Sharp PN-V600 Operation Instruction manual

PN-V600
LCD MONITOR
OPERATION MANUAL
IMPORTANT:
To aid reporting in case of loss or theft, please record the
product’s model and serial numbers in the space provided.
The numbers are located in the rear of the product.
Model No.:
Serial No.:
U.S.A. ONLY
FOR CUSTOMERS IN U.K.
IMPORTANT
The wires in this mains lead are coloured in accordance with the following code:
GREEN-AND-YELLOW:
Earth
BLUE:
Neutral
BROWN:
Live
As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the
terminals in your plug proceed as follows:
•The wire which is coloured GREEN-AND-YELLOW must be connected to the terminal in the plug which is marked by the
letter E or by the safety earth or coloured green or green-and-yellow.
•The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured black.
•The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured red.
Ensure that your equipment is connected correctly. If you are in any doubt consult a qualified electrician.
“WARNING: THIS APPARATUS MUST BE EARTHED.”
Authorised representative responsible for the European Union Community Market
SHARP ELECTRONICS (Europe) GmbH
Sonninstraße 3, D-20097 Hamburg
IMPORTANT INFORMATION
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT
TO RAIN OR MOISTURE.
CAUTION
RISK OF ELECTRIC
SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER.
NO USER-SERVICEABLE PARTS
INSIDE.
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within
an equilateral triangle, is intended to alert the
user to the presence of uninsulated “dangerous
voltage” within the product’s enclosure that may
be of sufficient magnitude to constitute a risk of
electric shock to persons.
The exclamation point within a triangle is
intended to alert the user to the presence of
important operating and maintenance (servicing)
instructions in the literature accompanying the
product.
WARNING:
FCC Regulations state that any unauthorized changes or modifications to this equipment not expressly approved by the
manufacturer could void the user’s authority to operate this equipment.
NOTE:
This equipment has been tested and found to comply with the limits for Class A digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment
is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required
to correct the interference at his own expense.
This product utilizes a CR coin Lithium battery which contains a Perchlorate material.
Special handling for this material may apply,
California residents, See www.dtsc.ca.gov/hazardouswaste/perchlorate/
Others, consult local environmental officers.
U.S.A. ONLY
3
E
IMPORTANT INFORMATION (Continued)
Attention: Your product is marked with this symbol. It means that used electrical and electronic products
should not be mixed with general household waste. There is a separate collection system for these products.
EU ONLY
A. Information on Disposal for Users (private households)
1. In the European Union
Attention: If you want to dispose of this equipment, please do not use the ordinary dustbin!
Used electrical and electronic equipment must be treated separately and in accordance with legislation that requires proper
treatment, recovery and recycling of used electrical and electronic equipment.
Following the implementation by member states, private households within the EU states may return their used electrical and
electronic equipment to designated collection facilities free of charge*. In some countries* your local retailer may also take
back your old product free of charge if you purchase a similar new one.
*) Please contact your local authority for further details.
If your used electrical or electronic equipment has batteries or accumulators, please dispose of these separately beforehand
according to local requirements.
By disposing of this product correctly you will help ensure that the waste undergoes the necessary treatment, recovery and
recycling and thus prevent potential negative effects on the environment and human health which could otherwise arise due
to inappropriate waste handling.
2. In other Countries outside the EU
If you wish to discard this product, please contact your local authorities and ask for the correct method of disposal.
For Switzerland: Used electrical or electronic equipment can be returned free of charge to the dealer, even if you don’t
purchase a new product. Further collection facilities are listed on the homepage of www.swico.ch or www.sens.ch.
B. Information on Disposal for Business Users
1. In the European Union
If the product is used for business purposes and you want to discard it:
Please contact your SHARP dealer who will inform you about the take-back of the product. You might be charged for the
costs arising from take-back and recycling. Small products (and small amounts) might be taken back by your local collection
facilities.
For Spain: Please contact the established collection system or your local authority for take-back of your used products.
2. In other Countries outside the EU
If you wish to discard of this product, please contact your local authorities and ask for the correct method of disposal.
EU ONLY
The battery supplied with this product contains traces of Lead.
For EU:
The crossed-out wheeled bin implies that used batteries should not be put to the general household
waste! There is a separate collection system for used batteries, to allow proper treatment and recycling in
accordance with legislation. Please contact your local authority for details on the collection and recycling
schemes.
For Switzerland:
The used battery is to be returned to the selling point.
For other non-EU countries:
Please contact your local authority for correct method of disposal of the used battery.
“BATTERY DISPOSAL”
THIS PRODUCT CONTAINS A LITHIUM PRIMARY (MANGANESS DIOXIDE) MEMORY BACK-UP BATTERY THAT
MUST BE DISPOSED OF PROPERLY. PLEASE CONTACT YOUR LOCAL SHARP DEALER OR AUTHORIZED SERVICE
REPRESENTATIVE FOR ASSISTANCE IN DISPOSING OF THIS BATTERY.
U.S.A. AND CANADA ONLY
E
4
DEAR SHARP CUSTOMER
Thank you for your purchase of a SHARP LCD product. To ensure safety and many years of trouble-free operation of your
product, please read the Safety Precautions carefully before using this product.
SAFETY PRECAUTIONS
Electricity is used to perform many useful functions, but it can also cause personal injuries and property damage if improperly
handled. This product has been engineered and manufactured with the highest priority on safety. However, improper use can
result in electric shock and/or fire. In order to prevent potential danger, please observe the following instructions when installing,
operating and cleaning the product. To ensure your safety and prolong the service life of your LCD product, please read the
following precautions carefully before using the product.
1. Read instructions — All operating instructions must be read and understood before the product is operated.
2. K
eep this manual in a safe place — These safety and operating instructions must be kept in a safe place for future
reference.
3. Observe warnings — All warnings on the product and in the instructions must be observed closely.
4. Follow instructions — All operating instructions must be followed.
5. Cleaning — Unplug the power cord from the AC outlet before cleaning the product. Use a dry cloth to clean the product. Do
not use liquid cleaners or aerosol cleaners.
6. Attachments — Do not use attachments not recommended by the manufacturer. Use of inadequate attachments can result
in accidents.
7. Water and moisture — Do not use the product near water. Do not install the product in a place where water may splash onto
it. Be careful of equipment which drains water such as an air-conditioner.
8. Ventilation — The vents and other openings in the cabinet are designed for ventilation.
Do not cover or block these vents and openings since insufficient ventilation can cause overheating and/or shorten the life
of the product. Do not place the product on a sofa, rug or other similar surface, since they can block ventilation openings.
Do not place the product in an enclosed place such as a bookcase or rack, unless proper ventilation is provided or the
manufacturer’s instructions are followed.
9. Power cord protection — The power cords must be routed properly to prevent people from stepping on them or objects from
resting on them.
10. The LCD panel used in this product is made of glass. Therefore, it can break when the product is dropped or applied with
impact. Be careful not to be injured by broken glass pieces in case the LCD panel breaks.
11. Overloading — Do not overload AC outlets or extension cords. Overloading can cause fire or electric shock.
12. Entering of objects and liquids — Never insert an object into the product through vents or openings. High voltage flows in
the product, and inserting an object can cause electric shock and/or short internal parts.
For the same reason, do not spill water or liquid on the product.
13. Servicing — Do not attempt to service the product yourself. Removing covers can expose you to high voltage and other
dangerous conditions. Request a qualified service person to perform servicing.
14. Repair — If any of the following conditions occurs, unplug the power cord from the AC outlet, and request a qualified service
person to perform repairs.
a. When the power cord or plug is damaged.
b. When a liquid was spilled on the product or when objects have fallen into the product.
c. When the product has been exposed to rain or water.
d. When the product does not operate properly as described in the operating instructions.
Do not touch the controls other than those described in the operating instructions. Improper adjustment of controls
not described in the instructions can cause damage, which often requires extensive adjustment work by a qualified
technician.
e. When the product has been dropped or damaged.
f. When the product displays an abnormal condition. Any noticeable abnormality in the product indicates that the product
needs servicing.
15. Replacement parts — In case the product needs replacement parts, make sure that the service person uses replacement
parts specified by the manufacturer, or those with the same characteristics and performance as the original parts. Use of
unauthorized parts can result in fire, electric shock and/or other danger.
16. Safety checks — Upon completion of service or repair work, request the service technician to
perform safety checks to ensure that the product is in proper operating condition.
17. Wall mounting — When mounting the product on a wall, be sure to install the product according to the method
recommended by the manufacturer.
18. Heat sources — Keep the product away from heat sources such as radiators, heaters, stoves and other heat-generating
products (including amplifiers).
5
E
SAFETY PRECAUTIONS (Continued)
9. Batteries — Incorrect use of batteries may cause the batteries to burst or ignite. A leaky battery may corrode the equipment,
1
dirty your hands or spoil your clothing. In order to avoid these problems, make sure to observe the precautions below:
• Use the specified batteries only.
• Install the batteries with due attention to the plus (+) and minus (-) sides of the batteries according to the instructions in the
compartment.
• Do not mix old and new batteries.
• Do not mix batteries of different types. Voltage specifications of batteries of the same shape may vary.
• Replace an exhausted battery with a new one promptly.
• If you will not use the remote control for a long time, remove the batteries.
• If leaked battery fluid gets on your skin or clothing, rinse immediately and thoroughly. If it gets into your eye, bathe your
eye well rather than rubbing and seek medical treatment immediately. Leaked battery fluid that gets into your eye or your
clothing may cause a skin irritation or damage your eye.
20. Usage of the monitor must not be accompanied by fatal risks or dangers that, could lead directly to death, personal injury,
severe physical damage or other loss, including nuclear reaction control in nuclear facility, medical life support system, and
missile launch control in a weapon system.
21. Do not stay in contact with the parts of the product that become hot for long periods of time. Doing so may result in
low-temperature burns.
WARNING:
This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be
required to take adequate counter measures.
To maintain compliance with EMC regulations, use shielded cables to connect to the following terminals: PC/AV DVI-D output
terminal, PC/AV DVI-D input terminal, PC/AV HDMI input terminal, PC D-SUB input terminal, PC RGB input terminals, and
RS-232C input/output terminals.
If a monitor is not positioned in a sufficiently stable location, it can be potentially hazardous due to falling. Many injuries,
particularly to children, can be avoided by taking simple precautions such as:
• Using fixing devices like wall mount brackets recommended by the manufacturer.
• Only using furniture that can safely support the monitor.
• Ensuring the monitor is not overhanging the edge of the supporting furniture.
• Not placing the monitor on tall furniture (for example, cupboards or bookcases) without anchoring both the furniture and the
monitor to a suitable support.
• Not standing the monitors on cloth or other materials placed between the monitor and supporting furniture.
• Educating children about the dangers of climbing on furniture to reach the monitor or its controls.
Especially for child safety
- Don’t allow children to climb on or play with the monitor.
- Don’t place the monitor on furniture that can easily be used as steps, such as a chest of drawers.
- Remember that children can become excited while watching a program, especially on a “larger than life” monitor. Care
should be taken to place or install the monitor where it cannot be pushed, pulled over, or knocked down.
- Care should be taken to route all cords and cables connected to the monitor so that they cannot be pulled or grabbed by
curious children.
E
6
TIPS AND SAFETY INSTRUCTIONS
- The TFT color LCD panel used in this monitor is made with
the application of high precision technology. However, there
may be minute points on the screen where pixels never light
or are permanently lit. Also, if the screen is viewed from
an acute angle there may be uneven colors or brightness.
Please note that these are not malfunctions but common
phenomena of LCDs and will not affect the performance of
the monitor.
- Do not display a still picture for a long period, as this could
cause a residual image.
- Never rub or tap the monitor with hard objects.
- Please understand that SHARP CORPORATION bears no
responsibility for errors made during use by the customer or
a third party, nor for any other malfunctions or damage to this
product arising during use, except where indemnity liability is
recognized under law.
- This monitor and its accessories may be upgraded without
advance notice.
- Do not use the monitor where there is a lot of dust, where
humidity is high, or where the monitor may come into contact
with oil or steam, as this could lead to fire.
- Ensure that the monitor does not come into contact with
water or other fluids. Ensure that no objects such as paper
clips or pins enter the monitor as this could lead to fire or
electric shock.
- Do not place the monitor on top of unstable objects or in
unsafe places. Do not allow the monitor to receive strong
shocks or to strongly vibrate. Causing the monitor to fall or
topple over may damage it.
- Do not use the monitor near heating equipment or in places
where there is likelihood of high temperature, as this may
lead to generation of excessive heat and outbreak of fire.
- Do not use the monitor in places where it may be exposed to
direct sunlight.
- If the monitor is installed in a location exposed to sunlight
such as next to a window, measures to reduce ultraviolet and
infrared radiation and temperature measures are required.
For details, consult your dealer.
- Please be sure to constantly remove dust and garbage that
has attached to the ventilation opening. If dust collects in the
ventilation opening, it may lead to excessive heat, outbreak
of fire, or malfunction.
As a standard, clean the inside of the monitor once every
year. If dust collects inside the monitor, it may lead to
excessive heat, outbreak of fire, or malfunction. Please
request a cleaning of the inside of the monitor from an
authorized SHARP servicing dealer or service center.
- Images cannot be rotated on this monitor.
When using in portrait orientation, you will need to prepare
appropriately orientated content in advance.
- The AC outlet shall be installed near the equipment and shall
be easily accessible.
The Power Cord
- Do not remove or insert the power plug with wet hands.
Doing so could result in electric shock.
- Unplug the power cord if it is not used for a long time.
- Do not attempt to repair the power cord if it is broken
or malfunctioning. Refer the servicing to the service
representative.
Manual Scope
- Microsoft, Windows and Internet Explorer are registered
trademarks of Microsoft Corporation.
- HDMI, the HDMI logo and High-Definition Multimedia
Interface are trademarks or registered trademarks of HDMI
Licensing LLC.
- Adobe, Acrobat, and Reader are either registered trademarks
or trademarks of Adobe Systems Incorporated in the United
States and/or other countries.
- This product comes with RICOH Bitmap Fonts produced and
sold by RICOH COMPANY, LTD.
- All other brand and product names are trademarks or
registered trademarks of their respective holders.
- Language of OSD menu used in this manual is English by
way of example.
- Illustrations in this manual may not exactly represent the
actual product or display.
- This manual assumes use in landscape orientation, except
where specifically noted.
- This manual assumes that this product will be used with
the remote control unit buttons, except where specifically
noted. Operation by using the buttons on the rear side of the
product will perform the same functions.
Rear side buttons
Remote control
unit buttons
* For operation with the remote control unit, the PN-ZR01
control kit (optional) is required.
LED Backlight
● The LED backlight in this product has a limited lifetime.
* If the screen gets dark or does not turn on, it may be
necessary to replace the LED backlight. This LED
backlight is exclusive to this product and must be replaced
by an authorized Sharp servicing dealer or service center.
* Please contact your local Sharp servicing dealer or
service center for assistance.
Fan
● The fan in this product has a limited lifetime.
- Use only the power cord supplied with the monitor.
- Do not damage the power cord nor place heavy objects on
it, stretch it or over bend it. Also, do not add extension cords.
Damage to the cord may result in fire or electric shock.
- Do not use the power cord with a power tap.
Adding an extension cord may lead to fire as a result of
overheating.
7
E
MOUNTING PRECAUTIONS
• This product is for use indoors.
• A mounting bracket compliant with VESA specifications is
required.
• Since the monitor is heavy, consult your dealer before
installing, removing or moving the monitor.
• Mounting the monitor on the wall requires special expertise
and the work must be performed by an authorized SHARP
dealer. You should never attempt to perform any of this
work yourself. Our company will bear no responsibility
for accidents or injuries caused by improper mounting or
mishandling.
• Use the monitor perpendicular to a level surface. If
necessary, the monitor may be tilted up to 20 degrees
upward or downward.
• When mounting the monitor horizontally, the optional fan
cover (PN-ZR31) is required. For details along with the
horizontal mounting conditions, consult your dealer.
• This monitor should be used at an ambient temperature
between 32°F (0°C) and 104°F (40°C).
• Be careful of high temperatures in the surrounding area.
When installing the monitor inside a housing, or if the
ambient temperature may be outside of the range of 32ºF
(0ºC) to 104ºF (40ºC), install a fan or take other measures
to keep the ambient temperature within the required range.
• Temperature condition may change when using the monitor
together with the optional equipments recommended by
SHARP. In such cases, please check the temperature
condition specified by the optional equipments.
• Do not block any ventilation openings. If the temperature
inside the monitor rises, this could lead to a malfunction.
• Do not place the monitor on a device which generates heat.
E
8
• Adhere to the following when installing the monitor in its
portrait orientation. Failing to adhere to the following may
cause malfunctions.
- To install in landscape orientation, rotate the monitor 90
degrees to the right.
- Set the MONITOR on the SETUP menu to PORTRAIT.
(See page 24.)
- Be sure to secure the power cord (supplied) to the cable
clamp attachment with the supplied cable clamp.
Make sure that the power cord (supplied) does not supply
power to the terminal when being secured and do not
over bend the power cord (supplied).
Power cord (Supplied)
Cable clamp
attachment
Cable clamp
Contents
IMPORTANT INFORMATION.............................................3
DEAR SHARP CUSTOMER...............................................5
SAFETY PRECAUTIONS...................................................5
TIPS AND SAFETY INSTRUCTIONS................................7
MOUNTING PRECAUTIONS.............................................8
Supplied Components......................................................9
Part Names......................................................................10
Connecting Peripheral Equipment................................12
Multiple monitor connection........................................13
Preparing the Remote Control Unit...............................15
Installing the batteries.................................................15
Remote control operation range..................................15
Connecting the Power Cord..........................................15
Binding Cables................................................................16
Removing the Handles...................................................16
Affixing the Protection Covers......................................16
Turning Power On/Off.....................................................17
Turning on the main power.........................................17
Turning power on/off...................................................17
Disabling power on/off operations...............................17
Basic Operation..............................................................18
Remote Control Mode ...................................................21
Menu Items......................................................................22
Displaying the menu screen........................................22
Menu item details........................................................23
Adjustments for PC screen display.............................30
Initialization (Reset)/Functional Restriction Setting
(FUNCTION).....................................................................31
Controlling the Monitor with a PC (RS-232C)...............32
PC connection.............................................................32
Communication conditions..........................................32
Communication procedure..........................................32
Setting of the GAMMA user data.................................36
RS-232C command table............................................37
Controlling the Monitor with a PC (LAN)......................45
Settings to connect to a LAN.......................................45
Controlling with a PC...................................................47
Troubleshooting..............................................................53
Specifications.................................................................55
Mounting Precautions (For SHARP dealers and
service engineers)..........................................................60
Supplied Components
If any component should be missing, please contact your dealer.
 Liquid Crystal Display Monitor: 1
 Cable clamp: 2
 Power cord: 1
 CD-ROM (Utility Disk for Windows): 1
 Setup manual: 1
 Protection cover: 4
 Handle screw (short): 4
 Bezel sheet (long/short): 2 each
 Bezel sheet attachment instructions: 1
* Sharp Corporation holds authorship rights to the Utility Disk program. Do not reproduce it without permission.
* For environmental protection!
Do not dispose of batteries in household waste. Follow the disposal instructions for your area.
9
E
Part Names
nFront view
1
1. LCD panel
2. INPUT button
3. MENU button
4. VOL -/Cursor control ( ) button
5. VOL +/Cursor control ( ) button
6. BRIGHT -/Cursor control ( ) button
7. BRIGHT +/Cursor control ( ) button
8. Power button
9. Power LED
The rear buttons if seen
from the front
2
3
4
6
5
nRear view
7
8
9
10
11
12
12
13
14
15
16
17 18 19 20 21 23
22 24
When the PN-ZB02
(optional) is attached
25
26 27 28 29 30 31 33 34
32
9
8
7
6
5
4
3
2
Caution
• Consult your SHARP dealer for attachment/detachment of
optional parts.
• Do not block the fan cover.
• Do not open the expansion terminal cover by yourself.
There are high voltage parts inside the cover which may
cause an electric shock.
E
10
0. Fan/Fan cover
1
11. Vents
12. Handles
13. Expansion terminal cover
Additional input/output terminals are available by attaching
the PN-ZB02 interface expansion board (optional).
14. Optional attachment section
This section is used to connect optional hardware for
function expansion. Offering this attachment location
is not a guarantee that future compatible hardware
attachments will be released.
15. AC input terminal
16. Main power switch
17. PC/AV HDMI input terminal
18. PC D-sub input terminal
19. Audio input terminal
20. Audio output terminals
21. RS-232C output terminal
22. RS-232C input terminal
23. Optional terminal
This terminal is provided for possible future (optional)
function expansion. Offering of this terminal is not a
guarantee that future expanded functionality will be
provided.
24. Control kit terminal
When the PN-ZB02 (optional) is attached
25. PC/AV DVI-D input terminal
26. PC/AV DVI-D output terminal
27. LAN terminal
28. External speaker terminals
29. Audio 1 input terminals
30. Audio 2 input terminals
31. PC RGB input terminals
32. AV component input terminals
33. AV video input terminal
34. AV S-video input terminal
Part Names
Remote control unit
n
(Supplied with the PN-ZR01 (optional))
1
2
8
3
9
4
5
10
11
6
1. Signal transmitter
2. POWER button
3. MUTE button
4. VOL +/Cursor control ( ) button
5. BRIGHT -/Cursor control ( ) button
6. DISPLAY button
7. MODE button
8. INPUT button
9. MENU button
10. BRIGHT +/Cursor control ( ) button
11. VOL -/Cursor control ( ) button
12. SIZE button
12
7
Remote control sensor box
n
(Supplied with the PN-ZR01 (optional))
1
2
4
1.
2.
3.
4.
Brightness sensor
Remote control sensor
Connection cable
Mounting bracket
3
11
E
Connecting Peripheral Equipment
1. PC/AV HDMI input terminal
• Use a commercially available HDMI cable (conforming to
the HDMI standard).
• Set HDMI of INPUT SELECT on the OPTION menu
according to the device to be connected.
• Select the audio input terminal to be used in PC HDMI
or AV HDMI of AUDIO SELECT on the OPTION menu.
When HDMI is selected, connection to the audio input
terminal is unnecessary.
2. PC D-sub input terminal
• When the PN-ZB02 (optional) is attached, select the audio
input terminal to be used in PC D-SUB of AUDIO SELECT
on the OPTION menu.
When the PN-ZB02 (optional)
is attached
8
9 10 11 12 13 14 16 17
15
1
2 3 4 5
7
6
Caution
• Be sure to turn off the main power switch and disconnect
the plug from the power outlet before connecting/
disconnecting cables. Also, read the manual of the
equipment to be connected.
• Be careful not to confuse the input terminal with the output
terminal when connecting cables. Accidentally reversing
cables connected to the input and output terminals may
cause malfunctions and the other problems.
TIPS
• Images may not be displayed properly depending on the
computer (video card) to be connected.
• A screen with 1920 x 1080 resolution may not be displayed
correctly on PC RGB. In this case, check the settings of your
computer (video card) to verify that input signals conform to
specifications of this monitor. (See page 57.)
• If there is a check box to disable EDID in display control
panel, check it when using PC RGB.
• Use the automatic screen adjustment when a PC screen
is displayed for the first time using PC D-SUB or PC RGB,
or when the setting of the PC is changed. The screen is
adjusted automatically when SELF ADJUST in the OPTION
menu is set to ON.
• If the audio output from the playback device is connected
directly to speakers or other devices, the video on the monitor
may appear delayed from the audio portion.
Audio should be played through this monitor by connecting the
playback device to the monitor’s audio input, and connecting
the monitor’s audio output to the speakers or other devices.
• The audio input terminals used in each input mode are
factory-set as follows.
Input mode
PC D-SUB, PC DVI-D, PC RGB
AV DVI-D
AV component,
AV S-video, AV video
PC HDMI, AV HDMI
E
12
Audio input terminal
(Factory setting)
Audio input terminal
Audio1 input terminal
Audio2 input terminal
PC/AV HDMI input terminal
3. Audio input terminal
• Use an audio cable without resistance.
• When the PN-ZB02 (optional) is attached, set the audio
input terminal used for each input mode in AUDIO
SELECT on the OPTION menu.
4. Audio output terminals
• The output sound varies depending on the input mode.
• The volume of the output sound can be fixed by setting
AUDIO OUTPUT(RCA) on the OPTION menu.
• It is not possible to control the sound output from the
audio output terminals with the AUDIO menu.
5. RS-232C output terminal
6.RS-232C input terminal
• You can control the monitor from a PC by connecting a
commercially available RS-232 straight cable between
these terminals and the PC.
• When using the PN-ZR01 control kit (optional) to perform
operation of multiple monitors with the remote control
unit, connect multiple monitors in a daisy chain using the
commercially available RS-232 straight cable. (See page 14.)
7.Control kit terminal
• Connects the remote control sensor box of the PN-ZR01
control kit (optional). (See page 14.)
■ Connection when the PN-ZB02 (optional)
is attached
The PN-ZB02 expansion board (optional) allows the use of
additional connection terminals.
8. PC/AV DVI-D input terminal
• Set DVI of INPUT SELECT on the OPTION menu
according to the device to be connected.
• Select the audio input terminal to be used in PC DVI-D or
AV DVI-D of AUDIO SELECT on the OPTION menu.
9. PC/AV DVI-D output terminal
• The video of the PC/AV DVI-D input can be output to an
external device.
• Outputting HDCP-encrypted video requires an external
device which supports HDCP.
• This terminal allows the daisy chain connection of up to 5
monitors.
Connecting Peripheral Equipment
TIPS
• The length of the signal cables or surrounding environment
may affect the image quality.
• The screen may not display properly when using terminals
other than PC DVI-D/AV DVI-D for the input mode. In this
case, turn off the power to all the monitors connected in a
daisy chain and then turn the power on again.
• When connecting monitors in a daisy chain set AUTO
INPUT CHANGE to OFF.
• Video output is disabled in the following cases:
When the power is turned off
When the monitor is in input signal waiting mode
Multiple monitor connection
The monitors can be aligned and used as a large screen.
[Example]
Remote control sensor box
(Supplied with the PN-ZR01 (optional))
10. LAN terminal
• You can control the monitor from a PC on a network by
connecting a commercially available LAN cable between
this terminal and a network.
11. External speaker terminals
• Be sure to use external speakers with an impedance of 6 Ω
or greater and a rated input of at least 10 W.
1
Approx.
3-15/16 inch
(10 cm)
2
3
Second monitor
Secondary
(Expansion unit)
ID No.: 2
First monitor
Primary
(Main unit)
ID No.: 1
Third monitor
Secondary
(Expansion unit)
ID No.: 3
Fourth monitor
Secondary
(Expansion unit)
ID No.: 4
TIPS
• Connect the RS-232C cables in order, starting with the first
monitor (primary monitor). If monitors are connected in a
different order they may not be operable.
• Always install the remote control sensor box on the primary
monitor.
■ Connection with video cable
May vary depending on the system being used.
If using the PC/AV DVI-D terminal, up to 5 monitors can be
connected in a daisy chain. (When the PN-ZB02 is attached)
1. Attach a speaker cable core (included with the PN-ZB02) to
the end of the speaker cable connected to the monitor.
2. While pushing the tab, insert the tip of the cable.
3. Release the tab.
Second monitor
First monitor
TIPS
• Be sure to connect the + and - terminals and the left and
right speakers properly.
• Avoid short circuiting the + and - terminals.
PC/AV DVI-D
input terminal
PC/AV DVI-D
output terminal
PC/AV DVI-D
input terminal
12. Audio1 input terminals
13. Audio2 input terminals
• Set the audio input terminal to be used in each input
mode in AUDIO SELECT on the OPTION menu.
14. PC RGB input terminals
• Set BNC of INPUT SELECT on the OPTION menu to PC
RGB when using the PC RGB input terminals.
• Select the audio input terminal to be used in PC RGB of
AUDIO SELECT on the OPTION menu.
15. AV component input terminals
• Set BNC of INPUT SELECT on the OPTION menu to AV
COMPONENT when using the AV component input terminals.
• Select the audio input terminal to be used in AV
COMPONENT of AUDIO SELECT on the OPTION menu.
16. AV video input terminal
• Select the audio input terminal to be used in AV VIDEO of
AUDIO SELECT on the OPTION menu.
17. AV S-video input terminal
• Select the audio input terminal to be used in AV S-VIDEO
of AUDIO SELECT on the OPTION menu.
Digital signal (DVI) cables
(commercially available)
To PC digital RGB output terminal
shows the
signal flow
13
E
Connecting Peripheral Equipment
■ Connection with RS-232 cable
If you connect the monitor in a daisy chain using RS-232
cable, using the monitor buttons on the primary (main unit),
settings are copied to the secondary (expansion unit) and
operation from the primary can perform operation for all
monitors. Setting each ID No. in the monitor is required.
1. Connect the monitors in order.
The first monitor will be set as primary (main unit) and the
second monitor and beyond will be secondaries (expansion
units).
Connect the RS-232C output terminal of the first monitor
(primary) and the RS-232C input terminal of the second
monitor (secondary) together using RS-232 cable (straight).
Connect in the same way to the third and subsequent monitors.
Up to 25 monitors can be connected. (Depending on the length
of the cable used and the surrounding environment.)
First monitor: primary
Second monitor: secondary
For the monitor in
landscape orientation
For the monitor in
portrait orientation
1. Insert the anti-rotation protrusion of the mounting
bracket into the anti-rotation hole of the monitor.
2. Secure the stand angling hole of the monitor with the
mounting screw.
3. Adjust the angle of the remote control sensor box, and
secure it with the fixing screw, so that it may accurately
receive signals from the remote control unit.
Stand angling hole
Remote control
sensor box
RS-232C
output terminal
RS-232C
input terminal
RS-232C
output terminal
Angle
adjustment
Anti-rotation hole
Fixing screw
Anti-rotation protrusion
Mounting bracket
Mounting screw (short)
RS-232 straight cable
(commercially available)
4. Insert the remote control sensor box connection cable
into the control kit terminal.
Remote control
sensor box
Third monitor: connects to secondary
RS-232C input terminal
2. Set the ID No.
Perform operation with the rear side buttons on the primary
monitor. If you set AUTO ASSIGN ID No., located in the menu
of the monitor to ON, the ID No. will be automatically assigned
in order from the primary. (See page 24.)
(If you attach PN-ZR01 the control kit (optional), you can
perform operation of the monitors with the remote control unit.)
■ Connection with the control kit (optional)
If performing operation of the monitor with the remote control
unit, the PN-ZR01 control kit (optional) is required.
• Can perform operation of an arbitrary monitor or all
monitors with the remote control unit of the first monitor.
• Can perform operation of up to 25 monitors.
• Connect the monitors together in a daisy chain with RS-232
cable.
Attach the remote control sensor box as shown in the following
illustration.
* When attached to the left side, because the top and
bottom for the remote control sensor box will be reversed
(the connection cable will be on top), the right side is
recommended.
Caution
• When attaching the remote control sensor box, turn the
main power switch OFF.
• Except for the remote control sensor box connection cable,
do not insert any other cable into the control kit terminal.
Also, do not connect any connection cables that have been
extended with commercially available cables.
E
14
Control kit terminal
Connection cable
TIPS
• When you connect the remote control sensor box, the
brightness sensor can be used.
The screen brightness will automatically change according
to lighting conditions and the surrounding brightness. (See
page 25.)
• Depending on where it has been placed or the surrounding
conditions, the remote control sensor box may be
affected by the brightness of the main unit screen and the
brightness sensor may respond.
• Do not install the remote control sensor box in extremely
bright or dark areas. The brightness sensor may not
function properly.
Brightness
sensor
Preparing the Remote Control Unit
Installing the batteries
Remote control operation range
1. Press the cover gently and slide it in the direction of the
arrow.
The operation range of the PN-ZR01 (optional) remote control
unit is approx. 23 feet (7 m) when aimed directly at the remote
control sensor box. When used at an angle of approx 10° from
the center to the top/bottom/right/left of the remote control
sensor, use it within a distance of approx 16.4 feet (5 m).
Remote control
sensor
2. See the instructions in the compartment and put in the
batteries (R-6 (“AA” size) x 2) (supplied with the PN-ZR01
(optional)) with their plus (+) and minus (-) sides oriented
correctly.
3. Close the cover.
16.4 feet
(5 m)
23.0 feet
(7 m)
10º
16.4 feet
(5 m)
10º
TIPS
• When the batteries become exhausted replace them with
new (commercially available) batteries.
• The supplied batteries (R-6 (“AA” size) x 2) may become
exhausted quickly depending on how they are stored.
• If you will not be using the remote control for a long time,
remove the batteries.
• Use manganese or alkaline batteries only.
TIPS
• Do not expose the remote control unit to shock by dropping
or stepping on it. This could lead to a malfunction.
• Do not expose the remote control unit to liquids, and do not
place it in an area with high humidity.
• The remote control unit may not work properly if the remote
control sensor is under direct sunlight or strong lighting.
• Objects between the remote control unit and the remote
control sensor may prevent proper operation.
• Replace the batteries when they run low as this may
shorten the remote control’s operation range.
• If a fluorescent light is illuminated near the remote control
unit, it may interfere with proper operation.
• Do not use it with the remote control of other equipment
such as air conditioner, stereo components, etc.
• Adjust the angle of the PN-ZR01 (optional) remote control
sensor and have it face the area where operation with the
remote control unit will take place.
Connecting the Power Cord
Caution
• Use only the power cord supplied with the monitor.
1. Turn off the main power switch.
2. Plug the power cord (supplied) into the AC input terminal.
3. Plug the power cord (supplied) into the AC power outlet.
3
Main power switch
1
For power
outlet
2
AC input terminal
Power cord (Supplied)
15
E
Binding Cables
The cables connected to the terminals on the rear of the monitor can be fastened with the cable clamps.
Insert the cable clamp into the cable clamp attachment on the rear of the monitor and fasten the cables.
Cable
: Cable clamp attachment
Cable clamp
attachment
Cable clamp
Removing the Handles
The handles can be removed.
The removed handles can be attached on the side.
1. Remove the handle screws and remove the handles and
handle spacers.
2. Pass the handle screws through the handles and handle
spacers in order and secure.
Handle spacers
Handle screws
Caution
• The handles, handle screws and handle spacers are for
this monitor. Do not use them for any other devices.
• When attaching the handles, always use this monitor’s
handles, handle spacers, and handle screws.
• Be sure the handles are attached securely.
Handle
Handle spacers
TIPS
• To lower the height of the handles, attach the handles with
the handle spacers removed. To attach the handles with
the handle spacers removed, secure the handles with the
included handle screws (short).
Affixing the Protection Covers
Protection cover
Protection cover
E
16
After installing the monitor, affix the protection covers
(4 pieces) as necessary.
Turning Power On/Off
nOperation mode
Caution
• Turn on the monitor first before turning on the PC or
playback device.
Turning on the main power
Main power switch
Caution
• The main power must be turned on/off with the main power
switch. Do not connect/disconnect the power cord or turn
the breaker on/off while the main power switch is on.
• When switching the main power switch or the POWER
button off and back on, always wait for at least 5 seconds.
• For a complete electrical disconnection, pull out the main
plug.
When the monitor is turned on for the first time after being
shipped from the factory, the operation mode setting screen
will be displayed. Set it to MODE1 or MODE2.
MODE1����OFF IF NO OPERATION is set to ON, and
STANDBY MODE is set to LOW POWER. (These
settings can not be changed.)
If there is no operation for 4 hours or more, the
monitor automatically enters standby mode. Power
consumption in standby mode is also minimized.
MODE2����Will perform standard operation.
OFF IF NO OPERATION is set to OFF, and
STANDBY MODE is set to STANDARD. These
settings can be changed.
Even after being set, changes can be made using
OPERATION MODE, located in the menu of the monitor. (See
page 24.)
nDate/time setting
• If the time has yet to be set when the monitor is first turned on,
the date/time setting screen appears. Set the date and time.
DATE/TIME SETTING
/
Turning power on/off
SET
Press the POWER button on the remote control unit or the
monitor itself to turn the power ON/OFF.
When the main power switch is off, the monitor cannot be
turned on using the POWER button on the remote control unit.
:
/
01
/
01
/ 20
11
:
00
:
00
CANCEL
OK···[MENU]
1. Press
,
,
or
to select the date and
or
to change the numerical
time, and press
values.
or
to select SET and then press MENU .
2. Press
Power LED Power button
Status of a power LED
Status of the monitor
Lit green
Power on
Lit orange
Power off (Standby mode)
Flashing green
Input signal waiting mode
Caution
• When switching the main power switch or the POWER
button off and back on, always wait for at least 5 seconds.
A short interval may result in a malfunction.
TIPS
• If the monitor is in the input signal standby mode and you
press the POWER button on the remote control unit, the
monitor enters standby mode.
• Setting the SCHEDULE flashes the power LED alternately
in red and orange in standby mode.
• To disable the logo screen from displaying when turning
the power ON, set LOGO SCREEN to OFF on the SETUP
menu. (See page 25.)
• If you change the remote control mode to ALL MONITORS,
power can be turned ON/OFF for all secondary monitors
connected with RS-232 cable. (For operation with the
monitor buttons, use the buttons on the primary monitor.)
• Be sure to set the date and time.
• The date/time setting screen will close automatically if no
operation is performed for about 15 seconds. The date
and time can be set using DATE/TIME SETTING from the
OPTION menu when the date/time setting screen disappears.
TIPS
Set the date in “Day/Month/Year” order.
Set the time on a 24-hour basis.
The clock is maintained by the internal battery.
If you already set the time but the date/time setting
screen appears when the power is turned on, the
internal battery may be exhausted. Please contact
your local Sharp servicing dealer or service center for
assistance with battery replacement.
• Estimated service life of the internal battery: About 5
years (depending on monitor operation)
• The initial battery was inserted at the factory when the
monitor was shipped, so it may run out of power before
its expected operation life.
•
•
•
•
Disabling power on/off operations
Power on/power off operations can be disabled in order to protect
the monitor from an accidental power off. Set the ADJUSTMENT
LOCK in FUNCTION menu to “ON 2”. (See page 31.)
17
E
Basic Operation
When performing operation of multiple monitors with the
remote control unit, first set the remote control unit to the
appropriate remote control mode (see page 21).
1. INPUT (Input mode selection)
The menu is displayed. Press
or
mode, and press
to enter.
Input mode
1
2
3
4
5
7
6
8
TIPS
• You can perform operation of the monitor with the rear
buttons. Utilize the buttons belonging to the monitor that
you would like to operate.
• Operation by using the buttons on the rear side of the
product will perform the same functions.
Rear side buttons
Remote control
unit buttons
This manual assumes that this product will be used with
the remote control unit buttons, except where specifically
noted.
to select the input
Video
Audio
PC D-SUB
PC D-sub input terminal
PC HDMI
PC/AV HDMI input terminal*1
AV HDMI
PC/AV HDMI input terminal*1
Audio input terminal
*2
When the PN-ZB02 (optional) is attached
Input mode
Video
Audio
PC DVI-D
PC/AV DVI-D input terminal*3
PC HDMI
PC/AV HDMI input terminal*1
PC D-SUB
PC D-sub input terminal
PC RGB
PC RGB input terminals*4
AV DVI-D
PC/AV DVI-D input terminal*3
AV HDMI
terminal*1
PC/AV HDMI input
*2
AV COMPONENT AV component input terminals*4
AV S-VIDEO
AV S-video input terminal
AV VIDEO
AV video input terminal
*1 Select the terminal to be used in HDMI of INPUT SELECT.
(See page 26.)
*2 Select the terminal for AUDIO SELECT which is used for
audio input. (See page 26.)
*3 Select the terminal to be used in DVI of INPUT SELECT.
(See page 26.)
*4 Select the terminal to be used in BNC of INPUT SELECT.
(See page 26.)
2. MUTE
Turns off the volume temporarily.
Press the MUTE button again to turn the sound back to the
previous level.
If using the monitor buttons, either hold both
and
at the
same time or select MUTE AUDIO from the OPTION menu.
3. MENU
Displays and turns off the menu screen (see page 22).
4. VOL +/- (Volume adjustment)
Pressing
or
displays the VOLUME menu when the
menu screen is not displayed.
VOLUME
15
Press
or
to adjust the volume of the sound.
* If you do not press any buttons for about 4 seconds, the
VOLUME menu automatically disappears.
E
18
Basic Operation
5. BRIGHT +/- (Backlight adjustment)
Pressing
or
displays the BRIGHT menu when the
menu screen is not displayed.
BRIGHT
15
Press
or
to adjust the brightness.
* If you do not press any buttons for about 4 seconds, the
BRIGHT menu automatically disappears.
* When BRIGHTNESS SENSOR is ON or ON: DISPLAY,
when the brightness is adjusted BRIGHTNESS SENSOR
will become OFF.
6. SIZE (Screen size selection)
The menu is displayed.
or
to select the screen size. (See page 20.)
Press
If using the monitor buttons, select SIZE from the OPTION
menu.
7. DISPLAY
Displays monitor information. When you press this button
again, the display disappears.
When the PN-ZB02 (optional) is attached, the display changes
from INFORMATION1 → INFORMATION2 → clear display,
and so on every time you press this button.
• The display disappears automatically after about 15
seconds.
• LAN is displayed during LAN communication.
• If LAN is displayed in red, there is a duplicate IP address.
under INFORMATION in
If using the monitor buttons, press
the OPTION menu.
8. MODE (Color mode selection)
Each time you press this button, the color mode changes in
the following order:
STD (Standard) → VIVID → sRGB →
HIGH ILLUMINANCE → STD...
• HIGH ILLUMINANCE is a display with colors suited to
bright locations.
• sRGB applies to PC input only.
sRGB is international standard of color representation
specified by IEC (International Electrotechnical
Commission). Color conversion is made in taking account
of liquid crystal’s characteristics and represents color tone
close to its original image.
If using the monitor buttons, select COLOR MODE from the
PICTURE menu.
19
E
Basic Operation
nSwitching the screen size
Even when the screen size is changed, the display may remain the same depending on the input signal.
WIDE
ZOOM 1
PC input
Displays image so it fills the entire screen.
AV input
An image with a 4:3 aspect ratio is stretched to fill the entire
screen.
PC input
An image with a 4:3 aspect ratio is enlarged to fill the entire screen
without changing the aspect ratio. The edges of the image may be
cut off.
AV input
ZOOM 2
PC input
Use this size if ZOOM 1 cuts off the subtitles.
AV input
NORMAL
Dot by Dot
PC input
Displays image so it fills the screen without changing the aspect
ratio of the input signals.
AV input
Displays the entire image of the aspect ratio of 4:3 without
changing the aspect ratio.
PC input
Displays the dots of the signals input from the connected PC as
the corresponding dots on the screen.
AV input
Displays the dots of the input signals as the corresponding dots on
the screen.
TIPS
• Using this monitor’s screen-size switching or dual-screen display functions to compress or expand the screen for commercial
or public viewing in establishments like cafes or hotels may infringe on the rights of the creators, as protected by Copyright
Law, so please be careful.
• When “Enlarge” is set, the screen size is fixed to “WIDE” mode.
• When dual-screen display is selected, the screen size cannot be changed.
• The appearance of the original video may change if you select a screen size with a different aspect ratio than the original
image (e.g. TV broadcast or video input from external equipment).
• When an ordinary non-wide image (4:3) is viewed with the whole screen using the screen-size switching function of this
monitor, the edge of the image may be lost or appear distorted. If you wish to respect the creator’s intentions, set the screen
size to “NORMAL”.
• When playing commercial software, parts of the image (like subtitles) may be cropped. In this case select the optimal screen
size using the screen-size switching function of this monitor. With some software, there may be noise or distortion at the
edges of the screen. This is due to the characteristics of the software, and is not a malfunction.
• Depending on the original image size, black bands may remain at the edges of the screen.
E
20
Remote Control Mode
With the remote control unit it’s possible to perform operation
of...
• The primary monitor
• Monitors with a specified ID No.
• All primary/secondary monitors
It’s necessary to specify which type of operation will be
performed in advance.
MODE
1. If using the remote control unit, press
seconds.
If using the monitor buttons, hold both
the same time on the primary.
for approx 5
and
at
ALL MONITORS
Performs operation of all primary/secondary monitors.
* ALL will be displayed on the menu of the primary.
* When it receives signals from the remote control unit,
“Operating all monitors.” will be displayed on the secondary
screen. (Excluding power and input mode selection operation)
* Settings may not be reflected depending on the state of the
connected monitors.
[Example] If the power for the primary is turned ON, the power
for all the monitors will be turned ON.
REMOTE CONTROL MODE
▲
THIS MONITOR ONLY
▲
MODE
Operate this monitor.
OK
or
2. Press
settings.
CANCEL
, select the mode, then perform
Secondary
ID No.: 2
Primary
ID No.: 1
VOLUME 10
Secondary
ID No.: 3
Secondary
ID No.: 4
to lower the volume
SPECIFIED MONITOR
Performs operation of a monitor with a specified ID No. using
the remote control unit.
or
to select ID No., then press
or
to
Press
select the ID No. of the monitor that you will operate.
* When it receives signals from the remote control unit,
“Operating specified monitor.” will be displayed on the
primary screen.
[Example.] If ID No. is set to 3 and the volume is lowered,
the volume of the monitor for ID No.: 3 will lower.
Secondary
ID No.: 2
Primary
ID No.: 1
Secondary
ID No.: 4
VOLUME 10
Press
Secondary
ID No.: 3
Power ON
Secondary
ID No.: 4
Power ON
to lower the volume
When you would like to confirm the ID No. that is set to the
monitor, press
or
to select ID No. DISPLAY, then
press
. The ID No. will be displayed on the screen.
POWER
to turn the power ON
Press
or
to select EXPAND ITEM, and press
or
to select to perform this action or not.
OFF�����������For all monitors, only power, input mode
selection, and product information display
operations will be recognized.
ON�������������For all monitors, all operations will be
recognized.
After returning to the normal screen with
procedure 3, when 5 minutes have passed from
the end of operation, it will automatically return
to OFF.
ALL [EXPAND ITEM]
will be displayed on the menu of
the primary.
* Even when REMOTE CONTROL MODE is set
to ALL MONITORS, certain settings such as
LAN settings and ID No. settings will not be
reflected on the other monitors.
3. Press
or
to select OK, then press
return to the normal screen.
MENU
and
4. Perform operation.
Caution
• When the remote control mode is set to ALL MONITORS
and EXPAND ITEM is set to ON, performing remote control
operations that change adjustment values will result in
the secondary adjustment values being the same as the
primary adjustment values.
Secondary
ID No.: 2
VOLUME 12
Primary
ID No.: 1
VOLUME 11
Secondary
ID No.: 2
VOLUME 10
Primary
ID No.: 1
VOLUME 10
Secondary
ID No.: 3
VOLUME 9
Secondary
ID No.: 4
VOLUME 10
Secondary
ID No.: 3
VOLUME 10
Secondary
ID No.: 4
VOLUME 10
Press
Secondary
ID No.: 3
Primary
ID No.: 1
Power ON
Press
THIS MONITOR ONLY
Performs operation of only the primary using the remote
control unit.
[Example] If the volume is lowered, the volume of the primary
will lower.
Press
Secondary
ID No.: 2
Power ON
to lower the volume
Be careful of this when adjusting individual displays.
TIPS
• You can copy the setting values of the primary to other
monitors with COPY SETTING VALUE. (See page 25.)
• The buttons on the monitor itself (primary) are also effective
in remote control mode.
• When monitors connected in a daisy chain are in standby
mode for LOW POWER, operation cannot be performed for
subsequent monitors.
21
E
Menu Items
Displaying the menu screen
TIPS
Video and audio adjustment and settings of various functions
are enabled. This section describes how to use the menu
items. See pages 23 to 27 for details of each menu items.
Caution
• Do not turn the main power switch off while the menu items
are being displayed. Doing so may initialize the settings.
nExample of operation
MENU
SCREEN
1/1
AUTO
CLOCK
PHASE
H-POS
V-POS
H-SIZE
V-SIZE
H-RESOLUTION
V-RESOLUTION
RESET
PICTURE
AUDIO
SETUP
OPTION
MULTI
PIP/PbyP
1366x768
SETUP
PC D-SUB
MULTI
V: 60 Hz
PIP/PbyP
H: 47.7 kHz
END···[MENU]
3. Press
or
to select CONTRAST.
PICTURE
SETUP
OPTION
MULTI
PIP/PbyP
64
86
31
30
30
30
30
12
MOVE OSD···[DISPLAY]
1366x768
V: 60 Hz
4. Press
or
SCREEN
AUDIO
SETUP
OPTION
MULTI
PIP/PbyP
MOVE OSD···[DISPLAY]
1366x768
V: 60 Hz
For items that have
MENU
press
.
5. Press
22
MENU
, press
FULL
H: 47.7 kHz
OK···[MENU]
4
1 Name of the menu
2 Input mode
3 An item being selected (highlighted)
4 Screen resolution of input signal, and other data.
• Items that cannot be selected appear in gray.
(e.g. Function not supported by the current input signal)
The displayed menu items vary depending on whether or not
the PN-ZB02 (optional) is attached.
The following menus will be displayed only when the PN-ZB02
(optional) is attached.
FULL
OK···[MENU]
H: 47.7 kHz
PC D-SUB
64
86
31
40
30
30
30
12
64
86
31
30
30
30
30
12
nMenu Items
1/2
AUTO
ANALOG GAIN
ANALOG OFFSET
BRIGHT
CONTRAST
BLACK LEVEL
TINT
COLORS
SHARPNESS
RGB INPUT RANGE
PICTURE
PC D-SUB
1/2
AUTO
ANALOG GAIN
ANALOG OFFSET
BRIGHT
CONTRAST
BLACK LEVEL
TINT
COLORS
SHARPNESS
RGB INPUT RANGE
TIPS
to adjust the setting.
PICTURE
PICTURE
2
.
PC D-SUB
1/2
AUTO
ANALOG GAIN
ANALOG OFFSET
BRIGHT
CONTRAST
BLACK LEVEL
TINT
COLORS
SHARPNESS
RGB INPUT RANGE
3
MOVE OSD···[DISPLAY]
1366x768
V: 60 Hz
to select PICTURE, and press
AUDIO
OPTION
600
25
610
37
50
50
1366
768
or
PICTURE
E
AUDIO
2. Press
SCREEN
1
SCREEN
to display the menu screen.
SCREEN
nMenu screen display
PICTURE
(Adjusting CONTRAST in the PICTURE menu)
1. Press
• The menu will differ depending on the input mode.
• The menu screen will close automatically if no operation is
performed for about 15 seconds. (DATE/TIME SETTING,
SCHEDULE and LAN SETUP screens will close in about 4
minutes.)
FULL
H: 47.7 kHz
OK···[MENU]
, make settings and then
twice to close the menu screen.
Menu
Item
PICTURE ADVANCED
3D-Y/C
SETUP
HOT PLUG CONTROL DVI
RS-232C/LAN SELECT
LAN SETUP
AUTO ASSIGN FIXED IP ADDR.
OPTION
INPUT SELECT
DVI
BNC
AUDIO SELECT
PC DVI-D
PC D-SUB
PC RGB
AV DVI-D
AV COMPONENT
AV S-VIDEO
AV VIDEO
COLOR SYSTEM
PIP/PbyP PIP SOURCE
Menu Items
Menu item details
The menu will differ depending on the input mode.
nSCREEN
You can move the menu screen display position each time
DISPLAY
is pressed.
AUTO (PC D-SUB/PC RGB)
The CLOCK, PHASE, H-POS, and V-POS are automatically
adjusted.
Pressing
performs adjustment.
Use this automatic adjustment when you use the PC D-sub
input terminal or PC RGB input terminals to display a PC
screen for the first time or when you change the setting of
the PC. (See page 30.)
CLOCK (PC D-SUB/PC RGB)
Adjusts frequency for sampling clock for applicable video.
Adjust when there is flickering in the form of vertical stripes.
When using the adjustment pattern (see page 30), make
adjustments so that no vertical stripe noise appears in it.
PHASE (PC D-SUB/PC RGB)
Adjusts sampling clock phase for applicable video.
Useful when small characters appear with low contrast and/
or there are flickers at corners.
When using the adjustment pattern (see page 30), make
adjustments so that no horizontal stripe noise appears in it.
* Adjustments to PHASE should be made only after CLOCK
has been correctly set.
H-POS
Adjust the horizontal position of the image.
V-POS
Adjust the vertical position of the image.
H-SIZE
Adjust the horizontal size of the image.
V-SIZE
Adjust the vertical size of the image.
H-RESOLUTION (PC D-SUB/PC RGB)
Sets proper horizontal resolution when the resolution of
input signals is not recognized properly. (Adjustment may be
impossible with some signals.)
V-RESOLUTION (PC D-SUB/PC RGB)
Sets proper vertical resolution when the resolution of input
signals is not recognized properly. (Adjustment may be
impossible with some signals.)
RESET
Resets the values of the SCREEN menu items to the factory
preset values.
MENU
Select “ON” and then press
.
nPICTURE
You can move the menu screen display position each time
DISPLAY
is pressed.
AUTO (PC D-SUB/PC RGB)
The ANALOG GAIN and ANALOG OFFSET are
automatically adjusted.
performs adjustment.
Pressing
ANALOG GAIN (PC D-SUB/PC RGB)
Adjusts the bright portions of the video input signal.
ANALOG OFFSET (PC D-SUB/PC RGB)
Adjusts the dark portions of the video input signal.
BRIGHT
Adjusts the backlight brightness. (In PIP mode, the main side
setting is reflected in the image.)
CONTRAST
Adjusts the difference between the bright and dark portions
of the image.
BLACK LEVEL
Adjusts the entire brightness of the video signals.
TINT
Adjusts the hue. Selecting + changes the color towards
green, and selecting - changes it towards magenta.
COLORS
Adjusts the color intensity.
SHARPNESS
Adjusts the sharpness of the image.
RGB INPUT RANGE (PC DVI-D/PC HDMI/PC D-SUB/PC
RGB/AV DVI-D/AV HDMI)
Sets the RGB input signal range. When using HDMI set to
AUTO, the RGB input signal is detected automatically. Use
AUTO normally.
If the RGB input signal range cannot be set appropriately
even when using AUTO, set according to the image. When
the setting is different, images will be displayed with washed
out blacks and compressed gradients.
ADVANCED (AV input)
You can adjust more specifically. (See page 30.)
COLOR MODE
Changes the color mode on the screen. The color mode on
the screen can also be changed using a remote control unit.
(See page 19.)
* sRGB is for PC input only. See page 19 for details.
WHITE BALANCE
THRU�������������� Displays the input signal level as is. (for PC
DVI-D/PC HDMI only)
PRESET��������� Selects the color temperature using PRESET.
USER�������������� Used for adjusting R-/G-/B-CONTRAST and
R-/G-/B-OFFSET respectively.
PRESET
Selects the color temperature when the WHITE BALANCE is
set to PRESET.
The setting values are shown for reference. The color
temperature of the screen varies over time.
This function is not intended to keep the color temperature
constant.
23
E
Menu Items
USER
Adjusts each item when the WHITE BALANCE is set to
USER.
R-CONTRAST.....Adjusts bright-toned red component.
G-CONTRAST.....Adjusts bright-toned green component.
B-CONTRAST.....Adjusts bright-toned blue component.
R-OFFSET...........Adjusts dark-toned red component.
G-OFFSET..........Adjusts dark-toned green component.
B-OFFSET...........Adjusts dark-toned blue component.
COPY TO USER
Copies the value set for PRESET to the USER setting.
MENU
Select “ON” and then press
.
GAMMA
Selects the gamma. USER sets the gamma to the sent
value (see page 36). (In PIP mode, the main side setting is
reflected in the image.)
DISPLAY COLOR PATTERN
Displays a color pattern. Can be displayed while the menu
screen is displayed, so you can refer to the pattern while
adjusting the image.
OFF.....................No pattern display.
WHITE.................White single color pattern display.
RED.....................Red single color pattern display.
GREEN................Green single color pattern display.
BLUE...................Blue single color pattern display.
USER..................Red/green/blue mixed color pattern display.
When USER is selected, set each color’s
level.
RESET
Resets the values of the PICTURE menu items to the factory
preset values.
MENU
Select “ON” and then press
.
nAUDIO
TREBLE
Adjusts the volume of treble-level sound.
BASS
Adjusts the volume of bass-level sound.
BALANCE
Adjusts the balance of the audio sound between right and
left.
RESET
Resets the values of the AUDIO menu items to the factory
preset values.
MENU
.
Select “ON” and then press
nSETUP
OSD H-POSITION
Adjusts the horizontal display position of menu screen.
OSD V-POSITION
Adjusts the vertical display position of menu screen.
MONITOR
Select the installation direction of the monitor.
LANDSCAPE.............Horizontal orientation
PORTRAIT................Vertical orientation
LANGUAGE
Sets the display language for the menu screen.
E
24
POWER ON DELAY
You can delay the screen display after the monitor is turned
on. The period can be set up to 60 seconds in units of one
second. When this function is activated, the power LED
flashes (at approx. 1 second interval) in orange. This function
is disabled when 0 is specified.
OPERATION MODE
MODE1������OFF IF NO OPERATION is set to ON, and
STANDBY MODE is set to LOW POWER.
(These settings can not be changed.)
MODE2������Will perform standard operation.
OFF IF NO OPERATION is set to OFF, and
STANDBY MODE is set to STANDARD. These
settings can be changed.
STANDBY MODE
When STANDARD is selected, startup time from standby
mode is reduced. Note, however that, more power will be
consumed in standby mode.
When LOW POWER is selected, current consumption
is reduced while the monitor is in standby mode. Note,
however, that the startup time from standby mode becomes
longer.
If set to LOW POWER, certain RS-232C commands cannot
be used in standby mode, and control via LAN will be
disabled.
OFF IF NO OPERATION
Determines whether or not to set the monitor to go into
standby mode when there is no operation from the remote
control unit, RS-232C commands, or LAN for over 4 hours.
HOT PLUG CONTROL
Sets whether to use hot plug control for the PC/AV HDMI
and PC/AV DVI-D input terminals.
RS-232C/LAN SELECT
Selects the method with which to control the monitor from
the computer.
ID No. SET
Assigns ID numbers to monitors connected in a daisy chain
(see page 34), using the remote control unit or RS-232
cables.
The numbers 1 to 255 are available for ID numbers.
If “0” is set, the system regards this as the state where no ID
number is set.
AUTO ASSIGN ID No.
ID No. to be used will be automatically assigned when
multiple monitors are connected with RS-232C.
MENU
Select ON, then press
. Perform operations with the
primary monitor.
Menu Items
BAUD RATE
Selects the communication speed used for RS-232C
communication.
LAN SETUP
Configures the settings to control the monitor from the
computer via LAN. (See page 45.)
AUTO ASSIGN FIXED IP ADDR.
Can be enabled when RS-232C/LAN SELECT is LAN and
the DHCP CLIENT is OFF.
Set the DHCP CLIENT for secondary monitors connected
by RS-232C to OFF and a fixed IP address is automatically
allocated.
If the IP address is a duplicate with a network device other
than a monitor, individually change the IP address.
HDMI AUTO VIEW
When ON is selected, the screen size is adjusted
automatically according to the screen size control signal
included in the video signal input from the AV HDMI input
terminal.
BRIGHTNESS SENSOR
(When connected to the PN-ZR01 (optional) only)
When set to ON or ON: DISPLAY, the brightness will
automatically change according to the lighting and
surrounding brightness. Performs operation with the primary
monitor. If set to ON: DISPLAY, the effect will be displayed
with a
.
If connecting to multiple monitors, the brightness of all the
monitors will change.
The
will be displayed on the primary only.
When setting BRIGHT in SCHEDULE on the OPTION menu,
set BRIGHTNESS SENSOR to OFF.
BRIGHTNESS SENSOR SETTING
(When connected to the PN-ZR01 (optional) only)
Performs adjustments to the brightness sensor. Performs
operation with the primary monitor.
Set the surrounding brightness and the current screen
luminance to AMBIENT BRIGHTNESS and SCREEN
BRIGHTNESS.
Individually set WHEN LIGHT: and WHEN DARK:.
Even if brighter or darker than the set AMBIENT
BRIGHTNESS, the screen brightness will not change.
CURRENT AMBIENT BRIGHTNESS is shown for reference.
COPY SETTING VALUE
When the monitor has been connected to multiple monitors
with RS-232C, you can copy the primary setting details to
the secondary. Perform operations with the primary monitor.
Selects the settings to copy with COPY SETTING VALUE
TARGET.
“PICTURE” ONLY.... Copies the PICTURE menu settings.*
ALL......................... Copies all the settings.*
Select the ID No. of the monitor that you would like copy to
MENU
with COPY TO ID No., then select COPY and press
.
If you select ALL, settings will be copied to all monitors.
When you would like to confirm the ID No. that is set to the
monitor, select ID No. DISPLAY and press
. The ID No.
will be displayed on the screen.
* Certain setting details such as ANALOG GAIN, ANALOG
OFFSET, and DISPLAY COLOR PATTERN cannot be
copied.
LOGO SCREEN
Sets whether or not to display the logo screen.
25
E
Menu Items
nOPTION
DATE/TIME SETTING
Set the date and time. Press
to select the date
or
or
to change the numerical
and time, and press
values.
Set the date in “Day/Month/Year” order.
Set the time on a 24-hour basis. (Factory default)
DATE/TIME FORMAT
Sets the date/time display format.
DATE...................MM/DD/YYYY
DD/MM/YYYY
YYYY/MM/DD
(YYYY: Year, MM: Month, DD: Day)
TIME....................Select 12- or 24-hour time.
SCHEDULE (See page 29.)
You can turn the power on/off and change the screen
brightness at a specified time.
INPUT SELECT
Select the input mode to be used in PC/AV DVI-D input
terminal, PC/AV HDMI input terminal and PC RGB/AV
component input terminals.
AUDIO SELECT
Selects the terminal used to input audio signals in each input
mode.
INPUT SIGNAL (PC D-SUB/PC RGB)
If a computer connected to the PC D-sub/PC RGB input
terminal outputs any of the following resolutions, make a
selection from the following options.
480 LINES...........AUTO, 640x480 or 848x480
768 LINES...........AUTO, 1024x768, 1280x768, 1360x768 or
1366x768
1050 LINES.........1400x1050 or 1680x1050
ZOOM2 SPECIAL SETTING (See page 29.)
SCAN MODE (AV input)
Sets the scan mode used for AV mode input.
MODE1................Over-scan display
MODE2................Under-scan display
MODE3................Under-scan display when the input signal
is 1080i/p. Otherwise, over-scan display
POWER MANAGEMENT
POWER MANAGEMENT determines whether or not to
switch modes from no signal to the input signal standby
mode.
COLOR SYSTEM (AV S-VIDEO/AV VIDEO)
Select the color system of the AV equipment which is
connected to AV S-video and AV video input terminal. (AUTO /
PAL / PAL-60 / SECAM / NTSC3.58 / NTSC4.43)
When AUTO is selected, the color system is automatically set
according to the input signal.
AUDIO OUTPUT(RCA)
Sets the volume of sound output from the audio output
terminals. When set to VARIABLE2, audio is not output from
the external speaker terminals.
VARIABLE...........You can adjust the volume using VOLUME.
FIXED..................Disables volume adjustment and fixes the
sounds.
When the PN-ZB02 (optional) is attached:
VARIABLE1.........You can adjust the volume using VOLUME.
VARIABLE2.........You can adjust the volume using VOLUME,
but audio is not output from the external
speaker terminals.
FIXED..................Disables volume adjustment and fixes the
sounds.
AUDIO LEVEL(STEREO MINI)
Selects the maximum audio input level of the audio input
terminal.
SELF ADJUST
On a PC D-SUB/PC RGB screen, specify whether to
perform screen adjustment automatically or not. When ON
is selected, the screen is automatically adjusted when its
resolution is 800 x 600 or higher and the timing of input
signals changes. “ADJUSTING” appears on the screen
during the adjustment. For images with black edges, etc.,
depending on the signal, adjustment may not be possible.
In this case select OFF. (Perform manual adjustment of the
screen.)
AUTO INPUT CHANGE
Specify whether to change inputs automatically. When ON is
selected and no signal is present in the selected input mode,
AUTO INPUT CHANGE automatically changes the selected
mode to another mode where a video signal is present.
When video signals exist in multiple input modes, the
switching priority is as follows:
PC D-SUB, PC HDMI and AV HDMI
When the PN-ZB02 (optional) is attached:
PC DVI-D, PC HDMI, PC D-SUB, PC RGB, AV DVI-D, AV
HDMI, AV COMPONENT, AV S-VIDEO and AV VIDEO
(Input mode switching may take 15 seconds or more,
depending on the connected equipment. Input signals
may not be detected properly and a priority may change,
depending on the connected equipment or video signals.)
FAN SPEED
Sets the rotation speed of the fan.
As this number increases, the rotation speed becomes
faster. When set to AUTO, the rotation speed of the fan will
change depending on the internal temperature.
SIZE
Selects screen size. (See page 20.)
MUTE AUDIO
Can temporarily turn off the volume.
INFORMATION
If you press
E
26
, monitor information can be checked.
Menu Items
nMULTI
ENLARGE (See page 28.)
Sets whether or not to use the enlarge function.
ADVANCED (ENLARGE)
ENLARGE H / ENLARGE V
.......... Sets the number of screen splits (number of
monitors) in the horizontal/vertical direction used for
the enlargement.
ENLARGE-POS
.......... Specify the split screen to be displayed when the
enlargement function is used.
H-POS / V-POS
.......... Adjust the horizontal/vertical position of the enlarged
screen.
BEZEL ADJUST
Sets whether or not to use the frame correction function.
ADVANCED (BEZEL ADJUST)
BEZEL ADJUST (TOP) / BEZEL ADJUST (BOTTOM) /
BEZEL ADJUST (RIGHT) / BEZEL ADJUST (LEFT)
.......... Adjusts so that the top/bottom/left/right connecting
joints of grouped units will be displayed smoothly
when a group of monitors are aligned in multiples to
display a single image.
BEZEL (TOP) / BEZEL (BOTTOM) / BEZEL (RIGHT) /
BEZEL (LEFT)
.......... Sets the frame width of the display.
nPIP/PbyP
PIP MODES
Sets the display method.
OFF���������Displays one screen.
PIP�����������Displays a sub screen inside a main screen.
PbyP��������Displays a main screen and a sub screen in a line.
PbyP2������Displays a main screen which measures 1024 pixels
in the longest direction and a sub screen in a line.
PIP SIZE
Sets the size of the sub screen in PIP mode.
PIP H-POS
Adjusts the horizontal position of the sub screen in PIP
mode.
PIP V-POS
Adjusts the vertical position of the sub screen in PIP mode.
PIP BLEND
In PIP mode, use this menu item to display the sub screen
transparently.
PIP SOURCE
Selects the input signal of the sub screen in PIP, PbyP, or
PbyP2 mode.
SOUND CHANGE
Sets the sound which is output in PIP, PbyP, or PbyP2 mode.
If the main screen is displayed as a full screen by the AUTO
OFF function, the sound for the main screen is output even
when the sound for the sub screen is specified.
MAIN POS
Sets the position of the main screen in PbyP or PbyP2 mode.
PbyP2 POS
Sets the position of the sub screen in PbyP2 mode.
AUTO OFF
Sets the display method when no signals for the sub screen
are input in PIP, PbyP, or PbyP2 mode.
MANUAL........ Displays a main screen and a black sub screen.
AUTO............. Displays the main screen as a full screen.
TIPS
• When WHITE BALANCE is set to THRU, BLACK LEVEL,
CONTRAST, TINT, COLORS, RGB INPUT RANGE,
GAMMA and COPY TO USER cannot be set.
• If COLOR MODE is set to sRGB, the following items cannot
be set.
WHITE BALANCE, PRESET, USER, COPY TO USER, and
GAMMA
• When the COLOR MODE is set to VIVID or HIGH
ILLUMINANCE, GAMMA can not be adjusted.
• STANDBY MODE cannot be set to LOW POWER when
SCHEDULE is effective or when OFF is selected for LED in
FUNCTION.
• When displaying the color pattern, it is possible to adjust
certain items of the PICTURE menu.
Non-adjustable items cannot be selected.
Audio input from the HDMI input terminal is also not output.
27
E
Menu Items
nDual screen display
nEnlarge
You can display the screens of the PC input signal and AV
input signal simultaneously.
Set this function with “PIP MODES” in the PIP/PbyP menu.
PIP
A sub screen is displayed
inside a main screen.
Main screen
Sub
screen
PbyP
Main
screen
Sub
screen
PbyP2
Main screen
Sub
screen
Displays a main screen
which measures 1024
pixels in the longest
direction and a sub
screen in a line.
TIPS
• You might infringe on a copyright of the author which is
protected by copyright law when you display the images of
the computer screen and television/VCR simultaneously for
profit-making or to show the image to the public.
