Craftsman 139.18857 Owner`s manual

®
OWNER’S
MANUAL
MD
Model No.
139.18847
139.18857
®
GARAGE DOOR OPENER
1/2 HP
The Chamberlain Group, Inc.
Cover - SEARS
4/16/92
For Residential Use
Only
■
Caution:
Read and follow all
safety rules and
operating instructions
before first use of this
product.
■
■
■
■
■
■
Fasten the manual
near the garage door
after installation.
■
Safety Precautions
Assembly
Installation
Adjustment
Care and Maintenance
Operation
Troubleshooting
Parts List
®
Sears Canada, Inc., Toronto, Ontario M5B 2B8
MD
Contents
Page
A review of safety alert symbols.................................2
You'll need tools..........................................................3
Safety information regarding garage door
locks and ropes.........................................................3
Testing your garage door for sticking,
binding and balance..................................................3
Illustration of sectional door installation .....................4
Illustration of one-piece door installation ....................5
Carton inventory..........................................................6
Hardware inventory.....................................................7
Assembly section - pages 8 – 11
Assemble T-rail .........................................................8
Attach cable pulley bracket.......................................8
Install trolley ..............................................................9
Fasten T-rail to opener .............................................9
Install chain/cable ...................................................10
Attach sprocket cover .............................................10
Tighten the chain and cable ...................................11
Installation section - pages 11 – 27
Installation safety instructions.................................11
Determine header bracket location
Sectional door ......................................................12
One-piece door ....................................................13
Install the header bracket .......................................14
Attach the T-rail to header bracket .........................15
Position the opener.................................................16
Hang the opener .....................................................17
Install the door control ............................................18
Contents
Page
Install the lights and lenses ......................................19
Attach emergency release rope and handle ...........19
Electrical requirements.............................................20
Safety reversing sensor information ........................21
Install the safety reversing sensor .....................22, 23
Fasten door bracket (sectional door) .......................24
Fasten door bracket (one-piece door) .....................25
Connect door arm to trolley (sectional door) ...........26
Connect door arm to trolley (one-piece door)..........27
Adjustment section - pages 28 – 30
Travel limit adjustments ...........................................28
Force adjustments....................................................29
Test the safety reversing sensor..............................30
Test the safety reverse system ...............................30
Operation safety instructions .....................................31
Care of your opener ...................................................31
Maintenance schedule ...............................................31
Operation of your opener ...........................................32
Receiver and remote control programming ...............33
Having a problem? ...............................................34, 35
Repair parts, rail assembly.........................................36
Repair parts, installation.............................................36
Repair parts, opener assembly..................................37
Accessories ................................................................38
Index ...........................................................................39
How to order repair parts ...........................................40
Maintenance agreement ............................................40
Warranty .....................................................................40
Start by Reviewing these Important Safety Alert Symbols
When you see these Safety Symbols on the following pages, they will alert you to the possibility of
serious injury or death if you do not comply with the corresponding instructions. The hazard may
come from something mechanical or from electric shock. Read the instructions carefully.
WARNING
WARNING WARNING
WARNING
WARNING
WARNING
Mechanical
Electrical
When you see this Safety Symbol on the following pages, it will alert you to the possibility of damage
to your garage door and/or the garage door opener if you do not comply with the corresponding
instructions. Read the instructions carefully.
CAUTIONCAUTION
CAUTION
WARNING
WARNING
WARNING
This garage door opener is designed and tested to offer safe service provided it is installed, operated,
maintained and tested in strict accordance with the safety instructions contained in this manual.
2
You'll Need Tools
During assembly, installation and adjustment of the opener, instructions will call for hand tools shown below.
Pencil
Carpenter's
Level
Hack Saw
2
1
Tape Measure
Wire Cutters
WARNING
Claw Hammer
Drill
3/16", 5/16", and
5/32" Drill Bits
Stepladder
Pliers
Adjustable End Wrench
Screwdriver
1/2" and 7/16" Sockets
and Wrench
WARNING CAUTION
WARNING
To avoid damage to the garage door and
opener, disable locks before installing and
operating the opener. Use a wood screw or nail
to hold locks in the "open" (unlocked)
position.
Operation at other than 120V 60 Hz will cause
opener malfunction and damage.
An unbalanced garage door might not reverse
when required and someone under the door
could be seriously injured or killed.
If your garage door binds, sticks or is out of
balance, call for professional garage door
service. Garage doors, door springs, cables,
pulleys, brackets and their hardware are under
extreme tension and can cause serious injury
or death. Do not try to loosen, move or adjust
them yourself!
Niveau de
Ropes left on a garage door could
menuisier cause
someone to become entangled and killed.
Remove all ropes connected to the door before
installing and operating the opener.
CAUTION
Crayon
WARNING
AVERTISSEMENT
Scie à métaux
Before you begin, complete the following
test to
make
sure your door is balanced, and is not
Ruban
à mesurer
sticking or binding:
Pince coupante
• Lift the door about halfway as shown. Release the
Marteauby
door. It should stay in place, supported entirely
its
springs.
Forets de 3/16 de po,
Pince universelle
de 5/16
de po and
et 5/32lower
de po the door to see if there is any
• Raise
binding or sticking.
Clé à molette
1
Perceuse
Identify the type and height of your door and any
special conditions that exist and any additional
materials that may be required
by referring to the lists
Escabeau
on page 4 or page 5.
Clé à douille et douilles
2
Tournevis
de 1/2 po et 7/16 de po
AVERTISSEMENT
AVERTISSEMENT
ATTENTION
AVERTISSEMENT
ATTENTION
ONE-PIECE
ONE-PIECE
DOORDOOR
SECTIONAL
SECTIONAL
DOORDOOR
3
W
FIN
Su
fa
SECTIONAL Door Installation
vertical reinforcement
Before you begin, survey your garage area to see whether anyHorizontal
of the and
conditions
below apply to your installation.
is needed for lightweight garage doors
(fiberglass, steel, aluminum, door with glass panels, etc.).
See page 24 for details.
Horizontal and vertical reinforcement
is needed for lightweight garage doors
(fiberglass, steel, aluminum, door with glass panels, etc.).
See page 24 for details.
Slack in Chain Tension
is Normal When
Garage Door is Closed
FINISHED CEILING
Support bracket &
fastening hardware
Header Wall
is required.
See page 17.
Slack in Chain Tension
is Normal When
Garage Door is Closed
Header Wall
Extension Spring
OR
Torsion Spring
———
———
Extension Spring
Door Center
OR
Torsion Spring
——
———
Safety
Reversing
Sensor
Door Center
Access Door
———
Floor must be level
across width of door
——
Safety Safety Reversing Sensor
Reversing
Sensor
Closed Position
Floor must be level
across width of door
Header
Bracket
Safety Reversing Sensor
Based on your particular requirements, there are
several installation steps which might call for
Closed Position
materials and/or hardware not included in the carton.
Header Cable Pulley
• Step 1, page 12
- LookBracket
at the wall or ceiling above
Bracket
be
the garage door. The headerTrolley
bracketRailmust
Assembly
Cable
securely fastened to structural supports.
• Step 5, page 17 - Do you have a finished ceiling in
your garage? If so,Garage
a support bracketEmergency
and
Door
additional fasteningSpring
hardware may be Release
required.
Rope & Handle
• Safety reversing sensor, page 21 - Depending
upon garage construction, Straight
wood
Door blocks may need
Arm
to be fastened to mounting locations
before
sensors are installed.
Curved
Door
• Step 10, page 22 - Alternate
floor mounting of the
Header
Arm
safety Wall
reversing Door
sensor
will
require hardware not
Bracket
provided.
Garage
Door
• Step 11,
page 24 - Do you have a steel, aluminum,
fiberglass or glass panel door? If so, horizontal
and vertical reinforcement is required.
• Look at the garage door where it meets the
floor. It must close on the floor all the way
across. Otherwise, the safety reverse system
may not work properly. See page 30. Floor or
door should be repaired.
Cable Pulley
Bracket
Trolley
Cable
Garage
Door
Spring
Closed Position
Rail Assembly
Emergency
Release
Rope & Handle
Straight
Door
Arm
Header
Wall
Garage
Door
You may find it
helpful to refer
Open Position
back to this page
Curved
Cable
Door T-rail
asTrolley
you proceed
Arm
with the installation
Door Bracket
of your opener.
Straight
Emergency
• If your door is more than 7 feet
high, see
the rail
Door
Release
extensionGarage
kits available on page
38.
Arm
Rope
&
Door
Curved
Handle
• The opener can be
installed
within 2 feet to
the left
Door
Arm
or right of the door center if there is a torsion spring
or center bearing plate in the way of the header
bracket or door bracket area. If your door has
extension springs, the opener must be installed
in the center of the door. See pages 12 and 24.
• Do you have an access door in addition to the
garage door? If not, Model 18752 Outside
Trolley Release is required. See page 38.
4
Gara
Doo
One-Piece Door without Track
ONE-PIECE Door Installation
Before you begin, survey your garage area to see
whether any of the conditions below apply to your
installation.
FINISHED CEILING
Support bracket
& fastening hardware
may be required.
See page 17.
Slack in Chain Tension
is Normal When
Garage Door is Closed
Header
Wall
Closed Position
Cable
Pulley Bracket
Access Door
Trolley
Cable
Header
Bracket
T-rail
The Chamberlain Group, Inc.
Door Bracket
One-Piece Door with
Track Installation (CableEmergency
-Release
Canada)
Curved
Rope
& Handle
3/3/93
Straight
Door
Header
Wall
Safety
Reversing
Gap between floor and bottom of Sensor
Safety
door must not exceed 1/4"
Reversing Sensor
Based on your particular requirements, there are
several installation steps which might call for materials
and/or hardware not included in the carton.You may
want to review these steps before beginning:
• Step 1, page 13 - Look at the wall or ceiling above
the garage door. The header bracket must be
securely fastened to structural supports.
• Step 5, page 17 - Do you have a finished ceiling in
your garage? If so, a support bracket and additional
fastening hardware (not supplied) may be required.
• Safety reversing sensor, page 21 - Depending on
garage construction, wood blocks may need to be
securely fastened to mounting locations before
sensors are installed.
• Step 10, page 22 - Alternate floor mounting of the
safety reversing sensor will require hardware that
is not provided.
• Step 11, page 25 - Generally, a one-piece door
does not require reinforcement. If your door is
lightweight, you can refer to the information
relating to sectional doors on page 24.
• Step 11, page 25 - Depending on your door's
construction, you might need additional mounting
hardware for the door bracket.
• Do you have an access door in addition to the
garage door? If not, Model 18752 Outside Trolley
Release is required. See page 38.
• The gap between the bottom of the garage
door and the floor cannot exceed 1/4".
Otherwise, the safety reverse system may not
work properly. See page 30. The floor or the door
should be repaired.
Garage
Door
Door
Arm
Arm
One-Piece Door with Track
Slack in Chain
Tension is Normal
When Garage Door is Closed
Access
Door
Floor must be level
Safety
across width of door
Reversing Sensor
Safety
Reversing
Sensor
Closed Position
Cable
Pulley Bracket
Cable
Trolley
Chain
Header
Wall
Header
Bracket
Garage
Door
Door
Bracket
Curved
Door Arm
Straight
Door
Arm
T-Rail
Emergency
Release
Rope & Handle
You may find it helpful to refer back to this page
as you proceed with the installation of your
5
Opener Carton Inventory
Your garage door opener is packaged in two cartons which contain all parts illustrated below. If anything is
missing, carefully check the packing material. Parts may be "stuck" in the foam. Hardware for assembly and
installation is shown on page 7.
Security✚
Three-Function Remote Control
with Visor Clip (2)
Cable
Pulley Bracket
Standard Control Console
Trolley
2-Conductor
Bell Wire
White & White/Red
T-Rail
Center Section
Y
NL
TO
G
N
OU
M
ILIN
CE
UP
Header Bracket
RAGE
TO GA
DOOR
T-Rail
End Sections
Light Lens
Door Bracket
Sprocket Cover
"C" Wrap (2)
Chain and Cable
in Dispensing Carton
Safety Reversing Sensor
Mounting Bracket
With Square Holes (2)
Safety Reversing Sensor
Mounting Bracket
With Slot (2)
Hanging Brackets
(2) Safety Reversing Sensors
(1 Sending Eye and 1 Receiving Eye)
with
2-Conductor White & White/Black Bell Wire
attached
6
Safety Labels
and
Literature
Curved Door
Arm Section
Straight Door
Arm Section
Group all hardware found in all packages contained in the rail and opener cartons into
the three kits illustrated below.
