Sharp FO-DC550 Service manual

SERVICE MANUAL
CODE : 00ZFODC550A1E
DIGITAL MULTIFUNCTIONAL
SYSTEM
(FO-DC550)
MODEL
FO-DC550
CONTENTS
[ 1 ] GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 1
[ 2 ] SPECIFICATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - 1
[ 3 ] CONSUMABLE PARTS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 1
[ 4 ] EXTERNAL VIEWS AND INTERNAL STRUCTURES . . . . . . . . . 4 - 1
[ 5 ] UNPACKING AND INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . 5 - 1
[ 6 ] COPY PROCESS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 - 1
[ 7 ] OPERATIONAL DESCRIPTIONS . . . . . . . . . . . . . . . . . . . . . . . . . 7 - 1
[ 8 ] DISASSEMBLY AND ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . 8 - 1
[ 9 ] ADJUSTMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 - 1
[10] TEST COMMAND, FAX SOFT SWITCH, TROUBLE CODES . . 10 - 1
[11] MAINTENANCE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 - 1
[12] USER PROGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 - 1
[13] ELECTRICAL SECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 - 1
[14] CIRCUIT DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 - 1
[15] FIRMWARE DOWNLOAD PROCEDURES. . . . . . . . . . . . . . . . . 15 - 1
Parts marked with “ ” are important for maintaining the safety of the machine. Be sure to replace these parts
with the replacement parts specified to maintain the safety and performance of the machine.
SHARP CORPORATION
This document has been published to be used
for after sales service only.
The contents are subject to change without notice.
CAUTION
This product is a class 1 laser product that complies with 21CFR 1040 of the CDRH standard and
IEC825. This means that this machine does not produce hazardous laser radiation. The use of controls,
adjustments or performance of procedures other than those specified herein may result in hazardous
radiation exposure.
This laser radiation is not a danger to the skin, but when an exact focusing of the laser beam is achieved
on the eye’s retina, there is the danger of spot damage to the retina.
The following cautions must be observed to avoid exposure of the laser beam to your eyes at the time of
servicing.
1) When a problem in the laser optical unit has occurred, the whole optical unit must be exchanged as a
unit, not as individual parts.
2) Do not look into the machine with the main switch turned on after removing the developer unit, toner
cartridge, and drum cartridge.
3) Do not look into the laser beam exposure slit of the laser optical unit with the connector connected
when removing and installing the optical system.
4) The middle frame contains the safety interlock switch.
Do not defeat the safety interlock by inserting wedges or other items into the switch slot.
CAUTION
INVISIBLE LASER RADIATION,
WHEN OPEN AND INTERLOCKS DEFEATED.
AVOID EXPOSURE TO BEAM.
VORSICHT
UNSICHTBARE LASERSTRAHLUNG,
WENN ABDECKUNG GEÖFFNET UND
SICHERHEITSVERRIEGELUNG ÜBERBRÜCKT.
NICHT DEM STRAHL AUSSETZEN.
LASER WAVE – LENGTH : 770 – 795nm
Pulse times : 10.24µsec
Out put power : 0.15mW ± 0.01mW
VARO !
AVATTAESSA JA SUOJALUKITUS
OHITETTAESSA OLET ALTTIINA
NÄKYMÄTTÖMÄLLE LASERSÄTEILYLLE ÄLÄ
KATSO SÄTEESEEN.
ADVARSEL
USYNLIG LASERSTRÅLNING VED ÅBNING, NÅR
SIKKERHEDSBRYDERE ER UDE AF
FUNKTION. UNDGÅ UDSAETTELSE FOR
STRÅLNING.
VARNING !
OSYNLIG LASERSTRÅLNING NÄR DENNA DEL
ÄR ÖPPNAD OCH SPÄRREN ÄR URKOPPLAD.
BETRAKTA EJ STRÅLEN. – STRÅLEN ÄR
FARLIG.
At the production line, the output power
of the scanner unit is adjusted to 0.57
MILLI-WATT PLUS 20 PCTS and is
maintained constant by the operation of
the Automatic Power Control (APC).
Even if the APC circuit fails in operation
for some reason, the maximum output
power will only be 15 MILLI-WATT 0.1
MICRO-SEC. Giving and accessible
emission level of 42 MICRO-WATT
which is still-less than the limit of
CLASS-1 laser product.
Caution
This product contains a low power laser
device. To ensure continued safety do not
remove any cover or attempt to gain access
to the inside of the product. Refer all
servicing to qualified personnel.
CONTENTS
[1] GENERAL
1. Major functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
2. Note for servicing and handling. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
[2] SPECIFICATIONS
1.
2.
3.
4.
5.
6.
7.
Basic specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operation specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Copy performance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SPLC printer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Scan function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
RSPF. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Basic specifications (FAX section) . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-1
2-1
2-2
2-3
2-3
2-3
2-4
[3] CONSUMABLE PARTS
1. Supply system table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
2. Environmental . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
3. Production control number (lot No.) identification . . . . . . . . . . . . . . . . 3-2
[4] EXTERNAL VIEWS AND INTERNAL STRUCTURES
1.
2.
3.
4.
5.
6.
7.
Appearance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Internal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operation panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Motors and solenoids . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Sensors and switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PWB unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cross sectional view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-1
4-1
4-2
4-3
4-4
4-5
4-6
[5] UNPACKING AND INSTALLATION
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
Copier installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
Cautions on handling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
Checking packed components and accessories . . . . . . . . . . . . . . . . . 5-1
Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
Removing protective packing materials . . . . . . . . . . . . . . . . . . . . . . . 5-2
Installing the TD cartridge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
Loading the paper tray . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3
Connect the FAX modem PWB line cable . . . . . . . . . . . . . . . . . . . . . 5-3
Power to copier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3
Software for FO-DC550 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3
A. Before installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4
B. Installing the software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4
C. Setting up button manager . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-9
D. Connecting the machine to your computer . . . . . . . . . . . . . . . . . 5-10
11. Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-11
A. USB. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-11
B. Parallel interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-11
12. Moving. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-11
[6] COPY PROCESS
1. Functional diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1
2. Outline of print process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2
3. Actual print process. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2
[7] OPERATIONAL DESCRIPTIONS
1. Outline of operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2. Scanner section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
A. Scanner unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
B. Optical system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
C. Drive system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3. Laser unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
A. Basic structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
B. Laser beam path . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
C. Composition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4. Fuser section. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
A. General description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5. Paper feed section and paper transport section . . . . . . . . . . . . . . . . .
A. Paper transport path and general operations . . . . . . . . . . . . . . . .
6. RSPF section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
A. Outline. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
B. Document transport path and basic composition . . . . . . . . . . . . .
C. Operational descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
D. Cases where a document jam is caused . . . . . . . . . . . . . . . . . . .
E. RSPF open/close detection (book document detection). . . . . . . .
7-1
7-2
7-2
7-2
7-2
7-3
7-3
7-3
7-3
7-3
7-4
7-4
7-4
7-7
7-7
7-7
7-7
7-7
7-7
7. D-D (Duplex to Duplex) mode paper/document transport
(Duplex model) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
A. Initial state . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
B. Front copy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
C. Back copy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8. Shifter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7-8
7-8
7-8
7-8
7-9
[8] DISASSEMBLY AND ASSEMBLY
1. High voltage section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1
A. List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1
B. Disassembly procedure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1
C. Assembly procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1
D. Charger wire cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1
E. Charger wire replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-2
2. Operation panel section. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-2
A. List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-2
B. Disassembly procedure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-2
C. Assembly procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-3
3. Optical section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-3
A. List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-3
B. Disassembly procedure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-3
C. Assembly procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-4
4. Fusing section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-5
A. List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-5
B. Disassembly procedure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-5
C. Assembly procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-7
5. Tray paper feed/transport section . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-7
A. List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-7
B. Disassembly procedure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-7
C. Assembly procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-12
6. Manual paper feed section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-13
A. List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-13
B. Disassembly procedure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-13
C. Assembly procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-14
D. Pressure plate holder attachment . . . . . . . . . . . . . . . . . . . . . . . . 8-14
7. Rear frame section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-15
A. List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-15
B. Disassembly procedure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-15
C. Assembly procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-15
8. Power section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-16
A. List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-16
B. Disassembly procedure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-16
C. Assembly procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-16
9. Duplex motor section (RSPF model only) . . . . . . . . . . . . . . . . . . . . . 8-16
A. List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-16
B. Disassembly procedure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-16
C. Assembly procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-16
10. Reverse roller section (RSPF model only) . . . . . . . . . . . . . . . . . . . . 8-16
A. List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-16
B. Disassembly procedure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-16
C. Assembly procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-16
11. RSPF section (RSPF model only) . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-17
A. RSPF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-17
B. Intermediate tray . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-17
C. Upper cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-17
D. Pickup unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-17
E. Upper cover of the pickup unit. . . . . . . . . . . . . . . . . . . . . . . . . . . 8-18
F. Sensor PWB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-18
G. Pickup solenoid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-18
H. Clutch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-18
I. Manual paper feed roller, pickup roller . . . . . . . . . . . . . . . . . . . . 8-19
J. Transport unit removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-19
K. Belt 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-20
L. Belt 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-20
M. SPF motor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-20
N. Solenoid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-20
O. Clutch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-20
P. Paper supply roller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-21
Q. Paper entry sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-21
R. Transport roller 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-21
S. Paper exit roller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-22
T. Solenoid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-23
[9] ADJUSTMENTS
1. Optical section. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
A. Copy magnification ratio adjustment . . . . . . . . . . . . . . . . . . . . . . .
B. Image position adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2. Copy density adjustment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
A. Copy density adjustment timing . . . . . . . . . . . . . . . . . . . . . . . . . .
B. Note for copy density adjustment . . . . . . . . . . . . . . . . . . . . . . . . .
C. Necessary tool for copy density adjustment . . . . . . . . . . . . . . . . .
D. Features of copy density adjustment . . . . . . . . . . . . . . . . . . . . . .
E. Copy density adjustment procedure . . . . . . . . . . . . . . . . . . . . . . .
3. High voltage adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
A. Main charger (Grid bias) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
B. DV bias check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4. Duplex adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
A. Adjusting the paper reverse position in memory for
duplex copying . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
B. Adjusting trailing edge void in duplex copy mode . . . . . . . . . . . . .
5. SPF (RSPF) scan position automatic adjustment . . . . . . . . . . . . . . . .
6. RSPF (SPF) mode sub scanning direction magnification
ratio adjustment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7. Automatic black level correction . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9-1
9-1
9-2
9-3
9-3
9-3
9-4
9-4
9-4
9-5
9-5
9-5
9-5
9-5
9-6
9-7
9-7
9-8
[10] TEST COMMAND, FAX SOFT SWITCH, TROUBLE CODES
1.
2.
3.
4.
5.
6.
7.
8.
Entering the test command mode . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-1
Key rule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-1
List of test commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-1
Descriptions of various test commands . . . . . . . . . . . . . . . . . . . . . . 10-3
FAX soft switch setting change quick reference table. . . . . . . . . . . 10-38
Soft switch list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-39
Soft switch descriptions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-58
Trouble codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-67
A. Trouble codes list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-67
B. Details of trouble codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-67
9. Communication error codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-70
A. Error code identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-70
[11] MAINTENANCE
1. Maintenance table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-1
2. Maintenance display system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-1
3. Remaining toner indication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-1
[12] USER PROGRAM
1. User programs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
A. Copy mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
B. Print mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
C. FAX mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2. Selecting a setting for a user program . . . . . . . . . . . . . . . . . . . . . . .
12-1
12-1
12-2
12-2
12-4
[13] ELECTRICAL SECTION
1. Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-1
A. Overall block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-1
2. Circuit descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-2
A. Main PWB (MCU) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-2
B. DC power circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-11
[14] CIRCUIT DIAGRAM
1.
2.
3.
4.
5.
6.
MCU PWB. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-1
OPERATION PWB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-26
POWER SUPPLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-29
FAX MAIN PWB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-31
FAX OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-37
ACTUAL WIRING DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-38
[15] FIRMWARE DOWNLOAD PROCEDURES
1.
2.
3.
4.
5.
Initial setting (Serial number setting procedures) . . . . . . . . . . . . . . .
Download procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Version acquisition procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
EEPROM data acquisition procedure . . . . . . . . . . . . . . . . . . . . . . . .
Installing procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
15-1
15-1
15-3
15-4
15-5
[1] GENERAL
1. Major functions
Configurations
Item CPM /
Color
Sharp IEEE
SB/ 2
GDI
PPM
USB
SPF R-SPF Scanner
SPLC E-SORT Duplex Shifter FAX
desk 1284
MB Tray
printer
(push)
Model
LT A4
FO-DC550
16 15 MB Opt
✕
❍
❍
✕
❍
❍
❍
❍
❍
❍
❍
❍
(2.0)
RJ45
External
NIC
✕
Opt
Descriptions of items
CPM:
Copy speed (Copies Per Minute)
SB/MB:
SB = Manual feed single bypass, MB = Manual feed multi bypass
2 tray:
Second cassette unit
SPF:
Original feed unit
R-SPF:
Duplex original feed unit
Color scanner:
Color scanner function
GDI printer:
GDI printer function with USB
SPLC:
SPLC printer function
E-SORT:
Electrical sort
Duplex:
Auto duplex copy function
Shifter:
Job separator function
FAX:
FAX function
Sharpdesk:
Scanner utilities
IEEE1284:
Interface port (parallel)
USB:
Interface port (USB)
RJ45:
Interface port (Network)
External NIC:
AR-NB2N
Descriptions of table
❍: Standard provision
✕: No function or no option available
Opt: Option
(FO-DC550)
2. Note for servicing and handling
When the main unit power is repeatedly turned OFF/ON rapidly (for about 1sec), the IC (OA982) on the MCU PWB may malfunction to cause an error
(E1-00 Communication error), which does not boot the machine. In case of this error, the blank display is kept for several tens seconds and then "E100" is displayed on the panel display.
<Countermeasure>
Turn off the power and keep it for more than 10sec. Then turn on the power.
When the machine is booted.: There is no problem in the MCU PWB.
When the machine is not booted.: The MCU PWB trouble
FO-DC550 GENERAL 1 - 1
[2] SPECIFICATIONS
1. Basic specifications
Item
Type
Copy system
Segment (class)
Copier dimensions
Weight (Approximately)
Desktop
Dry, electrostatic
Digital personal copier
20.4"(W) x 19.8"(D) x 15.0"(H) (518mm(W) x 503mm(D) x 380mm(H))
44.1lbs.(20.0Kg)
TD and drum cartridges included
2. Operation specifications
Section, item
Paper feed Paper feed system
section
AB system
Tray paper feed
section
Multi bypass paper
feed section
Inch system
Tray paper feed
section
Multi bypass paper
feed section
Details
Paper size
Paper weight
Paper feed capacity
Kinds
Remark
Paper size
Paper weight
Paper feed capacity
Kinds
Remark
Paper size
Paper weight
Paper feed capacity
Kinds
Remark
Paper size
Paper weight
Paper feed capacity
Kinds
Paper exit section
Originals
Optical
section
Scanning section
Writing section
Image forming
Remark
Exit way
Capacity of output tray
Original set
Max. original size
Original kinds
Original size detection
Scanning system
CCD sensor
Resolution
Lighting lamp
Type
Voltage
Power consumption
Output data
Writing system
Laser unit
Resolution
Photoconductor
type
Life
Charger
Charging system
Transfer system
Separation system
Developing
Developing system
Cleaning
Cleaning system
1 tray (250 sheets) + multi bypass (50 sheets)
A4, B5, A5
56 - 80g/m2 (15 - 21 lbs.)
250 sheets
Standard paper, specified paper, recycled paper
User adjustment of front paper guide available
A4, B5, A5, B6, A6 (Post card), 16K (Landscape)
52 - 128g/m2 (14 - 34.5 lbs.)
50 sheets
Standard paper, specified paper, recycled paper, envelope,
OHP, Label (Single copy)
User adjustment of side paper guide available
8-1/2" x 14", 8-1/2 x 11", 8-1/2" x 5-1/2" (Landscape)
15 - 21 lbs.
250 sheets
Standard paper, specified paper, recycled paper
User adjustment of front paper guide available
8-1/2" x 14", 8-1/2 x 11", 8-1/2" x 5-1/2", 3-1/2" x 5-1/2"
(Landscape)
14 - 34.5 lbs.
50 sheets
Standard paper, specified paper, recycled paper, OHP, Label,
Envelop (Single copy)
User adjustment of side paper guide available
Face down
200 sheets
Center Registration (left edge)
8-1/2" x 14"
sheet, book
None
3 CCDs (RGB) sensor scanning by lighting white lamp
600 dpi
CCFL
560Vrms
2.8W
R, G, B 1 or 8 bits/pixel / A/D 16bit
Writing to OPC drum by the semiconductor laser
600 dpi
OPC (30ø)
18k
Saw -tooth charging with a grid, / (-) scorotron discharge
(+) DC scorotron system
(-) DC scorotron system
Dry, 2-component magnetic brush development system
Counter blade system (Counter to rotation)
FO-DC550 SPECIFICATIONS 2 - 1
Section, item
Fusing system
Upper heat roller
Lower heat roller
Heater lamp
Fusing section
Electrical section
Power source
Power consumption
Details
type
type
type
Voltage
Power consumption
Voltage
Frequency
Rated current
Max.
Average (during copying)
Average (stand-by)
Pre-heat mode
Auto power shut-off mode
Heat roller system
Teflon roller
Silicon rubber roller
Halogen lamp
120V
800W
120V
60Hz
8A
Less than 1000W
350 Wh/H *1)
86Wh/H *1)
25Wh/H *1)
8.8Wh/H *1)
*1) May fluctuate due to environmental conditions and the input voltage.
3. Copy performance
Section, item
Copy magnification
Manual steps (text, photo)
Copy speed
AB system
A4
(Landscape)
AB system
B5
(Landscape)
Inch system
8-1/2" x 14"
(Landscape)
Inch system
8-1/2" x 11"
(Landscape)
Max. continuous copy quantity
Void
Warm-up time
Power save mode reset time
Paper jam recovery time
Details
Fixed magnification
ratios
4 Reduction + 3 Enlargement
(AB system : 25, 50, 70, 86, 100, 141, 200, 400%)
(Inch system : 25, 50, 64, 78, 100, 129, 200, 400%)
OC: 25 - 400%, SPF/RSPF: 50 - 200%
Zooming
magnification ratios
(376 steps in 1% increments)
5 steps
First copy time
Tray paper feed 9.6 sec. (Pre-heat mode: 25 sec. / Auto power-shut-off mode: 40 sec.)
A4 or Letter/100%/Auto Exposure
Copy speed (CPM) Same size
15
Enlargement
15
Reduction
15
Copy speed (CPM) Same size
15
Enlargement
15
Reduction
15
Copy speed (CPM) Same size
12
Enlargement
12
Reduction
12
Copy speed (CPM) Same size
16
Enlargement
16
Reduction
16
99
Void area
leading edge
1 - 4mm
Trailing edge
4mm or less, 6mm or less (Duplex copying/both image)
Side void area 0.5mm or more (per side)
4.5mm or less (total of both sides)
Image loss
leading edge
Same size: 3.0mm or less (OC) / 4.0mm or less (SPF/R-SPF/Duplex)
Enlarge: 1.5mm or less (OC) / 3.0mm or less (SPF/R-SPF/Duplex)
Reduction (50%): 6.0mm or less (OC) / 8.0mm or less (SPF/R-SPF/Duplex)
0 sec.
0 sec.
0 sec.
FO-DC550 SPECIFICATIONS 2 - 2
4. SPLC printer
Print speed
First print time
Duplex
ROPM
CPU
Memory
Interface
Network
Emulation
MIB support
Resolution
Supported OS
WHQL support
Application
Max. 15ppm (A4 / with ROPM) / 16ppm (Letter / with ROPM)
9.6 sec. (without data transfer time)
Yes
Yes
None
Share the memory with E-SORT function
IEEE1284 / USB 2.0
External NIC (Option: AR-NB2N)
SPLC (JBIG GDI), Option: PCL/PS (Option) (AR-NB2N)
Yes (with AR-NB2N)
600dpi *1
Win 95 / 98 / Me / NT 4.0 / 2000 / XP
Yes *2
Status window
*1: Engine Resolution
*2: Running change
5. Scan function
Type
Scanning system
Light source
Resolution
Originals
Output data
Scan range
Scan speed
Protocol
Support file format
Interface
Scanner utility
Scan key/lamp
Duplex scan
Supported OS
Void area
WHQL supported
Flat Bed Color Scanner
Document glass / RSPF
3 CCDs (RGB) sensor scanning by lighting white lamp (2 pcs of CCFL)
Optical: 600 x 1200dpi
Setting range: 50 - 9600dpi (Preview resolution is fixed at 75dpi)
Sheet type / Book type
R, G, B 1 or 8 bits/pixel / A/D 16bit
OC / RSPF: 8.5" (297mm) (L) x 14" (431mm) (W)
Original position: Platen: Left center / SPF: Right center
OC / RSPF: Max. 2.88ms/line (Color/Gray scale), Max. 0.96 ms/line (B & W)
TWAIN / WIA (Only XP) / STI
RAW
USB2.0
Button Manager / Sharpdesk
Yes
Yes *1
Win 98 / Me / 2000 / XP
No (User settable by PC)
Yes *2
*1: Sharpdesk only
*2: Running change
6. RSPF
Original capacity
Original size
Original replacement speed
Job speed (Tray1,Landscape)
Single copy
Multi copy
Original placement
Original weight
Mixed feeding
Original which cannot
30 sheets (52 to 90g/m2) (14 to 23.9 lbs.)
A4 to A5 / 8-1/2" x 14" to 5-1/2" x 8-1/2"
12CPM (A4/8-1/2" x 11"Landscape)
S to S
12CPM
S to D
5.6CPM
D to S
5.5CPM
D to D
5.2CPM
S to S
16CPM
D to S
16CPM
Face up
52 to 90g/m2(14 - 23.9lbs.)
No
Thermal papers, originals with punch holes for files, be used folded paper, transparent originals
such as OHP films, stapled or clip used originals with cover up liquid used, Originals with tape
sealed, originals with high level frictional coefficient such as photos or catalogs.
FO-DC550 SPECIFICATIONS 2 - 3
7. Basic specifications (FAX section)
Large item
Communication
system
Middle item
Electronic
transmission system
Small item
Electronic
transmission time
Compression/
Extraction system
MODEM speed
Mutual communication
Used line
Sub item
Used line number
Connection form
Transmission
functions
Transmission
operation
ECM
Items which can be
selected and
registered by user
when transmitting
Auto send function
Application send
function
Chain dial
Rapid key dial
Speed dial
Group dial
Address book send
Registration key
Number of items
Number of digits of
destination number
Destination
registration name
Retrieval characters
Communication start
speed
International
communication mode
Transmission method
Number of items
Number of digit of
destination number
Destination
registration name
Retrieval characters
Communication start
speed
International
communication mode
Transmission method
Registration key
Number of groups
which can be
registered
Destination
registration name
Number of stations
which can be
registered in one
group
Numbers which can be
registered
Retrieval characters
Transmission method
Retrieval target
Retrieval key
Retrieval character
FO-DC550 SPECIFICATIONS 2 - 4
Specifications
Less than 3 sec (Super G3 mode, 33600bps)
Less than 7 sec (G3 ECM mode, 14400bps)
MH, MR, MMR, JBIG
33600bps - 2400bps (Automatic fall-back)
Super G3/G3
Public switched telephone network (PSTN), Private
branch exchange (PBX)
1 line
For 1 line of telephone;
• FAX machine
• External telephone
Yes
• Specifying the destination number
• Resolution
• Density
• Transmission start time
• Polling receive
• Cover addition setting
• Send document scan system
Auto send function to a predetermined telephone
number
Max. 50 digits
One-touch key
Max. 18 items
Max. 40 digits
Max. 20 characters
0 - 3 characters
Max. speed: 33600bps/ High speed: 14400bps/
Middle speed: 9600bps/ Low speed: 4800bps
NO/ Mode 1/ Mode 2/ Mode 3
One-touch dial key
100 items (Reduction number 00 - 99)
40 digits
20 characters
0 - 3 characters
Max. speed: 33600bps/ High speed: 14400bps/
Meddle speed: 9600bps/ Low speed: 4800bps
NO/ Mode 1/ Mode 2/ Mode 3
Speed dial key + (00 - 99) + Start key
One-touch dial key
18 items (One-touch dial + Group dial)
20 characters
Max. 100 stations in one group (Max. total items
which can be registered: 150 items)
Destination numbers registered in one-touch dial and
speed dial, 10-key dial
0 - 3 characters
Group dial key
• Speed dial
• One-touch dial
• Group dial
SEARCH key
0 - 3 characters
Large item
Send functions
Middle item
Document scan
function
Small item
Document size
Sub item
Max. document width
Max. document length
Send document size
Half-tone reproduction
Scan density select
function
Scan resolution select
function
Document size
specification
Half-tone
Resolution selection
Density select
Selectable image
quality mode
Resolution select
Document table scan
(OC send) function
Send document
information adding
function
Sender registration/
send function
Send header function
Page counter function
Cover adding function
Basic send functions
Send message adding
function
Index function
Direct send function
Memory send function
Sender telephone
number
Sender registration
name
Header display
content
Adding position
Adding form
Display items
Fixed message
Send form
Number of items of
send reservation
Operation when
memory full
Quick online send
function
Auto resend function
When busy tone
detected
When no response
(CED/ FSK signal are
not detected)
Communication error
Long document send
function
FO-DC550 SPECIFICATIONS 2 - 5
Specifications
Inch series: 8.5"
AB series: 210mm
500mm (Only form RSPF, with user support)
AB series: A4
Inch series: Letter (8.5 x 11)/Legal (8.5 x 14) (Default:
Letter (8.5 x 11))
Yes
256 gradations
Manual 5 steps
Standard/Fine/Super Fine/Fine + Half-tone/Super
Fine + Half-tone (Default: Standard)
Light/Medium/Dark
Scan density
Standard: 8dot x 3.85 line/mm
Fine: 8dot x 7.7 line/mm
Super Fine: 8dot x 15.4 line/mm
Half-tone: Scan in 256 gradations
Book document scan/send function from the
document table (OC). In one send job, the send
document size is fixed.
20 digits
40 characters
Sender number registered in sender registration/
Sender name/ Send date and time/ page
Top right (The right edge)
P. XXX (Max. 999)
• Date and time
• Destination name (Max. 20 characters)
• Destination number (Max. 40 digits)
• Sender name (Max. 20 characters)
• Sender number (Max. 20 digits)
• Send quantity (3 digits)
• Send message (When send message adding
function is used)
NO MESSAGE/CONFIDENTIAL/PLS. DISTRIBUTE/
URGENT/PLS. CALL BACK/IMPORTANT
Yes (Max. 10 kinds in printable area)
Yes
• Send reservation
• Time specifying send
• Group send
• Serial broadcast
Max. 52 items (excluding redial)
Group send and broadcast are treated as one item.
• Document scan stop
• Memory full display → Job continuation check
• Job continuation: Scanned document data are
sent.
• Job stop: Scanned document data are deleted.
• In either case, document is held in SPF and not
discharged.
Valid when memory mode is ON. Scan of send
document data and send are performed together.
Redial is performed according to the setting of
"Number/interval of redial when busy."
Redial is performed according to the setting of
"Number/ interval of resend in communication error."
Supports up to 500mm. When this length is
exceeded, "PAPER JAM" occurs.
Large item
Send functions
Middle item
Application send
function
Small item
Manual send function
Time specifying send
function
Sub item
Available
communication
Number of set items
Set range
Day of week
Group send function
Serial broadcast
function
Duplex send function
Broadcast send
destination
Send document size
Incoming
functions
system
Incoming detection
function
Application incoming
function
Call signal detection
function
Remote select
function by CNG
detection
Distinctive Ring
function
Receive
functions
system
Receive function
Receive standby
mode
Basic receive function
Auto receive function
Volume select
Volume select
OFF/LOW/MIDDLE/HIGH
Follows setting on the main unit.
Number of
registrations
Number of calls
Tel/FAX auto select
Incoming reject
conditions
Manual receive
function
Basic receive function
Valid only in duplex support models.
Direct send and scan from OC cannot be made.
A4/ Letter/ Legal size
Call bell is distinguished from net call signals to judge
incoming.
Receive is started when CNG signal is detected in
standby with external telephone used.
Conforms to the call distinguishing function provided
by the local telephone company.
OFF/STANDARD/Pattern 1 - 5
Incoming is rejected when remaining memory
capacity is less than 7%.
OFF/LOW/MIDDLE/HIGH
Call bell pattern
Incoming reject
function
Call sound volume
adjustment function
Alarm sound volume
adjustment function
Key sound volume
setting
Junk FAX protection
function
Specifications
This function allows to switch to FAX manually when
off-hook with document set.
Memory send, Polling, serial broadcast, serial send
request
Max. 5 items
00:00 - 23:59 (Unit: 1 min)
8 kinds (From Monday to Sunday, and no
specification)
A message is sent sequentially to two or more
destinations registered in group dial. (Max. 52
destinations can be registered in one group.)
Max. 100 items
Number of calls
Memory receive
function
Substitution receive
function
Forcible memory
receive function
Overtake output
function
Print hold
FO-DC550 SPECIFICATIONS 2 - 6
Junk stations are registered to be rejected.
Max. 10 items
• Auto (AUTO)
• Manual (MAN.)
• Answering machine (A.M.)
The line is switched to FAX by detection of call signal.
(receive standby mode)
AUTO: 0 - 9 times (Default: 2 times)
No
• During Test Command by serviceman
• Insufficient memory capacity
• During menu
• During memory status display
Receive is manually started.
0 - 9 times (Default: 0 times)
Receive data are accumulated in memory, and
outputted when output conditions are satisfied.
Countermeasure against print inhibit state.
• No recording paper
• Recording paper jam
• During copy/print job
• During printing by printer
• Cover open
• Paper empty, size error
No
No
Yes
Large item
Receive
functions
system
Middle item
Receive document
output function
Small item
Auto reduction/
divided receive
function
Sub item
Auto reduction
function
Divided receive
function
Polling receive
function (Send request
function)
Sequential send
request (Polling)
communication
Remote send
Protection function
Print system
Recording paper
Recordable size
Recording paper
setting
Paper feed
Recording paper size
detection
Recording paper
empty detection
Duplex receive
Telephone
functions
system
Record table
system
Transfer function
Main unit telephone
function
On-hook dial function
Manual redial function
External telephone
connection function
Report list
Pause function
Pulse/Tone select
function
Select function by
DTMF
Report output function
Recording table auto
print function
Communication report
list
Max. memory digit
Display digits
Specifications
When the reference line number is in the specified
range.
When the reference line number exceeds the
specified range.
The remote machine must be provided with polling
function. Communication is allowed with an other
company machine.
Polling is made to two or more specified destinations.
Number of items of destination registration: Max. 100
items
Scanned document data in memory are sent
automatically by send request from the remote
machine.
• Check by sender number
• Check by allow number
A4/8.5 x 11/8.5 x 14
AUTO/TRAY 1/TRAY 2 (When the option installed)
(In AUTO, TRAY1 has priority.) (Default: AUTO)
Paper feed by tray (Excluding multi manual feed)
The recording paper length is detected. If the size
differs, a paper size error occurs.
Detected by a paper pickup error.
Available only in the duplex function support models.
No
Yes
50 digits
End 20 digits
Yes (Fixed to 2sec)
Yes
Select number (1 digit) + [**] (0 - 9)
Report select
Number of items
Report select
Print status select
FO-DC550 SPECIFICATIONS 2 - 7
• TIMER LIST
• ACTIVITY REPORT
• TELEPHONE# LIST
• GROUP LIST
• PASSCODE LIST
• JUNK FAX# LIST
• USER PROGRAM LIST
Auto print for every 50 items of send/receive total.
•
•
•
•
•
•
•
Send report list
Receive report list
Serial broadcast send report list
Image memory addition
ALWAYS PRINTS
ERROR ONLY
NEVER PRINTS
Large item
Memory
functions
system
Middle item
Memory outline
Small item
Memory capacity
Data storage area/
backup when service
interruption (Recorded
data, receive data)
Treatment when
memory full
Quick online
Memory send
Service
functions
system
Others
Memory status check
function
Memory content check
function
Document jam
Test command
function
Counter function
Environmental
functions
Sub item
Standard memory
Option
Document quantity to
be stored
Image data
Data other than image
Memory full on the first
page
Memory full on the
second or later page
Memory full on the first
page
Memory full on the
second or later page
Communication
counter
Auto clear
Auto shut -off
Date and time setting
function
Image priority function
BEEP LENGTH
(Communication end
sound length) setting
Auto summer time
setting
Specifications
2MB
No
A4 standard documents 120 pages
Flash memory (Data are retained when the power is
turned off or when the battery is exhausted.)
SRAM (Data are retained when the power is turned
off, but deleted when the battery is exhausted with the
power OFF.)
Send cancel without call-out
The line is shut-off after sending the last page of
scanned data.
Send cancel
Send/Cancel is selected depending on the select
menu display.
Send: The line is shut off after sending the scanned
data.
Cancel: Cancel even scanned data.
Yes (The remaining memory capacity (%) is
displayed on the LCD.)
Not-sent job is displayed on the LCD. (Cancel is
possible.)
Error LED, LCD message are displayed.
Send/receive of specified signals, commands, and
image data are performed without a remote machine.
• Number of send pages
• Number of receive pages
• Number of output pages
• Send time
• Receive time
Conforms to the main unit setting. When the
operation is left for 1 min or more, the display returns
to the main menu.
Conforms to the main unit setting.
Month/ Day/ Year/ Day of week/ O'clock/ minute
STANDARD/FINE/SUPER FINE
3SEC/1SEC/NO BEEP
First Sunday of April AM2:00 → 3:00,
Last Sunday of October AM2:00 → 1:00
(Default: OFF)
Conforms to the main unit setting.
Multi language
function
FO-DC550 SPECIFICATIONS 2 - 8
[3] CONSUMABLE PARTS
1. Supply system table
No.
Name
1 TD Cartridge (Black)
2
Content
Toner/Developer CA with IC Chip x 1
(Toner; Net Weight 196g) (Developer; Net Weight 180g)
Polyethylene Bag (UBAGF0005YSZZ) x 1
Drum Cartridge
Drum Cartridge
Life
6K
(5% document)
Product name
FO-55ND
18K
FO-55DR
Package
5
5
2. Environmental
The environmental conditions for assuring the copy quality and the machine operations are as follows:
(1) Normal operating condition
(4) Supply storage condition
Temperature:20 - 25°C
Humidity:65 ± 5%RH
Humidity (RH)
90%
(2) Acceptable operating condition
Humidity (RH)
85%
60%
20%
–5˚C
20%
10˚C
30˚C
35˚C
30˚C
40˚C
(3) Transport condition
Humidity (RH)
90%
60%
15%
–25˚C
FO-DC550 CONSUMABLE PARTS 3 - 1
45˚C
3. Production control number (lot No.) identification
<Developing cartridge>
Production month
Production day
Destination code
(Dealer, distributor, OEM, etc.)
Production place
(SOCC: Fixed to B.)
End digit of year
Version No.
*
Destination
Division
EX Destination
Option Destination
A same pack
B same pack
A
B
Production control
label attachment position
No.
G
H
P
Q
<Drum cartridge>
The label on the drum cartridge shows the date of production.
(SOCC production)
Production month
Production day
Destination code
(Dealer, distributor, OEM, etc.)
Production place
Production control
label attachment position(*1)
(SOCC: Fixed to B.)
End digit of year
Version No.
*1 The production control label is not attached to the cartridge of a
China product.
<JAPAN production>
Ver.A
9
1
1
0001
X
Production month
(1 - 9 = Jan. - Sep. 0 = Oct. X = Nov. Y = Dec.)
Serial number of month
Fixed to 1.
Pack division
(See table below)
End digit of year
Version No.
Division
Ex production
Option
Same pack
No.
1
2
3
FO-DC550 CONSUMABLE PARTS 3 - 2
[4] EXTERNAL VIEWS AND INTERNAL STRUCTURES
1. Appearance
RSPF
10
11
12
Interface
20
14
13
21
1
2
3
6
7
8
4
5
15
16
18
17
18
19
L
TE
9
22
23
E
LIN
1
4
7
10
13
16
19
22
Document glass
Front cover
Side cover open button
Reversing tray
Document feeder tray
Paper output tray extension
Power cord
Telephone line port
2
5
8
11
14
17
20
23
FAX operation panel
Paper tray
Bypass tray paper guides
Original guides
Exit area
Power switch
USB port
External telephone line port
3
6
9
12
15
18
21
24
Operation panel
Side cover
Bypass tray
Document feeder cover
Paper output tray
Handles
Parallel port
Paper holding arm
2. Internal
TD cartridge
Drum cartridge
1
2
3
4
5
1
4
Side cover
Charger cleaner
2
5
Fusing unit release lever
Front cover
3
Transfer charger
FO-DC550 EXTERNAL VIEWS AND INTERNAL STRUCTURES 4 - 1
24
3. Operation panel
22
23
24
25
26
27
01
10
02
11
03
12
04
13
05
14
SPEED/ BROAD- RECEPTION REDIAL/
MEMORY SEARCH CAST
MODE
PAUSE
06
15
07
16
08
17
09
18
SHIFT
COVER
RESOLUTION
CONTRAST SHEET
29 30 31
2
3
4
5
FO-DC550
LIST
LINE/FAX DATA
28
1
2-SIDED TX
SPEAKER
32
Display
READY TO COPY.
100% 8.5x11
18
1
3
19
33
34 35
6 7
8 9 10 11
12 13 14
15
16 17
0
20
21
[MODE SELECT] key / Mode indicators
Press this key to select the mode. The indicator of the selected
mode lights (copy, printer, scanner, fax mode indicators).
2
Display
This shows messages indicating the machine status and any
problems that occur, as well as user programs and function setting
menus.
[CLEAR] key (
)
Use this to clear the set number of copies, as well as cancel a job
that is in progress. When a setting menu appears, use this key to
move back to the previous menu level.
RSPF indicator
This lights up when an original is placed in the RSPF.
[TRAY SELECT] key (
)
Use to select the paper tray that has the desired paper for copying.
Numeric keys
4
Use these to enter the number of copies and other numerical
settings.
The keys can also be used to select items in function setting menus.
5 Power save indicator
6
This lights up when the power save function is activated.
7 Error indicator
8
This lights steadily or blinks when a paper misfeed or other error
occurs.
9 Tray location indicator
10 [MENU] key
Indicates the selected paper tray. The indicator blinks when the tray
Press this key to select the paper size for copying, to configure a
is out of paper during operation or is not closed properly.
user program or to display the total count.
11 [2-SIDED COPY] key
12 [E-SORT/SP.FUN] key
Press to select the automatic two-sided copying mode.
Press to select the sort function, 2 IN 1 copy function, or margin shift
function.
13 [
] key (
), [
] key (
), [ENTER] key
14 [EXPOSURE] key
Press the [
] key (
) or [
] key (
) to select an item in a
Use to switch from auto exposure adjustment to text mode or photo
function setting menu.
mode.
Press the [ENTER] key to enter a selection.
16 [START] key (
) / Ready indicator
15 [COPY RATIO] key
The ready indicator lights up when copying or scanning is possible.
Press to select an enlargement or reduction ratio.
To begin copying, press the [START] key (
).
To select a preset ratio setting, press the [COPY RATIO] key and
The [START] key (
) is also pressed to return to normal operation
select the desired preset ratio. To select a ratio that is not preset,
from auto power shut-off mode.
press the [COPY RATIO] key, select the preset ratio that is closest to
the desired ratio, and then press the [
] key (
) or [
] key
(
) to increase or decrease the ratio in increments of 1%.
17 [CLEAR ALL] key (
)
18 Shows the current copy ratio.
This returns all functions to the default settings. When pressed in a
setting menu, this returns the settings and display to the initial state.
19 Shows the selected paper size.
20 Shows the number of copies that has been entered with the numeric
keys.
21 A checkmark " " appears when the exposure has been changed,
22 Rapid keys
or when two-sided copying, sort, 2 IN 1, or margin shift is selected.
Press one of these keys to dial a fax or telephone number
automatically.
23 [MEMORY] key / indicator
24 [SPEED/SEARCH] key
Used for sending faxes in memory (indicator is lit) or direct sending
Press this key to dial a two digit Speed Dial number.
(indicator is not lit).
During character inputting, use this key to delete an incorrect entry.
Also, press this key twice to search for an automatic dialing number.
25 [BROADCAST] key
26 [RECEPTION MODE] key
Press this key to send originals to a group of receiving fax machines.
Press this key to select the mode of reception.
27 [REDIAL/PAUSE] key
28 [SHIFT] key / indicator
Press this key to automatically redial the last number you dialed.
Press this key to switch between upper and lower case.
Also, press this key to insert a pause when entering numbers.
29 [RESOLUTION] key
30 [CONTRAST] key
Press this key to adjust the resolution before sending faxes.
Press this key to adjust the contrast before sending faxes.
31 [COVERSHEET] key
32 LINE/FAX DATA indicator
Press this key to automatically add a cover sheet and message to a
Lit when sending/receiving faxes, blinking when receiving data.
fax.
33 [LIST] key
34 [SPEAKER] key
Press this key to select from a list of available reports.
Press this key to begin manual dialing. (To close the line, press the
[SPEAKER] key again.)
35 [2-SIDED TX] key
Press this key to fax a two-sided original.
FO-DC550 EXTERNAL VIEWS AND INTERNAL STRUCTURES 4 - 2
4. Motors and solenoids
9
12
2
8
11
10
4
1
5
13
6
3
No.
1
2
3
4
5
6
7
8
9
10
11
12
13
Part name
Main motor
Scanner motor
Toner motor
Cooling fan motor
Resist roller solenoid
Paper feed solenoid
Multi paper feed solenoid
SPF motor
Duplex motor
Original feed solenoid
SPF paper feed solenoid
SPF gate solenoid
Shifter motor
Control signal
MM
MRMT
TM
VFM
RRS
CPFS1
MPFS
SPFM
DMT
SPUS
SPFS
SGS
SFTM
Function / Operation
Drives the copier.
Drives the optical mirror base (scanner unit).
Supplies toner.
Cools the optical section.
Resist roller rotation control solenoid
Cassette Paper feed solenoid 1
Multi manual pages feed solenoid
Drives the single pass feeder
Devices the duplex paper transport section
Original pick up solenoid
Original feed solenoid
Controls the document reverse gate.
Drives the shifter.
FO-DC550 EXTERNAL VIEWS AND INTERNAL STRUCTURES 4 - 3
7
5. Sensors and switches
1
2
8
9
3
4
10
5
7
6
No.
Name
1 Scanner unit home position
sensor
2 POD sensor
3 PPD2 sensor
4 Cassette detection switch
5 PPD1 sensor
6 Door switch
Signal
MHPS
Type
Transmission sensor
Function
Scanner unit home position detection
Output
"H" at home position
POD
PPD2
CED1
PPD1
DSW
Transmission sensor
Transmission sensor
Micro-switch
Transmission sensor
Micro-switch
Paper exit detection
Paper transport detection 2
Cassette installation detection
Paper transport detection 1
Door open/close detection
(safety switch for 24V)
New drum detection switch
"H" at paper pass
"L" at paper pass
"H" at cassette insertion
"L" at paper pass
1 or 0V of 24V at door open
7
Drum reset switch
DRST
Micro-switch
8
SPF sensor
Transmission sensor
9
10
SPPD sensor
PD1 sensor
SPID/
SD SW
SPPD
PD1
Transmission sensor
Micro-switch
Paper entry detection
Cover open/close detection
Paper transport detection
Paper width detect
FO-DC550 EXTERNAL VIEWS AND INTERNAL STRUCTURES 4 - 4
Instantaneously "H" at insertion of
new drum
"L" at paper pass
"L" at paper pass
"H" at B4 size or less
"L" at B4 size or more
6. PWB unit
5
2
1
10
8
6
9
4
7
3
No.
1
2
3
4
5
6
7
8
9
10
Name
Exposure lamp inverter PWB
Main PWB (MCU)
Operation PWB
Power PWB
CCD sensor PWB
LSU motor PWB
TCS PWB
LSU PWB
FAX-operation PWB
Modem PWB
Function
Exposure lamp (CCFL) control
Copier control
Operation input/display
AC power input, DC voltage control, High voltage control
For image scanning
For polygon motor drive (In the LSU)
For toner sensor control
For laser control (In the LSU)
FAX operation input
FAX control
FO-DC550 EXTERNAL VIEWS AND INTERNAL STRUCTURES 4 - 5
7. Cross sectional view
3
1
2
5
18
15
16
17
4
6
7
8
9
10
14
No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
Part name
Scanner unit
Exposure lamp
LSU (Laser unit)
Paper exit roller
Main charger
Heat roller
Pressure roller
Drum
Transfer unit
Pickup roller
Manual paper feed tray
Manual paper feed roller
PS roller unit
Paper feed roller
Pickup roller
Separation roller
PS roller
Paper exit roller
13
12
11
Function and operation
Illuminates the original with the copy lamp and passes the reflected light to the lens unit(CCD).
Exposure lamp (CCFL) Illuminates original
Converts the original image signal into laser beams and writes onto the drum.
Roller for paper exit
Provides negative charges evenly to the drum surface.
Fuses toner on the paper. (Teflon roller)
Fuses toner on the paper. (Silicon rubber roller)
Forms images.
Transfers images onto the drum.
Picks up the manual feed paper. (In multi feed only)
Tray for manual feed paper
Transport the paper from the manual paper feed port.
Takes synchronization between the lead edge and the rear edge of the paper.
Picks up a sheet of paper from the cassette.
Picks up documents.
Separates documents to feed properly.
Feeds documents to the scanning section.
Discharges documents.
FO-DC550 EXTERNAL VIEWS AND INTERNAL STRUCTURES 4 - 6
[5] UNPACKING AND INSTALLATION
2. Cautions on handling
1. Copier installation
Be careful in handling the copier as follows to maintain the performance of this copier.
Improper installation may damage the copier. Please note the following
during initial installation and whenever the copier is moved.
Do not drop the copier, subject it to shock or strike it against any
object.
Caution: If the copier is moved from a cool place to a warm place, condensation may form inside the copier. Operation in this condition will cause poor copy quality and malfunctions.
Leave the copier at room temperature for at least 2 hours
before use.
Do not install your copier in areas that are:
• damp, humid, or very dusty
Do not expose the drum cartridge to direct sunlight.
Doing so will damage the surface (green portion) of the drum cartridge,
causing poor print quality.
• exposed to direct sunlight
• poorly ventilated
Store spare supplies such as drum cartridges and TD cartridges in a
dark place without removing from the package before use.
If they are exposed to direct sunlight, poor print quality may result.
Do not touch the surface (green portion) of the drum cartridge.
• subject to extreme temperature or humidity changes, e.g., near an
air conditioner or heater.
Doing so will damage the surface of the cartridge, causing poor print
quality.
3. Checking packed components and
accessories
Open the carton and check if the following components and accessories are included.
The copier should be installed near an accessible power outlet for easy
connection.
Be sure to connect the power cord only to a power outlet that meets
the specified voltage and current requirements.
Also make certain the outlet is properly grounded.
Be sure to allow the required space around the machine for servicing
and proper ventilation.
• Operation manual
• Operation manual
(For Facsimile)
Software CD-ROM
Core
8" (20cm)
8"(20cm)
Telephone line cord
4"
(10cm)
4"
(10cm)
TD cartridge
FO-DC550 UNPACKING AND INSTALLATION 5 - 1
Drum cartridge
(installed in machine)
4. Unpacking
Be sure to hold the handles on both sides of the machine to unpack the
machine and carry it to the installation location.
2) Remove the CAUTION tape from the front cover and remove the
two protective pins from the fusing machine by pulling the strings
upward one at a time.
Protective pins
CAUTION tape
3) Press gently on both sides of the front cover to open the cover.
5. Removing protective packing materials
1) Remove all pieces of tape shown in the illustration below and then
open the RSPF and remove the protective materials. Take out the
bag containing the TD cartridge.
4) Remove the TD cartridge from the bag. Remove the protective
paper. Hold the cartridge on both sides and shake it horizontally
four or five times. Hold the tab of the protective cover and pull the
tab to your side to remove the cover.
4 or 5 times
2) Release the scan head locking switch.
Grasp here and turn in
the direction of the arrow.
5) While pushing the lock release button, gently insert the TD cartridge until it locks into place.
Lock release button
Lock
Unlock
6. Installing the TD cartridge
1) Open the bypass tray, and then open the side cover.
6) Close the front cover and then the side cover by pressing the round
projections near the side cover open button.
Note: When closing the covers, be sure to close the front cover
securely and then close the side cover. If the covers are closed
in the wrong order, the covers may be damaged.
7) Ensure that the power switch of the machine is in the OFF position.
Plug the other end of the power cord into the nearest outlet.
FO-DC550 UNPACKING AND INSTALLATION 5 - 2
7. Loading the paper tray
Note: Make sure that the paper is not torn, is free of dust, and has no
wrinkles or curled edges.
1) Raise the handle of the paper tray and pull the paper tray out until it
stops.
6) Gently push the paper tray back into the machine.
Note:
2) Remove the pressure plate lock. Rotate the pressure plate lock in
the direction of the arrow to remove it while pressing down on the
pressure plate of the paper tray.
3) Store the pressure plate lock which has been removed in step 2. To
store the pressure plate lock, rotate the lock to secure it as shown
below.
• If you loaded a different size of paper than was loaded previously in
the tray.
• When not using the machine for an extended period, remove all
paper from the paper tray and store it in a dry place. If paper is left in
the machine for an extended period, the paper will absorb moisture
from the air, resulting in paper jams.
8. Connect the FAX modem PWB line cable
Connect the line cable to the FAX modem PWB.
To set up a telephone, wrap the line cable twice around the core, and
connect it to the FAX modem PWB as shown.
Pressure plate lock
4) Squeeze the lock lever of the front guide and slide the front guide to
match the width of the paper, and move the left guide to the appropriate slot as marked on the tray.
9. Power to copier
Front
guide
Left
guide
• The front guide is a slide-type guide. Grasp the locking knob on
the guide and slide the guide to the indicator line of the paper to
be loaded.
• The left guide is an insert-type guide. Remove it and then insert it
at the indicator line of the paper to be loaded.
5) Fan the paper and insert it into the tray. Make sure that the edges
go under the corner hooks.
Note:
• Do not load paper above the maximum height line (
Exceeding the line will cause a paper misfeed.
).
• If the paper is not fanned, double-feeds or misfeeds may occur.
• Make sure the stack of paper is straight before loading it. When adding paper, take the remaining paper out and combine it into a single
stack with the new paper.
• Make sure that all the paper in the stack is the same size and type.
• When loading paper, ensure that there is no space between the
paper and the guide, and make sure that the guide is not set too narrow and causes the paper to bend. Incorrect loading will cause the
paper to skew or misfeed.
1) Ensure that the power switch of the copier is in the OFF position.
Insert the attached power cord into the power cord socket at the
rear of the copier.
2) Plug the other end of the power cord into the nearest outlet.
10. Software for FO-DC550
The CD-ROM that accompanies the machine contains the following
software:
MFP driver
Printer driver
The printer driver enables you to use the printer function of the
machine.
The printer driver includes the Print Status Window*. This is a utility
that monitors the machine and informs you of the printing status, the
name of the document currently being printed, and error messages.
* When the machine is connected through the parallel port, the Print
Status Window can only be used when the parallel port is set to ECP
mode. To set the parallel port mode, refer to your computer manual
or ask the manufacturer of your computer.
Scanner driver (USB only)
The scanner driver allows you to use the scanning function of the
machine with TWAIN-compliant and WIA-compliant applications.
FO-DC550 UNPACKING AND INSTALLATION 5 - 3
Sharpdesk
B. Installing the software
Sharpdesk is an integrated software environment that makes it easy to
manage documents and image files, and launch applications.
Note:
Button Manager
Button Manager allows you to use the scanner menus on the machine
to scan a document.
Note: The scanning feature can only be used with computers that are
running Windows 98/Me/2000/XP and are connected to the
machine by a USB cable. If you are running Windows 95/NT 4.0
or are connected to the machine by a parallel connection, only
the printer function can be used.
A. Before installation
(1) Hardware and software requirements
Check the following hardware and software requirements in order to
install the software.
Computer type
Operating
system*3 *4
Display
Hard disk free
space
Other hardware
requirements
IBM PC/AT or compatible computer equipped with
a USB2.0*1/1.1*2 or bi-directional parallel interface
(IEEE1284)
Windows 95, Windows 98, Windows Me, Windows
NT Workstation 4.0 (ServicePack 5 or later)*5,
Windows 2000 Professional*5, Windows XP
Professional*5, Windows XP Home Edition*5
800 x 600 dots (SVGA) display with 256 colors (or
better)
150MB or more
An environment on which any of the operating
systems listed above can fully operate
*1 The machine's USB connector will transfer data at the speed specified by the USB 2.0 (Hi-Speed) only if the Microsoft USB 2.0 driver is
preinstalled in the computer, or if the USB 2.0 driver for Windows
2000 Professional/XP that Microsoft provides through its "Windows
Update" is installed.
2
* Compatible with Windows 98, Windows Me, Windows 2000 Professional, Windows XP Professional or Windows XP Home Edition preinstalled model equipped with a USB port.
*3 Printing is not available in MS-DOS mode.
*4 The machine does not support printing from a Macintosh environment.
*5 Administrator's rights are required to install the software using the
installer.
(2) Installation environment and usable software
The following table shows the drivers and software that can be
installed for each version of Windows and interface connection
method.
Cable
USB*1
Operating
system
MFP Driver
Printer
Scanner
driver
driver
Windows 98/
Me/2000/XP
Available
Parallel Windows 95/
*2
98/Me/NT 4.0/
2000/XP
Button
Sharpdesk
Manager
• If you need to use a different connection method after installing the
software based on a USB or parallel connection, you must first uninstall the software and then install it using the new connection
method.
• In the following explanations it is assumed that the mouse is configured for right hand operation.
• The scanner feature only works when using a USB cable.
• If an error message appears, follow the instructions on the screen to
solve the problem. After the problem is solved, the installation procedure will continue. Depending on the problem, you may have to click
the "Cancel" button to exit the installer. In this case, reinstall the software from the beginning after solving the problem.
[Standard installation (USB only)]
The procedure for a standard installation of the software is explained
below. If the machine is connected by a USB cable, it is recommended
that you use the standard installation.
Note: The standard installation can only be used when the machine is
connected by a USB cable. If the machine is connected by a
parallel cable, use the custom installation procedure.
1) The USB cable must not be connected to the machine. Make sure
that the cable is not connected before proceeding.
If the cable is connected, a Plug and Play window will appear. If this
happens, click the "Cancel" button to close the window and disconnect the cable.
Note: The cable will be connected in step 9).
2) Insert the CD-ROM into your computer's CD-ROM drive.
3) Click the "start" button, click "My Computer", and then double-click
the CD-ROM icon.
In Windows 98/Me/2000, double-click "My Computer", and then
double-click the CD-ROM icon.
4) Double-click the "setup" icon.
Note: If the language selection screen appears after you double click
the "setup" icon, select the language that you wish to use and
click the "Next" button. (Normally the correct language is
selected automatically.)
5) The "SOFTWARE LICENSE" window will appear. Make sure that
you understand the contents of the software license, and then click
the "Yes" button.
6) Read the "Readme First" in the "Welcome" window and then click
the "Next" button.
7) Click the "Standard" button.
"Integrated Installer is preparing..." will appear and then installation
of the MFP driver, Button Manager, and Sharpdesk will begin automatically.
Follow the on-screen instructions.
Available
Not Available*3
*1 Windows 98/Me does not support USB 2.0. A USB 2.0 connection
can be used in Windows 98/Me, however, the performance will be
the same as USB 1.1. The print speed based on USB 2.0 specifications can only be attained if your computer is running Windows
2000/XP, you are using a cable that supports USB 2.0 (USB 1.1 or
USB 2.0 certified), and the cable is connected to a USB 2.0 port on
your computer. If the connection is made through a hub, the hub
must support USB 2.0.
*2 The printer driver that is installed will vary depending on the type of
connection between the machine and your computer.
*3 Although it is possible to install Button Manager and Sharpdesk on
Windows 98/Me/2000/XP, neither Button Manager nor the scanner
function of Sharpdesk can actually be used.
FO-DC550 UNPACKING AND INSTALLATION 5 - 4
8) When the "Finish" screen appears, click the "Close" button.
7) Click the "Custom" button.
A message will appear instructing you to connect the machine to
your computer. Click the "OK" button.
Caution: If you are running Windows 2000/XP and a warning message
appears regarding the Windows logo test or digital signature,
be sure to click "Continue Anyway" or "Yes".
Note: After the installation, a message prompting you to restart your
computer may appear. In this case, click the "Yes" button to
restart your computer.
9) Make sure that the power of the machine is turned on, and then
connect the USB cable.
Windows will detect the machine and a Plug and Play screen will
appear.
Caution: If the following message appears on your computer screen,
close it.
8) Click the "MFP Driver" button.
A window regarding "HI-SPEED USB Device" will then
appear. Close the window.
To view detailed information on the software, click the "Display
Readme" button.
This message appears when the machine's USB 2.0 mode is
not set to "HI-SPEED". For information on switching the USB
2.0 mode.
10) Follow the instructions in the plug and play window to install the
MFP driver.
Follow the on-screen instructions.
Caution: If you are running Windows 2000/XP and a warning message
appears regarding the Windows logo test or digital signature,
be sure to click "Continue Anyway" or "Yes".
Note: A "USB 2.0 Composite Device" installation window may appear
prior to this procedure. In this case, follow the instructions in the
window to install the USB 2.0 Composite Device.
This completes the installation of the MFP driver.
• If you installed Button Manager, set up Button Manager as explained
in "C. SETTING UP BUTTON MANAGER".
[Custom installation]
The procedure for a custom installation of the software is explained
below. Use the custom installation procedure when the machine is
connected by a parallel cable, when the machine is used as a shared
printer on a network, or when you wish to install the MFP driver, Button
Manager, or Sharpdesk separately.
(1) Windows XP (USB/Parallel)
1) The USB/parallel cable must not be connected to the machine.
Make sure that the cable is not connected before proceeding.
9) The "Welcome" window will appear. Click the "Next" button.
10) When you are asked how the printer is connected, select "Connected to this computer" and click the "Next" button.
If you are using the machine as a shared printer on a network,
select "Connected via the network". For more information on this
setting, see "Using the machine as a shared printer".
Follow the on-screen instructions.
If the cable is connected, a Plug and Play window will appear. If this
happens, click the "Cancel" button to close the window and disconnect the cable.
Note: The cable will be connected in step 14).
2) Insert the CD-ROM into your computer's CD-ROM drive.
3) Click the "start" button, click "My Computer", and then double-click
the CD-ROM icon.
In Windows 98/Me/2000, double-click "My Computer", and then
double-click the CD-ROM icon.
4) Double-click the "setup" icon.
Note: If the language selection screen appears after you double click
the "setup" icon, select the language that you wish to use and
click the "Next" button. (Normally the correct language is
selected automatically.)
5) The "SOFTWARE LICENSE" window will appear. Make sure that
you understand the contents of the software license, and then click
the "Yes" button.
Caution: If you are running Windows XP and a warning message
appears regarding the Windows logo test or digital signature,
be sure to click "Continue Anyway".
6) Read the "Readme First" in the "Welcome" window and then click
the "Next" button.
FO-DC550 UNPACKING AND INSTALLATION 5 - 5
11) You will return to the window of step 8). If you wish to install Button Manager or Sharpdesk, click the "Utility Software" button.
14) Make sure that the power of the machine is turned on, and then
connect the USB/parallel cable.
If you do not wish to install the Utility Software, click the "Close"
button and go to step 14).
Windows will detect the machine and a Plug and Play screen will
appear.
Note: After the installation, a message prompting you to restart your
computer may appear. In this case, click the "Yes" button to
restart your computer.
Caution: If the following message appears on your computer screen,
close it.
Installing the Utility Software
12) Click the "Button Manager" button.
To view detailed information on the software, click the "Display
Readme" button.
Follow the on-screen instructions.
If you wish to install Sharpdesk, click the "Sharpdesk" button in
this window and follow the on-screen instructions.
Caution:
• Button Manager can only be used when the machine is connected
by a USB cable.
• The scanner function of Sharpdesk can only be used when the
machine is connected by a USB cable.
A window regarding "HI-SPEED USB Device" will then
appear. Close the window.
This message appears when the machine's USB 2.0 mode is
not set to "HI-SPEED". For information on switching the USB
2.0 mode.
15) Follow the instructions in the plug and play window to install the
MFP driver.
Follow the on-screen instructions.
Caution: If you are running Windows XP and a warning message
appears regarding the Windows logo test or digital signature,
be sure to click "Continue Anyway".
Note: A "USB 2.0 Composite Device" installation window may appear
prior to this procedure. In this case, follow the instructions in the
window to install the USB 2.0 Composite Device.
This completes the installation of the MFP driver.
• If you installed Button Manager, set up Button Manager as explained
in "C. Setting up button manager".
(2) Windows 98/Me/2000 (USB)
1) The USB cable must not be connected to the machine. Make sure
that the cable is not connected before proceeding.
If the cable is connected, a Plug and Play window will appear. If this
happens, click the "Cancel" button to close the window and disconnect the cable.
Note: The cable will be connected in step 8).
2) Perform steps 2) through 7) in "Custom installation".
Caution: If the following screen appears during installation of Sharpdesk, click the "Skip" button or the "Continue" button as
appropriate to continue the Sharpdesk installation.
3) Click the "MFP Driver" button.
To view detailed information on the software, click the "Display
Readme" button.
If "Skip" is selected, the Sharpdesk installation will continue
without installing Sharpdesk imaging.
If "Continue" is selected, Sharpdesk Imaging will be installed.
If Imaging for Windows is installed on your computer, Sharpdesk Imaging will overwrite Imaging for Windows.
13) When installation of Button Manager is finished, you will return to
the window of step 12). Click the "Close" button.
4) The "Welcome" window will appear. Click the "Next" button.
A message will appear instructing you to connect the machine to
your computer. Click the "OK" button.
Note: After the installation, a message prompting you to restart your
computer may appear. In this case, click the "Yes" button to
restart your computer.
FO-DC550 UNPACKING AND INSTALLATION 5 - 6
5) When you are asked how the printer is connected, select "Connected to this computer" and click the "Next" button.
(3) Windows 95/98/Me/NT 4.0/2000 (Parallel)
1) The parallel cable must not be connected to the machine. Make
sure that the cable is not connected before proceeding.
If the cable is connected, a Plug and Play window will appear. If this
happens, click the "Cancel" button to close the window and disconnect the cable.
Note: The cable will be connected in step 10).
2) Perform steps 2) through 7) in "Custom installation".
3) Click the "MFP Driver" button.
To view detailed information on the software, click the "Display
Readme" button.
Note: In Windows 95/NT4.0, the "Utility Software" button does not
appear and only the printer driver can be installed.
6) When the interface selection screen appears, select "USB" and
click the "Next" button.
If you are using the machine as a shared printer on a network,
select "Connected via the network". For more information on this
setting, see "Using the machine as a shared printer".
Follow the on-screen instructions.
4) The "Welcome" window will appear. Click the "Next" button.
5) When you are asked how the printer is connected, select "Connected to this computer" and click the "Next" button.
Caution: If you are running Windows 2000 and a warning message
appears regarding the Windows logo test or digital signature,
be sure to click "Yes".
If you are using the machine as a shared printer on a network,
select "Connected via the network". For more information on this
setting, see "Using the machine as a shared printer".
7) You will return to the window of step 3). If you wish to install Button
Manager or Sharpdesk, click the "Utility Software" button.
To install the Utility Software, see "Installing the Utility Software"
(steps 12) and 13) on page 7).
If you do not wish to install the Utility Software, click the "Close"
button.
A message will appear instructing you to connect the machine to
your computer. Click the "OK" button.
Note: After the installation, a message prompting you to restart your
computer may appear. In this case, click the "Yes" button to
restart your computer.
8) Make sure that the power of the machine is turned on, and then
connect the USB cable.
Windows will detect the machine and a Plug and Play screen will
appear.
6) When the interface selection screen appears, select "Parallel" and
click the "Next" button.
9) Follow the instructions in the plug and play window to install the
MFP driver.
Follow the on-screen instructions.
Caution: If you are running Windows 2000 and a warning message
appears regarding the Windows logo test or digital signature,
be sure to click "Yes".
Note: A "USB 2.0 Composite Device" installation window may appear
prior to this procedure. In this case, follow the instructions in the
window to install the USB 2.0 Composite Device.
This completes the installation of the MFP driver.
• If you installed Button Manager, set up Button Manager as explained
in "C. Setting up button manager".
FO-DC550 UNPACKING AND INSTALLATION 5 - 7
7) Select the printer port and whether the machine is to be used as the
default printer, make the selections and click the "Next" button.
Select "LPT1" for the printer port.
2) Click the "MFP Driver" button.
To view detailed information on the software, click the "Display
Readme" button.
Note:
• If "LPT1" does not appear, another printer or peripheral device is
using LPT1. In this case continue the installation, and after the
installation is finished, change the port setting so that the machine
can use LPT1.
• The "Add Network port" button is used when the machine is used as
a shared printer. Do not click this button here.
8) When the model selection window appears, select model name of
your machine and click the "Next" button.
3) The "Welcome" window will appear. Click the "Next" button.
4) When you are asked how the printer is connected, select "Connected via the network" and click the "Next" button.
Follow the on-screen instructions.
Caution: If you are running Windows 2000 and a warning message
appears regarding the Windows logo test or digital signature,
be sure to click "Yes".
9) You will return to the window of step 3). If you wish to install Sharpdesk, click the "Utility Software" button.
To install the Utility Software, see "Installing the Utility Software"
(steps 12) and 13) on page 7).
If you do not wish to install the Utility Software, click the "Close"
button.
A message will appear instructing you to connect the machine to
your computer. Click the "OK" button.
10) Make sure that the power of the machine is turned on, and then
connect the parallel cable.
5) When you are asked to select the printer port to be used, click the
"Add Network Port" button.
This completes the installation of the MFP driver.
(4) Using the machine as a shared printer
If the machine will be used as a shared printer on a network, follow
these steps to install the MFP driver in the client computer.
Note:
• To configure the appropriate settings in the print server, see the
operation manual or help file of your operating system.
"Print server" as explained here is a computer that is directly connected to the machine, and a "Client" is any other computer that is
connected to the same network.
• When the machine is used via a network connection, only the printer
function can be used; the scanner function cannot be used.
1) Perform steps 2) through 7) in "Custom installation".
FO-DC550 UNPACKING AND INSTALLATION 5 - 8
6) Select the network printer that is shared and click the "OK" button.
4) Select "SC1:" from the "Select an event" pull-down menu.
Ask your network administrator for the server name and printer
name of the machine on the network.
7) In the printer port selection window, verify the network printer that is
shared and whether the machine is to be used as the default
printer, make the selections and click the "Next" button.
5) Select "Start this program" and then select "Sharp Button Manager
F" from the pull-down menu.
8) When you are asked to select the model name, select the model
that you are using and click the "Next" button.
Follow the on-screen instructions.
Caution: If you are running Windows 2000/XP and a warning message
appears regarding the Windows logo test or digital signature,
be sure to click "Continue Anyway" or "Yes".
9) You will return to the window of step 2). Click the "Close" button.
Note: After the installation, a message prompting you to restart your
computer may appear. In this case, click the "Yes" button to
restart your computer.
This completes the installation of the MFP driver.
C. Setting up button manager
Button Manager is a software program that works with the scanner
driver to enable scanning from the machine.
To scan using the machine, Button Manager must be linked with the
scan menu on the machine. Follow the steps below to link Button Manager to scanner events.
6) Click the "Apply" button.
(1) Windows XP
1) Click the "start" button, click "Control Panel", click "Printers and
Other Hardware", and then click "Scanners and Cameras".
2) Click the "SHARP FO-DC550" icon and select "Properties" from the
"File" menu.
3) In the "Properties" screen, click the "Events" tab.
7) Repeat Steps 4) through 6) to link Button Manager to "SC2:"
through "SC6:".
Select "SC2:" from the "Select an event" pull-down menu. Select
"Start this program", select "Sharp Button Manager E" from the pulldown menu, and then click the "Apply" button. Do the same for
each ScanMenu through "SC6:".
When the settings have been completed, click the "OK" button to
close the screen.
Button Manager is now linked to the scan menu (1 through 6).
The scan settings for each of scan menu 1 through 6 can be changed
with the setting window of Button Manager.
For the factory default settings of the scan menu and the procedures
for configuring Button Manager settings.
(2) Windows 98/Me/2000
1) Click the "Start" button, select "Settings", and then click "Control
Panel".
2) Double-click the "Scanners and Cameras" icon.
Note: If the "Scanners and Cameras" icon does not appear in
Windows Me, click "view all Control Panel options".
3) Select "SHARP FO-DC550" and click the "Properties" button.
In Windows Me, right click "SHARP FO-DC550" and click "Properties" in the pop-up menu.
4) In the "Properties" screen, click the "Events" tab.
FO-DC550 UNPACKING AND INSTALLATION 5 - 9
5) Select "SC1:" from the "Scanner events" pull-down menu.
D. Connecting the machine to your computer
(1) Connecting a USB cable
Follow the procedure below to connect the machine to your computer.
A USB cable for connecting the machine to your computer is not
included with the machine. Please purchase the appropriate cable for
your computer.
Caution:
• USB is available with a PC/AT compatible computer that was originally equipped with USB and had Windows 98, Windows Me, Windows 2000 Professional, Windows XP Professional or Windows XP
Home Edition preinstalled.
• Do not connect the USB cable before installing the MFP driver. The
USB cable should be connected during installation of the MFP
driver.
Note:
• If the machine will be connected using a USB 2.0 port of your computer, please purchase a USB cable that supports USB 2.0.
6) Select "Sharp Button Manager F" in "Send to this application".
• The machine's USB connector will transfer data at the speed specified by the USB 2.0 (Hi-Speed) only if the Microsoft USB 2.0 driver is
preinstalled in the computer, or if the USB 2.0 driver for Windows
2000 Professional/XP that Microsoft provides through its "Windows
Update" Web page is installed.
• To obtain the fastest USB 2.0 data transfer speed, "USB2.0 MODE
SWITCH" in the machine's user programs must be set to "HISPEED".
• Use the machine's "HI-SPEED" mode only when using a computer
that is running Windows 2000/XP.
• Even when the Microsoft USB 2.0 driver is used, it may not be possible to obtain full USB 2.0 speed if a PC card supporting USB 2.0 is
used. To obtain the latest driver (which may enable a higher speed),
contact the manufacturer of your PC card.
• Connection is also possible using a USB 1.1 port on your computer.
However, the specifications will be USB 1.1 specifications (FullSpeed).
1) Insert the cable into the USB connector on the machine.
Note: If other applications are shown, deselect the checkboxes for the
other applications and leave only the Button Manager checkbox
selected.
7) Click the "Apply" button.
8) Repeat Steps 5) through 7) to link Button Manager to "SC2:"
through "SC6:".
Select "SC2:" from the "Scanner events" pull-down menu. Select
"Sharp Button Manager E" in "Send to this application" and click the
"Apply" button. Do the same for each ScanMenu through "SC6:".
When the settings have been completed, click the "OK" button to
close the screen.
2) Insert the other end of the cable into your computer's USB port.
(2) Connecting a parallel cable
1) Obtain an IEEE1284 shielded parallel interface cable.
2) Insert the cable into the parallel interface connector located on the
rear of the unit, and fasten with clasps.
Button Manager is now linked to the scan menu (1 through 6).
The scan settings for each of scan menus 1 through 6 can be changed
with the setting window of Button Manager.
For the factory default settings of the scan menu and the procedures
for configuring Button Manager settings.
3) Insert the other end of the cable into the interface connector of your
computer.
FO-DC550 UNPACKING AND INSTALLATION 5 - 10
11. Interface
A. USB
Connector
4-pin ACON UBR23-4K2200
Type-B connector
Cable
Shielded twisted pair cable
(2 m (6 feet) Max.: high-speed transmission equivalent)
Pin configuration
Pin No.
1
2
3
4
5
6
7
8
9
10
Signal name
STB
DATA1
DATA2
DATA3
DATA4
DATA5
DATA6
DATA7
DATA8
ACKNLG
Pin No.
19
20
21
22
23
24
25
26
27
28
The pin numbers and signal names are listed in the following table.
Pin No.
1
2
3
4
2
11
12
13
14
15
16
17
18
Signal name
+5V
-DATA
+DATA
GND
1
BUSY
PE (Paper End)
SLTC
AUTO LF
(NC)
GND (0 V)
FG
+5 V
29
30
31
32
33
34
35
36
Signal name
GND (STB RET)
GND (DATA1 RET)
GND (DATA2 RET)
GND (DATA3 RET)
GND (DATA4 RET)
GND (DATA5 RET)
GND (DATA6 RET)
GND (DATA7 RET)
GND (DATA8 RET)
GND
(ACKNLG RET)
GND (BUSY RET)
GND (PE RET)
INPRM
FAULT
(NC)
(NC)
+5 V
SLTC IN
12. Moving
Moving instructions
When moving the unit, follow the procedure below.
Note: When moving this unit, be sure to remove the TD cartridge in
advance.
1) Turn the power switch off and remove the power cord from the outlet.
3
2) Open the side cover and front cover, in that order. Remove the TD
cartridge and close the front cover and side cover, in that order.
4
To open and close the side cover and front cover, and to remove
the TD cartridge.
B. Parallel interface
This printer uses a bi-directional parallel interface. Use the supplied
interface cable.
3) Raise the handle of the paper tray and pull the paper tray out until it
stops.
Connector
4) Push the center of the pressure plate down until it locks in place
and lock the plate using the pressure plate lock which has been
stored in the front of the paper tray.
36-pin ACON RBE42-36K1153 female connector or equivalent connector
5) Push the paper tray back into the unit.
Cable
Shielded type bi-directional parallel interface For best results, use a
printer interface cable which is IEEE1284 compliant.
Pin configuration
The pin numbers and signal names are listed in the following table.
18
1
36
19
6) Lock the scan head locking switch.
Note: When shipping the unit, the scan head locking switch must be
locked to prevent shipping damage.
7) Close the multi-bypass tray and the paper output tray extension,
and attach the packing materials and tape which were removed
during installation of the unit.
8) Pack the unit into the carton.
FO-DC550 UNPACKING AND INSTALLATION 5 - 11
[6] COPY PROCESS
An OPC drum is used for the photoconductor.
(Structure of the OPC drum layers)
OPC layer
(20 microns thick)
Pigment layer (0.2
to 0.3 microns thick)
Aluminum drum
1. Functional diagram
Main charger
Laser beam
Cleaning blade
MG roller
Drum
Transfer unit
Resist roller
(Basic operation cycle)
Semiconductor laser
Focus correction lens
Main high voltage unit
Exposure
Charge
Saw tooth
Toner
Drum
Developing
Cleaning
Developer
Cleaning blade
PS roller
Waste toner box
To face
down tray
Paper release
Fusing
Separation
Transfer
Heat roller
Electrode
Transfer charger
Heater lamp
Transfer high
voltage unit
Synchronization
with drum
Manual feed
Cassette
paper feed
Print process
Paper transport route
FO-DC550 COPY PROCESS 6 - 1
2. Outline of print process
Step-2: Exposure (laser beam, lens)
This printer is a non-impact printer that uses a semiconductor laser
and electrostatic print process. This printer uses an OPC (Organic
Photo Conductor) for its photoconductive material.
First, voltage from the main corona unit charges the drum surface and
a latent image is formed on the drum surface using a laser beam. This
latent image forms a visible image on the drum surface when toner is
applied. The toner image is then transferred onto the print paper by the
transfer corona and fused on the print paper in the fusing section with
a combination of heat and pressure.
Step-1: Charge
Step-2: Exposure
* Latent image is formed on the drum.
Step-3: Developing
Latent image formed on the drum is then changed into visible
image with toner.
Step-4: Transfer
The visible image (toner image) on the drum is transferred
onto the print paper.
Step-5: Cleaning
Residual toner on the drum surface is removed and collected
by the cleaning blade.
Step-6: Optical discharge
Residual charge on the drum surface is removed, by
semiconductor laser beam.
3. Actual print process
A Laser beam is generated from the semiconductor laser and
controlled by the print pattern signal. The laser writes onto the OPC
drum surface through the polygon mirrors and lens. The resistance of
the OPC layer decreases for an area exposed by the laser beam
(corresponding to the print pattern signal). The beam neutralizes the
negative charge. An electrostatic latent image is formed on the drum
surface.
Semiconductor laser
Exposure
(semiconductor laser)
OPC layer
Pigment
layer
Aluminum
drum
Drum surface charge
after the exposure
Step-1: DC charge
A uniform negative charge is applied over the OPC drum surface by
the main charging unit. Stable potential is maintained by means of the
Scorotron charger.
Positive charges are generated in the aluminum layer.
About
DC5.5KV
( 580V/ 400V)
FO-DC550 COPY PROCESS 6 - 2
Non-image area
Image area
OPC layer
Pigment
layer
Aluminum
layer
Step-3: Developing (DC bias)
Step-4: Transfer
A bias potential is applied to the MG roller in the two component
magnetic brush developing method, and the toner is charged negative
through friction with the carrier.
Non-image area of the drum surface charged with negative potential
repel the toner, whereas the laser exposed portions where no negative
charges exist, attract the toner. As a result, a visible image appears on
the drum surface.
The visible image on the drum surface is transferred onto the print
paper by applying a positive charge from the transfer corona to the
backside of the print paper.
:Carrier (Magnetized particle)
:Toner (Charge negative by friction)
(N) (S) Permanent magnet
(provided in three locations)
N
S
N
About DC 5.2kV
DC
400V 8V
MG roller
Step-5: Separation
Since the print paper is charged positively by the transfer corona, it is
discharged by the separation corona. The separation corona is
connected to ground.
Step-6: Cleaning
Toner remaining on the drum is removed and collected by the cleaning
blade. It is transported to the waste toner collecting section in the
cleaning unit by the waste toner transport roller.
Toner is attracted over the shadowed area because of the developing
bias.
FO-DC550 COPY PROCESS 6 - 3
Step-7: Optical discharge (Semiconductor laser)
Start
Before the drum rotation is stopped, the semiconductor laser is
radiated onto the drum to reduce the electrical resistance in the OPC
layer and eliminate residual charge, providing a uniform state to the
drum surface for the next page to be printed.
When the electrical resistance is reduced, positive charges on the
aluminum layer are moved and neutralized with negative charges on
the OPC layer.
1) Because the grid potential is at a low level, the drum potential is at
about -400V. (Carrier may not be attracted though the carrier is
pulled towards the drum by the electrostatic force of -400V.
2) Developing bias (-400V) is applied when the photoconductor
potential is switched from LOW to HIGH.
3) Once developing bias (-400V) is applied and the photo conductor
potential rises to HIGH, toner will not be attracted to the drum.
Semiconductor laser
Stop
The reverse sequence takes place.
Retaining developing bias at an abnormal occurrence
Function
The developing bias will be lost if the power supply was removed
during print process. In this event, the drum potential slightly abates
and the carrier makes deposits on the drum because of strong static
power. To prevent this, the machine incorporates a function to retain
the developing bias for a certain period and decrease the voltage
gradually against possible power loss.
Charge by the Scorotron charger
Function
The Scorotron charger functions to maintain uniform surface potential
on the drum at all times, It control the surface potential regardless of
the charge characteristics of the photoconductor.
Basic function
A screen grid is placed between the saw tooth and the
photoconductor. A stable voltage is added to the screen grid to
maintain the corona current on the photoconductor.
As the photoconductor is charged by the saw tooth from the main
corona unit, the surface potential increases. This increases the current
flowing through the screen grid. When the photoconductor potential
nears the grid potential, the current turns to flow to the grid so that the
photoconductor potential can be maintained at a stable level.
Basic function
Normally, the developing bias voltage is retained for a certain time
before the drum comes to a complete stop if the machine should stop
before completing the normal print cycle. The developing bias can be
added before resuming the operation after an abnormal interruption.
Therefore, carrier will not make a deposit on the drum surface.
Process controlling
Function
The print pattern signal is converted into an invisible image by the
semiconductor laser using negative to positive (reversible) developing
method. Therefore, if the developing bias is added before the drum is
charged, toner is attracted onto the drum. If the developing bias is not
added when the drum is charged, the carrier is attracted to the drum
because of the strong electrostatic force of the drum.
To avoid this, the process is controlled by adjusting the drum potential
and the grid potential of the Scorotron charger.
Basic function
Voltage added to the screen grid can be selected, high and low. To
make it easily understood, the figure below shows voltage transition at
the developer unit.
0
START
STOP
Print potential
Toner attract
potential
Developing bias
2)
3)
1)
Low
4)
Drum potential
High
Time
FO-DC550 COPY PROCESS 6 - 4
[7] OPERATIONAL DESCRIPTIONS
1. Outline of operation
The outline of operation is described referring to the basic configuration.
(Basic configuration)
Operation
section
FAX
FAX modem
Scanner section
(Option)
CCD
Network
Network
Box
FAX I/F
USB
Printer/
Scanner I/F
MCU (Main control/image process section)
PC
USB or parallel
Note: The scanner function is effective
only by USB connection.
Network is for print only.
LSU (Laser unit)
Laser diode, Polygon mirror lens
Laser beam
Paper exit
Process section
Fusing section
Printer section
Paper transport section
Cassette paper
feed section
Manual paper
feed section
(Outline of copy operation)
Printing
Setting conditions
7) Electrostatic latent images are formed on the OPC drum according
to the laser beams, and the latent images are developed to be visible images(toner images).
1) Set copy conditions such as the copy quantity and the copy density
with the operation section, and press the COPY button. The information on copy conditions is sent to the MCU.
Image scanning
2) When the COPY button is pressed, the scanner section starts
scanning of images.
The light from the copy lamp is reflected by the document and
passed through the lens to the CCD.
Photo signal/Electric signal conversion
8) Meanwhile the paper is fed to the image transfer section in synchronization with the image lead edge.
9) After the transfer of toner images onto the paper, the toner images
are fused to the paper by the fusing section. The copied paper is
discharged onto the exit tray.
(Outline of printer operation)
3) The image is converted into electrical signals by the CCD circuit
and passed to the MCU.
The print data sent from the PC are passed through the I/F and the
MCU to the LSU. The procedures after that are the same as above 5)
and later.
Image process
(Outline of scanner operation)
4) The document image signal sent from the CCD circuit is processed
under the revised conditions and sent to the LSU (laser unit) as
print data.
The scan data are passed through the MCU and the I/F to the PC
according to the conditions requested by the PC or set by the operations with the operation panel.
Electric signal/Photo signal (laser beam) conversion
5) The LSU emits laser beams according to the print data.
(Electrical signals are converted into photo signals.)
6) The laser beams are radiated through the polygon mirror and various lenses to the OPC drum.
FO-DC550 OPERATIONAL DESCRIPTIONS 7 - 1
2. Scanner section
A. Scanner unit
The scanner unit in the digital copier scans images.
It is composed of the optical unit and the drive unit. The optical unit
performs scanning in the main scan direction with the light receiving
elements (color CCD). The drive unit performs scanning in the sub
scanning direction by moving the optical unit.
B. Optical system
Two white lamps are used as the light source.
Light radiated from the light source is applied to the document on the
document table. The reflected light from the document is reflected 5
times by No. 1 - No. 3 mirrors and passed through the reduction lens to
form images on the light-receiving surface of 3-line CCD.
The light-receiving surface of the color CCD is provided with 3 line
scanning sections for RGB. Separate images scanned in each color
section are overlapped to complete color scanning. (When PC scanning)
(Spectrum characteristics of the color CCD)
The resolution is 600dpi.
1
When copying, only the green component is used to print with the
printer.
8
9
10
8
9
The color component for printing can be switched to red or blue by the
service test command.
6
MBVM26W25W260NLH/G
6.00E-01
Intensity of UV
5.00E-01
Lamp : MBVM26W25W260NLH/G
Lamp current : 5mA
Temp. : 25 degree
4.00E-01
7
2
3
3.00E-01
4
5
2.00E-01
(Optical unit)
1.00E-01
0.00E+00
0
200
400
Wave length (nm)
600
800
1
4
7
Table glass
Mirror 1
CCD PWB
2
5
8
Optical unit
Mirror 2
Lamp
3
6
9
Lens
Mirror 3
Reflector
(Spectrum characteristics of the lamp)
C. Drive system
The drive system is composed of the scanner motor, the pulley gear,
the idle pulley, the idle gear, the belt 473, the belt 190, and the shaft.
The motor rotation is converted into reciprocated movements of the
belt 473 through the idle gear, the pulley gear, the belt 190, and the
idle pulley to drive the optical unit.
1
7
3
1
4
7
4
Scanner motor
Belt 473
Shaft
6
2
2
5
8
8
Pulley gear
Belt 190
Idle gear
FO-DC550 OPERATIONAL DESCRIPTIONS 7 - 2
5
3
6
9
Idle pulley
Optical unit
3
3. Laser unit
B. Laser beam path
The image data sent from the MCU (image process circuit) is sent to
the LSU (laser unit), where it is converted into laser beams.
A. Basic structure
The LSU unit is the writing section of the digital optical system.
The semiconductor laser is used as the light source, and images are
formed on the OPC drum by the polygon mirror and fθ lens, etc.
The laser beams are passed through the collimator lens, the cylindrical
lens, the polygon mirror, the fθ lens, and the mirror to form images on
the OPC drum in the main scanning direction. The laser emitting PWB
is provided with the APC (auto power control) in order to eliminate fluctuations in the laser power. The BD PWB works for measurement of
the laser writing start point.
4
3
2
1
C. Composition
Effective scanning width: 216mm (max.)
Resolution: 600dpi
Beam diameter: 75um in the main scanning direction, 80um in the sub
scanning direction
Image surface power: 0.15 ±0.01mW (Laser wavelength 770 - 795nm)
6
No
1
2
3
Component
Semiconductor laser
Collimator lens
CY lens
4
Polygon mirror,
polygon motor
5
BD (Mirror, lens,
PWB)
fθ lens
6
Polygon motor section: Brushless motor 31,180rpm
No. of mirror surfaces: 4 surfaces
5
Function
Generates laser beams.
Converges laser beams in parallel.
Converges laser beams onto the
polygon mirror surface.
Reflects laser beams at a constant
rpm.
(A four-surfaces polygon mirror is
used.)
Detects start timing of laser scanning.
4. Fuser section
Converges laser beams at a spot on
the drum.
Makes the laser scanning speeds at
both ends of the drum same as each
other. (Refer to the figure below.)
Makes the laser scanning speeds at both ends of the drum same as
each other.
a≠b≠c
a
b
d=e=f
c
d
e
f
f θ LENS
FO-DC550 OPERATIONAL DESCRIPTIONS 7 - 3
A. General description
2) The surface temperature of the upper heat roller is set to 165 190°C. The surface temperature during the power save mode is
set to 100°C.
General block diagram (cross section)
Thermal fuse
Separator pawl
PPD2
3) The self-check function comes active when one of the following
malfunctions occurs, and an "H" is displayed on the multicopy
window.
a. When the heat roller surface temperature rises above 240°C.
b. When the heat roller surface temperature drops below 100°C during
the copy cycle.
c. Open thermistor
d. Open thermal fuse
e. When the heat roller temperature does not reach 190°C within 27
second after supplying the power.
Thermistor
Pressure roller
Fusing resistor
Heat roller
This model is provided with a fusing resistor in the fusing section to
improve transfer efficiency.
Since the upper heat roller is conductive, when using copy paper that
contains moisture and the distance between the transfer unit and the
fusing unit is short, the transfer current may find a path to ground via
the copy paper, the upper heat roller and the discharging brush.
Paper guide
Top view
Heat roller
(4) Fusing resistor
Thermal fuse
Thermistor
Heater lamp
5. Paper feed section and paper transport
section
A. Paper transport path and general operations
4
3
5
Separator pawl
2
1
(1) Heat roller
A Teflon roller is used for the heat roller and a silicone rubber roller is
used for the lower heat roller for better toner fusing performance and
paper separation.
6
7
8
9
10
(2) Separator pawl
Three separator pawls are used on the upper heat roller. The separator pawls are Teflon coated to reduce friction with the roller and prevent
a smear on the paper caused by the separator pawl.
14 13 12
11
(3) Thermal control
1) The heater lamp, thermistor, main PWB, DC power supply PWB,
and triac within the power supply unit are used to control the
temperature in the fuser unit.
To prevent against abnormally high temperature in the fuser unit, a
thermal breaker and thermal fuse are used for safety purposes.
Heated by the heater
lamp. (800W)
Safety device
(thermal breaker, thermal
fuse)
Triac (in the
power supply unit)
The surface temperature
of the upper heat roller is
sensed by the thermistor.
1
Scanner unit
8
Drum
2
Copy lamp
9
Transfer unit
3
LSU (Laser unit)
10 Pickup roller
4
Paper exit roller
11 Manual paper feed tray
5
Main charger
12 Manual paper feed roller
6
Heat roller
13 PS roller unit
7
Pressure roller
14 Paper feed roller
Paper feed is made in two ways; the tray paper feed and the manual
paper feed. The tray is of universal-type, and has the capacity of 250
sheets.
The front loading system allows you to install or remove the tray from
the front cabinet.
The general descriptions on the tray paper feed and the manual paper
feed operation are given below.
Level of the thermistor is
controlled by the main PWB.
With the signal from the
main PWB, the triac is
controlled on and off.
(power supply PWB)
FO-DC550 OPERATIONAL DESCRIPTIONS 7 - 4
(1) Cassette paper feed operation
1) The figure below shows the positions of the pick-up roller, the
paper feed clutch sleeve, and the paper feed latch in the initial
state without pressing the COPY button after lighting the ready
lamp.
The paper feed latch is in contact with the projection of the clutch
sleeve.
5) At this time, the paper is fed passed the paper entry detection
switch (PPD1), and detected by it. After about 0.15 sec from
detection of paper by PPD1, the tray paper feed solenoid (PFS)
turns on so that the clutch sleeve projection comes into contact
with the paper feed latch to stop the pick-up roller. Then the pickup roller rotates for about 0.15 sec so that the lead edge of the
paper is evenly pressed on the resist roller, preventing against
skew feeding.
2) When the COPY button is pressed, the main drive motor starts
rotating to drive each drive gear.
The pick-up drive gear also is driven at that time. Since, however,
the paper feed latch is in contact with the projection of the clutch
sleeve, rotation of the drive gear is not transmitted to the pick-up
roller, which does not rotate therefore.
PFS
OFF
PFS
ON
OFF
6) To release the resist roller, the tray paper feed solenoid and the
resist solenoid are turned on by the paper start signal to disengage
the resist start latch from the clutch sleeve, transmitting rotation of
the resist drive gear to the resist roller shaft. Thus the paper is
transported by the resist roller.
7) After the resist roller starts rotating, the paper is passed through
the pre-transfer guide to the transfer section. Images are
transferred on the paper, which is separated from the OPC drum
by the drum curve and the separation section.
PFS
OFF
OFF
OFF
RRS
3) After about 0.1 sec from when the main motor start rotating, the
tray paper feed solenoid (PFS) turns on for a moment.
This disengages the paper feed latch from the projection of the
clutch sleeve, transmitting rotation of the pick-up drive gear to the
paper feed roller shaft, rotating the pick-up roller to feed the paper.
PFS
RRS
RRS
ON
RRS
OFF
8) The paper separated from the drum is passed through the fusing
paper guide, the heat roller (fusing section), POD (paper out
detector) to the copy tray.
4) After more than half rotation of the pick-up roller, the paper feed
latch is brought in contact with a notch on the clutch sleeve,
stopping rotation of the pick-up roller.
FO-DC550 OPERATIONAL DESCRIPTIONS 7 - 5
(2) Manual multi paper feed operation
1) Before paper feed operation, the manual paper feed solenoid
(MPFS) is turned OFF as shown in the figure below.
C
3) When pawl C of the manual paper feed clutch sleeve is engaged
with the manual feed latch, the manual feed stopper falls and the
manual take-up roller rises. At that time, the manual paper feed
roller is rotating.
A
A
C
OFF
MPFS
ON
MPFS
2) When the PRINT button is pressed, the manual paper feed
solenoid (MPFS) turns on to disengage the manual paper feed
latch.
A from the manual paper feed clutch sleeve A, rotating the manual
paper feed roller and the manual take-up roller. At the same time,
the manual paper feed stopper opens and the manual take-up
roller is pressed to the surface of the paper to start paper feeding.
4) The lead edge of the transported paper is pressed on the resist
roller by the transport roller. Then the paper is stopped temporarily
to allow synchronization with the lead edge of the image on the
OPC drum.
From this point, the operation is the same as the paper feed
operation from the tray. (Refer to A-5 - 8.)
5) The solenoid turns off to close the gate and return to the initial
state.
C
A
A
C
ON
MPFS
OFF
MPFS
FO-DC550 OPERATIONAL DESCRIPTIONS 7 - 6
(3) Conditions of occurrence of paper misfeed
C. Operational descriptions
a. When the power is turned on:
PPD or POD is ON when the power is turned on.
Time chart (Tray feed)
Document set
b. Copy operation
a
PPD1 jam
b
PPD2 jam
c
SPID ON
PPD1 does not turn off within 4 sec after turning
on the resist roller.
PPD2 is off immediately after turning on the
resist roller.
PPD2 does not turn off within 1.2 sec after
turning off the resist roller.
POD does not turn on within 2.9 sec after turning
on the resist roller.
POD does not turn off within 1.5 sec - 2.7 sec
after turning off PPD2.
POD jam
Document set sensor
Document feed unit lamp ON
PSW ON
MIRM rotation
(Copier side)
MM rotation
CPFS ON
6. RSPF section
Main motor rotation
Copy start
The scanner is shifted
to the exposure position.
(SPF side)
SPF motor rotation
SPFM rotation
Paper feed
SPUS ON
Document feed
SPPD ON
Document transport sensor
PPD ON
A. Outline
The RSPF (Reverse Single Path Feeder) is installed to the AR-168D
and the SPF (single path feeder) is installed to the AR-168S as a standard provision, and it automatically copies up to 30 sheets of documents of a same size. (Only one set of copies)
Synchronization
RRC ON
Paper transport
Document transport
(Transfer)
(Exposure)
(Fusing)
(Document exit)
B. Document transport path and basic composition
(RSPF)
POD ON
12
3 1 4 5
6 7
(Paper exit)
In the zooming mode, the magnification ratio in the sub
scanning direction (paper transport direction) is adjusted
by changing the document transport speed.
PSW
13 10 11
2
8 9
MIRR M
SPF M
CL
SPUS
SPPD
1
3
5
7
9
11
13
Pickup roller
Set detection ACT
Document feed roller
Paper entry sensor
Transport follower roller
Paper exit follower roller
Switch gate
2
4
6
8
10
12
Sheet of document for paper feed
Paper stopper
Separation sheet
PS roller D
Paper exit roller
Document tray
625msec
756msec
SCANST
752msec
MAIN M
CPFS1
RRS
PPD1
PPD2
POD
D. Cases where a document jam is caused
1) When SPPD is ON (document remaining) when the power is
turned on.
2) When SPPD is not turned ON within about 1.5 sec (at 100% copy)
after starting the document feed operation.
3) When SPPD is not turned on within about 4.7 sec (at 100% copy)
after turning on SPPD.
4) When the RSPF document jam release door or the OC cover is
opened during document transport (SPF motor rotating).
E. RSPF open/close detection (book document
detection)
RSPF open/close detection (book document) detection is performed
by detecting the interval between the reference lines on the white
Mylar attached to the paper exit guide (document scanning section) by
the scanner (CCD) and detecting the varied quantity.
B
A
(Floating)
(White Mylar)
Reference line
(CCD)
Reference line
B
A
FO-DC550 OPERATIONAL DESCRIPTIONS 7 - 7
A - B = Varied quantity of pixels
(pixel)
7. D-D (Duplex to Duplex) mode paper/
document transport (Duplex model)
C. Back copy
Document transport:
By switchback operation, the document is sent through the PS roller to
the exposure section, where the back of the document is exposed.
A. Initial state
Set duplex documents on the document tray.
Set paper on the cassette. (In the duplex mode, the manual feed tray
cannot be selected.)
• It is sent to the document exit section by the transport roller and the
paper exit roller.
B. Front copy
• R-SPF gate solenoid ON. The document is sent to the intermediate
tray, (but not discharged completely.)
Document transport:
• It is stopped once and switchback operation is performed.
The document feed roller feeds the document from the paper feed
roller to the PS roller.
• It is sent through the PS roller and the exposure section (without
exposure operation) to the document exit section.
• The document is exposed in the exposure section, and sent to the
document exit section
• R-SPF gate solenoid OFF
• by the transport/paper exit roller.
Paper transport:
• R-SPF gate solenoid ON
Switchback operation is performed.
• The document is sent to the intermediate tray.
(but not discharged completely.)
• The paper is sent through the upper side of the gate section and the
duplex transport section, and the PS roller, and the images on the
back are transferred.
• The document is stopped once, then switchback operation is
performed.
(To the back copy)
• The document is discharged to the document exit tray.
• It is sent through the fusing section and discharged to the paper exit
tray.
Paper transport:
The document is passed through the paper feed roller and the PS
roller by the paper feed roller
and the images on the front surface are transferred.
• The paper is passed through the fusing section and the lower side of
the gate section to the paper exit tray side, (but not discharged
completely.)
• It is stopped once and switchback operation is performed.
(To the back copy)
FO-DC550 OPERATIONAL DESCRIPTIONS 7 - 8
8. Shifter
Switchback operation is made after back copying in order to discharge
documents according to the setting.
Set document Documents after discharge,
1
2
3
4
with empty feed
4
3
2
1
without empty feed
3
4
1
2
There are following job modes as well as D-D mode.
S - S (Simplex to Simplex)
Shift width: 2.5cm
The offset function by the shifter is turned ON/OFF by the user program.
According to the setting, offset operation is performed for every job.
(Default: ON)
S - D (Simplex to Duplex),
Rotation copy mode (The back images are rotated 180°C.)
S - D (Simplex to Duplex), Copy mode without rotation
D - S (Duplex to Simplex)
Rotation copy mode:
The front and the back are in upside down each other.
Copy mode without rotation:
The front and the back are not in upside down.
FO-DC550 OPERATIONAL DESCRIPTIONS 7 - 9
[8] DISASSEMBLY AND ASSEMBLY
2) Push up the lock pawls (2 positions) of the side cover, and remove
the transfer charger.
Lock pawl rear
Before disassembly, be sure to disconnect the power cord for
safety.
1. Do not disconnect or connect the connector and the harness during the machine is powered. Especially be careful
not to disconnect or connect the harness between the MCU
PWB and the LSU (MCU PWB: CN20) during the machine is
powered. (If it is disconnected or connected during the
machine is powered, the IC inside the LSU will be
destroyed.)
1)
2. To disconnect the harness after turning on the power, be
sure to turn off the power and wait for at least 10 sec before
disconnection. (Note that a voltage still remains immediately after turning off the power.)
The disassembly and assembly procedures are described for the following sections:
1. High voltage section
2. Operation panel section
3. Optical section
2)
4. Fusing section
5. Tray paper feed/transport section
6. Manual paper feed section
Transfer
charger
7. Rear frame section
8. Power section
1)
9. Duplex motor section
10. Reverse roller section
11. RSPF section
1. High voltage section
Lock pawl rear
A. List
No.
Part name Ref.
1 Transfer charger unit
2 Charger wire
C. Assembly procedure
For assembly, reverse the disassembly procedure.
D. Charger wire cleaning
B. Disassembly procedure
1) Press the side cover open/close button and open the side cover.
1) Remove the charger cleaner from the manual paper feed unit.
1)
1)
2)
FO-DC550 DISASSEMBLY AND ASSEMBLY 8 - 1
2) Set the charger cleaner to the transfer unit, and move it reciprocally a few times in the direction of the arrow shown in the figure
below.
A. List
No.
Part name Ref.
1 Operation panel unit
2 Operation PWB
4)
3)
2. Operation panel section
B. Disassembly procedure
1) Open the side door, and Open the front cover.
2)
1)
1)
2)
2) Remove the screws (4 pcs.), the harness, and the operation panel
unit.
E. Charger wire replacement
1) Remove the TC cover and remove the screw.
1)
2) Remove the spring and remove the charger wire.
3) Install a new charger wire by reversing the procedures (1) and (2).
At that time, be careful of the following items.
• The rest of the charger wire must be within 1.5mm. Refer to Fig.1
• The spring hook section (charger wire winding section) must be in
the range of the projection section.
1)
• Be careful not to twist the charger wire.
3)
3)
1)
2)
Charger wire
1)
1)
2)
1)
1mm
Protrusion
1.5mm
Fig.1
FO-DC550 DISASSEMBLY AND ASSEMBLY 8 - 2
2) Remove the connector and the clamp, and remove the RSPF unit.
3) Remove four screws, and remove the operation cabinet.
4) Remove four screws, and remove the operation PWB.
1)
2)
1)
3)
3)
6)
6)
7)
1)
4)
1)
5)
4)
3)
2)
1)
3) Remove the four screws, remove the operation unit, and disconnect the connector.
Note that there are 9 pawls
4) Remove the right cabinet.
C. Assembly procedure
5) Remove the left cabinet.
For assembly, reverse the disassembly procedure
6) Remove the screw, and remove the rear cover.
7) Remove the table glass.
3. Optical section
A. List
NO.
Part name Ref.
1 Copy lamp unit
2 Copy lamp
3 Lens unit
6)
1)
7)
5)
8)
B. Disassembly procedure
1)
1) Remove four screws, and remove the rear cabinet and the rear
cabinet cover.
3)
1)
1)
1)
2)
2)
1)
2)
1)
1)
FO-DC550 DISASSEMBLY AND ASSEMBLY 8 - 3
4)
8) Move the carriage to the position indicated on the figure.
C. Assembly procedure
9) Loosen the screw which is fixing the tension plate.
CCD core
10) Move the tension plate in the arrow direction to release the tension, and remove the belt.
1) Pass the core through the CCD-MCU harness.
2) Insert the CCD-MCU harness into the CCD PWB connector of the
carriage unit.
3) Move the core which was passed through the CCD-MCU harness
near the CCD PWB connector as shown in the figure below, and fix
it with a filament tape (19mm wide, 40mm long). For the attachment reference, refer to the figure below. Clean and remove oil
from the attachment section.
3)
2)
4)
4) Attach the CCD-MCU harness to the duplex tape on the back of
the carriage unit.
5) Attach the PWB holder to the position specified in the figure below.
6) Pass the core through the FFC and the PWB holder, and fix the
core.
1)
Note: Attach the FCC to the base
plate securely with duplex tape to
prevent against coming loose.
11) Remove the screw, and remove the rod stopper.
12) Remove the rod.
3)
2)
1)
13) Lift the rear side of the carriage, remove the belt and the connector, and remove the carriage.
4)
1)
2)
3)
FO-DC550 DISASSEMBLY AND ASSEMBLY 8 - 4
Note: Attach the FCC to
fit with the marking line.
Marking line.
4. Fusing section
4) Remove the screw and remove the U-turn guide.
A. List
No.
1
2
3
4
5
Part name Ref.
Thermistor
PPD2 sensor
Heater lamp
Pressure roller
Heat roller
1)
2)
B. Disassembly procedure
1) Remove the connectors (3 pcs.) of the rear cabinet.
2) Open the side cover, remove two screws, and remove the fusing
unit.
Pressure roller section disassembly
5) Remove the three screws, remove the fusing cover lower on the
right side, and open the heat roller section.
2)
3)
1)
4)
6)
5)
1)
3)
2)
5)
6)
6) Remove the screw and remove the PPD2 sensor.
2)
1)
3) Cut the binding band, remove the screw, and remove the thermistor.
1)
2)
PPD2 sensor
2)
Thermistor
3)
FO-DC550 DISASSEMBLY AND ASSEMBLY 8 - 5
7) Remove the plate spring on the right and remove the heater lamp.
10) Remove the pressure release levers on the right and the left sides.
1)
1)
1)
2)
11) Remove the pressure roller, the pressure bearing, and the spring.
Note: Apply grease to the sections specified with an asterisk (*).
Grease: “JFE552” UKOG-0235FCZZ
Heater lamp
Pressure roller
8) Remove the spring and remove the separation pawls (3 pcs.).
1)
3)
3)
2)
1)
2)
2)
3)
Heat roller disassembly
(Continued from procedure (4).)
5) Remove screws, remove the fusing cover, and open the heat roller
section.
1)
3)
9) Remove the E-ring and remove the reverse gate.
3)
2)
1)
1)
2)
2)
FO-DC550 DISASSEMBLY AND ASSEMBLY 8 - 6
3)
6) Remove the C-ring and the fusing bearing, and remove the heat
roller.
5. Tray paper feed/transport section
A. List
1)
2)
3)
No.
1
2
3
4
5
Heat roller
Part name Ref.
Paper holding arm
PPD1 sensor PWB
LSU unit
Intermediate frame unit
Paper feed roller
B. Disassembly procedure
1) Remove the paper holding arm.
Remove the arm holder from the main unit, and remove the holder
from the arm.
1)
7) Remove the parts from the heat roller.
2)
Note: Apply grease to the sections specified with ∗1.
Grease: “JFE552” UKOG-0235FCZZ
2)
1
1
3)
2)
3)
2
4)
1)
Apply grease "GU-2" (UKOG-0255FCZZ)
to the fusing gear surface ∗2.
8) Remove two screws and remove the thermo unit.
2) Remove the two screws, and remove the hinge guide R.
3) Remove the fan duct and disconnect the connector. (2 positions)
4) Remove the six screws, and remove the scanner unit.
1)
5)
5)
6)
3)
5)
5)
5)
1)
2)
2)
4)
3)
4)
1)
5)
C. Assembly procedure
For assembly, reverse the disassembly procedure.
FO-DC550 DISASSEMBLY AND ASSEMBLY 8 - 7
5) Disconnect the connector from the MCU PWB.
9) Disengage the pawl, and remove the roller knob.
6) Disengage the pawls (2 positions), and remove the sensor PWB.
10) Disengage the pawl, and shift the pulley and the bearing.
3)
2)
3)
1)
4)
2)
11) Remove the paper exit roller, and remove the belt, the pulley, and
the bearing.
1)
2)
1)
7) Remove the screw, and open the upper paper guide.
1)
1)
2)
12) Remove the connector and the screw, and remove the speaker
unit.
3)
8) Remove the roller, and remove the belt.
2)
2)
1)
1)
FO-DC550 DISASSEMBLY AND ASSEMBLY 8 - 8
18) Remove the three screws, and remove the DUP motor unit and the
belt.
13) Remove the flat cable and the grounding wire.
14) Remove the four screws, and remove the FAX PWB unit.
2)
3)
3)
1)
1)
3)
2)
1)
4)
19) Remove the harness guide.
3)
3)
15) Disconnect the connectors.
16) Remove the three screws, and remove the MCU PWB.
1)
3)
2)
2)
2)
1)
20) Remove the five screws and the grounding wire, and remove the
main drive unit.
2)
1)
1)
17) Remove two screws and remove the toner motor.
1)
1)
1)
2)
1)
CAUTION:Attach the gears securely
FO-DC550 DISASSEMBLY AND ASSEMBLY 8 - 9
21) Remove the parts as shown below, and remove the pressure
release solenoid and the paper feed solenoid.
23) Remove two screws and remove the fusing connector.
24) Remove five screws and the connector, and lift the intermediate
frame unit to remove.
3)
3)
3)
3)
3)
4)
4)
2)
1)
2)
1)
4)
2)
2)
3)
1)
25) Remove the four screws, and remove the lower paper guide unit.
22) Remove each pawl, and remove the paper exit tray.
[Note for installation]
Fit the lower paper guide hole (a) with the shifter gear hole (b) so
that the black resin (c) of the shifter unit can be checked.
3)
c b
1)
1)
a
1)
1)
2)
1)
4)
2)
FO-DC550 DISASSEMBLY AND ASSEMBLY 8 - 10
26) Disengage the pawl, and remove the pulley.
31) Remove the four screws, and remove the LSU.
27) Shift and remove the shifter unit.
1)
1)
1)
3)
2)
4)
2)
3)
1)
28) Remove the screw, and remove the grounding plate and the gear.
29) Remove the E-ring, the gear, and the bearing, and remove the
shifter roller.
1)
Note: When assembling, turn it to the right and attach.
2)
3)
30) Put the lower paper guide unit upside down, remove the two
screws, and remove the shifter motor.
1)
2)
FO-DC550 DISASSEMBLY AND ASSEMBLY 8 - 11
32) Remove the screw and the E-ring, and remove the PS semi-circular earth plate and the PS roller unit.
36) Remove two E-rings and remove the paper feed roller.
37) Remove three E-rings and remove the clutch unit.
33) Remove the E-ring and remove the spring clutch from the PS roller
unit.
Back
5)
5)
Clutch unit
4)
4)
Paper feed
roller
PS roller unit
Use grease of
Floil FG40H
only to apply to
this section.
4)
4)
PS semi-circular
PS
semi-circuler
earth
plate
earth plate
1)
3)
2)
Front
1)
3)
34) Remove three screws and remove the TC front paper guide.
1)
2)
38) Remove the semi-circular roller unit.
2)
39) Remove the semi-circular rubber.
2)
35) Remove the screw and the connector, and remove the PPD1 sensor PWB.
1)
1)
1)
2)
C. Assembly procedure
For assembly, reverse the disassembly procedure.
FO-DC550 DISASSEMBLY AND ASSEMBLY 8 - 12
6. Manual paper feed section
3) Remove three screws and remove the multi paper feed upper
frame.
A. List
No.
1
2
3
4
1)
Part name Ref.
Manual transport roller
Cassette detection switch
PPD1 sensor PWB
Side door detection unit
1)
B. Disassembly procedure
Multi unit
1) Remove the screw and remove the multi upper cover.
1)
2)
2)
4) Remove two screws and remove the multi feed bracket unit from
the multi paper feed upper frame.
2)
1)
2) Remove the screw and remove the side door detection unit.
2)
2)
1)
Back
Wire treatment
FO-DC550 DISASSEMBLY AND ASSEMBLY 8 - 13
1)
5) Remove three E-rings and remove the manual paper feed roller
B9.
7) Cut the binding band and remove the multi paper feed solenoid.
1)
1)
1)
1)
3)
2)
Multi paper feed
solenoid
3)
2)
L O CK
T O
K
6) Remove the pick-up roller.
C. Assembly procedure
For assembly, reverse the disassembly procedure.
D. Pressure plate holder attachment
1)
1) Attach the pressure plate holder so that the resin section is not
covered with the seal M1-N.
Seal M1-N
Pressure plate
holder
2)
Attachment
reference
Attachment
reference
FO-DC550 DISASSEMBLY AND ASSEMBLY 8 - 14
7. Rear frame section
7) Remove two screws and one connector, and remove the exhaust
fan motor.
A. List
Note: Be careful of the installing directions of the fan.
Attach it so that the blowing direction faces outside.
No.
1
2
3
4
5
6
Part name Ref.
FAX PWB
Mirror motor
Main motor
Exhaust fan motor
NIC PWB
Main PWB
1)
B. Disassembly procedure
1) Remove the rear cabinet.
3)
2) Remove the connector, the flat cable, and the grounding wire.
3) Remove three screws, and remove the FAX PWB.
2)
1)
Blowing direction
8) Disconnect the connectors.
9) Remove the five screws, and remove the MCU PWB.
1)
2)
2)
1)
2)
3)
2)
2)
4) Disconnect the connector.
5) Remove two screws, and remove the scanner motor.
2)
1)
3)
1)
2)
3)
2)
1)
2)
2)
C. Assembly procedure
For assembly, reverse the disassembly procedure.
6) Remove two screws and one harness, and remove the main
motor.
3)
1)
2)
FO-DC550 DISASSEMBLY AND ASSEMBLY 8 - 15
8. Power section
C. Assembly procedure
For assembly, reverse the disassembly procedure.
A. List
10. Reverse roller section (RSPF model
only)
No.
Part name Ref.
1 Power PWB
A. List
B. Disassembly procedure
1) Disconnect each connector.
No.
Part name Ref.
1 Reverse roller
2) Remove the screw, and remove the earth line.
3) Remove two screws, and remove the power PWB unit.
B. Disassembly procedure
1) Remove four screws
2) Remove the spring, and the earth wire
3) Remove the reverse unit.
4)
1)
1)
1)
1)
2)
1)
3)
2
5)
4)
C. Assembly procedure
For assembly, reverse the disassembly procedure.
3
9. Duplex motor section (RSPF model only)
1
A. List
No.
Part name Ref.
1 Duplex motor
4) Bend the reverse roller and remove it.
B. Disassembly procedure
1) Remove the rear cabinet.
2) Remove two screws.
3) Remove the Duplex motor cover.
4) Remove the Duplex motor.
1
C. Assembly procedure
For assembly, reverse the disassembly procedure.
1
3
1
2
Note: When reassembling, be sure to engage the Duplex motor gear
with the belt on the main body side.
FO-DC550 DISASSEMBLY AND ASSEMBLY 8 - 16
11. RSPF section (RSPF model only)
C. Upper cover
1) Remove four screws from the bottom of the main body.
A. RSPF
2) Remove the upper cover.
(1) Remove the rear cabinet.
2
1) Remove four screws.
2) Remove the rear cabinet.
(2) Remove the RSPF.
1) Remove the connector and the cable.
2) Remove the RSPF.
1
1
1
D. Pickup unit
1) Remove the belt, the paper feed frame spring, and two harnesses.
2) Remove the pickup unit.
1
4)
3)
2)
1)
1
B. Intermediate tray
1)
2
Remove the intermediate tray.
1
1
1
Note: When reassembling, be careful of the hole position for the paper
feed frame spring.
FO-DC550 DISASSEMBLY AND ASSEMBLY 8 - 17
E. Upper cover of the pickup unit.
G. Pickup solenoid
1) Remove two screws from the bottom of the pickup unit.
1) Remove two screws.
2) Remove the upper cover.
2) Remove the pickup solenoid.
2
2
1
A
1
1
F. Sensor PWB
1) Remove two screws.
2) Remove the sensor PWB.
3) Remove the harness.
1
Note: When reassembling, hang the iron core on the solenoid arm.
1
3
H. Clutch
(1) Remove the clutch unit.
1) Remove the E-ring.
2
2) Remove the pulley and the bush.
3) Slide the bush in the arrow direction.
4) Lift the clutch pawl.
5) Remove the clutch unit.
2
1
5
3
FO-DC550 DISASSEMBLY AND ASSEMBLY 8 - 18
4
(2) Remove the clutch
(2) Remove the Manual paper feed roller, pickup roller.
1) Remove the E-ring.
1) Remove the parts.
2) Remove the parts.
2) Remove the manual paper feed roller.
3) Remove the pickup roller.
4) Remove the parts.
4
1
3
1
1
2
2
1
I. Manual paper feed roller, pickup roller
(1) Remove the pickup unit.
J. Transport unit removal
1) Lift the paper stopper.
1) Disconnect the connector, and cut the binding band.
2) Slide the take-up roller unit.
2) Remove two screws, and remove the document tray unit.
3) Slide the bushing in the arrow direction.
3) Remove five screws, and remove the transport unit.
4) Remove the take-up roller.
A
1
2
1
5
5
3
2
4
5
5
4
3
3
6
Note: When reassembling, hang the convex portion of the roller unit
on the solenoid arm.
FO-DC550 DISASSEMBLY AND ASSEMBLY 8 - 19
K. Belt 1
N. Solenoid
1) Remove the belt.
1) Remove the harness.
2) Remove two screws.
3) Remove the solenoid.
3
1
2
O. Clutch
1
1) Cut the band with nippers.
2) Remove the harness.
3) Remove the clutch.
L. Belt 2
1) Remove three screws.
2) Remove the drive unit.
3) Remove the belt.
1
2
3
1
3
2
1
1
Note: When reassembling, hang the belt on the boss.
M. SPF motor
1) Remove the harness.
2) Remove two screws.
3) Remove the SPF motor.
3
1
2
FO-DC550 DISASSEMBLY AND ASSEMBLY 8 - 20
P. Paper supply roller
Q. Paper entry sensor
(1) Remove the parts.
1) Loosen the screw.
1) Remove the two screws.
2) Open the paper exit paper guide.
2) Remove the parts.
3) Remove the paper entry sensor.
4) Remove the harness.
1
1
2
4
3
(2) Remove the paper supply roller.
1) Loosen the screw.
2) Open the paper exit paper guide.
3) Remove the parts.
4) Remove the paper supply roller.
1
2
1
2
R. Transport roller 1.
(1) Remove the parts.
1) Remove the parts.
1
3
1
4
1
3
FO-DC550 DISASSEMBLY AND ASSEMBLY 8 - 21
(2) Remove the parts.
S. Paper exit roller
1) Loosen the screw.
(1) Remove the parts.
2) Open the paper exit paper guide.
1) Remove two screws.
3) Remove the parts.
2) Remove the parts.
1
2
3
1
1
2
(2) Remove the paper feed paper guide upper.
1) Remove two screws.
2) Remove the paper feed paper guide upper.
(3) Remove the transport roller.
1) Remove the paper exit paper guide.
2
2) Remove the transport roller.
2
1
1
FO-DC550 DISASSEMBLY AND ASSEMBLY 8 - 22
(3) Remove the paper exit roller.
(2) Remove the solenoid.
1) Remove the parts.
1) Remove the screw.
2) Remove the paper exit roller.
2) Remove the solenoid.
1
2
1
1
2
T. Solenoid
(1) Remove the reverse gate
1) Remove the ring
2) Remove the reverse gate
1
2
Note: When reassembling, be careful of the groove and the hole
positions of the spring.
Note: When reassembling, hang 2) on the solenoid.
FO-DC550 DISASSEMBLY AND ASSEMBLY 8 - 23
[9] ADJUSTMENTS
5) Calculate the main scanning direction magnification ratio.
Main scanning direction magnification ratio
1. Optical section
=
Copy image dimensions
Original dimension
X 100 (%)
A. Copy magnification ratio adjustment
The copy magnification ratio must be adjusted in the main scanning
direction and in the sub scanning direction. To adjust, use TC 48-01.
(When a 100mm scale is used as the original.)
mm
1/2mm
10
20
Original (Scale)
100
110
120
JAPAN
HARDENED
STAINLESS
130
140
(1) Outline
150
Shizuoka
The main scanning (front/rear) direction magnification ratio adjustment
is made manually.
The adjustment is made by manual key operations. (The zoom data
register set value is changed for adjustment.)
Paper feed
direction
mm
1/2mm
10
20
100
110
HARDENED
STAINLESS
JAPAN
120
130
140
150
Shizuoka
Reference
The magnification ratio in the sub scanning direction is adjusted by
changing the carriage (scanner) scanning speed.
Comparison point
Copy
110
(2) Main scanning/sub scanning direction magnification
ratio adjustment
6) Check that the copy magnification ratio is within the specified
range. If it is not within the specified range, perform the following
procedures.
a. Cases when the adjustment is required
1) When the main PWB is replaced.
2) When the EEPROM in the main PWB is replaced.
7) Execute TC 48-01 to select the main scanning direction copy
magnification ratio adjustment mode.
To select the adjustment mode, use the [←/→] key.
3) When "U2" trouble occurs.
4) When repairing or replacing the optical section.
b. Necessary tools
Mode
• Scale
c. Main scanning direction adjustment procedure
1) Set the scale vertically on the document table. (Use a long scale
for precise adjustment.)
Main scan direction
magnification ratio
OC mode sub scan
direction magnification ratio
Display
item
F-R
Default
value
50
PRINT mode lamp
SCAN
50
SCAN mode lamp
LED
8) Enter the new set value of main scanning direction copy
magnification ratio with the copy quantity set key, and press the
[START] key.
9) Change the set value and repeat the adjustment until the ratio is
within the specified range.
When the set value is changed by 1, the magnification ratio is
changed by 0.1%.
d. Sub scanning direction adjustment procedure
1) Set the scale on the document table as shown below. (Use a long
scale for precise adjustment.)
2) Set the copy magnification ratio to 100%.
3) Make a copy on A4 or 81/2" x 11" paper.
4) Measure the length of the copied scale image.
FO-DC550 ADJUSTMENTS 9 - 1
2) Set the copy magnification ratio to 100%.
Mode
3) Make a copy on A4 or 81/2" x 11" paper.
Print center offset
(Main cassette paper
feed)
(*) Print center offset
(2nd cassette paper
feed)
Print center offset
(Manual paper feed)
2nd print center
offset (Main cassette
paper feed)
4) Measure the length of the copied scale image.
5) Calculate the sub scanning direction copy magnification ratio
using the formula below.
Copy image dimensions
Original dimension
=
X 100 (%)
110
Original (Scale)
mm
1/2mm
10
20
100
110
120
130
140
10
20
100
110
120
JAPAN
Paper feed
direction
HARDDENCD
STAINLESS
130
140
50
COPY mode lamp
2nd cassette lamp
MFT
50
SIDE2
50
COPY mode lamp
Manual feed lamp
PRINT mode lamp
Main cassette lamp
50-10
(*): Support for the installation models. For non-installation models,
skip.
150
Shizuoka
mm
1/2mm
TRAY2
TC
The modes can be selected by pressing [←/→] key.
HARDDENCD
STAINLESS
JAPAN
Display
Default
LED
item
TRAY1
50
COPY mode lamp
Main cassette lamp
150
* In the 2nd print center offset adjustment, print is made forcibly as
1to2/Long Edge from OC regardless of duplex setting.
(1) Lead edge adjustment
Shizuoka
Reference
Comparison point
1) Set a scale to the center of the paper lead edge guide as shown
below, and cover it with B4 or 8 1/2" x 14" paper.
Copy
6) Check that the actual copy magnification ratio is within the
specified range. (100 ± 1.0%).
If it is not within the specified range, perform the following
procedures.
7) Execute TC 48-01 to select the sub scanning direction copy
magnification ratio adjustment mode.
To select the adjustment mode, use the [←/→] key. (SCAN mode
lamp ON)
8) Enter the new set value of sub scanning direction copy
magnification ratio with the copy quantity set key, and press the
[START] key.
Repeat procedures 1) - 8) until the sub scanning direction actual copy
magnification ratio in 100% copying is within the specified range.
When the set value is changed by 1, the magnification ration is
changed by 0.1%.
B. Image position adjustment
The employed test commands and the contents are as follows:
Mode
Print start position
(Main cassette paper
feed)
(*) Print start position
(2nd cassette paper
feed)
Print start position
(Manual paper feed)
Image lead edge void
amount
Image scan start
position
Image rear edge void
amount
Display
Default
LED
item
TRAY1
50
COPY mode lamp
Main cassette
lamp
TRAY2
50
COPY mode lamp
2nd cassette lamp
2) Execute TC 50 - 01
TC
MFT
50
DEN-A
50
COPY mode lamp
Manual feed lamp 50-01
PRINT mode lamp
RRC-A
50
SCAN mode lamp
DEN-B
50
COPY mode lamp
PRINT mode lamp
SCAN mode lamp
3) Set the print start position (A: COPY mode lamp ON), the lead
edge void amount (B: PRINT mode lamp ON), the scan start position (C: SCAN mode lamp) to 1, and make a copy of the scale at
100%.
4) Measure the image loss (Rmm) of the scale.
Set C = 10 x R (mm). (Example: Set to 40.)
When the value of C is increased by 10, the image loss is
decreased by 1mm. (Default: 50)
5) Measure the distance (Hmm) from the paper lead edge to the
image print start position.
Set A = 10 x H (mm). (Example: Set to 50.)
When the value of A is increased by 10, the image lead edge is
moved to the paper lead edge by 1mm. (Default: 50).
6) Set the lead edge void amount to B = 50 (2.5mm). (Default: 50)
When the value of B is increased by 10, the void is extended by
about 0.1mm. (For 25 or less, however, the void amount is
regarded as 0.)
* The SFP adjustment is made by adjusting the SPF image scan start
position after OC adjustment.
FO-DC550 ADJUSTMENTS 9 - 2
(Example)
Document guide
Distance from the paper lead edge
to the image lead edge, H = 5mm
Image loss, R = 4mm
5mm
10mm
2) Execute TC 50-10 to select the print center offset (cassette paper
feed) adjustment mode.
The set adjustment value is displayed on the copy quantity display.
3) Make a copy and check that the copied center line is properly
positioned.
The standard value is 0 ±2mm from the paper center.
(2) Image rear edge void amount adjustment
1) Set a scale to the rear edge section of A4 or 11" x 8 1/2" paper size
as shown in the figure below, and cover it with B4 or 8 1/2" x 14"
paper.
2.0mm or less
(Copy A)
Copy image
B4 or 8 1/2″ × 14″ paper
Shift
A4 size rear edge
Copy paper
folding line
2.0mm or less
(Copy B)
Copy image
Shift
Copy paper
folding line
(Paper feed direction)
2) Execute TC 50 - 01 to select the image rear edge void amount
adjustment mode.
The set adjustment value is displayed on the copy quantity display.
3) Make a copy and measure the void amount of image rear edge.
Void amount (Standard value: 2 - 3mm)
4) If the measured value is out of the specified range, change the set
value and repeat the adjustment procedure.
When the set value is increased by 1, the copy image is shifted by
0.1mm toward the rear frame.
• For the manual paper feed, change the manual paper feed
adjustment mode and perform the similar procedures.
• Since the document center offset is automatically adjusted by the
CCD which scan the reference lines (F/R) on the back of document
guide, there is no need to adjust manually.
Scale image
2. Copy density adjustment
Paper rear edge
A. Copy density adjustment timing
The copy density adjustment must be performed in the following cases:
• When maintenance is performed.
4) If the measurement value is out of the specified range, change the
set value and repeat the adjustment procedure.
The default value is 50.
• When the developing bias/grid bias voltage is adjusted.
(3) Center offset adjustment
• When the optical section is disassembled.
1) Set the self-made test chart for the center position adjustment so
that its center line is aligned with the center mark of the document
guide.
• When the OPC drum is replaced.
• Test chart for the center position adjustment.
Draw a line at the center of A4 or 8 1/2" x 11" paper in the paper
transport direction.
• When the memory trouble (U2) occurs.
• When the optical section is cleaned.
• When a part in the optical section is replaced.
• When the main control PWB is replaced.
• When the EEPROM on the main control PWB is replaced.
B. Note for copy density adjustment
1) Arrangement before execution of the copy density adjustment
• Clean the optical section.
• Clean or replace the charger wire.
• Check that the voltage at the high voltage section and the
developing bias voltage are in the specified range.
FO-DC550 ADJUSTMENTS 9 - 3
C. Necessary tool for copy density adjustment
(2) Perform the adjustment in each mode.
• One of the following test charts:
UKOG-0162FCZZ, UKOG-0089CSZZ, KODAK GRAY SCALE
1) Execute TC 46-01 (300dpi). To adjust in 600dpi, execute TC 4602.
• B4 (14" x 8 1/2") white paper
2) Select the mode to be adjusted with the exposure mode select key.
Set the exposure level to 3 (center) for all adjustment. (Except for
the auto mode.)
• The user program AE setting should be "3."
1
2
3
4
5
6
7
8
9
10
W
TEXT
(1) Exposure mode, level display
| | | | |
Test chart comparison table
UKOG0162FCZZ
DENSITY
No.
1
UKOG0089CSZZ
DENSITY
No.
0.1
(2) Mode select key
2
3
4
5
6
7
8
9
10
W
Adjustment
mode
Display
item
Sharp gray chart
adjustment level
LED
Auto mode
AE
COPY mode lamp
"3" is slightly
copied.
Text mode
TEXT
PRINT mode lamp
"3" is slightly
copied.
Photo mode
PHOTO SCAN mode lamp
"3" is slightly
copied.
D. Features of copy density adjustment
Text T/S mode
TSTXT
For the copy density adjustment, the image data shift function provided
in the image process LSI is used.
PRINT mode lamp
SCAN mode lamp
"3" is slightly
copied.
Auto T/S mode
TSAE
COPY mode lamp
SCAN mode lamp
"3" is slightly
copied.
KODAK
GRAY
SCALE
0.2
1
0.3
2
0.5 1.9
3
4
19
0
A
List of the adjustment modes
Auto Mode
Manual Mode
Photo Mode
Manual T/S
mode
T/S Auto mode
Brightness 1 step only
Brightness 5 steps. Adjustment of only the center
brightness is made.
Brightness 5 steps. Adjustment of only the center
brightness is made.
Brightness 5 steps. Adjustment of only the center
brightness is made.
Brightness 1 step only
3) Make a copy.
Check the adjustment level (shown in the above table) of the
exposure test chart (Sharp Gray Scale).
Sharp Gray Scale adjustment level
Non toner
save mode
1
2
3
4
5
6
7
8
9
10
W
6
7
8
9
10
W
Slightly copied.
E. Copy density adjustment procedure
Not copied.
The copy density can be adjusted in 300dpi or in 600dpi.
Main code
46
Sub code
01
02
Resolution for copy density adjustment
300dpi
600dpi
Toner save
mode
1
2
For selection of modes, use the copy mode select key.
3
4
5
Slightly copied.
(1) Test chart (UKOG-0162FCZZ) setting
Not copied.
1) Place the test chart so that its edge is aligned with the A4 (Letter)
reference line on the document table. Then place a A4 (14" x
8 1/2") white paper on the test chart and close the document cover.
(When too bright): Decrease the value displayed on the copy quantity
display.
(When too dark):
Increase the value displayed on the copy quantity
display.
* The value can be set in the range of 1 - 99.
White paper
Test chart
FO-DC550 ADJUSTMENTS 9 - 4
3. High voltage adjustment
4. Duplex adjustment
A. Main charger (Grid bias)
A. Adjusting the paper reverse position in memory
for duplex copying
Note:
• Use a digital multi meter with internal resistance of 10MΩ or more
measurement.
• After adjusting the grid LOW output, adjust the HIGH output. Do not
reverse the sequence.
Procedures
1) Set the digital multi meter range to DC700V.
2) Set the positive side of the test rod to the connector CN11-3
(GRID) of high voltage section of the power PWB and set the
negative side to the frame ground (power frame).
3) Execute TC 8-02. (The main charger output is supplied for 30 sec
in the grid voltage HIGH output mode.)
4) Adjust the control volume (VRG1) so that the output voltage is 580
±12V.
This step adjusts the front surface printing (odd-number pages of a
document set) in the S-D mode copying and the leading edge position
of an image on even-number pages in the D-S mode.
That is, it covers the adjustment of the second surface printing mode
(image loss at the front edge of an image) in which image data is once
stored in memory.
The image data is read, starting from its front end in the document
delivery direction (Reference direction of document setting in the OC
mode)and stored in memory.
This stored image data is printed starting at the printing start position,
in the order of last-stored data to the first-stored data.
In other words, the front edge image loss of the image can be adjusted
by changing the document read end position.
(Adjustment procedure)
1) Preparing test chart (Draw a scale at the rear end of one side of a
sheet of A4 white paper or letter paper)
5 10
VRG1
2) Set the test chart so that the scale is positioned as shown below, in
the S-D mode and the D-S mode.
Scale (S-D mode)
Scale (D-S mode)
B. DV bias check
Note: • A digital multi meter with internal resistance of 1GΩ must be
use for correct check.
• The adjustment volume is locked, and no adjustment can be
made.
Procedures
3) Execute test command 50-18.
1) Set the digital multi meter range to DC500V.
2) Set the positive side of the test rod to the connector CN-10-1 (DV
BIAS) and set the negative side to the frame ground (power
frame).
3) Execute TC 25-01 to output the developing bias for 30sec, and
check that the output is –400±8V.
Mode
OC memory reverse
output position
SPF memory reverse
output position
Display
item
OC
Default
SPF
LED
50
COPY mode lamp
50
PRINT mode lamp
Select the SPF memory reverse output position, and press
[START] key to make a copy.
VRDV
Adjust the setting so that the front edge image loss is less than 4.0
mm in the R-SPF mode.
An increase of 1 in setting represents an increase of 0.1 mm in
image loss.
Front edge of paper
The front edge of the
scale on test chart
less than 4 mm
FO-DC550 ADJUSTMENTS 9 - 5
Void area
5 10
2) Set the test chart on the document glass as shown below.
Document guide
The trailing edge has a scale
2nd printing surface where scale is printed (lower side)
Table glass
B. Adjusting trailing edge void in duplex copy mode
This is the adjustment of the first surface printing mode (rear end void)
in duplex copying.
In a duplex copying operation, the paper is delivered starting from the
rear end of the first printing surface. It is therefore necessary to make a
void area at the rear end on the first printing surface to prevent paper
jam at the fusing part.
3) Execute test command 50-19 to turn on the PRINT mode lamp and
make the printing mode in OC-D mode.
Make a copy of the test chart to check the void area of the scale on
the image.
Void position to be check
There are two adjustment modes:
1) Image cut rear end void quantity (R-SPF) 50-19 (SCAN mode
lamp)
The size (length) of a document read from the R-SPF is detected,
the image at the trailing edge of the first printing surface is cut to
make a void area. (The adjustment of void quantity at the time
when the cassette paper size is not recognized.)
Paper
2) Paper trailing edge void quantity 50-19 (PRINT mode lamp)
This adjustment is made when the cassette paper size is
recognized. The trailing edge void quantity can be adjusted by
changing the trailing edge image laser OFF timing.
The paper void quantity should be first adjusted before the image cut
trailing edge void quantity (R-SPF) is adjusted.
The adjustment modes can be selected by pressing [←/→] key.
(Adjustment range; 1 – 99)
Enter the adjustment value and press [START] key to save the set
value and make a copy. (The paper information is cleared for every
copy.)
When the set value is increased by 1, the void amount is increased by
about 0.1mm.
Mode
Paper rear edge void
amount
Print start position (Duplex
back surface)
Display
item
DEN-B
Default
LED
50
PRINT mode lamp
50
SCAN mode lamp
RRC-D
The trailing edge void on the first printing surface
is shown above.
Adjust the setting so that the void area is 4 - 5 mm. An increase in 1 of
setting represents 0.1 mm in void area.
(2) Image cut trailing edge void quantity (R-SPF)
1) Set the test chart so that the scale is positioned as shown below.
Scale (D-D mode)
* The initial value of duplex setting is 2to2.
(Adjustment procedure)
2) Execute test command 50-19 to turn on the SCAN mode lamp(on
the operation panel) and make the printing mode in the D-D mode.
(1) Paper trailing edge void quantity
1) Preparing test chart (Draw a scale at the rear end of one side of a
sheet of A/4 white paper or letter paper)
3) Remove and reinsert the cassette.
Note: Make sure to carry out this step before making a copy during
this adjustment.
4) Make a copy and check the void area of the scale on the image.
Adjust the setting so that the void area is 2 - 4 mm. An increase of
1 in setting represents an increase of 0.1 mm in void area.
l Void position to be checked
FO-DC550 ADJUSTMENTS 9 - 6
5. SPF (RSPF) scan position automatic
adjustment
The size of the black chart (UKOG-0011QSZZ) is 297 x 420. Divide it
into four for use.
Place a black chart so that it covers the SPF scan glass and the OC
glass together, and close the OC cover.
When test command 53-08 is executed, the current adjustment value
is displayed as the initial display.
* Default is 1. Adjustment range is 1 – 99. Adjustment unit 1 = about
0.127mm
* If the values are kept as the default values, SPF scan is not performed properly. The front area of the proper scan position may be
scanned.
In case of AUTO, press [START] key, and the mirror unit scans from
the home position to the SPF scan position with the adjustment value
displayed. The SPF glass cover edge position is calculated from the
difference between the SPFG glass cover edge and the OC side
document glass CCD output level. If the adjustment is normal, the
adjusted value is displayed. If abnormal, the error LED lights up with
the current set value displayed.
6. RSPF (SPF) mode sub scanning direction
magnification ratio adjustment
Note: Before performing this adjustment, be sure to check that the OC
mode adjustment in copying has been completed.
1) Put a scale on the original table as shown below, and make a
normal copy (100%) on the front and the back surfaces to make a
test chart.
During the error LED is lighted, when [START] key is pressed again,
execution is performed again.
Mode
SPF scan position auto
adjustment
SPF scan position manual
adjustment
Display
item
AUTO
MANU
Default
LED
1
COPY mode lamp
1
PRINT mode lamp
Operation
The operation is similar to test command 46-01. (In MANUAL)
OK/ERR display in AUTO
<When OK>
53-08 SPF AUTO
AUTO 100% **
<When ERR>
OK
53-08 SPF AUTO
AUTO 100% **
Note: Since the printed copy is used as a test chart, put the scale in
parallel with the edge lines.
2) Set the test chart on the RSPF and make a duplex copy (D-D or DS) in the normal ratio (100%).
ERR
3) Compare the scale image and the actual image.
If necessary, perform the following adjustment procedures.
4) Execute TC 48-05.
5) The current front surface sub scanning direction magnification ratio
correction value is displayed in two digits on the display section.
To select SIDE1 and SIDE2, use [←/→] keys.
6) Enter the set value and press the start key.
When adjusting the RSPF, use [2-SIDED COPY] key to select
single/duplex after entering the one page print mode, performing 2page single copy.
Mode
Sub scan magnification ratio
adjustment on the surface of SPF/
RSPF document
Sub scan magnification ratio
adjustment on the surface of
RSPF document
Display
item
SIDE1
SIDE2
Default
LED
50
COPY
mode lamp
50
PRINT
mode lamp
* When there is no document in SPF, copy is inhibited.
<Adjustment specification>
6cm or more is required.
* Use a black chart (UKOG-0011QSZZ) or prepare a chart as shown
below.
Chart size: 300 x 100, prepared with cutting sheet No. 791 (Black) or
an equivalent one.
Adjustment
mode
Sub scanning
direction
magnification
ratio (SPF/RSPF
mode)
Reason: To prevent erroneous detection by disturbing light of a
fluorescent lamp, etc.
FO-DC550 ADJUSTMENTS 9 - 7
Spec value
TC
Set value
At normal:
±1.0%
48-5
Add 1:
0.1% increase
Reduce 1: 0.1%
decrease
Setting
range
1 – 99
7. Automatic black level correction
a. Cases when the adjustment is required
1) When the main PWB is replaced.
2) When the EEPROM in the main PWB is replaced.
3) When "U2" trouble occurs.
4) When repairing or replacing the optical section.
b. Adjustment procedure
Used to acquire the black level target value used for the black level
adjustment of white balance.
When test command 63-02 is executed, the current correction value is
displayed in 3 digits of 12bit hexadecimal number.
Place the gray gradation chart (UKOG-0162FCZZ) used as the
correction document so that the density 10 (black side) comes on the
left side and that the chart is upside down at the center of the plate left
center.
10
Chart back surface
When [ENTER/START] key is pressed, the mirror base unit scans the
chart and calculates the correction value.
After completion of correction, the corrected value is displayed on the
LCD.
* Default: 0
* If the value is set to the default, operation is made with 0x60.
c. Operation
1) Initial display
63-02 BLACK LEVEL
0
2) [ENTER/START] Correction start
63-02 BLACK LEVEL
EXECUTING...
<During canceling - When C/CA is pressed->
After canceling, the machine goes into the sub code entry standby
mode.
THE JOB IS BEING
CANCELED.
3) After execution
63-02 BLACK LEVEL
*** OK
3) In case of an error
63-02 BLACK LEVEL
*** ERR
FO-DC550 ADJUSTMENTS 9 - 8
[10] TEST COMMAND, FAX SOFT SWITCH, TROUBLE CODES
1. Entering the test command mode
To enter the serviceman test command mode, press the keys as follows:
[#] key → [∗] key → [C] key → [∗] key
[MENU] key → [9] key → [∗] key → [8] key → [#] key → [7] key
To cancel the test command mode, press the [CA] key.
2. Key rule
[10KEY]:
Entry of MAIN CODE/SUB CODE
Selection of an item
Setup of an adjustment value in case of test commands for adjustment
[←/→]:
Selection of MAIN CODE/SUB CODE
Selection of an item
[ENTER/START]: Settlement
<In case of test commands for print>
[ENTER]: Settlement (Without print)
[START]:
Settlement/Print
[C]:
(Interrupting operation check) Returns to the upper hierarchy.
In case of test command of operation check, terminates the operations.
[CA]:
Exits from the test command mode.
For a test command of adjustment, the display returns to the initial display (00-00).
3. List of test commands
Main
code
Sub
code
1
01
2
Contents
Mirror scan (SCAN CHK)
02
Mirror home position sensor (MHPS) status display
(MHP-SENSOR)
06
Mirror scan aging (SCAN AGING)
01
Single Paper Feeder (SPF) aging (SPF AGING)
02
SPF sensor status display (SPF SENSOR)
03
SPF motor operation check (SPF MOTOR CHK)
06
RSPF resist clutch operation check (RSPF RES.CHK)
08
SPF paper feed solenoid operation check (SPF SPUS
CHK)
Main
code
Sub
code
9
01
Duplex motor normal rotation check (DPLX ROT.)
02
Duplex motor reverse rotation check (DPLX
ROT.REV.)
04
Duplex motor rotating speed adjustment (DPLX
ROT.SPEED)
10
00
Toner motor operation (TONER MOTOR)
14
00
Cancel of trouble other than U2 (TRBL CANC.)
16
00
U2 trouble cancel (U2 TRBL CANC.)
22
04
JAM total counter display (JAM TTL CNT)
Contents
05
Total counter display (TTL CNT)
SPF counter display (SPF CNT)
11
FAX-related counter display
09
RSPF reverse solenoid operation check (RSPF SPFS
CHK)
08
10
RSPF paper exit gate solenoid operation check
(RSPF SGS CHK)
12
Drum counter display (DRUM CNT)
13
CRUM type display (CRUM TYPE)
ROM version display (ROM VER.)
3
03
Shifter operation check (SHIFTER CHK)
14
5
01
Operation panel display check (LCD/LED CHK)
16
Duplex counter display (DPLX CNT)
02
Fusing lamp, cooling fan operation check (HT LAMP
CHK)
17
Copy counter display (COPIES CNT)
18
Printer counter display (PRT.CNT)
03
Copy lamp ON check
(C-LAMP CHK)
19
Scanner mode counter display (S-MODE CNT)
21
Scanner counter display (SCAN CNT)
6
01
22
SPF JAM counter display (S JAM CNT)
01
JAM total counter clear (JAM TTL CLR.)
04
SPF counter clear (SPF CLR.)
Check of warm-up display and aging with JAM (WUP/AGING)
05
Duplex counter clear (DPLX CLR.)
07
Drum counter clear (DRUM CLR.)
Interval aging (INTERVAL AGING)
08
Copy counter clear (COPIES CLR.)
08
Shift to copy with warm-up display (W-UP C-MODE)
09
Printer counter clear (PRT.CLR.)
01
Developing bias output (DVLP BIAS SET.)
10
FAX counter clear (FAX CLR.)
02
Main charger output (Grid HIGH) (MHV(H) SET.)
13
Scanner counter clear (SCAN CLR.)
03
Main charger output (Grid LOW) (MHV(L) SET.)
14
SPF JAM total counter clear (S JAM TTL CLR.)
06
Transfer charger output (THV SET.)
02
7
01
06
8
Paper feed solenoid (CPFS1, CPFS2, MPFS)
operation check (PSOL CHK)
Resist roller solenoid (RRS) operation check (RES.R
SOL CHK)
24
25
15
Scanner mode counter clear (S-MODE CLR.)
01
Main motor operation check (MAIN MOTOR CHK)
10
Polygon motor operation check (LSU CHK)
FO-DC550 TEST COMMAND, FAX SOFT SWITCH, TROUBLE CODES 10 - 1
Main
code
Sub
code
26
02
(R)SPF setting (SPF/RSPF)
03
Second cassette setting (2ND TRAY)
30
Contents
04
Main unit duplex setting (DPLX)
06
Destination setting (DESTINATION)
07
Machine conditions check (CPM)
20
Rear edge void setting (END EDGE)
30
CE mark support control ON/OFF (CE MARK)
38
Cancel of stop at drum life over (DRUM LIFE END)
39
Memory capacity check (MEM.CHK)
40
Polygon motor OFF time setting (Time required from
completion of printing to turning OFF the motor) (LSU
MOTOR OFF)
42
Transfer ON timing control setting (TC ON TIMING)
43
Side void amount setting (SIDE VOID)
62
Energy-save mode copy lamp setting (C-LAMP E-S)
01
Paper sensor status display (P-SENSOR)
41
06
OC cover float detection level (OC FLOAT LEVEL)
43
01
Fusing temperature setting (Normal copy) (FU TEMP)
04
Fusing temperature setting in multi coy (FU TEMP
MULTI)
05
Fusing temperature setting in duplex copy (FU TEMP
DPLX)
09
Postcard size paper fusing control setting (FU CTR PCARD) (Japan model only)
11
Postcard size paper fusing temperature setting (FU
TEMP P-CARD) (Japan model only)
46
48
14
Fusing start temperature setting (FU TEMP START)
01
Copy density adjustment (300dpi) (EXP.LEVEL 300)
02
Copy density adjustment (600dpi) (EXP.LEVEL 600)
12
Density adjustment in the FAX mode (Collective
adjustment)
13
FAX mode density adjustment (normal text)
14
FAX mode density adjustment (Fine text)
15
FAX mode density adjustment (Super fine)
18
Image contrast adjustment (300dpi) (GAMMA 300)
19
Exposure mode setting (AE MODE)
20
SPF exposure correction (EXP.LEVEL SPF)
29
Image contrast adjustment (600dpi) (GAMMA 600)
30
AE limit adjustment (AE LIMIT)
31
Image sharpness adjustment (SHARPNESS)
32
Copier color reproduction setting (COLOR
REAPPEAR)
39
FAX mode sharpness adjustment
01
Mains can/sub scan direction magnification ratio
(COPY MAG.)
05
SPF/RSPF mode sub scan direction magnification
ratio in copying (SPF/RSPF MAG.)
Main
code
49
50
Sub
code
01
01
06
10
12
18
19
51
53
61
63
64
66
02
08
03
01
02
01
01
02
03
04
05
07
10
11
12
13
17
18
21
24
30
32
33
34
37
38
41
70
Contents
Download mode (DOWNLOAD MODE)
Lead edge image position (LEAD EDGE)
Copy lead edge position adjustment (SPF/RSPF)
(SPF/RSPF EDGE)
Print center offset adjustment (PRT.OFF-CENTER)
Document feed off-center adjustment (ORG.OFFCENTER)
Memory reverse position adjustment in duplex copy
(DPLX REVERSE)
Duplex copy rear edge void adjustment (DPLX END
EDGE)
Resist amount adjustment (RESIST ADJ.)
SPF scan position automatic adjustment (SPF AUTO)
HSYNC output check (LSU CHK)
Shading check (SHADING CHK)
Black level automatic correction (BLACK LEVEL)
Self print (1by2 mode) (SELF PRT.)
FAX soft SW setting
FAX soft SW initializing (excluding the adjustment
values)
FAX PWB memory check
Signal send mode (Max. value)
Signal send mode (Soft SW set value)
Image memory content print
Image memory content clear
300bps signal send (Max. value)
300bps signal send (Soft SW set value)
Dial test
DTMF signal send (Max. value)
DTMF signal send (Soft SW set value)
FAX information print
FAST SRAM clear
TEL/LIU status change check
Receive data check
Signal detection check
Communication time measurement
Speaker sound volume setting
Time setting/check
CI signal check
Print hold passcode check
FO-DC550 TEST COMMAND, FAX SOFT SWITCH, TROUBLE CODES 10 - 2
4. Descriptions of various test commands
Main
code
1
Sub
code
01
Contents
Mirror scan (SCAN CHK)
Details of function/operation
[Function]
When [ENTER/START] key is pressed, the home position is checked and the mirror base performs
full scan at the speed of the set magnification ratio.
During operation, the set magnification ratio is displayed.
The mirror home position sensor status is displayed with the “COPY mode lamp”. (When the mirror is
in the home position, the lamp lights up.)
During operation, the copy lamp lights up.
When [C] key is pressed, if the operation is on the way, it is terminated and the machine goes to the
sub code entry standby mode.
[Operation]
1) Initial display
01-01 SCAN CHK
- 100% +
2) [ZOOM]
01-01 SCAN CHK
- 78% +
02
Mirror home position sensor
(MHPS) status display
(MHP-SENSOR)
2) [←]
01-01 SCAN CHK
- 99% +
3) [ENTER/START]
01-01 SCAN CHK
EXECUTING... -
78% +
2) [→]
01-01 SCAN CHK
- 101% +
[Function]
Monitors the mirror home position sensor, and makes the "COPY mode lamp" turn on during the sensor ON status.
[Operation]
1) Initial display
01-02 MHP-SENSOR
EXECUTING...
06
Mirror scan aging (SCAN
AGING)
[Function]
When [ENTER/START] key is pressed, the mirror base performs full scan at the speed of the set
magnification ratio.
During operation, the set magnification ratio is displayed.
After 3sec, the mirror base performs full scan again.
∗ When [ENTER/START] key is pressed once, the ready lamp remains OFF.
The mirror home position sensor status is displayed on the "COPY mode lamp." (The lamp is ON
when the mirror is in the home position.)
During aging, the copy lamp is ON.
2
01
Single Paper Feeder (SPF)
aging (SPF AGING)
[Operation]
The operation is similar to test command 1-01.
[Function]
When [ENTER/START] key is pressed, the set magnification ratio is acquired and single-face document transport is performed in the case of SPF or duplex document transport in the case of R-SPF.
However, the operating conditions don't matter and the operation is not stopped even in case of a
jam. Also the magnification ratio is displayed on the LCD.
02
SPF sensor status display
(SPF SENSOR)
[Operation]
The operation is similar to test command 1-01.
[Function]
The ON/OFF status of the SPF sensors can be checked with the LCD.
When a sensor is ON, the sensor name is displayed on the LCD.
Sensor
Document set sensor
SPF document transport sensor
SPF paper feed cover open/close sensor
Display item
SPID
SPPD
SDSW
[Operation]
1) Initial display
02-02 SPF SENSOR
03
SPF motor operation check
(SPF MOTOR CHK)
2) When the sensor is ON:
02-02 SPF SENSOR
SPID SPPD SDSW
[Function]
When [ENTER/START] key is pressed, the motor rotates for 10sec at the speed corresponding to the
set magnification ratio.
[Operation]
The operation is similar to test command 1-01.
FO-DC550 TEST COMMAND, FAX SOFT SWITCH, TROUBLE CODES 10 - 3
Main
code
2
Sub
code
06
Contents
Details of function/operation
RSPF resist clutch operation
check (RSPF RES.CHK)
[Function]
When [ENTER/START] key is pressed, the RSPF resist clutch (SRRC) repeats ON for 500ms and
OFF for 500ms 20 times.
[Operation]
1) Initial display
02-06 RSPF RES.CHK
EXECUTING...
08
SPF paper feed solenoid
operation check (SPF SPUS
CHK)
[Function]
The SPF paper feed solenoid (SPUS) repeats ON for 500ms and OFF for 500ms 20 times by the use
of the solenoid drive control Bios.
[Operation]
1) Initial display
02-08 SPF SPUS CHK
EXECUTING...
09
RSPF reverse solenoid
operation check (RSPF
SPFS CHK)
[Function]
The SPF reverse solenoid (SPFS) repeats ON for 500ms and OFF for 500ms 20 times by the use of
the solenoid drive control Bios.
[Operation]
1) Initial display
02-09 RSPF SPFS CHK
EXECUTING...
10
RSPF paper exit gate
solenoid operation check
(RSPF SGS CHK)
[Function]
The SPF paper exit gate solenoid (SGS) repeats ON for 500ms and OFF for 500ms 20 times by the
use of the solenoid drive control Bios.
[Operation]
1) Initial display
02-10 RSPF SGS CHK
EXECUTING...
3
03
Shifter operation check
(SHIFTER CHK)
[Function]
The shifter is moved back and forth in four reciprocations.
[Operation]
1) Initial display
03-03 SHIFTER CHK
EXECUTING...
FO-DC550 TEST COMMAND, FAX SOFT SWITCH, TROUBLE CODES 10 - 4
Main
code
5
Sub
code
01
Contents
Operation panel display
check (LCD/LED CHK)
Details of function/operation
[Function]
<LED check mode (All ON/Individual ON)>
When [ENTER/START] key is pressed, all the LCD's on the operation panel are turned ON (all pixels
ON).
After 5sec of ON, the machine goes into the sub code entry standby mode.
When [MODE SWITCH] key is pressed under the all ON state, the mode is shifted to the individual
ON mode, where the LED's are turned on one by one from the left upper end to the left lower side
then from the right upper side to the right lower side. (All the pixels of LCD are lighted simultaneously.)
After lighting all the LCD's sequentially, all the LCD's are lighted simultaneously. After 5sec from lighting all the LCD's simultaneously, the machine goes into the sub code entry standby mode. (Cycle of
individual ON mode: ON 300ms, OFF 20ms)
When [C] key is pressed in the LED check mode, the machine goes into the sub code entry standby
mode.
When [START] key is pressed, the machine goes into the key input check mode.
<Key input check mode>
When the machine goes into the key input check mode, the LCD displays 0.
When any key is pressed after pressing a key on the operation panel, "+1" is added to the value.
Once a key is pressed, it is not recounted.
When [START] key is pressed, counting is made and the machine goes into the LED ON check mode
(LED all ON status) after 3sec.
When [C] key is pressed for the first time, it is counted. When it is pressed for the second time, the
machine goes into the sub code entry mode.
When [CA] key is pressed for the first time, it is counted. When it is pressed for the second time, the
machine goes out from the test command mode.
(Note in the key input check mode)
• Be sure to press [START] key at the last. (If it is pressed on the way, the machine goes into the LED
ON check mode.) (LED all ON status)
• Multi key input is ignored.
[Operation]
<LED check mode (All ON/Individual ON)>
1) Initial display
■■■■■■■■■■■■■■■■■■■■■
■■■■■■■■■■■■■■■■■■■■■
2) When [MODE SWITCH] key is pressed, the machine goes into the individual ON mode.
<Key input check mode>
1) Initial display
2) [ENTER/START]
05-01 LCD/LED CHK.
05-01 LCD/LED CHK.
0
02
Fusing lamp, cooling fan
operation check (HT LAMP
CHK)
**
[Function]
When [ENTER/START] key is pressed, the fusing lamp repeats ON for 500ms and OFF for 500ms 5
times. During this period, the cooling fan motor rotates.
[Operation]
1) Initial display
05-02 HT LAMP CHK
EXECUTING...
03
Copy lamp ON check
(C-LAMP CHK)
[Function]
When [ENTER/START] key is pressed, the copy lamp turns ON for 5sec.
[Operation]
1) Initial display
05-03 C-LAMP CHK
EXECUTING...
FO-DC550 TEST COMMAND, FAX SOFT SWITCH, TROUBLE CODES 10 - 5
Main
code
6
Sub
code
01
Contents
Paper feed solenoid
(CPFS1, CPFS2, MPFS)
operation check (PSOL
CHK)
Details of function/operation
[Function]
When [ENTER/START] key is pressed, the selected paper feed solenoid repeats ON for 500ms and
OF for 500ms 20times.
When [←/→/10KEY] is pressed, the paper feed solenoid setting is switched.
Code number
0
1
2
Setting
CPFS1
CPFS2
MPFS
Remark
Operation is possible only when No. 2 cassette is installed.
[Operation]
2) [←/10KEY]
1) Initial display
06-01 PSOL CHK
0:CPFS1
06-01 PSOL CHK
2:MPFS
2) [→/10KEY]
3) [ENTER/START]
06-01 PSOL CHK
1:CPFS2
06-01 PSOL CHK
EXECUTING...
4) Returns to the initial display.
02
Resist roller solenoid (RRS)
operation check (RES.R
SOL CHK)
[Function]
When [ENTER/START] key is pressed, the resist solenoid repeats ON for 500ms and OFF for 500ms
20 times.
[Operation]
1) Initial display
06-02 RES.R SOL CHK
EXECUTING...
7
01
Check of warm-up display
and aging with JAM (W-UP/
AGING)
[Function]
Copying is repeated to make the set quantity of copies.
When the test command is executed, warm-up is started and warm-up time is added for every second
from 0 and displayed.
When warm-up is completed, addition is stopped. When [CA] key is pressed, the ready lamp lights up.
After that, enter the copy quantity with [10KEY] and press [ENTER/START] key to repeat copying of
the set quantity (interval 0sec).
To cancel the test command, turn off the power or execute a test command which causes hardware
reset.
[Operation]
1) Initial display
2) After 10sec
07-01 W-UP/AGING
07-01 W-UP/AGING
0
06
Interval aging (INTERVAL
AGING)
10
[Function]
Copying is repeated to make the set quantity of copies.
When the test command is executed, warm-up is performed and the ready lamp is lighted.
Enter the copy quantity with the [10KEY] and press [ENTER/START] key, and copying is executed to
make the set quantity of copies, and the ready state is kept for 3sec, and copying is executed again to
make the set quantity of copies. These operations are repeated.
To cancel the test command, turn off the power or execute a test command which executes hardware
reset.
[Operation]
1) Initial display (Basic display of copy)
READY TO COPY
100%
A4
08
Shift to copy with warm-up
display (Shift to equivalent to
CA key) (W-UP C-MODE)
0
[Function]
Enter the test command code, and warm-up is started and warm-up time is counted for every second
from 0 and displayed.
When [CA] key is pressed during counting up, "0" is displayed on the display and counting is stopped.
However, warm-up is continued.
After completion of warm-up, counting is terminated. (The aging function is removed from test command 7-01.)
[Operation]
1) Initial display
2) After 10sec
07-08 W-UP C-MODE
07-08 W-UP C-MODE
0
10
FO-DC550 TEST COMMAND, FAX SOFT SWITCH, TROUBLE CODES 10 - 6
Main
code
8
Sub
code
01
Contents
Developing bias output
(DVLP BIAS SET.)
Details of function/operation
[Function]
When [ENTER/START] key is pressed, the developing bias signal is turned ON for 30sec.
When, however, an actual output value is measured, use test command 25-01.
After completion of this process, the machine goes into the sub code entry standby mode.
[Operation]
1) Initial display
08-01 DVLP BIAS SET.
EXECUTING...
02
Main charger output (Grid
HIGH) (MHV(H) SET.)
[Function]
When [ENTER/START] key is pressed, the main charger is outputted for 30sec in the grid voltage
HIGH move.
After completion of this process, the machine goes into the sub code entry standby mode.
[Operation]
1) Initial display
08-02 MHV(H) SET.
EXECUTING...
03
Main charger output (Grid
LOW) (MHV(L) SET.)
[Function]
When [ENTER/START] key is pressed, the main charger is outputted for 30sec in the grid voltage
LOW move.
After completion of this process, the machine goes into the sub code entry standby mode.
[Operation]
1) Initial display
08-03 MHV(L) SET.
EXECUTING...
06
Transfer charger output
(THV SET.)
[Function]
When [ENTER/START] key is pressed, the transfer charger is outputted for 30sec.
After completion of this process, the machine goes into the sub code entry standby mode.
[Operation]
1) Initial display
08-03 THV SET.
EXECUTING...
9
01
Duplex motor normal
rotation check (DPLX ROT.)
[Function]
Use the duplex motor Bios to drive the duplex motor in the normal direction (paper exit direction) for
30sec.
After completion of this process, the machine goes into the sub code entry standby mode.
[Operation]
1) Initial display
09-01 DPLX ROT.
EXECUTING...
02
Duplex motor reverse
rotation check (DPLX
ROT.REV.)
[Function]
Use the duplex motor Bios to drive the duplex motor in the reverse direction for 30sec.
After completion of this process, the machine goes into the sub code entry standby mode.
[Operation]
1) Initial display
09-02 DPLX ROT.REV.
EXECUTING...
04
Duplex motor rotating speed
adjustment (DPLX
ROT.SPEED)
[Function]
When this Test Command is executed, the currently set value is displayed.
Enter the adjustment value with [10KEY] and press [START] key. The entered value is stored and the
machine goes into the sub code entry standby mode. The greater the set value is, the higher the
speed is. The smaller the set value is, the lower the speed is. (Setting range: 1 - 13, Default: 6)
1) Initial display
09-04 DPLX ROT.SPEED
6( 1-13)
2) [→/10KEY]
09-04 DPLX ROT.SPEED
7( 1-13)
2) [←/10KEY]
09-04 DPLX ROT.SPEED
5( 1-13)
FO-DC550 TEST COMMAND, FAX SOFT SWITCH, TROUBLE CODES 10 - 7
3) [ENTER/START]
09-04 DPLX ROT.SPEED
7( 1-13)
Main
code
10
Sub
code
00
Contents
Toner motor operation
(TONER MOTOR)
Details of function/operation
[Function]
When [ENTER/START] key is pressed, the toner motor is rotated for 30sec.
After completion of this process, the machine goes into the main code entry standby mode.
[Operation]
1) Initial display
10-00 TONER MOTOR
EXECUTING...
14
00
Cancel of trouble other than
U2 (TRBL CANC.)
[Function]
Used to cancel troubles other than U2.
∗ Cancel troubles such as H trouble which writes data into EEPROM, and perform hardware reset.
[Operation]
1) Initial display
14-00 TRBL CANC.
CLEARED
16
00
U2 trouble cancel (U2 TRBL
CANC.)
[Function]
Used to cancel U2 trouble.
When [ENTER/START] key is pressed, check sum of the total counter in the EEPROM is rewritten
and hardware reset is made.
[Operation]
1) Initial display
16-00 U2 TRBL CANC.
CLEARED
22
04
JAM total counter display
(JAM TTL CNT)
[Function]
The JAM total counter is displayed.
[Operation]
1) Initial display
22-04 JAM TTL CNT
***,***
05
Total counter display (TTL
CNT)
[Function]
The total counter value is displayed.
[Operation]
1) Initial display
22-05 TTL CNT
***,***
08
SPF counter display (SPF
CNT)
[Function]
The SPF counter is displayed.
[Operation]
1) Initial display
22-08 SPF CNT
***,***
11
FAX-related counter display
[Function]
The FAX-related counter is displayed.
[Operation]
1) Initial display
SELECT COUNTER
1:PAGE
2:TIME
∗ [CLEAR] key: Returns to the main-sub code
input display.
2) Select 1
SEND PAGE:xxx,xxx
RECV PAGE:xxx,xxx
2) Select 2
TX TIME:xxxx:xx.xx
RX TIME:xxxx:xx.xx
("xxx,xxx" is the current value.)
("xxxx: xxx. xx" is the current value.)
∗ [CLEAR] key: Returns to "1) Initial display".
∗ [CLEAR] key: Returns to "1) Initial display".
FO-DC550 TEST COMMAND, FAX SOFT SWITCH, TROUBLE CODES 10 - 8
Main
code
22
Sub
code
12
Contents
Drum counter display
(DRUM CNT)
Details of function/operation
[Function]
The drum counter is displayed.
[Operation]
1) Initial display
22-12 DRUM CNT
***,***
13
CRUM type display (CRUM
TYPE)
[Function]
When the test command is executed, the CRUM type currently set (written) in the CRUM chip is
displayed.
Code number
00
01
02
03
04
99
CRUM type
Not set
BTA-A
BTA-B
BTA-C
FO-A
Conversion
Display item
0
BTA-A
BTA-B
BTA-C
FO-A
CONVERSION
[Operation]
1) The CRUM type is displayed.
22-13 CRUM TYPE
01:BTA-A
14
ROM version display (ROM
VER.)
[Function]
The P-ROM version is displayed.
Press [←/→/10KEY] to switch the display version.
Code number
0
1
2
Version
Main unit Program
F-IMC Program
LCD DATA
Display item
MAIN PROG.
F-IMC PROG.
LCD DATA
[Operation]
2) [→/10KEY]
1) Initial display
22-14 ROM VER.
MAIN PROG.
00.00
22-14 ROM VER.
F-IMC PROG.
00.00
2) [←/10KEY]
22-14 ROM VER.
LCD DATA
00.00
16
Duplex counter display
(DPLX CNT)
[Function]
The duplex counter is displayed.
[Operation]
1) Initial display
22-16 DPLX CNT
***,***
17
Copy counter display
(COPIES CNT)
[Function]
The copy counter is displayed.
[Operation]
1) Initial display
22-17 COPIES CNT
***,***
18
Printer counter display
(PRT.CNT)
[Function]
The printer counter is displayed.
[Operation]
1) Initial display
22-18 PRT.CNT
***,***
FO-DC550 TEST COMMAND, FAX SOFT SWITCH, TROUBLE CODES 10 - 9
Main
code
22
Sub
code
19
Contents
Scanner mode counter
display (S-MODE CNT)
Details of function/operation
[Function]
The scanner mode counter is displayed.
[Operation]
1) Initial display
22-19 S-MODE CNT
***,***
21
Scanner counter display
(SCAN CNT)
[Function]
The scanner counter is displayed.
[Operation]
1) Initial display
22-21 SCAN CNT
***,***
22
SPF JAM counter display (S
JAM CNT)
[Function]
The SPF JAM counter is displayed.
[Operation]
1) Initial display
22-22 S JAM CNT
***,***
24
01
JAM total counter clear (JAM
TTL CLR.)
[Function]
When [ENTER/START] key is pressed, the JAM total counter is cleared to 0 and "000,000" is displayed on the LCD.
[Operation]
1) Initial display
24-01 JAM TTL CLR.
CLEARED
000,000
04
SPF counter clear (SPF
CLR.)
[Function]
When [ENTER/START] key is pressed, the SPF counter value is cleared to 0 and "000,000" is displayed on the LCD.
[Operation]
1) Initial display
24-04 SPF CLR.
CLEARED
000,000
05
Duplex counter clear (DPLX
CLR.)
[Function]
When [ENTER/START] key is pressed, the duplex counter value is cleared to 0, and "000,000" is displayed on the LCD.
[Operation]
1) Initial display
24-05 DPLX CLR.
CLEARED
000,000
07
Drum counter clear (DRUM
CLR.)
[Function]
When [ENTER/START] key is pressed, the drum counter value is cleared to 0, and "000,000" is displayed on the LCD.
[Operation]
1) Initial display
24-07 DRUM CLR.
CLEARED
000,000
08
Copy counter clear (COPIES
CLR.)
[Function]
When [ENTER/START] key is pressed, the copy counter value is cleared to 0, and "000,000" is displayed on the LCD.
[Operation]
1) Initial display
24-08 COPIES CLR.
CLEARED
000,000
FO-DC550 TEST COMMAND, FAX SOFT SWITCH, TROUBLE CODES 10 - 10
Main
code
24
Sub
code
09
Contents
Printer counter clear
(PRT.CLR.)
Details of function/operation
[Function]
When [ENTER/START] key is pressed, the printer counter value is cleared to 0, and "000,000" is displayed on the LCD.
[Operation]
1) Initial display
24-09 PRT.CLR.
CLEARED
000,000
10
FAX counter clear (FAX
CLR.)
[Function]
When PRINT switch is pressed, the FAX count value is set to 0 and "000,000" is displayed on the
LCD.
[Operation]
1) Initial display
24-10 FAX CLR.
CLEARED
000,000
13
Scanner counter clear
(SCAN CLR.)
[Function]
When [ENTER/START] key is pressed, the scanner counter value is cleared to 0, and "000,000" is
displayed on the LCD.
[Operation]
1) Initial display
24-13 SCAN CLR.
CLEARED
000,000
14
SPF JAM total counter clear
(S JAM TTL CLR.)
[Function]
When [ENTER/START] key is pressed, the SPF JAM total counter value is cleared to 0, and
"000,000" is displayed on the LCD.
[Operation]
1) Initial display
24-14 S JAM TTL CLR.
CLEARED
000,000
15
Scanner mode counter clear
(S-MODE CLR.)
[Function]
When [ENTER/START] key is pressed, the scanner mode counter value is cleared to 0, and
"000,000" is displayed on the LCD.
[Operation]
1) Initial display
24-15 S-MODE CLR.
CLEARED
000,000
25
01
Main motor operation check
(MAIN MOTOR CHK)
[Function]
When [ENTER/START] key is pressed, the main motor (and the duplex motor in the case of a duplex
model) is operated for 30sec.
To reduce toner consumption, if the developing unit is installed, the developing bias, the main
charger, and the grid are also outputted.
In this case, laser discharge is required when stopping the motor, the polygon motor is also operated
at the same time. Check for installation of the developing unit. If it is not installed, the high voltage
above is not outputted and only the motor is rotated.
To check the developing bias, install the developing unit.
After completion of 30sec operation, the machine goes into the sub code entry standby mode.
[Operation]
1) Initial display
25-01 MAIN MOTOR CHK
EXECUTING...
10
Polygon motor operation
check (LSU CHK)
[Function]
When [ENTER/START] key is pressed, the Bios is called to rotate the polygon motor for 30sec.
After completion of 30sec operation, the operation is turned off with the Bios and the machine goes
into the sub code entry standby mode.
[Operation]
1) Initial display
25-10 LSU CHK
EXECUTING...
FO-DC550 TEST COMMAND, FAX SOFT SWITCH, TROUBLE CODES 10 - 11
Main
code
26
Sub
code
02
Contents
Details of function/operation
(R)SPF setting (SPF/RSPF)
[Function]
When this test command is executed, the current set SPF is displayed. Enter the code number corresponding to the desired SPF and press [ENTER/START] key to save the setting.
Code number
0
1
2
03
Second cassette setting
(2ND TRAY)
Main unit duplex setting
(DPLX)
Destination setting
(DESTINATION)
Second cassette
Second cassette NO
Second cassette YES
Display item
OFF
ON
[Operation]
The operation is similar to test command 21-01.
[Function]
When this test command is executed, the current set duplex is displayed. Enter the code number corresponding to the desired duplex and press [ENTER/START] key to save the setting.
Code number
0
1
06
Display item
SPF OFF
SPF ON
RSPF ON
[Operation]
The operation is similar to test command 21-01.
[Function]
When this test command is executed, the current set second cassette is displayed. Enter the code
number corresponding to the desired second cassette and press [ENTER/START] key to save the
setting.
Code number
0
1
04
SPF
SPF NO
SPF YES
RSPF YES
Duplex
Duplex NO
Duplex YES
Display item
OFF
ON
[Operation]
The operation is similar to test command 21-01.
[Function]
When this test command is executed, the current set destination is displayed. Enter the code number
corresponding to the desired destination and press [ENTER/START] key to save the setting.
Code number
0
1
2
3
Destination
Inch series
EX Japan AB series
Japan AB series
China (EX Japan AB series + China paper support)
Display item
INCH
AB
–
CHINA
∗ For Japan AB series, there is no schedule for production.
07
Machine conditions check
(CPM)
[Operation]
The operation is similar to test command 21-01.
[Function]
When this test command is executed, the current machine setting is displayed.
CPM
10 CPM
12 CPM
13 CPM
14 CPM
15 CPM
16 CPM
Coy quantity
10
12
13
14
15
16
Remark
[Operation]
1) The machine setting is displayed.
26-07 CPM
10 CPM
20
Rear edge void setting (END
EDGE)
[Function]
When this test command is executed, the current set rear edge void is displayed. Enter the code number corresponding to the desired rear edge void and press [ENTER/START] key to save the setting.
Code number
0
1
Setting
Rear edge void NO
Rear edge void YES
Display item
OFF
ON
Remark
Default
[Operation]
The operation is similar to test command 21-01.
FO-DC550 TEST COMMAND, FAX SOFT SWITCH, TROUBLE CODES 10 - 12
Main
code
26
Sub
code
30
Contents
Details of function/operation
CE mark support control ON/
OFF (CE MARK)
[Function]
When this test command is executed, the current set CE mark support control is displayed. Enter the
code number corresponding to the desired CE mark support control and press [ENTER/START] key
to save the setting.
Code number
0
1
38
Cancel of stop at drum life
over (DRUM LIFE END)
Setting
CE mark support control OFF
CE mark support control ON
Memory capacity check
(MEM.CHK)
Remark
Default (100V series)
[Operation]
The operation is similar to test command 21-01.
[Function]
When this test command is executed, the current setting is displayed. Enter the code number corresponding to the desired setting and press [ENTER/START] key to save the setting.
Code number
0
1
39
Display item
OFF
ON
Setting
Stop at drum life over
Cancel of stop at drum life over
Display item
STOP
NONSTOP
Remark
Default
[Operation]
The operation is similar to test command 21-01.
[Function]
When the test command is executed, the currently installed SDRAM of the main unit is displayed.
Code number
8
Setting
8 MBYTE
Remark
[Operation]
1) Memory capacity display
26-39 MEM.CHK
8 MBYTE
40
42
Polygon motor OFF time
setting (Time required from
completion of printing to
turning OFF the motor) (LSU
MOTOR OFF)
Transfer ON timing control
setting (TC ON TIMING)
[Function]
When this test command is executed, the current setting is displayed. Enter the code number corresponding to the desired setting and press [ENTER/START] key to save the setting.
Code number
0
1
2
3
Setting
0sec
30sec
60sec
90sec
Display item
0 SEC.
30 SEC.
60 SEC.
90 SEC.
Remark
Default
[Operation]
The operation is similar to test command 21-01.
[Function]
When this test command is executed, the currently set value of the transfer ON timing is displayed
(initial display), and the set value is saved. (Setting range: 0 – 9, Default: 5)
Code
0
1
2
3
4
5
6
7
8
9
Setting
0 msec
40 msec
–30 msec
–20 msec
–10 msec
0 msec
+10 msec
+20 msec
+30 msec
+40 msec
Remark
Default
∗ The default “5” of transfer ON timing is “330ms passed from PS release.”
∗ When set to “0,” it is the same as setting to “5.”
[Operation]
The operation is similar to test command 21-01.
FO-DC550 TEST COMMAND, FAX SOFT SWITCH, TROUBLE CODES 10 - 13
Main
code
26
Sub
code
43
Contents
Side void amount setting
(SIDE VOID)
Details of function/operation
[Function]
When this test command is executed, the currently set code of the side void quantity is displayed (initial display), and the set data are saved. (Setting range: 0 – 10, Default: 4 (= One side 2.0mm))
9
Code
0
1
2
3
4
5
6
7
8
9
10
Setting
0 mm
0.5 mm
1.0 mm
1.5 mm
2.0 mm
2.5 mm
3.0 mm
3.5 mm
4.0 mm
4.5 mm
5.0 mm
Remark
Default
∗ When the adjustment value is increased by 1, the side void is changed as follows:
Side void adjustment: The side void is increased by 0.5mm. (The side void of “Set value x 0.5mm”
is made.)
[Operation]
1) Initial display
2) [10KEY]
26-43 SIDE VOID
4( 0-10)
62
Energy-save mode copy
lamp setting (C-LAMP E-S)
3) [ENTER/START]
26-43 SIDE VOID
5( 0-10)
26-43 SIDE VOID
5( 0-10)
[Function]
Used to set half-ON /OFF of the copy lamp in the pre-heat mode.
When this test command is executed, the current set code number is displayed. Enter the desired
code number and press [ENTER/START] key to save the setting.
Code number
0
1
30
01
Paper sensor status display
(P-SENSOR)
Setting
Copy lamp OFF
Copy lamp half-ON
Display item
OFF
ON
Remark
Default
[Operation]
The operation is similar to test command 21-01.
[Function]
The paper sensor status is displayed on the LCD.
Sensor
Paper exit sensor
No. 1 tray paper width sensor
Paper entry sensor
Duplex sensor
No. 2 tray paper feed sensor
New drum cartridge sensor
Display item
POD
PD1
PPD1
PPD2
PPD3
DRST
Remark
∗ Since the manual paper feed sensor is a single bypass sensor, its status is not displayed.
∗ The width sensor is available only in the FAX models.
[Operation]
1) Initial display
30-01 P-SENSOR
2) When sensor ON
30-01 POD PD1 PD2
PPD1 PPD2 PPD3 DRST
FO-DC550 TEST COMMAND, FAX SOFT SWITCH, TROUBLE CODES 10 - 14
Main
code
41
Sub
code
06
Contents
OC cover float detection
level (OC FLOAT LEVEL)
Details of function/operation
[Function]
When this test command is executed, the current set value is displayed. When [ENTER/START] key
is pressed, the mirror base unit moves to the SPF scan position to acquire the OC cover float detection level.
When the mirror base unit returns to the home position, the acquired value is displayed.
If the detection level is not acquired, ERR display is made. (Default: 0)
Note that, this test command must be executed with the OC cover closed.
∗ If the value is 0, float detection is not performed in normal jobs.
[Operation]
1) Initial display
41-06 OC FLOAT LEVEL
0
2) [ENTER/START]
41-06 OC FLOAT LEVEL
EXECUTING...
<Canceling - when C/CA key is pressed->
After canceling, the machine goes into the sub code entry
standby mode.
THE JOB IS BEING
CANCELED.
3) When the level is acquired:
41-06 OC FLOAT LEVEL
**** OK
3) When the level is not acquired:
41-06 OC FLOAT LEVEL
**** ERR
43
01
Fusing temperature setting
(Normal copy) (FU TEMP)
[Function]
When this test command is executed, the current set code number is displayed. Press [←/→/10KEY]
key to change the setting and press [ENTER/START] key to save the setting into the EERPOM. The
machine goes into the sub code entry standby mode.
Code
0
1
2
3
4
5
6
7
8
04
Fusing temperature setting
in multi coy (FU TEMP
MULTI)
Set temperature (°C)
160
165
170
175
180
185
190
195
200
Remark
Default
[Operation]
The operation is similar to test command 21-01.
[Function]
For 20th sheet or later in multi copy, the fusing temperature is automatically changed from the temperature set with test command 43-1 to the temperature set with this test command.
When this test command is executed, the current set code number is displayed. Enter the code number and press [ENTER/START] key to change the setting.
Code
0
1
2
3
4
5
Set temperature (°C)
155
160
165
170
175
180
Remark
Default
[Operation]
The operation is similar to test command 21-01.
FO-DC550 TEST COMMAND, FAX SOFT SWITCH, TROUBLE CODES 10 - 15
Main
code
43
Sub
code
05
Contents
Fusing temperature setting
in duplex copy (FU TEMP
DPLX)
Details of function/operation
[Function]
In the case of duplex copy, the shift temperature set with this test command is applied to the fusing
temperature.
When this test command is executed, the current set code number is displayed.
Enter the desired code number and press [ENTER/START] key to save the setting.
Code
0
1
2
3
4
5
6
7
8
9
09
Postcard size paper fusing
control setting (FU CTR PCARD) (Japan model only)
Shift temperature (°C)
±0
-8
-6
-4
-2
±0
+2
+4
+6
+8
Remark
Default
[Operation]
The operation is similar to test command 21-01.
[Function]
When this test command is executed, the current set code number is displayed.
Enter the desired code number and press [ENTER/START] key to save the setting.
Code
0
1
Shift temperature (°C)
Cancel
Setting
Display item
OFF
ON
Remark
Default
∗ Setting" is default for Japan. However, there is no schedule for production of the Japan model.
11
Postcard size paper fusing
temperature setting (FU
TEMP P-CARD) (Japan
model only)
[Operation]
The operation is similar to test command 21-01.
[Function]
When this test command is executed, the current set code number is displayed.
When [←/→/10KEY] key is pressed, setting is changed. When [ENTER/START] key is pressed, setting is written into the EEPROM. The machine goes into the sub code entry standby mode.
Code
0
1
2
3
4
5
6
7
8
Shift temperature (°C)
160
165
170
175
180
185
190
195
200
Remark
Default
∗ Applied only to the Japan model. However, there is no schedule to produce the Japan model. Set-
ting is reflected only when ON with test command 43-09.
14
Fusing start temperature
setting (FU TEMP START)
[Operation]
The operation is similar to test command 21-01.
[Function]
When this test command is started, the currently set code number is displayed.
Press [←/→/10KEY] to switch the setting, and press [ENTER/START] key to save it to the EEPROM.
The machine goes to the sub code entry standby mode.
Code
0
1
2
3
4
5
6
7
8
Set temperature (°C)
160
165
170
175
180
185
190
195
200
Remark
Default
[Operation]
The operation is similar to test command 21-01.
FO-DC550 TEST COMMAND, FAX SOFT SWITCH, TROUBLE CODES 10 - 16
Main
code
46
Sub
code
01
Contents
Copy density adjustment
(300dpi) (EXP.LEVEL 300)
Details of function/operation
[Function]
Copy density is set for each mode.
When this test command is executed, the current se value is displayed in 2 digits (Default: 50).
Change the set value and press [START] key to make a copy under the set value.
When the set value is increased, the copy becomes darker. When the set value is decreased, the
copy becomes lighter.
In this case, only Exp.3 copy is made. When, however, the setting is made to make darker copy,
Exp.1 and Exp.5 copies also become darker. When made to lighter copy, Exp1. and Exp.5 copies
become lighter, too.
Press [←/→] key to switch the mode. The set value of the selected mode is displayed on the LCD.
(Adjustment value: 1 – 99)
The setting procedure of the magnification ratio is the same as that to copy operation.
Mode
AE mode (300dpi)
TEXT mode (300dpi)
PHOTO mode
TS mode (TEXT)(300dpi)
TS mode (AE)(300dpi)
Display item
AE
TEXT
PHOTO
TSTXT
Default
50
50
50
50
TSAE
50
LED
COPY mode lamp
PRINT mode lamp
SCAN mode lamp
PRINT mode lamp
SCAN mode lamp
COPY mode lamp
SCAN mode lamp
[Operation]
4) [START] Fixing and printing value (No
change on the LCD)
1) Initial display
46-01 EXP.LEVEL 300
AE
100% 50( 1-99)
∗ Print is started in the set mode.
2) [←] Mode selection
46-01 EXP.LEVEL 300
AE
100% 62( 1-99)
46-01 EXP.LEVEL 300
TSAE 100% 50( 1-99)
4) To fix the set value without printing, press
[Enter] key.
2) [→] Mode selection
46-01 EXP.LEVEL 300
AE
100% 62( 1-99)
46-01 EXP.LEVEL 300
TEXT 100% 50( 1-99)
∗ To cancel manual feed paper empty MSG,
3) [10KEY] Value entry
press any key.
46-01 EXP.LEVEL 300
AE
100% 62( 1-99)
02
Copy density adjustment
(600dpi) (EXP.LEVEL 600)
∗ When performing the AE mode exposure
adjustment, place the test chart on the document table so that the center area of 10cm is
not covered.
[Function]
Copy density is set for each mode.
When this test command is executed, the current se value is displayed in 2 digits (Default: 50).
Change the set value and press [START] key to make a copy under the set value.
When the set value is increased, the copy becomes darker. When the set value is decreased, the
copy becomes lighter.
In this case, only Exp.3 copy is made. When, however, the setting is made to make darker copy,
Exp.1 and Exp.5 copies also become darker. When made to lighter copy, Exp1. and Exp.5 copies
become lighter, too.
Press [←/→] key to switch the mode. The set value of the selected mode is displayed on the LCD.
(Adjustment value: 1 – 99)
Mode
AE mode (600dpi)
TEXT mode (600dpi)
PHOTO mode
TS mode (TEXT) (600dpi)
TS mode (AE) (600dpi)
Display item
AE
TEXT
PHOTO
TSTXT
TSAE
Default
50
50
50
50
50
LED
COPY mode lamp
PRINT mode lamp
SCAN mode lamp
PRINT mode lampSCAN mode lamp
COPY mode lampSCAN mode lamp
[Operation]
The operation is similar to test command 46-01.
FO-DC550 TEST COMMAND, FAX SOFT SWITCH, TROUBLE CODES 10 - 17
Main
code
46
Sub
code
12
Contents
Density adjustment in the
FAX mode (Collective
adjustment)
Details of function/operation
[Function]
When [START] key is pressed, scan is executed with the entered exposure adjustment value and the
data stored on the FAX side is rewritten into the entered value.
All data of the exposure adjustment values are rewritten into the same value.
For the density adjustment table data, refer to TC46-13 (density adjustment (normal text) in the FAX
mode).
[Operation]
3) Scan is started (self print), and the LED of
[START] key is turned off.
1) Initial display
ADJUST
EXP.
AUTO
XX
("XX" is the exposure adjustment value of normal text stored on the FAX side.)
2) Enter a 2-digit value as the exposure adjustment value.
ADJUST
EXP.
ADJUST
SCAN
EXP.
AUTO
YY
4) Print is started (self print).
ADJUST
PRINT
EXP.
AUTO
YY
After completion of printing, returns to “2)” display.
AUTO
YY
("YY" is the entered exposure adjustment
value.)
13
FAX mode density
adjustment (normal text)
[Function]
Scan is started with the exposure adjustment value entered with [START] key, and the stored data of
the selected mode on the FAX side is rewritten into the input value.
Density adjustment value data table
Mode
STD (Normal text)
Fine (Fine text)
Sfine (Super fine)
Photo
off
on
off
on
off
Exposure adjustment value
When initializing each data: 50
[Operation]
1) Initial display
ADJUST
EXP.
STD
XX
("XX" is the corresponding exposure adjustment
value of normal text mode stored on the FAX
side.)
2) Enter a 2-digit value as the exposure adjustment value with [10KEY].
ADJUST
EXP.
STD
YY
3) Scan is started (self print), and the LED of
[START] key is turned off.
ADJUST
SCAN
EXP.
STD
YY
4) Print is started (self print).
ADJUST
PRINT
EXP.
STD
YY
After completion of printing, returns to “2)”
display.
("YY" is the entered exposure adjustment
value.)
14
FAX mode density
adjustment (Fine text)
[Function]
When [START] key is pressed, scan is started with the entered exposure adjustment value and the
data of the selected mode on the FAX side is changed to the entered value.
For the density adjustment value table data, refer to TC46-13 (FAX mode density adjustment (normal
text).)
[Operation]
1) Initial display
ADJUST
EXP.
3) Scan start (self print)
FINE
XX
("XX" is the corresponding exposure adjustment
value of the fine text mode stored on the FAX
side.)
2) Enter a 2-digit value as the exposure adjustment value with [10KEY].
ADJUST
EXP.
ADJUST
SCAN
EXP.
FINE
YY
4) Print start (self print)
ADJUST
PRINT
EXP.
AUTO
YY
After completion of printing, returns to “2)”
display.
FINE
YY
("YY" is the entered exposure adjustment
value.)
FO-DC550 TEST COMMAND, FAX SOFT SWITCH, TROUBLE CODES 10 - 18
Main
code
46
Sub
code
15
Contents
FAX mode density
adjustment (Super fine)
Details of function/operation
[Function]
When [START] key is pressed, scan is started with the entered exposure adjustment value and the
data of the selected mode on the FAX side is changed to the entered value.
For the density adjustment value table data, refer to TC46-13 (FAX mode density adjustment (normal
text).)
[Operation]
1) Initial display
ADJUST
EXP.
3) Scan start (self print)
ADJUST
SCAN
S-FINE
XX
("XX" is the corresponding exposure adjustment
value of the super fine mode stored on the FAX
side.)
2) Enter a 2-digit value as the exposure adjustment value with [10KEY].
ADJUST
EXP.
EXP.
S-FINE
YY
4) Print start (self print)
ADJUST
PRINT
EXP.
S-FINE
YY
After completion of printing, returns to “2)”
display.
S-FINE
YY
("YY" is the entered exposure adjustment
value.)
18
Image contrast adjustment
(300dpi) (GAMMA 300)
[Function]
Contrast is set for each mode.
When this test command is executed, the current se value is displayed in 2 digits (Default: 50).
Change the set value and press [START] key to make a copy under the set value.
When the set value is increased, the contrast becomes higher. When the set value is decreased, the
contrast becomes lower.
In this case, only Exp.3 copy is made. When, however, the setting is made to make higher contrast,
Exp.1 and Exp.5 copies also become in higher contrast. When made to a lower contrast, Exp1. and
Exp.5 copies become lower contrast, too.
Press [←/→] key to switch the mode. The set value of the selected mode is displayed on the LCD.
(Adjustment value: 1 – 99)
Mode
AE mode (300dpi)
TEXT mode (300dpi)
PHOTO mode
TS mode (TEXT) (300dpi)
TS mode (AE) (300dpi)
Display item
AE
TEXT
PHOTO
TSTXT
Default
50
50
50
50
TSAE
50
LED
COPY mode lamp
PRINT mode lamp
SCAN mode lamp
PRINT mode lamp
SCAN mode lamp
COPY mode lamp
SCAN mode lamp
∗ No density display on LCD.
[Operation]
The operation is similar to test command 46-01.
FO-DC550 TEST COMMAND, FAX SOFT SWITCH, TROUBLE CODES 10 - 19
Main
code
46
Sub
code
19
Contents
Exposure mode setting (AE
MODE)
Details of function/operation
[Function]
<γ table setting>
When this test command is executed, the code number of the current set gamma table is displayed.
(Default: Japan -1/Ex Japan -2)
Enter the code number corresponding to the desired gamma table, and press [←/→] key to change
the mode and write into the EEPROM.
<AE operation mode>
When setting the γ table, press [→] key to change to the AE operation mode, and the current set code
number of the AE operation mode is displayed. (Default: 0)
Enter the code number corresponding to the desired AE operation mode and press [←/→] key to
change the mode and write into the EEPROM.
<PHOTO image process setting>
When [→] key is pressed in AE operation mode setting, the mode is changed to the PHOTO image
process setting and the code number of the current set PHOTO image process setting is displayed.
(Default: 0)
Enter the code number corresponding to the desired PHOTO image process setting and press [←/→]
key to change the mode and write into the EEPROM.
Mode
Display item
γ
GAMMA
AE
AE
PHOTO
PHOTO
Code number
1
2
0
1
1
2
Setting content
Image quality priority mode
Toner consumption priority mode
Lead edge stop
Real time process
Error diffusion process
Dither process
Remark
Japan default
EX Japan default
Default
Default
[Operation]
2) [→] Mode selection
1) Initial display
<γ table setting>
46-19 AE MODE
GAMMA
2( 1-2)
3) [10KEY] Value input
46-19 AE MODE
AE
0( 0-1)
2) [←] Mode selection
46-19 AE MODE
PHOTO
1( 1-2)
20
SPF exposure correction
(EXP.LEVEL SPF)
46-19 AE MODE
AE
1( 0-1)
4) [ENTER/START] Save the
set value. The machine
goes to the sub code entry
standby mode.
[Function]
Used to adjust the exposure correction amount in the SPF mode. The adjustment is made by adjusting Vref voltage variation for the OC mode.
When this test command is executed, the current set value is displayed in 2 digits (Default: 50).
Change the set value and press [START] key to save the setting and make a copy.
When the set value is increased, copy becomes darker. When the set value is decreased, copy
becomes lighter. (Adjustment range: 1 – 99)
Mode
SPF
Display item
SPF
Default
50
Remark
[Operation]
The operation is similar to test command 46-01.
FO-DC550 TEST COMMAND, FAX SOFT SWITCH, TROUBLE CODES 10 - 20
Main
code
46
Sub
code
29
Contents
Image contrast adjustment
(600dpi) (GAMMA 600)
Details of function/operation
[Function]
Contrast is set for each mode.
When this test command is executed, the current se value is displayed in 2 digits (Default: 50).
Change the set value and press [START] key to make a copy under the set value.
When the set value is increased, the contrast becomes higher. When the set value is decreased, the
contrast becomes lower.
In this case, only Exp.3 copy is made. When, however, the setting is made to make higher contrast,
Exp.1 and Exp.5 copies also become in higher contrast. When made to a lower contrast, Exp1. and
Exp.5 copies become lower contrast, too.
Press [←/→] key to switch the mode. The set value of the selected mode is displayed on the LCD.
(Adjustment value: 1 – 99)
Mode
AE mode (600dpi)
TEXT mode (600dpi)
PHOTO mode
TS mode (TEXT)(600dpi)
Display item
AE
TEXT
PHOTO
TSTXT
Default
50
50
50
50
TSAE
50
TS mode (AE)(600dpi)
LED
COPY mode lamp
PRINT mode lamp
SCAN mode lamp
PRINT mode lamp
SCAN mode lamp
COPY mode lamp
SCAN mode lamp
∗ No density display on LCD.
30
AE limit adjustment (AE
LIMIT)
[Operation]
The operation is similar to test command 46-01.
[Function]
Used to set the limit value in AE and AE (toner save).
Change the setting and press [ENTER/START] key to write the setting into the EEPROM. The
machine goes into the sub code entry standby mode.
By pressing [←/→] key, setting is changed. (Setting range: 0 – 31, Default: 0)
Mode
Limit value for AE
Limit value for AE (toner save)
Display item
AE
TSAE
Remark
<Remark>
When test command 26-06 (Destination setting) or test command 46-19 Auto Exposure mode is
changed, the setting of this test command is also changed to the default in connection.
31
Image sharpness
adjustment (SHARPNESS)
[Operation]
The operation is similar to test command 46-19.
[Function]
Used to adjust sharpening/blurring of image in each mode.
Image quality
Blurring
Standard
Sharpening
Setting No
0
1
2
Remark
Default
When this test command is executed, warm-up and shading are performed and the current set value
is displayed. (Default: 1)
Change the set value and press [START] key to make a copy under the set conditions.
To change the mode, press [←/→] key. The code number of the selected mode is dip0slayed on the
LCD.
Mode
AE mode
TEXT mode
PHOTO mode
TS mode (TEXT)
TS mode (AE)
Display item
AE
TEXT
PHOTO
TSTXT
Default setting
1
1
1
1
TSAE
1
LED
COPY mode lamp
PRINT mode lamp
SCAN mode lamp
PRINT mode lamp
SCAN mode lamp
COPY mode lamp
SCAN mode lamp
[Operation]
The operation is similar to test command 46-01.
FO-DC550 TEST COMMAND, FAX SOFT SWITCH, TROUBLE CODES 10 - 21
Main
code
46
Sub
code
32
Contents
Copier color reproduction
setting (COLOR
REAPPEAR)
Details of function/operation
[Function]
Used to set color reproduction in each mode. Colors easy to be copied and colors difficult to be copied
can be switched.
Set value
0
1
2
Colors easy to be copied
Purple, Blue, Red
Water blue, Green, Blue
Yellow, Red, Green
Colors difficult to be copied
Yellow, Green, Water blue
Purple, Red, Yellow
Blue, Water blue, Purple
∗ This setting has virtually no effect on black-and-white documents.
When this test command is executed, warm-up and shading are performed and the current set value
is displayed. (Default: 0)
Press [START] key to make a copy under the set conditions. At that time, color components are
changed for used in copying.
To change the mode, press [←/→] key. The code number of the selected mode is dip0slayed on the
LCD.
Specification component
Green
Red
Blue
Mode
AE mode (including TS)
TEXT mode (including TS)
PHOTO mode
39
FAX mode sharpness
adjustment
Setting No
0
1
2
Display item
AE
TEXT
PHOTO
Default setting
0
0
0
Remark
Default
LED
COPY mode lamp
PRINT mode lamp
SCAN mode lamp
[Operation]
The operation is similar to test command 46-01.
[Function]
When [START] key is pressed, scan is started with the entered sharpness adjustment value, and the
data of the selected mode stored on the FAX side is changed to the entered value.
Sharpness adjustment value data table
Mode
Sharpness adjustment value
1: STD
2: FINE
3: S-FINE
4: FINE/PHOTO
5: S-FINE/PHOTO
When initializing each data: 1
[Operation]
1) Initial display
SHARPNESS SETTING
PRESS ←,→
2) [←/→] or after 2sec
Every time when [→] key is pressed, the
second line is changed in the sequence of
No. 1 → 2 → 3 → 4 → 5 → 1.
When [←] key is pressed, the sequence is
reversed.
SHARPNESS SET (1-5)
1:STD
3) Select the arrow key 1-5, and the LED of
[START] key is lighted.
SHARPNESS SETTING
ZZZZ(0-2)
X
4) Enter a one-digit value (0-2) as the sharpness adjustment value with [10KEY].
SHARPNESS SETTING
ZZZZ(0-2)
Y
("Y" is the entered sharpness adjustment value.)
∗ [CLEAR] key: Returns to “2)” display.
5) Scan start (self print)
SHARPNESS SETTING
SCAN
Y
6) Print start (self print)
SHARPNESS SETTING
PRINT
Y
After completion of printing, returns to “4)”
display.
("ZZZZ" is the mode selected among STD,
FINE, S-FINE, FINE/PHOTO, and S-FINE/
PHOTO.)
("X" is the corresponding sharpness adjustment
value of the selected mode stored on the FAX
side.)
∗ [CLEAR] key: Returns to “2)” display.
FO-DC550 TEST COMMAND, FAX SOFT SWITCH, TROUBLE CODES 10 - 22
Main
code
48
Sub
code
01
Contents
Details of function/operation
Main scan/sub scan
direction magnification ratio
(COPY MAG.)
[Function]
Used to adjust the magnification ratio in the main scan (front/rear) direction and sub scan direction.
Enter the adjustment value with [10KEY]. Press [START] key to save the set value and make a copy.
(When the adjustment value is increased by 1, the magnification ratio is increased by 0.1%.)
The adjustment mode can be changed by pressing [←/→] key. (Adjustment range: 1 – 99, Default: 50)
Mode
Main scan direction magnification ratio
OC mode sub scan direction
magnification ratio
05
SPF/RSPF mode sub scan
direction magnification ratio
in copying (SPF/RSPF
MAG.)
Display item
F-R
SCAN
Default value
50
50
LED
PRINT mode lamp
SCAN mode lamp
[Operation]
The operation is similar to test command 46-01.
[Function]
Used to display the current SPF/RSPF mode sub scan direction magnification ratio on the LCD.
When [START] key is pressed, the entered data is acquired and saved into the EEPROM, and a copy
is made. (When the set value is increased by 1, the magnification ratio is increased by 0.1%.)
(Adjustment range: 1 – 99, Default: 50)
When adjusting the RSPF, use [2-SIDED COPY] key to select single/duplex after entering the one
page print mode, performing 2-page single copy.
For printing, regardless of the density mode and the density level,
Density mode = MANUAL
Density level = 3
Mode
Sub scan magnification ratio adjustment on the
surface of SPF/RSPF document
Sub scan magnification ratio adjustment on the
surface of RSPF document *1
Display item
SIDE1
Default
50
LED
COPY mode lamp
SIDE2
50
PRINT mode lamp
∗ When there is no document in SPF, copy is inhibited.
*1: Only when RSPF is installed. If installed, skipped.
[Operation]
The operation is similar to test command 46-01.
FO-DC550 TEST COMMAND, FAX SOFT SWITCH, TROUBLE CODES 10 - 23
Main
code
49
Sub
code
01
Contents
Download mode
(DOWNLOAD MODE)
Details of function/operation
[Function]
When this test command is executed, "DLOWNLOAD MODE" is displayed on the LCD and the
machine goes into the program writing mode from PC to Flash ROM.
Use the writing tool on the PC and write the program.
During writing, the display shows as follows:
After completion of download, turn OFF/ON the power to reset.
Status
Download data receiving
Loader function transfer
Date delete start
Data write (Boot section)
Data write (Program section)
Data write (EEPROM)
Data write (LCD)
During SUM CHECK
During BOOT SUM CHECK
During EEPROM SUM CHECK
Download complete
Display item
RECEIVING
LOADER COPYING
FLASH ERASE
BOOT WRITING
PROGRAM WRITING
E2PROM WRITING
LCD DATE WRITING
FLASH ROM SUM CHECK
BOOT SUM CHECK
EEPROM SUM CHECK
DOWNLOAD COMPLETE!
In case of an error in download, the following message is displayed on the LCD.
Error status
PC data receiving
Loader function transfer
FLASH ROM delete
Boot section FLASH ROM write
Program section FLASH ROM write
Loader section SUM CHECK
Boot section SUM CHECK
Program section SUM CHECK
E2PROM SUM CHECK
E2PROM write
E2PROM read Verify
E2PROM collating Verify
Boot section lens check
Program section lens check
E2PROM lens check
Total data size check
IMC communication error
IMC FRASH ROM write
LCD section lens check
LCD section FLASH ROM write
LCD section SUM CHECK
Display item
E-01 PC TRANS
E-02 LOADER COPY
E-03 FLASH ERASE
E-04 BOOT WRITE
E-05 PROGRAM WRITE
E-06 LOADER SUM
E-07 BOOT SUM
E-08 PROGRAM SUM
E-09 E2PROM SUM
E-10 E2PROM WRITE
E-11 E2PROM READ
E-12 E2PROM COLLATE
E-13 BOOT LENGTH
E-14 PROGRAM LENGTH
E-15 E2PROM LENGTH
E-16 DATE SIZE
E-17 IMC TRANS
E-18 IMC FLASH WRITE
E-19 LCD DATE LENGTH
E-20 LCD DATE WRITE
E-21 LCD DATE SUM
To enter the download mode, there is a method to use key operations as well as to use a test command. With the power OFF, press and hold [CA] + [←], turn on the power.
[Operation]
1) Initial display
DOWNLOAD MODE
FO-DC550 TEST COMMAND, FAX SOFT SWITCH, TROUBLE CODES 10 - 24
Main
code
50
Sub
code
01
Contents
Lead edge image position
(LEAD EDGE)
Details of function/operation
[Function]
Used to adjust the copy image position and the lead edge void amount on copy paper. The adjustment is made by adjusting the image scan start position at 100% and the print start position (resist
roller ON timing). When this test command is executed, the current set value is displayed in 2 digits.
(Center value: 50)
When [←/→] key is pressed, the setting mode and the display are changed.
Enter the adjustment value and press [START] key to save the set value and make a copy.
When the adjustment is made by the main cassette paper feed, the adjustment values of all the paper
feed ports become the same. (When the set value is increased by 1, shift is made by 0.1mm.)
Mode
Print start position (Main cassette
paper feed)
(*) Print start position (2nd
cassette paper feed)
Print start position (Manual paper
feed)
Image lead edge void amount
Image scan start position
Image rear edge void amount
Display item
TRAY1
Default
50
TRAY2
50
MFT
50
DEN-A
RRC-A
DEN-B
50
50
50
LED
COPY mode lamp
Main cassette lamp
COPY mode lamp
2nd cassette lamp
COPY mode lamp
Manual feed lamp
PRINT mode lamp
SCAN mode lamp
COPY mode lamp
PRINT mode lamp
SCAN mode lamp
(*): Support for the installation models. For non-installation models, skip.
[Adjustment procedure]
1) Set the print start position (A: COPY mode lamp ON), the lead edge void amount (B: PRINT mode
lamp ON), the scan start position (C: SCAN mode lamp) to zero, and make a copy of the scale at
100%.
2) Measure the image loss (Rmm) of the scale.
Set C = 10 x R (mm). (Example: Set to 40.)
When the value of C is increased by 10, the image loss is decreased by 1mm. (Default: 50)
3) Measure the distance (Hmm) from the paper lead edge to the image print start position.
Set A = 10 x H (mm). (Example: Set to 50.)
When the value of A is increased by 10, the image lead edge is moved to the paper lead edge by
1mm. (Default: 50).
4) Set the lead edge void amount to B = 50 (2.5mm). (Default: 50)
When the value of B is increased by 10, the void is extended by about 0.1mm. (For 25 or less,
however, the void amount is regarded as 0.)
∗ The SFP adjustment is made by adjusting the SPF image scan start position after OC adjustment.
∗ When paper is discharged, the shifter is operated.
(Example)
Distance from the paper lead edge
to the image lead edge, H = 5mm
Image loss, R = 4mm
5mm
10mm
[Operation]
The operation is similar to test command 46-01.
FO-DC550 TEST COMMAND, FAX SOFT SWITCH, TROUBLE CODES 10 - 25
Main
code
50
Sub
code
06
Contents
Copy lead edge position
adjustment (SPF/RSPF)
(SPF/RSPF EDGE)
Details of function/operation
[Function]
Used to adjust the SPF copy lead edge.
When the adjustment value of the document scan position adjustment is increased by 1, the scan
start timing is advanced by 0.1mm.
The print result is shifted to the opposite direction of the scan start position.
The adjustment mode can be changed by pressing [←/→] key. (Adjustment range: 1 – 99, Default:50)
When scanning a back surface of document, the mode must be changed to operate the RSPF by
pressing [2-SIDED COPY] key.
Mode
Front surface document scan position
adjustment
(*) Back surface document scan position
adjustment
Rear edge void adjustment (SPF)
Display item
SIDE1
Default
50
LED
COPY mode lamp
SIDE2
50
PRINT mode lamp
END
50
SCAN mode lamp
(*) : Support for the installation models. For non-installation models, skip.
∗ When there is no document in the SPF, copy is inhibited.
∗ When paper is discharged, the shifter is operated.
10
Print center offset
adjustment (PRT.OFFCENTER)
[Operation]
The operation is similar to test command 46-01.
[Function]
Used to adjust the center offset position of copy images on copy paper and that in scanning document.
When this test command is executed, the current set value is displayed.
Enter the adjustment value and press [START] key to save the setting and make a copy. (When the
set value is changed by 1, the center is shifted by 0.1mm.)
When the adjustment value is increased, the center is shifted to right. When decreased, the center is
shifted to left.
The modes can be selected by pressing [←/→] key.
When the set value is changed largely, the area outside the shading area may be scanned to cause
black streaks on the edges. When the RSPF is used, select the mode for use of the RSPF by [2SIDED COPY] key.
Mode
Print center offset (Main cassette paper
feed)
(*) Print center offset (2nd cassette paper
feed)
Print center offset (Manual paper feed)
Display item
TRAY1
Default
50
TRAY2
50
MFT
50
(*) 2nd print center offset (Main cassette
paper feed)
SIDE2
50
LED
COPY mode lamp
Main cassette lamp
COPY mode lamp
2nd cassette lamp
COPY mode lamp
Manual feed lamp
PRINT mode lamp
Main cassette lamp
(*) : Support for the installation models. For non-installation models, skip.
∗ In the 2nd print center offset adjustment, print is made forcibly as 1to2/Short Edge from OC regard-
less of duplex setting.
∗ When paper is discharged, the shifter is operated.
12
Document feed off-center
adjustment (ORG.OFFCENTER)
[Operation]
The operation is similar to test command 46-01.
[Function]
Used to adjust document scan off-center adjustment.
The adjustment modes can be selected by pressing [←/→] key. (Adjustment range: 1 – 99, Default:50)
When the adjustment value is increased, the print result is shifted to left.
Mode
Platen document scan
(*) SPF document front scan
(*) RSPF document back scan
Display item
OC
SPF
RSPF
Default
50
50
50
(*) : Support for the installation models. For non-installation models, skip.
∗ When paper is discharged, the shifter is operated.
[Operation]
The operation is similar to test command 46-01.
FO-DC550 TEST COMMAND, FAX SOFT SWITCH, TROUBLE CODES 10 - 26
LED
COPY mode lamp
PRINT mode lamp
SCAN mode lamp
Main
code
50
Sub
code
18
Contents
Memory reverse position
adjustment in duplex copy
(DPLX REVERSE)
Details of function/operation
[Function]
When this test command is executed, the current set correction value is displayed.
Enter the correction value and press [START] key to save the entered correction value. (Correction
value range; 1 – 99, Default: 50)
For S-D mode front surface print and print of even paged in D-S mode, reverse memory copy operation is performed from the rear edge of documents.
When, therefore, the print position adjustment of output images is required, adjust as follows:
In the reverse memory coping, when the document scan is made in the arrow direction, the output
image is printed from the rear edge of scan image,
When, therefore, the print lead edge is shifted, set the reference chart so that the reference position is
on the rear edge, and use this test command to adjust the set value so that the print lead edge is
matched.
Since printing is made from the image data most lately stored in memory to the lead edge data from
the print start position, the image lead edge adjustment is made by changing the end data position
stored in memory by the set value of this test command.
Since it is performed by changing the scan end position, the image position adjustment is made by
changing the scan end position and the end data stored in memory.
Mode
Display item
OC memory reverse output position
OC
SPF memory reverse output position *1
SPF
*1: Only when SPF/RSPF is installed. If installed, skipped.
Default
50
50
Document transport direction
Print lead edge
Lead edge void (1)
Print start position
Document transport direction
Scan lead edge
Scan end position
(Default: Scan cut by void (1))
Scan direction
LED
COPY mode lamp
PRINT mode lamp
Rear edge void
Print rear edge
Scan rear edge
∗ The initial value of duplex setting is "1to2/Long Edge" for the duplex model, or "2to1" for the simplex
model.
∗ When paper is discharged, the shifter is operated.
19
Duplex copy rear edge void
adjustment (DPLX END
EDGE)
[Operation]
The operation is similar to test command 46-01.
[Function]
Used to adjust the rear edge void amount in duplex copy.
When this test command is executed, the current set value is displayed in 2 digits. (Center value: 50.)
The adjustment modes can be selected by pressing [←/→] key. (Adjustment range; 1 – 99)
Enter the adjustment value and press [START] key to save the set value and make a copy. (The
paper information is cleared for every copy.)
When the set value is increased by 1, the void amount is increased by about 0.1mm.
Mode
Paper rear edge void amount
Print start position (Duplex back surface)
Display item
DEN-B
RRC-D
Default
50
50
LED
PRINT mode lamp
SCAN mode lamp
∗ The initial value for duplex setting is "1to2/Short Edge" for the OC/SPF setting, or "2to2" for the
RSPF setting.
∗ When paper is discharged, the shifter is operated.
[Operation]
The operation is similar to test command 46-01.
FO-DC550 TEST COMMAND, FAX SOFT SWITCH, TROUBLE CODES 10 - 27
Main
code
51
Sub
code
02
Contents
Resist amount adjustment
(RESIST ADJ.)
Details of function/operation
[Function]
Used to adjust the contact pressure of the main unit resist roller and the RSPF resist roller onto paper.
When this test command is executed, the current set value is displayed.
The adjustment modes can be selected by pressing [←/→] key.
Enter the adjustment value with [10KEY] and press [START] key to save the set value and make a
copy.
Mode
Main cassette paper fed
Display item
TRAY1
Default
50
TRAY2
50
MFT
50
(*) RSPF document paper feed
(Front surface)
SIDE1
50
(*) RSPF document paper feed
(Back surface)
(*) Duplex back surface
SIDE2
50
DUP-2
50
(*) 2nd cassette paper feed
Manual paper feed
LED
COPY mode lamp
Main cassette lamp
COPY mode lamp
2nd cassette lamp
COPY mode lamp
Manual feed lamp
COPY mode lamp
PRINT mode lamp
SCAN mode lamp
COPY mode lamp
PRINT mode lamp
PRINT mode lamp
SCAN mode lamp
(*): Support for the installation models. For non-installation models, skip.
53
08
SPF scan position automatic
adjustment (SPF AUTO)
[Operation]
The operation is similar to test command 46-01.
[Function]
Place a black chart so that it covers the SPF scan glass and the OC glass together, and close the OC
cover.
When this test command is executed, the current adjustment value is displayed as the initial display.
∗ Default is 1. Adjustment range is 1 – 99. Adjustment unit 1 = about 0.127mm
∗ If the values are kept as the default values, SPF scan is not performed properly. The front area of
the proper scan position may be scanned.
In case of AUTO, press [START] key, and the mirror unit scans from the home position to the SPF
scan position with the adjustment value displayed. The SPF glass cover edge position is calculated
from the difference between the SPFG glass cover edge and the OC side document glass CCD output level. If the adjustment is normal, the adjusted value is displayed. If abnormal, the error LED lights
up with the current set value displayed.
During the error LED is lighted, when [START] key is pressed again, execution is performed again.
Mode
SPF scan position auto adjustment
SPF scan position manual adjustment
Display item
AUTO
MANU
Default
1
1
LED
COPY mode lamp
PRINT mode lamp
[Operation]
The operation is similar to test command 46-01. (In MANUAL)
OK/ERR display in AUTO
<When OK>
53-08 SPF AUTO
AUTO 100% **
61
03
HSYNC output check (LSU
CHK)
<When ERR>
OK
53-08 SPF AUTO
AUTO 100% **
ERR
[Function]
When [ENTER/START] key is pressed, HSYNC is performed and the polygon motor is rotated for
30sec.
At that time, the COPY mode lamp is lighted for 100msec every time when HSYNC is detected.
[Operation]
1) Initial display
61-03 LSU CHK
EXECUTING...
FO-DC550 TEST COMMAND, FAX SOFT SWITCH, TROUBLE CODES 10 - 28
Main
code
63
Sub
code
01
Contents
Shading check (SHADING
CHK)
Details of function/operation
[Function]
Used to display the detection level of white plate for shading.
When [ENTER/START] key is pressed, the mirror base unit moves to the white plate for shading and
the copy lamp is lighted.
When the light quantity is stabilized, revision is made for every second, and the level of one pixel at
the center of CCD which is not corrected is detected and the value is displayed in decimal values on
the LCD. (3 digits)
[Operation]
1) Initial display
63-01 SHADING CHK
EXECUTING...
000
02
Black level automatic
correction (BLACK LEVEL)
[Function]
Used to acquire the black level target value used for the black level adjustment of white balance.
When this test command is executed, the current correction value is displayed in 3 digits of 12bit
hexadecimal number.
Place the gray gradation chart (UKOG-0162FCZZ) used as the correction document so that the density 10 (black side) comes on the left side and that the chart is upside down at the center of the plate
left center.
10
Chart back surface
When [ENTER/START] key is pressed, the mirror base unit scans the chart and calculates the correction value.
After completion of correction, the corrected value is displayed on the LCD.
∗ Default: 0
∗ If the value is set to the default, operation is made with 0x60.
[Operation]
1) Initial display
63-02 BLACK LEVEL
000
2) [ENTER/START] Correction start
63-02 BLACK LEVEL
EXECUTING...
<During canceling - When C/CA is pressed->
After canceling, the machine goes into the sub code entry
standby mode.
THE JOB IS BEING
CANCELED.
3) After execution
63-02 BLACK LEVEL
*** OK
3) In case of an error
63-02 BLACK LEVEL
*** ERR
FO-DC550 TEST COMMAND, FAX SOFT SWITCH, TROUBLE CODES 10 - 29
Main
code
64
Sub
code
01
Contents
Self print (1by2 mode)
(SELF PRT.)
Details of function/operation
[Function]
The status of the optical section is ignored and printing of one page is made. Also when the print command is received from the host, printing is made.
When this test command is executed, warm-up is performed and the ready lamp is lighted. (Since,
however, the scanner is disabled, initializing is not made.)
Enter the code number and press [ENTER/START] key to start paper feed from the selected cassette
and print in the selected pattern.
Code number
0
1
2
3
Pattern
1by2
Grid pattern
White paper
Black background
Display item
1 BY 2
CHECK
WHITE
BLACK
∗ For 4 – 99, flip.
66
01
FAX soft SW setting
[Operation]
The operation is similar to test command 21-01.
[Function]
Use to check the FAX soft SW setting.
Every time when the key is pressed, the bit on the first line is switched 0 and 1.
[Operation]
1) Initial display
ENTER FAX SOFT SW. #
(3 DIGITS)
SW.___
∗ [CLEAR] key: Returns to the main-sub code
input display.
2) Enter a 3-digit value of soft SW No. (To
enter the fourth digit, shift to the left.), and
the press [ENTER] key.
No.###
CHANGE?
xxxxxxxx
1:YES 2:NO
"xxxxxxxx" is the set content.
∗ Select 2: Returns to the soft SW No. entry dis-
3) Select 1
No.###
xxxxxxxx
USE # KEY
12345678
4) Change with 1-8 of [10KEY] and the press
[ENTER] key.
No.###
STORED?
xxxxxxxx
1:YES 2:NO
"xxxxxxxx" is the set content.
∗ Select 2: Returns to the soft SW No. entry dis-
play.
5) Select 1
STORED
play.
After 2sec, returns to "1) Initial display".
02
FAX soft SW initializing
(excluding the adjustment
values)
[Function]
Use to initializing FAX soft SW.
[Operation]
1) Initial display
INITIALIZED
After 2sec, main code and sub code input display.
FO-DC550 TEST COMMAND, FAX SOFT SWITCH, TROUBLE CODES 10 - 30
Main
code
66
Sub
code
03
Contents
FAX PWB memory check
Details of function/operation
[Function]
Use to check the FAX PWB memory.
[Operation]
1) Initial display
SELECT CHECK MEMORY
PRESS ←, →
2) [←/→] or after 2sec
Every time when [→] key is pressed, the second line is changed in the sequence of No. 1 → 2 →
3 → 1.
When [←] key is pressed, the sequence is reversed.
SELECT MEMORY (1-3)
1:DRAM
SELECT MEMORY (1-3)
2:SRAM
SELECT MEMORY (1-3)
3:FLASH
∗ [CLEAR] key: Returns to the main-sub code input display.
3) [ENTER] key
CHECKING MEMORY
4) After completion of check
• When the result is OK
• In case of address bus check
error
MEMORY CHECK RESULT
OK
MEMORY CHECK RESULT
XXXXXXXX A-BUS NG
• In case of sum check error
• In case of data check error
MEMORY CHECK RESULT
XXXXXXXX SUM
NG
MEMORY CHECK RESULT
XXXXXXXX DATA
NG
• In case of data bus check
error
MEMORY CHECK RESULT
XXXXXXXX D-BUS NG
• In case of erase check error
MEMORY CHECK RESULT
XXXXXXXX ERASE NG
∗ [CLEAR] key: Returns to "1) Initial display".
04
Signal send mode (Max.
value)
[Function]
Use to set the signal send mode (Max. value).
Facsimile test command design specifications.
1
2
3
4
5
6
7
8
9
10
11
12
NO SIGNAL
33600bps(V34)
31200bps(V34)
28800bps(V34)
26400bps(V34)
24000bps(V34)
21600bps(V34)
19200bps(V34)
16800bps(V34)
14400bps(V34)
12000bps(V34)
9600bps(V34)
13
14
15
16
17
18
19
20
21
22
23
24
7200bps(V34)
4800bps(V34)
2400bps(V34)
14400bps(V33)
12000bps(V33)
14400bps(V17)
12000bps(V17)
9600bps(V17)
7200bps(V17)
9600bps(V29)
7200bps(V29)
4800bps(V27ter)
25
26
27
28
29
30
31
32
33
34
35
[Operation]
1) Initial display
SELECT OUTPUT SIGNAL
(2 DIGITS)
No.___
2) 2-digit (1-35) with [10KEY] / [←/→] / 2sec after
Pressing [→] key or [←] key reverses the sequence.
No. (1-35)
1:NO SIGNAL
.....
No. (1-35)
35:LINE ON HOOK
∗ [CLEAR] key: Returns to the main-sub code input display.
3) [ENTER] key
Send after setting
OUTPUTING SIGNAL MAX
PRESS CLEAR TO STOP
∗ [CLEAR] key: Returns to "1) Initial display".
FO-DC550 TEST COMMAND, FAX SOFT SWITCH, TROUBLE CODES 10 - 31
2400bps(V27ter)
300bps(FLAG)
2100Hz(CED)
1100Hz(CNG)
300bps(V21)
2100Hz(ANSam)
DUMMY RING
NO VOICE ANSWER
NO RING BACK TONE
LINE OFF HOOK
LINE ON HOOK
Main
code
66
Sub
code
05
Contents
Signal send mode (Soft SW
set value)
Details of function/operation
[Function]
Use to set the signal send mode (Soft SW set value).
Facsimile test command design specifications.
1
2
3
4
5
6
7
8
9
10
11
12
NO SIGNAL
33600bps(V34)
31200bps(V34)
28800bps(V34)
26400bps(V34)
24000bps(V34)
21600bps(V34)
19200bps(V34)
16800bps(V34)
14400bps(V34)
12000bps(V34)
9600bps(V34)
13
14
15
16
17
18
19
20
21
22
23
24
7200bps(V34)
4800bps(V34)
2400bps(V34)
14400bps(V33)
12000bps(V33)
14400bps(V17)
12000bps(V17)
9600bps(V17)
7200bps(V17)
9600bps(V29)
7200bps(V29)
4800bps(V27ter)
25
26
27
28
29
30
31
32
33
34
35
2400bps(V27ter)
300bps(FLAG)
2100Hz(CED)
1100Hz(CNG)
300bps(V21)
2100Hz(ANSam)
DUMMY RING
NO VOICE ANSWER
NO RING BACK TONE
LINE OFF HOOK
LINE ON HOOK
[Operation]
1) Initial display
SELECT OUTPUT SIGNAL
(2 DIGITS)
No.___
2) 2-digit (1-35) with [10KEY] / [←/→] / 2sec after
Pressing [→] key or [←] key reverses the sequence.
No. (1-35)
1:NO SIGNAL
.....
No. (1-35)
35:LINE ON HOOK
∗ [CLEAR] key: Returns to the main-sub code input display.
3) [ENTER] key
Send after setting
OUTPUTING SIGNAL SSW
PRESS CLEAR TO STOP
∗ [CLEAR] key: Returns to "1) Initial display".
07
Image memory content print
[Function]
Use to print the image memory content.
[Operation]
• When print is allowed
PRINT STORED
After completion of printing,
main code and sub code input
display.
10
Image memory content clear
• When there is no print data
NO DATA
• When print is inhibited
CAN NOT PRINT
After 2 sec, FAX control is
terminated.
After 2 sec, main code and sub
code input display.
[Function]
Use to clear the image memory content.
[Operation]
• When there are some print data
CLEAR IMAGE MEMORY
After completion of memory clear, the buzzer
sounds.
CLEARED
PLEASE POWER OFF
Remains unchanged until the power is turned
off.
• When there are no print data
CLEAR IMAGE MEMORY
After completion of memory clear
CLEARED
After 2sec, main code and sub code input display.
FO-DC550 TEST COMMAND, FAX SOFT SWITCH, TROUBLE CODES 10 - 32
Main
code
66
Sub
code
11
Contents
300bps signal send (Max.
value)
Details of function/operation
[Function]
Use to set the 300bps signal send (Max. value).
1:
2:
3:
4:
5:
6:
NO SIGNAL
11111
11110
00000
010101
00001
[Operation]
1) Initial display
SELECT SIGNAL
PRESS ←, →
2) [←/→] or after 2sec
Every time when [→] key is pressed, the second line is changed in the sequence of No. 1 → 2 →
3 → 4 → 5 → 6 → 1.
When [←] key is pressed, the sequence is reversed.
SELECT SIGNAL (1-6)
1:NO SIGNAL
.....
SELECT SIGNAL (1-6)
6:00001
∗ [CLEAR] key: Returns to the main-sub code input display.
3) [ENTER] key
OUTPUTING SIGNAL MAX
PRESS CLEAR TO STOP
∗ [CLEAR] key: Returns to "1) Initial display".
12
300bps signal send (Soft
SW set value)
[Function]
Use to set the 300bps signal send (Soft SW set value).
1:
2:
3:
4:
5:
6:
NO SIGNAL
11111
11110
00000
010101
00001
[Operation]
1) Initial display
SELECT SIGNAL
PRESS ←, →
2) [←/→] or after 2sec
Every time when [→] key is pressed, the second line is changed in the sequence of No. 1 → 2 →
3 → 4 → 5 → 6 → 1.
When [←] key is pressed, the sequence is reversed.
SELECT SIGNAL (1-6)
1:NO SIGNAL
.....
SELECT SIGNAL (1-6)
6:00001
∗ [CLEAR] key: Returns to the main-sub code input display.
3) [ENTER] key
OUTPUTING SIGNAL SSW
PRESS CLEAR TO STOP
∗ [CLEAR] key: Returns to "1) Initial display".
FO-DC550 TEST COMMAND, FAX SOFT SWITCH, TROUBLE CODES 10 - 33
Main
code
66
Sub
code
13
Contents
Dial test
Details of function/operation
[Function]
Use to the dial test.
[Operation]
■ Dial test (PULSE)
■ Dial test (DTMF)
1) Initial display
1) Initial display
SELECT SIGNAL
1:PULSE
2:DTMF
SELECT SIGNAL
1:PULSE
2:DTMF
∗ [CLEAR] key: Returns to the main-
∗ [CLEAR] key: Returns to the main-sub code input dis-
sub code input display.
play.
2) Select 1
INPUT MAKE TIME
(0-15)
2)
__
Select 2
SELECT HIGH LEVEL
1:DEFAULT 2:SOFT SW.
↓
3) Enter the make time in 2 digits.
INPUT DIAL #
XXXX
XXXX: Default
∗ After deleting with [CLEAR] key,
input can be made.
INPUT VALUE
(0-15)
↓
3)
SELECT LOW LEVEL
1:DEFAULT 2:SOFT SW.
↓
SEND yyPPS xxms
1:YES 2:NO
"xx" is the input value.
∗ Select 2: Returns to “2)” display.
5) Select 1
Switched to 10/20PPS set with
pulse selection inside.
6) After setting
SENDING yyPPS xxms
__
↓
Select 1
4) [ENTER] key
"yy" is the selected pulse 10 or 20.
Select 2
Select 2
INPUT VALUE
(0-15)
↓
__
↓
4) Select 1
INPUT DIAL #
XXXX
XXXX: Default
∗ After deleting with [CLEAR] key, input can be made.
4) [ENTER] key
H:xx
1:YES 2:NO
L:yy
"xx" indicates HI, and "yy" indicates Low Soft SW.
7) After completion of sending
TERMINATE ?
1:YES 2:NO
∗ Select 2: Returns to “4)” display.
8) Select 1
∗ Select 2: Returns to “4)” display.
5) Select 1
HI/LO is selected with the signal level inside.
6) After setting the signal send level
SENDING DTMF
TERMINATED
After 2sec, returns to "1) Initial display".
7) After completion of sending
TERMINATE ?
1:YES 2:NO
∗ Select 2: Returns to “4)” display.
8) Select 1
TERMINATED
After 2sec, returns to "1) Initial display".
17
DTMF signal send (Max.
value)
[Function]
Use to set the DTMF signal send (Max. value).
[Operation]
1) Initial display
INPUT DIAL #
∗ [CLEAR] key: Returns to the main-sub code
input display.
3) Communication is started after setting the
signal send level.
SENDING SIGNAL MAX
PRESS CLEAR TO STOP
∗ [CLEAR] key: Returns to "1) Initial display".
2) [10KEY] input
The content selected with signal send level
selection is set inside.
FO-DC550 TEST COMMAND, FAX SOFT SWITCH, TROUBLE CODES 10 - 34
Main
code
66
Sub
code
18
Contents
DTMF signal send (Soft SW
set value)
Details of function/operation
[Function]
Use to set the DTMF signal send (Soft SW set value).
[Operation]
1) Initial display
3) Communication is started after setting the
signal send level.
INPUT DIAL #
∗ [CLEAR] key: Returns to the main-sub code
SENDING SIGNAL SSW
PRESS CLEAR TO STOP
∗ [CLEAR] key: Returns to "1) Initial display".
input display.
2) [10KEY] input
The content selected with signal send level
selection is set inside.
21
FAX information print
[Function]
Use to print the FAX information.
[Operation]
1) Initial display
SELECT REPORT (1-3)
PRESS ←, →
2) [←/→] or after 2sec
Every time when [→] key is pressed, the second line is changed in the sequence of 1 → 2 → 3 →
1.
When [←] key is pressed, the sequence is reversed.
SELECT REPORT (1-3)
1:USER SW. LIST
SELECT REPORT (1-3)
2:SOFT SW. LIST
SELECT REPORT (1-3)
3:PROTOCOL
∗ [CLEAR] key: Returns to the main-sub code input display.
3) [ENTER] key
• When print is allowed
• When print is inhibited
PRINT STORED
After completion of printing,
main code and sub code input
display.
24
FAST SRAM clear
CAN NOT PRINT
After 2sec, FAX control is
terminated.
[Function]
Use to clear the FAST SRAM.
[Operation]
1) Initial display
CLEAR FAST SRAM
2) After completion of clearing
CLEARED
After 2sec, main code and sub code input display.
30
TEL/LIU status change
check
[Function]
Use to check the TEL/LIU status change.
[Operation]
1) Initial display
HS2 :xxx
RHS :xxx
HS1 :xxx
EXHS:xxx
↑
The display is switched every 2sec.
↓
CHECKING
PRESS CLEAR TO STOP
∗ [CLEAR] key: Returns to the main-sub code input display.
FO-DC550 TEST COMMAND, FAX SOFT SWITCH, TROUBLE CODES 10 - 35
Main
code
66
Sub
code
32
Contents
Receive data check
Details of function/operation
[Function]
Use to check the receive data.
[Operation]
1) Initial display
2) After completion of reception
RECEIVING
RESULT
xx
"xx" is "OK" or "NG" depending on the check
result.
∗ [CLEAR] key: Returns to the main-sub code
input display.
33
Signal detection check
[Function]
Use to check the signal detection.
[Operation]
1) Initial display
CHECKING
NONE
PRESS CLEAR TO STOP
When a signal is detected, the display is changed from NONE to the following.
CI/CNG/CED/BT/DT/Flag/SDT/DTMF
∗ [CLEAR] key: Returns to the main-sub code input display.
34
Communication time
measurement
[Function]
Use to measurement the communication time.
[Operation]
1) Initial display
COMM. TIME
xx:xx:xx:xxx msec
"xx:xx:xx:xxx" indicates o'clock, minute, second, millisecond.
∗ [CLEAR] key: Returns to the main-sub code input display.
37
Speaker sound volume
setting
[Function]
Use to set the speaker sound volume.
1:
2:
3:
4:
NO SOUND
LOW
MID
HIGH
[Operation]
1) Initial display
SELECT SPEEKER VOL.
PRESS ←, →
2) [←/→] or after 2sec
Every time when [→] key is pressed, the second line is changed in the sequence of 1 → 2 → 3 →
4 → 1.
When [←] key is pressed, the sequence is reversed.
SELECT (1-4)
1:NO SOUND
SELECT (1-4)
2:LOW
.....
∗ [CLEAR] key: Returns to the main-sub code input display.
3) [ENTER] key
STORED
xxx
xxx: Set content
After 2sec, main code and sub code input display.
FO-DC550 TEST COMMAND, FAX SOFT SWITCH, TROUBLE CODES 10 - 36
Main
code
66
Sub
code
38
Contents
Time setting/check
Details of function/operation
[Function]
Use to check the time setting.
[Operation]
1) Initial display
SELECT TO SET
1:DATE
2:TIME
∗ [CLEAR] key: Returns to the main-sub code
input display.
2) Select 1
xxxx.xx.xx(xxx)
CHANGE?
1:YES 2:NO
2) Select 2
xx:xx
CHANGE?
1:YES 2:NO
"xxxx.xx.xx(xxx)" is the current value. (No revision of display)
"xx:xx" is the current value.
3)
3) Select 1
Select 1
INPUT YEAR
(4 DIGITS)____.__.__
INPUT HOUR
(0-24)
__:__
∗ Select 2: Returns to "1) Initial display".
∗ Select 2: Returns to "1) Initial display".
4) Enter the year in 4 digits.
4) Enter o'clock in 2 digits.
INPUT MONTH
(1-12)
1998.__.__
5) Enter the month in 2 digits.
INPUT DAY
(1-31)
1998.01.__
6) Enter the day in 2 digits.
xxxx.xx.xx(xxx)
STORED?
1:YES 2:NO
"xxxx.xx.xx(xxx) is the entered value.
∗ Select 2: Returns to "1) Initial display".
7) Select 1
INPUT MINUTE
(00-59)
01:__
5) Enter minute in 2 digits.
xx:xx
STORED?
1:YES 2:NO
"xx:xx" is the current value.
∗ Select 2: Returns to "1) Initial display".
6) Select 1
STORED
After 2sec, returns to "1) Initial display".
STORED
After 2sec, returns to "1) Initial display".
41
CI signal check
[Function]
Use to check the CI signal.
When CI signal is detected, OFF → ON.
[Operation]
1) Initial display
CHECKING
CI:OFF
PRESS CLEAR TO STOP
∗ [CLEAR] key: Returns to the main-sub code input display.
70
Print hold passcode check
[Function]
Use to check print hold passcode.
∗ This function is used when the user forgets his/her passcode.
[Operation]
1) Initial display
PRINT HOLD PASSCODE
XXXX
XXXX: Print hold passcode.
When no passcode is registered, "PASSCODE NOT STORED” is displayed.
∗ [CLEAR] key: Returns to the main-sub code input display.
FO-DC550 TEST COMMAND, FAX SOFT SWITCH, TROUBLE CODES 10 - 37
5. FAX soft switch setting change quick reference table
Large item
Dialing
Middle item
Switch content
Remote machine call Pause time
disable
Dial call signal
DTMF-related item
Key operator
None
User program
None
None
None
None
None
User program
User program
User program
User program
None
None
Soft SW No.
Usage
SW 5-5 – 8
When dialing disable/when error dialing
SW 48-1, 2
When dialing disable
SW 51-1 – 5 When dialing disable in PBX (private branch
exchange/Fax service, etc.)
SW 53-5 – 8 When dialing disable in PBX (private branch
exchange/Fax service, etc.)
SW 39-4 – 8 When dialing disable in PBX (private branch
exchange/Fax service, etc.)
SW 67-1 – 4 When pulse dialing disable
SW 7-3
When busy tone detection disable
SW 51-7, 8
When busy tone error is detected
SW 7-2
SW 4-1 – 4
When send errors occur frequently
SW 40-1 – 8
SW 4-5 – 8
Whey busy occurs frequently
SW 41-1 – 8
SW 12-6, 7
No call-in
SW 55-1 – 7 No call-in
None
SW 47-2
When an external telephone is connected
User program
SW 2-5 – 8
When remote switch is erroneously detected
User program
SW 8-5
When remote switch is erroneously detected
None
SW 15-4 – 8
JBIG mode
V34 mode function setup
None
None
SW 17-4, 8
SW 43-1
V34 symbol rate
None
SW43-4 – 6
G3/SG3
DIS reception check
Line equalizer
None
None
SW 6-8
SW 59-5 – 8
SG3
V34 send speed
Manual send V34
None
None
SW 44-1 – 4
SW 42-8
G3
Modem send speed
RTN reception error
CSI transmission
Maximum reception length
V34 reception speed
None
None
None
None
None
SW 16-1 – 4
SW 52-5
SW 6-3
SW 7-6
SW 44-5 – 8
When the remote machine cannot receive
signals in a proper level.
When an error occurs in the JBIG mode
When SG3 communication error occurs
frequently
When SG3 communication error occurs
frequently
When an error occurs in phase B
Setting is made referring to the distance from the
station when a communication trouble occurs.
When an error occurs in the SG3 communication.
When an error occurs in the SG3 communication
in FAX service, etc.
To specified/unspecified destination
When judged as “OK” though RTN is received
None
None
Pulse (10PPS)
Busy tone detection
Busy tone detection
Dial tone detection
Redial
In case of an error
Resend interval
In case of an error
Number of times of resend
When busy
Resend interval
When busy
Number of times of resend
Arrival (Call-in) When CI detection
CI detection
disable
CI signal OFF detection
time
External
Setting of an external Yes/No
telephone
telephone connected
Remote switch
Entry of a 2-digit number
number
Remote switch
Yes/No
setting
Communication General
Send level
Signal detection
SG3
Transmission
Reception
G3/SG3
SG3
G3
Reception print Paper selection
Index
Countermeasure against None
echo in reception
Modem speed in reception None
SW 6-4
EYE-Q check only
Automatic reduction print
Index print setup
SW 72-1
SW 24-8
SW 32-6
None
User program
User program
SW 16-5, 6
When a document of 1m or longer is received
When fall-down occurs frequently in the SG3
communication
When an error occurs in phase B in reception
When the line quality is poor and a fall-back or an
error occurs
Change in the detection method of training error
When reduction print is not made
When an index is attached to the reception data
FO-DC550 TEST COMMAND, FAX SOFT SWITCH, TROUBLE CODES 10 - 38
6. Soft switch list
∗ When outside the set range, the default value is automatically set.
∗ Never change the soft switch setup which are inhibited to use.
SW Data
Item
NO. No.
1
Image quality priority
selection
2
S
W
1
3
4
5
Inhibited to use
Auto/Manual default
setup
Switch selection and contents of functions
Bit No.
Normal
Fine
Super fine
1
0
0
1
2
0
1
0
Initial value
S
W
2
Normal
0
1: Manual reception
0: Automatic reception
Automatic
reception
Send request protection 1: Not protected
0: Protected
Inhibited to use
Inhibited to use
Remote selection
number setup
Binary input
Bit No.
Set range
5 6 7
0 to 9
8
1
1
0
0
4
0
0
0
5
8
S
W
3
1
2
3
4
5
6
7
Density default setup
Inhibited to use
Size specification
8
1
2
3
S
W
4
Recall interval in
communication error
Bit No.
Light
Medium
Dark
Bit No.
Centimeter size
Inch size
Conforms to the machine
information.
Conforms to the machine
information.
Binary input
Bit No.
Set range
4
5
6
7
Refer to User program
“RESO.PRIORITY”.
When a value outside
0 the set range is set,
the initial value is set.
0
Protected
6
7
8
1
2
3
4
5
6
7
Remark
Recall interval in busy
Binary input
Bit No.
Set range
2
0
0
0
3
0
1
0
5
0
0
1
7 8
0 0
1 0
0 1
1
Medium
Conforms to the
machine
information.
1
1 2 3 4
1 to 15min
0: Recall immediately after
cutting the line
5 6 7 8
1 to 15min
Manual reception can
be set only when
external telephone is
connected.
Refer to User program
0 “SECURITY
SELECTION”.
0
0
0
0
0
0
0
0 Refer to User program
1 “REMOTE
RECEPTION #”.
0 When a value outside
the set range is set,
1 the initial value is set.
0
0 When a value outside
0 the set range is set,
1 the initial value is set.
0
0
0
When set to
0 conformity to the
machine information,
if machine information
is uncertain, set to
1 centimeter size.
1min
0 Refer to User program
0 “RECALL INTERVAL
(LINE ERROR)”.
0 When a value outside
the set range is set,
1 the initial value is set.
3min
0 Refer to User program
0 “RECALL INTERVAL
(BUSY)”.
1 When a value outside
the set range is set,
1 the initial value is set.
8
FO-DC550 TEST COMMAND, FAX SOFT SWITCH, TROUBLE CODES 10 - 39
SW Data
Item
NO. No.
1
Inhibited to use
2
3
G3 send data
accumulation wait time
S
W
5
4
5
6
7
8
1
2
3
4
S
W
6
5
6
7
8
1
2
3
4
S
W
7
5
6
7
Pause time setup
ECM
CED signal send
CSI transmission
DIS reception
confirmation in G3 send
Inhibited to use
EOL detection timer
Countermeasure for
echo in reception (CED
tone send interval)
Countermeasure for
echo in transmission
(After reception of DIS,
hold time up to signal
send is set.)
Inhibited to use
Dial tone detection
Busy tone detection
Dial tone monitoring
time
Inhibited to use
Max. length of reception
Destination display time
when one-touch key is
pressed
8
1
S
W
8
2
3
4
5
6
7
8
1
S
W
9
2
3
4
5
6
7
8
Memory transmission/
direct transmission
default setup
Proxy reception
Inhibited to use
Quick online send
Remote select function
Number of times of
CNG detection
Switch selection and contents of functions
Initial value
Remark
0
0
Bit No.
6sec
5sec
4sec
3sec
Binary input
Bit No.
Set range
3
0
0
1
1
1:
1:
1:
1:
0: No
0: No
0: No
0: Once in NFS reception,
2 time in DIS reception
Yes
Yes
Yes
2 times
1: 25sec
1: 500ms
1: 500ms
4
0
1
0
1
5 6 7 8
1 to 15sec
0: 13sec
0: 75ms
0
2sec
0: No
0: No
0: 5sec
1: No limit
Bit No.
2sec
4sec
6sec
0:
7
0
0
1
1
0:
Yes
Yes
Yes
Once in NFS
reception, 2 time 0
in DIS reception
0
13sec
0
75ms
0
200ms
0
No
Yes
0
0
1
5sec
0
1.5m
8
0
1
0
1
Memory transmission
1.5m
0
0
2sec
When a value outside
0 the set range is set,
the initial value is set.
0
Memory
transmission
1: Yes
0: No
Yes
1: Yes
1: Yes
0: No
0: No
Yes
Binary input
Bit No.
Set range
Print of total
1: Yes
communication time
and total pages
Inhibited to use
Ringing volume pattern Binary input
number
Bit No.
Set range
0 When a value outside
0 the set range is set,
1 the initial value is set.
0
1
1
1
0: 200ms
1: Yes
1: Yes
1: 10sec
1: Direct transmission
0
6sec
6 7 8
1 to 4 times
0
1
0
1
Yes
1
3 times
0
1
1
Yes
1
Refer to User program
“REMOTE
RECEPTION
SELECT”.
When a value outside
the set range is set,
the initial value is set.
0: No
3 4 5 6 7 8
Pattern No. 1 to 35
7
FO-DC550 TEST COMMAND, FAX SOFT SWITCH, TROUBLE CODES 10 - 40
0
0 When a value outside
0 the set range is set,
0 the initial value is set.
1
1
1
SW Data
Item
NO. No.
1
Measurement of
communication time
(image)
2
Sender’s telephone
number registration
S
3
Inhibited to use
W
4
10
5
6
ECM byte/frame
S
W
11
S
W
12
7
8
1
2
3
4
5
6
7
8
1
2
3
4
5
6
S
W
13
S
W
14
0: Allow
Yes
1
Allow
0
0
0
0
1: 64 [bytes/frame]
Call time setup in
automatic transmission
(T0 timer setup)
Inhibited to use
CI detection
0: 256 [bytes/frame]
256 [bytes/
frame]
1 2 3 4 5
1 to 255sec
0: No time out
6
7
8
Binary input
Bit No.
Set range
1 2 3 4
30 to 75sec
5sec unit
N x 5 + 30sec
45sec
Speaker volume in
DTMF send
0
0
0
0
0
0
1
1
0
1
0
0 When a value outside
0 the set range is set,
1 the initial value is set.
1
0
Bit No.
4 sine wave
3 sine wave
2 sine wave
6
0
1
0
1
7
0
0
1
1
4 sine wave
When a value outside
0 the set range is set,
the initial value is set.
0
Inhibited to use
Inhibited to use
Ringing volume
Remark
0: No
26sec
6
7
8
1
2
3
4
5
6
7
8
1: Inhibit
Scanner resource
Binary input
holding time out in direct
Bit No.
send
Set range
4
5
1: Yes
Initial value
Inhibited to use
7
8
1
2
3
Switch selection and contents of functions
0
0
0
Bit No.
Silent
Small
Medium
Large
Bit No.
Not used
Small
Medium
Large
3
0
0
1
1
5
0
0
1
1
4
0
1
0
1
6
0
1
0
1
Refer to User program
1 “RINGER VOLUME”.
Medium
0
1
Medium
Inhibited to use
0
1
1
0
1
0
1
0
0
0
0
Inhibited to use
FO-DC550 TEST COMMAND, FAX SOFT SWITCH, TROUBLE CODES 10 - 41
SW Data
Item
NO. No.
1
Busy tone detection
time (Lower limit)
2
Busy tone detection
time (Upper limit)
3
Busy tone detection
S
time (Lower limit 2)
W
4
Signal send level
15
5
6
7
8
1
Modem speed
(V.33 mode or less)
Switch selection and contents of functions
3
4
5
Modem speed in
reception fixed
6
7
8
1
2
3
S
W
17
S
W
18
S
W
19
4
5
6
7
8
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
0: 250ms
1: 650ms
0: 750ms
1: 150ms
0: Follows SW15-1.
Binary input
Bit No.
Set range
4 5 6 7 8
0 (0dBm) to 26 (–26dBm)
Bit No.
V.27 2400bps
V.29 9600bps
V.27 4800bps
V.29 7200bps
V.33 14.4kbps
V.33 12.0kbps
V.17 9600bps
V.17 12.0kbps
V.17 7200bps
V.17 14.4kbps
Bit No.
No fixing
V.29-9600BPS
V.27ter-4800BPS
V.17-14400BPS
2
S
W
16
1: 350ms
1 2 3
0 0 0
0 0 0
0 0 1
0 0 1
0 1 0
0 1 1
1 0 0
1 0 1
1 0 1
Others
5 6
0 0
0 1
1 0
1 1
4
0
1
0
1
0
0
1
0
1
Initial value
250ms
0
750ms
0
Follows SW15-1. 0
–12dBm
ECM MMR (in SG3)
ECM JBIG (in SG3)
Inhibited to use
0
V.17 14.4kbps
0
0
0
No fixing
0
0
0
0
1: Yes
1: Yes
0: No (depending on the other
party’s machine)
0: No
1: Yes
0: No
1: Yes
1: Yes
1: Yes
0: No (depending on the other
party’s machine)
0: No
0: No
1: Yes
0: No
No
0
Yes
1
Yes
1
0
No
0
Yes
Yes
1
1
1
1
0
1
0
0
0
0
0
1
0
0
0
No
0
Inhibited to use
Recording table
automatic print
Inhibited to use
0 When a value outside
1 the set range is set,
1 the initial value is set.
0
0
1
Inhibited to use
Inhibited to use
MH fixed (Except for
SG3)
ECM MMR (Except for
SG3)
ECM JBIG (Except for
SG3)
Inhibited to use
MH fixed (in SG3)
Remark
0
0
FO-DC550 TEST COMMAND, FAX SOFT SWITCH, TROUBLE CODES 10 - 42
Refer to User program
“AUTO LISTING”.
SW Data
Item
NO. No.
1
Line sound monitor
range
Switch selection and contents of functions
Bit No.
OFF
Up to NSF signal send/
receive
All
2
S
W
20
S
W
21
S
W
22
S
W
23
3
4
5
6
7
8
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
1
2
3
4
S
W
24
5
6
7
8
S
W
25
1
2
3
4
5
Line monitor display
Inhibited to use
Receivable memory
capacity
Inhibited to use
8
2
0
1
1: Yes
1 0
1 1
0: No
1: 64Kbyte
0: 128Kbyte
Interval between
Binary input
completion of
Bit No.
communication and the
Set range
next call
1 2 3 4
0 to 255sec
OFF
5
6
7
0
0
128Kbyte
0
8
Inhibited to use
Inhibited to use
Bit No.
Not set.
Receive inhibit
Inhibited to use
Document output setup 1: Collective output after
in reception
completion of reception
Inhibited to use
Automatic reduction
print
3
0
0
When a value outside
the set range is set,
0
the initial value is set.
No
Inhibited to use
Specified number
reception (ANTI JUNK
FAX)
Remark
0
1sec
4
0
1
0: Output after reception of
every page
0
0
0
0
0
0
0
0
0
0
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Refer to Main menu
“ANTI JUNK FAX”.
When a value outside
0 the set range is set,
the initial value is set.
0
0
Not set.
Output after
reception of
every page
0
0
1: Allow
0: Inhibit
Allow
Automatic reduction
rate setup
Binary input
Bit No.
Set range
Transmission end
sound tone
6
7
1
0
0
Initial value
Reception end sound
tone
Bit No.
550Hz
1000Hz
1700Hz
Bit No.
550Hz
1000Hz
1700Hz
1 2 3 4
0 to 15%
5
0
0
1
7
0
0
1
6
0
1
0
8
0
1
0
10%
1000Hz
Refer to User program
1 “AUTO RCV
REDUCE”.
1
0
1
0
When a value outside
0
the set range is set,
the initial value is set.
1
0
1000Hz
FO-DC550 TEST COMMAND, FAX SOFT SWITCH, TROUBLE CODES 10 - 43
1
When a value outside
the set range is set,
the initial value is set.
SW Data
Item
Switch selection and contents of functions
NO. No.
1
Read completion sound 1: Mute
0: 1sec
2
Inhibited to use
3
Speaker volume setup
Bit No.
3 4
Silent
0 0
Small
0 1
S
4
Medium
1 0
W
Large
1 1
26
S
W
27
5
6
7
8
1
2
3
4
5
6
7
S
W
28
S
W
29
1sec
Small
Inhibited to use
Inhibited to use
Recording paper tray
selection
8
1
2
3
4
5
6
7
8
1
2
3
Initial value
Bit No.
AUTO
TRAY1
TRAY2
7
0
0
1
1
8
0
1
0
1
AUTO
Inhibited to use
Number of auto switch
calls of manual
reception → auto
reception
Binary input
Bit No.
Set range
Setup of number of
times of call rings
Binary input
Bit No.
Set range
5 6 7 8
0 to 9 times
Report output when
canceling
Inhibited to use
1: Output
0: Not output
Default data, sender
print
Inhibited to use
Date/sender print
position setup
Inhibited to use
1: ON
0: OFF
1: Inside of document
0: Outside of document
1 2 3 4
0 to 9
Not switched when 0.
0 time
4
5
6
7
2 times
8
1
S
W
30
2
3
4
5
6
7
8
Not output
Remark
0
0
Refer to User program
0 “BEEPER VOLUME
(send completion
sound / receive
completion sound /
1 scan completion
sound / alarm sound)”
0
0
0
0
0
1
1
1
1
0
Refer to User program
0 “TRAY SELECTION”.
When a value outside
the set range is set,
0 the initial value is set.
1
1
0
1
0
0
0
0
0 Refer to User program
0 “# OF RINGS
MANUAL RX”.
0 When a value outside
the set range is set,
0 the initial value is set.
0 Refer to User program
0 “# OF RINGS AUTO
RX”.
1 When a value outside
the set range is set,
0 the initial value is set.
0
0
1
0
ON
1
0
Outside of
document
FO-DC550 TEST COMMAND, FAX SOFT SWITCH, TROUBLE CODES 10 - 44
0
1
SW Data
Item
NO. No.
1
Report output
(in transmission)
Switch selection and contents of functions
Bit No.
Print inhibited
All print
Only when transmission
is failed.
2
3
4
S
W
31
5
Report output
(In broadcast and
sequential send
request)
Bit No.
Print inhibited
All print
Only the address to
which transmission is
failed
Report output
(in reception)
Bit No.
Print inhibited
All print
Only in error
6
7
Contents of send
document are printed in
memory send
Bit No.
Print inhibited
All print
Only the address to
which transmission is
failed
Distinctive ringing
Bit No.
OFF
Standard/ON
Pattern1
Pattern2
Pattern3
Pattern4
Pattern5
8
1
2
3
S
W
32
S
W
33
S
W
34
4
5
6
Inhibited to use
Index print setup
7
8
1
Inhibited to use
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
1 2
0 0
0 1
1 0
Only when
transmission is
failed.
1 1
3 4
0 0
0 1
1 0
All print
1 1
5 6
0 0
0 1
1 0
1 1
7 8
0 0
0 1
1 0
1
1
0
0
1
0
1
0
1
1
2
0
0
0
1
1
0
0
Initial value
Print inhibited
Remark
Refer to User program
1 “PRINT SELECTION”.
When a value outside
the set range is set,
0 the initial value is set.
Refer to User program
0 “PRINT SELECTION”.
When a value outside
the set range is set,
the initial value is set.
1
Refer to User program
0 “PRINT SELECTION”.
When a value outside
the set range is set,
0 the initial value is set.
Refer to User program
1 “PRINT SELECTION”.
Only the address
When a value outside
to which
the set range is set,
transmission is
the initial value is set.
failed
0
3
0
0
0
0
0
1
1
4
0
1
0
0
0
0
0
Refer to User program
“DISTINCTIVE RING”.
When a value outside
0 the set range is set,
the initial value is set.
0
0
OFF
0
0
1: Print
0: Not print
Not print
0
Refer to User program
“INDEX PRINT”.
0
0
Page number print
setup
Inhibited to use
1: Yes
Reception data duplex
print
Inhibited to use
1: Yes
Signal send level Max.
Binary input
Bit No.
Set range
0: No
Yes
1
0
0
0
0
0
0
0: No
5 6 7 8
0 (0dBm) to 15 (–15dBm)
No
–8dBm
FO-DC550 TEST COMMAND, FAX SOFT SWITCH, TROUBLE CODES 10 - 45
0
0
0
0
0
1
0
0
0
Refer to User program
“DUPLEX RCV”.
SW Data
Item
NO. No.
1
Cover function default
setup
2
Answering telephone
connection
3
CI delete max. OFF
time
S
W
35
S
W
36
S
W
37
4
5
6
7
8
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
1
S
W
39
S
W
40
3
4
5
6
7
8
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
1: Yes
0: No
1: Yes
0: No
Bit No.
5sec
10sec
15sec
20sec
Answering machine call Binary input
number setting
Bit No.
Set range
CNG/mute detection
completion time
Binary input
Bit No.
Set range
3
0
0
1
1
Initial value
4
0
1
0
1
0
Yes
1
0
5sec
0
5 6 7 8
0 to 15 times
1 2 3 4
1 to 255sec
Silence detection start
time
Binary input
Bit No.
Set range
Mute judgment time
Binary input
Bit No.
Set range
Protocol monitor
Protocol monitor save
Inhibited to use
Bit No.
Not output
Not output
Output
Output only in an error
1: Yes
5 times
5
6
7
8
1 2 3 4
0 to 15sec
5sec
5 6 7 8
0 to 15sec
(User 0 to 10sec)
0: Mute detection OFF
1
0
0
1
1
0:
5sec
Number of times of
recall in error
Binary input
Bit No.
Set range
2
0
1
0
1
No
When a value outside
the set range is set,
the initial value is set.
Refer to User program
“AM MODE”.
0
Not output
0
Yes
4 5 6 7 8
60 to 310ms
10ms unit
1 2 3 4
0 to 1 times
0
1
0
1
0
0
1
0
1
1
0
1
0
1
0
1
0
1
0
1
Inhibited to use
DTMF signal send time Binary input
Bit No.
Set range
Remark
No
45sec
2
S
W
38
Switch selection and contents of functions
5
110ms
6
7
8
1 times
FO-DC550 TEST COMMAND, FAX SOFT SWITCH, TROUBLE CODES 10 - 46
1
0
0
0
1
0
0
0
1
0
1
0
1
1
0
0
0
0
0
0
0
1
When a value outside
the set range is set,
the initial value is set.
Refer to User program
“RECALL TIMES
(LINE ERROR)”.
When a value outside
the set range is set,
the initial value is set.
SW Data
NO. No.
1
2
3
S
4
W
5
41
6
7
8
1
2
3
S
W
42
4
5
6
7
8
1
2
3
4
S
W
43
Item
Switch selection and contents of functions
Number of times of
recall in busy
Binary input
Bit No.
Set range
Direct send recall
1: Inhibit
FAX receive auto select 1: Allow
by CNG detection
0: Allow
0: Inhibit
Auto receive select in
answering telephone
connection mode
Inhibited to use
1: Allow
0: Inhibit
V.34 mode function in
manual communication
V.34 mode function
Busy tone detection
level table
V.34 primary channel
return mode
V.34 receive symbol
speed mask
1: ON
0: OFF
1: ON
1: variable (SRAM)
0: OFF
0: constant (ROM)
1: PPh
0: Sh
Bit No.
2400
2743
2800
3000
3200
3429
1: variable (SRAM)
4
0
0
0
0
1
1
0:
1: Ignore EQM value
0: Judge EQM value
6
8
S
W
44
S
W
45
1
2
3
4
5
6
7
8
1
2
6
7
8
2 times
5
7
1 2 3 4 5
0 to 14 times
Initial value
Silence detection level
table
Control channel retrain
judgment in V.34
reception
V.34 primary channel
send speed
Allow
Allow
Inhibit
5 6
0 0
0 1
1 0
1 1
0 0
0 1
constant (ROM)
1 2 3 4
When N = 0, 2400bps.
When N = 15, 33600bps.
V.34 primary channel
receive speed
Binary input
Bit No.
Receive speed =
2400 (bps) x N
5 6 7 8
When N = 0, 2400bps.
When N = 15, 33600bps.
3
FAST mode
Sequence of year/
month/day in LCD,
report, and sender
record
1: Yes
Bit No.
Year/Month/Day
Month/Day/Year
Day/Month/Year
0:
2
0
0
1
1
4
Time display format
1: am/pm
0: 24H
Refer to User program
“RECALL TIMES
(BUSY)”.
When a value outside
the set range is set,
the initial value is set.
Refer to User program
1 “FAX SIGNAL AUTO
RECEIVE”.
Refer to Main menu
0 “AM MODE”.
No
3
0
1
0
1
ON
1
ON
1
constant (ROM)
0
PPh
1
When a value outside
1 the set range is set,
the initial value is set.
3429
Binary input
Bit No.
Set range
5 6 7 8
0 to ± 360 dots
24 dot interval
0
1
constant (ROM)
0
Judge EQM
value
0
33600bps
33600bps
No
1
1
1
0
1
1
1
0
0
Refer to User program
0 “DATE&TIME
FORMAT SET”.
Month/Day/Year
When a value outside
the set range is set,
1
the initial value is set.
am/pm
Scan effective image
area main scan right
edge image loss (SPF)
0
0
0
0
0
0
1
0
0
1
0
0
0
Binary input
Bit No.
Send speed =
2400 (bps) x N
5
6
7
8
Remark
96 dots
FO-DC550 TEST COMMAND, FAX SOFT SWITCH, TROUBLE CODES 10 - 47
Refer to User program
1 “DATE&TIME
FORMAT SET”.
0
1
0
0
SW Data
Item
NO. No.
1
Specification of print
sequence in duplex print
2
Specification of rotating
direction duplex back
surface print
3
Priority in the day of
week
S
4
Center No. in FAST
W
mode
46
5
Summer time
Switch selection and contents of functions
1: Print order (214365...)
0: Reception order (123456...)
1: 180 degrees rotation
0: No 180 degrees rotation
1: Yes
0: No
1: Host-Tel-No.
0: Service-No.
1: Allow
0: Inhibit
Initial value
Print order
(214365...)
1
180 degrees
rotation
1
No
0
Service-No.
0
Inhibit
6
7
8
1
2
S
W
47
3
4
5
6
7
8
1
Inhibited to use
Inhibited to use
External telephone
connection
Inhibited to use
1: Yes
S
W
49
3
4
5
6
7
8
1
2
3
4
5
6
7
8
1
Tone/Pulse default
setup
Bit No.
10PPS
20PPS
TONE
Telephone line menu
DP dial pulse number
process
Scan effective image
area main scan left
edge image loss (SPF)
3
4
5
6
7
8
1: Inhibit
1: 10-N
Binary input
Bit No.
Set range
1
0
0
1
1
2
0
1
0
1
0: Allow
0: Normal (N)
5 6 7 8
0 to 360 dots
24 dot interval
TONE
Allow
Normal (N)
96 dots
Inhibited to use
Speaker sound volume
pattern number in
DTMF send
Line monitor volume
2
S
W
50
Yes
Refer to Entry Mode
0 “DAY LIGHT
SAVING”.
0
0
0
0
1
0
0
0
1
0
0
2
S
W
48
0: No
Remark
Line monitor volume
pattern number
Binary input
Bit No.
Set range
Bit No.
Silent
Small
Medium
Large
Binary input
Bit No.
Set range
3 4 5 6 7 8
Pattern No. 1 to 35
1 2
0 0
0 1
1 0
1 1
3 4 5 6 7 8
Pattern No. 1 to 35
21
Medium
01 (20PPS) is invalid
1 except for Japan.
Refer to User program
“DIAL MODE”.
When a value outside
0 the set range is set,
the initial value is set.
0
0
0
1
0
0
0
0
0 When a value outside
0 the set range is set,
0 the initial value is set.
0
0
1
When SPEAKER key
1 is pressed, user
setting can be made.
0
16
FO-DC550 TEST COMMAND, FAX SOFT SWITCH, TROUBLE CODES 10 - 48
0 When a value outside
1 the set range is set,
0 the initial value is set.
0
0
0
SW Data
NO. No.
1
2
3
4
5
S
W
6
51
7
Item
Switch selection and contents of functions
DTMF send level (High
group) setup
CED detection time
Busy tone detection
cycle
1: 500ms
Bit No.
2puls
4puls
6puls
10puls
Bit No.
–43dB
–35dB
–33dB
–30dB
8
1
Busy tone detection
level
2
S
W
52
3
4
5
6
7
8
S
W
53
1
2
3
4
5
6
7
Binary input
Bit No.
Set range
Inhibited to use
Super G3 disabled in
1: Super G3 enabled
the last call-out of recall
in case of an error
Error process in RTN
1: Not error
reception
Inhibited to use
V.34 control channel
communication speed
Maximum DTMF send
level
S
W
54
S
W
55
S
W
56
Scan effective image
area sub scan lead
edge image loss (SPF)
6
7
8
Binary input
Bit No.
Set range
Binary input
Bit No.
Set range
Bit No.
Modem fixed (400Hz)
420Hz–680Hz
360Hz–440Hz
245Hz–650Hz
–6dBm
1000ms
Remark
0 When a value outside
0 the set range is set,
1 the initial value is set.
1
0
0
0
2puls
0
0
–43dB
0
0
0: Super G3 disabled
0: Error
Super G3
disabled
0
Error
0
0
0
1 2 3 4
0 (0.0dBm) to 15 (–15.0dBm)
CI signal OFF detection Binary input
enable time
Bit No.
Set range
Inhibited to use
DT/BT detection
frequency range
1000ms
8
0
1
0
1
2
0
1
0
1
Binary input
Bit No.
Set range
Binary input
Scan effective image
area sub scan rear edge
Bit No.
image loss (SPF)
Set range
Inhibited to use
CI signal ON detection
enable time
0:
7
0
0
1
1
1
0
0
1
1
0: 1200bps
8
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
1
2
3
4
5
1 2 3 4 5
0 (0.0dBm) to 21 (–21.0dBm)
1.0dBm unit
1: 2400bps
Binary input
Bit No.
Set range
DTMF send level
(difference between
high and low level)
Initial value
1200bps
5 6 7 8
0 (–2.0dBm) to 15 (+5.5dBm)
0.5dBm unit
When set to 0: Low group =
High group – (–2.0) dBm
1 2 3 4
0 to 240 lines
16 line interval
6
6
0
1
0
1
0
0
0
0
1
0
0
0
144 lines
7
1 2 3
0 (155ms) to 7 (225ms)
5
0
0
1
1
+2.0dBm
96 lines
5 6 7 8
0 to 240 lines
16 line interval
1 2 3 4 5
0 to 1270ms
10ms unit
0dBm
0
1200ms
155ms
0
1
1
0
1
0
0
1
1
1
1
1
0
0
0
0
0
0
0
0
0
420Hz–680Hz
Inhibited to use
1
0
1
FO-DC550 TEST COMMAND, FAX SOFT SWITCH, TROUBLE CODES 10 - 49
SW Data
NO. No.
1
2
3
S
4
W
5
57
6
7
8
1
2
3
S
4
W
5
58
6
7
8
1
2
3
Item
Switch selection and contents of functions
Inhibited to use
Sharp machine mode
Inhibited to use
Reception gain
adjustment
5
Binary input
Bit No.
Set range
FSK signal settlement
time in double wait
Binary input
Bit No.
Set range
Reception SED ON
level
Transmission cable
amplitude equalizer
Reception cable
amplitude equalizer
8
S
W
60
S
W
61
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
1
2
3
S
W
62
4
5
6
7
8
0: OFF
4 5 6 7 8
0 (+6.0dBm) to 24 (–6.0dBm)
Step 0.5dBm
1 2 3 4
0 to 3000ms
200ms unit
5 6 7 8
Settlement time = 50 (ms) x N
+ 200 (ms)
ON
0.0dBm
1600ms
550ms
Inhibited to use
6
7
Binary input
Bit No.
Set range
Dual wait inhibit time
after CFR send
4
S
W
59
1: ON
Initial value
Scan effective image
area sub scan lead
edge image loss (SPF
back surface)
Bit No.
–43dB
–38dB
–33dB
–48dB
Bit No.
0dB
4dB
8dB
12dB
Bit No.
0dB
4dB
8dB
12dB
Binary input
Bit No.
Set range
Binary input
Scan effective image
area sub scan rear edge
Bit No.
image loss (SPF back
Set range
surface)
3
0
0
1
1
5
0
0
1
1
7
0
0
1
1
4
0
1
0
1
6
0
1
0
1
8
0
1
0
1
1 2 3 4
0 to 240 lines
16 line interval
5 6 7 8
0 to 240 lines
16 line interval
0: 9byte (240ms)
0: 1sec
4
0
0
1
1
5
0
1
0
1
0
1
0
0
1
1
0
0
1
0
0
0
0
1
1
1
0
0
1
–48dB
1
0
0dB
0
0
0dB
0
96 lines
144 lines
Inhibited to use
Inhibited to use
CI signal ON time in V.8 1: 18byte (480ms)
mode
CI signal OFF time in
1: 2sec
V.8 mode
V.8 mode ANSam
Bit No.
signal send time
3sec
4sec
5sec
6sec
Inhibited to use
Remark
0
1
1
0
1
0
0
1
0
0
0
0
0
0
0
0
0
9byte (240ms)
0
1sec
0
0
4sec
FO-DC550 TEST COMMAND, FAX SOFT SWITCH, TROUBLE CODES 10 - 50
1
0
0
0
SW Data
Item
NO. No.
1
CI receive number to
shift to non-V.34
communication
2
S
W
63
S
W
64
S
W
65
S
W
66
S
W
67
3
4
5
6
7
8
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
1
Bit No.
Does not shift.
1 times
2 times
3 times
CI send number to shift Binary input
to non-V.34
Bit No.
communication
Set range
S
W
69
3
4
5
6
7
8
1
2
3
4
5
6
7
8
1
0
0
1
1
2
0
1
0
1
3 4 5
0 to 7 times
When N=0, retrain is not made.
Initial value
1
0
2
Inhibited to use
Inhibited to use
Binary input
Bit No.
Set range
1 2 3 4
26 to 41ms
by increment of 1ms
40ms
Inhibited to use
Line open delay time in
dial test
Bit No.
2sec
3sec
4sec
5sec
1
0
0
1
1
2
0
1
0
1
Binary input
Bit No.
Set range
5 6 7 8
30 to 105sec
5sec interval
0
1
1
0
1
0
0
0
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
0
0
0
0
0
0
2sec
0
Inhibited to use
T1 timer setup
0
1
0
Inhibited to use
Make time (10PPS)
setup
Remark
2 times
Inhibited to use
2
S
W
68
Switch selection and contents of functions
40sec
Inhibited to use
FO-DC550 TEST COMMAND, FAX SOFT SWITCH, TROUBLE CODES 10 - 51
0
0
0
0
1
0
0
0
0
0
0
0
0
0
SW Data
Item
NO. No.
1
Inhibited to use
2
3
4
Reception waiting time
between frames
5
Preamble send time of
300bps
S
W
70
6
7
RCP send times
8
S
W
71
5
0
0
1
1
7
0
0
1
1
6
0
1
0
1
8
0
1
0
1
1: EYE-Q check only
0: 0 reception & EYE-Q check
2
ERR frame reception
operation
Waiting time for CED/
ANSam send start
1: Continues process.
0: Not continue process.
(Error)
3 4
0 0
0 1
1 0
0: 7 times
4
RTC EOL send times
Inhibited to use
CNG send start
Minimum flags between
frames
2
3
Phase C head dummy
data send time
4
5
6
7
1
2
3
4
5
6
7
8
3.4sec
0
0
1.0sec
1
0
3 times
0
Bit No.
2.25sec
3sec
4sec
1: 6 times
Bit No.
0.5sec
1.0sec
1.5sec
Bit No.
2-flag
3-flag
4-flag
5-flag
Bit No.
0.2sec
0.3sec
0.4sec
0.5sec
7
0
0
1
1
0
0
1
1
3
0
0
1
1
8
0
1
0
2
0
1
0
1
4
0
1
0
1
0 reception &
EYE-Q check
Not continue
process. (Error)
0
0
0
2.25sec
6 times
1
0
0
0.5sec
0
0
2-flag
0
0
0.2sec
0
0
0
Flag-adrs timer setup
(V.21-FSK)
Print effective image
area sub scan lead
edge void
Bit No.
6sec
15sec
30sec
120sec
Binary input
Bit No.
Set range
7
0
0
1
1
8
0
1
0
1
1 2 3 4
0 to 240 lines
16 line interval (600dpi)
When a value outside
the set range is set,
the initial value is set.
0
Inhibited to use
8
S
W
74
Bit No.
0.5sec
1.0sec
1.5sec
2.0sec
Bit No.
3 times
6 times
9 times
12 times
0: 3.4sec
EYE-Q check
1
Remark
0
0
0
0
1
1
0
0
8
S
W
73
1: 4.4sec
Inhibited to use
5
6
7
Initial value
0
1
0
1
2
3
4
5
6
7
8
1
3
S
W
72
Switch selection and contents of functions
0
6sec
0
32 lines
Inhibited to use
FO-DC550 TEST COMMAND, FAX SOFT SWITCH, TROUBLE CODES 10 - 52
0
0
1
0
0
0
1
1
When a value outside
the set range is set,
the initial value is set.
SW Data
Item
NO. No.
1
Inhibited to use
2
3
Communication end
sound (Buzzer sound
length) setting
S
W
75
S
W
76
S
W
77
S
W
78
S
W
79
S
W
80
S
W
81
4
5
6
7
8
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
Print effective image
area main scan void
Switch selection and contents of functions
Bit No.
3sec
1sec
Silent
Binary input
Bit No.
Set range
Set range
Scan magnification ratio 1: –
adjustment (SPF sub
Binary input
scan)
Bit No.
Set range
1: –
Print magnification
ration adjustment (main Binary input
scan)
Bit No.
Set range
Destination information
1: –
Binary input
Bit No.
Set range
Binary input
Bit No.
North America:
3
0
0
1
4
0
1
0
3sec
5 6 7 8
0 to 240 dots
16 dots interval
48 dots
0: +
+
2 3 4 5 6
0 to ±12.7%
0.1% interval
7
8
0%
0: +
+
2 3 4 5 6
0 to ±12.7%
0.1% interval
7
8
0%
0: +
+
2 3 4 5 6
0 to ±12.7%
0.1% interval
7
8
0%
0: +
+
2 3 4 5 6
0 to ±12.7%
0.1% interval
7
1
1
6
1
2
0
3
1
4
1
5
0
8
0%
7
0
8
1
North America
Language information
Remark
0
0
Scan magnification ratio 1: –
adjustment (SPF main Binary input
scan)
Bit No.
Print magnification
ration adjustment (sub
scan)
Initial value
Binary input
Bit No.
1 2 3 4 5 6 7
1: American English
8
American
English
FO-DC550 TEST COMMAND, FAX SOFT SWITCH, TROUBLE CODES 10 - 53
Communication error
0 sound is generated
even in silent setup
Refer to User program
“BEEP LENGTH”.
0 When a value outside
the set range is set,
the initial value is set.
0
0
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
0
1
1
0
1
0
1
0 Only command
0 receive from the main
0 unit can be rewritten.
0
0
0
0
1
SW Data
Item
NO. No.
1
OC scan size default
setting
S
W
82
S
W
83
S
W
84
S
W
85
S
W
86
S
W
87
S
W
88
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
Switch selection and contents of functions
Bit No.
LETTER
LEGAL
A4
1
0
0
0
0
2
0
0
0
0
3
0
0
1
1
4
0
1
0
1
Initial value
LETTER
Inhibited to use
Binary input
Bit No.
Set range
3 4 5 6 7 8
Pattern No. 1 to 35
Refer to User program
“OC SIZE PRIORITY”.
0 When a value outside
0 the set range is set,
the initial value is set.
1
0
0
0
0
0
0
0 When a value outside
0 the set range is set,
0 the initial value is set.
0
Inhibited to use
Speaker sound volume
setting pattern number
Remark
1
Inhibited to use
Inhibited to use
Inhibited to use
Inhibited to use
Inhibited to use
FO-DC550 TEST COMMAND, FAX SOFT SWITCH, TROUBLE CODES 10 - 54
0
0
1
0
0
0
0
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
0
0
0
1
1
0
1
0
0
0
0
0
0
0
0
SW Data
Item
NO. No.
1
Inhibited to use
2
3
S
4
W
5
89
6
7
8
1
Inhibited to use
2
3
S
4
W
5
90
6
7
8
1
Symbol speed 3429
send enable in V.34
send
2
Symbol speed 3200
high carrier send enable
in V.34 send
3
Symbol speed 3200 low
carrier send enable in
V.34 send
4
Symbol speed 3000
S
high carrier send enable
W
in V.34 send
91
5
Symbol speed 3000 low
carrier send enable in
V.34 send
6
Symbol speed 3429
enable in V.34 send
7
Symbol speed 2800
enable in V.34 send
8
Symbol speed 2743
enable in V.34 send
1
Inhibited to use
2
3
S
4
W
5
92
6
7
8
1
Inhibited to use
2
3
S
4
W
5
93
6
7
8
1
Inhibited to use
2
3
S
4
W
5
94
6
7
8
Switch selection and contents of functions
Initial value
Remark
0
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1: Enable
1: Enable
1: Enable
1: Enable
1: Enable
0: Disable
Enable
1
Enable
1
Enable
1
Enable
1
Enable
1
Enable
1
Enable
1
Enable
1
0: Disable
0: Disable
0: Disable
0: Disable
1: Enable
0: Disable
1: Enable
0: Disable
1: Enable
0: Disable
FO-DC550 TEST COMMAND, FAX SOFT SWITCH, TROUBLE CODES 10 - 55
0
1
0
1
1
0
0
0
0
1
0
1
1
0
0
0
0
1
0
1
1
0
0
0
SW Data
NO. No.
1
2
3
S
4
W
5
95
6
7
8
1
2
3
S
4
W
5
96
6
7
8
1
2
3
S
4
W
5
97
6
7
8
1
2
3
S
4
W
5
98
6
7
8
1
2
3
S
4
W
5
99
6
7
8
1
2
3
S
4
W
5
100
6
7
8
1
2
3
S
4
W
5
101
6
7
8
Item
Switch selection and contents of functions
Initial value
Inhibited to use
Inhibited to use
Inhibited to use
Inhibited to use
Inhibited to use
Inhibited to use
Print effective image
area sub scan lead
edge void (Back
surface)
Binary input
Bit No.
Set range
Print effective image
Binary input
area sub scan rear edge
Bit No.
void (Back surface)
Set range
1 2 3 4
0 to 240 lines
16 line interval (600dpi)
5 6 7 8
0 to 240 lines
16 line interval (600dpi)
32 lines
48 lines
FO-DC550 TEST COMMAND, FAX SOFT SWITCH, TROUBLE CODES 10 - 56
Remark
0
1
1
1
0
0
0
0
1
1
0
1
1
0
0
0
0
1
1
1
1
1
1
1
0
1
0
0
0
0
0
0
0
1
0
1
1
0
0
0
1
0
0
0
0
0
0
0
0
0
1
0
0
0
1
1
SW Data
NO. No.
1
2
3
S
4
W
5
102
6
7
8
1
2
3
S
4
W
5
103
6
7
8
1
2
3
S
4
W
5
104
6
7
8
1
2
3
S
4
W
5
105
6
7
8
1
2
3
S
4
W
5
106
6
7
8
1
2
3
S
4
W
5
107
6
7
8
1
2
3
S
4
W
5
108
6
7
8
Item
Switch selection and contents of functions
Scan effective image
area main scan left
edge image loss (OC)
Binary input
Bit No.
Set range
Scan effective image
area main scan right
edge image loss (OC)
Binary input
Bit No.
Set range
Scan effective image
area sub scan lead
edge image loss (OC)
Binary input
Bit No.
Set range
Scan effective image
Binary input
area sub scan rear edge
Bit No.
image loss (OC)
Set range
Scan effective image
area main scan left
edge image loss (SPF
back surface)
Binary input
Bit No.
Set range
Scan effective image
area main scan right
edge image loss (SPF
back surface)
Binary input
Bit No.
Set range
Scan magnification ratio 1: –
adjustment (OC main
Binary input
scan)
Bit No.
Set range
Scan magnification ratio 1: –
adjustment (OC sub
Binary input
scan)
Bit No.
Set range
Scan magnification ratio 1: –
adjustment (SPF back Binary input
surface main scan)
Bit No.
Set range
Scan magnification ratio 1: –
adjustment (SPF back Binary input
surface sub scan)
Bit No.
Set range
Initial value
1 2 3 4
0 to 360 dots
24 dot interval
96 dots
5 6 7 8
0 to 360 dots
24 dot interval
96 dots
1 2 3 4
0 to 240 line
16 line interval
96 lines
5 6 7 8
0 to 240 line
16 line interval
144 lines
1 2 3 4
0 to 360 dots
in the interval of 24 dots
5 6 7 8
0 to 360 dots
in the interval of 24 dots
0: +
2 3 4 5 6
0 to ±12.7%
0.1% interval
7
8
0%
+
7
8
0%
0: +
2 3 4 5 6
0 to ±12.7%
0.1% interval
+
7
8
0%
0: +
2 3 4 5 6
0 to ±12.7%
0.1% interval
96 dots
+
0: +
2 3 4 5 6
0 to ±12.7%
0.1% interval
96 dots
+
7
8
0%
FO-DC550 TEST COMMAND, FAX SOFT SWITCH, TROUBLE CODES 10 - 57
Remark
0
1
0
0
0
1
0
0
0
1
1
0
1
0
0
1
0
1
0
0
0
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
SW Data
NO. No.
1
2
3
S
4
W
5
109
6
7
8
1
2
3
S
4
W
5
110
6
7
8
Item
Switch selection and contents of functions
Print magnification ratio 1: –
adjustment (Main scan Binary input
back surface)
Bit No.
Set range
Print magnification ratio 1: –
adjustment (Sub scan
Binary input
back surface)
Bit No.
Set range
Initial value
0: +
+
2 3 4 5 6
0 to ±12.7%
0.1% interval
7
8
0%
0: +
+
2 3 4 5 6
0 to ±12.7%
0.1% interval
7
8
0%
Remark
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
7. Soft switch descriptions
SW1 No.1, No.2 Image quality priority selection
SW4 No.1–No.4 Recall interval in communication error
Used to select the image quality setting when pressing C/A key or during auto clear.
Used to set the interval for recall when communication is cut off by an
error during memory send. (Including no response from the remote
machine.)
Default: 0 0 (Normal)
Setting is made in binary input.
SW1 No.3 Inhibited to use
SW1 No.4 Auto/Manual default setup
When set to 0, resend is mad immediately after completion of communication.
Used to select Auto/Manual reception mode when turning on the
power.
However, the time interval set by SW21 "Interval between completion
of communication and the next call" is valid.
Default: 0 (Automatic reception)
Default: 1min
SW1 No.5 Send request protection
SW4 No.5–No.8 Recall interval in busy
Used to set enable/disable of the confidential function (inhibit to send
to erroneous destinations) in send request communication (remote
send).
Used to set the interval for the next call when busy tone is detected in
communication.
The confidential function is performed by collating the number registered in this machine and the number registered in the remote
machine.
Setting is made in binary input.
Default: 3min
SW5 No.1, No2 Inhibited to use
Sender number ↔ Send request allow number
SW5 No.3, No.4 G3 send data accumulation wait time
Default: 0 (Protected)
Used to set wait time for accumulation of image data before sending
image data directly.
SW1 No.6–No.8 Inhibited to use
SW2 No.1–No.4 Inhibited to use
SW2 No.5–No.8 Remote selection number setup
Used to set the number in binary input for remote switch receive from
external telephone.
Default: 0 0 (6sec)
SW5 No.5–No.8 Pause time setup
Used to set pause time when registering dials.
Default: 2sec
However, "∗" in the remote switch number (X∗∗) is fixed.
SW6 No.1 ECM
Default: 5
Used to set YES/NO of error resend mode.
SW3 No.1–No.5 Density default setup
When, however, SW43-1 (V.34 mode function) is OFF or when SW341 (V.34 mode function) is ON and send is made other than SG3, ECM
setting of "NO" is valid.
Used to set the density when pressing C/A key or during auto clear.
Default: 0 0 1 0 0 (Medium)
SW3 No.6 Inhibited to use
SW3 No.7, No.8 Size specification
Used to set the size specification (AB series, inch series).
Under setting of "Follow information from machine," when command
information from the machine is uncertain, set this item to AB series.
Default: 0 1 (Conforms to the machine information.)
Since the ECM function is essential in V.34 mode and the remote
machine may perform checking, when SW43-1 (V.34 mode function) is
ON , this function is invalid in reception.
Default: 1 (Yes)
SW6 No.2 CED signal send
Used to set YES/NO of CED signal send.
This is valid only when SW52-7 (V.34 mode function) is OFF.
This is because ANSam signal send is necessary for V.34 mode.
When set to 1, CED signal send is performed.
When set to 0, CED signal send is not performed.
Default: 1 (Yes)
FO-DC550 TEST COMMAND, FAX SOFT SWITCH, TROUBLE CODES 10 - 58
SW6 No.3 CSI transmission
SW8 No.2 Proxy reception
Used to set YES/NO of CSI signal send.
Used to set whether proxy reception is enabled or not.
CSI signal includes the sender's number.
When set to 0, under the following error status, auto receive is not
made in auto receive mode.
Default: 1 (Yes)
SW6 No.4 DIS reception confirmation in G3 send
Used to set YES/NO of DIS receive check in G3 mode send.
When set to 1, DIS receive twice is checked.
When set to 0, DIS once is checked when "NSF/DIS" is received; and
DIS twice is checked when NSF is not received.
Default: 0 (Once in NFS reception, 2 time in DIS reception)
• Cover open
• Unit error (Toner, drum, developing-related errors)
• Recording paper JAM
• Document JAM
• Recording paper empty
When set to 1, proxy reception is allowed.
Default: 1 (Yes)
SW6 No.5 Inhibited to use
SW6 No.6 EOL detection timer
SW8 No.3 Inhibited to use
Used to set detection timer of EOL (EndOfLine) in Phase C receive.
SW8 No.4 Quick online send
Default: 0 (13sec)
Used to set whether quick online send function is enabled or not.
SW6 No.7 Countermeasure for echo in reception (CED
tone send interval)
Used to set the interval from CED send to FSK signal send of DIS.
When set to 0, send in memory mode ON is made in memory send.
When set to 1, send in memory mode ON is made in quick online send.
Default: 1 (Yes)
Default: 0 (75ms)
SW8 No.5 Remote select function
SW6 No.8 Countermeasure for echo in transmission (After
reception of DIS, hold time up to signal send is set.)
Used to set whether remote select function is enabled or not.
Used to set the interval from DIS receive to DSC signal send.
SW8 No.6–No.8 Number of times of CNG detection
Default: 0 (200ms)
Used to set the number of times of CNG detection for judgment of
detection.
SW7 No.1 Inhibited to use
Default: 1 (Yes)
Default: 3 times
SW7 No.2 Dial tone detection
Used to set whether dial tone is detected or not when calling out.
When set to 1, dial tone is detected before calling out.
When set to 0, dial tone is not detected and dialing is made after a certain time (3.5sec).
Default: 0 (No)
SW7 No.3 Busy tone detection
SW9 No.1 Print of total communication time and total
pages
Used to set whether the total communication time and total pages are
printed on the communication report or not.
When set to 1, the total communication time and total pages are
printed on the communication report.
Used to set YES/NO of busy tone detection when calling out.
When set to 0, the total communication time and total pages are not
printed on the communication report.
Default: 1 (Yes)
Default: 1 (Yes)
SW7 No.4 Dial tone monitoring time
SW9 No.2 Inhibited to use
Used to set the monitoring time when detecting dial tone.
SW9 No.3–No.8 Ringing volume pattern number
Default: 0 (5sec)
Used to set ringing volume pattern.
SW7 No.5 Inhibited to use
Default: 7
SW7 No.6 Max. length of reception
SW10 No.1 Measurement of communication time (image)
Used to set max. length of reception for long document.
Used to set YES/NO of measurement of communication time in phase
C. It is the communication time in the latest phase C. (Unit: msec)
Default: 0 (1.5m)
SW7 No.7, No.8 Destination display time when one-touch
key is pressed
Used to set the time from displaying the destination to the next operation in one-touch dial or reduction dial.
Default: 0 0 (2sec)
SW8 No.1 Memory transmission/direct transmission
default setup
Used to set whether memory send is ON or direct send is made (OFF)
in the memory mode when pressing C/A key or auto clear.
Default: 0 (Memory transmission)
Valid only in ECM communication.
Default: 1 (Yes)
SW10 No.2 Sender's telephone number registration
Used to set whether registered sender's telephone number can be
changed or not.
Default: 0 (Allow)
SW10 No.3–No.5 Inhibited to use
SW10 No.6 ECM byte/frame
Used to set the frame size of error correction mode to be notified to the
remote machine.
Default: 0 (256 [bytes/frame])
SW10 No.7, No.8 Inhibited to use
SW11 No.1–No.8 Scanner resource holding time out in
direct send
Used to set time-out time to hold scanner resource in direct send.
Default: 26sec
FO-DC550 TEST COMMAND, FAX SOFT SWITCH, TROUBLE CODES 10 - 59
SW12 No.1–No.4 Call time setup in automatic
transmission (T0 timer setup)
Used to set call time in automatic send.
Setting is made by binary input of N into "(5sec x N) + 30sec" in the
increment of 5sec.
Default: 45sec
SW17 No.4 ECM JBIG (Except for SG3)
Used to set whether JBIG coding capacity is allowed or not in communication other than SG3.
Default: 1 (Yes)
SW17 No.5 Inhibited to use
SW17 No.6 MH fixed (in SG3)
SW12 No.5 Inhibited to use
SW12 No.6, No.7 CI detection
Used to set whether coding capacity is fixed to MH or not in SG3 communication.
Used to set the detection frequency of CI signal (call signal).
Default: 0 (No)
Default: 0 0 (4 sine wave)
SW17 No.7 ECM MMR (in SG3)
SW12 No.8 Inhibited to use
Used to set whether MMR coding capacity is allowed or not in SG3
communication.
SW13 No.1, No.2 Inhibited to use
SW13 No.3, No.4 Ringing volume
Used to set the ringing volume when call-in.
Default: 1 (Yes)
SW17 No.8 ECM JBIG (in SG3)
Default: 1 0 (Medium)
Used to set whether JBIG coding capacity is allowed or not in SG3
communication.
SW13 No.5, No.6 Speaker volume in DTMF send
Default: 1 (Yes)
Used to set the volume of transmission and DTMF sound from the
speaker when SPEAKER key is pressed.
SW18 No.1–No.8 Inhibited to use
Default: 1 0 (Medium)
SW19 No.1–No.5 Inhibited to use
SW13 No.7, No.8 Inhibited to use
SW19 No.6 Recording table automatic print
SW15 No.1 Busy tone detection time (Lower limit)
Used to set whether communication report is automatically outputted
or not when the number of send/receive items which have not outputted yet on communication report reaches 50.
Used to set the lower limit of busy tone detection time (ON time).
When set to 1, they are automatically outputted.
Default: 0 (250ms)
When set to 0, they are not outputted even the number of items
reaches 50.
SW14 No.1–No.8 Inhibited to use
SW15 No.2 Busy tone detection time (Upper limit)
Used to set the upper limit of busy tone detection time (ON time).
Default: 0 (No)
Default: 0 (750ms)
SW19 No.7, No.8 Inhibited to use
SW15 No.3 Busy tone detection time (Lower limit 2)
SW20 No.1, No.2 Line sound monitor range
Used to set the lower limit 2 of busy tone detection time (ON time).
Used to set line sound monitor range when line sound monitor function
is used.
Default: 0 (Follows SW15-1.)
SW15 No.4–No.8 Signal send level
Used to set signal send level from MODEM.
Setting is made in binary input in the increment of 1dBm.
Default: –12dBm
Default: 0 0 (OFF)
SW20 No.3 Line monitor display
Used to set whether the communication speed and the receive level
are displayed on LCD or not.
Default: 0 (No)
SW16 No.1–No.4 Modem speed (V.33 mode or less)
Used to set send start speed in communication other than V.34 mode.
In an area of poor communication conditions, it is recommended to set
communication speed to a lower level in advance.
SW20 No.4 Inhibited to use
SW20 No.5 Receivable memory capacity
Used to set the remained memory capacity for allowing call-in.
Default: 1 0 0 0 (V.17 14.4kbps)
Default: 0 (128Kbyte)
SW16 No.5, No.6 Modem speed in reception fixed
SW20 No.6–No.8 Inhibited to use
Used to set receive procedure start speed in a remote machine other
than V.34.
SW21 No.1–No.8 Interval between completion of
communication and the next call
In setting of no fixing, the operations are the same as V.17-14400BPS.
Default: 0 0 (No fixing)
Used to set the interval between completion of communication and the
next call.
SW16 No.7, No.8 Inhibited to use
Setting is made in binary input.
Default: 1sec
SW17 No.1 Inhibited to use
SW17 No.2 MH fixed (Except for SG3)
Used to set whether coding capacity is fixed to MH or not in communication other than SG3.
Default: 0 (No)
SW22 No.1–No.8 Inhibited to use
SW23 No.1–No.8 Inhibited to use
SW24 No.1, No.2 Inhibited to use
SW17 No.3 ECM MMR (Except for SG3)
SW24 No.3, No4 Specified number reception (ANTI JUNK
FAX)
Used to set whether MMR coding capacity is allowed or not in communication other than SG3.
Used to set whether the FAX receive rejection function is made valid or
not for registered FAX numbers.
Default: 1 (Yes)
Default: 0 0 (Not set.)
SW24 No.5 Inhibited to use
FO-DC550 TEST COMMAND, FAX SOFT SWITCH, TROUBLE CODES 10 - 60
SW24 No.6 Document output setup in reception
SW30 No.2–No.4 Inhibited to use
Used to set the document output procedure; whether all the received
documents are collectively outputted after completion of reception or
every page is outputted when it is received.
SW30 No.5 Default data, sender print
Default: 0 (Output after reception of every page)
Used to set whether sender information (registered in the sender registration), sending date, and time are printed on the upper edge of send
document or not.
SW24 No.7 Inhibited to use
Default: 1 (ON)
SW24 No.8 Automatic reduction print
SW30 No.6 Inhibited to use
Used to set whether automatic reduction print is performed or not so
that a document longer than the fixed size and smaller than the automatic reduction line number setting is printed on fixed size paper.
SW30 No.7 Date/sender print position setup
Default: 1 (Allow)
Used to set whether date/sender information is printed inside the document area or outside the document area.
Default: 0 (Outside of document)
SW25 No.1–No.4 Automatic reduction rate setup
Used to set automatic reduction rate when automatic reduction print is
valid.
SW30 No.8 Inhibited to use
SW31 No.1, No.2 Report output (in transmission)
SW25 No.5, No.6 Transmission end sound tone
Used to set whether communication report is outputted or not after
completion of sending (excluding sequential broadcast and sequential
send request).
Used to set transmission end sound tone in transmission.
Default: 1 0 (Only when transmission is failed.)
Default: 10%
Default: 0 1 (1000Hz)
SW25 No.7, No.8 Reception end sound tone
Used to set reception end sound tone in reception.
Default: 0 1 (1000Hz)
SW26 No.1 Read completion sound
Used to set whether buzzer sound is made or not when scan is completed.
SW31 No.3, No.4 Report output (In broadcast and
sequential send request)
Used to set whether communication report is outputted or not after
completion of sending (sequential broadcast and sequential send
request).
Default: 0 1 (All print)
SW31 No.5, No.6 Report output (in reception)
In manual send or when scan is completed in direct send, buzzer
sound is not made.
Used to set whether communication report is outputted or not in reception.
Default: 0 (1sec)
Default: 0 0 (Print inhibited)
SW26 No.2 Inhibited to use
SW31 No.7, No.8 Contents of send document are printed
in memory send
SW26 No.3, No.4 Speaker volume setup
Used to set speaker volume.
The following sounds are the targets of this setting.
• Alarm sound
Used to set whether part of send document is printed on the communication report or not in memory send.
Default: 1 0 (Only the address to which transmission is failed)
• Send end sound
SW32 No.1–No.4 Distinctive ringing
• Receive end sound
Used to set the ringing pattern as FAX reception.
• Scan end sound
Default: 0 0 0 0 (OFF)
Default: 0 1 (Small)
SW32 No.5 Inhibited to use
SW26 No.5–No.8 Inhibited to use
SW32 No.6 Index print setup
SW27 No.1–No.6 Inhibited to use
Used to set whether the index is printed when outputting received document or not.
SW27 No.7, No.8 Recording paper tray selection
Used to select the recording paper tray used by FAX.
Valid only when two cassettes are installed.
Default: 0 (Not print)
SW32 No.7, No.8 Inhibited to use
Default: 0 0 (AUTO)
SW33 No.1 Page number print setup
SW28 No.1–No.8 Inhibited to use
Used to set whether the page number is added to the sender information print or not.
SW29 No.1–No.4 Number of auto switch calls of manual
reception → auto reception
Default: 1 (Yes)
Used to set the number of calls to switch to auto receive in manual
receive mode.
SW33 No.8 Reception data duplex print
SW33 No.2–No.7 Inhibited to use
When set to 0, switch to auto receive is not made.
Used to set whether duplex print of received data is made or not.
Default: 0 time
Default: 0 (No)
SW29 No.5–No.8 Setup of number of times of call rings
SW34 No.1–No.4 Inhibited to use
Used to set the number of calls before starting reception in auto
receive mode.
SW34 No.5–No.8 Signal send level Max.
Setting is made in binary input.
Default: –8dBm
Default: 2 times
SW30 No.1 Report output when canceling
Used to set whether the user cancel report is outputted or not when
send is canceled during document send.
Default: 0 (Not output)
Used to set the max. signal send level.
SW35 No.1 Cover function default setup
Used to set whether cover is added as default or not.
When auto clear is made by pressing C/A key, the machine returns to
this setting.
Default: 0 (No)
FO-DC550 TEST COMMAND, FAX SOFT SWITCH, TROUBLE CODES 10 - 61
SW35 No.2 Answering telephone connection
SW42 No.1 Direct send recall
Used to set whether the functions of answering telephone connection
mode are enabled or not.
Used to set whether direct send recall wait is allowed or not.
Default: 1 (Yes)
SW42 No.2 FAX receive auto select by CNG detection
SW35 No.3, No.4 CI delete max. OFF time
Used to set whether FAX receive auto select is enabled or not when
CNG signal is detected with external telephone used.
Used to set the max. wait time between detection of CI signal pulse
(number of times) and detection of the next CI signal pulse.
If CIK signal pulse is not detected within this time, the number of calls
up to that time is cleared.
Default: 0 0 (5sec)
SW35 No.5–No.8 Answering machine call number setting
Default: 0 (Allow)
Default: 1 (Allow)
SW42 No.3 Auto receive select in answering telephone
connection mode
Used to set whether auto receive select function in answering telephone connection mode is enabled or not.
Used to set the number of calls to switch to auto receive when answering telephone is not called in when the receive mode is set to the
answering telephone connection mode.
Default: 0 (Inhibit)
Setting is made in binary input.
SW42 No.8 V.34 mode function in manual communication
Default: 5 times
Used to set whether V.34 mode is enabled or not in manual communication.
SW36 No.1–No.8 CNG/mute detection completion time
Used to set the time for completion of CNG signal/mute detection in the
answering telephone connection mode.
Count is made from the last call signal.
SW42 No.4–No.7 Inhibited to use
When, however, SW43-1 is set to "0: OFF," V.34 mode is disabled
even tough this switch is set to "1: ON."
Default: 1 (ON)
Setting is made in binary input.
SW43 No.1 V.34 mode function
Default: 45sec
Used to set whether V.34 mode is enabled or not as a capacity of own
machine in send/receive.
SW37 No.1–No.4 Silence detection start time
Default: 1 (ON)
Used to set the time between reception of external telephone and
detection of mute in the answering telephone connection mode.
SW43 No.2 Busy tone detection level table
Default: 5sec
Used to set the busy tone detection level table.
SW37 No.5–No.8 Mute judgment time
Used set the mute judgment time when mute is continued for several
seconds.
Default: 0 (constant (ROM))
SW43 No.3 V.34 primary channel return mode
Used to set V.34 primary channel return mode.
Default: 5sec
Default: 1 (PPh)
SW38 No.1, No.2 Protocol monitor
SW43 No.4–No.6 Symbol speed mask in V.34 receive
Used to set whether communication protocol result is printed or not
after completion of communication.
Used to set symbol speed mask in V.34 receive.
Default: 0 0 (Not printed.)
SW43 No.7 Silence detection level table
SW38 No.3 Protocol monitor save
Used to set the mute detection level table.
Used to set whether the protocol monitor of the last communication is
saved or not. When set to "Saved," the previous protocol monitor can
be printed with SIM 66-21.
Default: 0 (constant (ROM))
Default: 1 (Yes)
SW38 No.4–No.8 Inhibited to use
Default: 1 0 1 (3429)
SW43 No.8 Control channel retrain judgment in V.34
reception
Used to set control channel retrain judgment in V.34 reception.
Default: 0 (Judge EQM value)
SW39 No.1–No.3 Inhibited to use
SW44 No.1–No.4 V.34 primary channel send speed
SW39 No.4–No.8 DTMF signal send time
Used to set send start speed in V.34 send.
Used to set DTMF signal send time.
Setting is made in binary input of N in "2400 (bps) x N" in the range of
2400bps – 33600bps.
Setting is made in binary input by the increment of 10ms.
Default: 110ms
SW40 No.1–No.8 Number of times of recall in error
Used to set the number of times of recall when a communication error
occurs.
N is set in the range of 0 – 15. When set to 0, 2400bps; when set to 15,
33600bps.
When set to 2400bps, all of SW91 No. 1 – 8 must be set as "Disable".
Default: 33600bps
Setting is made in binary input.
SW44 No.5–No.8 V.34 primary channel receive speed
When set to 0, recall is not made.
Used to set receive start speed in V.34 receive.
Default: 1 times
Setting is made in binary input of N in "2400 (bps) x N" in the range of
2400bps – 33600bps.
SW41 No.1–No.8 Number of times of recall in busy
Used to set the number of times of recall when busy tone is detected
during transmission.
Setting is made in binary input.
When set to 0, recall is not made.
N is set in the range of 0 – 15. When set to 0, 2400bps; when set to 15,
33600bps.
When set to 2400bps, all of SW43 No. 4 – 6 must changed to 2400.
Default: 33600bps
Default: 2 times
FO-DC550 TEST COMMAND, FAX SOFT SWITCH, TROUBLE CODES 10 - 62
SW45 No.1 FAST mode
SW48 No.3 Telephone line menu
Used to set whether FAST function is enabled or not.
Used to set whether tone/pulse setting is displayed on the menu or not.
Default: 0 (No)
Default: 0 (Allow)
SW45 No.2, No.3 Sequence of year/month/day in LCD,
report, and sender record
SW48 No.4 DP dial pulse number process
Used to set the sequence of year/month/day in LCD, report, and
sender record.
Default: 0 (Normal (N))
Used to set pulse number process in pulse dial.
Default: 0 1 (Month/Day/Year)
SW48 No.5–No.8 Scan effective image area main scan left
edge image loss (SPF)
SW45 No.4 Time display format
Used to set image loss of scan effective area.
Used to set time display format in LCD, report, and sender record.
Image loss on the left edge in SPF main scan direction can be
adjusted. When the set value is increased, image loss is increased.
Default: 1 (am/pm)
SW45 No.5–No.8 Scan effective image area main scan
right edge image loss (SPF)
Setting is made in binary input in the increment of 24 dots.
Used to set image loss of scan effective area.
SW49 No.1, No.2 Inhibited to use
Image loss on the right edge in SPF main scan direction can be
adjusted. When the set value is increased, image loss is increased.
SW49 No.3–No.8 Speaker sound volume pattern number
in DTMF send
Setting is made in binary input in the increment of 24 dots.
Default: 96 dots
Default: 96 dots
Used to set sound volume pattern in DTMF send.
Default: 21
SW46 No.1 Specification of print sequence in duplex print
Used to set the print sequence in duplex print of received data.
When set to 1, an odd-number page is printed after printing the next
even-number page. (214365...)
When set to 0, print is made in the ordinary reception order. (123456...)
Default: 1 (Print order (214365...))
SW46 No.2 Specification of rotating direction duplex back
surface print
Used to set whether the back surface is rotated 180 degrees in duplex
print or not.
SW50 No.1, No.2 Line monitor volume
Used to set on-hook monitor volume and line volume in FAX communication.
Default: 1 0 (Medium)
SW50 No.3–No.8 Line monitor volume pattern number
Used to set line monitor volume pattern.
Default: 16
SW51 No.1–No.5 DTMF send level (High group) setup
Used to set high-group send level in DTMF signal send.
When set to 1, the back surface is rotated 180 degrees and printed.
Setting is made in binary input in the increment of 1.0dBm.
When set to 0, the back surface is not rotated and printed.
Default: –6dBm
Default: 1 (180 degrees rotation)
SW51 No.6 CED detection time
SW46 No.3 Priority in the day of week
Used to set detection time of CED/ANSam signal for judgment of
detection.
Used to set which is indicated first, day or day of week, when date format is in the sequence of day, month, and year.
Default: 1000ms
When set to 1, day of week is indicated first, and then day is indicated.
SW51 No.7, No.8 Busy tone detection cycle
When set to 0, day is indicated first, and then day of week is indicated.
Default: 0 (No)
Used to set detection cycle of pulses of busy tone for detection of busy
tone.
SW46 No.4 Center No. in FAST mode
Default: 0 0 (2puls)
Used to set which is set as FAST center number, Service-No or HostTel-No.
SW52 No.1, No.2 Busy tone detection level
Default: 0 (Service-No.)
Default: 0 0 (–43dB)
SW46 No.5 Summer time
SW52 No.3 Inhibited to use
Used to set whether summer time function is enabled or not.
SW52 No.4 Super G3 disabled in the last call-out of recall
in case of an error
When set to 1, summer time function is enabled.
When set to 0, summer time function is disabled.
Default: 0 (Inhibit)
SW46 No.6–No.8 Inhibited to use
SW47 No.1 Inhibited to use
Used to set the mini. Detection level in busy tone detection.
Used to set whether Super G3 is disabled or not in the last call-out of
recall in case of a send error.
When, however, the number of recall in case of a send error is 0, this
function does not operate.
Default: 0 (Super G3 disabled)
SW47 No.2 External telephone connection
Used to set whether external telephone is used or not.
This switch must be set to YES in order to use external telephone.
Default: 1 (Yes)
SW52 No.5 Error process in RTN reception
Used to set whether RTN reception is judged as an error or not. (Only
in G3 mode)
When set to 1, RTN reception is not judged as an error.
SW47 No.3–No.8 Inhibited to use
When set to 0, RTN reception is judged as an error.
SW48 No.1, No.2 Tone/Pulse default setup
Default: 0 (Error)
Used to set the dial type.
SW52 No.6, No.7 Inhibited to use
Default: 1 0 (TONE)
FO-DC550 TEST COMMAND, FAX SOFT SWITCH, TROUBLE CODES 10 - 63
SW52 No.8 V.34 control channel communication speed
SW57 No.4–No.8 Reception gain adjustment
Used to set control channel communication speed in V.34 mode.
Used to set reception gain correction.
If the remote machine does not make 2400bps enable, the speed is
always 1200bps.
Setting is made in binary input in the increment of 0.5dBm.
Default: 0 (1200bps)
SW58 No.1–No.4 Dual wait inhibit time after CFR send
SW53 No.1–No.4 Maximum DTMF send level
Used to set dual wait inhibit time after CFR send.
Used to set the max. send level of DTMF signal.
Setting is made in binary input in the increment of 200ms.
Setting is made in binary input in the increment of 1.0dBm.
Default: 1600ms
Default: 0dBm
SW58 No.5–No.8 FSK signal settlement time in double
wait
SW53 No.5–No.8 DTMF send level (difference between
high and low level)
Used to set DTMF signal send level in low group by the difference from
that in high group.
Setting is made in binary input in the increment of 0.5dBm.
Default: +2.0dBm
SW54 No.1–No.4 Scan effective image area sub scan lead
edge image loss (SPF)
Default: 0.0dBm
Used to set FSK signal settlement time in double (dual) wait.
Setting is made in binary input in the increment of 50ms.
Default: 550ms (7)
SW59 No.1, No.2 Inhibited to use
SW59 No.3, No.4 Reception SED ON level
Used to set reception SED ON level.
Used to set image loss in scan image area.
Default: 1 1 (–48dB)
Image loss on the lead edge in SPF sub scan direction can be
adjusted. When the set value is increased, image loss on the lead
edge is increased.
SW59 No.5, No.6 Transmission cable amplitude equalizer
Setting is made in binary input in the increment of 16 lines.
Default: 96 lines
Used to set transmission cable amplitude equalizer.
Default: 0 0 (0dB)
SW59 No.7, No.8 Reception cable amplitude equalizer
Used to set reception cable amplitude equalizer.
SW54 No.5–No.8 Scan effective image area sub scan rear
edge image loss (SPF)
Used to set image loss in scan image area.
Image loss on the rear edge in SPF sub scan direction can be
adjusted. When the set value is increased, image loss on the rear edge
is increased.
Setting is made in binary input in the increment of 16 lines.
Default: 144 lines
Default: 0 0 (0dB)
SW60 No.1–No.4 Scan effective image area sub scan lead
edge image loss (SPF back surface)
Used to set image loss in scan image area.
Image loss on the lead edge in SPF bask surface sub scan direction
can be adjusted. When the set value is increased, image loss on the
lead edge is increased.
Setting is made in binary input in the increment of 16 lines.
SW55 No.1–No.7 CI signal OFF detection enable time
Used to set the min. OFF time for judgment of 1 pulse (1 call) of CI
(call-in signal).
If OFF time continues more than the set value, it is judged as 1 pulse.
Setting is made in binary input in the increment of 10ms.
Default: 96 lines
SW60 No.5–No.8 Scan effective image area sub scan rear
edge image loss (SPF back surface)
Used to set image loss in scan image area.
SW55 No.8 Inhibited to use
Image loss on the rear edge in SPF bask surface sub scan direction
can be adjusted. When the set value is increased, image loss on the
rear edge is increased.
SW56 No.1–No.3 CI signal ON detection enable time
Setting is made in binary input in the increment of 16 lines.
Used to set the min. ON time for judgment of 1 pulse (1 call) of CI (callin signal).
Default: 144 lines
If ON time continues more than the set value, it is judged as 1 pulse.
SW62 No.1 Inhibited to use
Default: 1200ms
Setting is made in binary input in the increment of 10ms.
Default: 155ms
SW61 No.1–No.8 Inhibited to use
SW62 No.2 CI signal ON time in V.8 mode
Used to set CI signal ON time in CI signal send in V8 mode.
SW56 No.4 Inhibited to use
Default: 0 (9byte (240ms))
SW56 No.5, No.6 DT/BT detection frequency range
Used to set DT/BT detection frequency range.
Default: 0 1 (420Hz–680Hz)
SW62 No.3 CI signal OFF time in V.8 mode
Used to set CI signal OFF time in CI signal send in V8 mode.
Default: 0 (1sec)
SW56 No.7, No.8 Inhibited to use
SW62 No.4, No.5 V.8 mode ANSam signal send time
SW57 No.1 Inhibited to use
Used to set ANSam/CED signal send time.
SW57 No.2 Sharp machine mode
Default: 0 1 (4sec)
Used to set whether communication is made in Sharp machine mode
or not.
SW62 No.6–No.8 Inhibited to use
Default: 1 (ON)
SW63 No.1, No.2 CI receive number to shift to non-V.34
communication
SW57 No.3 Inhibited to use
Used to set CI receive number to shift to non-V.34 communication.
Default: 1 0 (2 times)
FO-DC550 TEST COMMAND, FAX SOFT SWITCH, TROUBLE CODES 10 - 64
SW63 No.3–No.5 CI send number to shift to non-V.34
communication
SW72 No.6 Inhibited to use
Used to set CI send number to shift to non-V.34 communication.
Used to set CNG send time.
Setting is made in binary input.
Default: 0 0 (0.5sec)
Default: 2
SW63 No.6–No.8 Inhibited to use
SW72 No.7, No.8 CNG send start
SW73 No.1, No.2 Minimum flags between frames
Used to set minimum flag number between frames.
SW64 No.1–No.8 Inhibited to use
Default: 0 0 (2-flag)
SW65 No.1–No.8 Inhibited to use
SW73 No.3, No.4 Phase C head dummy data send time
SW66 No.1–No.8 Inhibited to use
Used to set phase C head dummy data send time.
SW67 No.1–No.4 Make time (10PPS) setup
Default: 0 0 (0.2sec)
Used to set make time in dialing in 10PPS.
SW73 No.5, No.6 Inhibited to use
Setting is made in binary input in the increment of 1ms.
SW73 No.7, No.8 Flag-adrs timer setup (V.21-FSK)
Default: 40ms
Used to set timer between Flag-adrs in FSK signal receive in communication other than V.34 mode.
SW67 No.5–No.8 Inhibited to use
SW68 No.1, No.2 Line open delay time in dial test
Used to set time interval between end of dialing and opening the line.
Valid only in dial test of simulation.
Default: 0 0 (2sec)
SW68 No.3, No.4 Inhibited to use
SW68 No.5–No.8 T1 timer setup
Used to set time for connection of the line when the remote machine
does not respond in FAX communication.
FSK signal receive in V.34 mode does not conform to this soft switch.
Default: 0 0 (6sec)
SW74 No.1–No.4 Print effective image area sub scan lead
edge void
Used to set print image area void.
The void amount on the lead edge in the sub scan direction can be
adjusted. When the set value is increased, the void amount on the lead
edge is increased.
Setting is made in binary input in the increment of 16 lines.
The time of ITU-T standard is 35 ± 5sec.
Default: 32 lines
Setting is made in binary input in the increment of 5sec.
SW74 No.5–No.8 Inhibited to use
Default: 40sec
SW69 No.1–No.8 Inhibited to use
SW70 No.1–No.3 Inhibited to use
SW70 No.4 Reception waiting time between frames
SW75 No.1, No.2 Inhibited to use
SW75 No.3, No.4 Communication end sound (Buzzer
sound length) setting
Used to set reception wait time between frames.
Used to set the length of communication end buzzer sound in communication.
Default: 0 (3.4sec)
Default: 0 0 (3sec)
SW70 No.5, No.6 Preamble send time of 300bps
Used to set preamble send time of 300bps.
SW75 No.5–No.8 Print effective image area main scan
void
Default: 0 1 (1.0sec)
Used to set void amount in print image area.
Used to set number of times of RCP frame send.
The void amount in the main scan direction can be adjusted. When the
set value is increased, the margins on the right and the left are
increased.
Default: 0 0 (3 times)
Setting is made in binary input in the increment of 16 dots.
SW71 No.1–No.8 Inhibited to use
Default: 48 dots
SW72 No.1 EYE-Q check
SW76 No.1–No.8 Scan magnification ratio adjustment
(SPF main scan)
SW70 No.7, No.8 RCP send times
Used to set TCF check in TCF reception.
When set to 1, check is made only with EYE-Q value (EQM value).
Therefore, TCF check is loosely made.
Used to set main scan magnification ratio in SPF scan.
When set to 0, check is made with received data and EYE-Q value
(EQM value).
Default: 0%
Setting is made in binary input in the increment of 0.1%.
Default: 0 (0 reception & EYE-Q check)
SW77 No.1–No.8 Scan magnification ratio adjustment
(SPF sub scan)
SW72 No.2 ERR frame reception operation
Used to set sub scan magnification ratio in SPF scan.
Used to set operations when an image with an error frame is received.
Setting is made in binary input in the increment of 0.1%.
Default: 0 (Not continue process. (Error))
Default: 0%
SW72 No.3, No.4 Waiting time for CED/ANSam send start
SW78 No.1–No.8 Print magnification ration adjustment
(main scan)
Used to set waiting time from when the line is connected and the
machine enters FAX receive state to when CED/ANSam signal is send
to the line.
Default: 0 0 (2.25sec)
Used to set main scan magnification ratio in print.
Setting is made in binary input in the increment of 0.1%.
Default: 0%
SW72 No.5 RTC EOL send times
Used to set number of times of RTC EOL send.
Default: 1 (6 times)
FO-DC550 TEST COMMAND, FAX SOFT SWITCH, TROUBLE CODES 10 - 65
SW79 No.1–No.8 Print magnification ration adjustment
(sub scan)
SW91 No.6 Symbol speed 3429 enable in V.34 send
Used to set sub scan magnification ratio in print.
Used to set whether use of 3429Hz is allowed or not as symbol speed
in V.34 send.
Setting is made in binary input in the increment of 0.1%.
Default: 1 (Enable)
Default: 0%
SW91 No.7 Symbol speed 2800 enable in V.34 send
SW80 No.1–No.8 Destination information
Used to set country code.
Used to set whether use of 2800Hz is allowed or not as symbol speed
in V.34 send.
Default: North America
Default: 1 (Enable)
SW81 No.1–No.8 Language information
SW91 No.8 Symbol speed 2743 enable in V.34 send
Used to set language.
Used to set whether use of 2743Hz is allowed or not as symbol speed
in V.34 send.
Default: American English
SW82 No.1–No.4 OC scan size default setting
Used to set OC scan default size.
Default: 1 (Enable)
SW92 No.1–No.8 Inhibited to use
Default: 0 0 0 1 (LETTER)
SW93 No.1–No.8 Inhibited to use
SW82 No.5–No.8 Inhibited to use
SW94 No.1–No.8 Inhibited to use
SW83 No.1, No.2 Inhibited to use
SW95 No.1–No.8 Inhibited to use
SW83 No.3–No.8 Speaker sound volume setting pattern
number
SW96 No.1–No.8 Inhibited to use
Used to set sound volume pattern of communication end and scan
end.
SW98 No.1–No.8 Inhibited to use
Default: 1
SW99 No.1–No.8 Inhibited to use
SW84 No.1–No.8 Inhibited to use
SW100 No.1–No.8 Inhibited to use
SW85 No.1–No.8 Inhibited to use
SW101 No.1–No.4 Print effective image area sub scan
lead edge void (Back surface)
SW86 No.1–No.8 Inhibited to use
SW87 No.1–No.8 Inhibited to use
SW88 No.1–No.8 Inhibited to use
SW89 No.1–No.8 Inhibited to use
SW97 No.1–No.8 Inhibited to use
Used to set void amount in print image area.
Void amount on the lead edge in sub scan direction can be adjusted.
When the set value is increased, the margin on the lead edge is
increased.
Setting is made in binary input in the increment of 16 lines.
SW90 No.1–No.8 Inhibited to use
Default: 32 lines
SW91 No.1 Symbol speed 3429 send enable in V.34 send
SW101 No.5–No.8 Print effective image area sub scan rear
edge void (Back surface)
Used to set whether symbol speed of 3429Hz is allowed or not in V.34
send.
Default: 1 (Enable)
SW91 No.2 Symbol speed 3200 high carrier send enable in
V.34 send
Used to set whether use of high carrier is allowed or not when symbol
speed of 3200Hz is selected in V.34 send.
Void amount on the rear edge in sub scan direction can be adjusted.
When the set value is increased, the margin on the read edge is
increased.
Setting is made in binary input in the increment of 16 lines.
Default: 48 lines
When high/low carriers are "disable", 3200Hz cannot be selected.
SW102 No.1–No.4 Scan effective image area main scan
left edge image loss (OC)
Default: 1 (Enable)
Used to set image loss in scan image area.
SW91 No.3 Symbol speed 3200 low carrier send enable in
V.34 send
Image loss on the left edge in OC main scan direction can be adjusted.
When the set value is increased, image loss is increased.
Used to set whether use of low carrier is allowed or not when symbol
speed of 3200Hz is selected in V.34 send.
Setting is made in binary input in the increment of 24 dots.
When high/low carriers are "disable", 3200Hz cannot be selected.
SW102 No.5–No.8 Scan effective image area main scan
right edge image loss (OC)
Default: 1 (Enable)
SW91 No.4 Symbol speed 3000 high carrier send enable in
V.34 send
Used to set whether use of high carrier is allowed or not when symbol
speed of 3000Hz is selected in V.34 send.
Default: 96 dots
Used to set image loss in scan image area.
Image loss on the right edge in OC main scan direction can be
adjusted. When the set value is increased, image loss is increased.
Setting is made in binary input in the increment of 24 dots.
When high/low carriers are "disable", 3200Hz cannot be selected.
Default: 96 dots
Default: 1 (Enable)
SW103 No.1–No.4 Scan effective image area sub scan
lead edge image loss (OC)
SW91 No.5 Symbol speed 3000 low carrier send enable in
V.34 send
Used to set image loss in scan image area.
Used to set whether use of low carrier is allowed or not when symbol
speed of 3000Hz is selected in V.34 send.
Image loss on the lead edge in OC sub scan direction can be adjusted.
When the set value is increased, image loss is increased.
When high/low carriers are "disable", 3200Hz cannot be selected.
Setting is made in binary input in the increment of 16 lines.
Default: 1 (Enable)
Default: 96 lines
FO-DC550 TEST COMMAND, FAX SOFT SWITCH, TROUBLE CODES 10 - 66
SW103 No.5–No.8 Scan effective image area sub scan
rear edge image loss (OC)
SW106 No.1–No.8 Scan magnification ratio adjustment
(OC sub scan)
Used to set image loss in scan image area.
Used to set the sub scan magnification ratio in OC sub scan.
Image loss on the rear edge in OC sub scan direction can be adjusted.
When the set value is increased, image loss is increased.
Setting is made in binary input in the increment of 0.1%.
Setting is made in binary input in the increment of 16 lines.
Default: 144 lines
SW107 No.1–No.8 Scan magnification ratio adjustment
(SPF back surface main scan)
SW104 No.1–No.4 Scan effective image area main scan
left edge image loss (SPF back surface)
Used to set the main scan magnification ratio in SPF back surface
scan.
Used to set image loss in scan image area.
Setting is made in binary input in the increment of 0.1%.
Image loss in SPF back surface main scan direction can be adjusted.
When the set value is increased, image loss is increased.
Default: 0%
Setting is made in binary input in the increment of 24 dots.
Default: 96 dots
Default: 0%
SW108 No.1–No.8 Scan magnification ratio adjustment
(SPF back surface sub scan)
Used to set the sub scan magnification ratio in SPF back surface scan.
SW104 No.5–No.8 Scan effective image area main scan
right edge image loss (SPF back surface)
Setting is made in binary input in the increment of 0.1%.
Used to set image loss in scan image area.
SW109 No.1–No.8 Print magnification ratio adjustment
(Main scan back surface)
Image loss on the right edge in SPF back surface main scan direction
can be adjusted. When the set value is increased, image loss is
increased.
Setting is made in binary input in the increment of 24 dots.
Default: 0%
Used to set the main scan magnification ratio in back surface print.
Setting is made in binary input in the increment of 0.1%.
Default: 0%
Default: 96 dots
SW105 No.1–No.8 Scan magnification ratio adjustment
(OC main scan)
Used to set the main san magnification ratio in OC main scan.
Setting is made in binary input in the increment of 0.1%.
SW110 No.1–No.8 Print magnification ratio adjustment
(Sub scan back surface)
Used to set the sub scan magnification ratio in back surface print.
Setting is made in binary input in the increment of 0.1%.
Default: 0%
Default: 0%
8. Trouble codes
A. Trouble codes list
B. Details of trouble codes
Main Sub
Details of trouble
code code
E1
00 IMC communication trouble
10 IMC trouble
13 IMC flash ROM error
16 IMC DIMM memory read/write check error
81 IMC communication interface error (parity)
82 IMC communication interface error (Overrun)
84 IMC communication interface error (Framing)
E7
02 LSU trouble
10 Shading trouble (Black correction)
11 Shading trouble (White correction)
16 Abnormal laser output
F2
04 Improper cartridge (Destination error, life cycle error)
F5
02 Copy lamp lighting abnormality
F6
10 FAX board trouble
H2
00 Thermistor open
H3
00 Heat roller high temperature detection
H4
00 Heat roller low temperature detection
L1
00 Feeding is not completed within the specified time after
starting feeding. (The scan head locking switch is locked)
L3
00 Scanner return trouble
L4
01 Main motor lock detection
L6
10 Polygon motor lock detection
U1
03 FAX board battery error
U2
04 EEPROM read/write error (Serial communication error)
11 Counter check sum error (EEPROM)
40 CRUM chip communication error
U9
99 Operation panel language error
Main Sub
Details of trouble
code code
E1
00 Content IMC communication trouble
Detail
An abnormality occurs in communication
between the CPU and the IMC.
Cause IMC – CPU signal line abnormality
IMC Memory defect/data abnormality
Check Replace the MCU PWB with new one.
and
remedy
10 Content IMC trouble
Detail
An abnormality occurs in the IMC.
Cause USB chip error/CODEC error on the IMC.
Check Replace the MCU PWB with a new one.
and
remedy
13 Content IMC flash ROM error
Detail
An abnormality occurs in the IMC flash ROM.
Cause IMC abnormality
Check Replace the MCU PWB with a new one.
and
If downloading of the program is abnormally
remedy terminated, it may cause an error. Download
the program again to avoid this.
FO-DC550 TEST COMMAND, FAX SOFT SWITCH, TROUBLE CODES 10 - 67
Main Sub
Details of trouble
code code
E1
16 Content IMC DIMM memory read/write check error
Detail
An installation error occurs in the IMC memory
module.
An error occurs during access to the IMC
memory.
Cause Improper installation of the IMC memory
module.
IMC memory module abnormality
IMC memory contact abnormality
IMC abnormality.
Check Check installation of the memory module.
and
Replace the memory module.
remedy Replace the MCU PWB with a new one.
81 Content IMC communication interface error (parity)
Detail
A parity error occurs in communication between
the CPU and the IMC.
Cause IMC memory defect/data abnormality
Check Check the memory of the IMC.
and
Replace the MCU PWB with new one.
remedy
82 Content IMC communication interface error (Overrun)
Detail
An overrun error occurs in communication
between the CPU and the IMC.
Cause IMC memory defect/data abnormality.
Check Check the memory of the IMC.
Replace the MCU PWB with new one.
and
remedy
84 Content IMC communication interface error (Framing)
Detail
A framing error occurs in communication
between the CPU and the IMC.
Cause IMC memory defect/data abnormality.
Check Check the memory of the IMC.
and
remedy
E7
02 Content LSU trouble
Detail
The BD signal from the LSU cannot be detected
in a certain cycle. (Always OFF or always ON)
Cause LSU connector or LSU harness defect or
disconnection
Polygon motor rotation abnormality
Laser beams are not generated.
MCU PWB abnormality.
Check Check connection of the LSU connector.
and
Execute TC 61-03 to check the LSU operations.
remedy Check that the polygon motor rotates normally.
Check that the laser emitting diode generates
laser beams.
Replace the LSU unit.
Replace the MCU PWB.
10 Content Shading trouble (Black correction)
Detail
The CCD black scan level is abnormal when the
shading.
Cause Improper connection of the CCD unit flat cable
CCD unit abnormality
MCU PWB abnormality
Check Check connection of the CCD unit flat cable.
and
Check the CCD unit.
remedy
Main Sub
Details of trouble
code code
E7
11 Content Shading trouble (White correction)
Detail
The CCD white scan level is abnormal when the
shading.
Cause Improper connection of the CCD unit flat cable
Dirt on the mirror, the lens, and the reference
white plate
Copy lamp lighting abnormality
CCD unit abnormality
MCU PWB abnormality
(When occurred in the SPF scan position.)
Improper installation of the mirror unit
Check Clean the mirror, lens, and the reference white
and
plate.
remedy Check the light quantity and lighting status of
the copy lamp (TC 05-03).
Check the MCU PWB.
16 Content Abnormal laser output
Detail
When the laser output is stopped, HSYNC is
detected.
Cause Laser abnormality
MCU PWB abnormality.
Check Check the laser emitting diode operation.
and
Replace the MCU PWB.
remedy
F2
04 Content Improper cartridge (Destination error, life cycle
error)
Detail
The destination of the main unit differs from that
of the CRUM.
The life cycle information is other than "FFh"
(Not used).
Cause CRUM chip trouble
Improper developing unit
Check Replace the CRUM chip.
and
Replace the developing unit.
remedy
F5
02 Content Copy lamp lighting abnormality
Detail
The copy lamp does not turn on.
Cause Copy lamp abnormality
Copy lamp harness abnormality
CCD PWB harness abnormality.
Check Use TC 5-3 to check the copy lamp operations.
and
When the copy lamp lights up.
remedy Check the harness and the connector between
the CCD unit and the MCU PWB.
When the copy lamp does not light up.
Check the harness and the connector between
the copy lamp unit and the MCU PWB.
Replace the copy lamp unit.
Replace the MCU PWB.
F6
10 Content FAX board trouble
Detail
Communication trouble between MCU and FAX
control PWB
Cause FAX control PWB connector disconnection
Defective harness between FAX control PWB
and MCU PWB
Motherboard connector pin breakage
FAX control PWB ROM error/Data error
IC on FAX PWB causes abnormality
Check Check connector/harness of FAX control PWB
and
and MCU PWB.
remedy Check the grounding of the copier.
Check FAX control PWB ROM.
Replace the FAX PWB.
FO-DC550 TEST COMMAND, FAX SOFT SWITCH, TROUBLE CODES 10 - 68
Main Sub
Details of trouble
code code
H2
00 Content Thermistor open
Detail
The thermistor is open.
The fusing unit is not installed.
Cause Thermistor abnormality
Control PWB abnormality
Fusing section connector disconnection
The fusing unit is not installed.
Check Check the harness and the connector between
and
the thermistor and the PWB.
remedy Use TC 14 to clear the self diagnostic display.
H3
00 Content Heat roller high temperature detection
Detail
The fusing temperature exceeds 240°C.
Cause Thermistor abnormality
Control PWB abnormality
Fusing section connector disconnection.
Check Use TC 5-02 to check the heater lamp blinking
and
operation.
remedy When the lamp blinks normally.
Check the thermistor and its harness.
Check the thermistor input circuit on the control
PWB.
When the lamp keeps ON.
Check the power PWB and the lamp control
circuit on the MCU PWB.
Use TC 14 to clear the self diagnostic display.
H4
00 Content Heat roller low temperature detection
Detail
The fusing temperature does not reach 185°C
within 27 sec of turning on the power, or the
fusing temperature keeps at 140°C.
Cause Thermistor abnormality
Heater lamp abnormality
Thermostat abnormality
Control PWB abnormality
Check Use TC 5-02 to check the heater lamp blinking
and
operation.
remedy When the lamp blinks normally.
Check the thermistor and its harness.
Check the thermistor input circuit on the control
PWB.
When the lamp does not light up.
Check for disconnection of the heater lamp and
the thermostat. Check the interlock switch.
Check the power PWB and the lamp control
circuit on the MCU PWB.
Use TC 14 to clear the self diagnostic display.
Main Sub
Details of trouble
code code
L1
00 Content Feeding is not completed within the specified
time after starting feeding. (The scan head
locking switch is locked)
Detail
The white area and the black marking on the
shading plate are used to obtain the difference
in the CCD level values for judgment of lock.
When the difference in the levels of which and
black is small, it is judged that the black mark
could not be scanned by lock and the trouble
code “L1” is displayed.
Cause The scan head is locked by the lock switch.
Mirror unit abnormality
The scanner wire is disconnected.
The origin detection sensor abnormality
Mirror motor harness abnormality
Check Check to confirm that the scan head lock switch
and
is released.
remedy Use TC 1-1 to check the mirror reciprocating
operations.
When the mirror does not feed.
Check for disconnection of the scanner wire.
Check the harness and the connector between
the mirror motor and the MCU PWB.
Replace the mirror unit.
Replace the MCU PWB.
When the mirror does feed.
Use TC 1-2 to check the mirror home position
sensor.
L3
00 Content Scanner return trouble
Detail
When the mirror base is returned for the
specified time (6 sec) in mirror initializing after
turning on the power, the mirror home position
sensor (MHPS) does not turn ON. Or when the
mirror base is returned for the specified time
(about 6 sec) after start of copy return, the
mirror home position sensor (MHPS) does not
turn ON.
Cause Mirror unit abnormality
Scanner wire disconnection
Origin detection sensor abnormality
Mirror motor harness abnormality
Check Use TC 1-1 to check the mirror reciprocating
and
operations.
remedy When the mirror does not return.
Check for disconnection of the scanner wire.
Check the harness and the connector between
the mirror motor and the MCU PWB.
Replace the mirror unit.
Replace the MCU PWB.
When the mirror does feed.
Use TC 1-2 to check the mirror home position
sensor.
L4
01 Content Main motor lock detection
Detail
When the main motor encoder pulse is not
detected for 100 msec.
Cause Main motor unit abnormality
Improper connection or disconnection the main
motor and the harness.
MCU PWB abnormality
Check Use TC 25-01 to check the main motor
and
operations.
remedy Check connection of the main motor harness/
connector.
Replace the main motor.
Replace the MCU PWB.
FO-DC550 TEST COMMAND, FAX SOFT SWITCH, TROUBLE CODES 10 - 69
Main Sub
Details of trouble
code code
L6
10 Content Polygon motor lock detection
Detail
The lock signal (specified rpm signal) does not
return within a certain time (about 20 sec) from
starting the polygon motor rotation.
Cause Polygon motor unit abnormality
Improper connection or disconnection of the
polygon motor and the harness.
MCU PWB abnormality
Check Use TC 61-1 to check the polygon motor
and
operations.
remedy Check connection of the polygon motor
harness/connector.
Replace the polygon motor.
Replace the MCU PWB.
U1
03 Content FAX board battery error
Details The SRAM backup battery voltage on FAX
PWB falls.
Cause The SRAM backup battery voltage on FAX
PWB falls.
Check Check voltage of the SRAM back up battery.
and
Replace the battery.
remedy
U2
04 Content EEPROM read/write error (Serial
communication error)
Detail
EEPROM access process error
Cause EEPROM abnormality
Check Check that the EEPROM is properly set.
and
Use TC 16 to cancel the trouble.
remedy Replace the MCU PWB.
11 Content Counter check sum error (EEPROM)
Detail
Check sum error of the counter area in the
EEPROM
Cause EEPROM abnormality
Check Check that the EEPROM is properly set.
and
Use TC 16 to cancel the trouble.
remedy Replace the MCU PWB.
40 Content CRUM chip communication error
Detail
An error occurs in MCU-CRUM chip
communication.
Cause CRUM chip trouble
Defective contact of developing unit
MCU PWB trouble
Check Replace the CRUM chip.
Check installation of the developing unit.
and
remedy Cancel the operation with TC16.
Replace the MCU PWB.
U9
99 Content Operation panel language error
Detail
There is no language file.
The language file is destroyed.
Cause Language file abnormality
MCU PWB abnormality
Check MCU firmware download
and
Replace the MCU PWB.
remedy
9. Communication error codes
A. Error code identification
Communication error xx (xxxx)
(In print out, the communication error display is made. In FAX status
check, “NGxxxxxx” is displayed.
When transmission or reception is not executed normally due to disturbance in protocol signals and image signals by the trouble in the line,
the code of 6 digits is displayed on the transmission result check menu
(reception result check menu).
Upper 2 digits of a communication error code: 00 – 58 (error code) is
displayed. (Communication result code)
Lower 4 digits of a communication error code: Error code1, Error code
2
1) Refer to the communication result code.
2) Refer to error code 1.
3) Refer to error code 2.
(Error code 1 other than V.34 mode is “00”.)
<Communication result code>
Error code
(Communication
result)
0 – 31
Communication
report result
column
For details of 0 –
31, refer to the
communication
result code.
33
Busy
34
Cancel
35
Power OFF
36
(Recording paper
empty)
(Recording paper
jam)
Reception
memory over
(Discrepancy in
the number of
sheets)
(Interface not
accepted)
Transmission
length over
37
38
39
40
41
42
Reception length
over
43
Communication
(OK)
Document error
44
45
46
(Image quality
error)
No response from
the other party
FO-DC550 TEST COMMAND, FAX SOFT SWITCH, TROUBLE CODES 10 - 70
Communication interruption
content
Depends on the
communication
disconnection position.
For 16 or later, V.34 mode
communication.
The calling side cannot
connect the line with the
other party.
An interruption command is
made during transmission or
reception.
A reservation is canceled.
An interruption command is
entered with the interruption
key.
Power OFF during
transmission or reception
Memory over during
reception
The length of transmission
data of one page exceeds
the range during
transmission.
The length of reception data
of one page exceeds the
range during reception.
Communication enable
before transmission
A document jam during
direct transmission
The FAX signal from the
other party cannot detect
within T1 time.
Error code
(Communication
result)
47
48
49
Communication
report result
column
(Communication
error)
OK
No send request
function on the
other party
50
Send request not
accepted
51
Send request
enable number
discrepancy
52
53
54
No confidential
function on the
other party
Confidential
function not
accepted
Confidential box
No. NG
55
No interface
function on the
other party
56
Interface not
accepted
57
Interface ID
discrepancy
58
Reception
inhibition number
Communication interruption
content
Communication normal end
The other party has no send
request function when
receiving a send request.
The other party has no data
to send.
DCN is received for DTC
when sending a send
request.
There is no data to send
when sending a send
request.
Discrepancy in the enable
number when sending a
send request.
Discrepancy in the system
number when sending a
send request.
The other party has no
confidential function when
sending a confidential
message. (Including the
other company’s machines)
DCN is received for NSS
when receiving a
confidential message.
A confidential box number
which is not registered is
directed when receiving a
confidential message.
The other party has no
interface function when
sending an interface
command.
DCN is received for NSS
when sending an interface
command.
A receiving station number
which is not registered is
directed when receiving an
interface command.
Discrepancy in the
interface ID when
receiving an interface
command.
Transmission is made from
a reception inhibition
number.
<Communication result codes>
Error
code
0
1
2
3
4
5
6
7
8
9
10
Final reception signal
(Transmitting side)
Abnormal signal
NSF, DIS
CFR
FTT
MCF
PIP, PIN
RTN, RTP
No signal
PPR
Final reception signal
(Receiving side)
Abnormal signal
NSS, DCS
NSC, DTC
EOP
EOM
MPS
PRI-Q
DCN
PPS-EOP
PPS-EOM
PPS-MPS, PPS-NULL
Error
code
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
Final reception signal
(Transmitting side)
RNR
CTR
ERR
Abnormal signal
NSF, DIS
CFR
FTT
MCF
PIP, PIN
RTN, RTP
No signal
PPR
RNR
CTR
ERR
V.8 Phase-1
V.8 Phase-2
V.8 Phase-3
Final reception signal
(Receiving side)
RR
CTC
EOR-Q
PPS-PRI-Q
Abnormal signal
NSS, DCS
NSC, DTC
PPS-EOP
PPS-EOM
PPS-MPS, PPS-NULL
PRI-Q
DCN
RR
CTC
EOR-Q
PPS-PRI-Q
V.8 Phase-1
V.8 Phase-2
V.8 Phase-3
(Note) For error codes 16 – 31, V.34 mode communication.
<Error codes 1>
Error codes 1 are fixed to “00”.
<Error codes 2>
Error
codes 2
01
02
03
04
Content of communication interruption
Transmission length over
EOL time over
Carrier detection time up
Polarity reversion detection (in phase C)
05
06
07
08
8 min over (in phase C)
Memory image decoding error
Memory image decoding error
Time up between frames in phase C
10
11
12
13
14
15
Communication request NG
Polarity reversion detection
Invalid command reception
Time over (1min timer/6sec timer)
PUT error
Time out occurrence during shift from
Primary to Control in V.34 mode
Polarity reversion detection
Invalid command reception
Fall back retry number over
Resend over of retry number
Time over (T5 timer)
Time over (T5 timer) in V.34 mode
Time out occurrence during shift from
Primary to Control in V.34 mode
Communication error due to
communication abnormality between
FAX_SUB and FAX_MAIN
20
21
22
23
24
25
26
30
FO-DC550 TEST COMMAND, FAX SOFT SWITCH, TROUBLE CODES 10 - 71
Transmission/
Reception
Transmission
Reception
Reception
Transmission/
Reception
Transmission
Reception
Transmission
Transmission/
Reception
Reception
Reception
Reception
Reception
Reception
Reception
Transmission
Transmission
Transmission
Transmission
Transmission
Transmission
Transmission
Transmission/
Reception
[11] MAINTENANCE
1. Maintenance table
: Check (Clean, adjust, or replace when required.)
Section
Developing
Process peripheral
Parts
25K
50K
75K
: Clean
: Replace
100K
125K
: Adjust
✩: Lubricate
Remark
Developer
DV blade
DV side seal (F/R)
Drum
2. Maintenance display system
Toner
Life
Remaining quantity
Developer
LED
Machine
Life
LED
Machine
8K
EMPTY
NEAR EMPTY
About 10%
ON
Operation allowed
Flash
Stop
25K
ON at 25K of the developer count.
Selection is available between Not Stop and Stop by Service Simulation (SIM 26-37) Setup.
(If Stop is selected, the LED will flash and stop at 25K.)
∗ Default: Not Stop
∗ Clear: SIM 24-06
Maintenance
LED
Selection is available among 25K, 13K, 9K, 6K, 3K, and free (no lighting) with SIM 21-1.
∗ Default: 25K
∗ Clear: SIM 20-1
Machine
Not stop.
3. Remaining toner indication
TONER FULL
Display for users
Remaining toner indication
100%
75%
Lo
50%
LOW LEVEL
25%
100-90%
89-75%
74-50%
49-25%
24-10%
10%
10 sheets
TONER CARTRIDGE
IS NEAR EMPTY
REPLACE THE
TONER CARTRIDGE
Displayed on the LCD.
Displayed on the LCD.
• The remaining toner indication is based on the number of revolutions of the toner motor.
• The toner END indication appears when the END is detected by the toner sensor.
FO-DC550 MAINTENANCE 11 - 1
[12] USER PROGRAM
The user settings consist of the following items.
1. User programs
A. Copy mode
Program
number
Program name
Setting codes
(factory default setting
appears in bold)
1: 10 SEC.
2: 30 SEC.
3: 60 SEC.
4: 90 SEC.
5: 120 SEC.
6: OFF
1: 30 SEC.
2: 1 MIN.
3: 5 MIN.
4: 30 MIN.
5: 60 MIN.
6: 120 MIN.
7: 240 MIN.
1: ON
2: OFF
1: 5 MIN.
2: 30 MIN.
3: 60 MIN.
4: 120 MIN.
5: 240 MIN.
1
AUTO CLEAR
2
PREHEAT MODE
3
AUTO SHUT-OFF
4
AUTO SHUT-OFF
TIME
5
STREAM FEEDING
1: ON
2: OFF
6
LAYOUT IN 2IN1
7
OFFSET
FUNCTION
ROTATE ORIG.
IMAGE
1: PATTERN 1
2: PATTERN 2
1: ON
2: OFF
1: ON
2: OFF
9
AE/TEXT
RESOLUTION
1: 300dpi
2: 600dpi
10
2-SIDED COPY
MODE
1: HI-SPEED
2: NORMAL
11
MARGIN WIDTH
12
MEM. FOR
PRINTER
13
AUTO KEY REPEAT
1: 1/4"
2: 1/2"
3: 3/4"
4: 1"
1: 30%
2: 40%
3: 50%
4: 60%
5: 70%
1: ON
2: OFF
14
KEY PRESS TIME
8
1: NORMAL
2: 0.5 SEC.
3: 1.0 SEC.
4: 1.5 SEC.
5: 2.0 SEC.
Explanation
• Auto clear time automatically returns the copy settings to the initial settings if no
keys are pressed for a preset period of time following the end of a copy job.
• This program is used to select the period of time. Auto clear time can also be
disabled.
• This function automatically switches the machine to a low power consumption
state if the set duration of time elapses without the machine being used when the
power is on. The power save indicator lights up, however, the keys on the
operation panel can be used. Normal operation automatically resumes when a key
on the operation panel is pressed, an original is placed, a print/fax job is received.
• Use this setting to enable or disable auto power shut-off mode.
• This function automatically switches the machine to a state that consumes even
less power than preheat mode if the set duration of time elapses without the
machine being used when the power is on. All lights except the power save
indicator go off. To resume normal operation, press the [START] key. Normal
operation also resumes automatically when a print/fax job is received or scanning
is begun from a computer. While in auto power shut-off mode, no keys (except the
[START] key) can be used.
• When copying using the RSPF, while "SET ORIGINALS FOR STREAM
FEEDING." appears in the display after an original has been scanned (about 5
seconds), a subsequent original can be placed and automatically fed into the
machine.
• Use this setting to select the layout pattern when two original pages are copied
onto a single sheet of paper.
• When enabled, this function offsets the position of each set of copies in the output
tray in copy mode, and each print job in printer mode.
• When two-sided copying is performed, this function rotates the image on the back
of the original. This is convenient when binding the copies at the top (tablet
binding).
• This setting is used to change the copy resolution in AUTO and TEXT mode from
600 x 300 dpi to 600 x 600 dpi (high-quality mode). Scanning is slower when highquality mode is used.
• If the memory fills up when two-sided copying is performed, "NORMAL" can be
selected to make copying possible. However, "NORMAL" results in a slower
copying speed. Normally "HI-SPEED" is selected to enable fast two-sided
copying.
• Use this setting to set the margin width.
• Use this to change the proportion of machine memory used for printer mode.
• Use this setting to select whether or not holding down a key causes repeated input
of the key. For keys that normally cause a set value to decrease or increase when
held down (for example, the [<] key [v] or [>] key [^]), this program can be used to
have the set value not change when the key is held down.
• Use this setting to select how long a key must be pressed for the input to be
accepted. By selecting a longer time, you can prevent settings from being
changed by the accidental pressing of a key.
FO-DC550 USER PROGRAM 12 - 1
Program
number
Program name
15
KEY TOUCH
SOUND
16
18
SOUND AT
DEFAULT
TONER SAVE
MODE
AE LEVEL ADJUST
19
LANGUAGE
20
RESET FACTORY
21
SORT AUTO
SELECT
17
Setting codes
(factory default setting
appears in bold)
1: LOW
2: HIGH
3: OFF
1: ON
2: OFF
1: ON
2: OFF
1: SPF/RSPF
2: DOCUMENT GLASS
1: AMERICAN ENGLISH
2: FRENCH
3: SPANISH
1: YES
2: NO
1: ON
2: OFF
Explanation
• This sets the volume of beep signals.
• Use this to sound a beep when a base setting is selected.
• This mode reduces toner usage by about 10% when copying. Toner save mode is
effective when the exposure mode is AUTO or TEXT.
• This is used to adjust the exposure level.
• The automatic exposure level can be adjusted separately for the document glass
and the RSPF.
• The factory default setting for the exposure level is center.
• This is used to set the language used in the display.
• This is used to return all settings to the factory default settings.
• Use this setting to enable or disable sort auto select mode.
B. Print mode
Program
number
Program name
Setting codes
(factory default setting
appears in bold)
Explanation
1
FORCED OUTPUT
1: ON
2: OFF
When this function is enabled, printing in printer mode will automatically continue
using a different size of paper if the specified size of paper runs out in all trays. This
feature does not function in copy mode.
2
USB 2.0 MODE
SWITCH *1
1: FULL-SPEED
2: HI-SPEED
This sets the USB 2.0 data transfer speed. To obtain the fastest speed when using
the USB 2.0 connector, first verify that your computer meets the system
requirements (operating system and driver), and then use this program to change
the USB 2.0 mode to "Hi-Speed". Note that the setting should not be changed while
running a TWAIN driver. (For the system requirements.)
3
AUTO TRAY
SWITCH *2
1: ON
2: OFF
If the paper runs out during printing and there is paper of the same size in another
tray, this function automatically switches to that tray (excluding the bypass tray).
The function can be disabled.
*1: The scanning speed increases when the USB 2.0 mode is set to "HI-SPEED", however, the printing speed does not increase considerably.
*2: When the 250-sheet paper feed unit is installed.
C. FAX mode
Program
number
Program name
1
DOC. GLASS SIZE
2
FIXED DOC. SIZE
3
RESO. PRIORITY
4
# OF RINGS (AUTO)
5
6
# OF RINGS
(MANUAL)
AUTO LISTING
7
PRINT SELECTION
Setting codes
(factory default setting
appears in bold)
1: 8.5x11
2: 8.5x14
3: A4
1: 8.5x11
2: 8.5x14
3: A4
1: STANDARD
2: FINE
3: SUPER FINE
0 – 9 (2)
0 – 9 (0)
1: ON
2: OFF
1: ALWAYS PRINTS
2: ERROR ONLY
3: NEVER PRINTS
1: ALWAYS PRINTS
2: ERROR ONLY
3: NEVER PRINTS
Explanation
Set the size of an original faxed from the document glass.
Set the default size of originals faxed from the document glass.
Set the default resolution for fax transmission.
Set the number of rings on which the machine answers calls in automatic reception
mode.
Set the number of rings on which the machine answers calls in manual reception
mode.
Enable automatic printing of the Activity Report when information on a total of 50 fax
transmissions/receptions accumulates.
1: TRANSMISSION
Select the condition for printing reports on fax transmissions.
2: BROADCAST
Select the condition for printing reports on broadcast transmissions.
FO-DC550 USER PROGRAM 12 - 2
Program
number
Program name
7
PRINT SELECTION
8
Setting codes
(factory default setting
appears in bold)
1: ALWAYS PRINTS
2: ERROR ONLY
3: NEVER PRINTS
1: ALWAYS PRINTS
2: ERROR ONLY
3: NEVER PRINTS
00 – 14 (02)
10
RECALL TIMES
BUSY
RECALL TIMES
ERR
RECALL INT. BUSY
11
RECALL INT. ERR
00 – 15 min. (01 min.)
12
SECURITY SELECT
13
15
FAX REMOTE
NUMBER
REMOTE
RECEPTION
FAX SIGNAL RCV
1: ON
2: OFF
0 – 9 (5)
16
RCV REDUCE
17
BEEP LENGTH
18
RINGER VOLUME
19
BEEPER VOLUME
20
DIAL MODE
21
DISTINCTIVE RING
22
INDEX PRINT
23
DATE&TIME
FORMAT
24
PRINT HOLD MODE
25
PRINT PASSCODE
26
2-SIDED RX
27
TRAY SELECTION
(When the 250-sheet
paper feed unit is
installed.)
9
14
Explanation
3: RECEPTION
Select the condition for printing reports on received faxes.
4: IMAGE MEM. PRINT
Enable printing of the original image on transaction reports.
Set the number of recall attempts that are made when the line is busy.
0 – 1 (1)
Set the number of recall attempts that are made when a communication error occurs.
01 – 15 min. (03 min.)
Set the interval between recall attempts when the line is busy. 1 to 15 minutes can
be selected.
Set the interval between recall attempts when a communication error occurs. 0 to 15
minutes can be selected.
Enable the polling security function.
1: ON
2: OFF
1: ON
2: OFF
1: ON
2: OFF
1: 3 SEC
2: 1 SEC
3: NO BEEP
1: OFF
2: LOW
3: MIDDLE
4: HIGH
1: OFF
2: LOW
3: MIDDLE
4: HIGH
1: TONE
2: PULSE
1: OFF
2: STANDARD
3: PATTERN 1
4: PATTERN 2
5: PATTERN 3
6: PATTERN 4
7: PATTERN 5
1: ON
2: OFF
1: 12 HOUR
2: 24 HOUR
1: MMDDYYYY
2: DDMMYYYY
3: YYYYMMDD
1: ON
2: OFF
1: SET
2: CLEAR
1: ON
2: OFF
1: AUTO
2: TRAY 1
3: TRAY 2
Set the 1-digit number used to activate remote fax reception.
Enable the remote reception function.
Enable automatic fax reception when a fax tone is heard after answering a call on an
extension phone.
When a fax is received that is larger that the printing paper, enable reduction of the
fax to the size of the paper to avoid the fax being cut off.
Set the length of the beep that sounds when fax transmission or reception ends.
Set the volume of the ringer.
Set the volume of the beep that sounds when a key is pressed.
Set the dial mode for the type of line you are on.
Set the ring pattern for distinctive ring.
Enable printing of a black mark (index) at the top of each received fax page.
1: TIME FORMAT
Select 12-hour or 24-hour format for the time set in the machine.
2: DATE FORMAT
Set the format of the date in the display and in printouts.
When this mode is enabled, received faxes are held in the memory of the machine
instead of being printed out. To print received faxes, the passcode that was
programmed using "25: PRINT PASSCODE" must be entered. This mode is used to
ensure that received faxes are not misplaced or taken from the paper output tray by
another person.
This setting is used to program the passcode that is required when "24: PRINT
HOLD MODE" is enabled.
Print on both sides of the paper when a multi-page fax is received.
Set the tray for printing received faxes.
FO-DC550 USER PROGRAM 12 - 3
2. Selecting a setting for a user program
Audible signals (key entry beep, invalid key beep, base setting
beep)
1) Press the [MENU] key and then press the [ENTER] key.
The machine sounds three different types of beep signals: a key
entry beep that sounds when a valid key is pressed, an invalid key
beep that sounds when an invalid key is pressed, and a base setting
beep that sounds when a setting is the same as the base setting
(base settings are explained below). The base setting beep is initially
disabled. If you wish to enable the base setting beep, see "SOUND
AT DEFAULT". If you wish to change the volume of the beep signals
or disable them, see "KEY TOUCH SOUND".
In printer mode, the user programs are accessed by simply pressing the [MENU] key.
MAIN MENU
1:USER PROGRAM
2) Press the [<] key [v] or [>] key [^] to select the item that you wish to
configure in the USER PROGRAM items, and then press the
[ENTER] key.
• You can also select a program by directly entering the program
number with the numeric keys.
The beep patterns of each type of beep signal are as follows:
Key entry beep: One beep
Base setting beep: Three beeps
Invalid key beep: Two beeps
Base settings
The base settings are preset standard selections for each copy setting. The base settings are as follows:
Copy ratio: 100%
Paper feed location:
Light and Dark level: Center
Tray 1 (Upper paper tray)
AUTO/TEXT/PHOTO: AUTO
USER PROGRAM
2:PREHEAT MODE
3) Press the [<] key [v] or [>] key [^] to change the setting of the
selected item.
PREHEAT MODE
1:1 MIN
NOTE:
• If you mistakenly select the wrong item, press the [CLEAR] key [C]
and repeat the procedure from step 2.
• To cancel a setting for a user program, press the [MENU] key.
4) Press the [ENTER] key.
Your selection appears briefly and then the previous screen
appears.
NOTE:
When "AE LEVEL ADJUST" is selected in the user programs and the
[ENTER] key is pressed, the automatic exposure adjustment screen
appears. Adjust the exposure and press the [ENTER] key.
FO-DC550 USER PROGRAM 12 - 4
FO-DC550 ELECTRICAL SECTION 13 - 1
Fan Motor (1speed)
Shifter Motor
Duplex Motor
MCU-PWB
SDRAM
Driver
Driver
Sensor/SW
PAPD,PPD3,
PD2,CED2
Mechanical load
CPFS2
3.3V
Toner Motor
Driver
Mirror Motor
Driver
(296pin)
CCFL x 2
LSU
LASER
D[15…0]
A[19…1]
Polygon
Motor
LCX574
I2C Bus
2Kbyte
EEPROM
EEPROM
(CRUM)
OP-CLK
OP-LATCH
OP-DATA
POWER SUPPLY
AC Code
D[7..0]
RD
CS
INT
PSW
4Mb
or 8Mb
or 16Mb
8bit
LCD
(2 x 20)
START KEY
HC238
(3 to 8 decode) 8bit
HC151
PSL LED
OA982
Flash ROM
OPE PWB
SDRAM
256Mbx1
Optional
32.3022MHz
Buzzer
KEY Matrix
Copier 24pcs
12MHz
ISP1581
LED
Copier 11pcs
FAX I/F
FAX only
FAX
Modem / LIU PCBA
LED Driver
P-Bus
USB
RJ45
(N/W
connector)
(Power Supply unit)
DC Adapter
Network BOX
Optional
LCD E
LCD RS
LCD R/W(TBD)
LCD DB7-4
KEYSCAN1-3
SELIN1,2,3
KEYIN
PSL
TC, GRID, MC, BIAS
HVU
CPU CLK(19.6608MHz)
SSCG
/POFF,HL,PR
FW
3.3V,5VEN,5V,24V
PMCLK
8Mbit
CPU
H8S/2321
(19.6608MHz)
System Reset
8
8
UART
SPF Motor
Driver
Image BUS(PI-Bus)
Image BUS(PO-Bus)
Reset IC
3.3V
HOME
POSITION
SENSOR
1Mbit
SRAM
Flash ROM
MHPS
DC-DC
0 - 24V
Lamp
Inverter
PWM
8bits (MSB/LSB)
KRONOS ASIC
16bits
AD
3.3V
HC151
M
P
X
Main Motor
Scanner CLK(48MHz)
16Mbyte
A5V
IEEE 1284 I/F
Printer CLK(16.1511MHz)
LVC1284
2nd Cassette
(Optional)
I
E
E
E
1
2
8
4
CCD Driver
R
G
B
/MMD
5V
CCD
(uPD8861)
Reg
AFE(AD9826)
A
C
G
D
C
S
12V
/MMRDY
12V
PMD
CCD PWB
Speaker
USB2.0
High-speed
Carriage Unit
SDOD
SPOD
Interlock SW
Cassette detector X 2
Drum Initial detector
PPD1
POD
MFD
PPD2
LED
3 pcs
KEY Matrix
21 pcs
FAX OPE PWB
Note: Energy-saving 1W correspondence
CPU I/O
CPU INTERRUPT
SPPD
Sensor/SW
(Electorical detector/SW/Sensor)
(Counter) MCNT
(SPF UNIT SGS, SRRC, SPUS, SPPS,
MPFS,RRS,CPFS1
Mechanical Load
[13] ELECTRICAL SECTION
1. Block diagram
A. Overall block diagram
2. Circuit descriptions
A. Main PWB (MCU)
(1) General
The MCU PWB is composed of:
• CPU peripheral section which performs mechanical sequence
control, U/I, and each function job management.
The CPU connects with the ASIC and memory by use of the system
bus and performs jog management and sequence control of the
whole engine.
• Image process ASIC which performs image process, CCD control,
LSU control, and print control.
• OA982 peripheral section which performs E-Sort and FAX control.
The OA982 performs image data input/output with the ASIC,
SDRAM memory management, and communication with USB2.0
devices.
• I/F section for USB2.0 and IEEE1284 control. (For the AL series,
IEEE1284 is not available.)
• Motor control circuit
• Mechanical load, sensor I/O circuit
It performs control and management of the process, the transport
loads, the fusing, the optical, and the operation panel sections for executing a series of copy/print/scan operations.
(2) CPU signal table (H8S/2321)
PIN
No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
/CS1
/CS0
GND
GND
Vcc
A0
A1
A2
A3
GND
A4
A5
A6
A7
A8
A9
A10
A11
GND
A12
A13
A14
A15
A16
A17
A18
A19
GND
A20
PSW
31
SPPD
32
CCD_TG
33
MHPS
34
/CPUSYNC
35
36
37
GND
GND
FW
Signal code
Input/
Output
Output
Output
Output
Output
Output
Output
Output
Output
Output
Output
Output
Output
Output
Output
Output
Output
Output
Output
Output
Output
Output
Output
Interruption
level input
Interruption
level input
Interruption
level input
Interruption
level input
Interruption
level input
Interruption
level input
Operating
SRAM chip select
Flash ROM chip select
DGND
DGND
CPU3.3V
Address bus
Address bus
Address bus
Address bus
DGND
Address bus
Address bus
Address bus
Address bus
Address bus
Address bus
Address bus
Address bus
DGND
Address bus
Address bus
Address bus
Address bus
Address bus
Address bus
Address bus
Address bus
DGND
Pull-Up
Print SW
SPF paper sensor
CCD horizontal sync signal
Mirror Home Position
Horizontal sync (ASIC)
DGND
DGND
Zero cross signal
PIN
No.
38
ARB_INT
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
Vcc
D0
D1
D2
D3
GND
D4
D5
D6
D7
D8
D9
D10
D11
GND
D12
D13
D14
D15
Vcc
POFF
TxD1
SDA
SCL
LCDRS
LCDE
GND
CS4 (FAX)
GND
GND
RY/BY
LCDDB4
LCDDB5
BZR
LCDDB7
LCDDB6
Reset OUT1
DMT0
DMT1
DMT2
DMT3
WDTOVF
/RES
NMI
STBY
Vcc
XTAL
EXTAL
GND
CPUCLK
Vcc
PRINTST
/RD
/HWR
/LWR
SELIN3
SELIN2
SELIN1
ESSTS
ESCMD
GND
GND
ESSRDY
ESCRDY
AVcc
Vref
RTH
Signal code
FO-DC550 ELECTRICAL SECTION 13 - 2
Input/
Output
Interruption
level input
Data I/O
Data I/O
Data I/O
Data I/O
Data I/O
Data I/O
Data I/O
Data I/O
Data I/O
Data I/O
Data I/O
Data I/O
Data I/O
Data I/O
Data I/O
Data I/O
Output
Output
Output
Output
Output
Output
Input
Output
Output
Output
Output
Output
Output
Output
Output
Output
Output
Output
Input
Output
Output
Input
Output
Output
Output
Output
Output
Output
Output
Output
Output
Output
Input
Input
Output
Analog
input
Operating
ASIC interruption
CPU3.3V
Data bus
Data bus
Data bus
Data bus
DGND
Data bus
Data bus
Data bus
Data bus
Data bus
Data bus
Data bus
Data bus
DGND
Data bus
Data bus
Data bus
Data bus
CPU3.3V
Shut off control
For debug
EEPROM Data bus
EEPROM clock
LCD control
LCD control
DGND
Chip select (FAX)
DGND
DGND
Flash Busy signal
LCD control
LCD control
Buzzer signal
LCD control
LCD control
Reset signal
Duplex Motor signal
Duplex Motor signal
Duplex Motor signal
Duplex Motor signal
NC Pull-Up
Reset
NC Pull-Up
NC Pull-Up
CPU3.3V
Clock
Clock
DGND
NC
CPU3.3V
Print start signal
Read signal
Write signal (High address)
Write signal (Low address)
HC151 select signal
HC151 select signal
HC151 select signal
E-sort control
E-sort control
DGND
DGND
E-sort control
E-sort control
CPU3.3V
CPU3.3V
Fusing thermistor
PIN
No.
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
Signal code
ESPAGE
SIN1
SIN2
SIN3
KEY IN
MSUST1
Avss
GND
/SCANSP
/SCANST
/TRANSST
PMCLK
SPMT3
SPMT2
SPMT1
SPMT0
GND
GND
Vcc
PSL
/CS3
/CS2
Input/
Output
Input
Input
Input
Input
Input
Input
Output
Output
Output
Output
Output
Output
Output
Output
Output
Output
Output
Operating
E-sort control
HC151 select detection
HC151 select detection
HC151 select detection
Pull up
NC
NC
DGND
DGND
Scan STOP signal
Scan START signal
ASIC transfer signal
Polygon clock
SPF motor signal
SPF motor signal
SPF motor signal
SPF motor signal
DGND
DGND
CPU3.3V
Power save LED control
Chip select signal
ASIC chip select
(3) Image process ASIC (HG73C114HF)
a. General
The ASIC is composed of the three blocks: the image process block,
the print control block, and the I/F block.
Image process section
According to the operation mode set by the register set value, the
image data from the CCD PWB are placed under shading, AE process, input gamma process, area separation, filter process, resolution conversion, zoom process, output gamma process, and binary
coding.
Print control section
During copying, image-processed data are outputted to the LSU at
the timing of LSU writing.
I/F section
This section performs DRUM control as image data buffer, image
data send/receive with the OA982, and data send/receive with the
IEEE1284 I/F.
nCS2
PORT1OUT[15..0]
nRD
I/O PORT
nLWR
A[9..1]
CPU BUS
I/F
OPE-LATCH
D[15..0]
LED Driver
Control
nRESET
JTAG
PORT2OUT[10..0]
TONER MOTOR
Control
to SDRAM
64Mb or 128Mb
(Op.400MByte)
OPE-DATA
OPE-CLK
TMCLK,TMEN
TM,TM-
to OPU-PWB
to TONER MOTOR DRIVER
CCD-RS,CCD-CK1,CCD-CK2
to CCD(SCAN UNIT)
CCD-CP,CCD-SHR
bsmp,vsmp,mclk,OEB
afesen,afesck,afesdi
to AFE(SCAN UNIT)
AFE-DB[7..0]
to USB I/F
to IEEE1284 I/F
MIRCNT,MTR-Y1,MTR-PH-1,MTR-I01,MTR-I11,MTR-I21
MTR-Y2,MTR-PH-2,MTR-I02,MTR-I12,MTR-I22
to MIRROR MOTOR DRIVER
SYNC
to LSU-PWB
LD
to CCFL(Scan UNIT)
LEND
CL
CPUSYNC
FO-DC550 ELECTRICAL SECTION 13 - 3
b. ASIC (Signal table)
PIN
No.
1
2
3
4
5
6
7
8
9
10
11
cpudata7
cpudata6
cpudata5
cpudata4
VCC_AC
cpudata3
cpudata2
cpudata1
cpudata0
GND_AC
mircnt
IN/OUT
IN/OUT
IN/OUT
IN/OUT
Power
IN/OUT
IN/OUT
IN/OUT
IN/OUT
Power
OUT
CPU
CPU
CPU
CPU
CPU data bus
CPU data bus
CPU data bus
CPU data bus
CPU
CPU
CPU
CPU
CPU data bus
CPU data bus
CPU data bus
CPU data bus
Buffer IC
12
13
14
15
16
17
18
19
20
21
cpusync
mem_intr
arb_intr
VCC_core
cpu_ad8
cpu_ad7
cpu_ad6
cpu_ad5
GND_core
ram_clk_in
OUT
CPU
OUT
Power
IN
IN
IN
IN
Power
IN
CPU
SPF scanner select
signal
CPU SYNC signal
Not used
INTR signal
CPU
CPU
CPU
CPU
CPU address bus
CPU address bus
CPU address bus
CPU address bus
ASIC
22
23
24
25
26
27
28
29
30
31
32
cpu_ad4
cpu_ad3
cpu_ad2
cpu_ad1
cpu_ad0
xcpucs
sfclk
GND_core
xcpuwr
xcpurd
nrst
IN
IN
IN
IN
IN
IN
IN
Power
IN
IN
IN
SDRAM clock on the
board
CPU address bus
CPU address bus
CPU address bus
CPU address bus
CPU address bus
CS signal
Clock
33
34
35
36
37
38
39
40
41
42
43
44
VCC_core
pfclk2
clock_sw
GND_core
pfclk1_xout
pfclk1
VSSPLL2
VDDPLL2
VSS2
VDDI2
tm2_15m
xsync
Power
IN
IN
Power
OUT
IN
45
46
47
48
49
GND_AC
xld
xlend
VCC_AC
mmd
Power
OUT
OUT
Power
OUT
50
51
pmd
tc
OUT
OUT
I/O
Tr array IC
52
gridl
OUT
Tr array IC
Signal Name
IN/OUT Connected to
IN
CPU
CPU
CPU
CPU
CPU
CPU
Oscillator
CPU
CPU
SYSTEM
RESET
Description
CPU write signal
CPU read signal
SYSTEM RESET
Not used
Pull up
X-tal units
X-tal units
LSU
VIDEO clock
VIDEO clock
Pull up
Pull up
Pull up
Pull up
Pull up
Horizontal sync
signal from LSU
(/SYNC)
LSU
LSU
Laser drive signal
Laser APC signal
Tr array IC
Main motor control
signal. "H": Main
motor ON
Polygon motor drive
Transfer charger
control signal. "H":ON
Main charger grid
control signal. "H": L
output
PIN
Signal Name
No.
53 mc
OUT
Tr array IC
54
55
56
bias
NC
vfmcnt
OUT
OUT
OUT
I/O
I/O
Tr array IC
57
58
VCC_core
vfm
Power
OUT
Tr array IC
59
60
61
62
/FPOFF
GND_core
DEV DIR
spfclh
OUT
Power
OUT
OUT
I/O
Tr array IC
63
spfrsol
OUT
Tr array IC
64
spfgsol
OUT
Tr array IC
65
spfpsol
OUT
Tr array IC
66
67
VCC_core
bias
Power
OUT
Tr array IC
68
lden
OUT
Tr array IC
69
70
71
72
73
GND_AC
MRPS1
MRPS2
MRPS3
CPFS1
Power
OUT
OUT
OUT
OUT
I/O
I/O
I/O
I/O
SPF current control
SPF current control
SPF current control
1st cassette pick up
solenoid
74
75
VCC_AC
CPFS2
Power
OUT
I/O
76
77
pr
hl
OUT
OUT
I/O
Tr array IC
2nd cassette pick up
solenoid
Power relay control
Heater lamp control
signal. "H":ON
78
79
80
GND_core
MPFS
miron
Power
OUT
OUT
I/O
Buffer IC
81
82
83
84
85
86
87
spfon
KEYSC1
KEYSC2
KEYSC3
IMC ready
VCC_core
tmx
OUT
OUT
OUT
OUT
OUT
Power
OUT
Buffer IC
88
tm
OUT
Buffer IC
89
op_data
OUT
Tr array IC
90
ope_latch
OUT
Tr array IC
91
GND_AC
Power
FO-DC550 ELECTRICAL SECTION 13 - 4
IN/OUT Connected to
I/O
Buffer IC
I/O
I/O
I/O
I/O
Description
Main charger control
signal. "H": ON
HV bias drive
Not used
Ventilation fan
rotation speed control
signal. "H": High
speed, "L": Low
speed
Ventilation fan control
signal. "H": Fan ON
FAX poff signal
CRUM bus control
SPF/RSPF resist
roller clutch control
signal "H":ON
SPF/RSPF document
feed solenoid control
signal "H":ON
SPF/RSPF gate
solenoid control
signal "H":ON
SPF/RSPF document
transport solenoid
control signal "H":ON
DV bias control
signal. "H":ON
Laser circuit control
signal. "H": Laser
circuit ON
Multi-bypass solenoid
SPF scanner select
signal
SPF ON signal
Key sense control
Key sense control
Key sense control
IMC control
Toner motor control
signal
Toner motor control
signal
Operation circuit data
signal
Operation circuit latch
signal. Data take-in at
"L"
PIN
Signal Name IN/OUT Connected to
Description
No.
92 op_clk
OUT
Tr array IC
Operation circuit
clock signal
93 VCC_AC
Power
94 scanstop
IN
CPU
Scan stop signal
95 testpin0
IN
TEST
TEST
96 testmode_on IN
TEST
TEST
97 ie1284_stb
IN
I/F board
/STB signal
connector
(IEEE1284
communication port)
98 ie1284_autofd IN
I/F board
/AUTOFD signal
connector
(IEEE1284
communication port)
99 VCC_core
Power
100 ie1284_slctin IN
I/F board
/SLCTIN signal
connector
(IEEE1284
communication port)
101 ie1284_init
IN
I/F board
/INIT signal
connector
(IEEE1284
communication port)
102 ie1284_slct
OUT
I/F board
SLCT signal
connector
(IEEE1284
communication port)
103 GND_core
Power
104 ie1284_pe
OUT
I/F board
PE signal (IEEE1284
connector
communication port)
105 ie1284_busy
OUT
I/F board
BUSY signal
connector
(IEEE1284
communication port)
106 ie1284_ack
OUT
I/F board
/ACK signal
connector
(IEEE1284
communication port)
107 ie1284_fault
OUT
I/F board
/FAULT signal
connector
(IEEE1284
communication port)
108 VCC_core
Power
109 ie1284_rev
OUT
I/F board
/REV signal
connector
(IEEE1284
communication port)
110 ie1284_parad7 IN/OUT I/F board
DATA bus (IEEE1284
connector
communication port)
111 ie1284_parad6 IN/OUT I/F board
DATA bus (IEEE1284
connector
communication port)
112 ie1284_parad5 IN/OUT I/F board
DATA bus (IEEE1284
connector
communication port)
113 ie1284_parad4 IN/OUT I/F board
DATA bus (IEEE1284
connector
communication port)
114 ie1284_parad3 IN/OUT I/F board
DATA bus (IEEE1284
connector
communication port)
115 ie1284_parad2 IN/OUT I/F board
DATA bus (IEEE1284
connector
communication port)
116 VCC_AC
Power
117 ie1284_parad1 IN/OUT I/F board
DATA bus (IEEE1284
connector
communication port)
118 ie1284_parad0 IN/OUT I/F board
DATA bus (IEEE1284
connector
communication port)
119 suspend
OUT
I/F board
SUSPEND signal
connector
(USB communication
port)
120 GND_AC
Power
121 oen
OUT
I/F board
OEN signal (USB
connector
communication port)
122 vmout
OUT
I/F board
VMOUT signal (USB
connector
communication port)
123 vpout
OUT
I/F board
VPOUT signal (USB
connector
communication port)
124 GND_core
Power
PIN
Signal Name
No.
125 vmin
IN
126 vpin
IN
127 rcv
IN
128
129
130
131
IN
IN
IN
IN
scanst
printst
receptst
transst
IN/OUT Connected to
132 VCC_core
133 dci_dat7
Power
IN
134 dci_dat6
IN
135 dci_dat5
IN
136 dci_dat4
IN
137 dci_dat3
IN
138 dci_dat2
IN
139 dci_dat1
IN
140 dci_dat0
IN
141 GND_core
142 out_dc_req
Power
IN
143 in_dc_req
IN
144 GND_AC
145 out_dc_ack
Power
OUT
146 out_dc_wt
OUT
147 VCC_AC
148 in_dc_ack
Power
OUT
149 in_dc_cs
OUT
150 dco_dat7
OUT
151 dco_dat6
OUT
152 dco_dat5
OUT
153 dco_dat4
OUT
154 dco_dat3
OUT
155 VCC_AC
156 dco_dat2
Power
OUT
157 dco_dat1
OUT
158 dco_dat0
OUT
159
160
161
162
163
164
hsync
GND_core
out_req
in_ack
in_cs
GND_AC
FO-DC550 ELECTRICAL SECTION 13 - 5
Description
I/F board
connector
I/F board
connector
I/F board
connector
CPU
Start signal
Start signal
CPU
VMIN signal (USB
communication port)
VPIN signal (USB
communication port)
RCV signal (USB
communication port)
Scan start signal
Start signal
Start signal
Data transfer start
signal
E-SORT
(OA982)
E-SORT
(OA982)
E-SORT
(OA982)
E-SORT
(OA982)
E-SORT
(OA982)
E-SORT
(OA982)
E-SORT
(OA982)
E-SORT
(OA982)
E-SORT data bus
E-SORT
(OA982)
E-SORT
(OA982)
E-SORT control
signal
E-SORTcontrol signal
E-SORT
(OA982)
E-SORT
(OA982)
E-SORT control
signal
E-SORT control
signal
E-SORT
(OA982)
E-SORT
(OA982)
E-SORT
(OA982)
E-SORT
(OA982)
E-SORT
(OA982)
E-SORT
(OA982)
E-SORT
(OA982)
E-SORTcontrol signal
E-SORT
(OA982)
E-SORT
(OA982)
E-SORT
(OA982)
FAX
E-SORT data bus
E-SORT data bus
E-SORT data bus
E-SORT data bus
E-SORT data bus
E-SORT data bus
E-SORT data bus
E-SORT data bus
E-SORTcontrol signal
E-SORT data bus
E-SORT data bus
E-SORT data bus
E-SORT data bus
E-SORT data bus
E-SORT data bus
E-SORT data bus
FAX
Power
Not used
Not used
Not used
Power
PIN
No.
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
Signal Name
IN/OUT Connected to
mdat00
mdat01
mdat02
mdat03
VCC_core
mdat04
mdat05
mdat06
GND_core
mdat07
mdat08
mdat09
VCC_AC
mdat10
mdat11
mdat12
VCC_core
mdat13
mdat14
mdat15
GND_AC
pcl_s_print
fax_s_print
es_s_print
out_ack
out_cs
in_req
VCC_core
TCK
TMS
TRSTA
TDI
TDO
GND_core
afp_vsmp
ccd_tg
ccdrs
afp_bsmp
ccdcp
afe_sdata
ccd_ph2
ccd_ph1
afp_afesen
GND_core
afp_adcclk
VCC_core
afp_afesck
GND_AC
afp_data7
afp_data6
afp_data5
afp_data4
afp_data3
afp_data2
afp_data1
afp_data0
VCC_AC
cl
Power
OUT
OUT
OUT
OUT
OUT
IN
OUT
OUT
OUT
Power
OUT
Power
OUT
Power
IN
IN
IN
IN
IN
IN
IN
IN
Power
OUT
223 GND_core
224 mtr_y3
Power
OUT
I/O
225 mtr_y2
OUT
Tr array IC
Description
Not used
Not used
Not used
Not used
PIN
Signal Name
No.
226 mtr_y1
OUT
Tr array IC
Carriage motor
current control signal
227 VCC_core
228 mtr_phase2
Power
OUT
Motor driver
229 mtr_i02
OUT
Motor driver
230 mtr_i12
OUT
Motor driver
231 mtr_i22
OUT
Motor driver
232 mtr_phase1
OUT
Motor driver
233 mtr_i01
OUT
Motor driver
234 mtr_i11
OUT
Motor driver
235 mtr_i21
OUT
Motor driver
Carriage motor
control signal
Carriage motor
control signal
Carriage motor
control signal
Carriage motor
control signal
Carriage motor
control signal
Carriage motor
control signal
Carriage motor
control signal
Carriage motor
control signal
236 GND_AC
237 ram_mad3
Power
OUT
SDRAM
238 ram_mad2
OUT
SDRAM
239 GND_core
240 ram_mad1
Power
OUT
SDRAM
241 ram_mad0
OUT
SDRAM
242 ram_mad10
OUT
SDRAM
243 VCC_core
244 ram_banks1
Power
OUT
SDRAM
245 ram_banks0
OUT
SDRAM
246 xram_cs
OUT
247 xram_ras
OUT
SDRAM
248 xram_cas
OUT
SDRAM
249 VCC_AC
250 xram_wde
Power
OUT
SDRAM
251 ram_dqm0
OUT
SDRAM
252 GND_AC
253 ram_data7
Power
IN/OUT SDRAM
IN/OUT Connected to
Power
Not used
Not used
Not used
Power
Not used
Not used
Not used
Power
Not used
Not used
Not used
Power
Not used
Not used
Not used
Power
Not used
Not used
Not used
Not used
Not used
Not used
Power
JTAG
JTAG
JTAG
JTAG
JTAG
Not used
Not used
Not used
Not used
Not used
CCD PWB
CCD PWB
CCD PWB
CCD PWB
CCD PWB
CCD PWB
CCD PWB
CCD PWB
CCD PWB
AFE control signal
CCD control signal
CCD control signal
AFE control signal
CCD control signal
AD's serial data
CCD control signal
CCD control signal
AFE control signal
CCD PWB
AFE control signal
CCD PWB
AFE control signal
CCD PWB
CCD PWB
CCD PWB
CCD PWB
CCD PWB
CCD PWB
CCD PWB
CCD PWB
Image scan data
Image scan data
Image scan data
Image scan data
Image scan data
Image scan data
Image scan data
Image scan data
Logic IC
Copy lamp control
signal
Carriage motor
current control signal
Carriage motor
current control signal
FO-DC550 ELECTRICAL SECTION 13 - 6
Description
SDRAM (Image
process page
memory) address bus
SDRAM (Image
process page
memory) address bus
SDRAM (Image
process page
memory) address bus
SDRAM (Image
process page
memory) address bus
SDRAM (Image
process page
memory) address bus
SDRAM (Image
process page
memory) BANK
signal
SDRAM (Image
process page
memory) BANK
signal
SDRAM (Image
process page
memory) CS signal
SDRAM (Image
process page
memory) RAS signal
SDRAM (Image
process page
memory) CAS signal
SDRAM (Image
process page
memory) WDE signal
SDRAM (Image
process page
memory) DQM signal
SDRAM (Image
process page
memory) data bus
IN/OUT SDRAM
262 GND_AC
263 ram_data15
Power
IN/OUT SDRAM
264 ram_data14
IN/OUT SDRAM
265 VCC_AC
266 ram_data13
Power
IN/OUT SDRAM
267 ram_data12
IN/OUT SDRAM
268 ram_data11
IN/OUT SDRAM
269 ram_data10
270 ram_data9
271 ram_data8
IN/OUT SDRAM
IN/OUT SDRAM
IN/OUT SDRAM
Power
OUT
SDRAM
274 ram_cke
OUT
SDRAM
275
276
277
278
Power
GND_AC
ram_clk_out
GND_core
ram_mad12
SDRAM (Image
process page
memory) data bus
SDRAM (Image
process page
memory) data bus
SDRAM (Image
process page
memory) data bus
SDRAM (Image
process page
memory) data bus
SDRAM (Image
process page
memory) data bus
SDRAM (Image
process page
memory) data bus
Power
OUT
SDRAM
286 ram_mad5
OUT
SDRAM
287 ram_mad4
OUT
SDRAM
288
289
290
291
292
293
294
295
296
Power
IN/OUT
IN/OUT
IN/OUT
IN/OUT
IN/OUT
IN/OUT
IN/OUT
IN/OUT
CPU
CPU
CPU
CPU
CPU
CPU
CPU
CPU
GND_AC
cpudata15
cpudata14
cpudata13
cpudata12
cpudata11
cpudata10
cpudata9
cpudata8
SDRAM
SDRAM's clock
SDRAM
279 ram_mad11
OUT
SDRAM
280 ram_mad9
OUT
SDRAM
SDRAM (Image
process page
memory) address bus
SDRAM (Image
process page
memory) address bus
SDRAM (Image
process page
memory) address bus
CPU data bus
CPU data bus
CPU data bus
CPU data bus
CPU data bus
CPU data bus
CPU data bus
CPU data bus
This circuit detects ON/OFF of the power source, and controls start/
stop of each circuit. The voltage of 3.3V in the MCU PWB is detected
by the reset IC to generate the reset signal.
When the power voltage reaches the specified level, each circuit is
operated, but stopped before the power voltage falls below the specified level in order to protect against malfunction of the circuit. The
CPU/Flash ROM is reset by the power reset circuit, and system reset
of ASIC, OA982, FAX, and NIC is generated from the CPU (generalpurpose port output).
Reset IC
VCC3
VCC3
R18
11kF
R20
R19
3.3kJ
IC4
1
NC
2
IN
3
NC
4
GND
NC
VCC
OUT
Cd
10kF
8
7
6
5
/RESET0
C22
0.1u
M51957BFP
SDRAM (Image
process page
memory) DQM signal
SDRAM (Image
process page
memory) CKE signal
Power
OUT
SDRAM (Image
process page
memory) address bus
SDRAM (Image
process page
memory) address bus
SDRAM (Image
process page
memory) address bus
(4) Reset circuit
2
272 VCC_core
273 ram_dqm1
SDRAM (Image
process page
memory) data bus
SDRAM (Image
process page
memory) data bus
284 VCC_AC
285 ram_mad6
SDRAM (Image
process page
memory) address bus
SDRAM (Image
process page
memory) address bus
1
261 ram_data0
SDRAM
Description
2
IN/OUT SDRAM
OUT
FO-DC550 ELECTRICAL SECTION 13 - 7
1
IN/OUT SDRAM
SDRAM (Image
process page
memory) data bus
SDRAM (Image
process page
memory) data bus
SDRAM (Image
process page
memory) data bus
SDRAM (Image
process page
memory) data bus
283 ram_mad7
C23
OPEN
2
260 ram_data1
Power
IN/OUT SDRAM
SDRAM
1
259 ram_data2
IN/OUT SDRAM
Power
OUT
IN/OUT Connected to
2
257 GND_core
258 ram_data3
IN/OUT SDRAM
SDRAM (Image
process page
memory) data bus
SDRAM (Image
process page
memory) data bus
SDRAM (Image
process page
memory) data bus
PIN
Signal Name
No.
281 VCC_core
282 ram_mad8
1
256 ram_data4
IN/OUT SDRAM
Description
2
255 ram_data5
IN/OUT Connected to
1
PIN
Signal Name
No.
254 ram_data6
(2-C4)
(5) Heater lamp control circuit
The CPU converts the inputted analog voltage into a digital value. The
digital conversion value and the set value of the test command are
compared to control ON/OFF of the heater lamp according to the level,
controlling the heat roller surface temperature to be the fixed level.
12V
1
3 +
1
MA700
FTH (5-B2)
12V
C110
0.1u
2
R71
4.3kF
4
1
1
2 -
2
R70
10kF
2
R69
1kJ
IC22A
KIA393F
2
2
2
2
8
R68
7.5kF
D1
1
VCC3
1
R67
1MF
1
R66
1kF
1
VCC3
1
The heater lamp control circuit detects the heat roller surface temperature, and converts the temperature into a voltage. The converted voltage is inputted to the CPU.
2
a. Outline
VCC3
VCC3
D3
D2
1
1
12V
3
3
2
2
8
KDS226
3 +
(11-C1) RTH_IN
KDS226
IC24A
KIA358F
1
1
R81
300J
2
1
R82
100J
RTH (1-A3)
2
12V
4
C111
22000p
1
8
THOPEN (4-A4)
R87
240J
1
R85
10kF
2
1
7
6 -
3
R86
240J
5 +
2
1
1 2
2
4
(11-B2)
(6-A1)
(6-A1)
(6-A1)
(11-B2)
2
PMCLK_A
MRPS_1
MRPS_2
MRPS_3
/LDEN
1
16
15
14
13
12
11
10
9
R84
10kJ
C114
22000p
2
1C
2C
3C
4C
5C
6C
7C
NC
1
1B
2B
3B
4B
5B
6B
7B
G
1
1
2
3
4
5
6
7
8
IC22B
KIA393F
2
1
PMCLK
MRPS1
MRPS2
MRPS3
LDEN
HL
FTH
0.1u
5V
R83
1.2kF
IC26
(1-A2)
(2-C1)
(2-D1)
(2-D1)
(2-C1)
(2-D1)
(5-E3)
12V
C113
2
2
VCC3
1SS355
Q2
KRA119S
C112
0.1u
INT5V
D4
1
1
2 -
2
2
KID65503F
HLOUT (10-B3)
[High temperature protection circuit in case of CPU hung up
(uncontrollable)]
For IC22 3Pin (reference voltage), +3.3V is divided by the resistor. The
thermistor terminal voltage is inputted to IC22 2Pin. When, therefore,
the voltage at 2Pin falls below the voltage at 3Pin, IC22 1Pin becomes
"H" and the HL signal is pulled to the GND level, suppressing generation of the lighting signal of the heater lamp. (IC22 output 1Pin is normally Low.)
[When the heat roller surface temperature is lower than the set
level]
a. When the thermistor terminal voltage is higher than the set level,
the output signal HL from ASIC becomes HIGH level.
b. This HL signal becomes the HLOUT signal through IC26, and is
inputted to the photo triac coupler in the power PWB. When, therefore, the HL signal is HIGH, the internal triac turns on.
[When the thermistor is open]
The voltage at IC22 6Pin becomes higher than the voltage at 5Pin, and
the 7Pin output THOPEN becomes LOW. This is inputted to the CPU
to display the trouble code H2.
(6) Driver circuit (Clutch, solenoid)
Since a load cannot be directly driven by each load signal from the
CPU or the ASIC, each load is driven through the driver IC (transistor
array).
A large drive current (load current) is ordained from a small input current (ASIC output current).
When the driver input voltage (base resistor input) is HIGH, the transistor turns ON to flow a current through the load, operating the load.
+24V
c. When the internal triac turns on, the heater lamp lights up.
[When the heat roller surface temperature is higher than the set
level]
a. When the thermistor terminal voltage falls below the set level, the
output signal HL from ASIC becomes LOW level.
ASIC/CPU
OUT PUT
b. The HL signal becomes LOW, the power PWB photo triac coupler
turns OFF, and the heater lamp turns OFF.
FO-DC550 ELECTRICAL SECTION 13 - 8
LOAD
LOAD
(7) Toner motor control circuit
The IC32 is the motor drive IC, which generates pseudo-AC waveforms by the pulse signal from the ASIC to drive the toner supply
motor.
Tonner Motor Driver
1
+
C129
2
1
24V
0.1u/50V
2
C128
10u/35V
IC32
1
1
2
2
1
2
3
4
7
10
11
12
13
2
R113
47kJ
2
R112
47kJ
19
20
18
21
R106
1kJ
1
1
(4-D3) (TM)
(4-D3) (TM_)
R105
1kJ
PGND
PGND
Vcc
PSAVE
VM
Rin
OUT1
Fin
OUT2
VREF
RNF
GND
NC
FIN
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
17
16
9
5
TMB_O (11-A1)
TMA_O (11-A1)
6
8
FIN
25
24
23
22
15
14
BA6920FP
PGND
(8) Main motor control circuit/ LSU (Polygon motor)
control circuit
through the driver IC27 to the control circuit in the main motor/LSU,
rotating each motor.
The motors are driven by the MMD (main motor) signal and the PMD
(polygon motor) signal from the ASIC.
When the motor RPM reaches the specified level, the MMLD signal
(main) and the PMLD signal (LSU) become LOW. The CPU detects it
to start process control.
The MMD signal and the PMD signal are turned HIGH and sent
5V
1
2
3
4
5
6
7
8
1B
2B
3B
4B
5B
6B
7B
G
1C
2C
3C
4C
5C
6C
7C
NC
16
15
14
13
12
11
10
9
/MMD
MMref0
MMref1
MMref2
/POFF
/PMD
(11-A4)
(6-A3)
(6-A3)
(6-A3)
(10-B4)
(11-B2)
R88
10kJ
Q3
KRC106S
3
2
(2-C1)
MMD
(2-A3) MM_Y1
(2-A3) MM_Y2
(2-C1) MM_Y3
(1-D3) POFF
(2-C1)
PMD
(2-C1) /LEND
1
IC27
SHOLD (11-B2)
2
1
KID65503F
(9) Mirror motor control circuit, SPF motor control circuit,
Duplex motor control circuit, Shifter motor control
circuit.
Stepping motors are employed for the mirror motor, the SPF motor,
and the duplex motor. The driver for IC29 (for the mirror motor) is the
bipolar drive constant current drive IC. The drive for IC31 (for the SPF)
is the uni-polar drive constant current drive IC. The drive for IC28 (for
the duplex) and IC30 (for the shifter) is the constant current drive IC.
Each motor is driven in W1-2 phase excitement, 1-2 phase excitement,
or 2-phase excitement.
The mirror motor/SPF motor related to image scan are driven by a constant current, and each motor current is switched in each magnification
ratio.
FO-DC550 ELECTRICAL SECTION 13 - 9
Scanner Motor Driver
(10-D2)
(10-D2)
(10-D2)
(10-D2)
OUT_AOUT_A+
OUT_B+
OUT_B-
24VM
5V
R89
R90
1
PGND
2
(2-A3)
MM_BI0
(2-A3)
MM_BI1
(2-A3) MM_PH_B
1
1
R93
1kJ
24
23
22
21
20
19
18
17
16
15
14
13
VS
SENSE 1
COMP 1
OUT 1B
I01
GND
GND
I11
PHASE 1
VREF 1
RC 1
VSS
MM_AI0
1
L6219DS or AMM56219
R94
30kJ
R95
30kJ
C118
820p
2
1
2
PGND
PGND
PGND
PGND
1
2
2
2
MMref0
MMref1
MMref2
C121
0.1u
2
(5-C1)
(5-C1)
(5-C1)
PGND
5V
C119
0.1u
R98
510J
2
2
2
1
1
1
R97
1kJ
1
C115
820p
(2-A3)
MM_AI1
(2-A3)
MM_PH_A (2-A3)
2
2
C117
820p
OUT 1A
OUT 2A
SENSE 2
COMP 2
OUT 2B
GND
GND
I02
I12
PHASE 2
VREF 2
RC 2
2
1
2
3
4
5
6
7
8
9
10
11
12
C116
820p
5V
R96
2kJ
2
0.68J
1W
R91
1.5kJ
IC29
2
1
R92
1.5kJ
1
1
0.68J
1W
1
2
1
1
PGND
PGND
SPF Motor Driver
C125 2200p
1
1
R99
2
2
7.5kJ
R100 7.5kJ
1
1
C126
2
2
2200p
C127 OPEN
1
PGND
2
2
2
23
20
25
3
24
19
12
18
2
2200p
PGND
2
2W
R115
1kJ
2
OPEN
Vmm
CrA
CrB
VsA
RsA
VrefA
VrefB
RsB
VsB
OUT /A
OUT A
OUT /B
OUT B
In /A
In A
In /B
In B
PG
PG
22
1
4
14
11
SPMT_2
SPMT_0
SPMT_3
SPMT_1
(11-E1)
(11-D1)
(11-D1)
(11-E1)
15
28
C136
OPEN
MTD1361/F
2
2
PGND
1
C137
26
27
17
16
2200p
1
1
R114 1J
C135
1
1
2
R111 2.4kJ
2
1
0.1u
1
MRPS_1
MRPS_2
MRPS_3
C134
2
1
2
R110
100J
2
R109
1.2kJ
2
2
(5-C2)
(5-C2)
(5-C2)
1
1
1
R108
620J
R107
300J
2
24VM
OPEN
IC31
R104 2.4kJ
1
C130
C132
1
1
R101
1kJ
2W
2
R103 1J
R102
750J
2
1
1
1
5V
PGND
PGND
(4-D3)
(4-D3)
(4-D3)
(4-D3)
(SPFMT2)
(SPFMT0)
(SPFMT3)
(SPFMT1)
Duplex Motor Driver
Shifter Motor Driver
IC28
(1-D3)
(1-D3)
(1-D3)
(1-D3)
3
4
5
6
10
11
12
13
14
15
DMT0
DMT1
DMT2
DMT3
17
18
I1
NC
NC
I2
NC
I3
NC
NC
I4
NC
GND
GND
O1
O2
O3
O4
2
7
9
16
IC30
/DMT0
(11-B3)
/DMT1
(11-B3)
(4-B2) SFTMT0
/DMT2
(11-B3)
(4-B2) SFTMT1
/DMT3
(11-B3)
(4-B2) SFTMT2
24VDup
(4-B2) SFTMT3
COM
COM
TD62064AF
1
8
D5
R338 1
0J
2
R339 1
0J
R340 1
0J
2
R341 1
0J
2
2
3
4
5
6
10
11
12
13
14
15
17
18
MTZ J22B
I1
NC
NC
I2
NC
I3
NC
NC
I4
NC
GND
GND
O1
O2
O3
O4
2
7
9
16
PGND
FO-DC550 ELECTRICAL SECTION 13 - 10
/SFTMT1 (11-A1)
/SFTMT2 (11-A1)
/SFTMT3 (11-A1)
24VSFT
COM
COM
1
8
TD62064AF
PGND
/SFTMT0 (11-A1)
D6
MTZ J22B
(10) OPE PWB
(11) Carriage Unit
a. Outline
a. Outline
The operation circuit is composed of the LCD control circuit, the key
matrix circuit, the display matrix circuit, and the buzzer circuit, realizing
the U/I functions.
The carriage unit is provided with the CCD PWB, the inverter PWB, the
lamps, etc. A document is radiated, and image data read by the CCD
are A/D converted to be sent to the ASIC.
b. LCD control circuit
b. CCD PWB
The character LCD (COG) in 2 lines and 16 digits is used. The display
data are sent from the MCU (CPU) to LCD internal registers, controlling the LCD.
The color image sensor uPD8861 (5400 pixels x 3 lines) is used as the
CCD on the CCD PWB to scan images in the resolution of 600dpi/US
letter size in the main scanning direction.
c. Key matrix circuit
The SEL signal is sent from the CPU of MCU to the matrix selector IC
(multiplexer) in the operation circuit. The signal detects OFF/ON of the
key, and is sent to the CPU as serial data.
Image data scanned by the CCD are inputted to AFE (AD9826), where
they are A/D-converted to output digital data. The output digital data
are sent to the MCU PWB and to the ASIC. The ASIC performs image
process with the digital data.
d. LED matrix circuit
c. Lamp inverter PWB
The display is controlled by inputting the serial data signal, the clock
signal, and the latch signal from ASIC to the LED driver in the operation circuit.
The transformer is controlled by the lamp control signal from the MCU
PWB to turn ON/OFF the cool cathode ray tube by the transformer output.
In the LED driver, data are set to the register (8bit) and latched to control the IC output port, performing matrix-driving of ON/OFF of the LED.
B. DC power circuit
The DC power circuit directly rectifies the AC power and performs
switching-conversion with the DC/DC converter circuit, and rectifies
and smoothes again to generate a DC voltage.
The constant voltage control circuit is of +5VEN. +24V and +12V are of
the non-control system by winding from the +5VEN winding. As shown
in fig (1), +24V, +12V, and +5V are provided with the ON/OFF function
by external signals. +3.3V is outputted from +5VEN to the regulator IC.
Refer to the block diagram, fig (1).
Rush current
prevention circuit
Rectifying/
smoothing
circuit
Noise filter
circuit
Inverter circuit
(Ringing choke converter system)
Rectifying/
smoothing circuit
(Semiconductor switch)
+12V regulator IC
(with ON/OFF function)
Rectifying/
smoothing circuit
(Semiconductor switch)
Overcurrent
protection circuit
Control
circuit
Constant-voltage
detection circuit
+3.3V
regulator IC
fig (1) Block diagram
(1) Noise filter circuit
The filter circuit is composed of L and C. It reduces common noises
and normal mode noises generated from the AC line.
(2) Rush current prevention circuit and rectifying/
smoothing circuit
The common noise means that generated in each line for GND. Its
noise component is delivered through C002, C003, and C022 to GND.
The normal noise means that overlapped in the AC line or the output
line. It is attenuated by C023, C001, L002, C004, and L003. Refer to fig
(2).
fig (3) Rush current prevention, rectifying/smoothing circuit
fig (2) Noise filter circuit
FO-DC550 ELECTRICAL SECTION 13 - 11
Since the AC power is directly rectified, if there were not this rush current prevention resistor (TH001), an extremely large rush current
would flow due to a charging current flowing through the smoothing
capacitor C006 when turning on the power.
Q001
VDS waveform
To prevent against this, the rush current prevention resistor TH001 is
provided between the rectifying diode D003 and the smoothing diode
C006, suppressing a rush current.
The rectifying/smoothing circuit rectifies a 60Hz AC voltage with the
rectifying circuit, and smoothes it with the smoothing capacitor C006.
(3) Inverter and control circuit (Ringing choke converter
system)
ID
Q001
ID waveform
Np
Secondary output side
D706 D113
ID waveform
Nc
Fig. (5) Ringing choke converter operation waveforms
When Q001 turns off, energy accumulated in the transformer (T001)
flows a current of waveform C in the path indicated with dotted line as
shown in the figure above through D101 and D113 and dissipates to
the secondary output side. When this energy is exhausted, the current
flowing through D101 and D113 turns off. However, the NS winding has
a slight remaining energy, which generates a voltage in the base winding NC and turns on Q001 again to repeat switching operation, supplying a high frequency power to the secondary side.
Ns
(4) Overcurrent protection circuit (Primary side)
The ON period extension due to an increased output load is detected,
and the OFF period of Q001 is extended by the control circuit, and
energy accumulated in the primary winding of the transformer T001 is
reduced, providing protection against an overcurrent. Refer to Fig. (4).
(5) Rectifying/smoothing circuit (+5V)
Fig. (4) Inverter and control circuit
When the power is supplied to this circuit, the DC voltage, Vref, supplied by the rectifying/smoothing circuit is applied through R006 and
R007 to FET (Q001), turning on Q001.
When Q001 is turned on, the drain current, ID, flows as the waveform B
in Fig. (5) to apply VDC to the main winding, NP, on the primary side.
At the same time, a voltage is generated in NC winding and applied
through R005 and C008b to the gate of Q001. As a result, Q001 is
turned on rapidly.
At the same time with this, C009 is charged through D001, R001, and
D012. When the potential of C009 reaches 0.7V (= VBE of Q002), Q002
turns on to turn off Q001.
fig (6) Rectifying/smoothing circuit
The high frequency pulse generated by the inverter circuit is
decreased by the converter transformer, rectified by the high frequency
diode D113, and smoothed by C107 and C108.
Voltage waveform
Voltage waveform
fig (7) +5V rectifying/smoothing circuit voltage waveform
FO-DC550 ELECTRICAL SECTION 13 - 12
[14] CIRCUIT DIAGRAM
1. MCU PWB
A
B
C
MCU PWB (CPU section)
VCC3
When IC1 is,
mounted
R4(*3)
OPEN
0J
R3(*1)
OPEN
680J
R7(*4)
22J
OPEN
R2(*2)
0J
OPEN
4
NOT mounted
C3(*5)
22pF
15pF
C1(*6)
22pF
15pF
Spreading Range :
+/- 1.25%
R1
OPEN
IC1
8
7 VDD
6 SR0
5 MODOUT
SSon
VCC3
C2
0.1u
R2
1
Xin 2
Xout 3
FS0 4
Vss
*2
R3
*1
X1
HC-49U/S
19.6608MHz
P2010/PLL701-01
R5
0J
*R2,R3,C1, and C3 are tentative
C1
*6
R4
R6
0J
C3
*5
*3
R7
*4
C4
SELIN3
SELIN2
SELIN1
ESS_TS
(8-A3)
ES_CMD
(8-A3)
(8-A2) /ESS_RDY
(8-A2) /ESC_RDY
R8
R9
R10
33J
33J
100J
ESS_TS
ES_CMD
/ESS_RDY
/ESC_RDY
/WDTOVF
(4-C2)
(4-C2)
(4-C2)
/PRINTST
RD
HWR
LWR
/STBY
NMI
/PRINTST
/RD
/HWR
/LWR
CPUCLK(NC)
(2-E3)
(13-B2) (3-A2) (2-C1)
(3-A2) (4-A2)
(2-C1)
/RESET1
12p
VCC3
(SIN1)
(SIN2)
(SIN3)
(4-D4) (KEYIN)
(13-B2) MSU_ST1
C386
OPEN
(4-C3)
SPFMT3
SPFMT2
SPFMT1
SPFMT0
PSL
5
6
7
8
BR110
4
3
2
1
/CS3#
/CS2#
/CS1#
/CS0#
PE
PE
P
PE
1
R21
1
2
3
BR24 4
33J
8
7
6
5
1
2
3
4
33J
RESETOUT1
R22
10kJ
A
(2-C4)
C23
OPEN
1
2
3
4
/RESET0
C22
0.1u
M51957BFP
A12
A13
A14
A15
A16
A17
A18
A19
8
7
6
5
1
2
3
4
NC
NC
IN
VCC
NC OUT
GND Cd
A4
A5
A6
A7
A8
A9
A10
A11
R19
3.3kJ
IC4
1
2
3
4
BR23
33J
8
7
6
5
1
2
3
4
R18
11kF
R20
10kF
PD
PD2
PD
PD
PE
PE
PE
PE
VCC3
A0
A1
A2
A3
C24
0.1u
102
101
100
99
98
97
96
95
94
93
92
91
90
89
88
87
86
85
84
83
82
81
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
BR20
33J
8
7
6
5
VCC3
PD7
PD6
PD5
PD4
33J
Reset IC
VCC3
HD6412321VF25(H8S/2321)
P35/
P34/
P33/
P32/
P31
P30/
C384
OPEN
C381
22pF
C382
OPEN
C383
OPEN
/CS3
/CS2
/CS1
/CS0
2
R337
33J
/SCANSP
/SCANST
/TRANSST
/SCANSP
(2-D2)
/SCANST
(2-E3)
/TRANSST
(2-E3)
PMCLK
(5-B2)
SPFMT3
(4-C2)
(4-C3) SPFMT2/MIRCNT
SPFMT1
(4-C3)
SPFMT0
(4-C3)
AVcc
Vref
P40/AN0
P41/AN1
P42/AN2
P43/AN3
P44/AN4
P45/AN5
P46/AN6/DA0
P47/AN7/DA1
AVss
Vss
P17/PO15/TIOCB2/TCLKD
P16/PO14/TIOCA2
P15/PO13/TIOCB1/TCLKC
P14/PO12/TIOCA1
P13/PO11/TIOCD0/TCLKB
P12/PO10/TIOCC0/TCLKA
P11/PO9/TIOCB0/DACK1
P10/PO8/TIOCA0/DACK0
MD0
MD1
MD2
PG0/CAS
PG1/CS3
PG2/CS2
BR22
33J
8
7
6
5
(4-D4)
(4-D4)
(4-D4)
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
BR21
33J
8
7
6
5
RTH
P53/ADTRG
P52/SCK2
Vss
Vss
P51/RxD2
P50/TxD2
PF0/BREQ
PF1/BACK
PF2/LCAS/WAIT/BREQO
PF3/LWR
PF4/HWR
PF5/RD
PF6/AS
VCC
PF7/0
Vss
EXTAL
XTAL
VCC
STBY
NMI
RES
WDTOVF
P20/PO0/TIOCA3
P21/PO1/YICOB3
P22/PO2/TIOCC3
P23/PO3/TIOCD3
P24/PO4/TIOCA4
P25/PO5/TIOCB4
P26/PO6/TIOCA5
P27/PO7/TIOCB5
P63/TEND1
P62/DREQ1
P61/TEND0/CS5
Vss
Vss
P60/DREQ0/CS4
Vss
10kJ
R13
/ES_PAGE
(5-E3)
PG3/CS1
PG4/CS0
Vss
NC
VCC
PC0/A0
PC1/A1
PC2/A2
PC3/A3
Vss
PC4/A4
PC5/A5
PC6/A6
PC7/A7
PB0/A8
PB1/A9
PB2/A10
PB3/A11
Vss
PB4/A12
PB5/A13
PB6/A14
PB7/A15
PA0/A16
PA1/A17
PA2/A18
PA3/A19
Vss
PA4/A20/IRQ4
PA5/A21/IRQ5
PA6/A22/IRQ6
PA7/A23/IRQ7
P67/CS7/IRQ3
P66/CS6/IRQ2
Vss
Vss
P65/IRQ1
P64/IRQ0
10kJ
10kJ
R12
IC2
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
(8-A2)
R11
3
/ASIC_RST (2-D1) (8-A1) (9-B2)
C25
47p
B
FO-DC550 CIRCUIT DIAGRAM 14 - 1
C
C
D
E
1/14
VCC3
BR1
/STBY
NMI
/WDTOVF
C5
100p
BR4
8
7
6
5
1
2
3
4
C6
100p
RY/BY
/CS4#
1
2
3
4
/ESC_RDY
/ESS_RDY
ES_CMD
ESS_TS
1
2
3
4
/PRINTST
D15
D14
D13
D12
1
2
3
4
RY/BY
R331
33J
/CS4#
10kJ
10kJ
BR6
BR7
8
7
6
5
D11
D10
D9
D8
1
2
3
4
8
7
6
5
D7
D6
D5
D4
1
2
3
4
LCDDB6
LCDDB7
BZR
LCDDB5
LCDDB4
RY/BY
/CS4
(4-C1)
(4-C1)
(4-C3)
(4-C1)
(4-C1)
(3-B2)
(13-B2)
ARB_INT
(FW)
CPU_SYNC
mt_at_home
1
2
3
4
8
7
6
5
CCD_TG
(SPPD)
(PSW)
A20
1
2
3
4
10kJ
10kJ
BR10
10kJ
8
7
6
5
10kJ
1
2
3
4
D3
D2
D1
D0
8
7
6
5
BR9
BR2
8
7
6
5
8
7
6
5
CPUCLK(NC)
RD
HWR
LWR
4
3
2
1
POFF
TxD1
SDA
SCL
4
3
2
1
/TRANSST
/SCANST
/SCANSP
1
2
3
4
10kJ
BR11
5
6
7
8
10kJ
BR12
5
6
7
8
10kJ
BR13
8
7
6
5
3
64
63
62
61
60
59
58
57
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41
40
39
SPFMT3
SPFMT2
SPFMT1
SPFMT0
4
3
2
1
(SIN1)
(SIN2)
(SIN3)
(KEYIN)
4
3
2
1
LCDE (4-C1)
LCDRS (4-C1)
SCL
SDA
TXD1
POFF
1
2
3
4
1
2
3
4
8 BR14
7 33J
6
5
8 BR16
7 33J
6
5
D11
D10
D9
D8
D7
D6
D5
D4
1
2
3
4
8 BR19
7 33J
6
5
D3
D2
D1
D0
5
6
7
8
10kJ
TxD1 (11-B2)
POFF (5-B1)
D15
D14
D13
D12
1
2
3
4
8 BR17
7 33J
6
5
BR15
BR18
5
6
7
8
10kJ
D[15..0] (2-A1) (3-A1) (4-A2) (13-C2)
38
65/ Q
P64/IRQ0
Q
Vss
65
10kJ
P35/SCK1
P34/SCK0
P33/RxD1
P32/RxD0
P31/TxD1
P30/TxD0
VCC
PD7/D15
PD6/D14
PD5/D13
PD4/D12
Vss
PD3/D11
PD2/D10
PD1/D9
PD0/D8
PE7/D7
PE6/D6
PE5/D5
PE4/D4
Vss
PE3/D3
PE2/D2
PE1/D1
PE0/D0
VCC
4
10kJ
BR8
10kJ
1
2
3
4
DMT0
DMT1
DMT2
DMT3
8
7
6
5
C385
OPEN
CPU3.3
(6-D4)
(6-D4)
(6-D4)
(6-D4)
8
7
6
5
BR3
BR94
DMT0
DMT1
DMT2
DMT3
1
2
3
4
10kJ
10kJ
DMT0
DMT1
DMT2
DMT3
RESETOUT1
BR5
/CS0#
/CS1#
/CS2#
/CS3#
8
7
6
5
H8S/2321
2
Serial EE-PROM
VCC3
ARB_INT
(FW)
CPU_SYNC
MT_HOME
CCD_TG
(SPPD)
(PSW)
A20
ARB_INT (2-B1)
(4-D4) (8-A2)
(FW)
CPU_SYNC (2-B1)
mt_at_home (14-C3)
(2-A4) (14-D3)
CCD_TG
(7-E1)
(SPPD)
(7-E1)
(PSW)
VCC3
VCC3
C7
0.1u
SCL
SDA
R15
1kJ
R16
1kJ
IC3
8
7
6
5
VCC
E0
WC
E1
SCL
E2
SDA VSS
R14
10kJ
1
2
3
4
R17
OPEN
24WC02
SCL (4-A1)
SDA1 (4-B1)
A[19..0] (2-A1) (3-A3)
L1
ZJSR5101-223
VCC3
C
FO-DC550 CIRCUIT DIAGRAM 14 - 2
0.1u
0.1u
0.1u
0.1u
C14
C13
C12
0.1u
D
C11
C10
C9
0.1u
CPU3.3
C8
+
1
10u/16V
E
A
B
C
MCU PWB (ASIC section)
33J
R27
33J
R29
33J
R30
33J
R31
33J
AFE_SDI
C48
C49
C50
C51
C52
C53
C54
47p
47p
47p
47p
47p
47p
47p
47p
8
7
6
5
VCC3
MM_BI0
MM_BI1
MM_BI2
(6-B3) MM_PH_A
MM_AI0
(6-B3)
MM_AI1
(6-B3)
MM_AI0
MM_AI1
MM_AI2
1
2
3
4
BR39
1
2
3
4
BR41
1
2
3
4
BR43
8
7
6
5
1
2
3
4
BR45
RAMDB3
1
RAMDB2
2
RAMDB1
3
4
RAMDB0
BR49
RAMDB15
1
2
RAMDB14
3
RAMDB13
RAMDB12
4
BR52
1
RAMDB11
RAMDB10
2
RAMDB9
3
4
RAMDB8
BR56
1
(3-E2) DQM1
2
(3-E2) SDCKE
3
4
BR60
1
MAD12
MAD11
2
3
MAD9
4
MAD8
BR62
MAD7
1
2
MAD6
3
MAD5
MAD4
4
BR63
RAM_CLK_OUT
8
7
6
5
MAD3
MAD2
MAD1
MAD0
MAD10
(3-E3) RAMDB[15..0]
BANK1
BANK0
/SDCS
(3-D2)
(3-D2)
(3-D2)
(3-D2)
/SDRAS
/SDCAS
/SDWDE
DQM0
RAMDB7
RAMDB6
RAMDB5
RAMDB4
VCC3
BR48
1
2
3
4
10kJ
8
7
6
5
RAMDB7
RAMDB6
RAMDB5
RAMDB4
BR53
1
2
3
4
10kJ
8
7
6
5
RAMDB3
RAMDB2
RAMDB1
RAMDB0
BR57
1
2
3
4
10kJ
8
7
6
5
RAMDB15
RAMDB14
RAMDB13
RAMDB12
BR61
1
2
3
4
10kJ
8
7
6
5
RAMDB11
RAMDB10
RAMDB9
RAMDB8
(3-E2) SDCLK
R351
33J
8
7
6
5
8
7
6
5
8
7
6
5
8
7
6
5
8
7
6
5
8
7
6
5
8
7
6
5
8
7
6
5
33J
33J
33J
33J
33J
33J
33J
82J
33J
33J
C397
0.1u
X2
8
C67
0.1u
1
1
VCC
OUTPUT
N.C.
GND
5
4
C68
12p
R43
33J
SFCLK48
ASIC
HG73C138HFV
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
ZJSR5101-223
0J
X3
(3-A3) (1-C1) A[19..0]
0J
12p
A
B
FO-DC550 CIRCUIT DIAGRAM 14 - 3
ARB_INT
PFCLKOUT
R45
C70
(13-C2)(4-A2)
(3-A1) (1-D2) D[15..0]
PFCLKIN
A9
A8
A7
A6
R44
MEM_INT
HC-49U/S (16.1511MHz)
(1-D2)
12p
(4-C3)
MIRCNT
(1-D2) CPU_SYNC
C69
D3
D2
D1
D0
OSC-31
48MHz
D15
D14
D13
D12
D11
D10
D9
D8
L3
C66
22000p
VCC3
D7
D6
D5
D4
2
(3-D2)
(3-D2)
(3-D2)
GND(CORE)
MM_Y3
MM_Y2
MM_Y1
VCC(CORE)
MM_PH_B
MM_BI0
MM_BI1
MM_BI2
MM_PH_A
MM_AI0
MM_AI1
MM_AI2
GND(AC)
RAM_MAD3
RAM_MAD2
GND(CORE)
RAM_MAD1
RAM_MAD0
RAM_MAD10
VCC(CORE)
RAM_BANKS1
RAM_BANKS0
RAM_CS
RAM_RAS
RAM_CAS
VCC(AC)
RAM_WDE
RAM_DQM0
GND(AC)
RAM_DATA7
RAM_DATA6
RAM_DATA5
RAM_DATA4
GND(CORE)
RAM_DATA3
RAM_DATA2
RAM_DATA1
RAM_DATA0
GND(AC)
RAM_DATA15
RAM_DATA14
VCC(CORE)
RAM_DATA13
RAM_DATA12
RAM_DATA11
RAM_DATA10
RAM_DATA9
RAM_DATA8
VCC(CORE)
RAM_DQM1
RAM_CKE
GND(AC)
RAM_CLK_OUT
GND(CORE)
RAM_MAD12
RAM_MAD11
RAM_MAD9
VCC(CORE)
RAM_MAD8
RAM_MAD7
VCC(AC)
RAM_MAD6
RAM_MAD5
RAM_MAD4
GND(AC)
CPUDATA15
CPUDATA14
CPUDATA13
CPUDATA12
CPUDATA11
CPUDATA10
CPUDATA9
CPUDATA8
PFCLKOUT
PFC LKIN
(3-E1) MAD[12..0]
(6-B3) MM_PH_B
MM_BI0
(6-B3)
MM_BI1
(6-B3)
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
SFCLK48
MM_AI1
MM_AI2
10kJ
10kJ
MM_Y3
MM_Y2
MM_Y1
(5-B1)
(5-B1)
(5-B1)
(1-A2) /CS2
R33
R34
MM_BI0
MM_BI1
MM_BI2
MM_AI0
8
7
6
5
RAM_CLK_OUT
A5
A4
A3
A2
A1
3
10kJ
8
7
6
5
1
2
3
4
CL
IC5
BR33
1
2
3
4
8
7
6
5
222
221
220
219
218
217
216
215
214
213
212
211
210
209
208
207
206
205
204
203
202
201
200
199
198
197
196
195
194
193
192
191
190
189
188
187
186
185
184
183
182
181
180
179
178
177
176
175
174
(14-A4)
1
2
3
4
CLPWM
VCC(AC)
AFE_DB0
AFE_DB1
AFE_DB2
AFE_DB3
AFE_DB4
AFE_DB5
AFE_DB6
AFE_DB7
GND(AC)
AFESCK
VCC(CORE)
ADCLK
GND(CORE)
AFE_SEN
CCD_PH1
CCD_PH2
AFE_SDI
CCD_CP
BSAMP
CCD_RS
CCD_TG
VSAMP
GND(CORE)
TD0
TDI
TRSK
TMS
TCK
VCC(CORE)
/INREQ
/OUTCS
/OUTACK
/ESPRD
/FAXPRD
/PCLPRD
GND(AC)
MDAT15
MDAT14
MDAT13
VCC(CORE)
MDAT12
MDAT11
MDAT10
VCC(AC)
MDAT09
MDAT08
MD T0
AFE_DB7
AFE_DB6
AFE_DB5
AFE_DB4
10kJ
AFE_DB3
8
AFE_DB2
7
AFE_DB1
6
AFE_DB0
5
10kJ
10kJ AFE_SDI
1
2
3
4
BR29
1
2
3
4
BR31
R32
BR27
AFE_DB7 33J
AFE_DB6
AFE_DB5
AFE_DB4
BR30
AFE_DB3 33J
AFE_DB2
AFE_DB1
AFE_DB0
JTG _TDO
JTG_ TDI
C47
BR9
4
3
2
1
CPU_DATA7
CPU_DATA6
CPU_DATA5
CPU_DATA4
VCC(AC)
CPU_DATA3
CPU_DATA2
CPU_DATA1
CPU_DATA0
GND(AC)
MIRCNT
/CPUSYNC
MEM_INT
ARB_INT
VCC(CORE)
CPU_AD8
CPU_AD7
CPU_AD6
CPU_AD5
GND(CORE)
RAM_CLK_IN
CPU_AD4
CPU_AD3
CPU_AD2
CPU_AD1
CPU_AD0
/CPUCS
SFCLK48
GND(CORE)
/CPUWR
/CPURD
/RESET
VCC(CORE)
PFCLK
CLKSW
GND(CORE)
PFCLKOUT
PFCLKIN
GND(PLL)
VCC(PLL)
GND(PLL)
VCC(PLL)
TM2_15M
/SYNC
GND(AC)
/VIDEO
/LEND
VCC(AC)
OUTP00
VCC3
JTG_TCK
JTG_TMS
JTG_TDI
JTG_TDO
/OUTCS
PFC LK
CLKSW
(14-A2) ADCLK
(14-A2) AFE_SCK
(14-A3) AFE_DB[7..0]
BR2
4
3
2
1
/IN REQ
/OU TCS
/OU TACK
/ESPRD
/FA XPRO
/PCLPRO
(14-A2) AFE_SEN
JTG _TMS
JTG_TCK
(14-D3) CCD_PHI2
(14-D3) CCD_PHI1
/RESET0 (1-B1) (3-B2)
(14-A2) AFE_SDI
/PCLPRO
/FAXPRO
/OUTACK
/INREQ
MMD
R26
(1-B3) /LWR
(13-B2) (3-A2) (1-B3) /RD
(8-A1) (1-B1) (/ASI C_RST)
(9-B2)
4
33J
(5 B1)
(14-D3) CCD_CP
33J
R25
SYNC#
(14-A2) BSAMP
33J
R24
VIDEO#
/LEND
(14-D3) CCD_RS
R23
(4-C1)
(5-B1)
(14-A2) VSAMP
(1-D2),(14-D3) CCD_TG
C
C
D
E
2/14
VCC3
0.1 u
0.1 u
0.1 u
0.1 u
0.1 u
0.1 u
0.1 u
0.1 u
0.1 u
0.1 u
+
47u/16V
C35
C34
C33
C32
C31
C30
C29
C28
C27
C26
C36
4
0.1 u
0.1 u
0.1 u
C64
C46
0.1 u
0.1 u
C63
C45
0.1 u
0.1 u
C62
C44
0.1 u
0.1 u
C61
C43
0.1 u
0.1 u
C60
C42
0.1 u
0.1 u
C59
C41
0.1 u
0.1 u
C58
C40
0.1 u
C39
0.1 u
/H_SYNC (8-A2)
C57
PIDATA4
PIDATA5
PIDATA6
PIDATA7
0.1 u
PIDATA0
PIDATA1
PIDATA2
PIDATA3
C38
1
2
3
4
10KJ
8
7
6
5
BR26 33J
8
7
6
5
BR28 33J
C37
1
2
3
4
R28
0.1 u
PIDATA[7..0] (8-A4)
0.1 u
10KJ
5
6
7
8
G3.3V
0.1 u
BR93
4
3
2
1
VCC3
L2
ZJSR5101-102TA
C56
10KJ
5
6
7
8
C55
BR25
4
3
2
1
VCC(AC)
MDAT09
MDAT08
MDAT07
GND(CORE)
MDAT06
MDAT05
MDAT04
VCC(CORE)
MDAT03
MDAT02
MDAT01
MDAT00
GND(AC)
/INCS
/INACK
/OUTREQ
GND(CORE)
/HSYNC
PIDATA0
PIDATA1
PIDATA2
VCC(AC)
PIDATA3
PIDATA4
PIDATA5
PIDATA6
PIDATA7
/POCS
177
176
175
174
173
172
171
170
169
168
167
166
165
164
163
162
161
160
159
158
157
156
155
154
153
152
151
150
149
C65
G3.3V
8
7
6
5
BR32 33J
8
7
6
5
BR34 33J
1
2
3
4
/POREQ
(8-A2)
/PIW R
/PIACK
/POACK
/PIREQ
(8-A4)
(8-A4)
(8-A2)
(8-A4)
3
PODATA[7..0] (8-A2)
PODATA0
PODATA1
PODATA2
PODATA3
PODATA4
PODATA5
PODATA6
PODATA7
VCC3
R35
10kJ
R310
10J
/PR_LINE (8-A2)
R311
10J
/SC_LINE (8-A2)
/TRANSST (1-A2)
/PRINTST (1-B3)
/SCANST (1-A2)
RCV
VPIN
VMIN
1
2
3
4
8
7
6
5
BR44 33J
8
7
6
5
BR47 33J
8
7
/REV
6
5
/FAULT
BR51 33J
/ACK
8
7
BUSY
6
PE
SLCT
5
BR55 33J
8
/INIT
7
/SLCTIN
/AUTOF D
6
5
/STB
BR58 33J
1
2
3
4
1
2
3
4
1
2
3
4
1
2
3
4
/SCANSP
(4-C3)
OP_CLK
(4-C3)
PARAD2
PARAD3
PARAD4
PARAD5
PARAD6
PARAD7
/REV
/FAULT
(12-A3)
(12-A3)
/ACK
BUSY
PE
SLCT
(12-A3)
(12-A3)
(12-A3)
(12-A3)
/INIT
/SLCTIN
/AUTOF D
/ST B
(12-A3)
(12-A3)
(12-A3)
(12-A3)
VCC3
PARAD[7..0] (12-A3)
VCC3
MEM_INT
CLKSW
/POREQ
/PIREQ
BR35
1
2
3
4
10kJ
8
7
6
5
PODATA0
PODATA1
PODATA2
PODATA3
BR37
1
2
3
4
10kJ
8
7
6
5
PODATA4
PODATA5
PODATA6
PODATA7
BR40
1
2
3
4
10kJ
8
7
6
5
2
VCC3
VCC3
OP_LATCH (4-C3)
OP_DATA (4-C3)
TM
(4-C2)
TM_
(4-C2)
R37
10kJ
/IMC_READY (8-A2)
KEYSC3 (4-C2)
KEYSC2 (4-C2)
KEYSC1 (4-C2)
SPFO N (4-C2)
MIRON (4-C2)
(5-B3)
MPFS
HL
PR
CPFS2
VCC3
PARAD0
PARAD1
R38
OPEN
R39
OPEN
PFCLK
R40
OPEN
R41
10kJ
BR46
1
2
3
4
10kJ
8
7
6
5
PARAD0
PARAD1
PARAD2
PARAD3
BR50
1
2
3
4
10kJ
8
7
6
5
PARAD4
PARAD5
PARAD6
PARAD7
BR54
1
2
3
4
10kJ
8
7
6
5
/INIT
/SLCTIN
/AUTOF D
/STB
BR59
1
2
3
4
10kJ
8
7
6
5
RCV
VPIN
VMIN
R42
10kJ
(5-B2)
(5-B3)
(5-B3)
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
/VIDEO
/LEND
VCC(AC)
OUTP00A
OUTP01A
OUTP02A
OUTP03A
OUTP04A
OUTP05A
OUTP06A
OUTP15A
VCC(CORE)
OUTP07A
OUTP08A
GND(CORE)
OUTP09A
OUTP10A
OUTP11A
OUTP12A
OUTP13A
VCC(CORE)
OUTP14A
OUTP00B
GND(AC)
OUTP01B
OUTP02B
OUTP03B
OUTP04B
VCC(AC)
/POREQ
VCC(AC)
/PIWT
/PIACK
GND(AC)
/POACK
/PIREQ
GND(CORE)
PODATA0
PODATA1
PODATA2
PODATA3
PODATA4
PODATA5
PODATA6
PODATA7
VCC(CORE)
/TRANSST
/RECEPTST
/PRINTST
/SCANST
RCV
VPIN
VMIN
GND(CORE)
VPOUT
VMOUT
OEN
GND(AC)
SUSPEND
IE1284_PARAD0
IE1284_PARAD1
VCC(AC)
IE1284_PARAD2
IE1284_PARAD3
IE1284_PARAD4
IE1284_PARAD5
IE1284_PARAD6
IE1284_PARAD7
IE1284_REV
VCC(CORE)
IE1284_FAULT
IE1284_ACK
IE1284_BUSY
IE1284_PE
GND(CORE)
IE1284_SLCT
IE1284_INIT
IE1284_SLCTIN
VCC(CORE)
IE1284_AUTOFD
IE1284_STB
TSP_MODE
TSO0
/SCANSP
VCC(AC)
OPE_CLK
GND(AC)
OPE_LATCH
OPE_DATA
TM
/TM
VCC(CORE)
OUTP14B
OUTP13B
OUTP12B
OUTP11B
OUTP10B
OUTP09B
OUTP08B
GND(CORE)
OUTP07B
OUTP06B
OUTP05B
1
2
3
4
148
147
146
145
144
143
142
141
140
139
138
137
136
135
134
133
132
131
130
129
128
127
126
125
124
123
122
121
120
119
118
117
116
115
114
113
112
111
110
109
108
107
106
105
104
103
102
101
100
99
98
97
96
95
94
93
92
91
90
89
88
87
86
85
84
83
82
81
80
79
78
77
76
75
VCC3
1
R352 33J
(/ASIC_RST)
R353 N.M.
R358
10kJ
/RESET1
R354 N.M.
C
DEVDIR
SPFS
SRRC
SGS
SPUS
RRS
LDEN
MRPS1
MRPS2
MRPS3
CPFS1
(5-B3)
(5-B2)
(5-B2)
(5-B2)
(5-B2)
(5-B3)
VFM
/FPOFF
(4-A1)
VFMCNT
(5-B3)
(5-B3)
MMD
PMD
TC
GRID L
MC
BIAS
(5-B1)
(5-B1)
(5-B4)
(5-B4)
(5-B4)
(5-B4)
(4-C1)
(5-B1)
VIDEO#
/LEND
/OA_RST (9-B2)
R355
N.M.
/FWREN
C398
47p
D
FO-DC550 CIRCUIT DIAGRAM 14 - 4
SYNC#
C71
47p
R46
(/SYNC) (4-D4)
10J
E
A
B
C
MCU PWB (Memory section)
4
(1-C1) (2-A1) A[19..0]
3
10kJ
0J
R47
R48
VCC3
V
R49
10kJ
IC7
IC8
5
28
12
CS1
OE
WE
A16
A15
A14
A13
A12
A11
A10
A9
D8
D9
D10
D11
D12
D13
D14
D15
6
7
10
11
22
23
26
27
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
HWRZ
/RESET0
VCC3 VCC3
VDD
VDD
GND
GND
A19
A18
A8
A7
A6
A5
A4
A3
A2
8
24
9
25
C73
C74
0.1u
0.1u
A17
A1
IS63LV1024L-12J-TR
(1-D3) RY/BY
R51
0J
OPEN
CS1Z
RDZ
HWRZ
I/O0
I/O1
I/O2
I/O3
I/O4
I/O5
I/O6
I/O7
OPEN
(1-A2) /CS1
/RD
(15-B2) (2-C1) (1-B3)
(1-B3) /HWR
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
A16
R53
2
1
2
3
4
13
14
15
16
17
18
19
20
21
29
30
31
32
R52
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
A16
A15
A14
A13
A12
A11
A10
A9
A8
NC
NC
WE
RP
VPP
WP
RY/BY
NC
A17
A7
A6
A5
A4
A3
A2
A1
A16
BYTE
GND
DQ15
DQ7
DQ14
DQ6
DQ13
DQ5
DQ12
DQ4
VCC
DQ11
DQ3
DQ10
DQ2
DQ9
DQ1
DQ8
DQ0
OE
GND
CE
A0
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
Flash ROM
(15-C2) (4-A2) (2-A1) (1-D2) D[15..0]
Flash ROM
IC7
R51
LH28F400BVE-BL85
OPEN
1
A
B
FO-DC550 CIRCUIT DIAGRAM 14 - 5
C
C
D
E
3/14
4
RAMDB[15..0] (2-A2)
3
VCC3
VCC3
IC6
VCC3
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
RAMDB0
RAMDB1
RAMDB2
R49
10kJ
RAMDB3
RAMDB4
RAMDB5
RAMDB6
A17
D15
D7
D14
D6
D13
D5
D12
D4
D11
D3
D10
D2
D9
D1
D8
D0
RDZ
A1
RAMDB7
MAD10
MAD0
MAD1
MAD2
MAD3
DQM0
(2-A2)
(2-A2) /SDWDE
(2-A2) /SDCAS
(2-A2) /SDRAS
(2-A3) /SDCS
(2-A3) BANK0
(2-A3) BANK1
VCC
DQ0
VCCQ
DQ1
DQ2
VSSQ
DQ3
DQ4
VCCQ
DQ5
DQ6
VSSQ
DQ7
VCC
LDQM
WE
CAS
RAS
CS
BA0
BA1
A10
A0
A1
A2
A3
VCC
VSS
DQ15
VSSQ
DQ14
DQ13
VCCQ
DQ12
DQ11
VSSQ
DQ10
DQ9
VCCQ
DQ8
VSS
NC
UDQM
CLK
CLKE
NC
A11
A9
A8
A7
A6
A5
A4
VSS
54
53
52
51
50
49
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
RAMDB15
RAMDB14
RAMDB13
RAMDB12
RAMDB11
RAMDB10
RAMDB9
RAMDB8
DQM1 (2-A2)
SDCLK (2-A2)
SDCKE (2-A2)
R50
0J
MAD12
MAD11
MAD9
MAD8
MAD7
MAD6
MAD5
MAD4
C399
N.M.
SDRAM (16bit x 4bank)
2
/CS0 (1-A2)
VCC3
C75
0.1u
C76
0.1u
C77
0.1u
C78
0.1u
C79
0.1u
C80
0.1u
C81
0.1u
C82
0.1u
MAD[12..0] (2-A3)
IC6
5
SDRAM
LH28F800BJE-PBTL90
128Mb(2Mx16bitx4bank)
0J
Vendor/Type
MT48LC8M16A2TG-75(Micron)
HY57V281620HCT(Hyndai)
K4S281632E-TC75(Samsung)
W981216BH-75(Winbond)
1
64Mb(1Mx16bitx4bank)
C
HY57V641620HGT-P
Hyndai)
MT48LC4M16A2TG-75
Micron)
K4S641632F-TC75(Samsung)
K4S641632E-TC1H(Samsung)
W986416DH-7(Winbond)
D
FO-DC550 CIRCUIT DIAGRAM 14 - 6
E
A
B
C
MCU PWB (Driver section 1)
Digital Input Multiplexer
5V
(7-E2)
(7-E4)
(7-E3)
(7-E1)
(7-E3)
(7-E4)
(7-E3)
(7-E1)
(PPD1)
(POD)
(MFD)
(CED1)
(TCS)
(PMRDY)
DVS1
(DRST)
4
3
2
1
15
14
13
12
(10-E3)(4-E2)
(10-E3)(4-E2)
(10-E3)(4-E2)
(SELIN1)
(SELIN2)
(SELIN3)
11
10
9
7
4
5V/3.3
IC9
D0
D1
D2
D3
D4
D5
D6
D7
VCC
16
R56
Y
W
A
B
C
G
GND
5
(10-C4) KEYIN
SIN1
SIN2
SIN3
SPFS
SRRC
SGS
SPUS
SIN1 (4-C4)
10J
6
C83
C84
0.1u
33p
8
74HC151
5V
16
VCC3
R57
Y
W
A
B
C
G
GND
5
R55
10kJ
SIN2 (4-C4)
10J
6
C87
C88
0.1u
33p
(2-D2) OP_CLK
(2-D2) OP_DATA
(2-D2) OP_LATCH
PSL
(1-A2)
8
FW
BZR
(1-D3)
/ASIC_RST
R317
74HC151
3
4
3
2
1
15
14
13
12
(SDSW)
(SPID)
(SB4D)
(SDOD)
(PD1)
(PD2)
(7-E4)
(7-E4)
(7-E4)
(11-D3)
(7-E4)
(7-E4)
11
10
9
7
VCC
D0
D1
D2
D3
D4
D5
D6
D7
A
B
C
G
10kJ
5V
5V
IC13
47pF
11
10
9
7
VCC
D0
D1
D2
D3
D4
D5
D6
D7
R59
10kJ
16
C389
4
3
2
1
15
14
13
12
(PPD2)
(PPD3)
THOPEN
(CED2)
DSWS
(MMLD)
(7-E2)
(7-E4)
(5-E2)
(7-E1)
(7-C4)
(7-E3)
IC11
R60
Y
W
GND
5
SIN3 (4-C4)
10J
6
C90
C91
0.1u
33p
8
(4-C3)
MIRCNT
74HC151
(1-A2)
SPFMT0
(1-A2)
SPFMT1
(1-A2) SPFMT2/MIRCNT
(1-A2)
SPFMT3
(2-D1)
MIRON
(2-D1)
SPFON
4
3
2
1
Extension Digital Output Port
BR68
10kJ
(15-C2) (3-A1) (2-A1) (1-D2) D[15..0]
VCC3
VCC3
2
5
0.1u
(1-A2) /CS3
1
IC17
11
1
10
4
2
3
(3-A2) (1-B3) /HWR
2
3
4
5
6
7
8
9
D8
D9
D10
D11
D12
D13
D14
D15
VCC3
C93
NC7S32M5X
5
6
7
8
IC15
VCC
Q1
Q2
Q3
Q4
Q5
Q6
Q7
Q8
D1
D2
D3
D4
D5
D6
D7
D8
20
19
18
17
16
15
14
13
12
CLK
OC
GND
SFTMT0
SFTMT1
SFTMT2
SFTMT3
(6-D3)
(6-D3)
(6-D3)
(6-D3)
(1-B3)
(1-B3)
(1-B3)
(2-D1)
(2-D1)
(2-D1)
(2-D2)
(2-D2)
MCNT
C94
SELIN1
SELIN2
SELIN3
KEYSC1
KEYSC2
KEYSC3
TM
TM_
R344
33J
R346
33J
R3
33
0.1u
74LCX574
VCC3
EN5V
(2-C1)
4
DEVDIR
A
OE
B
GND
5
5V
2
(SDA1)
(1-D3)
(1-D3)
(1-D3)
(1-D3)
(1-D3)
(1-D3)
3
TC7SBD385AFU
C103
0.1u
1
IC20
EN5V
C109
R348
0J
R350
0J
/RESET#
R309
10kJ
5V
1
(1-E2) SCL
LCDDB7
LCDDB6
LCDDB5
LCDDB4
LCDE
LCDRS
/RESET0
R308
10kJ
EN5V
3.3V
3.3V
R347
0J
R349
0J
OPEN
Vcc
1
C394
3.3V
SDA1
OPEN
IC18
C393
R336
10kJ
4
2
(SCL1) (11-D3)
NC7ST08M5X
0.1u
For CRUM Model Only
A
B
FO-DC550 CIRCUIT DIAGRAM 14 - 7
C
C
D
E
4/14
5V
VCC3
5V/3.3V
VCC3
3.3V
R54
10kJ
IC10
2
4
6
8
11
13
15
17
1
19
10
1A1
1A2
1A3
1A4
2A1
2A2
2A3
2A4
1G
2G
GND
VCC
1Y1
1Y2
1Y3
1Y4
2Y1
2Y2
2Y3
2Y4
20
18
16
14
12
9
7
5
3
(KEYIN) (1-A3)
(SIN1)
(SIN2)
(SIN3)
SPFS#
SRRC#
SGS#
SPUS#
IC45
Vcc
1
(11-B2) /SYNC
3
A1
Y1
A2
Y2
5
6
(/SYNC) (2-E1)
4
C379
4
0.1u
C85
GND
47p
2
NC7WZ17
C86
0.1u
74LCX244
3
VCC3
3.3V
2
4
6
8
11
13
15
17
1
19
10
R58
47pF
R315
IC12
1A1
1A2
1A3
1A4
2A1
2A2
2A3
2A4
1G
2G
GND
8
7
6
5
(OP_CLK)
(OP_DATA)
(OP_LATCH)
(PSL)
(10-E3)
(10-E3)
(10-E3)
(10-E4)
(FW)
(BZR)
(10-E3)
(/ASIC_RST)
C89
C388
0.1u
OPEN
5V
10kJ
C389
33J
R342
100J
74LCX244
10kJ
3.3V
BR88
1
2
3
4
20
VCC 18
1Y1 16
1Y2 14
1Y3 12
1Y4 9
2Y1 7
2Y2 5
2Y3 3
2Y4
3
IC107
(2-C1)
VCC3
3.3V
1
VIDEO#
2
4
R61
100J
/VIDEO
(11-A2)
NC7ST08M5X
3.3V
5V
IC14
1A1
1A2
1A3
1A4
2A1
2A2
2A3
2A4
1G
2G
GND
VCC
1Y1
1Y2
1Y3
1Y4
2Y1
2Y2
2Y3
2Y4
20
18
16
14
12
9
7
5
3
C380
0.1u
(SPFMT0)
(SPFMT1)
(SPFMT2)
(SPFMT3)
(6-B1)
(6-B1)
(6-B1)
(6-B1)
4
3
2
1
2
4
6
8
11
13
15
17
1
19
10
C92
0.1u
BR67
10kJ
5
6
7
8
74LCX244
5V
3.3V
2
4
6
8
11
13
15
17
1
19
10
1A1
1A2
1A3
1A4
2A1
2A2
2A3
2A4
1G
2G
GND
VCC
1Y1
1Y2
1Y3
1Y4
2Y1
2Y2
2Y3
2Y4
5V
2
20
18
16
14
12
9
7
5
3
(SELIN1)
(SELIN2)
(SELIN3)
(KEYSC1)
(KEYSC2)
(KEYSC3)
(TM)
(TM_)
(4-A4) (10-E3)
(4-A4) (10-E3)
(4-A4) (10-E3)
(10-E3)
(10-E3)
(10-E3)
(6-D2)
(6-D2)
(LCDDB7)
(LCDDB6)
(LCDDB5)
(LCDDB4)
(LCDE)
(LCDRS)
(10-E3)
(10-E3)
(10-E3)
(10-E3)
(10-E3)
(10-E3)
0.1u
33pF
33pF
33pF
R345
33J
IC16
C95
C392
C391
C390
74VHCT244
VCC3
3.3V
R323
R324
/RESET#
/RESET1
OPEN
1
0.01uF
C104
C396
C395
C394
C393
74LCX244
C
1kJ
33J
C378
1A1
1A2
1A3
1A4
2A1
2A2
2A3
2A4
1G
2G
GND
VCC
1Y1
1Y2
1Y3
1Y4
2Y1
2Y2
2Y3
2Y4
C377
2
4
6
8
11
13
15
17
1
19
10
20
18
16
14
12
9
7
5
3
0.1u
OPEN
OPEN
OPEN
OPEN
IC19
D
FO-DC550 CIRCUIT DIAGRAM 14 - 8
E
A
B
C
MCU PWB (Driver section 2)
24V
4
BR107
1
2
3
4
MC
(2-C1)
(2-C1) BIAS
TC
(2-C1)
(2-C1) GRIDL
MCNT
CPFS2
1.5kJ
8
7
6
5
IC21
1
2
3
4
5
6
7
8
R325
1.5kJ
R343
1.5kJ
1B
2B
3B
4B
5B
6B
7B
E
1C
2C
3C
4C
5C
6C
7C
COM
16
15
14
13
12
11
10
9
/MC
/BIAS
/TC
/GRIDL
/MCNT
(
(
(
(
/CPFS2
KID65001AF
PGND
24V
(2-D1)
(2-D1)
(2-C1)
BR108
1
2
3
4
CPFS1
MPFS
RRS
1
2
3
4
VFM
(2-C1)
(2-C1) VFMCNT
PR
(2-D1)
3
BR109
1.5kJ
8
7
6
5
1
2
3
4
5
6
7
8
8
7
6
5
1.5kJ
IC23
1B
2B
3B
4B
5B
6B
7B
E
1C
2C
3C
4C
5C
6C
7C
COM
16
15
14
13
12
11
10
9
/CPFS
/MPFS
/RRS
/VFMC
/PR
KID65001AF
PGND
24V
IC25
3
4
5
6
10
11
12
13
14
15
SPFS#
SPUS#
SGS#
SRRC#
I1
NC
NC
I2
NC
I3
NC
NC
I4
NC
17
18 GND
GND
O1
O2
O3
O4
COM
COM
2
/SPFS (11-E1)
7
/SPUS (11-E1)
9
/SGS
16
/SRRC (11-E1)
(11-E1)
(1-A2)
(2-C1)
(2-D1)
(2-D1)
(2-C1)
(2-D1)
(5-E3)
1
8
PMCLK
MRPS1
MRPS2
MRPS3
LDEN
HL
FTH
1
2
3
4
5
6
7
8
IC26
1B
2B
3B
4B
5B
6B
7B
G
1C
2C
3C
4C
5C
6C
7C
NC
16
15
14
13
12
11
10
9
PMCLK_
MRPS_1
MRPS_2
MRPS_3
/LDEN
KID65503F
TD62064AF
PGND
2
For SPF/DSPF Model Only
(2-C1)
(2-A3)
(2-A3)
(2-C1)
(1-D3)
(2-C1)
(2-C1)
MMD
MM_Y1
MM_Y2
MM_Y3
POFF
PMD
/LEND
1
2
3
4
5
6
7
8
IC27
1B
2B
3B
4B
5B
6B
7B
G
1C
2C
3C
4C
5C
6C
7C
NC
16
15
14
13
12
11
10
9
/MMD (
MMref0 (
MMref1 (
MMref2 (
/POFF (
/PMD (
KID65503F
1
A
B
FO-DC550 CIRCUIT DIAGRAM 14 - 9
C
C
D
E
5/14
C
AS
C
RIDL
CNT
4
(10-B4)
(10-A4)
(10-B4)
(10-A4)
PFS2
VCC3
R67
1MF
R68
7.5kF
8
R66
1kF
12V
1
2 R71
4.3kF
FTH (5-B2)
12V
4
MA700
R69
1kJ
IC22A
KIA393F
3 +
D1
R70
10kF
VCC3
C110
0.1u
24V
R73
/CPFS1
/MPFS
/RRS
(11-B3)
VCC3
47kJ
R78
/VFMCNT (11-A3)
4.7kJ
(10-A3)
/PR
1/4W
VCC3
D3
D2
Q1
KTA1505S
3
VFMOUT
1
12V
8
1SS355
3 +
(11-C1) RTH_IN
C111
22000p
R81
300J
3
R82
100J
1
2 -
PGND
2
KDS226
IC24A
KIA358F
RTH (1-A3)
C112
12V
4
D40
3
2
KDS226
(11-A3)
1
0.1u
C113
0.1u
INT5V
VCC3
12V
5V
D4
1SS355
R83
1.2kF
8
1
Q2
KRA119S
(11-B2)
(6-A1)
(6-A1)
(6-A1)
(11-B2)
5 +
2
R86
240J
R85
10kF
R87
240J
R84
10kJ
7
6 -
3
4
MCLK_A
RPS_1
RPS_2
RPS_3
DEN
IC22B
KIA393F
THOPEN (4-A4)
C114
22000p
HLOUT (10-B3)
2
8
12V
IC24B
KIA358F
5 +
7
4
6 -
5V
R88
10kJ Q3
KRC106S
3
SHOLD (11-B2)
2
1
MD (11-A4)
Mref0 (6-A3)
Mref1 (6-A3)
Mref2 (6-A3)
OFF (10-B4)
MD (11-B2)
1
C
D
FO-DC550 CIRCUIT DIAGRAM 14 - 10
E
A
B
C
MCU PWB (Driver section 3)
4
Scanner Motor Driver
(10-D2) OUT_A(10-D2) OUT_A+
(10-D2) OUT_B+
(10-D2) OUT_B-
24VM
5V
R89
R90
0.68J
1W
PGND
1
2
3
4
5
6
7
8
9
10
11
12
C116
820p
MM_BI0
(2-A3)
MM_BI1
(2-A3)
(2-A3) MM_PH_B
5V
R93
1kJ
C117
820p
R96
2kJ
3
R97
1kJ
R98
510J
R91
1.5kJ
IC29
R92
1.5kJ
C119
0.1u
24
OUT 1A
VS 23
OUT 2A SENSE 1 22
SENSE 2 COMP 1 21
OUT 1B 20
COMP 2
I01 19
OUT 2B
GND 18
GND
GND 17
GND
I11 16
I02
I12
PHASE 1 15
PHASE 2
VREF 1 14
VREF 2
RC 1 13
RC 2
VSS
MM_AI0
5V
PGND
C115
820p
(2-A3)
PGND
MM_AI1 (2-A3)
MM_PH_A (2-A3)
L6219DS or AMM56219
R94
30kJ
0.68J
1W
R95
30kJ
C118
820p
PGND
PGND
PGND
C121
0.1u
(5-C1) MMref0
(5-C1) MMref1
(5-C1) MMref2
CP2
0603FA1.5A
24VM
PGND
C123
0.1u/50V
PGND
0.
SPF Motor Driver
C125 2200p
R99
7.5kJ
R100 7.5kJ
C126 2200p
2
C127 OPEN
PGND
5V
R101
1kJ
R102
750J
R103 1J 2W
C130
IC31
23
20
25
3
24
19
12
18
C132
R107
300J
R108
620J
R109
1.2kJ
R110
100J
C134
0.1u
(5-C2)
(5-C2)
(5-C2)
MRPS_1
MRPS_2
MRPS_3
24VM
OPEN
R104 2.4kJ
2200p
R111 2.4kJ
C135
26
27
17
16
2200p
PGND
R114 1J 2W
PGND
PGND
R115
1kJ
C136
OPEN
In /A
In A
In /B
In B
Vmm
OUT /A
OUT A
OUT /B
OUT B
22
1
4
14
11
SPMT_2
SPMT_0
SPMT_3
SPMT_1
(11-E
(11-D
(11-D
(11-E
15
PG 28
PG
MTD1361/F
PGND
C137 OPEN
(4-D3)
(4-D3)
(4-D3)
(4-D3)
CrA
CrB
VsA
RsA
VrefA
VrefB
RsB
VsB
(SPFMT2)
(SPFMT0)
(SPFMT3)
(SPFMT1)
1
A
B
FO-DC550 CIRCUIT DIAGRAM 14 - 11
C
C
D
E
6/14
Duplex Motor Driver
3
4
5
6
10
11
12
13
14
15
(1-D3) DMT0
(1-D3) DMT1
(1-D3) DMT2
(1-D3) DMT3
17
18
4
IC28
O1
I1
NC
NC
I2
NC
I3
NC
NC
I4
NC
GND
GND
O2
2
/DMT0 (11-B3)
7
/DMT1 (11-B3)
9
O3
/DMT2 (11-B3)
16
O4
/DMT3 (11-B3)
24VDup
COM
COM
D5
1
8
TD62064AF
MTZ J22B
PGND
Shifter Motor Driver
24V
CP1
0603FA1.5A
24VSFT
(4-B2) SFTMT1
CP3
0603FA1.5A
5A
24VDup
V
C124
0.1u/50V
+
C122
47u/35V
(4-B2) SFTMT0
(4-B2) SFTMT2
(4-B2) SFTMT3
3
4
5
6
10
11
12
13
14
15
R338
0J
R339
0J
R340
0J
R341
0J
17
18
IC30
I1
NC
NC
I2
NC
I3
NC
NC
I4
NC
GND
GND
2
O1
7
O2
9
O3
16
O4
/SFTMT0 (11-A1)
/SFTMT1 (11-A1)
/SFTMT3 (11-A1)
24VSFT
D6
1
8
COM
COM
TD62064AF
PGND
3
/SFTMT2 (11-A1)
MTZ J22B
PGND
Toner Motor Driver
24V
2
C128
10u/35V
_2
_0
_3
_1
(11-E1)
(11-D1)
(11-D1)
(11-E1)
R105
1kJ
(4-D3) (TM)
(4-D3) (TM_)
R112
47kJ
R106
1kJ
R113
47kJ
PGND
IC32
19
20
18
21
1
2
3
4
7
10
11
12
13
Vcc
PSAVE VM
OUT1
Rin
OUT2
Fin
VREF
RNF
NC
GND
FIN
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
+
C129
0.1u/50V
PGND
17
16
9
5
TMB_O (11-A1)
TMA_O (11-A1)
6
8
FIN
25
24
23
22
15
14
BA6920FP
PGND
1
C
D
FO-DC550 CIRCUIT DIAGRAM 14 - 12
E
A
B
C
MCU PWB (Noise filter/Pull-up section)
4
VCC3
5V
C138
C139
C140
C141
C142
C143
C144
C145
C146
0.1u
OPEN
0.1u
0.1u
OPEN
OPEN
OPEN
OPEN
OPEN
D11
1
3
2
KDS226
C147
C148
C149
C150
C151
C152
C153
C154
C155
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
C156
C157
C158
C159
C160
C161
C162
C163
C164
OPEN
OPEN
OPEN
OPEN
0.1u
0.1u
OPEN
OPEN
OPEN
C174
C175
C176
C177
C178
C179
C180
C181
C182
0.1u
0.1u
0.1u
0.1u
0.1u
0.1u
0.1u
0.1u
OPEN
R132
20kJ
D12
1SS355
DSWS (4-A3)
R134
2.7kJ
R133
20kJ
C165
0.1u
INT24V
R135
24V1(DSWS) (9-A3)
0.22J 2W
PGND
24V
C183
+
47u/35V
PGND
D20
1SS355
INT24V
C184
R145
100J 2W
0.1u/50V
IC33
1
PGND
C189
+
IN
OUT
2
3
D17
1SS355
3
KIA7805
47u/35V
2
L5
ZJSR5101-223
INT5V
GND
R136
1kJ
2W
C190
0.1u
L6
ZJSR5101-223
(10-A4) 12VIN
12V
C191
+
47u/25V
(10-B4) 3.3VIN
C193
VCC3
C192
0.1u
+
C194
0.1u
22u/16V
5V
C195
22u/16V
+
EN5V
C197
C196
0.1u
22u/16V
+
C198
0.1u
1
A
B
FO-DC550 CIRCUIT DIAGRAM 14 - 13
C
C
D
E
7/14
5V
D7
1
D8
3
2
1
KDS226
D9
D10
1
3
2
KDS226
1
3
2
KDS226
4
3
2
R116
10kJ
R117
10kJ
R118
10kJ
R119
4.7kJ
R120
10kJ
R121
10kJ
R122
39kJ
R123
10kJ
KDS226
(11-D1) SDSW
(11-E1) SPID
(11-E1) SB4D
(11-D2) PPD3
PD1
(11-B1)
PD2
(11-D2)
(11-C2) POD
(11-A2)PMRDY
R124
R125
R126
R127
R128
R129
1kJ
1kJ
1kJ
1kJ
1kJ
1kJ
R130
R131
1kJ
1kJ
(SDSW)
(SPID)
(SB4D)
(PPD3)
(PD1)
(PD2)
(4-A3)
(11-E1)
(4-A3)
(4-A4)
(4-A3)
(4-A3)
(4-A4)
(POD)
(PMRDY) (4-A4)
5V
D14
1
D16
D15
3
2
1
KDS226
1
3
2
D13
1
3
2
KDS226
KDS226
3
2
C166
C167
C168
C169
C170
C171
C172
C173
1000p
1000p
1000p
1000p
1000p
1000p
1000p
1000p
KDS226
3
5V
D18
1
D19
3
2
1
3
2
KDS226
R137
10kJ
R138
10kJ
R139
39kJ
R140
10kJ
KDS226
R141
R142
R143
R144
(11-C3) DVSEL
(11-C3)
TCS
(11-C1) MFD
(11-A4) MMLD
1kJ
1kJ
1kJ
1kJ
DVS1
(TCS)
(MFD)
(MMLD)
(4-A4)
(4-A4)
(4-A4)
(4-A3)
5V
D21
1
D22
3
2
1
2
KDS226
C185
C186
C187
C188
1000p
1000p
1000p
1000p
3
KDS226
2
5V
VCC3
D23
1
D24
3
2
1
KDS226
D25
3
2
KDS226
1
2
3
KDS226
1
R146
39kJ
R147
39kJ
R148
7.5kJ
R149
7.5kJ
R150
7.5kJ
D26
3
2
R151
10kJ
R152
3.3kJ
KDS226
(11-C2) PPD1
(11-C1) PPD2
(11-D1) SPPD
(10-E4) PSW
(11-B4) CED1
(11-D2) CED2
(10-E4) DRST
5V
R153
R154
R155
R156
1kJ
1kJ
1kJ
1kJ
R157
R158
R159
1kJ
1kJ
1kJ
(PPD1)
(PPD2)
(SPPD)
(PSW)
(4-A4)
(4-A4)
(1-D2)
(1-D2)
(CED1) (4-A4)
(CED2) (4-A3)
(DRST) (4-A4)
VCC3
D27
1
2
D28
3
KDS226
1
2
3
C199
C200
C201
C202
1000p
1000p
1000p
1000p
1
2
KDS226
D29
3
C203
C204
1000p
1000p
KDS226
1
C
D
FO-DC550 CIRCUIT DIAGRAM 14 - 14
E
A
B
C
MCU PWB (IMC2 section 1/2)
IC37
(2-D3)
(2-D4)
119
120
124
125
126
127
128
129
131
132
133
134
135
137
138
141
142
/PIWR
(2-D3) /PIACK
(2-D3) /PIREQ
PIDATA[7..0]
PIDATA7
PIDATA6
PIDATA5
PIDATA4
PIDATA3
PIDATA2
PIDATA1
PIDATA0
4
OA_RX
OA_TX
RY_BY
168
169
170
(8-C1) CLK_EXT
(13-C3) PB_NCS1
BR74 1
2
3
4
BR75 1
2
3
4
(9-B3) (9-B3) (13-C4) PB_DATA[7:0]
8 33JX4
7
6
5
8 33JX4
7
6
5
PB_DATA7
PB_DATA6
PB_DATA5
PB_DATA4
PB_DATA3
PB_DATA2
PB_DATA1
PB_DATA0
3
(9-A2) PB_NCS3
(9-A2) (13-C3) PB_NAE0
(9-B3) (13-C4)
(9-B2) (13-C3) PB_NWE
(9-B2) (13-C3) PB_NOE
BR77
PB_ADDR0
PB_ADDR1
PB_ADDR2
PB_ADDR3
BR78
PB_ADDR4
PB_ADDR5
PB_ADDR6
PB_ADDR7
PB_ADDR[7:0]
(1-B3)
(1-B3)
8 33JX4
7
6
5
8 33JX4
7
6
5
1
2
3
4
1
2
3
4
MODEM_IN
USBVBUS
2
C267
NC
/FPOFF
R320
10kJ
(2-E3)
(9-B2)
(2-E3)
/SC_LINE
INT_USBD
/PR_LINE
/FPOFF
(2-D4)
/H_SYNC
(2-D3)
(2-D3)
/POREQ
/POACK
/FPOFF
1
2
3
4
BR36 1
2
3
4
BR38
PODATA7
PODATA6
PODATA5
PODATA4
PODATA3
PODATA2
PODATA1
PODATA0
10KJ
(2-E3)
24
26
28
29
30
31
32
34
(2-D2) /IMC_READY
(13-C3)
MDM_IRQ
(9-D3)
SUSPEND
R232
199
201
202
203
204
205
207
208
15
16
19
21
22
23
/ES_PAGE
/ESC_RDY
/ESS_RDY
WAKEUP
R231
7.5kF
178
180
181
182
183
185
186
187
188
189
190
194
195
196
197
198
1
2
8
9
11
12
13
14
ES_CMD
ESS_TS
(1-D2)
(FW)
(9-B2) DT_ACKB
(9-B2) DT_REQB
(1-A3)
(1-B3)
(1-B3)
(9-D3)
143
145
146
147
151
152
153
154
155
156
157
159
160
161
162
163
165
166
167
8
7
6
5
8 33J
7
6
5
33J
PODATA[7..0]
37
38
39
40
42
43
44
45
47
48
49
50
51
52
175
176
PI_LINE_SYNC/GP_D6
PI_TR_TGEN
PI_TGEN6
PI_TGEN5
PI_TGEN4
PI_TGEN3
PI_TGEN2
PI_TGEN1
PI_TGEN0
PI_DATA7
PI_DATA6
PI_DATA5
PI_DATA4
PI_DATA3
PI_DATA2
PI_DATA1
PI_DATA0
SDRAM_DATA0
SDRAM_DATA1
SDRAM_DATA2
SDRAM_DATA3
SDRAM_DATA4
SDRAM_DATA5
SDRAM_DATA6
SDRAM_DATA7
SDRAM_DATA8
SDRAM_DATA9
SDRAM_DATA10
SDRAM_DATA11
SDRAM_DATA12
SDRAM_DATA13
SDRAM_DATA14
SDRAM_DATA15
PP_HIDRIVE/USART1_RX
PP_DRIVE/USART1_TX
PP_NINIT
PP_NFAULT
PP_NSELECTIN
PP_NAUTOFD
PP_SELECT
PP_PERROR
PP_BUSY
PP_NACK
PP_DATA7
PP_DATA6
PP_DATA5
PP_DATA4
PP_DATA3
PP_DATA2
PP_DATA1/USART1_CK
PP_DATA0
PP_NSTROBE
BASE_CLK/GP_PWM1
CLK_EXT/GP_PWM2
MAIN_CLK/GP_PWM0
REG_A9/PB_NCS1
REG_A8/PB_NCS2
REG_AD7/PB_DATA7
REG_AD6/PB_DATA6
REG_AD5/PB_DATA5
REG_AD4/PB_DATA4
REG_AD3/PB_DATA3
REG_AD2/PB_DATA2
REG_AD1/PB_DATA1
REG_AD0/PB_DATA0
REG_ADDR_VALID/PB_NCS0
REG_RD_L/PB_NCS3
REG_WR_L/PB_NAE0
REG_CS_L/PB_NAE1
REG_RDY/PB_NWE
INTERRUPT_L/PB_NOE
GP_C0/PB_ADDR0
GP_C1/PB_ADDR1
GP_C2/PB_ADDR2
GP_C3/PB_ADDR3
GP_C4/PB_ADDR4
GP_C5/PB_ADDR5
GP_C6/PB_ADDR6
GP_C7/PB_ADDR7
10KJ
TDO
10KJ
TCK
10KJ
TMS
10KJ
TDI
10KJ TRST_L
(1-B1) (2-C1) (9-B2)
/OA_RST
R233
R234
TDO
TCK
TMS
TDI
TRST_L
OPEN
OPEN
R235
R236
4.7KJ
4.7KJ
VCC3
1
C300
15P
X4
32.3022MHz
R237
TDO
TCK
TMS
TDI
TRST_L
112
113
114
116
117
118
172
177
5
4
0J
XIN
XOUT
SDRAM_WE_L
SDRAM_CAS_L
SDRAM_RAS_L
SDRAM_ADDR0
SDRAM_ADDR1
SDRAM_ADDR2
SDRAM_ADDR3
SDRAM_ADDR4
SDRAM_ADDR5
SDRAM_ADDR6
SDRAM_ADDR7
SDRAM_ADDR8
SDRAM_ADDR9
SDRAM_ADDR10
SDRAM_ADDR11
SDRAM_ADDR12
SDRAM_BANK0
SDRAM_BANK1
SDRAM_CLK
SDRAM_CKE
SDRAM_DATA0
SDRAM_DATA1
SDRAM_DATA2
SDRAM_DATA3
SDRAM_DATA4
SDRAM_DATA5
SDRAM_DATA6
SDRAM_DATA7
SDRAM_DATA8
SDRAM_DATA9
SDRAM_DATA10
SDRAM_DATA11
SDRAM_DATA12
SDRAM_DATA13
SDRAM_DATA14
SDRAM_DATA15
BR69 1
2
3
4
BR70 1
2
3
4
BR71 1
2
3
4
BR72 1
2
3
4
8
7
6
5
8
7
6
5
8
7
6
5
8
7
6
5
109
107
106
105
SDRAM_DQMA0
SDRAM_DQMB0
SDRAM_DQMA1
SDRAM_DQMB1
BR73 1
2
3
4
8 33JX4
7
6
5
_SDRAM_DQMA
_SDRAM_DQMB
_SDRAM_DQMA
_SDRAM_DQMB
104
102
77
75
SDRAM_CS0_L
R218
33J
_SDRAM_CS0_
R332
33J
R333
R334
R335
33J
33J
33J
111
110
101
BR111 1
2
3
4
BR112 1
2
3
4
BR113 1
2
3
4
BR114 1
2
3
4
100
99
97
96
95
94
92
91
90
89
85
82
80
84
83
79
78
8
7
6
5
8
7
6
5
8
7
6
5
8
7
6
5
R356
150JX4 _SDRAM_DATA
_SDRAM_DATA1
_SDRAM_DATA2
_SDRAM_DATA3
150JX4 _SDRAM_DATA4
_SDRAM_DATA5
_SDRAM_DATA6
_SDRAM_DATA7
150JX4 _SDRAM_DATA8
_SDRAM_DATA9
_SDRAM_DATA1
_SDRAM_DATA1
150JX4 _SDRAM_DATA1
_SDRAM_DATA1
_SDRAM_DATA1
_SDRAM_DATA1
PLLSS_VSSA
S
SDR
SDR
33JX4 SDRAM_ADDR0
SDRAM_ADDR1
SDRAM_ADDR2
SDRAM_ADDR3
33JX4 SDRAM_ADDR4
SDRAM_ADDR5
SDRAM_ADDR6
SDRAM_ADDR7
33JX4 SDRAM_ADDR8
SDRAM_ADDR9
SDRAM_ADDR10
SDRAM_ADDR11
33JX4 SDRAM_ADDR12
SDRAM_BANK0
SDRAM_BANK1
33J
R225
R226
SDRAM_CKE
OA3.3V
PLLCS_VDDA
PLLSS_VDDA
GP_B0/USART0_TX
GP_B1/USART0_RX
GP_B2/USART0_CK
GP_B3/ANA_SD1
GP_B4/DT_ACKB
GP_B5/DT_REQB
GP_B6/DT_ACKA
GP_B7/DT_REQA
C400
N.M.
7
C259
0.01U
C260
1U
C262
0.01U
C263
1U
6
149
148
OA3.3V
GP_D0/ADC_A0
GP_D1/ADC_A1
GP_D2/ADC_A2
GP_D3/ADC_CLK
GP_D4/ADC_DATA
GP_D5/ADC_NCS
GP_A0
GP_A1
GP_A2/DC_CHY1
GP_A3/DC_CHX1
GP_A4/DC_PWM1
GP_A5/DC_CHY0
GP_A6/DC_CHX0
GP_A7/DC_PWM0
PO_LINE_SYNC/ANA_SCLK
PO_PAGE_SYNC/ANA_NCS
PO_REQ/ANA_SD0
PO_ACK/PDATA0/PDS0
PO_DONE/PDATA2/PDS2
PO_WR/PDATA1/PDS1
PO_DATA7/LHEAT/PAS_M
PO_DATA6/LCTRL/CFIRE2
PO_DATA5/AGATE/CFIRE1
PO_DATA4/ACLK/MFIRE2
PO_DATA3/PENABLE/MFIRE1
PO_DATA2/PLOAD
PO_DATA1/PCLK
PO_DATA0/PDATA3/PAS_C
USB_DM
USB_DP
RESET_L
TDO
TCK
TMS
TDI
TRST_L
TEST_MODE0
TEST_MODE1
VDD_IO
VDD_IO
VDD_IO
VDD_IO
VDD_IO
VDD_IO
VDD_IO
VDD_IO
VDD_IO
VDD_IO
VDD_IO
VDD_IO
VDD_IO
VDD_IO
VDD_IO
VDD_IO
VDD_IO
XIN
XOUT
3
20
25
33
46
59
71
81
93
103
115
130
144
158
171
184
200
OA3.3V
VDD_CORE
VDD_CORE
VDD_CORE
VDD_CORE
VDD_CORE
VDD_CORE
VDD_CORE
VDD_CORE
VSS_IO
VSS_IO
VSS_IO
VSS_IO
VSS_IO
VSS_IO
VSS_IO
VSS_IO
VSS_IO
VSS_IO
VSS_IO
VSS_IO
VSS_IO
VSS_IO
VSS_IO
VSS_IO
VSS_CORE
VSS_CORE
VSS_CORE
VSS_CORE
VSS_CORE
VSS_CORE
VSS_CORE
VSS_CORE
18
36
70
88
122
140
174
192
10
27
41
54
64
76
86
98
108
123
136
150
164
179
193
206
C273
0.1U
C274
0.1U
C275
0.1U
C276
0.1U
C277
0.1U
C278
0.1U
C283
0.1U
C284
0.1U
C285
0.1U
C286
0.1U
C287
0.1U
C288
0.1U
C292
0.1U
C293
0.1U
C294
0.1U
C295
0.1U
C296
0.1U
C297
0.1U
17
35
69
87
121
139
173
191
OA-982
(8-A3) CLK_EXT
C306
15P
A
SDRAM_CS0_L
SDRAM_CS1A_L
SDRAM_CS1B_L
ROM_CS_L
PLLCS_VSSA
VCC3
R244
R243
R242
R241
R240
SDRAM_DQMA0
SDRAM_DQMB0
SDRAM_DQMA1
SDRAM_DQMB1
74
73
72
68
67
66
65
63
62
61
60
58
57
56
55
53
B
FO-DC550 CIRCUIT DIAGRAM 14 - 15
CLK_EXT
C
C
D
E
8/14
_SDRAM_DATA[15:0] (8-D4) (8-E4) (8-E3)
M_DATA0
_DATA1
_DATA2
_DATA3
_DATA4
_DATA5
_DATA6
_DATA7
_DATA8
_DATA9
_DATA10
_DATA11
_DATA12
_DATA13
_DATA14
_DATA15
(8-C3) (8-D3) (8-D2) (8-E4) SDRAM_ADDR[12:0]
(8-C3) (8-D2)
_DQMA0
_DQMB0
_DQMA1
_DQMB1
(8-C4) (8-E4) (8-E3)
_SDRAM_DATA[15:0]
M_CS0_L
ROM_CS_L
SDRAM_WE_L
SDRAM_CAS_L
SDRAM_RAS_L
SDRAM_ADDR[12:0] (8-E4) (8-D3) (8-D4)
_SDRAM_DATA[15:0] (8-C4) (8-D4) (8-E3)
IC38
SDRAM_ADDR1
SDRAM_ADDR2
SDRAM_ADDR3
SDRAM_ADDR4
SDRAM_ADDR5
SDRAM_ADDR6
SDRAM_ADDR7
SDRAM_ADDR8
SDRAM_ADDR9
SDRAM_ADDR10
SDRAM_ADDR11
SDRAM_ADDR12
SDRAM_BANK[1:0]
SDRAM_BANK0
SDRAM_BANK1
SDRAM_WE_L
SDRAM_CAS_L
SDRAM_RAS_L
_SDRAM_DQMB0
_SDRAM_DQMB1 R330
0J
VCC3
_SDRAM_DATA8 R327
0J
_SDRAM_DATA9 R328
0J
25
24
23
22
21
20
19
18
8
7
6
5
4
3
2
1
48
17
16
9
10
R329
_SDRAM_DQMA1
_SDRAM_DQMA0
ROM_CS_L
11
28
26
10kJ
RY_BY
15
47
14
12
/RESET0
IO0
IO1
IO2
IO3
IO4
IO5
IO6
IO7
IO8
IO9
IO10
IO11
IO12
IO13
IO14
IO15/A-1
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
A16
A17
A18
A19
A20
_SDRAM_DATA0
_SDRAM_DATA1
_SDRAM_DATA2
_SDRAM_DATA3
_SDRAM_DATA4
_SDRAM_DATA5
_SDRAM_DATA6
_SDRAM_DATA7
29
31
33
35
38
40
42
44
30
32
34
36
39
41
43
45
4
SDRAM_ADDR[12:0]
(8-C3) (8-D3) (8-D4)
VCC3
R217
SDRAM_ADDR0
0J
VCCW
WE
OE
CE
13
VCC3
VCC
C256
NM
37
RY/BY
C257
0.1U
BYTE
WP/ACC
RESET
GND
GND
46
27
Flash ROM
Flash ROM
Model
SDRAM_BANK[1:0] (8-D4) (8-D2) (8-D1)
_SDRAM_CLK
_SDRAM_CKE
33J
4.7KJ
5
6
_SDRAM_CLK
(8-D2)
Vendor/Type
E-Sort Model
4Mbit
LH28F400BVE-BL85
R327/R328/R330 ; OPEN
FAX Model
(US)
8Mbit
LH28F800BJE-PBTL90
R327/R328/R330 ; OPEN
FAX Model
(except US)
16Mbit
LH28F160BJE-BTL90
R327/R328/R330 ; 0J
3
IC39
(8-C3) (8-E4) (8-D4)
(8-C3) (8-D4)
SDRAM_ADDR[12:0]
SDRAM_BANK[1:0]
(8-C3) _SDRAM_CLK
OA3.3V
VCC3
L10
ZJSR5101-102TA
C278
0.1U
C279
0.1U
C280
0.1U
C281
0.1U
+
SDRAM_ADDR0
SDRAM_ADDR1
SDRAM_ADDR2
SDRAM_ADDR3
SDRAM_ADDR4
SDRAM_ADDR5
SDRAM_ADDR6
SDRAM_ADDR7
SDRAM_ADDR8
SDRAM_ADDR9
SDRAM_ADDR10
SDRAM_ADDR11
SDRAM_ADDR12
SDRAM_BANK0
SDRAM_BANK1
23
24
25
26
29
30
31
32
33
34
22
35
36
20
21
_SDRAM_CS0_L
SDRAM_WE_L
SDRAM_CAS_L
SDRAM_RAS_L
19
16
17
18
_SDRAM_CLK
_SDRAM_CKE
38
37
_SDRAM_DQMA0
_SDRAM_DQMA1
15
39
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
BA0
BA1
DQ0
DQ1
DQ2
DQ3
DQ4
DQ5
DQ6
DQ7
DQ8
DQ9
DQ10
DQ11
DQ12
DQ13
DQ14
DQ15
CS
WE
CAS
RAS
_SDRAM_DATA[15:0] (8-C4) (8-D4) (8-E4)
_SDRAM_DATA0
_SDRAM_DATA1
_SDRAM_DATA2
_SDRAM_DATA3
_SDRAM_DATA4
_SDRAM_DATA5
_SDRAM_DATA6
_SDRAM_DATA7
_SDRAM_DATA8
_SDRAM_DATA9
_SDRAM_DATA10
_SDRAM_DATA11
_SDRAM_DATA12
_SDRAM_DATA13
_SDRAM_DATA14
_SDRAM_DATA15
VCC3
VDDQ
VDDQ
VDDQ
VDDQ
CLK
CKE
LDQM
UDQM
C401
N.M.
VDD
VDD
VDD
VSSQ
VSSQ
VSSQ
VSSQ
C272
47U/16V
40
2
4
5
7
8
10
11
13
42
44
45
47
48
50
51
53
VSS
VSS
VSS
N.C
49
43
9
3
27
14
1
52
46
12
6
54
41
28
VCC3
C268
0.1U
C269
0.1U
C270
0.1U
C271
0.1U
C332
0.1U
C333
0.1U
C334
0.1U
2
K4S561632D
C288
0.1U
C289
0.1U
C290
0.1U
VCC3
C297
0.1U
C298
0.1U
_SDRAM_DATA0
_SDRAM_DATA1
_SDRAM_DATA2
_SDRAM_DATA3
_SDRAM_DATA4
_SDRAM_DATA5
_SDRAM_DATA6
_SDRAM_DATA7
_SDRAM_DATA8
_SDRAM_DATA9
_SDRAM_DATA10
_SDRAM_DATA11
_SDRAM_DATA12
_SDRAM_DATA13
_SDRAM_DATA14
_SDRAM_DATA15
C299
0.1U
BR115 1
2
3
4
BR116 1
2
3
4
BR117 1
2
3
4
BR118 1
2
3
4
8
7
6
5
8
7
6
5
8
7
6
5
8
7
6
5
10kJX4
_SDRAM_CS0_L
10kJX4
_SDRAM_CKE
C264
NM
C265
47p
10kJX4
10kJX4
1
T
R238
4.7KJ
C
D
FO-DC550 CIRCUIT DIAGRAM 14 - 16
E
A
B
C
MCU PWB (IMC2 USB2.0 section 2/2)
4
VCC3
C314
0.01U
C315
0.01U
C316
0.01U
C317
0.01U
C318
0.01U
C319
0.01U
VCC3
VCC3
GND
C320
C323
0.1U
C324
0.1U
C325
0.1U
C326
0.1U
C327
0.1U
C328
0.1U
+
10U/16V
GND
VCC3
(9-B3) (13-C4) PB_ADDR[7:0]
C338
0.1U
GND
C339
0.1U
PB_ADDR0
PB_ADDR1
PB_ADDR2
PB_ADDR3
PB_ADDR4
PB_ADDR5
PB_ADDR6
PB_ADDR7
VCC3
IC42
(8-A3)
PB_NCS3
(8-A3) (13-C3)
PB_NAE0
40
41
44
45
46
47
48
49
50
51
52
53
54
55
56
57
10
(2-D1) /OA_RST
1
4
2
NC7S08M5X
GND
2
PB_DATA0
PB_DATA1
PB_DATA2
PB_DATA3
PB_DATA4
PB_DATA5
PB_DATA6
PB_DATA7
(8-A2)
(8-A2)
(8-A2)
(13-C3) (8-A3)
(13-C3) (8-A3)
INT_USBD
DT_REQB
DT_ACKB
PB_NOE
PB_NWE
25
28
12
13
26
27
PB_NOE
PB_NWE
11
29
VCC3
IC43
2
R303
100P
1
VCC(3.3) 24
VCC(3.3) 58
/
/
INT
RE
DATA0
DATA1
DATA2
DATA3
DATA4
DATA5
DATA6
DATA7
DATA8
DATA9
DATA10
DATA11
DATA12
DATA13
DATA14
DATA15
WAK
SUSP
XT
XT
Vreg(
/RESET
/CS
INT
DREQ
DACK
/RD
/WR
EOT
ALE
ISP1581
4
D
D
MO
MO
BUS_C
AGND
DGND
(8-A3) (9-B3) (13-C4) PB_DATA[7:0]
AD0
AD1
AD2
AD3
AD4
AD5
AD6
AD7
R
3
23
30
31
32
33
34
35
38
39
DGND
DGND
DGND
DGND
PB_DATA0
PB_DATA1
PB_DATA2
PB_DATA3
PB_DATA4
PB_DATA5
PB_DATA6
PB_DATA7
VCC(5.0)
VCC(5.0)
VCC(5.0)
VCC(5.0)
IC41
(8-A3) (9-B3) (13-C4) PB_DATA[7:0]
1
36
42
61
3
2
37
43
64
GND
R304
0J
NC7S04M5X
R305 NM
GND
GND
GND
L12
GND
1
A
B
FO-DC550 CIRCUIT DIAGRAM 14 - 17
AG
AGND
MLF1608-J
AG
GND
C
C
D
E
9/14
4
C321
0.1U
+ C322
10U/16V
10KJ
10KJ
10KJ
NC
10KJ
R281
R282
R284
R287
AG
R280
VCC3
GND
17
18
16
22
21
62
63
/CS1
/CS0
INTRQ
READY
DA2
WAKEUP
SUSPEND
3
PB_NOE
PB_NWE
14
15
20
9
19
DIOR
DIOW
MODE0
MODE1
BUS_CONF
R283
R285
10KJ
10KJ
R286
R288
10KJ
NC
WAKEUP (8-A2)
SUSPEND (8-A2)
R289
10KJ
C329
60
XTAL1
Y1
C330
4
Vreg(3.3)
10P
GND
12MHz
59
XTAL2
R293
1.5KJ
R290
10KJ
GND
GND
(8-A2) USBVBUS
L14
10P
BLM21PG600SN1
GND
CN33
1 +5V
2 -D
3 +D
4 GND
5 SHIELD
7
RPU
5
6
DD+
L15 DLW21SN900SQ2
8
RREF
2
UBR23(ACON)
R301 NM
USB2.0 DEV1
R302
12KF
C331 0.01U
L16
BLM21PG600SN1
FG
AG AGND_UD2
FGND_UD2
AGND_UD2
L13
GND
C
MLF1608-J
FG
FGND_UD1
1
D
FO-DC550 CIRCUIT DIAGRAM 14 - 18
E
A
B
C
MCU PWB (Connector section 1)
To Power unit
4
INT5V
INT24V
CN1
C208
1
3
5
7
9
11
13
15
17
19
21
23
2
4
6
8
10
12
14
16
18
20
22
24
2
4
6
8
10
12
14
16
18
20
22
24
/TC
/MC
(5-C4)
(5-C4)
3.3VIN
(7-B2)
/POFF
24V
(5-C1)
(7-A2)
HLOUT
(5-D2)
B24B-PHDSS-B
0.1u/50V
2
C207
0.1u/50V
1
EN5V
5V
12VIN
FW
/PR
1
(7-A2)
(4-C4)
(5-C3)
/BIAS
/GRIDL
2
(5-C4)
(5-C4)
1
3
5
7
9
11
13
15
17
19
21
23
PGND
PGND
3
2
1
A
B
FO-DC550 CIRCUIT DIAGRAM 14 - 19
C
C
D
E
10/14
To Operational PWB
4
EN5V
5V
VCC3
5V
CN2
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
D30
1
1
R160
10kJ
3
2
KDS226
DRST
PSW
2
1000p
1
C211
2
2
1000p
1000p
1
(PSL)
(OP_CLK)
(OP_LATCH)
(OP_DATA)
(SELIN1)
(SELIN2)
(SELIN3)
(LCDDB7)
(LCDDB6)
(LCDDB5)
(LCDDB4)
(LCDE)
(LCDRS)
(BZR)
(KEYSC1)
(KEYSC2)
(KEYSC3)
C210
2
C205
1000p
1
KEYIN
1kJ
2
C209
2
(4-C4)
1
1
R162
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
28FE-BT-VK-N
3
To Mirror motor
2
CN4
(6-A4)
(6-A4)
(6-A4)
(6-A4)
OUT_A+
OUT_B+
OUT_AOUT_B-
1
1
2
2
3
3
4
4
B4B-PH-K-R
1
C
D
FO-DC550 CIRCUIT DIAGRAM 14 - 20
E
A
B
MCU PWB (Connector section 3)
4
To Mech. COUNTER
24V
CN8
3
2
1
/MCNT
B3B-PH-K-S
3
To Cover open detect
5V
5V
D37
3
1
2
KDS226
R177
4.7kJ
R178
1kJ
R318
150J
1/4W
CN14
3
2
1
(4-A3) (SDOD)
C221
1000p
B3B-PH-K-S
(White)
For SPF/DSPF Model Only
2
A
B
FO-DC550 CIRCUIT DIAGRAM 14 - 21
C
D
11/14
To 2nd. cassette
4
24V 5V
1000p
1000p
PD2
CED2
C228
PPD3
(7-C4)
(7-C1)
C227
(7-C4)
1000p
/CPFS2
C226
CN18
(5-C3)
1
3
5
7
9
11
13
2
4
6
8
10
12
14
B14B-PHDSS-B
PGND
3
2
C
D
FO-DC550 CIRCUIT DIAGRAM 14 - 22
FO-DC550 CIRCUIT DIAGRAM 14 - 23
1
2
3
4
/ACK
BUSY
PE
SLCT
/FAULT
(2-D2)
/REV
/OA_RST
(2-D2)
/STB
(2-D2) /AUTOFD
(2-D2) /SLCTIN
(2-D2)
/INIT
(2-D2)
(2-D2)
(2-D2)
(2-D2)
(2-D2)
(2-E2) PARAD[7..0]
VCC3 EN5V
A
R319
0J
PARAD0
PARAD1
PARAD2
PARAD3
PARAD4
PARAD5
PARAD6
PARAD7
/ACK
BUSY
PE
SLCT
/FAULT
/STB
/AUTOFD
/SLCTIN
/INIT
R326
/REV
OPEN
/REV
CN39
10kJ
To NIC PWB
24FMN-BTK-A
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0.1u
B
C243
0.1u
VCC3
10kJ
C242
R198
10
15
1
48
19
24
20
21
22
23
/STB
/AUTOFD
/SLCTIN
/INIT
17
16
14
13
12
11
9
8
7
18
GND
GND
PLH
HLHin
C14
C15
C16
C17
Y9
Y10
Y11
Y12
Y13
B8
B7
B6
B5
B4
B3
B2
B1
Vcc-cable
Vcc-cable
74LVX161284
GND
GND
HD
DIR
PLHin
HLH
A14
A15
A16
A17
A9
A10
A11
A12
A13
A8
A7
A6
A5
A4
A3
A2
A1
Vcc
Vcc
IC34
IEEE1284 Driver/Receiver
2
3
4
5
6
R197
3.3V
B
/ACK
BUSY
PE
SLCT
/FAULT
PARAD0
PARAD1
PARAD2
PARAD3
PARAD4
PARAD5
PARAD6
PARAD7
VCC3
MCU PWB (IEEE1284Interface section)
A
34
39
30
25
29
28
27
26
47
46
45
44
43
32
33
35
36
37
38
40
41
31
42
0.1u
EN5V
10kJ
0.1u
C245
EN5V
C244
R200
5V
C
C
100p 330p 100p 100p
C246 C247 C248 C249
100p 100p 100p 100p 100p
C237 C238 C239 C240 C241
100p 100p 100p 100p 100p 100p 100p 100p
C229 C230 C231 C232 C233 C234 C235 C236
R209
BR92
1
2
3
4
R204
BR91
1
2
3
4
1
2
3
4
BR90 1
2
3
4
BR89
8
7
6
5
8
7
6
5
10kJ
22J
22J
22J
22J
8
7
6
5
8 22J
7
6
5
D
D
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
F.G
/D STB
Data 0
Data 1
Data 2
Data 3
Data 4
Data 5
Data 6
Data 7
/ACK
BUSY
PE
SLCT
/AUTO FD
NC
SG
FG
PLHOUT
CN28
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
IEEE1284_CN
D-GND
D-GND
D-GND
D-GND
D-GND
D-GND
D-GND
D-GND
D-GND
D-GND
D-GND
D-GND
/INIT
/FAULT
D-GND
NC
HLHIN
/SLCT IN
IEEE1284 Connector
Shield
E
R196
E
3.3KJ
11EQS06
D39
EN5V
12/14
1
2
3
4
1
2
3
A
(4-A3) MODEM_IN
(1-B3) (2-C1) (3-A2)
/RD
(1-D3)
/CS4
MSU_ST1
(1-A3)
(2-D1)
(9-B2) (8-A3)
2
1
NC7S32M5X
4
IC46
MDM_IRQ
B
(1-D2) (2-A1) (3-A1) (4-A2) D[15..0]
MSU_ST1
R306
10kJ
VCC3
/FWREN
PB_NWE
VCC3
R357 N.M.
(8-A2)
PB_NOE
/OA_RST
MDM_IRQ
(2-D1)
PB_NCS1
PB_NAE0
(9-B2) (8-A3)
PB_ADDR[7:0]
(8-A3)
(9-A2) (8-A3)
(8-A3) (9-B3)
(8-A3) (9-B3) (9-B3) PB_DATA[7:0]
D7
D6
D5
D4
D3
D2
D1
D0
C402
PGND
24V EN5V VCC3
0.1u
VCC3
PB_ADDR7
PB_ADDR6
PB_ADDR5
PB_ADDR4
PB_ADDR3
PB_ADDR2
PB_ADDR1
PB_ADDR0
PB_DATA7
PB_DATA6
PB_DATA5
PB_DATA4
PB_DATA3
PB_DATA2
PB_DATA1
PB_DATA0
20FE-BT-VK-N
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
CN38
26FE-BT-VK-N
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
CN37
C
To Modem PWB
To Modem PWB
D7
D6
D5
D4
D3
D2
D1
D0
MSU_ST1
PB_DATA7
PB_DATA6
PB_DATA5
PB_DATA4
PB_DATA3
PB_DATA2
PB_DATA1
PB_DATA0
MDM_IRQ
C368
OPEN
4
5
3
C359
OPEN
C360
OPEN
C361
OPEN
MCU PWB (Modem I/F Connector)
C
D
D
C372
OPEN
B
C364
OPEN
C365
OPEN
C375
OPEN
A
C367
OPEN
C376
OPEN
C362
OPEN
C363
OPEN
C371
OPEN
C369
OPEN
C370
OPEN
C366
OPEN
C374
OPEN
C373
OPEN
FO-DC550 CIRCUIT DIAGRAM 14 - 24
E
13/14
E
1
2
3
4
FO-DC550 CIRCUIT DIAGRAM 14 - 25
1
2
3
4
(2-A4) CL
A
R169
15kJ
C216 33p
R170
56kJ
C213
47u/35V
+
24V
R166
10kJ
B
PGND
Q5
KTC3198
R168
5.6kJ
1/4W
Q4
KTB1151 Y
D33
11EQS06
B
TWKA-221K
L9
220uH
Copy Lamp Inverter
MCU PWB (Scanner I/F section)
A
47u/35V
+ C214
0.1u/50V
C215
R167
15kJ
CP4
0603FA1.5A
VCL
C
(1-D2) mt_at_home
C
R165
1kJ
1000p
C212
R164
10kJ
VCC3
2
1
3
KDS226
D32
(2-A4)
(2-A4)
(2-A4)
(2-A4)
(2-A4)
(1-D2) (2-A4)
D
AFE_DB[7..0]
AFE_SCK
ADCLK
CCD_PHI1
CCD_PHI2
CCD_CP
CCD_RS
CCD_TG
D
VCL
AFE_DB0
AFE_DB2
AFE_DB4
AFE_DB6
PGND
12V
31
29
27
25
23
21
19
17
15
13
11
9
7
5
3
1
AFE_DB0
AFE_DB1
AFE_DB2
AFE_DB3
AFE_DB4
AFE_DB5
AFE_DB6
AFE_DB7
FF4-32-S15D5
32
30
28
26
24
22
20
18
16
14
12
10
8
6
4
2
CN3
To Scanner unit
PGND
EN5V
E
VCL
VSAMP
AFE_SDI
BSAMP
AFE_SEN
AFE_DB5
AFE_DB7
AFE_DB1
AFE_DB3
14/14
E
1
2
3
4
FO-DC550 CIRCUIT DIAGRAM 14 - 26
1
2
3
OP-LATCH
OP-DATA
OP-CLK
A
Open
C308
1
2
KRC106S
Q302
R324
0J
1
3
2
3
R323
10KJ
3.3V
R325
0J
1
Q304
KRA225S
3
Q303
KRA225S
R303
3
B
R326
0J
Q305
KRA225S
2
1
4
5V
R304
100J
R302
0.1u
C322
3.3V
100J
100J
6
5
LED305
2CAS
1CAS
ALM
SPON
LED306
LED307
SCAN
FAX
LED308
LED302
LED301
COPY
LED304
C
/OUT0
16
VCC
7
/OUT1
1000p 1000p open
C305 C306 C307
2
S-IN
8
/OUT2
4
CLOCK
3
2
OPERATION PWB (LED/LCD Section)
9
/OUT3
/LATCH
10
/OUT4
13
/ENABLE
11
/OUT5
R305
0J
R327
820J
R306
OPEN
14
S-OUT
12
/OUT6
15
/OUT7
GND
R-EXT
TB62725AF
IC304
READY
LED310
MB
LED309
PRINT
LED303
C
=(1.15/820)x14.9=20.9mA
Iout=(1.15/Rext)x14.9 [A]
open
C323
1
B
DATA1
LED_V3
LCDDB[7..4]
LED_V2
LED_V1
LCDDB4
LCDDB5
LCDDB6
LCDDB7
D
PSL
LCDE
D
R333
2
LCDRS
KRC106S
Q301
100J
R328
10kJ
R332
R331
R330
R329
R334
1
LCDE#
LCDDB4#
LCDDB5#
LCDDB6#
LCDDB7#
LCDRS#
3
LCDDB7#
LCDDB6#
LCDDB5#
LCDDB4#
LCDE#
LCDRS#
100J
100J
100J
100J
100J
560J
R335
3.3V
R301
470J
1/3
Pin Holes x 10
GPM181C0
GND
V5
VDD
RS
R/W
E
DB4
DB5
DB6
DB7
IC301
PML
E
LED311
0.1u
E
To LCD
10
9
8
7
6
5
4
3
2
1
C333
5VEN
C332
100p
C327
100p
C328
100p
C329
100p
C330
100p
C331
100p
A
1
2
3
4
2. OPERATION PWB
FO-DC550 CIRCUIT DIAGRAM 14 - 27
1
2
3
4
2
KRC106S
47pF
C315
A
Open Open Open
C311 C310 C309
KEYIN
Open Open Open
C318 C319 C320
SELIN3
SELIN2
SELIN1
KEYSC1
KEYSC2
KEYSC3
BZR
Q306
R317
R316
R315
R318
R338
R337
R336
3
0.1u
PSW
5V
0.1u
C312
C321
1kJ
1kJ
1kJ
33J
1kJ
1kJ
1kJ
R339
2
5V
10kJ
PS1720P02
1
BZ301
5
6
6
4
5
1
2
3
Y0
Y1
Y2
Y3
Y4
Y5
Y6
Y7
Open
C304
74HC151
Y
W
IC302
A
B
C
G
D0
D1
D2
D3
D4
D5
D6
D7
74HC238
G1
G2A
G2B
A
B
C
IC303
5VEN
11
10
9
7
4
3
2
1
15
14
13
12
15
14
13
12
11
10
9
7
PSW
KEY310
OPERATION PWB (KEY / Buzzer Section)
A
1
B
B
R314
R313
R312
R311
R307
R308
R309
R310
100J
100J
100J
100J
100J
100J
100J
100J
1SS133
D303
1SS133
D302
1SS133
D301
R342
2kJ
C337
C335
Open
Open
C
2kJ
R341
F-KEYIN1
NM5K
NM3K
F-KEYSC1
F-KEYSC2
F-KEYSC3
KEY319
NM2K
CLK
KEY324
KEY323
NM6K
KEY320
KEY325
CAK
KEY321
C
Open
C334
2kJ
R340
F-KEYIN2
NM9K
KEY317
NM4K
KEY318
NM1K
KEY322
Open
C313
2kJ
R319
F-KEYIN3
NM0K
KEY308
SHPK
KEY309
NM8K
KEY316
Open
C314
2kJ
R320
F-KEYIN4
ASTK
KEY307
NM7K
KEY315
MAGK
KEY306
D
D
Open
C316
2kJ
R321
F-KEYIN5
EXMODK
KEY305
UPK
KEY313
ENTK
KEY314
Open
C317
2kJ
R322
F-KEYIN6
ESTK
KEY304
MENUK
KEY311
DWK
KEY312
Open
C336
2kJ
R343
F-KEYIN7
DUPK
KEY303
CASK
KEY302
MODK
KEY301
E
E
F-KEYIN8
2/3
1
2
3
4
FO-DC550 CIRCUIT DIAGRAM 14 - 28
LCDE
LCDRS
BZR
KEYSC1
KEYSC2
KEYSC3
B
LCDDB[7..4]
0.1u
C325
47uF/16v
C301
0.1u
C326
Close to CN1
C
18FE-ST-VK-N
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
CN301
To FAX Key PWB
F-KEYIN7
F-KEYIN6
F-KEYIN5
F-KEYIN4
F-KEYIN3
F-KEYIN2
F-KEYIN1
F-KEYIN8
F-KEYSC3
F-KEYSC2
F-KEYSC1
LED_V3
LED_V2
LED_V1
DATA1
D
DRST
S3B-PH-K-S
1
2
3
CN303
To Drum Initial Detector
E
E
3/3
3
4
1
LCDDB7
LCDDB6
LCDDB5
LCDDB4
PSW
KEYIN
PSL
OP-CLK
OP-LATCH
OP-DATA
SELIN1
SELIN2
SELIN3
47uF/16v
C302
5VEN
D
1
A
0.1u
47uF/16v
DRST
C324
C303
5V
C
2
28FE-ST-VK-N
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
CN302
3.3V
To MCU PWB
B
2
3
4
OPERATION PWB (Connector Section)
A
3. POWER SUPPLY
1
2
3
4
5
6
3
4
5
6
POWER SUPPLY (120V/127V)
A
B
C
D
E
F
G
H
1
2
FO-DC550 CIRCUIT DIAGRAM 14 - 29
6
7
8
9
10
11
12
1/1
A
B
C
D
E
F
G
H
6
7
8
9
FO-DC550 CIRCUIT DIAGRAM 14 - 30
10
11
12
1
2
3
L1
L2
L3
BT1
LT1
TEL1
TEL2
LT2
BT2
MJ2
SBT-0260
L4
SBT-0260
1
2
3
4
5
6
A
MJ-62J-RD315/MJ-66J-RD315
MJ-62J-RD315/MJ-66J-RD315
1
2
3
4
5
6
MJ1
SA3
DSS-401M
H1
SBT-0260
L5
SBT-0260
L6
Q1001
2SC4548(E)
C1005
B0.01u/50V
R1013
120K
B
R1117
N.M.
R11
100kF(1608)
R1023
0R(N.M.)
R1022
0R(N.M.)
5.36kF 1/4W
R1019
Q1000
2SA1759
E
C
FL4
ST110AV
Q2
2SD1733
3
1
FB1
BLM31A601S
R1017
150(1608)
L1
TWKA-221KNP
DAAGND
B
Secondary side
FB3
BLM31A601S
R1018
2.2K 1/10W
RY1A
OUAZ-SH-124DZ
L2
TWKA-221KNP
C6
1000p/AC250V(NM)
C7
1000p/AC250V(NM)
4
1
2
3
C1006
B0.1u/50V
402F(1608)
C26
R29
91 1/4W
0.47uF/250V
R1003
C13
B1uF/16V
78.7F(1608)
Q1
2SC4548(E)
C
E
9.31kF(1608)
3
2
R1002
10k 1W
R27
R1021
56k 1/10W
4
1
R1020
56k 1/10W
S1ZB60
D3
1.78kF 2W(N.M.)
R12
Si3015-FS
FILT2
FILT
RX
REXT
REXT2
REF
VREG2
VREG
QE2
DCT
IGND
C1B
RNG1
RNG2
QB
QE
5.36KF 1/4W
R1016
IC1
5.36KF 1/4W
R1015
ZD2
MTZJ30B
C1011
B560p/250V
C
ZD3
HZS2A1
ZD4
HZS2A1
1
2
3
4
5
6
7
8
AK
R30
30 1/4W
DSS401M(N,M.)
VA1
C1009
B560p/250V
D4
1SS355
16
15
14
13
12
11
10
9
5.36KF 1/4W
R1014
D2
DAN217
4
B1800p/50V
C1004
B
C
E
K
A
B
5.36kF 1/4W
R1028
DSS-401M
1.78kF 2W(N.M.)
R28
B0.1u/16V
C1002
PC1A
PC2A
PC814X
TLP621
PC2B
PC814X
PC1B
TLP621
GND
C27
B1000p/50V
GND
C25
B1000p/50V
(2125)
C12
B0.022u/250V
R4
10 1/10W
C3
EXHKD_L
CID_L
150p/AC250V
C10
C11
(3216) N.M.
DAAGND
AK
Secondary side
150p/AC250V
Primary side
D
10 1/10W
R3
C2
10pF/50V
D
K
D1
DAN217
A
C14
B0.22u/16V
B0.1u/16V
C1001
RLZ5.6
ZD1
FAX MAIN PWB (TEL/LIU)
SA2
SA1
5.36kF 1/4W
R1027
DSS-401M
ZD1001
RD43FM
C4
2200pF(KH)
C5
2200pF(KH)
10M
R13
215F(1608)
R5
R14
10M
R1001
B0.68u/16V
C1003
C15
B0.01u/250V(N.M.)
RLZ5.6
ZD1000
DAAGND
R1
DAA3.3V
4
1SS355
+3.3V
DAAGND
OUAZ-SH-124DZ
+-
RY1B
D1000
5
1
2
3
4
5
6
7
8
C9
B0.1u/16V
R1029
0R (1608)
+24V
Si3021-FS
OFHK
MCLK
RGDT/FSD FSYNC
M0
SCLK
VA
VD
GND
SDO
C1A
SDI
M1
FC/RGDT
AOUT
RESET
IC2
GND
0R(N.M.)
0R(N.M.)
16
15
14
13
12
11
10
9
R10
0R
DAA3.3V
DAAGND
TPGND
DAA3.3V
B0.22u/10V
C1
C
1
2
C1007
B3900p/16V
C1008
B3900p/16V
AFERST_L
ARXD
ATXD
MCLOCK
ASPCLK
ABITCLK
R7
0R
C
PG
E
Q3
DTC123JKA
B
DAAGND
GND
R45
10K
DAA3.3V
DAAGND
R1000
10K
1/6
FB2
MEM2012(N.M.)
3
SPOUT
C1000
1000pF
1
E
RGDT-
2
B
2
1
4
3
4
3
FO-DC550 CIRCUIT DIAGRAM 14 - 31
E
A
S
1
2
3
4
4. FAX MAIN PWB
FO-DC550 CIRCUIT DIAGRAM 14 - 32
A
B
C
D
VOL_C
VOL_B
VOL_A
VOLCNT_B
VOLCNT_A
BZ
SPOUT
R1032
20k
4
4700pF
C1023
AG
R1031
1.6k
AG
R1042
10K
+5V
2200pF
C1022
R1035
3.3K
R1038
1K
R1040
10K
C1025
F0.1u/16V
C1024
F0.1u/16V
Vref
56k
56k
56k
56k
AG
R1039
R1033
R1034
R1037
FAX MAIN PWB (SPEAKER)
6
11
10
9
13
14
15
12
1
5
2
4
IC4
+5V
X
VEE
VSS
VDD
BU4051BCF
INH
A
B
C
X0
X1
X2
X3
X4
X5
X6
X7
10k
7
8
16
3
GND
GND
0R
0R
R1059
R1060
AG
+5V
3
AG
C35
F0.1u/16V
C1026
F0.1u/16V
3
Vref
1M
R1041
4
10k
F0.1u/16V(N.M.)
R42
10k
C1027
R43
F0.1u/16V(N.M.)
C1029
R44
F0.1u/16V(N.M.)
C1030
R1047
R1045
R1049
R1043
R1048
R1044
R1046
5.1k
10k
18K
33K
62K
100K
200K
AG
6
11
10
9
13
14
15
12
1
5
2
4
IC6
X
VEE
VSS
VDD
BU4051BCF
INH
A
B
C
X0
X1
X2
X3
X4
X5
X6
X7
7
8
16
3
AG
+5V
C37
F0.1u/16V
3.3K
SPMUTE
R1050
AG
R1058
1k
+5V
C1028
F0.1u/16V
2
AG
Vref
R1055
3.3k
C42
A4.7u/50V
R1052
22k
0R
+5V
R1053
R1051
10K(N.M.)
HZS2C1
ZD5
Vref
2
100k
C28
A4.7u/50V
A4.7u/50V
C39
R1054
4
2
3
200K
C40
A4.7u/50V
R1056
C1031
100pF
+5V
6
AG
1
7
8
IC7
NJM2113M
5
0R
1
C41
10uF(N.M.)
R1057
1
SP
OUT
1
2
CN4
B2B-PH-K-S
2/6
A
B
C
D
A
B
C
D
R46
560
R47
360
ZD6
UDZ2.0B
A[21:0]
GND
+3.3V
TR2
KTC3875
R49
1k
TR3
KTA1504
+3.3V
4
R48
1k
R50
20k
GND
R51
1k
TR1
KTA1504
+3.3V
GND
C45
F0.1u/16V
BAT
1
D1001
1SS355
CS_S1L
BT1
CR2477(3V)
R57
1k
GND
2
D[7:0]
R58
100k
2
1
OEL
WEL
NC
GND
PST3426
VCC
OUT
IC12
CS_S0L
CS_S1L
FAX MAIN PWB (SRAM & FLASHROM(16M))
4
GND
GND
30
6
32
5
10
7
11
4
12
1
31
2
3
13
14
15
16
17
18
19
20
0R
R59
TR4
DTC363EKA
C
B
3
4
A16
A15
A14
A13
A12
A11
A10
A9
A8
A7
A6
A5
A4
A3
A2
A1
A0
E
FO-DC550 CIRCUIT DIAGRAM 14 - 33
3
24
8
9
29
28
27
26
25
23
22
21
C_BT
L_BT-
VSS
VCC
NC
I/O7
I/O6
I/O5
I/O4
I/O3
I/O2
I/O1
I/O0
IS62WV1288BLL
CE1
CE2
OE
WE
A16
A15
A14
A13
A12
A11
A10
A9
A8
A7
A6
A5
A4
A3
A2
A1
A0
IC10
3
A17
BAT
GND
C47
F0.1u/16V
D7
D6
D5
D4
D3
D2
D1
D0
+
C46
22uF/16V
F_WP
CS_FL
RESETL
GND
R1030
75
C1032
100pF
A21
A20
A19
A18
A17
A16
A15
A14
A13
A12
A11
A10
A9
A8
A7
A6
A5
A4
A3
A2
A1
A0
26
12
28
11
14
10
9
16
17
48
1
2
3
4
5
6
7
8
18
19
20
21
22
23
24
25
GND
GND
VPP
VCC
RY/BY
BYTE
DQ15
DQ14
DQ13
DQ12
DQ11
DQ10
DQ9
DQ8
DQ7
DQ6
DQ5
DQ4
DQ3
DQ2
DQ1
DQ0
2
RTC_CE0H
RTC_CLK
RTC_DATA
MBM29LV160BE90TN
CE
RP
OE
WE
WP
NC
A19
A18
A17
A16
A15
A14
A13
A12
A11
A10
A9
A8
A7
A6
A5
A4
A3
A2
A1
A0
IC9
2
27
46
13
37
15
47
45
43
41
39
36
34
32
30
44
42
40
38
35
33
31
29
D7
D6
D5
D4
D3
D2
D1
D0
GND
R56
10k
R55
10k
+3.3V
GND
C48
F0.1u/16V
+3.3V
F_RYBY
1
5
6
7
IC11
SM8578BV
I/O-
CE
CLK
DATA
VSS
XT
XT-
VDD
4
2
3
8
GND
BAT
JP3
C54
F0.1u/16V
1
2
1
0R
12pF(N.M.)
C51
4
3
12pF
C53
1
18pF(N.M.)
C50
X2
MC-306/DT-38 32.768KHz
12pF
C52
3/6
A
B
C
D
A
B
C
D
MDM_IRQ
+3.3V
MDM3.3V
D[7:0]
7
R33
R34
R35
R36
R37
R38
R39
R40
A[21:0]
C1018
100pF
D7 1
D6 2
D5 3
D4 4
D3
D2
D1
D0
47K
47K
47K
47K
47K
47K
47K
47K
GND
MDM3.3V
CS_ML
OEL
WEL
M_RESETL
0R
R21
GND
4.7k
R25
BR1
R17
R18
8 33
7
6
5 BR2
1
2
3
4
A11
A10
A9
A8
A7
A6
A5
A4
A3
A2
A1
A0
47K
47K
8 33
7
6
5
GND
25
24
22
20
19
18
16
14
13
12
10
8
7
6
4
2
100
98
96
95
94
93
91
90
88
87
85
84
41
75
74
73
71
72
1
FAX MAIN PWB (MN195006Q)
7
DPD15
DPD14
DPD13
DPD12
DPD11
DPD10
DPD09
DPD08
DPD07
DPD06
DPD05
DPD04
DPD03
DPD02
DPD01
DPD00
DPA11
DPA10
DPA09
DPA08
DPA07
DPA06
DPA05
DPA04
DPA03
DPA02
DPA01
DPA00
NRESET
NDPCS
NDPRD
NDPWR
NUB
NLB
T3IRQ
IC3
C20
F0.1u/16V
C21
F0.1u/16V
C34
F0.1u/16V
C33
F0.1u/16V
C18
F0.1u/16V
C19
F0.1u/16V
C22
F0.1u/16V
C23
F0.1u/16V
C24
F0.1u/16V
C17
F0.1u/16V
C8
A22u/16V
6
+1.8V
MDM3.3V
MN195006E
34
AVDD
6
GND
AVSS
GPIO0
GPIO1
GPIO2
GPIO3
GPIO4
GPIO5
BBITCLK
BSPCLK
BTXD
BRXD
ABITCLK
ASPCLK
ATXD
ARXD
EYECLK
EYEDAT
SCANNT
MINTEST
INTEST
MODE0
MODE1
CXIN
CXOUT
CLKOUT
CNT
LON
NDBGREQ
DBGMOD
PLLON
TMS
TCK
TDI
TDO
C1014
F0.1u/16V
C1013
F0.1u/16V
C16
A22u/16
C1021
F0.1u/16V
C1020
F0.1u/16V
C1017
F0.1u/16V
C1015
F0.1u/16V
C1016
F0.1u/16V
C1019
F0.1u/16V
76
77
79
81
82
83
65
66
69
67
59
60
63
61
57
58
45
46
48
49
50
39
38
43
37
51
R19
47K
5
75
GND
0R
R15
R16
33
+3.3V
4
2
GND
GND
4
C31
C470/16V
4
A2-6PA-2.54DSA(NM)
1
2
3
4
5
6
CN1
VDD
X1
SCO10-24.576000MHz-3.3V
3 OUT
OE 1
CLKIN
GND
MCLOCK
33
AFERST_L
MDM3.3V
MDM3.3V
47K
47K
47K
47K(NM)
47K
47K
R20
47k
47k
47k
47k
R1009
R1010
R1012
R1011
R23
R24
R26
R22
R1025
R1026
0R
R1007
R1006
R1024
47K
MDM3.3V
MDM3.3V
GND
GND
GND
26
27
36
33
31
29
28
5
R8
47K
+3.3V
R1008
47K
GND
+3.3V
R41
0R(N.M.)
R1005
47K
FL10
ZJSR5101(22000p)
R1004
47K
C32
F0.1u/16V
+5V
+3.3V
3
D5
IN
IC5
3
R2
R6
R9
100
100
100
C38
F0.1u/16V(N.M.)
3
0R(3216)
GND
4
ABITCLK
ASPCLK
ATXD
ARXD
OUT2
LM1117-3.3V(N.M.)
OUT1 2
1SS355(N.M.)
R1063
GND
1
FL6
92
78
68
44
30
15
3
VDD3
VDD3
VDD3
VDD3
VDD3
VDD3
VDD3
FL2
FL1
55
54
VDDREG
VDDREG
35
53
52
REGOUT
REGOUT
FL8
FL9
FL3
FL5
FL7
FL11
FL12
97
86
62
42
21
9
VDD2
VDD2
VDD2
VDD2
VDD2
VDD2
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
99
89
80
70
64
56
47
40
32
23
17
11
5
FO-DC550 CIRCUIT DIAGRAM 14 - 34
C1034
F0.1u/16V
R1036
0R(3216 N.M.)
C36
GND
2
A47u/25V
2
MDM3.3V
GND
1
C49
A47u/25V
+3.3V
4/6
1
A
B
C
D
FO-DC550 CIRCUIT DIAGRAM 14 - 35
A
B
C
D
+3.3V
7
1
2
3
4
1
2
3
4
1
2
3
4
R62
R61
1
2
3
4
1
2
3
4
1
2
3
4
8
GND
VOL_C
VOL_B
VOL_A
VOLCNT_B
VOLCNT_A
10K(N.M.)
10K(N.M.)
10K(N.M.)
10K(N.M.)
10K(N.M.)
R1101
R1100
R1099
R1098
R1097
CID_L
EXHKD_L
10K(N.M.) SPMUTE
10K
M_RESETL
22K
RESETL
10k
10k
10K
10K
10K(N.M.)
10K(N.M.)
10K
10K
10K
10K
10K(N.M.)
10K
10K
R1103
R71
R72
R1107
R1084
R1075
R1062
R1068
R1070
R1067
R1072
R1079
R1108
R1102
R1109
R1110
MCU_D7
MCU_D6
MCU_D5
MCU_D4
MCU_D3
MCU_D2
MCU_D1
MCU_D0
MCU_INT
MCU_CEL
MCU_OEL
WEL
OEL
CS_OP2L
CS_OP1L
CS_FL
CS_ML
CS_S0L
F_RYBY
M_RESETL
HS2L
HS1L
8
7 BR5
6 MNR04 (N.M.)
5
22K(N.M.) RESETL
22K(N.M.) WAKE_UP
8
7 BR6
6 MNR04 (N.M.)
5
R1065 22K
R1081 22K
R1086 22K
1
2
3
4
R1076
R1080
8
7 BR22
6 MNR04 22K
5
PB_D7
PB_D6
PB_D5
PB_D4
PB_D3
8
PB_D2
7 BR23
PB_D1
6 MNR04 22K
PB_D0
5
PB_A7
1
8
PB_A6
2
7 BR24
MNR04
iN.M.)
PB_A5
3
6
PB_A4
4
5
PB_A3
8
PB_A2
7 BR25
PB_A1
6 MNR04 iN.M.)
PB_A0
5
R1082 22K
PB_CS1L
R1088 22K
PB_AE0L
R1083 22K
PB_WEL
R1089 22K
PB_OEL
D7
8
D6
7 BR27
D5
6 MNR04 10K
D4
5
D3
1
8
D2
2
7 BR26
3
6 MNR04 10K D1
D0
4
5
10K
A21
A20
10K
A19
1
8
A18
2
7 BR7
3
6 MNR04 10K A17
A16
4
5
A15
8
A14
7 BR8
A13
6 MNR04 10K
A12
5
A11
1
8
A10
2
7 BR9
3
6 MNR04 10K A9
A8
4
5
A7
8
A6
7 BR10
A5
6 MNR04 10K
A4
5
A3
1
8
A2
2
7 BR11
3
6 MNR04 10K A1
A0
4
5
1
2
3
4
7
GND
C29
F0.1u/16V
T2B-SQ
JP2
R31
CLKIN
GND
C30
270pF
1
2
3
4
R1106
R1115
R1114
1
2
3
4
R1087
+3.3V
510
DA204U
D6
GND
FAX MAIN PWB (ASIC_NEW_CILF)
8
RGDT-
1
2
3
4
GND
VDD
S0
FSOUT
VSS
FL23
FL24
6
8
7
6
5
(N.M.)
+3.3V
(N.M.)
C44
F0.1u/16V
R52
5
R68
R67
R66
10k
100
100
100
HS1L
HS2L
WAKE_UP
PB_A7
PB_A6
PB_A5
PB_A4
PB_A3
PB_A2
PB_A1
PB_A0
R1104
GND
R1096
75
D7
D6
F_WP
C1049
100pF
0R
S
BZ
10K
10K
SPMUTE
R1111
R1112
R1113
F_RYBY
CID_L
EXHKD_L
10K
PB_CS1L
PB_AE0L
5
PB_WEL
PB_OEL
RESETL
VOL_C
VOL_B
VOL_A
VOLCNT_B
VOLCNT_A
M_RESETL
GND
C73
F0.1u/16V
(N.M.)
GND
C64
F0.1u/16V
GND
C71
F0.1u/16V
GND
C72
F0.1u/16V
(N.M.)
FL25
FL21
GND
+3.3V
+3.3V
10K
P2782A-08SR
Xin
Xout
S1
LF
IC8
+3.3V
+3.3V
R1105
C_BT
L_BT-
8
7 BR29
6 MNR14 10K
5
10K
10K
10K
8
7 BR30
6 MNR14 10K
5
10K
6
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
GND
GND
TMS
NC
TDI
TDO
FGPIO_03
FGPIO_02
FGPIO_01
FGPIO_00
TELELIN
BEEP_O_V1
BEEP_O_V2
FGPO_15
FGPO_14
FGPO_13
FGPO_12
GND
FGPO_11
FGPO_10
FGPO_09
FGPO_08
GND
VDD
FGPO_07
FGPO_06
FGPO_05
FGPO_04
FGPO_03
FGPO_02
FGPO_01
FGPO_00
FAX_DATA_07
FAX_DATA_06
VDD
GND
XIN
XOUT
GND
GND
VDD
PB_DAT_05
PB_DAT_04
PB_DAT_03
PB_DAT_02
PB_DAT_01
PB_DAT_00
TESTMODE0
PB_ADDR_07
PB_ADDR_06
PB_ADDR_05
PB_ADDR_04
PB_ADDR_03
PB_ADDR_02
PB_ADDR_01
PB_ADDR_00
PB_CE2_N
PB_CE1_N
PB_AE0_N
VDD
GND
PB_WR_N
PB_OE_N
RESET_N
WAKE_UP
FGPI_07
FGPI_06
FGPI_05
FGPI_04
FGPI_03
FGPI_02
FGPI_01
FGPI_00
FGPIO_07
FGPIO_06
FGPIO_05
FGPIO_04
TCK
TRST
VDD
IC13
4
uPD65944GM-P07-JED-A
4
VDD
FAXADD_20
FAXADD_19
FAXADD_18
FAXADD_17
FAXADD_16
FAXADD_15
FAXADD_14
GND
FAXADD_13
FAXADD_12
FAXADD_11
FAXADD_10
FAXADD_09
FAXADD_08
FAXADD_07
FAXADD_06
FAXADD_05
FAXADD_04
GND
VDD
FAXADD_03
FAXADD_02
FAXADD_01
FAXADD_00
FAX_DATA_00
FAX_DATA_01
FAX_DATA_02
FAX_DATA_03
FAX_DATA_04
FAX_DATA_05
TMD0_OUT
TOUT
TESTB
TMD2
TMD1
TMD0
SYSCLK_IN
CLKSEL
VDD
GND
GND
PB_DAT_06
PB_DAT_07
CPU_INT_N
CPU_CS_N
CPU_RD_N
VDD
GND
CPU_DT_00
CPU_DT_01
CPU_DT_02
CPU_DT_03
GND
CPU_DT_04
CPU_DT_05
CPU_DT_06
CPU_DT_07
VDD
GND
FAXWRIN_N
UART_RTS
UART_CTS
UART_SOUT
UART_SIN
RTC_ION
RTC_CE
RTC_SCLK
RTC_SDATA
FAXCS_N_00
FAXCS_N_01
FAXCS_N_02
FAXCS_N_03
FAXCS_N_04
FAXCS_N_05
FAXOE_N
FAXWR_N
FAXADD_21
GND
GND
10K
10K
10K
10K
WEL
+3.3V
0R
A21
8 MCU_D4
7 MCU_D5
6 MCU_D6
5 MCU_D7
CS_OP1L
CS_OP2L
R53
CS_FL
RTC_CE0H
RTC_CLK
RTC_DATA
CS_S0L
R1073
R1077
R1074
R1078
BR3
MCU_D0
MCU_D1
MCU_D2
MCU_D3
MCU_INT
MCU_CEL
MCU_OEL
MNR04 0R
1
2
3
4
BR4
MNR04 0R
1
8
2
7
3
6
4
5
8
7
6
5
GND
C69
F0.1u/16V
GND
+
FL22
3
C70
A47u/25V
GND
120
R60
100
A20
119
A19
118
1
8
A18
117
2
7 BR12
A17
116
3
6 MNR04 100
A16
115
4
5
114
A15
113
1
8
BR13
A14
112
2
7
MNR04 100 3
A13
111
6
A12
110
4
5
A11
109
1
8
A10
108
2
7 BR14
A9
107
3
6 MNR04 100
A8
106
4
5
A7
105
1
8
BR15
A6
104
2
7
MNR04 100 3
A5
103
6
A4
102
4
5
101
100
A3
99
1
8
A2
98
2
7 BR16
A1
97
3
6 MNR04 100
A0
96
4
5
D0
95
1
8
D1
BR28
94
2
7
D2
MNR04 100 3
93
6
D3
92
4
5
D4
100
91 R64
D5
100
90 R65
R1094 N.M.
89
88
87
86
85
84
R1095 N.M.
83
82
81
10K
160
159
158
157
156
155
154
153
152
151
150
149
148
147
146
145
144
143
142
141
140
139
138
137
136
135
134
133
132
131
130
129
128
127
126
125
124
123
122
121
1
BR17 2
MNR04 47 3
4
BR18
MNR04 47
1
8
2
7
3
6
4
5
3
(N.M.)
10K
+3.3V
GND
GND
CLKIN
(N.M.)
C1048
100pF
R1093
10K
+3.3V
C63
F0.1u/16V
FL18
(N.M.) +3.3V
R1069
R54
R1066
+3.3V
+3.3V
+3.3V
2
GND
R1090
10k
5/6
GND
+
+3.3V
C68
A47u/25V
C1043
18pF
GND
C1033
18pF
PB_D[7:0]
R1091
N.M.
+3.3V
+3.3V
C1044
18pF
100
100
100
+3.3V
(N.M.)
(N.M.)
(N.M.)
10K(N.M.)
R1071
C55
F0.1u/16V
FL13
C56
F0.1u/16V
FL14
C62
F0.1u/16V
N.M.
+3.3V
R32
R1092
FL20
PB_A[7:0]
C65
F0.1u/16V
FL19
GND
GND
GND
GND
PB_D4
PB_D5
PB_D6
PB_D7
PB_D0
PB_D1
PB_D2
PB_D3
MCU_D[7:0]
A[21:0]
D[7:0]
2
1
CS_ML
OEL
WEL
1
A
B
C
D
A
B
C
D
8
26F-E-BT-VK-N
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
CN2
20FE-BT-VK-N
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
CN3
GND
N.M.
R1061
PG
100
0R
7
8
7 FB6
6 MNR04 33
5
1
2
3
4
R69
R70
8
7 FB10
6 MNR04 33
5
1
2
3
4
1
2
3
4
1
2
3
4
1
2
3
4
GND
FB12
8 MNR04 100
7
6
5
FB5
8 MNR04 0R
7
6
5
FB9
8 MNR04 33
7
6
5
FB11
8 MNR04 33
7
6
5
8
7 FB7
6 MNR04 47
5
1
2
3
4
8
7 FB8
6 MNR04 100
5
C61
A47u/35V
1
2
3
4
1
2
3
4
PG
+
GND
+
TP5V
LC3S-Y(N.M.)
GND
ZJSR5101(22000p)
FL15
GND
+
GND
6
GND
10p/50V(N.M.)
ZJSR5101(22000p)
FL16
+3.3V
TP3.3V
LC3S-Y(N.M.)
10p/50V(N.M.)
C1047
TP24V
LC3S-Y(N.M.)
IN3.3V
10p/50V(N.M.)
33pF
C1050
33pF
C1063
ZJSR5101(22000p)
FL17
10p/50V
C1036
C1046
33pF
C1051
10p/50V
C66
+5V
10p/50V
C1045
10p/50V(N.M.)
C1038
C1062
10p/50V(N.M.)
IN5V
10p/50V
C1035
C1040
33pF
C1052
1000pF
C67
C60
A47u/25V
+24V
33pF
C1064
10p/50V(N.M.)
33pF
C1053
GND
100pF
FAX MAIN PWB (MCU I/F)
C43
F0.1u/16V
33pF
6
33pF
C1065
C1059
C1060
33pF
C1056
7
33pF
C1066
C1037
33pF
C1039
C59
A47u/25V
10p/50V(N.M.)
C1057
33pF
8
33pF
C1067
C1041
33pF
10p/50V(N.M.)
C1058
GND
R63
GND
C57
1000p(N.M.)
0R
0R
1
2
3
4
33
PB_A7
PB_A6
PB_A5
PB_A4
PB_A3
PB_A2
PB_A1
PB_A0
PB_D7
PB_D6
PB_D5
PB_D4
PB_D3
PB_D2
PB_D1
PB_D0
MCU_OEL
MCU_CEL
MCU_INT
MCU_D7
MCU_D6
MCU_D5
MCU_D4
MCU_D3
MCU_D2
MCU_D1
MCU_D0
5
5
8
7
6 BR21
5 MNR04 33
BR19
MNR04 0 1
8
2
7
3
6
4
5
1
8
2
7
3
6 BR20
4
5 MNR04 0
R1064
R1085
33pF
C1069
33pF
C1068
C58
F0.1u/16V
33pF
C1054
C1042
33pF
C1055
33pF
C1061
FO-DC550 CIRCUIT DIAGRAM 14 - 36
PB_CS1L
PB_AE0L
PB_WEL
PB_OEL
RESETL
MDM_IRQ
PB_A[7:0]
PB_D[7:0]
MCU_D[7:0]
4
4
R1116
3
B4B-PH-K-S(N.M.)
1
2
3
4
CN5
IN5V
3
GND
0R (1608 N.M.)
IN3.3V
2
2
1
6/6
1
A
B
C
D
FO-DC550 CIRCUIT DIAGRAM 14 - 37
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
B
1SS133
D403
C
REPK
RESOK
CONTK
FDUPK
KEY407
KEY408
KEY410
MEMK
S/SK
KEY411
KEY417
KEY418
R/PK
KEY421
SFTK
KEY406
OT5K
KEY416
BCK
KEY420
OT9K
KEY405
OT4K
KEY415
D
KEY403
OT7K
OT8K
OT2K
OT3K
KEY404
KEY413
KEY414
OT6K
KEY402
OT1K
KEY412
E
E
RMODK
KEY401
CSK
KEY409
SPKK
KEY419
1/1
3
4
1
SHIFT
LED402
MEM
LED403
LS
LED401
1SS133
D402
1SS133
D401
D
1
A
F-KEYIN7
F-KEYIN6
F-KEYIN5
F-KEYIN4
F-KEYIN3
F-KEYIN2
F-KEYIN1
F-KEYIN8
F-KEYSC3
F-KEYSC2
F-KEYSC1
LED_V3
LED_V2
LED_V1
DATA1
C
2
18FE-ST-VK-N
CN401
B
2
3
4
FAX OPERATION PWB
A
5. FAX OPERATION
FO-DC550 CIRCUIT DIAGRAM 14 - 38
PD1
CED1
MM
1
2
MPFS
PD1
D-GND
PPD1
CED1
D-GND
1
2
DSW
CPFS1
FAX
BR
GY
BR
GY
RD
RD
PK
GY
PK
PL
GY
BR
GY
BL
PK
PL
GY
RD
CN26
24V
/MPFS
LEDMFD
MFD
D-GND
CN25
PD1
D-GND
CN16
LEDPPD1
PPD1
D-GND
CN15
1 24V
2 24V1(DSWS)
1
2
3
4
5
1
2
1
2
3
CN7
1 CED1
2 D-GND
CN10
24V
/CPFS1
1
2
BL
PK
PL
GY
RD
CN12
24V
/RRS
1
2
3
4
5
1
2
PMCLK-A
PMRDY
/PMD
P-GND
24V
RRS
1
2
5
6
7
8
PM
CN23
TMA-O
TMB-O
24V
24V
/MM
MMLD
GND
GND
Shifter
Motor
LSU
PK
GY
OR
GY
PL
PK
GY
LB
1
2
CN19
LEDPOD
POD
D-GND
TM
1
2
3
CN13
24V
/DMT0
/DMT1
/DMT2
/DMT3
1
2
3
4
5
CN6
INT24V
INT24V
/MM
MMLD
P-GND
P-GND
PK
LB
GY
CN11
VFM
/VFMCNT
P-GND
1
3
4
8
7
4
3
2
1
OR
GY
PL
PK
GY
LB
PK
GY
PL
GY
1
2
3
4
5
CN27
24V
/SFTMT0
/SFTMT1
/SFTMT2
/SFTMT3
6
1
3
2
5
4
8
7
1
2
CN22
LEDPPD2
PPD2
D-GND
RTH-IN
AN-GND
1
2
3
4
5
5V1(DSWS)
D-GND
/VIDEO
S/H
D-GND
/LDEN
/H SYNC
D-GND
RTH
AN-GND
1
2
1
2
3
PK
BL
GY
PL
GY
CN20
INT5V
D-GND
/VIDEO
SHOLD
D-GND
/LDEN
NC
/SYNC
D-GND
D-GND
P-GND
PMCLK-A
PMRDY
/PMD
P-GND
24V
H
S
Y
N
C
LEDPPD2
PPD2
D-GND
1
2
3
PK
BL
GY
2
3
5
6
7
8
9
10
11
12
13
14
15
16
17
18
POD
Duplex
Motor
VFM
RTH
PPD2
PK
BL
GY
MCU
PWB
1
2
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
CN1(2/2)
D-GND
P-GND
D-GND
3.3VIN
EN5V
3.3VIN
5V
/POFF
12VIN
24V
FW
24V
/PR
HLOUT
P-GND
P-GND
1
3
5
7
CN1(1/2)
INT5V
INT24V
/BIAS
/TC
/GRIDL
/MC
CN5
24V
TCS
DVSEL
D-GND
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
1
2
3
4
CN4
OUT_A+
OUT_B+
OUT_AOUT_B-
CN3
(AFE_DB0)
(AFE_DB1)
(AFE_DB2)
(AFE_DB3)
(AFE_DB4)
D-GND
(AFE_DB6)
(AFE_DB5)
MHPS
(AFE_DB7)
(AFE_SCK)
D-GND
(ADCLK)
(AFE_SEN)
CCD_PHI1
D-GND
CCD_PHI2
(AFE_SDI)
CCD-CP
(BSAMP)
CCD-RS
D-GND
CCD-TG
(VSAMP)
D-GND
EN5V
12V
12V
VCL
VCL
P-GND
P-GND
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
CN2
D-GND
KEYSC3
KEYSC2
KEYSC1
BZR
LCDRS
LCDE
LCDDB4
LCDDB5
LCDDB6
LCDDB7
SELIN3
SELIN2
SELIN1
OP-DATA
OP-LATCH
OP-CLK
PSL
KEYIN
PSW
DRST
D-GND
5VEN
D-GND
5V
D-GND
VCC3
D-GND
GY
GY
GY
BL
OR
BL
OR
BR
PL
RD
PK
RD
PK
PL
GY
GY
OR
RD
YE
BR
LB
PK
RD
PL
BR
GY
RD
GY
GY
GY
BL
OR
BL
OR
BR
PL
RD
PK
RD
PK
PL
GY
GY
OR
RD
YE
BR
LB
PK
RD
GY
CN1
D-GND
KEYSC3
KEYSC2
KEYSC1
BZR
LCDRS
LCDE
LCDDB4
LCDDB5
LCDDB6
LCDDB7
SELIN3
SELIN2
SELIN1
OP-DATA
OP-LATCH
OP-CLK
PSL
KEYIN
PSW
DRST
D-GND
5VEN
D-GND
5V
D-GND
VCC3
D-GND
1
2
5
6
7
8
CN101
D-GND
P-GND
D-GND
3.3VIN
EN5V
3.3VIN
5V
/POFF
12VIN
24V
FW
24V
/PR
HLOUT
P-GND
P-GND
CN10
BIAS
F-GND
CN6
INT5V
INT24V
/BIAS
/TC
/GRIDL
/MC
CN1
(AFE_DB0)
(AFE_DB1)
(AFE_DB2)
(AFE_DB3)
(AFE_DB4)
D-GND
(AFE_DB6)
(AFE_DB5)
MHPS
(AFE_DB7)
(AFE_SCK)
D-GND
(ADCLK)
(AFE_SEN)
CCD_PHI1
D-GND
CCD_PHI2
(AFE_SDI)
CCD-CP
(BSAMP)
CCD-RS
D-GND
CCD-TG
(VSAMP)
D-GND
EN5V
12V
12V
VCL
VCL
P-GND
P-GND
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
Scanner
Motor
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
MC
1
2
BC
TC
BR
GY
POWER
SUPPLY
PWB
RD
WH
WH
RD
CN001
CN002
HLL
HLN
L
N
1
2
RD
CARRIAGE UN
HVT PWB
CN9
1
3
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
CN11 GRID
MCFB
CCD
PWB
VCL
P-GND
OP
PWB
CN2
D-GND
D-GND
F-KEYIN7
F-KEYIN6
F-KEYIN5
F-KEYIN4
F-KEYIN3
F-KEYIN2
F-KEYIN1
F-KEYIN8
F-KEYSC3
F-KEYSC2
F-KEYSC1
LED_V3
LED_V2
LED_V1
DATA1
D-GND
CN3
DRST
D-GND
1
4
DRST
D-GND
CN1
D-GND
D-GND
F-KEYIN7
F-KEYIN6
F-KEYIN5
F-KEYIN4
F-KEYIN3
F-KEYIN2
F-KEYIN1
F-KEYIN8
F-KEYSC3
F-KEYSC2
F-KEYSC1
LED_V3
LED_V2
LED_V1
DATA1
D-GND
BK
WH
1
2
6
5
8
1
2
1
2
6
5
8
120V
ONLY
HLL
HLN
24V
TCS
DVSEL
D-GND
BIAS
INVERTER
PWB
FAX
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
DRST
1
2
BK
WH
TCS
CL
CL
DV
un
HL
THERMOSTAT
WH
WH
WH
WH
FAX OP PWB
6. ACTUAL WIRING DIAGRAM
(1) MCU SECTION (1/3)
PWB
MCU
CN24
D-GND
3
6
SDSW
5
SPID
7
SB4B
8
5V
24V
11
12
/SPUS
D-GND
1
2
SPPD
LEDSPPD 4
SPMT-1
19
SPMT-3
20
SPMT-2
21
SPMT-0
22
24Vmir
23
24Vmir
24
24V
13
/SPFS
14
24V
15
/SRRC
16
24V
17
/SGS
18
OR
OR
RD
BR
GY
BR
PK
PL
PK
BL
BR
RD
RD
RD
PK
RD
PL
RD
BL
FO-DC550 CIRCUIT DIAGRAM 14 - 39
RD
BL
RD
PL
RD
PK
RD
BR
GY
PL
BL
GY
PL
BL
1
2
1
2
1
2
1
2
1
2
3
4
5
24V
/SGS
24V
/SRRC
24V
/SPFS
24V
/SPUS
D-GND
SDSW
SPID
SB4B
5V
2
1
2
1
2
1
2
1
5
4
3
2
1
OR
GY
PL
BL
D-SPF UNIT
PL
PK
BL
BR
RD
RD
GY
BR
PK
5
4
3
2
1
3
1
6
4
2
5
SPMT
PWB
SENSOR
SGS
(RSPF only)
SRRC
SPFS
SPMT-1
SPMT-3
SPMT-2
SPMT-0
24Vmir
24Vmir
SPPD
SPUS
D-GND
SDSW
SPID
SB4B
5V
(2) RSPF/SPF SECTION (2/3)
Personal Computer(USB PORT)
Personal Computer (IEEE1284 port)
CN16
D-GND
DIR3
/IT3
/SELIN3
/AFEED3
/STB
/FLT
SLCT
PERR
PBSY
/PACK
P7
P6
P5
P4
P3
P2
P1
P0
/RESET
VCC3
5V
5V
D-GND
CN33
5V USB
DATA DATA +
D-GND
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
FO-DC550 CIRCUIT DIAGRAM 14 - 40
1
2
3
4
PWB
MCU
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
CN37
D-GND
MDM_IRQ
(/FAX_RST)
PB_MOE
PB_NWE
PB_NAE0
PB_NCS1
D-GND
PB_ADDR0
PB_ADDR1
PB_ADDR2
PB_ADDR3
PB_ADDR4
PB_ADDR5
PB_ADDR6
PB_ADDR7
D-GND
PB_DATA0
PB_DATA1
PB_DATA2
PB_DATA3
PB_DATA4
PB_DATA5
PB_DATA6
PB_DATA7
D-GND
CN38
D-GND
MSU_ST1
/CS4
/RD
MODEM_IN
D0
D1
D2
D3
D4
D5
D6
D7
P-GND
24V
D-GND
EN5V
VCC3
VCC3
D-GND
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
CN1
D-GND
MSU_ST1
/CS4
/RD
MODEM_IN
D0
D1
D2
D3
D4
D5
D6
D7
P-GND
24V
D-GND
EN5V
VCC3
VCC3
D-GND
CN2
D-GND
MDM_IRQ
(/FAX_RST)
PB_MOE
PB_NWE
PB_NAE0
PB_NCS1
D-GND
PB_ADDR0
PB_ADDR1
PB_ADDR2
PB_ADDR3
PB_ADDR4
PB_ADDR5
PB_ADDR6
PB_ADDR7
D-GND
PB_DATA0
PB_DATA1
PB_DATA2
PB_DATA3
PB_DATA4
PB_DATA5
PB_DATA6
PB_DATA7
D-GND
PWB
FAX
CN10
VOUT1
VOUT2
1
2
TO TEL
SPEAKER
(3) I/F & FAX SECTION (3/3)
[15] FIRMWARE DOWNLOAD
PROCEDURES
2) Select "Option" → "Serial Number Setting" on the menu bar.
[Preparation]
Write the download data (extension .dwl) into the main unit.
A USB port is required for the PC.
Create "MaintenanceTool " flooder in the PC, and copy the following
files to the folder.
Necessary for program download
• Maintenance.exe (← Tool program)
• ProcModelB.mdl
• ProcModelC.mdl
• ProcModelE.fmt
• ProcModelE.ini
3) Set the serial number according to the following.
• ProcModelE.mdl
Driver
• Drivers/2kXP/Mainte.inf (For Windows XP/2000)
• Drivers/Win9xME/Mainte.inf (For Windows Me/98SE)
• Drivers/Win9xME/UsbScan.sys (For Windows Me/98SE)
Download file
• Download file (extension .dwl)
Note: Copy the download data file (extension .dwl) to the folder in
which the maintenance program is included.
When making a folder for the maintenance tool in the PC, do not
put a long folder name in the absolute path.
[Example]
Erroneous case: c:\Mainte nance Tool Download
Proper case:
c:\MaintenanceTool
1. Initial setting
(Serial number setting procedures)
The serial number is set to the PC which is used for downloading. Setting is required once only, and there is no need to set again when
rebooting the program.
Note: This setting is required only when downloading the default data
of E2PROM, and is not required when downloading firmware
only.
1) PC side: Boot "Maintenance.exe" and select "AR-168/M150/M155
series" in the "Select Model" menu.
(Only to set the serial number, the PC should not be connected to
the machine.)
Product Code (P): Enter number (0 – 99)
Enter the product code of “3.”
ID Code(I):
Enter number (0 – 99)
Assign an individual code to each PC uses
“Maintenance.exe.”
After completion setting, press [OK] key.
4) The serial number has been assigned.
2. Download procedures
1) Main unit side: Execute Test command No. 49-01 (Flash ROM program write mode).
Check that "DOWNLOAD MODE" is displayed on the LCD of the
operation panel. (Press and hold [CA] key and [DOWN] key (left
key) together, and turn on the power simultaneously.)
2) Connect machine and the PC with a USB cable. (Connect it to the
USB port on the main unit without fail.
3) PC side: Boost "Maintenance.exe" and select "AR-168/M150/M155
series" in the Select Model menu.
FO-DC550 FIRMWARE DOWNLOAD PROCEDURES 15 - 1
4) PC side: Check that the "Simulation Command List" tree is displayed on the integration maintenance program.
8) PC side: Specify the download file (*****.dwl) to be used.
5) PC side: When the integration maintenance program is boosted
and "The copier is not turned on." is displayed at the bottom of display, select "File" → "Reconnect" on the menu bar.
9) PC side: When a download file is specified, downloading is performed automatically.
6) PC side: Check that trees are displayed in the "Special (MCU/
IMC2/Facsimile)" folder in the integration maintenance program. (If
trees are not displayed, check that the USB connector is connected, and select "Reconnect" in procedure 5) again.)
10) PC side: When download is completed, the following message is
displayed.
7) PC side: Double-click "Special (MCU/IMC2/Facsimile)" in the main
tree to develop its sub trees, and double-click "Download DWL
Data Area" in the sub trees.
Note: Since, however, the machine enters the download data write
state, do not turn OFF the power of the machine at this moment.
11) Main unit side: Wait until "DOWNLOAD COMPLETE!" is displayed
on the LCD of the operation panel. When "DOWNLOAD COMPLETE!" is displayed, download is completed.
Turn OFF the power of the machine, and disconnect the USB
cable.
12) Terminate the integration maintenance program, and turn ON the
machine again.
Download is completed with the above procedures.
FO-DC550 FIRMWARE DOWNLOAD PROCEDURES 15 - 2
Note: When another machine is connected, connect the USB cable
again and select "File" → "Reconnect" on the menu bar of the
integration maintenance program. Repeat the above procedures
from 5).
∗ Inhibition during download (Important)
4) PC side: Check that the "Simulation Command List" tree on the
integration maintenance program.
5) PC side: Boot the integration maintenance program. If "The copier
is not turned on." is displayed, select "File" → "Reconnect" on the
menu bar.
If download is failed, the next download may not be executed. Use
great care not to execute the following items during download.
• Never turn off the machine.
• Never disconnect the download cable (USB cable).
* If the above inhibition item occurs during downloading,
turn OFF/ON the power.
1) When "DOWNLOAD MODE" is displayed on the operation panel,
execute the download procedure again.
2) If "DOWNLOAD MODE" is not displayed on the operation panel,
turn OFF the power and press and hold [CA] key and [DOWN] key
(left key) and turn ON the power. Check that "DOWNLOAD MODE"
is displayed on the operation panel, and execute the download procedure again.
If "DOWNLOAD MODE" is not still displayed, replace the MCU with
a new one.
3. Version acquisition procedures
1) Main unit side: Execute Test command No. 49-01 (Flash ROM program write mode).
6) PC side: Check that trees are displayed on "Special (MCU/IMC2/
Facsimile" in the integration maintenance program. (If trees are not
displayed, check that the USB cable is connected and select
"Reconnect" again in procedure 5).
Check that "DOWNLOAD MODE" is displayed on the operation
panel of the main unit. (Press and hold [CA] key and [DOWN] key
(left key) together, and turn on the power simultaneously.)
2) Connect the machine and the PC with a USB cable.
3) PC side: Boost "Maintenance.exe" and select "AR-168/M150/M155
series" in the "Select Model" menu.
FO-DC550 FIRMWARE DOWNLOAD PROCEDURES 15 - 3
7) PC side: Double-click "Special (MCU/IMC2/Facsimile)" in the main
tree items to develop its sub trees. Select "Get Version" in the sub
trees.
8) Check that the following display is shown.
4) PC side: Check that "Simulation Command List" tree is displayed in
the integration maintenance program.
5) PC side: Boot the integration maintenance program. If "The copier
is not turned on." is displayed on the lower side of the display,
select "File" → "Reconnect" on the menu bar.
With the above procedures, version acquisition is completed.
• The display of "**.**" means its version is not downloaded. The
downloaded versions are displayed in a version number as shown in
“MCU Boot Version” and “MCU program Version”.
4. EEPROM data acquisition procedure
6) PC side: Check that trees are displayed on "Special (MCU/IMC2/
Facsimile" in the integration maintenance program. (If trees are not
displayed, check that the USB cable is connected and select
"Reconnect" again in procedure 5).
EEPROM data is acquired to the PC. Use this procedure as data maintenance of EEPROM.
1) Main unit side: Execute Test command No. 49-01 (Flash ROM program write mode).
Check that "DOWNLOAD MODE" is displayed on the operation
panel of the main unit. (Press and hold [CA] key and [DOWN] key
(left key) together, and turn on the power simultaneously.)
2) Connect the machine and the PC with a USB cable.
3) PC side: Boot "Maintenance.exe" and select "AR-168/M150/M155
series" in the "Select Model" menu.
FO-DC550 FIRMWARE DOWNLOAD PROCEDURES 15 - 4
7) PC side: Double-click "Special (MCU/IMC2/Facsimile)" to develop
its sub trees, and select "Upload EEPROM Data Area" in the sub
trees.
5. Installing procedures
<USB integration maintenance program installation>
Driver installation is made on plug-and-play.
<Installation on Windows XP>
1) Main unit side: Execute Test command No. 49-01 (Flash ROM program write mode).
Check that "DOWNLOAD MODE" is displayed on the LCD of the
operation panel. (Press and hold [CA] key and [DOWN] key (left
key) together, and turn on the power simultaneously.)
2) Connect the machine and the PC with a USB cable.
3) The following display is shown.
Select [Install from a list or specific location] and press <Next> button.
8) PC side: Enter a desired file name, and select "Save."
4) Select [Include this location in the search;]. If the search location is
not the folder which includes the maintenance tool driver
(Mainte.inf), select <Browse>. If the search location is the folder
which includes the maintenance tool driver, press <Next> button to
go to procedure 7).
9) PC side: When upload is completed, the complete message is displayed.
With the above procedure, the EEPROM data acquisition is completed.
Data acquired by the EEPROM data acquisition procedure are saved
in a file with extension of .eep.
FO-DC550 FIRMWARE DOWNLOAD PROCEDURES 15 - 5
5) Select the folder which includes the maintenance tool driver
(Mainte.inf) and press <OK> button.
8) When the following display is shown, installation is completed.
Press <Finish> button.
(Suppose that the driver is included in C:\MaintenanceTool\Drivers\
2kXp folder.)
With the above procedures, installation (on Windows XP) of the integration maintenance program is completed.
6) Check the path to the folder which includes the maintenance tool
driver (Mainte.inf), and press <Next> button.
<Installation on Windows 2000>
1) Main unit side: Execute Test command No. 49-01 (Flash ROM program write mode).
Check that "DOWNLOAD MODE" is displayed on the LCD of the
operation panel. (Press and hold [CA] key and [DOWN] key (left
key) together, and turn on the power simultaneously.)
2) Connect the machine and the PC with a USB cable.
3) Check that the Found New Hardware Wizard is displayed, and
press <Next> button.
7) When the following display is shown, press [Continue Anyway] button.
4) Select [Search for a suitable driver for my device] and press <Next>
button.
FO-DC550 FIRMWARE DOWNLOAD PROCEDURES 15 - 6
5) Select [Specify a location] and press <Next> button.
8) Check that the path to the folder which includes the maintenance
tool driver (Mainte.inf) is displayed, and press <OK> button.
(Suppose that the maintenance tool driver is included in
C:\MaintenanceTool\Drivers\2kXp folder.)
6) Select [Include this location in the search;]. If the search location is
not the folder which includes the maintenance tool driver
(Mainte.inf), select <Browse>. If the search location is the folder
which includes the maintenance tool driver, press <Next> button to
go to procedure 9).
9) Press <Next> button to start installation.
10) When the following display is shown, installation is completed.
7) Specify the folder which includes the maintenance tool driver
(Mainte.inf), and press <Open> button.
Press <Finish> button.
11) Restart the PC.
With the above procedures, installation (on Windows 2000) of the integration maintenance program is completed.
FO-DC550 FIRMWARE DOWNLOAD PROCEDURES 15 - 7
<Installation on Windows Me>
1) Main unit side: Execute Test command No. 49-01 (Flash ROM program write mode).
6) Check that the path to the folder which includes the maintenance
tool driver (Mainte.inf) is displayed, and press <Next> button.
Check that "DOWNLOAD MODE" is displayed on the LCD of the
operation panel. (Press and hold [CA] key and [DOWN] key (left
key) together, and turn on the power simultaneously.)
2) Connect the machine and the PC with a USB cable.
3) The following display is shown on the PC side.
Select [Specify the location of the driver], and press <Next> button.
7) When the following display is shown, installation is completed.
Press <Finish> button.
4) Select [Specify a location], specify the folder which includes the
maintenance tool driver (Mainte.inf) as the search location, and
press <Next> button.
If the search location does not include the maintenance tool driver
(Mainte.inf), press <Browse> button to specify the folder which
includes the maintenance tool driver (Mainte.inf).
(Suppose that the maintenance tool driver is included in
C:\MaintenanceTool\Drivers\Win9xMe folder.)
8) Restart the PC.
With the above procedures, installation (on Windows ME) of the integration maintenance program is completed.
5) Select the folder which includes
(Mainte.inf), and press <OK> button.
maintenance
tool
driver
(Suppose that the driver is included in
C:\MaintenanceTool\Drivers\Win9xMe folder.)
FO-DC550 FIRMWARE DOWNLOAD PROCEDURES 15 - 8
LEAD-FREE SOLDER
The PWB’s of this model employs lead-free solder. The “LF” marks indicated on the PWB’s and the Service Manual mean “Lead-Free” solder.
The alphabet following the LF mark shows the kind of lead-free solder.
Example:
<Solder composition code of lead-free solder>
Lead-Free
5mm
Solder composition
code (Refer to the
table at the right.)
a
Solder composition
Solder composition code
Sn-Ag-Cu
a
Sn-Ag-Bi
Sn-Ag-Bi-Cu
b
Sn-Zn-Bi
z
Sn-In-Ag-Bi
i
Sn-Cu-Ni
n
Sn-Ag-Sb
s
Bi-Sn-Ag-P
Bi-Sn-Ag
p
(1) NOTE FOR THE USE OF LEAD-FREE SOLDER THREAD
When repairing a lead-free solder PWB, use lead-free solder thread.
Never use conventional lead solder thread, which may cause a breakdown or an accident.
Since the melting point of lead-free solder thread is about 40°C higher than that of conventional lead solder thread, the use of the exclusive-use
soldering iron is recommendable.
(2) NOTE FOR SOLDERING WORK
Since the melting point of lead-free solder is about 220°C, which is about 40°C higher than that of conventional lead solder, and its soldering capacity is
inferior to conventional one, it is apt to keep the soldering iron in contact with the PWB for longer time. This may cause land separation or may exceed
the heat-resistive temperature of components. Use enough care to separate the soldering iron from the PWB when completion of soldering is
confirmed.
Since lead-free solder includes a greater quantity of tin, the iron tip may corrode easily. Turn ON/OFF the soldering iron power frequently.
If different-kind solder remains on the soldering iron tip, it is melted together with lead-free solder. To avoid this, clean the soldering iron tip after
completion of soldering work.
If the soldering iron tip is discolored black during soldering work, clean and file the tip with steel wool or a fine filer.
CAUTION FOR BATTERY REPLACEMENT
(Danish)
ADVARSEL !
Lithiumbatteri – Eksplosionsfare ved fejlagtig håndtering.
Udskiftning må kun ske med batteri
af samme fabrikat og type.
Levér det brugte batteri tilbage til leverandoren.
(English)
Caution !
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type
recommended by the manufacturer.
Dispose of used batteries according to manufacturer’s instructions.
(Finnish)
VAROITUS
Paristo voi räjähtää, jos se on virheellisesti asennettu.
Vaihda paristo ainoastaan laitevalmistajan suosittelemaan
tyyppiin. Hävitä käytetty paristo valmistajan ohjeiden
mukaisesti.
(French)
ATTENTION
Il y a danger d’explosion s’ il y a remplacement incorrect
de la batterie. Remplacer uniquement avec une batterie du
même type ou d’un type équivalent recommandé par
le constructeur.
Mettre au rebut les batteries usagées conformément aux
instructions du fabricant.
(Swedish)
VARNING
Explosionsfara vid felaktigt batteribyte.
Använd samma batterityp eller en ekvivalent
typ som rekommenderas av apparattillverkaren.
Kassera använt batteri enligt fabrikantens
instruktion.
(German)
Achtung
Explosionsgefahr bei Verwendung inkorrekter Batterien.
Als Ersatzbatterien dürfen nur Batterien vom gleichen Typ oder
vom Hersteller empfohlene Batterien verwendet werden.
Entsorgung der gebrauchten Batterien nur nach den vom
Hersteller angegebenen Anweisungen.
CAUTION FOR BATTERY DISPOSAL
(For USA, CANADA)
"BATTERY DISPOSAL"
THIS PRODUCT CONTAINS A LITHIUM PRIMARY
(MANGANESS DIOXIDE) MEMORY BACK-UP BATTERY
THAT MUST BE DISPOSED OF PROPERLY. REMOVE THE
BATTERY FROM THE PRODUCT AND CONTACT YOUR
LOCAL ENVIRONMENTAL AGENCIES FOR INFORMATION
ON RECYCLING AND DISPOSAL OPTIONS.
"TRAITEMENT DES PILES USAGÉES"
CE PRODUIT CONTIENT UNE PILE DE SAUVEGARDE DE
MÉMOIRE LITHIUM PRIMAIRE (DIOXYDE DE MANGANÈSE)
QUI DOIT ÊTRE TRAITÉE CORRECTEMENT. ENLEVEZ LA
PILE DU PRODUIT ET PRENEZ CONTACT AVEC VOTRE
AGENCE ENVIRONNEMENTALE LOCALE POUR DES
INFORMATIONS SUR LES MÉTHODES DE RECYCLAGE ET
DE TRAITEMENT.
COPYRIGHT © 2004 BY SHARP CORPORATION
All rights reserved.
Printed in Japan.
No part of this publication may be reproduced,
stored in a retrieval system, or transmitted,
in any form or by any means,
electronic; mechanical; photocopying; recording or otherwise
without prior written permission of the publisher.
Trademark acknowledgements
• Microsoft® Windows® operating system is a trademark or copyright of Microsoft
Corporation in the U.S.A. and other countries.
• Windows® 95, Windows® 98, Windows® Me, Windows NT® 4.0, Windows® 2000,
and Windows® XP are trademarks or copyrights of Microsoft Corporation in the
U.S.A. and other countries.
• IBM and PC/AT are trademarks of International Business Machines Corporation.
• Acrobat® Reader Copyright® 1987- 2002 Adobe Systems Incorporated. All rights
reserved. Adobe, the Adobe logo, Acrobat, and the Acrobat logo are trademarks of
Adobe Systems Incorporated.
• All other trademarks and copyrights are the property of their respective owners.
SHARP CORPORATION
Digital Document System Group
Products Quality Assurance Department
Yamatokoriyama, Nara 639-1186, Japan
2004 May Printed in Japan