Delta 23-700 Instruction manual

Add to my manuals
16 Pages

advertisement

Delta 23-700 Instruction manual | Manualzz

Universal Wet/Dry Grinder

(Model 23-700)

PART NO. 1340208 - 06-06-05

Copyright © 2005 Delta Machinery

To learn more about DELTA MACHINERY visit our website at: www.deltamachinery.com.

For Parts, Service, Warranty or other Assistance, please call

1-800-223-7278 (

In Canada call

1-800-463-3582).

TABLE OF CONTENTS

IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

SAFETY GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

GENERAL SAFETY RULES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

ADDITIONAL SPECIFIC SAFETY RULES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

FUNCTIONAL DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

CARTON CONTENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

SERVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

SERVICE CENTER LOCATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .back cover

IMPORTANT SAFETY INSTRUCTIONS

Read and understand all warnings and operating instructions before using any tool or equipment. When using tools or equipment, basic safety precautions should always be followed to reduce the risk of personal injury.

Improper operation, maintenance or modification of tools or equipment could result in serious injury and property damage. There are certain applications for which tools and equipment are designed. Delta Machinery strongly recommends that this product NOT be modified and/or used for any application other than for which it was designed.

If you have any questions relative to its application DO NOT use the product until you have written Delta Machinery and we have advised you.

Online contact form at www.deltamachinery.com

Postal Mail: Technical Service Manager

Delta Machinery

4825 Highway 45 North

Jackson, TN 38305

(IN CANADA: 125 Mural St. Suite 300, Richmond Hill, ON, L4B 1M4)

Information regarding the safe and proper operation of this tool is available from the following sources:

Power Tool Institute

1300 Sumner Avenue, Cleveland, OH 44115-2851 www.powertoolinstitute.org

National Safety Council

1121 Spring Lake Drive, Itasca, IL 60143-3201

American National Standards Institute, 25 West 43rd Street, 4 floor, New York, NY 10036 www.ansi.org

ANSI 01.1Safety Requirements for Woodworking Machines, and the U.S. Department of Labor regulations www.osha.gov

SAVE THESE INSTRUCTIONS!

2

SAFETY GUIDELINES - DEFINITIONS

It is important for you to read and understand this manual. The information it contains relates to protecting

YOUR SAFETY and PREVENTING PROBLEMS. The symbols below are used to help you recognize this information.

Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.

Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.

Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.

Used without the safety alert symbol indicates potentially hazardous situation which, if not avoided, may result in property damage.

CALIFORNIA PROPOSITION 65

SOME DUST CREATED BY POWER SANDING, SAWING, GRINDING, DRILLING, AND OTHER

CONSTRUCTION ACTIVITIES contains chemicals known to cause cancer, birth defects or other reproductive harm.

Some examples of these chemicals are:

· lead from lead-based paints,

· crystalline silica from bricks and cement and other masonry products, and

· arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, always wear NIOSH/OSHA approved, properly fitting face mask or respirator when using such tools.

3

GENERAL SAFETY RULES

READ AND UNDERSTAND ALL WARNINGS AND OPERATING INSTRUCTIONS BEFORE

USING THIS EQUIPMENT. Failure to follow all instructions listed below, may result in electric shock, fire, and/or serious personal injury or property damage.

IMPORTANT SAFETY INSTRUCTIONS

1.

FOR YOUR OWN SAFETY, READ THE INSTRUCTION

MANUAL BEFORE OPERATING THE MACHINE. Learning the machine’s application, limitations, and specific hazards will greatly minimize the possibility of accidents and injury.

2.

WEAR EYE AND HEARING PROTECTION. ALWAYS

USE SAFETY GLASSES. Everyday eyeglasses are NOT safety glasses. USE CERTIFIED SAFETY EQUIPMENT.

Eye protection equipment should comply with ANSI Z87.1

standards. Hearing equipment should comply with ANSI

S3.19 standards.

3.

WEAR PROPER APPAREL. Do not wear loose clothing, gloves, neckties, rings, bracelets, or other jewelry which may get caught in moving parts. Nonslip footwear is recommended. Wear protective hair covering to contain long hair.

4.

DO NOT USE THE MACHINE IN A DANGEROUS

ENVIRONMENT. The use of power tools in damp or wet locations or in rain can cause shock or electrocution. Keep your work area well-lit to prevent tripping or placing arms, hands, and fingers in danger.

5.

MAINTAIN ALL TOOLS AND MACHINES IN PEAK

CONDITION. Keep tools sharp and clean for best and safest performance. Follow instructions for lubricating and changing accessories. Poorly maintained tools and machines can further damage the tool or machine and/or cause injury.

6.

CHECK FOR DAMAGED PARTS. Before using the machine, check for any damaged parts. Check for alignment of moving parts, binding of moving parts, breakage of parts, and any other conditions that may affect its operation. A guard or any other part that is damaged should be

properly repaired or replaced. Damaged parts can cause further damage to the machine and/or injury.

7.

KEEP THE WORK AREA CLEAN. Cluttered areas and benches invite accidents.

8.

KEEP CHILDREN AND VISITORS AWAY. Your shop is a potentially dangerous environment. Children and visitors can be injured.

9.

REDUCE THE RISK OF UNINTENTIONAL STARTING. Make sure that the switch is in the “OFF” position before plugging in the power cord. In the event of a power failure, move the switch to the “OFF” position. An accidental start-up can cause injury.

10. USE THE GUARDS. Check to see that all guards are in place, secured, and working correctly to reduce the risk of injury.

11. REMOVE ADJUSTING KEYS AND WRENCHES

BEFORE STARTING THE MACHINE. Tools, scrap pieces, and other debris can be thrown at high speed, causing injury.

12. USE THE RIGHT MACHINE. Don’t force a machine or an attachment to do a job for which it was not designed.

Damage to the machine and/or injury may result.

13. USE RECOMMENDED ACCESSORIES. The use of accessories and attachments not recommended by Delta may cause damage to the machine or injury to the user.

14. USE THE PROPER EXTENSION CORD. Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage, resulting in loss of power and overheating. See the Extension Cord Chart for the correct size depending on the cord length and nameplate ampere rating. If in doubt, use the next heavier gauge. The smaller the gauge number, the heavier the cord.

15. SECURE THE WORKPIECE. Use clamps or a vise to hold the workpiece when practical. Loss of control of a workpiece can cause injury.

16. FEED THE WORKPIECE AGAINST THE DIRECTION OF THE

ROTATION OF THE BLADE, CUTTER, OR ABRASIVE

SURFACE. Feeding it from the other direction will cause the workpiece to be thrown out at high speed.

17. DON’T FORCE THE WORKPIECE ON THE MACHINE.

Damage to the machine and/or injury may result.

18. DON’T OVERREACH. Loss of balance can make you fall into a working machine, causing injury.

19. NEVER STAND ON THE MACHINE. Injury could occur if the tool tips, or if you accidentally contact the cutting tool.

20. NEVER LEAVE THE MACHINE RUNNING UNATTENDED.

TURN THE POWER OFF. Don’t leave the machine until it comes to a complete stop. A child or visitor could be injured.

21. TURN THE MACHINE “OFF”, AND DISCONNECT THE

MACHINE FROM THE POWER SOURCE before installing or removing accessories, before adjusting or changing setups, or when making repairs. An accidental start-up can cause injury.

22. MAKE YOUR WORKSHOP CHILDPROOF WITH

PADLOCKS, MASTER SWITCHES, OR BY REMOVING

STARTER KEYS. The accidental start-up of a machine by a child or visitor could cause injury.

23. STAY ALERT, WATCH WHAT YOU ARE DOING, AND

USE COMMON SENSE. DO NOT USE THE MACHINE

WHEN YOU ARE TIRED OR UNDER THE INFLUENCE

OF DRUGS, ALCOHOL, OR MEDICAT-ION. A moment of inattention while operating power tools may result in injury.

24.

USE OF THIS TOOL CAN GENERATE AND

DISBURSE DUST OR OTHER AIRBORNE PARTICLES,

INCLUDING WOOD DUST, CRYSTALLINE SILICA DUST

AND ASBESTOS DUST. Direct particles away from face and body. Always operate tool in well ventilated area and provide for proper dust removal. Use dust collection system wherever possible. Exposure to the dust may cause serious and permanent respiratory or other injury, including silicosis (a serious lung disease), cancer, and death. Avoid breathing the dust, and avoid prolonged contact with dust. Allowing dust to get into your mouth or eyes, or lay on your skin may promote absorption of harmful material. Always use properly fitting

NIOSH/OSHA approved respiratory protection appropriate for the dust exposure, and wash exposed areas with soap and water.

4

ADDITIONAL SPECIFIC SAFETY RULES

FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS PERSONAL INJURY.

1.

DO NOT OPERATE THIS MACHINE until it is completely assembled and installed according to the instructions. A machine incorrectly assembled can cause serious injury.

2.

OBTAIN ADVICE from your supervisor, instructor, or another qualified person if you are not thoroughly familiar with the operation of this machine. Knowledge is safety.

3.

FOLLOW ALL WIRING CODES and recommended electrical connections to prevent shock or electrocution.

4.

ALWAYS USE THE PROVIDED BLOTTER AND

WHEEL FLANGES to mount the grinding wheels on the grinder shaft to prevent wheel damage or accidental separation. Separation can result in fragments flying off the wheel at high speeds.

5.

USE ONLY WHEELS suitable for the speed of the machine. Unsuitable grinding wheels can come apart, throwing fragments out at high speeds.

6.

USE ONLY WHEELS that have a bore exactly equal to the arbors of the machine. Never attempt to machine an undersized wheel to fit an arbor.

Unsuitable grinding wheels can come apart, throwing fragments out at high speeds.

