Philips 32PFL3505D/F7 Service manual

32” LCD TV
chassis PL10.3
Service Manual
Contents
TYPE A
32PFL3505D/F7
PHILIPS
(Serial No.: DS1A, DS2A, DS3A, YA1A)
32PFL3515D/F7
PHILIPS
(Serial No.: YA1A)
PHILIPS
(Serial No.: DS4A)
PHILIPS
(Serial No.: DS8A, DS9A, YA2A, YA4A)
TYPE B
32PFL3505D/F7
TYPE C
32PFL3505D/F7
This service manual contains information of different types of models.
Make sure to refer to the section describing your model.
© 2010 Funai Electric Co., Ltd.
All rights reserved. No part of this manual may be reproduced, copied, transmitted, disseminated, transcribed,
downloaded or stored in any storage medium, in any form or for any purpose without the express prior written
consent of Funai. Furthermore, any unauthorized commercial distribution of this manual or any revision hereto
is strictly prohibited.
Information in this document is subject to change without notice. Funai reserves the right to change the content
herein without the obligation to notify any person or organization of such changes.
with the
design is a registered trademark of Funai Electric Co., Ltd and may not be used in any way
without the express written consent of Funai. All other trademarks used herein remain the exclusive property of
their respective owners. Nothing contained in this manual should be construed as granting, by implication or
otherwise, any license or right to use any of the trademarks displayed herein. Misuse of any trademarks or any
other content in this manual is strictly prohibited. Funai shall aggressively enforce its intellectual property rights
to the fullest extent of the law.
101202
IMPORTANT SAFETY NOTICE
Proper service and repair is important to the safe, reliable operation of all
P&F Equipment. The service procedures recommended by P&F and
described in this service manual are effective methods of performing
service operations. Some of these service special tools should be used
when and as recommended.
It is important to note that this service manual contains various CAUTIONS
and NOTICES which should be carefully read in order to minimize the risk
of personal injury to service personnel. The possibility exists that improper
service methods may damage the equipment. It also is important to
understand that these CAUTIONS and NOTICES ARE NOT EXHAUSTIVE.
P&F could not possibly know, evaluate and advice the service trade of all
conceivable ways in which service might be done or of the possible
hazardous consequences of each way. Consequently, P&F has not
undertaken any such broad evaluation. Accordingly, a servicer who uses a
service procedure or tool which is not recommended by P&F must first use
all precautions thoroughly so that neither his safety nor the safe operation
of the equipment will be jeopardized by the service method selected.
The LCD panel is manufactured to provide many years of useful life.
Occasionally a few non active pixels may appear as a tiny spec of color.
This is not to be considered a defect in the LCD screen.
TABLE OF CONTENTS
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
Important Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
Standard Notes for Servicing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
Cabinet Disassembly Instructions [TYPE A, TYPE B] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
[TYPE C] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6
Electrical Adjustment Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
How to Initialize the LCD TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1
Firmware Renewal Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1
Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1
Block Diagrams
[TYPE A] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-1
[TYPE B] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-7
[TYPE C] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-13
Schematic Diagrams / CBA and Test Points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-1
Waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-1
Wiring Diagram
[TYPE A, TYPE B] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-1
[TYPE C] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-2
Exploded Views. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-1
Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-1
Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-1
SPECIFICATIONS
< TUNER / NTSC >
ANT. Input ---------------------- 75 Ω Unbal., F type
Description
Condition
Unit
Nominal
Limit
---
MHz
±2.3
±2.1
TV.ch.4
CA.ch.31
CA.ch.87
dBµ
dBµ
dBµ
18
18
18
20
20
23
Condition
Unit
Nominal
Limit
---
kHz
---
±100
ch.4
ch.10
ch.41
dBm
dBm
dBm
-------
-76/0
-76/0
-76/+4
Description
Condition
Unit
Nominal
Limit
1. Native Pixel Resolution
Horizontal
Vertical
pixels
pixels
1366
768
-----
---
cd/m2
380
---
Horizontal
Vertical
°
°
-88 to 88
-88 to 88
-----
Condition
Unit
Nominal
Limit
Horizontal
Vertical
%
%
5
5
5±5
5±5
--x
y
°K
12000
0.272
0.278
--±3%
±3%
Horizontal
Vertical
line
line
400
350
-----
1. AFT Pull-In Range
2. Synchronizing Sens.
< TUNER / ATSC >
Description
1. Received Freq. Range (-28dBm)
2. ATSC Dynamic Range (min / max)
< LCD PANEL >
2. Brightness (w / filter)
3. Viewing Angle
< VIDEO >
Description
1. Over Scan
2. Color Temperature
3. Resolution (composite video)
< AUDIO >
All items are measured across 8 Ω load at speaker output terminal with L.P.F.
Description
1. Audio Output 10% Distortion
(ATSC 0 dBfs)
2. Audio Distortion (NTSC)
3. Audio Freq. Response (NTSC)
Condition
Unit
Nominal
Limit
Lch/Rch
W
10.0/10.0
8.0/8.0
500mW: Lch/Rch
%
0.5/0.5
2.0/2.0
-6dB: Lch
-6dB: Rch
Hz
Hz
70 to 10 k
70 to 10 k
-----
1-1
PL10.3SP
IMPORTANT SAFETY PRECAUTIONS
Prior to shipment from the factory, our products are strictly inspected for recognized product safety and electrical
codes of the countries in which they are to be sold. However, in order to maintain such compliance, it is equally
important to implement the following precautions when a set is being serviced.
Safety Precautions for LCD TV
Circuit
d. Leakage Current Hot Check - With the
instrument completely reassembled, plug the
AC line cord directly into a 120 V AC outlet. (Do
not use an isolation transformer during this
test.) Use a leakage current tester or a
metering system that complies with American
National Standards Institute (ANSI) C101.1
Leakage Current for Appliances and
Underwriters Laboratories (UL) 1410, (50.7).
With the instrument AC switch first in the on
position and then in the off position, measure
from a known earth ground (metal water pipe,
conduit, etc.) to all exposed metal parts of the
instrument (antennas, handle brackets, metal
cabinet, screw heads, metallic overlays, control
shafts, etc.), especially any exposed metal
parts that offer an electrical return path to the
chassis. Any current measured must not
exceed 0.5 milli-ampere. Reverse the
instrument power cord plug in the outlet and
repeat the test.
1. Before returning an instrument to the
customer, always make a safety check of the
entire instrument, including, but not limited to, the
following items:
a. Be sure that no built-in protective devices are
defective and have been defeated during
servicing. (1) Protective shields are provided
on this chassis to protect both the technician
and the customer. Correctly replace all missing
protective shields, including any removed for
servicing convenience. (2) When reinstalling
the chassis and/or other assembly in the
cabinet, be sure to put back in place all
protective devices, including but not limited to,
nonmetallic control knobs, insulating
fishpapers, adjustment and compartment
covers/shields, and isolation resistor/capacitor
networks. Do not operate this instrument or
permit it to be operated without all
protective devices correctly installed and
functioning. Servicers who defeat safety
features or fail to perform safety checks
may be liable for any resulting damage.
READING SHOULD
NOT BE ABOVE 0.5 mA
DEVICE
BEING
TESTED
b. Be sure that there are no cabinet openings
through which an adult or child might be able to
insert their fingers and contact a hazardous
voltage. Such openings include, but are not
limited to, (1) spacing between the Liquid
Crystal Panel and the cabinet mask, (2)
excessively wide cabinet ventilation slots, and
(3) an improperly fitted and/or incorrectly
secured cabinet back cover.
LEAKAGE
CURRENT
TESTER
_
+
TEST ALL EXPOSED
METAL SURFACES
ALSO TEST WITH
PLUG REVERSED
USING AC
ADAPTER PLUG
AS REQUIRED
c. Antenna Cold Check - With the instrument AC
plug removed from any AC source, connect an
electrical jumper across the two AC plug
prongs. Place the instrument AC switch in the
on position. Connect one lead of an ohmmeter
to the AC plug prongs tied together and touch
the other ohmmeter lead in turn to each tuner
antenna input exposed terminal screw and, if
applicable, to the coaxial connector. If the
measured resistance is less than 1.0 megohm
or greater than 5.2 megohm, an abnormality
exists that must be corrected before the
instrument is returned to the customer. Repeat
this test with the instrument AC switch in the off
position.
EARTH
GROUND
ANY MEASUREMENTS NOT WITHIN THE
LIMITS SPECIFIED HEREIN INDICATE A
POTENTIAL SHOCK HAZARD THAT MUST
BE ELIMINATED BEFORE RETURNING THE
INSTRUMENT TO THE CUSTOMER OR
BEFORE CONNECTING THE ANTENNA OR
ACCESSORIES.
2. Read and comply with all caution and safetyrelated notes on or inside the receiver cabinet, on
the receiver chassis, or on the Liquid Crystal
Panel.
2-1
LTVN_ISP
7. Product Safety Notice - Some electrical and
mechanical parts have special safety-related
characteristics which are often not evident from
visual inspection, nor can the protection they give
necessarily be obtained by replacing them with
components rated for higher voltage, wattage, etc.
Parts that have special safety characteristics are
identified by a # on schematics and in parts lists.
Use of a substitute replacement that does not
have the same safety characteristics as the
recommended replacement part might create
shock, fire, and/or other hazards. The product's
safety is under review continuously and new
instructions are issued whenever appropriate.
Prior to shipment from the factory, our products
are strictly inspected to confirm they comply with
the recognized product safety and electrical codes
of the countries in which they are to be sold.
However, in order to maintain such compliance, it
is equally important to implement the following
precautions when a set is being serviced.
3. Design Alteration Warning - Do not alter or add
to the mechanical or electrical design of this TV
receiver. Design alterations and additions,
including, but not limited to circuit modifications
and the addition of items such as auxiliary audio
and/or video output connections, might alter the
safety characteristics of this receiver and create a
hazard to the user. Any design alterations or
additions will void the manufacturer's warranty and
may make you, the servicer, responsible for
personal injury or property damage resulting
therefrom.
4. Hot Chassis Warning a. Some TV receiver chassis are electrically
connected directly to one conductor of the AC
power cord and maybe safety-serviced without
an isolation transformer only if the AC power
plug is inserted so that the chassis is
connected to the ground side of the AC power
source. To confirm that the AC power plug is
inserted correctly, with an AC voltmeter,
measure between the chassis and a known
earth ground. If a voltage reading in excess of
1.0 V is obtained, remove and reinsert the AC
power plug in the opposite polarity and again
measure the voltage potential between the
chassis and a known earth ground.
b. Some TV receiver chassis normally have 85V
AC(RMS) between chassis and earth ground
regardless of the AC plug polarity. This chassis
can be safety-serviced only with an isolation
transformer inserted in the power line between
the receiver and the AC power source, for both
personnel and test equipment protection.
c. Some TV receiver chassis have a secondary
ground system in addition to the main chassis
ground. This secondary ground system is not
isolated from the AC power line. The two
ground systems are electrically separated by
insulation material that must not be defeated or
altered.
5. Observe original lead dress. Take extra care to
assure correct lead dress in the following areas: a.
near sharp edges, b. near thermally hot parts-be
sure that leads and components do not touch
thermally hot parts, c. the AC supply, d. high
voltage, and, e. antenna wiring. Always inspect in
all areas for pinched, out of place, or frayed wiring.
Check AC power cord for damage.
6. Components, parts, and/or wiring that appear to
have overheated or are otherwise damaged
should be replaced with components, parts, or
wiring that meet original specifications.
Additionally, determine the cause of overheating
and/or damage and, if necessary, take corrective
action to remove any potential safety hazard.
2-2
LTVN_ISP
Precautions during Servicing
A. Parts identified by the # symbol are critical for
safety.
Replace only with part number specified.
B. In addition to safety, other parts and assemblies
are specified for conformance with regulations
applying to spurious radiation. These must also be
replaced only with specified replacements.
Examples: RF converters, RF cables, noise
blocking capacitors, and noise blocking filters, etc.
C. Use specified internal wiring. Note especially:
1) Wires covered with PVC tubing
2) Double insulated wires
3) High voltage leads
D. Use specified insulating materials for hazardous
live parts. Note especially:
1) Insulation Tape
2) PVC tubing
3) Spacers
4) Insulators for transistors.
E. When replacing AC primary side components
(transformers, power cord, etc.), wrap ends of
wires securely about the terminals before
soldering.
F. Observe that the wires do not contact heat
producing parts (heat sinks, oxide metal film
resistors, fusible resistors, etc.)
G. Check that replaced wires do not contact sharp
edged or pointed parts.
H. When a power cord has been replaced, check that
5~6 kg of force in any direction will not loosen it.
I.
Also check areas surrounding repaired locations.
J. Use care that foreign objects (screws, solder
droplets, etc.) do not remain inside the set.
K. When connecting or disconnecting the internal
connectors, first, disconnect the AC plug from the
AC supply outlet.
L. When installing parts or assembling the cabinet
parts, be sure to use the proper screws and
tighten certainly.
2-3
LTVN_ISP
Safety Check after Servicing
Examine the area surrounding the repaired location for damage or deterioration. Observe that screws, parts and
wires have been returned to original positions. Afterwards, perform the following tests and confirm the specified
values in order to verify compliance with safety standards.
1. Clearance Distance
When replacing primary circuit components, confirm
specified clearance distance (d) and (d') between
soldered terminals, and between terminals and
surrounding metallic parts. (See Fig. 1)
Chassis or Secondary Conductor
Primary Circuit
Table 1: Ratings for selected area
AC Line Voltage
Region
Clearance
Distance (d), (d’)
110 to 130 V
U.S.A. or
Canada
≥ 3.2 mm
(0.126 inches)
d'
d
Note: This table is unofficial and for reference only. Be
sure to confirm the precise values.
Fig. 1
2. Leakage Current Test
Confirm the specified (or lower) leakage current
between B (earth ground, power cord plug prongs) and
externally exposed accessible parts (RF terminals,
antenna terminals, video and audio input and output
terminals, microphone jacks, earphone jacks, etc.) is
lower than or equal to the specified value in the table
below.
Exposed Accessible Part
Z
AC Voltmeter
(High Impedance)
Measuring Method: (Power ON)
Insert load Z between B (earth ground, power cord plug
prongs) and exposed accessible parts. Use an AC
voltmeter to measure across both terminals of load Z.
See Fig. 2 and following table.
B
Earth Ground
Power Cord Plug Prongs
Fig. 2
Table 2: Leakage current ratings for selected areas
AC Line Voltage
Region
Load Z
Leakage Current (i)
Earth Ground (B) to:
110 to 130 V
U.S.A. or
Canada
0.15 µF CAP. & 1.5 kΩ
RES. Connected in parallel
i ≤ 0.5 mA rms
Exposed accessible
parts
Note: This table is unofficial and for reference only. Be sure to confirm the precise values.
2-4
LTVN_ISP
STANDARD NOTES FOR SERVICING
Circuit Board Indications
How to Remove / Install Flat Pack-IC
1. The output pin of the 3 pin Regulator ICs is
indicated as shown.
1. Removal
With Hot-Air Flat Pack-IC Desoldering Machine:
Top View
Out
1. Prepare the hot-air flat pack-IC desoldering
machine, then apply hot air to the Flat Pack-IC
(about 5 to 6 seconds). (Fig. S-1-1)
Bottom View
In
Input
2. For other ICs, pin 1 and every fifth pin are
indicated as shown.
5
Pin 1
10
3. The 1st pin of every male connector is indicated as
shown.
Fig. S-1-1
2. Remove the flat pack-IC with tweezers while
applying the hot air.
Pin 1
3. Bottom of the flat pack-IC is fixed with glue to the
CBA; when removing entire flat pack-IC, first apply
soldering iron to center of the flat pack-IC and heat
up. Then remove (glue will be melted). (Fig. S-1-6)
Pb (Lead) Free Solder
4. Release the flat pack-IC from the CBA using
tweezers. (Fig. S-1-6)
Pb free mark will be found on PCBs which use Pb
free solder. (Refer to figure.) For PCBs with Pb free
mark, be sure to use Pb free solder. For PCBs
without Pb free mark, use standard solder.
CAUTION:
1. The Flat Pack-IC shape may differ by models. Use
an appropriate hot-air flat pack-IC desoldering
machine, whose shape matches that of the Flat
Pack-IC.
2. Do not supply hot air to the chip parts around the
flat pack-IC for over 6 seconds because damage
to the chip parts may occur. Put masking tape
around the flat pack-IC to protect other parts from
damage. (Fig. S-1-2)
Pb free mark
3-1
TVN_SN
With Soldering Iron:
3. The flat pack-IC on the CBA is affixed with glue, so
be careful not to break or damage the foil of each
pin or the solder lands under the IC when
removing it.
CBA
1. Using desoldering braid, remove the solder from
all pins of the flat pack-IC. When you use solder
flux which is applied to all pins of the flat pack-IC,
you can remove it easily. (Fig. S-1-3)
Hot-air
Flat Pack-IC
Desoldering
Machine
Flat Pack-IC
Desoldering Braid
Soldering Iron
Masking
Tape
Tweezers
Flat Pack-IC
Fig. S-1-3
2. Lift each lead of the flat pack-IC upward one by
one, using a sharp pin or wire to which solder will
not adhere (iron wire). When heating the pins, use
a fine tip soldering iron or a hot air desoldering
machine. (Fig. S-1-4)
Fig. S-1-2
Sharp
Pin
Fine Tip
Soldering Iron
Fig. S-1-4
3. Bottom of the flat pack-IC is fixed with glue to the
CBA; when removing entire flat pack-IC, first apply
soldering iron to center of the flat pack-IC and heat
up. Then remove (glue will be melted). (Fig. S-1-6)
4. Release the flat pack-IC from the CBA using
tweezers. (Fig. S-1-6)
3-2
TVN_SN
With Iron Wire:
2. Installation
1. Using desoldering braid, remove the solder from
all pins of the flat pack-IC. When you use solder
flux which is applied to all pins of the flat pack-IC,
you can remove it easily. (Fig. S-1-3)
1. Using desoldering braid, remove the solder from
the foil of each pin of the flat pack-IC on the CBA
so you can install a replacement flat pack-IC more
easily.
2. Affix the wire to a workbench or solid mounting
point, as shown in Fig. S-1-5.
2. The “ I ” mark on the flat pack-IC indicates pin 1.
(See Fig. S-1-7.) Be sure this mark matches the
pin 1 on the PCB when positioning for installation.
Then presolder the four corners of the flat pack-IC.
(See Fig. S-1-8.)
3. While heating the pins using a fine tip soldering
iron or hot air blower, pull up the wire as the solder
melts so as to lift the IC leads from the CBA
contact pads as shown in Fig. S-1-5.
3. Solder all pins of the flat pack-IC. Be sure that
none of the pins have solder bridges.
4. Bottom of the flat pack-IC is fixed with glue to the
CBA; when removing entire flat pack-IC, first apply
soldering iron to center of the flat pack-IC and heat
up. Then remove (glue will be melted). (Fig. S-1-6)
Example :
5. Release the flat pack-IC from the CBA using
tweezers. (Fig. S-1-6)
Note: When using a soldering iron, care must be
taken to ensure that the flat pack-IC is not
being held by glue. When the flat pack-IC is
removed from the CBA, handle it gently
because it may be damaged if force is applied.
Pin 1 of the Flat Pack-IC
is indicated by a " " mark.
Hot Air Blower
or
Fig. S-1-7
Presolder
Iron Wire
Soldering Iron
To Solid
Mounting Point
Fig. S-1-5
Flat Pack-IC
CBA
CBA
Fig. S-1-8
Fine Tip
Soldering Iron
Flat Pack-IC
Tweezers
Fig. S-1-6
3-3
TVN_SN
Instructions for Handling Semiconductors
Electrostatic breakdown of the semi-conductors may
occur due to a potential difference caused by
electrostatic charge during unpacking or repair work.
1. Ground for Human Body
Be sure to wear a grounding band (1 MΩ) that is
properly grounded to remove any static electricity that
may be charged on the body.
2. Ground for Workbench
Be sure to place a conductive sheet or copper plate
with proper grounding (1 MΩ) on the workbench or
other surface, where the semi-conductors are to be
placed. Because the static electricity charge on
clothing will not escape through the body grounding
band, be careful to avoid contacting semi-conductors
with your clothing.
<Incorrect>
CBA
<Correct>
Grounding Band
1MΩ
CBA
1MΩ
Conductive Sheet or
Copper Plate
3-4
TVN_SN
CABINET DISASSEMBLY INSTRUCTIONS
[TYPE A, TYPE B]
1. Disassembly Flowchart
Removal
Step/
Loc.
No.
This flowchart indicates the disassembly steps for the
cabinet parts, and the CBA in order to gain access to
item(s) to be serviced. When reassembling, follow the
steps in reverse order. Bend, route and dress the
cables as they were.
[8] Junction
CBA
[1] Stand
Assembly
[9] IR Sensor
CBA
[2] Rear Assembly
[10] Function
CBA
[3] Inverter CBA
[12] Speaker
Holder
[13] Speaker
[4] Jack CBA
[5] Power Supply
CBA
[7] Digital Main
CBA Unit
[14] Front
Cabinet
2. Disassembly Method
Part
Fig.
No.
Note
9(S-7), *CN101,
D2
*CN301, *CN302,
D4
*CN801, *CN802
[6]
Jack Holder D2 2(S-8)
---
[7]
Digital Main D2 4(S-9), 4(S-10),
CBA Unit
D4 *CN3902, Shield Box
---
[8]
Junction
CBA
D3
*CL102A
D4
---
[9]
IR Sensor
CBA
D3
(S-11), *CL103B
D4
---
[10]
Function
CBA
D3
--------------D4
---
D3 4(S-12)
---
D3 2(S-13), 4(S-14)
---
[13] Speaker
D3 ---------------
---
[14]
Front
Cabinet
D3 ---------------
---
↓
(1)
↓
(2)
↓
(3)
↓
(5)
Speaker
Holder
---
↓
(4)
Note:
Removal
Remove/*Unhook/
Unlock/Release/
Unplug/Unclamp/
Desolder
Remove/*Unhook/
Unlock/Release/
Unplug/Unclamp/
Desolder
Power
Supply
CBA
[12]
[11] LCD Module
Assembly
Fig.
No.
[5]
LCD
[11] Module
Assembly
[6] Jack Holder
Step/
Loc.
No.
Part
(1) Order of steps in procedure. When reassembling,
follow the steps in reverse order. These numbers
are also used as the Identification (location) No. of
parts in figures.
Note
(2) Parts to be removed or installed.
[1]
Stand
Assembly
D1 3(S-1)
[2]
Rear
Assembly
D1 13(S-2), 2(S-3), 3(S-4)
---
[3]
Inverter
CBA
6(S-5), *CN1001,
D2 *CN1003, *CN1050,
D4 *CN1100, *CN1150,
*CN1200, *CN1900
---
[4]
Jack CBA
D2
2(S-6), *CL701B
D4
---
(3) Fig. No. showing procedure of part location
---
(4) Identification of parts to be removed, unhooked,
unlocked, released, unplugged, unclamped, or
desoldered.
P = Spring, L = Locking Tab, S = Screw,
H = Hex Screw, CN = Connector
* = Unhook, Unlock, Release, Unplug, or Desolder
e.g. 2(S-2) = two Screws (S-2),
2(L-2) = two Locking Tabs (L-2)
(5) Refer to the following "Reference Notes in the
Table."
4-1
PL10.3DC
(S-2)
[2] Rear Assembly
(S-3)
(S-3)
(S-2)
(S-2)
(S-2)
(S-4)
[1] Stand Assembly
(S-1)
Fig. D1
4-2
PL10.3DC
[3] Inverter CBA
(S-5)
(S-5)
[4] Jack CBA
(S-7)
(S-10)
Shield Box
[7] Digital Main
CBA Unit
(S-9)
(S-7)
(S-9)
(S-8)
(S-7)
(S-6)
[6] Jack Holder
[5] Power Supply CBA
Fig. D2
4-3
PL10.3DC
[14] Front Cabinet
[13] Speaker
[12] Speaker
(S-14)
Holder
(S-13)
(S-14)
[13] Speaker
(S-12)
[12] Speaker
Holder
(S-13)
[11] LCD Module
Assembly
[10] Function CBA
[8] Junction
CBA
(S-12)
(S-11)
[9] IR Sensor CBA
Fig. D3
4-4
PL10.3DC
TV Cable Wiring Diagram
Inverter CBA
Jack
CBA
CN1050
Power Supply CBA
CL701B
CN1100
CN201
CN1001
CN1150
CL701A
CN602
CN1900
CN302
CN301
CN101
CN1200
AC CORD
CN801
CN802
To LCD Module
Assembly
To Speaker
Digital Main
CBA Unit
Junction
CBA
CN151
CN3702
CN3701
CN3902
CN1003
CL102A
IR Sensor CBA
Function CBA
CL103B
CL103A
CL102B
To LCD Module
Assembly
Fig. D4
4-5
PL10.3DC
[TYPE C]
1. Disassembly Flowchart
Removal
Step/
Loc.
No.
This flowchart indicates the disassembly steps for the
cabinet parts, and the CBA in order to gain access to
item(s) to be serviced. When reassembling, follow the
steps in reverse order. Bend, route and dress the
cables as they were.
[1] Stand
Assembly
[8] IR Sensor
CBA
[2] Rear Assembly
[9] Function
CBA
[3] Inverter CBA
[11] Speaker
Holder
[12] Speaker
[4] Jack CBA
[5] Power Supply
CBA
Part
9(S-7), *CN101,
D2
*CN301, *CN302,
D4
*CN801, *CN802
[6]
Jack Holder D2 2(S-8)
---
[7]
Digital Main D2 4(S-9), 4(S-10),
CBA Unit
D4 *CN3902, Shield Box
---
[8]
IR Sensor
CBA
D3
(S-11), *CL103B
D4
---
[9]
Function
CBA
D3
--------------D4
---
D3 4(S-12)
---
D3 2(S-13), 4(S-14)
---
[12] Speaker
D3 ---------------
---
[13]
Front
Cabinet
D3 ---------------
---
↓
(1)
↓
(2)
↓
(3)
↓
(5)
[11]
[13] Front
Cabinet
Note
Power
Supply
CBA
[6] Jack Holder
[10] LCD Module
Assembly
Remove/*Unhook/
Unlock/Release/
Unplug/Unclamp/
Desolder
[5]
LCD
[10] Module
Assembly
[7] Digital Main
CBA Unit
Fig.
No.
Speaker
Holder
↓
(4)
---
Note:
2. Disassembly Method
(1) Order of steps in procedure. When reassembling,
follow the steps in reverse order. These numbers
are also used as the Identification (location) No. of
parts in figures.
Removal
Step/
Loc.
No.
Part
Fig.
No.
Remove/*Unhook/
Unlock/Release/
Unplug/Unclamp/
Desolder
(3) Fig. No. showing procedure of part location
[1]
Stand
Assembly
D1 3(S-1)
---
[2]
Rear
Assembly
D1 13(S-2), 2(S-3), 3(S-4)
---
[3]
Inverter
CBA
6(S-5), *CN1001,
D2 *CN1003, *CN1050,
D4 *CN1100, *CN1150,
*CN1200, *CN1900
---
Jack CBA
D2
2(S-6), *CL701B
D4
---
[4]
(2) Parts to be removed or installed.
Note
(4) Identification of parts to be removed, unhooked,
unlocked, released, unplugged, unclamped, or
desoldered.
P = Spring, L = Locking Tab, S = Screw,
H = Hex Screw, CN = Connector
* = Unhook, Unlock, Release, Unplug, or Desolder
e.g. 2(S-2) = two Screws (S-2),
2(L-2) = two Locking Tabs (L-2)
(5) Refer to the following "Reference Notes in the
Table."
4-6
PL10.3(A01FU)DC
(S-2)
[2] Rear Assembly
(S-3)
(S-3)
(S-2)
(S-2)
(S-2)
(S-4)
[1] Stand Assembly
(S-1)
Fig. D1
4-7
PL10.3(A01FU)DC
[3] Inverter CBA
(S-5)
(S-5)
[4] Jack CBA
(S-7)
(S-10)
Shield Box
[7] Digital Main
CBA Unit
(S-9)
(S-7)
(S-9)
(S-8)
(S-7)
(S-6)
[6] Jack Holder
[5] Power Supply CBA
Fig. D2
4-8
PL10.3(A01FU)DC
[13] Front Cabinet
[12] Speaker
[11] Speaker
(S-14)
Holder
(S-13)
(S-14)
[13] Speaker
(S-12)
[11] Speaker
Holder
(S-13)
[10] LCD Module
Assembly
[9] Function CBA
(S-12)
(S-11)
[8] IR Sensor CBA
Fig. D3
4-9
PL10.3(A01FU)DC
TV Cable Wiring Diagram
Inverter CBA
Jack
CBA
CN1050
Power Supply CBA
CL701B
CN1100
CN201
CN1001
CN1150
CL701A
CN602
CN1900
CN302
CN301
CN101
CN1200
AC CORD
CN1003
CN801
CN802
To LCD Module
Assembly
To Speaker
Digital Main
CBA Unit
CN3702
CN3701
CN3902
IR Sensor CBA
Function CBA
CL103B
CL103A
CL102
To LCD Module
Assembly
Fig. D4
4-10
PL10.3(A01FU)DC
ELECTRICAL ADJUSTMENT INSTRUCTIONS
How to set up the service mode:
General Note: “CBA” is abbreviation for
“Circuit Board Assembly.”
Service mode:
Note: Electrical adjustments are required after
replacing circuit components and certain
mechanical parts. It is important to perform
these adjustments only after all repairs and
replacements have been completed.
Also, do not attempt these adjustments unless
the proper equipment is available.
1. Turn the power on.
2. Press [MENU] button to display Setup menu.
3. Select “Features”.
4. Select “Current Software Info”.
5. Press [0], [6], [2], [5], [9], [6] and [Info] buttons on
the remote control unit in this order. The following
screen appears.
Test Equipment Required
1. NTSC Pattern Generator (Color Bar W/White
Window, Red Color, Dot Pattern, Gray Scale,
Monoscope, Multi-Burst)
"*" differs depending on the models.
Code : *******-***-*-*****-****
Pic code : **-*******-*****-**
2. Remote control unit
MIPS : Push 0key
3. Color Analyzer
Press "POWER" key to exit.
Tuner : ****-*****-****
Safety : safety_Non
5-1
PL10.3EA
1. Purity Check Mode
2. VCOM Adjustment
This mode cycles through full-screen displays of red,
green, blue, and white to check for non-active pixels.
Test Point
Adj. Point
1. Enter the Service mode.
Screen
2. Each time pressing [7] button on the remote
control unit, the display changes as follows.
[CHANNEL UP/DOWN ]
buttons
M. EQ.
Spec.
Color analyzer
See below
Purity Check Mode
Figure
White mode
To avoid interference from ambinent
light, this adjustment should be
performed in a dark room.