Assembly Hardware Kit 41A3534
Hex Screw
5/16"-18x7/8" (3)
Washered Screw
5/16"-18x1/2" (2)
(mounted in opener)
Nut
5/16"-18 (5)
Carriage Bolts
1/4"-20x1/2" (4)
Master Link (2)
Lock Nut
1/4"-20x7/16" (4)
Lock Washer
5/16" (4)
Trolley
Threaded Shaft (1)
Installation Hardware Kit 41A3475-4
ASE
GRE
RAIL . 83A4
NO
Lag Screw
5/16"-9x1-5/8" (2)
Lag Screw
5/16"-18x1-7/8" (2)
NOTIC
E
Hex Screw
5/16"-18x7/8" (4)
Rail Grease
Handle
Ring
Fastener (3)
Lock Washer 5/16" (6)
Nut 5/16"-18 (6)
Rope
Screw
6ABx1" (2)
Carriage Bolt
5/16"-18x2-1/2" (2)
Clevis Pin
5/16"x2-3/4" (1)
Dry Wall Anchors (2)
Clevis Pin
5/16"x1-1/4" (1)
Clevis Pin
5/16"x1" (1)
Insulated
Staples (10)
Safety Reversing Sensor
Installation Hardware Kit 41A4116
Lag Screw
1/4x1-1/2" (4)
Hex Screw
1/4-20x1-1/2" (2)
Carriage Bolts
1/4"-20x1/2" (4)
Lock Nut
1/4"-20 (4)
Wing Nut (2)
Screw
#10-32x3/8" (4)
Lock Nut
#10x32 (4)
Insulated
Staples (20)
7
7
Assemble Tee Rail & attach Cable Pulley Bracket
Assembly
Section: Pages 8 – 11
SEARS '92 (525)
Assemble
Tee
Rail
Pulley
Bracket
To avoid installation difficulties,
do
not
run
the
garage
door
opener
until instructed to do so.
Assemble4/16/89
Tee Rail
&attach
attach
Cable
Bracket
- &6/27/89
-Cable
3/9/92
-Pulley
4/13/92
SEARS
SEARS'92
'92(525)
(525)
Make
sure
bolt necks are
4/16/89
6/27/89
3/9/92
- 4/13/92
4/16/89 - 6/27/89 - 3/9/92
- 4/13/92
Assembly Step 1
seated in the square
holes and rails are
aligned before you
tighten lock nuts. (See
right and wrong views).
Improper assembly can
cause jerky trolley
operation, noise and/or
nuisance door reversals.
Assemble the T-rail & Attach
the Cable Pulley Bracket
Hex Screws
5/16"-18x7/8"
• Align the 3 T-rail sections on a flat surface exactly
Hex
Screws
Hex
Screws
as shown. The end sections
are identical. Make
5/16"-18x7/8"
5/16"-18x7/8"
sure
the
"arrow
label"
on
the
center section is d
Cable Pulley
ne
pointing
lig
Brackettoward the door.
eA
B
st
• Insert the carriage bolts so the square
Mubolt necks
d
Cable
Pulley
ail
Cable
Pulley
r
ne ned
seat
in the square holes in the T-rail
endligsections
T
Bracket
ig
&
l
Bracket
A
t
e
e e A center
and pass through the roundraholes
int BT-rail
ck
B
us ust
B
l
M
i
M
l
section. Assemble lock Rnuts,
ensure
alignment
and
a
i il
a
r
a
T- T-r
&
tighten.
&
et et
1/4'' Lock Nut
1/4''
Lock
NutNut
1/4''
Lock
Lock
Washer
Lock
Washer
5/16"
5/16"
Wrong
T-RAIL BACK
(TO OPENER)
k k
racrac
B
il B lNut
Ra Rai5/16"
Lock Washer
5/16"
Right
NutNut
5/16"
5/16"
T-RAIL BACK
T-rail T-RAIL BACK
(TO OPENER)
(End Section)(TO OPENER)
T-rail
T-rail
(End
Section)
(End
Section)
Brace
If T-rail is not assembled
EXACTLY as shown,
trolley will not travel
smoothly along length of
rail or it will hit against
the nuts.
T-rail
Brace
(Center Section)
Brace
Carriage Bolt
1/4"-20x1/2"
Assemble
Tee Rail & attach Ca
SEARS '92 (52
Carriage
Bolt
Carriage
Bolt
1/4"-20x1/2"
1/4"-20x1/2" 4/16/89 - 6/27/89 - 3/9/9
T-rail
T-rail
(Center
Section)
(Center
Section)
TO
G
TO ARAG
GA E D
RAG OO
ED R
OO
R
TO
GA
RAG
ED
OO
Brace
Brace
R
Brace
T-rail
(End Section)
T-rail
T-rail
Section)
(End
Section)
Cable pulley(End
bracket
attaches to FRONT
END of T-rail
Hex Screws
5/16"-18x7/8"
Cable Pulley
Bracket
Square Carriage
Bolt Holes
d
ne
lig
t
us
A
Be
lM
Cable
pulley
bracket
Cable
pulley
bracket
attaches
to FRONT
attaches
to FRONT
END
of
T-rail
END of T-rail
Square
Carriage
Square
Carriage
Bolt
Holes
Bolt
Holes
t&
ke
ac
r
il B
ai
T-r
Ra
T-RAIL FRONT
(TO DOOR)
Lock Washer
5/16"
T-RAIL
FRONT
T-RAIL
FRONT
(TO
DOOR)
(TO
DOOR)
Nut
5/16"
• Position the cable pulley bracket on the front end of the
T-rail as shown. Fasten securely with the hardware.
Hardware Shown Actual Size
T-rail
(Center Section)
Hex Screw
5/16" - 18 x 7/8"
Nut
5/16" - 18
Lockwasher
5/16"
8
Cable pulley bracket
attaches to FRONT
END of T-rail
RAG
ED
OO
R
Brace
GA
When tightening
the screws, be
sure to keep
bracket parallel
to the rail.
Otherwise, the
Right
rail may bow
when opener is T-rail
Right
Right
operated.
(End Section)
Right
Carriage Bolts
1/4" - 20 x 1/2"
TO
Lock Nut
1/4" - 20 x 7/16"
Wrong
Wrong
Wrong
Wrong
Square Carriage
Bolt Holes
Brac
The Chamberlain Group, Inc.
Step 2 Install Trolley & Attach Chain Retainer Bracket
The Sears
Chamberlain
Group, Inc.
Hardware Shown
ChassisStep
Assembly
2
Actual Size
Step4/12/92
2 Install Trolley & Attach Chain Retainer Bracket
Install the Trolley on the T-rail
Sears Chassis
4/12/92
• Attach the threaded shaft to the trolley with the
lock washer and nuts as shown.
Lock Washer
5/16"
Trolley
Nut
5/16"-18
Rondelle-frein
de 5/16 de po
Éc
5/16
Trolley
Lock Washer
5/16"
Outer Nut
5/16"
Lock Washer
Trolley
Threaded Shaft
5/16"
Inner Nut
Trolley
5/16"
Threaded Shaft
Outer Nut
Trolley 5/16"
Inner Nut
5/16"
TO
GA
R
AG
E
DO
OR
Trolley
• As a temporary stop, insert a screwdriver into the
hole in the front end of the T-rail.
• Slide the trolley assembly along the rail to the
screwdriver stop.
Hex Screw
Lock Washer
Nut
If5/16"-18x7/8"
trolley hits against
any nuts
on the T-rail, the
5/16"
5/16"-18
bolts and nuts were attached from the wrong
side and must be repositioned. Review Step 1.
GA
RA
GE
DO
OR
Temporary Stop
Screwdriver
TO
Assembly Step 3
To fasten rail, use only those screws mounted
in the top of the opener. Any other screws will
cause serious damage to the opener.
• Place the opener on packing material to protect
the cover. For convenience, put a support under
the cable pulley bracket.
• Remove the (2) 5/16"-18x1/2" washered screws
Lock top
Washer
mounted in the
of the opener.
Nut
5/16"
5/16"-18
• Align the holes in the back section of the T-rail with
the holes in the opener.
• Fasten the rail with the (2) washered screws
previously removed. Tighten securely.
Remember to use only these screws! Any other
screws will cause serious damage to the opener.
• Insert a 5/16"-18x7/8" hex screw into the cover
protection bolt hole in the T-rail as shown. Tighten
securely with a 5/16" lock washer and nut.
NOTE: This screw prevents trolley over-travel.
Keep a 2" minimum between the trolley and this
screw when adjusting travel limits (see page 28).
Washered Screw
5/16"-18x1/2"
Hex Screw
Rondelle-frein
Écrou de Screw
Washered
5/16"-18x7/8"
de 5/16 de po
5/165/16"-18x1/2"
de po-18
Cover
Protection
Hex Screw
Bolt Hole
5/16"-18x7/8"
Cover
Protection
T-rail
BoltSection)
Hole
(Back
Use Only This
Type and Size
Screw
Use Only This
Type and Size
Screw
AVERTISSEMENT
Lock Washer
T-rail
5/16"
(Back Section)
Nut
Lock Washer
5/16"-18
5/16"
Nut
5/16"-18
Hardware Shown Actual Size
Nut
5/16"-18
Vis à tête hexag
de 5/16 de po-18x7
CAUTION
Fasten the T-rail to the Opener
Hex Screw
5/16"-18x7/8"
W
WARNING
Temporary Stop
Screwdriver
ATTENTION
Vis à tête hexagonale
de 5/16 de po-18x7/8 de po
Lock Washer
5/16"
9
Écrou de
5/16 de po-18
Rondelle-frein
de 5/16 de po
s
ng
Assembly
The
ChamberlainStep
Group,4Inc.
WARNING
Install
the Chain/Cable
& - Sears Chassis
Step
4 Install
Chain & Cable
Group, Inc.
Serious injury can result if
fingers become
AttachThe
theChamberlain
Sprocket Cover
Opener
4/10/92
Sprocket
entangled
in
moving
opener
sprocket.
Attach
Step 4 Install Chain & Cable - Sears Chassis
sprocket cover securely. Never operate opener
Opener
4/10/92 Dispensing
Carton
while your hand is near the opener sprocket.
The Chamberlain
Group,
Inc.
Sprocket
Step 4 Install Chain &Opener
Cable - Sears Chassis
Sprocket
Dispensing Carton
Opener
4/10/92
Leave Chain and Cable
Inside Dispensing
Carton to Prevent Kinking.
Dispensing Carton
Leave Chain and Cable
Inside Dispensing
Carton to Prevent Kinking.
CAUTION
Sprocket
Leave Chain and Cable
Inside Dispensing
Carton to Prevent Kinking.
Keep Chain and Cable
Taut When Dispensing
Keep Chain and Cable
• Detach the cable
loop
from
the carton and fasten it
Taut
When
Dispensing
to the trolley with a master link from the hardware
bag. See master link procedure, Figure 1.
Keep Chain and Cable
Whenagainst
Dispensing
• With theTaut
trolley
the screwdriver, dispense
the cable around the pulley.
Master Link back around the opener sprocket,
• Proceed
Master Link
Clip-On Spring
Figure 2. Be sure sprocket teeth engage Clip-On
the chain.
Spring
Continue forward to the trolley threaded shaft,
Master
Master Link
Master
Figure
3.
Link Cap
Link Cap Clip-On Spring
•Flat
Use
the second master link to connect the
End
of chain
Trolley to the flat end of the shaft. Check
Master
Master LinkLink Cap
Threaded
Shaft sure the chain is not
to make
Clip-On Spring
Cable
twisted.
Chain
Loop
Master
• Remove the screwdriver.
Master Link
Clip-On Spring
Figure 3
AVERTISSEMENT
Master Master Link
Link Cap Clip-On Spring
Flat End
Master
of Trolley
Master Link
Link Cap
Threaded
ShaftSpring
Clip-On
Flat End
of Trolley
Master
Threaded
Shaft
Link
Cap
T-rail
Flat End
of Trolley
Threaded Shaft
ATTENTION
Pin Notch
Pin
Cable
Loop
Pin Notch
Pin
Pin Notch
Trolley
Master
Link Bar
Trolley
Cable
Pulley
Install Chain and Cable
In This Direction
Pin
Master
Trolley
Link Bar
Cable
Pulley
Install Chain and Cable
In This Direction
Figure 1
Master
Link Bar
Cable
Pulley
Sprocket
Master Link Procedure:
Cover
Push pins of master link bar Back Tab Slot
through cable loop and hole inSprocket
Top of Opener
front end of trolley. Push cap Cover
Back Tab Slot
over pins and past notches.
Slide clip-on spring over
cap
Sprocket
Top of Opener
and into notches untilCover
both
pins
are
securely
locked.