7.

DO NOT OVERTIGHTEN WHEEL NUT.

8.

DO NOT USE A WHEEL THAT VIBRATES. Dress the grinding wheel, replace it, or replace the bearings of the shaft. Unsuitable grinding wheels can come apart, throwing fragments at high speeds.

9.

INSPECT WHEELS before starting the machine for cracks or fragments. REPLACE DAMAGED WHEELS immediately. Parts of the wheel can be thrown at high speeds causing serious injury.

10.

ADJUST EYE SHIELDS close to the grinding wheel, and re-adjust as the wheel wears down. Flying sparks are dangerous and can cause fires or explosions.

11.

ALWAYS MAKE SURE the eye shields are in place, properly adjusted, and secured.

12.

ADJUST TOOL RESTS close to the grinding wheel

(1/8" separation or less). Tighten the tool rest securely to prevent shifting positions, and re-adjust as the wheel wears down. The workpiece can be drawn into the wheel, causing damage to the workpiece and/or serious injury.

13.

STAND TO ONE SIDE before turning the machine

“ON”. Loose fragments or wheel parts could fly from the wheel at high speeds.

14.

NEVER GRIND ON A COLD WHEEL. Run the grinder for one full minute before applying the workpiece. A cold wheel has a tendency to chip. Those fragments could fly from the wheel at high speeds.

15.

NEVER START THE MACHINE with the workpiece against the grinding wheel. The workpiece can be drawn into the wheel, causing damage to the machine and/or serious injury.

16.

CLEAN THE MACHINE thoroughly when processing different types of workpieces (wood, steel, or aluminum). Combining wood and metal dust can create an explosion or fire hazard. DO NOT GRIND

OR POLISH MAGNESIUM. Fire will result.

17.

NEVER GRIND NEAR FLAMMABLE GAS OR

LIQUIDS. Sparks can create a fire or an explosion.

18.

AVOID AWKWARD OPERATIONS AND HAND

POSITIONS. A sudden slip could cause a hand to move into the grinding wheel.

19.

KEEP ARMS, HANDS, AND FINGERS away from the wheel. The abrasive surfaces can cause serious injury.

20.

HOLD THE WORKPIECE FIRMLY against the tool rest. Loss of control of the workpiece can cause serious injury.

21.

DRESS THE WHEEL on the face only. Dressing the side of the wheel could cause it to become too thin for safe use.

22.

GRIND A WORKPIECE using the face of the grinding wheel only. Loss of control of the workpiece can cause serious injury.

23.

NEVER APPLY COOLANT directly to the grinding wheel. Coolant can weaken the bonding strength of the grinding wheel and cause it to fail. Dip the workpiece in water to cool it.

24.

DO NOT TOUCH the ground portion of a workpiece until it has cooled sufficiently. Grinding creates heat.

25.

PROPERLY SUPPORT LONG OR WIDE WORK-

PIECES. Loss of control of the workpiece can cause serious injury.

26.

NEVER PERFORM LAYOUT, ASSEMBLY, or set-up work on the table/work area when the machine is running.

A sudden slip could cause a hand to move into the wheel. Severe injury can result.

27.

TURN THE MACHINE “OFF”, disconnect the machine from the power source, and clean the table/work area before leaving the machine. LOCK

THE SWITCH IN THE “OFF” POSITION to prevent unauthorized use. Someone else might accidentally start the machine and cause serious injury to themselves.

28.

ADDITIONAL INFORMATION regarding the safe and proper operation of power tools (i.e. a safety video) is available from the Power Tool Institute, 1300

Sumner Avenue, Cleveland, OH 44115-2851

(www.powertoolinstitute.com). Information is also available from the National Safety Council, 1121

Spring Lake Drive, Itasca, IL 60143-3201. Please refer to the American National Standards Institute ANSI

01.1 Safety Requirements for Woodworking Machines and the U.S. Department of Labor OSHA 1910.213

Regulations.

SAVE THESE INSTRUCTIONS.

Refer to them often and use them to instruct others.

5

POWER CONNECTIONS

A separate electrical circuit should be used for your machines. This circuit should not be less than #12 wire and should be protected with a 20 Amp time lag fuse. If an extension cord is used, use only 3-wire extension cords which have 3-prong grounding type plugs and matching receptacle which will accept the machine’s plug. Before connecting the machine to the power line, make sure the switch (s) is in the “OFF” position and be sure that the electric current is of the same characteristics as indicated on the machine. All line connections should make good contact. Running on low voltage will damage the machine.

DO NOT EXPOSE THE MACHINE TO RAIN OR OPERATE THE MACHINE IN DAMP LOCATIONS.

MOTOR SPECIFICATIONS

Your machine is wired for 120 volt, 60 HZ alternating current. Before connecting the machine to the power source, make sure the switch is in the “OFF” position.

GROUNDING INSTRUCTIONS

THIS MACHINE MUST BE GROUNDED WHILE IN USE TO PROTECT THE OPERATOR FROM

ELECTRIC SHOCK.

1. All grounded, cord-connected machines:

In the event of a malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This machine is equipped with an electric cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into a matching outlet that is properly installed and grounded in accordance with all local codes and ordinances.

Do not modify the plug provided - if it will not fit the outlet, have the proper outlet installed by a qualified electrician.

I m p ro p e r c o n n e c t i o n o f t h e e q u i p m e n t - g ro u n d i n g cond uc t or can result i n risk of el e ct ric s hoc k . The conductor with insulation having an outer surface that is green with or without yellow stripes is the equipmentgrounding conductor. If repair or replacement of the electric cord or plug is necessary, do not connect the equipmentgrounding conductor to a live terminal.

Check with a qualified electrician or service personnel if the grounding instructions are not completely understood, or if in doubt as to whether the machine is properly grounded.

Use only 3-wire extension cords that have 3-prong grounding type plugs and matching 3-conductor receptacles that accept the machine’s plug, as shown in Fig. A.

Repair or replace damaged or worn cord immediately.

2. Grounded, cord-connected machines intended for use on a supply circuit having a nominal rating less than 150 volts:

If the machine is intended for use on a circuit that has an outlet that looks like the one illustrated in Fig. A, the machine will have a grounding plug that looks like the plug illustrated in Fig. A. A temporary adapter, which looks like the adapter illustrated in Fig. B, may be used to connect this plug to a matching 2-conductor receptacle as shown in Fig. B if a properly grounded outlet is not available. The temporary adapter should be used only until a properly grounded outlet can be installed by a qualified electrician. The green-colored rigid ear, lug, and the like, extending from the adapter must be connected to a permanent ground such as a properly grounded outlet box. Whenever the adapter is used, it must be held in place with a metal screw.

NOTE: In Canada, the use of a temporary adapter is not permitted by the Canadian Electric Code.

IN ALL CASES, MAKE CERTAIN THAT THE

RECEPTACLE IN QUESTION IS PROPERLY

GROUNDED. IF YOU ARE NOT SURE, HAVE

A QUALIFIED ELECTRICIAN CHECK THE

RECEPTACLE.

GROUNDED OUTLET BOX

CURRENT

CARRYING

PRONGS

GROUNDED OUTLET BOX

GROUNDING

MEANS

ADAPTER

GROUNDING BLADE

IS LONGEST OF THE 3 BLADES

Fig. A Fig. B

6

EXTENSION CORDS

Use proper extension cords. Make sure your extension cord is in good condition and is a 3-wire extension cord which has a 3-prong grounding type plug and matching receptacle which will accept the machine’s plug. When using an extension cord, be sure to use one heavy enough to carry the current of the machine. An undersized cord will cause a drop in line voltage, resulting in loss of power and overheating. Fig.

D-1 shows the correct gauge to use depending on the cord length. If in doubt, use the next heavier gauge. The smaller the gauge number, the heavier the cord.

MINIMUM GAUGE EXTENSION CORD

RECOMMENDED SIZES FOR USE WITH STATIONARY ELECTRIC MACHINES

Ampere

Rating Volts

Total Length of Cord in Feet

Gauge of

Extension Cord

0-6

0-6

0-6

0-6

6-10

6-10

6-10

6-10

10-12

10-12

10-12

10-12

12-16

12-16

12-16

120

120

120

120

120

120

120

120

120

120

120

120

120

120

120 up to 25

25-50

50-100

100-150 up to 25

25-50

50-100

100-150

18 AWG

16 AWG

16 AWG

14 AWG

18 AWG

16 AWG

14 AWG

12 AWG up to 25

25-50

50-100

100-150

16 AWG

16 AWG

14 AWG

12 AWG up to 25

25-50

14 AWG

12 AWG

GREATER THAN 50 FEET NOT RECOMMENDED

FUNCTIONAL DESCRIPTION

FOREWORD

The Delta Model 23-700 Universal Wet/Dry Grinder has a 1/5 HP, shielded, induction-type motor that allows a slow speed (70 rpm) on the 10" wet wheel that sharpens hardened cutting tools without damaging the tool’s temper. The 5" dry grinding wheel operates at 3450 rpm for pointing screwdrivers and honing the edge on knives, blades, and other workshop tools.

NOTICE: The photo on the manual cover illustrates the current production model. All other illustrations contained in the manual are representative only and may not depict the actual labeling or accessories included. These are are intended to illustrate technique only.

CARTON CONTENTS

The carton contents include the wet/dry grinder, a 10" diameter aluminum oxide wheel, a 5" diameter aluminum oxide wheel, tool rests, a sliding angle jig, an eye shield, a wheel guard with a removable side plate, and an instruction manual.

UNPACKING AND CLEANING

Carefully unpack the machine and all loose items from the shipping container(s). Remove the protective coating from all unpainted surfaces. This coating may be removed with a soft cloth moistened with kerosene (do not use acetone, gasoline or lacquer thinner for this purpose). After cleaning, cover the unpainted surfaces with a good quality household floor paste wax.

