Shure M98ED User guide
Add to My manuals16 Pages
Shure M98ED is a high-fidelity magnetic cartridge designed for use with all high-fidelity amplifiers having magnetic and constant velocity inputs. It features a wide frequency response from 20 to 20,000 Hz, delivering a 4.7 millivolts output voltage per channel at 1,000 Hz. The cartridge's elliptical stylus provides excellent tracking capability, with a range of 3/4 to 1-1/2 grams tracking force. The recommended optimum load is 47,000 ohms resistance in parallel with 400 to 500 picofarads total capacitance per channel. The cartridge has a standard 1/2-inch mounting center and weighs 6.3 grams.
advertisement
MODEL M98ED T-2
CUSTOM MAGNETIC
CARTRIDGE
BlRADlAL (ELLIPTICAL) STYLUS
DATA SHEET
FREQUENCY RESPONSE:
From 20 to 20,000 Hz
OUTPUT VOLTAGE:
4 7 millivolts per channel at 1,000 Hz at 5 crnJsec peak recorded velocity
STYLUS: Model N95ED B~radial (Ellipt~cal)
Side Contact Radius:
5
microns (.0002 in.)
Frontal Radius: 18 microns (.0007 in.)
Grip Color: Yellow
TRACKABILITY:
This indicates h o w well a stylus can follow or track the signals i n a record groove without losing con- tact. To provide an unbroken f l o w o f signals from the record, the phonograph cartridge nlust be able to track the grooves. Signals recorded at a higher level (measured i n cm/sec peak recorded veloc- ity) are more difficult to track.
M98ED T-2 at a stylus force of 1 gram (ln cm/sec peak recorded veloc~ty):
400 Hz
1,000 Hz
10,000 Hz
-
-
- cm/sec
(Higher stylus forces within specified range im- prove trackability.)
TRACKING FORCE RANGE:
3/4 to 1-1/2 grams
This is the amount of force required of the stylus tip to properly play a record. The lighter the track- ing force within the recommended range, the longer the life of the stylus and records, provided that tracking is maintained.
CHANNEL SEPARATION (minimum):
25 dB at 1,000
Hz
INDUCTANCE:
650 millihenries
D.C. RESISTANCE
1550 ohms
OPTIMUM
LOAD:
47,000 ohms resistance i n parallel with 400 to 500 picofarads total capacitance per channel. Load re- sistance can be up t o 70,000 ohms w i t h almost n o audible change i n frequency response. Total ca- pacitance includes both tone arm wiring and amplifier input circuit.
MOUNTING:
12.7 mm (standard 1/2 in.) mounting centers
WEIGHT:
6.3 grams
TERMINALS:
4 terminals
OPERATION:
The M98ED T-2 DYNETIC@ phonograph cartridges have been developed for use with all high fidelity amplifiers h a v ~ n g magnetic and constant velocity inputs. Recommended track~ng force is 314 to
1 - 7 / 2 grams. Forces greater than 1-1/2 grams should not
be
used.
Mounting
The M98ED T-2 DYNETIC@ Cartridge has 12.7 mm
(standard 1 / 2 in.) mounting centers. Hardware is supplied w i t h each cartridge for mounting pur- poses I n some tone arms and plug-in shells, the cartridge sits so deep that the stylus cannot be conveniently replaced. For these applications, spac- ers are provided t o insure adequate clearance for stylus removal.
For optimum vertical tracking angle, the cartridge should be mounted so the top o f the mounting block is parallel to the record playing surface.
Connections
4-LEAD STEREO CONNECTION: Connect "hot" lead
(usually red) of right channel to terminal "R" and shield or ground lead of right channel (usually green) to terminal "RG". Connect "hot" lead of left channel (usually white) to terminal "L" and h e l d or ground lead of left channel (usually blue) to
"LC".
To prevent "ground loops" and hum, no common connection should be used at cartridge terminals.
MONOPHONIC OPERATION: For monophonic play- back, connect left and right channels i n parallel.
This is accomplished most conveniently by setting function switch on associated amplifier to " A t B " o r "MONO".
CAUTION:
D o not make solder connections t o car- tridge terminals.
LEFT M
(WHITE M W L
L
E F T WmUEL
GROLKl
(B2.E RING1
T E R M I N A L DIAGRAM
F I G U R E I
RlWT M W E L
IRED M W )
W T C M L
G R a Y O
(OREEN RING1
GROVO Tbn
DROVOED TO m3€
S T Y L U S R E P L A C E M E N T
F I G U R E 2
Recommended
Stylus
Cleaning
Use a camel's hair brush (No. 2 size o r smaller), trimmed to approximately 6 mm (1/4 in.) dipped i n alcohol o r an alcohol-distilled water solution.
Commercial cleaning solutions may cause stylus damage o r corrosion. The alcohol w i l l remove any sludge deposit coating the stylus tip. Always brush stylus from back to front; never brush o r wipe stylus from front to back o r side to side.
Easy
Stylus
Replacement (see
Figure
2)
Grasp molded housing o f stylus between thumb and forefinger. Gently withdraw stylus by pulling forward out of cartridge. Grasp replacement stylus between thumb and forefinger and insert into sty- lus socket. Press stylus into socket until the molded housing of the stylus mates w i t h the cartridge case.
Care must be taken not to allow the finger to slip off the molded housing o f the stylus, resulting i n damage to the stylus t i p o r shank.
SPECIAL NOTE: To maintain .the original perform- ance standards of your cartridge, be certain that any replacement stylus you buy is precision manu- factured by Shure Brothers Inc. AVOID INFERIOR
IMITATIONS. THEY WILL SERIOUSLY DEGRADE
THE PERFORMANCE OF YOUR CARTRIDGE. ALL
GENUINE "DYNETIC@" STYLI ARE MANUFAC-
TURED BY SHURE BROTHERS INC. LOOK FOR THE
NAME SHURE O N THE STYLUS GRIP. For more information on your Shure stylus, write for book- let: "A Visit to the Small World of a Stylus."
FULL ONE YEAR WARRANTY: Shure Brothers Incor- porated ("Shure"), 222 Hartrey Avenue, Evanston, llllnois be free, in normal use, of any defects in workmanship chase. You should retaln proof of date of purchase. Shure
1s product has any defects as described above, carefully re- pack the unlt and return i t prepaid to:
Shure Brothers Incorporated
Attention Service Department
1501 West Shure Drive
Arlington Heights, lllinols 60004
If you are not i n the United States, return the untt to your dealer o r Authorized Service Center f o r repair. The promptly, and i f i t cannot be repalred or replaced, you may elect t o receive a refund This warranty does not include stylus wear.
PATENT NOTICE: Cartridge and stylus manufactured under one or more of the following U.S. Patents
3,055,988, 3,077,521, 3,077,522 and 3,463,889.
Manufactured by Shure Brothers Inc.
222 Hartrey Ave., Evanston, IL 60204 U.S.A.
C O P Y R I G H T 1978. SHURE BROTHERS I N C .
2 7 A 1 4 6 3 ( R I ) PRINTED I N U . A .
advertisement
Related manuals
advertisement