Front Tab Slot
Install ChainSprocket
and Cable
In This Direction
Cover
Back Tab Slot
Top of Opener
Mounting
Plate
Front Tab
Slot
sprocket
cover:
Front Tab Slot
Chain
T-rail
Pin Notch
Trolley
Pin
Master
Link Bar
Chain
T-rail
Link Cap
Cable
Loop
T-rail
Chain
Back Tab Slot
Top of Opener
To attach the
Mounting
Plate
• Insert the back tab in the opener slot.
Squeeze the
cover slightly and insert the front tab in the slot on
Front Tab Slot
Mounting
the mounting plate.
Mounting
Plate
Plate
10
W
Assembly Step 5
Patin du rail
Tighten the Chain & Cable
• Spin the inner nut and lock washer down the
threaded shaft, away from the trolley.
• To tighten the chain, turn outer nut in the direction
shown. As you turn the nut, keep the chain
from twisting.
• When the chain is approximately 1/2" above the
base of the T-rail at its midpoint, re-tighten the
inner nut to secure the adjustment.
Sprocket noise can result if chain is either too
loose or too tight.
When installation is complete, you may notice some
chain droop with the door closed. This is normal. If
the chain returns to the position shown when the
door is open, do not re-adjust the chain.
Outer Nut
Lock
Washer
Inner Nut
To Tighten Outer Nut
To Tighten
Inner Nut
Trolley
Chain
1/2"
NOTE: During future maintenance, ALWAYS
pull the emergency release handle to disconnect
trolley before adjusting chain.
Base of T-rail
You have now finished assembling your garage door opener. Please read the following
warnings before proceeding to the installation section:
IMPORTANT INSTALLATION INSTRUCTIONS
WARNING
WARNING
WARNING
WARNING
To reduce the risk of severe injury or death to persons:
1.
READ AND FOLLOW ALL INSTALLATION INSTRUCTIONS.
2. Install only on a properly balanced and lubricated garage door. An improperly balanced door
may not reverse and could result in severe injury or death. Repairs to cables, spring assemblies
and other hardware must be made by a professional service person before installing opener.
CAUTIONCAUTION
3. Disable all locks and remove all ropes connected to the garage door before installing the opener.
Ropes connected to a garage door can cause entanglement and death.
WARNING
WARNING
4. If possible, install door opener 7 feet or more above floor with the emergency release handle
mounted 6 feet above the floor.
5. Do not connect the opener to power source until instructed to do so.
6. Locate the Door Control within sight of the door at a minimum height of 5 feet where small
children cannot reach and away from all moving parts of the door.
7. Install the User Safety Instruction Label on the wall adjacent to the door control and the
Maintenance Instruction Label in a prominent location on the inside of the garage door.
8. Upon completion of the installation, the door must reverse when it comes in contact with a
one-inch high object or a 2x4 laid flat on the floor.
AVERTISSEMENT
AVERTISSEMENT
AVERTISSEMENT
AVERTISSEMENT
9. Do not wear watches, rings or loose clothing while installing or servicing an opener. Jewelry or
loose clothing can be caught in the mechanism of the garage door or the opener.
11
AVERTISSEMENT
AVERTISSEMENT
Installation Section: Pages 12 – 27
TheGroup,
Chamberlain
Group, Inc.
The Chamberlain
Inc.
Position
SECTIONAL
PositionGroup,
Header
Bracket
SECTIONAL
DOOR AND DOOR AN
Installation
Step
1 Header Bracket
The Chamberlain
Inc.
W
WARNING
Sectional
and
One-Piece
Track
Installations
Sectional
and One-Piece
Track Installations SECTIONAL
ONE-PIECE
WITH TR
ONE-PIECE
DOOR
TRACK
Position
Header
Bracket
Determine
Header
Bracket Location
DOOR
ANDWITHDOOR
1/30/92
- 4/6/92to
1/30/92
- 4/6/92Track
If the header bracket is not rigidly fastened to
Sectional
and
One-Piece
Installations
Installation
procedures
vary according
ONE-PIECE DOOR WITH TRACK
garage
door types. Follow the instructions
1/30/92
- 4/6/92
which apply to your door.
SECTIONAL Door and
ONE-PIECE Door With Track
Header
Wall
Header
Wall
Header
Vertical Wall
Guideline
a structural support on the header wall or
ceiling, the safety reverse system may not
work properly (see page 30). The door might
not reverse when required, and could cause
serious injury or death.
The garage door springs, cables, pulleys,
brackets and their hardware are under extreme
tension. Do not attempt to loosen, move or
Finished Serious personal injury
Finished
adjust
Vertical them yourself.
Ceiling
Ceiling
or
death could result. Call for professional
Guideline
garage door service.
2x4
CAUTION
Vertical
Guideline
Finished
Ceiling
2x4
2x4
Structural
Supports
Structural
Supports
• Close the door and mark the inside
vertical centerline of the garage door.
• Extend the line onto the header wall
above the door.
Remember, you can fasten the
header bracket within 2 feet of the
Verticalleft or right of the door center only if
Guideline
a torsion spring or center bearing
plate is in the way; or you can attach
it to the ceiling (refer to page 14)
when clearance is minimal. (It may
be mounted on the wall upside down
if necessary, to gain approximately
1/2".)
If you need to install the header bracket
on a 2x4 (on wall or ceiling), use lag
screws (not supplied) to securely fasten
the 2x4 to structural supports as shown
here and on page 13.
Structural
Supports
Vertical
Guideline
AVERTISSEMENT
Vertical
Guideline
ATTENTION
Ceiling
Ceiling
Ceiling
• Open your door to the highest
Header
point of travel as shown.Wall
Draw
an intersecting horizontal2"line
on the header wall 2" above
Highestwill
Point
the high point. This height
Travel
provide travel clearanceof for
the
top edge of the door.Door
Door clearance brackets are
availableDoor
for sectional doors
when headroom clearance is
less than 2". See accessory
page 38.
Header
Wall
2"
Track
Highest Point
of Travel
Track
Header
Wall
2"
Header
Wall
2"
Highest Point
of Travel
Track
Header
Wall
2"
T
Track
Door Highest Point
of Travel
Door
Highest Point
of Travel
Door
Highest Po
of Travel
Door
SECTIONAL
DOOR CURVED
TRACK
SECTIONAL DOOR CURVED
TRACKSectional
door
SECTIONAL DOOR CURVED TRACK
Proceed
to Step 2, page 14.
Header
Wall
2"
Track
with curved track
WITH HORIZONTAL T
ONE-PIECE One-piece
DOOR WITHONE-PIECE
HORIZONTAL
TRACK
door DOOR
& JAMB HARDWARE
& JAMB HARDWARE
with horizontal track
ONE-PIECE DOOR WITH HORIZONTAL TRACK
& JAMB HARDWARE
12
One Piece Door Without Track
1/30/92 - 4/7/92
Header
Wall
Header
Wall
Unfinished
Unfinished
Ceiling
Ceiling
Vertical
Vertical
Centerline
Centerline
ONE-PIECE Door Without
2x4
2x4 Track
Structural
Structural
supports
supports
Read the Safety instructions on page 12. They also apply to doors without tracks.
Unfinished
Ceiling
Header Wall
• Close the door and mark the
inside vertical centerline of
your garage door. Extend
the line onto the header wall
above door.
If headroom clearance is
minimal, you can install the
header bracket on the
ceiling. See page 14.
• If you need to install the
header bracket on a 2x4 (on
wall or ceiling), use lag
screws (not supplied) to
securely fasten the 2x4 to
structural supports as
shown.
Vertical
Centerline
2x4
2x4
Vertical
2x4
Vertical
Centerline
ofof
Centerline
Garage
Door
Garage
Door
Structural
supports
OPTIONAL
CEILING
MOUNT
OPTIONAL
CEILING
MOUNT
FOR
HEADER
BRACKET
FOR
HEADER
BRACKET
2x4
Vertical
Centerline of
Garage Door
OPTIONAL CEILING MOUNT
FOR HEADER BRACKET
Header
Wall
Header
Wall
Point
Header
Highest
Point
Header Highest
ofof
Travel
Wall
Travel
Wall
Highest
Point
Highest
Point
ofof
Travel
Travel
Door
Door
Header Wall
Jamb
Jamb
Hardware
Hardware
Distance
Distance
Highest Point
of Travel
Header
Wall
Distance
Distance
Door
Door
Highest Point
of Travel
Pivot
Pivot
Jamb
Distance
Door
One-piece
Hardware door without track
jamb hardware
Distance
Door
One-piece door without track
pivot Pivot
hardware
• Open your door to the highest point of travel as
shown. Measure the distance from the top of the
door to the floor. Subtract the actual height of the
door. Add 8" to the remainder. (See Example).
• Close the door and draw an intersecting horizontal
line on the header wall at the determined height.
If the total number of inches exceeds the height
available in your garage, use the maximum
height possible, or refer to page 14 for ceiling
installation.
EXAMPLE
Distance from top of door
(at highest point of travel) to floor...........................92"
Actual height of door .............................................-88"
Remainder................................................................4"
Add .........................................................................+8"
Bracket height on header wall..............................=12"
(Measure UP from top of CLOSED door.)
Proceed to Step 2, page 14.
13
You can attach the header bracket either to the
wall above the garage door, or to the ceiling.
Follow the instructions which will work best for
your particular requirements.
Installation
Step 2
Mounting
New Header Bracket
Install
the Header
Bracket
10/16/91
- 10/26/91
- 4/5/92
Mounting Header Bracket to WALL
Mounting New Header Bracket
Fasten the Header Bracket to the Wall
Mounting
New
Header Bracket
10/16/91
- 10/26/91
- 4/5/92
• Center
the bracket- on
the vertical guideline with
• Mark either set of bracket holes (do not use the
10/16/91
- 10/26/91
4/5/92
the bottom edge of the bracket on the horizontal
holes
designated
for ceiling mount). Wall
Drill 3/16" pilot
Mounting
Header
Bracket
to WALL
Vertical
Mountingto
Holes
line as shown (with the arrow pointing
toward the
holes and fasten the bracket securely
a structural
Center
Mounting Header Bracket
to WALL
Header
ceiling).
support with the hardware provided.
Line
Y
NL
TO
Wall
UN
G
Lag Screws
5/16"x9x1-5/8"
MO
ILIN
CE
UP
Header
Bracket
2x4
Structural
Support
Header
Wall
Vertical
Center
VerticalLine
Center
Line
CEILING MOUNT ONLY
UP
Wall
Mounting Holes
Wall
Mounting Holes
Y
NL
TO
UN
G
ILIN
CE
Y
NL
Header
Wall
TO
UN
G
Header
Bracket
Header
Bracket
MO
UP
Door
Spring
MO
ILIN
CE
UP
Garage
Door
Vertical
Center
Line
Door
Spring
Door
Spring
CEILING MOUNT ONLY
UP
UP
Optional
Wall Mounting
Holes
The nail hole is for positioning
only. You must use lag screws to
The nailmount
hole isthe
for header
positioning
bracket.
Optional
only. You must use lag screws to
Wall Mounting
mount the header bracket.
OptionalHoles
Wall Mounting
Holes
Garage
Door
Garage
Door
Highest
Point of Travel
Highest
(of Garage Door)
Point of Travel
(of Garage Door)
CEILING MOUNT ONLY
only. You must use lag screws to
mount the header bracket.
2x4
Structural
2x4 Support
Structural
Support
Highest
Point of Travel
(of Garage Door)
Lag Screws
5/16"x9x1-5/8"
Lag Screws
5/16"x9x1-5/8"
The nail hole is for positioning
Hardware Shown Actual Size
Vertical
Center
VerticalLine
Center
Line
Lag Screw
5/16"-9x1-5/8"
Fasten the Header Bracket to the Ceiling
• Extend the vertical guideline onto the ceiling as
shown.
• Center the bracket on the vertical mark, no more
than 6" from the wall. Make sure the arrow is
pointing toward the wall. The bracket can be
mounted flush against the ceiling when clearance
is minimal.Ceiling Mounting Holes
• Mark holes designated for ceiling mount only. Drill
CEILINGand
MOUNTfasten
ONLY
3/16" pilot holes
bracket securely to a
structural support with the hardware provided.
Finished
Ceiling
Vertical
Tire-fond de
Center Line
5/16 de po-9x1-5/8 po
UP
6" Maximum
Door
Spring
Ceiling Mounting Holes
Vertical
Center Line
Vertical
Lag Screws
Center
Line
5/16"x9x1-5/8"
Header
Bracket
Header
6" Bracket
Maximum
Ceiling Mounting Holes
CEILING MOUNT ONLY
UP
UP
UP
CEILING MOUNT ONLY
The nail hole is for positioning only.
You must use lag screws to mount
UP
the header bracket.