7

ASSEMBLY

ASSEMBLY TOOLS REQUIRED

Phillips Screwdriver Adjustable Wrench

ASSEMBLY TIME ESTIMATE

Approximately 30 Minutes

ATTACHING AND ADJUSTING THE EYE SHIELD

1.

Fasten the eye shield (A) Fig. 1 to the mounting bracket

(B) using the two screws (C) and nuts (D).

2.

Use the knob screw and washer (G) Figs. 1 to attach the eye shield and the mounting bracket assembly (E)

Fig. 3 to the side of the grinding wheel guard (F).

3.

The eye shield (A) Fig. 3 is adjustable. Place it in any position by loosening the lock knob (H) and moving the shield (A).

D

B

Fig. 1

G

E

A

A

F

Fig. 2 Fig. 3

H

G

C

ATTACHING AND ADJUSTING THE TOOL RESTS

1.

Attach the tool rest (A) Fig. 5 to the wheel guard using the lock knob screw (B), nut, and washer.

2.

The tool rest (A) Fig. 5 is adjustable so it can be positioned as close to the grinding wheel as possible giving maximum support to the piece that is being ground, by loosening lock knob (B), moving tool rest (A) to the desired position and tightening lock knob (B). As the grinding wheel wears down to a smaller diameter, re-adjust the tool rest closer to the wheel. The tool rest (A) should be adjusted so it is set a little below the center of the wheel. This is the most practical and safest position for general work. Free hand grinding without the use of the tool rest should always be done on the lower quarter of the wheel.

3.

The tool rest for the 10” grinding wheel can be attached to the right hand side of the machine as shown in Fig. 67, or can be assembled to the left hand side of the machine as shown in Fig. 7. Assemble the tool rest (C) Figs. 7 and 7 to the machine as desired, using two 1” hex head screws and flat washers (D), one of which is shown.

NOTE: When the tool rest is attached to the left side of the machine, the grinding action will be on the upward swing.The

tool rest (C) Figs. 6 and 7, is adjustable so it can be positioned close to the grinding wheel and at any angle to the wheel by loosening two locking handles (E), adjusting the tool rest (C), and tightening the two locking handles (E). The locking handles (E) are spring-loaded and can be repositioned by pulling outward on each handle and repositioning it on the serrated nut located underneath the handle.

8

B A

B A

Fig. 4 Fig. 5

C

E C E

D

E

D

Fig. 7

Fig. 6

ADJUSTING THE SPARK DEFLECTOR

As the five inch grinding wheel (H) Fig. 8, wears down due to extended use, the spark deflector (J) should be adjusted downward with it, so it is always set close to the grinding wheel for maximum operator safety. To adjust the spark deflector, loosen the screw (K) Fig. 8, position the spark deflector (J) close to the surface of the grinding wheel, and retighten the screw

(K).

SLIDING ANGLE JIG

A sliding angle jig (A) Fig. 9 is supplied to provide accurate compound angles (right or left) of up to 45° with the 10" wheel.

J

H

A

K

Fig. 8

FASTENING THE WET/DRY GRINDER TO A SUPPORTING SURFACE

Fig. 9

A

The Wet/Dry Grinder should always be secured to a supporting surface using the four mounting holes, three of which are shown at (A) Fig. 10.

Fig. 10

9

OPERATION

OPERATIONAL CONTROLS AND ADJUSTMENTS

STARTING AND STOPPING THE MACHINE

1.

The on/off switch (A) Fig. 11 is located on the front of the grinder. To turn the machine “ON”, move the switch up to the “ON” position.

2.

To turn the machine “OFF”, move the switch (A) down to the “OFF” position.

Make sure that the switch is in the “OFF” position before plugging in the power cord. In the event of a power failure, move the switch to the “OFF” position.

An accidental start-up can cause injury.

IMPORTANT: When the machine is not in use, the switch should be locked in the “OFF” position to prevent unauthorized use, using a padlock with a 3/16" diameter shackle through the two holes in the switch plate.

Fig. 11

A

B

WATER LEVEL

The 10" grinding wheel requires water. Keep the water level in the base (A) Fig. 12 sufficient to cover at least 1" of the lower portion of the grinding wheel. Add water as needed during the grinding operation.Remove the drain plug (B) Fig. 13 to drain the water from the base .

A

B

Fig. 12 Fig. 13

GRINDING WHEELS

For best grinding results and to maintain good balance, always keep the wheels properly dressed. Do not force work against a cold wheel but use light pressure until the wheel becomes warm. It is earnestly recommended that only balanced wheels be used. The use of balanced wheels adds years to the life of the bearings in any grinder, and by eliminating the most common source of vibration, more accurate work is accomplished.Your dealer can order special wheels, given the size, thickness, arbor diameter and grade, from any reliable grinding wheel company, but be sure that they are balanced for perfect results and rated for the proper speed or higher.

DRESSING A GRINDING WHEEL

SILICON CARBIDE

GRINDING

WHEEL

Use a suitable silicon carbide stick-type dresser (Fig. 14).

Move the dresser forward until it touches the high point of the face of the wheel. Dress the wheel by moving the dresser back and forth. Repeat this operation until the face of the wheel is clean and the corners are square.

STICK

DRESSER

Fig. 14

10

TOOL

REST

CHANGING THE GRINDING WHEELS

When changing the 5” grinding wheel, remove the eye shield, tool rest and side cover. Loosen and remove the arbor nut (A) Fig. 15 by turning it toward you (counterclockwise). To prevent shaft rotation, hold the grinding wheel by hand.

IMPORTANT: Do not overtighten the arbor nut (A)

when you install a new wheel.

To change the 10” grinding wheel, remove the screws (A)

Fig. 16.

Lift the complete motor assembly (A) Fig. 17 from the base

(B). Remove the bearing block (C) from the end of the shaft.

Hold the grinding wheel and turn the arbor nut (D) Fig. 18, away from you (counter-clockwise) to loosen and remove the nut (D).

IMPORTANT: Do not overtighten the arbor nut (D) when you install a new wheel.

B

Fig. 15

A

Fig. 16

D

A

A

C

Fig. 17 Fig. 18

MACHINE USE

5" DRY GRINDING WHEEL

The 5" diameter aluminum oxide grinding wheel operates at 3450 RPM. It is used for operations such as pointing screwdrivers (Fig. 19), sharpening scissors, putty knives. wood chisels, and drill bits (Fig. 20).

Set the tool rest (A) Fig. 19 slightly below the center of the grinding wheel for general work. Adjust it so that it supports the tool at the proper grinding angle. Make certain that you take all safety precautions before applying power to the machine.

Fig. 19

11

Fig. 20

10" WET GRINDING WHEEL

The 10" aluminum oxide grinding wheel operates at a slow speed of 70 RPM. This speed is suitable for honing garden tools, or sharpening chisels, and axes (Fig.

21).

During operation, keep the water level in the reservoir (A)

Fig. 26 at a 1" depth. This level will keep the wheel constantly wet and keep hardened tools cool without damaging their temper. The large wheel also is used to remove burrs from tools requiring keen edges.

The sliding angle jig is used to sharpen tools with compound cutting angles (Fig. 22).

Adjust the tool rest so that it supports the tool at the exact grinding angle close to the grinding wheel.

Observe all safety precautions before applying power to the machine.

Fig. 21

Fig. 22

TROUBLESHOOTING

For assistance with your machine, visit our website at www.deltamachinery.com for a list of service centers or call the DELTA Machinery help line at 1-800-223-7278 (In Canada call 1-800-463-3582).

12

MAINTENANCE

LUBRICATION

Periodically, lubricate the arbor shaft with light machine oil, through the oiler (A) Fig. 23.

To lubricate the worm gears, remove the nameplate (C) and apply grease to the two gears (A) and (B) Fig. 24.

A

B

A

C

Fig. 23

A

Fig. 24

KEEP MACHINE CLEAN

Periodically blow out all air passages with dry compressed air. All plastic parts should be cleaned with a soft damp cloth. NEVER use solvents to clean plastic parts. They could possibly dissolve or otherwise damage the material.

Wear ANSI Z87.1 safety glasses while using compressed air.

FAILURE TO START

Should your machine fail to start, check to make sure the prongs on the cord plug are making good contact in the outlet. Also, check for blown fuses or open circuit breakers in the line.

LUBRICATION

Apply household floor paste wax to the machine table and extension table or other work surface weekly.

PROTECTING CAST IRON FROM RUST

To clean and protect cast iron tables from rust, you will need the following materials: 1 pushblock from a jointer,

1 sheet of medium Scotch-Brite™ Blending Hand Pad, 1 can of WD-40 ® , 1 can of degreaser, 1 can of TopCote ®

Aerosol. Apply the WD-40 and polish the table surface with the Scotch-Brite pad using the pushblock as a holddown. Degrease the table, then apply the TopCote ® accordingly.

13

SERVICE

PARTS, SERVICE OR WARRANTY ASSISTANCE

All Delta Machines and accessories are manufactured to high quality standards and are serviced by a network of Porter-Cable

Delta Factory Service Centers and Delta Authorized Service Stations. To obtain additional information regarding your Delta quality product or to obtain parts, service, warranty assistance, or the location of the nearest service outlet, please call 1-800-223-7278 (In Canada call 1-800-463-3582).

ACCESSORIES

A complete line of accessories is available from your Delta Supplier, Porter-Cable • Delta Factory Service Centers, and Delta Authorized Service Stations. Please visit our Web Site

www.deltamachinery.com

for a catalog or for the name of your nearest supplier.

