- Computers & electronics
- Computer components
- Chassis components
- Console extenders
- Extron
- DTP HDMI 301
- Manual
Extron DTP HDMI 301 Manual
Add to my manuals
Extron electronics DTP HDMI 301 is a digital video extender that allows you to transmit an HDCP-compliant HDMI signal up to 330 feet (100 m) over a single Cat 5e/6/7 cable. It supports resolutions up to 1920x1200, including 1080p, and features built-in equalization and amplification to ensure a reliable signal. The DTP HDMI 301 also includes analog audio input and output ports, as well as RS-232 and IR control ports, making it a versatile solution for a variety of applications.
advertisement
DTP HDMI 301 • Setup Guide
This guide provides quick start instructions for an experienced installer to set up and operate
Extron DTP HDMI 301 digital video extender. The DTP 301 transmitter and receiver pair can extend an HDCP-compliant HDMI signal up to 330 feet (100 m).
Installation
Step 1 — Mounting
Turn off or disconnect all equipment power sources and mount the Tx and Rx units as required.
POWER
12V
0.6 A MAX
INPUTS
AUDIO
SIG LINK
OUT
RS-232 IR
POWER
12V
0.6 A MAX
IN
SIG LINK
OUTPUTS
AUDIO
7 1 2
DTP OUT
ANALOG AUDIO Tx Rx Tx Rx
4 3 7
ANALOG AUDIO
DTP IN
4 5 6
Step 2 — Connections
a HDMI Input connector (Tx) — Connect an HDMI cable between this port and the HDMI output port of the digital video source.
INPUTS
AUDIO b Audio input (Tx) — Connect an unbalanced stereo audio source to this 3.5 mm mini stereo jack for an analog audio input.
c RS-232 and IR connectors — To pass serial or infrared data or control signals, such as serial control of a projector, connect the master device to the transmitter and the slave device to the receiver via the RS-232 and IR captive screw connectors on both units.
d DTP and Analog Audio (Output and Input) RJ-45 connectors — Connect one or two TP cables between these RJ-45 female connectors on the transmitter and receiver.
RS-232 IR
Tx
Tx/Rx
Pins
Rx
3
Tx Rx DTP HDMI 301 Rx
Connected RS-232 and IR Device Pins
Transmit pin on connected unit
Receive pin on connected unit
Ground
Transmit pin on connected unit
Receive pin on connected unit
Ü DTP connector (required) — Connect transmitter DTP Out to receiver DTP In.
This cable carries: z z z z
TMDS (digital) video
Embedded audio
Bidirectional RS-232 and IR commands and data
Remote power
Signal LED — This LED lights when the unit is receiving a TMDS clock signal on the
HDMI input (transmitter) or any valid signal on the DTP In connector (receiver).
Pins:
12345678
4
5
6
1
2
3
Pin
TIA/EIA T
568 A
Wire color
White-green
Green
White-orange
Blue
TIA/EIA T
568 B
Wire color
White-orange
Orange
White-green
Blue
White-blue
Orange
White-blue
Green
7
8
White-brown
Brown
White-brown
Brown
Link LED — This LED lights a valid link is established between the units on the DTP cable.
TP Wires
á Analog Audio connector (optional) — Connect transmitter Analog Audio Out to receiver Analog Audio In. This cable carries analog audio only and is not needed for applications that do not require this audio signal.
Terminate all cable ends in accordance with the same standard, either TIA/EIA T 568 A or TIA/EIA T 568 B.
CAUTION: Do not connect these devices to a computer data or telecommunications network.
NOTES: • The DTP and Analog Audio ports are in reverse order on the receiver.
• You can check the DTP Out to DTP In cable connection as follows:
1 . Plug a cable into the DTP jack on the powered unit.
2 . Connect the opposite end of the cable into the DTP jack on the unpowered unit.
If the DTP Link LED and the Power LED on the unpowered unit are lit, the connection is correct.
DTP HDMI 301 • Setup Guide (Continued)
e HDMI Output connector (Rx) — Connect a display with an HDMI input for display of the transmitted direct digital image.
f Audio Output connector (Rx) — Connect a balanced or unbalanced stereo or mono audio device to the receiver via the Audio captive screw connector. See the drawing below.
Do not tin the wires!
Tip
Sleeve(s)
Tip
Unbalanced Stereo Output
Tip
Ring
Sleeve(s)
Tip
Ring
Balanced Stereo Output
CAUTION: Connect the sleeves to the ground contact. DO NOT connect the sleeves to the negative (-) contacts).
OUTPUTS
AUDIO
L R g Power connector — Connect an IEC power cord between the included 12 VDC power supply and a 100-240 VAC, 50-60 Hz source. Connect the power supply to either unit as shown at right.
CAUTION: This product is intended to be supplied by a Listed Power Unit marked “Class 2” or “LPS,” rated 12 VDC, 1.0 A minimum.
Always use a power supply supplied by or specified by Extron.
Use of an unauthorized power supply voids all regulatory compliance certification and may cause damage to the supply and the end product. Unless otherwise stated, the AC/DC adapters are not suitable for use in air handling spaces or in wall cavities. The installation must always be in accordance with the applicable provisions of National Electrical Code
ANSI/NFPA 70, article 75 and the Canadian Electrical Code part 1, section 16. The power supply shall not be permanently fixed to a building structure or similar structure.
Smooth
A
Ridges
A
Captive
Screw
Connector
Tie Wrap
3"
16 (5 mm) Max.
NOTE: Only one power supply is required. A single power supply connected to either unit in the pair powers both units. A power supply is included with each transmitter.
SECTION A–A
Power Supply
Output Cord
Operation
After all devices are powered up, the system is fully operational. See the definitions of the power indications (shown at right), below: a
Power LED (front panel) —
Amber — The unit is receiving power, either locally or remotely (on the DTP cable).
Green — The unit is powered on and is receiving an active HDMI signal, either on the HDMI input if a transmitter, or transmitted on the DTP cable if a receiver.
POWER
12V
0.6 A MAX
1 b
Power LED (rear panel) —
Amber — The unit is receiving power remotely (on the DTP cable).
Green — The unit is receiving power locally.
If any problems are encountered, verify that the cables are routed and connected properly. If your problems persist, call the
Extron S3 Sales and Technical Support Hotline that is closest to you, at the number shown below.
2
2
Extron USA - West
Headquarters
+800.633.9876
Inside USA/Canada
Only
+1.714.491.1500
+1.714.491.1517 FAX
Extron USA - East
+800.633.9876
Inside USA/Canada
Only
+1.919.863.1794
+1.919.863.1797 FAX
Extron Europe
+800.3987.6673
Inside Europe Only
+31.33.453.4040
+31.33.453.4050 FAX
Extron Asia
+800.7339.8766
Inside Asia Only
+65.6383.4400
+65.6383.4664 FAX
Extron Japan
+81.3.3511.7655
+81.3.3511.7656 FAX
© 2011 Extron Electronics. All rights reserved. www.extron.com
Extron China Extron Middle East
+400.883.1568
Inside China Only
+86.21.3760.1568
+86.21.3760.1566 FAX
+971.4.2991800
+971.4.2991880 FAX
68-2156-50
Rev A
07 11
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement