Electrolux E)09C2ASK(W Unit installation

INSTRUCTIONS MANUAL
SPLIT TYPE ROOM AIR CONDITIONER
MODELS:
EAS(C,E)09C2ASK(W,S,M) / EAS(C,E)12C2ASK(W,S,M)
EAS(C,E)18C2ASK(W,S,M) / EAS(C,E)24C2ASK(W,S,M)
EAS(C,E)09P5ASK(W,S,M) / EAS(C,E)12P5ASK(W,S,M)
EAS(C,E)18P5ASK(W,S,M) / EAS(C,E)24P5ASK(W,S,M)
110823P
S(351-358)EM_ENGLISH
Please read this manual completely before operating your room air conditioner.
contents electrolux 02
01 electrolux welcome
Welcome to the world of
simple handling and no worries.
Contents
Thank you for choosing Electrolux. This manual contains all of the information
required to guarantee your safety and the appropriate use of your air
conditioner.
01.
02.
03.
04.
05.
Please read all of the instructions before using the air conditioner and keep this
manual for future reference.
We know you will enjoy your new air conditioner and thank you for choosing our
product. We hope you will consider us for future purchase.
Environmental Advices
The packaging material used is recyclable; we
recommend that you separate plastic, paper and
cardboard and give them to recycling companies.
According to WEEE (Waste of Electrical and
Electronic Equipment) guidelines, waste from
electrical and electronic devices should be
collected separately. If you need to dispose of this
appliance in the future, do NOT throw it away with
the rest of your domestic garbage. Instead, please
take the appliance to the nearest WEEE collection
point, where available.
The air conditioner you purchased has R410a gas
refrigerant a environmental friendly gas which does
not damage the ozone layer.
The air conditioner that you have bought may be slightly different from the one
illustrated in this manual. Please refer to the information related to the model
you have.
This air conditioner is for domestic use only. It is not reccomended for
commercial or industrial use.
The air conditioner you have may carry a different plug than the one illustrated
in this manual. The plug that comes with the product follows the electrical
specification of the country where it is sold.
Welcome.........................................................................................................01
Environmental advices....................................................................................01
Contents..........................................................................................................02
Safety precautions..........................................................................................04
Installation.......................................................................................................08
5.1 Choosing the installation site..............................................................08
5.2 Parts list...............................................................................................10
5.3 Indoor unit installation..........................................................................12
5.4 Outdoor unit installation.......................................................................16
5.5 Refrigerant pipe connection................................................................18
5.6 Electrical work......................................................................................20
5.7 Electrical safety....................................................................................28
5.8 Gas leak check....................................................................................28
5.9 Operation test.......................................................................................29
06. Operation........................................................................................................30
6.1 Preparing the device for operation......................................................30
6.2 Product description.............................................................................31
6.3 Remote control....................................................................................33
- Remote control operation
- Remote control battery
- When should the batteries be replaced
- To replace batteries
- Remote control instructions
6.4 Remote control description.................................................................35
- On/off
- Mode
- Swing
- Sleep
- Follow me
- Direction
- Restart
- Temperature
- Fan speed
- Timer
- Cancel
- Turbo
- LED
- Clock
- Lock
6.5 LCD display indicators........................................................................38
6.6 Clock adjustment.................................................................................39
03 electrolux contents
safety precautions electrolux 04
Safety precautions
6.7 How the air conditioner works.............................................................40
- Automatic operation
- Cool/Heat and Fan only operation
- Dry operation
- Air flow direction adjustment
- Sleep mode
- Timer
- Cancel timer operation
- Optimal operation
6.8 How to use the indoor unit...................................................................44
- Adjusting the air flow direction
- Adjusting the vertical air flow direction (up-down)
- To set the horizontal air flow direction (left-right)
- To automatically swing the air flow direction (up-down)
6.9 Manual operation..................................................................................46
07. Maintenance.........................................................................................47
08. Operation tips.......................................................................................49
09. Solutions for problems.........................................................................51
10. Technical specifications.......................................................................52
To prevent injury to the user or other people and property damage, the following
instructions must be followed.
Incorrect operation due to ignoring of instructions may cause harm or damage.
The seriousness is classified by the following indications.
1. Connect with the power properly.
Otherwise, it may cause electric
shock or fire due to excess heat
generation.
2. Do not modify power cord length
or share the outlet with other
appliances. It may cause electric
shock or fire due to heat
generation.
3. Always ensure effective earthing.
No earthing may cause electric
shock.
4. Disconnect the power if strange
sounds, smell, or smoke comes
from it. It may cause fire and
electric shock.
5. Keep firearms away. It may cause
fire.
6. Do not operate or stop the unit by
switching on or off the power. It
may cause electric shock or fire
due to heat generation.
7. Do not operate with wet hands or
in damp environment. It may cause
electric shock.
8. Do not allow water to run into
electric parts. It may cause failure
of machine or electric shock.
9. Do not drink water drained from air
safety precautions electrolux 06
05 electrolux safety precautions
conditioner. It contains
contaminants and could make you
sick.
10.Do not use the power cord close to
heating appliances. It may cause
fire and electric shock.
11.Do not damage or use an
unspecified power cord. It may
cause electric shock or fire.
12.Do not direct airflow at room
occupants only. This could damage
your health.
13.Always install circuit breaker and a
dedicated power circuit. No
installation may cause fire and
electric shock.
14.Do not open the unit during
operation. It may cause electric
shock.
15.Do not use the power cord near
flammable gas or combustibles,
such as gasoline, benzene, thinner,
etc. It may cause an explosion or
fire.
16.Ventilate room before operating air
conditioner if there is a gas leakage
from another appliance. It may
cause explosion, fire and, burns.
17.Do not disassemble or modify unit.
It may cause failure and electric
shock.
18.When the air filter is to be removed,
do not touch the metal parts of the
unit. It may cause an injury.
19.Do not clean the air conditioner
with water. Water may enter the
unit and degrade the insulation. It
may cause an electric shock.
20.Ventilate the room well when used
together with a stove, etc. An
oxygen shortage may occur.
21.When the unit is to be cleaned,
switch off, and turn off the circuit
breaker. Do not clean unit when
power is on as it may cause fire
and electric shock, it may cause
an injury.
22.Do not put a children, pet or house
plant where it will be exposed to
direct air flow. This could injure the
pet or plant.
23.Do not use for special purposes.
Do not use this air conditioner to
preserve precision devices, food,
pets, plants, and art objects. It
may cause deterioration of quality,
etc.
24.Stop operation and close the
window in storm or hurricane.
Operation with windows opened
may cause wetting of indoor and
soaking of household furniture.
25.Turn off the main power switch
when not using the unit for a long
time. It may cause failure of
product or fire.
26.Do not use strong detergent such
as wax or thinner. Use a soft cloth
for cleaning. Appearance may be
deteriorated due to change of
product color or scratching of its
surface.
27.Ensure that the installation bracket
of the outdoor appliance is not
damaged due to prolonged
exposure. If bracket is damaged,
choosing the installation site electrolux 08
07 electrolux safety precautions
Choosing the installation site
there is concern of damage due to
falling of unit.
28.Always insert the filters securely.
Clean filter once every two weeks.
Operation without filters may
cause failure.
