Avue G55IR-WB36N User manual

AVUE
Advanced Video Surveillance
G55IR-WB36N
Infrared Intelligent Vehicle PTZ Camera
User Manual
TABLE OF CONTENT
1. Notice--------------------------------------------------------------------------------------------------------1
2. Performance-----------------------------------------------------------------------------------------2
2.1 PTZ t echnology parameter --------------------- -------------- ------------------------------------------2
2.2 Camera parameter----------- ----------------------------------------- --- - ----------------------------- 2
2.3 Performance & Feature ----------- -------------------------------------- ------------------------------------- 3
3. Function and operation instruction ------------------------------------------------------------------------5
3.1 Set camera ID ------------------------------------ --- ------------ -------- ------------------------------5
3.2 Auto-run motion ----------- ---------------------- ---------- ---------- ---- -------------------------------5
3.3 Camera control ------------- ------------------------- - -- -- ----------------------------------------------------------6
3.4 Monitor function------------------- ------------------------------------ ------------------------------------------6
4. System setting------------------------------------------------------------------------------------------------8
4.1 Basic operation ------------------ -------------------------- ------ -----------------------------------------8
4.1.1 Self-testing ------- ------------------ --- ------- -- -- -------------------------------------------------8
4.1.2 Call the main menu ------------------------------------- - -------- --------------------------------8
4.1.3 The operational ways of keyboard and menu -------------------------------------------------8
4.2 Edit dome label ----------- ------------------------- ------- - -- -------------- -------------------------------------9
4.3 Display initial information ------------ ------------------------------- ---------------------------------10
4.4 Display setting --------------- ------------------------- - ------------------- -----------------------------11
4.5 System setting ------------ ------------------------- --- --------------------------------------- -----------12
4.5.1 Auto flip ------------ ------------------------- ------------------------- --------------------------- 12
4.5.2 Speed proportion pan------------- --------------------------------------------------------------- 12
4.5.3 Park action---- --------- ------------- --------------------------------------------------------------13
4.5.4 Power up action-------------- ------------------------- ---- ------------------------------------- 13
4.5.5 Fan startup by temperature-------------- ------------------------- ---- ------------------------ 13
4.5.6 Advance setting--------------------------------------------------------------------------------14
4.6 Clear ---------------- ------------------ -------- --------------- ----------------------------------------- 15
4.7 Password setup ---------------- ------------------ - ------- --------------- ------------------------------ 16
4.8 Clock setting ---------------- ------------------ - ------- --------------- -------------------------------- 17
4.9 Dome address ---------------- ------------------ - ------- --------------- -------------------------------- 18
5. Camera setting-------------- --------- ----------- -------------------------------------------------------- 19
5.1 Zoom speed------------------- ----------------------------------------------------------------------- 19
5.2 Digital zoom control ------------- --------------------------------------------------------------------2 0
5.3 Back light compensation ---------------------------------------------------------------------------21
5.4 Slow s hutter------------------------------------------------------------------------------------------22
5.5 Line Sync control----------- ------------------ ---- ------- - --------------- ---------------------------23
5.6 WDR control----------- ------------------ ---- ------- - --------------- ---------------------------------23
5.7 IR cut filter-----------------------------------------------------------------------------------------24
5.8 Advance setting ------------------------------------------------------------------------------------25
5.8.1 AE mode -------------------------------------------------------------------------------------25
5.8.2 White balance mode ---------- ---------------- ----- ----------------------------------------26
6. Function setting -------------------------------------------------------------------------------------------27
6.1 Preset ---------------------------- ------- ------- --- ------------------------------------------------------ 27
6.2 Scan -------------- --------------------------------- ------------------------------------------------------ 28
6.3 Pattern ---------------- --------------------------- --------- ----------------------------------------------29
6.4 Tour------------ --------------------- -- ------- -------------- -------------------------------------------30
6.5 Zone ---------------- ---------------------------- --- -----------------------------------------------------31
6.6 Time running---------------- ---------------------------- --- -------------------------------------------32
7. Privacy zone masking-------------------------------------------------------------------------------------33
8. Alarm function ---------------------------------------------------------------------------------------------34
9. Set language -----------------------------------------------------------------------------------------------36
10. Appendix ----------------------------------------------------------------------------------------------------37
10.1 Menu index-----------------------------------------------------------------------------------------37
10.2 24VAC Wire Diameter and Transmission Distance Comparison chart -------------------------38
10.3 Domestic and Abroad Wire Gauge Conversion Chart -------------------------------------------39
10.4 Rs485 Bus Basic Knowledge----------------------------------------------------------------------40
10.5 DIP switch setup---------------------------------------------------------------------------------------42
10.5.1 Baud rate setting------------------------------------------------------------------------42
10.5.2 Protocol setting------------------------------------------------------------------------------42
10.5.3 ID setting----------------------------------------------------------------------------------42
11.Installation instruction---------------------------------------------------------------------------------------47
11.1 Caution---------------------------------------------------------------------------------------------------47
11.2 Distributing the Line in Security-----------------------------------------------------------------------47
11.3 Lightning Proof and Surge Proof -----------------------------------------------------------------------48
11.4 Water Proof -----------------------------------------------------------------------------------------------48
11.5 The preparation of installation-------------------------------------------------------------------------48
11.6 Structure introduction-----------------------------------------------------------------------------------49
11.7 Basic size graph------------------------------------------------------------------------------------------49
11.8 Installation ----------------------------------------------------------------------------------------------50
11. 9 Cabling connection--------------------------------------------------------------------------------------51
11.10 Electrification inspection------------------------------------------------------------------------------51
12.Maintance service terms--------------------------------------------------------------------------------------52
Precaution
1. Precaution
Ø
Electrical safety
Conform to country and local electrical safety standard when using or installing the product.
Ø Transportation
The PTZ should be protected against extremes of pressure, vibration and humidity during storage
installation and transportation. The infrared PTZ camera is transported by integrated packing.
Ø
Installation of care
Please refer to user installation manual when installation. Please pick up the Infrared parts gently
and do not press it, or else, which will cause the malfunction of parts; the lens of Infrared belong to
optional products, please do not touch it by your hand to avoid scraping it.
Ø Requirements
to service personnel
All the service work should be done by qualified technicians.
Ø Do
not disassemble the pan/tilt module
Do not disassemble screws, and don't maintain the parts in the Pan/Tilt by yourself. Only qualified
and authorized personnel can undertake repairs.
Ø Environmental
requirements
= Requirements for PTZ:
Environmental temp：-40~+60 C
O
Humidity：<90%
Air pressure：86~106Kpa
AC Power supply：24V/2500MA，50/60HZ
Ø
Don't place the camera to be shoot by strong light objects
Don't place the camera to be shoot by strong light objects. Don't point the PTZ to the sun or other
bright objects when in use or not. It may affect image quality.
Ø
Function of waterproof
Our product has good water-proof, humidity-proof and dust-proof, which pass the standard of IP66.
But it's not good to stay in the humidity environment, which will make some machinery parts broken.
1
Performance
2. 1 Technology parameter
Setting:
Electrical：
AC24V
Power supply
Consumption
PTZ + Infrared light(50W)
PTZ + Searchlight(100W)
Protocol
Decoder
Built-in
Address setting
Operation:
360°continuously
Tilt rotation
Tilt180°，with auto flip
Pan0.4～80°/S
Rotation speed
Tilt0.4～60°
/S
-40 ~ + 60℃
Environmental humidity
0—95% no compensation
Surveillance
Physical:
Infrared night vision
2. 2 Camera parameter
CPS:18X
IR Cut Filter
DPS:26X
IR Cut Filter
FPS:36X
IR Cut Filter
1/4＂ Sony Exview HAD CCD
1/4＂ Sony Exview HAD CCD
NTSC： 758× 504 / PAL： 752×582
H:15.625 KHz / V:50.00 Hz
Scanning frequency
480TV Lines
NTSC：470TV Lines
PAL： 460 TV Lines
1.0 Lux
0.7Lux
18×optical， 12× digital
Focus
4.1mm-73.8mm
Angle Field of view
2.0Lux
1.4Lux
0.05 Lux
36×optical
12×digital
23×optical
12×digital
30×optical
12×digital
35×optical
12×digital
3.6mm-82.8mm
3.4mm-102mm
3.4mm-119mm
3.4mm-122.4mm
0.5 Lux
54.2°(Wide) to 2.2° (Tele) 57.8°(Wide) to1.7°(Tele) 54.0°(Wide) to 2.5° (Tele) 55.8°(Wide) to 2.0°(Tele) 55.8°(Wide) to 1.7° (Tele)
Auto/Manual
Focusing system
Auto/Manual
Auto/Manual（R/B gain adjustable）
White balance
Off/Auto
Back -light compensation
S/N ratio
More than 50dB
Electronic shutter speed 1/50 to 1/10,000s,16 steps
1/1 to 1/10,000s, 22 steps
Video output
1.0±0.2Vp-p
Video output port
Female BNC
NO
Wide Dynamic Range
2
520TV Lines
26×optical
12×digital
3.5mm-91mm
48.0°(Wide) to 2.8°(Tele)
540 TV Lines
530TV Lines
IRIS Control
Privacy zone masking
LPH:35X
IR Cut Filter
2：1 Interlace
Scanning system
Zoom
MPH:30X
IR Cut Filter
GPH:23X
IR Cut Filter
NTSC / PAL
1/4″Sony Super
HAD CCD
Effective pixel (H×V)
Minimum illumination
Above 60 meters
↓
Signal system
Resolution
Stand-up, Top-down, Wall mount
Mount
Preset、Tour、Scan、Pattern
APS：18×
Color
IP66,Weather proof housing,
4000Vlightning proof surge proof
Protection grade
128presets
Preset
Imaging element
0-254
Operational environment
7 alarm input/2 alarm output
Alarm function
Model
Sixteen protocols, including Pelco,
Kalatel, Phlips, Diamond, etc.
Environmental:
Pan rotation
Spec
2400/4800/9600/19200bps
Baud rate（RS485）
8
NTSC： 1/2 ～ 1/30,000s ， PAL： 1/1.5 ～ 1/30,000s
OFF/ON
24
8
1/2~1/30,000秒
Performance
2.3 PTZ Performance and Feature
The intelligent Pan/tilt was complete new design, compact structure, built-in constant temperature
device and rapidly heat dissipation from chip; wiper function can retain full resolution picture in raining
day; AMP socket is convenient for installation; Infrared LED range more than 60 meters; Camera rotate
flexibly with low noise, wide range capture and certain auto-functions can provide perfect quality of image
for customer.
Ø Built-in
receiver
All configurable options stored in main control board to protect against power cuts
● Integrate design and high durability
● 128 presets can be randomly stored
● 01-80preset support auto-tour, and each tour can store up to 24 presets.
● 4 pattern tours
● 4 scan
● Built-in direction indicator
● Built-in temperature indicator
● Built-in clock setting function
● Rs485 Bus communication or American Dynamics Manchester code
● Support 24 masking zones at most（This function is decide by the parameter of built-in camera, if the camera
●
has not this function, this option is invalid. )
●
7 alarm input, 2 alarm output.
Ø Pan Tilt Feature
●Aluminum alloy material and anti-violence design surface is well hidden and rapid heat removal; Level
of protection achieves IP66.
● Precise stepping motor drives the pan to run smoothly and react sensitivity.
● Integrated design, compact structure, easy to disassmeble.
● Exquisite mechanical drive, support to rotate pan 360° continuously and tilt -90 °~ + 90°, and may
rotate 180°with auto flip.
● Pan 0.4°/s to rotate slowly, and the image doesn't vibrate.
Ø Built-in
digital camera
High sensitivity, high resolution, and integrated digital processing
Auto-focus
● Auto-Iris
● Auto brightness control
● Auto white balance
● IR cut filter
● Auto back light compensation
● Auto slow shutter
●
●
Ø
OSD menu
All English menu can be selected.
Visual OSD menu. Revising the PTZ's information and parameter by keyboard and OSD menu,
and it is easy to operate.
● Set park action function and set presets, or run scan, pattern, tour, etc during idle time.
● Auto-resume movement or carry out pointed movements after power up.
●
●
3
Performance
Ø
Internal temperature test
Set time display
● When the temperature exceeds the limit, the screen will display alarm information.
● When the temperature is under the limit, the PTZ will delay to startup, and when the heat device
is heated and got higher than low limit temperature to startup.
● According to the temperature, the fan measures if it is to start or not, and prolong the life of fan.
●
Ø
Time running
By the menu “Time running”,user may set time running function everyday, and set different four
actions in four different time in one day, including preset, scan, pattern and tour.
Ø
Night View Function
Infrared LED range more than 60 meters, can manual control or auto-control infrared LED ON/OFF,
manual control through keyboard can turn infrared LED ON/OFF. If auto-control working, image color
will be switch to black and white when in low brightness, black and white will be switch to color when in
high brightness.
Ø
Wiper function
Wiper function can be set ON/OFF by calling 63 preset or OSD menu. In the raining day, the
wiper can not only ensure the high quality image, but also cleanup the dirtiness on the surface of
lens.
4
Function Instruction
3. Function Instruction
This passage mainly describes the main function and general principle of intelligence PTZ, and not
refer to the concrete operation methods. Different system platform has different operation methods, generally,
should according to the system manufactory's operation manual. Please contact dealer to get necessary
information, there are some particular requirements and operations under specific condition.
3.1 Camera ID
There are two 8-bit switch SW1 and SW2 on the commutator, and SW2 is for setting communication baud
rate and controlling protocol. (For detail setting, please refer to 10.5 DIP switch setting)
Besides the factory protocol(FACTORY), the PTZ is compatible with various popular protocols, such as
PECLO-D, PECLO-P, ERNITEC, VCL, MOLYNX, VICON, SANTACHI, PANASONIC, SAMUNG,
DIAMOND, KALATEL, LILIN, PHILIPS, VIDO B02，AD and so on.
Any controlling command must base on the objective camera address, and the camera only answer to the
controlling command address which coincide with itself. There are three kinds of camera address:
●
●
Common address: Use camera's switch number to set address 1-8 bits, the address range is 1-254.
Debug address: (Only factory protocol and PELCO can be set) if camera ID is set 0, user may select
any address to control the PTZ.
3.2 Auto-run motion
Ø
Focus/speed proportion pan
When manually adjusting, for far focus situation, the PTZ responds at a high-speed so that touching
rocker slightly may make picture move rapidly, thus cause the picture to lose. To base on humanized design,
the PTZ automatically adjust pan and tilt rotation according to zoom near and far, which make it is
convenient to operate manually to make tracking for the object. In the menu, you may change system
parameter setting proportion pan as ON to run this function.
