electronics 4-13
Alignment and Adjustments
4-3 Screen Change (When Adjusting I 2 C Bus Geometric Items)
1 V AMP 6 V - S - CORRECTION
2 V SHIFT
3 H EW
7 H Parabolra
8 H Trapezium
4 H SHIFT
5 V LINEARITY
9 BOW
10 ANGLE
4-14 Samsung Electronics
Alignment and Adjustments
4-4 Other Adjustments
4-4-1 Screen Adjustment
1. Warm up the TV for at least 30 minutes.
3. Trun to the Video Mode(No Signal) using a remote-control.
4. Connect an oscilloscope to RK, GK, BK.
5. Adjust the VR (VR501, VR531, VR561) screen so that RK, GK, BK pulse is 20Vp-p each.
(Turn the R,G,B VR screen fully counterclockwise in the area of each flyback line.)
4-4-2 White Balance Adjustment keys in the following sequence :
Displsy → Menu → Mute → Power ON
3. Select Sub-Bright by pressing the Volume +/keys.
4. Adjust so that the 63 step on the right side of the screen is not seen (Use the Volume +/keys).
5. Press the Menu key to exit.
4-4-4 High Voltage (30KV) Check
PRECAUTION
1. Input a lion head pattern.
2. Input 100% white pattern.
3. In the stand-by mode, press the remote-control keys in the following sequence:
Displsy
→ Menu → Mute → Power ON
4. Warm up the TV for at least 30 minutes.
5. Input a 10-step signal.
6. R-cut off, B-cut off, and G-cut off by pressing the Volume +/- keys.
7. Adjust the low light with viewing the dark side of the screen.
8. Select R-drive, G-drive and B-drive by pressing the Volume +/- keys.
9. Adjust the high light with viewing the light side of the screen.
10. If necessary, redo adjustments 6~9.
11. Press the Menu key to exit.
4-6-3 Sub-Brightness Adjustment
1. Input a sub-brightness adjustment signal.
(TOSHIBA PATTERN)
2. In the stand-by mode, press the remote-control
3. Warm up the TV for at least 10 minutes.
4. Use a digital multimeter.
ADJUSTMENT
1. Connect the (+) terminal of the digital multimeter to Q471 and the (-) terminal to
Q401 (located on the deflection board).
2. Adjust RR471S (located on the sub board) so that the digital meter indicates
DC290V ± 0.1V.
4-4-5 F.S. (Fail Safe) Circuit Check
(GT430,GT431)
Note : The F.S. Circuit check must be performed after servicing.
1. Turn on the TV.
3. Short F/S Test point (located on the SUB PCB).
Then, both sound and picture disappear.
(Note: Even if the shorted terminals are removed, both sound and picture do not appear. This proves the F.S.
circuit is working. )
4. To restore both sound and picture, turn off the
TV and reset it after about 30 seconds.
Samsung Electronics 4-15
Alignment and Adjustments
4-4-6 Static Focus Adjustment
PRECAUTION
2. Input a crosshatch pattern.
3. Cover the lenses that are not being adjusted.
4. Connect a convergence jig and read data.
5. Adjust the lens for best focus.
(See Fig, 4-1)
STATIC FOCUS (CONTINUED)
Vary the focus pack VR (Red, Blue) on the front cabinet. Adjust the TV for best possible focus around the center of the crosshatch pattern, without losing overall screen balance.
Figure Crosshatch Pattern
Examine these points together.
4. When the lens is turned clockwise, the color aberration will change as follows:
Lens Color Aberration Change
R Orange - Crimson
G Blue - Red
B Purple - Green
5. Green lens adjustment:
Set the lens at the point where Blue just changes to Red. If the color aberration is irregular throughout the picture screen, adjust the lens to show Red color aberration
(approximately 1~3 mm area) within a 3-block grid around the horizontal center-line. If the color aberration is irregular, adjust the lens as shown in the diagram below. (Accurate alignment of Green is important for overall color quality.)
Set the Red lens at the point where Orange becomes Crimson.
7. Blue lens adjustment
Set the Blue lens at the point where Purple becomes Green.
P
L1 L2
Examine these points together
Fig. 4-1 Crosshatch Pattern.
4-4-7 Lens Focus Adjustment
PRECAUTIONS
1. Do this adjustment after the static focus adjustment and the tilt adjustment.
(Contrast:100, Brightness:50)
3. Input a crosshatch pattern.
ADJUSTMENT
1. Loosen the lens screws.
2. Cover the two lenses that are not being adjusted.
3. Adjust the lens, observing the color aberration vertically and horizontally within 3 blocks of the center of the crosshatch pattern.
4-16
RED ABERRATION BLUE ABERRATION
L1, L2 < P
Fig. 4-2 Color Aberration
Samsung Electronics
Alignment and Adjustments
4-5 Beam alignment Adjustments
1. Select the “DYNAMIC” video mode.
2. Warm up the set at least for 10 minutes.
3. Enter the Convergence mode by pressing the remote control buttons in the following sequence :
Mute
4. Set the Beam Alignment Adjustment CY to Zero magnetic field area.
(Creation of CPM Zero Magnet) (Creation of the 2-pole/4-pole zero magnets)
5. Check the squarewave at the point where the focus is misaligned.
6. Press the button on the remote control during 3~5 sec and vibrating dot-pattern appears.
7. Adjust the Focus-pack VR for defocusing.
8. Mute the other patterns (R/B) other than G-PATTERN.
G-FOCUS CORE
G-FOCUS
(Varying G-Focus Pack)
CORE
Varying the 2-pole of VM
(Positioning the Core in the Center)
(When VM 2-Pole Adjustment is completed)
Varying the 4-pole of VM
(Adjust until the light around the core becomes a circle)
9. Adjust the 2, 4 polarities of VM-COIL as shown in figure below.
10. Adjust the G-Focus until any light around the core disappears.
11. Adjust G-Focus so that the surrounding flash can disappear from the spot.
12. After G-Focus adjustments are complete, adjust R-Focus as above procedures.
13. The B-CRT adjustments can be omitted because the variance of beam focus is small.
(Only Vm-coil is mounted.)
14. Adjust the Focus-pack VR for fine focusing.
15. Press the button on the remote control, and the mode changes to the Convergence Adjustment mode.
S.STD
16. Press the button on the remote control to return to normal viewing.
Samsung Electronics 4-17
Alignment and Adjustments
4-6 SCREEN-JIG
4-6-1 42W5
42W5 Screen Size : X 932, Y 524 (X:764 = 22 x 2 + 60 x 12, Y:262 = 17 x 2 + 38 x 6)-PAL MODE
2 6 .8 4 m m 7 3 .1 9 m m 2 6 .8 4 m m
3 4 .0 0 m m
7 6 .0 0 m m
3 4 .0 0 m m
4-6-2 47W3
47W3 Screen Size : X 1045, Y 588 (X:764 = 22 x 2 + 60 x 12, Y:262 = 17 x 2 + 38 x 6)-PAL MODE
3 0 .0 9 m m 8 2 .0 7 m m 3 0 .0 9 m m
8 5 .2 8 m m
4-18
3 8 .1 5 m m
Samsung Electronics
Alignment and Adjustments
4-6-3 55W3
55W3 Screen Size : X 1225, Y 686 (X:764 = 22 x 2 + 60 x 12, Y:262 = 17 x 2 + 38 x 6)-PAL MODE
3 5 .2 7 m m 9 6 .2 0 m m 3 5 .2 7 m m
4 4 .5 1 m m
9 9 .5 0 m m
4 4 .5 1 m m
4-6-4 65W3
65W3 Screen Size : X 1442, Y 838 (X:764 = 22 x 2 + 60 x 12, Y:262 = 17 x 2 + 38 x 6)-PAL MODE
4 1 .5 2 m m 1 1 3 .2 5 m m 4 1 .5 2 m m
1 2 1 .5 4 m m
5 4 .3 7 m m
Samsung Electronics 4-19
Alignment and Adjustments
4-6-5 43T6/43T7
43T6 Screen Size : X 885, Y 666 (X:764 = 22 x 2 + 60 x 12, Y:262 = 17 x 2 + 38 x 6)-PAL MODE
2 5 .4 8 m m 6 9 .5 0 m m 2 5 .4 8 m m
4 3 .2 1 m m
9 6 .6 0 m m
4 3 .2 1 m m
4-6-6 48T6
48T6 Screen Size : X 973.4 Y 738.4 (X:764 = 22 x 2 + 60 x 12, Y:262 = 17 x 2 + 38 x 6)-PAL MODE
2 8 .0 3 m m 7 6 .4 5 m m 2 8 .0 3 m m
1 0 7 .1 0 m m
4-20 Samsung Electronics
Alignment and Adjustments
4-6-5 54T6
54T6 Screen Size : X 1099 Y 823 (X:764 = 22 x 2 + 60 x 12, Y:262 = 17 x 2 + 38 x 6)-PAL MODE
3 1 .6 5 m m 8 6 .3 1 m m 3 1 .6 5 m m
1 1 9 .3 7 m m
4-6-6 62T6
62T6 Screen Size : X 1259.4, Y 948 (X:764 = 22 x 2 + 60 x 12, Y:262 = 17 x 2 + 38 x 6)-PAL MODE
3 6 .2 7 m m 9 8 .8 1 m m 3 6 .2 7 m m
1 3 7 .5 0 m m
6 1 .5 1 m m
Samsung Electronics 4-21
Alignment and Adjustments
4-7 Remote Control for Servicing(Convergence Mode)
Power
TV VCR Cable DVD SET
Convergence Data
LINE Adjust
ENTIRE Adjust
G-Mute
R-Mute
B-Mute
Exit Button
Convergence Data
Left/Right Move Button
Surround S.STD
P.STD
TV
S.Mode
Mute
VOL
Menu
P
Still
Video
Last Data Save button/Canccel
Cg Factory Data
Select Key(Each Inch)
R-Selete
B-Selete
G-Selete
Save Button
Convergence Data
UP/DOWN Move Button
Test Normal
Convergence H-PHASE
Move Button(Left)
Convergence Data
UP/DOWN Move Button
Display P.Size
Text/Mix
PIP
ON
Info.
Sleep Perfect Focus
Scan Swap Locate
Convergence H-PHASE
Move Button(Right)
4-22 Samsung Electronics
4-7-1 KEY Function
1. R-SELECT
Press to select RED color.
2. G-SELECT
Press to select GREEN color.
3. B-SELECT
Press to select BLUE color.
4. R-MUTE
Press to mute RED color.
5. G-MUTE
Press to mute GREEN color.
6. B-MUTE TV
Press to mute BLUE color.
7. CANCEL KEY
Press to revert to the previous data during the Convergence Adjustment.
Display
8. TEST/NORMAL
Press to check TV mode in the Convergence Mode.
Press to move a line up/down or left/right.
10. FACTORY DATA SELECT BUTTON
Press to call the factory default values.
S.Mode
11. SAVE BUTTON
After the Convergence Adjustments are completed, press to save data.
S.STD
12. EXIT BUTTON
After the Convergence adjustments are completed, press to exit to TV mode.
Alignment and Adjustments
Samsung Electronics 4-23
Alignment and Adjustments
13. CURSOR MOVE BUTTON
Press to move the cursor up/down or right/left.
!
UP
LEFT RIGHT
DOWN
@
UP DOWN LEFT RIGHT
# (Mute) Press to move the cursor left or up.
(Video) Press to move the cursor right or down.
(Menu) Press switch the cursor direction horizontally or vertically.
14. CONVERGENCE PICTURE MOVE BUTTON
(Right)
VOL
(Left)
P
(Up)
(Down)
Cg -Data Move Button
15. CONVERGENCE MOVE BUTTON
PIP
ON
Sleep
Press to move the convergence right ( ) or left ( ) .
16. CONVERGENCE DATA ZERO BUTTON
Press to zero the convergence correction data.
4-24 Samsung Electronics
Alignment and Adjustments
42” (42W5)
47” (47W3)
55” (55W3)
43” (43T6
43” (43T7)
48” (48T6)
54” (54T6)
62” (62T6)
65”(65W3)
17. INITIAL DATA SET BUTTON
Changes when applying Almighty-Cg, Module (How to extract the basic Cg Data)
Inch (Type)
Model Name
Representative
Model
SP42W5
SP47W3
SP55W3
SP43T6
SP43T7
SP48T6
SP54T6
SP62T6
SP65W3
Basic Data
Number after entring the Cg-Mode
5-425 (Press in regular order)
5-473(Press in regular order)
5-553(Press in regular order)
5-436(Press in regular order)
5-437(Press in regular order)
5-485(Press in regular order)
5-545(Press in regular order)
5-625(Press in regular order)
Screen Display
Locate
18. Data shift Button Press to transmit data(PAL Mode/NTSC Mode).
Samsung Electronics 4-25
Alignment and Adjustments
4-8 Convergence Adjustment
4-8-1 Convergence Adjustment
Special Notes
✏ A sensor is attached on the center of each side of the Convergence Mode pattern
(see figure below). The sensors are required for normal Perfect Focus function.
✏ Use a screen jig to do the convergence adjustments correctly (Especially, perform correct convergence adjustments on the center of each side where a sensor is located.)
✏ Do the convergence adjustments correctly. Otherwise, any Perfect Focus error can happen.
1. Warm up the TV for a least 30 minutes.
2. Input an PAL Signal.(Use an antenna or AV source.)
Make sure that deflection yoke are properly adjusted so that the center of
Green, Red, Blue pattern is aligned on the center of screen jig.
3. Enter the Convergence Mode by Pressing the remote control keys in the following sequence:
Mute
S.STD
If OSD displayed as shown in figure below, press the key to exit.
Then, redo step 3 to enter the Convergence Mode.
After entering the Convergence Mode, Stand by for about five seconds before doing the adjustments.
4-26 Samsung Electronics
Menu
Mute
Menu
P.Size
TV
TV
Alignment and Adjustments or
Samsung Electronics or
4-27
Alignment and Adjustments
LINE Adjust
S.Mode
VOL P
4-28
Menu
Samsung Electronics
12.
13.
14.
15.
S.Mode
Alignment and Adjustments
TV
Samsung Electronics 4-29
Alignment and Adjustments
4-8-2 Perfect Focus(Factory Mode)
Up, Down
130
245
150
Perfect Focus
Process : 83%
Exit
Left, Right
130
245
150
Perfect Focus
Process : 83%
Exit
S.STD
4-30 Samsung Electronics
4-9 MICOM and Pins Voltage
4-9-1 Pin Layout
GND
N.C
N.C
GND
TTX-CVBS
2.5V
GND
MAIN-AFT
SUB-AFT
KEY2
KEY1
N.C
H-BLK
V-BLK
W.P
SDA2
SCL2
BUS-STOP
SDA1
SCL1
S-RESET
V-MUTE
GND
2.5V
GND
3.3V
DO1
DO4
DO2
DO3
25
26
27
28
29
30
21
22
23
24
17
18
19
20
13
14
15
16
9
10
11
12
7
8
5
6
3
4
1
2
Samsung Electronics
Alignment and Adjustments
2.5V
GND
N.C
XTAL1
XTAL2
N.C
N.C
N.C
N.C
N.C
OSD-F/B
OSD-B
OSD-G
OSG-R
N.C
N.C
N.C
N.C
N.C
A15
A17
A16
N.C
A7
A13
A12
A14
3.3V
GND
2.5V
56
55
54
53
52
51
60
59
58
57
64
63
62
61
68
67
66
65
72
71
70
69
76
75
74
73
80
79
78
77
4-31
Alignment and Adjustments
4-9-2 MICOM MODULE Pins
SDA2
SW3
GND
SW2
SUB-AFT
GND
MAIN-AFT
BUS-STOP
ST-BY-LED
RESET
AMP-MUTE
N.C
GND
N.C
SCL2
C-SPK MUTE
KEY 1
PROTECT
KEY 2
GND
N.C
STB-5(V)
IR IN
POWER
TIMER-LED
N.C
GND
V-RESET
SCL1
GND
SDA1
S-RESET
PIN NO. ITEM FUNCTION
29
30
31
32
25
26
27
28
21
22
23
24
17
18
19
20
13
14
15
16
9
10
11
12
7
8
5
6
3
4
1
2
KEY SCAN1
PROTECT PORT
KEY SCAN2
GND
N.C
VCC
REMOCON INPUT
POWER ON/OFF RELAY CONTROL
TIMER LED
N.C
GND
VIDEO RESET
SERIAL CLOCK LINE1
GND
SEREAL DATA LINE1
SOUND RESET
STAND-BY LED
RESET
SOUND AMP MUTE
N.C
GND
N.C
SERIAL CLOCK LINE2
CENTER SPEAKER MUTE
SERIAL DATA LINE2
SW3(CONTROL)
GND
SW2(CONTROL)
SUB TUNER AFT CONTROL
GND
MAIN TUNER AFT CONTROL
IIC BUS STOP
4-32
OUT VOLT
3.27[V]
5[mV]
-
2.08[V]
2.57[V]
-
1.04[V]
3.27[V]
2.95[V]
2.47[V]
0.89[mV]
-
-
-
3.27[V]
3.26[V]
2.07[V]
-
-
2.84[mV]
3.43[V]
-
3.49[V]
4.21[V]
2.28[V)
0.83[mV]
2.25[V]
-
-
4.91[V]
3.74[V]
1.03[V]
Samsung Electronics
GND
N.C
N.C
GND
GND
N.C
AN-LINK
N.C
N.C
OSD-TTX-R
GND
OSD-TTX-G
WP
OSD-TTX-B
3.3[V]
OSD-TTX-FB
VS1
N.C
HS1
N.C
GND
N.C
TTX-CVBS
GND
N.C
GND
GND
N.C
5[V]
H-BLANK
GND
V-BLANK
PIN NO. ITEM FUNCTION
61
62
63
64
57
58
59
60
53
54
55
56
49
50
51
52
45
46
47
48
41
42
43
44
37
38
39
40
33
34
35
36
N.C
GND
GND
N.C
5[V]
HORIZONTAL BLANK
GND
VERTICAL BLANK
VERTICAL SYNC
N.C
HORIZONTAL SYNC
N.C
GND
N.C
TTX/CAPTION-CVBS
GND
GND
N.C
N.C
GND
GND
N.C
NOT USE
N.C
N.C
ON SCREEN DISPLAY RED
GND
ON SCREEN DISPLAY GREEN
WRITE PROTECT
ON SCREEN DISPLAY BLUE
3.3[V]
OSD/TTX-FB
Samsung Electronics
Alignment and Adjustments
OUT VOLT
-
168[mV]
-
0.46[V]
-
0.46[V]
3.26[V]
7.31[mV]
-
-
-
-
-
-
-
-
-
-
215.51[mV]
-
-
-
1.19[V]
-
4.96[V]
215.8[mV]
-
-12.10[mV]
-
-
-
-
4-33
Alignment and Adjustments
4-9-3 PROSCAN MODULE Pins
GND
9[V]
N.C
N.C
N.C
N.C
GND
13.5[V]
N.C
COMP
GND
CG-R
CG-G
CG-B
CG-SYNC
D/F
EW
V-BLK
ABL
VD-
VD+
H-BLK
HD
GND
OSD/TTX-FB
OSD/TTX-B
OSD/TTX-G
OSD/TTX-R
V-RESET
GND
SCL1
SDA1
PIN NO. ITEM FUNCTION
29
30
31
32
25
26
27
28
21
22
23
24
17
18
19
20
13
14
15
16
9
10
11
12
7
8
5
6
3
4
1
2
EAST WEST OUT
VERTICAL BLANK
ABL(Automatic Brightness Limiter)
VERTICAL DRIVE(-VOLTAGE)
VERTICAL DRIVE(+VOLTAGE)
HORIZONTAL BLANK
HORIZONTAL DRIVE
GND
OSD/TTX-FB
ON SCREEN DISPLAY BLUE IN
ON SCREEN DISPLAY GREEN IN
ON SCREEN DISPLAY RED IN
VIDEO RESET
GND
SERIAL CLOCK LINE
SERIAL DATA LINE
GND
9[V]
N.C
N.C
N.C
N.C
GND
13.5[V]
N.C
COMP
GND
CONVERGENCE RED
CONVERGENCE GREEN
CONVERGENCE BLUE
CONVERGENCE SYNC
DYNAMIC FOCUS
4-34
OUT VOLT
-
-
-
9[V]
-
-
-
14.05[V]
-
27.28[mV]
-
0.27[mV]
0.27[mV]
0.29[mV]
180.03[mV]
1.5[V]
2.26[V]
-12.07[mV]
2.26[V]
3.46[V]
3.53[V[
215.93[mV]
2.38[V]
-
7.29[mV]
0.46[mV]
0.46[mV]
167.99[mV]
2.94[mV]
-
3.42[V]
3.50[V]
Samsung Electronics
GND
DVD-Pr
DVD-Y
DVD-Pb
GND
5[V]-DW2
N.C
N.C
GND
N.C
N.C
N.C
DVD-Pr/R
DVD-Y/G
DVD-Pb/B
FB
5[V]-DW1
VM-Y
SW3
SW2
N.C
GND
PIP-C
PIP-Y CVBS
GND
MAIN-C
MAIN-Y CVBS
N.C
GND
N.C
GND
RF2-CVBS
PIN NO. ITEM FUNCTION
61
62
63
64
57
58
59
60
53
54
55
56
49
50
51
52
45
46
47
48
41
42
43
44
37
38
39
40
33
34
35
36
GND
DVD-Pr
DVD-Y
DVD-Pb
GND
5[V]-DW2
N.C
N.C
GND
N.C
N.C
N.C
DVD-Pr/R(SCART)
DVD-Y/G(SCART)
DVD-Pb/B(SCART)
FB(SCART)
5[V]-DW1
VM-Y OUTPUT
SW3(CONTROL)
SW2(CONTROL)
N.C
GND
PIP-C INPUT
PIP-Y/CVBS INPUT
GND
MAIN-C INPUT
MAIN-Y/CVBS INPUT
N.C
GND
N.C
GND
RF2-CVBS
Samsung Electronics
Alignment and Adjustments
OUT VOLT
-
4.89[V]
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
1.34[mV]
1.57[mV]
-
4.97[V]
1.97[V]
4.98[mV]
2.08[V]
-
-
1.20[mV]
1.33[mV]
4-35
Alignment and Adjustments
4-9-4 CONVERGENCE MODULE Pins
N.C
-5[V]
5[V]
GND
GND
H-BLK
V-BLK
GND
GV
GH
RV
RH
GND
GND
BV
BH
N.C
IR
N.C
GND
CG-R
CG-G
CG-B
SDA1
5[V]-CG
GND
D/F
GND
SCL1
CG-SYNC
GND
N.C
PIN NO. ITEM FUNCTION
29
30
31
32
25
26
27
28
21
22
23
24
17
18
19
20
13
14
15
16
9
10
11
12
7
8
5
6
3
4
1
2
5[V]-CG
GND
DYNAMIC FOCUS
GND
SERIAL CLOCK LINE1
CONVERGENCE SYNC
GND
N.C
CONVERGENCE RED
CONVERGENCE GREEN
CONVERGENCE BLUE
SERIAL DATA LINE1
N.C
INPUT REMOCON
N.C
GND
GND
GND
BLUE VERTICAL OUT
BLUE HORIZONTAL OUT
GREEN VERTICAL OUT
GREEN HORIZONTAL OUT
RED VERTICAL OUT
RED HORIZONTAL OUT
N.C
-5[V]
5[V]
GND
GND
HORIZONTAL BLANK
VERTICAL BLANK
GND
4-36
OUT VOLT
-
-
34.27[mV]
-107.32[mV]
101.52[mV]
-15.83[mV]
104.32[mV]
-88.95[mV]
-
275[mV]
-13.22[mV]
-
-
-4.99[V]
5.24[V]
-
0.27[mV]
0.26[mV]
0.29[mV]
3.5[V]
-
3.7[V]
-
-
5.2[V]
-
1.5[V]
-
3.4[V]
179[mV]
-
5.2[V]
Samsung Electronics
Electrical Parts List
You can search for the updated part code through ITSELF web site.
URL : http://itself.sec.samsung.co.kr
7. Electrical Parts List
7-1 SP43T8HPX/BOB
Loc. No.
Code No. Description ; Specification Remark
ASSY CPT-R
1 T0026 BP91-00525A ASSY CPT-R;SP43T7HPX/XEF,J54A
..2
BP61-00079A HOLDER-DY;,PJTV,T0.5,NYLON66 V2
..2
T0107 AA91-00735B ASSY-BRKT,CRT;DP,AA91-00722A,PROJ
...3
T0107 AA91-00722A ASSY-BRKT,CRT;,SECC T1.6,PROJ
..2
T0511 AA63-00076B SPACER-LENS;FELT,W7,BLK,T0.8
..2
T0114 AA61-00810B HOLDER-CAP;PROJ,PC,CLR
..2
..2
..2
T0511 AA60-00127B SPACER-LENS;PROJ,SILICONE,D/GRAY
..2
AA61-00809B HOLDER-CRT;PROJ,PC/ABS GF 20%,BLK
AA61-00056B BRACKET-LENS;PROJECTION,SECC,T1.6,-,-,-,
T0333 AA60-00126B SPACER-CAP;PROJ,EPDM,BLK
S.N.A
S.N.A
S.N.A
S.N.A
S.N.A
S.N.A
..2
T0334 AA60-00125B SPACER-CRT;PROJ,SILICONE,D/GRAY
..2
T0245 AA39-00018A LEAD CONNECTOR-ASSY;,UL1015#22,UL/CSA,1P
S.N.A
..2
T0079 AA33-00016A MAGNET CONVERGENCE;JH 92LT - 29F,-,29.1M
..2
T0078 AA27-00278A DEFLECTION YOKE;-,PT-S0712AC,S/S,PJTCRT(
..2
HC015 AA26-30006F FLYBACK;*WIRE*-,FWZ-50A001C,55,30KV
..2
...3
AA61-00845A CASE-COUPLER,R;DP,PROJ,AA61-00806B
AA61-00806B CASE-COUPLER,R;PROJ,ALDC,T8,BLK
..2
AA03-00307A CRT MONO;P16QDU11RJA S,-,-,-,90%,-,FLA
..2
T0051 AA67-10008A LENS;-,-,DELTA,77,RED,S4388,-
S.N.A
S.N.A
S.N.A
..2
T0109 AA67-00147A LENS-ASSY;,DELTA 78,CLEAR A/B
..2
T0081 AA60-10011A SCREW-TAPTITE;-,SWRCH18A,M4,L12,HH,+,PC, S.N.A
ASSY CPT-G
1 T0027 BP91-00526A ASSY CPT-G;SP43T7HPX/XEF,J54A
..2
BP61-00079A HOLDER-DY;,PJTV,T0.5,NYLON66 V2
..2
T0107 AA91-00735B ASSY-BRKT,CRT;DP,AA91-00722A,PROJ
...3
T0107 AA91-00722A ASSY-BRKT,CRT;,SECC T1.6,PROJ
..2
T0511 AA63-00076B SPACER-LENS;FELT,W7,BLK,T0.8
..2
T0114 AA61-00810B HOLDER-CAP;PROJ,PC,CLR
..2
..2
AA61-00809B HOLDER-CRT;PROJ,PC/ABS GF 20%,BLK
AA61-00056B BRACKET-LENS;PROJECTION,SECC,T1.6,-,-,-,
..2
T0511 AA60-00127B SPACER-LENS;PROJ,SILICONE,D/GRAY
S.N.A
S.N.A
S.N.A
S.N.A
S.N.A
..2
T0333 AA60-00126B SPACER-CAP;PROJ,EPDM,BLK
..2
T0334 AA60-00125B SPACER-CRT;PROJ,SILICONE,D/GRAY
..2
T0245 AA39-00018A LEAD CONNECTOR-ASSY;,UL1015#22,UL/CSA,1P
..2
T0078 AA27-00278A DEFLECTION YOKE;-,PT-S0712AC,S/S,PJTCRT(
..2
HC015 AA26-30006F FLYBACK;*WIRE*-,FWZ-50A001C,55,30KV
S.N.A
S.N.A
..2
...3
AA61-00846A CASE COUPLER G;DP,PROJ,AA61-00807B
AA61-00807B CASE-COUPLER,G;PROJ,ALDC,T8,BLK
..2
AA03-00308A CRT MONO;P16QDU11GHA S,-,-,-,90%,-,FLA
..2
T0051 AA67-10071A LENS;DELTA 77 79,-,GREEN,C ELEMENT,
S.N.A
S.N.A
S.N.A
..2
T0109 AA67-00147A LENS-ASSY;,DELTA 78,CLEAR A/B
..2
T0081 AA60-10011A SCREW-TAPTITE;-,SWRCH18A,M4,L12,HH,+,PC, S.N.A
ASSY CPT-B
1 T0028 BP91-00527A ASSY CPT-B;SP43T7HPX/XEF,J54A
..2
BP61-00079A HOLDER-DY;,PJTV,T0.5,NYLON66 V2
..2
T0107 AA91-00735B ASSY-BRKT,CRT;DP,AA91-00722A,PROJ
...3
T0107 AA91-00722A ASSY-BRKT,CRT;,SECC T1.6,PROJ
..2
T0511 AA63-00076B SPACER-LENS;FELT,W7,BLK,T0.8
..2
T0114 AA61-00810B HOLDER-CAP;PROJ,PC,CLR
..2
AA61-00809B HOLDER-CRT;PROJ,PC/ABS GF 20%,BLK
S.N.A
S.N.A
S.N.A
Loc. No.
Code No. Description ; Specification Remark
1
1
1
1
..2
AA61-00056B BRACKET-LENS;PROJECTION,SECC,T1.6,-,-,-,
..2
T0511 AA60-00127B SPACER-LENS;PROJ,SILICONE,D/GRAY
..2
T0333 AA60-00126B SPACER-CAP;PROJ,EPDM,BLK
S.N.A
S.N.A
S.N.A
..2
T0334 AA60-00125B SPACER-CRT;PROJ,SILICONE,D/GRAY
..2
T0245 AA39-00018A LEAD CONNECTOR-ASSY;,UL1015#22,UL/CSA,1P
S.N.A
..2
T0079 AA33-00018A MAGNET CONVERGENCE;JH 92LT - 36F,-,29.1M
..2
T0078 AA27-00278A DEFLECTION YOKE;-,PT-S0712AC,S/S,PJTCRT(
..2
HC015 AA26-30006F FLYBACK;*WIRE*-,FWZ-50A001C,55,30KV
..2
...3
AA61-00847A CASE-COUPLER,B;DP,PROJ,AA61-00808B
AA61-00808B CASE-COUPLER,B;PROJ,ALDC,T8,BLK
..2
AA03-00309A CRT MONO;P16QDU11BEA S,-,-,-,90%,-,FLA
..2
T0051 AA67-10007A LENS;-,-,DELTA,77,CLEAR,S4388,-
S.N.A
S.N.A
S.N.A
..2
T0109 AA67-00147A LENS-ASSY;,DELTA 78,CLEAR A/B
..2
T0081 AA60-10011A SCREW-TAPTITE;-,SWRCH18A,M4,L12,HH,+,PC, S.N.A
T0456 BP91-00407A ASSY MISC-CHASSIS-PACK;SP43T7HPS/XEF,J54
T0100 BP94-00560A ASSY PCB MISC-A/V FRONT;DP,SP43T8HPS/XEC
T0098 BP94-00238A ASSY PCB MISC-VM;DP,HCM4215W3S/XAA,P55A
T0105 BP94-00239A ASSY PCB MISC-DY-JACK;DP,HCM4215W3S/XAA,
ASSY PCB MISC-CRT PCB
1 T0107 BP94-00232A ASSY PCB MISC-CRT PCB;DP,SP42W5HPS/XEU,J
..2
T0103 AA59-00171A MODULE-FOCUS,PACK;SVP-5200,S300-P3,-,-,-
..2
T0077 AA39-20577B LEAD CONNECTOR ASSY;P54A/SVP-55W3HD,UL16
ASSY COVER P-FRONT BOT
1 T0071 BP96-00296E ASSY COVER P-FRONT BOT;43T8,HIPS,HB,GRY,
..2
T0016 BP64-00184C CABINET FRONT-BOTTOM;43T8,HIPS,HB,GRY,SV S.N.A
..2
T0081 6003-001026 SCREW-TAPTITE;RH,+,B,M4,L15,ZPC(BLK) S.N.A
..2
..2
..2
..2
AA61-01132A VELCRO-A;COMMANDO,BST1 1/4H
AA61-20129A HOLDER-WIRE;-,NYLON-66,-,-,-,NTR,DAFC-25
AA61-60003J SPRING-CS;-,SUS304,-,-,OD6,
S.N.A
S.N.A
S.N.A
BP61-00139A GUIDE-KNOB CONTROL;42W4,DP,ABS,HB,G3676 S.N.A
..2
..2
BP64-00078A WINDOW REMOCON-LED;42W4,PC,42W4,PC,CLS.N.A
T0022 BP64-00266A KNOB-CONTROL;DP,BP64-00165A,43T8
..2
T0023 BP64-00166A KNOB POWER;54T8,ABS,HB,GRAY,G3676
S.N.A
..2
T0057 BP64-00177A BADGE-BRAND;AL,T1.5,70,11.3,BLK,SIL S.N.A
..2
T0081 6003-001023 SCREW-TAPTITE;RWH,+,B,M3,L10,ZPC(YEL),SW S.N.A
..2
T0098 BP94-00517W ASSY PCB MISC-CONTROL;DP,SP43T8HPS/XEC,J
..2
AA60-00077A SPACER-DUAL,LOCK;54J8,#250,-,-,-,-,-,-,4 S.N.A
ASSY COVER P-FRONT MASK
1 T0076 BP96-00295F ASSY COVER P-FRONT MASK;43T8,HIPS,HB,G43
..2
T0076 BP96-00295E ASSY COVER P-FRONT MASK;43T8,HIPS,HB,G43
...3
T0017 BP64-00183F CABINET FRONT-MASK;43T8,HIPS,HB,G4309,SV S.N.A
..2
T0254 BP61-00016C BRACKET-SCREEN,TB;DP,43T7,BP61-00109A
..2
T0056 BP61-00017C BRACKET-SCREEN,RL;DP,43T7,BP61-00110A
..2
HC+CW 6009-001296 SCREW-SPECIAL;BH,+,-,M4,L12(11),ZPC(BLK)
..2
T0559 BP61-00043B HOLDER-SENSOR;W9,PC HB,VIOLET S.N.A
Samsung Electronics 7-1
Electrical Parts List
Loc. No.
Code No. Description ; Specification Remark
..2
..2
..2
BP95-00389A ASSY SUB PCB-SENSOR;DP, BP95-00147D,SENS
BP61-00052A HOLDER-WIRE;PJTV,NYLON,66,NATURAL
AA65-00020A CLAMP CORE-WIRE;55W9,NYLON 66
..2
T0077 BP39-00009A LEAD CONNECTOR ASSY;P54A/SVP-42W5,UL2547
..2
T0053 AA67-00115B SCREEN-FRESNEL;43N,-,T2,910*692,-,-,-
..2
T0056 AA67-00195A SCREEN-TINT;43,908*690,T=0.73,P=0.52
S.N.A
S.N.A
..2
T0081 AA60-10011A SCREW-TAPTITE;-,SWRCH18A,M4,L12,HH,+,PC, S.N.A
..2
T0102 BP73-00004A RUBBER-CAP;42W5,SILICONE,WHT,RUBBER
..2
AA63-10002A BAND-TIE;-,NYLON66 V2,-,-,L100,NTR,S.N.A
ASSY COVER P-WOOD
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1 T0324 BP96-00294A ASSY COVER P-WOOD;43T8,WOOD,M/EAST S.N.A
..2
HC+CW AA60-10051A SCREW-WOOD;-,SWRCH18A,M4,L16,PH,+,-,-,ZP S.N.A
..2
HC+CW AA60-10051B SCREW-WOOD;-,SWRCH18A,M3.5,L11,RH,+,-,-, S.N.A
..2
T0156 AA61-00094C HOLDER-RAIL;PCJ533R,ABS,-,-,-,BLK,HB,480 S.N.A
..2
..2
AA61-00097A HOLDER-WIRE;-,NYLON 6/6,-,-,-,NTR,-
..2
T0519 AA61-00533B BRACKET-GRILLE;43,54,62J8,SECC-1 ,T0.5,-
S.N.A
BP61-00075A HOLDER-JERSEY,ASSY;W3,ABS V0,GRAY,63-000 S.N.A
S.N.A
..2
AA61-00616B HOLDER-CRT,MAIN;54J7,DP,-,-,-,-,AA61-005
..2
T0245 AA61-00864A HOLDER-PCB;W3,HIPS,V0,BLK
..2
AA61-01133A VELCRO-B;COMMANDO,BST1 1/4H
..2
T0519 AA61-01213A BRACKET-GRILLE;43T7,SECC,T0.5
..2
T0617 BP64-00185A CABINET-WOOD;43T8,WOOD,,,,,,J54A
S.N.A
S.N.A
S.N.A
S.N.A
S.N.A
..2
..2
AA65-00017A CLAMP CORE-WIRE;ALL MODEL,NYLON6.6,BLK S.N.A
BP61-00019A HOLDER-PALLET;42W5,HIPS HB,BLK S.N.A
..2
T0082 3001-001353 SPEAKER;25W,8OHM,90DB+/-3DB,60HZ+/-12HZ
..2
T0082 3001-001107 SPEAKER;20W,8ohm,95dB,1300Hz
..2
T0245 AA39-00086A LEAD CONNECTOR-ASSY;,2.2UF,REC,REC,200MM
..2
AA98-00049A ASSY-LEAD,CON;-,LEAD-CON,CORE,AA39-20505 S.N.A
...3
T0121 3301-001201 CORE-FERRITE;AE,21x11x32mm,1500,280G
..2
T0115 AA61-00617B BRACKET-CRT,MAIN;DP,54J7,AA61-00475B
..2
S.N.A
6006-001094 SCREW-ASS’Y WOOD;WW,HH,+,M7,L32,ZPC(YE S.N.A
T0092 BP96-00077G ASSY COVER P-TERMINAL,ANT;DP,42W5,HIPS,V
AA96-20130A ASSY-POWER,CORD;-,CP2/NO(4.0R),H/C150,KJ S.N.A
M2893 BP39-00048A LEAD CONNECTOR;P55A/SVP-47W3HRT,UL1617#2
M2893 BP39-00047A LEAD CONNECTOR;P55A/HCM4215W,UL2547#26,U
T0167 AA39-30007A IF-CABLE;-,T,100mm,1365#26
T0168 AA39-00006A CABLE-RCA;-,RCA,3000MM,0.12/10,RED/WHT/Y
AA61-00049B HOLDER-BOX;-,PP,-,-,-,NTR,V0,AA61-20285A
BP61-00300A HOLDER-MIRROR R ASSY;43T8,HIPS,HB,BLK
BP61-00300B HOLDER-MIRROR L ASSY;43T8,HIPS,HB,BLK
T0333 BP64-00017C CABINET BACK/BOTTOM; 43T7,T8
T0334 BP64-00016B CABINET BACK/TOP 43T7,T8
AA40-00050A TUNER;TCLW3101PD18A(S),TCLW3101PD18A(S),
S.N.A
S.N.A
S.N.A
AA40-00051A TUNER;TCPW3001PC18B(S),TCPW3001PC18B(S),
BP61-00012A BRACKET-MIRROR;DP,42W5,AA61-01123A,11.8K S.N.A
T0614 AA65-30013A CLAMP-WIRE;-,NYLON-6 S.N.A
T0614 AA65-30018A CLAMP-WIRE;DONG-A,NYLON-66,-,-,-,DATL-60 S.N.A
T0614 AA65-30104C CLAMP-WIRE;ALL MODEL,NYLON 66,V2,-,NTR, S.N.A
AA65-30008A CLAMP-CORD;-,PE,HB,-,BLK,S.N.A
AA65-30105A CLAMPER CORE-WIRE;ALL MODEL,NYLON 66,V, S.N.A
T0614 AA65-30110A CLAMP-WIRE;ALL MODEL,NYLON 66,V2,-,BLK,P S.N.A
Loc. No.
Code No. Description ; Specification Remark
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
T0081 6003-001019 SCREW-TAPTITE;RH,+,B,M4,L12,ZPC(BLK),SWR
T0081 6003-001022 SCREW-TAPTITE;RH,+,B,M3,L12,ZPC(BLK),SWR S.N.A
T0081 6003-001023 SCREW-TAPTITE;RWH,+,B,M3,L10,ZPC(YEL),SW S.N.A
T0081 6003-001026 SCREW-TAPTITE;RH,+,B,M4,L15,ZPC(BLK) S.N.A
HC+CW 6005-001003 SCREW-WOOD;HH,+,M4,L19,ZPC(BLK),SWRCH18S.N.A
HC+CW 6005-001004 SCREW-WOOD;HH,+,M4,L27,BLK,SWRCH18A S.N.A
T0081 6002-000522 SCREW-TAPPING;TH,+,2,M4,L15,ZPC(BLK),SWR
T0081 AA60-10011A SCREW-TAPTITE;-,SWRCH18A,M4,L12,HH,+,PC, S.N.A
BP64-00044A INLAY-VENT;43T7,PS SHEET,T0.5
S.N.A
AA64-60449B INLAY-COVER;SP-434JMF,PS,T0.5,149.3X69.5
S.N.A
T0108 AA67-00205D MIRROR-BACK;DP,43T7,SSM,795*569*554*(78)
T0616 BP26-00004A TRANS FBT;FUW50A002B,PJCPT,31KV,BK,35KV
T0600 AA60-00072C SPACER-COVER,DUST;43T7,SPONGE 94HF-1,T3. S.N.A
T0069 AA63-60122J SPACER-FELT;SPD-50P3H,FELT,L530,D20,T0.3
S.N.A
T0074 BP59-00008A REMOCON;,TM65A,COMMOANDO,J54A,49,L/GRAY,
T0751 BP68-00066B INSTRUCTION BOOK; PJTV GRIEGO C1.5
S.N.A
AA68-02415A CARD-RTF;COLORIT 54 CREMA,MOJO80G,SPA,A S.N.A
AA63-10007B BAND-PP;W18,CLEA S.N.A
AA63-10002A BAND-TIE;-,NYLON66 V2,-,-,L100,NTR,-
6902-000018 BAG PE; PJTV 42
S.N.A
S.N.A
T0521 AA69-00744L BAG-SHEET;-,HDPE PE FOAM,T0.015,W1650,H1 S.N.A
T0121 3301-001201 CORE-FERRITE;AE,21x11x32mm,1500,280G
M0135 BH73-60304C RUBBER-SUPPORT;DP15LT,CR V0,GRAY,-,14*7* S.N.A
7-2 Samsung Electronics
8. Block Diagram
8-1 Current System
STAND-BY
POWER
MAIN
POWER
K A 7 8 R 0 5
5 . 0 V
E E R 5 3 4 5
8 . 5 V
1 3 7 m A
1 . 3 5 m A
E E R 5 3 4 5
1 1 0 V
E E R 5 3 4 5
1 2 V
E E R 5 3 4 5
1 3 . 5 V
3 8 0 m A
E E R 5 3 4 5
- 2 0 V
E E R 5 3 4 5
+ 2 0 V
E E R 5 3 4 5
+ 2 9 V
1 . 2
1 0 5 m A m A
6 8 0 m A
8 2 5 m A
8 8 m A
M i c o m / E e p r o m 1 3 7 m A
K A 2 7 8 R A 0 5 ( A ) 5 V
K A 2 7 8 R A 0 5 ( A ) 5 V
K A 2 7 8 R A 0 5 ( A ) 5 V
3 0 5 0 5 V
H i g h V o l t
V M 1 1 0 V
T u n e r 3 3 . 0 V
V e r t i c a l D R I V E R
E W , P O R T E C T , H V R E G
C R T
K A 7 8 0 8
K A 2 7 8 R A 0 9
8 . 0 V
9 . 0 V
K A 7 8 R 1 2 1 2 . 0 V
C G A M P
K A 7 9 0 5 ( - 5 . 0 V )
C G A M P
E W
S o u n d A M P
4 4 5 m A
8 0 m A
4 5 5 m A
3 4 0 m A
1 . 0 3 A
1 3 m A
3 m A
1 2 m A
9 0 m A
3 m A
1 4 0 m A
1 0 0 m A
1 4 0 m A
6 5 0 m A
3 0 m A
8 1 5 m A
1 0 m A
8 8 m A
M I C O M , S O U N D
S C A N 1
S C A N 2
C G M D L
F B T
4 4 5
8 0
4 5 5
3 4 0 m A m A m A m A
H E A T E R
V e r t i c a l D R I V E 1 6 . 5 V
V e r t i c a l D R I V E - 1 3 . 5 V
C R T 2 0 0 V
6 2 0 m A
2 1 0 m A
1 9 0 m A
1 7 m A
S O U N D
S C A N M D L
S O U N D
C G - M D L
1 4 0 m A
1 0 0 m A
1 4 0
3 0 m A m A
Samsung Electronics
Block Diagrams
8-1
Block Diagrams
8-2 Power Supply System
INPUT
RECTFIER
RBV-606
Switching IC
STR-F6459
HOT
Line Filter
10mH / 2.45A
1mH / 5A
Stand-by
Trans
PS2561
AC IN
Line Filter
10mH / 2.45A
1mH / 5A
Line Filter
10mH / 2.45A
FUSE
7V / 0.13A
8-2
POWER
TRANS
EER 5345
PC
PS2561
Power
Control
7805
COLD
OUTPUT
RECTFIER
Error AMP
SE11ON
Micom
5V / 0.13A
1 1 0 V / 1 . 2 A
1 3 . 5 V / 0 . 3 8 A
8 . 5 V / 1 . 3 5 A
2 0 V / 0 . 8 2 A
- 2 0 V / - 0 . 6 8 A
2 9 V / 0 . 8 8 A
1 2 V / 0 . 1 1 A
Samsung Electronics
8-3 Deflection System
1 2 V / 0 . 1 1 A
1 1 0 V / 1 . 2 0 A
POWER
Trans
2 0 V / 0 . 8 3 A
- 2 0 V / 0 . 6 8 A
Samsung Electronics
F B T
±13.5V
E / W
C o l l e c t o r
V e r t i c a l
O u t p u t
R - D Y
G - D Y
B - D Y
E / W
A M P
H o r i z a n t a l
O u t p u t
H V
R e g u l a t i o n
P R O T E C T
H - D r i v e
H e a t e r
2 0 0 V
H i g h V o l t a g e
F o c u s V o l t a g e
H D
C R T
D r i v e
( R / G / B )
R - C Y
S T K 3 9 2 - 0 1 0
C o n v e r g e n c e A M P
S T K 3 9 2 - 0 1 0
G - C Y B - C Y
Block Diagrams
8-3
Wiring Diagrams
9. Wiring Diagram
9-1 Connection(Progressive)
A
M
P
S
U
B
CENTER
GND
SURROUND
MUTE
30V
30V
GND
GND
8 P
O
L
C
O
N
T
R
KEY2
GND
GND
KEY- 2
KEY- 1
STD- 5V
GND
KEY- 3
I R
TI MER- LED
STD- LED
SDA1
SCL 1
GND
1 2 P
KEY2
GND
GND
S2- C
GND
S2- I D
S2- Y
GND
AV3- R
GND
GND
AV3- L
AV3- I D
GND
AV4- CVBS
1 2 P
S
I
D
E
A
/
V
C R T
B
SCREEN
GND
210V
N. C
GND
HEATER
GND
12V
B
GND
I K
SPOT
GND
VM-
VM-OUT
C N 5 0 2
1 0 P
9 P
210V
N. C
GND
HEATER
GND
12V
R
GND
I K
SPOT
R
GND
G
GND
B
GND
I K
SPOT. K
D/ F
VM-
VM- OUT
6 P 117V
NC
GND
13. 5V
GND
VM- Y
SCREEN
GND
C R T
G
VM-
VM-OUT
210V
N. C
GND
HEATER
GND
12V
R
GND
I K
SPOT
D/ F
GND
C N 5 0 3
1 1 P
VM-
VM-OUT
3 P X 3
V M
R / G /B
VM-
VM-OUT
SCREEN
GND
210V
N. C
GND
HEATER
GND
12V
R
GND
I K
SPOT
D/ F
GND
SCREEN
C R T
R
6 P
VM-
VM-OUT
D /F
B L O C K
GND
Dy nami c
F oc us
R F oc us
G F oc us
B F oc us
F O C U S
P A C K
D Y - B D Y - G D Y - R
D Y
- M O D U L E
E
A
S
P
K
E
R
Samsung Electronics
KEY- 2
KEY- 1
STD- 5V
GND
KEY- 3
I R
TI MER- L ED
STD- L ED
SDA1
SCL1
GND
C N 9 0 2
1 1 P
L - OUT
GND
R- OUR
GND
C N 6 0 1
4 P
TDA7625
M
E
R
T
U
N
S
E
R
T
U
N
C N Y 0 1
12P
S2- C
GND
S2- I D
S2- Y
GND
AV3- R
GND
GND
AV3- L
AV3- I D
GND
AV4- CVBS
M
I
C
O
M
STD- 5V
GND
I R
M
D
L
S
C
A
N
R
GND
G
GND
B
GND
I K
SPO
D/ F
C N 2 0 1
6 P
117V
NC
GND
13. 5V
GND
VM- Y
C N 8 0 1
15 : C O MP
14 : H - B LK
13 : G ND
12 : V- B LK
11 : 1080i
10 : AB L
9 : VD +
8 : VD -
7 : E W
6 : P R O TE C T
5 : G ND
4 : H D
3 : G ND
2 : STB - 5V
1 : P O WE R
C N 8 0 2
14 : 29V
13 : 29V
12 : 29V- GND
11 : 29V- GND
10 : - 20V
9 : GND
8 : 8.5V
7 : 8.5V
6 : GND
5 : 13.5V
4 : SUB- MUTE
3 : GND
2 : N.C
1 : 125V
GND
5V
UP
GND
5V
RI GHT
GND
5V
L EFT
GND
5V
DOWN
C
G
M
D
L
RH
GND
RV
GH
GND
GV
BH
GND
BV
C N 2 0 2
9 P
MA IN
15 : CO MP
14 : H- BLK
13 : GND
12 : V- BLK
11 : 1080i
10 : ABL
9 : VD+
8 : VD-
7 : EW
6 : PROTEC T
5 : GND
4 : HD
3 : GND
2 : STB- 5V
1 : POWER
1 5 P
14 : 29V
13 : 29V
12 : 29V- G ND
11 : 29V- G ND
10 : - 20V
9 : G ND
8 : 8.5V
7 : 8.5V
6 : G ND
5 : 13.5V
4 : SUB- MUTE
3 : G ND
2 : N.C
1 : 125V
1 4 P
M A S T E R - S W
G ND - R G B ( 3 P )
3 : - 24V
2 : GND
1 : 24V
3 P
P O W E R
S U B
H1/ H2/ V1/ V2
T R A NS
4 P
1 P
SCREEN
210V
N. C
GND
HEAT
GND
12V
C N 5 0 2 A
D e fe lc tio n
F B T
A C - I N P U T
C O N V - A M P
CNZ05
C Y - B
CNZ01
RH
GND
RV
GH
GND
GV
BH
GND
BV
CNZ02
C Y - G
C O N V - A M P
CNZ04
C Y - R
D Y - B D Y - G D Y - R
9-1
10. Schematic Diagrams
10-1 MAIN 1
TP02
TP01
Schematic Diagrams
TP01
TP02
Samsung Electronics 10-1
Schematic Diagrams
10-2 MAIN 2
TP03
TP04
TP05
10-2
TP03
TP04
TP05
Samsung Electronics
10-3 MAIN 3
Samsung Electronics
TP06
TP07
Schematic Diagrams
TP06
TP07
10-3
Schematic Diagrams
10-4 MAIN 4
10-4
TP14 TP13
TP12
TP11
TP10
TP09
TP08
TP15
TP16
TP17
TP18
TP19
TP20
TP20 TP14 TP08
TP15 TP09
TP16 TP10
TP17 TP11
TP18 TP12
TP19 TP13
Samsung Electronics
10-5 MICOM
Samsung Electronics
Schematic Diagrams
10-5
Schematic Diagrams
10-6 CRT
10-6 Samsung Electronics
10-7 SUB 1
TP21
Schematic Diagrams
TP21
Samsung Electronics 10-7
Schematic Diagrams
10-8 SUB 2
TP23
10-8
TP22
TP22
TP23
Samsung Electronics
10-9 SUB 3
Samsung Electronics
Schematic Diagrams
10-9
Schematic Diagrams
10-10 CONVERGENCE ( SDC12 - 1 )
10-10 Samsung Electronics
10-11 CONVERGENCE ( SDC12 - 2 )
Samsung Electronics
Schematic Diagrams
10-11
Schematic Diagrams
10-12 PRO SCAN 1
10-12 Samsung Electronics
10-13 PRO SCAN 2
Samsung Electronics
Schematic Diagrams
10-13
Schematic Diagrams
10-14 AV FRONT
10-14 Samsung Electronics
10-15 VM
Samsung Electronics
Schematic Diagrams
10-15
Schematic Diagrams
10-16 CONTROL
10-16 Samsung Electronics
10-17 DY JACK, SENSOR
DY JACK SENSOR
Schematic Diagrams
Samsung Electronics 10-17
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement