Emerson Series 610 Technical data

Embedded Computing for
Business-Critical ContinuityTM
COMX-CAR-610 COM Express Carrier Board
Installation and Use
P/N: 6806800K26D
August 2011
©
2011 Emerson
All rights reserved.
Trademarks
Emerson, Business-Critical Continuity, Emerson Network Power and the Emerson Network Power logo are trademarks and service
marks of Emerson Electric Co. © 2011 Emerson Electric Co. All other product or service names are the property of their respective
owners.
Intel® is a trademark or registered trademark of Intel Corporation or its subsidiaries in the United States and other countries.
Java™ and all other Java-based marks are trademarks or registered trademarks of Sun Microsystems, Inc. in the U.S. and other
countries.
Microsoft®, Windows® and Windows Me® are registered trademarks of Microsoft Corporation; and Windows XP™ is a trademark of
Microsoft Corporation.
PICMG®, CompactPCI®, AdvancedTCA™ and the PICMG, CompactPCI and AdvancedTCA logos are registered trademarks of the PCI
Industrial Computer Manufacturers Group.
UNIX® is a registered trademark of The Open Group in the United States and other countries.
Notice
While reasonable efforts have been made to assure the accuracy of this document, Emerson assumes no liability resulting from any
omissions in this document, or from the use of the information obtained therein. Emerson reserves the right to revise this document
and to make changes from time to time in the content hereof without obligation of Emerson to notify any person of such revision or
changes.
Electronic versions of this material may be read online, downloaded for personal use, or referenced in another document as a URL to
a Emerson website. The text itself may not be published commercially in print or electronic form, edited, translated, or otherwise
altered without the permission of Emerson,
It is possible that this publication may contain reference to or information about Emerson products (machines and programs),
programming, or services that are not available in your country. Such references or information must not be construed to mean that
Emerson intends to announce such Emerson products, programming, or services in your country.
Limited and Restricted Rights Legend
If the documentation contained herein is supplied, directly or indirectly, to the U.S. Government, the following notice shall apply
unless otherwise agreed to in writing by Emerson.
Use, duplication, or disclosure by the Government is subject to restrictions as set forth in subparagraph (b)(3) of the Rights in
Technical Data clause at DFARS 252.227-7013 (Nov. 1995) and of the Rights in Noncommercial Computer Software and
Documentation clause at DFARS 252.227-7014 (Jun. 1995).
Contact Address
Emerson Network Power - Embedded Computing
2900 South Diablo Way, Suite 190
Tempe, AZ 85282
USA
Contents
About this Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
1
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
1.1
1.2
1.3
1.4
1.5
2
Hardware Preparation and Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
2.1
2.2
2.3
2.4
3
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Standard Compliances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Mechanical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Product Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Environmental and Power Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
2.1.1 Environmental Requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
2.1.2 Power Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Unpacking and Inspecting the Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Installation and Removal of the COM Express Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Replacing the Onboard Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Controls, LEDs, and Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
3.1
3.2
3.3
3.4
Carrier Board Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
COM Express Board-to-Board Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
3.4.1 Video . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
3.4.1.1 LVDS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
3.4.1.2 VGA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
3.4.1.3 HDMI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
3.4.1.4 Display Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
3.4.2 Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
3.4.3 LAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
3.4.4 PCI Express . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
3.4.5 USB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
3.4.5.1 USB 2.0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
3.4.5.2 USB 3.0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
3.4.6 Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D)
3
Contents
Contents
3.4.7
3.5
4
Super I/O. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
3.4.7.1 Fan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
3.4.7.2 PS/2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
3.4.7.3 LPT Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
3.4.7.4 Serial Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
3.4.8 Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Headers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
3.5.1 LPC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
3.5.2 Trusted Platform Module (TPM). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
3.5.3 GPIO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
3.5.4 Miscellaneous I/O . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
3.5.5 SPI Flash . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
3.5.6 EEPROM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
4.1
4.2
Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Video . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
4.2.1 LVDS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
4.2.2 VGA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
4.2.3 HDMI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
4.2.4 Display Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
4.3 Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
4.4 LAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
4.5 PCI Express . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
4.5.1 PCI Express Mini Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
4.6 USB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
4.7 Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
4.8 Super I/O . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
4.8.1 Voltage and Thermal Monitoring. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
4.8.2 Fan Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
4.8.3 PS/2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
4.8.4 LPT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
4.8.5 RS-232 and RS-422/485 Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
4.9 SPI Flash . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
4.10 Watchdog Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
4
COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D)
Contents
4.11 Real Time Clock (RTC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
4.12 Wake Events . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
A
Related Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
A.1
A.2
Emerson Network Power—Embedded Computing Documents . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Manufacturers’ Documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Safety Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Sicherheitshinweise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D)
5
Contents
Contents
6
COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D)
List of Tables
Table 1-1
Table 1-2
Table 2-1
Table 2-2
Table 2-3
Table 3-1
Table 3-2
Table 3-3
Table 3-4
Table 3-5
Table 3-6
Table 3-7
Table 3-8
Table 3-9
Table 3-10
Table 3-11
Table 3-12
Table 3-13
Table 3-14
Table 3-15
Table 3-16
Table 3-17
Table 3-18
Table 3-19
Table 3-20
Table 3-21
Table 3-22
Table 3-23
Table 3-24
Table 3-25
Table 3-26
Table 3-27
Table 3-28
Table 3-29
Table 3-30
Table 3-31
Carrier Board Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Environmental Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Carrier Board Power Consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Current Requirements from the Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
COM Express Connector Pin Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
P8, Backlight Wafer Header Pin Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
P6, LVDS Connector Pin Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
P7, LVDS Power Supply Jumper Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
P35, LVDS Power Supply Jumper Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
J5, VGA Connector Pin Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
J5, HDMI Connector Pin Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
J3 and J4, Display Port Connector Pin Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
J16, Audio Jack Connector Pin Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
P11, Audio Header Pin Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
J1, LAN Connector Pin Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
P9 Jumper Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
P24 Jumper Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
P25 Jumper Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
P2, USB 2.0 Header Pin Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
P1, USB 2.0 Header Pin Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
P39, USB 2.0 Header Pin Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
P10, Jumper Settings for Configuring USB Multiplexed Devices . . . . . . . . . . . . . . . . . . . 40
J14 and J15, USB 3.0 Connector Pin Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
P10—P13, SATA Socket Pin Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
P3 and P27, Fan Header Pin Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
P26, PS/2 (Keyboard and Mouse) Connectors Pin Definition . . . . . . . . . . . . . . . . . . . . . . 42
P32, LPT Header Pin Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
P18—P23, RS-232 Headers Pin Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
P37 and P33, RS-422/RS-485 Headers Pin Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Set Jumpers P34 and P41 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
P40 PS_ON Select Jumper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
ATX Power Supply Connector Pin Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
P29, Low Pin Count (LPC) Header Pin Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
P28, Trusted Platform Module (TPM) Header Pin Definition . . . . . . . . . . . . . . . . . . . . . . . 45
COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D)
7
List of Tables
Table 3-32
Table 3-33
Table 3-34
Table 3-35
Table 3-36
Table 3-37
Table 3-38
Table 4-1
Table A-1
8
P30, GPIO Header Pin Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
P16, Miscellaneous I/O Header Pin Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
P13, SPI Flash Header Pin Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
P12 and P14, Jumper Settings for SPI Flash SF100 header . . . . . . . . . . . . . . . . . . . . . . . . . 47
P15 and P38, Jumper Configuration to Enable/Disable BIOS . . . . . . . . . . . . . . . . . . . . . . . 47
P17 Case Open Select Header . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
P31, EEPROM Header Pin Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Wake Events . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Emerson Network Power, Embedded Computing Publications . . . . . . . . . . . . . . . . . . . . 59
COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D)
List of Figures
Figure 1-1
Figure 1-2
Figure 1-3
Figure 1-4
Figure 3-1
Figure 4-1
Figure 4-2
Figure 4-3
Figure 4-4
Figure 4-5
Figure 4-6
Standard Compliances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
COMX-CORE Series Mechanical Dimensions (Top View) . . . . . . . . . . . . . . . . . . . . . .
COMX-CORE Series Mechanical Dimensions (SideView) . . . . . . . . . . . . . . . . . . . . . .
Location of Product Serial Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
COMX-CAR-610 COM Express Carrier Board Component Layout . . . . . . . . . . . . . . .
COM Express Type 6 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PCI Express Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PCI Express Mini Card Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Super I/O Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SPI Flash Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Watchdog Timer Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D)
17
18
19
20
27
49
51
52
53
55
56
9
List of Figures
10
COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D)
About this Manual
Overview of Contents
This manual is divided into the following chapters and appendices:

Introduction provides an overview of the product’s features.

Hardware Preparation and Installation provides instructions on installing and removing the
module.

Controls, LEDs, and Connectors provides information on the pin assignments of the various
connectors on the board.

Functional Description discusses the functions of various components on the board.

BIOS discusses the functions that are available on the Setup Utility.

Related Documentation lists various documentation relevant to the product.

Safety Notes provides a summary of the safety notices applicable to the product.

Sicherheitshinweise is a German version of the Safety Notes.
Abbreviations
This document uses the following abbreviations:
Abbreviation
Definition
ACPI
Advanced Configuration Power Interface
AMC
Alarm Management Controller
ARP
Address Resolution Protocol
BDS
Boot Device Selection
DDR
Double Data Rate
DXE
Driver Execution Environment
EEPROM
Electrically Erasable Programable Read-Only Memory
eUSB
Embedded Universal Serial Bus
GbE
Gigabit Ethernet
GPIO
General Purpose Input Output
HDMI
High-Definition Multimedia Interface
COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D)
11
About this Manual
About this Manual
12
Abbreviation
Definition
I2C
Inter-Integrated Circuit
I/O
Input/Output
IDE
Integrated Device Electronics
LED
Light Emitting Diode
LIN
Line In
LFM
Linear Feet per Minute
LPT
Line Print Terminal
LOUT
Line Out
LDVS
Low Voltage Differential Signaling
MICIN
Microphone In
NVRAM
Non-volatile RAM
OEM
Original Equipment Manufacturer
PCI
Peripheral Component Interconnect
PCI-E
Peripheral Component Interconnect Express
POST
Power-on Self Test
RTC
Real Time Clock
SATA
Serial AT Attachment
SCSI
Small Computer System Interface
SPD
Serial Presence Detect
SPI
Serial Peripheral Interface
SODIMM
Small Outline Dual In-line Memory Module
Super I/O
Super Input/Output
TPM
Trusted Platform Module
USB
Universal Serial Bus
VGA
Video Graphics Adapter
WDT
Watchdog Timer
COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D)
About this Manual
Conventions
The following table describes the conventions used throughout this manual.
Notation
Description
0x00000000
Typical notation for hexadecimal numbers (digits are
0 through F), for example used for addresses and
offsets
0b0000
Same for binary numbers (digits are 0 and 1)
bold
Used to emphasize a word
Screen
Used for on-screen output and code related elements
or commands in body text
Courier + Bold
Used to characterize user input and to separate it
from system output
Reference
Used for references and for table and figure
descriptions
File > Exit
Notation for selecting a submenu
<text>
Notation for variables and keys
[text]
Notation for software buttons to click on the screen
and parameter description
...
Repeated item for example node 1, node 2, ..., node
12
.
Omission of information from example/command
that is not necessary at the time being
.
.
..
Ranges, for example: 0..4 means one of the integers
0,1,2,3, and 4 (used in registers)
|
Logical OR
COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D)
13
About this Manual
About this Manual
Notation
Description
Indicates a hazardous situation which, if not avoided,
could result in death or serious injury
Indicates a hazardous situation which, if not avoided,
may result in minor or moderate injury
Indicates a property damage message
No danger encountered. Pay attention to important
information
Summary of Changes
This manual has been revised and replaces all prior editions.6806800K26B
Part Number
Publication Date
Description
6806800A36C
January 2006
First edition
6806800K26B
March 2010
GA Version
6806800K26C
November 2010
GA version: Updated Section 3.4.4 PCI Express
6806800K26D
September 2011
Updated Table "P12 and P14, Jumper Settings for
SPI Flash SF100 header" on page 47, Table "P15
and P38, Jumper Configuration to Enable/Disable
BIOS" on page 47.
Added Table "P17 Case Open Select Header" on
page 48 and Table "P40 PS_ON Select Jumper" on
page 44.
14
COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D)
Chapter 1
Introduction
1.1
Features
The COMX-CAR-610 COM Express Carrier Board is a Type 6 carrier board. This board is designed
to support the COM Express Type 6 Specification and is compatible with COM Express Type 1
Specification. This board supports the following COM Express form factors: compact, basic,
and extended.
Table 1-1 Carrier Board Features
Feature
Description
Form factor
MicroATX (9.6'' x 9.6'')
Video

One backlight header for powering a backlight

One LVDS connector

Two Display Port connectors

One VGA and HDMI connector

One audio jack: MICIN,LOUT,LIN

One audio header: MICIN, LOUT

33 MHz clock buffer: ICS9112AM-16

100 MHz clock buffer: ICS9DB108BFLF
Audio
Clock buffer
LPT
One LPT header from Super I/O
KBMS
One keyboard and mouse header
COM

Four RS-232 ports (COM1—COM4)

Two RS-232/RS-422/RS-485 ports (COM5 and COM6)

LAN1—GbE from COM Express module

LAN2—GbE from carrier board (WG82574L)

Four USB3.0 ports

Three USB 2.0 ports (in header)

One eUSB flash (maximum of 8 GB)

One PCI-E x16 slot

Two PCI-E x4 slots

One PCI-E x1 slot
LAN
USB
PCI-E Slots
PCI-E Minicard
One PCI-E Mini-Card for WiFi or WiMax
Serial ATA
Four SATA II ports
COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D)
15
Introduction
Table 1-1 Carrier Board Features (continued)
Feature
Description
Trusted Platform Module
One onboard TPM header
Power supply

One 24-pin ATX power header

One 4-pin ATX_12V header

One battery socket

Three-channel voltage sensors: 5 V, 3.3 V and 12 V

Two-channel temperature sensors: module and system

Two-channel Fan speed Control: Module and system

Compact

Basic

Extended

Power Button: S0, S3, S4, S5

KB: S0, S3

Mouse: S0, S3

PME: S0, S3, S4, S5

USB: S0, S3

Wake on LAN support
Hardware Monitor and Controller
Supported COM Express Form
Factors
Wake-Up Events
16
COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D)
Introduction
1.2
Standard Compliances
Figure 1-1
Standard Compliances
COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D)
17
Introduction
1.3
Mechanical Data
Figure 1-2
18
COMX-CORE Series Mechanical Dimensions (Top View)
COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D)
Introduction
Figure 1-3
1.4
COMX-CORE Series Mechanical Dimensions (SideView)
Ordering Information
Table 1-2 Ordering Information
Orderable Number
Description
COMX-CAR-610
Type 6 COM express carrier board UATX
COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D)
19
Introduction
1.5
Product Identification
The following figure shows the location of the board’s serial number.
Figure 1-4
20
Location of Product Serial Number
COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D)
Chapter 2
Hardware Preparation and Installation
2.1
Environmental and Power Requirements
You must make sure that the board, when operated in your particular system configuration,
meets the environmental requirements specified below.
Operating temperatures refer to the temperature of the air circulating around the board and
not to the component temperature.
Product Damage
2.1.1

High humidity and condensation on surfaces cause short circuits.

Do not operate the system outside the specified environmental limits. Make sure the
product is completely dry and there is no moisture on any surface before applying
power.
Environmental Requirements
Table 2-1 Environmental Requirements
Environmental Factor
Operating
Non-Operating
Temperature
0 to +55°C
-40 to +85°C
Shock
20 g 11 ms sine or saw
Vibration
0.01g ^2/Hz at 5-500 Hz Random
Vibration
Air Flow
400 LFM at 0 to 55°C
Humidity
10-90% (non-condensing)
COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D)
21
Hardware Preparation and Installation
2.1.2
Power Requirements
The following table shows the power consumption of the carrier board without a COM Express
module installed.
Table 2-2 Carrier Board Power Consumption
Item
+5.0V
POWER
+3.3V
POWER
+12V POWER
5V SB POWER
TOTAL POWER
Power
50W
6W
160W
10W
240W Max
Note: Including 120W power dissipation for COM-E module.
The following table lists the onboard voltages that the DC input generates. The table also
provides an estimate of the typical and maximum current required from the power supply.
Table 2-3 Current Requirements from the Power Supply
Supply Voltage
Source
Voltage
Maximum Current
VCC12
ATX power
12 V
13 A
VCC5
ATX power
5V
10 A
VCC3
ATX power
3V
2A
VCC1_5
VCC3
1.5 V
0.5 A
5VSB
ATX power
5V
2A
5VDual
VCC1_5 and 5VSB
5V
10 A
3VDual
VCC3 and 5VSB
3V
1A
VCC1_8
VCC3
1.8 V
0.5 A
22
COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D)
Hardware Preparation and Installation
2.2
Unpacking and Inspecting the Board
Damage of Circuits

Electrostatic discharge and incorrect installation and removal of the product can
damage circuits or shorten its life.

Before touching the product make sure that you are working in an ESD-safe
environment or wearing an ESD wrist strap or ESD shoes. Hold the product by its edges
and do not touch any components or circuits.
1. Verify that you have received all items of your shipment:

Printed Quick Start Guide and Safety Notes

COMX-CAR-610 COM Express Carrier Board

Accessories:
—
Cable, URAT, 2X5PIN housing to DB9PIN connector, with I/O panel, 300MM
length
—
Cable, USB, 2X5PIN housing to USB X 2 connector, with I/O panel, 300MM
length
—
Cable, LPT, 2X13PIN housing to DB25 PIN connector, with I/O panel,
300MM length
—
Cable, PS/2, MINI DIN6P to PS/2 connector, 300MM length
—
COMX-CAR-610 Carrier Board I/O Shield
COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D)
23
Hardware Preparation and Installation
2. Check for damage and report any damage or differences to customer service.
3. Remove the desiccant bag shipped together with the product.
Environmental Damage
2.3

Improper disposal of used products may harm the environment.

Always dispose of used products according to your country’s legislation and
manufacturer’s instructions.
Installation and Removal of the COM Express
Module
The assembled COM Express module with the attached heat spreader is attached to a carrier
board.
Installing the COM Express Module on the Carrier Board
1. Line up the board-to-board connector of the COM Express module with the boardto-board connector of the COMX-CAR-610.
2. Make sure that the interconnectors are properly aligned and that the seven
standoffs have contact with the top of the COMX-CAR-610.
3. Turn over the COM Express module and the COMX-CAR-610.
4. From the backside of the COMX-CAR-610, locate the screw holes.
5. Use the screws to fasten the COM Express module assembly to the COMX-CAR610.
24
COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D)
Hardware Preparation and Installation
Removing the COM Express Module from the Carrier Board
1. Turn over the COM Express module and the COMX-CAR-610.
2. On the back of the COMX-CAR-610, locate the seven screws that connect the
COM Express module to the COMX-CAR-610.
3. Loosen and remove the screws.
4. While holding the edges, pull the COM Express module from the COMX-CAR-610.
COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D)
25
Hardware Preparation and Installation
2.4
Replacing the Onboard Battery
Product Damage

Incorrect replacement of lithium batteries can result in a hazardous explosion.

When exchanging the on-board lithium battery, make sure that the new and the old
battery are exactly the same battery models.

If the respective battery model is not available, contact your local Emerson sales
representative for the availability of alternative officially approved battery models.
PCB and Battery Holder Damage

Removing the battery with a screw driver may damage the PCB or the battery holder.

Do not use a screw driver to remove the battery from its holder.
Data Loss

Installing another battery type than the one that is mounted at product delivery may
cause data loss since other battery types may be specified for other environments or
may have a shorter lifetime.

Only use the same type of lithium battery as is already installed.
1. Remove the old battery.
2. Install the new battery with the plus sign (+) facing up.
3. Dispose of the old battery according to your country’s legislation and in an
environmentally safe way.
26
COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D)
Chapter 3
Controls, LEDs, and Connectors
3.1
Carrier Board Layout
Figure 3-1
COMX-CAR-610 COM Express Carrier Board Component Layout
COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D)
27
Controls, LEDs, and Connectors
3.2
COM Express Board-to-Board Connector
This section details the pin assignments on the COM Express connector based on the Type 6
Specification.
Table 3-1 COM Express Connector Pin Definition
Row
A
B
C
D
1
GND(FIXED)
GND (FIXED)
GND (FIXED)
GND (FIXED)
2
GBE0_MDI3-
GBE0_ACT#
GND
GND
3
GBE0_MDI3+
LPC_FRAME#
USB0_SSRX-
USB0_SSTX-
4
GBE0_LINK100#
LPC_AD0
USB0_SSRX+
USB0_SSTX+
5
GBE0_LINK1000#
LPC_AD1
GND
GND
6
GBE0_MDI2-
LPC_AD2
USB1_SSRX-
USB1_SSTX-
7
GBE0_MDI2+
LPC_AD3
USB1_SSRX+
USB1_SSTX+
8
GBE0_LINK#
LPC_DRQ0#
GND
GND
9
GBE0_MDI1-
LPC_DRQ1#
USB2_SSRX-
USB2_SSTX-
10
GBE0_MDI1+
LPC_CLK
USB2_SSRX+
USB2_SSTX+
11
GND(FIXED)
GND(FIXED)
GND(FIXED)
GND(FIXED)
12
GBE0_MDI0-
PWRBTN#
USB3_SSSRX-
USB3_SSTX-
13
GBE0_MDI0+
SMB_CK
USB3_SSRX+
USB3_SSTX+
14
GBE0_CTREF
SMB_DAT
GND
GND
15
SUS_S3#
SMB_ALERT#
DDI1_PAIR6+
DDI1_AUX+
16
SATA0_TX+
SATA1_TX+
DDI1_PAIR6-
DDI1_AUX-
17
SATA0_TX-
SATA1_TX-
RSVD
RSVD
18
SUS_S4#
SUS_STAT#
RSVD
RSVD
19
SATA0_RX+
SATA1_RX+
PCIE_RX6+
PCIE_TX6+
20
SATA0_RX-
SATA1_RX-
PCIE_RX6-
PCIE_TX6-
21
GND(FIXED)
GND(FIXED)
GND(FIXED)
GND(FIXED)
22
SATA2_TX+
SATA3_TX+
PCIE_RX7+
PCIE_TX7+
23
SATA2_TX-
SATA3_TX-
PCIE_RX7-
PCIE_TX7-
28
COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D)
Controls, LEDs, and Connectors
Table 3-1 COM Express Connector Pin Definition (continued)
Row
A
B
C
D
24
SUS_S5#
PWR_OK
DDI1_HPD
RSVD
25
SATA2_RX+
SATA3_RX+
DDI1_PAIR4+
RSVD
26
SATA2_RX-
SATA3_RX-
DDI1_PAIR4-
DDI1_PAIR0+
27
BATLOW#
WDT
RSVD
DDI1_PAIR0-
28
ATA_ACT#
AC/HDA_SDIN2
RSVD
RSVD
29
AC/HDA_SYNC
AC/HDA_SDIN1
DDI1_PAIR5+
DDI1_PAIR1+
30
AC/HDA_RST#
AC/HDA_SDIN0
DDI1_PAIR5-
DDI1_PAIR1-
31
GND(FIXED)
GND(FIXED)
GND(FIXED)
GND(FIXED)
32
AC/HDA_BITCLK
SPKR
DDI2_AUX+
DDI1_PAIR2+
33
AC/HDA_SDOUT
I2C_CK
DDI2_AUX-
DDI1_PAIR2-
34
BIOS_DISABLE#
I2C_DAT
DDI2_CTRLCLK
DDI2_CTRLDATA
35
THRMTRIP#
THRM#
RSVD
RSVD
36
USB6-
USB7-
DDI3_AUX+
DDI1_PAIR3+
37
USB6+
USB7+
DDI3_AUX-
DDI1_PAIR3-
38
USB_6_7_OC#
USB_4_5_OC#
DDI3_CTRLCLK
DDI3_CTRLDATA
39
USB4-
USB5-
DDI3_PAIR0+
DDI2_PAIR0+
40
USB4+
USB5+
DDI3_PAIR0-
DDI2_PAIR0-
41
GND(FIXED)
GND(FIXED)
GND(FIXED)
GND(FIXED)
42
USB2-
USB3-
DDI3_PAIR0+
DDI2_PAIR1+
43
USB2+
USB3+
DDI3_PAIR0-
DDI2_PAIR1-
44
USB_2_3_OC#
USB_0_1_OC#
DDI3_HPD
DDI2_HPD
45
USB0-
USB1-
RSVD
RSVD
46
USB0+
USB1+
DDI3_PAIR2+
DDI2_PAIR2+
47
VCC_RTC
EXCD1_PERST#
DDI3_PAIR2-
DDI2_PAIR2-
48
EXCD0_PERST#
EXCD1_CPPE#
RSVD
RSVD
49
EXCD0_CPPE#
SYS_RESET#
DDI3_PAIR3+
DDI2_PAIR3+
50
LPC_SERIRQ
CB_RESET#
DDI3_PAIR3-
DDI2_PAIR3-
COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D)
29
Controls, LEDs, and Connectors
Table 3-1 COM Express Connector Pin Definition (continued)
Row
A
B
C
D
51
GND(FIXED)
GND(FIXED)
GND(FIXED)
GND(FIXED)
52
PCIE_TX5+
PCIE_RX5+
PEG_RX0+
PEG_TX0+
53
PCIE_TX5-
PCIE_RX5-
PEG_RX0-
PEG_TX00-
54
GPI0
GPO1
TYPE0#
PEG_LANE_RV#
55
PCIE_TX4+
PCIE_RX4+
PEG_RX1+
PEG_TX1+
56
PCIE_TX4-
PCIE_RX4-
PEG_RX1-
PEG_TX1-
57
GND
GPO2
TYPE1#
TYPE2#
58
PCIE_TX3+
PCIE_RX3+
PEG_RX2+
PEG_TX2+
59
PCIE_TX3-
PCIE_RX3-
PEG_RX2-
PEG_TX2-
60
GND(FIXED)
GND(FIXED)
GND(FIXED)
GND(FIXED)
61
PCIE_TX2+
PCIE_RX2+
PEG_RX3+
PEG_TX3+
62
PCIE_TX2-
PCIE_RX2-
PEG_RX3-
PEG_TX3-
63
GPI1
GPO3
RSVD
RSVD
64
PCIE_TX1+
PCIE_RX1+
RSVD
RSVD
65
PCIE_TX1-
PCIE_RX1-
PEG_RX4+
PEG_TX4+
66
GND
WAKE0#
PEG_RX4-
PEG_TX4-
67
GPI2
WAKE1#
RSVD
GND
68
PCIE_TX0+
PCIE_RX0+
PEG_RX5+
PEG_TX5+
69
PCIE_TX0-
PCIE_RX0-
PEG_RX5-
PEG_TX5-
70
GND(FIXED)
GND(FIXED)
GND(FIXED)
GND(FIXED)
71
LVDS_A0+
LVDS_B0+
PEG_RX6+
PEG_TX6+
72
LVDS_A0-
LVDS_B0-
PEG_RX6-
PEG_TX6-
73
LVDS_A1+
LVDS_B1+
DDI1_CTRLDATA
DDI1_CTRLCLK
74
LVDS_A1-
LVDS_B1-
PEG_RX7+
PEG_TX7+
75
LVDS_A2+
LVDS_B2+
PEG_RX7-
PEG_TX7-
76
LVDS_A2-
LVDS_B2-
GND
GND
77
LVDS_VDD_EN
LVDS_B3+
RSVD
IDE_CBLID#
30
COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D)
Controls, LEDs, and Connectors
Table 3-1 COM Express Connector Pin Definition (continued)
Row
A
B
C
D
78
LVDS_A3+
LVDS_B3-
PEG_RX8+
PEG_TX8+
79
LVDS_A3-
LVDS_BKLT_EN
PEG_RX8-
PEG_TX8-
80
GND(FIXED)
GND(FIXED)
GND(FIXED)
GND(FIXED)
81
LVDS_A_CK+
LVDS_B_CK+
PEG_RX9+
PEG_TX9+
82
LVDS_A_CK-
LVDS_B_CK-
PEG_RX9-
PEG_TX9-
83
LVDS_I2C_CK
LVDS_BKLT_CTRL
RSVD
RSVD
84
LVDS_I2C_DAT
VCC_5V_SBY
GND
GND
85
GPI3
VCC_5V_SBY
PEG_RX10+
PEG_TX10+
86
KBD_RST#
VCC_5V_SBY
PEG_RX10-
PEG_TX10-
87
KBD_A20GATE
VCC_5V_SBY
GND
GND
88
PCIE0_CK_REF+
RSVD
PEG_RX11+
PEG_TX11+
89
PCIE0_CK_REF-
VGA_RED
PEG_RX11-
PEG_TX11-
90
GND(FIXED)
GND(FIXED)
GND(FIXED)
GND(FIXED)
91
SPI_CS0#
VGA_GRN
PEG_RX12+
PEG_TX12+
92
SPI_MISO
VGA_BLU
PEG_RX12-
PEG_TX12-
93
GPO0
VGA_HSYNC
GND
GND
94
SPI_CLK
VGA_VSYNC
PEG_RX13+
PEG_TX13+
95
SPI_MOSI
VGA_I2C_CK
PEG_RX13-
PEG_TX13-
96
GND
VGA_I2C_DAT
GND
GND
97
VCC_12V
RSVD
RSVD
PEG_ENABLE#
98
VCC_12V
RSVD
PEG_RX14+
PEG_TX14+
99
VCC_12V
RSVD
PEG_RX14-
PEG_TX14-
100
GND(FIXED)
GND(FIXED)
GND(FIXED)
GND(FIXED)
101
VCC_12V
VCC_12V
PEG_RX15+
PEG_TX15+
102
VCC_12V
VCC_12V
PEG_RX15-
PEG_TX15-
103
VCC_12V
VCC_12V
GND
GND
104
VCC_12V
VCC_12V
VCC_12V
VCC_12V
COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D)
31
Controls, LEDs, and Connectors
Table 3-1 COM Express Connector Pin Definition (continued)
Row
A
B
C
D
105
VCC_12V
VCC_12V
VCC_12V
VCC_12V
106
VCC_12V
VCC_12V
VCC_12V
VCC_12V
107
VCC_12V
VCC_12V
VCC_12V
VCC_12V
108
VCC_12V
VCC_12V
VCC_12V
VCC_12V
109
VCC_12V
VCC_12V
VCC_12V
VCC_12V
110
GND(FIXED)
GND(FIXED)
GND(FIXED)
GND(FIXED)
3.3
LEDs
Table 3-2 LEDs
32
States
Location
Description
S0
D20
ON: System is full on
S3
D22
ON: System is suspended to memory
S4
D24
ON: System is hybernating
S5
D23
ON: System is off
System PWROK
D21
ON: All system power is OK
Type6 Error
D34
ON: Module does not comply with Type 6
spec
Thermal Trip
D26
ON: CPU is hot; system needs to be shut
down
Suspend Status
D28
ON: Suspend Status
Mini-CD SW OK
D37
ON: USB and PCI-E have both switched to
mini PCI-E slot
COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D)
Controls, LEDs, and Connectors
3.4
Connectors
3.4.1
Video
3.4.1.1
LVDS
Table 3-3 P8, Backlight Wafer Header Pin Definition
Pin
Signal
1
12V
2
BKLT_EN
3
GND
4
BKLT_CTRL
5
5V
Table 3-4 P6, LVDS Connector Pin Definition
Pin
Signal
Pin
Signal
1
LVDSA_DATA0_P
2
LVDSB_DATA0_P
3
LVDSA_DATA0_N
4
LVDSB_DATA0_N
7
LVDSA_DATA1_P
8
LVDSB_DATA1_P
9
LVDSA_DATA1_N
10
LVDSB_DATA1_N
13
LVDSA_DATA2_P
14
LVDSB_DATA2_P
15
LVDSA_DATA2_N
16
LVDSB_DATA2_N
19
LVDSA_DATA3_P
20
LVDSB_DATA3_P
21
LVDSA_DATA3_N
22
LVDSB_DATA3_N
25
LVDSA_CLK_P
26
LVDSB_CLK_P
27
LVDSA_CLK_N
28
LVDSB_CLK_N
31
LVDS_I2C_CLK
32
LVDS_I2C_DATA
COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D)
33
Controls, LEDs, and Connectors
Table 3-4 P6, LVDS Connector Pin Definition (continued)
Pin
Signal
Pin
Signal
33,35,37,39
VDD (3.3V OR 5V)
36,38,40
VDD (12V)
5,
11,17,23,29
GND
6,12,18,24,3
0,34
GND
The 3 V or 5 V DC LVDS power supply is configured through the 3-pin jumper P7.
Table 3-5 P7, LVDS Power Supply Jumper Configuration
Jumper Setting
Configuration
P7 (1-2)
3.3V (Default)
P7 (2-3)
5V
The 12 V DC LVDS power supply is configured through the 3-pin header P35
Table 3-6 P35, LVDS Power Supply Jumper Configuration
3.4.1.2
Jumper Setting
Configuration
P35 (1-2)
12V
P35 (2-3)
NC (Default)
VGA
Table 3-7 J5, VGA Connector Pin Definition
34
Pin
Signal
Pin
Signal
V1
CRT_R
V2
CRT_G
V3
CRT_B
V4
NC
V5
GND
V6
GND
V7
GND
V8
GND
V9
5V
V10
GND
COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D)
Controls, LEDs, and Connectors
Table 3-7 J5, VGA Connector Pin Definition (continued)
3.4.1.3
Pin
Signal
Pin
Signal
V11
NC
V12
DDCDATA
V13
HSYNC
V14
VSYNC
V15
DDCCLK
HDMI
Table 3-8 J5, HDMI Connector Pin Definition
3.4.1.4
Pin
Signal
Pin
Signal
H1
OUT_D2+
H2
GND
H3
OUT_D2-
H4
OUT_D1+
H5
GND
H6
OUT_D1-
H7
OUT_D0+
H8
GND
H9
OUT_D0-
H10
TLC
H11
GND
H12
TLC-
H13
NC
H14
NC
H15
SCL_IN
H16
SDA_IN
H17
GND
H18
5V
H19
HPD_IN
Display Port
Table 3-9 J3 and J4, Display Port Connector Pin Definition
Pin
Signal
1
DP_0_P
3
DP_0_N
COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D)
35
Controls, LEDs, and Connectors
Table 3-9 J3 and J4, Display Port Connector Pin Definition (continued)
3.4.2
Pin
Signal
4
DP_1_P
6
DP_1_N
7
DP_2_P
9
DP_2_N
10
DP_3_P
12
DP_3_N
13
DP_AUX_EN_N
15
DP_AUX_P
17
DP_AUX_N
18
DP_HPD
20
VCC_3
2,5,8,11,14,16,19
GND
Audio
Table 3-10 J16, Audio Jack Connector Pin Definition
36
Pin
Signal
Pin
Signal
A1
LIN_L
A2
LIN_JD
A3
AGND
A4
LIN_R
B1
LOUT_L
B2
LOUT_JD
B3
AGND
B4
LOUT_R
C0
AGND
C1
MIC1L
C2
MIC1_JD
C3
AGND
C4
MIC1R
MH1~MH4
AGND
COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D)
Controls, LEDs, and Connectors
Table 3-11 P11, Audio Header Pin Definition
3.4.3
Pin
Signal
Pin
Signal
1
MIC2_L
2
GND
3
MIC2_R
4
NC
5
LOUT2_R
6
MIC2_JD
7
GND
8
KEY
9
LOUT2_L
10
LOUT2_JD
LAN
Table 3-12 J1, LAN Connector Pin Definition
Pin
Signal
Pin
Signal
1
NC
14
1.8V
2
LAN1_MID3_N
15
LAN2_MID0_P
3
LAN1_MID2_P
16
LAN2_MID1_N
4
GBE0_CTREF
17
1.8V
5
LAN1_MID1_N
18
LAN2_MID2_P
6
LAN1_MID0_P
19
LAN2_MID3_N
7
GBE0_CTREF
20
GND
8
LAN1_MID3_P
21
LAN2_MID0_N
9
GBE0_CTREF
22
1.8V
10
LAN1_MID2_N
23
LAN2_MID1_P
11
LAN1_MID1_P
24
LAN2_MID2_N
12
GBE0_CTREF
25
1.8V
13
LAN1_MID0_N
26
LAN2_MID3_P
31
LAN1_LED_LINK_N
27
LAN2_LED_LINK_N
32
LAN1_LED_LINK_P
28
LAN2_LED_LINK_P
33
LAN1_LED_ACT_N
29
LAN2_LED_ACT_N
COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D)
37
Controls, LEDs, and Connectors
Table 3-12 J1, LAN Connector Pin Definition (continued)
3.4.4
Pin
Signal
Pin
Signal
34
LAN1_LED_ACT_P
30
LAN2_LED_ACT_P
PCI Express
Jumpers P9, P24, and P25 are used to configure PCI Express multiplexed devices.
Table 3-13 P9 Jumper Setting
Jumper Setting
Configuration
P9 (1-2)
x4 PCI-E slot
P9 (2-3)
x1 PCI-E slot (Default)
Table 3-14 P24 Jumper Setting
Jumper Setting
Configuration
P24 (1-2)
x4 PCI-E slot
P24 (2-3)
PCI-E Mini Card (Default)
Table 3-15 P25 Jumper Setting
38
Jumper Setting
Configuration
P25 (1-2)
x4 PCI-E slot
P25 (2-3)
LAN (Default)
COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D)
Controls, LEDs, and Connectors
3.4.5
USB
3.4.5.1
USB 2.0
Table 3-16 P2, USB 2.0 Header Pin Definition
Pin
Signal
Pin
Signal
1
5VDUAL
2
5VDUAL
3
USB1 _N
4
USB2_N
5
USB1_P
6
USB2_P
7
GND
8
GND
9
NC
10
Key
P1, a USB 2.0 header could be used for eUSB flash applications.
Table 3-17 P1, USB 2.0 Header Pin Definition
Pin
Signal
Pin
Signal
1
5VDUAL
2
5VDUAL
3
USB _N
4
NC
5
USB_P
6
NC
7
GND
8
GND
9
NC
10
Key
P39, another USB 2.0 header could be used for PCI Express Mini Card applications.
Table 3-18 P39, USB 2.0 Header Pin Definition
Pin
Signal
Pin
Signal
1
5VDUAL
2
NC
3
USB _N
4
NC
COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D)
39
Controls, LEDs, and Connectors
Table 3-18 P39, USB 2.0 Header Pin Definition (continued)
Pin
Signal
Pin
Signal
5
USB_P
6
NC
7
GND
8
GND
9
NC
10
Key
You need to set a 3-pin jumper (P10) if you want to configure USB multiplexed devices.
Table 3-19 P10, Jumper Settings for Configuring USB Multiplexed Devices
3.4.5.2
Jumper Setting
Configuration
P10 (1-2)
USB 2.0 onboard
P10 (2-3)
Mini Card (Default)
USB 3.0
Table 3-20 J14 and J15, USB 3.0 Connector Pin Definition
40
Pin
Signal
Pin
Signal
1
5V
2
USB_P0 _N
3
USB_P0 _P
4
GND
5
USB0_SSRX _N
6
USB0_SSRX _P
7
GND
8
USB0_SSTX _N
9
USB0_SSTX _P
10
5V
11
USB_P1 _N
12
USB_P1 _P
13
GND
14
USB1_SSRX_N
15
USB1_SSRX _P
16
GND
17
USB1_SSTX _N
18
USB1_SSTX _P
COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D)
Controls, LEDs, and Connectors
3.4.6
Storage
Table 3-21 P10—P13, SATA Socket Pin Definition
Pin
Signal
1
GND
2
SATA_TX_P
3
SATA_TX_N
4
GND
5
SATA_RX_N
6
SATA_RX_P
7
GND
3.4.7
Super I/O
3.4.7.1
Fan
Table 3-22 P3 and P27, Fan Header Pin Definition
Pin
Signal
1
GND
2
12V
3
TACH
4
PWM
COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D)
41
Controls, LEDs, and Connectors
3.4.7.2
PS/2
Table 3-23 P26, PS/2 (Keyboard and Mouse) Connectors Pin Definition
3.4.7.3
Pin
Signal
1
5V
2
KB_DATA
3
KB_CLK
4
MS_DATA
5
MS_CLK
6
GND
LPT Port
Table 3-24 P32, LPT Header Pin Definition
42
Pin
Signal
Pin
Signal
1
STB_N
2
PD0
3
PD1
4
PD2
5
PD3
6
PD4
7
PD5
8
PD6
9
PD7
10
ACK_N
11
BUSY_N
12
PE_N
13
SLCT_N
14
AFD_N
15
ERR_N
16
INIT_N
17
SLIN_N
18—25
GND
26
Key
COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D)
Controls, LEDs, and Connectors
3.4.7.4
Serial Ports
Table 3-25 P18—P23, RS-232 Headers Pin Definition
Pin
Signal
Pin
Signal
1
DCD_N
2
RXD
3
TXD
4
DTR
5
GND
6
DSR_N
7
RTS_N
8
CTS_N
9
RI_N
10
Key
Table 3-26 P37 and P33, RS-422/RS-485 Headers Pin Definition
Pin
Signal
1
RS422_RX_N
2
RS422_RX_P
3
RS422_TX_N/RS485_N
4
RS422_TX_P/RS485_P
You need to set jumpers P34 and P41 to configure the serial ports defined above as RS-232 or
RS-422/485 ports.
Table 3-27 Set Jumpers P34 and P41
Jumper Setting
Configuration
P34/P41 (1-2)
RS232 (Default)
P34/P41 (3-4)
RS422
P34/P41 (5-6)
RS485
COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D)
43
Controls, LEDs, and Connectors
Table 3-28 P40 PS_ON Select Jumper
3.4.8
Jumper Setting
Configuration
P40 (1-2)
Powe on through SIO (Default)
P40 (2-3)
S3 and Type VI
Power
Table 3-29 ATX Power Supply Connector Pin Definition
Pin
Signal
1
GND
2
GND
3
+12V
4
+12V
3.5
Headers
3.5.1
LPC
Table 3-30 P29, Low Pin Count (LPC) Header Pin Definition
44
Pin
Signal
1
CLK_33M
2
AD1
3
RST_N
4
AD0
5
FRAME_N
6
3.3V
COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D)
Controls, LEDs, and Connectors
Table 3-30 P29, Low Pin Count (LPC) Header Pin Definition (continued)
3.5.2
Pin
Signal
7
AD3
8
GND
9
AD2
Trusted Platform Module (TPM)
Table 3-31 P28, Trusted Platform Module (TPM) Header Pin Definition
3.5.3
Pin
Signal
Pin
Signal
1
CLK_33M
2
GND
3
FRAME_N
4
NC
5
RST_N
6
5V
7
AD3
8
AD2
9
3.3V
10
AD1
11
AD0
12
GND
13
SMB_CLK
14
SMB_DATA
15
3VDUAL
16
INT_SERIRQ
17
GND
18
CLKRUN_N
19
3.3V
20
DRQ0_N
GPIO
Table 3-32 P30, GPIO Header Pin Definition
Pin
Signal
1
GPO0
COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D)
45
Controls, LEDs, and Connectors
Table 3-32 P30, GPIO Header Pin Definition (continued)
3.5.4
Pin
Signal
2
GPI0
3
GPO1
4
GPI1
5
GPO2
6
GPI2
7
GPO3
8
GPI3
9
3.3V
10
GND
Miscellaneous I/O
Table 3-33 P16, Miscellaneous I/O Header Pin Definition
46
Pin
Signal
Pin
Signal
1
HD_LED
2
POWER_LED
3
HD_LED#
4
POWER_LED#
5
GND
6
EXT_PWRBTN_N
7
PM_SYSRST_N
8
GND
9
NC
10
Key
COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D)
Controls, LEDs, and Connectors
3.5.5
SPI Flash
Table 3-34 P13, SPI Flash Header Pin Definition
Pin
Signal
1
3.3V DUAL
2
GND
3
SPI_CS_N
4
SF_SPI_CLK
5
SF_SPI_SO
6
SF_SPI_SI
7
NC
8
NC
You must set the jumper defined below if you want to configure how the SPI flash is accessed.
Table 3-35 P12 and P14, Jumper Settings for SPI Flash SF100 header
P12 Jumper Setting
Configuration
P12 (1-2)
To PCH (Default)
P12 (2-3)
To SF100 header
P14 Jumper Setting
Configuration
P14 (1-2)
Enable SPI flash chip U9 and disable U10 (Default)
P14 (2-3)
Enable SPI flash chip U10 and disable U9
Use Jumper P15 to enable or disable the BIOS on the COM Express module
Table 3-36 P15 and P38, Jumper Configuration to Enable/Disable BIOS
P15 Jumper Setting
Configuration
P15 (1-2)
Enable BIOS on the module (Default)
COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D)
47
Controls, LEDs, and Connectors
Table 3-36 P15 and P38, Jumper Configuration to Enable/Disable BIOS (continued)
P15 Jumper Setting
Configuration
P15 (2-3)
Disable BIOS on the module
P38 Jumper Setting
Configuration
P38 (1-2)
Enable CS1 of BIOS on the module (Default)
P38 (2-3)
Disable CS1 of BIOS on the module
Table 3-37 P17 Case Open Select Header
3.5.6
P17 Setting
Configuration
P17 (1-2)
Disable the case open select header (Default)
P17 (2-3)
Enable the case open select header
EEPROM
Table 3-38 P31, EEPROM Header Pin Definition
48
Pin
Signal
1
I2C_CLK
2
I2C_DATA
3
GND
COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D)
Chapter 4
Functional Description
4.1
Block Diagram
Figure 4-1
4.2
COM Express Type 6 Block Diagram
Video
The COMX-CAR-610 supports dual-independent displays using the Mobile Intel processor
Integrated Graphics Controller. This carrier supports following graphic interfaces:
COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D)
49
Functional Description
4.2.1
LVDS
The graphic controller supports up to 24-bit colors per pixel so the COMX-CAR-610 could
support 24-bit LCD panels using different cables.
The board provides an LVDS and backlight header. The LVDS header is a 40 pin, dual-row
header, while the backlight is a 5 pin wafer header.
For information on pin assignments, Table 3-4 on page 33
4.2.2
VGA
The carrier board supports VGA output from the COM Express connector. The VGA signals
come from the same connector as the HDMI signals.
For information on pin assignments, Table 3-7 on page 34.
4.2.3
HDMI
The COMX-CAR-610 supports an HDMI interface from DDI1 of the COM Express connector.
For information on pin assignments, Table 3-8 on page 35.
4.2.4
Display Port
The COMX-CAR-610 supports two Display Ports from DDI2 and DDI3 of the COM Express
connector.
For information on pin assignments, see Table 3-9 on page 35.
4.3
Audio
The COMX-CAR-610 supports line output, microphone output, and line input using industry
standard 3.5 mm mini-jack connectors. The board also provides a two-channel HD audio as
part of the integrated High-Definition Multimedia Interface (HDMI). The integrated HDMI
requires a 1.5 V CODEC.
For information on pin assignments, see Table 3-10 on page 36 and Table 3-11 on page 37.
50
COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D)
Functional Description
4.4
LAN
There are two Gigabit Ethernet ports: one is routed from the COM Express connector, and the
other from WG82574L. The RJ-45 connectors are located on the board and both support
100/1000 Base T.
The LAN connectors have two integrated LEDs. When the green LED is OFF, it indicates that
LAN link is not established. When it is ON, it indicates that a LAN link is established. When it
"blinks," it indicates LAN link activity. A second green LED shall BLINK indicating the activity
state of 100Mbps or 1000Mbps LAN.
For information on pin assignments, see Table 3-12 on page 37.
4.5
PCI Express
The board has one x1 PCI-E slot and and one x16 PCI-E slot. The x16 PCI-E slot can be used for
PCI Express Graphics (PEG). There are also two x4 PCI-E slots. One of the x4 slots can be used
for other applications by using PCI-E multiplexer devices.
For information on pin assignments, see Table 3-13 on page 38.
Figure 4-2
PCI Express Block Diagram
COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D)
51
Functional Description
4.5.1
PCI Express Mini Card
The carrier board comes with a PCI Express Mini Card connector that supports the Intel
WiMAX/WiFi Link 5050 and Intel WiFi Link 5000 series of wireless devices. The connector
conforms to PCI Express Mini Card Electromechanical Specification 1.1, implementing both
PCI Express and USB interfaces. The PCI-E Mini Card is available only when the related PCI-E
MUX and USB MUX are both set appropriately.
Figure 4-3
4.6
PCI Express Mini Card Setting
USB
The are four USB 2.0 ports on the board. Two of them could be used for other applications: one
for external USB flash, and the other for a PCI-E Mini Card through a USB MUX device. All USB
2.0 ports support low-speed, full-speed, and high-speed transfer rates using the USB 2.0
Enhanced Host Controller Interface (EHCI).
There are also four USB 3.0 ports from COM Express connector. The USB 3.0 ports support lowspeed, full-speed, and high-speed transfer rates using the USB 3.0 Enhanced Host Controller
Interface (EHCI).
For information on pin assignments, see Table 3-20 on page 40.
4.7
Storage
There are four SATA sockets on the carrier board for connecting to internal SATA 2.0 devices.
52
COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D)
Functional Description
For information on pin assignments, see Table 3-21 on page 41.
4.8
Super I/O
The COMX-CAR-610 provides a Super I/O for extending several function modules.
For information on pin assignments, see Super I/O on page 41.
Figure 4-4
4.8.1
Super I/O Block Diagram
Voltage and Thermal Monitoring
The COMX-CAR-610 provides voltage monitoring capabilities on 3 V, 5 V, and 12 V rails, and
also provides thermal monitoring capabilities for the COM Express module and its
environment. Voltage and thermal values are read by the management engine, and alerts are
reported to the management engine.
COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D)
53
Functional Description
4.8.2
Fan Control
There are two 4-wire fan headers on the COMX-CAR-610 for module fan and system fan. Fans
support fan TACH input and PWM fan speed control. The board uses a 4-pin locking connector
equivalent to Molex 47053-1000.
For information on pin assignments, see Table 3-22 on page 41.
4.8.3
PS/2
There is a 6-pin wafer PS/2 header for keyboard and mouse.
For information on pin assignments, see Table 3-23 on page 42.
4.8.4
LPT
There is a 2 x 13 pin header for the LPT interface on the COMX-CAR-610.
For information on pin assignments, see Table 3-24 on page 42.
4.8.5
RS-232 and RS-422/485 Ports
The COMX-CAR-610 implements up to six RS-232 ports, two of which can be switched to RS422 or RS-485 ports by setting two jumpers on the 2 x 3 pin header. All the RS-232 ports are
implemented as 2 x 5 pin, dual-row headers, and the RS-422/485 ports as 1 x 4 pin, single-row
headers.
Two of the six COM ports from the Super I/O can be configured as RS-232 ports, or as RS-422
or RS-485 ports by setting a 6-pin, dual-row jumper.
For information on pin assignments, see Table 3-25 on page 43 and Table 3-26 on page 43.
54
COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D)
Functional Description
4.9
SPI Flash
There are two SPI flash chips. Each chip has a capacity of 4 MB for BIOS, Gigabit Ethernet, and
ME.
Figure 4-5
SPI Flash Block Diagram
The flash chips can be accessed either by the PCH or external devices with SPI interface through
a 2 x 4 pin SF100 header.
A 3-pin jumper (P12) is supplied to configure how SPI flash is accessed, and when the SPI flash
is set to be accessed by external devices through the SF100 header. Each of the SPI flash chips
can be enabled or disabled by setting a 3-pin jumper (P14). For information on pin
assignments, see Table 3-35 on page 47.
The COMX-CAR-610 also provides two 3-pin jumpers (P15 and P38) to determine whether
enable or disable the BIOS on the module. For information on pin assignments, see Table 3-36
on page 47.
COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D)
55
Functional Description
4.10
Watchdog Timer
The COMX-CAR-610 provides a watchdog timer (WDT), which is a combination of two
watchdog timers coming from COM Express connector and Super I/O.
Figure 4-6
Watchdog Timer Block Diagram
A valid WDT output signal resets the COMX-CAR-610. The BIOS disables the device at boot
(software is enabled when the watchdog application loads). The WDT is disabled before
entering S3 state, and re-enabled upon exiting S3.
4.11
Real Time Clock (RTC)
There is an onboard SMT battery holder. The battery holder allows for the quick and easy
replacement of a 3 V button cell lithium battery which provides backup power to the onboard
RTC.
The RTC supports two lockable memory ranges. By setting bits in the configuration space, two
8-byte ranges can be locked to read and write accesses. This prevents unauthorized reading of
passwords or other system security information.
56
COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D)
Functional Description
The RTC also supports a data alarm that allows for scheduling a wake up event up to 30 days in
advance rather than just 24 hours in advance.
4.12
Wake Events
The COMX-CAR-610 awakes from sleep states S3 and S4 when one of the following conditions
occur:
Table 4-1 Wake Events
Wake Events
Description
PCI Express
Through PE_WAKE_N
LAN
The management engine supports Wake-on-LAN (WOL) using
wired LAN.
USB
-
Power button
If the power button is pressed for more than four seconds, it causes
an unconditional transition to the S5 state.
COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D)
57
Functional Description
58
COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D)
Appendix A
A
Related Documentation
A.1
Emerson Network Power—Embedded Computing
Documents
The publications listed below are referenced in this manual. You can obtain electronic copies of
Emerson Network Power, Embedded Computing publications by contacting your local
Emerson sales office. For released products, you can also visit our Web site for the latest copies
of our product documentation.
1. Go to www.emersonnetworkpower.com/embeddedcomputing.
2. Under Resources, click Technical Documentation.
3. Enter the manual you are looking for in the search field. Use either the publication number
or the complete name of the product to search for available manuals.
Table A-1 Emerson Network Power, Embedded Computing Publications
A.2
Document Title
Publication Number
COMX-CAR-610 COM Express Carrier Board Quick Start Guide
6806800A13
COMX-CAR-610 COM Express Carrier Board Release Notes
TBD
COMX-CAR-610 COM Express Carrier Board Safety Notes
6806800A12
COMX-CAR-610 Installation and Use
6806800K26
COMX-CAR-610 Quick Start Guide
6806800K27
COMX-CAR-610 Safety Notes
6806800K28
Manufacturers’ Documents
You can also get additional information from manufacturers’ documentation. Note that the
information in these documents are subject to change without prior notice.
COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D)
59
Related Documentation
60
COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D)
Safety Notes
This section provides warnings that precede potentially dangerous procedures throughout
this manual. Instructions contained in the warnings must be followed during all phases of
operation, service, and repair of this equipment. You should also employ all other safety
precautions necessary for the operation of the equipment in your operating environment.
Failure to comply with these precautions or with specific warnings elsewhere in this manual
could result in personal injury or damage to the equipment.
Emerson intends to provide all necessary information to install and handle the product in this
manual. Because of the complexity of this product and its various uses, we do not guarantee
that the given information is complete. If you need additional information, ask your Emerson
representative.
The product has been designed to meet the standard industrial safety requirements. It must
only be used in its specific area of office telecommunication industry, industrial control, and
development. It must not be used in safety critical components, life supporting devices or on
aircraft.
Only personnel trained by Emerson or persons qualified in electronics or electrical engineering
are authorized to install, remove or maintain the product. The information given in this manual
is meant to complete the knowledge of a specialist and must not be used as replacement for
qualified personnel.
Keep away from live circuits inside the equipment. Operating personnel must not remove
equipment covers. Only factory authorized service personnel or other qualified service
personnel is allowed to remove equipment covers for internal subassembly or component
replacement or any internal adjustment.
Do not install substitute parts or perform any unauthorized modification of the equipment or
the warranty may be voided. Contact your local Emerson representative for service and repair
to make sure that all safety features are maintained.
Emerson and our suppliers take significant steps to make sure that there are no bent pins on
the backplane or connector damage to the boards prior to leaving the factory. Bent pins
caused by improper installation or by inserting boards with damaged connectors could void
the Emerson warranty for the backplane or boards.
This product operates with dangerous voltages that can cause injury or death. Use extreme
caution when handling, testing, and adjusting this equipment and its components.
COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D)
61
Safety Notes
EMC
FCC Class A
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules, EN55022. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, can cause
harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which
case the user is required to correct the interference at his own expense.
Use only shielded cables when connecting peripherals to assure that appropriate radio
frequency emissions compliance is maintained. Installed blades must have the face plates
installed and all vacant slots in the shelf must be covered.
62
COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D)
Safety Notes
For applications where this product is provided without a face plate, or where the face plate has
been removed, your system chassis/enclosure must provide the required electromagnetic
interference (EMI) shielding to maintain EMC compliance.
Board products are tested in a representative system to show compliance with the above
mentioned requirements. A proper installation in a compliant system maintains the required
performance.
As soon as you modify the product or change the default configuration you are responsible for
complying with all relevant regulatory standards.
VCCI
This is a Class A product based on the standard of the Voluntary Control Council for
Interference by Information Technology Interference (VCCI). If this equipment is used in a
domestic environment, radio disturbance can arise. When such trouble occurs, the user is
required to take corrective actions.
Installation
Damage of Circuits
Electrostatic discharge and incorrect installation and removal of the product can damage
circuits or shorten their life.
Before touching the product make sure that your are working in an ESD-safe environment or
wear an ESD wrist strap or ESD shoes. Hold the product by its edges and do not touch any
components or circuits.
COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D)
63
Safety Notes
Operation
Product Damage
High humidity and condensation on surfaces cause short circuits.
Do not operate the product outside the specified environmental limits. Make sure the product
is completely dry and there is no moisture on any surface before applying power.
Battery
Data Loss
Installing another battery type than the one that is mounted at product delivery may cause
data loss since other battery types may be specified for other environments or may have a
shorter lifetime.
Only use the same type of lithium battery as is already installed.
PCB and Battery Holder Damage
Removing the battery with a screw driver may damage the PCB or the battery holder.
Do not use a screw driver to remove the battery from its holder.
Product Damage
Incorrect replacement of lithium batteries can result in a hazardous explosion.
When exchanging the on-board lithium battery, make sure that the new and the old battery
are exactly the same battery models.
If the respective battery model is not available, contact your local Emerson sales
representative for the availability of alternative officially approved battery models.
Environment
Environmental Damage
Improperly disposing of used products may harm the environment.
Always dispose of used products according to your country’s legislation and manufacturer’s
instructions.
64
COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D)
Sicherheitshinweise
Dieses Kapitel enthält Hinweise, die potentiell gefährlichen Prozeduren innerhalb dieses
Handbuchs vorrangestellt sind. Beachten Sie unbedingt in allen Phasen des Betriebs, der
Wartung und der Reparatur des Systems die Anweisungen, die diesen Hinweisen enthalten
sind. Sie sollten außerdem alle anderen Vorsichtsmaßnahmen treffen, die für den Betrieb des
Systems innerhalb Ihrer Betriebsumgebung notwendig sind. Wenn Sie diese
Vorsichtsmaßnahmen oder Sicherheitshinweise, die an anderer Stelle diese Handbuchs
enthalten sind, nicht beachten, kann das Verletzungen oder Schäden am System zur Folge
haben.
Emerson ist darauf bedacht, alle notwendigen Informationen zum Einbau und zum Umgang
mit dem System in diesem Handbuch bereit zu stellen. Da es sich jedoch bei dem System um
ein komplexes Produkt mit vielfältigen Einsatzmöglichkeiten handelt, können wir die
Vollständigkeit der im Handbuch enthaltenen Informationen nicht garantieren. Falls Sie
weitere Informationen benötigen sollten, wenden Sie sich bitte an die für Sie zuständige
Geschäftsstelle von Emerson.
Das Produkt erfüllt die für die Industrie geforderten Sicherheitsvorschriften und darf
ausschließlich für Anwendungen in der Telekommunikationsindustrie, im Zusammenhang mit
Industriesteuerungen und in der Entwicklung verwendet werden. Es darf nicht in
sicherheitskritischen Anwendungen, lebenserhaltenden Geräten oder in Flugzeugen
verwendet werden.
Einbau, Wartung und Betrieb dürfen nur von durch Emerson ausgebildetem oder im Bereich
Elektronik oder Elektrotechnik qualifiziertem Personal durchgeführt werden. Die in diesem
Handbuch enthaltenen Informationen dienen ausschließlich dazu, das Wissen von
Fachpersonal zu ergänzen, können dieses jedoch nicht ersetzen.
Halten Sie sich von stromführenden Leitungen innerhalb des Systems fern. Entfernen Sie auf
keinen Fall die Systemabdeckung. Nur werksseitig zugelassenes Wartungspersonal oder
anderweitig qualifiziertes Wartungspersonal darf die Systemabdeckung entfernen, um
Systemkomponenten zu ersetzen oder andere Anpassungen vorzunehmen.
Installieren Sie keine Ersatzteile oder führen Sie keine unerlaubten Veränderungen am System
durch, sonst verfällt die Garantie. Wenden Sie sich für Wartung oder Reparatur bitte an die für
Sie zuständige Geschäftsstelle von Emerson. So stellen Sie sicher, dass alle
sicherheitsrelevanten Aspekte beachtet werden.
COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D)
65
Sicherheitshinweise
Emerson und unsere Zulieferer unternehmen größte Anstrengungen um sicherzustellen, dass
sich Pins und Stecker von Boards vor dem Verlassen der Produktionsstätte in einwandfreiem
Zustand befinden. Verbogene Pins, verursacht durch fehlerhafte Installation oder durch
Installation von Boards mit beschädigten Steckern kann die durch Emerson gewährte Garantie
für Boards und Backplanes erlöschen lassen.
Dieses Produkt wird mit gefährlichen Spannungen betrieben, die zu Verletzungen und Tod
führen können. Seien Sie im Umgang mit dem Produkt und beim Testen und Anpassen des
Produktes und seiner Komponenten äußerst vorsichtig.
EMV
FCC Class A
Das Produkt wurde getestet und erfüllt die für digitale Geräte der Klasse A gültigen Grenzwerte
gemäß den FCC-Richtlinien Abschnitt 15 bzw. EN 55022 Klasse A. Diese Grenzwerte sollen
einen angemessenen Schutz vor Störstrahlung beim Betrieb des Produkts in Geschäfts-,
Gewerbe- sowie Industriebereichen gewährleisten. Das Produkt arbeitet im
Hochfrequenzbereich und erzeugt Störstrahlung. Bei unsachgemäßem Einbau und anderem
als in diesem Handbuch beschriebenen Betrieb können Störungen im Hochfrequenzbereich
auftreten.
Diese Einrichtung kann im Wohnbereich Funkstörungen verursachen; in diesem Fall kann vom
Betreiber verlangt werden, angemessene Maßnahmen durchzuführen und dafür
aufzukommen.
Benutzen Sie zum Anschließen von Peripheriegeräten ausschließlich abgeschirmte Kabel. So
stellen Sie sicher, dass ausreichend Schutz vor Störstrahlung vorhanden ist. Die Blades müssen
mit der Frontblende installiert und alle freien Steckplätze müssen mit Blindblenden abgedeckt
sein.
Änderungen, die nicht ausdrücklich von Emerson erlaubt sind, können Ihr Recht das System zu
betreiben zunichte machen.
66
COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D)
Sicherheitshinweise
Wenn dieses Produkt ohne Frontblende ausgeliefert wird oder wenn die Frontblende entfernt
wird, muss Ihr System die notwendigenSchutzmechnismen gegen elektromagnetische
interferenzen bereitstellen, um die Einhaltung der eletromagnetischen Verträglichkeit des
Systems zu gewährleisten.
Boardprodukte werden in einem repräsentativen System getestet, um zu zeigen, dass das
Board den oben aufgeführten EMV-Richtlinien entspricht. Eine ordnungsgemäße Installation
in einem System, welches die EMV-Richtlinien erfüllt, stellt sicher, dass das Produkt gemäß den
EMV-Richtlinien betrieben wird.
Sobald Sie das Produkt oder seine Standardkonfiguration verändern, müssen Sie dafür sorgen,
dass alle relevanten Richtlinien eingehalten werden.
VCCI
Das Produkt ist eine Einrichtung der Klasse A gemäß dem Standard des Voluntary Control
Council for Interference von Information Technology Interference (VCCI). Wird das Produkt in
Wohngegenden betrieben, können Störungen im Hochfrequenzbereich auftreten. In einem
solchen Fall ist der Benutzer verpflichtet, entsprechende Gegenmaßnahmen zu ergreifen.
System Installation
Beschädigung von Schaltkreisen
Elektrostatische Entladung und unsachgemäßer Ein- und Ausbau des Produktes kann
Schaltkreise beschädigen oder ihre Lebensdauer verkürzen.
Bevor Sie das Produkt oder elektronische Komponenten berühren, vergewissern Sie sich, daß
Sie in einem ESD-geschützten Bereich arbeiten.
COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D)
67
Sicherheitshinweise
Betrieb
Beschädigung des Systems
Hohe Luftfeuchtigkeit und Kondensat auf den Oberflächen der Produkte kann zu
Kurzschlüssen führen.
Betreiben Sie die Produkte nur innerhalb der angegebenen Grenzwerte für die relative
Luftfeuchtigkeit und Temperatur und stellen Sie vor dem Einschalten des Stroms sicher, dass
sich auf den Produkten kein Kondensat befindet.
Batterie
Datenverlust
Wenn Sie einen anderen Batterietyp installieren als der, der bei Auslieferung des Produktes
installiert war, kann Datenverlust die Folge sein, da die neu installierte Batterie für andere
Umgebungsbedingungen oder eine andere Lebenszeit ausgelegt sein könnte.
Verwenden Sie daher den gleichen Batterietyp, der bei Auslieferung des Produktes installiert
war.
Beschädigung des PCBs und der Batteriehalterung
Wenn Sie die Batterie mit einem Schraubendreher ausbauen, können das PCB und die
Batteriehalterung beschädigt werden.
Benutzen Sie keinesfalls einen Schraubendreher, um die Batterie aus der Halterung zu nehmen.
Beschädigung des Produktes
Fehlerhafter Austausch von Lithium-Batterien kann zu gefährlichen Explosionen führen.
Wenn SIe die Lithium-Batterie auf dem Produkt austauschen, stellen Sie sicher, dass die alte
und die neue Batterie vom gleichen Typ sind.
Ist der Batterietyp nicht verfügbar, wenden Sie sich an Emerson um herauszufinden, welcher
Batterietyp offiziell alternativ verwendet werden darf.
68
COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D)
Sicherheitshinweise
Umweltschutz
Umweltverschmutzung
Falsche Entsorgung der Produkte schadet der Umwelt.
Entsorgen Sie alte Produkte gemäß der in Ihrem Land gültigen Gesetzgebung und den
Empfehlungen des Herstellers.
COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D)
69
Sicherheitshinweise
70
COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D)
Index
A
abbreviations 11
B
block diagram
carrier board type 6 49
box contents 23
C
conventions 13
E
environmental requirements 21
I
Installation
Module 24
installing
COM Express module 24
installing COM Express module 24
P
power requirements 22
R
removing
COM Express module 24
onboard battery 26
removing COM Express module 24
removing onboard battery 26
requirements
environmental 21
power 22
S
shipment contents 23
COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D)
71
Index
72
COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D)
HOW TO REACH LITERATURE AND TECHNICAL SUPPORT:
For literature, training, and technical assistance and support programs, visit
www.emersonnetworkpower.com/embeddedcomputing
Emerson Network Power.
The global leader in enabling Business-Critical Continuity™
AC Power Systems
Connectivity
DC Power Systems
Embedded Computing
Embedded Power
Integrated Cabinet Solutions
www.emersonnetworkpower.com/embeddedcomputing
Outside Plant
Power Switching & Control
Precision Cooling
Services
Site Monitoring
Surge & Signal Protection
Emerson, Business-Critical Continuity, Emerson Network Power and the Emerson Network Power logo are trademarks and service marks of Emerson Electric Co.
All other product or service names are the property of their respective owners.
© 2011 Emerson Electric Co.