Ø
Auto flip
If user holds the joystick in the down position, the camera rotates pan 180 degrees, then t he camera
rotates tilts up to 180 degrees . In the menu, you may set the system parameter setting AUTO FLIP as ON
to run this function.
Ø
Park action
By the menu“ park time” and “park action”, user may set auto-call preset or run tour, pattern, and
scan, etc after pointing a few minutes if the PTZ doesn't run any motions.
Ø
Power up action
By the menu“ power up action”, after the PTZ powers up or restarts, user may set auto- resume
movements before power up and auto- call preset or run tour, pattern, and scan etc .
5
Function Instruction
3. 3 Camera control
Ø Magnification control
The user can control“Wide/Tele” to adjust zoom far and near of the image by keyboard controller to obtain
panoramic image or close view that you need. The PTZ support digital zoom and optical zoom.
Ø
Focus control
System defaults Auto focus. When the lens changes, camera will auto-adjust focus according to the center of
the image to get legible image; user can also manually focus to get desire image by operating keyboard
“FAR/NEAR”. When operating keyboard joystick, camera resumes to auto focus.
The camera cannot auto focus in the following status:
●Target is not the center of the image
●Observation the target near and far at the same time, can not be clear at the same time.
●Target is a strong light object, such as neon light, spotlight , etc.
●Target moves too fast
●Target area such as wall
●Target is too dark or vague
●Target image is too small
Ø
Iris control
System defaults Auto Iris. Camera can rapidly adjust size of Iris, through the automatically induct the changing
of environment ray, and thus make the brightness of deferent image stable.
User may adjust Iris by controller keyboard “open/close” to get required brightness that you need. User also
can resume auto Iris by joystick operation. When controlling the Iris manually, the PTZ locks current position you
manually controlled; when operating joystick, the PTZ resume auto Iris.
Ø
Auto back light compensation
Camera sub-area can carry out auto back light compensation. Under a strong light background, camera will auto
compensate light for the darker object and adjust daylight to the bright background. In order to avoid making the
image lack fidelity by the back line is too bright, and the object is unable to recognize because of darkness, thus gain
legible image.
Ø
Auto white balance
Camera can automatically adjust white balance in accordance with the alteration of background lightness
to reach a true colour.
3. 4 Monitor function
Ø Set and call preset
Preset function is that PTZ stores current pan/tilt angle, zoom and other position parameters into the memory.
When necessary PTZ recalls these parameters and adjust camera to that position. User can store and recall presets
easily and promptly by using keyboard controlling. The PTZ can store up to 128 presets.
Ø
Tour
Auto tour is the built-in function in the PTZ, to make preset arranged in needful order in tour queue
by programming in advance. To make camera tour between presets by inserting presets in cruise tour. It is feasible
to program tour order, each time as you run tour, you can set the park time of preset. A tour can store 24 presets.
6
Function Instruction
Ø
Scan
The operator can prompt set right limit and left limit in advance by keyboard and menu, so as to make the
camera repeatedly scanned between right and left limit at a setting speed.
Ø
Pattern
Pattern is built-in function in camera; the PTZ can record tracks that are no less than 180s, when running
pattern, the PTZ moves repeatedly according to the recorded tracks. A PTZ can set up to 4 pattern tours.
Ø
Alarm input/output controlling function
The PTZ receive an external alarm message, to implement the action that you preset, till the alarm release to
resume, if abnormity, it will send another alarm message. The PTZ can set up to 7 alarm input and 2 alarm
output.
Ø
Privacy zone masking
The user can set a black shadow to mask the area so that it will not appear on the monitor to protect privacy.
（This function is relative with the type of the PTZ, if zoom camera hasn't this function, it is invalid)。
Ø
Lens position display
The position that the PTZ has finished to auto-checking as 0 point of pan movement and tilt movement. The pan
range is 0-360°, and tilt range is -90 °~ +90°. According to the displayed information, to set the position of camera
lens, and the position can display on the screen.
7
System Setting
4. System setting
4. 1 Basic operation
4. 1. 1 Current-carrying to PTZ and Self-testing
The PTZ conducts self-testing after current-carrying , and it rotates slowly until displaying pan origin
that is default setting, then moving to tilt origin, the lens is adjusted from far zoom to near zoom, then from
near zoom to far zoom, when self-testing is finished, there is relevant system information displaying on the
screen, as follow:
S/N of the PTZ
Soft edition
Protocol
PTZ ID
Communication parameter
The information will not disappear until you stop to operate the system. If you set“power up action”,
the PTZ will automatically activate motions after self-testing. How to operate the function? We will explain
detail introduction in following passages.
4. 1. 2 Call the main menu
The system enters into the main menu by calling 95 preset or by calling 9 preset twice within 3 seconds.
All the menu setting must enter into the main menu at first.
4. 1. 3 Menu and keyboard operation
Ø Keyboard operation:
【OPEN】 when choosing pictures, it means to increase Iris; when setting menu, it means to enter into the
next menu or setting, or means to save after setting .
【CLOSE】when choosing pictures, it means to reduce Iris; when setting menu, it means to exit without
saving setting.
【NEAR】 Focus to near
【TELE】Increase magnification
【WIDE】Reduce magnification
Joystick to up: When choosing menu, it means to choose the former one; when choosing picture, it
means camera tilt up.
Joystick to down: when choosing menu, it means to choose the next one; when choosing picture, it
means camera tilt down.
Joystick to left: when choosing menu, it is equal with【CLOSE】, when choosing picture, it means
camera tilt left .
Joystick to right: when choosing menu, it is equal with 【OPEN】, when choosing picture, it means
camera tilt right.
Press【TELE】and 【WIDE】at the same time, it means 3D joystick rotates joystick cap.
Ø
Menu operation
“BACK” : Back to the former menu
“EXIT” : Exit to menu
“ ON” : Open some setting
“OFF ” : Close some setting
8
System setting
MAIN MENU
SYSTEM SETTING
CAMERA SETTING
FUNCTION SETTING
WINDOW BLANKING
ALARMS
LANGUAGE
EXIT
4. 2 Edit dome label
When using a lot of PTZs’systems, in order to identify each PTZ,
the systems support title setting. The setting ways as follow：
1、The system enters into the main menu by calling 95 preset or by calling
9 preset twice within 3 seconds.
2、Moving joystick up and down to move the cursor to 【SYSTEM SETTING】, and pressing【OPEN】 to enter into the next menu.
3、 Moving joystick up and down to move the cursor to 【EDIT PTZ LABEL】, and pressing 【OPEN】 to enter into the label setting menu.
4、Moving joystick up/down to move the cursor to 【LABEL】, and pressing 【OPEN】 to edit current label.
SYSTEM SETTING
EDIT DOME LABEL
INITIAL INFO
DISPLAY SETUP
MOTION
CLEAR
PASSWORD SETUP
CLOCK SETTING
DOME ADDRESS
BACK
EXIT
EDIT PTZ LABEL
LABEL： SPEED DOME
5、When the cursor is twinkling in the first character of the label, to move
joystick to choose character, after editing, pressing 【OPEN】 to save.
6、Moving joystick to【 BACK】 and pressing 【OPEN】 to back to the
former menu.
The label may set 16 characters, and doesn't need editing
characters. Pressing 【OPEN】 continuously to jump over and
using spacebar to replace the deleted characters. When you finish
to edit a character, press【OPEN】 to enter into the next editing
character; when you editing the last character, pressing 【OPEN】
to save. Press 【Close】 to exit.
Characters of label available for choosing are as follow: 0- 9,
A-Z,:<>-., Space.
Other labels’ input ways are the same as above.
BACK
EXIT
9
System Setting
MAIN MENU
SYSTEM SETTING
CAMERA SETTING
FUNCTION SETTING
WINDOW BLANKING
ALARMS
LANGUAGE
EXIT
4. 3 Display initial information
1、The system enters into the main menu by calling 95 preset or by calling
9 preset twice within 3 seconds.
2、Tilt up/down joystick to 【SYSTEM SETTING】, press 【OPEN】 to
enter submenu.
3、Tilt up/down joystick to 【INITIAL INFO】, press【OPEN】 to display
initial information as below the left picture .
Initial information includes S/N of the PTZ, soft edition, Protocol, PTZ
SYSTEM SETTING
EDIT PTZ LABEL
INITIAL INFO
DISPLAY SETUP
MOTION
CLEAR
PASSWORD SETUP
CLOCK SETTING
DOME ADDRESS
BACK
EXIT
INITIAL INFO
S/N:5DSAD7B24500000
FIRM WARE
V1.60
PROTOCOL： FACTORY
PTZ ADDRESS：001
COMM：4800,N,8,1
BACK
EXIT
10
ID, communication parameter. System setting may change the numerical
value of initial information.
System setting
MAIN MENU
SYSTEM SETTING
CAMERA SETTING
FUNCTION SETTING
WINDOW BLANKING
ALARMS
LANGUAGE
EXIT
SYSTEM SETTING
EDIT PTZ LABEL
INITIAL INFO
DISPLAY SETUP
MOTION
CLEAR
PASSWORD SETUP
CLOCK SETTING
DOME ADDRESS
BACK
EXIT
DISPLAY SETUP
PTZ LABEL
OFF
PRESET LABEL
OFF
ZOOM LABEL
ON
ZONE LABEL
OFF
DIRECTION LABEL
ON
TEMPERATURE LABEL OFF
TIME LABEL
ON
DATE LABEL
ON
BACK
EXIT
4. 4 Display setup
1、The system enters into the main menu by calling 95 preset or by calling
9 preset twice within 3 seconds.
2、Tilt up/down joystick to 【SYSTEM SETTING】, press 【OPEN】 to
enter submenu.
3、Tilt up/down joystick to【DISPLAY SETUP】, press 【OPEN】to enter
“display setup” menu, May setting the content of the display setup as
follow:
● 【DOME LABEL】
● 【PRESET LABEL】
● 【ZOOM LABEL】
● 【ZONE LABEL】
● 【DIRECTION LABEL】
● 【TEMPERATURE LABEL】
● 【TIME LABEL】
● 【DATE LABEL】
4、 Taking display PTZ label as an example to explain the operation process. Tilt up/down joystick to move cursor to 【Dome LABEL OFF】, press
【OPEN】, there is a sign “ ” besides【Dome LABEL】, the cursor is
twinkling besides 【OFF】, as left picture shows;
5、Joystick tilt up/down, setting number changes between ON/OFF, when
setting 【ON】, it means to display“PTZ label”; when setting 【OFF】,
it means not to display “PTZ label”.when p ressing 【 OPEN】, the cursor
jump back in front of 【DOME LABEL】, means label setting is finished,
when moving the cursor to 【EXIT】, it means exiting the menu setting.
The displaying information on the screen will change with the PTZ
rotation; Through the information on the screen, user can see current PTZ
inside temperature, magnification, display zone etc. When all the label are
displayed, the PTZ works as the following picture shows,:
(In the picture “305” means pan angle, “45” means tilt angle. )
PTZ label
Preset setting
Zone label
Direction label
Temperature label
07/12/06
17:39:10
Date label
Time label
Zoom magnification label
11
System Setting
MAIN MENU
SYSTEM SETTING
CAMERA SETTING
FUNCTION SETTING
WINDOW BLANKING
ALARMS
LANGUAGE
EXIT
4. 5 Systematic motion control
Systematic motion controlling may control a series of canonical movement of the PTZ, and play an important role in controlling the PTZ.
1、The system enters into the main menu by calling 95 preset or by calling
9 preset twice within 3 seconds.
2、Tilt up/down joystick to【SYSTEM SETTING】, press【OPEN】to enter submenu.
3、Tilt up/down joystick to 【MOTION】, press 【OPEN】 to enter systematic motion controlling menu, as left picture shows.
SYSTEM SETTING
EDIT PTZ LABEL
INITIAL INFO
DISPLAY SETUP
MOTION
CLEAR
PASSWORD SETUP
CLOCK SETTING
DOME ADDRESS
BACK
EXIT
4. 5. 1 Auto flip
1、Operate joystick, move the cursor to【AUTO FLIP】: press 【OPEN】
to enter“ auto flip ”setting, tilt up/down joystick, for example: choosing
"ON" to open“ auto flip”; choosing "OFF" to close“auto flip”.
Press 【OPEN】 to save .
REMARK: When opening the auto flip function, user holds the joystick
in the down position, the camera rotates pan 180 degrees, after the camera
rotates tilt up to 180 degrees.
4. 5. 2 Speed proportion pan
MOTION
AUTO FLIP
ON
PROPORTION PAN ON
PARK TIME
005
PARK ACTION
SCAN
POWER UP ACTION AUTO
FAN ENABLED
040
TEMP C/F
CENT
ADVANCE SETTING
BACK
EXIT
12
1. Operate joystick, move the cursor to【PROPORTIONAL PAN】; press
【OPEN】 to enter“ proportion pan” setting, tilt up/down joystick to choose, if choosing 【ON】, it means to open proportion pan; if choosing
【OFF】, it means to close proportion pan , press 【OPEN】to save.
OPERATION KNACKS
When manually adjusting, for far focus situation, the PTZ
responds at a high-speed so that touching joystick slightly may
make picture move rapidly, thus cause the picture to lose. To
base on humanized design, the PTZ automatically adjust pan
and tilt rotation according to zoom near and far, which make it
is convenient to operate manually run after object.
System setting
4. 5. 3 Park action
MOTION
AUTO FLIP
ON
PROPORTION PAN ON
PARK TIME
005
PARK ACTION
SCAN
POWER UP ACTION AUTO
FAN ENABLED
040
TEMP C/F
CENT
ADVANCE SETTING
BACK
EXIT
This setting allows the PTZ to run an appointed action after it enters
vacancy for a few time (1-240minutes). If default sets as 0, it means not to
run this action automatically.
1、 Operate joystick, move the cursor to 【PARK TIME】, press 【OPEN】
to tilt up/down joystick to set park time, the range is 0-240 (minute), press
【OPEN】 to save.【PARK ACTON】 is running action at park time, when
【PARK TIME】 sets as 0, this item can't be set.
2、Operate joystick, move the cursor to 【PARK ACTON】, press 【OPEN】
there will be a sign
in the front of 【PARK ACTON】, the cursor jump
to right, after tilt up/down joystick to choose“ park action” ，there are
options for choosing as follow, press 【OPEN】 to save.