29.Do not place heavy object on the
power cord and take care so that
the cord is not compressed. There
is danger of fire or electric shock.
30.Do not place obstacles around airinlets or inside of air-outlet. It may
cause failure of appliance or
accident.
Precautions for Installation
Installation at the following sites may cause problems. If you must inevitably
install the unit at one of these sites, please consult your local distributor
beforehand:
1. Site with machine oil.
2. Sites with a high concentration of salinity, such as coastal areas.
3. Sites with sulfuric gas, such as hot water springs.
4. Sites with high frequency equipment, such as wireless equipment, welding
machines and medical installations.
5. Sites with flammable gases or volatile material.
6. Sites with special environmental conditions.
7. Laundry rooms.
Indoor Unit
1. The unit must be installed at a site
that does not obstruct the flow of
air.
2. The site must support the weight
of the indoor unit.
3. The site must be easily accessible
for maintenance and replacement
of the air filter.
4. The site must allow for the
necessary space around the
indoor unit, as shown in the
following figure.
5. There should be at least 1 meter (3
feet) between the unit and radio
and television devices. It is ideal
that the unit be installed at the
center of the environment.
6. It must be far from fire, smoke or
flammable gases.
7. The indoor unit must be at least 2.3
meters (7.5 feet) from the ground.
8. The site must allow for the easy
removal of the connector pipe and
drain hose.
9. The unit must be installed at a site
protected from direct sunlight.
More
than 15cm
More
than 12cm
More
than 12cm
More
than 200cm
parts list electrolux 10
09 electrolux outdoor unit
Parts list
Outdoor Unit
1. The outdoor unit must be installed
at a convenient site that is not
exposed to strong winds. The site
should be dry and well ventilated.
More
than 30cm
More
than 60cm
More
than 30cm
2. The site must support the weight
of the outdoor unit and allow for
vertical installation.
3. There must not be the possibility of
increased noise and vibration at
the site.
4. The unit must be installed at a site
where the noise produced by its
operation and air discharge does
not disturb the neighbors or
animals.
More
than 200cm
NUMBERING
PART NAME
QTY.
1
Installation plate
1
2
Clip anchor
8
3
Self-tapping screw A ST3.9x25
8
4
Seal
1
5
Drain Joint
1
6
Connecting
pipe
assembly*
More
than 60cm
Liquid side
Ø6,35
Gas side
Ø9,52 (< modelos 12000 Btu’s)
Parts you must
purchase
Ø12,7 (> modelos 12000 Btu’s)
7
Remote controller
1
8
Self-tapping screw B ST2.9x10
2
9
Remote controller holder
1
5. The site cannot have any leakage
of flammable gases.
6. The site must allow for a piping
extension of no less than 5 meters
(16 feet) and for pipes measuring
at least 10 meters (33 feet) in
length.
7. The site must provide enough
space around the unit, as shown in
the diagram.
9
Indoor unit
8
7
8
8. Children must not be able to
access the installation site.
4
1
5
3
2
Outdoor unit
indoor unit installation electrolux 12
11 electrolux parts list
Indoor unit installation
Installation plate description
1
More than 15cm
2
3
above 150mm from Installation plate
the ceiling
Indoor unit outline
Indoor unit
More than 12cm
above 120mm
from the wall
90
40
40
45
6
B
above 120mm
from the wall
Refrigerant pipe
hole (left) Ø 65
A
More than 12cm
Refrigerant pipe
hole (right) Ø 65
Models < 12000 Btu’s (A: 710, B: 250)
Model 12000 Btu’s (A: 790, B: 265)
Air filter
6
More than 60cm
7
above 150mm from Installation plate
the ceiling
Indoor unit outline
A
More than
60cm
above 120mm
from the wall
293
More than 30cm
90
45
above 120mm
from the wall
45
Refrigerant pipe
hole (left) Ø 65
45
4
Refrigerant pipe
hole (right) Ø 65
920
5
Outdoor
unit
Refrigerant pipe
hole (left) Ø 65
45
272
above 120mm
from the wall
1. This illustration is for explanation purposes only.
2. Copper lines must be insulated independently
above 150mm from Installation plate
the ceiling
Indoor unit outline
90
45
More than 200cm
(A)
45
C
305
B
80
489
850
(B)
Modelos 18000 Btu’s
above 120mm
from the wall
Refrigerant pipe
hole (right) Ø 65
indoor unit installation electrolux 14
13 electrolux indoor unit installation
150mm del techo
Connective pipe and drainage installation
998
119
Drainage
above 120mm
from the wall
1. Run the drain hose sloping
downward. Do not install the drain
hose as illustrated below.
Indoor unit outline
Modelos 24000 Btu’s
Fixing the installation plate
Connective pipe installation
1. Install the installation plate
horizontally over the structural
parts on the wall using the spaces
indicated on the plate, as shown in
the figure above.
2. In the case of tiled, concrete or
similar walls, create 5 mmdiameter holes. Place anchorage
supports for the appropriate
assembly screws.
3. If expansion screws are used, the
holes must measure 11x20 or
11x26, with a distance of 450 mm
between each.
4. Fix the installation plate to the wall.
1. For the left-hand and right-hand
piping, remove the pipe cover from
the side panel.
Drilling the Hole
Fit the Installation Plate and drill holes
in the wall according to the wall
structure and corresponding mounting
points on the installation plate
(Dimensions are in “mm” unless
otherwise stated).
Wall
Indoor unit
Outdoor unit
5-7mm
1. Determine the position of the hole
for the pipe using the installation
plate and drill the pipe hole (ø
65mm) so that it is titled slightly
downward.
2. Always use a pipe cover with an
opening when drilling a metal bar.
3. Fix the end of the connective pipe.
Do not put the end
of drain hose into water.
Pipe cover
(right)
Pipe
holder
Pipe cover
(left)
Right back
piping
Right piping
Indoor unit
outline
Connective
pipe
43mm
Placa de instalación
2. For the rear-right-hand and rear-lefthand piping, install the piping as
shown. Bend the connective pipe to
be laid at 43mm height or less from
the wall.
Do not block
water flow
by a rise.
Do not block
water flow
by a rise.
2. When connecting extension drain
hose, insulate the connecting part
of extension drain hose with a
shield pipe, do not let the drain
hose slack.
130
50
Refrigerant pipe
hole (left) Ø 65
130
50
293
above 120mm
from the wall
380
41
380
Fastening the Indoor Unit
1. Pass the piping through the hole in
the wall.
2. Put the upper claw at the back of the
indoor unit on the upper hook of the
installation plate, move the indoor
unit from side to side to see that it is
securely hooked (see Fig.10 &
Fig.11).
Upper hook
Lower hook
outdoor unit installation electrolux 16
15 electrolux indoor unit installation
Outdoor unit installation
3. Piping can easily be made by lifting
the indoor unit with a cushioning
material between the indoor unit
and the wall. Get it out after finish
piping.
4. Push the lower part of the indoor unit
up on the wall, then move the
indoor unit from side to side, up and
down to check if it is hooked
securely.
Piping and wrapping
1. Bundle the tubing, connecting
cable, and drain hose with tape
securely, evenly as shown.
2. Because the condensed water
from rear of the indoor unit is
gathered in ponding box and is
piped out of room. Do not put
anything else in the box.
Cushioning
material
Indoor unit
Cable
de conexión
Ponding
box
Pipe room
Connective
pipe
Drain hose
Wrapping
belt
1. Connect the indoor unit first, then the outdoor unit.
2. Do not allow the piping to let out from the back of the indoor unit.
3. Be careful not to let the drain hose slack.
4. Heat insulated both of the auxiliary piping.
5. Be sure that the drain hose is located at the lowest side of the bundle.
Locating at the upper side can cause drain pan to overflow inside the unit.
6. Never intercross nor intertwist the power wire with any other wiring.
7. Run the drain hose sloped downward to drain out the condensed water
smoothly.
1. Install the outdoor unit on a rigid
base to prevent increasing noise
level and vibration.
2. Determine the air outlet direction
where the discharged air is not
blocked. In the case that the
installation place is exposed to
strong wind such as a seaside,
make sure the fan operating
properly by putting the unit
lengthwise along the wall or using
a dust or shield plates.
3. Specially in windy area, install the
unit to prevent the admission of
wind. If need suspending
installation, the installation bracket
should accord with technique
requirement in the installation
bracket diagram.
4. The installation wall should be solid
brick, concrete or the same
intensity construction, or actions to
reinforce, damping supporting
should be taken. The connection
between bracket and wall, bracket
and the air conditioner should be
firm, stable and reliable.
5. Be sure there is no obstacle which
block radiating air.
Strong wind
refrigerant pipe connection electrolux 18
17 electrolux outdoor unit installation
Refrigerant pipe connection
A
Settlement of outdoor unit
Anchor the outdoor unit with
a bolt and nut 10 or 8 tightly
and horizontally on a concrete
or rigid mount.
Flaring work
Air inlet
B
Main cause for refrigerant leakage is
due to defect in the flaring work.
Carry out correct flaring work using
the following procedure:
Air
inlet
Air outlet
MODEL
A (mm)
B (mm)
700x535x235
458
250
685x430x260
460
276
780x540x250
549
276
760x590x285
530
290
820x600x345
523
340
845x695x335
560
335
895x860x330
590
333
Drain joint installation
Fit the seal into the drain elbow, then
insert the drain joint into the base pan
hole of outdoor unit, rotate 90 to
securely assemble them.
Connecting the drain joint with an
extension drain hose (Locally
purchased), in case of the water
draining off the outdoor unit during the
heating mode.
Base pan hole
of outdoor unit
Seal
+
Seal
=
Drain joint
Drain pipe
1. Cut the pipes and the cable.
A) Use the piping kit accessory or
pipes purchased locally.
B) Measure the distance between the
indoor and the outdoor unit.
C) Cut the pipes a little longer than
the measured distance.
D) Cut the cable 1.5m longer than the
pipe length.
2. Burr removal
A) Completely remove all burrs from
the cut cross section of pipe/tube.
B) Put the end of the copper
tube/pipe in a downward direction as
you remove burrs in order to avoid
dropping burrs into the tubing.
3. Putting nut on
A) Remove flare nuts attached to
indoor and outdoor unit, then put
them on pipe/tube having completed
burr removal.(not possible to put them
on after flaring work)
Pipe
Wrong
Correct
Oblique Roughness Burr
Pipe
Reamer
Point
down
Flare nut
Cooper tube
electrical work electrolux 20
19 electrolux refrigerant pipe connection
Electrical work
Electric safety regulations for the initial Installation
4. Flaring work
A) Firmly hold copper pipe in a die in
the dimension shown in the table
below.
OUTER
DIAMETER (mm)
Bar
Copper
pipe
Handle
A (mm)
Máx.
Mín.
6,35
1,3
0,7
9,53
1,6
1,0
12,70
1,8
1,0
16
2,4
2,2
Connection Adjustment
1. Align the pipes to be connected.
2. Unscrew the flare nut with your
fingers and then with a wrench and
screw wrench, as shown in the
following figure.
Yoke
Red arrow mark
Clamp
handle
Caution: Excessive torque can
break nut depending on installation
conditions.
1. If there is serious safety problem
about the power supply, the
technicians should refuse to install
the air conditioner and explain to
the client until the problem is
solved.
2. Power voltage should be in the
range of 90%~110%of rated
voltage.
3. The creepage protector and main
power switch with a 1.5 times
capacity of Max. Current of the unit
should be installed in power circuit.
4. Ensure the air conditioner is
grounded well.
MODEL
9000 Btu’s
12000 Btu’s
18000 Btu’s
Indoor unit
tubing
Flare
nut
24000 Btu’s
Pipings
5. According to the attached Electrical
Connection Diagram located on the
panel of the outdoor unit to connect
the wire.
6. All wiring must comply with local
and national electrical codes and be
installed by qualified and skilled
electricians.
7. An individual branch circuit and
single receptacle used only for this
air conditioner must be available.
See the following table for
suggested wire sizes and fuse
specifications:
POWER SUPPLY
INPUT RATED AMP
Switch / Fuse
CABLE
SIZE
220-240V~/ 50Hz
10A
1 mm²
16A
1,5 mm²
220-230V~/ 60Hz
220-240V~/ 50Hz
220-230V~/ 60Hz
220-240V~/ 50Hz
25A
2,5 mm²
220-230V~/ 60Hz
32A
> 2,5 mm²
Note: The supply voltage must be consistent with the rate voltage of the air conditioner.
OUTER
DIAMETER (mm)
TIGHTENING
TORQUE(cm)
ADDITIONAL TIGHTENING
TORQUE(cm)
6,35
1570 (160 kgf/cm)
1960 (200 kgf/cm)
9,53
2940 (300 kgf/cm)
3430 (350 kgf/cm)
12,70
4900 (500 kgf/cm)
5390 (550 kgf/cm)
16
7360 (750 kgf/cm)
7850 (800 kgf/cm)
electrical work electrolux 22
21 electrolux electrical work
Connect the cable to the indoor unit
1. The inside and outside connecting
cable can be connected without
removing the front grille.
2. Connecting cable between indoor unit
and outdoor unit shall be approved
polychloroprene sheathed flexible cord,
type designation H07RN-F or heavier
cord.
3. Lift the indoor unit panel up, remove
the electrical box cover by loosening
the screw.
4. Ensure the colour of wires of outdoor
unit and the terminal Nos. are the same
to the indoors respectively.
5. Wrap those cables not connected with
terminals with insulation tapes, so that
they will not touch any electrical
components. Secure the cable onto the
control board with the cord clamp.
Electrical box
cover
< 24000 Btu's
COOL MODELS
< 24000 Btu's
HEAT AND COOL MODELS
"Connector A" or "Connector B"
Wire connector of indoor unit
"Connector A" or "Connector B"
Wire connector of indoor unit
1 2(N) 3 4
1 2(N)
or
or
Cables
board
Cables
board
Cables
board
MODELS
24000 Btu's
"Connector A”
Wire connector of indoor unit
< 18000 btu's CABLE (Heat & Cool model)
< 18000 btu's CABLE (Cool model)
"Cable A"
Cable code
Cable code
or
"Cable B"
Cable code
40mm
10mm
40mm
10mm
> 18000 btu's CABLE (Heat & Cool model)
"Cable C”
Cable code
40mm
10mm
1 2(N) 3 4
1 2(N) 3 4
40mm
10mm
Cables
board
Cables
board
electrical work electrolux 24
23 electrolux electrical work
Connect the cable to the outdoor unit
1. Remove the electrical control board
cover from the outdoor unit by
loosening the screw.