Finished
Ceiling
Finished
Ceiling
Header
Bracket
6" Maximum
Door
Spring
UP
Door
Spring
Garage
Door
The nail hole is for positioning only.
You must use lag screws to mount
The nail hole isthe
forheader
positioning
only.
bracket.
You must use lag screws to mount
the header bracket.
Vertical
Center Line
Lag Screws
Header
5/16"x9x1-5/8"
Wall
Lag Screws
5/16"x9x1-5/8"
Header
Wall
14
Garage
Door
Garage
Door
Vertical
Center Line
Vertical
Center Line
Header
Wall
Attach Tee Rail to Header Bracket
2/4/92 - 4/9/92
Installation Step 3
Attach the T-rail to the Header Bracket
• Position the opener on the garage floor below the
header bracket. Use packing material as a
protective base.
If the door spring is in the way you'll need help.
Have someone hold the opener securely on a
temporary support to allow the T-rail to clear the
spring.
• Position the cable pulley bracket against the header
bracket.
• Align the bracket holes and join with a clevis pin as
shown.
• Insert a ring fastener to secure.
Header Wall
Header
Bracket
Cable
Pulley
Bracket
Ring Fastener
T-rail
Header Bracket
Clevis Pin
5/16"x2-3/4"
Cable
Pulley
Bracket
T-rail
Garage
Door
Temporary
Support
Hardware Shown Actual Size
Clevis Pin
5/16"x2-3/4"
Ring Fastener
15
Porte
Installation Step 4
CAUTION
Disconnect and Lockout
PositionManual
the Opener
Searsapply
-92 to your door
Follow instructions which
type as illustrated. 9/7/90, 3/2/92
Escabeau
To prevent damage to steel, aluminum,
fiberglass or glass panel doors, do not rest the
opener on the door without using a 2x4.
SECTIONAL Door & ONE-PIECE Door with Track
Step 2 Attach Tee Rail to Header Bracket - Sears 315-699 (Yellow Disk #2)
A 2x4 laid flat is convenient for setting an ideal
Models 53315, 53415, 53515, 53625 & 53699
door-to-T-rail distance.
6/20/89 - 6/27/89 - 11/6/89
T-rail
2x4
• Raise the opener onto a stepladder.
Trolley
You will
Trolleyneed help at this point if the ladder is
Release Arm
Arm
notRelease
tall enough.
Trolley
• Open the door all the way and place a 2x4 laid flat
Door
Emergency
on the top section beneath the T-rail.
Release Handle
IfNOTthe
top
panel
hits
the
trolley
when
you
raise
(Pull Down & Back
Rail
2x4 à plat
ICE
NOTICE
Towards
the door, pull down on the trolley release
armOpener)
to
Support de linteau
Dessus de l'ouvre-porte
disconnect the inner and outer sections. The
Stepladder
Dessus de la porte
trolley can remain disconnected until Step 12 is
completed.
AVERTISSEMENT
Trolley
Emergency
Release Handle
(Pull Down)
ATTENTION
Porte
Escabeau
Escabeau
Trolley
Release Arm
Trolley
ONE-PIECE Door without Track
T-rail
Header
Bracket
2x4
• With the door fully open and parallel to the floor,
measure the distance from the floor to the top of
the door.
• Using a Door
stepladder as a support, raise the opener
to the same distance as the door from the floor (it
will be at a slight angle as shown).
• The top of the door should be level with the top of
Stepladder
the opener. Do not position
the opener more than
2" above this point.
Top of Opener
Top of Door
Stepladder
16
Solives
Installation Step 5
WARNING
Hang the Opener
The opener could fall and injure someone if it
is not properly secured. Fasten the opener
securely to structural supports of the garage.
Tire-fond de
5/16 de po-18 x 1-7/8
de po
Solives
Mesurer
la distance
Tire-fond de
Two representative installations
are
shown.
5/16 de
po-18
x 1-7/8 de po
Yours
may
be
different.
Hanging
brackets
should
Mesurer
la distanceFigure 1, to provide rigid support. On
be angled,
Vis de 5/16 de po-18x7/8 de po,
finished
ceilings, Figure 2, attach a sturdy metal
rondelle-frein de 5/16 de po,
bracket to
structural
before installing the
écrou
de 5/16 desupports
po-18
opener. The bracket and fastening hardware are not
supplied.
Vis de
5/16
de po-18x7/8
de po,
• Measure
the
distance
from
each side of the opener
rondelle-frein de 5/16 de po,
to
the
structural
support.
écrou
de 5/16 de po-18
he Chamberlain Group,
Inc.
• Cut both pieces of the hanging bracket to required
lengths.
ftmaster Combination
• Drill 3/16" pilot holes in the structural supports.
23/92
• Attach
one end of each bracket to a support with
Poutrelle
cachée
5/16"-18x1-7/8"
lag screws.
— Plafond fini —
• Fasten the openerTire-fond
to the de
hanging brackets with
5/16
de
po-18
x
1-7/8
de po
5/16"-18x7/8" screws, lock washers
and nuts.
• Check
to make sure the T-rail is centered over the
Poutrelle
door cachée
(or in line with the header Vis
bracket
if the
de 5/16 de po-18x7/8 de po,
—the
Plafond
fini — de 5/16 de po,
rondelle-frein
bracket is not centered
above
door).
Tire-fond de
écrou de 5/16 de po-18
5/16Operate
de po-18 x 1-7/8
de po manually.
• Remove
the
2x4.
the door
If the
(non fournis)
Cornière
(non fournie)
door
hits the rail, raise the header bracket.
Vis de 5/16 de po-18x7/8 de po,
rondelle-frein de 5/16 de po,
écrou de 5/16 de po-18
(non fournis)
Cornière
Grease
the top and underside of the
(non fournie)
E
rail surface where the trolley
AS
RE
IL G 3A4
Vis
de
5/16
de
po-18x7/8
de
po,
RA
8
.
O
slides with rail grease.
N
Structural
Supports
CAUTION
Figure 1
Lag Screws
Structural
5/16"-18x1-7/8"
Supports
Measure
Distance
Lag Screws
5/16"-18x1-7/8"
Measure
Distance
5/16"-18x7/8" Screw
5/16" Lock Washer
5/16"-18 Nut
5/16"-18x7/8" Screw
5/16" Lock Washer
5/16"-18 Nut
AVERTISSEMENT
Figure 2
Hidden
Support
ATTENTION
— FINISHED CEILING —
Lag Screws
5/16"-18x1-7/8"
rondelle-frein de 5/16 de po,
écrou de 5/16 de po-18
Hidden
Support
Vis de 5/16 de po-18x7/8 de po,
rondelle-frein de 5/16 de po,
écrou de 5/16 de po-18
Rail Grease
Bracket
(Not Supplied)
Hardware Shown Actual Size
Bracket
(Not Supplied)
5/16"-18x7/8" Screw
5/16" Lock Washer
5/16"-18 Nut
Lag Screw
5/16"-18x1-7/8"
Hex Screw
5/16"-18x7/8"
5/16"-18x7/8" Screw
5/16" Lock Washer
5/16"-18 Nut
Nut 5/16"-18
Lock Washer 5/16"
17
Tire-fond de 5/16 de po-18 x 1-7/8 de po
(Not Supplied)
5/16"-18x7/8" Screw
— FINISHED CEILING —
5/16" Lock Washer
Lag Screws
5/16"-18 Nut
5/16"-18x1-7/8"
(Not Supplied)
5/16"-18x7/8" Screw
5/16" Lock Washer
5/16"-18 Nut
CAUTION
Installation Step 6
WARNING
Install the Door Control
Do not connect to live electrical wiring. Connect
only to 24 Volt low voltage wires. Connection to
live wires or higher voltage may cause serious
injury from shock, burn or electrocution.
Children operating or playing with a garage
door opener can injure themselves or others.
The garage door could close and cause
serious injury or death.
Install the door control (or any additional push
buttons) out of the reach of children and away
from all moving parts of the door and door
hardware, but where the garage door is visible.
Do not allow children to operate the push
button(s) or the remote control(s).
A moving garage door could injure someone
under it. Activate the opener only when the
door is properly adjusted, you can see it
clearly, and there are no obstructions to door
travel.
Locate the door control within sight of the door
at a minimum height of 5 feet where small
children cannot reach, and away from all moving
parts of the door and door hardware.
The door control is typically attached directly to the
wall. If installing into drywall, drill 5/32" holes and use
the anchors provided. For pre-wired installations (as
in new home construction), Console models may be
mounted to a standard single gang box (Figure 2).
1. Strip 1/4" of insulation from one end of the bell
wire and connect it to the two screw terminals on
the back of the door control: white to 2, and
white/red to 1.
2. Pry off cover along one side with a screwdriver
blade (see Figure 1). Fasten with 6ABx1-1/4” selftapping screws (standard installation) or 6-32x1"
machine screws (pre-wired installation) as follows:
• Install bottom screw, allowing 1/8"
to protrude
Hardware Shown Actual Size
The
Chamberlain Group, Inc.
above wall surface.
Std Console Door Control
• Position bottom of door control on screw head and
slide down to secure. Adjust screw8/95
for snug fit.
Insulated
6AB x 1-1/4" Screw
Staples
Control Console (std installation)
• Drill and install top screw with care to avoid
cracking plastic housing. Do not overtighten.
6-32 x 1" Screw
• Insert top tabs and snap on cover.
Control Console (pre-wired)
Dry Wall Anchors
3. (For standard installation only) Run the bell wire
up the wall and across the ceiling to the opener.
Use insulated staples to secure the wire in several
Figure 1
Figure 2
places. Be careful not to pierce the wire with a
REMOVE
&
REPLACE
COVER
PRE-WIRED
staple, creating a short.
INSTALLATION
To Replace,
To Remove,
4. Connect the bell wire to the terminal screws on the
Insert
Twist
Top Tabs
Here
opener panel: white to 2; white/red to 1.
First
Sears
5. Position the antenna wire as shown.
AVERTISSEMENT
AVERTISSEMENT
AVERTISSEMENT
ATTENTION
DoorContrls/RearView
7/95
24 Volt
2-Conductor
Bell Wire
nt/back
2-Conductor
Bell Wire
Opener
Terminal Screws
Lighted
Push Button
Figure 1
Figure 2
POUR ENLEVER ET REMETTRE
LE COUVERCLE
Pour remettre,
insérer tout
d'abord
3
les pattes
supérieures
1
2
9
1
7
3
9
STANDARD CONTROL
(BACK VIEW)
Top
Mounting
Hole
INSTALLATION
PRÉ-CÂBLÉE
WHITE RED
1
2
Pour enlever,
dévisser à
cet endroit
1
7
3
5
5
KG
KG
Bell
Wire
Terminal
Screws
Bottom
Mounting
Hole
Fil de sonnerie
24 V à
2 Conducteurs
STANDARD
CONTROL
CONSOLE
Back Panel
of Opener
Antenna
18
Vis 6
Vis 6
(po
6. Attach the User Safety Instruction label to the wall
near the door control, and the Maintenance
Instruction label in a prominent location on the
inside of the garage door.
Do NOT connect the power and operate the
opener at this time. The trolley will travel to the
full open position but will not return to the
close position until the sensor beam is
connected and properly aligned.
See Safety Reversing Sensor instructions
beginning on page 21.
Page 32 explains how to use the door control.
Installation Step 7
The Chamberlain Group, Inc.
Step 7 Install Light and Lens - Sears
4/17/92 - 4/20/92
Install the Light and the Lens
Install the light:
• Install a 75 watt maximum light bulb in each
socket. The lights will turn ON and remain lit for
approximately 4-1/2 minutes when power is
connected. Then the lights will turn OFF.
• If the bulbs burn out prematurely due to vibration,
replace them with standard neck "Garage Door
Opener" bulbs.
Lens Guide
Light Lens
Install the lens:
Lens Slot
Step 5 Attach Emergency
Release Rope & H
Lens Tab
Models 53315, 53415, 53
75 Watt Max.
6/20/89 - 6
Light Bulb
• Apply slight pressure on the sides of each lens
and slide the tabs into the slots in the side panels.
• For convenience, the lens may be installed
after Adjustment Step 4 on page 30.
• Reverse the procedure to remove the lenses.
Installation Step 8
Guides
du diffuseur
Attach the Emergency
Release Rope and Handle
WARNING
use the red handle to pull Trolley
the door
open or closed. The rope knot could become
untied and you could fall. Use the emergency
release only to disengage the trolley
Encoche and, if
du diffuseur
possible, only when the door is closed.
diffuseuris open
Garage doors are heavy. IfPatte
thedudoor
when the handle is pulled, the door could
de 75
close inadvertently if it isAmpoules
not properly
watts maximum
balanced. Serious injury may result
to persons
under the door. Make sure the doorway is clear
of persons and obstructions before pulling
handle when door is open.
Diffuseur
Do not
• Thread one end of the rope through the hole in
the top of the red handle so "NOTICE" reads right
side up as shown. Secure with an overhand knot.
The knot should be at least 1" from the end of
the rope to prevent slipping.
• Thread the other end of the rope through the hole
in the release arm of the outer trolley.
• Adjust rope length so the handle is 6 feet above
the floor. Secure with an overhand knot .
If it is necessary to cut the rope, heat seal the
cut end with a match or lighter to prevent
unraveling.
CAUTION
Overhand
Knot
Trolley
Trolley
Release Arm
Rope
NOT
Overhand
Knot
ICE
Emergency
Release Handle
AVERTISSEMENT
19
Rope
NO
Overhand
Knot
Installation Step 9
Electrical Requirements
To prevent electrocution or fire , installation
and wiring must be in compliance with local
electrical and building codes.
Do NOT use an extension cord, 2-wire adapter,
or change the plug in any way to make it fit
your outlet.
To reduce the risk of electric shock, your garage
door opener has a grounding type plug with a third
grounding pin. This plug will only fit into a grounding
type outlet.
If the plug doesn't fit into the outlet you have,
contact a qualified electrician to install the proper
outlet.
CAUTION
WARNING
To avoid installation difficulties,
do not run the opener at this time.
Ground Tab
Green Ground
Screw
Right
RIGHT
AVERTISSEMENT
Ground Wire
WRONG
Wrong
AVERTISSEMENT
If permanent wiring is required by your local code, refer to the following procedure:
AVERTISSEMENT
WARNING
ARNING
UTION
WARNING
WARNING
To prevent electrocution, remove power from
the garage door opener and from the circuit
you plan to use for the permanent connection.
ATTENTION
Permanent wiring
connection
To make a permanent connection through the
7/8" diameter hole in the top of the opener
(according to local code):
• Remove the opener cover screws and set the
cover aside.
• Remove the attached 3-prong cord.
• Connect the black (line) wire to the screw on the
brass terminal; the white (neutral) wire to the
screw on the
silver terminal; and theWRONG
ground wire
RIGHT
to the green ground screw. The opener must be
grounded.
• Reinstall the cover.
Vis verte
de terre
Ground Tab
WARNING
TISSEMENT
TENTION
Patte d
Green Ground
Screw
Ground Wire
AVERTISSEMENT
Fil de terr
Mauvais
Bon
Black
Wire
White Wire
Black
Wire
To avoid installation difficulties,
do not run the opener at this time.
AVERTISSEMENT
20
Branchement
électrique
permanent
The Safety Reversing System
Information you'll need before you begin the installation of the safety reversing sensor.
The safety reversing sensor must be connected
and aligned correctly before the garage door
opener will move in the down direction. This is a
required safety device and cannot be disabled.
WARNING
Without a properly working safety reversing
sensor, persons (particularly children) could
be injured or killed by a closing garage door.
Read and follow all instructions.
To protect small children, install the safety
reversing sensor so that the beam will be no
higher than 4"-6" above the garage floor.
Disconnect power to the garage door opener
before installing the safety reversing sensor.
Installation procedures are the same for sectional
and one-piece doors.
CAUTION
The brackets must be securely fastened to a solid
surface such as the studs on either side of the door,
or add a piece of wood at each location if installing in
masonry construction.
Be sure power to the opener is disconnected.
The sending eye transmits an invisible light beam to
the receiving eye. The units can be installed on
either side of the garage door as long as the sun
never shines directly into the receiving eye lens.
Look at the label
on the connector
end of each case
The Chamberlain
Group,
Inc.
to identify the sensors.
Safety Sensor
The brackets must be connected and fastened so
Instruction
Page
1
that theSheet
sending
and receiving
eyes face each other
as shown
in Figure
Protector
System
Disk1.#1 (Yellow)
If an- obstruction
11/5/91
1/15/92 breaks the light beam while the
garage door is closing, the door will stop and
reverse to full open position and the opener lights
will flash for 5 seconds.
The invisible light beam path must be unobstructed.
No part of the garage door (or door tracks, springs,
hinges, rollers or other hardware) can interrupt the
beam while the door is closing. If it does, use a piece
of wood to build out each sensor mounting location to
the minimum depth required for light beam clearance.
AVERTISSEMENT
ATTENTION
Sensor Beam
4-6" max.
above floor
Sensor Beam
4-6" max.
above floor
Invisible Light Beam
Protection Area
Figure 1: Facing the door from inside the garage
21
Installation Step 10
Install the Safety Reversing Sensor
Figure 2
Figures 2 and 3 show assembly of brackets and
"C" wrap based on the recommended installation of
the sensors as shown on page 21.
However, Figures 4 and 5 are variations which may
fit your installation requirements better. Make sure
the wraps and brackets are aligned so the
sensors will face each other across the garage
door.
• Fasten the "C" wraps to the mounting brackets
having square holes, using the hardware shown
in Figure 2.
• Connect each assembly to a slotted bracket, using
the hardware shown in Figure 3.
Note the alignment of the brackets for left and
right sides of the door.
• Finger tighten the lock nuts.
• Use bracket mounting holes as a template to
locate and drill (2) 3/16" diameter pilot holes on
both sides of the garage door, 4"-6" above the
floor but not exceeding 6". (See warning on
page 21.)
• Attach bracket assemblies with 1/4"x1-1/2" lag
screws as shown in Figure 3.
• Adjust right and left side bracket assemblies to the
same distance out from the mounting surface.
Make sure all door hardware obstructions are
cleared. Tighten the nuts securely.
Mounting Bracket
With Square Holes
"C" Wrap
#10-32
Lock Nuts
#10-32x3/8"
Screws
Figure 3
1/4x1-1/2"
Lag Screws
1/4-20x1/2" Carriage Bolts
(with square shoulder)
Inside
Garage
Wall
Mounting Bracket
with Slot
Mounting Bracket
with Square Holes
1/4"-20
Lock Nuts
"C" Wrap
Hardware Shown Actual Size
#10x32
Lock Nut
#10-32x3/8"
Screw
1/4x1-1/2"
Lag Screw
1/4"-20x1/2"
Carriage Bolts
Staples
1/4"-20
Lock Nut
Figure 5
Figure 4
Alternate Wall Mount
Alternate Floor Mount
Inside
Garage
Wall
Vis n o 1032x3/8 de po
Inside
Garage
Wall
Mounting
Bracket
Écrou
n o 10x32
with Slot
Tire-fond de 1/4x1-1/2 po
Agrafes
Mounting Bracket
with Square Holes
Indicator Light
Écrou
Boulons à tête bombée
Mounting
et collet carré
de Bracket 1/4 de po-20
with Square
1/4 de po-20x1/2
po Holes
Mounting Bracket
with Slot
"C" Wrap
Sensor
with wire
Garage
Floor
Sensor with wire
"C" Wrap
Indicator Light
Garage
Floor
22
Attach with
concrete anchors
(not provided)
• Center each sensor unit in a "C" wrap with lenses
pointing toward each other across the door (see
Figure 6).
• Secure sensors with the hardware shown. Finger
tighten the wing nut on the receiving eye to allow
for final adjustment. Securely tighten the sending
eye wing nut.
• Run the wires from both sensors to the opener.
Use insulated staples to secure wire to wall and
ceiling.
• Strip 1/4" of insulation from each set of wires.
Separate white and white/black wires sufficiently to
connect to the opener terminal screws: white to 2
and white/black to 3.
Figure 6
Wing
Nut
"C" Wrap
Indicator
Light
Sensor
with Wire
1/4-20 x 1-1/2"
Hex Bolt
Trouble Shooting
1. If the sending eye indicator light does not glow
steadily after installation, check for:
• Electric power to the opener.
• A short in the white or white/black wires. These
can occur under staples or at screw terminal
Aligning the Safety Sensors
connections.
• Plug in the opener. Green indicator lights in both
•
Incorrect wiring between sensors and opener.
the sending and receiving eyes will glow steadily if
•
An
open wire (wire break).
wiring connections and alignment are correct.
2. If the sending eye indicator light glows steadily but
The sending eye indicator light will glow regardless
the receiving eye indicator light doesn't:
of alignment or obstruction. If the indicator light is
• Check alignment.
off, dim, or flickering in the receiving eye (and the
• Check for an open wire to the receiving eye.
invisible
light
beam
path
is
not
obstructed),
Attaching Sensor to "C" Wrap and Wires to Operator
3. If the receiving eye indicator light is dim, realign
alignment is required.
11/14/91
- 1/15/92
either sensor.
• Loosen the sending eye wing nut and re-adjust,
NOTE: When the invisible beam path is obstructed or
aiming directly at the receiving eye. Lock in place.
misaligned while the door is closing, the door will
• Loosen the receiving eye wing nut and adjust
reverse. If the door is already open, it will not close.
sensor vertically and/or horizontally until it receives
The
opener lights will flash 10 times. (If bulbs are not
the sender’s beam. When the green indicator light
installed,
10 clicks are audible.) See page 21.
glows steadily, tighten the wing nut.
Hardware Shown Actual Size
Figure 7
1/4-20x1-1/2"
Hex Bolt
Connect Wire to
Opener Terminals
Wing Nut
Finished
Ceiling
Bell Wire
Bell Wire
Vis à tête hexagonale
de 1/4-20x1-1/2 po
Écrou à oreilles
Sensor
Connections
Door Control
Connections
(dotted line)
1
2
3
OPENER TERMINAL SCREWS
Sensor
Invisible Light Beam
Protection Area
Sensor
23
Door
Bracket-Sectional
Installation
Step
6/96Fasten Door Bracket
11
CAUTION
To prevent damage to steel, aluminum,
fiberglass or glass panel doors, always
reinforce the inside of the door both vertically
and horizontally with an angle iron.
Follow instructions which apply to your door
type as illustrated below or on page 25.
A horizontal brace should be long enough to be secured to 2 vertical supports. A vertical brace should
cover the height of the top panel.
The illustration shows one piece of angle iron as the horizontal brace. For the vertical brace, 2 pieces of
angle iron are used to create a "U"-shaped support. The best solution is to check with your garage door
manufacturer for an opener installation door reinforcement kit.
SECTIONAL Door Installation Procedure
Header
Bracket
AVERTISSEMENT
Horizontal and vertical reinforcement
is needed for lightweight garage doors
(fiberglass, aluminum, steel,
doors with glass panel, etc).
Figure 1
Vertical
Reinforcement
Vertical
Guideline
Door
Bracket
Location
ATTENTION
UP
Carriage Bolt
5/16"-18x2-1/2"
Vertical
Guideline
Door
Bracket
Lock
Washer
5/16"
Nut
5/16"-18
Inside Edge
of Door or
Reinforcement Board
Figure 2
UP
• Center the door bracket on the previously marked
vertical guideline used for the header bracket
installation. Note correct UP placement, as
stamped inside the bracket.
• Position the bracket on the face of the door within
the following limits:
A) The top edge of the bracket 2"-4" below the top
edge of the door.
B) The top edge of the bracket directly below any
structural support across the top of the door.
• Mark and drill 5/16" left and right fastening holes.
Secure the bracket as shown in Figure 1 if there is
vertical reinforcement.
If your installation doesn't require vertical reinforcement but does need top and bottom fastening holes
for the door bracket, fasten as shown in Figure 2.
Door Bracket
Hardware Shown Actual Size
Nut 5/16"-18
Lock Washer 5/16"
Carriage Bolt
5/16"-18x2-1/2"
24
2/4/92 - 4/7/92
All ONE-PIECE Door Installation Procedure
Please read and comply with the warnings and reinforcement instructions on page 24.
They apply to one-piece doors also.
Header Wall
2x4 Support
Finished Ceiling
Horizontal and vertical
reinforcement is needed for
lightweight garage doors
(fiberglass, aluminum, steel,
door with glass panel, etc.).
Header
Bracket
Door
Bracket
Vertical
Centerline of
Garage Door
Inside Edge
of Door or
Reinforcement Board
Door
Bracket
• Center the bracket on the inside face of the door,
in line with the header bracket as shown. Mark
either the left and right, or the top and bottom
holes.
• Drill 5/16" pilot holes and fasten the door bracket
with hardware supplied.
Hardware Shown Actual Size
Nut 5/16"-18
Lock Washer 5/16"
Carriage Bolt
5/16"-18x2-1/2"
25
Écrou de
5/16 de po-18
Rondelle-frein
de 5/16 de po
Installation Step 12
Connect Door Arm to Trolley
Follow instructions which apply to your door
type as illustrated.
SECTIONAL Doors Only
Make sure garage door is fully closed. Pull the emergency release handle to disconnect the outer trolley
from the inner trolley. Slide the outer trolley back (away from the door) about 2" as shown in
Figures 1, 2 and 3.
Figure 1:
DoorArmTtoTrolleySec/FR
• Fasten
straight door arm section to outer trolley
New
door brkt
with
the
5/16"x1" clevis pin. Secure the connection
1/96
with a ring fastener.
• Fasten curved door arm to the door bracket in the
same way, using the 5/16"x1-1/4" clevis pin.
Figure 2:
• Bring arm sections together. Find two pairs of holes
that line up and join sections. Select holes as far
apart as possible to increase door arm rigidity.
Inner Trolley
Outer Trolley
Lock
Washers
5/16"
Clevis Pin
5/16"x1"
Ring
Fastener
Rope
Emergency
Release
Handle
Nuts
5/16"-18
Straight
Door Arm
Door
Bracket
Figure 1
Curved
Door Arm
Clevis Pin
5/16"x1-1/4"
Screws
5/16"-18x7/8"
Figure 2
Door Bracket
Hole Alignment Alternative
Figure 3:
• If holes in curved arm are above holes in straight
arm, disconnect straight arm. Cut about 6" from
the solid end. Reconnect to trolley with cut end
Hdw for
door
down
asEN/FR
shown.
• Bring arm sections together.
• Find two pairs of holes that line up and join with
screws, lock washers and nuts.
Lock
Washers
5/16"
Nuts
5/16"-18
Hardware Shown Actual Size
Screws
5/16"-18x7/8"
Cut This End
Nut 5/16"-18
Clevis Pin
5/16"x1" (Trolley)
Lock Washer 5/16"
Ring Fastener
Clevis Pin
5/16"x1-1/4" (Door Bracket)
Figure 3
Hex Screw
5/16"-18x7/8"
Proceed to Adjustment Step 1, page 28. Trolley will re-engage automatically when the opener is operated.
26
Rondelle-frein
Écrou de
Vis à tête hexagonale
de 5/16 de po-18x7/8 de po
All ONE-PIECE Doors
Assemble the Door Arm:
Can/DoorArmToTrolley 1 pc
• Fasten the straight and curved door arm sections
together to the longest possible length, with a 2 or 3
hole overlap.
• With the door closed, connect the straight door arm
section to the door bracket with the 5/16"x1-1/4"
clevis pin.
• Secure with a ring fastener.
Door
Bracket
Ring
Fastener
Lock
Washers
5/16"
Nuts
5/16"-18
Straight
Door Arm
5/16"x1-1/4"
ClevisPin
Screws
5/16"-18x7/8"
Curved Door Arm
On one-piece doors, before connecting the door arm to the trolley the travel limits must be adjusted. Limit adjustment screws are located on the left side panel as shown on page 28. Follow adjustment procedures below.
Fully Closed
Trolley
Fully Open
Trolley
Door Arm
Door Arm
Connector Hole
Closed
Door
Open Door
Door Arm
Connector Hole
Door with
Backward Slant
Door Arm
Adjustment Procedures for One-Piece Doors
Open Door Adjustment:
Decrease UP limit
• Turn the UP limit adjustment screw counterclockwise 5-1/2 turns.
• Press the Door Control push button. The trolley will
travel to the fully open position.
• Manually raise the door to the open position
(parallel to the floor), and lift the door arm to the
trolley. The arm should touch the trolley just in
back of the door arm connector hole. Refer to the
fully open trolley/door arm positions in the
illustration. If the arm does not extend far enough,
adjust the limit further. One full turn equals 2" of
trolley travel.
Closed Door Adjustment:
Decrease
DOWN limit
Anneau
d'arrêt
• Turn the DOWN limit adjustment
screwÉcrous
clockwise
de
5 complete turns.
5/16
de po-18
Rondelle-freins
de 5/16 de po
• Press the Door Control push
button. The trolley will
Biellette
travel to the fully
closed
position.
droite
Axe de chape
de the door and lift the door arm to the
• Manually
close
5/16 de po x 1-1/4 de po
Vis de touch the trolley just ahead
trolley. The arm should
5/16 de poof the door arm connector
the fully
Bielletteto
courbée
18x7/8 de po hole. Refer
closed trolley/door arm positions in the illustration. If
the arm is behind the connector hole, adjust the limit
further. One full turn equals 2" of trolley travel.
Support
de la porte
Chariot
complètement
fermé
Chariot
complètement
ouvert
Connect the door arm to the trolley.
• Close the door and join the curved arm to the connector hole in the trolley with the remaining clevis pin. It may
be necessary to lift the door slightly to make the connection.
Biellette
Trou de raccordement
• Secure with a ring fastener.
Trou de raccordement
de la biellette
de la biellette
• Run the opener through a complete travel cycle. If the door has a slight "backward" slant in full open position
as shown in the illustration, decrease the UP limit until the door is parallel to the floor.
Porte
fermée
Porte ouverte
27 Porte inclinée
vers l'arrière
Biellette
Adjustment Section: Pages 28 – 30
Adjustment Step
SEARS '92 Front to Back
13/27/92 - 4/2/92
WARNING
Adjust the UP and DOWN Limits
Do not make any limit adjustments until the
safety reversing sensors are completely
installed.
Improper adjustment of the travel limits will
interfere with the proper operation of the
safety reverse system. The door might not
reverse properly when required and could
seriously injure or kill someone under it. Test
the safety reverse system following all
adjustments to the travel limits. See page 30.
Limit adjustment settings regulate the points at
which the door will stop when moving up or down.
The door will stop in the up direction if anything
interferes with door travel. The door will reverse in
the down direction if anything interferes with the
door travel (including binding or unbalanced doors).
To operate the opener, press the Door Control push
button. Run the opener through a complete travel
cycle.
• Does the door open and close completely?
• Does the door stay closed and not reverse
unintentionally when fully closed?
If your door passes both of these tests, no limit
adjustments are necessary unless the reversing test
fails (See page 30).
CAUTION
Limit
Adjustment
Screws
2-4"
Cover
Protection
Bolt
Left Side Panel
AVERTISSEMENT
Adjustment procedures are outlined below. Run the
opener through a complete travel cycle after
each adjustment.
Repeated operation of the opener during adjustment
procedures may cause the motor to overheat and
shut off. Simply wait 15 minutes and try again.
Read the procedures carefully before proceeding to
Adjustment Step 2. Use a screwdriver to make limit
adjustments.
Adjustment Label
ATTENTION
How and When to Adjust the Limits
• If the door does not open completely, but
opens at least five feet:
Increase up travel. Turn the UP limit adjustment
screw clockwise. One turn equals 2" of travel.
NOTE: To prevent the trolley from hitting the
cover protection bolt, keep a minimum distance
of 2-4" between the trolley and the bolt.
Vis de réglage
de course
If you have2-4"
adjusted the door arm to the maximum
length and the door still will not close completely,
lower
the header bracket. See Installation Step 1,
Boulon
du 12 and 13.
pages
couvercle
• If the opener reversesPanneau
in fully
côtéclosed
gauche position:
Decrease down travel. Turn the DOWN limit
adjustment screw clockwise. One turn equals 2" of
travel.
• If door does not open at least 5 feet:
Adjust the UP (open) force as explained in
Adjustment Step 2.
• If the door reverses when closing and there is
no visible interference to travel cycle:
If the opener lights are flashing, the Safety Reversing
Sensors are either not installed, misaligned, or
obstructed. See Troubleshooting, page 23.
Test the door for binding:
Pulldethe
emergency release
Étiquette
réglage
handle. Manually open and close the door. If the door
is binding, call for garage door service. If the door is
not binding or unbalanced, adjust the DOWN (close)
force. See Adjustment Step 2.
• If the door does not close completely:
Increase down travel. Turn the DOWN limit
adjustment screw counterclockwise. One turn
equals 2" of travel.
If the door still won't close completely and the trolley
bumps into the pulley bracket (see page 4 or 5), try
lengthening the door arm (see page 26).
28
W
KG
KG
Adjustment Step 2
9
Adjust the Force
7
1
9
7
3
3
5
Too much force on the door will interfere with
the proper operation of the safety reverse
system. The door might not reverse properly
when required and could seriously injure or
kill someone under it. Do not increase the
force beyond
the 1minimum
amount
required
9
9
1
to close the door. Do not use the force
7
7
3
adjustments
to compensate
for3 a binding or
5
sticking garage
door. Test 5the safety reverse
system following
all adjustments
to force
KG
KG
levels. See page 30.
5
KG
Force adjustment
on the back
KG controls are located
panel of the opener. Force adjustment settings
Étiquette de réglage
regulate the amount of power required to open and
close the door.
The door will stop in the up direction if anything
interferes with its travel. The door will reverse in the
panel ofif anything interferes with its travel
down Back
direction
door opener
(including
binding or unbalanced doors).
Force
Adjustment
If the forces are set too light, door travel may be
Control
interrupted by nuisance reversals in the down
direction and stops in the up direction. Weather
conditions can affect the door movement, so
occasional adjustment may be needed.
The maximum force adjustment range is 260 degrees,
about 3/4 of a complete turn. Do not force controls
beyond that point. Turn force adjustment controls
with a screwdriver.
1
2
W
WARNING
1
CAUTION
Étiquette de réglage
3
9
1
7
3
9
1
7
3
5
5
KG
KG
Back panel of
door opener
Force
Adjustment
Control
1
2
3
AVERTISSEMENT
9
1
7
9
1
7
3
9
3
9
1
7
3
5
5
KG
KG
1
7
3
5
5
KG
KG
ATTENTION
Adjustment Label
9
1
3
How and When to Adjust the 7Forces
5
KG
Test the DOWN (close) force
Grasp the door bottom when the door is about
halfway through DOWN (close) travel. The door
should reverse. Reversal halfway through down
travel does not guarantee reversal on a one-inch
obstruction. See page 30. If the door is hard to
hold or doesn't reverse, decrease the DOWN (close)
force by turning the control counterclockwise.
Make 10 degree turn adjustments until the door
reverses normally. After each adjustment, run the
opener through a complete cycle.
9
1
7
3
5
KG
Make 10 degree turn adjustments until the door stops
Adjustment Labelrun the opener through
easily. After each adjustment,
a complete travel cycle.
If the door doesn't open at least 5 feet
Increase UP (Open) force by turning the control
clockwise. Make 10 degree turn adjustments until
door opens completely. Re-adjust the UP limit if
necessary. After each adjustment, run the opener
through a complete travel cycle.
If the door reverses during the down (close) cycle
and the opener lights aren't flashing
Increase DOWN (close) force by turning the control
clockwise. Make 10 degree turn adjustments until the
door completes a close cycle. After each adjustment,
run the opener through a complete travel cycle. Do
not increase the force beyond the minimum
amount required to close the door.
Test the UP (open) force
Grasp the door bottom when the door is about
halfway through UP (open) travel. The door should
stop. If the door is hard to hold or doesn't stop,
decrease UP (open) force by turning the control
counterclockwise.
29
Adjustment Step 3
WARNING
Test The Safety Reversing Sensor
Test
Without a properly working safety reversing
sensor, persons (particularly children) could be
seriously injured or killed if trapped by a closing
garage door. Repeat this test once a month.
• Press the remote control push button to open the
door.
• Place the opener carton in the path of the door.
• Press the remote control push button to close the
door. The door will not move more than an inch,
and the opener lights will flash.
Professional service is required if the opener
Safety
Reverse
System
SEARS
closes
the door
when the
safety reversing
sensor is obstructed.
The garage door opener will not close from a
remote control if the indicator light in either
sensor is off (alerting you to the fact that the
sensor is misaligned or obstructed).
The garage door can be closed by pressing and
holding the Door Control push button until down
travel is completed.
CAUTION
Safety Reversing Sensor
Safety Reversing Sensor
AVERTISSEMENT
WARNING
Adjustment Step 4
Test the Safety Reverse System
Failure to test and adjust the safety reverse
system may result in serious injury or death to
persons trapped by a closing garage door.
Repeat this test once a month and adjust as
needed.
PORTE DE GARAGE
Test:
• Place a one-inch board (or a 2x4 laid flat) on the
floor, centered under the garage door.
• Operate the door in the down direction. The door
must reverse on striking the obstruction.
GARAGE DOOR
CAUTION
ATTENTION
Adjustment:
Detector de
Detector de
seguridad
reversa
seguridad de reversa
If the door stops
ondethe
obstruction, it is not traveling
far enough in the down direction.
• Increase the DOWN limit by turning the DOWN
limit adjustment screw counterclockwise 1/4 turn.
• Repeat the test.
2x4 àmake
plat
On a sectional door,
sure limit
adjustments do not force the door arm beyond a
straight up and down position. See the
illustration on page 26.
• When the door reverses on the one-inch board,
remove the obstruction and run the opener through
1 Inch Obstruction
3 or 4 complete travel cycles to test adjustment.
Important safety check
If the door will not reverse after repeated
Repeat Adjustment Steps 1, 2 and 4 after:
adjustment attempts, call for professional
garage door service.
• Each adjustment of door arm length, force controls
or limit controls.
• Any repair to or adjustment of the garage door
(including springs and hardware).
• Any repair to or buckling of the garage floor.
• Any repair to or adjustment of the opener.
AVERTISSEMENT
ATTENTION
30
W
IMPORTANT SAFETY INSTRUCTIONS
WARNING
WARNING
WARNING
WARNING
To reduce the risk of severe injury or death to persons:
1. READ AND FOLLOW ALL INSTRUCTIONS.
2. Do not permit children either to operate or to
play with the opener. Keep remote control in a
location inaccessible to children.
3. Operate opener only when the door is in full
view and free from any obstruction. Keep the
door in sight until it is completely closed.
NO ONE SHOULD CROSS THE PATH OF THE
MOVING DOOR.
4. Check safety reversal system monthly. See
page 30. The garage door MUST reverse on
contact with a 2x4 board laid flat on the floor. If
an adjustment is made to either the force or
the limit of travel, both adjustments may be
needed and the safety reversal system must be
checked. Failure to properly adjust the opener
may result in severe injury or death.
5. If possible, use the emergency release only
when the door is in a closed position. Caution
should be taken whenever the disconnect cord
is actuated with the door open. Weak or broken
springs may cause the door to fall rapidly,
causing injury or death to persons.
6. KEEP GARAGE DOORS PROPERLY
BALANCED. See page 3. An improperly
balanced door may not reverse when required
and could result in severe injury or death.
Repairs to cables, spring assemblies and other
hardware must be made by a professional
garage door person.
7. Disconnect the electric power to the garage
door opener before making any repairs or
removing the covers.
CAUTION
CAUTION
WARNING
WARNING
8.
SAVE THESE INSTRUCTIONS.
AVERTISSEMENT
AVERTISSEMENT
AVERTISSEMENT
AVERTISSEMENT
The remote control
Care of Your Opener
3-FUNCTION
Open this end
first to avoid
cracking
housing
The lithium batteries should
produce power for up to
5 years. To replace batteries,
use the visor clip or screwdriver
blade to pry open the case, as COMPACT
Twist here
shown. (“Open” location is
to open
stamped on back of transmitter
case.) Insert batteries positive side down.
Replace cover as follows. 3-Function remote: Insert
the 3 tabs at the opposite end and snap shut. Compact
3-Function remote: Snap shut along both sides.
Dispose of old batteries properly.
Limit and force adjustment controls
Limit Controls
Force Controls
9
9
1
7
5
9
7
3
5
9
1
KG
7
3
1
KG
5
3
5
Adjustment
Label
KG
KG
Adjustment Label
(Located on the left side panel)
Adjustment Label
AVERTISSEMENT
AVERTISSEMENT
1
7
3
ATTENTION
ATTENTION
Adjustment Label
(Located on the back panel)
Weather conditions may cause some minor
changes in door operation requiring some readjustments, particularly during the first year of
operation.
Pages 28 and 29 refer to the limit and force
Étiquette de réglage
adjustments. Only a screwdriver is required. Follow
Étiquette de réglage
Étiquette de carefully.
réglage
the instructions
Repeat the safety reverse test (page
after any
Étiquette30)
de réglage
adjustment of limits or force.
9
9
1
7
5
9
7
1
KG
1
7
3
3
3
5
9
7
1
KG
5
5
KG
KG
WARNING
3
Keep batteries away from small children. If
swallowed, promptly notify doctor.
Maintenance Schedule
CAUTION
Once a Month
Manually operate door. If it is unbalanced or
binding, call for professional garage door service.
Check to be sure door opens & closes fully.
Adjust limits and/or force if necessary.
(See pages 28 and 29.)
Repeat the safety reverse test. Make any
necessary adjustments (See page 30).
Twice a Year
Check chain tension. Disconnect trolley first.
Adjust if necessary (See page 11).
Once a Year
Oil door rollers, bearings and hinges. The opener
does not require additional lubrication. Do not
grease the door tracks.
31
Operation of Your Opener
Manual Disconnect and Lockout
Sears -92
W
WARNING
9/7/90, 3/2/92
Activate the opener with any of the following:
• The Remote Control: Hold push button down until
the door starts to move.
• The Door Control: Hold push button down until
the door starts to move.
• The Outdoor Key Switch or Keyless Entry: (See
Accessories)
Weak or broken springs could allow an open
door to fall (either rapidly or unexpectedly),
resulting in serious injury, death or property
damage. If possible, use the emergency
release rope and handle only when the door is
fully closed.
When the opener is activated with the safety
reversing sensor installed and correctly aligned:
1. If open, the door will close. If closed, the door will
To open the door
open.
manually:
2. If closing, the door will reverse.
The door should be fully
3. If opening, the door will stop (allowing space for
closed if possible. Pull
Trolley
entry and exit of pets and for fresh air).
Manual Disconnect
and
Release
Arm Lockout
down on the red
Trolley
4. If the door has been stopped in a partially open
Trolley
emergency release
Sears -92
position, it will close.
Emergency
Emergency
9/7/90, 3/2/92 handle and lift the door
Release Hand
5. If obstructed while closing, the door will reverse.
manually. To reconnect
Release Handle
(Pull Down & B
NO
(Pull Down)
TIC
E
the door to the opener,
6. If obstructed while opening, the door will stop.
Towards Open
press the Door Control
7. The garage door will reverse in the closing cycle
push button.
when the invisible beam is broken. If fully open,
Manual disconnect
the door will not close when the beam is broken.
position
The sensor has no effect in the opening cycle.
If the sensor is not installed, or is not aligned
The lockout feature
correctly, the door won't close from any remote
prevents the trolley from
transmitter. You can close the door with the Door
reconnecting autoControl, the Outdoor Key Switch, or Keyless Entry,
matically. Pull the
however, if you activate them until down travel is
Trolley
Trolley
Trolley
emergency handle down
complete. If you release them too soon, the door will
Release
Arm Arm
Release
Release Arm
and
back
(toward
the
reverse.
Trolley
Trolley
Trolley
opener). The door can
The opener light will blink for 5 seconds when the
then be raised and
Emergency
safety reversing sensor causes theEmergency
door to reverse.
Release Handle
Release Handle
lowered
manually
as
often
(Pull Down & Back
NO
Opener Light will turn on under the
following
(Pull
Down)
TIC
E
NOTICE
as necessary. To
Towards Opener)
conditions: When the opener is initially plugged in;
disengage the Lockout
when the power is interrupted; when the opener is
Feature, pull the
activated. They will turn off automatically after 4-1/2
emergency handle straight
Lockout position
minutes or provide constant light when the Light
down. The trolley will
feature is activated. SECURITY✚ models: Lights will
reconnect on the next UP
also turn on when someone walks through the open
or Down operation.
garage door. Bulb size is 75 watts maximum.
CAUTION
AVERTISSEMENT
ATTENTION
Operation of the Door Controls
Trolley
Release Arm
(see page 18)
Trolley
Press the lighted push button to open or close the
door.
Press again to reverse the door during the closing
cycle or to stop the door while it's opening.
32
Receiver and Remote Control Programming
To comply with FCC/IC rules, adjustment or modifications of this receiver
and/or transmitter are prohibited, except for changing the code setting or
replacing the battery. THERE ARE NO OTHER USER SERVICEABLE
PARTS.
Your garage door opener receiver and remote control
have been pre-set at the factory. The door will open
when you press the LARGE remote control push
button. THE CODE BETWEEN THE REMOTE
CONTROL AND THE RECEIVER CHANGES WITH
EACH USE, randomly accessing over 100 billion new
codes.
The 3-function remote control can also activate
additional SECURITY✚ garage door openers and/or
light controls.
Your SECURITY✚ opener will operate with:
• several SECURITY✚ remote controls (with blue
push buttons) utilizing up to 8 functions.
• one SECURITY✚ Keyless Entry System (Model
18795).
Adjust Force - SEARS
Follow the instructions below to program your opener
to match any additional remotes you may purchase.
See Accessories on page 38.
WARNING
Children operating or playing with a garage
door opener can injure themselves or others.
The garage door could close and cause serious
injury or death. Do not allow children to operate
the door push button(s) or remote control(s).
A moving garage door could injure or kill
someone under it. Activate the opener only
when you can see the door clearly, it is free of
obstructions, and is properly adjusted.
CAUTION
Figure 1
Select a remote control push
button to operate opener
To Add A Remote Control
1. Press and hold the selected remote control push
button. See Figure 1.
2. Then press and release the SRT (learn) button on
the back panel of the opener, Figure 2. The
indicator light on the back panel will begin to blink
and the opener light will flash once.
3. Release the remote push button.
Test by pressing the remote push button.
SECURITY✚
AVERTISSEMENT
3-Function
Remote Control
To Erase All Remote Control Codes
Press and hold the SRT button on the opener panel
until the indicator light turns off (about 6 seconds). All
remote control codes are now erased. Then follow
the steps above to re-program each remote control.
Figure 2
Choisir un bouton-poussoir
pour faire fonctionner l'ouvre-porte
Garage Door Opener
(With "Smart" Button)
ATTENTION
1
SECURITY✚
Télécommande à
3 fonctions
BACK
To Add the Keyless Entry
We recommend that you program your password
before you install the Keyless Entry. You will not
need assistance, and you can test the reception
at the mounting location before installation.
1. Choose a 4-digit password using numbers from
0 to 9 (a number can be used more than once, for
example, 4, 0, 4, 1).
2. Press the four buttons for the password, then
press and hold the Enter button. The indicator
light on the door opener back panel will blink.
3. Press and release the SRT (learn) button on the
opener panel. After the opener light flashes,
release the Enter button.
Test by pressing the password, then press Enter.
The door should begin to move.
2
3
9
PANEL
"SRT" (learn)
Button
9
1
7
1
7
3
3
5
5
KG
KG
Indicator
Light
Code programming instructions are
also located on the back panel.
Ouvre-porte de garage
(avec bouton "SRT")
1
2
3
9
1
7
33
PANNEAU
ARRIÈRE
Témoin
Bouton
"SRT" (intelligent)
3
9
1
7
3
5
5
KG
KG
Having a Problem?
Situation
Probable Cause and Solution
The opener doesn't
operate from either
the Door Control or
the remote control:
1. Does the opener have electric power? Plug a lamp into the outlet. If it doesn't light,
check the fuse box or the circuit breaker. (Some outlets are controlled by a door switch.)
2. Have you disabled all door locks? Review installation instruction warnings on Page 11.
3. Is there a build-up of ice or snow under the door? The door may be frozen to the
ground. Remove any restriction.
4. The garage door spring may be broken. Have it replaced.
5. Repeated operation may have tripped the overload protector in the motor. Wait
15 minutes. Try again.
Opener operates
from the remote
control, but not from
the Door Control:
1. Is the Door Control lit? If not, remove the bell wire from the opener terminal screws.
Short the red and white terminals by touching both terminals at the same time with a
piece of wire. If the opener runs, check for a faulty wire connection at the Door
Control, a short under the staples, or a broken wire.
2. Are the wiring connections correct? Review Step 6, page 18.
The door operates
from the Door
Control, but not from
the remote control:
1. Is any door push button flashing? If your model has the Lock feature, make sure the
lock is Off.
2. Your opener needs to re-learn a remote control code. Refer to Instructions on the
opener panel.
3. Program the receiver to match the remote control code.
4. Repeat the receiver programming procedure with all remote controls.
The remote control
has short range:
1. Change the location of the remote control in your car.
2. Check to be sure the antenna on the side or back panel of opener extends fully
downward.
3. Some installations may have shorter range due to a metal door, foil backed
insulation, or metal garage siding. (Antenna Extender Kit 41A3504)
Opener noise is
disturbing in living
quarters of home:
If operational noise is a problem because of proximity of the opener to the living
quarters, the Vibration Isolator Kit 41A3263 can be installed. This kit was designed to
minimize vibration to the house and is easy to install.
The garage door
opens and closes
by itself:
1. Be sure that all remote control push buttons are not stuck in the “ON” position.
2. Remove the bell wire from the Door Control terminals and operate from the remote
control only. If this solves the problem, the Door Control is faulty (replace), or there is
an intermittent short on the wire between the Door Control and the opener.
3. Clear memory and re-program all remote controls.
The door doesn't
open completely:
1. Is something obstructing the door? Remove the obstruction or repair the door.
2. If the door has been working properly but now doesn't open all the way, increase the
up force. See page 29.
3. If door opens at least 5 feet, the travel limits may need to be increased. One turn
equals 2 inches of travel. See page 28.
Repeat the safety reverse test after the adjustment is complete.
The door stops but
doesn't close
completely:
Review the travel limits adjustment procedures on page 28.
Repeat the safety reverse test after any adjustment of door arm length, close
force or down limit.
34
Having a Problem? (continued)
Situation
Probable Cause & Solution
The door opens but
won't close:
1. If the opener lights blink, check the safety reversing sensor. See page 23.
2. If the opener lights do not blink and it is a new installation, check the down force.
See Adjustment Step 2, page 29. For an existing installation, see below.
Repeat the safety reverse test after the adjustment is complete.
The door reverses for
no apparent reason
and opener lights
don't blink:
1. Is something obstructing the door? Pull the red emergency release handle. Operate
the door manually. If it is unbalanced or binding, call for professional garage door
service.
2. Clear any ice or snow from the garage floor area where the door closes.
3. Review the force adjustment procedures on page 29.
4. If door reverses in the fully closed position, decrease the travel limits (page 28).
Repeat safety reverse test after adjustments to force or travel limits. The need
for occasional adjustment of the force and limit settings is normal. Weather
conditions in particular can affect door travel.
The door reverses for
no apparent reason
and opener lights
blink for 5 seconds
after reversing:
Check the safety reversing sensor. Remove any obstruction or align the receiving eye.
See page 23.
The opener light:
. . . doesn't turn on:
Replace the light bulbs (75 watts maximum). Use a standard neck garage door opener
bulb if regular bulb burns out.
. . . doesn't turn off:
Is the Light feature on? Turn it off.
The opener strains or
maximum force is
needed to operate
door:
The door may be out of balance or the springs are broken. Close the door and use the
emergency release to disconnect the trolley. Open and close the door manually. A properly
balanced door will stay in any point of travel while being supported entirely by its springs. If it
does not, disconnect the opener and call a professional garage door serviceman. Do not
increase the force to operate the opener.
The opener motor
hums briefly, then
won't work:
1. The garage door springs are broken. See above.
2. If the problem occurs on the first operation of the opener, door may be locked. Disable
the door lock. If the chain was removed and reinstalled, the motor may be out of phase.
Remove the chain; cycle the motor to the down position. Observe the drive sprocket.
When it turns in a clockwise direction and stops in the down position, reinstall the chain.
Repeat the safety reverse test after the adjustment is complete.
The opener won't
operate due to
power failure:
1. Use the emergency release to disconnect the trolley. The door can be opened and closed
manually. When the power is restored, press the Door Control push button and trolley will
automatically reconnect (unless trolley is in lockout position.) See page 32.
2. The Outside Trolley Release accessory (for use on garages with no service door)
disconnects the trolley from outside the garage in case of power failure.
The chain droops
or sags:
It is normal for the chain to droop slightly in the closed door position. Use the
emergency release to disconnect the trolley. If the chain returns to normal height when
the trolley is disengaged and the door reverses on a one-inch board, no adjustments
are needed (see page 11).
35
Repair Parts
Rail Assembly Parts
3
4
2
1
7
E
AS
GRE
RAILO. 83A4
N
RAGE
TO GA
DOOR
4
5
6
KEY
NO.
PART
NO.
1
2
3
4
5
6
7
1A995
41A3489
1B3117
183B110
41B2616
41A3473
83A4
DESCRIPTION
Master link kit
Complete trolley assembly
T-rail – center section
T-rail – end section (each)
Cable pulley bracket assembly
Chain and cable
Rail grease
NOT SHOWN
Rail assembly hardware kit
(see page 7)
41A3534
Installation Parts
FOR REMOTE MODEL
139.18791B
FOR REMOTE MODEL
139.18791
3A
NLY
TO
UN
G
LIN
MO
CEI
UP
3B
5
6
4
KEY PART
NO. NO.
1
2
41A4899
41A5032
3A
3B
4
5
6
7
8
9
10
10A19
10A20
29B134
41A2828
41A4353
217A238
178B35
41A5047
41A4373A
11
12
13
14
15
12B483
12B484
12B485
12B350
178B34
41A3475-4
41A4116
114A2147
2
2
1
NOT
ICE
8
DESCRIPTION
7
Standard control console
3-function remote control housing
(no circuit board)
3V 2016 Lithium battery (2 Required)
3V 2032 Lithium battery (1 Required)
Visor clip
Emergency rope & handle assy.
Header bracket w/clevis pin & fastener
2-conductor bell wire - white & white/red
Curved door arm section
Door bracket w/clevis pin & fastener
Safety sensor kit (receiving and sending eyes)
with 3' 2-conductor bell wire attached
"C" wrap bracket
Square hole bracket
Slotted bracket
Hanging brackets
Straight door arm section
NOT SHOWN
Installation hardware bag (see page 7)
Safety sensor installation hardware
(see page 7)
Owner's manual
36
10
9
14
11
15
12
13
Repair Parts
88 Opener Assembly Parts
1
2
4
3
6
16
20
5
8
19
18
17
16
Brown
Wire
(Down)
Contact
DN
UP
Drive
Gear
Center Limit
Contact
KEY PART
NO. NO.
1
2
31D380
41C4220A
3
41A2817
4
5
6
7
8
9
10
41B4245
41A4352
175B88
108D48-2
30B363
12A373
41A3150
10
3
(Up)
Contact
14
7
11
13
15
LIMIT SWITCH
ASSEMBLY
9
12
Grey
Wire
Yellow
Wire
KEY PART
NO. NO.
DESCRIPTION
DESCRIPTION
11
41D3058
Universal replacement motor and
Sprocket cover
bracket assembly
Gear and sprocket assy.
with: Motor, worm,
Complete
with:View SEARS 315-699 (Yellow DiskComplete
Exploded
#3)
bracket, bearing assembly, RPM
Spring washer
Models
sensor
Thrust
washer53315, 53415, 53615, 53625 & 53699
12
41D328-4
Cover - 1/2 h.p.
Retaining ring
4/3/89 - 6/20/89 - 6/25/89
8/2/90
13
41A2818
Helical gear and retainer w/grease
Bearing plate
14
41D3452
Limit switch assembly
Roll pins (2)
15
41C4398A RPM sensor assembly
Drive gear and worm gear
16
41C4246
Wire harness assy. w/plug
Helical gear w/retainer and
17
41A2826
Shaft bearing kit
grease
18
41A2822A
Interrupter cup assy.
Drive/worm gear kit w/grease
19
41A5021-3B Receiver logic board assy.
Roll pins (2)
Complete with:
Line cord
Logic board
End panel
End panel w/all labels
Light socket
20
41A3691
End panel w/all labels
Lens
NOT SHOWN
Capacitor - 1/2 h.p.
41A2825
Opener
assembly hardware kit
Capacitor bracket
(includes screws not designated by a
Terminal block w/screws
number in illus.)
37
Accessories
Accessories Art - SEARS 92
Sears offers many
useful
accessories
Accessories
Art
-to
SEARS
Side
Side 92for your garage door opener. They are illustrated below with
Sears model numbers and
descriptions
Side to Side
3/3/92
18752
3/3/92
Outside Trolley Release:
18792
Required for a garage with NO
access door.
18756
SECURITY✚ 3-Function Remote
Control:
Includes visor clip.
Outdoor Key Switch:
Opens the garage door
automatically from outside when
remote control is not handy.
18754
8 ft. Rail Extension:
To allow an 8 foot door to open fully.
18753
10 ft. Rail Extension:
To allow a 10 foot door to open fully.
18785
Door Clearance Brackets:
(For Sectional Doors Only)
Replace top brackets and rollers
on door to reduce height of door
travel. For use when installing
opener in garage with low
headroom clearance.
SECURITY✚ Compact
3-Function Remote Control:
With loop for attaching key ring.
(Available August, 1997)
18790
SECURITY✚ Single-Function
Remote Control:
Includes visor clip.
(Available May, 1997)
18795
SECURITY✚ Keyless Entry:
Enables homeowner to operate garage
door opener from outside by entering a
password. Also can add a temporary
password for visitors or service persons.
This temporary password can be limited
to a programmable number of hours or
entries. (Available May, 1997)
38
Index
Access Door/Outside Key Release Accessory ...............................................................................................4, 5
Chain Tension ..............................................................................................................................................4, 5, 11
Electrical Safety Warnings........................................................................................................................2, 20, 31
Garage Door
Testing for balance, binding and sticking...................................................................................................3, 28, 31
Determining high point of travel:
Sectional door...................................................................................................................................................12
One-piece door .................................................................................................................................................13
Disabling existing locks....................................................................................................................................3, 11
Door clearance brackets (for garages with low headroom) ...........................................................................12, 38
Force controls
Adjustment procedures.................................................................................................................................... 29
Problems that might require force adjustments ..........................................................................................34, 35
Safety warnings ..........................................................................................................................................29, 31
Door hardware .....................................................................................................................3, 9, 11, 12, 18, 31, 32
Maintenance instruction label ........................................................................................................................11, 28
Reinforcement requirements ...........................................................................................................................4, 24
Removing of all ropes .......................................................................................................................................3, 11
Possible door damage ...................................................................................................................................16, 24
Travel limits
Adjustment procedures.....................................................................................................................................28
Problems that might require limit adjustments............................................................................................34, 35
Safety warnings ..........................................................................................................................................28, 31
Manual (Emergency) Release Rope & Handle
Lockout feature ....................................................................................................................................................32
Manual disconnect...............................................................................................................................................32
Safety warnings .................................................................................................................................11, 19, 31, 32
Opener Terminals
Door control connections .....................................................................................................................................18
Safety reversing sensor connections...................................................................................................................23
Operational Noise
Sprocket noise .....................................................................................................................................................11
Vibration noise (isolator kit) .................................................................................................................................34
Receiver and Remote Control
Programming the receiver ...................................................................................................................................33
Erasing all codes .................................................................................................................................................33
Activating other openers ......................................................................................................................................33
Safety warning .....................................................................................................................................................33
Problems with remote control operation ..............................................................................................................34
Safety Reverse Test Procedure..........................................................................................................................30
Testing required.................................................................................................................................11, 30, 34, 35
Safety reverse system problems
Securing header bracket to wall .......................................................................................................................12
Adjusting travel limits ........................................................................................................................................28
Applying excessive force on the door ...............................................................................................................29
Buckling or uneven floor .................................................................................................................................4, 5
Safety Warnings.........................................................2, 3, 9, 11, 12, 16, 18, 19, 20, 21, 24, 28, 29, 30, 31, 32, 33
User Instruction Label for garage wall ........................................................................................................11, 18
39
®
OWNER’S
MANUAL
Model No.
139.18847
139.18857
®
GARAGE DOOR OPENER
SERVICE AND REPAIR PARTS
CALL 1-800-665-4455*
MD
MD or need
Keep this number handy should you require a service call
to order repair parts. If ordering parts make sure you have the
name, make and model no. of the merchandise and the name and
number of the part you wish to order.
To purchase a Sears Maintenance Agreeement – ask any salesperson
or call Sears Service today.
* If calling locally, please use one of the following numbers:
Regina
566-5124
Montreal
333-5740
Toronto
744-4900
Halifax
454-2444
Kitchener
894-7590
Ottawa
738-4440
Vancouver
420-8211
The model number
label is located under
the light lens on the
left side panel of your
opener.
SEARS WARRANTY
FULL 90-DAY WARRANTY ON GARAGE DOOR OPENER
When requesting
service or ordering
parts, always provide
the following
information:
■
■
■
■
Product Type
Model Number
Part Number
Part Description
When the garage door opener is installed, adjusted and operated in
accordance with our instructions, Sears will, for a period of 90 days from the
date of purchase, repair any defect in workmanship in the garage door
opener at no charge.
LIMITED WARRANTY
From the 91st day until one year from the date of purchase, Sears will
furnish replacement parts for any defective parts, free of charge. You pay
for labor.
LIMITED WARRANTY ON MOTOR
1/2 HP Motor: After 1 year and through 5 years, Sears will furnish
replacement parts for any defective parts in motor, free of charge. You pay
for the labor.
WARRANTY SERVICE IS AVAILABLE BY SIMPLY CONTACTING THE
NEAREST SEARS STORE OR SERVICE CENTER
This warranty gives you specific legal rights, and you may also have other
rights which vary from province to province.
SEARS CANADA, INC., TORONTO, ONTARIO M5B 2B8
114A2147C
© 1997, Sears Canada, Inc.
All Rights Reserved
Printed in Mexico