● 【NONE】- (default) none action
● 【PRESET】 - use preset 1-80
● 【SCAN】 - run scan
● 【PAT1】 - run pattern X
● 【TOUR】 - run tour
MOTION
AUTO FLIP
ON
PROPORTION PAN ON
PARK TIME
005
PARK ACTION
SCAN
POWER UP ACTION AUTO
FAN ENABLED
040
TEMP C/F
CENT
ADVANCE SETTING
BACK
EXIT
MOTION
AUTO FLIP
ON
PROPORTION PAN ON
PARK TIME
005
PARK ACTION
SCAN
POWER UP ACTION AUTO
FAN ENABLED
040
TEMP C/F
CENT
ADVANCE SETTING
BACK
EXIT
4. 5. 4 Power up action
The PTZ start to run actions after self-testing, if nobody intervenes
it , it will repeatedly run this action continuously , if default sets as
【NONE】.
1. Operate joystick, move the cursor to 【POWER UP ACTION】: press
【OPEN】 to jump to the following choice, tilt up/down joystick to choose
“power up action”, press 【OPEN】 to save.
● 【NONE】 - none action
● 【AUTO】 - the PTZ resumes the primary action and direction
before power up.
● 【PRESET】 - use preset 1
● 【SCAN】 - run scan
● 【PAT1】 - run pattern
● 【TOUR】 - run tour
4. 5. 5
Fan startup by temperature
The temperature of the PTZ will rise when it is in high temperature. The
fan will open automatically when the temperature reaches to a very high degree
value in order to make sure the stability of the PTZ.
Operate joystick, move the cursor to 【FAN ENABLED】: press【OPEN】 , the cursor will skip to the back option. The user can choose the fan
to start up temperature, and press【OPEN】 to save it in actual condition.
The default setting temperature of the fan startup is 40 C. The user
also can enter into the fan startup setting to adjust the temperature of fan
O
startup. As picture shows: the temperature range is 0-60 C.【TEMP】can
switch the temperature between fahrenheit and centigrade.
O
13
System Setting
4.5.6 Advance setting
MOTION
AUTO FLIP
ON
PROPORTION PAN ON
PARK TIME
005
PARK ACTION
SCAN1
POWER UP ACTION AUTO
FAN ENABLED
040
TEMP
CENT
ADVANCE SETTING
BACK
EXIT
ADVANCE SETTING
EIS ENABLED
N/A
PRESET FREEZE
N/A
HEAD-DOWN ON/OFF
DEFOGGER
10
A D J SPEED
100
WIPER
IR HEADLIGHT
BACK
EXIT
1.Operate joystick and move to【ADVANCE SETTING】, press【OPEN】
to enter into "advance setting";
【EIS ENABLED】: Electronic Image Stabilizer function;
【PRESET FREEZE】: Function of Preset Freeze means during
calling presets, the monitor displays the image before call presets, and
releases the freeze image when camera arrives the appointed presets.
【HEAD-DOWN】: Settings of Top/Down. “O N ” means DOWN,
“O FF ” means TOP.
【DEFOGGER】: Lens of PTZ will be fogged when PTZ works in
quite cold temperature. In order to get clear image, defogger will open
automatically at the appointed temperature. Choosing 【DEFOGGED】by
operating the joystick, and press 【OPEN】, then cursor leap to the optional.
Choose the temperature to run the defogger, and press 【OPEN】to save.
Range of Temperature: 0~30℃.
【ADJ SPEED】：The rotation percentage of P/T, 100 means factory
speed, 80 means 80% of factory speed.
【WIPER】: Wiper runs by calling 63 Preset.
【MODE】: Setting of Infrared light. Call 62 preset to run Infrared light
under the setting of【MANUAL】. Save 62 preset to close the infrared.
【DELAY TIME】: Setting the auto close time of IR light, ranging from
1-240 Minutes.【IR Cut Filter】:Setting the imaging model after the IR light
as ON, three modes for choice: Auto, Color, Black.
【ACTIVATE AUX1】Whether to link AUX 1 when open the IR light,
“ON” means Link. “OFF” means not to link.
【Auto】 is invalid as it's searchlight, it must be
controlled under【Manual】status.
【LED 1】For LED brightness adjustment, range:50-200, Brightness
increase in proportion as bigger digits is chosen.
LED 1
【LED 2】Same as the above
【LED 3】Temporarily unavailable
L ED 2
【LIGHT】Options of light sources
(Temporarily unavailable)
IR HEADLIGHT
MODE
DELAY TIME
BW
ACT. AUX1
LED 1
LED 2
LED 3
LIGHT
BACK
EXIT
14
MID
002
AUTO
OFF
100
200
×
×
OPERATION KNACKS
1.After the PTZ set the EIS function, if the PTZ wobble slight when running,
the camera will shield the wobble picture and make the picture calm and smooth.
2.When start-up preset freeze, it can eliminate the sense of flash caused by
calling presets when open function of Preset Freeze, which can reduce the
storage space of DVR if image is stored by DVR.
These function in the advance setting menu depends on the models and
parameters of built-in camera in PTZ, if the camera haven't this function,
then this function is invalid.
The option is useless (N/A) when the camera module has no such function.
System setting
MAIN MENU
SYSTEM SETTING
CAMERA SETTING
FUNCTION SETTING
WINDOW BLANKING
ALARMS
LANGUAGE
EXIT
4. 6 Clear and restart
1、The system enters into the main menu by calling 95 preset or by calling
9 preset twice within 3 seconds.
2、Tilt up/down joystick to 【SYSTEM SETTING】, press 【OPEN】to
enter submenu.
3、Tilt up/down joystick to 【CLEAR】, press 【OPEN】to enter submenu,
as left picture shows.
● 【CLEAR ALL ZONES】
● 【CLEAR ALL PRESETS】
● 【CLEAR ALL PATTERNS】
● 【CLEAR ALL TOURS】
SYSTEM SETTING
● 【CLEAR ALL WINDOWS】
EDIT PTZ LABEL
INITIAL INFO
DISPLAY SETUP
MOTION
CLEAR
PASSWORD SETUP
CLOCK SETTING
DOME ADDRESS
BACK
EXIT
● 【FACTORY DEFAULTS】: resume the factory default. Run this funct-
CLEAR
CLEAR ALL ZONES
CLEAR ALL PRESETS
CLEAR ALL PATTERNS
CLEAR ALL TOURS
CLEAR ALL WINDOWS
FACTORY DEFAULTS
RESTART
BACK
EXIT
ion, the camera parameter and system parameter will resume to factory default,
clear all windows and alarm setting. Please be cautious to use this function .
● 【RESTART】
4、Set clear zone as an example to explain the process. Tilt up/down joystick to 【CLEAR ALL ZONES】, press【OPEN】to clear all zones.
Once clear all commands in the controlling menu,
it cann't resume, so please be careful of using it.
15
System Setting
MAIN MENU
SYSTEM SETTING
CAMERA SETTING
FUNCTION SETTING
WINDOW BLANKING
ALARMS
LANGUAGE
EXIT
4.7 Password set
1. The system enters into the main menu by calling 95 preset or by calling 9
preset twice within 3 seconds.
2. Operate the joystick up and down, move the cursor to 【SYSTEM
SETTING】 , press 【OPEN】 to call the submenu.
3. Operate the joystick up and down , move the cursor to 【PASSWORD
SETUP】, press 【OPEN】 to call the submenu. Please refer to the left
picture.
4. Operate the joystick up and down , move the cursor to 【OLD
SYSTEM SETTING
EDIT PTZ LABEL
INITIAL INFO
DISPLAY SETUP
MOTION
CLEAR
PASSWORD SETUP
CLOCK SETTING
DOME ADDRESS
BACK
EXIT
PASSWORD】, press 【OPEN 】to choose it, operate the joystick right and
left to input the password, Tilt up and down to choose the number which you
need.
● 【NEW PASSWORD】 Enter the new password
● 【CONFIRM PASSWORD 】 Confirm the new password
● 【ENABLE PASSWORD 】Set PASSWORD off / on
(The password function is noneffective under the PASSWORD OFF.) It
means that users can enter into the main menu without password. (The password
function is effective under the password ON.) It means that user enter into
the main menu with password.
PASSWORD SETUP
OLD PASSWORD：******
NEW PASSWORD：******
16
CONF PASSWORD：******
When user forgot the password and can not enter into the
ENABLE PASSWORD：OFF
BACK
main menu, he can use the super password to enter ,which
is "892226"，At this time ,the password of PTZ will
EXIT
change to initial one, which is "000000",and then user may
set the password by himself again.
System setting
MAIN MENU
SYSTEM SETTING
CAMERA SETTING
FUNCTION SETTING
WINDOW BLANKING
ALARMS
LANGUAGE
EXIT
4.8 Time set
1. The system enters into the main menu by calling 95 preset or by calling 9
preset twice within 3 seconds.
2. Operate the joystick up and down, move the cursor to 【SYSTEM
SETTING】 , press 【OPEN】 to call the submenu.
3. Operate the joystick up and down, move the cursor to 【CLOCK
SETTING】 , press【 OPEN 】to call the submenu. Please refer to the left
picture.
4. Operate the joystick up and down, move the cursor to【TIME】, press
SYSTEM SETTING
EDIT PTZ LABEL
INITIAL INFO
DISPLAY SETUP
MOTION
CLEAR
PASSWORD SETUP
CLOCK SETTING
DOME ADDRESS
BACK
EXIT
【 OPEN】 to choose it, move the joystick up and down to choose the
number you need, move the joystick right and left to set hour, minute,
second.
● 【DATE】set year, month, date;
● 【DAY】 set week;
● 【BACK】return to the former menu;
● 【EXIT】 exit the main menu.
CLOCK SETTING
TIME
03:20:18
DATE
07:10:10
DAY
WED
BACK
EXIT
17
System Setting
MAIN MENU
SYSTEM SETTING
CAMERA SETTING
FUNCTION SETTING
WINDOW BLANKING
ALARMS
LANGUAGE
EXIT
4.9 DOME Address Setting
1.The system enters into the main menu by calling 95 preset or by calling 9
preset twice within 3 seconds.
2.Tilt up/down the joystick and move the cursor to【SYSTEM
SETTING】, press【OPEN】 to enter submenu.
3.Tilt up/down the joystick and move the cursor to【DOME ADDRESS】,
press【OPEN】 to call dome parameter setting menu
.
S/N : Series No. of the dome
CONF : Confirm S/N and input the same NO. with S/N
DOME ADDRESS : Set dome address (ID range: 001-255)
SYSTEM SETTING
EDIT PTZ LABEL
INITIAL INFO
DISPLAY SETUP
MOTION
CLEAR
PA SSWORD SETUP
CLOCK SETTING
DOME ADDRESS
BACK
EXIT
1.If 【S/N】 and 【CONF】 are different, the above operation
can't be implemented.
2.The PTZ address should be set as 255 (mean set Switch
1 as ON), there will be display this item 【PTZ ADDRESS】
3.After setting PTZ address, the PTZ need to restart, then
the PTZ address will be effective.
CLOCK SETTING
TIME
03:20:18
DATE
07:10:10
DAY
WED
BACK
EXIT
18
Camera setting
MAIN MENU
SYSTEM SETTING
CAMERA SETTING
FUNCTION SETTING
WINDOW BLANKING
ALARMS
LANGUAGE
EXIT
5. Camera setting
5. 1 Zoom speed
1、The system enters into the main menu by calling 95 preset or by calling 9
preset twice within 3 seconds.
2、Tilt up/down joystick to【CAMERA SETTING】 , press 【OPEN】to
enter submenu；
3、 Operate joystick, move the cursor to 【ZOOM SPEED】; press【OPEN】
will appear a sign "
" in the front of 【ZOOM SPEED】, the cursor moves to
right, tilt up/down joystick to choose 【HIGH】 or 【LOW】 ；
CAMERA SETTING
ZOOM SPEED
HIGH
DIGITAL ZOOM
ON
BLC MODE
OFF
SLOW SHUTTER
ON
LINE SYNC
OFF
WDR MODE
ON
ADVANCE SETTING1
ADVANCE SETTING2
BACK
EXIT
4、 Press 【OPEN】 to save, press 【CLOSE】 to cancel.
19
Camera Setting
MAIN MENU
SYSTEM SETTING
CAMERA SETTING
FUNCTION SETTING
WINDOW BLANKING
ALARMS
LANGUAGE
EXIT
5. 2 Digital zoom control
1、The system enters into the main menu by calling 95 preset or by calling
9 preset twice within 3 seconds.
2、Tilt up/down joystick to 【CAMERA SETTING】, press 【OPEN】 to
enter camera setting;
3、Operate joystick, move the cursor to 【DIGITAL ZOOM】, press 【OPEN】 to enter digital zoom setting, tilt up/down joystick, to choose ON means
open digital zoom control which is digital zoom is pulled near, if pulling the
digital zoom near again, the PTZ enters into“ digital zoom increase”; to
choose OFF means to close digital zoom control .
CAMERA SETTING
ZOOM SPEED
HIGH
DIGITAL ZOOM
ON
BLC MODE
OFF
SLOW SHUTTER
ON
LINE SYNC
OFF
WDR MODE
ON
ADVANCE SETTING1
ADVANCE SETTING2
BACK
EXIT
20
4、Press【OPEN】 to save.
OPERATION KNACKS
When digital zoom be set as ON, the maximum zoom magnification of the PTZ is digital zoom magnification times optical
zoom magnification; when digital zoom be set as OFF, the maximum
zoom magnification of the PTZ is optical zoom magnification.
The option of the digital zoom is ON/OFF when the
camera module is SONY 、LG、CNB、HITACHI .
Camera setting
MAIN MENU
SYSTEM SETTING
CAMERA SETTING
FUNCTION SETTING
WINDOW BLANKING
ALARMS
LANGUAGE
EXIT
5. 3 Back light compensation
1、The system enters into the main menu by calling 95 preset or by calling 9
preset twice within 3 seconds.
2、Operate joystick, move the cursor to 【CAMERA SETTING】 to enter
submenu.
3、Operate joystick, move the cursor to 【BLC MODE】, press 【OPEN】,
There will be a sign
in the front of【BLC MODE】, the cursor jump to
right, tilt joystick to open or close back light compensation function. If choosing ON means to open back light compensation mode; if choosing OFF means to close back light compensation mode;
CAMERA SETTING
ZOOM SPEED
HIGH
DIGITAL ZOOM
ON
BLC MODE
OFF
SLOW SHUTTER
ON
LINE SYNC
OFF
WDR MODE
ON
ADVANCE SETTING1
ADVANCE SETTING2
BACK
EXIT
4、Press 【OPEN】 to save.
OPERATION KNACKS
Strong background ray can make backlighting objects engender
shadow, (back light compensation), the PTZ can auto-adjust iris to
match with the changes of various ray, and auto-revise the main
lightness to make the pictures more legible.
This function relates to models and parameters of the built-in
camera in the PTZ, when open black compensation, it has two
functions which are auto-adjust (when you choose ON) or
manual adjust(0-255) according to the different of the camera.
Non-use back light compensation, in
strong sunshine, the back light side is
subject to dark.
Use back light compensation, the
image is in gear.
21
Camera Setting
MAIN MENU
SYSTEM SETTING
CAMERA SETTING
FUNCTION SETTING
WINDOW BLANKING
ALARMS
LANGUAGE
EXIT
5. 4 Slow shutter control
1、The system enters into the main menu by calling 95 preset or by calling
9 preset twice within 3 seconds.
2、Operate joystick, move the cursor to【CAMERA SETTING】 to enter
submenu.
3、Operate joystick, move the cursor to【SLOW SHUTTER】, press
【OPEN】, there will be a sign
in the front of 【SLOW SHUTTER】,
the cursor moves to right, tilt up/down joystick to “slow shutter” choice,
if choosing ON means to open slow shutter function, if choosing OFF means
close “slow shutter”function.
CAMERA SETTING
ZOOM SPEED
HIGH
DIGITAL ZOOM
ON
BLC MODE
OFF
SLOW SHUTTER
ON
LINE SYNC
OFF
WDR MODE
ON
ADVANCE SETTING1
ADVANCE SETTING2
BACK
EXIT
22
4、Press【OPEN】to save.
OPERATION KNACKS
When the PTZ monitors at night or dark environment, because
the ray is not enough, the image on the screen is too dark, setting slow
shutter can lengthen the time of lighting so that make the picture that
is shooted in dark more legible.
This function depends on the models and parameters of built-in
camera in PTZ, if the camera haven't this function, then this
function is invalid.
Camera setting
MAIN MENU
SYSTEM SETTING
CAMERA SETTING
FUNCTION SETTING
WINDOW BLANKING
ALARMS
LANGUAGE
EXIT
5. 5 Line sync control
1、The system enters into the main menu by calling 95 preset or by calling
9 preset twice within 3 seconds.
2、Operate joystick, move the cursor to 【CAMERA SETTING】, press
【OPEN】 to enter submenu.
3、Operate joystick, move the cursor to 【LINE SYNC】; press 【OPEN】,
tilt up/down joystick to set line sync. Line sync can divide two kinds: internal/external, choose OFF is internal sync; choose ON is external sync;
press 【OPEN】 to save .
OPERATION KNACKS
CAMERA SETTING
ZOOM SPEED
HIGH
DIGITAL ZOOM
ON
BLC MODE
OFF
SLOW SHUTTER
ON
LINE SYNC
OFF
WDR MODE
ON
ADVANCE SETTING1
ADVANCE SETTING2
BACK
EXIT
CAMERA SETTING
ZOOM SPEED
HIGH
DIGITAL ZOOM
ON
BLC MODE
OFF
SLOW SHUTTER
ON
LINE SYNC
OFF
WDR MODE
ON
ADVANCE SETTING1
ADVANCE SETTING2
BACK
EXIT
When a lot of PTZs use a line in the same time, if the image is
twinkling as switching, please set each PTZ as external line and
adjust the numerical value of external line.
This function is relative with the model and parameter of
the camera module which insert in the PTZ. The option
is useless(N/A) when the camera module has no such
function.
5. 6 WDR Control
1、Operate joystick, move the cursor to 【WDR MODE】,press 【OPEN】,
tilt up/down joystick to set WDR; Choose ON means open WDR, choose
OFF means close WDR, Press 【OPEN】 to save.
【WDR MODE】: WDR is the function that features of image can be
captured clearly by camera while the picture was cover with strong
contrast background. For example: you can enable WDR function to
sublime image quality when the two areas A and B exist simultaneously,
A: High Intensity area under strong light exposure (source from
daylight, lamp and so on), B: Low luminance area, like shadow,
backlighting zone and so on.
This function is relative with the model and parameter
of the camera module which insert in the PTZ. The
option is useless(N/A)when the camera module has no
such function.
23
Camera Setting
MAIN MENU
SYSTEM SETTING
CAMERA SETTING
FUNCTION SETTING
WINDOW BLANKING
ALARMS
LANGUAGE
EXIT
5. 7 IR cut filter
1、The system enters into the main menu by calling 95 preset or by
calling 9 preset twice within 3 seconds.
2、Operate joystick, move the cursor to 【CAMERA SETTING】 to
enter submenu.
3、 Operate joystick, move the cursor to 【ADVANCE SETTING1】;
press 【OPEN】, there will be a sign
in the front of【ADVANCE
SETTING1】, the cursor jumps to right, move joystick to“ IR cut filter”,
choices as follow, 【AUTO】is default.
● 【AUTO】IR cut filter mode, it means the PTZ automatically
transfers according to sensitivity.
● 【COLOR 】set as color mode
● 【BLACK】 set as black and white mode
CAMERA SETTING
ZOOM SPEED
HIGH
DIGITAL ZOOM
ON
BLC MODE
OFF
SLOW SHUTTER
ON
LINE SYNC
OFF
WDR MODE
ON
ADVANCE SETTING1
ADVANCE SETTING2
BACK
EXIT
● 【TIME】 set ON time and OFF time of black and white mode
4、Press 【OPEN】 to save.
When user choose 【TIME】, 【IR CUT ON TIME 】and 【IR
CUT OFF TIME】will be effective. User may set ON time and OFF
time of black and white mode, as follow:
1.Operate joystick, move the cursor to 【IR CUT FILTER】, tilt up/down
joystick to choose【 TIME】 mode, press 【OPEN】to save;
2.Operate joystick, move the cursor to【 IR CUT FILTER】, tilt up/down
joystick to set the beginning time of black and white mode; move joystick
to【IR CUT OFF TIME】 to set the finish time of black and white mode,
the same as setting the beginning time;【FLIP】: 180° inversion imaging
function of image, 【MIRROR】: image mirroring function.
3 .Operate the joystick and move the cursor to【 MAX GAIN】 which is
the max limits of automatic gain and ranges from 8 to 28dB. As the ray
ADVANCE SETTING 1
IR CUT FILTER
AUTO
IR CUT ON TIME N/A
IR CUT OFF TIME N/A
THRESHOLD
10dB
FLIP
OFF
MIRROR
OFF
MAX GAIN
08dB
EXPOSURECOMP OFF
BACK
EXIT
is dark, the more smaller value of 【MAX GAIN】, the more darker, the
noise of image is less; The more bigger value of 【MAX GAIN】, the more
brighter, but the noise of image is much.
4.【THRESHOLD】:sensitive of IR cut filter, the range from 0 to 28dB.
5.【EXPOSRUECOMP】:exposure compensation function.
6. Press【 OPEN 】to save.
OPERATION KNACKS
IR cut filter function uses color in day; use black and white at
night. This function not only guarantees the quality of image, but
also saves the room of storage.
This function depends on the models and parameters
of built-in camera in PTZ, if the camera haven't this
function, then this function is invalid.(N/A)
24
Camera setting
MAIN MENU
SYSTEM SETTING
CAMERA SETTING
FUNCTION SETTING
WINDOW BLANKING
ALARMS
LANGUAGE
EXIT
5. 8 Advance setting 2
1、The system enters into the main menu by calling 95 preset or by calling
9 preset twice within 3 seconds.
2、Operate joystick, move the cursor to 【CAMERA SETTING】 to enter
submenu.
3、Operate joystick, move the cursor to 【ADVANCE SETTING2】; press
【OPEN】 to enter submenu, as left picture shows;
5. 8 . 1 AE mode
CAMERA SETTING
ZOOM SPEED
HIGH
DIGITAL ZOOM
ON
BLC MODE
OFF
SLOW SHUTTER
ON
LINE SYNC
OFF
WDR MODE
ON
ADVANCE SETTING1
ADVANCE SETTING2
BACK
EXIT
1、Operate joystick, move the cursor to 【AE MODE】, press 【OPEN】,
tilt up/down joystick to choose AE mode, modes for choosing as follow:
● 【AUTO 】: default setting, auto Iris mode
● 【BRIGHT】: brightness priority mode
● 【IRIS】: iris priority mode
● 【SHUTTER】 : shutter priority mode
2、Choose Iris priority mode 【IRIS】, press 【OPEN】to save.
3、Move joystick to the sub-choices of AE mode 【IRIS F1.4】, press
【OPEN】 to choose adequate Iris, press 【OPEN】 to save.
1/50】it means shutter speed, when AE mode is shutter
● 【 SHUTTER
priority, this function can be set.
F1.4】 it means the size of iris, when AE mode is iris
● 【 IRIS
priority, this function can be set.
F2.0/ODB】it means brightness, when AE mode is brigh● 【BRIGHT
tness priority, this function can be set.
OPERATION KNACKS
ADVANCE SETTING2
AE MODE
AUTO
SHUTTER
N/A
IRIS
N/A
BRIGHT
N/A
BW MODE
AUTO
R GAIN
N/A
B GAIN
N/A
HI-RESOLUTION
ON
BACK
EXIT
Quality of photo relates to exposure amount, that is to say how
much light can make CCD receives legible image. Exposure
amount is relative to the time of lighten (be up to shutter speed)
and the area of lighten (be up to the size of iris).
The camera can automatically calculate suitable exposure amount according to brightness of scenery and CCD sensitivity, in the situation that the
exposure amount is certain: 【SHUTTER】 (shutter priority) is to fix shutter
speed, the camera will auto decide to use how much iris; 【IRIS】(iris priority) is to fix the size of iris, and auto-decide to use shutter speed. 【BRIGHT】
(brightness priority)is point that the camera TTL check the light directly and
control the brightness of image.
25
Camera Setting
MAIN MENU
SYSTEM SETTING
CAMERA SETTING
FUNCTION SETTING
WINDOW BLANKING
ALARMS
LANGUAGE
EXIT
5. 8. 2 White balance mode
System supports 【AUTO】 、indoor mode 【INDOOR】 、outdoor
mode 【OUTDOOR】 、auto track mode 【ATW 】 、single mode 【OPW】 、
【OPT】 mode、manual mode【MANUAL】 and kinds of white balance
modes, etc. Detail setting as follow:
1、The system enters into the main menu by calling 95 preset or by calling
9 preset twice within 3 seconds. click each command enter into“ advanced
setting2” menu according to the order in left picture .
2、Operate joystick, move the cursor to【BW MODE】 to choose white
CAMERA SETTING
ZOOM SPEED
HIGH
DIGITAL ZOOM
ON
BLC MODE
OFF
SLOW SHUTTER
ON
LINE SYNC
OFF
WDR MODE
ON
ADVANCE SETTING1
ADVANCE SETTING2
BACK
EXIT
balance mode, press 【OPEN】 to save.
Auto mode 【AUTO】 is the default mode of speed PTZ, which is autorevert real color after the white balance sensor check the environment by
camera. When choosing manual mode【MANUAL】, adjust the numerical
value of 【R GAIN】and【B GAIN】.
●
【R GAIN】t he range is 1-225; the numerical value is bigger, it means
that adding red is more, the tone changes to be warm.
●
【B GAIN】the range is 1-225; the numerical value is bigger, it means
that adding green is more, the tone changes to be cold.
Indoor mode 【INDOOR】, and the tone leans to cold.
Outdoor mode 【OUTDOOR】, and the tone leans to warm.
【HI-RESOLUTION】high resolution is built-in function of camera ,This
ADVANCE SETTING2
AE MODE
AUTO
SHUTTER
N/A
N/A
IRIS
BRIGHT
N/A
BW MODE
AUTO
N/A
R GAIN
N/A
B GAIN
HI-RESOLUTION
ON
BACK
EXIT
26
function is relative with the model of camera.
It is possible that different camera has not the setting of
【INDOOR】,【OUTDOOR】,【HI-RESOLUTION】;
That means the current camera has no such function when
the setting option shows N/A.
Function setting
6. Function setting
MAIN MENU
SYSTEM SETTING
CAMERA SETTING
FUNCTION SETTING
WINDOW BLANKING
ALARMS
LANGUAGE
EXIT
FUNCTION SETTING
PRESETS
SCAN
PATTERNS
TOUR
ZONES
TIME RUNNING
BACK
EXIT
6. 1 Preset
1、The system enters into the main menu by calling 95 preset or by calling
9 preset twice within 3 seconds. Click each command to enter“ preset menu” according to the order of the left picture. As following:
【PRESET NUMBER】
● 【 SET PRESET】
● 【 SHOW PRESET】
● 【 CLEAR PRESET】
● 【 EDIT PRESET LABEL】
Define preset and call preset function can be set by keyboard operation, input preset number at first, then click the key“save /call preset”to
carry out.
●
2、Define current preset number: move the cursor to 【PRESET N UMBER】,press 【OPEN】 to choose preset number, the range is 01-128as the
left picture show, here chooses number 5 as current preset, the following
operations aim at the current preset.
3、Define current preset: move the cursor to 【SET PRESET】,press
【OPEN】, by operating joystick to adjust magnification, to choose good
objective image, press 【OPEN】 to save. If the image is very near, the Image is belong in digital zoom; when setting preset, the image will jump to
maximal optical zoom.
OPERATION KNACKS
PRESETS
PRESET NUMBER
05
SET PRESET
SHOW PRESET
CLEAR PRESET
EDIT PRESET LABEL
BACK
EXIT
Preset function is that PTZ stores current pan/tilt angle, zoom
and other position parameters into the memory. When necessary PTZ
recalls these parameters and adjust camera to that position.
4、Display current preset: move the cursor to 【SHOW PRESET】, press
【OPEN】, the screen will display the current preset;
5、Clear current preset: move the cursor to 【CLEAR PRESET】, press
【OPEN】, the current preset is cleared.
6、Edit current preset label: move the cursor to【EDIT PRESET LABEL】,
press 【OPEN】 to enter into editing preset submenu, system auto-sets label as PRESET-XX, press 【OPEN】 to revise label.
EDIT PRESET LABEL
LABEL：PRESET-05
BACK
EXIT
1.When running to program, display, clear preset and edit label,
should choose preset number at first.
2. The label may set up to 16 characters, and doesn't need editing
characters. Press 【OPEN】 continuously to jump over and use
spacebar to replace the deleted characters.