2. Connect the cables to the terminals as
identified with their respective
matched numbers on the terminal
block of indoor and outdoor units.
3. To prevent the ingress of water, from a
loop of the connective cable as
illustrated in the installation diagram of
indoor and outdoor units.
4. Insulate unused cords (conductors)
with PVC-tape.Process them so they
do not touch any electrical or metal
parts.
Cover
< 24000 Btu's
COOL MODEL
< 24000 Btu's
HEAT & COOL MODEL
"Connector A" or "Connector B"
Wire connector of outdoor unit
"Connector A" or "Connector B"
Wire connector of outdoor unit
Screw
1
1
2(N)
or
2(N) 3
or
4
Cables
board
Cables
board
1 2(N) 3
"Cable D”
Cable code
or
"Cable E”
Cable code
40mm
10mm
40mm
10mm
40mm
MODELS
24000 Btu's
"Connector A"
Wire connector of outdoor unit
10mm
> 18000 btu's CABLE (Heat & Cool model)
"Cable F”
Cable code
40mm
10mm
4
Cables
board
"Connector C” or "Connector D”
Wire connector of outdoor unit
< 18000 btu's CABLE (Heat & Cool model)
Código del cable
2(N) 3
Cables
board
4
Cables
board
< 18000 btu's CABLE (Cool model)
1
1 2(N)
Cables
board
or
1 2(N) 3
4
Cables
board
electrical work electrolux 26
25 electrolux electrical work
Caution
After the confirmation of the above conditions, prepare the wiring as follows:
1. Never fail to have an individual power circuit specifically for the air
conditioner. As for the method of wiring, be guided by the circuit diagram
posted on the inside of control cover.
2. The screw which fasten the wiring in the casing of electrical fittings are
liable to come loose from vibrations to which the unit is subjected during
the course of transportation. Check them and make sure that they are all
tightly fastened. (If they are loose, it could cause burn-out of the wires.)
3. Specification of power source.
4. Confirm that electrical capacity is sufficient.
5. See to that the starting voltage is maintained at more than 90 percent of the
rated voltage marked on the name plate.
6. Confirm that the cable thickness is as specified in the power source
specification.
7. Always install an earth leakage circuit breaker in a wet or moist area.
8. The following would be caused by voltage drop. Vibration of a magnetic
switch, which will damage the contact point, fuse breaking, disturbance of
the normal function of the overload.
9. The means for disconnection from a power supply shall be incorporated in
the fixed wiring and have an air gap contact separation of at least 3mm in
each active (phase) conductors.
Air purging with vacuum pump
1. Check that each tube(both liquid and gas side tubes) between the indoor
and outdoor units have been properly connected and all wiring for the test
run has been completed. Remove the service valve caps from both the gas
and the liquid side on the outdoor unit. Note that both the liquid and the gas
side service valves on the outdoor unit are kept closed at this stage.
2. When relocate the unit to another place, perform evacuation using vacuum
pump.
3. Pipe length and refrigerant amount:
Additional amount of
refrigerant to be charged
Connective
pipe length
Air purging
metod
Less than 5 m
Use vacuum pump.
5~10 m
Use vacuum pump.
Liquid side: Ö6.35
(Pipe lenght) x 30g
Caution in handling the packed valve
1. Open the valve stem until it hits against the stopper. Do not try to open it
further.
2. Securely tighten the valve stem cap with a spanner or the like. Valve stem
cap tightening torque (See Tightening torque table in page 19).
Air purging
Air and moisture in the refrigerant system have undesirable effects as
indicated below:
1. Pressure in the system rises.
2. Operating current rises.
3. Cooling or heating efficiency
drops.
4. Moisture in the refrigerant circuit
may freeze and block capillary
tubing.
5. Water may lead to corrosion of
parts in the refrigeration system.
6. Therefore, the indoor unit and
tubing between the indoor and
outdoor unit must be leak tested
and evacuated to remove any
noncondensables and moisture
from the system.
Refrigerant
Outdoor unit
A
Flare nut
Indoor unit
Gas
Stopper
C
Cap
D
B
Packed valve
Half union
Valve body
Valve stem
electrical safety electrolux 28
27 electrolux electrical work
Electrical safety
Perform the electric safe check after completing installation:
When using the vacuum pump
For method of using a manifold valve, refer to its operation manual.
1. Completely tighten the flare nuts,
A, B, C, D, connect the manifold
valve charge hose to a charge port
of the low-pressure valve on the
gas pipe side.
2. Connect the charge hose
connection to the vacuum pump.
3. Fully open the handle Lo of the
manifold valve.
4. Operate the vacuum pump to
evacuate. After starting
evacuation, slightly loose the flare
nut of the Lo valve on the gas pipe
side and check that the air is
entering (Operation noise of the
vacuum pump changes and a
compound meter indicates 0
instead of minus)
5. After the evacuation is complete,
fully close the handle Lo of the
manifold valve and stop the
operation of the vacuum pump.
Make evacuation for 15 minutes or
more and check that the
compound meter indicates 76cmHg (-1x10 Pa).
6. Turn the stem of the packed valve
B about 45o counterclockwise for
6~7 seconds after the gas coming
out, then tighten the flare nut
again. Make sure the pressure
display in the pressure indicator is
a little higher than the atmosphere
pressure.
7. Remove the charge hose from the
Low pressure charge hose.
8. Fully open the packed valve stems
B and A.
9. Securely tighten the cap of the
packed valve.
1. Insulated resistance: The insulated resistance must be more than 2M .
2. Grounding work: After finishing grounding work, measure the grounding
resistance by visual detection and grounding resistance tester. Make sure the
grounding resistance is less than 4 .
3. Electrical leakage check (performing during test running): During test
operation after finishing installation, the serviceman can use the electroprobe
and multimeter to perform the electrical leakage check. Turn off the unit
immediately if leakage happens. Check and find out the solution ways till the
unit operate properly.
Indoor unit
Gas leak check
Outdoor unit
Manifold valve
-76cm/Hg
Handle Lo
Charge
hose
Handle Hi
Charge hose
Vacuum pump
Soap water method
Apply a soap water or a liquid neutral
detergent on the indoor unit
connection or outdoor unit
connections by a soft brush to check
for leakage of the connecting points
of th piping. If bubbles come out, the
pipes have leakage.
Leak detector
Use the leak detector to check for
leakage.
Caution
A: Lo packed valve, B: Hi packed
valve C and D are ends of indoor unit
connection.
indoor unit
check point
Cover
Outdoor unit
check point
29 electrolux operation test
preparing the device for operation electrolux 30
Operation test
Preparing the device for operation
Perform test operation after completing gas leak check at the flare nut
connections and electrical safety check.
1. Contact a specialist to install the device.
2. Guarantee that the unit is appropriately fastened and complies with all of
the aforementioned safety norms.
3. Before operating the air conditioner, ensure that the air filter is installed
correctly.
4. If the unit has been out of use for a long period of time, it is recommended
that the air filter be cleaned before use. During continuous use, clean the air
filter every two weeks.