[7] button
Perpendicularity
[7] button
Black mode
L = 3 cm
Color Analyzer
[7] button
Red mode
TYPE A:
1. Operate the unit for more than 60 minutes.
2. Set the color analyzer and bring the optical
receptor to the center on the LCD-Panel surface
after zero point calibration as shown above.
Note: The optical receptor must be set
perpendicularly to the LCD Panel surface.
[7] button
Green mode
3. Enter the Service mode.
4. Press [3] button on the remote control unit.
5. Press [CHANNEL UP/DOWN] buttons on the
remote control unit so that the color analyzer value
becomes minimum.
[7] button
Blue mode
6. To cancel or to exit from the VCOM Adjustment,
press [PREV CH] button.
TYPE B, TYPE C:
1. Set the color analyzer and bring the optical
receptor to the center on the LCD-Panel surface
after zero point calibration as shown above.
Note: The optical receptor must be set
perpendicularly to the LCD Panel surface.
[7] button
White 20% mode
2. Enter the Service mode.
3. Press [2] button on the remote control unit.
4. Press [CHANNEL UP/DOWN] buttons on the
remote control unit so that the color analyzer value
becomes minimum within 2minutes from
Power-On.
Note:
When entering this mode, the default setting is White mode.
3. To cancel or to exit from the Purity Check Mode,
press [PREV CH] button.
5. To cancel or to exit from the VCOM Adjustment,
press [PREV CH] button.
5-2
PL10.3-2EA
The White Balance Adjustment should be
performed when replacing the LCD Panel
or Digital Main CBA.
Purpose: To mix red, green and blue beams correctly
for pure white.
5. [CUTOFF]
Press [1] button to select “COR” for Red Cutoff
adjustment. Press [3] button to select “COB” for
Blue Cutoff adjustment.
[DRIVE]
Press [4] button to select “DR” for Red Drive
adjustment. Press [6] button to select “DB” for Blue
Drive adjustment.
Symptom of Misadjustment: White becomes bluish
or reddish.
6. In each color mode, press [CHANNEL UP/DOWN]
buttons to adjust the values of color.
Test Point Adj. Point
7. Adjust Cutoff and Drive so that the color
temperature becomes 12000°K (x= 0.272 / y=
0.278 ±0.005).
3. White Balance Adjustment
Screen
[VOLUME
DOWN]
button
Mode
Input
[VIDEO1]
C/D
White Raster
(APL 70%)
or
(APL 40%)
M. EQ.
Spec.
Pattern Generator,
Color analyzer
x= 0.272 ± 0.005
y= 0.278 ± 0.005
8. To cancel or to exit from the White Balance
Adjustment, press [PREV CH] button.
Figure
To avoid interference from ambinent
light, this adjustment should be
performed in a dark room.
Perpendicularity
L = 3 cm
INPUT: WHITE 70%, 40% Color Analyzer
1. Operate the unit for more than 60 minutes.
2. Input the White Raster(70%=70IRE, 40%=40IRE).
INPUT SIGNAL
0IRE
0IRE
Low
Light
Hight
Light
100IRE
100IRE
40%=40IRE
70%=70IRE
3. Set the color analyzer to the CHROMA mode and
bring the optical receptor to the center on the
LCD-Panel surface after zero point calibration as
shown above.
Note: The optical receptor must be set
perpendicularly to the LCD Panel surface.
4. Enter the Service mode. Press [VOLUME DOWN]
button on the remote control unit and select “C/D”
mode.
5-3
PL10.3-2EA
HOW TO INITIALIZE THE LCD TV
The purpose of initialization is to place the set in a new out of box condition. The customer will be prompted to
select a language and program channels after the set has been initialized.
To put the program back at the factory-default, initialize the LCD TV using the following procedure.
1. Turn the power on.
2. Enter the service mode.
- To cancel the service mode, press [POWER]
button on the remote control unit.
3. Press [INFO] button on the remote control unit to
initialize the LCD television.
4. "INITIALIZED" will appear in the upper right of the
screen. "INITIALIZED" color will change to green
from red when initializing is completed.
6-1
PL10.3INT
FIRMWARE RENEWAL MODE
Equipment Required
The appearance shown in *1 is described as follows.
Appearance
a. USB storage device
b. Remote Control Unit
State
Downloading...
Downloading the firmware from
the USB storage device.
Firmware Update Procedure
Writing...
Writing the downloaded firmware
in flash memory.
Note: There are two states (the User Upgrade and
the Factory Upgrade) in firmware update.
Checking...
Checking the new firmware.
User Upgrade
Upgrade the firmware only.
The setting values are not
initialized.
Factory upgrade
Upgrade the firmware and
initialize the setting values.
5. When the firmware update is completed, the
following will appear on the screen.
Software Upgrade
The identification of User Upgrade and Factory
Upgrade are done by the filename.
1. Turn the power off and unplug the AC Cord.
The software upgrade is completed.
Remove USB storage device, turn TV off then on again.
2. Insert the USB storage device to the USB port as
shown below.
Rear Cabinet
Remove the USB storage device from the USB
port.
Turn the power off and turn the power on again.
Note:
When the Factory Upgrade is used, after
restarting TV, shift to initial screen menu in service
mode. "INITIALIZED" will appear on the upper
right of the screen. "INITIALIZED" color will
change to green from red when initializing is
completed.
USB storage
device
3. Plug the AC cord in the wall outlet and turn the
power on.
4. The update will start and the following will appear
on the screen.
"*" differs depending on the models.
Software Upgrade
Software upgrade in progress. Please wait.
Do not remove the USB storage device or
turn the TV off while upgrade is in progress.
Current Version: *******-***-*-***-****
New Version: *******-***-*-***-****
*1
Downloading...
0%
Note: If the above screen isn’t displayed, repeat from
step 1.
7-1
PL10.3FW
TROUBLESHOOTING
[ Power Supply Section ]
FLOW CHART NO.1
The power cannot be turned on.
No
Is the fuse (F601) normal?
See FLOW CHART No.2 <The fuse blows out.>
Yes
Is normal state restored when once unplugged
power cord is plugged again several seconds?
No
Yes
Is the AL+33V line voltage normal?
No
Check if there is any leak or short-circuiting on the
primary circuit component, and service it if defective.
(C605, D601, D602, D603, D604, Q601, Q602,
Q603, Q604, IC602, T601)
Yes
Check each rectifying circuit of the secondary
circuit and service it if defective.
FLOW CHART NO.2
The fuse blows out.
Check the presence that the primary component
is leaking or shorted and service it if defective.
Check the presence that the rectifying diode or circuit
is shorted in each rectifying circuit of secondary side,
and service it if defective.
After servicing, replace the fuse.
FLOW CHART NO.3
When the output voltage fluctuates.
Does the photocoupler circuit on the
secondary side operate normally?
No
Check IC601, D639, D652, D653, Q631 and their
periphery circuit, and service it if defective.
Yes
Check IC601, D615, D616, IC602 and their periphery,
circuit and service it if defective.
FLOW CHART NO.4
When buzz sound can be heard in the vicinity of power circuit.
Check if there is any short-circuit on the rectifying diode and the circuit in each rectifying circuit of the secondary side,
and service it if defective. (IC631, Q207, Q209, Q210, Q211, Q501, Q635, Q636, Q637, Q640, Q641, Q642, Q643,
D631, D632, D633, D638, D641, D642, D646, D647)
FLOW CHART NO.5
AL+33V is not output.
Is approximately +34V voltage supplied to the
cathode of D638?
No
Check C638, D638, D639 and their periphery
circuit, and service it if defective.
Yes
Check D657, R661 and their periphery circuit, and
service it if defective.
8-1
PL10.3TR
FLOW CHART NO.6
LCD+24.5V is not output.
Is approximately +30V voltage supplied to the collector
of Q210?
No
See FLOW CHART No.5<AL+33V is not output>
Yes
Check Q207, Q208, D205, P-ON-H1 line and their
periphery circuit, and service it if defective.
FLOW CHART NO.7
LCD+16V is not output.
Is approximately +17V voltage supplied to the
collector of Q209?
No
Check C631, D631, D635 and their periphery circuit,
and service it if defective.
Yes
Is approximately +16.5V voltage supplied to the
base of Q209?
No
Check Q207, Q208, D203, D204, D211, P-ON-H1 line
and their periphery circuit, and service it if defective.
Yes
Replace Q209.
FLOW CHART NO.8
INV+16V is not output.
Is approximately +17V voltage supplied to the
collector of Q501?
No
Check C631, D631, D635 and their periphery circuit,
and service it if defective.
Yes
Is approximately +16.5V voltage supplied to the
base of Q501?
No
Check Q207, Q208, D203, D204, D211, P-ON-H1 line
and their periphery circuit, and service it if defective.
Yes
Replace Q501.
FLOW CHART NO.9
P-ON+7V is not output.
Is approximately +7V voltage supplied to the
collector of D646?
No
Check C644, D646 and their periphery circuit,
and service it if defective.
Yes
Check if there is any leak or short-circuit on
the loaded circuit, and service it if defective.
8-2
PL10.3TR
FLOW CHART NO.10
P-ON+5V is not output. (LCD+16V is outputted normally.)
Is approximately +6.8V voltage supplied to the
collector of Q641?
No
See FLOW CHART No.9 <P-ON+7V is not output.>
Yes
Is approximately +6V voltage supplied to the
base of Q641?
No
Check D645 and their periphery circuit, and service
it if defective.
Yes
Replace Q641.
FLOW CHART NO.11
TUNER+5V is not output. (LCD+16V is outputted normally.)
Is approximately +6.7V voltage supplied to the
collector of Q640?
No
See FLOW CHART No.9 <P-ON+7V is not output.>
Yes
Is approximately +6V voltage supplied to the
base of Q640?
No
Check D645 and their periphery circuit, and service
it if defective.
Yes
Replace Q640.
FLOW CHART NO.12
AL+13V is not output.
Is approximately +13V voltage supplied to the
cathode of D641 and D642?
No
Check C639, D641, D642 and their periphery circuit,
and service it if defective.
Yes
Check if there is any leak or short-circuit on
the loaded circuit, and service it if defective.
FLOW CHART NO.13
P-ON+3V is not output.
Is approximately +3V voltage supplied to the
cathode of D647?
No
Check C645, D647 and their periphery circuit, and
service it if defective.
Yes
Check if there is any leak or short-circuit on
the loaded circuit, and service it if defective.
8-3
PL10.3TR
FLOW CHART NO.14
P-ON+3.3V is not output.
Is approximately +5V voltage supplied to the
cathode of D633?
No
Check C633, D633 and their periphery circuit, and
service it if defective.
Yes
Is the "H" signal (approximately +3.5V) inputted to the
base of Q637?
No
Check Q638, Q639, D666, P-ON-H2 line and their
periphery circuit, and service it if defective.
Yes
Replace Q637.
FLOW CHART NO.15
P-ON+9V is not output. (LCD+16V is outputted normally.)
Is approximately +13V voltage supplied to the
collector of Q642?
No
See FLOW CHART No.12 <AL+13V is not output.>
Yes
Is approximately +10V voltage supplied to the
base of Q642?
No
Check D670 and their periphery circuit, and service
it if defective.
Yes
Replace Q642.
FLOW CHART NO.16
AL+3.3V is not output.
Is approximately +34V voltage supplied to the
collector of Q635?
No
See FLOW CHART No.5 <AL+33V is not output.>
Yes
Is approximately +5V voltage supplied to Pin(3) of
IC631?
No
Check Q635, D659 and their periphery circuit, and
service it if defective.
Yes
Replace IC631.
FLOW CHART NO.17
LCD-6.8V is not output.
Is approximately -9V voltage supplied to the
Anode of D632?
No
Check C632, D632 and their periphery
circuit, and service it if defective.
Yes
Is approximately -8V voltage supplied to the
base of Q211?
No
Check Q207, Q208, D208, P-ON-H1 line and their
periphery circuit, and service it if defective.
Yes
Replace Q211.
8-4
PL10.3TR
[ Video Signal Section ]
FLOW CHART NO.1
The key operation is not functioning.
Are the contact point and installation state of the key
switches (SW101B, SW103B~SW107B) normal?
No
Re-install the switches (SW101B, SW103B~SW107B)
correctly or replace the poor switch.
Yes
When pressing each switches (SW101B, SW103B~
SW107B) do the voltage of Pin(29) of CN302 ?
No
Check the switches (SW101B, SW103B~SW107B)
and their periphery, and service it if defective.
Yes
Replace Digital Main CBA Unit.
FLOW CHART NO.2
No operation is possible from the remote control unit.
Operation is possible from the remote control unit.
Is 3.3V voltage supplied to Pin(2) terminal of the
remote control receiver (RS101)?
No
Check AL+3.3V line and service it if defective.
Yes
No
Is the "L" pulse sent out Pin(1) terminal of remote
control receiver (RS101) when the infrared remote
control is activated?
Replace the remote control receiver(RS101)
or the remote control unit.
Yes
Is the "L" pulse supplied to Pin(25) of CN301?
No
Yes
Replace Digital Main CBA Unit.
Check the line between Pin(1) terminal of remote
control receiver(RS101) and Pin(25) of CN301,
and service it if defective.
FLOW CHART NO.3
Picture does not appear normally.(Video input)
Are the video signal inputted to Pin(4) of CN302?
No
Yes
Check the line between Pin(4) of CN302 and
JK752, and service it if defective.
Replace Digital Main CBA Unit or LCD Module
Assembly.
8-5
PL10.3TR
FLOW CHART NO.4
Picture does not appear normally.(Tuner input)
Are the DIF signal inputted to the Pin(26,28) of CN302?
No
Yes
Check the line between Pin(26, 28) of CN302 and
Pin(12, 13) of TU301, and service it if defective.
Replace Digital Main CBA Unit or LCD Module
Assembly.
FLOW CHART NO.5
Picture does not appear normally.(S-Video input)
Are the video signal outputted to the Pin(6, 8) of
CN302?
No
Check the line between Pin(6, 8) of CN302 and
JK751, and service it if defective.
Pin(6): S-VIDEO-C
Pin(8): S-VIDEO-Y
Yes
Replace Digital Main CBA Unit or LCD Module
Assembly.
FLOW CHART NO.6
Picture does not appear normally.(Y/Pb/Pr input)
Are the video signal inputted to the Pin(15, 17, 19) of
CN302?
No
Pin(15): VIDEO-Y
Pin(17): VIDEO-Pb
Pin(19): VIDEO-Pr
Check the line between Pin(15, 17, 19) of CN302
and input terminals(JK731, JK732, JK733), and
service it if defective.
Yes
Replace Digital Main CBA Unit or LCD Module
Assembly.
8-6
PL10.3TR
[ Audio Signal Section ]
FLOW CHART NO.1
Audio is not outputted normally.(Audio input)
Are the audio(L/R) signals inputted to Pin(2, 15)
of IC771?
No
Yes
Are the audio(L/R) signals inputted to each pin of
CN301?
Pin(6) :
Pin(8) :
Pin(2) :
Pin(4) :
No
Check the line between Pin(2, 15) of IC771 and
input terminal(JK753, JK754), and service it if
defective.
Replace Digital Main CBA Unit.
AMP(L)-OUT
AMP(R)-OUT
AUDIO(L)-OUT
AUDIO(R)-OUT
Yes
Are the audio(L/R) signals inputted to the Pin(3, 40)
of IC801?
No
Check the line between Pin(6, 8) of CN301 and
Pin(3, 40) of IC801, and service it if defective.
Are the audio(L/R) signals inputted to the Pin(3, 5)
of IC871?
No
Check the line between Pin(2, 4) of CN301 and
Pin(3, 5) of IC871, and service it if defective.
Yes
Are the audio(L/R) signals outputted to the Pin(1, 2)
of CN801 and CN802?
CN801: SP(L)
CN802: SP(R)
No
Yes
Are the audio(L/R) signals outputted to the audio
output terminal?
JK871: AUDIO(L)-OUT
JK872: AUDIO(R)-OUT
No
8-7
Check IC801 and their periphery circuit, and
service it if defective.
Check SP801,SP802 and their periphery circuit,
and service it if defective.
Check the line between Pin(1, 7) of IC871 and audio
output terminal(JK871, JK872), and service it if
defective.
PL10.3TR
FLOW CHART NO.2
Audio is not outputted normally.(Component Audio input)
Are the audio(L/R) signals inputted to the Pin(4, 11)
of IC771?
No
Yes
Are the audio(L/R) signals inputted to each pin of
CN301?
Pin(6) :
Pin(8) :
Pin(2) :
Pin(4) :
No
Check the line between Pin(4, 11) of IC771 and
input terminal(JK741, JK742), and service it if
defective.
Replace Digital Main CBA Unit.
AMP(L)-OUT
AMP(R)-OUT
AUDIO(L)-OUT
AUDIO(R)-OUT
Yes
Are the audio(L/R) signals inputted to the Pin(3, 40)
of IC801?
No
Check the line between Pin(6, 8) of CN301 and
Pin(3, 40) of IC801, and service it if defective.
Are the audio(L/R) signals inputted to the Pin(3, 5)
of IC871?
No
Check the line between Pin(2, 4) of CN301 and
Pin(3, 5) of IC871, and service it if defective.
Yes
Are the audio(L/R) signals outputted to the Pin(1, 2)
of CN801 and CN802?
CN801: SP(L)
CN802: SP(R)
No
Yes
Are the audio(L/R) signals outputted to the audio
output terminal?
JK871: AUDIO(L)-OUT
JK872: AUDIO(R)-OUT
No
8-8
Check IC801 and their periphery circuit, and
service it if defective.
Check SP801,SP802 and their periphery circuit,
and service it if defective.
Check the line between Pin(1, 7) of IC871 and audio
output terminal(JK871, JK872), and service it if
defective.
PL10.3TR
FLOW CHART NO.3
Audio is not outputted normally.(Tuner input)
Are the DIF signals outputted to the Pin(26, 28)
of CN302?
No
Check TU301 and their periphery circuit, and
service it if defective.
Yes
Are the audio(L/R) signals inputted to each pin of
CN301?
Pin(6) :
Pin(8) :
Pin(2) :
Pin(4) :
No
Replace Digital Main CBA Unit.
AMP(L)-OUT
AMP(R)-OUT
AUDIO(L)-OUT
AUDIO(R)-OUT
Yes
Are the audio(L/R) signals inputted to the Pin(3, 40)
of IC801?
No
Check the line between Pin(6, 8) of CN301 and
Pin(3, 40) of IC801, and service it if defective.
Are the audio(L/R) signals inputted to the Pin(3, 5)
of IC871?
No
Check the line between Pin(2, 4) of CN301 and
Pin(3, 5) of IC871, and service it if defective.
Yes
Are the audio(L/R) signals outputted to the Pin(1, 2)
of CN801 and CN802?
CN801: SP(L)
CN802: SP(R)
No
Yes
Are the audio(L/R) signals outputted to the audio
output terminal?
JK871: AUDIO(L)-OUT
JK872: AUDIO(R)-OUT
No
8-9
Check IC801 and their periphery circuit, and
service it if defective.
Check SP801,SP802 and their periphery circuit,
and service it if defective.
Check the line between Pin(1, 7) of IC871 and audio
output terminal(JK871, JK872), and service it if
defective.
PL10.3TR
9-1
N1 CLKIN
N2 CLKOUT
X3101
25MHz
OSC
SCK
SIN
SOUT
CS
WP
AB25
AB24
AC25
AC24
E11
DIGITAL MAIN CBA UNIT
SCK
SI
SO
CS
WP
AD5
AD4
AE5
AB18
AB16
AB23
SCL AC18
SDA AC19
PROTECT1
PROTECT2
PROTECT3
VCOM-PWM
BACKLIGHT-SW
BACKLIGHT-ADJ
E1 INPUT0
E2 INPUT1
AB9 AUDIO-MUTE
6
5
2
1
3
INPUT0
INPUT1
AUDIO-MUTE
IC3101 (MEMORY)
TO AUDIO
BLOCK
DIAGRAM
REMOTE R22
P-ON-H2 AB13
P-ON-H1 R23
REMOTE E3
KEY-IN1 AC5
IC3301
(MAIN MICRO CONTROLLER)
CN301
25
1
9
CN302
29
22 SCL
21 SDA
CN3702
CN302
22
21
CN301
11
11 PROTECT1
15
15 PROTECT2
5
5 PROTECT3
29
29 VCOM-PWM
26
BACKLIGHT-SW
26
28 BACKLIGHT-ADJ 28
CN3701
CN3701
25 REMOTE
1 P-ON-H2
9 P-ON-H1
CN3702
29 KEY-IN1
* TU301
(TUNER UNIT)
POWER SUPPLY CBA
4 SCL
5 SDA
* TU301
(TUNER UNIT)
CL103B
3 KEY-IN1
6
5
4
14
CN201
TO
POWER SUPPLY
BLOCK DIAGRAM
PROTECT3
BACKLIGHT-SW
BACKLIGHT-ADJ
VCOM
D101
POWER
IR SENSOR CBA
CL103A
3
CL102B
2
5
4
REMOTE
SENSOR
RS101
TO
INVERTER
BLOCK
DIAGRAM
(CN1001)
CL102A
2 REMOTE
5 P-ON+9V
4 KEY-IN1
FUNCTION CBA
DRIVE
IC201,Q203,
Q204,Q205
Either TU301 is used for Power Supply CBA.
9 SCL
8 SDA
CN151
2
5
4
JUNCTION
CBA
KEY SWITCH
CN101
2 REMOTE
5 P-ON+9V
4 KEY-IN1
P-ON-H2
P-ON-H1
PROTECT1
PROTECT2
P-ON+9V
[TYPE A]
1. System Control Block Diagram
BLOCK DIAGRAMS
PL10.3ABLS
JK751
S-VIDEO
-IN
C
Y
9-2
CL701B
5
3
1
2
VIDEO-IN
S-VIDEO-C-IN
S-VIDEO-Y-IN
S-VIDEO-SW-IN
CL701A
5
3
1
2
DIF-OUT1 11
DIF-OUT2 10
IF-AGC 9
(TUNER UNIT)
* TU301
DIF-OUT1 13
DIF-OUT2 12
IF-AGC 14
(TUNER UNIT)
* TU301
Either TU301 is used for Power Supply CBA.
JK731
COMPONENT
-Y-IN
JK732
COMPONENT
-Pb-IN
JK733
COMPONENT
-Pr-IN
JACK CBA
JK752
VIDEO-IN
POWER SUPPLY CBA
WF4
WF2
WF5
WF3
WF6
WF1
VIDEO-IN
S-VIDEO-C-IN
S-VIDEO-Y-IN
S-VIDEO-SW
COM-VIDEO-Y-IN
COM-VIDEO-Pb-IN
COM-VIDEO-Pr-IN
CN302
26 DIF-OUT1
28 DIF-OUT2
24 IF-AGC
CN302
4
6
8
5
15
17
19
CN3702
26
28
24
CN3702
4
6
8
5
15
17
19
DIGITAL MAIN CBA UNIT
DIF-OUT1
DIF-OUT2
IF-AGC
VIDEO-IN
S-VIDEO-C-IN
S-VIDEO-Y-IN
S-VIDEO-SW
COM-VIDEO-Y-IN
COM-VIDEO-Pb-IN
COM-VIDEO-Pr-IN
AUDIO SIGNAL
TO DIGITAL
SIGNAL PROCESS
BLOCK DIAGRAM
VIDEO SIGNAL
2. Video Block Diagram
PL10.3BLV
JACK CBA
9-3
Q873,Q874
DRIVE
SP802
SPEAKER
R-CH
SP801
SPEAKER
L-CH
JK841
DIGITAL
AUDIO-OUT
(COAXIAL)
CN801
SP(L)+ 2
SP(L)- 1
CN802
SP(R)+ 2
SP(R)- 1
CL801
CL802
BUFFER
Q841
PWM
GENERATOR
36
GAIN
CONTROL
GAIN
CONTROL
40
3
Q771
13
3
Q772
Q801
POWER SUPPLY CBA
4
CONTROL LOGIC
PWM
GENERATOR
PWM
GENERATOR
15
28
PWM
GENERATOR
8
5
3
9 10
CONTROL
LOGIC
IC871
(OP AMP)
IC801 (AUDIO AMP)
7
MUTE
2
4
1
5
IC771
(AUDIO SELECTOR)
15
11
12
14
JK872
AUDIO(R)-OUT
Q872
MUTE
CL701A
7
9
1
Q871
CL701B
7 AUDIO(L)-IN
9 AUDIO(R)-IN
JK871
AUDIO(L)-OUT
JK721
HDMIAUDIO(L)-IN
JK722
HDMIAUDIO(R)-IN
JK741
COMPONENTAUDIO(L)-IN
JK742
COMPONENTAUDIO(R)-IN
JK753
AUDIO(L)
-IN
JK754
AUDIO(R)
-IN
WF7
AUDIO(L)-OUT
AUDIO(R)-OUT
AMP(L)-OUT
AMP(R)-OUT
CN302
2 SPDIF
20 AUDIO-MUTE
CN301
2
4
6
8
CN302
10 INPUT1
12 INPUT0
CN302
13 AUDIO(L)
11 AUDIO(R)
CN3702
2
20
CN3701
2
4
6
8
CN3702
10
12
CN3702
13
11
8
7
6
5
8
7
6
5
DIGITAL MAIN CBA UNIT
(L-CH)
15
D/A
(R-CH) CONVERTER
14
IC3801
(D/A CONVERTER)
(L-CH)
D/A
15
(R-CH) CONVERTER
14
IC3802
(D/A CONVERTER)
35
36
33
37
34
DSP
2
40
4
39
3
IC3803
(AUDIO DSP)
SPDIF
LRCLK
BCLK
ADATA2
ACLK
ADATA1
INPUT1
INPUT0
AUDIO-MUTE
AUDIO(L)
AUDIO(R)
TO
DIGITAL
SIGNAL
PROCESS
BLOCK
DIAGRAM
TO
SYSTEM
CONTROL
BLOCK
DIAGRAM
TO
DIGITAL
SIGNAL
PROCESS
BLOCK
DIAGRAM
AUDIO SIGNAL
3. Audio Block Diagram
PL10.3BLA
9-4
TMDS-D0(+)
TMDS-D0(-)
TMDS-D1(+)
TMDS-D1(-)
TMDS-D2(+)
TMDS-D2(-)
TMDS-CLOCK(+)
TMDS-CLOCK(-)
SDA
SCL
TMDS-D0(+)
TMDS-D0(-)
TMDS-D1(+)
TMDS-D1(-)
TMDS-D2(+)
TMDS-D2(-)
TMDS-CLOCK(+)
TMDS-CLOCK(-)
SDA
SCL
7
9
4
6
HDMI-IN3 1
3
10
12
16
15
TMDS-D0(+)
TMDS-D0(-)
TMDS-D1(+)
TMDS-D1(-)
TMDS-D2(+)
TMDS-D2(-)
TMDS-CLOCK(+)
TMDS-CLOCK(-)
SDA
SCL
JK3704
7
9
4
6
HDMI-IN2 1
3
10
12
16
15
JK3702
7
9
4
6
1
HDMI-IN1
3
10
12
16
15
JK3701
TO AUDIO
BLOCK DIAGRAM
TO VIDEO
BLOCK DIAGRAM
TO VIDEO
BLOCK DIAGRAM
AUDIO(L)
AUDIO(R)
BCLK
LRCLK
ACLK
SPDIF
ADATA0
ADATA1
IF-AGC
S-VIDEO-SW
DIF-OUT1
DIF-OUT2
VIDEO-IN
S-VIDEO-C-IN
S-VIDEO-Y-IN
COM-VIDEO-Y-IN
COM-VIDEO-Pb-IN
COM-VIDEO-Pr-IN
DIGITAL MAIN CBA UNIT
B1
B2
C1
C2
D1
D2
A1
A2
A3
B3
A5
B5
C4
C5
B4
A4
B6
A6
A7
B7
A9
B9
C8
C9
B8
A8
B10
A10
A11
B11
M1
M2
AD9
AD12
AD10
AD11
AC10
AD14
A/D
CONVERTER
HDMI
I/F
VIDEO
DECODER
AUDIO
DECODER
AUDIO I/F
DEMODULATOR
/MPEG DECODER
SW
AF7 IF-AGC
C6 S-VIDEO-SW
AE2
AF2
AA3
V3
U3
U1
V1
U2
V2
IC3301 (DIGITAL SIGNAL PROCESS)
DIGITAL
SIGNAL
PROCESS
TP
POL
CPV
OE
STV
C15,C17-19,
C23,C24,D14,
D15,D17-19,
D22,D23
A13-15,A18,
A21-23,B13-15,
B17,B19-23
LVDS TX
AD23
AD24
AE23
AF23
AF22
AE22
AD21
AD22
AE21
AF21
AF20
AE20
AF24
AE24
W25
W23
Y24
Y23
Y22
B1,B9,C2,C8,
D1,D3,D7,D9,
F1,F9,G2,G8, DATA(0-15)
H1,H3,H7,H9
M2,M3,M7,M8,
N2,N3,N7,N8, ADDESS(0-12)
P2,P3,P7,P8,R2
IC3201
(DDR2 SDRAM)
VIDEO SIGNAL
CN3902
23
22
21
20
19
18
13
12
11
10
9
8
16
15
6
5
4
3
1
AUDIO SIGNAL
LLV0(+)
LLV0(-)
LLV1(+)
LLV1(-)
LLV2(+)
LLV2(-)
LLV3(+)
LLV3(-)
LLV4(+)
LLV4(-)
LLV5(+)
LLV5(-)
LLVCLK(+)
LLVCLK(-)
TP
POL
CPV
OE1
STV
LCD MODULE
ASSEMBLY
4. Digital Signal Process Block Diagram
PL10.3ABLD
TO SYSTEM
CONTROL
BLOCK
DIAGRAM
(CN201)
TO POWER
SUPPLY
BLOCK
DIAGRAM
(CN602)
10
11
12
2
Q1931
9-5
CN1001
PROTECT3
BACKLIGHT-SW
BACKLIGHT-ADJ
VCOM
COLD
HOT
Q1932
Q1930
SWITCHING
CN1900
1 +B
3 HOT-GND
4 HOT+15V
HOT CIRCUIT. BE CAREFUL.
11
3
15
8
Q1971
3
4
IC1931
2
3
2
1
Q1970
1
4
IC1930
14
7
5
4
10
2
T1950
Q1621
Q1004,
Q1005
SW
Q1800,Q1815
SW+16V
INV+16V
Q1972
NOTE:
The voltage for parts in hot circuit is measured using
hot GND as a common terminal.
Q1600
2
1
15
16
3
4 DCT
12 VCC
6
5
1
3
OVER VOLTAGE
PROTECTOR
Q1060
6
5
2
3
7
1
OVER VOLTAGE
PROTECTOR
Q1061
Q1111
OVER VOLTAGE
PROTECTOR
OVER VOLTAGE
PROTECTOR
OVER VOLTAGE
PROTECTOR
Q1110
9
10
8
Q1161
OVER VOLTAGE
PROTECTOR
Q1211
14
Q1160
OVER VOLTAGE
PROTECTOR
Q1210
8
7
6
5
8
7
6
5
8
7
6
5
2
4
T1200
1
3
2
4
T1150
1
3
2
4
T1100
1
3
8
7
OVER VOLTAGE
PROTECTOR
CURRENT
CONTROL
SWITCH
Q1550
CURRENT
CONTROL
SWITCH
Q1500
T1050
2
4
13
12
Q1003
DRIVE
Q1551,
Q1552,
Q1553
DRIVE
Q1501,
Q1502,
Q1503
Q1801,Q1802,
Q1803,Q1804
SW+16V
Q1001
8
11
IC1700
(COMPARATOR)
5 6
OSC
PWM
CONTROL
LOGIC
IC1000
(PWM CONTROL)
INVERTER CBA
CN1003
10
CN1200
1
2
CN1150
1
2
CN1100
1
2
CN1050
1
2
LCD MODULE
ASSEMBLY
VCOM
BACK
LIGHT
BACK
LIGHT
BACK
LIGHT
BACK
LIGHT
5. Inverter Block Diagram
PL10.3BLINV
TO
INVERTER
BLOCK
DIAGRAM
(CN1900)
AC601
AC CORD
LINE
FILTER
LINE
FILTER
9-6
3
4
2
1
FEED
BACK
Q631,
D653
19
18
17
16
15
14
13
12
11
COLD
IC601
ERROR
VOLTAGE DET
9
8
7
5
4
3
T601
HOT
Q602
SWITCHING
Q603,
Q604
SW
HOT+15V
BRIDGE
RECTIFIER
D601- D604
POWER SUPPLY CBA
VH
ZCD
OUT
FB
IS
VCC
IC602
SWITCHING
CONTROL
Q601
SWITCHING
CN602
1 ACL
2 HOT-GND
3 HOT-15V
8
1
5
4
3
6
L602
L601
4A/125V
F601
4A/125V
HOT CIRCUIT. BE CAREFUL.
CAUTION !
Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit.
If Main Fuse (F601) is blown , check to see that all components in the power supply
circuit are not defective before you connect the AC plug to the AC power supply.
Otherwise it may cause some components in the power supply circuit to fail.
4A/125V
Q635
+5V REG.
Q634
Q501
SW+16V
3
IC631
+3.3V
REG.
Q636
Q201, Q202,
Q212
SW
2
Q640
SW+5V
Q638,Q639
SWITCHING
Q209, Q213,
D204
SW+16V
Q207,Q208
SWITCHING
Q210
SW+24.5V
Q641,643
SW+5V
Q637,D666
SW+3.3V
Q642
SW+9V
Q401
Q211,D210
SW-6.8V
CN301
10
16
21,22
19,20
13,14
CN201
13
8,9
2
10
12
CAUTION ! : For continued protection against risk of fire,
replace only with same type 4 A, 125V fuse.
ATTENTION : Utiliser un fusible de rechange de même type de 4A, 125V.
P-ON+3V
P-ON+7V
AL+3.3V
P-ON+3.3V
P-ON+5V
LCD-6.8V
LCD+16V
INV+16V
VGH
P-ON+3.3V
CN3701
10
16
21,22
19,20
13,14
CN1001
3
7,8
14
6
4
P-ON-H1
P-ON-H2
PROTECT1
PROTECT2
DIGITAL MAIN CBA UNIT
INVERTER CBA
TO SYSTEM
CONTROL
BLOCK
DIAGRAM
P-ON+9V
AL+33V
P-ON+5V
AL+13V
TUNER+5V
AL+3.3V
P-ON+3V
P-ON+7V
AL+3.3V
P-ON+3.3V
P-ON+5V
LCD+6.8V
LCD+16V
INV+16V
VGH
P-ON+3.3V
NOTE:
The voltage for parts in hot circuit is measured using
hot GND as a common terminal.
6. Power Supply Block Diagram
PL10.3BLP
9-7
N1 CLKIN
N2 CLKOUT
X3101
25MHz
OSC
SCK
SIN
SOUT
CS
WP
AB25
AB24
AC25
AC24
E11
DIGITAL MAIN CBA UNIT
SCK
SI
SO
CS
WP
AD5
AD4
AE5
AB18
AB16
AB23
SCL AC18
SDA AC19
PROTECT1
PROTECT2
PROTECT3
VCOM-PWM
BACKLIGHT-SW
BACKLIGHT-ADJ
E1 INPUT0
E2 INPUT1
AB9 AUDIO-MUTE
6
5
2
1
3
INPUT0
INPUT1
AUDIO-MUTE
IC3101 (MEMORY)
TO AUDIO
BLOCK
DIAGRAM
REMOTE R22
P-ON-H2 AB13
P-ON-H1 R23
REMOTE E3
KEY-IN1 AC5
IC3301
(MAIN MICRO CONTROLLER)
CN301
25
1
9
CN302
29
22 SCL
21 SDA
CN3702
CN302
22
21
CN301
11
11 PROTECT1
15
15 PROTECT2
5
5 PROTECT3
29
29 VCOM-PWM
26 BACKLIGHT-SW 26
28 BACKLIGHT-ADJ 28
CN3701
CN3701
25 REMOTE
1 P-ON-H2
9 P-ON-H1
CN3702
29 KEY-IN1
* TU301
(TUNER UNIT)
POWER SUPPLY CBA
4 SCL
5 SDA
* TU301
(TUNER UNIT)
CL103B
3 KEY-IN1
6
5
4
14
CN201
TO
POWER SUPPLY
BLOCK DIAGRAM
PROTECT3
BACKLIGHT-SW
BACKLIGHT-ADJ
VCOM
D101
POWER
IR SENSOR CBA
CL103A
3
CL102B
2
5
4
REMOTE
SENSOR
RS101
TO
INVERTER
BLOCK
DIAGRAM
(CN1001)
CL102A
2 REMOTE
5 P-ON+9V
4 KEY-IN1
FUNCTION CBA
DRIVE
IC201,Q203,
Q204,Q205
Either TU301 is used for Power Supply CBA.
9 SCL
8 SDA
CN151
2
5
4
JUNCTION
CBA
KEY SWITCH
CN101
2 REMOTE
5 P-ON+9V
4 KEY-IN1
P-ON-H2
P-ON-H1
PROTECT1
PROTECT2
P-ON+9V
[TYPE B]
1. System Control Block Diagram
PL10.3BBLS
JK751
S-VIDEO
-IN
C
Y
9-8
CL701B
5
3
1
2
VIDEO-IN
S-VIDEO-C-IN
S-VIDEO-Y-IN
S-VIDEO-SW-IN
CL701A
5
3
1
2
DIF-OUT1 11
DIF-OUT2 10
IF-AGC 9
(TUNER UNIT)
* TU301
DIF-OUT1 13
DIF-OUT2 12
IF-AGC 14
(TUNER UNIT)
* TU301
Either TU301 is used for Power Supply CBA.
JK731
COMPONENT
-Y-IN
JK732
COMPONENT
-Pb-IN
JK733
COMPONENT
-Pr-IN
JACK CBA
JK752
VIDEO-IN
POWER SUPPLY CBA
WF4
WF2
WF5
WF3
WF6
WF1
VIDEO-IN
S-VIDEO-C-IN
S-VIDEO-Y-IN
S-VIDEO-SW
COM-VIDEO-Y-IN
COM-VIDEO-Pb-IN
COM-VIDEO-Pr-IN
CN302
26 DIF-OUT1
28 DIF-OUT2
24 IF-AGC
CN302
4
6
8
5
15
17
19
CN3702
26
28
24
CN3702
4
6
8
5
15
17
19
DIGITAL MAIN CBA UNIT
DIF-OUT1
DIF-OUT2
IF-AGC
VIDEO-IN
S-VIDEO-C-IN
S-VIDEO-Y-IN
S-VIDEO-SW
COM-VIDEO-Y-IN
COM-VIDEO-Pb-IN
COM-VIDEO-Pr-IN
AUDIO SIGNAL
TO DIGITAL
SIGNAL PROCESS
BLOCK DIAGRAM
VIDEO SIGNAL
2. Video Block Diagram
PL10.3BLV
JACK CBA
9-9
Q873,Q874
DRIVE
SP802
SPEAKER
R-CH
SP801
SPEAKER
L-CH
JK841
DIGITAL
AUDIO-OUT
(COAXIAL)
CN801
SP(L)+ 2
SP(L)- 1
CN802
SP(R)+ 2
SP(R)- 1
CL801
CL802
BUFFER
Q841
PWM
GENERATOR
36
GAIN
CONTROL
GAIN
CONTROL
40
3
Q771
13
3
Q772
Q801
POWER SUPPLY CBA
4
CONTROL LOGIC
PWM
GENERATOR
PWM
GENERATOR
15
28
PWM
GENERATOR
8
5
3
9 10
CONTROL
LOGIC
IC871
(OP AMP)
IC801 (AUDIO AMP)
7
MUTE
2
4
1
5
IC771
(AUDIO SELECTOR)
15
11
12
14
JK872
AUDIO(R)-OUT
Q872
MUTE
CL701A
7
9
1
Q871
CL701B
7 AUDIO(L)-IN
9 AUDIO(R)-IN
JK871
AUDIO(L)-OUT
JK721
HDMIAUDIO(L)-IN
JK722
HDMIAUDIO(R)-IN
JK741
COMPONENTAUDIO(L)-IN
JK742
COMPONENTAUDIO(R)-IN
JK753
AUDIO(L)
-IN
JK754
AUDIO(R)
-IN
WF7
AUDIO(L)-OUT
AUDIO(R)-OUT
AMP(L)-OUT
AMP(R)-OUT
CN302
2 SPDIF
20 AUDIO-MUTE
CN301
2
4
6
8
CN302
10 INPUT1
12 INPUT0
CN302
13 AUDIO(L)
11 AUDIO(R)
CN3702
2
20
CN3701
2
4
6
8
CN3702
10
12
CN3702
13
11
8
7
6
5
8
7
6
5
DIGITAL MAIN CBA UNIT
(L-CH)
15
D/A
(R-CH) CONVERTER
14
IC3801
(D/A CONVERTER)
(L-CH)
D/A
15
(R-CH) CONVERTER
14
IC3802
(D/A CONVERTER)
35
36
33
37
34
DSP
2
40
4
39
3
IC3803
(AUDIO DSP)
SPDIF
LRCLK
BCLK
ADATA2
ACLK
ADATA1
INPUT1
INPUT0
AUDIO-MUTE
AUDIO(L)
AUDIO(R)
TO
DIGITAL
SIGNAL
PROCESS
BLOCK
DIAGRAM
TO
SYSTEM
CONTROL
BLOCK
DIAGRAM
TO
DIGITAL
SIGNAL
PROCESS
BLOCK
DIAGRAM
AUDIO SIGNAL
3. Audio Block Diagram
PL10.3BLA
9-10
7
9
4
6
HDMI-IN3 1
3
10
12
16
15
TMDS-D0(+)
TMDS-D0(-)
TMDS-D1(+)
TMDS-D1(-)
TMDS-D2(+)
TMDS-D2(-)
TMDS-CLOCK(+)
TMDS-CLOCK(-)
SDA
SCL
JK3704
TMDS-D0(+)
7
TMDS-D0(-)
9
TMDS-D1(+)
4
TMDS-D1(-)
6
TMDS-D2(+)
HDMI-IN2 1 TMDS-D2(-)
3
TMDS-CLOCK(+)
10
TMDS-CLOCK(-)
12
SDA
16
SCL
15
JK3702
TMDS-D0(+)
7
TMDS-D0(-)
9
TMDS-D1(+)
4
TMDS-D1(-)
6
TMDS-D2(+)
1
TMDS-D2(-)
HDMI-IN1
3
TMDS-CLOCK(+)
10
TMDS-CLOCK(-)
12
SDA
16
SCL
15
JK3701
TO AUDIO
BLOCK DIAGRAM
TO VIDEO
BLOCK DIAGRAM
TO VIDEO
BLOCK DIAGRAM
AUDIO(L)
AUDIO(R)
BCLK
LRCLK
ACLK
SPDIF
ADATA0
ADATA1
IF-AGC
S-VIDEO-SW
DIF-OUT1
DIF-OUT2
VIDEO-IN
S-VIDEO-C-IN
S-VIDEO-Y-IN
COM-VIDEO-Y-IN
COM-VIDEO-Pb-IN
COM-VIDEO-Pr-IN
DIGITAL MAIN CBA UNIT
B1
B2
C1
C2
D1
D2
A1
A2
A3
B3
A5
B5
C4
C5
B4
A4
B6
A6
A7
B7
A9
B9
C8
C9
B8
A8
B10
A10
A11
B11
M1
M2
AD9
AD12
AD10
AD11
AC10
AD14
A/D
CONVERTER
HDMI
I/F
VIDEO
DECODER
AUDIO
DECODER
AUDIO I/F
DEMODULATOR
/MPEG DECODER
SW
AF7 IF-AGC
C6 S-VIDEO-SW
AE2
AF2
AA3
V3
U3
U1
V1
U2
V2
IC3301 (DIGITAL SIGNAL PROCESS)
DIGITAL
SIGNAL
PROCESS
TP
POL
CPV
OE
STV
C15,C17-19,
C23,C24,D14,
D15,D17-19,
D22,D23
A13-15,A18,
A21-23,B13-15,
B17,B19-23
LVDS TX
W25
W23
Y24
Y23
Y22
AD23
AD24
AE23
AF23
AF22
AE22
AD21
AD22
AF24
AE24
IC3201
(DDR2 SDRAM)
LVDS
RX
B1,B9,C2,C8,
D1,D3,D7,D9,
F1,F9,G2,G8, DATA(0-15)
H1,H3,H7,H9
M2,M3,M7,M8,
N2,N3,N7,N8, ADDESS(0-12)
P2,P3,P7,P8,R2
8
7
10
9
12
11
16
15
14
13
DATA
INPUT
LATCH
LINE BUFFER
FRC
GAMMA
CORRECTOR
DATA
PROCESSING
IC3901 (TINING CONTROLLER)
LVDS
OUTPUT
VIDEO SIGNAL
48
47
46
45
44
43
38
37
36
35
34
33
42
41
63
64
30
31
32
CN3902
23
22
21
20
19
18
13
12
11
10
9
8
16
15
6
5
4
3
1
AUDIO SIGNAL
LLV0(+)
LLV0(-)
LLV1(+)
LLV1(-)
LLV2(+)
LLV2(-)
LLV3(+)
LLV3(-)
LLV4(+)
LLV4(-)
LLV5(+)
LLV5(-)
LLVCLK(+)
LLVCLK(-)
TP
POL
CPV
OE1
STV
LCD MODULE
ASSEMBLY
4. Digital Signal Process Block Diagram
PL10.3BBLD
TO SYSTEM
CONTROL
BLOCK
DIAGRAM
(CN201)
TO POWER
SUPPLY
BLOCK
DIAGRAM
(CN602)
10
11
12
2
Q1931
9-11
CN1001
PROTECT3
BACKLIGHT-SW
BACKLIGHT-ADJ
VCOM
COLD
HOT
Q1932
Q1930
SWITCHING
CN1900
1 +B
3 HOT-GND
4 HOT+15V
HOT CIRCUIT. BE CAREFUL.
11
3
15
8
Q1971
3
4
IC1931
2
3
2
1
Q1970
1
4
IC1930
14
7
5
4
10
2
T1950
Q1621
Q1004,
Q1005
SW
Q1800,Q1815
SW+16V
INV+16V
Q1972
NOTE:
The voltage for parts in hot circuit is measured using
hot GND as a common terminal.
Q1600
2
1
15
16
3
4 DCT
12 VCC
6
5
1
3
OVER VOLTAGE
PROTECTOR
Q1060
6
5
2
3
7
1
OVER VOLTAGE
PROTECTOR
Q1061
Q1111
OVER VOLTAGE
PROTECTOR
OVER VOLTAGE
PROTECTOR
OVER VOLTAGE
PROTECTOR
Q1110
9
10
8
Q1161
OVER VOLTAGE
PROTECTOR
Q1211
14
Q1160
OVER VOLTAGE
PROTECTOR
Q1210
8
7
6
5
8
7
6
5
8
7
6
5
2
4
T1200
1
3
2
4
T1150
1
3
2
4
T1100
1
3
8
7
OVER VOLTAGE
PROTECTOR
CURRENT
CONTROL
SWITCH
Q1550
CURRENT
CONTROL
SWITCH
Q1500
T1050
2
4
13
12
Q1003
DRIVE
Q1551,
Q1552,
Q1553
DRIVE
Q1501,
Q1502,
Q1503
Q1801,Q1802,
Q1803,Q1804
SW+16V
Q1001
8
11
IC1700
(COMPARATOR)
5 6
OSC
PWM
CONTROL
LOGIC
IC1000
(PWM CONTROL)
INVERTER CBA
CN1003
10
CN1200
1
2
CN1150
1
2
CN1100
1
2
CN1050
1
2
LCD MODULE
ASSEMBLY
VCOM
BACK
LIGHT
BACK
LIGHT
BACK
LIGHT
BACK
LIGHT
5. Inverter Block Diagram
PL10.3BLINV
TO
INVERTER
BLOCK
DIAGRAM
(CN1900)
AC601
AC CORD
LINE
FILTER
LINE
FILTER
9-12
3
4
2
1
FEED
BACK
Q631,
D653
19
18
17
16
15
14
13
12
11
COLD
IC601
ERROR
VOLTAGE DET
9
8
7
5
4
3
T601
HOT
Q602
SWITCHING
Q603,
Q604
SW
HOT+15V
BRIDGE
RECTIFIER
D601- D604
POWER SUPPLY CBA
VH
ZCD
OUT
FB
IS
VCC
IC602
SWITCHING
CONTROL
Q601
SWITCHING
CN602
1 ACL
2 HOT-GND
3 HOT-15V
8
1
5
4
3
6
L602
L601
4A/125V
F601
4A/125V
HOT CIRCUIT. BE CAREFUL.
CAUTION !
Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit.
If Main Fuse (F601) is blown , check to see that all components in the power supply
circuit are not defective before you connect the AC plug to the AC power supply.
Otherwise it may cause some components in the power supply circuit to fail.
4A/125V
Q635
+5V REG.
Q634
Q501
SW+16V
3
IC631
+3.3V
REG.
Q636
Q201, Q202,
Q212
SW
2
Q640
SW+5V
Q638,Q639
SWITCHING
Q209, Q213,
D204
SW+16V
Q207,Q208
SWITCHING
Q210
SW+24.5V
Q641,643
SW+5V
Q637,D666
SW+3.3V
Q642
SW+9V
Q401
Q211,D210
SW-6.8V
CN301
10
16
21,22
19,20
13,14
CN201
13
8,9
2
10
12
CAUTION ! : For continued protection against risk of fire,
replace only with same type 4 A, 125V fuse.
ATTENTION : Utiliser un fusible de rechange de même type de 4A, 125V.
P-ON+3V
P-ON+7V
AL+3.3V
P-ON+3.3V
P-ON+5V
LCD-6.8V
LCD+16V
INV+16V
VGH
P-ON+3.3V
CN3701
10
16
21,22
19,20
13,14
CN1001
3
7,8
14
6
4
P-ON-H1
P-ON-H2
PROTECT1
PROTECT2
DIGITAL MAIN CBA UNIT
INVERTER CBA
TO SYSTEM
CONTROL
BLOCK
DIAGRAM
P-ON+9V
AL+33V
P-ON+5V
AL+13V
TUNER+5V
AL+3.3V
P-ON+3V
P-ON+7V
AL+3.3V
P-ON+3.3V
P-ON+5V
LCD+6.8V
LCD+16V
INV+16V
VGH
P-ON+3.3V
NOTE:
The voltage for parts in hot circuit is measured using
hot GND as a common terminal.
6. Power Supply Block Diagram
PL10.3BLP
9-13
N1 CLKIN
N2 CLKOUT
X3101
25MHz
OSC
SCK
SIN
SOUT
CS
WP
AB25
AB24
AC25
AC24
E11
DIGITAL MAIN CBA UNIT
SCK
SI
SO
CS
WP
AD5
AD4
AE5
AB18
AB16
AB23
SCL AC18
SDA AC19
PROTECT1
PROTECT2
PROTECT3
VCOM-PWM
BACKLIGHT-SW
BACKLIGHT-ADJ
E1 INPUT0
E2 INPUT1
AB9 AUDIO-MUTE
6
5
2
1
3
INPUT0
INPUT1
AUDIO-MUTE
IC3101 (MEMORY)
TO AUDIO
BLOCK
DIAGRAM
REMOTE R22
P-ON-H2 AB13
P-ON-H1 R23
REMOTE E3
KEY-IN1 AC5
IC3301
(MAIN MICRO CONTROLLER)
CN301
25
1
9
CN302
29
22 SCL
21 SDA
CN3702
CN302
22
21
CN301
11
11 PROTECT1
15
15 PROTECT2
5
5 PROTECT3
29
29 VCOM-PWM
26
BACKLIGHT-SW
26
28 BACKLIGHT-ADJ 28
CN3701
CN3701
25 REMOTE
1 P-ON-H2
9 P-ON-H1
CN3702
29 KEY-IN1
(TUNER UNIT)
(TUNER UNIT)
POWER SUPPLY CBA
4 SCL
5 SDA
* TU301
9 SCL
8 SDA
* TU301
DRIVE
IC201,Q203,
Q204,Q205
Either TU301 is used for Power Supply CBA.
CL103A
3 KEY-IN1
D101
POWER
6
5
4
14
CN201
PROTECT3
BACKLIGHT-SW
BACKLIGHT-ADJ
VCOM
TO
INVERTER
BLOCK
DIAGRAM
(CN1001)
IR SENSOR CBA
REMOTE
SENSOR
RS101
CL102
2
5
4
TO
POWER SUPPLY
BLOCK DIAGRAM
CN101
2 REMOTE
5 P-ON+9V
4 KEY-IN1
P-ON-H2
P-ON-H1
PROTECT1
PROTECT2
P-ON+9V
FUNCTION CBA
CL103B
3
KEY SWITCH
[TYPE C]
1. System Control Block Diagram
PL10.3CBLS
JK751
S-VIDEO
-IN
C
Y
9-14
CL701B
5
3
1
2
VIDEO-IN
S-VIDEO-C-IN
S-VIDEO-Y-IN
S-VIDEO-SW-IN
CL701A
5
3
1
2
DIF-OUT1 11
DIF-OUT2 10
IF-AGC 9
(TUNER UNIT)
* TU301
DIF-OUT1 13
DIF-OUT2 12
IF-AGC 14
(TUNER UNIT)
* TU301
Either TU301 is used for Power Supply CBA.
JK731
COMPONENT
-Y-IN
JK732
COMPONENT
-Pb-IN
JK733
COMPONENT
-Pr-IN
JACK CBA
JK752
VIDEO-IN
POWER SUPPLY CBA
WF4
WF2
WF5
WF3
WF6
WF1
VIDEO-IN
S-VIDEO-C-IN
S-VIDEO-Y-IN
S-VIDEO-SW
COM-VIDEO-Y-IN
COM-VIDEO-Pb-IN
COM-VIDEO-Pr-IN
CN302
26 DIF-OUT1
28 DIF-OUT2
24 IF-AGC
CN302
4
6
8
5
15
17
19
CN3702
26
28
24
CN3702
4
6
8
5
15
17
19
DIGITAL MAIN CBA UNIT
DIF-OUT1
DIF-OUT2
IF-AGC
VIDEO-IN
S-VIDEO-C-IN
S-VIDEO-Y-IN
S-VIDEO-SW
COM-VIDEO-Y-IN
COM-VIDEO-Pb-IN
COM-VIDEO-Pr-IN
AUDIO SIGNAL
TO DIGITAL
SIGNAL PROCESS
BLOCK DIAGRAM
VIDEO SIGNAL
2. Video Block Diagram
PL10.3BLV
JACK CBA
9-15
Q873,Q874
DRIVE
SP802
SPEAKER
R-CH
SP801
SPEAKER
L-CH
JK841
DIGITAL
AUDIO-OUT
(COAXIAL)
CN801
SP(L)+ 2
SP(L)- 1
CN802
SP(R)+ 2
SP(R)- 1
CL801
CL802
BUFFER
Q841
PWM
GENERATOR
36
GAIN
CONTROL
GAIN
CONTROL
40
3
Q771
13
3
Q772
Q801
POWER SUPPLY CBA
4
CONTROL LOGIC
PWM
GENERATOR
PWM
GENERATOR
15
28
PWM
GENERATOR
8
5
3
9 10
CONTROL
LOGIC
IC871
(OP AMP)
IC801 (AUDIO AMP)
7
MUTE
2
4
1
5
IC771
(AUDIO SELECTOR)
15
11
12
14
JK872
AUDIO(R)-OUT
Q872
MUTE
CL701A
7
9
1
Q871
CL701B
7 AUDIO(L)-IN
9 AUDIO(R)-IN
JK871
AUDIO(L)-OUT
JK721
HDMIAUDIO(L)-IN
JK722
HDMIAUDIO(R)-IN
JK741
COMPONENTAUDIO(L)-IN
JK742
COMPONENTAUDIO(R)-IN
JK753
AUDIO(L)
-IN
JK754
AUDIO(R)
-IN
WF7
AUDIO(L)-OUT
AUDIO(R)-OUT
AMP(L)-OUT
AMP(R)-OUT
CN302
2 SPDIF
20 AUDIO-MUTE
CN301
2
4
6
8
CN302
10 INPUT1
12 INPUT0
CN302
13 AUDIO(L)
11 AUDIO(R)
CN3702
2
20
CN3701
2
4
6
8
CN3702
10
12
CN3702
13
11
8
7
6
5
8
7
6
5
DIGITAL MAIN CBA UNIT
(L-CH)
15
D/A
(R-CH) CONVERTER
14
IC3801
(D/A CONVERTER)
(L-CH)
D/A
15
(R-CH) CONVERTER
14
IC3802
(D/A CONVERTER)
35
36
33
37
34
DSP
2
40
4
39
3
IC3803
(AUDIO DSP)
SPDIF
LRCLK
BCLK
ADATA2
ACLK
ADATA1
INPUT1
INPUT0
AUDIO-MUTE
AUDIO(L)
AUDIO(R)
TO
DIGITAL
SIGNAL
PROCESS
BLOCK
DIAGRAM
TO
SYSTEM
CONTROL
BLOCK
DIAGRAM
TO
DIGITAL
SIGNAL
PROCESS
BLOCK
DIAGRAM
AUDIO SIGNAL
3. Audio Block Diagram
PL10.3BLA
9-16
7
9
4
6
HDMI-IN3 1
3
10
12
16
15
TMDS-D0(+)
TMDS-D0(-)
TMDS-D1(+)
TMDS-D1(-)
TMDS-D2(+)
TMDS-D2(-)
TMDS-CLOCK(+)
TMDS-CLOCK(-)
SDA
SCL
JK3704
TMDS-D0(+)
7
TMDS-D0(-)
9
TMDS-D1(+)
4
TMDS-D1(-)
6
TMDS-D2(+)
HDMI-IN2 1 TMDS-D2(-)
3
TMDS-CLOCK(+)
10
TMDS-CLOCK(-)
12
SDA
16
SCL
15
JK3702
TMDS-D0(+)
7
TMDS-D0(-)
9
TMDS-D1(+)
4
TMDS-D1(-)
6
TMDS-D2(+)
1
TMDS-D2(-)
HDMI-IN1
3
TMDS-CLOCK(+)
10
TMDS-CLOCK(-)
12
SDA
16
SCL
15
JK3701
TO AUDIO
BLOCK DIAGRAM
TO VIDEO
BLOCK DIAGRAM
TO VIDEO
BLOCK DIAGRAM
AUDIO(L)
AUDIO(R)
BCLK
LRCLK
ACLK
SPDIF
ADATA0
ADATA1
IF-AGC
S-VIDEO-SW
DIF-OUT1
DIF-OUT2
VIDEO-IN
S-VIDEO-C-IN
S-VIDEO-Y-IN
COM-VIDEO-Y-IN
COM-VIDEO-Pb-IN
COM-VIDEO-Pr-IN
DIGITAL MAIN CBA UNIT
B1
B2
C1
C2
D1
D2
A1
A2
A3
B3
A5
B5
C4
C5
B4
A4
B6
A6
A7
B7
A9
B9
C8
C9
B8
A8
B10
A10
A11
B11
M1
M2
AD9
AD12
AD10
AD11
AC10
AD14
A/D
CONVERTER
HDMI
I/F
VIDEO
DECODER
AUDIO
DECODER
AUDIO I/F
DEMODULATOR
/MPEG DECODER
SW
AF7 IF-AGC
C6 S-VIDEO-SW
AE2
AF2
AA3
V3
U3
U1
V1
U2
V2
IC3301 (DIGITAL SIGNAL PROCESS)
DIGITAL
SIGNAL
PROCESS
TP
POL
CPV
OE
STV
C15,C17-19,
C23,C24,D14,
D15,D17-19,
D22,D23
A13-15,A18,
A21-23,B13-15,
B17,B19-23
LVDS TX
W25
W23
Y24
Y23
Y22
AD23
AD24
AE23
AF23
AF22
AE22
AD21
AD22
AF24
AE24
IC3201
(DDR2 SDRAM)
LVDS
RX
B1,B9,C2,C8,
D1,D3,D7,D9,
F1,F9,G2,G8, DATA(0-15)
H1,H3,H7,H9
M2,M3,M7,M8,
N2,N3,N7,N8, ADDESS(0-12)
P2,P3,P7,P8,R2
8
7
10
9
12
11
16
15
14
13
DATA
INPUT
LATCH
LINE BUFFER
FRC
GAMMA
CORRECTOR
DATA
PROCESSING
IC3901 (TINING CONTROLLER)
LVDS
OUTPUT
VIDEO SIGNAL
48
47
46
45
44
43
38
37
36
35
34
33
42
41
63
64
30
31
32
CN3902
23
22
21
20
19
18
13
12
11
10
9
8
16
15
6
5
4
3
1
AUDIO SIGNAL
LLV0(+)
LLV0(-)
LLV1(+)
LLV1(-)
LLV2(+)
LLV2(-)
LLV3(+)
LLV3(-)
LLV4(+)
LLV4(-)
LLV5(+)
LLV5(-)
LLVCLK(+)
LLVCLK(-)
TP
POL
CPV
OE1
STV
LCD MODULE
ASSEMBLY
4. Digital Signal Process Block Diagram
PL10.3BBLD
TO SYSTEM
CONTROL
BLOCK
DIAGRAM
(CN201)
TO POWER
SUPPLY
BLOCK
DIAGRAM
(CN602)
10
11
12
2
Q1931
9-17
CN1001
PROTECT3
BACKLIGHT-SW
BACKLIGHT-ADJ
VCOM
COLD
HOT
Q1932
Q1930
SWITCHING
CN1900
1 +B
3 HOT-GND
4 HOT+15V
HOT CIRCUIT. BE CAREFUL.
11
3
15
8
Q1971
3
4
IC1931
2
3
2
1
Q1970
1
4
IC1930
14
7
5
4
10
2
T1950
Q1621
Q1004,
Q1005
SW
Q1800,Q1815
SW+16V
INV+16V
Q1972
NOTE:
The voltage for parts in hot circuit is measured using
hot GND as a common terminal.
Q1600
2
1
15
16
3
4 DCT
12 VCC
6
5
1
3
OVER VOLTAGE
PROTECTOR
Q1060
6
5
2
3
7
1
OVER VOLTAGE
PROTECTOR
Q1061
Q1111
OVER VOLTAGE
PROTECTOR
OVER VOLTAGE
PROTECTOR
OVER VOLTAGE
PROTECTOR
Q1110
9
10
8
Q1161
OVER VOLTAGE
PROTECTOR
Q1211
14
Q1160
OVER VOLTAGE
PROTECTOR
Q1210
8
7
6
5
8
7
6
5
8
7
6
5
2
4
T1200
1
3
2
4
T1150
1
3
2
4
T1100
1
3
8
7
OVER VOLTAGE
PROTECTOR
CURRENT
CONTROL
SWITCH
Q1550
CURRENT
CONTROL
SWITCH
Q1500
T1050
2
4
13
12
Q1003
DRIVE
Q1551,
Q1552,
Q1553
DRIVE
Q1501,
Q1502,
Q1503
Q1801,Q1802,
Q1803,Q1804
SW+16V
Q1001
8
11
IC1700
(COMPARATOR)
5 6
OSC
PWM
CONTROL
LOGIC
IC1000
(PWM CONTROL)
INVERTER CBA
CN1003
10
CN1200
1
2
CN1150
1
2
CN1100
1
2
CN1050
1
2
LCD MODULE
ASSEMBLY
VCOM
BACK
LIGHT
BACK
LIGHT
BACK
LIGHT
BACK
LIGHT
5. Inverter Block Diagram
PL10.3BLINV
TO
INVERTER
BLOCK
DIAGRAM
(CN1900)
AC601
AC CORD
LINE
FILTER
LINE
FILTER
9-18
3
4
2
1
FEED
BACK
Q631,
D653
19
18
17
16
15
14
13
12
11
COLD
IC601
ERROR
VOLTAGE DET
9
8
7
5
4
3
T601
HOT
Q602
SWITCHING
Q603,
Q604
SW
HOT+15V
BRIDGE
RECTIFIER
D601- D604
POWER SUPPLY CBA
VH
ZCD
OUT
FB
IS
VCC
IC602
SWITCHING
CONTROL
Q601
SWITCHING
CN602
1 ACL
2 HOT-GND
3 HOT-15V
8
1
5
4
3
6
L602
L601
4A/125V
F601
4A/125V
HOT CIRCUIT. BE CAREFUL.
CAUTION !
Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit.
If Main Fuse (F601) is blown , check to see that all components in the power supply
circuit are not defective before you connect the AC plug to the AC power supply.
Otherwise it may cause some components in the power supply circuit to fail.
4A/125V
Q635
+5V REG.
Q634
Q501
SW+16V
3
IC631
+3.3V
REG.
Q636
Q201, Q202,
Q212
SW
2
Q640
SW+5V
Q638,Q639
SWITCHING
Q209, Q213,
D204
SW+16V
Q207,Q208
SWITCHING
Q210
SW+24.5V
Q641,643
SW+5V
Q637,D666
SW+3.3V
Q642
SW+9V
Q401
Q211,D210
SW-6.8V
CN301
10
16
21,22
19,20
13,14
CN201
13
8,9
2
10
12
CAUTION ! : For continued protection against risk of fire,
replace only with same type 4 A, 125V fuse.
ATTENTION : Utiliser un fusible de rechange de même type de 4A, 125V.
P-ON+3V
P-ON+7V
AL+3.3V
P-ON+3.3V
P-ON+5V
LCD-6.8V
LCD+16V
INV+16V
VGH
P-ON+3.3V
CN3701
10
16
21,22
19,20
13,14
CN1001
3
7,8
14
6
4
P-ON-H1
P-ON-H2
PROTECT1
PROTECT2
DIGITAL MAIN CBA UNIT
INVERTER CBA
TO SYSTEM
CONTROL
BLOCK
DIAGRAM
P-ON+9V
AL+33V
P-ON+5V
AL+13V
TUNER+5V
AL+3.3V
P-ON+3V
P-ON+7V
AL+3.3V
P-ON+3.3V
P-ON+5V
LCD+6.8V
LCD+16V
INV+16V
VGH
P-ON+3.3V
NOTE:
The voltage for parts in hot circuit is measured using
hot GND as a common terminal.
6. Power Supply Block Diagram
PL10.3BLP
SCHEMATIC DIAGRAMS / CBA AND TEST POINTS
Standard Notes
WARNING
Many electrical and mechanical parts in this chassis
have special characteristics. These characteristics
often pass unnoticed and the protection afforded by
them cannot necessarily be obtained by using
replacement components rated for higher voltage,
wattage, etc. Replacement parts that have these
special safety characteristics are identified in this
manual and its supplements; electrical components
having such features are identified by the mark “#” in
the schematic diagram and the parts list. Before
replacing any of these components, read the parts list
in this manual carefully. The use of substitute
replacement parts that do not have the same safety
characteristics as specified in the parts list may create
shock, fire, or other hazards.
Notes:
1. Do not use the part number shown on these
drawings for ordering. The correct part number is
shown in the parts list, and may be slightly
different or amended since these drawings were
prepared.
2. All resistance values are indicated in ohms
(K = 103, M = 106).
3. Resistor wattages are 1/4W or 1/6W unless
otherwise specified.
4. All capacitance values are indicated in µF
(P = 10-6 µF).
5. All voltages are DC voltages unless otherwise
specified.
6. This schematic diagrams are masterized version
that should cover the entire PL10.3 chassis models.
Thus some parts in detail illustrated on this
schematic diagrams may vary depend on the
model within the PL10.3 chassis.
Please refer to the parts lists for each models.
7. The Circuit Board layout illustrated on this service
manual is the latest version for this chassis at the
moment of making this service manual.
Depend on the mass production date of each
model, the actual layout of each Board may differ
slightly from this version.
10-1
PL10.3SC
LIST OF CAUTION, NOTES, AND SYMBOLS USED IN THE SCHEMATIC DIAGRAMS ON
THE FOLLOWING PAGES:
1. CAUTION:
CAUTION: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH SAME
TYPE_A,_V FUSE.
ATTENTION: UTILISER UN FUSIBLE DE RECHANGE DE MÊME TYPE DE_A,_V.
2. CAUTION:
Fixed Voltage (or Auto voltage selectable) power supply circuit is used in this unit.
If Main Fuse (F601) is blown, first check to see that all components in the power supply circuit are not
defective before you connect the AC plug to the AC power supply. Otherwise it may cause some components
in the power supply circuit to fail.
3. Note:
1. Do not use the part number shown on the drawings for ordering. The correct part number is shown in the
parts list, and may be slightly different or amended since the drawings were prepared.
2. To maintain original function and reliability of repaired units, use only original replacement parts which are
listed with their part numbers in the parts list section of the service manual.
4. Voltage indications on the schematics are as shown below:
Plug the TV power cord into a standard AC outlet.:
2
1
(Unit: Volt)
3
5.0
Voltage
5.0
Power on mode
Indicates that the voltage
is not consistent here.
5. How to read converged lines
1-D3
Distinction Area
Line Number
(1 to 3 digits)
3
AREA D3
2
Examples:
1. "1-D3" means that line number "1" goes to the line number
"1" of the area "D3".
1
2. "1-B1" means that line number "1" goes to the line number
"1" of the area "B1".
1-B1
AREA B1
1-D3
A
B
C
D
6. Test Point Information
: Indicates a test point with a jumper wire across a hole in the PCB.
: Used to indicate a test point with a component lead on foil side.
: Used to indicate a test point with no test pin.
: Used to indicate a test point with a test pin.
10-2
PL10.3SC
Power Supply 1 Schematic Diagram
CAUTION !
Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit.
If Main Fuse (F601) is blown , check to see that all components in the power supply
circuit are not defective before you connect the AC plug to the AC power supply.
Otherwise it may cause some components in the power supply circuit to fail.
4A/125V
CAUTION ! : For continued protection against risk of fire,
replace only with same type 4 A, 125V fuse.
ATTENTION : Utiliser un fusible de rechange de même type de 4A, 125V.
10-3
NOTE:
The voltage for parts in hot circuit is measured using
hot GND as a common terminal.
PL10.3SCP1
Power Supply 2 Schematic Diagram
10-4
PL10.3SCP2
Power Supply 3 & Jack Schematic Diagram
10-5
PL10.3SCP3
Power Supply 4 Schematic Diagram
10-6
PL10.3SCP4
Inverter Schematic Diagram
NOTE:
The voltage for parts in hot circuit is measured using
hot GND as a common terminal.
10-7
PL10.3SCINV
Function Schematic Diagram
10-8
PL10.3SCF
IR Sensor & Junction Schematic Diagram
10-9
PL10.3SCIR
Digital Main 1 Schematic Diagram [TYPE A]
1 NOTE:
The order of pins shown in this diagram is different from that of actual IC3301.
IC3301 is divided into five and shown as IC3301 (1/5) ~ IC3301 (5/5) in this Digital Main Schematic Diagram Section.
10-10
PL10.3SCD1
Digital Main 2 Schematic Diagram [TYPE A]
1 NOTE:
The order of pins shown in this diagram is different from that of actual IC3301.
IC3301 is divided into five and shown as IC3301 (1/5) ~ IC3301 (5/5) in this Digital Main Schematic Diagram Section.
10-11
PL10.3SCD2
Digital Main 3 Schematic Diagram [TYPE A]
1 NOTE:
The order of pins shown in this diagram is different from that of actual IC3301.
IC3301 is divided into five and shown as IC3301 (1/5) ~ IC3301 (5/5) in this Digital Main Schematic Diagram Section.
10-12
PL10.3SCD3
Digital Main 4 Schematic Diagram [TYPE A]
1 NOTE:
The order of pins shown in this diagram is different from that of actual IC3301.
IC3301 is divided into five and shown as IC3301 (1/5) ~ IC3301 (5/5) in this Digital Main Schematic Diagram Section.
10-13
PL10.3SCD4
Digital Main 5 Schematic Diagram [TYPE A]
1 NOTE:
The order of pins shown in this diagram is different from that of actual IC3301.
IC3301 is divided into five and shown as IC3301 (1/5) ~ IC3301 (5/5) in this Digital Main Schematic Diagram Section.
10-14
PL10.3SCD5
Digital Main 1 Schematic Diagram [TYPE B, TYPE C]
1 NOTE:
The order of pins shown in this diagram is different from that of actual IC3301.
IC3301 is divided into five and shown as IC3301 (1/5) ~ IC3301 (5/5) in this Digital Main Schematic Diagram Section.
10-15
PL10.3_2SCD1
Digital Main 2 Schematic Diagram [TYPE B, TYPE C]
1 NOTE:
The order of pins shown in this diagram is different from that of actual IC3301.
IC3301 is divided into five and shown as IC3301 (1/5) ~ IC3301 (5/5) in this Digital Main Schematic Diagram Section.
10-16
PL10.3_2SCD2
Digital Main 3 Schematic Diagram [TYPE B, TYPE C]
1 NOTE:
The order of pins shown in this diagram is different from that of actual IC3301.
IC3301 is divided into five and shown as IC3301 (1/5) ~ IC3301 (5/5) in this Digital Main Schematic Diagram Section.
10-17
PL10.3_2SCD3
Digital Main 4 Schematic Diagram [TYPE B, TYPE C]
1 NOTE:
The order of pins shown in this diagram is different from that of actual IC3301.
IC3301 is divided into five and shown as IC3301 (1/5) ~ IC3301 (5/5) in this Digital Main Schematic Diagram Section.
10-18
PL10.3_2SCD4
Digital Main 5 Schematic Diagram [TYPE B, TYPE C]
1 NOTE:
The order of pins shown in this diagram is different from that of actual IC3301.
IC3301 is divided into five and shown as IC3301 (1/5) ~ IC3301 (5/5) in this Digital Main Schematic Diagram Section.
10-19
PL10.3_2SCD5
Power Supply CBA & Jack CBA Top View
CAUTION !
Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit.
If Main Fuse (F601) is blown , check to see that all components in the power supply
circuit are not defective before you connect the AC plug to the AC power supply.
Otherwise it may cause some components in the power supply circuit to fail.
NOTE:
The voltage for parts in hot circuit is measured using
hot GND as a common terminal.
BL-ADJ
GND
C210
Q205
J299
Q604
1
R627
R625
HOT+15V
HV
J370
J395
R606
GND
3
R686
J367
CN602
RISK OF FIREREPLACE FUSE AS MARKED
2
1
C655
D645
Q641
Q640
P-ON+5V
D604
C823
L602
C603
A
FH602
SA60
1
C601
R6
01
J323
C831
10-20
F601
AC601
J322
GND
1
GND
D801
D802
J105
AMP+12V
L804
60
CN
CN801
J328
J107
D
J104
AMP+12V
L803
TM601
C694
BC804
BC805
C
C602
HOT
C693
GND
GND
J112
BC802
GND
GND
GND
J114
AMP+12V
BC803
GND
J123
J106
J128
GND
C819
D807
D804 J111
GND
J116
GND
C816
L601
L802
COLD
J143
J144
C832
L801
J110
J142
A-MUTE
D417
D418
J125
J137
PROTECT2
J127
R819
D803
B
GND
R402
J145
D806
ALL3.3V
J139
PROTECT3
ALL3.3V
J130
J340
3.5Vfor1.8V
J135
P-ON-H1
VCOM-PWM
J122
KEY-IN1
J121
J118
J101 CN802
GND
AMP+12V
J136
D414
J117
BL-SW
BL-ADJ
J120
R821
J330
P-ON-H1
Q841
GND
OE2
J119
J131
J115
J134
PROTECT1
J133
P-ON-H2
6.7V
J132
GND
5
D421
GND
D413
J345
J108
P-ON 3.3V
GND
J344
CN101
D6
74
J103
ALL3.3V
29
J102
28
D676
1
ALL+3.3V
J358
ALL+3.3V
GND
J113
R699
R700
TU301
D409
J147
GND
C827
BC841
SPDIF
J151
J343
GND
J152
J129
GND
3.5Vfor1.8V
TUNER
A S
C844
4A/125V
D621
C604
J150
GND
FH601
R685
R683
R603
D602
C676
J176
GND
J164
J172
R605
D603
D666
Q639
J368
GND
J161
GND
GND
D415
J157
J155
C654
P-ON 5V
TUNER 5V
R694
Q801
J160
J159
J354
R682
R691
R693
ALL3.3V
R687
JK711
D670
J153
JK841
J382
GND
P-ON 5V
GND
J286
2
R624
D619
R622
C608
J396
C610
J393
D620
R674
GND
D665
Q642
C657
R692
C303
JS302
GND
Q643
C653
D411
L871
J183
HDMI-L
J170
P-ON-H2
R688
J166
TUNER 5V
D671
HDMI-R
J169
J180
PC-R
R689
J168
P-ON 9V
J207
J341
D410
JK721
6.7V
J171 GND
J174
JK742
R678
Q637
J188
R698
GND
AOUT-R
R673
J184
J194
P-ON 3.3V
R677
GND
C652
AOUT-L
Q872
R780
J191
J186
C639
Q638
J210
OPAMP 9V
R878
JK741
JK871
J200
HDMI-L
J195
SW 9V
J196
C880
GND
AMP 13V
LCD 16V
PROTECT1
J202
C656
JS301
J342
J215
J211
J206
GND
D649
J218
J189
A-OUT-R
JK872
J158
J124
J126
J141
GND
BL-SW
14
CN201
15
J309
J307
J303
Q204
J288
C675
C692
LCD+3.3V
LCD 16V
C220
R210
Q206
J306
J297
GND
J284
GND
D609
R613
C613
IS
J394
C614
C615
D641
C605
29
J148
RESET
J146
KEY-IN1
LCD -6V
R212
Q203
J301
J312
GND
J291
C609 D610
C611
1
D61
GND
D642
D615
D644
C644
D646
J223
C607
D643
C642
D655
R611
R610
R672
JK733
GND
R609
Q601
A-MUTE
J227
R612
17
C691
LCD 16V
6.7V
R626
D601
1
2
GND
Q202
FB
J391
13
D6
12
D404
6.7V
J212
R623
D607
C606
J353
GND
J360
Q603
R621
D616
J238
JK722
CN301
C219
J320
D202
R249
J314
D205
D206
R238
R239
R237
C223
J389
GND
C638
D638
T601
BC601
LOW-VOL PROTECT
J254
OPAMP 9V
R788
R790
R791
J192
PC-L
C306
D302
D301
TUNER 5V
GND
JS303
1
D608
D606
D6
P-ON-H1
J232
R619
R620
C633
Q871
R203
C204
C225
R245
R236
GND
J337
Q210
R235
JS202
OE2
GND
J268
GND
J371
JS630
R646
R639
R637
R638
D6
R242
14
BC603
C645
GND
J361
J315
Q207
R229
R228
R224
R223
D209
R501
GND
J362
GND
GND D657
J363
D632
D633
J364
P-ON 3.3V
J234
D6
R617
3.5Vfor1.8V
COMP-Pb
Q873
R618
BC602
61
C647
J356
V-L
J349
GND
J350
GND
J162
J156
CN302
BC301
J165 VT 31V
2
J154
GND
GND
GND
J246
COMP-L
J213
A-OUT-L
L301
SPDIF
Q771
R771
1
J388
J242
R781
J167
D622
3
D631
D647
J278
J233
COMP-Pr
J229
D303
GND
J187
INPUT0
J173
GND
2
+6.7V
J204
J177
INPUT1
Q772
J178
J175
J199
GND
GND
J346
28
J351
-7V
C771
SEL-R
J182
J203
J357
J226
A-MUTE
SEL-L
SW 9V
J185
GND
+6.7V
V-R
ALL+3.3V
J263
J399
Q874
J205
ALL+3.3V
J348
D639
D635
J216
J217
J190
J347
J225
GND
+15Vfor13VLCD
JK732
A-OUT-MUTE
J214
J222
S-Y
C648
D664
J224
GND
J209
+15Vfor13VLCD
J339
J235
V-R
GND
V-L
J228
J230
VT 31V
1
GND
GND
9
R763
J365
4
IC601
D648
J237
COMP-Y
GND
J355
CL701A
J267
AMP+12V
D6
D673
R636
D662
C640
J149
D659
R665
R635
D654
C650
C637
C632
50
D660
R406
D637
3
Q213
D403
Q636
R695
D407
R407
R662
R660
D658
R663
R661
D412
JK731
1
2
R502
Q635
R664
J352
J319
+15Vfor13VLCD
J290
R657
R666
R667
D675
R650
LCD+16V
R247
R253
R697
GND
J269
-7V
D419
D653
LCD+16V
J377
R2
C646
C631
J383
R696
D207
J300
GND
J316
GND
J317
GND
D652
GND
J387
JS203
R649
R645
GND
J386
J390
ALL+6.0V
R653
J369
Q209
D651
LOW-VOL PROTECT
Q631
D650
TOOL NO.
J381
Q634
GND
D204
GND
J359
R204
JS633
J380
C222
+36V
J379
A
Q201
JS631
R658
J376
LCD+16V
Q208
J264
PROTECT2
Q402
D211
R227
GND
J375
D201
JS201
INV+13V
R254
J384
Q211
+36V
R655
J385
GND
Q401
JK754
10
123456789
R243
J373
D401
D208
D203
R240
J292
LCD -6V
J372
J378
BA01F2F0102 5
A3
D420
GND
J289
J374
J241
PROTECT1
D416
Q501
JK752
JK751
C501
J239
GND
D210
LCD 24V
J298
D667
JK753
C7A3
R405
D405
R244
D406
J366
CL701B
J163
B
9
C224
BA01F2F0102 5
PROTECT3
Power Supply CBA
1
4
4A/125V
GND
Q212
Jack CBA
CAUTION ! : For continued protection against risk of fire,
replace only with same type 4 A, 125V fuse.
ATTENTION : Utiliser un fusible de rechange de même type de 4A, 125V.
J392
DRIVE OUT
Because a hot chassis ground is present in the power supply
circuit, an isolation transformer must be used when repairing.
Also, in order to have the ability to increase the input slowly,
when troubleshooting this type of power supply circuit,
a variable isolation transformer is required.
TM602
E
F
G
BA01F2F01025
Power Supply CBA & Jack CBA Bottom View
Power Supply CBA
R752
C755
C752
R756
R758
C751
R757
C753
R760
R753
R759
R755
JK754
JK751
R751
JK752
JS201
R246
R411
R231
R234
C402
R410
J380
R644
C650
R659
+36V
R658
D419
R648
J264
GND J366
-7V
J269
R652
D654
R668
GND
J371
GND J291
J297
Q206
J306
LCD 16V
C220
C221
Q634
R655
R638
R637
R646
R639
JS630
D204
R233
R232
J390
GND
FB
C675
GND J284
J391
J389
GND
D652
D651
D650
R653
R210
C217
C692
LCD+3.3V
C203
2
R2
50
C632
D403
R695
Q636
R501
Q213
D638
13
C638
D6
D6
D209
12
D610 C609
D609
GND
C608
R622
R624
D619
R407
D660
D407
R657
R666
R242
IC602
C611
D61
1
J396
R663
R660
R406
IS
J394
R613
J370
HV
J393
D659
R665
C640
C647
D404
J364
J149
GND
D662
GND
J361
GND J362
C731
R731
R734
GND J363
D657
D673
R636
D658
R662
D6
61
T601
C615
C614
C613
J392
DRIVE OUT
C610
R625
Q604
R627
HOT+15V
R651
R607
D620
J395
J355
J356
C643
C732
R735
R887
R888
J234
J230
VT 31V
R893
GND
GND
GND
1
P-ON 3.3V
J357
C734
C735
R732
C642
D643
C607
R606
R604
C736
C649
IC631
J224
GND
V-R
V-L
J226
J225
Q873
R877
JK733
R736
J232
LCD 16V
D641
D642
D646
C691
R672
R779
J214
V-L
R778
R790
R791
V-R
C776
R794
R793
R788
R789
C773
C743
R743
R745
R777
C775
R776
J205
J199
GND
J196
R744
R884
C878
1
2
R775
J180
PC-R
R772
J192
PC-L
R773
Q771
R771
R782
R781
HDMI-R
HDMI-L
C872
R785
C742
R874
D411
GND J171
C652
2
J349
GND
J350
GND
C309
R303
R302
CN302
VT 31V
J165
J156
JK711
D301
C303
C723
C721
28
J154
GND
R820
29
J382
GND
C681
L303
C311
C810
C806
1
2
P-ON 5V
R803
R802
J124
J126
D413
GND J132
J141
GND
J113
GND
C682
R805
28
29
J102
ALL3.3V
C845
GND
J344
GND J103
C836
R815
C837
R816
C815
R810
C817
C846
D803
C830
D801
C826
J105
C822 AMP+12V
C821
J104
C825 AMP+12V
C819
D807
R804
C820
C829
C824
R812
R811
BC803
J107
AC601
J106
AMP+12V
BC802
GND
C693
C828
J111
D804
GND
J116
GND
C816
C834
R813
C835
R814
C801
J345
R699
CN301
R700
C683
J115
ALL+3.3V
J134
PROTECT1
J133
P-ON-H2
6.7V
J120
J119
J108
P-ON 3.3V
OE2
J122
J121
BL-SW
BL-ADJ
GND
FH601
F601
J117
VCOM-PWM
J118
J340
J130
C684
J135
KEY-IN1
R894
ALL3.3V
P-ON-H1
R801
R819
ALL3.3V
3.5Vfor1.8V
J139
PROTECT3
J137
PROTECT2
J125
D418
J142
A-MUTE
01
D417
J110
C814
C803
C805
C809
C804
C807
C808
R6
J323
C811 C831
COLD
L601
C601
1
FH602
SA60
GND J131
3.5Vfor1.8V
J129
GND
L302
C310
R308
R301
C307
C301
C302
J358
R722
R844
Q841
C842
R690
R654
J330
P-ON-H1
GND
J145
R402
ALL+3.3V
J151
C305
C308
J148
RESET
J146
KEY-IN1
J152
GND
R305
R307
J343
SPDIF
BC841
R401
R807
R647
L801
R817
L802
C832 J143
C818
J144
R809
R808
R408
R842
R726
R841
R724
R818
R847
C841
C722
C843
R643
R642
R641
J161
D415
Q801
C656
R846
R848
R845
R711
C655
D645
C653
Q641
Q640
P-ON+5V
C654
R795
C703
C704
C702
R716
R714
R712
R687
D670
R682
R683
R685
1
D302
R310
R723
R721
D303
TUNER 5V
L301
J169
J170
R715
C701
R713
D671
C657
Q642
R403
R691
D665
R872
C874
C876
R892
R880
J172
C651
J164
D621
C676
J188
R698
GND
R680
D666
Q639
R679
R675
R676
D603
D602
R605
R603
R882
R886
C885
L871
J183
R876
R746
R742
Q872
C883
R677
Q638
R686
R673
R780
J177
R774
Q772
C772
J187
SW 9V
R787
R783
C744
R784
SW 9V
HDMI-L
J195
R792
C871
JK871
J200
C879
R881
J210
IC871
OPAMP 9V
R878
JK741
R741
R873
C873
R871
C741
R875
R891
C875
R879
R883
C884
OPAMP 9V
R885
C882
C877
D649
GND J206
R674
GND J207
C641
3
CN602
4A/125V
1
CN101
C754
C756
R754
C762
Q401
R404
J385
GND
R412
R681
R241
GND
J317
R228
R229
R225
Q207
R226
J268
J384
Q204
J288
J307
J303
1
GND
TU301
C838
C827
D802
C839
GND
J328
BA01F2F01025
10-21
D676
A
B
C
D
74
D6
5
CN802 J101
GND
C757
R761
C761
C758
R762
C224
R244
D210
J316
GND
J300
GND
D207
R224
J315
GND
R237
R239
C223
R238
D205
D206
J314
GND
Q212
R208
Q203
J301
C208
J312
R222
C209
R205
Q202
R207
R206
C207
GND
R212
C212
R211
J286
22
BC805
L803
L804
42
IC801
C694
R223
R248
Q210
GND J337
JS202
OE2
R235
R236
R245
C225
R201
C206
R202
C216
R213
R215
R214
C213
C210
C214
C201
J299
GND J112
HOT
BC804
J322
GND
CN801
GND J114
C602
GND
GND J123
D414
C724
WF5
PIN 17 OF
CN302
GND J128
R821
D806
TUNER
S A
J127
1
21
D421
R304
R309
R306
J342
R311
JS301
JS302
BC301
WF4
PIN 15 OF
CN302
J136
JK722
GND J155
C304
J147
GND
AMP+12V
C844
D409
JS303
WF6
PIN 19 OF
CN302
CN
60
1
R249
J320
D202
R203
C204
Q205
R219
R218
R217
R216
C218
C219
GND
J163
PROTECT3
BL-ADJ
R209
C202 C215
14
CN201
15
J309
BL-SW
LCD -6V
D601
J159
GND J162
J348
WF7
PIN 13 OF
CN302
J158
R843
JK841
GND J157
C603
R786
TUNER 5V
C823
L602
R725
ALL3.3V
C306
J160
D604
J153
R694
P-ON 5V
WF2
PIN 8 OF
CN302
R688
JK721
R693
JK742
R689
Q643
J166
TUNER 5V
J150
GND
GND
J168
P-ON 9V
R692
J176
GND
C604
J167
SPDIF
J341
D410
P-ON-H2
GND
J354
J368
GND
GND J203
8
J190
WF3
PIN 6 OF
CN302
J184
AOUT-R
16
9
JK872
J173
GND
J174
J175
C880
J189
A-OUT-R
R678
6.7V
Q637
INPUT0
GND
J346
J178
J194
5
GND J186
P-ON 3.3V
GND J367
1
INPUT1
J191
AOUT-L
J182
J202
ALL+3.3V
J211
LCD 16V
4
C648
D664
WF1
PIN 4 OF
CN302
J185
SEL-R
J347
C771
ALL+3.3V
1
IC771
GND
J215
AMP 13V
J204
PROTECT1
J216
SEL-L
J222
S-Y
J217
A-MUTE
COMP-L
J213
A-OUT-L
J218
J352
R635
3
J209
GND
R733
GND J228
J238
Q874
GND J223
J233
COMP-Pr
J229
C733
9
R763
A-OUT-MUTE
Q871
GND J227
J235
J212
J254
A-MUTE
C644
COMP-Pb
J360
6.7V
D655
6.7V
D615
D644
C605
CL701A
P-ON-H1
D637
D648
J237
COMP-Y
JK732
J242
J353
GND
J278
8
C639
E
F
G
D616
GND
R661
D412
J351
JK731
J388
C645
GND
R697
R253
Q635
D647
4
R247
D635
R696
J377
LCD+16V
R664
BC601
J399
R610
C633
17
D6
J246
3.5Vfor1.8V
C606
LOW-VOL PROTECT
Q601
R609
R611
D633
R612
-7V
J365
4
J290
AMP+12V
J263
+6.7V
D632
BC603
S
G
1
D607
R617
R620
R623
+6.7V
D606
R626
R502
D631
BC602
5
R621
J387
1
CL701B
9
D406
R667
J339
J319
+15Vfor13VLCD
J267
+15Vfor13VLCD
8
D
GND
Q209
J386
GND
J381
LOW-VOL PROTECT
D211
C222
J359
R227
J383
C631
C637
D639
D622
GND
1
IC601
4
LCD+16V
2
3
R618
J369
ALL+6.0V
C646
D653
+15Vfor13VLCD
14
D6
R619
Q602
D608
Q603
R649
D401
J375
PROTECT2
D201
Q631
GND
R254
J379
R645
R650
D675
Q402
J376
LCD+16V
JS631
JS633
J239
GND
J374
+36V
C501
J373
J241
PROTECT1
D416
Q501
J378
INV+13V
Q208
R221
R204
8
5 JS203
J372
J292
LCD -6V
JK753
R240
1
4
Q211
D667
IC201
R243
R220
D208
GND J289
D203
J298
LCD 24V
D420
D405
R405
Q201
4A/125V
Jack CBA
NOTE:
The voltage for parts in hot circuit is measured using
hot GND as a common terminal.
Because a hot chassis ground is present in the power supply
circuit, an isolation transformer must be used when repairing.
Also, in order to have the ability to increase the input slowly,
when troubleshooting this type of power supply circuit,
a variable isolation transformer is required.
CAUTION ! : For continued protection against risk of fire,
replace only with same type 4 A, 125V fuse.
ATTENTION : Utiliser un fusible de rechange de même type de 4A, 125V.
CAUTION !
Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit.
If Main Fuse (F601) is blown , check to see that all components in the power supply
circuit are not defective before you connect the AC plug to the AC power supply.
Otherwise it may cause some components in the power supply circuit to fail.
Inverter CBA, Function CBA, IR Sensor CBA & Junction CBA Top View
Because a hot chassis ground is present in the power supply
circuit, an isolation transformer must be used when repairing.
Also, in order to have the ability to increase the input slowly,
when troubleshooting this type of power supply circuit,
a variable isolation transformer is required.
Function CBA
NOTE:
The voltage for parts in hot circuit is measured using
hot GND as a common terminal.
Junction CBA [TYPE A, TYPE B]
Not Used
IR Sensor CBA
Not Used
Inverter CBA
10-22
BA01F2F01031
Inverter CBA, Function CBA, IR Sensor CBA & Junction CBA Bottom View
Because a hot chassis ground is present in the power supply
circuit, an isolation transformer must be used when repairing.
Also, in order to have the ability to increase the input slowly,
when troubleshooting this type of power supply circuit,
a variable isolation transformer is required.
NOTE:
The voltage for parts in hot circuit is measured using
hot GND as a common terminal.
Junction CBA [TYPE A, TYPE B]
Not Used
IR Sensor CBA
Not Used
Function CBA
Inverter CBA
10-23
BA01F2F01031
WAVEFORMS
WF1 ~ WF7 = Waveforms to be observed at
Waveform check points.
(Shown in Schematic Diagram.)
Input: NTSC Color Bar Signal (with 1kHz Audio Signal)
WF1
Pin 4 of CN302
CVBS
WF2
0.2V
WF6
20µs
0.2V
20µs
AUDIO
0.2V
20µs
Pin 19 of CN302
VIDEO-Pr
WF7
0.2V
Pin 17 of CN302
VIDEO-Pb
Pin 6 of CN302
S-VIDEO-C
WF4
20µs
Pin 8 of CN302
S-VIDEO-Y
WF3
WF5
0.2V
20µs
Pin 13 of CN302
0.1V
0.5ms
Pin 15 of CN302
VIDEO-Y
0.2V
20µs
11-1
LC8NWF1
12-1
AC601
AC CORD
AUDIO(R)
-OUT
AUDIO(L)
-OUT
DIGITAL
AUDIO-OUT
(COAXIAL)
HDMIAUDIO(R)-IN
HDMIAUDIO(L)-IN
COMPONENTAUDIO(R)-IN
COMPONENTAUDIO(L)-IN
COMPONENT
-Pr-IN
COMPONENT
-Pb-IN
COMPONENT
-Y-IN
CL3702
GND
SPDIF
GND
VIDEO-IN
S-VIDEO-SW
S-VIDEO-C-IN
GND
S-VIDEO-Y-IN
GND
INPUT1
AUDIO(R)
INPUT0
AUDIO(L)
GND
COM-VIDEO-Y-IN
GND
COM-VIDEO-Pb-IN
GND
COM-VIDEO-Pr-IN
AUDIO-MUTE
SDA
SCL
RESET
IF-AGC
GND
DIF-OUT1
GND
DIF-OUT2
KEY-IN1
CN302
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
CN3702
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
CL3701
CN3701
1
P-ON-H2
AUDIO(L)-OUT 2
3
GND
AUDIO(R)-OUT 4
PROTECT3
5
AMP(L)-OUT
6
7
GND
AMP(R)-OUT
8
P-ON-H1
9
10
P-ON+3V
11
PROTECT1
GND
12
P-ON+5V
13
P-ON+5V
14
PROTECT2
15
P-ON+7V
16
GND
17
18
GND
19
P-ON+3.3V
20
P-ON+3.3V
21
AL+3.3V
22
AL+3.3V
23
GND
24
OE2
25
REMOTE
BACKLIGHT-SW 26
27
LED1(NU)
BACKLIGHT-ADJ 28
VCOM-PWM 29
CN301
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
1
CL801
2
1
CL802
2
CN801
SP(L)SP(L)+
CN802
SP(R)SP(R)+
TU301 TUNER UNIT
SP802
SPEAKER
R-CH
SP801
SPEAKER
L-CH
POWER SUPPLY CBA
CN101
1
2
3
4
5
CL701A
1
2
3
4
5
6
7
8
9
GND
REMOTE
AL+3.3V
KEY-IN1
P-ON+9V
CL701
S-VIDEO-Y-IN
S-VIDEO-SW
S-VIDEO-C-IN
GND
VIDEO-IN
GND
AUDIO(L)-IN
GND
AUDIO(R)-IN
1
2
3
4
CL201
GND
INV+16V
GND
BACKLIGHT-ADJ
BACKLIGHT-SW
PROTECT3
GND
LCD+16V
LCD+16V
VGH
GND
P-ON+3.3V
LCD-6.8V
VCOM
GND
CN602
+B 1
HOT-GND 2
HOT+15V 3
CN201
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
DIGITAL MAIN CBA UNIT
CL102A
1
2
3
4
5
CBA
CN1003
1
2
3
4
5
6
7
8
9
10
CBA 11
CN1200
1
2
CN1150
1
2
CN1100
1
2
CN1050
1
2
JUNCTION CBA
CN151
1
2
3
4
5
CL701B
1
2
3
4
JACK
5
6
7
8
9
INVERTER
CN1900
+B
NU
HOT-GND
HOT+15V
CN1001
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
CL102
GND
REMOTE
AL+3.3V
KEY-IN1
P-ON+9V
S-VIDEO
-IN
AUDIO(R)
-IN
AUDIO(L)
-IN
VIDEO-IN
CL1003
GND
LCD+16V
LCD+16V
VGH
GND
P-ON+3.3V
P-ON+3.3V
LCD-6.8V
GND
VCOM
GND
CL103A
1
2
3
IR SENSOR CBA
CL102B
1
2
3
4
5
LCD MODULE
ASSEMBLY
BACK
LIGHT
BACK
LIGHT
BACK
LIGHT
BACK
LIGHT
CL103
AL+3.3V
GND
KEY-IN1
CL3902
STV
XAO
OE1
CPV
POL
TP
GND
LLV5(-)
LLV5(+)
LLV4(-)
LLV4(+)
LLV3(-)
LLV3(+)
GND
LLVCLK(-)
LLVCLK(+)
GND
LLV2(-)
LLN2(+)
LLV1(-)
LLV1(+)
LLV0(-)
LLV0(+)
GND
HDMICONNECTOR-3
HDMICONNECTOR-2
HDMICONNECTOR-1
FUNCTION CBA
CL103B
1
2
3
CN3902
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
[TYPE A, TYPE B]
WIRING DIAGRAM
PL10.3AWI
12-2
AC601
AC CORD
AUDIO(R)
-OUT
AUDIO(L)
-OUT
DIGITAL
AUDIO-OUT
(COAXIAL)
HDMIAUDIO(R)-IN
HDMIAUDIO(L)-IN
COMPONENTAUDIO(R)-IN
COMPONENTAUDIO(L)-IN
COMPONENT
-Pr-IN
COMPONENT
-Pb-IN
COMPONENT
-Y-IN
CL3702
GND
SPDIF
GND
VIDEO-IN
S-VIDEO-SW
S-VIDEO-C-IN
GND
S-VIDEO-Y-IN
GND
INPUT1
AUDIO(R)
INPUT0
AUDIO(L)
GND
COM-VIDEO-Y-IN
GND
COM-VIDEO-Pb-IN
GND
COM-VIDEO-Pr-IN
AUDIO-MUTE
SDA
SCL
RESET
IF-AGC
GND
DIF-OUT1
GND
DIF-OUT2
KEY-IN1
CN302
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
CN3702
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
CL3701
CN3701
1
P-ON-H2
AUDIO(L)-OUT 2
3
GND
AUDIO(R)-OUT 4
PROTECT3
5
AMP(L)-OUT
6
7
GND
AMP(R)-OUT
8
P-ON-H1
9
10
P-ON+3V
11
PROTECT1
GND
12
P-ON+5V
13
P-ON+5V
14
PROTECT2
15
P-ON+7V
16
GND
17
18
GND
19
P-ON+3.3V
20
P-ON+3.3V
21
AL+3.3V
22
AL+3.3V
23
GND
24
OE2
25
REMOTE
BACKLIGHT-SW 26
27
LED1(NU)
BACKLIGHT-ADJ 28
VCOM-PWM 29
CN301
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
1
CL801
2
1
CL802
2
CN801
SP(L)SP(L)+
CN802
SP(R)SP(R)+
TU301 TUNER UNIT
SP802
SPEAKER
R-CH
SP801
SPEAKER
L-CH
POWER SUPPLY CBA
CN101
1
2
3
4
5
CL701A
1
2
3
4
5
6
7
8
9
GND
REMOTE
AL+3.3V
KEY-IN1
P-ON+9V
CL701
S-VIDEO-Y-IN
S-VIDEO-SW
S-VIDEO-C-IN
GND
VIDEO-IN
GND
AUDIO(L)-IN
GND
AUDIO(R)-IN
1
2
3
4
CL201
GND
INV+16V
GND
BACKLIGHT-ADJ
BACKLIGHT-SW
PROTECT3
GND
LCD+16V
LCD+16V
VGH
GND
P-ON+3.3V
LCD-6.8V
VCOM
GND
CN602
+B 1
HOT-GND 2
HOT+15V 3
CN201
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
DIGITAL MAIN CBA UNIT
CL103A
1
2
3
CBA
CN1003
1
2
3
4
5
6
7
8
9
10
11
CBA
CN1200
1
2
CN1150
1
2
CN1100
1
2
CN1050
1
2
IR SENSOR CBA
CL102
1
2
3
4
5
CL701B
1
2
3
4
JACK
5
6
7
8
9
INVERTER
CN1900
+B
NU
HOT-GND
HOT+15V
CN1001
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
CL103
AL+3.3V
GND
KEY-IN1
S-VIDEO
-IN
AUDIO(R)
-IN
AUDIO(L)
-IN
VIDEO-IN
CL1003
GND
LCD+16V
LCD+16V
VGH
GND
P-ON+3.3V
P-ON+3.3V
LCD-6.8V
GND
VCOM
GND
FUNCTION CBA
CL103B
1
2
3
LCD MODULE
ASSEMBLY
BACK
LIGHT
BACK
LIGHT
BACK
LIGHT
BACK
LIGHT
CL3902
STV
XAO
OE1
CPV
POL
TP
GND
LLV5(-)
LLV5(+)
LLV4(-)
LLV4(+)
LLV3(-)
LLV3(+)
GND
LLVCLK(-)
LLVCLK(+)
GND
LLV2(-)
LLN2(+)
LLV1(-)
LLV1(+)
LLV0(-)
LLV0(+)
GND
CN3902
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
HDMICONNECTOR-3
HDMICONNECTOR-2
HDMICONNECTOR-1
[TYPE C]
PL10.3CWI
EXPLODED VIEWS
Cabinet
32PFL3505D/F7 (Serial No. : YA1A, YA2A, YA4A),
32PFL3515D/F7 (Serial No. : YA1A)
32PFL3505D/F7 (Serial No. : DS1A, DS2A, DS3A, DS4A, DS8A, DS9A)
See Electrical Parts List
for parts with this mark.
B24
32PFL3505D/F7 (Serial No. : YA1A, YA2A, YA4A),
32PFL3515D/F7 (Serial No. : YA1A)
A1
Rear Assembly
B36
B24
B24
Inverter CBA
L2
A17
B36
A18
L2
L1
L1
SP801
CL801
L1
CL802
L2
B13
L8
B8
SP802
L1
B24
L3
A10
B14
B8
LCD1
L7
L8
Function CBA
L7
CL701
L1
Junction CBA
CL103
S5
L8
CL1003
CL102
A16
L3
CL201
L2
A3
L1
L8
B43
Jack CBA
L1
L8
L1
S5
L16
L1
B11
A4
Digital Main CBA Unit
IR Sensor CBA L14
L8
L8
L3
CL3702
CL3701
TYPE A,
TYPE B
L8
L8
Power Supply CBA
CL3902
B44
B27
AC601
Stand Assembly
L9
L8
B1
L6
32PFL3505D/F7 (Serial No. : DS1A, DS2A, DS3A, DS4A, DS8A, DS9A)
A13
13-1
PL10.3CEX
Packing
32PFL3505D/F7 (Serial No. : DS1A, DS2A, DS3A, DS4A, DS8A, DS9A)
L9
X4
X6
X8
X12
X10
X2
S5
X13
S5
S2
X3
Tape
Stand Assembly
X9
X1
32PFL3505D/F7 (Serial No. : YA1A, YA2A, YA4A),
32PFL3515D/F7 (Serial No. : YA1A)
X13
S6
L9
X2
X6
X8
X10 X12
X4
S4
S5
S5
Packing Tape
X1
S3
X3
32PFL3505D/F7 (Serial No. : YA1A, YA2A, YA4A),
32PFL3515D/F7 (Serial No. : YA1A)
S5
FR
ON
T
FR
ON
T
Some Ref. Numbers are
not in sequence.
Packing Tape
S1
13-2
PL10.3PEX
PARTS LIST [32PFL3505D/F7 (Serial No. : DS1A)]
Mechanical Parts
PRODUCT SAFETY NOTE: Products marked with a
# have special characteristics important to safety.
Before replacing any of these components, read
carefully the product safety notice in this service
manual. Don't degrade the safety of the product
through improper servicing.
Ref. No.
Description
Part No.
X6
QUICK START GUIDE A01F2UH
1EMN25660
X8
CHILD SAFETY SHEET A91H2UH
1EMN24526
X9
CONNECTION GUIDE A91F2UH
1EM325921B
X10
REGISTRATION CARD(PHILIPS) A01F2UH
1EMN25799B
X12
WALL MOUNT INSTRUCTION A01F2UH
1EMN25659
X13
CABLE MANAGEMENT TIE(BLACK) A01F2UH 1EM431197
NOTE: Parts that are not assigned part numbers
(---------) are not available.
Ref. No.
Description
Part No.
STAND ASSEMBLY A91F2UH
1ESA19912
REAR ASSEMBLY A01F2UH
1ESA23041
A1
FRONT CABINET A91F2UH
1EM023525
A3
FUNCTION KNOB A91H2UH
1EM222865
A4
SENSOR LED LENS A91H2UH
1EM325697
A13
JACK HOLDER A01F2UH
1EM124273
A16
KNOB FRAME A01F2UH
1EM327217
A18
ENERGY STAR LABEL A91F2UH
----------
B1
SHIELD BOX A01F2UH
1EM224323
B8
SPEAKER HOLDER A91F2UH
1EM123393E
B24
CLOTH 10X150XT1.0
1EM421092
B27
GASKET A8AF0UH
1EM425861
B36
CLOTH(30X50XT1.0) 30X50XT1.0
1EM429138
B44
THERMOSTAR TMS-L-2(12*12HC)
XK10000X4003
CL201
WIRE ASSEMBLY 15PIN FFC 15PIN 140MM
WX1A94F0-104
CL801
WIRE ASSEMBLY 2PIN 2PIN/310MM/CORE
WX1A01F2-004
CL802
WIRE ASSEMBLY 2PIN 2PIN/110MM/CORE
WX1A01F2-003
CL1003
WIRE ASSEMBLY 11PIN FFC 11PIN 129MM
WX1A91F6-101
CL3701
WIRE ASSEMBLY 29PIN FFC 29PIN 50MM
WX1A94F0-101
CL3702
WIRE ASSEMBLY 29PIN FFC 29PIN 50MM
WX1A94F0-101
CL3902
WIRE ASSEMBLY 24PIN FFC 24PIN 117.5MM
WX1A91F6-102
L1
SCREW P-TIGHT M4X14 BIND HEAD+BLK
GBHP4140
L2
SCREW P-TIGHT 3X10 BIND HEAD+
GBHP3100
L6
SCREW S-TIGHT M3X8 BIND HEAD+
GBHS3080
L7
DOUBLE SEMS SCREW M4X10 + BLK
FPH34100
L8
ASSEMBLED SCREW ( D9 M3X6 ) A71F0UH
1EM424392B
L14
SCREW P-TIGHT M3X8 BIND HEAD+ BLK
GBHP3080
L16
SCREW TAP TIGHT M3X10 BIND HEAD+BLK
NI
GBHS3100
LCD1
LCD MODULE CMO 8BIT A GRADE
UJ32MXB
SP801
SPEAKER MAGNETIC S0412F06A
DSD0809XQ006
SP802
SPEAKER MAGNETIC S0412F06A
DSD0809XQ006
PACKING
S1
CARTON A01F2UH
1EM430617
S2
STYROFOAM TOP A91F2UH
1EM024025
S3
STYROFOAM BOTTOM A91F2UH
1EM024026
S4
SET BAG (900X850) A8AFFUH
1EM324904A
S5
SERIAL NO. LABEL A01P0UH
----------
S6
STAND BAG A94F0UH
1EM428757
ACCESSORIES
L9
STAND SCREW KIT A91F2UH
1ESA19986
X1
BAG POLYETHYLENE 235X365XT0.03
0EM408420A
X2#
OWNERS MANUAL A01F2UH
1EMN25539
X3
REMOTE CONTROL TRANSMITTER YKF259- URMT34JHG001
001
X4
BATTERY R03-B500/01S
20100210
XB0M451CZB01
14-1
A01F2CA
Electrical Parts
PRODUCT SAFETY NOTE: Products marked with a
# have special characteristics important to safety.
Before replacing any of these components, read
carefully the product safety notice in this service
manual. Don't degrade the safety of the product
through improper servicing.
Ref. No.
NOTES:
1. Parts that are not assigned part numbers (---------)
are not available.
2. Tolerance of Capacitors and Resistors are noted
with the following symbols.
C.....±0.25%
D.....±0.5%
F.....±1%
G.....±2%
J......±5%
K.....±10%
M.....±20%
N.....±30%
Z.....+80/-20%
DIGITAL MAIN CBA UNIT
Ref. No.
Description
DIGITAL MAIN CBA UNIT
Part No.
A01F2MMA-006
MPW CBA
Ref. No.
Description
Part No.
MPW CBA
Consists of the following:
A01F2MPWS001
POWER SUPPLY CBA(MPW-A)
JACK CBA(MPW-B)
-------------------
POWER SUPPLY CBA(MPW-A)
Ref. No.
Description
POWER SUPPLY CBA(MPW-A)
Consists of the following:
Part No.
----------
CAPACITORS
Description
Part No.
C501
ELECTROLYTIC CAP. 100µF/25V M
CE1EMASDL101
C601#
CAP METALIZED FILM 0.22µF/300V K 3.5MM
CT2F224DC004
C602#
CAP METALIZED FILM 0.22µF/300V K 3.5MM
CT2F224DC004
C605
CAP ELECTROLYTIC 470µF/200V M
CA2D471DYG07
C606
POLYESTER FILM CAP. (PB FREE) 0.0015µF/
100V J
CA2A152DT018
C607#
CERAMIC CAP. 330pF/2KV
CA3D331PAN04
C608
POLYESTER FILM CAP. (PB FREE) 0.001µF/
100V J
CA2A102DT018
C609
ELECTROLYTIC CAP. 47µF/50V M
CE1JMASDL470
C610
ELECTROLYTIC CAP. 100µF/50V M
CE1JMASDL101
C611
CAP CERAMIC (AX) 0.1µF/50V/F/Z
CA1J104TU062
C613
CAP CERAMIC (AX) 33pF/50V/CH/J
CA1J330TU059
C614
CAP CERAMIC (AX) 0.022µF/50V/B/K
CA1J223TU061
C615
CAP CERAMIC (AX) 3300pF/50V/B/K
CA1J332TU061
C631
ELECTROLYTIC CAP. 1000µF/25V M
CE1EMZNDL102
C632
ELECTROLYTIC CAP. 220µF/25V M
CE1EMASDL221
C633
CAP ALUMINUM ELECTOLYTIC 2200µF/6.3V
M
CE0KMZNDL222
C637
CERAMIC CAP. 1500pF/2KV
CA3D152PAN04
C638
ELECTROLYTIC CAP. 220µF/50V M
CE1JMASDL221
C639
ELECTROLYTIC CAP. 1000µF/35V M
CE1GMZADL102
C640
ELECTROLYTIC CAP. 1µF/50V M
CE1JMASDL1R0
C642
ELECTROLYTIC CAP. 1µF/50V M
CE1JMASDL1R0
C643
CHIP CERAMIC CAP.(1608) B K 1µF/10V
CHD1AK30B105
C644
ELECTROLYTIC CAP 3300µF/16V M
CE1CMZNDL332
C645
CAP ALUMINUM ELECTOLYTIC 2200µF/6.3V
M
CE0KMZNDL222
C646
POLYESTER FILM CAP. (PB FREE) 0.0022µF/
100V J
CA2A222DT018
C648
ELECTROLYTIC CAP. 100µF/10V M
CE1AMASDL101
C649
CHIP CERAMIC CAP.(1608) B K 0.1µF/25V
CHD1EK30B104
C650
POLYESTER FILM CAP. (PB FREE) 0.022µF/
100V J
CA2A223DT018
C652
ELECTROLYTIC CAP. 1000µF/6.3V M
CE0KMASDL102
C653
ELECTROLYTIC CAP. 220µF/10V M
CE1AMASDL221
C654
ELECTROLYTIC CAP. 220µF/10V M
CE1AMASDL221
C656
ELECTROLYTIC CAP. 100µF/16V M
CE1CMASDL101
C201
CHIP CERAMIC CAP.(1608) F Z 0.1µF/25V
CHD1EZ30F104
C657
ELECTROLYTIC CAP. 22µF/50V M
CE1JMASDL220
C202
CHIP CERAMIC CAP.(1608) F Z 0.1µF/25V
CHD1EZ30F104
C676
ELECTROLYTIC CAP. 2.2µF/50V M
CE1JMASDL2R2
C203
CHIP CERAMIC CAP.(1608) F Z 0.1µF/25V
CHD1EZ30F104
C681
CHIP CERAMIC CAP.(1608) F Z 0.1µF/25V
CHD1EZ30F104
CHIP CERAMIC CAP.(1608) F Z 0.1µF/25V
CHD1EZ30F104
C204
ELECTROLYTIC CAP. 2.2µF/50V M
CE1JMASDL2R2
C682
C207
CHIP CERAMIC CAP.(1608) B K 0.1µF/16V
CHD1CK30B104
C683
CHIP CERAMIC CAP.(1608) F Z 0.1µF/25V
CHD1EZ30F104
C210
ELECTROLYTIC CAP. 22µF/50V M
CE1JMASDL220
C684
CHIP CERAMIC CAP.(1608) F Z 0.1µF/25V
CHD1EZ30F104
CHD1JJ3CH102
C691#
SAFTY CAP. 1000pF/250V KX
CA2E102MR101
SAFTY CAP. 1000pF/250V KX
CA2E102MR101
CHIP CERAMIC CAP.(1608) B K 2.2µF/10V
CHD1AK30B225
C216
CHIP CERAMIC CAP.(1608) CH J 1000pF/50V
C217
CHIP CERAMIC CAP.(1608) B K 0.1µF/16V
CHD1CK30B104
C693#
C218
CHIP CERAMIC CAP.(1608) B K 1µF/25V
CHD1EK30B105
C723
C219
ELECTROLYTIC CAP. 47µF/25V M
CE1EMASDL470
C724
CHIP CERAMIC CAP.(1608) B K 2.2µF/10V
CHD1AK30B225
CHIP CERAMIC CAP. CH J 39pF/50V
CHD1JJ3CH390
C221
CHIP CERAMIC CAP.(1608) B K 0.01µF/50V
CHD1JK30B103
C731
C222
ELECTROLYTIC CAP. 470µF/25V M
CE1EMASDL471
C732
CHIP CERAMIC CAP. CH J 39pF/50V
CHD1JJ3CH390
C223
ELECTROLYTIC CAP. 22µF/50V M
CE1JMASDL220
C733
CHIP CERAMIC CAP. CH J 39pF/50V
CHD1JJ3CH390
C224
ELECTROLYTIC CAP. 10µF/50V M
CE1JMASDL100
C734
CHIP RES.(1608) 1/10W 0 Ω
RRXAZR5Z0000
CHD1EZ30F104
C735
CHIP RES.(1608) 1/10W 0 Ω
RRXAZR5Z0000
CHIP RES.(1608) 1/10W 0 Ω
RRXAZR5Z0000
CHD1AK30B225
C302
CHIP CERAMIC CAP.(1608) F Z 0.1µF/25V
C303
ELECTROLYTIC CAP. 330µF/10V M
CE1AMASDL331
C736
C305
CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V
CHD1JZ30F104
C743
CHIP CERAMIC CAP.(1608) B K 2.2µF/10V
C306
ELECTROLYTIC CAP. 1µF/50V M
CE1JMASDL1R0
C744
CHIP CERAMIC CAP.(1608) B K 2.2µF/10V
CHD1AK30B225
ELECTROLYTIC CAP. 100µF/16V M
CE1CMASDL101
C307
CHIP CERAMIC CAP.(1608) CH J 47pF/50V
CHD1JJ3CH470
C771
C308
CHIP CERAMIC CAP.(1608) CH J 47pF/50V
CHD1JJ3CH470
C772
CHIP CERAMIC CAP.(1608) F Z 0.1µF/25V
CHD1EZ30F104
C309
CHIP CERAMIC CAP.(1608) B K 0.1µF/25V
CHD1EK30B104
C775
CHIP CERAMIC CAP.(1608) CH J 100pF/50V
CHD1JJ3CH101
C310
CHIP CERAMIC CAP.(1608) CH J 47pF/50V
CHD1JJ3CH470
C776
CHIP CERAMIC CAP.(1608) CH J 100pF/50V
CHD1JJ3CH101
CHD1JJ3CH470
C801
CHIP CERAMIC CAP.(1608) B K 1µF/25V
CHD1EK30B105
C803
CHIP CERAMIC CAP.(1608) B K 0.47µF/25V
CHD1EK30B474
C311
CHIP CERAMIC CAP.(1608) CH J 47pF/50V
20091113
14-2
A01F2EL
Ref. No.
Description
Part No.
Ref. No.
Description
Part No.
C804
CHIP CERAMIC CAP.(1608) B K 0.1µF/25V
CHD1EK30B104
D203
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
C805
CHIP CERAMIC CAP.(1608) CH J 1000pF/50V
CHD1JJ3CH102
D204
IC SHUNT REGULATOR KIA431-AT/P
NSZBA0TJY036
C806
CHIP CERAMIC CAP.(1608) B K 0.47µF/25V
CHD1EK30B474
D205
DIODE ZENER 24BSC-T26
NDTC024BST26
C807
CHIP CERAMIC CAP.(1608) B K 0.1µF/25V
CHD1EK30B104
D206
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
C808
CHIP CERAMIC CAP.(1608) CH J 1000pF/50V
CHD1JJ3CH102
D207
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
C809
CHIP CERAMIC CAP.(1608) B K 1µF/25V
CHD1EK30B105
D208
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
C810
CHIP CERAMIC CAP.(1608) B K 1µF/25V
CHD1EK30B105
D209
DIODE ZENER 39BSB-T26
NDTB039BST26
C814
CHIP CERAMIC CAP.(1608) B K 1µF/25V
CHD1EK30B105
D210
DIODE ZENER 6V2BSB-T26
NDTB6R2BST26
C815
CHIP CERAMIC CAP.(1608) B K 1µF/25V
CHD1EK30B105
D211
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
C816
ELECTROLYTIC CAP. 10µF/50V M
CE1JMASDL100
D401
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
C817
CHIP CERAMIC CAP.(1608) B K 1µF/25V
CHD1EK30B105
D404
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
C818
CHIP CERAMIC CAP.(1608) B K 0.1µF/25V
CHD1EK30B104
D405
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
C819
ELECTROLYTIC CAP. 10µF/50V M
CE1JMASDL100
D406
DIODE ZENER 15BSB-T26
NDTB015BST26
C820
CHIP CERAMIC CAP.(1608) B K 0.47µF/25V
CHD1EK30B474
D407
DIODE ZENER 10BSB-T26
NDTB010BST26
C821
CHIP CERAMIC CAP.(1608) B K 0.1µF/25V
CHD1EK30B104
D409
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
C822
CHIP CERAMIC CAP.(1608) CH J 1000pF/50V
CHD1JJ3CH102
D410
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
C823
ELECTROLYTIC CAP. 1000µF/25V M
CE1EMZNDL102
D411
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
C824
CHIP CERAMIC CAP.(1608) B K 0.47µF/25V
CHD1EK30B474
D412
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
C825
CHIP CERAMIC CAP.(1608) B K 0.1µF/25V
CHD1EK30B104
D413
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
C826
CHIP CERAMIC CAP.(1608) CH J 1000pF/50V
CHD1JJ3CH102
D414
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
C827
ELECTROLYTIC CAP. 10µF/50V M
CE1JMASDL100
D415
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
C828
CHIP CERAMIC CAP.(1608) B K 1µF/25V
CHD1EK30B105
D416
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
C829
CHIP CERAMIC CAP.(1608) B K 1µF/25V
CHD1EK30B105
D417
DIODE ZENER 3V9BSB-T26
NDTB3R9BST26
C831
ELECTROLYTIC CAP. 10µF/50V M
CE1JMASDL100
D418
DIODE ZENER 3V9BSB-T26
NDTB3R9BST26
C834
CHIP CERAMIC CAP.(1608) B K 0.47µF/16V
CHD1CK30B474
D419
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
C835
CHIP CERAMIC CAP.(1608) CH J 1000pF/50V
CHD1JJ3CH102
D420
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
C836
CHIP CERAMIC CAP.(1608) B K 0.47µF/16V
CHD1CK30B474
D421
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
C837
CHIP CERAMIC CAP.(1608) CH J 1000pF/50V
CHD1JJ3CH102
D601#
DIODE GENERAL PURPOSE 1N5406-BU
NDLZ1N5406BU
C838
CHIP CERAMIC CAP.(1608) CH J 470pF/50V
CHD1JJ3CH471
D602#
DIODE GENERAL PURPOSE 1N5406-BU
NDLZ1N5406BU
C839
CHIP CERAMIC CAP.(1608) CH J 470pF/50V
CHD1JJ3CH471
D603#
DIODE GENERAL PURPOSE 1N5406-BU
NDLZ1N5406BU
C841
CHIP CERAMIC CAP. F Z 1µF/10V
CHD1AZ30F105
D604#
DIODE GENERAL PURPOSE 1N5406-BU
NDLZ1N5406BU
C842
CHIP CERAMIC CAP. F Z 1µF/10V
CHD1AZ30F105
D607
DIODE ZENER 11BSB-T26
NDTB011BST26
C843
CHIP CERAMIC CAP.(1608) B K 0.01µF/50V
CHD1JK30B103
D608#
DIODE ZENER 27BSB-T26
NDTB027BST26
C844
ELECTROLYTIC CAP. 10µF/50V M
CE1JMASDL100
D609#
DIODE ZENER 27BSB-T26
NDTB027BST26
C845
CHIP CERAMIC CAP.(1608) CH J 470pF/50V
CHD1JJ3CH471
D610
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
C846
CHIP CERAMIC CAP.(1608) CH J 470pF/50V
CHD1JJ3CH471
D612#
DIODE FR104-B
NDLZ000FR104
C871
CHIP CERAMIC CAP.(1608) B K 3300pF/50V
CHD1JK30B332
D613
DIODE FR104-B
NDLZ000FR104
C872
CHIP CERAMIC CAP.(1608) B K 3300pF/50V
CHD1JK30B332
D614#
DIODE FAST RECOVERY FR103-B/P
NDWZ0FR103BP
C873
CHIP CERAMIC CAP.(1608) B K 2.2µF/10V
CHD1AK30B225
D615#
DIODE ZENER 39BSB-T26
NDTB039BST26
C874
CHIP CERAMIC CAP.(1608) B K 2.2µF/10V
CHD1AK30B225
D616#
DIODE ZENER 27BSB-T26
NDTB027BST26
C875
CHIP CERAMIC CAP.(1608) CH J 100pF/50V
CHD1JJ3CH101
D617
DIODE FAST RECOVERY FR103-B/P
NDWZ0FR103BP
C876
CHIP CERAMIC CAP.(1608) CH J 100pF/50V
CHD1JJ3CH101
D619
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
C877
CHIP CERAMIC CAP.(1608) B K 6800pF/50V
CHD1JK30B682
D622#
DIODE FAST RECOVERY FR103-B/P
NDWZ0FR103BP
C878
CHIP CERAMIC CAP.(1608) B K 6800pF/50V
CHD1JK30B682
D631
DIODE FR154
NDLZ000FR154
C879
CHIP CERAMIC CAP.(1608) F Z 0.1µF/25V
CHD1EZ30F104
D632
DIODE FR104-B
NDLZ000FR104
C880
ELECTROLYTIC CAP. 100µF/16V M
CE1CMASDL101
D633
DIODE FAST RECOVERY FR151-B/P
NDWZ0FR151BP
C882
CHIP CERAMIC CAP.(1608) B K 2.2µF/10V
CHD1AK30B225
D635
DIODE ZENER 24BSB-T26
NDTB024BST26
NDLZ000FR154
C883
CHIP CERAMIC CAP.(1608) B K 2.2µF/10V
CHD1AK30B225
D638
DIODE FR154
C884
CHIP CERAMIC CAP.(1608) B K 2.2µF/10V
CHD1AK30B225
D639
DIODE ZENER 1ZB43BB
NDWZ0001ZB43
C885
CHIP CERAMIC CAP.(1608) B K 2.2µF/10V
CHD1AK30B225
D641
SCHOTTKY BARRIER DIODE SB390
NDWZ000SB390
D642
SCHOTTKY BARRIER DIODE SB390
NDWZ000SB390
CN101
242 SERIES CONNECTOR 224202105W1
J322C05TG001
D643
DIODE FR104-B
NDLZ000FR104
CN201
FFC CONNECTOR 15P IMSA-9615S-15A-PP-A JC96J15ER007
D644
DIODE ZENER 6V2BSB-T26
NDTB6R2BST26
CN301
FFC CONNECTOR IMSA-9615S-29A-PP-A
JC96J29ER007
D645
SHUNT REGULATOR KIA431B-AT/P
NSZBA0TJY038
CN302
FFC CONNECTOR IMSA-9615S-29A-PP-A
JC96J29ER007
D646
DIODE SCHOTTKY SB360BH
NDWZ000SB360
CN602#
WIRE ASSEMBLY 3PIN 3PIN 145MM RED
BLACK
WX1A01F0-201
D647
SCHOTTKY BARRIER DIODE SB140
NDWZ000SB140
D648
WIRE COPPER 6111-06003-0120
XZ40C0SHG002
CN801
PH CONNECTOR TOP 2P B2B-PH-K-S
(LF)(SN)
J3PHC02JG029
D652
DIODE ZENER 5V6BSB-T26
NDTB5R6BST26
CN802
PH CONNECTOR TOP 2P B2B-PH-K-S
(LF)(SN)
J3PHC02JG029
D653
IC SHUNT REGULATOR KIA431-AT/PF5
NSZBB0TJY036
D654
WIRE COPPER 6111-06003-0120
XZ40C0SHG002
D655
RECTIFIER DIODE 1N4005
NDQZ001N4005
D657
DIODE ZENER 33BSB-T26
NDTB033BST26
D658
DIODE ZENER 3V3BSB-T26
NDTB3R3BST26
CONNECTORS
DIODES
D202
SWITCHING DIODE 1SS133(T-77)
20091113
QDTZ001SS133
14-3
A01F2EL
Ref. No.
D659
Description
Part No.
Ref. No.
Description
Part No.
DIODE ZENER 5V6BSA-T26
NDTA5R6BST26
Q640
TRANSISTOR 2SC2120-Y(TE2 F T)
QQSY2SC2120F
D660
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
Q641
TRANSISTOR 2SC2120-Y(TE2 F T)
QQSY2SC2120F
D661
DIODE FR154
NDLZ000FR154
Q642
TRANSISTOR KTC3198-Y-AT/P
NQSYKTC3198P
D662
DIODE FR154
NDLZ000FR154
Q643
TRANSISTOR 2SA950-O (TE2 F T)
QQS002SA950F
D664
DIODE ZENER 4V7BSB-T26
NDTB4R7BST26
Q771
TRANSISTOR KTC3198-Y-AT/P
NQSYKTC3198P
D665
WIRE COPPER 6111-06003-0120
XZ40C0SHG002
Q772
TRANSISTOR KTC3198-Y-AT/P
NQSYKTC3198P
D666
IC SHUNT REGULATOR KIA431-AT/P
NSZBA0TJY036
Q801
TRANSISTOR KTC3198-Y-AT/P
NQSYKTC3198P
D670
DIODE ZENER 10BSB-T26
NDTB010BST26
Q841
TRANSISTOR KTC3198-Y-AT/P
NQSYKTC3198P
D671
WIRE COPPER 6111-06003-0120
XZ40C0SHG002
Q871
TRANSISTOR KTC3198-Y-AT/P
NQSYKTC3198P
D676
WIRE COPPER 6111-06003-0120
XZ40C0SHG002
Q872
TRANSISTOR KTC3198-Y-AT/P
NQSYKTC3198P
D801
DIODE ZENER 20BSB-T26
NDTB020BST26
Q873
TRANSISTOR KTC3198-Y-AT/P
NQSYKTC3198P
D802
DIODE ZENER 20BSB-T26
NDTB020BST26
Q874
TRANSISTOR KTA1267-GR-AT/P
NQS1KTA1267P
D803
DIODE ZENER 20BSB-T26
NDTB020BST26
D804
DIODE ZENER 20BSB-T26
NDTB020BST26
RESISTORS
ICS
R201
CHIP RES. 1/10W J 100k Ω
RRXAJR5Z0104
R202
CHIP RES. 1/10W J 1k Ω
RRXAJR5Z0102
RCX4561T1001
IC201
IC TL3472CDR
NSZBA0TTY115
R204
RES CARBON FILM T 1/4W J 560 Ω
IC601#
PHOTO COUPLER LTV817MCF
NPECLTV817MF
R206
CHIP RES. 1/10W J 1k Ω
RRXAJR5Z0102
IC602#
IC SWITING FA5571N-D1-TE1/SOP-8
QSCA0T0FD003
R207
CHIP RES. 1/10W J 100k Ω
RRXAJR5Z0104
IC631
IC REGULATOR MM3123DPRE
QSCA0T0MM108
R208
CHIP RES. 1/10W J 1 Ω
RRXAJR5Z01R0
IC771
IC SWITCHING TC4052BF(ELNF)
QSZBA0TTS162
R209
CHIP RES.(1608) 1/10W 0 Ω
RRXAZR5Z0000
IC801
IC D-CLASS POWER AMPLIFER R2A15124FP/ QSCA0T0HT006
HSSOP/42
R210
RES CARBON FILM T 1/4W J 10 Ω
RCX4100T1001
R211
CHIP RES.(1608) 1/10W 0 Ω
RRXAZR5Z0000
R212
RES CARBON FILM T 1/4W J 10 Ω
RCX4100T1001
R213
CHIP RES. 1/10W J 100k Ω
RRXAJR5Z0104
IC871
IC OP AMP NJM4558M(TE1)-#ZZZB
QSZBA0TJR089
COILS
L301
WIRE COPPER 6111-06003-0120
XZ40C0SHG002
R214
CHIP RES.(1608) 1/10W 0 Ω
RRXAZR5Z0000
L302
CHIP INDUCTOR LK1608R22K-T
LLACKB3TUR22
R216
CHIP RES. 1/10W J 10k Ω
RRXAJR5Z0103
L303
CHIP INDUCTOR LK1608R22K-T
LLACKB3TUR22
R217
CHIP RES. 1/10W J 1.5k Ω
RRXAJR5Z0152
L601#
COIL LINE FILTER ST0908ET28V-016
LLEG0Z0Y2008
R218
CHIP RES. 1/10W J 10k Ω
RRXAJR5Z0103
L602#
COIL LINE FILTER ST0908ET28V-016
LLEG0Z0Y2008
R219
CHIP RES. 1/10W J 15k Ω
RRXAJR5Z0153
L801
RADIAL LEAD INDUCTORS 33µH
LLARKGQTU330
R220
CHIP RES. 1/10W J 1k Ω
RRXAJR5Z0102
L802
RADIAL LEAD INDUCTORS 33µH
LLARKGQTU330
R223
RES CARBON FILM T 1/4W J 3.3k Ω
RCX4332T1001
L803
RADIAL LEAD INDUCTORS 33µH
LLARKGQTU330
R224
RES CARBON FILM T 1/4W J 27k Ω
RCX4273T1001
L804
RADIAL LEAD INDUCTORS 33µH
LLARKGQTU330
R225
CHIP RES. 1/10W J 22k Ω
RRXAJR5Z0223
L871
WIRE COPPER 6111-06003-0120
XZ40C0SHG002
R226
CHIP RES. 1/10W J 22k Ω
RRXAJR5Z0223
R227
RES. CARBON FILM J 1/2W J 3.9 Ω
RCX23R9T1003
TRANSISTORS
Q201
TRANSISTOR KTA1267-GR-AT/P
NQS1KTA1267P
R228
RES CARBON FILM T 1/4W J 2.7k Ω
RCX4272T1001
Q202
TRANSISTOR KTC3198-Y-AT/P
NQSYKTC3198P
R229
RES CARBON FILM T 1/4W J 2.7k Ω
RCX4272T1001
Q203
TRANSISTOR KTC3198-Y-AT/P
NQSYKTC3198P
R231
CHIP RES. 1/10W J 1.5k Ω
RRXAJR5Z0152
Q204
TRANSISTOR KTA1267-GR-AT/P
NQS1KTA1267P
R232
CHIP RES. 1/10W F 11k Ω
RRXAFR5H1102
Q205
TRANSISTOR KTC3198-Y-AT/P
NQSYKTC3198P
R233
CHIP RES. 1/10W F 750 Ω
RRXAFR5H7500
Q207
TRANSISTOR KTA1267-GR-AT/P
NQS1KTA1267P
R234
CHIP RES. 1/10W F 2.2k Ω
RRXAFR5H2201
Q208
TRANSISTOR KTC3198-Y-AT/P
NQSYKTC3198P
R235
RES CARBON FILM T 1/4W J 330 Ω
RCX4331T1001
Q209
TRANSISTOR 2SC2120-Y(TE2 F T)
QQSY2SC2120F
R236
RES CARBON FILM T 1/4W J 10 Ω
RCX4100T1001
Q210
TRANSISTOR KTC3198-Y-AT/P
NQSYKTC3198P
R237
RES CARBON FILM T 1/4W J 8.2k Ω
RCX4822T1001
Q211
TRANSISTOR KTC3198-Y-AT/P
NQSYKTC3198P
R238
RES CARBON FILM T 1/4W J 1.5k Ω
RCX4152T1001
Q212
TRANSISTOR KTC3198-Y-AT/P
NQSYKTC3198P
R240
RES CARBON FILM T 1/4W J 47k Ω
RCX4473T1001
Q213
TRANSISTOR 2SA950-O (TE2 F T)
QQS002SA950F
R241
CHIP RES. 1/10W J 22k Ω
RRXAJR5Z0223
Q401
TRANSISTOR KTC3198-Y-AT/P
NQSYKTC3198P
R242
RES CARBON FILM T 1/4W J 12k Ω
RCX4123T1001
Q402
TRANSISTOR KTC3198-Y-AT/P
NQSYKTC3198P
R243
RES CARBON FILM T 1/4W J 220 Ω
RCX4221T1001
Q501
TRANSISTOR 2SC2120-Y(TE2 F T)
QQSY2SC2120F
R245
RES CARBON FILM T 1/4W J 8.2k Ω
RCX4822T1001
Q601#
FET MOS TK5A50D
QEWZTK5A50DQ
R247
RES. CARBON FILM J 1/2W J 4.7 Ω
RCX24R7T1003
Q602#
FET POWER MOS SMD KHB1D0N60D-RTF/
PMC
NF1ZKHB1D0N6
R248
CHIP RES. 1/10W J 10k Ω
RRXAJR5Z0103
Q603
TRANSISTOR KTC3198-Y-AT/P
NQSYKTC3198P
R250
METAL OXIDE FILM RES. 1W J 8.2 Ω
RN018R2ZU001
Q604
TRANSISTOR KTA1267-GR-AT/P
NQS1KTA1267P
R253
RES. CARBON FILM J 1/2W J 6.8 Ω
RCX26R8T1003
Q631
TRANSISTOR KTC3198-Y-AT/P
NQSYKTC3198P
R301
CHIP RES.(1608) 1/10W 0 Ω
RRXAZR5Z0000
Q634
TRANSISTOR KTC3199-GR-AT/P
NQS4KTC3199P
R302
CHIP RES.(1608) 1/10W 0 Ω
RRXAZR5Z0000
Q635
TRANSISTOR 2SC2120-Y(TE2 F T)
QQSY2SC2120F
R303
CHIP RES.(1608) 1/10W 0 Ω
RRXAZR5Z0000
Q636
TRANSISTOR 2SA950-O (TE2 F T)
QQS002SA950F
R304
CHIP RES. 1/10W J 47 Ω
RRXAJR5Z0470
Q637
NPN TRANSISTOR POWER 2SC4881F HFE
MAX320
QQWZ2SC4881F
R305
CHIP RES. 1/10W J 47 Ω
RRXAJR5Z0470
R311
CHIP RES.(1608) 1/10W 0 Ω
RRXAZR5Z0000
Q638
TRANSISTOR KTA1267-GR-AT/P
NQS1KTA1267P
R401
CHIP RES. 1/10W J 22k Ω
RRXAJR5Z0223
Q639
TRANSISTOR KTC3199-GR-AT/P
NQS4KTC3199P
R402
RES CARBON FILM T 1/4W J 22k Ω
RCX4223T1001
20091113
14-4
A01F2EL
Ref. No.
Description
R403
CHIP RES. 1/10W J 47k Ω
R404
R405
Part No.
Ref. No.
Description
RES CARBON FILM T 1/4W J 10 Ω
Part No.
RRXAJR5Z0473
R678
RCX4100T1001
CHIP RES. 1/10W J 22k Ω
RRXAJR5Z0223
R679
CHIP RES. 1/10W F 3.6k Ω
RRXAFR5H3601
RES CARBON FILM T 1/4W J 47k Ω
RCX4473T1001
R680
CHIP RES. 1/10W F 10k Ω
RRXAFR5H1002
R407
RES CARBON FILM T 1/4W J 22k Ω
RCX4223T1001
R682
RES CARBON FILM T 1/4W J 2.7 Ω
RCX42R7T1001
R408
CHIP RES. 1/10W J 10k Ω
RRXAJR5Z0103
R683
RES CARBON FILM T 1/4W J 2.7 Ω
RCX42R7T1001
R410
CHIP RES. 1/10W F 51.0 k Ω
RRXAFR5H5102
R685
RES CARBON FILM T 1/4W J 22 Ω
RCX4220T1001
R411
CHIP RES. 1/10W F 30k Ω
RRXAFR5H3002
R686
RES CARBON FILM T 1/4W J 1.0k Ω
RCX4102T1001
R412
CHIP RES. 1/10W J 10k Ω
RRXAJR5Z0103
R687
RES CARBON FILM T 1/4W J 10 Ω
RCX4100T1001
R501
RES CARBON FILM T 1/4W J 10 Ω
RCX4100T1001
R688
RES CARBON FILM T 1/4W J 10 Ω
RCX4100T1001
R601#
GLASS GLAZE RES. 1/2W J 2.7M Ω
RXX2JZLZ0275
R689
RES CARBON FILM T 1/4W J 1.2k Ω
RCX4122T1001
R603#
CEMENT RESISTOR 5W J 2.2 Ω H 10MM
RW052R2PAK10
R691
RES CARBON FILM T 1/4W J 1.8 Ω
RCX41R8T1001
R604
RES CHIP 3216 1/4W J 2.7M Ω
RRX4275HH034
R693
RES CARBON FILM T 1/4W J 1.5 Ω
RCX41R5T1001
RN012R7ZU001
R605#
CEMENT RESISTOR 5W J 2.2 Ω H 10MM
RW052R2PAK10
R696
METAL OXIDE FILM RES. 1W J 2.7 Ω
R606
RES CARBON FILM T 1/4W J 47k Ω
RCX4473T1001
R697
METAL OXIDE FILM RES. 1W J 2.7 Ω
RN012R7ZU001
R607
RES CHIP 3216 1/4W J 2.7M Ω
RRX4275HH034
R698
RES CARBON FILM T 1/4W J 2.2 Ω
RCX42R2T1001
R609
RES CARBON FILM T 1/4W J 180 Ω
RCX4181T1001
R723
CHIP RES. 1/10W J 15k Ω
RRXAJR5Z0153
R610
RES CARBON FILM T 1/4W J 10 Ω
RCX4100T1001
R724
CHIP RES. 1/10W J 15k Ω
RRXAJR5Z0153
R611
RES CARBON FILM T 1/4W J 4.7k Ω
RCX4472T1001
R725
CHIP RES. 1/10W J 39k Ω
RRXAJR5Z0393
R612
RES CARBON FILM T 1/4W J 68 Ω
RCX4680T1001
R726
CHIP RES. 1/10W J 39k Ω
RRXAJR5Z0393
R613#
METAL OXIDE RES. 2W J 0.36 Ω
RN02R36ZU001
R731
CHIP RES. 1/10W J 75 Ω
RRXAJR5Z0750
R617
RES CARBON FILM T 1/4W J 100k Ω
RCX4104T1001
R732
CHIP RES. 1/10W J 75 Ω
RRXAJR5Z0750
R618
WIRE COPPER 6111-06003-0120
XZ40C0SHG002
R733
CHIP RES. 1/10W J 75 Ω
RRXAJR5Z0750
R619
WIRE COPPER 6111-06003-0120
XZ40C0SHG002
R734
CHIP RES. 1/10W J 10 Ω
RRXAJR5Z0100
R622
RES CARBON FILM T 1/4W J 1.2k Ω
RCX4122T1001
R735
CHIP RES. 1/10W J 10 Ω
RRXAJR5Z0100
R623
RES CARBON FILM T 1/4W J 10k Ω
RCX4103T1001
R736
CHIP RES. 1/10W J 10 Ω
RRXAJR5Z0100
R624
RES CARBON FILM T 1/4W J 10k Ω
RCX4103T1001
R743
CHIP RES. 1/10W J 15k Ω
RRXAJR5Z0153
R626
RES CARBON FILM T 1/4W J 15k Ω
RCX4153T1001
R744
CHIP RES. 1/10W J 15k Ω
RRXAJR5Z0153
R635
RES. CARBON FILM J 1/2W J 3.9 Ω
RCX23R9T1003
R745
CHIP RES. 1/10W J 39k Ω
RRXAJR5Z0393
R636
RES. CARBON FILM J 1/2W J 3.9 Ω
RCX23R9T1003
R746
CHIP RES. 1/10W J 39k Ω
RRXAJR5Z0393
R637
RES CARBON FILM T 1/4W G 3.3k Ω
RCX4332T1002
R763
RES CARBON FILM T 1/4W J 10k Ω
RCX4103T1001
R638
WIRE COPPER 6111-06003-0120
XZ40C0SHG002
R771
WIRE COPPER 6111-06003-0120
XZ40C0SHG002
R639
RES CARBON FILM T 1/4W G 39k Ω
RCX4393T1002
R772
CHIP RES. 1/10W J 10k Ω
RRXAJR5Z0103
R641
RES CHIP.(1608) 1/10W D 1.1k Ω
RRXADR5H1101
R773
CHIP RES. 1/10W J 10k Ω
RRXAJR5Z0103
R642
RES CHIP.(1608) 1/10W D 10k Ω
RRXADR5H1002
R774
CHIP RES. 1/10W J 10k Ω
RRXAJR5Z0103
R643
RES CHIP.(1608) 1/10W D 10k Ω
RRXADR5H1002
R775
CHIP RES. 1/10W J 10k Ω
RRXAJR5Z0103
R644
CHIP RES. 1/10W F 1.5k Ω
RRXAFR5H1501
R776
CHIP RES. 1/10W J 100k Ω
RRXAJR5Z0104
R646
RES CARBON FILM T 1/4W J 180 Ω
RCX4181T1001
R777
CHIP RES. 1/10W J 100k Ω
RRXAJR5Z0104
R647
CHIP RES. 1/10W J 1k Ω
RRXAJR5Z0102
R778
CHIP RES. 1/10W J 100k Ω
RRXAJR5Z0104
R648
CHIP RES. 1/10W F 1.0k Ω
RRXAFR5H1001
R779
CHIP RES. 1/10W J 100k Ω
RRXAJR5Z0104
R649
RES CARBON FILM T 1/4W J 2.7k Ω
RCX4272T1001
R801
CHIP RES.(1608) 1/10W 0 Ω
RRXAZR5Z0000
R650
RES CARBON FILM T 1/4W J 2.7k Ω
RCX4272T1001
R802
CHIP RES. 1/10W J 22k Ω
RRXAJR5Z0223
R651
CHIP RES. 1/10W J 1 Ω
RRXAJR5Z01R0
R807
CHIP RES.(1608) 1/10W 0 Ω
RRXAZR5Z0000
R652
CHIP RES. 1/10W F 24k Ω
RRXAFR5H2402
R810
CHIP RES.(1608) 1/10W 0 Ω
RRXAZR5Z0000
R653
WIRE COPPER 6111-06003-0120
XZ40C0SHG002
R811
CHIP RES.(1608) 1/10W 0 Ω
RRXAZR5Z0000
R654
CHIP RES. 1/10W J 10k Ω
RRXAJR5Z0103
R812
CHIP RES.(1608) 1/10W 0 Ω
RRXAZR5Z0000
R655
RES CARBON FILM T 1/4W G 27k Ω
RCX4273T1002
R813
CHIP RES. 1/10W J 7.5k Ω
RRXAJR5Z0752
R657
RES CARBON FILM T 1/4W J 1.0 Ω
RCX41R0T1001
R814
CHIP RES. 1/10W J 47k Ω
RRXAJR5Z0473
R658
RES CARBON FILM T 1/4W J 10k Ω
RCX4103T1001
R815
CHIP RES. 1/10W J 7.5k Ω
RRXAJR5Z0752
R659
CHIP RES. 1/10W J 47k Ω
RRXAJR5Z0473
R816
CHIP RES. 1/10W J 47k Ω
RRXAJR5Z0473
R660
RES CARBON FILM T 1/4W J 820 Ω
RCX4821T1001
R817
CHIP RES. 1/10W J 100k Ω
RRXAJR5Z0104
R661
RES. CARBON FILM J 1/2W J 390 Ω
RCX2391T1003
R818
CHIP RES. 1/10W J 10k Ω
RRXAJR5Z0103
R662
RES CARBON FILM T 1/4W J 15 Ω
RCX4150T1001
R819
RES CARBON FILM T 1/4W J 22k Ω
RCX4223T1001
R663
RES CARBON FILM T 1/4W J 820 Ω
RCX4821T1001
R820
CHIP RES. 1/10W J 47k Ω
RRXAJR5Z0473
R664
RES CARBON FILM T 1/4W J 820 Ω
RCX4821T1001
R842
CHIP RES.(1608) 1/10W 0 Ω
RRXAZR5Z0000
R665
WIRE COPPER 6111-06003-0120
XZ40C0SHG002
R843
CHIP RES. 1/10W J 110 Ω
RRXAJR5Z0111
R667
WIRE COPPER 6111-06003-0120
XZ40C0SHG002
R844
CHIP RES. 1/10W J 220 Ω
RRXAJR5Z0221
R668
CHIP RES. 1/10W F 10k Ω
RRXAFR5H1002
R846
CHIP RES. 1/10W J 100 Ω
RRXAJR5Z0101
R672
WIRE COPPER 6111-06003-0120
XZ40C0SHG002
R847
CHIP RES. 1/10W J 4.7k Ω
RRXAJR5Z0472
R673
RES CARBON FILM T 1/4W J 22k Ω
RCX4223T1001
R848
CHIP RES. 1/10W J 4.7k Ω
RRXAJR5Z0472
R674
RES CARBON FILM T 1/4W J 1.0k Ω
RCX4102T1001
R871
CHIP RES. 1/10W J 560 Ω
RRXAJR5Z0561
R675
CHIP RES. 1/10W J 10k Ω
RRXAJR5Z0103
R872
CHIP RES. 1/10W J 560 Ω
RRXAJR5Z0561
R676
CHIP RES. 1/10W J 47k Ω
RRXAJR5Z0473
R873
CHIP RES. 1/10W J 100k Ω
RRXAJR5Z0104
R677
RES CARBON FILM T 1/4W J 270 Ω
RCX4271T1001
R874
CHIP RES. 1/10W J 100k Ω
RRXAJR5Z0104
20091113
14-5
A01F2EL
Ref. No.
Description
Part No.
JACK CBA(MPW-B)
R875
CHIP RES.(1608) 1/10W 0 Ω
RRXAZR5Z0000
R876
CHIP RES.(1608) 1/10W 0 Ω
RRXAZR5Z0000
R877
CHIP RES. 1/10W J 1k Ω
RRXAJR5Z0102
R878
RES CARBON FILM T 1/4W J 1.0k Ω
RCX4102T1001
R879
CHIP RES. 1/10W J 47k Ω
RRXAJR5Z0473
C754
RRXAZR5Z0000
R880
CHIP RES. 1/10W J 47k Ω
CHIP RES.(1608) 1/10W 0 Ω
RRXAJR5Z0473
C755
RRXAZR5Z0000
R881
CHIP RES. 1/10W J 100 Ω
CHIP RES.(1608) 1/10W 0 Ω
RRXAJR5Z0101
C756
RRXAZR5Z0000
R882
CHIP RES. 1/10W J 100 Ω
CHIP RES.(1608) 1/10W 0 Ω
RRXAJR5Z0101
C757
CHIP CERAMIC CAP.(1608) B K 2.2µF/10V
CHD1AK30B225
R883
CHIP RES. 1/10W J 100k Ω
RRXAJR5Z0104
C758
CHIP CERAMIC CAP.(1608) B K 2.2µF/10V
CHD1AK30B225
Ref. No.
Description
JACK CBA(MPW-B)
Consists of the following:
Part No.
----------
CAPACITORS
R884
CHIP RES. 1/10W J 100k Ω
RRXAJR5Z0104
R885
CHIP RES. 1/10W J 100k Ω
RRXAJR5Z0104
CHIP RES. 1/10W J 75 Ω
RRXAJR5Z0750
R886
CHIP RES. 1/10W J 100k Ω
R751
RRXAJR5Z0104
CHIP RES. 1/10W J 75 Ω
RRXAJR5Z0750
R887
CHIP RES. 1/10W J 22k Ω
R752
RRXAJR5Z0223
CHIP RES. 1/10W J 75 Ω
RRXAJR5Z0750
R888
CHIP RES. 1/10W J 1k Ω
R753
RRXAJR5Z0102
CHIP RES.(1608) 1/10W 0 Ω
RRXAZR5Z0000
R891
CHIP RES. 1/10W J 20k Ω
R756
RRXAJR5Z0203
CHIP RES.(1608) 1/10W 0 Ω
RRXAZR5Z0000
R892
CHIP RES. 1/10W J 20k Ω
R757
RRXAJR5Z0203
CHIP RES.(1608) 1/10W 0 Ω
RRXAZR5Z0000
R893
CHIP RES. 1/10W J 22k Ω
R758
RRXAJR5Z0223
CHIP RES. 1/10W J 15k Ω
RRXAJR5Z0153
R894
CHIP RES. 1/10W J 47k Ω
R759
RRXAJR5Z0473
R760
CHIP RES. 1/10W J 15k Ω
RRXAJR5Z0153
R761
CHIP RES. 1/10W J 39k Ω
RRXAJR5Z0393
R762
CHIP RES. 1/10W J 39k Ω
RRXAJR5Z0393
RESISTORS
MISCELLANEOUS
AC601#
AC CORD W/O A GND WIRE UL/CSA 1770 NO WAC0172LW022
BLACK
B11
POW HEAT SINK A7120UH
1EM423993
B43
HEAT SINK PMM A74F0UH
1EM424517A
BC301
WIRE COPPER 6111-06003-0120
XZ40C0SHG002
BC601
BEADS INDUCTOR FBR07HA121SB-00
LLBF00STU030
BC602
BEADS INDUCTOR FBR07HA121SB-00
LLBF00STU030
BC603
BEADS INDUCTOR FBR07HA121SB-00
LLBF00STU030
BC802
BEADS INDUCTOR FBR07HA121SB-00
LLBF00STU030
BC803
BEADS INDUCTOR FBR07HA121SB-00
LLBF00STU030
BC804
BEADS INDUCTOR FBR07HA121SB-00
LLBF00STU030
BC805
BEADS INDUCTOR FBR07HA121SB-00
BC841
BEADS INDUCTOR FBR07HA121SB-00
LLBF00STU030
CL701
WIRE ASSEMBLY 9P 9PIN/170MM
WX1A94F0-002
MISCELLANEOUS
JK751
JACK SW DIN PCB L DIN-435C(777D)
JYEL040YUQ03
JK752
JACK RCA PCB L RCA-101S(1)-03
JXRL010YUQ12
JK753
JACK RCA PCB L RCA-101S(1)-04
JXRL010YUQ13
JK754
JACK SW RCA PCB L RCA-102F(RD)
JYRL010YUQ05
INVERTER ASSEMBLY
Ref. No.
LLBF00STU030
Description
Part No.
INVERTER ASSEMBLY
Consists of the following:
A01F2M1V-001
INVERTER CBA
A01F2M1V-001-IV
--------------------------------------------------------------------- ---------------------------FUNCTION CBA
A01F2M1V-001-FNIRJN
IR SENSOR CBA
JUNCTION CBA
F601#
FUSE STC4A125V U/CT
PAGE20CW3402
FH601
FUSE HOLDER MSF-015 LF (B110)
XH01Z00LY002
FH602
FUSE HOLDER MSF-015 LF (B110)
XH01Z00LY002
JK721
JACK RCA PCB S WHITE 01/RCA-101H(WH)
JXRJ010YUQ02
JK722
JACK RCA PCB S RED 01/RCA-101H(RD)
JXRJ010YUQ01
JK731
JACK RCA PCB S GREEN 01/RCA-101H(GN)
JXRJ010YUQ03
JK732
JACK RCA PCB S BLUE 01/RCA-101H(BL)
JXRJ010YUQ04
JK733
JACK RCA PCB S RED 01/RCA-101H(RD)
JXRJ010YUQ01
JK741
JACK RCA PCB S WHITE 01/RCA-101H(WH)
JXRJ010YUQ02
JK742
JACK SW RCA PCB S RED RCA-102H(RD)
JYRJ010YUQ03
C1001
CHIP CERAMIC CAP.(1608) B K 0.1µF/50V
JK841
JACK RCA PCB S ORANGE 01/RCA-101H(OR) JXRJ010YUQ06
C1002
CHIP CERAMIC CAP.(1608) B K 0.01µF/50V
CHD1JK30B103
JK871
JACK RCA PCB S WHITE 01/RCA-101H(WH)
JXRJ010YUQ02
C1003
CHIP CERAMIC CAP.(1608) B K 0.1µF/50V
CHD1JK30B104
JK872
JACK RCA PCB S RED 01/RCA-101H(RD)
JXRJ010YUQ01
C1004
CHIP CERAMIC CAP.(1608) B K 0.1µF/50V
CHD1JK30B104
JS201
WIRE COPPER 6111-06003-0120
XZ40C0SHG002
C1005
CHIP CERAMIC CAP.(1608) B K 0.1µF/50V
CHD1JK30B104
JS202
WIRE COPPER 6111-06003-0120
XZ40C0SHG002
C1006
CHIP CERAMIC CAP.(1608) B K 0.1µF/50V
CHD1JK30B104
JS301
WIRE COPPER 6111-06003-0120
XZ40C0SHG002
C1007
CHIP CERAMIC CAP.(1608) B K 0.22µF/16V
CHD1CK30B224
JS630
WIRE COPPER 6111-06003-0120
XZ40C0SHG002
C1008
CHIP CERAMIC CAP.(1608) B K 0.1µF/50V
CHD1JK30B104
JS633
WIRE COPPER 6111-06003-0120
XZ40C0SHG002
C1009
ELECTROLYTIC CAP. 100µF/25V M
CE1EMASDL101
L3
SCREW B-TIGHT D3X8 BIND HEAD+
GBJB3080
C1011
CHIP CERAMIC CAP.(1608) B K 0.1µF/50V
CHD1JK30B104
SA601#
SURGE ABSORBER 470V+-10PER
NVQZ10D471KB
C1012
CA2A392DT018
T601#
TRANS POWER BCK-28-9910A
LTT2PC0XB058
POLYESTER FILM CAP. (PB FREE) 0.0039µF/
100V J
TM601
EYELET TYPE D-1
0VM406868
C1013
CHIP CERAMIC CAP.(1608) B K 0.1µF/50V
CHD1JK30B104
TM602
EYELET TYPE D-1
0VM406868
C1040
CHIP CERAMIC CAP.(1608) B K 0.47µF/10V
CHD1AK30B474
TU301
TUNER UNIT ATSC/NTSC/QAM UC130AF
UTNATS0SP004
C1052
ELECTROLYTIC CAP 100µF/100V
CE2AMZNDL101
20091113
INVERTER CBA
Ref. No.
Description
INVERTER CBA
Consists of the following:
Part No.
----------
CAPACITORS
14-6
CHD1JK30B104
C1053
ELECTROLYTIC CAP 100µF/100V
CE2AMZNDL101
C1056
ELECTROLYTIC CAP 100µF/100V
CE2AMZNDL101
C1061
CAP CERAMIC HV 15pF/6.3KV/SL/J
CCA1500MR001
C1062
CAP CERAMIC (AX) 1500pF/50V/B/K
CA1J152TU061
C1063
ELECTROLYTIC CAP. 10µF/50V M
CE1JMASDL100
C1064
CHIP CERAMIC CAP.(1608) B K 0.01µF/50V
CHD1JK30B103
A01F2EL
Ref. No.
C1065
Description
Part No.
Ref. No.
Description
Part No.
CAP CERAMIC HV 15pF/6.3KV/SL/J
CCA1500MR001
CN1100# CONNECTOR/JACK 1747386-1
JB17J02AP002
C1066
CAP CERAMIC (AX) 1500pF/50V/B/K
CA1J152TU061
CN1150# CONNECTOR/JACK 1747386-1
JB17J02AP002
C1067
ELECTROLYTIC CAP. 10µF/50V M
CE1JMASDL100
CN1200# CONNECTOR/JACK 1747386-1
JB17J02AP002
C1068
CHIP CERAMIC CAP.(1608) B K 0.01µF/50V
CHD1JK30B103
CN1900# CONNECTOR PRINT OSU 3 S B3P4-VH-L
J3VH030JG015
C1072
CHIP CERAMIC CAP.(1608) B K 0.01µF/50V
CHD1JK30B103
C1111
CAP CERAMIC HV 15pF/6.3KV/SL/J
CCA1500MR001
D1000
DIODE ZENER 15BSB-T26
NDTB015BST26
C1112
CAP CERAMIC (AX) 1500pF/50V/B/K
CA1J152TU061
D1001
WIRE COPPER 6111-06003-0120
XZ40C0SHG002
NDTB4R3BST26
DIODES
C1113
ELECTROLYTIC CAP. 10µF/50V M
CE1JMASDL100
D1002
DIODE ZENER 4V3BSB-T26
C1114
CHIP CERAMIC CAP.(1608) B K 0.01µF/50V
CHD1JK30B103
D1003
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
C1115
CAP CERAMIC HV 15pF/6.3KV/SL/J
CCA1500MR001
D1004
WIRE COPPER 6111-06003-0120
XZ40C0SHG002
C1116
CAP CERAMIC (AX) 1500pF/50V/B/K
CA1J152TU061
D1005
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
C1117
ELECTROLYTIC CAP. 10µF/50V M
CE1JMASDL100
D1006
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
C1118
CHIP CERAMIC CAP.(1608) B K 0.01µF/50V
CHD1JK30B103
D1040
DIODE ZENER 36BSB-T26
NDTB036BST26
C1122
CHIP CERAMIC CAP.(1608) B K 0.01µF/50V
CHD1JK30B103
D1060
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
C1161
CAP CERAMIC HV 15pF/6.3KV/SL/J
CCA1500MR001
D1061
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
C1162
CAP CERAMIC (AX) 1500pF/50V/B/K
CA1J152TU061
D1062
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
C1163
ELECTROLYTIC CAP. 10µF/50V M
CE1JMASDL100
D1063
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
C1164
CHIP CERAMIC CAP.(1608) B K 0.01µF/50V
CHD1JK30B103
D1064
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
C1165
CAP CERAMIC HV 15pF/6.3KV/SL/J
CCA1500MR001
D1065
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
C1166
CAP CERAMIC (AX) 1500pF/50V/B/K
CA1J152TU061
D1066
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
C1167
ELECTROLYTIC CAP. 10µF/50V M
CE1JMASDL100
D1067
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
C1168
CHIP CERAMIC CAP.(1608) B K 0.01µF/50V
CHD1JK30B103
D1068
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
C1172
CHIP CERAMIC CAP.(1608) B K 0.01µF/50V
CHD1JK30B103
D1069
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
C1211
CAP CERAMIC HV 15pF/6.3KV/SL/J
CCA1500MR001
D1070
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
C1212
CAP CERAMIC (AX) 1500pF/50V/B/K
CA1J152TU061
D1071
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
C1213
ELECTROLYTIC CAP. 10µF/50V M
CE1JMASDL100
D1072
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
C1214
CHIP CERAMIC CAP.(1608) B K 0.01µF/50V
CHD1JK30B103
D1073
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
C1215
CAP CERAMIC HV 15pF/6.3KV/SL/J
CCA1500MR001
D1074
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
C1216
CAP CERAMIC (AX) 1500pF/50V/B/K
CA1J152TU061
D1110
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
C1217
ELECTROLYTIC CAP. 10µF/50V M
CE1JMASDL100
D1111
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
C1218
CHIP CERAMIC CAP.(1608) B K 0.01µF/50V
CHD1JK30B103
D1112
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
C1222
CHIP CERAMIC CAP.(1608) B K 0.01µF/50V
CHD1JK30B103
D1113
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
C1500
CERAMIC CAP. 470pF/2KV
CA3D471PAN04
D1114
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
C1501
CHIP CERAMIC CAP.(1608) B K 5600pF/50V
CHD1JK30B562
D1115
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
C1502
CHIP CERAMIC CAP.(1608) B K 0.01µF/50V
CHD1JK30B103
D1116
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
C1550
CERAMIC CAP. 470pF/2KV
CA3D471PAN04
D1117
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
C1551
CHIP CERAMIC CAP.(1608) B K 5600pF/50V
CHD1JK30B562
D1118
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
C1552
CHIP CERAMIC CAP.(1608) B K 0.01µF/50V
CHD1JK30B103
D1119
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
C1600
CHIP CERAMIC CAP.(1608) B K 0.1µF/50V
CHD1JK30B104
D1120
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
C1620
CHIP CERAMIC CAP.(1608) CH J 1000pF/50V
CHD1JJ3CH102
D1121
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
C1702
CHIP CERAMIC CAP.(1608) F Z 0.22µF/50V
CHD1JZ30F224
D1122
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
C1703
CHIP CERAMIC CAP.(1608) F Z 0.22µF/50V
CHD1JZ30F224
D1123
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
C1800
ELECTROLYTIC CAP. 100µF/25V M
CE1EMASDL101
D1124
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
C1801
ELECTROLYTIC CAP. 22µF/35V M
CE1GMASDL220
D1160
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
C1802
CHIP CERAMIC CAP.(1608) B K 0.1µF/50V
CHD1JK30B104
D1161
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
C1905#
SAFTY CAP. 2200pF/250V KX
CA2E222MR101
D1162
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
C1910
CAP ELECTROLYTIC 270µF/200V
CEA271DYG005
D1163
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
C1930
CERAMIC CAP. 680pF/2KV
CA3D681PAN04
D1164
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
C1931#
POLYESTER FILM CAP. (PB FREE) 0.001µF/
100V J
CA2A102DT018
D1165
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
C1932
POLYESTER FILM CAP. (PB FREE) 0.027µF/
100V J
CA2A273DT018
D1166
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
D1167
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
C1933
POLYESTER FILM CAP. (PB FREE) 0.1µF/100V CA2A104DT018
J
D1168
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
D1169
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
POLYESTER FILM CAP. (PB FREE) 0.0022µF/
100V J
CA2A222DT018
D1170
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
C1981
CHIP CERAMIC CAP. F Z 0.01µF/50V
CHD1JZ30F103
D1171
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
C1982
ELECTROLYTIC CAP. 0.47µF/50V M
CE1JMASDLR47
D1172
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
C1990
CAP CERAMIC HV 820pF/1KV B K
CA3A821TE006
D1173
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
C1992#
ELECTROLYTIC CAP 470µF/100V
CE2AMZNDL471
D1174
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
D1210
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
D1211
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
D1212
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
D1213
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
C1970
CONNECTORS
CN1001
FFC CONNECTOR 15P IMSA-9615S-15A-PP-A JC96J15ER007
CN1003
FFC CONNECTOR IMSA-9615S-11A-PP-A
CN1050# CONNECTOR/JACK 1747386-1
20091113
JC96J11ER007
JB17J02AP002
14-7
A01F2EL
Ref. No.
Description
Part No.
Ref. No.
D1214
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
Q1803
D1215
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
D1216
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
D1217
SWITCHING DIODE 1SS133(T-77)
D1218
D1219
Description
Part No.
TRANSISTOR KTC3198-Y-AT/P
NQSYKTC3198P
Q1804
TRANSISTOR KTC3198-Y-AT/P
NQSYKTC3198P
Q1815
TRANSISTOR 2SA950-O (TE2 F T)
QQS002SA950F
QDTZ001SS133
Q1930#
MOS FET TK7A50D
QEWZTK7A50DQ
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
Q1931#
TRANSISTOR KTC3199-GR-AT/P
NQS4KTC3199P
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
Q1932#
TRANSISTOR 2SC2120-Y(TE2 F T)
QQSY2SC2120F
D1220
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
Q1970
NPN TRANSISTOR KTC3200-GR-AT/P
NQSGKTC3200P
D1221
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
Q1971
TRANSISTOR KTC3198-Y-AT/P
NQSYKTC3198P
D1222
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
Q1972
TRANSISTOR KTC3198-Y-AT/P
NQSYKTC3198P
D1223
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
D1224
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
R1001
CHIP RES. 1/10W F 22k Ω
D1500
DIODE ZENER 20BSB-T26
NDTB020BST26
R1002
CHIP RES. 1/10W F 1.0k Ω
RRXAFR5H1001
D1550
DIODE ZENER 20BSB-T26
NDTB020BST26
R1003
CHIP RES. 1/10W J 100k Ω
RRXAJR5Z0104
D1630
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
R1004
CHIP RES.(1608) 1/10W 0 Ω
RRXAZR5Z0000
D1700
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
R1005
RES CARBON FILM T 1/4W J 220k Ω
RCX4224T1001
D1701
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
R1006
RES CARBON FILM T 1/4W J 56k Ω
RCX4563T1001
D1702
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
R1007
CHIP RES. 1/10W J 10k Ω
RRXAJR5Z0103
D1703
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
R1008
CHIP RES. 1/10W J 2.2k Ω
RRXAJR5Z0222
D1801
DIODE ZENER 10BSB-T26
NDTB010BST26
R1009
CHIP RES. 1/10W J 82k Ω
RRXAJR5Z0823
D1802
WIRE COPPER 6111-06003-0120
XZ40C0SHG002
R1010
CHIP RES.(1608) 1/10W 0 Ω
RRXAZR5Z0000
D1930#
DIODE ZENER 27BSB-T26
NDTB027BST26
R1011
CHIP RES. 1/10W F 10k Ω
RRXAFR5H1002
D1931
DIODE ZENER 5V6BSB-T26
NDTB5R6BST26
R1012
CHIP RES. 1/10W F 12k Ω
RRXAFR5H1202
D1932
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
R1014
CHIP RES. 1/10W F 4.7k Ω
RRXAFR5H4701
D1933
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
R1015
CHIP RES. 1/10W F 7.50 k Ω
RRXAFR5H7501
D1934#
DIODE ZENER 39BSB-T26
NDTB039BST26
R1016
CHIP RES. 1/10W J 120k Ω
RRXAJR5Z0124
D1970
DIODE ZENER 5V6BSB-T26
NDTB5R6BST26
R1017
CHIP RES. 1/10W J 10k Ω
RRXAJR5Z0103
D1971
DIODE ZENER 30BSB-T26
NDTB030BST26
R1018
WIRE COPPER 6111-06003-0120
XZ40C0SHG002
D1972
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
R1019
RES CARBON FILM T 1/4W J 8.2k Ω
RCX4822T1001
D1973
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
R1021
RES CARBON FILM T 1/4W J 10k Ω
RCX4103T1001
D1990
DIODE FAST RECOVERY 31DF4-FC
QDWZ031DF4FC
R1022
CHIP RES. 1/10W F 2.2k Ω
RRXAFR5H2201
D1994
DIODE ZENER 1ZB100BB
NDWZ001ZB100
R1023
CHIP RES. 1/10W F 3.3k Ω
RRXAFR5H3301
R1024
CHIP RES. 1/10W F 100k Ω
RRXAFR5H1003
R1026
CHIP RES. 1/10W F 220 Ω
RRXAFR5H2200
R1028
CHIP RES. 1/10W F 36k Ω
RRXAFR5H3602
R1029
CHIP RES.(1608) 1/10W 0 Ω
RRXAZR5Z0000
R1030
CHIP RES. 1/10W J 22k Ω
RRXAJR5Z0223
R1031
CHIP RES. 1/10W J 15k Ω
RRXAJR5Z0153
R1032
RES CARBON FILM T 1/4W J 24k Ω
RCX4243T1001
RESISTORS
ICS
IC1000
IC PULSE-WIDTH-MODULATION CONT
TL494CDR
NSCA0T0TY006
IC1700
IC BA10324AF-E2
QSZBA0TRM032
IC1930#
PHOTO COUPLER LTV817MCF
NPECLTV817MF
IC1931#
PHOTO COUPLER LTV817MCF
NPECLTV817MF
TRANSISTORS
RRXAFR5H2202
Q1001
TRANSISTOR KTC3198-Y-AT/P
NQSYKTC3198P
R1033
CHIP RES. 1/10W J 10k Ω
RRXAJR5Z0103
Q1003
TRANSISTOR KTC3198-Y-AT/P
NQSYKTC3198P
R1034
CHIP RES. 1/10W J 10k Ω
RRXAJR5Z0103
Q1004
TRANSISTOR KTA1267-GR-AT/P
NQS1KTA1267P
R1035
RES CARBON FILM T 1/4W J 3.3k Ω
RCX4332T1001
Q1005
TRANSISTOR KTC3198-Y-AT/P
NQSYKTC3198P
R1036
RES CARBON FILM T 1/4W J 10k Ω
RCX4103T1001
Q1060
TRANSISTOR KTC3198-Y-AT/P
NQSYKTC3198P
R1040
METAL OXIDE FILM RES. 2W J 0.39 Ω
RN02R39ZU001
Q1061
TRANSISTOR KTC3198-Y-AT/P
NQSYKTC3198P
R1041
RES CARBON FILM T 1/4W J 33k Ω
RCX4333T1001
Q1110
TRANSISTOR KTC3198-Y-AT/P
NQSYKTC3198P
R1043
RES CARBON FILM T 1/4W J 12k Ω
RCX4123T1001
Q1111
TRANSISTOR KTC3198-Y-AT/P
NQSYKTC3198P
R1044
METAL OXIDE FILM RES. 2W J 0.39 Ω
RN02R39ZU001
Q1160
TRANSISTOR KTC3198-Y-AT/P
NQSYKTC3198P
R1060
CHIP RES. 1/10W J 100k Ω
RRXAJR5Z0104
Q1161
TRANSISTOR KTC3198-Y-AT/P
NQSYKTC3198P
R1061
CHIP RES. 1/10W J 20k Ω
RRXAJR5Z0203
Q1210
TRANSISTOR KTC3198-Y-AT/P
NQSYKTC3198P
R1062
CHIP RES. 1/10W J 390 Ω
RRXAJR5Z0391
Q1211
TRANSISTOR KTC3198-Y-AT/P
NQSYKTC3198P
R1063
CHIP RES. 1/10W F 18k Ω
RRXAFR5H1802
Q1500
FET MOS 2SK2417(FT)
QFWZSK2417FT
R1064
CHIP RES. 1/10W F 8.2k Ω
RRXAFR5H8201
Q1501
TRANSISTOR 2SC2120-Y(TE2 F T)
QQSY2SC2120F
R1065
RES CARBON FILM T 1/4W J 27k Ω
RCX4273T1001
Q1502
TRANSISTOR 2SA950-O (TE2 F T)
QQS002SA950F
R1066
CHIP RES. 1/10W J 100k Ω
RRXAJR5Z0104
Q1503
TRANSISTOR KTC3198-Y-AT/P
NQSYKTC3198P
R1067
CHIP RES. 1/10W J 20k Ω
RRXAJR5Z0203
Q1550
FET MOS 2SK2417(FT)
QFWZSK2417FT
R1068
CHIP RES. 1/10W J 390 Ω
RRXAJR5Z0391
Q1551
TRANSISTOR 2SC2120-Y(TE2 F T)
QQSY2SC2120F
R1069
CHIP RES. 1/10W F 18k Ω
RRXAFR5H1802
Q1552
TRANSISTOR 2SA950-O (TE2 F T)
QQS002SA950F
R1070
CHIP RES. 1/10W F 8.2k Ω
RRXAFR5H8201
Q1553
TRANSISTOR KTC3198-Y-AT/P
NQSYKTC3198P
R1071
RES CARBON FILM T 1/4W J 27k Ω
RCX4273T1001
Q1600
TRANSISTOR KTC3198-Y-AT/P
NQSYKTC3198P
R1072
CHIP RES. 1/10W J 1M Ω
RRXAJR5Z0105
Q1621
TRANSISTOR KTC3198-Y-AT/P
NQSYKTC3198P
R1080
CHIP RES. 1/10W F 22k Ω
RRXAFR5H2202
Q1800
TRANSISTOR KTC3198-Y-AT/P
NQSYKTC3198P
R1081
CHIP RES. 1/10W J 5.6k Ω
RRXAJR5Z0562
Q1801
TRANSISTOR KTA1267-GR-AT/P
NQS1KTA1267P
R1110
CHIP RES. 1/10W J 100k Ω
RRXAJR5Z0104
Q1802
TRANSISTOR KTC3198-Y-AT/P
NQSYKTC3198P
20091113
14-8
A01F2EL
Ref. No.
Description
R1111
CHIP RES. 1/10W J 20k Ω
R1112
R1113
Ref. No.
Part No.
Description
Part No.
RRXAJR5Z0203
R1803
RES CARBON FILM T 1/4W J 4.7k Ω
CHIP RES. 1/10W J 390 Ω
RRXAJR5Z0391
R1804
RES CARBON FILM T 1/4W J 1.2 Ω
RCX41R2T1001
CHIP RES. 1/10W F 18k Ω
RRXAFR5H1802
R1805
RES CARBON FILM T 1/4W J 1.0k Ω
RCX4102T1001
RCX4472T1001
R1114
CHIP RES. 1/10W F 8.2k Ω
RRXAFR5H8201
R1806
CHIP RES. 1/10W J 22k Ω
RRXAJR5Z0223
R1115
RES CARBON FILM T 1/4W J 27k Ω
RCX4273T1001
R1807
CHIP RES. 1/10W J 1k Ω
RRXAJR5Z0102
R1116
CHIP RES. 1/10W J 100k Ω
RRXAJR5Z0104
R1808
CHIP RES. 1/10W J 5.1k Ω
RRXAJR5Z0512
R1117
CHIP RES. 1/10W J 20k Ω
RRXAJR5Z0203
R1809
CHIP RES. 1/10W J 1.5k Ω
RRXAJR5Z0152
R1118
CHIP RES. 1/10W J 390 Ω
RRXAJR5Z0391
R1810
RES CARBON FILM T 1/4W J 4.7k Ω
RCX4472T1001
R1119
CHIP RES. 1/10W F 18k Ω
RRXAFR5H1802
R1811
RES CARBON FILM T 1/4W J 100k Ω
RCX4104T1001
R1120
CHIP RES. 1/10W F 8.2k Ω
RRXAFR5H8201
R1812
RES CARBON FILM T 1/4W J 12k Ω
RCX4123T1001
R1121
RES CARBON FILM T 1/4W J 27k Ω
RCX4273T1001
R1930
RES CARBON FILM T 1/4W J 47 Ω
RCX4470T1001
R1122
CHIP RES. 1/10W J 1M Ω
RRXAJR5Z0105
R1931
RES CARBON FILM T 1/4W J 100k Ω
RCX4104T1001
R1160
CHIP RES. 1/10W J 100k Ω
RRXAJR5Z0104
R1932
RES CARBON FILM T 1/4W J 82 Ω
RCX4820T1001
R1161
CHIP RES. 1/10W J 20k Ω
RRXAJR5Z0203
R1933
RES CARBON FILM T 1/4W J 82 Ω
RCX4820T1001
R1162
CHIP RES. 1/10W J 390 Ω
RRXAJR5Z0391
R1934
RES CARBON FILM T 1/4W J 180 Ω
RCX4181T1001
R1163
CHIP RES. 1/10W F 18k Ω
RRXAFR5H1802
R1935
RES CARBON FILM T 1/4W J 1.5k Ω
RCX4152T1001
R1164
CHIP RES. 1/10W F 8.2k Ω
RRXAFR5H8201
R1936
RES CARBON FILM T 1/4W J 180 Ω
RCX4181T1001
R1165
RES CARBON FILM T 1/4W J 27k Ω
RCX4273T1001
R1937#
METAL OXIDE FILM RES. 2W J 0.33 Ω
RN02R33ZU001
R1166
CHIP RES. 1/10W J 100k Ω
RRXAJR5Z0104
R1938
RES CARBON FILM T 1/4W J 82k Ω
RCX4823T1001
R1167
CHIP RES. 1/10W J 20k Ω
RRXAJR5Z0203
R1939
RES CARBON FILM T 1/4W J 2.2k Ω
RCX4222T1001
R1168
CHIP RES. 1/10W J 390 Ω
RRXAJR5Z0391
R1949
RES CARBON FILM T 1/4W J 150k Ω
RCX4154T1001
R1169
CHIP RES. 1/10W F 18k Ω
RRXAFR5H1802
R1967
RES CARBON FILM T 1/4W J 3.9k Ω
RCX4392T1001
R1170
CHIP RES. 1/10W F 8.2k Ω
RRXAFR5H8201
R1968
RES CARBON FILM T 1/4W J 3.9k Ω
RCX4392T1001
R1171
RES CARBON FILM T 1/4W J 27k Ω
RCX4273T1001
R1969
RES CARBON FILM T 1/4W J 3.9k Ω
RCX4392T1001
R1172
CHIP RES. 1/10W J 1M Ω
RRXAJR5Z0105
R1970
RES CARBON FILM T 1/4W J 270 Ω
RCX4271T1001
R1210
CHIP RES. 1/10W J 100k Ω
RRXAJR5Z0104
R1971
RES CARBON FILM T 1/4W J 3.9k Ω
RCX4392T1001
R1211
CHIP RES. 1/10W J 20k Ω
RRXAJR5Z0203
R1972
CHIP RES. 1/10W J 68k Ω
RRXAJR5Z0683
R1212
CHIP RES. 1/10W J 390 Ω
RRXAJR5Z0391
R1973
CHIP RES. 1/10W J 22k Ω
RRXAJR5Z0223
R1213
CHIP RES. 1/10W F 18k Ω
RRXAFR5H1802
R1975
CHIP RES. 1/10W F 30k Ω
RRXAFR5H3002
R1214
CHIP RES. 1/10W F 8.2k Ω
RRXAFR5H8201
R1976
CHIP RES. 1/10W F 30k Ω
RRXAFR5H3002
R1215
RES CARBON FILM T 1/4W J 27k Ω
RCX4273T1001
R1977
CHIP RES. 1/10W F 27k Ω
RRXAFR5H2702
R1216
CHIP RES. 1/10W J 100k Ω
RRXAJR5Z0104
R1979
CHIP RES. 1/10W F 6.8k Ω
RRXAFR5H6801
R1217
CHIP RES. 1/10W J 20k Ω
RRXAJR5Z0203
R1980
CHIP RES. 1/10W F 360 Ω
RRXAFR5H3600
R1218
CHIP RES. 1/10W J 390 Ω
RRXAJR5Z0391
R1981
CHIP RES.(1608) 1/10W 0 Ω
RRXAZR5Z0000
R1219
CHIP RES. 1/10W F 18k Ω
RRXAFR5H1802
R1982
CHIP RES. 1/10W J 2.7k Ω
RRXAJR5Z0272
R1220
CHIP RES. 1/10W F 8.2k Ω
RRXAFR5H8201
R1983
RES CARBON FILM T 1/4W J 33k Ω
RCX4333T1001
R1221
RES CARBON FILM T 1/4W J 27k Ω
RCX4273T1001
R1984
RES CARBON FILM T 1/4W J 15k Ω
RCX4153T1001
R1222
CHIP RES. 1/10W J 1M Ω
RRXAJR5Z0105
R1986
CHIP RES. 1/10W J 1k Ω
RRXAJR5Z0102
R1500
CHIP RES. 1/10W J 12k Ω
RRXAJR5Z0123
R1987
RES CARBON FILM T 1/4W J 820k Ω
RCX4824T1001
R1501
RES CARBON FILM T 1/4W J 10 Ω
RCX4100T1001
R1988
RES CARBON FILM T 1/4W J 1.0k Ω
RCX4102T1001
R1502
RES CARBON FILM T 1/4W J 150 Ω
RCX4151T1001
MISCELLANEOUS
R1503
RES CARBON FILM T 1/4W J 2.2k Ω
RCX4222T1001
B13
HEAT SINK PNA A94F0UH
R1504
RES CARBON FILM T 1/4W J 2.2k Ω
RCX4222T1001
B14
HEAT SINK PNB ASSEMBLY A94F0UH
1EM428123
R1505
CHIP RES. 1/10W J 1k Ω
RRXAJR5Z0102
BC1301
WIRE COPPER 6111-06003-0120
XZ40C0SHG002
R1506
CHIP RES. 1/10W J 1k Ω
RRXAJR5Z0102
BC1500
COIL BEADS CORE FBR07VA850TB-00
LLBF00ZTU020
R1550
RES CARBON FILM T 1/4W J 12k Ω
RCX4123T1001
BC1501
COIL BEADS CORE FBR07VA850TB-00
LLBF00ZTU020
R1551
RES CARBON FILM T 1/4W J 10 Ω
RCX4100T1001
BC1550
COIL BEADS CORE FBR07VA850TB-00
LLBF00ZTU020
R1552
RES CARBON FILM T 1/4W J 150 Ω
RCX4151T1001
BC1551
COIL BEADS CORE FBR07VA850TB-00
LLBF00ZTU020
R1553
RES CARBON FILM T 1/4W J 2.2k Ω
RCX4222T1001
BC1930
BEADS INDUCTOR FBR07HA121SB-00
LLBF00STU030
R1554
RES CARBON FILM T 1/4W J 2.2k Ω
RCX4222T1001
BC1931
BEADS INDUCTOR FBR07HA121SB-00
LLBF00STU030
R1555
CHIP RES. 1/10W J 1k Ω
RRXAJR5Z0102
L3
SCREW B-TIGHT D3X8 BIND HEAD+
GBJB3080
R1556
CHIP RES. 1/10W J 1k Ω
RRXAJR5Z0102
T1050#
TRANS INVERTER HVT-153
LTZ3PZ0XB009
R1600
CHIP RES. 1/10W J 18k Ω
RRXAJR5Z0183
T1100#
TRANS INVERTER HVT-153
LTZ3PZ0XB009
R1601
CHIP RES. 1/10W J 10k Ω
RRXAJR5Z0103
T1150#
TRANS INVERTER HVT-153
LTZ3PZ0XB009
R1620
CHIP RES. 1/10W J 100k Ω
RRXAJR5Z0104
T1200#
TRANS INVERTER HVT-153
LTZ3PZ0XB009
R1621
CHIP RES. 1/10W J 10k Ω
RRXAJR5Z0103
T1950#
TRANS POWER BCK-28-9919
LTT2PC0XB051
R1630
CHIP RES. 1/10W J 10k Ω
RRXAJR5Z0103
R1631
CHIP RES. 1/10W J 3.3k Ω
RRXAJR5Z0332
R1700
CHIP RES. 1/10W J 8.2k Ω
RRXAJR5Z0822
R1701
CHIP RES. 1/10W J 1k Ω
RRXAJR5Z0102
R1800
CHIP RES. 1/10W J 22k Ω
RRXAJR5Z0223
R1801
CHIP RES. 1/10W J 22k Ω
RRXAJR5Z0223
R1802
CHIP RES. 1/10W J 22k Ω
RRXAJR5Z0223
20091113
14-9
1EM428121
A01F2EL
FUNCTION CBA
Ref. No.
Description
FUNCTION CBA
Consists of the following:
Part No.
----------
CAPACITOR
C108
CAP CERAMIC (AX) 0.1µF/50V/F/Z
CA1J104TU062
RESISTORS
R108
RES CARBON FILM T 1/4W J 220 Ω
RCX4221T1001
R109
RES CARBON FILM T 1/4W G 10k Ω
RCX4103T1002
R111
RES CARBON FILM T 1/4W G 4.7k Ω
RCX4472T1002
R112
RES CARBON FILM T 1/4W G 2.7k Ω
RCX4272T1002
R113
RES CARBON FILM T 1/4W G 4.7k Ω
RCX4472T1002
R114
RES CARBON FILM T 1/4W G 8.2k Ω
RCX4822T1002
R115
RES CARBON FILM T 1/4W G 18k Ω
RCX4183T1002
SWITCHES
SW101B
TACT SWITCH SKQSAB
SST0101AL038
SW103B
TACT SWITCH SKQSAB
SST0101AL038
SW104B
TACT SWITCH SKQSAB
SST0101AL038
SW105B
TACT SWITCH SKQSAB
SST0101AL038
SW106B
TACT SWITCH SKQSAB
SST0101AL038
SW107B
TACT SWITCH SKQSAB
SST0101AL038
IR SENSOR CBA
Ref. No.
Description
IR SENSOR CBA
Consists of the following:
Part No.
----------
CAPACITORS
C101
ELECTROLYTIC CAP. 47µF/16V M H7
CE1CMAVSL470
C103
CHIP CERAMIC CAP. CH J 330pF/50V
CHD1JJ3CH331
C104
CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V
CHD1JZ30F104
DIODE
D101
LED (WHITE) SLR343WBC7T3XM
QPWM343WBC7T
RESISTORS
R101
RES CARBON FILM T 1/4W J 100 Ω
RCX4101T1001
R102
CHIP RES. 1/10W J 3.3k Ω
RRXAJR5Z0332
R103
CHIP RES. 1/10W J 9.1k Ω
RRXAJR5Z0912
R106
CHIP RES. 1/10W J 1k Ω
RRXAJR5Z0102
MISCELLANEOUS
CL102
WIRE ASSEMBLY 5PIN 5PIN/205MM
WX1A01F2-001
CL103
WIRE ASSEMBLY 3PIN 3PIN 180MM
WX1A01F2-002
RS101
SENSOR REMOTE RECEIVER KSM-712TH2E USESJRSKK044
JUNCTION CBA
Ref. No.
Description
JUNCTION CBA
Consists of the following:
Part No.
----------
CONNECTOR
CN151
242 SERIES CONNECTOR TUC-P05X-B1 WHT JCTUB05TG002
ST
20091113
14-10
A01F2EL
PARTS LIST [32PFL3505D/F7 (Serial No. : DS2A)]
Mechanical Parts
PRODUCT SAFETY NOTE: Products marked with a
# have special characteristics important to safety.
Before replacing any of these components, read
carefully the product safety notice in this service
manual. Don't degrade the safety of the product
through improper servicing.
NOTE: Parts that are not assigned part numbers
(---------) are not available.
Different parts from the original model
32PFL3505D/F7 (Serial No. : DS1A)
Ref. No.
Description
REAR ASSEMBLY A01FBUH
Part No.
1ESA24106
LCD1
LCD MODULE CMO 8BIT A GRADE
UJ32MXD
S1
CARTON A01F2UH
1EM431817
20100507
14-11
A01FBCA
Electrical Parts
PRODUCT SAFETY NOTE: Products marked with a
# have special characteristics important to safety.
Before replacing any of these components, read
carefully the product safety notice in this service
manual. Don't degrade the safety of the product
through improper servicing.
NOTES:
1. Parts that are not assigned part numbers (---------)
are not available.
2. Tolerance of Capacitors and Resistors are noted
with the following symbols.
C.....±0.25%
D.....±0.5%
F.....±1%
G.....±2%
J......±5%
K.....±10%
M.....±20%
N.....±30%
Z.....+80/-20%
Different parts from the original model
32PFL3505D/F7 (Serial No. : DS1A)
There are no different parts from the original
model 32PFL3505D/F7 (Serial No. : DS1A).
Refer to the parts list for the original model
32PFL3505D/F7 (Serial No. : DS1A).
20100507
14-12
A01FBEL
PARTS LIST [32PFL3505D/F7 (Serial No. : DS4A)]
Mechanical Parts
PRODUCT SAFETY NOTE: Products marked with a
# have special characteristics important to safety.
Before replacing any of these components, read
carefully the product safety notice in this service
manual. Don't degrade the safety of the product
through improper servicing.
NOTE: Parts that are not assigned part numbers
(---------) are not available.
Different parts from the original model
32PFL3505D/F7 (Serial No. : DS1A)
Ref. No.
Description
Part No.
REAR ASSEMBLY A01FDUH
1ESA24419
CL201
WIRE ASSEMBLY 15PIN FFC 15PIN 140MM
WX1A01F4-102
CL1003
WIRE ASSEMBLY 11PIN FFC 11PIN 129MM
WX1A01F4-101
LCD1
LCD MODULE IPS ALPHA 8BIT
UJ32AXB
S1
CARTON A01F2UH
1EM431817
20100712
14-13
A01FDCA
Electrical Parts
PRODUCT SAFETY NOTE: Products marked with a
# have special characteristics important to safety.
Before replacing any of these components, read
carefully the product safety notice in this service
manual. Don't degrade the safety of the product
through improper servicing.
NOTES:
1. Parts that are not assigned part numbers (---------)
are not available.
2. Tolerance of Capacitors and Resistors are noted
with the following symbols.
C.....±0.25%
D.....±0.5%
F.....±1%
G.....±2%
J......±5%
K.....±10%
M.....±20%
N.....±30%
Z.....+80/-20%
Different parts from the original model
32PFL3505D/F7 (Serial No. : DS1A)
Ref. No.
Description
Part No.
DIGITAL MAIN CBA UNIT
A01FDMMA-003
MPW CBA
A01FDMPWS001
POWER SUPPLY CBA(MPW-A)
----------
D205
DIODE ZENER 33BSA-T26
NDTA033BST26
D210
DIODE ZENER 5V1BSB-T26
NDTB5R1BST26
D406
DIODE ZENER 27BSB-T26
NDTB027BST26
D621
DIODE ZENER 1ZB200-YBB
NDWZ01ZB200Y
D644
DIODE ZENER 7V5BSB-T26
NDTB7R5BST26
R204
RES CARBON FILM T 1/4W J 1.0k Ω
RCX4102T1001
R227
RES. CARBON FILM J 1/2W J 5.6 Ω
RCX25R6T1003
R228
RES CARBON FILM T 1/4W J 3.3k Ω
RCX4332T1001
R229
RES CARBON FILM T 1/4W J 3.3k Ω
RCX4332T1001
R232
CHIP RES. 1/10W F 9.1k Ω
RRXAFR5H9101
R233
CHIP RES.(1608) 1/10W 0 Ω
RRXAZR5Z0000
R235
RES CARBON FILM T 1/4W J 68 Ω
RCX4680T1001
R236
WIRE COPPER 6111-06003-0120
XZ40C0SHG002
R238
RES CARBON FILM T 1/4W J 150 Ω
RCX4151T1001
R243
RES CARBON FILM T 1/4W J 120 Ω
RCX4121T1001
R247
RES. CARBON FILM J 1/2W J 5.6 Ω
RCX25R6T1003
R253
RES. CARBON FILM J 1/2W J 5.6 Ω
RCX25R6T1003
R410
CHIP RES. 1/10W F 39k Ω
RRXAFR5H3902
R411
CHIP RES. 1/10W F 47.0 k Ω
RRXAFR5H4702
R412
CHIP RES. 1/10W J 3.3k Ω
RRXAJR5Z0332
R501
RES CARBON FILM T 1/4W J 6.8 Ω
RCX46R8T1001
R686
RES CARBON FILM T 1/4W J 680 Ω
RCX4681T1001
R689
RES CARBON FILM T 1/4W J 560 Ω
RCX4561T1001
T601#
TRANS POWER BCK-28-9885
LTT2PC0XB067
20100712
14-14
A01FDEL
PARTS LIST [32PFL3505D/F7 (Serial No. : DS8A)]
Mechanical Parts
PRODUCT SAFETY NOTE: Products marked with a
# have special characteristics important to safety.
Before replacing any of these components, read
carefully the product safety notice in this service
manual. Don't degrade the safety of the product
through improper servicing.
NOTE: Parts that are not assigned part numbers
(---------) are not available.
Different parts from the original model
32PFL3505D/F7 (Serial No. : DS1A)
Ref. No.
Description
REAR ASSEMBLY A01FDUH
Part No.
1ESA24419
B44
THERMAL SHEET TMS-14-20 12X12
XK10000X4011
CL201
WIRE ASSEMBLY 15PIN FFC 15PIN 140MM
WX1A01F4-102
CL1003
WIRE ASSEMBLY 11PIN FFC 11PIN 129MM
WX1A01F4-101
LCD1
LCD MODULE IPS ALPHA 8BIT
UJ32AXB
S1
CARTON A01F2UH
1EM431817
20101004
14-15
A01FD(DS8A)CA
Electrical Parts
PRODUCT SAFETY NOTE: Products marked with a
# have special characteristics important to safety.
Before replacing any of these components, read
carefully the product safety notice in this service
manual. Don't degrade the safety of the product
through improper servicing.
Ref. No.
D1971
CL102
NOTES:
1. Parts that are not assigned part numbers (---------)
are not available.
Description
Part No.
INVERTER CBA
----------
DIODE ZENER 33BSB-T26
NDTB033BST26
IR SENSOR CBA
----------
WIRE ASSEMBLY 5PIN 5PIN/205MM
WX1A01F2-021
JUNCTION CBA
(In this model, the JUNCTION CBA is not
used.)
CN151
Not used
2. Tolerance of Capacitors and Resistors are noted
with the following symbols.
C.....±0.25%
D.....±0.5%
F.....±1%
G.....±2%
J......±5%
K.....±10%
M.....±20%
N.....±30%
Z.....+80/-20%
Different parts from the original model
32PFL3505D/F7 (Serial No. : DS1A)
Ref. No.
Description
Part No.
DIGITAL MAIN CBA UNIT
A01FDMMA-003
MPW CBA
A01FDMPWS002
POWER SUPPLY CBA(MPW-A)
----------
CN101
CONNECTOR PRINT OSU B5B-PH-K-S
(LF)(SN)
J3PHC05JG029
D205
DIODE ZENER 33BSA-T26
NDTA033BST26
D210
DIODE ZENER 5V1BSB-T26
NDTB5R1BST26
D406
DIODE ZENER 27BSB-T26
NDTB027BST26
D621
DIODE ZENER 1ZB200-YBB
NDWZ01ZB200Y
D644
DIODE ZENER 7V5BSB-T26
NDTB7R5BST26
R204
RES CARBON FILM T 1/4W J 1.0k Ω
RCX4102T1001
R227
RES. CARBON FILM J 1/2W J 5.6 Ω
RCX25R6T1003
R228
RES CARBON FILM T 1/4W J 3.3k Ω
RCX4332T1001
R229
RES CARBON FILM T 1/4W J 3.3k Ω
RCX4332T1001
R232
CHIP RES. 1/10W F 9.1k Ω
RRXAFR5H9101
R233
CHIP RES.(1608) 1/10W 0 Ω
RRXAZR5Z0000
R235
RES CARBON FILM T 1/4W J 68 Ω
RCX4680T1001
R236
WIRE COPPER 6111-06003-0120
XZ40C0SHG002
R238
RES CARBON FILM T 1/4W J 150 Ω
RCX4151T1001
R243
RES CARBON FILM T 1/4W J 120 Ω
RCX4121T1001
R247
RES. CARBON FILM J 1/2W J 5.6 Ω
RCX25R6T1003
R253
RES. CARBON FILM J 1/2W J 5.6 Ω
RCX25R6T1003
R410
CHIP RES. 1/10W F 39k Ω
RRXAFR5H3902
R411
CHIP RES. 1/10W F 47.0 k Ω
RRXAFR5H4702
R412
CHIP RES. 1/10W J 3.3k Ω
RRXAJR5Z0332
R501
RES CARBON FILM T 1/4W J 6.8 Ω
RCX46R8T1001
R686
RES CARBON FILM T 1/4W J 680 Ω
RCX4681T1001
R689
RES CARBON FILM T 1/4W J 560 Ω
RCX4561T1001
T601#
TRANS POWER BCK-28-9885
LTT2PC0XB067
INVERTER ASSEMBLY
Consists of the following
A01F2M1V-002
INVERTER CBA
A01F2M1V-002-IV
---------------------------------------------------------------- --------------------------------FUNCTION CBA
A01F2M1V-002-FNIR
IR SENSOR CBA
20101004
14-16
A01FD(DS8A)EL
PARTS LIST [32PFL3505D/F7 (Serial No. : DS9A)]
Mechanical Parts
PRODUCT SAFETY NOTE: Products marked with a
# have special characteristics important to safety.
Before replacing any of these components, read
carefully the product safety notice in this service
manual. Don't degrade the safety of the product
through improper servicing.
NOTE: Parts that are not assigned part numbers
(---------) are not available.
Different parts from the original model
32PFL3505D/F7 (Serial No. : DS1A)
Ref. No.
Description
REAR ASSEMBLY A0RF2UH
Part No.
1ESA26470
B44
THERMAL SHEET TMS-14-20 12X12
XK10000X4011
CL201
WIRE ASSEMBLY 15PIN FFC 15PIN 140MM
WX1A01F4-102
CL1003
WIRE ASSEMBLY 11PIN FFC 11PIN 129MM
WX1A01F4-101
LCD1
LCD MODULE IPS ALPHA 8BIT
UJ32AXD
S1
CARTON A01F2UH
1EM431817
20101126
14-17
A0RF2CA
Electrical Parts
PRODUCT SAFETY NOTE: Products marked with a
# have special characteristics important to safety.
Before replacing any of these components, read
carefully the product safety notice in this service
manual. Don't degrade the safety of the product
through improper servicing.
Ref. No.
D1971
CL102
Description
Part No.
INVERTER CBA
----------
DIODE ZENER 33BSB-T26
NDTB033BST26
IR SENSOR CBA
----------
WIRE ASSEMBLY 5PIN 5PIN/205MM
WX1A01F2-021
NOTES:
1. Parts that are not assigned part numbers (---------)
are not available.
CN151
2. Tolerance of Capacitors and Resistors are noted
with the following symbols.
C.....±0.25%
D.....±0.5%
F.....±1%
G.....±2%
J......±5%
K.....±10%
M.....±20%
N.....±30%
Z.....+80/-20%
JUNCTION CBA
(In this model, the JUNCTION CBA is not
used.)
Not used
Different parts from the original model
32PFL3505D/F7 (Serial No. : DS1A)
Ref. No.
Description
Part No.
DIGITAL MAIN CBA UNIT
A01FDMMA-003
MPW CBA
A01FDMPWS002
POWER SUPPLY CBA(MPW-A)
----------
CN101
CONNECTOR PRINT OSU B5B-PH-K-S
(LF)(SN)
J3PHC05JG029
D205
DIODE ZENER 33BSA-T26
NDTA033BST26
D210
DIODE ZENER 5V1BSB-T26
NDTB5R1BST26
D406
DIODE ZENER 27BSB-T26
NDTB027BST26
D621
DIODE ZENER 1ZB200-YBB
NDWZ01ZB200Y
D644
DIODE ZENER 7V5BSB-T26
NDTB7R5BST26
D653
IC SHUNT REGULATOR KIA431-AT/PF5
NSZBB0TJY036
R204
RES CARBON FILM T 1/4W J 1.0k Ω
RCX4102T1001
R227
RES. CARBON FILM J 1/2W J 5.6 Ω
RCX25R6T1003
R228
RES CARBON FILM T 1/4W J 3.3k Ω
RCX4332T1001
R229
RES CARBON FILM T 1/4W J 3.3k Ω
RCX4332T1001
R232
CHIP RES. 1/10W F 9.1k Ω
RRXAFR5H9101
R233
CHIP RES.(1608) 1/10W 0 Ω
RRXAZR5Z0000
R235
RES CARBON FILM T 1/4W J 68 Ω
RCX4680T1001
R236
WIRE COPPER 6111-06003-0120
XZ40C0SHG002
R238
RES CARBON FILM T 1/4W J 150 Ω
RCX4151T1001
R243
RES CARBON FILM T 1/4W J 120 Ω
RCX4121T1001
R247
RES. CARBON FILM J 1/2W J 5.6 Ω
RCX25R6T1003
R253
RES. CARBON FILM J 1/2W J 5.6 Ω
RCX25R6T1003
R410
CHIP RES. 1/10W F 39k Ω
RRXAFR5H3902
R411
CHIP RES. 1/10W F 47.0 k Ω
RRXAFR5H4702
R412
CHIP RES. 1/10W J 3.3k Ω
RRXAJR5Z0332
R501
RES CARBON FILM T 1/4W J 6.8 Ω
RCX46R8T1001
R686
RES CARBON FILM T 1/4W J 680 Ω
RCX4681T1001
R689
RES CARBON FILM T 1/4W J 560 Ω
RCX4561T1001
T601#
TRANS POWER BCK-28-9885
LTT2PC0XB067
INVERTER ASSEMBLY
Consists of the following
A01F2M1V-002
INVERTER CBA
A01F2M1V-002-IV
---------------------------------------------------------------- --------------------------------FUNCTION CBA
A01F2M1V-002-FNIR
IR SENSOR CBA
20101126
14-18
A0RF2EL
PARTS LIST [32PFL3505D/F7 (Serial No. : YA1A)]
Mechanical Parts
PRODUCT SAFETY NOTE: Products marked with a
# have special characteristics important to safety.
Before replacing any of these components, read
carefully the product safety notice in this service
manual. Don't degrade the safety of the product
through improper servicing.
NOTE: Parts that are not assigned part numbers
(---------) are not available.
Different parts from the original model
32PFL3505D/F7 (Serial No. : DS1A)
Ref. No.
Description
REAR CABINET ASSEMBLY A01F9MZ
Part No.
1ESA24233
STAND ASSEMBLY A91FQUZ
1ESA22609
A10#
RATING LABEL A01F9MF
----------
A17
ENERGY STAR LABEL A91H5UF
----------
A18
Not used
L9
STAND SCREW KIT A01F9MF
1ESA24389
S1
CARTON A01F9MF
1EM431697
S2
STYROFOAM TOP A01F9MF
1EM025685
S3
STYROFOAM BOTTOM A01F9MF
1EM025686
S5
SERIAL NO.LABEL A01Q0UF
----------
X1
OWNERS MANUAL BAG A91H5UF
1EM429581
X2#
OWNERS MANUAL A01F9MF
1EMN26239
X6
QUICK START GUIDE A01F9MF
1EMN26242
X8
CHILD SAFETY SHEET A91H5UF
1EMN25001
X9
CONNECTION GUIDE A91FQUF
1EM327017
X10
REGISTRATION CARD A01P5UF
1EMN26042A
X12
WALL MOUNT INSTRUCTION A01F9MF
1EMN26240
20100423
14-19
A01F9CA
Electrical Parts
PRODUCT SAFETY NOTE: Products marked with a
# have special characteristics important to safety.
Before replacing any of these components, read
carefully the product safety notice in this service
manual. Don't degrade the safety of the product
through improper servicing.
NOTES:
1. Parts that are not assigned part numbers (---------)
are not available.
2. Tolerance of Capacitors and Resistors are noted
with the following symbols.
C.....±0.25%
D.....±0.5%
F.....±1%
G.....±2%
J......±5%
K.....±10%
M.....±20%
N.....±30%
Z.....+80/-20%
Different parts from the original model
32PFL3505D/F7 (Serial No. : DS1A)
Ref. No.
Description
Part No.
INVERTER ASSEMBLY
Consists of the following
A01F9M1V-001
INVERTER CBA
A01F9M1V-001-IV
------------------------------------------------------------- -----------------------------------A01F9M1V-001-FNIRJN
FUNCTION CBA
IR SENSOR CBA
JUNCTION CBA
20100423
14-20
A01F9EL
PARTS LIST [32PFL3505D/F7 (Serial No. : YA2A)]
Mechanical Parts
PRODUCT SAFETY NOTE: Products marked with a
# have special characteristics important to safety.
Before replacing any of these components, read
carefully the product safety notice in this service
manual. Don't degrade the safety of the product
through improper servicing.
NOTE: Parts that are not assigned part numbers
(---------) are not available.
Different parts from the original model
32PFL3505D/F7 (Serial No. : DS1A)
Ref. No.
Description
STAND ASSEMBLY A91FQUZ
Part No.
1ESA22609
REAR CABINET ASSEMBLY A01F9MZ
1ESA24233
A10#
RATING LABEL A01FUMF
----------
A17
ENERGY STAR LABEL A91H5UF
----------
A18
Not used
B44
THERMAL SHEET TMS-14-20 12X12
XK10000X4011
CL201
WIRE ASSEMBLY 15PIN FFC 15PIN 140MM
WX1A01F4-102
CL1003
WIRE ASSEMBLY 11PIN FFC 11PIN 129MM
WX1A01F4-101
L9
STAND SCREW KIT A01F9MF
1ESA24389
LCD1
LCD MODULE IPS ALPHA 8BIT
UJ32AXB
S1
CARTON A01F9MF
1EM432839
S2
STYROFOAM TOP A01F9MF
1EM025685
S3
STYROFOAM BOTTOM A01F9MF
1EM025686
S5
SERIAL NO.LABEL A01Q0UF
----------
X1
OWNERS MANUAL BAG A91H5UF
1EM429581
X2#
OWNERS MANUAL A01F9MF
1EMN26239
X6
QUICK START GUIDE A01F9MF
1EMN26242
X8
CHILD SAFETY SHEET A91H5UF
1EMN25001
X9
CONNECTION GUIDE A91FQUF
1EM327017
X10
REGISTRATION CARD A01P5UF
1EMN26042A
X12
WALL MOUNT INSTRUCTION A01F9MF
1EMN26240
20101105
14-21
A01FUCA
Electrical Parts
PRODUCT SAFETY NOTE: Products marked with a
# have special characteristics important to safety.
Before replacing any of these components, read
carefully the product safety notice in this service
manual. Don't degrade the safety of the product
through improper servicing.
Ref. No.
D1971
CL102
NOTES:
1. Parts that are not assigned part numbers (---------)
are not available.
Description
Part No.
INVERTER CBA
----------
DIODE ZENER 33BSB-T26
NDTB033BST26
IR SENSOR CBA
----------
WIRE ASSEMBLY 5PIN 5PIN/205MM
WX1A01F2-021
JUNCTION CBA
(In this model, the JUNCTION CBA is not
used.)
CN151
Not used
2. Tolerance of Capacitors and Resistors are noted
with the following symbols.
C.....±0.25%
D.....±0.5%
F.....±1%
G.....±2%
J......±5%
K.....±10%
M.....±20%
N.....±30%
Z.....+80/-20%
Different parts from the original model
32PFL3505D/F7 (Serial No. : DS1A)
Ref. No.
Description
Part No.
DIGITAL MAIN CBA UNIT
A01FDMMA-003
MPW CBA
A01FDMPWS002
POWER SUPPLY CBA(MPW-A)
----------
CN101
CONNECTOR PRINT OSU B5B-PH-K-S
(LF)(SN)
J3PHC05JG029
D205
DIODE ZENER 33BSA-T26
NDTA033BST26
D210
DIODE ZENER 5V1BSB-T26
NDTB5R1BST26
D406
DIODE ZENER 27BSB-T26
NDTB027BST26
D621
DIODE ZENER 1ZB200-YBB
NDWZ01ZB200Y
D644
DIODE ZENER 7V5BSB-T26
NDTB7R5BST26
R204
RES CARBON FILM T 1/4W J 1.0k Ω
RCX4102T1001
R227
RES. CARBON FILM J 1/2W J 5.6 Ω
RCX25R6T1003
R228
RES CARBON FILM T 1/4W J 3.3k Ω
RCX4332T1001
R229
RES CARBON FILM T 1/4W J 3.3k Ω
RCX4332T1001
R232
CHIP RES. 1/10W F 9.1k Ω
RRXAFR5H9101
R233
CHIP RES.(1608) 1/10W 0 Ω
RRXAZR5Z0000
R235
RES CARBON FILM T 1/4W J 68 Ω
RCX4680T1001
R236
WIRE COPPER 6111-06003-0120
XZ40C0SHG002
R238
RES CARBON FILM T 1/4W J 150 Ω
RCX4151T1001
R243
RES CARBON FILM T 1/4W J 120 Ω
RCX4121T1001
R247
RES. CARBON FILM J 1/2W J 5.6 Ω
RCX25R6T1003
R253
RES. CARBON FILM J 1/2W J 5.6 Ω
RCX25R6T1003
R410
CHIP RES. 1/10W F 39k Ω
RRXAFR5H3902
R411
CHIP RES. 1/10W F 47.0 k Ω
RRXAFR5H4702
R412
CHIP RES. 1/10W J 3.3k Ω
RRXAJR5Z0332
R501
RES CARBON FILM T 1/4W J 6.8 Ω
RCX46R8T1001
R686
RES CARBON FILM T 1/4W J 680 Ω
RCX4681T1001
R689
RES CARBON FILM T 1/4W J 560 Ω
RCX4561T1001
T601#
TRANS POWER BCK-28-9885
LTT2PC0XB067
INVERTER ASSEMBLY
Consists of the following
A01FUM1V-002
INVERTER CBA
A01FUM1V-002-IV
---------------------------------------------------------------- --------------------------------FUNCTION CBA
A01FUM1V-002-FNIR
IR SENSOR CBA
20101105
14-22
A01FUEL
PARTS LIST [32PFL3515D/F7 (Serial No. : YA1A)]
Mechanical Parts
PRODUCT SAFETY NOTE: Products marked with a
# have special characteristics important to safety.
Before replacing any of these components, read
carefully the product safety notice in this service
manual. Don't degrade the safety of the product
through improper servicing.
NOTE: Parts that are not assigned part numbers
(---------) are not available.
Different parts from the original model
32PFL3505D/F7 (Serial No. : DS1A)
Ref. No.
Description
REAR CABINET ASSEMBLY A01F9MZ
Part No.
1ESA24233
STAND ASSEMBLY A91FQUZ
1ESA22609
A10#
RATING LABEL A01FEMF
----------
A17
ENERGY STAR LABEL A91H5UF
----------
A18
Not used
L9
STAND SCREW KIT A01F9MF
1ESA24389
S1
CARTON A01FEMF
1EM431859
S2
STYROFOAM TOP A01F9MF
1EM025685
S3
STYROFOAM BOTTOM A01F9MF
1EM025686
S5
SERIAL NO.LABEL A01Q0UF
----------
X1
OWNERS MANUAL BAG A91H5UF
1EM429581
X2#
OWNERS MANUAL A01F9MF
1EMN26239
X6
QUICK START GUIDE A01F9MF
1EMN26242
X8
CHILD SAFETY SHEET A91H5UF
1EMN25001
X9
CONNECTION GUIDE A91FQUF
1EM327017
X10
REGISTRATION CARD A01P5UF
1EMN26042A
X12
WALL MOUNT INSTRUCTION A01F9MF
1EMN26240
20100423
14-23
A01FECA
Electrical Parts
PRODUCT SAFETY NOTE: Products marked with a
# have special characteristics important to safety.
Before replacing any of these components, read
carefully the product safety notice in this service
manual. Don't degrade the safety of the product
through improper servicing.
NOTES:
1. Parts that are not assigned part numbers (---------)
are not available.
2. Tolerance of Capacitors and Resistors are noted
with the following symbols.
C.....±0.25%
D.....±0.5%
F.....±1%
G.....±2%
J......±5%
K.....±10%
M.....±20%
N.....±30%
Z.....+80/-20%
Different parts from the original model
32PFL3505D/F7 (Serial No. : DS1A)
Ref. No.
Description
Part No.
INVERTER ASSEMBLY
Consists of the following
A01F9M1V-001
INVERTER CBA
A01F9M1V-001-IV
------------------------------------------------------------- ----------------------------------A01F9M1V-001-FNIRJN
FUNCTION CBA
IR SENSOR CBA
JUNCTION CBA
20100423
14-24
A01FEEL
REVISION HISTORY
Chassis PL10.3
• 2009-11-26
32PFL3505D/F7 (Serial No. : DS1A**********) added
• 2010-02-10
32PFL3505D/F7 (Serial No. : DS1A**********) : B44 is added.
• 2010-05-14
32PFL3505D/F7 (Serial No. : DS2A**********) added
• 2010-05-14
32PFL3505D/F7 (Serial No. : YA1A**********) added
• 2010-05-14
32PFL3515D/F7 (Serial No. : YA1A**********) added
• 2010-06-24
Corrected the ELECTRICAL PARTS LIST
Deleted service parts numbers (POWER SUPPLY CBA, JACK CBA)
• 2010-08-03
32PFL3505D/F7 (Serial No. : DS4A**********) added
• 2010-11-15
32PFL3505D/F7 (Serial No. : DS8A**********) added
• 2010-11-15
32PFL3505D/F7 (Serial No. : YA2A**********) added
• 2010-12-02
32PFL3505D/F7 (Serial No. : DS9A**********) added
• TBD
32PFL3505D/F7 (Serial No. : DS3A**********) added
• TBD
32PFL3505D/F7 (Serial No. : YA4A**********) added
15-1
PL10.3REV
COMPARISON LIST OF MODEL NAME
Chassis PL10.3
32PFL3505D/F7
32PFL3515D/F7
(DS1A)
A01F2UH
(DS2A)
A01FBUH
(DS3A)
A01FCUH
(DS4A)
A01FDUH
(DS8A)
A01FDUH
(DS9A)
A0RF2UH
(YA1A)
A01F9MF
(YA2A)
A01FUMF
(YA4A)
A0RF3MF
(YA1A)
A01FEMF
PL10.3COM