When you finish to edit a character, press 【OPEN】 to enter
into the next editing character;
when you finish to edit the last character, pressing 【OPEN】
to save. Press 【CLOSE】 to exit. Character of label is suitable for
choosing as follow: 0-9、A-Z、:<>-. , space.
27
Function setting
MAIN MENU
SYSTEM SETTING
CAMERA SETTING
FUNCTION SETTING
WINDOW BLANKING
ALARMS
LANGUAGE
EXIT
6. 2 Scan
Scan is that preset two points , then the camera repeatedly scan between the two points at a stable speed, the same magnification and pan. A dome has four scan tour.
1、The system enters into the main menu by calling 95 preset or by calling
9 preset twice within 3 seconds. click menu to enter “scan” menu, as the
left picture shows.
● 【SCAN NUMBER】
● 【SCAN SPEED 】
● 【SET LEFT LIMIT】
● 【SET RIGHT LIMIT】
FUNCTION SETTING
PRESETS
SCAN
PATTERNS
TOUR
ZONES
TIME RUNNING
BACK
EXIT
SCAN
SCAN NUMBER
04
SCAN SPEED
50
SET LEFT LIMIT
SET RIGHT LIMIT
RUN SCAN
CLEAR SCAN
EDIT SCAN LABEL
BACK
EXIT
● 【RUN SCAN】
● 【CLEAR SCAN】
● 【EDIT SCAN LABEL】
2、Define current scan number: operate joystick ,move the cursor to 【SCAN
NUMBER】,press 【OPEN】 ,tilt up/downjoystick to choose scan number,
press 【OPEN】to save .the following operations aim at the current scan
number.
3、Scan speed setting: operate joystick to 【SCAN SPEED】, press
【OPEN】, tilt up/down joystick to adjust scan speed, press 【OPEN】 to
save.
4、 Left limit setting: operate joystick to 【SET LEFT LIMIT】, press
【OPEN】, operate joystick to choose objective image, press【OPEN】 to
save. Right limit setting is the same as left limit setting
.
5、Edit scan label: operate joystick, move the cursor to 【EDIT SCAN
LABEL】, press 【OPEN】 to enter submenu“ edit label”, move the cursor to 【LABEL】, the system will auto-set the label as AUTO SCAN, press
【OPEN】 to revise.
The label can set up to 16 characters, and doesn't need editing
characters. Pressing 【OPEN】 continuously to jump over and using
spacebar to replace the deleted characters. When you finish to edit a
character, pressing 【OPEN】 to enter into the next editing character
when you finish to edit the last character, pressing 【OPEN】to save.
Press 【CLOSE】 to exit.
Character of label is suitable for choosing as follow: 0-9、A-Z、:
<>-. , Space. The editing ways of other labels are the same as above.
6、Run scan: operate joystick to 【RUN SCAN】, press 【OPEN】 to exit
EDIT SCAN LABEL
LABEL：AUTO SCAN
BACK
EXIT
28
the menu, and it stars to run scan.
1. left limit and right limit of scan can't be set the same point.
2.Under scan process, speed, magnification and tilt direction won't
change, if the speed, magnification and tilt direction of the two
limits are inconsistent, run scan is base on left limit.
Function setting
MAIN MENU
SYSTEM SETTING
CAMERA SETTING
FUNCTION SETTING
WINDOW BLANKING
ALARMS
LANGUAGE
EXIT
6. 3 Pattern
Pattern is built-in function in camera; the PTZ can record tracks that are
no less than 180s. (A series of pan/tilt controlling and lens controlling
command). A PTZ may set up to 4 pattern tours.
1、The system enters into the main menu by calling 95 preset or by calling
9 preset twice within 3 seconds.
2、Operate joystick, move the cursor to 【FUNCTION SETTING】, press
【OPEN】 to enter submenu.
3、Operate joystick to 【PATTERN】, press 【OPEN】to enter menu “ Pattern”.
FUNCTION SETTING
PRESETS
SCAN
PATTERNS
TOUR
ZONES
TIME RUNNING
BACK
EXIT
● 【PATTERN NUMBER】
● 【PROGRAM PATTERN】
● 【RUN PATTERN】
● 【CLEAR PATTERN】
● 【EDIT PATTERN LABEL】
4、Choose pattern number: move the cursor to 【PATTERN NUMBER】,
press 【OPEN】, pattern you choose as current pattern, the following operations aim at the current pattern;
5、Define current pattern tour: move the cursor to 【PROGRAM
PATTERN】, press 【OPEN】to set pattern track, move the image random,
and draw the focus. The PTZ has a tour that is no less than 180s, a series of
PATTERNS
PATTERN NUMBER
PROGRAM PATTERN
RUN PATTERN
park time, magnification, focus will be recorded, press 【OPEN】 to save.
6、Run pattern: operate joystick to 【RUN PATTERN】, press 【OPEN】
to run, the PTZ will continuously and repeatedly record the specific track.
CLEAR PATTERN
EDIT PATTERN LABEL
BACK
EXIT
When carry out program, run, clear pattern and edit
label, should choose pattern number at first.
EDIT PATTERN LABEL
LABEL：PATTERN-1
BACK
EXIT
29
Function setting
MAIN MENU
SYSTEM SETTING
CAMERA SETTING
FUNCTION SETTING
WINDOW BLANKING
ALARMS
LANGUAGE
EXIT
6. 4 Tour
Tour is the built-in function in the PTZ, it will arrange the presets
into the queue of auto-tour, and can set how long it will park at preset.
Operate auto-tour is a process of incessantly transfer each preset. One
tour can store 32 presets at most.
1、 The system enters into the main menu by calling 95 preset or by calling
9 preset twice within 3 seconds.
2、 Operate joystick, move the cursor to 【FUNCTION SETTING】, press
【OPEN】enter submenu.
FUNCTION SETTING
PRESETS
SCAN
PATTERNS
TOUR
ZONES
TIME RUNNING
BACK
EXIT
3、Operate joystick, move the cursor to 【TOUR】, press【OPEN】 to
enter menu “tour”；
4、Set the park time of preset: Operate joystick, move the cursor to
【TOUR DWELL】, press 【OPEN】, there will be a sign
in the front of
【TOUR DWELL】, the cursor jumps to right, tilt up/down to set park time,
and the range is 000-255(s)
5、 Set tour :move the cursor to 【EDIT TOUR】,press【OPEN】 to set
tour interface,【PO-S-TM】 set preset ,speed and time ,press 【OPEN】,
the first dwell is activated , tilt up/down joystick to choose preset number,
the preset numerical value should be within 1-80 preset , a tour can set up
to 24 presets .press【OPEN】,the cursor jump to the next dwell ,tilt up/
TOUR
TOUR NUMBER
EDIT TOUR
RUN TOUR
CLEAR TOUR
BACK
EXIT
down joystick to choose current arrival preset speed , total 8 level of
1
speed ,increasingly from level 1 to level 8;Press 【OPEN】,the cursor
jumps to the next dwell , tilt up/down joystick to set current preset
maintaining time,60 seconds maximum . If set the presets of the second
line ,move the cursor to the second line , press 【OPEN】 to continue
edit .press 【OPEN】 to save after setting ,press 【CLOSE】 to exit.
6、 Run tour: Operate joystick, move the cursor to 【RUN TOUR 】, press
【OPEN】 to exit the menu, it stars to run tour.
EDIT TOUR
PO-S-TM PO-S-TM PO-S-TM
00-0-00 00-0-00 00-0-00
00-0-00 00-0-00 00-0-00
00-0-00 00-0-00 00-0-00
00-0-00 00-0-00 00-0-00
00-0-00 00-0-00 00-0-00
00-0-00 00-0-00 00-0-00
00-0-00 00-0-00 00-0-00
00-0-00 00-0-00 00-0-00
BACK
EXIT
30
the system will leap over the preset automatically when the
stay time of one item setting up on 0; The PTZ will not run
the tour of latter preset when preset or movement speed
setting up on 0 .
Function setting
6. 5 Zone
MAIN MENU
A PTZ may be set up to 8 zones; the regional scene can't be overlapped.
SYSTEM SETTING
CAMERA SETTING
FUNCTION SETTING
WINDOW BLANKING
ALARMS
LANGUAGE
EXIT
User can set label for each zone. When setting【ZONE LABEL】 as ON,
the PTZ will display zone label as it runs some zone. It is convenient to
know the zone that the camera shoots by setting zone label.
1、The system enters into the main menu by calling 95 preset or by calling
9 preset twice within 3 seconds.
2、Operate the joystick, move the cursor to 【FUNCTION SETTING】, press
【OPEN】to enter submenu.
FUNCTION SETTING
3、Operate the joystick, move the cursor to 【ZONES】, press 【OPEN】 to
enter submenu, as the left picture shows.
PRESETS
SCAN
PATTERNS
TOUR
ZONES
TIME RUNNING
BACK
EXIT
●
【ZONES NUMBER】
●
【SET LEFT LIMIT】
●
【SET RIGHT LIMIT】
●
【CLEAR ZONE】
●
【EDIT ZONE LABEL】
Regard the left/right limit as the demarcation line, and set the middle
part as a zone. Various operational ways are the same as other settings in the
menu. Therefore we won't explain it again.
ZONES
ZONES NUMBER
SET LEFT LIMIT
SET RIGHT LIMIT
CLEAR ZONE
EDIT ZONE LABEL
BACK
EXIT
1
EDIT ZONE LABEL
LABEL：ZONE-1
BACK
EXIT
31
Function setting
6 . 6 Time running
MAIN MENU
SYSTEM SETTING
CAMERA SETTING
FUNCTION SETTING
WINDOW BLANKING
ALARMS
LANGUAGE
EXIT
User can set the time of preset, scan, tour and pattern.
1.Call 95 preset or call 9 preset twice within 3 seconds to enter into the main
menu.
2. Operate the joystick, move the cursor to 【FUNCTION SETTING】 , press
【OPEN】 to call the submenu.
3. Operate the joystick, move the cursor to 【TIME RUNNING】 , press
【OPEN】 to enter into the menu setting. Please refer to the left picture.
【DAY】 set the date
FUNCTION SETTING
PRESETS
SCAN
PATTERNS
TOUR
ZONES
TIME RUNNING
BACK
EXIT
TIME RUNNING
DAY
SAT
TIME CHANNEL
1
START TIME
00:00
END TIME
00:00
RUNNING
TOUR1
BACK
EXIT
【TIME CHANNEL】 4 channels can be set.
【START TIME】 Set the start time
【END TIME】 Set the end time
【RUNNING】 User can set the preset , scan , tour,
pattern to every channel.(1-4)
4. This channel will not conflict with other channels when you set
【RUNNING】 as close.
1.When user do the action of scan, tour or pattern, if time is over,
then the PTZ will execute park action, the user's action will
stop. After the time, the PTZ will resume the action and preset
which is set before the park time. (Before the park time, if the
PTZ is on some preset, the PTZ will resume the preset, if PTZs
execute the action of scanning, tour or pattern, the PTZ will resume
original action. If users handle some action with keyboard, PTZ
will also resume the action which users are going on with keyboard.)
2. During the timing period of movement function, it is not allowed
that there is no action. When users handle the PTZ, the timing
movement function will interrupt. If there is no any action during
30 seconds, it will be in the state of timing function, and return
to the timing movement function. Or if there is idle function,
it will be do the action of idle time function.
3. Timing function will close while user setting presets, right and
left limit, menu status, recording scan and setting any other function.
4.When the PTZ execute alarm, timing, idle function, the priority for
alarm is the highest, for timing is the second, for idle is the lovest.
32
Privacy zone masking
MAIN MENU
SYSTEM SETTING
CAMERA SETTING
FUNCTION SETTING
WINDOW BLANKING
ALARMS
LANGUAGE
EXIT
7. Privacy zone masking
Privacy function can show someone piece of regional shielding while
protecting. For example, protect the window of bedroom or ATM of bank. A
PTZ can set up to 24 privacy windows.(Masking setting function is relative with the model of camera module. The masking numbers will be different according to the different cameras.)
Hitachi Camera: It can be set 8 masking at most in 360°surveillance
range,can set 2 masking at most per screen. The screen will note＂ please
move＂ when the position can not be set. It can not set masking when the
PTZ rotates down ≥45°.
Sony Camera: It can be set 24 masking at most in 360°surveillance range.
( Sony 45 series can be set 8 masking at most ). It can not set masking
when the PTZ rotates down ≥20°.LG,CNB Camera module have no
masking function.
WINDOW BLANKING
WINDOW NUMBER 01
EDIT WINDOW
ENABLE WINDOW OFF
CLEAR WINDOW
BACK
EXIT
Privacy zone masking
1、The system enters into the main menu by calling 95 preset or by calling
9 preset twice within 3 seconds.
2、Operate the joystick to 【WINDOW BLANKING】, press 【OPEN】to enter menu“ window blanking”.
● 【WINDOW NUMBER】 choose window number as current privacy window, other choices in the menu just aim at current privacy window;
● 【EDIT WINDOW】program current window ；
● 【ENABLE WINDOW】 permit/prohibit current privacy window,
there are two choices: ON---permit current privacy window/OFF---prohibit
current privacy window
● 【CLEAR WINDOW】clear current privacy window, after clearing
it, the window will auto- change as OFF.
3、Program current privacy window: Firstly choose window number, then
do the following operations:
a. Operate the joystick, move the cursor to 【EDIT WINDOW】, press【OPEN】 to move the image that need privacy window to display in the screen.
b . Press【OPEN】, there will be a square displaying in the center of the screen, operate the joystick, and move the square to the central place that need
to conceal.
c. Press【OPEN】, operate the joystick to adjust the size of privacy zone:
joystick to up, the height is increased; joystick to down, the height is reduced; joystick to right, the width is increased; joystick to left, the width is
reduced.
d. Press 【OPEN】 to save the current privacy zone setting, and the window
will auto-change as ON at the same time.
This function is decide by the parameter of built-in camera,
if the camera has not this function, this option is invalid. (N/A)
33
Alarm Function
MAIN MENU
SYSTEM SETTING
CAMERA SETTING
FUNCTION SETTING
WINDOW BLANKING
ALARMS
LANGUAGE
EXIT
ALARMS
RESUME
OFF
SEQUENCE
002
RESET DELAY
020
ALARM CONTACT N/C
ALARM SETTING
ARM SETTING
BACK
EXIT
ALARM SETTING
ALARM NUMBER
001
ALARM ACTION
TOUR
ACTIVATE AUX
NONE
ALARM PRIORITY
HIGH
BACK
EXIT
8. Alarm function
The PTZ may connect with 7 alarm input, 2 alarm output, and support alarm linkage. The external alarm message sends to the PTZ, then the PTZ sends to
alarm point shoot (to call preset, auto scan, auto cruise and auto pattern), and choose
that to run alarm output or not.
1、The system enters into the main menu by calling 95 preset or by calling 9 preset
twice within 3 seconds. click each menu according to the left picture, then enter menu alarm, choices as follow:
●【RESUME】resume mode after relieving alarm input, there are two choices: ON---clear alarm output, the PTZ will stop.
OFF---just clear alarm output.
●【SEQUENCE】 The park time between two alarm in the same priority, the
range is 1-60s.
●【RESET DELAY】set alarm reset and delay the time (1-225s)， how long
to relieve and run 【RESUME】 after the PTZ receives alarm message.
●【ALARM CONTACT 】set state of the relay. N/C---often close the state,
N/O---often hold the state. If setting as often closing the state, the relay is
in closing the state when there is no alarm to output; when there is alarm to
output, the relay is in holding the state.
●【ALARM SETTING】
●【ARM SETTING】
2、Operate joystick, move the cursor to【ALARM SETTING】, press【OPEN】
to enter the menu alarm setting
●【ALARM NUMBER】alarm number is corresponding with 12 bits plug in
the external switching board of the PTZ (as below shows). 001 priority is
the highest, 007 priority is the lowest. The two lines alarm input at the same time, the PTZ run alarm that the highest priority.
●【ALARM ACTION】as current alarm input, to run the action. Choices for
choosing as follow. NONE---none action/SCAN/PAT X---run a pattern tour
/TOUR---run tour/PRESET---call preset, when the PTZ number is set as 1,
to call preset 1; when the PTZ number is set as 2, to call preset2.
●【ACTIVATE AUX】as current alarm input, to run alarm output or not. NONE---none alarm output/AUX 1---the first alarm output/AUX 2---the secretaryond alarm output/BOTH--- two alarms output.
●【ALARM PRIORITY】 alarm priority can be defined as three grades:
high, middle, low.
AUX2 AUX1 GND 7 6 5 4 3 2 1
ALARMS
Alarm input 1-7bits
earthing
Alarm ouput 1
Alarm output 2
34
Alarm Function
MAIN MENU
SYSTEM SETTING
CAMERA SETTING
FUNCTION SETTING
WINDOW BLANKING
ALARMS
LANGUAGE
EXIT
3.ARM Setting
1. Call 95 preset or call 9 preset twice within 3 seconds and then input the
password to enter the main menu.
2. Operate the joystick up and down, move the cursor to 【ALARMS 】 , press
【OPEN】 to call the submenu.
3. Operate the joystick up and down, move the cursor to 【ARM SETTING】 ,
press 【OPEN 】to call the submenu. Please refer to the left picture.
4. Operate the joystick up and down, move the cursor to 【DAY】, Press
【OPEN 】to choose it , Operate the joystick up and down to set date, set the
ALARMS
date according to the week. To set the Alarm state and Alarm date based on
RESUME
OFF
SEQUENCE
002
RESET DELAY
020
ALARM CONTACT N/C
ALARM SETTING
ARM SETTING
BACK
EXIT
the time.
● 【ARM STATE】 Alarm off /Alarm on
(Alarm Setting is noneffective under Alarm off. Alarm Setting
is effective under Alarm on)
● 【ARM TIME】 : User can set the alarm time.
● 【UNARM TIME】: User can set the alarm off time.
● 【BACK 】: back to the former menu.
● 【EXIT】: Exit the menu.
ARM SETTING
DAY
ARM STATE
ARM TIME
UNARM TIME
BACK
EXIT
SUN
OFF
N/A
N/A
35
Set Language
MAIN MENU
SYSTEM SETTING
CAMERA SETTING
FUNCTION SETTING
WINDOW BLANKING
ALARMS
LANGUAGE
EXIT
LANGUAGE
LANGUAGE
BACK
EXIT
36
ENGLISH
9.Set Language
1. Call 95 preset or call 9 preset twice within 3 seconds and then input the
password to enter the main menu.
2. Operate the joystick up and down, move the cursor to 【LANGUAGE】 ,
press 【OPEN】 to call the submenu.
3、Operate the joystick to choose the language，English and French can be
choosed, Then press 【OPEN】to save。
Appendix
10 Appendix
10. 1 Menu Index
SYSTEM SETTING
CAMERA SETTING
EDIT DOME LABEL
INITIAL INFO
DISPLAY SETUP
MOTION
CLEAR
PASSWORD SETUP
CLOCK SETTING
DOME ADDRESS
BACK
EXIT
ZOOM SPEED
HIGH
DIGITAL ZOOM
OFF
BLC MODE
OFF
SLOW SHUTTER
OFF
LINE SYNC
N/A
WDR MODE
N/A
ADVANCE SETTING 1
ADVANCE SETTING2
BACK
EDIT DOME LABEL
IR CUT FILTER
AUTO
IR CUT ON TIME N/A
IR CUT OFF TIME N/A
THRESHOLD
10dB
FLIP
OFF
MIRROR
OFF
MAX GAIN
08dB
EXPOSURECOMP OFF
BACK
EXIT
INITIAL INFO
S/N:8D SAD7B26200 000
FIRMWARE
V1.60
PROTO COL：PELCO
DOME A DDRESS：001
COMM ：4800,N,8,1
BACK
EXIT
ADVANCE SETTING 2
DISPLAY SETUP
OFF
OFF
ON
OFF
ON
OFF
ON
ON
AE MODE
SHUTTER
IRIS
BRIGHT
W B MODE
R GAIN
B GAIN
HI-RESOLU
BACK
EXIT
AUTO
N/A
N/A
N/A
AUTO
N/A
N/A
018
MOTION
AUTO FLIP
PROPORTION
PARK TIME
PARK ACTION
POWER UP ACTION
FAN ENABLED
TEMP C/F
ADVANCE SETTING
BACK
ON
ON
005
SCAN
AUTO
045C
CENT
CLEAR
CLEAR ALL ZONES
CLEAR ALL PRESETS
CLEAR ALL PATTERNS
CLEAR ALL TOURS
CLEAR ALL WINDOWS
FACTORY DEFAULTS
RESTART
BACK
EXIT
PASSWORD SETUP
OLD :******
NEW :******
CONF :******
ENABLE :
BACK
EXIT
OFF
CLOCK SETTING
TIME
DATE
DAY
EXIT
FUNCTION SETTING
WINDOW BLANKING
PRESETS
SCAN
PATTERNS
TOUR
ZONES
TIME RUNNING
AUTO TRACKING
BACK
EXIT
WINDOW NUMBER
EDIT WINDOW
ENABLE WINDOW
CLEAR WINDOW
BACK
EXIT
PRESETS
ADVANCE SETTING1
L：SPEED DOME
BACK
EXIT
DOME LABEL
PRESET LABEL
ZOOM LABEL
ZONE LABEL
DIR. LABEL
TEM. LABEL
TIME LABEL
DATE LABEL
BACK
MAIN MENU
SYSTEM SETTING
CAMERA SETTING
FUNCTION SETTING
WINDOW BLANKING
ALARMS
LANGUAGE
EXIT
03:20:18
07:10:10
WED
DOME ADDRESS
S / N: 6D3AD7B26200001
CONF:6D3AD7B26100001
DOME ADDRESS:0005
BACK
EXIT
01
OFF
EDIT PRESET LABEL
PRESET NUMBER 05
SET PRESET
SHOW PRESET
CLEAR PRESET
AUTO TARCKING NONE
EDIT PRESET LABEL
BACK
EXIT
SCAN
L：AUTO SCAN
BACK
EXIT
OFF
002
020
N/C
ALARM SETTING
ALARM NUMBER
ALARM ACTION
ACTIVATE AUX
ALARM PRIORITY
BACK
EXIT
L：PRESET 05
BACK
EXIT
EDIT SCAN LABEL
SCAN NUMBER 04
SCAN SPEED
50
SET LEFT LIMIT
SET RIGHT LIMIT
RUN SCAN
CLEAR SCAN
EDIT SCAN LABEL
BACK
EXIT
ALARMS
RESUME
SEQUENCE
RESET DELAY
ALARM CONTACT
ALARM SETTING
ARM SETTING
BACK
EXIT
001
TOUR
NONE
HIGH
ARM SETTING
DAY
ARM STATE
ARM TIME
UNARM TIME
BACK
EXIT
SUN
OFF
N/A
N/A
EDIT PATTERN LABEL
PATTERNS
PATTERN NUMBER
PROGRAM PATTERN
RUN PATTERN
CLEAR PATTERN
EDIT PATTERN LABEL
BACK
EXIT
L：PATTERN 1
BACK
EXIT
EDIT TOUR
LANGUAGE
LANGUAGE
BACK
EXIT
ENGLISH
PO-S-TM PO-S-TM
ADVANCE SETTING
EIS ENABLED
N/A
PRESET FREEZE
N/A
DEFOGGER
10
A D J SPEED
100
WIPER
IR HEADLIGHT
BACK
EXIT
00-0-00
00-0-00
00-0-00
00-0-00
00-0-00
00-0-00
00-0-00
00-0-00
TOUR
TOUR NUMBER
EDIT TOUR
RUN TOUR
CLEAR TOUR
BACK
EXIT
1
BACK
EXIT
EDIT ZONE LABEL
ZONES
IR HE ADL IGHT
MODE
DEL AY TIME
BW
ACT. AU X1
LED 1
LED 2
LED 3
LIGHT
BACK
EXIT
MID
002
AUTO
OFF
100
200
×
×
00-0-00
00-0-00
00-0-00
00-0-00
00-0-00
00-0-00
00-0-00
00-0-00
ZONES NUMBER
SET LEFT LIMIT
SET RIGHT LIMIT
CLEAR ZONE
EDIT ZONE LABEL
BACK
EXIT
1
L：ZONE 1
BACK
EXIT
TIME RUNNING
DAY
TIME CHANNEL
START TIME
END TIME
RUNNING
BACK
EXIT
SAT
1
00:00
00:00
TOUR1
AUTO TRACKING
DAY
THU
STATE
OFF/TIME
START TIME
00:00
END TIME
00:00
SENSITIVE
MID
TRACKING-ZOOM
OFF
TRACKING-SPEED
MID
TRACKING PARA
BACK
EXIT
TRACKING PARA
SET LEFT LIMET
SET RIGHT LIM ET
SET UP LIMET
SET DOWN LIM ET
PARK TIME 000s
PARK ACTION NONE
BACK
EXIT
37
Appendix
10.2 24VAC Wire Diameter and Transmission Distance
Comparison chart
The transmission distances listed below are farthest ones recommended for each giving
wire diameter when the 24VAC voltage loss ratio is below 10%(for equipment powered by
AC, the allowed maximum voltage loss ratio is 10%).
The rating power of PTZ is 50W, need a wire with a minimum diameter of 1.0mm.
Wi re Diameter
(mm)
0 .8 00
1. 0 00
1 .2 50
2.0 00
Power(va)
38
10
283（8 6）
451（1 37）
716（2 18）
181 1（5 51）
20
141（4 2）
22 5（6 8）
358（1 09）
905（275）
30
94（28）
15 0（4 5）
2 38（7 2）
603（183）
40
70（21）
11 2（3 4）
1 97（5 4）
452（13 7）
50
56（17）
90（27）
14 3（43）
362（110）
60
47（14）
75（22）
1 19（3 6）
30 1（91）
70
40（12）
64（19）
1 02（3 1）
25 8（78）
80
35（10）
56（17）
89（27）
22 6（68）
90
31（9）
50（15）
79（24）
20 1（61）
100
28（8）
45（13）
71（21）
18 1（55）
110
25（7）
41（12）
65（19）
16 4（49）
120
23（7）
37（11）
59（17）
15 0（45）
130
21（6）
34（10）
55（16）
13 9（42）
140
20（6）
32（9）
51（15）
12 9（39）
150
18（5）
30（9）
47（14）
12 0（36）
160
17（5）
28（8）
44（13）
11 3（34）
170
16（4）
26（7）
42（12）
10 6（32）
180
15（4）
25（7）
39（11）
10 0（30）
190
14（4）
23（7）
37（11）
95（28）
200
14（4）
22（6）
35（10）
90（27）
Appendix
10.3 Domestic and Abroad Wire Gauge Conversion Chart
Bare Wire Diameter
Metric Size(mm)
AWC
(Apprximate)
SWC
(Approximate)
Bare Wire Cross-Sectional
Area（mm 2）
0.0 50
43
47
0. 0 0196
0.0 60
42
46
0.0 0283
0.0 70
41
45
0.0 0385
0.0 80
40
44
0.0 0503
0.0 90
39
43
0.0 06 36
0.0 10
38
42
0.0 0785
0.1 10
37
41
0.0 09 50
0.1 30
36
39
0.0 13 27
0.1 40
35
0.1 60
34
0.1 80
33
0.2 00
32
0.2 30
31
0.2 50
30
33
0.0 49 09
0.2 90
29
31
0.0 6605
0.3 30
28
30
0.0 8553
0.3 50
27
29
0. 096 21
0.4 00
26
28
0. 1257
0.4 50
25
0.5 60
24
24
0.2 463
0.6 00
23
23
0. 2827
0.7 10
22
22
0. 3 958
0.7 50
21
0.8 00
20
21
0. 5027
0.9 00
19
20
0.6 362
1.0 00
18
19
0. 78 54
1.2 50
16
18
1. 22 66
1.5 00
15
2.0 00
12
0.0 15 39
37
0. 020 11
0.0 2545
35
0.0 31 42
0.0 4115
0.1 602
0. 4417
1.7 663
12
3. 14 20
2.5 00
4. 90 80
3.0 00
7.0 683
39
Appendix
10. 4 Rs485 Bus Basic Knowledge
Ø Characteristics of Rs485 Bus
Ø The connection of 120Ω termination resistor:
As specified by Rs485 standard, Rs485 Bus is of
half-duplexed data transmission cables with characteristic impedance as 120Ω. The maximum load
capacity is 32 unit loads (including main controller
and controlled equipment.)
Connection mode for 120 Ω resistance of equipment
terminal. Setting connection of terminal resistance
120Ω in the base cover. (Refer to Picture 10-4.3):
Default of factory (No.8 digit of SW2 is set “OFF”
on code switch)No.8 digit of SW2 is set “ON” on
code switch if needed to connect 120 resistance.
Ø Transmission distances of Rs485 Bus
When user selects the 0.56mm(24AWG)twisted pair wires as data transmission cable, the maximum theoretical transmitting distance are as foll-
Setting of 120Ωresistance
ows:
Baud rate
Max distance
2400BPS
1800m
4800BPS
1200m
9600BPS
800m
19200BPS
600m
Sw2
If user selects thinner cables, or installs the PTZ
in an environment with strong electromagnetic
interference, or connects lots of equipment to the
Rs485 Bus, the maximum transmitting distance will be decreased. To increase the maximum transmitting distance, do the contrary.
Ø Connection and termination resistor
The Rs485 standards require a daisy-chain Connection between the equipment. There must be termination resistors with 120Ω (as the picture 10-2.1).
Please refer to picture 10-2.2 for simple connection.
“D”should not exceed 7m.
120Ω
1#
120Ω
2#
3#
4#
32#
Picture 10-4.1
A+
B-
D
A+
B-
2#
3#
120Ω
1#
120Ω
4#
32#
Picture 10-4.2
40
Sw1
Picture10-4.3
Appendix
Ø Problems in practical connections
In some circumstances user adopts a star co-
In such circumstances the factory recommends
the usage of RS485 distributor. The distributor can
nfiguration in practical connection. The termina-
change the star configuration connection to the mode
tion resistors must be connected to the two equi-
of connection stipulated in the RS485 standards.
pment 1# and 5# in Picture 10-4.4. As the star con-
The new connection achieves reliable data transmi-
figuration is not in conformity with the require-
ssion. (Refer to Picture 10-4.5).
ments of RS485 standards, problems such as signal reflections, lower anti-interference performance arise when the cables are long in the connection. The reliability of control signals is decreased with the phenomena that the PTZ does not
respond to or just responds at intervals to the co-
Rs485 Distributor
A+
B-
120Ω
1#
120Ω
2#
120Ω
3#
ntroller, or does continuous operation without
stop.
120Ω
1#
Picture10-4.5
6#
Main controller
32#
120Ω
15#
Picture 10-4.4
Ø Rs485 Bus troubleshooting
Trouble
PTZ can do
self-testing
but cannot be
controlled
The PTZ can be
controlled but
the operation is
not smooth.
Possible cause
Solution
A、The address and baud rate setting of PTZ
are not in conformity with those of controller.
B、The "+" and "-"connection of Rs485 Bus is
incorrect.
C、The PTZ is very far away from controller.
D、There are too many PTZs connected in the
System.
A、Change the address and baud rate of controller or PTZ
B、Replace Rs485 Bus wires
C、Make sure the connections are fully seated
A、The Rs485 Bus line is not in good
contact with the connectors.
B、One wire of the Rs485 Bus is
broken.
C、The PTZ is very far from
controller.
D、There are too many PTZ
connected in the system.
A、Secure the connection；
B、Replace Rs485 Bus Wires
C、Add termination resistors to the system
D、Install Rs485 distributor
41
Appendix
10. 5 DIP switch setup
Open base, there are two code switches with
10. 5. 2 Protocol setup（SW2）
8 digits, SW1and SW2. SW1 is for setting of
PROTOCOL
PTZ ID; SW2 is for settings of control protocol,
FACTORY
baud rate, terminal resistance connect.
SW2
SW1
Picture 10-5.1
SWITCH NUMBER （SW2）
(Bit) 1
2
3
4
5
0
0
0
0
0
PELCO
1
0
0
0
0
ERNITEC
0
1
0
0
0
VCL
1
1
0
0
0
MOLYNX
0
0
1
0
0
VICON
1
0
1
0
0
SANTACHI
0
1
1
0
0
PANASONIC
1
1
1
0
0
SAMSUNG
0
0
0
1
0
DIAMOND
1
0
0
1
0
KALATEL
0
1
0
1
0
LILIN
1
1
0
1
0
VIDO B02
0
0
1
1
0
HUNDA
1
0
1
1
0
PHILIPS
0
0
0
1
1
AD
1
0
0
1
1
(FACTORY PROTOCOL)
RESERVED
OTHERS
In the following list, “1”set DIP as
“ON” 0 set DIP as “OFF ”
10. 5. 3 ID setting（SW1）
The ID switch in decoder and the ID setting of
10. 5. 1 Baud rate setup（SW2）：
Please according to "AppdienxRS485 Bus
Basic knowledge", to check whether Baud
rate is satisfied with the demand of
transmission distance.
Baud rate
2400bps
4800bps
9600bps
19200bps
42
Switch number (Sw2)
(Bit) 6 7
0 0
1 0
0 1
1 1
the PTZ as follow, in the picture,"1" set DIP
switch as "NO", "0" set DIP switch as OFF.
Appendix
ID
S w i t c h n u m b e r (Sw1)
(Bit) 1 2 3 4 5 6 7 8
ID
S w i t c h n u m b e r (Sw1)
(Bit) 1 2 3 4 5 6 7 8
Factory defaults
set as debug address
0 0 0 0 0 0 0 0
34
0 1 0 0 0 1 0 0
1
1 0 0 0 0 0 0 0
35
1 1 0 0 0 1 0 0
2
0 1 0 0 0 0 0 0
36
0 0 1 0 0 1 0 0
3
1 1 0 0 0 0 0 0
37
1 0 1 0 0 1 0 0
4
0 0 1 0 0 0 0 0
38
0 1 1 0 0 1 0 0
5
1 0 1 0 0 0 0 0
39
1 1 1 0 0 1 0 0
6
0 1 1 0 0 0 0 0
40
0 0 0 1 0 1 0 0
7
1 1 1 0 0 0 0 0
41
1 0 0 1 0 1 0 0
8
0 0 0 1 0 0 0 0
42
0 1 0 1 0 1 0 0
9
1 0 0 1 0 0 0 0
43
1 1 0 1 0 1 0 0
10
0 1 0 1 0 0 0 0
44
0 0 1 1 0 1 0 0
11
1 1 0 1 0 0 0 0
45
1 0 1 1 0 1 0 0
12
0 0 1 1 0 0 0 0
46
0 1 1 1 0 1 0 0
13
1 0 1 1 0 0 0 0
47
1 1 1 1 0 1 0 0
14
0 1 1 1 0 0 0 0
48
0 0 0 0 1 1 0 0
15
1 1 1 1 0 0 0 0
49
1 0 0 0 1 1 0 0
16
0 0 0 0 1 0 0 0
50
0 1 0 0 1 1 0 0
17
1 0 0 0 1 0 0 0
51
1 1 0 0 1 1 0 0
18
0 1 0 0 1 0 0 0
52
0 0 1 0 1 1 0 0
19
1 1 0 0 1 0 0 0
53
1 0 1 0 1 1 0 0
20
0 0 1 0 1 0 0 0
54
0 1 1 0 1 1 0 0
21
1 0 1 0 1 0 0 0
55
1 1 1 0 1 1 0 0
22
0 1 1 0 1 0 0 0
56
0 0 0 1 1 1 0 0
23
1 1 1 0 1 0 0 0
57
1 0 0 1 1 1 0 0
24
0 0 0 1 1 0 0 0
58
0 1 0 1 1 1 0 0
25
1 0 0 1 1 0 0 0
59
1 1 0 1 1 1 0 0
26
0 1 0 1 1 0 0 0
60
0 0 1 1 1 1 0 0
27
1 1 0 1 1 0 0 0
61
1 0 1 1 1 1 0 0
28
0 0 1 1 1 0 0 0
62
0 1 1 1 1 1 0 0
29
1 0 1 1 1 0 0 0
63
1 1 1 1 1 1 0 0
30
0 1 1 1 1 0 0 0
64
0 0 0 0 0 0 1 0
31
1 1 1 1 1 0 0 0
65
1 0 0 0 0 0 1 0
32
0 0 0 0 0 1 0 0
66
0 1 0 0 0 0 1 0
33
1 0 0 0 0 1 0 0
67
1 1 0 0 0 0 1 0
43
Appendix
ID
44
Switch number
(Sw1)
Switch number
(Sw1)
(Bit) 1 2 3 4 5 6 7 8
ID
68
0 0 1 0 0 0 1 0
102
0 1 1 0 0 1 1 0
69
1 0 1 0 0 0 1 0
103
1 1 1 0 0 1 1 0
70
0 1 1 0 0 0 1 0
104
0 0 0 1 0 1 1 0
71
1 1 1 0 0 0 1 0
105
1 0 0 1 0 1 1 0
72
0 0 0 1 0 0 1 0
106
0 1 0 1 0 1 1 0
73
1 0 0 1 0 0 1 0
107
1 1 0 1 0 1 1 0
74
0 1 0 1 0 0 1 0
108
0 0 1 1 0 1 1 0
75
1 1 0 1 0 0 1 0
109
1 0 1 1 0 1 1 0
76
0 0 1 1 0 0 1 0
110
0 1 1 1 0 1 1 0
77
1 0 1 1 0 0 1 0
111
1 1 1 1 0 1 1 0
78
0 1 1 1 0 0 1 0
112
0 0 0 0 1 1 1 0
79
1 1 1 1 0 0 1 0
113
1 0 0 0 1 1 1 0
80
0 0 0 0 1 0 1 0
114
0 1 0 0 1 1 1 0
81
1 0 0 0 1 0 1 0
115
1 1 0 0 1 1 1 0
82
0 1 0 0 1 0 1 0
116
0 0 1 0 1 1 1 0
83
1 1 0 0 1 0 1 0
117
1 0 1 0 1 1 1 0
84
0 0 1 0 1 0 1 0
118
0 1 1 0 1 1 1 0
85
1 0 1 0 1 0 1 0
119
1 1 1 0 1 1 1 0
86
0 1 1 0 1 0 1 0
120
0 0 0 1 1 1 1 0
87
1 1 1 0 1 0 1 0
121
1 0 0 1 1 1 1 0
88
0 0 0 1 1 0 1 0
122
0 1 0 1 1 1 1 0
89
1 0 0 1 1 0 1 0
123
1 1 0 1 1 1 1 0
90
0 1 0 1 1 0 1 0
124
0 0 1 1 1 1 1 0
91
1 1 0 1 1 0 1 0
125
1 0 1 1 1 1 1 0
92
0 0 1 1 1 0 1 0
126
0 1 1 1 1 1 1 0
93
1 0 1 1 1 0 1 0
127
1 1 1 1 1 1 1 0
94
0 1 1 1 1 0 1 0
128
0 0 0 0 0 0 0 1
95
1 1 1 1 1 0 1 0
129
1 0 0 0 0 0 0 1
96
0 0 0 0 0 1 1 0
130
0 1 0 0 0 0 0 1
97
1 0 0 0 0 1 1 0
131
1 1 0 0 0 0 0 1
98
0 1 0 0 0 1 1 0
132
0 0 1 0 0 0 0 1
99
1 1 0 0 0 1 1 0
133
1 0 1 0 0 0 0 1
100
0 0 1 0 0 1 1 0
134
0 1 1 0 0 0 0 1
101
1 0 1 0 0 1 1 0
135
1 1 1 0 0 0 0 1
(Bit) 1 2 3 4 5 6 7 8
Appendix
ID
Switch number
(Sw1)
(Bit) 1 2 3 4 5 6 7 8
ID
Switch number
(Sw1)
(Bit) 1 2 3 4 5 6 7 8
136
0 0 0 1 0 0 0 1
170
0 1 0 1 0 1 0 1
137
1 0 0 1 0 0 0 1
171
1 1 0 1 0 1 0 1
138
0 1 0 1 0 0 0 1
172
0 0 1 1 0 1 0 1
139
1 1 0 1 0 0 0 1
173
1 0 1 1 0 1 0 1
140
0 0 1 1 0 0 0 1
174
0 1 1 1 0 1 0 1
141
1 0 1 1 0 0 0 1
175
1 1 1 1 0 1 0 1
142
0 1 1 1 0 0 0 1
176
0 0 0 0 1 1 0 1
143
1 1 1 1 0 0 0 1
177
1 0 0 0 1 1 0 1
144
0 0 0 0 1 0 0 1
178
0 1 0 0 1 1 0 1
145
1 0 0 0 1 0 0 1
179
1 1 0 0 1 1 0 1
146
0 1 0 0 1 0 0 1
180
0 0 1 0 1 1 0 1
147
1 1 0 0 1 0 0 1
181
1 0 1 0 1 1 0 1
148
0 0 1 0 1 0 0 1
182
0 1 1 0 1 1 0 1
149
1 0 1 0 1 0 0 1
183
1 1 1 0 1 1 0 1
150
0 1 1 0 1 0 0 1
184
0 0 0 1 1 1 0 1
151
1 1 1 0 1 0 0 1
185
1 0 0 1 1 1 0 1
152
0 0 0 1 1 0 0 1
186
0 1 0 1 1 1 0 1
153
1 0 0 1 1 0 0 1
187
1 1 0 1 1 1 0 1
154
0 1 0 1 1 0 0 1
188
0 0 1 1 1 1 0 1
155
1 1 0 1 1 0 0 1
189
1 0 1 1 1 1 0 1
156
0 0 1 1 1 0 0 1
190
0 1 1 1 1 1 0 1
157
1 0 1 1 1 0 0 1
191
1 1 1 1 1 1 0 1
158
0 1 1 1 1 0 0 1
192
0 0 0 0 0 0 1 1
159
1 1 1 1 1 0 0 1
193
1 0 0 0 0 0 1 1
160
0 0 0 0 0 1 0 1
194
0 1 0 0 0 0 1 1
161
1 0 0 0 0 1 0 1
195
1 1 0 0 0 0 1 1
162
0 1 0 0 0 1 0 1
196
0 0 1 0 0 0 1 1
163
1 1 0 0 0 1 0 1
197
1 0 1 0 0 0 1 1
164
0 0 1 0 0 1 0 1
198
0 1 1 0 0 0 1 1
165
1 0 1 0 0 1 0 1
199
1 1 1 0 0 0 1 1
166
0 1 1 0 0 1 0 1
200
0 0 0 1 0 0 1 1
167
1 1 1 0 0 1 0 1
201
1 0 0 1 0 0 1 1
168
0 0 0 1 0 1 0 1
202
0 1 0 1 0 0 1 1
169
1 0 0 1 0 1 0 1
203
1 1 0 1 0 0 1 1
45
Appendix
ID
46
Switch number
(Sw1)
(Bit)1 2 3 4 5 6 7 8
ID
Switch number
(Sw1)
(Bit) 1 2 3 4 5 6 7 8
204
0 0 1 1 0 0 1 1
238
0 1 1 1 0 1 1 1
205
1 0 1 1 0 0 1 1
239
1 1 1 1 0 1 1 1
206
0 1 1 1 0 0 1 1
240
0 0 0 0 1 1 1 1
207
1 1 1 1 0 0 1 1
241
1 0 0 0 1 1 1 1
208
0 0 0 0 1 0 1 1
242
0 1 0 0 1 1 1 1
209
1 0 0 0 1 0 1 1
243
1 1 0 0 1 1 1 1
210
0 1 0 0 1 0 1 1
244
0 0 1 0 1 1 1 1
211
1 1 0 0 1 0 1 1
245
1 0 1 0 1 1 1 1
212
0 0 1 0 1 0 1 1
246
0 1 1 0 1 1 1 1
213
1 0 1 0 1 0 1 1
247
1 1 1 0 1 1 1 1
214
0 1 1 0 1 0 1 1
248
0 0 0 1 1 1 1 1
215
1 1 1 0 1 0 1 1
249
1 0 0 1 1 1 1 1
216
0 0 0 1 1 0 1 1
250
0 1 0 1 1 1 1 1
217
1 0 0 1 1 0 1 1
251
1 1 0 1 1 1 1 1
218
0 1 0 1 1 0 1 1
252
0 0 1 1 1 1 1 1
219
1 1 0 1 1 0 1 1
253
1 0 1 1 1 1 1 1
220
0 0 1 1 1 0 1 1
254
0 1 1 1 1 1 1 1
221
1 0 1 1 1 0 1 1
255
1 1 1 1 1 1 1 1
222
0 1 1 1 1 0 1 1
223
1 1 1 1 1 0 1 1
224
0 0 0 0 0 1 1 1
225
1 0 0 0 0 1 1 1
226
0 1 0 0 0 1 1 1
227
1 1 0 0 0 1 1 1
228
0 0 1 0 0 1 1 1
229
1 0 1 0 0 1 1 1
230
0 1 1 0 0 1 1 1
231
1 1 1 0 0 1 1 1
232
0 0 0 1 0 1 1 1
233
1 0 0 1 0 1 1 1
234
0 1 0 1 0 1 1 1
235
1 1 0 1 0 1 1 1
236
0 0 1 1 0 1 1 1
237
1 0 1 1 0 1 1 1
Notice:
Debug address: (Only factory
protocol and Pelco can be set): if the camera
address is set as 0, user can select any
protocols to control the PTZ.
Warnings
11.Installation
11.1 Caution
l Please refer to user manual before installation.
l Power: AC 220V/110V-AC24V, for actual needs, please refer to label of product.
l Precise optical and electronic parts inside of product. Avoiding severe press, hard vibration etc non-correct
operation methods, which may cause damage to product when transportation and installation.
l Please do not disassemble parts inside of product at random, which may cause negative influence on use
of product. No additional parts available.
l Please comply with standards of Electrify Safety and use our own power transformer of product. Enough
distance must be ensured between RS-485 cable, Video signal cable and equipments of high voltage when
transmission. Thunder-proof, surge-proof and wave-proof , etc protection measures are needed.
l Do not use product beyond the rated temperature, humidity or specifications of power. Do not place camera
point to Sun or shining objects.
l Do not use cleansers with abrasion to clean product. Please use dry cloth to clean up dirt; Neutral cleanser
is needed when not easy to clean.
l Handle product with care so as to avoid crash or vibration; Damage is caused when incorrect usage.
l Please fix product to the position which is solid and firm.
l Please use special paper of lens to clean up dirt on Lens.
11. 2 Distributing the Line in Security
Please refer to right picture 11.1-1
= It is necessary to keep 50 meters distances at least bet-
Power cable lightning rob
Communication cable lightning rob
Video cable lightning rob
ween the high voltage unit and the high voltage cable with
signal transmission line.
45
O
The PTZ must be installed
within the angle of 45 degrees
under lightning rob
= Outdoor wiring is best to along under the eave of the
house.
= Wiring at void place must adopt by way of sealed steel
tube bury underground, and sealed steel tube should be grounded by one Bus. It is absolutely forbidden to adopt wiring without holder.
Ground resistance should
be lower than 4Ω
Sealed steel tube
= Under thunderstorm or high inductive voltage region
(e.g.: high voltage transformer substation),
you must add extra high power lightning proof equipment
and install lighting rob.
Picture 11-1.1
= Outdoor equipment, routes of lighting proof and ground design must consider according to the request of construction
lightning proof, and coincide with connection requests of country and industry standard.
●The system must equipotential ground. Grounding equipment must satisfy the anti-jamming and electrical safety requirements and must not short circuited or mix connection with high voltage electricity net. When the system is grounded
separately, the ground resistance should be not more than 4Ωand section of the grounding conducting wire should be less than
25 mm .
2
47
Warnings
11. 3 Lightning Proof and Surge Proof
This product uses TVS lightning Proof technology,
can prevent from the damage of the equipment caused by
kinds of pulse signal such as instant lightning strike of
power below 4000V, the surge and so on.
At the same time, you must adopt the essential protective measure according to the actual situation regarding
outdoor installation under the guarantee electricity security.
(Refer to chapter 1.3 Distributing the line in security)
11. 4 Water Proof
Outdoor PTZ has well waterproof 、moisture-proof 、
dustproof performance, has achieved the IP66 international
standard. The indoor PTZ doesn't allowed to install in outdoor environment which is full of moisture and possibly enter water. You should prevent the product and the internal
components from damage that caused by the long time water
-drop or spatter.
11.5 The preparation of installation
Ø The request of the quality of installation
person and maintainer:
● All installation and maintenance work related this
product should complete by technical personnel who
have qualification of installation and maintenance.
Ø Basic requirements
●Please refer to this handbook for detail.
●All electrical work must be observe local latest
electricity laws, regulation on fireproof as well as
the related laws and regulations:
●Checking everything is completed according to
packing list. Make sure the application place and
the way of installation for PTZ is coincide with
the request. If not, please contact your supplier.
●Please use this product according to the working
conditions request.
●Please handle with the pan/tilt module carefully,
do not extrude various structure parts; The down
cover belongs to the senior optics part, do not touch
with hand; Please do not get through power except
for the electrifying inspection in process of installation.
Ø Check the structure intensity for installation
space and installation site.
●Make sure you have enough space to hold this product
and it's parts of installation in the site.
●Make sure the bearing capacity of ceiling, wall,
bracket that installs the PTZ support the gross weight
of the PTZ and the structural parts of installation.
It is necessary to have the safe coefficient of 4 times
or above.
48
Ø Stuff Preparation
Please select the type of cables based on transmitting distance:
●Minimum video coaxial cable requirements:
1)75Ωimpedance
2)All copper conductor wire
3)95% copper net structure
Domestic Gauge
International Gauge
Maximum Distance(ft/m)
RG59/U
750ft（229m）
5C-2V
RG6/U
1,000ft（305m）
7C-2V
RG11/U
1,500ft（457m）
RG59/U
●RS485 Communication cables (Refer to manual appendix)
●24VAC Power supply cable (Refer to manual appendix)
Ø Keep All the Original Package Materials
Please preserve the mode original package material
properly after opening the PTZ packing, in order to
mail the PTZ that is wrapped with original package
material to the agent or return it to the factory to repair
if problem occur.
It is likely to bring on the damage that caused by the
transport accident on the way if the mode uses the
non-original package material, and extra cost may
arise accordingly.
Ø Brief introduction of mounting way
Mounting way of pan/tilt: wall mount, top-down
mount, stand-up mount.
● Stand-up mount
The mounting place must meet the requirement of
chapter 1.3 distributing the line in security.
The pole bracket must be stability and no wobble.
●Top-down mount
The mounting position must undertake the weight of
pan-tilt.
Such a mounting way is only suitable for top-down type.
Otherwise, it would be water-leaking.
● Wall mount
The mounting place must bear four times weight of
PTZ/ mounting bracket and mounting base.
The wall place you choose for mounting site must be
stability and nothing to take off, and make sure the
bracket is mounted in the wall not the non-surface
object.
Installation Introduction
11.6 Structure Introduction
The pan/tilt camera has five parts: main body, camera protection shield, LED protection shield,
pedestal and pedestal pad. DIP switch setup inside pedestal; and original integrated packing.
Main body
Camera protection
LED protection shield
Pedestal up cover
Pedestal down cover
Pedestal pad
Picture11.6-1
11.7 Basic Size graph
411
210
161
Picture11.7-1
49
Installation Introduction
11.8 Installation
Stand-up mount，top-dowm mount and wall mount
are available for this product, which are suitable for
different installation environment. Because this product
is integrated package, please set parameters of baud rate,
control protocol as well as PTZ IP address by setting switch number before any installation. Please refer to
“setting of switch number” in appendix.
11.8.2 Top-down Mounting (Non
standard setting)
1.the mounting position must enable to undertake
the weight of PTZ.
2.Such a mounting way is only suitable for topdown type. Otherwise, it would be water-leaking.
11.8.1 Stand-up Mount Installation
(Standard setting)
Iron plate
1. Installation place must meet the requirements
of wiring safety of 11.2 chapter.
2. Installation pole must be strong and stable,
which is not easy to shake.
Setting switch number of PTZ, setting
baud rate, control protocol and IP address of PTZ
camera according to “setting of switch number” in
appendix of user manual.
Picture11.8-3
Using the bedplate of PTZ as a model to draw the
position of bore which are on the iron plate. (Refer to
Picture 11.8-3) Then fix the top-down PTZ on the
iron plate by M6 screw.
11.8.3 Wall Mount Installation (Non
standard setting)
Iron plate
Pillar
1. Installation position must enable to undertake
high weight pressure, which is 4 times of total
weight of PTZ ,bracket and bedplate.
2.Wall must be strong and stable; bracket must
be ensured to install on clear wall.
Using wall bracket of PTZ as a model to confirm
the position of bores which are on the wall. (Refer
to picture 11.8-4)
Picture11.8-1
Using the bedplate of PTZ as a model to draw the position of bores which are on the iron plate. Then fix the
PTZ on the iron plate by M6 screw. (Refer to picture
11.8-2)
Picture11.8-4
Drill 4 pieces of bores which are M8 metal inflation
bolts in surface of wall ; the depth of bore should be
approximately 75mm, and fixing with M8 inflation
bolts. (Refer to picture 11.8-5)
50
Picture11.8-2
Installation Introduction
Please make video cable, power cable, control cable
and alarm cable penetrated the bracket, and fixed
the bracket stably. Keep enough length of cables:
Video cable should be kept 50 mm out of the bracket ,
and other cables should be kept 80-100 mm from the
bracket.
1
2
3
4
5
6
Red
Yellow
Black
Red “AC24V+ ”
Black “AC24V-”
1. Al arm terminal 2
2. Video connector
3. Al arm terminal 1
4. RS485 terminal
5. Power supply terminal
6.Searchlight power supply
NOTE:5and 6 should connect with a AC24V adaptor individually.
Connection drawing of Searchlight
Picture11.9-2
01Cabling
02Inflation screw
03Bracket
Picture11.8-5
Lock 4 pieces of M8 screw and fix the bracket on the wall,
then smear the glass pastern on the joint side between
wall and the bracket pad which passed the line in order
to prevent the water entering. (Refer to below picture)
Please connect cables refer to the attached tag. Detail
connection refer to below list.
Alarm terminal 1 ：
RED: ALM1
PINK: ALM2
YELLOW: ALM3
Alarm terminal 2 ：
AQUA: NC2
BROWN: NO2
GRAY: ALM7
GREEN: ALM4
BLACK: COM
WHITE: NO
BLUE: NC
PURPLE: ALM6
ORANGE: ALM5
RS485 terminal：
YELLOW:RS485GREEN:RS485+
Power supply terminal：
RED:AC24V+
YELLOW: GROUNDING
BLACK:AC24V-
Glass pastern
11.10 Electrification inspection
Picture 11.8-6
11.9 Cabling Connection
According to different night-vision function, you can refer
to the following connection drawing:
1
2
3
4
5
Red
Yellow
Black
1. Alarm terminal 2
2. Video connector
3. Alarm terminal 1
4. RS485 terminal
5. Power supply terminal
Connect video cable and control cable to the other
equipments; Electrify 24VAC power.
The PTZ carries on self-checking and executes
replacement procedure after power-on.
In the process of self-checking, camera will rotate
horizontally and slowly for one and half cycle to the
default original horizontal point which is set by factory,
then upwardly turn to original vertical point, then
downwardly to original horizontal point. Lens will be
pulled from far focus to near focus to complete selfchecking. The whole camera is absolutely steady means
PTZ completed self-checking and ready to be controlled.
If unstable, please refer to the troubleshooting in the
operation manual appendix.
Connection drawing of Infrared LED
Picture11.9-1
51
Maintenance
12.Maintenance service terms
1. Range of warranty
●
The product will be maintained free for one year.
●
The product will be obtained the free maintenance service if the same malfunction appears again within three
months.
●
Malfunction of products caused by force majeure (such as war, earthquake, lightning strike and so on ), abuse,
non-standard operation, change of construction, non-normal wear or accident are non-free of warranty.
●
Please prevent from the damage which is caused by heavy pressure , the fierce vibration and soaks in the
process of transportation and storage, which does not belong to the free maintenance scope.
●
Please adopt the way of fission package or original package to transport because the product damage dose
not belong to the free maintenance scope if you use the whole packing way , not the original packing way.
●
The maintenance services will not be free when the pan/tilt module is disassembled or serviced by the user
voluntarily.
●
Our company implements the lifetime payable service if the product in malfunction has surpassed the
warranty period.
●
To the products with defect :if it's in the period of warranty, please fill in the form of warranty information
correctly, describe the trouble in details, and provide original sales. invoice or its copy.
●
For the damage and loss which was caused by the user's specifically application, factory won't bear any risk
and responsibility. The factory compensation made by breach of faith, negligence or tortious won't exceed the
amount of the products. The factory won't bear any responsibility for the special, unexpected and continue
damage caused by any other reasons.
●
Our company has the final right of explanation for the above terms.
2. Warranty terms
●
If the products are within the warranty time, the buyer should fill in the warranty card and send back together
with the products.
3. Shipping
●
If the product needs repaired , you can return it to the manufacturer through the supplier or directly. If you
choose the later , please contact us in order to speed up the process. And our company only undertake the
one-way freight from manufacturer to customer after maintenance.
52
AVUE
1180 MIRALOMA WAY SUITE C
SUNNYVALE, CA 94085
WWW.AVUEINC.COM
408.481.9355; [email protected]
Intelligence Heavy-duty PTZ Camera
User Manual
Version V2.11.140430