Black & Decker AS36LN Instruction manual

Powerful Solutions
5
4
6
7
TM
3
2
1
www.blackanddecker.co.uk
AS36LN
English
2
(Original instructions)
5
13
8
9
B
4
11
9
10
C
A
2
6
3
D
E
3
7
7
F1
F2
12
7
F3
G1
12
G2
4
G3
Intended use
Your Black & Decker compact screwdriver has been designed
for screwdriving applications and for drilling in wood, metal,
plastics and masonry. This tool is intended for consumer use
only.
Safety instructions
General power tool safety warnings
@
Warning! Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions listed below may result in electric shock,
fire and/or serious injury.
Save all warnings and instructions for future reference.
The term "power tool" in all of the warnings listed below refers
to your mains operated (corded) power tool or battery
operated (cordless) power tool.
1. Work area safety
a. Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
b. Do not operate power tools in explosive atmospheres,
such as in the presence of flammable liquids, gases
or dust. Power tools create sparks which may ignite the
dust or fumes.
c. Keep children and bystanders away while operating
a power tool. Distractions can cause you to lose control.
2. Electrical safety
a. Power tool plugs must match the outlet. Never modify
the plug in any way. Do not use any adapter plugs
with earthed (grounded) power tools. Unmodified plugs
and matching outlets will reduce risk of electric shock.
b. Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric shock
if your body is earthed or grounded.
c. Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electric shock.
d. Do not abuse the cord. Never use the cord for carrying,
pulling or unplugging the power tool. Keep cord away
from heat, oil, sharp edges or moving parts. Damaged
or entangled cords increase the risk of electric shock.
e. When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a cord
suitable for outdoor use reduces the risk of electric shock.
f. If operating a power tool in a damp location is
unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk of
electric shock.
3. Personal safety
a. Stay alert, watch what you are doing and use common
sense when operating a power tool. Do not use a power
tool while you are tired or under the influence of drugs,
alcohol or medication. A moment of inattention while
operating power tools may result in serious personal injury.
b. Use personal protective equipment. Always wear eye
protection. Protective equipment such as dust mask,
non-skid safety shoes, hard hat, or hearing protection used
for appropriate conditions will reduce personal injuries.
c. Prevent unintentional starting. Ensure the switch is in
the off-position before connecting to power source
and/or battery pack, picking up or carrying the tool.
Carrying power tools with your finger on the switch or
energising power tools that have the switch on invites
accidents.
d. Remove any adjusting key or wrench before turning
the power tool on. A wrench or a key left attached to a
rotating part of the power tool may result in personal injury.
e. Do not overreach. Keep proper footing and balance at
all times. This enables better control of the power tool in
unexpected situations.
f. Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves away
from moving parts. Loose clothes, jewellery or long hair
can be caught in moving parts.
g. If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of dust collection can
reduce dust-related hazards.
4. Power tool use and care
a. Do not force the power tool. Use the correct power
tool for your application. The correct power tool will do
the job better and safer at the rate for which it was designed.
b. Do not use the power tool if the switch does not turn it
on and off. Any power tool that cannot be controlled with
the switch is dangerous and must be repaired.
c. Disconnect the plug from the power source and/or the
battery pack from the power tool before making any
adjustments, changing accessories, or storing power
tools. Such preventive safety measures reduce the risk of
starting the power tool accidentally.
d. Store idle power tools out of the reach of children and
do not allow persons unfamiliar with the power tool or
these instructions to operate the power tool. Power
tools are dangerous in the hands of untrained users.
e. Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and any
other condition that may affect the power tools
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
5
f. Keep cutting tools sharp and clean. Properly maintained
cutting tools with sharp cutting edges are less likely to
bind and are easier to control.
g. Use the power tool, accessories and tool bits etc. in
accordance with these instructions, taking into
account the working conditions and the work to be
performed. Use of the power tool for operations different
from those intended could result in a hazardous situation.
5. Battery tool use and care
a. Recharge only with the charger specified by the
manufacturer. A charger that is suitable for one type of
battery pack may create a risk of fire when used with
another battery pack.
b. Use power tools only with specifically designated
battery packs. Use of any other battery packs may create
a risk of injury and fire.
c. When battery pack is not in use, keep it away from
other metal objects, like paper clips, coins, keys, nails,
screws, or other small metal objects, that can make a
connection from one terminal to another. Shorting the
battery terminals together may cause burns or a fire.
d. Under abusive conditions, liquid may be ejected from
the battery; avoid contact. If contact accidentally
occurs, flush with water. If liquid contacts eyes,
additionally seek medical help. Liquid ejected from the
battery may cause irritation or burns.
6. Service
a. Have your power tool serviced by a qualified repair
person using only identical replacement parts. This will
ensure that the safety of the power tool is maintained.
Additional power tool safety warnings
@
Warning! Additional safety warnings for drills and
impact drills
Wear ear protectors with impact drills. Exposure to
noise can cause hearing loss.
u Use auxiliary handles supplied with the tool. Loss of
control can cause personal injury.
u Hold power tool by insulated gripping surfaces when
performing an operation where the cutting accessory
may contact hidden wiring or its own cord. Cutting
accessory contacting a "live" wire may make exposed
metal parts of the power tool "live" and shock the operator.
u Use clamps or another practical way to secure and
support the workpiece to a stable platform. Holding the
work by hand or against your body leaves it unstable and
may lead to loss of control.
u Before drilling into walls, floors or ceilings, check for the
location of wiring and pipes.
u
6
Avoid touching the tip of a drill bit just after drilling, as it
may be hot.
u The intended use is described in this instruction manual.
The use of any accessory or attachment or performance
of any operation with this tool other than those
recommended in this instruction manual may present
a risk of personal injury and/or damage to property.
u
Safety of others
This appliance is not intended for use by persons
(including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction
concerning use of the appliance by a person responsible
for their safety.
u Children should be supervised to ensure that they do not
play with the appliance.
u
Vibration
The declared vibration emission values stated in the technical
data and the declaration of conformity have been measured in
accordance with a standard test method provided by
EN 60745 and may be used for comparing one tool with
another. The declared vibration emission value may also be
used in a preliminary assessment of exposure.
Warning! The vibration emission value during actual use of
the power tool can differ from the declared value depending
on the ways in which the tool is used. The vibration level may
increase above the level stated.
When assessing vibration exposure to determine safety
measures required by 2002/44/EC to protect persons regularly
using power tools in employment, an estimation of vibration
exposure should consider, the actual conditions of use and the
way the tool is used, including taking account of all parts of
the operating cycle such as the times when the tool is
switched off and when it is running idle in addition to the
trigger time.
Labels on tool
:
The following pictograms are shown on the tool:
Warning! To reduce the risk of injury, the user must
read the instruction manual.
Additional safety instructions for batteries and
chargers
Batteries
u Never attempt to open for any reason.
u Do not expose the battery to water.
u Do not expose the battery to heat.
Do not store in locations where the temperature may
exceed 40 °C.
u Charge only at ambient temperatures between 10 °C and
40 °C.
u Charge only using the charger provided with the
appliance/tool. Using the wrong charger could result in an
electric shock or overheating of the battery.
u When disposing of batteries, follow the instructions given
in the section "Protecting the environment".
u Do not damage/deform the battery either by puncture or
impact, as this may create a risk of injury and fire.
u Do not charge damaged batteries.
u Under extreme conditions, battery leakage may occur.
When you notice liquid on the batteries carefully wipe the
liquid off using a cloth. Avoid skin contact.
u In case of skin or eye contact, follow the instructions below.
Warning! The battery fluid may cause personal injury or
damage to property. In case of skin contact, immediately rinse
with water. If redness, pain or irritation occurs seek medical
attention. In case of eye contact, rinse immediately with clean
water and seek medical attention.
Charge only at ambient temperatures between
10 °C and 40 °C.
u
Chargers
Your charger has been designed for a specific voltage.
Always check that the mains voltage corresponds to the
voltage on the rating plate.
Warning! Never attempt to replace the charger unit with
a regular mains plug.
u Use your Black & Decker charger only to charge the
battery in the tool with which it was supplied. Other
batteries could burst, causing personal injury and damage.
u Never attempt to charge non-rechargeable batteries.
u If the supply cord is damaged, it must be replaced by the
manufacturer or an authorised Black & Decker Service
Centre in order to avoid a hazard.
u Do not expose the charger to water.
u Do not open the charger.
u Do not probe the charger.
u The appliance/tool/battery must be placed in a well
ventilated area when charging.
$
+
The charger is intended for indoor use only.
-
Read the instruction manual before use.
The charger automatically shuts off if the ambient
temperature becomes too high. As soon as the
ambient temperature has cooled down, the charger
will resume operating.
y
Charging
Electrical safety
#
Your charger is double insulated; therefore no earth
wire is required. Always check that the mains voltage
corresponds to the voltage on the rating plate.
If the supply cord is damaged, it must be replaced by the
manufacturer or an authorised Black & Decker Service
Centre in order to avoid a hazard.
u Warning! Never attempt to replace the charger unit with a
regular mains plug.
u
Features
1. On/off switch
2. Forward/reverse slider
3. Forward/reverse window
4. Bit holder
5. LED light
6. Mode selector / torque adjustment collar
7. Screw holder
Fig. A
8. Charger
9. Charging base
10. Charging indicator
11. Bit storage
Assembly
Fitting the charging base to the wall (fig. A & B)
The charging base (9) can be placed on a worktop or fitted to
the wall to provide a convenient storage and charging point for
the tool. Screws and wall anchors are not included.
u Drive screws in the wall with the same distance apart as
the slots (13) on the back of the charging base (9).
The distance between the slots must be 75 mm.
u Slide the charging base over the screws to fit the base to
the wall.
u Plug in the charger (8).
u Place the tool on the charging base making sure the
charging indicator (10) lights up.
Warning! Avoid damaging the power cord when mounting the
charging base to the wall.
7
Fitting and removing a drill bit or a screwdriver bit
(fig. C)
This tool uses screwdriver bits and drill bits with a 6.35 mm
(1/4") hexagonal shank.
u To fit a bit, insert the bit shaft into the bit holder (4).
u To remove a bit, pull the bit shaft out of the bit holder (4).
Residual risks.
Additional residual risks may arise when using the tool which
may not be included in the enclosed safety warnings. These
risks can arise from misuse, prolonged use etc.
Even with the application of the relevant safety regulations
and the implementation of safety devices, certain residual
risks can not be avoided. These include:
u Injuries caused by touching any rotating/moving
parts.
u Injuries caused when changing any parts, blades or
accessories.
u Injuries caused by prolonged use of a tool. When
using any tool for prolonged periods ensure you take
regular breaks.
u Impairment of hearing.
u Health hazards caused by breathing dust developed
when using your tool (example:- working with wood,
especially oak, beech and MDF.)
Use
Warning! Let the tool work at its own pace. Do not overload.
u Before first use, the battery must be charged for at least
9 hours.
Charging the battery (fig. A)
Place the tool on the charging base (9).
Plug in the charger (8).
u Leave the tool connected to the charger for 6 hours.
The red light illuminates when the unit is on charge and will
stay red as long as there is power to the charger. The red light
will not go off to indicate a full charge.
u
u
The charger may hum and become warm while charging;
this is normal and does not indicate a problem.
Warning! Do not charge the battery at ambient temperatures
below 4 °C or above 40 °C.
Selecting the direction of rotation (fig. D)
For drilling and for tightening screws, use forward (clockwise)
rotation. For loosening screws or removing a jammed drill bit,
use reverse (counterclockwise) rotation.
The forward/reverse window (3) displays the rotation direction
with an arrow.
8
To select forward rotation, push the forward/reverse slider
(2) to the forward position.
u To select reverse rotation, push the forward/reverse slider
(2) to the rearward position.
u To lock the tool, set the forward/reverse slider into the
centre position.
u
Selecting the torque (fig. E)
This tool is fitted with a collar to set the torque for various
screwdriving and drilling applications. Large screws and hard
workpiece materials require a higher torque setting than small
screws and soft workpiece materials. The collar has a range
of 6 settings to suit your application.
u To set the torque, rotate the torque adjustment collar (6)
clockwise or counterclockwise.
u For screwdriving, set the collar to the desired setting.
If you do not yet know the appropriate setting, proceed as
follows:
- Set the collar (6) to the lowest torque setting.
- Tighten the first screw.
- If the clutch ratchets before the desired result is
achieved, increase the collar setting and continue
tightening the screw. Repeat until you reach the correct
setting. Use this setting for the remaining screws.
Screwdriving applications
Torque range: low torque for small screws and
high torque for large screws
Drilling/screwdriving
Select forward or reverse rotation using the forward/
reverse slider (2).
u To switch the tool on, press the on/off switch (1).
u To switch the tool off, release the on/off switch (1).
u
Screwdriving using the screw holder (fig. F1 - F3)
The screw holder (7) can be used with 1" and 2" screwdriver
bits. The screw holder cannot be used with bit tip holder
extensions.
u Pull the screw holder (7) out the tool (fig. F1).
u Place the screw onto the screw holder (fig. F2).
u Push the screw holder towards the screw making sure the
bit tip and the screw are fully engaged (fig. F3).
The screw is securely held to the screw holder with a magnet.
The magnet does not work on non-ferrous screws.
u Drive the screw into the wall.
When screwdriving, the screw holder retracts in order to allow
the screw to be driven to its required depth.
LED light
Drive the cutter on the drill bit as far into the material as
necessary. Cut away sufficient material to sink the screw
head into the material (fig. G2).
u Drive the screw into the material with a screwdriver bit
(fig. G3).
u
The LED light (5) is activated automatically when the trigger is
depressed. The LED will also illuminate when the trigger is
depressed and the forward/reverse slider (2) is in the locked
off position (central position).
Accessories
Hints for optimum use
Screwdriving
u Always use the correct type and size of screwdriver bit.
u If screws are difficult to tighten, try applying a small
amount of washing liquid or soap as a lubricant.
u Use the spindle lock to loosen very tight screws or to
firmly tighten screws.
u Always hold the tool and screwdriver bit in a straight line
with the screw.
u When screwing in wood, it is recommended to drill a pilot
hole with a depth equal to the length of the screw. A pilot
hole guides the screw and prevents splintering or
distortion of the wood. For the optimum size of the pilot
hole, refer to the table below.
u When screwing in hardwood, also drill a clearance hole
with a depth equal to half the length of the screw. For the
optimum size of the clearance hole, refer to the table
below.
Screw size
Pilot hole ø
Pilot hole ø
Clearance
(softwood)
(hardwood)
hole
No. 6 (3.5 mm)
2.0 mm
2.5 mm
3.6 mm
No. 8 (4 mm)
2.5 mm
3.0 mm
4.5 mm
No. 10 (5 mm)
3.0 mm
3.5 mm
5.0 mm
Drilling
u Always apply a light pressure in a straight line with the drill
bit.
u Just before the drill tip breaks through the other side of the
workpiece, decrease pressure on the tool.
u Use a block of wood to back up workpieces that may
splinter.
u Make an indentation using a centre punch at the centre of
the hole to be drilled in order to improve accuracy.
Drilling using a countersink drill bit (fig. G1 - G3)
The countersink drill bit (12) is used to remove material to seat
the screw head flush to the surface.
Warning! Always gear the diameter of the drill bit to the
diameter of the screw.
u Place the drill bit into the tool.
u Drive the drill into the material (fig. G1).
The performance of your tool depends on the accessory used.
Black & Decker and Piranha accessories are engineered to
high quality standards and designed to enhance the
performance of your tool. By using these accessories you will
get the very best from your tool.
This tool uses screwdriver bits with a 1/4" (6.35 mm)
hexagonal shank. Piranha Super-lok accessories are
designed for use with this tool.
Maintenance
Your Black & Decker corded/cordless appliance/tool has been
designed to operate over a long period of time with a minimum
of maintenance. Continuous satisfactory operation depends
upon proper tool care and regular cleaning.
Warning! Before performing any maintenance on corded/
cordless power tools:
u Switch off and unplug the appliance/tool.
u Or switch off and remove the battery from the appliance/
tool if the appliance/tool has a separate battery pack.
u Or run the battery down completely if it is integral and then
switch off.
u Unplug the charger before cleaning it. Your charger does
not require any maintenance apart from regular cleaning.
u Regularly clean the ventilation slots in your appliance/tool/
charger using a soft brush or dry cloth.
u Regularly clean the motor housing using a damp cloth.
Do not use any abrasive or solvent-based cleaner.
u Regularly open the chuck and tap it to remove any dust
from the interior (when fitted).
Protecting the environment
Z
Separate collection. This product must not be
disposed of with normal household waste.
Should you find one day that your Black & Decker product
needs replacement, or if it is of no further use to you, do not
dispose of it with household waste. Make this product
available for separate collection.
9
z
Separate collection of used products and packaging
allows materials to be recycled and used again.
Re-use of recycled materials helps prevent
environmental pollution and reduces the demand for
raw materials.
Local regulations may provide for separate collection of
electrical products from the household, at municipal waste
sites or by the retailer when you purchase a new product.
Black & Decker provides a facility for the collection and
recycling of Black & Decker products once they have reached
the end of their working life. To take advantage of this service
please return your product to any authorised repair agent who
will collect them on our behalf.
You can check the location of your nearest authorised repair
agent by contacting your local Black & Decker office at the
address indicated in this manual. Alternatively, a list of
authorised Black & Decker repair agents and full details of our
after-sales service and contacts are available on the Internet
at: www.2helpU.com
Batteries
h
Technical data
Voltage
VDC
No-load speed
min-1
Max. torque
Nm
Bit holder
mm
Weight
kg
Battery
Voltage
V 3.6
Battery type Li-Ion
AHr rating 1.1
Charger
Input voltage
Approx. charging time
Weight
VAC 230
h 6-9
kg 0.4
Level of sound pressure according to EN 60745:
Sound pressure (LpA) 63.1 dB(A), uncertainty (K) 3 dB(A)
Acoustic power (LWA) 73.1 dB(A), uncertainty (K) 3 dB(A)
Vibration total values (triax vector sum) according to EN 60745:
Drilling into metal (ah, D) 1.911 m/s2, uncertainty (K) 1.5 m/s2
Screwdriving without impact (ah, S) 0.549 m/s2, uncertainty (K) 1.5 m/s2
Black & Decker batteries can be recharged many
times. At the end of their useful life, discard batteries
with due care for our environment:
Do not short-circuit the battery terminals.
Do not dispose of the battery(s) in a fire as this may result
in a risk of personal injury or an explosion.
u Run the battery down completely, then remove it from the
tool.
u Batteries are recyclable. Place the battery(s) in a suitable
packaging to ensure that the terminals cannot be
short-circuited. Take them to any authorised repair agent
or a local recycling station.
AS36LN H1
3.6
180
4.3
6.35 (1/4")
0.4
EC declaration of conformity
%
MACHINERY DIRECTIVE
u
AS36LN
u
Black & Decker declares that these products described under
"technical data" are in compliance with:
98/37/EC (until Dec. 28, 2009), 2006/42/EC
(from Dec. 29, 2009), EN 60745-1, EN 60745-2-2
For more information, please contact Black & Decker at the
following address or refer to the back of the manual.
_
The undersigned is responsible for compilation of the technical
file and makes this declaration on behalf of Black & Decker.
10
Kevin Hewitt
Vice-President Global Engineering
Black & Decker Europe, 210 Bath Road, Slough,
Berkshire, SL1 3YD
United Kingdom
21-12-2009
Guarantee
Black & Decker is confident of the quality of its products and
offers an outstanding guarantee. This guarantee statement is
in addition to and in no way prejudices your statutory rights.
The guarantee is valid within the territories of the Member
States of the European Union and the European Free Trade
Area.
If a Black & Decker product becomes defective due to faulty
materials, workmanship or lack of conformity, within 24 months
from the date of purchase, Black & Decker guarantees to
replace defective parts, repair products subjected to fair wear
and tear or replace such products to ensure minimum
inconvenience to the customer unless:
u The product has been used for trade, professional or hire
purposes;
u The product has been subjected to misuse or neglect;
u The product has sustained damage through foreign
objects, substances or accidents;
u Repairs have been attempted by persons other than
authorised repair agents or Black & Decker service staff.
To claim on the guarantee, you will need to submit proof of
purchase to the seller or an authorised repair agent. You can
check the location of your nearest authorised repair agent by
contacting your local Black & Decker office at the address
indicated in this manual. Alternatively, a list of authorised
Black & Decker repair agents and full details of our after-sales
service and contacts are available on the Internet at:
www.2helpU.com
Please visit our website www.blackanddecker.co.uk to
register your new Black & Decker product and to be kept up to
date on new products and special offers. Further information
on the Black & Decker brand and our range of products is
available at www.blackanddecker.co.uk
11
TYP.
H1
AS36LN
Partial support - Only parts shown available
Nur die aufgefuerten teile sind lieferbar
Reparation partielle - Seules les pieces indiquees sont disponibles
Supporto parziale - Sono disponibili soltanto le parti evidenziate
Solo estan disponibles las peizas listadas
So se encontram disponiveis as pecas listadas
Gedeeltelijke ondersteuning - alleen de getoonde onderdelen
zijn beschikbaar
1
2
E15386
12
www.2helpU.com
23 - 09 - 09
13
14
ENGLISH
Do not forget to register your product!
www.blackanddecker.co.uk/productregistration
Register your product online at www.blackanddecker.co.uk/productregistration or send your name, surname and product
code to Black & Decker in your country.
Australia
Black & Decker (Australia) Pty. Ltd.
20 Fletcher Road, Mooroolbark, Victoria, 3138
New Zealand
Black & Decker
5 Te Apunga Place
Mt Wellington
Auckland 1060
United Kingdom
Black & Decker
210 Bath Road
Slough, Berkshire SL1 3YD
90557368 REV-1
Tel. 03-8720 5100
Fax 03-9727 5940
Tel. +64 9 259 1133
Fax +64 9 259 1122
Tel. 01753 511234
Fax 01753 551155
Helpline 01753 574277
12/2009