Since accessories other than those offered by Delta have not been tested with this product, use of such accessories could be hazardous. For safest operation, only

Delta recommended accessories should be used with this product.

14

WARRANTY

Two Year Limited New Product Warranty

Delta will repair or replace, at its expense and at its option, any new Delta machine, machine part, or machine accessory which in normal use has proven to be defective in workmanship or material, provided that the customer returns the product prepaid to a Delta factory service center or authorized service station with proof of purchase of the product within two years and provides Delta with reasonable opportunity to verify the alleged defect by inspection. For all refurbished Delta product, the warranty period is 180 days. Delta may require that electric motors be returned prepaid to a motor manufacturer’s authorized station for inspection and repair or replacement. Delta will not be responsible for any asserted defect which has resulted from normal wear, misuse, abuse or repair or alteration made or specifically authorized by anyone other than an authorized Delta service facility or representative. Under no circumstances will Delta be liable for incidental or consequential damages resulting from defective products. This warranty is Delta’s sole warranty and sets forth the customer’s exclusive remedy, with respect to defective products; all other warranties, express or implied, whether of merchantability, fitness for purpose, or otherwise, are expressly disclaimed by Delta.

15

PORTER-CABLE

DELTA SERVICE CENTERS

(CENTROS DE SERVICIO DE PORTER-CABLE

DELTA)

Parts and Repair Service for Porter-Cable

Delta Machinery are Available at These Locations

(Obtenga Refaccion de Partes o Servicio para su Herramienta en los Siguientes Centros de Porter-Cable

Delta)

ARIZONA

Phoenix 85013-2906

4501 N. 7th Ave.

Phone: (602) 279-6414

Fax: (602) 279-5470

CALIFORNIA

Ontario 91761 (Los Angeles)

3949A East Guasti Road

Phone: (909) 390-5555

Fax: (909) 390-5554

San Diego 92111

7290 Clairemont Mesa Blvd.

Phone: (858) 279-2011

Fax: (858) 279-0362

San Leandro 94577 (Oakland)

3039 Teagarden Street

Phone: (510) 357-9762

Fax: (510) 357-7939

COLORADO

Denver 80223

700 West Mississippi Ave.

Phone: (303) 922-8325

Fax: (303) 922-0245

GEORGIA

Forest Park 30297 (Atlanta)

5442 Frontage Road,

Suite 112

Phone: (404) 608-0006

Fax: (404) 608-1123

ILLINOIS

Addison 60101 (Chicago)

400 South Rohlwing Rd.

Phone: (630) 424-8805

Fax: (630) 424-8895

OREGON

Portland 97230

14811 North East Airport Way

Phone: (503) 255-6556

Fax: (503) 255-6543

PENNSYLVANIA

Willow Grove 19090

(Philadelphia)

520 North York Road

Phone: (215) 658-1430

Fax: (215) 658-1433

TEXAS

Carrollton 75006 (Dallas)

1300 Interstate 35 N, Suite 112

Phone: (972) 446-2996

Fax: (972) 446-8157

Houston 77022-2122

536 East Tidwell Rd.

Phone: (713) 692-7111

Fax: (713) 692-1107

WASHINGTON

Auburn 98001(Seattle)

3320 West Valley HWY, North

Building D, Suite 111

Phone: (253) 333-8353

Fax: (253) 333-9613

FLORIDA

Davie 33314 (Miami)

4343 South State Rd. 7 (441)

Unit #107

Phone: (954) 321-6635

Fax: (954) 321-6638

Tampa 33634

4909 West Waters Ave.

Phone: (813) 884-0434

Fax: (813) 888-5997

KANSAS

Overland Park 66214

9201 Quivira Road

Phone: (913) 495-4330

Fax: (913) 495-4378

MARYLAND

Elkridge 21075 (Baltimore)

7397-102 Washington Blvd.

Phone: (410) 799-9394

Fax: (410) 799-9398

MASSACHUSETTS

Franklin 02038 (Boston)

Franklin Industrial Park

101E Constitution Blvd.

Phone: (508) 520-8802

Fax: (508) 528-8089

MICHIGAN

Madison Heights 48071 (Detroit)

30475 Stephenson Highway

Phone: (248) 597-5000

Fax: (248) 597-5004

MINNESOTA

Eden Prairie 55344

9709 Valley View Road

Phone: (952) 884-9191

Fax: (952) 884-3750

MISSOURI

St. Louis 63146

11477 Page Service Drive

Phone: (314) 997-9100

Fax: (314) 997-9183

NEW YORK

Flushing 11365-1595 (N.Y.C.)

175-25 Horace Harding Expwy.

Phone: (718) 225-2040

Fax: (718) 423-9619

NORTH CAROLINA

Charlotte 28270

9129 Monroe Road, Suite 115

Phone: (704) 841-1176

Fax: (704) 708-4625

OHIO

Columbus 43229

1948 Schrock Road

Phone: (614) 895-3112

Fax: (614) 895-3187

Parma Heights OH 44130

6485 Pearl Road

Phone: (440) 842-9100

Fax: (440) 884-3430

Authorized Service Stations are located in many large cities. Telephone 800-438-2486 or 731-541-6042 for assistance locating one.

Parts and accessories for Porter-Cable

·

Delta products should be obtained by contacting any Porter-Cable

·

Delta Distributor, Authorized

Service Center, or Porter-Cable

·

Delta Factory Service Center. If you do not have access to any of these, call 800-223-7278 and you will be directed to the nearest Porter-Cable

·

Delta Factory Service Center. Las Estaciones de Servicio Autorizadas están ubicadas en muchas grandes ciudades. Llame al 800-438-2486 ó al 731-541-6042 para obtener asistencia a fin de localizar una. Las piezas y los accesorios para los productos Porter-Cable

·

Delta deben obtenerse poniéndose en contacto con cualquier distribuidor Porter-Cable

·

Delta, Centro de Servicio Autorizado o Centro de Servicio de Fábrica Porter-Cable

·

Delta. Si no tiene acceso a ninguna de estas opciones, llame al

800-223-7278 y le dirigirán al Centro de Servicio de Fábrica Porter-Cable

·

Delta más cercano.

CANADIAN PORTER-CABLE

DELTA SERVICE CENTERS

ALBERTA

Bay 6, 2520-23rd St. N.E.

Calgary, Alberta

T2E 8L2

Phone: (403) 735-6166

Fax: (403) 735-6144

MANITOBA

1699 Dublin Avenue

Winnipeg, Manitoba

R3H 0H2

Phone: (204) 633-9259

Fax: (204) 632-1976

QUÉBEC

1515 ave.

St-Jean Baptiste, Suite 160

Québec, Québec

G2E 5E2

Phone: (418) 877-7112

Fax: (418) 877-7123

BRITISH COLUMBIA

8520 Baxter Place

Burnaby, B.C.

V5A 4T8

Phone: (604) 420-0102

Fax: (604) 420-3522

ONTARIO

505 Southgate Drive

Guelph, Ontario

N1H 6M7

Phone: (519) 767-4132

Fax: (519) 767-4131

1447, Begin

St-Laurent, (Montréal),

Québec

H4R 1V8

Phone: (514) 336-8772

Fax: (514) 336-3505

The following are trademarks of PORTER-CABLE DELTA (Las siguientes son marcas registradas de PORTER-CABLE DELTA S.A.) (Les marques suivantes sont des marques de fabriquant de la PORTER-CABLE DELTA): Auto-Set ® , BAMMER ® , B.O.S.S.

® , Builder’s Saw ® , Contractor’s Saw ® ,

Contractor’s Saw II™, Delta ® , DELTACRAFT ® , DELTAGRAM™, Delta Series 2000™, DURATRONIC™, Emc²™, FLEX ® , Flying Chips™, FRAME SAW ® ,

Grip Vac™, Homecraft ® , INNOVATION THAT WORKS ® , Jet-Lock ® , JETSTREAM ® , ‘kickstand ® , LASERLOC ® , MICRO-SET ® , Micro-Set ® , MIDI LATHE ® ,

MORTEN™, NETWORK™, OMNIJIG ® , POCKET CUTTER ® , PORTA-BAND ® , PORTA-PLANE ® , PORTER-CABLE ® &(design), PORTER-

CABLE ® PROFESSIONAL POWER TOOLS, PORTER-CABLE REDEFINING PERFORMANCE™, Posi-Matic ® , Q-3 ® &(design), QUICKSAND ® &(design),

QUICKSET™, QUICKSET II ® , QUICKSET PLUS™, RIPTIDE™&(design), SAFE GUARD II ® , SAFE-LOC ® , Sanding Center ® , SANDTRAP ® &(design), SAW

BOSS ® , Sawbuck™, Sidekick ® , SPEED-BLOC ® , SPEEDMATIC ® , SPEEDTRONIC ® , STAIR EASE ® , The American Woodshop ® &(design), The Lumber

Company ® &(design), THE PROFESSIONAL EDGE ® , THE PROFESSIONAL SELECT ® , THIN-LINE™, TIGER ® , TIGER CUB ® , TIGER SAW ® ,

TORQBUSTER ® , TORQ-BUSTER ® , TRU-MATCH™, TWIN-LITE ® , UNIGUARD ® , Unifence ® , UNIFEEDER™, Unihead ® , Uniplane™, Unirip ® , Unisaw ® ,

Univise ® , Versa-Feeder ® , VERSA-PLANE ® , WHISPER SERIES ® , WOODWORKER’S CHOICE™.

Trademarks noted with ™ and ® are registered in the United States Patent and Trademark Office and may also be registered in other countries. Las

Marcas Registradas con el signo de ™ y ® son registradas por la Oficina de Registros y Patentes de los Estados Unidos y también pueden estar registradas en otros países.

PC7.2-0105-149

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement