Bosch IntuiKey Installation guide

VIDOS IntuiKey
Installation and Operating Manual
Copyright
This document is the intellectual property of Bosch Security Systems and is
protected by copyright. All rights reserved. No part of this document may be
reproduced or transmitted for any purpose, by whatever means, electronic or
mechanical, without the express written permission of Bosch Security Systems.
Release: September 2005 (corresponding to VIDOS Software version 3.0)
© Copyright 2005 Bosch Security Systems
Note
This document has been compiled with great care and the information it
contains has been thoroughly verified. The text was complete and correct at the
time of printing. The ongoing development of the products may mean that the
content of the document can change without notice. Bosch Security Systems
accepts no liability for damage resulting directly or indirectly from faults,
incompleteness or discrepancies between the document and the product
described.
Trademarks
All hardware and software product names used in this document are likely to be
registered trademarks and must be treated accordingly.
Installation and Operating Manual | VIDOS IntuiKey
EN | 1
Contents
Chapter 1 Introduction
3
About this manual. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
VIDOS IntuiKey . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
The control panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Chapter 2 Installation and Setup
7
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
VIDOS IntuiKey in use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Preparatory work in VIDOS . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Chapter 3 Monitoring with VIDOS IntuiKey
19
Login. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Entries with the keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Additional actions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Chapter 4 Contacts and Service (Address)
29
Contact address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Service and support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Index
Bosch Security Systems | 2005-09 | V3.0
31
EN | 2
Installation and Operating Manual | VIDOS IntuiKey
Bosch Security Systems | 2005-09 | V3.0
Installation and Operating Manual | VIDOS IntuiKey
Introduction
EN | 3
1
About this manual
This manual is intended for persons responsible for setting up and using the
BOSCH IntuiKey digital control panel for use with VIDOS. In the following it
therefore is referred to as VIDOS IntuiKey in order to point out that all information
is limited to the work carried out in association with VIDOS. This manual
describes the setup and operation of the VIDOS IntuiKey control panel.
In addition, you should refer to the general documentation supplied with the
control panel and the safety instructions it contains.
Conventions in this manual
The following symbols and notations highlight important situations and
information:
Warning!
Safety instructions where non-compliance can result in damage to the unit
are marked with this symbol.
Note
This symbol indicates special features and provides tips and information
for easier, more convenient use of the software.
Terms that you can find in the program, e.g. menu options or commands, are
written in bold.
References to other documents or other points in this document are written in
SMALL CAPITALS.
If you have any questions about the programs from the VIDOS Pro Suite, you
can find further information on the Internet at:
www.vidos.net
There, you will also find information about new releases or manual versions. You
can also submit your suggestions and comments relating to this document so
that these can be taken into account for future editions.
Bosch Security Systems | 2005-09 | V3.0
EN | 4
Installation and Operating Manual | VIDOS IntuiKey
VIDOS IntuiKey
The VIDOS video management system allows integration of the BOSCH
IntuiKey digital control panel. Within a VIDOS system, the user can thus control
installed cameras, connect cameras and salvos to monitors, navigate between
site maps and trigger other actions he is permitted to perform. Knowledge of
VIDOS or any other programs is not required. Only the individually designed
work area needs to be documented for the user.
The software enabling control using VIDOS IntuiKey is automatically installed
along with VIDOS. For details of integration into VIDOS and setting up the work
area, refer to the following additional documentation:
BOSCH IntuiKey
General documentation for control panel
VIDOS
Describes the basic setup of a the system, e.g.
integration of cameras and hardware monitors,
setting up salvos and planning recordings.
Site maps
Describes the creation of site maps in VIDOS.
Alarm management
Describes alarm management in VIDOS, e.g.
creating triggers and alarm scenarios.
Camera documentation
You obtain separate documentation for each
camera from the manufacturer.
VideoJet, VIP, etc.
You obtain documentation for each device from
Bosch. This explains the typical device settings.
This document is divided into two sections:
INSTALLATION AND SETUP
and
MONITORING WITH VIDOS INTUIKEY.
As the administrator of a VIDOS system, starting on page 7 all information is
provided that you will need to set up a VIDOS work area in such a way that it can
be used with the BOSCH IntuiKey digital control panel.
As a user, starting on page 19 you will find all the necessary information to use
the control panel.
Bosch Security Systems | 2005-09 | V3.0
Installation and Operating Manual | VIDOS IntuiKey
EN | 5
The control panel
Warning!
Make sure that the BOSCH IntuiKey digital control panel you are using has
at least firmware version 1.60. Control panels with older firmware versions
cannot be used in conjunction with VIDOS.
This documentation refers to keys and displays on the control panel. Here is a
brief overview of the control panel:
Soft key display
Status display
Function keys:
Prod Product search
Mon Monitor selection
Shot Call up preset
Alarm
Clr Delete entry
Soft keys
Number keys and
↵ (Enter)
Next to the status display, you will find the joystick for panning, tilting and
zooming, as well as keys for setting the focus and iris on the active camera.
Bosch Security Systems | 2005-09 | V3.0
EN | 6
Installation and Operating Manual | VIDOS IntuiKey
Bosch Security Systems | 2005-09 | V3.0
Installation and Operating Manual | VIDOS IntuiKey
Installation and Setup
EN | 7
2
This section is aimed at the administrator of a VIDOS system. It describes the
setup of a VIDOS workstation operated using the digital control panel.
Once the workstation has been set up, the user typically has no access to a
mouse or PC keyboard. The VIDOS user interface is not part of the work area
for monitoring personnel. As an administrator, your task is to design the work
area for the monitoring personnel in such a way that VIDOS IntuiKey can be
used to perform all operations that are necessary for monitoring.
To do this, you need to familiarize yourself with control using the control panel.
This is the only way that you will be able to create an appropriate work area for
the user. Refer to the description starting on page 19 of this document.
Requirements for setting up a VIDOS IntuiKey workstation:
– You have administrator privileges for VIDOS.
– You are familiar with the VIDOS program and have already created the items
to be operated using VIDOS IntuiKey in VIDOS, e.g. cameras, salvos,
monitors or site maps.
For detailed information about VIDOS refer to the separate documentation
VIDOS or the ONLINE HELP for VIDOS.
Bosch Security Systems | 2005-09 | V3.0
Installation and Setup
EN | 8
Installation and Operating Manual | VIDOS IntuiKey
Installation
Below, you will find a brief overview of the installation and connection of the
control panel. For complete information, refer to the DEVICE DOCUMENTATION FOR
THE BOSCH INTUIKEY CONTROL PANEL.
Purchasing and entering a license
In order to be able to use the BOSCH IntuiKey digital control panel in conjunction
with VIDOS, you must purchase the corresponding license. Once you have
obtained the activation code for BOSCH IntuiKey and entered this in the License
Viewer, you can add the control panel to the VIDOS system as a new device.
For detailed information about licensing, refer to the QUICK INSTALLATION GUIDE
supplied with the VIDOS Pro Suite product CD.
Integrating the control panel into VIDOS
For detailed information about integrating the control panel into the VIDOS
system, refer to the user guide for VIDOS in the section entitled INTEGRATING THE
BOSCH INTUIKEY DIGITAL CONTROL PANEL, here is a brief summary:
1. Start the VIDOS program.
2. Click on System > Configuration….
You will see the Configuration window.
3. Right click on Devices and select New.
You will see the Select object selection dialog.
4. In this dialog box, select Bosch IntuiKey.
5. Click on OK.
You will see the General tab in the Create new Bosch IntuiKey dialog box.
6. Give the device a descriptive name and if necessary enter a description.
7. Click on the Device tab.
8. Enable the device by checking the field in front of Receive Commands from
Keyboard.
9. Select the COM port used to connect the control panel to the PC.
Installation and Setup
Bosch Security Systems | 2005-09 | V3.0
Installation and Operating Manual | VIDOS IntuiKey
EN | 9
10.Click on OK.
The control panel is integrated into the system and is displayed in the VIDOS
system tree under Devices.
Bosch Security Systems | 2005-09 | V3.0
Installation and Setup
EN | 10
Installation and Operating Manual | VIDOS IntuiKey
Connecting and starting the control panel
Warning!
Make sure that the BOSCH IntuiKey digital control panel you are using has
at least firmware version 1.60. Control panels with older firmware versions
cannot be used in conjunction with VIDOS.
1. Connect a COM port on the PC on which VIDOS is installed to the RS232
serial port on the rear of the control panel using the appropriate cable.
Note
Use a fully occupied serial cable (9-wire) for the connection.
2. Make sure that the power supply unit provided is used to power the control
panel.
As soon as the power supply is connected, the control panel is active.
3. Make sure that VIDOS is started on the PC.
4. Press the Prod key on the control panel.
The control panel starts the search for products with which it can
communicate. VIDOS is found.
In the top left of the soft key display on the control panel, you will find the
option Terminal.
5. Press the Terminal soft key to use the control panel in conjunction with
VIDOS.
The main menu will then appear in the soft key display.
Note
The Keyboard control option allows you to test the control panel. This
option is described in the DEVICE DOCUMENTATION FOR THE BOSCH
INTUIKEY CONTROL PANEL.
Installation and Setup
Bosch Security Systems | 2005-09 | V3.0
Installation and Operating Manual | VIDOS IntuiKey
EN | 11
VIDOS IntuiKey in use
VIDOS IntuiKey and analog monitors
The digital control panel is used to connect cameras and salvos to analog
hardware monitors and to control cameras. When used in this way, the user has
no points of contact with the PC.
The user sees only
the control panel and monitors.
He knows the numbers of
cameras, salvos and monitors.
VIDOS remains
hidden from the user
Working with a site map
In this case, the user works with a digital monitor, e.g. the PC monitor. The
mouse and keyboard can be available but do not need to be. The VIDOS
program remains hidden from the user. The user can call up site maps using
their numbers.
Bosch Security Systems | 2005-09 | V3.0
Installation and Setup
EN | 12
Installation and Operating Manual | VIDOS IntuiKey
Preparatory work in VIDOS
For the user to be able to perform his tasks using the VIDOS IntuiKey, all items
to which he is to have access must be given numbers. The assignment of these
numbers is described below.
The following table provides an overview of the items that can be operated using
VIDOS IntuiKey:
Item
Number/Keyboard ID specified in …
Camera
Properties dialog box in system tree
Salvo
Properties dialog box
in Configuration window
Hardware monitor
Properties dialog box in system tree
Site map
Properties dialog box in system tree
Software monitor window
kbid property in site map editor
Preparing cameras and hardware monitors
1. Start the VIDOS program.
2. In the system tree, right click on a camera or encoder.
3. Select Properties.
Installation and Setup
Bosch Security Systems | 2005-09 | V3.0
Installation and Operating Manual | VIDOS IntuiKey
EN | 13
4. In the Properties dialog box, assign the camera or the encoder a number.
It makes sense to start the numbering from 1 and to assign successive
numbers to subsequent cameras. The user can then use the Previous/Next
camera soft keys to successively connect cameras to a monitor.
5. Close the Properties dialog box with OK.
6. Repeat steps 2 to 5 for each installed camera to which the user will be given
access.
7. Repeat steps 2 to 5 for each installed hardware monitor.
Once again, it makes sense for the first monitor to be given the number 1 and
all subsequent monitors to be numbered consecutively.
8. VIDOS is not closed – if the VIDOS IntuiKey is used to make connections,
VIDOS controls the connection between cameras and monitors in the
background.
Bosch Security Systems | 2005-09 | V3.0
Installation and Setup
EN | 14
Installation and Operating Manual | VIDOS IntuiKey
Preparing salvos
1. Start the VIDOS program.
2. Click on System > Configuration….
You will see the Configuration window.
3. Click on Salvos.
All salvos are displayed in the right-hand section of the window.
4. Click on Properties in the popup menu for the desired salvo.
5. In the Properties dialog box, assign the salvo a number.
Salvos are activated in exactly the same way as cameras. A salvo may not
be given the same number as a camera.
Note
If a salvo has several outputs, output 1 is connected to the selected
monitor and all subsequent outputs are successively connected to the next
monitors in numerical order.
6. Repeat steps 4 to 5 for each salvo to which the user will be given access.
7. VIDOS is not closed – if the VIDOS IntuiKey is now used to make
connections, VIDOS controls the connection between salvos and monitors in
the background.
Installation and Setup
Bosch Security Systems | 2005-09 | V3.0
Installation and Operating Manual | VIDOS IntuiKey
EN | 15
Preparing site maps
For users who work on digital screens, a work area consisting of one or more
site maps can be set up in VIDOS. This work area is typically shown in fullscreen mode. The user can use VIDOS IntuiKey to navigate between the
different site maps.
Each site map is given a number. The procedure for this is as described above
under PREPARING CAMERAS AND HARDWARE MONITORS. Below, you can see a
typical example of the Properties dialog box for a site map:
Number
This number is entered on the
control panel to call up this site
map.
Hardware and software monitor windows can also be embedded in the site
maps, on which the user can operate VIDOS IntuiKey to connect cameras or
salvos.
The hardware monitors are given their specific numbers as described above.
The software monitor windows are assigned numbers in the site map editor
using the kbid property. (For details, refer to the separate SITE MAPS
documentation).
Note
If several site maps belong to a work area, there may be a monitor window
with the number 1 on each of these site maps – but this monitor number
may only be assigned once within each individual site map.
Administration is easier if you only assign each number once.
Software monitor windows also provide an option for instant replay of
recordings, which can be started and controlled using VIDOS IntuiKey (for
details see INSTANT REPLAY AND BACKUP).
Bosch Security Systems | 2005-09 | V3.0
Installation and Setup
EN | 16
Installation and Operating Manual | VIDOS IntuiKey
Alarm management
The user has the option of responding to alarms that accumulate on the alarm
stack. He can acknowledge them using the (Alarm) key, trigger alarm
scenarios and disable the alarms.
Document all the operations relating to alarms in a way that will be clear and
understandable for the user.
For details of setting up alarm triggers and alarm scenarios, refer to the separate
ALARM MANAGEMENT documentation.
Setting up camera presets
The control panel allows the user to call up fixed camera positions, known as
presets. For details of setting up presets, refer to the separate documentation
VIDOS.
Note
The user can only call up presets if he has been assigned authorization for
camera control in VIDOS. However, he can then also use VIDOS IntuiKey
to access the Camera control menu, which he can use to change the
presets.
Recordings and snapshots
The control panel allows the user to create snapshots from live video recordings.
Recordings are saved on an NVR, which you need to configure in VIDOS.
Snapshots are saved in the default VIDOS directory. You cannot change this
path. For details about configuration of an NVR and the management and
playback of snapshots, refer to the separate documentation VIDOS.
Instant replay and backup
The control panel gives the user the option of starting instant replay in software
monitor windows, if local recording from the camera is active and he has the
necessary authorizations. As an administrator, you must ensure that these
requirements are met. For details of the configuration of local recordings, refer
to the corresponding DEVICE MANUALS (e.g. VideoJet or VIP) and the separate
documentation VIDOS.
The user can operate the Backup soft key to make backups of replayed
recordings on an NVR. To do this, you must configure a corresponding NVR in
VIDOS (for details see the separate documentation VIDOS).
Installation and Setup
Bosch Security Systems | 2005-09 | V3.0
Installation and Operating Manual | VIDOS IntuiKey
EN | 17
Setting up users and authorizations
The control panel allows you to log into VIDOS as a user.
Users and authorizations are set up in VIDOS (for details, see the separate
documentation VIDOS). Note that for users who will log in using VIDOS IntuiKey,
the login name and password must consist exclusively of figures.
Example: Name 2508, Password 1905.
It is always necessary to log in using the control panel if the Authorization
required dialog box appears in VIDOS.
Login is also necessary if the previous user pressed the Log off soft key in the
main menu (this corresponds to the Change user operation in VIDOS).
Note
Make sure that users with extended authorizations log off in this way after
completing their work on the VIDOS IntuiKey, so that subsequent users
cannot perform any unauthorized actions.
Final steps
Before you transfer the workstation to the user, note the following:
„
Test the control panel on the workstation under genuine conditions.
Have the work area tested by someone else.
„
Make sure that if site map based operation is to be used on the PC, no
screensaver is active. The user will not be able to exit it.
Bosch Security Systems | 2005-09 | V3.0
Installation and Setup
EN | 18
Installation and Setup
Installation and Operating Manual | VIDOS IntuiKey
Bosch Security Systems | 2005-09 | V3.0
Installation and Operating Manual | VIDOS IntuiKey
EN | 19
3
Monitoring with VIDOS IntuiKey
This section is intended for persons who will operate the VIDOS IntuiKey. A
workstation with VIDOS and the VIDOS IntuiKey digital control panel is set up.
Login
The control panel and, if necessary, the work area are already started and ready
for operation.
1. If necessary, log in with your user ID. Enter the sequence of digits and confirm
by pressing the ↵ (Enter) key.
User
–
VIDOS
Enter ID:
Bosch Security Systems | 2005-09 | V3.0
Monitoring with VIDOS IntuiKey
EN | 20
Installation and Operating Manual | VIDOS IntuiKey
2. Then enter the sequence of digits for your password and confirm by pressing
the ↵ (Enter) key.
Password
–
VIDOS
Enter password:
3. The options for VIDOS are shown in the soft key display.
In the status display, Monitor 1 is shown as active:
Monitor
Camera
1
–
VIDOS
Monitoring with VIDOS IntuiKey
Bosch Security Systems | 2005-09 | V3.0
Installation and Operating Manual | VIDOS IntuiKey
EN | 21
Entries with the keyboard
This section explains the keys on the control panel. It illustrates how the
keyboard on the control panel can be used to make entries.
Function keys
These function keys are available on the keyboard with predefined functions:
Key
Function
Prod
Starts the search for products that are compatible with VIDOS
IntuiKey.
Press this key if the connection to VIDOS has been
interrupted. Then press the Terminal soft key to return to the
VIDOS main menu.
Mon
Press this key to select a monitor.
Clr
Press this key to delete your last entry made with the number
keys.
Press this key after turning on the control panel to shorten the
start-up routine.
(Alarm)
Shot
↵ (Enter)
This key lights up red if alarms have accumulated on the alarm
stack. You can process these alarms by repeatedly pressing
the key (detailed information is available from your system
administrator).
Press this key to call up a preset (fixed camera position).
Press this key to complete and confirm an entry with the
number keys.
Bosch Security Systems | 2005-09 | V3.0
Monitoring with VIDOS IntuiKey
EN | 22
Installation and Operating Manual | VIDOS IntuiKey
Example: Display camera on monitor
This sequence of entries shows an example of how the data sent from a camera
is displayed on a monitor.
1. Press Mon.
2. Enter the number of the monitor.
If you make a typing error, press Clr and enter the number again.
3. Press ↵ (Enter) to confirm the entry.
The control panel now expects you to enter the number for the camera.
4. Enter the number of the camera you want to connect.
If you make a typing error, press Clr and enter the number again.
5. Press ↵ (Enter) to confirm the entry.
The data from the camera is displayed in the selected monitor window.
Note
A salvo is connected in the same way as a camera. Instead of the camera
number enter the number of the salvo.
If a salvo has several outputs, output 1 is connected to the selected
monitor and all subsequent outputs are successively connected to the next
monitors in numerical order.
Controlling the camera
You can control controllable cameras using the joystick as soon as they are
connected to the active monitor:
– Push the joystick in the desired direction to pan or tilt the camera.
A firmer push speeds up the camera's movement.
– Rotate the head of the joystick to zoom in or out.
Monitoring with VIDOS IntuiKey
Bosch Security Systems | 2005-09 | V3.0
Installation and Operating Manual | VIDOS IntuiKey
EN | 23
Calling up a camera preset
Fixed positions can be set for controllable cameras. You can enter these socalled presets yourself using the Camera Control soft key. You can call up
presets as soon as the camera is connected to the active monitor.
1. Press Shot.
The prompt Go to setting appears in the status display.
2. Enter the number of the desired preset.
If you make a typing error, press Clr and enter the number again.
3. Press ↵ (Enter) to confirm the entry.
The camera moves to the selected position.
Soft keys
The soft keys are available for selecting from menus or for choosing other
commands. The function of a soft key can change. It depends on which menu is
currently active.
The current function of a soft key is always indicated in the soft key display.
The upper section of the soft key display always shows the following commands:
Main Menu
Camera
Control
Site map
navigation
Replay
The functions of the keys in the lower section of the display change depending
on the selected menu.
Bosch Security Systems | 2005-09 | V3.0
Monitoring with VIDOS IntuiKey
EN | 24
Installation and Operating Manual | VIDOS IntuiKey
Main menu
These commands are available in the main menu:
Command
Description
Logout
Logs you off from VIDOS.
Press the soft key for approximately 2 seconds.
Once you have logged off, a different user can log in
(details on page 19).
Talk
You can communicate with a person who is at the location
of the active camera (only possible if both locations are set
up for voice connections).
Hold down the key while you are talking.
When the key is not pressed, you will hear the person at the
location of the active camera.
Note
Turn off the key click as this can result in unwanted noise (for details, refer
to general DOCUMENTATION FOR BOSCH INTUIKEY).
Record
Starts a recording of the data from the active camera. This
function is not supported with every configuration.
If the active camera is currently recording, the menu option
is displayed inversely.
Press the key a second time to stop recording. Recording
is also stopped if you change to a different camera.
Snapshot
Takes a snapshot of the current scene from the active
camera.
Previous camera
The data from the previous/next camera is displayed in the
active monitor. The display scrolls through the cameras in
the order of their camera numbers. If the first/last camera is
displayed, you cannot scroll any further.
Next camera
Note
Commands associated with a monitor or a camera always relate to the
active monitor and the active camera. These are shown in the status
display.
Monitoring with VIDOS IntuiKey
Bosch Security Systems | 2005-09 | V3.0
Installation and Operating Manual | VIDOS IntuiKey
EN | 25
Camera control
This soft key calls up the camera control menu. The assignment of the soft keys
in the lower section of the soft key display differs depending on the capabilities
of the active camera and your authorizations.
Here, you have the opportunity to set and delete presets. With some cameras,
you can display a menu on the monitor.
Site map navigation
This menu option is relevant to you if you are working on a digital monitor, e.g.
the PC monitor.
This soft key is used to open the menu that allows you to selectively call up a
site map. You have the following options:
Command
Description
Load up site map
Site map appears in the status display and you can call up
the desired site map by entering the number.
Note
The display remains unchanged if you have entered a figure that is not
assigned to a site map.
Previous site map This soft key is used to return to the last active site map.
Replay
This menu option is relevant to you if you are working with site maps using
embedded software monitor windows. Playback is only possible in software
monitor windows.
Note
This function is only available if an active recording is running for the
selected camera.
Bosch Security Systems | 2005-09 | V3.0
Monitoring with VIDOS IntuiKey
EN | 26
Installation and Operating Manual | VIDOS IntuiKey
As soon as you press the soft key, instant replay is activated for the selected
camera in the active software monitor window. The associated menu appears in
the soft key display.
These commands are available in the Replay menu:
Command
Description
Previous frame
The previous frame is displayed.
Next frame
The next frame is displayed.
Pause
Play
Pauses / continues playback.
Backup
Starts backing up the sequence.
To do this an NVR must be configured in VIDOS, otherwise
you will see a message in the soft key display.
In point
Sets the starting point for the sequence you want to back
up.
Out point
Sets the end point for the sequence you want to back up.
Monitoring with VIDOS IntuiKey
Bosch Security Systems | 2005-09 | V3.0
Installation and Operating Manual | VIDOS IntuiKey
EN | 27
Additional actions
Disconnect
If you no longer want data to be displayed on a monitor, proceed as follows:
1. Press Mon.
2. Enter the number of the monitor.
If you make a typing error, press Clr and enter the number again.
3. Press ↵ (Enter) to confirm the entry.
The control panel now expects you to enter the number for the camera.
4. Enter 0 [zero] as the number of the camera you want to connect.
5. Press ↵ (Enter) to confirm the entry.
No more video data is displayed on the monitor.
Bosch Security Systems | 2005-09 | V3.0
Monitoring with VIDOS IntuiKey
EN | 28
Monitoring with VIDOS IntuiKey
Installation and Operating Manual | VIDOS IntuiKey
Bosch Security Systems | 2005-09 | V3.0
Installation and User Guide | VIDOS IntuiKey
Contacts and Service (Address)
EN | 29
4
Contact address
Bosch Sicherheitssysteme GmbH
Robert-Koch-Straße 100
85521 Ottobrunn
Germany
E-mail:
Internet:
de.securitysystems@bosch.com
www.bosch-sicherheitssysteme.de
Bosch Security Systems | 2005-09 | V3.0
Contacts and Service (Address)
EN | 30
Installation and User Guide | VIDOS IntuiKey
Service and support
If you have any questions about the programs from the VIDOS Pro Suite, you
can find further information on the Internet at:
www.vidos.net
Technical support is available from:
Americas
Bosch Security Systems
130 Perinton Parkway
Fairport, New York, 14450, USA
Phone:
Fax:
+1 585 223 4060
+1 585 223 9180
E-mail:
Internet:
security.sales@us.bosch.com
www.boschsecurity.us
Europe, Middle East, Africa
Bosch Security SystemsB.V.
P.O. Box 8000
25600 JB Eindhoven, The Netherlands
Phone:
Fax.
+31 (0)40 27 83955
+31 (0)40 27 86668
E-mail:
Internet:
emea.securitysystems@bosch.com
www.boschsecurity.com
Asia-Pacific
Bosch Security Systems Pte Ltd
38C Jalan Pemimpin
Singapore 577180
Phone:
Fax:
+65 6319 3450
+65 6319 3499
E-mail:
Internet:
apr.securitysystems@bosch.com
www..boschsecurity.com
Contacts and Service (Address)
Bosch Security Systems | 2005-09 | V3.0
Installation and Operating Manual | VIDOS IntuiKey
EN | 31
Index
A
Alarm processing
Method .................................. 21
preparing ............................... 16
Authentication ............................. 17
H
Hardware monitor
preparing ............................... 12
I
In point ........................................ 26
B
Instant replay ........................16, 26
Backup ..................................16, 26
J
C
Camera
Calling up preset ................... 23
controlling .............................. 22
display ................................... 22
next ....................................... 24
preparing ............................... 12
previous ................................ 24
Setting up presets ...........16, 25
Camera control ........................... 25
Clr .................................. 22, 23, 27
Connection
disconnect ............................. 27
establish ................................ 22
Contact address ......................... 29
Control panel
connecting ............................. 10
integration ............................... 8
starting .................................. 10
Joystick ......................................... 5
K
Key
Alarm ......................... 5, 16, 21
Bell symbol ................ 5, 16, 21
Clr .....................................5, 21
Enter .................................5, 21
Mon ...................................5, 21
Prod ..................................5, 21
Shot ..................................5, 21
Keyboard control ........................ 10
L
License ......................................... 8
Log off ..................................17, 24
Login ........................................... 19
M
E
Main menu .................................. 24
Enter ................. 19, 20, 22, 23, 27
Mon ......................................22, 27
F
N
Function keys .........................5, 21
Next Frame ................................. 26
Number keys ................................ 5
Bosch Security Systems | 2005-09 | V3.0
EN | 32
Installation and Operating Manual | VIDOS IntuiKey
Out point ..................................... 26
Software monitor window
preparing ............................... 15
Status display ............................... 5
P
Symbols ........................................ 3
O
Pause ......................................... 26
Play ............................................. 26
T
Preset ...................................16, 23
Talk ............................................. 24
Previous Frame .......................... 26
Prod ............................................ 10
R
Record
starting .................................. 24
Recording
backing up ............................. 26
preparing ............................... 16
Recording backup
In point .................................. 26
Out point ............................... 26
Replay ........................................ 25
S
Salvo ........................................... 22
display ................................... 22
preparing ............................... 14
Screensaver ............................... 17
Service ........................................ 30
Setting up authorizations ............ 17
Setting up users .......................... 17
Shot ............................................ 23
Site map
loading .................................. 25
preparing ............................... 15
previous ................................ 25
Site map Navigation ................... 25
Snapshot ..............................16, 24
Soft key display ............................ 5
Soft keys .................................5, 23
Bosch Security Systems | 2005-09 | V3.0
Bosch Sicherheitssysteme GmbH
Robert-Koch-Straße 100
85521 Ottobrunn
Germany
www.bosch-sicherheitssysteme.de
Bosch Security Systems B.V.
P.O. Box 80002
5600 JB Eindhoven
The Netherlands
www.boschsecuritysystems.com
© 2005 Bosch Sicherheitssysteme GmbH
Subject to change. Printed in Germany.
3504B-IK/0905/en/1