LTC 2604
Instruction Manual
EN Multiplexer Keyboard
Port Expander
LTC 2604 | Instruction Manual | Important Safeguards
EN | 2
Important Safeguards
1. Read, Follow, and Retain Instructions - All safety
and operating instructions should be read and
followed before operating the unit. Retain instructions
for future reference.
2. Heed Warnings - Adhere to all warnings on the unit
and in the operating instructions.
3. Attachments - Attachments not recommended by the
product manufacturer should not be used, as they
may cause hazards.
4. Installation Cautions - Do not place this unit on an
unstable stand, tripod, bracket, or mount. The unit
may fall, causing serious injury to a person and
serious damage to the unit. Use only manufacturerrecommended accessories, or those sold with the
product. Mount the unit per the manufacturer's
instructions. Appliance and cart combination should
be moved with care. Quick stops, excessive force, or
uneven surfaces may cause the appliance and cart
combination to overturn.
5. Cleaning - Unplug the unit from the outlet before
cleaning. Follow any instructions provided with the
unit. Generally, using a damp cloth for cleaning is
sufficient. Do not use liquid cleaners or aerosol
cleaners.
6. Servicing - Do not attempt to service this unit
yourself. Opening or removing covers may expose
you to dangerous voltage or other hazards. Refer all
servicing to qualified service personnel.
7. Damage Requiring Service - Unplug the unit from
the main AC power source and refer servicing to
qualified service personnel under the following
conditions:
• When the power supply cord or plug is damaged.
• If liquid has been spilled or an object has fallen
into the unit.
• If the unit has been exposed to water and/or
inclement weather (rain, snow, etc.).
• If the unit does not operate normally, when
following the operating instructions. Adjust only
those controls specified in the operating
instructions. Improper adjustment of other controls
may result in damage, and require extensive work
by a qualified technician to restore the unit to
normal operation.
• If the unit has been dropped or the cabinet
damaged.
• If the unit exhibits a distinct change in
performance, this indicates that service is needed.
8. Replacement Parts - When replacement parts are
required, the service technician should use
replacement parts specified by the manufacturer or
that have the same characteristics as the original part.
Unauthorized substitutions may result in fire,
electrical shock or other hazards.
9. Safety Check - Upon completion of servicing or
repairs to the unit, ask the service technician to
perform safety checks to ensure proper operating
condition.
Bosch Security Systems | October 22, 2004
10. Power Sources - Operate the unit only from the type
of power source indicated on the label. If unsure of
the type of power supply to use, contact your dealer
or local power company.
• For units intended to operate from battery power,
refer to the operating instructions.
• For units intended to operate with External Power
Supplies, use only the recommended approved
power supplies.
• For units intended to operate with a limited power
source, this power source must comply with
EN60950. Substitutions may damage the unit or
cause fire or shock.
• For units intended to operate at 24VAC, normal
input voltage is 24VAC. Voltage applied to the
unit's power input should not exceed 30VAC.
User-supplied wiring, from the 24VAC supply to
unit, must be in compliance with electrical codes
(Class 2 power levels). Do not ground the 24VAC
supply at the terminals or at the unit's power
supply terminals.
11. Coax Grounding - If an outside cable system is
connected to the unit, ensure that the cable system is
grounded. U.S.A. models only - Section 810 of the
National Electrical Code, ANSI/NFPA No.70,
provides information regarding proper grounding of
the mount and supporting structure, grounding of the
coax to a discharge unit, size of grounding
conductors, location of discharge unit, connection to
grounding electrodes, and requirements for the
grounding electrode.
12. Grounding or Polarization - This unit may be
equipped with a polarized alternating current line
plug (a plug with one blade wider than the other).
This safety feature allows the plug to fit into the
power outlet in only one way. If unable to insert the
plug fully into the outlet, try reversing the plug. If the
plug still fails to fit, contact an electrician to arrange
replacement of the obsolete outlet. Do not defeat the
safety purpose of the polarized plug.
Alternately, this unit may be equipped with a
3-wire grounding plug (a plug with a third pin, for
grounding). This safety feature allows the plug to fit
into a grounding power outlet only. If unable to insert
the plug into the outlet, contact an electrician to
arrange replacement of the obsolete outlet. Do not
defeat the safety purpose of the grounding plug.
13. Lightning - For added protection during a lightning
storm, or when this unit is left unattended and unused
for long periods of time, unplug the unit from the
wall outlet and disconnect the cable system. This will
prevent damage to the unit due to lightning and
power line surges.
EN | 3
LTC 2604 | Instruction Manual | FCC Information
For Indoor Product
1. Water and Moisture - Do not use this unit near
water - for example, in a wet basement, in an
unprotected outdoor installation or in any area
classified as a wet location.
2. Object and Liquid Entry - Never push objects of
any kind into this unit through openings, as they
may touch dangerous voltage points or short out
parts that could result in a fire or electrical shock.
Never spill liquid of any kind on the unit.
3. Power Cord and Power Cord Protection - For
units intended to operate with 230VAC, 50Hz,
the input and output power cord must comply
with the latest versions of IEC Publication 227 or
IEC Publication 245.
Power supply cords should be routed so they are
not likely to be walked on or pinched. Pay
particular attention to location of cords and plugs,
convenience receptacles, and the point of exit
from the appliance.
4. Overloading - Do not overload outlets and
extension cords; this can result in a risk of fire or
electrical shock.
For Outdoor Product
Power Lines - An outdoor system should not be
located in the vicinity of overhead power lines,
electric lights or power circuits, or where it may
contact such power lines or circuits. When
installing an outdoor system, extreme care should
be taken to keep from touching power lines or
circuits, as this contact might be fatal. U.S.A.
models only - refer to the National Electrical
Code Article 820 regarding installation of CATV
systems.
For Rack-mount Product
1. Ventilation - This unit should not be placed in a
built-in installation or rack, unless proper
ventilation is provided, or the manufacturer’s
instructions have been adhered to. The
equipment must not exceed its maximum
operating temperature requirements.
2. Mechanical Loading - Mounting of the
equipment in a rack shall be such that a
hazardous condition is not achieved due to
uneven mechanical loading.
Bosch Security Systems | October 22, 2004
ATTENTION
OBSERVE PRECAUTIONS
FOR HANDLING
ELECTROSTATIC SENSITIVE
DEVICES
WARNING:
Electrostatic-sensitive device. Use
proper CMOS/MOSFET handling
precautions to avoid electrostatic
discharge.
NOTE: Grounded wrist straps must be worn and proper ESD
safety precautions observed when handling the electrostaticsensitive printed circuit boards.
FCC & ICES INFORMATION
(U.S.A. and Canadian Models Only)
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions:
(1)
This device may not cause harmful interference, and
(2)
This device must accept any interference received,
including interference that may cause undesired
operation.
NOTE: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules and ICES-003 of Industry Canada. These limits
are designed to provide reasonable protection against harmful
interference when the equipment is operated in a residential
installation. This equipment generates, uses and can radiate radio
frequency energy, and if not installed and used in accordance
with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
• Consult the dealer, or an experienced radio/TV technician for
help.
Intentional or unintentional changes or modifications, not
expressly approved by the party responsible for compliance, shall
not be made. Any such changes or modifications could void the
user’s authority to operate the equipment.The user may find the
following booklet, prepared by the Federal Communications
Commission, helpful: How to Identify and Resolve Radio-TV
Interference Problems. This booklet is available from the U.S.
Government Printing Office, Washington, DC 20402, Stock No.
004-000-00345-4.
EN | 4
LTC 2604 | Instruction Manual | Safety Precautions
Safety Precautions
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE COVER
(OR BACK). NO USER SERVICEABLE PARTS
INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
This symbol indicates the presence of
uninsulated “dangerous voltage” within the
product’s enclosure. This may constitute a
risk of electric shock.
The user should consult the operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
Attention: Installation should be performed by
qualified service personnel only in accordance
with the National Electrical Code or applicable
local codes.
Power Disconnect. Units with or without
ON-OFF switches have power supplied to the
unit whenever the power cord is inserted into the
power source; however, the unit is operational
only when the ON-OFF switch is in the ON
position. The power cord is the main power
disconnect for all units.
Bosch Security Systems | October 22, 2004
Sécurité
ATTENTION : POUR ÉVITER TOUT RISQUE
D'ÉLECTROCUTION, N'ESSAYEZ PAS DE
RETIRER LE CAPOT (OU LE PANNEAU
ARRIÈRE). CET APPAREIL NE CONTIENT
AUCUN COMPOSANT SUSCEPTIBLE D'ÊTRE
RÉPARÉ PAR L'UTILISATEUR. CONFIEZ LA
RÉPARATION DE L'APPAREIL À DU
PERSONNEL QUALIFIÉ.
Ce symbole signale que le produit renferme
une « tension potentiellement dangereuse »
non isolée susceptible de provoquer une
électrocution.
Ce symbole invite l'utilisateur à consulter
les instructions d'utilisation et d'entretien
(dépannage) reprises dans la documentation
qui accompagne l'appareil.
Attention : l'installation doit exclusivement être
réalisée par du personnel qualifié, conformément
au code national d'électricité américain (NEC) ou
au code d'électricité local en vigueur.
Coupure de l'alimentation. Qu'ils soient pourvus
ou non d'un commutateur ON/OFF, tous les
appareils reçoivent de l'énergie une fois le cordon
branché sur la source d'alimentation. Toutefois,
l'appareil ne fonctionne réellement que lorsque
le commutateur est réglé sur ON. Le
débranchement du cordon d'alimentation permet
de couper l'alimentation des appareils.
EN | 5
LTC 2604 | Instruction Manual | Contents
Table of Contents
Important Safeguards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
FCC Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
1
UNPACKING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
2
SERVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
3
DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
4
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
4.1
Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
4.2
Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
4.3
Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
5
OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
1
UNPACKING
This equipment should be unpacked and handled with
care. If an item appears to have been damaged in
shipment, return it properly back into its carton and
notify the shipper.
Verify that all parts shown in the Parts List have been
included. If any items are missing, notify your Bosch
Security Systems Sales or Customer Service
Representative.
The original packing carton is the safest container in
which to transport the unit. Save it for possible future
use.
1.1
Parts List
Qty
Item
1
White cable assembly with RJ11 connectors
2
LTC 8557 Series Keyboard Extension Kits
1
Port Expander
Bosch Security Systems | October 22, 2004
2
SERVICE
If the unit ever needs repair service, contact the
nearest Bosch Security Systems Inc. Service Center
for authorization to return and shipping instructions.
Service Centers
USA
Phone:
800-366-2283 or 717-735-6638
Fax:
800-366-1329 or 717-735-6639
CCTV Spare Parts
Phone:
800-894-5215 or 408-956-3853 or 3854
Fax:
408-957-3198
E-mail:
BoschCCTVparts@ca.slr.com
Canada
Phone:
514-738-2434
Europe, Middle East & Asia Pacific Region
Phone:
32-1-440-0711
For additional information, see
www.boschsecuritysystems.com.
EN | 6
LTC 2604 | Instruction Manual | Description
3
4.3
DESCRIPTION
This publication provides instructions for installing the
LTC 2604 Multiplexer Keyboard Port Expander in a
LTC 2600 System 4 Multiplexer System.
A single LTC 2604 unit can be used to interface up to
four keyboards in a Multiplexer system.
The LTC 2604 unit is compatible with any
combination of the following models of keyboards:
4.3.1 Expanding Up To Four Keyboards Using The
LTC 2604 Multiplexer Keyboard Port Expander
1. Make sure power is turned OFF on the
Multiplexer and the LTC 2604 Multiplexer
Keyboard Port Expander. Make sure that the
external power supplies used to power the
Multiplexer series keyboards are not connected
to a wall outlet.
2. The LTC 8557 Series kit consists of two junction
boxes, a power supply, a barrel plug cord and a
keyboard cable.
LTC 2601/00, LTC 2602/00, KBD-DIGITAL,
KBD-MUX, or KBD-UNIVERSAL, Divar® Series
Recorders.
3. Connect the cable supplied with the keyboard
between the keyboard and the remote junction
box.
For more than two LTC 2601/2 keyboards used in an
expanded configuration, one LTC 8557 Series Keyboard
Extension Kit (not included) will be required for each
additional keyboard.
Each Multiplexer Keyboard Port Expander is supplied
with a single white cable. This cable is used to connect
the Port Expander to the keyboard port of a System4
Multiplexer. The LTC 8557 Series Kit is then used to
connect the expanded keyboards to the LTC 2604 Port
Expander. See Typical Application Diagrams found at
the end of this manual.
4
INSTALLATION
Connections
4. Up to 1.5 km (5000 ft) of customer supplied
0.5 mm2 (24 AWG) shielded twisted pair (Belden
9841 or equivalent) may be run between the two
junction boxes. Connection to the junction boxes
are made to three of the four screw terminals as
follows. Note reversal to data connections.
Terminal Number
Remote Keyboard
Junction Box
Local
Junction Box
1
2
3
4
Spare
+
Shield
Spare
+
Shield
NOTE: LTC 2604 Series must be used with System4
models LTC 2670 Series, LTC 2680 Series Video
Controllers with firmware version 2.07 or higher, or
the Divar Series of Recorders. To verify the firmware
version, check the firmware version in the main menu
(see LTC 2600 Series Installation Instructions or Quick
Reference Card) or on the product label of the
LTC 2670 Series or LTC 2680 Series Video
Controllers.
5. Connect the cable supplied with the LTC 8557
Series kit between the junction box and the Kbd
X Input connector on the LTC 2604 Keyboard
Port Expander. Connect the power supply to the
junction box at the remote keyboard site. Verify
that the junction box power LED indicator lights.
Also verify that the keyboard LEDs are flashing.
4.1
7. Using the white cable supplied with the
LTC 2604 Series Keyboard Port Expander,
connect one end of the cable to the connector
marked Multiplexer Output on the LTC 2604 unit.
If connecting to a model LTC 26xx/50 or
LTC 26xx/60 Series Multiplexer, connect the
other end of the white cable to the Y adaptor that
is plugged into the receptacle marked KEYBD on
the multiplexer unit. If connecting to a model
LTC 26xx/90 Series Multiplexer, connect the
other end of the white cable directly to the
receptacle marked as IN on the multiplexer unit.
See Typical LTC 2604 Multiplexer Keyboard Port
Expander Application.
Power
Model
No.
Rated
Voltage
Voltage
Range
Power at
Rated
Voltage
LTC 2604/60
120 VAC,
50/60 Hz
105 to 130
10 W
LTC 2604/50
220-240 VAC,
50/60 Hz
198 to 264
10 W
4.2
Mounting
These units are supplied as desk top units. For rack
mounting, the LTC 9101/00 Rack-mount Kit is
available. These units are half-rack units.
Bosch Security Systems | October 22, 2004
6. Similarly, repeat step 5 for each Multiplexer
Series Keyboard.
EN | 7
LTC 2604 | Instruction Manual | Operation
5
2. The Kbd Active LEDs on the LTC 2604
Multiplexer Keyboard Port Expander will
indicate active data communication to a
connected keyboard. The Multiplexer Active LED
on the front panel of an LTC 2604 Muliplexer
Keyboard Port Expander will indicate
communication between the System 4
Multiplexer and the LTC 2604.
OPERATION
1. Turn on the System 4 Multiplexer or Divar
Recorder and the LTC 2604 Multiplexer
Keyboard Port Expander. The power LED on
the LTC 2604 unit should be on.
MULTIPLEXER
OUTPUT
KEYBD 1 KEYBD 2
INPUT
INPUT
KEYBD 3 KEYBD 4
INPUT
INPUT
Rear Connection
On
Multiplexer
1
2
3
Front Panel
Figure 1: LTC 2604 Multiplexer Keyboard Port Expander
Bosch Security Systems | October 22, 2004
4
Video
AutoDome
Video
AutoDome
PIR Sensor
Data
Video
Up to 16 cameras
To Multiple System 4
KE YB D
S VHS IN
CONS OLE
S VHS OUT
VCR
IN
S DA
MON B
VCR
OUT
MON A
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
ALAR M
White Cable
Out
RS-232
In
LTC 2604 SERIES
Multiplexer
Output
KEYBD1
INPUT
KEYBD2
INPUT
KEYBD3
INPUT
KEYBD4
INPUT
LTC 8557 Series
Bosch
LTC 8557 SERIES
User Supplied
Shield Twisted Pair
Power Supply
ALLP LE X - - -
User Supplied
Shield Twisted Pair
User Supplied
Shield Twisted Pair
LTC 8557 SERIES
User Supplied
Shield Twisted Pair
ALLP LE X - - -
Power Supply
LTC 8558/00 Cable
Power Supply
ALLP LE X - - -
Bosch
Bosch
Power Supply
ALLP LE X - - -
Bosch
Figure 2: Typical System Configuration
Bosch Security Systems, Inc.
850 Greenfield Road
Lancaster, PA 17601 USA
Tel: 800-326-3270
Fax: 1-717-735-6560
www.boschsecuritysystems.com
Bosch Security Systems B.V.
P.O. Box 80002
5600 JB Eindhoven
The Netherlands
Tele +31 40 27 87113
Bosch Security Systems Pte Ltd.
38C Jalan Pemimpin
Singapore 577180
Republic of Singapore
Tel: 65 (6) 319 3486
© 2004 Bosch Security Systems GmbH
3935 890 18112 04-43 | Updated October 22, 2004 | Data subject to change without notice.