Carrier P474-1100REC Owner`s manual

OWNER'S MANUAL
P474-1100RF
Wireless
Programmable
Digital Thermostat
MODE
FAN
TOTALINE
Wireless Operation
7-Day Programmable
4 Time Periods Per Day
Programmable Fan
Easy To Read Display
Thermoglow Backlight
Auto Changeover
Dual Setpoint
2 Heat, 2 Cool Stages
TOTALINE
Wireless
2000 by Replacement Components Division
Carrier Corporation
2 Stage
Heat & Cool
or
Heat Pump
Table Of Contents
FRONT PANEL
DISPLAY
QUICK START Set the clock and go
BASIC OPERATION
PROGRAMMING 4 Time Periods
ADVANCED SETUP
ABOUT ADVANCED OPERATION
WARRANTY
2
3
5
6
8
12
16
20
CAUTION
Follow P474-1100REC Installation Instructions
before proceeding.
SET THERMOSTAT TO MODE “OFF” PRIOR TO
CHANGING SETTINGS IN SETUP OR RESTORING
FACTORY DEFAULTS.
TOTALINE
P474-1100RF
FCC ID MUH-T10013
This device complies with Part 15 of the FCC rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference,
and (2) this device must accept any interference
received, including interference that may cause
undesired operation.
Important: To assure proper operation use only
AA LITHIUM batteries.
Page 1
Front Panel
1
5
2
3
FAN
TOTALINE
1
Liquid Crystal Display
2
Up/Down Buttons
3
Mode Button
4
Fan Button
5
Transmission Indicator
with Thermoglow
Page 2
4
Display
1
2
1
10
:
12:00
SMTWTFS
7
88
Am ProgramOn Setup
Locked
Pm
88
AUTO
OFFNight
6
Morning Day
Evening
8
Fan On
o
COOL
88
HEAT o
4
1
1
4
3
1
Mode Indicators
Selects the operation mode of the equipment.
HEAT - indicates the heat mode.
COOL - indicates the air conditioning mode.
AUTO - indicates the system will automatically
changeover between heat and cool modes
as the temperature varies.
OFF - indicates the entire system is turned off.
PROGRAM ON - indicates the stored program
is enabled to run. Page 6.
2
Clock with Day of the Week
Indicates the current time and day. This clock is
also used to program the timer periods. Page 5.
3
Room Temperature Display
Indicates the current room temperature.
4
Desired Set Temperature
Indicates desired room temperature(s). Page 7.
Page 3
Display
6
Morning, Day, Evening & Night Indication
Indicates the program time period. Page 8-11.
7
Setup Indication
Indicates the thermostat is in the programming
mode. Page 12.
8
Fan Operation Indication
Fan On - indicates constant, continuous fan
operation.
When Fan On is not lit - indicates the fan will
only operate when necessary to heat or
to cool. Page 7.
10
Locked Indication
Locked appears after the right combination of
buttons are pressed, rendering the buttons
inoperative. Page 17.
Page 4
Quick Start Set the Clock and Go
MODE
FAN
:
12:00
Press the Mode button.
While holding the Mode,
press the Fan button for
2 seconds to enter Setup
screens.
Am
Setup
i
During Setup & Programming:
Pressing the Mode button
selects different flashing items.
(Represented in dark black)
Pressing the Up and Down
buttons will modify the flashing
selection.
Press
Setup
2
To adjust the
clock or Day use
MODE
S
buttons.
Press both Mode and
Fan buttons as
above to return to
normal operation.
MODE
FAN
The Thermostat is preprogrammed from the
factory to operate 1 or 2 Stage equipment* without
the need for further programming. To optimize the
installation of this thermostat follow the instructions
in the Advanced Setup section.
* The thermostat is not preprogrammed from the
factory to operate electric heat or heat pump
systems. To control these systems, follow the
steps in the Wireless Receiver Instructions.
Page 5
Basic Operation
Select Mode
The HEAT setting indicates the
temperature the room has to
reach before the furnace will
turn on to heat the room.
The COOL setting indicates the
temperature the room has to
reach before the air conditioner
will turn on to cool the room.
AUTO will automatically select
heat or cool based on room
temperature demand.
Program On will activate the
stored timer operation.
(Morning, Day, Evening
& Night Periods)
OFF indicates both heating
and air conditioning
systems are turned off.
:
12:00
M
70
70
70
70
70
:
12:00
M
:
12:00
M
AUTO
:
12:00
M
Pm
Pm
Pm
ProgramOn
Pm
Day
:
12:00
M
OFF
Pm
Page 6
69
72
HEAT o
Press
MODE
o
COOL
Press
MODE
72
o
COOL
69
HEAT o
73
Press
MODE
o
COOL
70
HEAT o
Press
MODE
Basic Operation
Select Desired Temperature
:
12:00
M
AUTO
70
Pm
72
o
In any mode, adjust the
desired Set Temperature
with
COOL
69
HEAT o
buttons.
Pressing the up/down buttons in Auto mode will adjust both the heat and cool
set temperatures simultaneously.
Pressing the up/down buttons in Heat or Cool modes will adjust only the
heat or cool set temperature.
Fan
Operation
:
12:00
S
Fan On
65
Pm
Press
FAN
85
o
COOL
55
HEAT o
Fan On indicates constant fan operation.
This feature is active even if the thermostat
is set to Off.
Page 7
Programming
4 Time Periods
(Unit # 1 only)
Time period programming is only available on
Unit Number 1.
MODE
Press the Mode button. While holding the Mode,
press the Up button for 2 seconds to enter
time period programming.
Use the back cover Programming
Worksheet to help with this section.
M
Select the day of week
(M - S)
Press
MODE
Adjust the start time
for Morning.
7M:30
Am
Start
Morning
Press
MODE
Adjust the cooling
setpoint for Morning.
(35 - 99 )
7M:30
Am
74
o
COOL
Morning
Press
MODE
Adjust the heating
setpoint for Morning.
(35 - 99 )
7M:30
Am
Morning
74
o
COOL
72
HEAT o
Continued
Page 8
Press
MODE
Programming
Adjust the start time
for Day.
4 Time Periods
I0M:30
Am
Start
Day
Press
MODE
Adjust the cooling
setpoint for Day.
I0M:30
(35 - 99 )
75
Am
o
COOL
Day
Press
MODE
Adjust the heating
setpoint for Day.
(35 - 99 )
I0M:30
75
Am
o
COOL
73
HEAT o
Day
Press
MODE
Adjust the start time
for Evening.
5M:30
Pm
Start
Evening
Press
MODE
Adjust the cooling
setpoint for Evening.
5M:30
Pm
75
o
COOL
(35 - 99 )
Press
Evening
MODE
Continued
Page 9
Programming
Adjust the heating
setpoint for Evening.
(35 - 99 )
4 Time Periods
5M:30
75
Pm
o
COOL
73
HEAT o
Evening
Press
MODE
Adjust the start time
for Night.
I MI :30
Pm
Start
Night
Press
MODE
Adjust the cooling
setpoint for Night.
I MI :30
Pm
78
o
COOL
Night
(35 - 99 )
Press
MODE
Adjust the heating
setpoint for Night
(35 - 99 )
I MI :30
Am
Night
78
o
COOL
70
HEAT o
Press
MODE
Continued
Page 10
Programming
4 Time Periods
The copy command becomes available after
programming the entire previous day.
Yes
Select Yes or No to copy
the previous day’s
program to this day.
No
:
18:no
T
co
py
If No is selected:
If Yes is selected:
Press
MODE
Selecting Yes, then pressing mode will copy the
previous day’s program and then will ask the
same copy question again. If yes is selected
each time, this routine will repeat.
Press
MODE
If No is selected, as in previous steps, flashing prompts for input will appear for
the 4 time periods for the next day.
Page 11
Advanced Setup
MODE
Press the Mode button and
release.
MODE
THEN IMMEDIATELY press
the Mode button again and
while holding the Mode,
press the Fan button.
When this screen appears
FAN
:
12:00
Am
Setup
I
DO NOT RELEASE THE BUTTONS.
Hold down Mode and Fan for an
additional 7 seconds to enter Setup
screens beyond step #2.
:
12:00
Am
NOTE: Each step # is located at
the top right corner of the
display for easy reference.
Setup
Adjust the time of day
clock.
I
Press
Tip: To change hours quickly, press and
hold the Fan button in and press
the up or down buttons.
MODE
Setup
Select the day of the
week.
M
2
Press
MODE
Leave this setup step
in the OFF mode only.
Off
2o
Setup
On
OFF
3
e
Press
MODE
Continued
Page 12
Advanced Setup
Select the House Code
number. The receiver
must also use this same
number for proper
operation.
Select the Unit ID
number. If more than
1 thermostat is used,
each will need a different
Unit ID number.
Hc
Un
86
Adjust the deadband
from 1 - 6 degrees.
Note: Available only
on Unit ID #1.
Adjust the minimum
difference between
cooling & heating
setpoints.
81f
(0 - 6 )
Select the cycles per
hour limit.
d=cycles per hour
limit defeated.
d1=d + defeat 5 min.
Compressor lockout.
(d, d1, 2 - 6)
o
I
2
2
6
Setup
Press
MODE
Setup
5
Press
MODE
Setup
6
Press
MODE
Setup
7
COOL
HEAT
Press
MODE
Setup
Note: Available only
on Unit ID #1.
4
8
cy
Continued
Page 13
Press
MODE
Advanced Setup
LI
On Setup
On
Select the display backlight always On, or Off
after 8 seconds.
Off
9
Press
MODE
Adjust the programmable
fan timer.
0 - 60 minutes.
0:00 = off
Note: Available only
on Unit ID #1.
:
0:00
Setup
I0
Press
Fan On
MODE
Setup
C
f
Select thermostat
operation in degrees
Fahrenheit or Centigrade.
F
II
Press
MODE
Press the Mode button.
While holding in the Mode, press the Fan
button for 2 seconds to leave the Setup
screens. If no buttons are pressed, the
display will leave the setup screens after
30 seconds.
Page 14
FAN
Advanced Setup
Advanced Setup Table
Step #
1
2
3*
4
5
6**
7
8**
9
10**
11
Description
Range
Time of day clock set
Day of the week
Zoning Use
House Code
Unit Number
Deadband or Temperature swing
Forced minimum difference heat/cool
Cycles per hour
Thermoglow Backlight
Programmable Fan
Fahrenheit or Centigrade
Factory Default
24 hour
Sun - Sat
Off / On
0 - 63
1 - 4/1 - 16
1-6
0-6
d, d1, 2 - 6
Off / On
0:00 - 0:60
F/C
* For proper thermostat operation this setup step should
remain in the OFF position.
** Available on Unit Number 1, only.
Page 15
12:00 Am
Monday
Off
O
1
2
2
6
Off
0:00
F
About Advanced Features & Operation
MEMORY BACKUP - In the event of a power loss, the
thermostat will retain the stored program settings without
external power or batteries.
2 STAGE OPERATION - The 2nd Stage of heat or cool is
turned on when (1) the 1st Stage has been on for a
minimum of two minutes, and (2) the temperature spread
from the setpoint is equal to or greater than: the setpoint
plus the deadband, plus 2 degrees.
Cooling
Heating
2 degrees
2nd Stage
turn on
1st Stage
turn on
Dead
Band
Heat
Setpoint
Dead
Band
Cool
Setpoint
2 degrees
1st Stage
turn on
2nd Stage
turn on
MINIMUM HEAT/COOL SETPOINT DIFFERENCE - The Heat
and Cool setpoints will not be allowed to come any closer
to each other than the value set in Advanced Setup step
# 7, on page 13. This minimum difference is enforced
during Auto changeover and Program On operation.
PROGRAMMABLE FAN - If the Programmable Fan timer is
set to a value other than 0, the fan will run for the
preprogrammed amount of time, page 14, step# 10.
The Programmable Fan timer will start the fan at the top
of each hour. The Programmable Fan may be active
even if the thermostat mode is Off.
Page 16
About Advanced Features & Operation
KEYPAD LOCK - To prevent unauthorized use of the thermostat,
the front panel buttons may be disabled. To disable, or
‘lock’ the keypad, press and hold in the Mode button.
While holding the Mode button in, press the Up and Down
buttons in together. The Locked icon will appear on the
display.
:
12:00
W
Press all 3 for
Keypad Lockout
MODE
ProgramOn
Locked
70
Pm
85
o
COOL
55
HEAT o
To unlock the buttons, again press and hold the Mode
button. While holding the Mode button in, press the Up
and Down buttons in together. The Locked icon will
disappear from the display.
Page 17
About Advanced Features & Operation
DUAL SETPOINT BEHAVIOR - The adjustable setpoint range
is: 35 - 99 degrees in Fahrenheit and 7 - 35 degrees in
Centigrade. When in the modes Heat or Cool, this
adjustable range is unhampered.
When adjusting any Auto mode, including programming
time periods, the thermostat will not allow the Heat
setpoint to get closer to the Cool setpoint than the
value programmed as the minimum difference in
step 7, page 13.
When entering the Auto mode from Cool, the Heat and
Cool setpoints will remain spread apart by the amount
that they were adjusted, prior to entering Auto.
For example: If the Cool setpoint was set to 80 while
in the Cool mode and the Heat setpoint was adjusted to
70 while in the Heat mode, upon entering the Auto mode
the Heat and Cool setpoints would be 80 and 70. Both
setpoints would then move up and down together, (in this
example spread by 10 degrees), by pressing the up or
down buttons.
To move the Heat and Cool setpoints closer together,
enter the Cool or Heat mode by pressing the Mode button,
then adjust the setpoint(s) closer together. Heat is limited
to how close it can come to Cool by step 7, page 13.
Page 18
About Advanced Features & Operation
FACTORY DEFAULTS - If, for any reason it is desirable to
return all stored settings back to the factory default
settings, press the Mode button. While holding the Mode
button in, press the Down button for 2 sec. All icons will
appear. Press and hold in the Fan button until Fd
appears. This resets all factory settings. To return to normal
operation press the Mode button twice.
CALIBRATION - Press the Mode button. While holding the
Mode button in, press the Down button for 2 seconds.
All icons will appear. Press the Mode button once more.
At this point use the Up and Down buttons to calibrate
room temperature, if needed. Press the Mode button to
return to normal operation. NOTE CAUTION ON PAGE 1.
LOW BATTERY WARNING - When the AA Lithium batteries
reach a preset low power state, the display will flash the
Low Battery icon. After this icon appears change the
batteries within a few weeks. Use only AA Lithium
batteries for proper operation.
Battery Eliminator (optional accessory) - Use only the
Totaline accessory (P474-0800) for proper operation.
3vdc, 50ma output, negative center conductor.
Page 19
Warranty
One-Year Warranty - This Product is warranted to be free from defects in material and
workmanship. If it appears within one year from the date of original installation, whether or not
actual use begins on that date, that the product does not meet this warranty, a new or
remanufactured part, at the manufacturer’s sole option, to replace any defective part will be
provided without charge for the part itself; PROVIDED the defective part is returned to the
distributor through a qualified servicing dealer.
THIS WARRANTY DOES NOT INCLUDE LABOR OR OTHER COSTS incurred for diagnosing,
repairing, removing, installing, shipping, servicing or handling of either defective parts or
replacement parts. Such costs may be covered by a separate warranty provided by the installer.
THIS WARRANTY APPLIES ONLY TO PRODUCTS IN THEIR ORIGINAL INSTALLATION
LOCATION AND BECOMES VOID UPON REINSTALLATION.
LIMITATIONS OF WARRANTIES – ALL IMPLIED WARRANTIES (INCLUDING IMPLIED
WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE AND MERCHANTABILITY) ARE
HEREBY LIMITED IN DURATION TOT THE PERIOD FOR WHICH THE LIMITED WARRANTY
IS GIVEN. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED
WARRANTY LASTS, SO THE ABOVE MAY NOT APPLY TO YOU. THE EXPRESSED
WARRANTIES MADE IN THIS WARRANTY ARE EXCLUSIVE AND MANY NOT BE ALTERED,
ENLARGED, OR CHANGED BY ANY DISTRIBUTOR, DEALER, OR OTHER PERSON
WHATSOEVER.
ALL WORK UNDER THE TERMS OF THIS WARRANTY SHALL BE PERFORMED DURING
NORMAL WORKING HOURS. AL REPLACEMENT PARTS, WHETHER NEW OR
REMANUFACTURED, ASSUME AS THEIR WARRANTY PERIOD ONLY THE REMAINING
TIME PERIOD OF THIS WARRANTY.
THE MANUFACTURER WILL NOT BE RESPONSIBLE FOR:
1. Normal maintenance as outlined in the installation and servicing instructions or owners
manual including filter cleaning and/or replacement and lubrication.
2. Damage or repairs required as a consequence of faulty installation, misapplication, abuse,
improper servicing, unauthorized alteration or improper operation.
3. Failure to start due to voltage conditions, blown fuses, open circuit breakers or other
damages due to the inadequacy or interruption of electrical service.
4. Damage as a result of floods, winds, fires, lightning, accidents, corrosive environments or
other conditions beyond the control of the Manufacturer.
5. Parts not supplied or designated by the Manufacturer, or damages resulting from their use.
6. Manufacturer products installed outside the continental U.S.A., Alaska, Hawaii, and
Canada.
7. Electricity or fuel costs or increases in electricity or fuel costs from any reason whatsoever
including additional or unusual use of supplemental electric heat.
8. ANY SPECIAL INDIRECT OR CONSEQUENTIAL PROPERTY OR COMMERCIAL
DAMAGE OF ANY NATURE WHATSOEVER. Some states do not allow the exclusion of
incidental or consequential damages, so the above may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights which may vary
form state to state.
Page 20
Programming Worksheet
see page 8
DAY PERIOD START TIME COOL HEAT
Morning
M
O
N
D
A
Y
T
U
E
S
D
A
Y
W
E
D
N
E
S
D
A
Y
T
H
U
R
S
D
A
Y
F
R
I
D
A
Y
S
A
T
U
R
D
A
Y
S
U
N
D
A
Y
Day
Evening
Night
Morning
Copy Mon
Tue
Day
No
Evening
Yes
Night
Morning
Copy Tue
Wed
Day
No
Evening
Yes
Night
Morning
Copy Wed
Thu
Day
No
Evening
Yes
Night
Morning
Copy Thu
Fri
Day
No
Evening
Yes
Night
Morning
Copy Fri
Sat
Day
No
Evening
Yes
Night
Morning
Copy Sat
Sun
Day
No
Evening
Yes
Night
Printed on recycled paper.
P/N 88-209 Rev. 1
Form: OG-P474-08
Catalog: 53P4-747