5. This air conditioner was designed for use under the following conditions:
1. Connect the power, press the
ON/OFF button on the remote
controller to turn the unit on.
2. Use the MODE button to select
COOL, HEAT, AUTO and FAN to
check if all the functions works
well.
3. When the ambient temperature is
too low(lower than 17ºC), the unit
cannot be controlled by the remote
controller to run at cooling mode,
manual operation can be taken.
Manual operation is used only when
the remote controller is disable or
maintenance necessary.
MODE
Cool
Heat
Deshumidifier
Room Temperature
Room Temperature
Room Temperature
Indoor
Outdoor*
Indoor
Outdoor
Indoor
Outdoor
17°C~32°C 18°C~43°C 17°C~30°C -7°C~24°C 17°C~32°C 11°C~43°C
* (-5°C~43°C cooling only)
Auto/Cool
or
Manual control button
Manual control
button
Auto
Cool
If air conditioner is used outside of the above conditions, certain safety protection
features may come into operation and cause the unit to function abnormally.
Room relative humidity less than 80%. If the air conditioner operates in excess of
this figure, the surface of the air conditioner may attract condensation. Please
sets the vertical air flow louver to its maximum angle (vertically to the floor), and
set HIGH fan mode.
Optimum performance will be achieved within these operating temperature.
product description electrolux 32
31 electrolux product description
Product description
Display panel
(indoor unit)
1 Front panel frame
2 Front panel
13 DEFROST*: Displayed when the
3 Air filter
4
5
6
7
8
9
air conditioner starts defrosting
automatically or when the warm air
control feature is activated in
heating operation.
(inside front panel)
Horizontal airflow grille
Vertical airflow grille
Temperature sensor
(inside front panel)
Panel
Infra-red signal receiver
Drain hose connector and
refrigerant gas connector
Remote control
10
11 Connector cable
12 Detection valve
13 Drain hose and refrigerant
*Nota: For Heating & Cooling model
only.
14 OPERATION: Displayed when the
air conditioner is in operation.
Air inlet
3
2
88
15 TURBO: Displayed when select
1
TURBO function on cooling
operation or on heating
operation(available for the type
adopts PTC in the indoor unit only).
4
connecting pipe
13
14
15
16
17 18
19
20
16 DIGITAL DISPLAY: Displays the
5
Air outlet
8
current setting temperature when
the air conditioner is in operation.
7
6
17 AUTO: Displayed during Auto
operation.
10
13
18 TIMER: Displayed during Timer
operation.
Air inlet
19 CLEAN AIR (optional): Displayed
when CLEAN AIR feature is
activated.
20 Signal receptor.
11
All the pictures in this manual are for
explanation purpose only. They may be
slightly different from the air conditioner
you purchased.
9
Air outlet
12
Outdoor unit
The description in the control is based
on a typical model. The functions are
the same in your air conditioner, even if
there are some differences in the
appearance.
remote control electrolux 34
33 electrolux remote control
Remote control
Remote control operation
When should the batteries be
replaced
1. When there is not a “beep”
anymore from the indoor unit
when using the control remote or
the signal light indicator does not
lit.
2. The indoor unit does not respond
to the remote control commands
to activate the programs.
1. Operation mode: Cool, Heat (Only for
the models with cool/heat), DRY, FAN,
and AUTO (Automatic).
2. Timer 24 hrs.
3. Internal temperature range selection:
17º - 30º.
4. LCD
5. Night light operation mode.
REMOTE CONTROLLER SPECIFICATIONS
Rated voltage
3V
Lowest of voltage of CPU emiting signal
2,0 V
Transmission distance
8 m*
Environment
-5ºC ~ 60ºC
* (with 3 V, it reaches 11 m)
1. The air conditioner will not operate when curtains, doors or other materials
block the signals between the remote control and the indoor unit.
2. Avoid spilling any liquid in the remote control. Do not expose to sunlight or
any heat source.
3. If the infrared signal receiver in the indoor unit is exposed to sunlight, the air
conditioner unit might not work properly. Use curtains or shades to avoid
having sunlight directly to the receiver.
4. If other electrical equipment react to the signals sent by the remote control,
change the position or consult with you local sales department.
Remote control battery
To use the remote control, it is necessary to install two (R03/Ir03x2) alkaline
AAA batteries.
To replace batteries
1. Slide out the battery
compartment cover ( located in
the back part of the remote
control).
2. Install the two AAA batteries in
the compartment (indicated in the
drawing located inside the
compartment).
3. Slide in the cover.
4. If the remote control is not
operated for long period of times,
batteries should be discarded.
Remote control instructions
1. The signal reach distance of the
remote control to the receiver that
is inside the main unit of the air
conditioner is 8 meters. Any
obstruction placed between the
receiver and the remote control
can cause interference, limiting
the capacity of the programming.
2. Any time that a button is pressed
in the remote control, the air
conditioner emits a “beep” that
indicates that a command has
been received and transmitted in the
indoor unit.
3. When selecting the function of
timer, the remote control sends
(automatically) a signal to the indoor
unit at the specific moment. If the
control remote is left in a position
that the signal is blocked, a 15
minute delay can be produced.
1. When replacing batteries, do not
use old batteries or a different type
battery. This may cause the remote
control to malfunction.
2. If you do not use the remote
controller for several weeks remove
the batteries. Otherwise battery
leakage may damage the remote
controller.
3. The average battery life under
normal use is about 6 months.
4. Replace the batteries when there is
no answering beep from the indoor
unit or if the Transmission Indicator
light fails to light.
remote control description electrolux 36
35 electrolux remote control description
Remote control description
1
ON/OFF: Push this button to start
operation, push the button again to
stop operation.
2 MODE: Each time you push the
button, a mode is selected in a
sequence that goes from AUTO,
COOL*, DRY, HEAT and FAN, as the
following figure indicates:
AUTO
COOL
DRY
HEAT*
FAN
* Note: Only for heating and cooling
models.
3 SWING: Push this button, the
louver would swing up and down
automatically. Push again to stop it.
4 SLEEP: Press this button to go into
the Energy-Saving operation mode.
Press it again to cancel. This
function is only can be used on
COOL, HEAT and AUTO mode and
maintain the most comfortable
temperature for you.
Note: While the unit is running
under SLEEP operation mode, it
would be canceled if you press the
other button.
(on some
5 FOLLOW ME
models): Push this button to initiate
the Follow Me feature, the remote
display is actual temperature at its
location. The remote control will
send this signal to the air
conditioner every 3 minutes interval
until press the Follow Me button
again. The air conditioner will beep
to indicate the Follow Me feature
has ended if it does not receive the
signal during any 7 minute interval.
DIRECTION: Press this button to
change the swing angle of the
louver. The swing angle of the
louver is 6o for each press. When
the louver swing at a certain
angle which would affect the
cooling and heating effect of the
air conditioner, it would
automatically change the swing
direction . No symbol will appear
in the display area when press
this button.
7 RESET: When you press the
recessed RESET button, all
current settings are cancelled and
the control will return to the initial
settings.
8 TEMP/TIME: Push the
button to increase the indoor
temperature setting or to adjust
the TIMER in a clockwise
direction. Push
the button to
decrease the indoor temperature
setting or to adjust the TIMER in
a counter-clockwise direction.
9 FAN SPEED: Used to select the
Fan Speed in four steps- AUTO,
LOW, MED or HIGH. Each time
the button is pressed, the fan
speed mode is shifted.
6
1
8
2
9
3
10
4
11
5
12
6
13
7
14
15
AUTO
LOW
MED
HIGH
10 TIMER: This button is used to
preset the time ON(start to
operate) and the time OFF(turn off
the operation).
1
8
2
9
3
10
4
11
5
12
6
13
7
14
15
lcd display indicators electrolux 38
37 electrolux remote control description
LCD display indicators
11 CANCEL: Push this button to
cancel the TIMER ON/OFF
settings.
12 TURBO*: Push this button on
COOL mode, the air conditioner
goes into powerful cooling
operation. Push again to cancel
the TURBO function.
*Note: Only for some models.
13 LED: Press this button to clear
the digit display in the air
conditioner, press it again to
activate it.
14 CLOCK: Use to set the time.
15 LOCK: When you press the
LOCK button, all current settings
are locked in and the remote
controller does not accept any
operation except that of the
LOCK. Press again to cancel the
LOCK mode.
1
2
1
8
2
9
3
10
4
11
5
12
6
13
7
14
15
TRANSMISSION INDICATOR: This
transmission indicator lights when
remote controller transmits signals
to the indoor unit.
1
MODE: Displays the current
operation mode. Including
AUTO(
), COOL( ), DRY( ),
HEAT*( ) , FAN ONLY ( )and back
to AUTO.
7
*Note: Not applicable to cooling
only models.
8
3
ON/OFF: Displayed by pressing the
ON/OFF button. Press the ON/OFF
button again to remove.
4
TIMER: Indicate Timer on/off time(0
23:50 hours) or clock time. The
clock time is indicated only when
no AUTO-ON/OFF timer is set.
When AUTOTIMER feature is
operating, it displays the AUTOON/OFF time. To check the current
time, press the CLOCK button, and
the time will display.
5
TEMPERATURE: Displays the
temperature setting (17ºC to 30ºC
When you set the operating mode
to FAN ONLY, no temperature
setting is displayed.
6
LOCK: Displayed by pressing the
LOCK button. Press the LOCK
button again to remove.
2
3
4
5
6
ATTENTION: All displays on the remote
controller are shown for illustration purposes
only.
7 SLEEP: Displayed by pressing the
SLEEP button. Press the SLEEP
button again to remove.
8 FAN SPEED: Displays the
selected fan speed, AUTO(no
display) and three fan speed levels
"
" (LOW) "
" (MED) and
"
“ (HIGH) can be
indicated.
39 electrolux clock adjustment
how the air conditioner works electrolux 40
Clock adjustment
How the air conditioner works
Before you start operating the air conditioner, set the clock of the remote
controller using the procedures given in this section. The clock panel on the
remote controller will display the time regardless of whether the air conditioner
is in use or not.
Automatic operation
When the Air Conditioner is ready for use, switch on the power and the
OPERATION indicator lamp on the display panel of the indoor unit starts
flashing.
1. Use the MODE .select button to select AUTO.
2. Push the TEMP button to set the desired room temperature. The most
comfortable temperature setting are between 21ºC o to 28ºC.
3. Push the ON/OFF button to start the air conditioner. The OPERATION lamp
on the display panel of the indoor unit lights. The
operating mode is AUTO FAN SPEED is automatically set and there are no
indicators shown on the display panel of the remote controller.
4. Push the ON/OFF button again to stop the unit operation.
Initial setting of the clock
1. After batteries are inserted in the
remote controller, the clock panel
will display "12:00" and begin to
1
flash.
2. Press
or
buttons to set
time.
3. Each time you press the button, the
time moves forward or backward
by one minute depending on which
side you press. The time alters as
quickly as you push the button.
4. Keep pressing the button without
releasing, the time moves forward
or backward by 10 minutes
depending on which side you
press.
5. When the right time is achieved,
press the CLOCK button or release
the
or
and wait for 5
1. The time of the CLOCK must be set
seconds, the clock time stops
before the AUTO-TIMER feature will
flashing and the clock starts
operate.
The CLOCK time can not
operating.
be adjusted after setting the AUTOON/OFF timer.
Readjusting the clock
2.
Clock accuracy is within 15
1. Press the CLOCK button on the
seconds per day.
remote controller for about 3
seconds, the colon in the clock
3. Static electricity or other factors (in
display will start to flash. To set the
case of extremely high voltage) can
new time, follow 2 and 5 of "Initial
cause remote controller clock
Setting of the clock".
initialize. If your remote controller is
initialized (flashing "12:00"), readjust
the clock before you start operation.
1. When you set the air conditioner in AUTO mode, it will automatically select cooling,
heating(cooling/heating models only), or fan only operation depending on what
temperature you have selected and the room temperature.
2. The air conditioner will control room temperature automatically round the temperature
point set by you.
3. If the AUTO mode is uncomfortable, you can select desired conditions manually.
COOL / HEAT and FAN ONLY operation
1. If the AUTO mode is not comfortable, you may manually override the settings
by using COOL, HEAT* or FAN** ONLY modes.
2. Push the TEMP button to set the desired room temperature. When in COOL
mode, the most comfortable settings are 21ºC or above. When in HEAT
mode, the most comfortable settings are 28 C or b elow.
3. Push the FAN SPEED to select the FAN mode of AUTO, HIGH, MED or LOW.
4. Push the ON/OFF button, the operation lamp lights and the air conditioner
start to operate as your settings. Push the ON/OFF button again to stop this
unit operation.
* Nota: Only for heating and cooling models
**Note: The FAN ONLY mode can not be used to control the temperature.
While in this mode, only steps 1,3 and 4 may be performed.
how the air conditioner works electrolux 42
41 electrolux how the air conditioner works
SLEEP mode
Press the sleep button to activate the
sleep mode. To deactivate, press the
button again.
Cool only mode:
Time
Set temperature
DRY Function
1 °C
Set
temperature
• After and hour of operation, the
adjusted temperature will increase
1º C. After, the unit keeps
operating 2ºC above the adjusted
temperature.
1 hour
1 hour
SLEEP FUNCTION (Cooling mode)
• The indoor unit fan operates at a
low velocity.
• After and hour of operation, the
adjusted temperature will decrease
1º C. After, the unit keeps
operating 2º C below the adjusted
temperature.
1 °C
Set
temperature
Room
temperature
Sleep function is only availaible in the
Cool/Heat and AUTO mode.
• The indoor unit fan operates at a
low velocity.
In heating mode (some models):
Co
ol
on
ly
Fa
n
Co
ol
Fa
n
on
ly
Due to the difference of the set
temperature of the unit and the
actual indoor temperature, the Air
Conditioner when in DRY mode will
automatically operate many times
without running the COOL and FAN
mode.
Co
ol
DRY operation
The dry mode will automatically select
the drying operation based on the
difference between the set
temperature and the actual room
temperature.
The temperature is regulated while
dehumidifying by repeating turning on
and off of the cooling operation or fan
only. The fan speed is LOW.
1. Push the MODE button to select
DRY.
2. Push the TEMP button to set the
desired temperature from 21ºC to
28ºC.
3. Push the ON/OFF button, the
operation lamp lights and the air
conditioner start to operate in the
DRY mode. FAN SPEED is Low.
Push the ON/OFF button again to
stop this unit operation.
1 °C
1 °C
1 hour
Air flow direction adjustment
Use SWING to adjust the airflow direction up and down.
1. When swing is pressed the horizontal louver moves up and down
automatically. Press again to stop operation
If the louver oscillates or moves in a position that could affect the cooling or
heating of the air conditioner the direction of the oscillation/movement would
alter automatically.
1 hour
7 hours
SLEEP FUNCTION (Heating mode)
Timer operation
1. Press the TIMER button as required. The current timer setting is displayed
alongside either the TIMER ON or TIMER OFF indicator, and will flash.
2. Press or to set the desired time. Each time you push the button, the time
moves forward or backward by 10 minutes depending on which direction you
press. The time alters as quickly as you press the button.
3. After setting the timer for TIMER ON and TIMER OFF, check the TIMER
indicator on the display panel of the indoor unit is illuminated.
4. After the timer has been set, there will be a half a second delay before the
remote control sends the signal to the air conditioner. Approximately 2
how to use the indoor unit electrolux 44
43 electrolux how the air conditioner works
How to use the indoor unit
seconds after, the adjusted temperature will be displayed.
5. The time of on and off in the air conditioner is has been set.
Canceling
Cancel button (CANCEL) Press the CANCEL button to cancel the timer setting.
When you select the timer operation, the remote controller automatically
transmits the timer signal to the indoor unit at the specified time.
Therefore, keep the remote controller in a location from which it can transmit
the signal to the indoor unit properly. The effective operation time set by remote
controller is limited in 24 hours.
Optimal operation
To achieve optimal performance, please note the following:
1. Adjust the air flow direction correctly so that it is not directed on people.
2. Adjust the temperature to achieve the highest comfort level. Do not adjust
the unit to excessive temperature levels.
3. Close doors and windows on COOL or HEAT modes, or performance may be
reduced.
4. Use TIMER ON button on the remote controller to select a time you want to
start your air conditioner.
5. Do not put any object near air inlet or air outlet, as the efficiency of the air
conditioner may be reduced and the air conditioner may stop running.
6. Clean the air filter periodically, otherwise cooling or heating performance
may be reduced.
7. Do not operate unit with horizontal louvre in closed position.
Adjusting air flow direction
Adjust the air flow direction properly
otherwise, it might cause discomfort
or cause uneven room temperatures.
Adjust the horizontal louver using the
remote controller. Adjust the vertical
louver manually.
Adjusting the vertical air flow
direction (up - down)
The air conditioner automatically
adjusts the vertical air flow direction in
accordance with the operating mode.
To set the horizontal air flow
direction (left/ right)
Adjust the vertical louver manually
using the lever on the left or right side
of the vertical louver arm (Depending
on model). Take care not to catch
fingers on the fan, horizontal louver or
to damage vertical louvers. When the
air conditioner is in operation and the
horizontal louver is in a specific
position, move the lever at left (or
right, depending on model) end of the
air outlet to the desired position.
To automatically swing the air flow
direction (up/down)
Perform this function while the air
conditioner is in operation.
Lever
45 electrolux how to use the indoor unit
manual operation (without remote control) electrolux 46
Manual operation (without remote control)
Press the SWING button on the remote
controller.
To stop the function, press the SWING
button again.
Press AIR DIRECTION button to lock
louver in desired position.
The AIR DIRECTION and SWING buttons
will be disabled when the air conditioner is
not in operation (including when the
TIMER ON is set).
Do not operate the air conditioner for long
periods with the air flow direction set
downward in cooling or dry mode.
Otherwise, condensation may occur on
the surface of the horizontal louver
causing moisture to drop on to the floor or
on furnishings.
Do not move the horizontal louver
manually. Always use the AIR DIRECTION
or SWING button. If you move this louver
manually, it may malfunction during
operation. If the louver malfunctions, stop
the airconditioner once and restart it.
When the air conditioner is started
immediately after it was stopped, the
horizontal louver might not move for
approximately 10 seconds.
Open angle of the horizontal louver should
not be set too small, as COOLING or
HEATING performance may be impaired
due to too restricted air flow area.
Do not operate unit with horizontal louver
in closed position.
When the air conditioner is connected to
power (initial power), the horizontal louver
may generate a sound for 10 seconds,
this is a normal operation.
Manual operation can be used
temporarily in case you can not find
the remote controller or its batteries
are exhausted.
1. Open and lift the front panel up to
an angle until it remains fixed with
a clicking sound.
2. One press of the manual control
button will lead to the forced
AUTO operation.
3. Close the panel firmly to its
original position.
Manual control
button
Once you push the manual button,
the operation mode is shifted in an
order as: AUTO, COOL, OFF.
Push the button twice, the unit will
operate in forced COOL mode. This is
used for testing purposes only .
Third press will stop the operation
and turn off the air conditioner
operation.
To restore the remote controller
operation, use the remote controller
directly.
Auto/Cool
maintenance electrolux 48
47 electrolux maintenance
Maintenance
then dry.
6. Clean the support frame using a
vacuum cleaner or water. After, dry
for a couple of hours or until dry.
7. Insert the fresh air filter in its original
place.
8. Insert the high part of the air filter
(fresh air filter + Support frame)
again in the unit keeping in mind that
the outside border (right and left) are
lined up correctly, now place the
whole filter in the initial position.
Cleaning the indoor unit and remote
controller
1. It is necessary to stop the air
conditioner and disconnect the
power supply before cleaning.
2. Use a dry cloth to wipe the indoor
unit and remote controller.
3. A cloth dampened with cold water
may be used on the indoor unit if it is
very dirty.
4. The front panel of the indoor unit can
be removed and cleaned with water.
Then wipe it with a dry cloth.
5. Do not use a chemically treated cloth
or duster to clean the unit.
6. Do not use benzine, thinner,
polishing powder, or similar solvents
for cleaning. These may cause the
plastic surface to crack or deform.
Filtro
refrescante
de aire
Fig.1
Soporte del marco
Fig.2
Filtro
refrescante
de aire
Soporte
del marco
Filtro
refrescante
de aire
Fig.3
Soporte del marco
Fig.4
Fig.5
Cleaning the air filter
A clogged air filter reduces the cooling
efficiency of this unit. Please clean the
filter once every 2 weeks.
1. Lift the indoor unit panel up to an
angle until it stops with a clicking
sound.2. Take hold of the handle of
the air filter and lift it up slightly to
take it out from the filter holder, then
pull it downwards.
3. Remove the air filter (Fresh air filter +
support) of the unit.
4. Remove fresh air filter from frame
support.
5. Clean the fresh air filter at least once
a month, and replace every 4 to 5
months. Use a vacuum cleaner,
filtro de aire
Maintenance
If you plan to idle the unit for a long time, perform the following:
1. Operate the fan for about half a day to dry the inside of the unit.
2. Stop the air conditioner and disconnect power. Remove the batteries from
the remote controller.
3. The outdoor unit requires periodic maintenance and cleaning. Do not attempt
to do this yourself. Contact your dealer or servicer.
Checks before operation
1. Check that the wiring is not broken off or disconnected.
2. Check that the air filter is installed
3. Check if the air outlet or inlet is blocked after the air conditioner has not been
used for a long time.
filtro de aire
49 electrolux operation tips
operation tips electrolux 50
Operation tips
The following events may occur during normal operation.
Protection of the air conditioner.
Compressor protection
The compressor can't restart for 3 minutes after it stops.
Anti-cold air (Cooling and heating models only)
The unit is designed not to blow cold air on HEAT mode, when the indoor heat
exchanger is in one of the following three situations and the set temperature has
not been reached.
1. When heating has just starting.
2. Defrosting.
3. Low temperature heating.
Defrosting (Cooling and heating models only)
Frost may be generated on the outdoor unit during heat cycle when outdoor
temperature is low and humidity is high resulting in lower heating efficiency of
the air conditioner. During this condition air conditioner will stop heating
operation and start defrosting automatically.
The time to defrost may vary from 4 to 10 minutes according to the outdoor
temperature and the amount of frost buildup on the outdoor unit.
The indoor or outdoor fan stop running when defrosting (Cooling and heating
models only).
A white mist coming out from the indoor unit
A white mist may generate due to a large temperature difference between air
inlet and air outlet on COOL mode in an indoor environment that has a high
relative humidity.
A white mist may generate due to moisture generated from defrosting process
when the air conditioner restarts in HEAT mode operation after defrosting.
Low noise of the air conditioner
You may hear a low hissing sound when the compressor is running or has just
stopped running.
This sound is the sound of the refrigerant flowing or coming to a stop.
You can also hear a low "squeak" sound when the compressor is running or has
just stopped running. This is caused by heat expansion and cold contraction of
the plastic parts in the unit when the temperature is changing.
A noise may be heard due to louver restoring to its original position when power
is first turned on.
Dust is blown out from the indoor unit.
This is a normal condition when the air conditioner has not been used for a long
time or during first use of the unit.
A peculiar smell comes out from the indoor unit.
This is caused by the indoor unit giving off smells permeated from building
material, from furniture, or smoke.
The air conditioner turns to FAN only mode from COOL or HEAT (For
cooling and heating models only) mode.
When indoor temperature reaches the temperature setting on air conditioner, the
compressor will stop automatically, and the air conditioner turns to FAN only
mode. The compressor will start again when the indoor temperature rises on
COOL mode or falls on HEAT mode (For cooling and heating models o ly) to the
set point.
Dripping water may generate on the surface of the indoor unit when cooling in a
high relatively humidity (relative humidity higher than 80%). Adjust the horizontal
louver to the maximum air outlet position and select HIGH fan speed.
Heating mode (For cooling and heating models only)
The air conditioner draws in heat from the outdoor unit and releases it via the
indoor unit during heating operation. When the outdoor temperature falls, heat
drawn in by the air conditioner decreases accordingly. At the same time, heat
loading of the air conditioner increases due to larger difference between indoor
and outdoor temperature. If a comfortable temperature can't be achieved by the
air conditioner, we suggest you use a supplementary heating device.
Auto-restart function
Power failure during operation will stop the unit completely.
For the unit without Auto-restart feature, when the power restores, the
OPERATION indicator on the indoor unit starts flashing. To restart the operation,
push the ON/OFF button on the remote controller. For the unit with Auto-restart
feature, when the power restores, the unit restarts automatically with all the
previous settings preserved by the memory function.
Lightning or a car wireless telephone operating nearby may cause the unit
to malfunction.
Disconnect the unit with power and then re-connect the unit with power again.
Push the ON/OFF button on the remote controller to restart operation.
technical specifications electrolux 52
51 electrolux solutions for problems
Solutions for problems
Technical specifications
If your air conditioner malfunctions, check the following information to find
solutions or probable causes of the failure. Do not try to repair the unit by
yourself, if these solutions do not solve the failures; call your local service repair
team.
COOL MODELS
Poor Equipment performance
1. The air outlet or inlet in the exterior part is obstructed.
2. The temperature in the exterior is high due to direct sunlight or another heat
source.
3. Heater or a cooking stove is being used in the same room.
4. Room is full of people.
5. The air filter is obstructed by dust or is dirty.
6. Inappropriate temperature adjustment.
7. Front part is obstructed.
8. The capacity of the equipment is not adequate for the size of the room.
9. Air conditioner was just turn on.
10.Windows or doors are open.
11.Motor protector has been activated.
The unit does not start
1. The plug is not connected to the outlet.
2. No electricity in the outlet.
3. The voltage is different.
4. Temperature is not adjusted properly.
5. burned fuse.
6. The remote control batteries need to be replaced.
7. wrong operation time.
Stop the air conditioner immediately if one of the following malfunctions occur
1. The operation indicator or other indicator flash(5 times per second) and the flashing is
not stop by disconnecting and connecting the unit.
2. Frequent change of fuses and malfunctions in the switch circuit.
3. Water spills over the equipment.
4. Remote control does not work.
5. Any other abnormal situation.
OUTDOOR UNIT
EASC09C2ASK*
EASC12C2ASK*
EASC18C2ASK*
EASC24C2ASK*
INDOOR UNIT
EASE09C2ASK*
EASE12C2ASK*
EASE18C2ASK*
EASE24C2ASK*
W,S,M
W,S,M
W,S,M
W,S,M
Cycle
Cool
Cool
Cool
Cool
Cooling power (Btu/h)
9000
12000
18000
24000
Heating power (Btu/h)
-
-
-
-
220
220
220
220
*Color (W=White;S=Silver;M=Mirror)
Rated voltage (V)
Frequency (Hz)
60
60
60
60
Indoor unit width (mm)
790
790
930
1036
315
Indoor unit high (mm)
275
275
275
Indoor unit depth (mm)
190
196
198
230
Indoor unit net weight (kg)
7,5
9
10
13,5
Outdoor unit width (mm)
700
700
780
820
Outdoor unit high (mm)
535
540
540
600
Outdoor unit depth (mm)
235
240
250
345
Outdoor unit net weight (kg)
21
24
36
40
notes electrolux 54
53 electrolux technical specifications
NOTES
HEAT & COOL MODELS
OUTDOOR UNIT
EASC09P5ASK*
EASC12P5ASK*
EASC18P5ASK*
EASC24P5ASK*
INDOOR UNIT
EASE09P5ASK*
EASE12P5ASK*
EASE18P5ASK*
EASE24P5ASK*
*Color (W=White;S=Silver;M=Mirror)
Cycle
W,S,M
W,S,M
W,S,M
W,S,M
Heat & Cool
Heat & Cool
Heat & Cool
Heat & Cool
Cooling power (Btu/h)
9000
12000
18000
24000
Heating power (Btu/h)
9000
12000
18000
24000
Rated voltage (V)
220
220
220
220
Frequency (Hz)
50
50
50
50
Indoor unit width (mm)
790
790
930
1036
Indoor unit high (mm)
275
275
275
315
Indoor unit depth (mm)
196
196
198
230
8
9
10
13
Indoor unit net weight (kg)
Outdoor unit width (mm)
685
700
780
820
Outdoor unit high (mm)
430
540
540
600
Outdoor unit depth (mm)
260
240
250
345
Outdoor unit net weight (kg)
22
24,5
33
44