• The screen size for dual-screen display is the same as
the screen size for single-screen display. The Dot by Dot
screen is displayed in NORMAL size except when it is set
as the PIP main screen.
• When dual-screen display is selected, the AUTO INPUT
CHANGE function is disabled.
• When dual-screen display is selected, the screen cannot
be enlarged.
• When dual-screen display is selected, the INPUT SELECT
options cannot be set.
• When an interlaced signal (1080i, 480i, video, S-Video) is
input to the sub screen, horizontal lines may flicker. If this
happens, display the image on the main screen.
28
(Example)
Horizontal direction: 2 monitors
Vertical direction: 2 monitors
A main screen and a sub
screen are displayed in a
line.
* The currently selected input signal is displayed on the main
screen.
* You cannot simultaneously display the screens of signals
of the same type, such as two types of PC input signals or
two types of AV input signals.
* The dual screen display cannot be used with the
combination of PC DVI-D and AV HDMI or of AV DVI-D and
PC HDMI.
E
• You can align several monitors and integrate them into a
single large screen to display.
• Up to five monitors can be aligned in both the horizontal
and vertical directions.
• Each monitor displays enlarged views of separated images.
Horizontal direction: 3 monitors
Vertical direction: 2 monitors
Setting procedure
Set using the MULTI menu.
1. Set ENLARGE to ON.
2. Select ADVANCED (ENLARGE).
3. Set the number of monitors aligned in the horizontal
direction in ENLARGE H.
4. Set the number of monitors aligned in the vertical
direction in ENLARGE V.
5. Set the section of the separated image to be displayed
on each monitor in ENLARGE-POS.
1) Press
.
2) P
ress
,
,
or
to select position, then
MENU
press
.
TIPS
• When Enlarge is used, the AUTO INPUT CHANGE function
is disabled.
• When Enlarge is used, the HDMI AUTO VIEW function is
disabled.
Menu Items
nZOOM2 SPECIAL SETTING
If you connect a laptop computer with any of the following
screen resolutions and black bands appear around the
screen, set ZOOM2 SPECIAL SETTING of INPUT SIGNAL on
the OPTION menu to ON and then select ZOOM2 in the SIZE
setting.
This displays the area inside the black band.
Laptop computer
resolution
Corresponding signal*1
1280x800
1280x1024, 1280x960, 1400x1050*2
1280x600
1280x720
1024x600
1024x768
*1: This setting is effective only when the screen resolution,
including the black band, is one of the resolutions listed
above.
*2: Use the automatic screen adjustment.
nSCHEDULE
You can set the time to switch the monitor on and off.
Set this function with “SCHEDULE” in the OPTION menu. (See
page 26.)
When BRIGHT is set, set BRIGHTNESS SENSOR to OFF on
the SETUP menu.
PC D-SUB
SCHEDULE
(2)
No. (1) POWER
–
–
–
–
–
–
–
–
––
––
––
––
––
––
––
––
– –/– –/– – – –
(3)
–––
– –:– –:– –
(4)
DAY OF THE WEEK
–
–– - ––
TIME
–– :
–
–
–
–
–
–
–
––
––
––
––
––
––
––
1366x768
––
––
––
––
––
––
––
-
––
––
––
––
––
––
––
V: 60 Hz
:
:
:
:
:
:
:
––
––
––
––
––
––
––
––
(5)
INPUT
––
––
––
––
––
––
––
––
H: 47.7 kHz
(6)
BRIGHT
––
––
––
––
––
––
––
––
Caution
OK···[MENU]
1. Press
or
to select the SCHEDULE number, and
press
.
2. Set the SCHEDULE. (See the description below.)
or
to select items, and press
Press
change the setting.
(3) DAY OF THE WEEK
Specifies the day of the week to execute the SCHEDULE.
0: ONLY ONCE
Executes the SCHEDULE once on the specified day.
Specify the day of the week to execute the SCHEDULE.
1: EVERY WEEK
Executes the SCHEDULE on the specified day of the week
every week. Specify the day of the week to execute the
SCHEDULE.
Periodic setting such as “Monday through Friday” is also
possible.
2: EVERY DAY
Executes the SCHEDULE every day regardless of the day
of the week.
(4) TIME
Specifies the time to execute the SCHEDULE.
Set the time on a 24-hour basis. (Factory default)
Can be entered as 12-hour time using the TIME setting in
DATE/TIME FORMAT.
(5) INPUT
Specifies the input mode at power-on. When not specifying,
the screen at the previous power-off appears.
Input modes displayed on DVI, HDMI and BNC depend on
INPUT SELECT settings.
(6) BRIGHT
Sets the brightness when changing the screen brightness at
a specified time.
or
to
MENU
.
3. Press
SCHEDULE becomes effective.
• Do not switch off the main power after setting the
SCHEDULE.
• Specify the correct date and time. (See page 26.)
SCHEDULE does not function unless the date and time are
specified.
• Check regularly that the set date and time are correct.
• When STANDBY MODE is LOW POWER, SCHEDULE
cannot be set.
• When a temperature abnormality occurs and the backlight
brightness is reduced, the brightness is not changed even
if a schedule set to BRIGHT is executed.
TIPS
• Up to 8 SCHEDULE items can be registered.
• Setting the SCHEDULE flashes the power LED alternately
in red and orange in standby mode.
• A SCHEDULE that has a large number has precedence
over that of a small number when schedules overlap.
(1)
●: SCHEDULE effective
-: SCHEDULE not effective
(2) POWER
ON : Switches the monitor on at the specified time.
OFF: Switches the monitor off at the specified time and puts
the monitor in standby mode.
29
E
Menu Items
nADVANCED items (AV input) (See page 23
for additional Menu item details.)
FLESH TONE
Adjust the hue control.
3D-NR
Reduce the noise of playback images on video.
Setting a higher level reduces more noise. However, it may
cause blurring on an image.
MPEG-NR
Reduce block noise caused by digital compression.
3D-Y/C (AV VIDEO)
Specify whether to perform 3-dimension Y/C separation.
If dot interference or cross-color is occurring in fast-motion
scenes, selecting “OFF” may improve the image quality.
C.M.S.-HUE
Adjusts color tone with 6 colors of R (red), Y (yellow), G
(green), C (cyan), B (blue), and M (magenta).
C.M.S.-SATURATION
Adjusts color vividness with 6 colors of R (red), Y (yellow), G
(green), C (cyan), B (blue), and M (magenta).
C.M.S.-VALUE
Adjusts color brightness with 6 colors of R (red), Y (yellow),
G (green), C (cyan), B (blue), and M (magenta).
TIPS
• When FLESH TONE is set to LOW or HIGH, C.M.S.-HUE/
-SATURATION/-VALUE cannot be set.
Adjustments for PC screen display
nAutomatic adjustment
When you use the PC D-sub input terminal or PC RGB input
terminals to display a PC screen for the first time, or when
you change the setting of the PC, use the automatic screen
adjustment.
1. Switch the input to PC D-SUB or to PC RGB and display
the adjustment pattern. (See the description below.)
MENU
2. Press
and use
or
to display the SCREEN
menu.
3. Press
and select “AUTO”.
.
4. Press
The automatic adjustment is complete in several seconds.
5. Press MENU twice to close the menu screen.
TIPS
• If the screen cannot be adjusted properly with one
automatic adjustment, repeat the automatic adjustment two
or three times. Try manual adjustment if necessary.
nScreen display for adjustment
Before making adjustments in the SCREEN menu or
PICTURE menu, display an image to brighten the entire
screen. If you are using a Windows PC, use the adjustment
pattern on the supplied CD-ROM.
Opening the adjustment pattern
The following example is performed in Windows 7.
1. Load the supplied CD-ROM into the computer’s CDROM drive.
2. Open [CD Drive] in [Computer].
In Windows XP, open [CD Drive] in [My Computer].
3. Double-click [Adj_uty.exe].
The adjustment pattern will appear.
Adjust the screen automatically or manually.
4. When adjustment is finished, press the [Esc] on the
computer’s keyboard to quit the adjustment program.
5. Eject the CD-ROM from the CD-ROM drive.
TIPS
• If the display mode on the computer you are using is
65,000 colors, the color levels in the color pattern may
appear differently or grayscale may appear to be colored.
(This is due to the specifications of the input signal and is
not a malfunction.)
E
30
Initialization (Reset)/Functional Restriction Setting (FUNCTION)
You can return the settings to their factory-preset values and
restrict operations.
SIZE
until “F”
1. If using the remote control unit, press
is displayed in the upper left area of the screen, then
,
,
, and
while “F” is being displayed, press
in that order.
and
at the
If using the monitor buttons, press
same time until “F” is displayed in the upper left area
of the screen, then while “F” is being displayed, press
and
at the same time.
FUNCTION
ALL RESET
ADJUSTMENT LOCK
ADJUSTMENT LOCK TARGET
RS-232C
OSD DISPLAY
LED
TEMPERATURE ALERT
STATUS ALERT
POWER BUTTON
CONTROLLER INPUT
1/1
OFF
UNLOCKED
ON1
ON
LED
OFF
MONITOR
END…[MENU]
2. Select and set the items.
ALL RESET
Resets the settings to the factory default settings.
MENU
, select ALL RESET, and then press
.
Press
After initialization, turn the main power switch off and
then back on.
When the PN-ZB02 (optional) is attached, press
,
MENU
.
select the resetting method, and then press
ALL RESET1����Resets all the settings to the factory
default settings.
ALL RESET2����Returns all settings to the factory default
settings except for the following items:
LAN SETUP, RS-232C/LAN SELECT,
ID No. SET, BAUD RATE, NETWORK,
MAIL, SERVICE & SUPPORT, and
SNMP (See pages 24, 25, and pages 49
to 52.)
ADJUSTMENT LOCK
You can disable operations on the monitor and the
remote control unit that use buttons.
OFF���Enables operation.
ON 1��Disables all operations other than turning power
on/off, FUNCTION and REMOTE CONTROL
MODE.
ON 2��Only the FUNCTION and REMOTE CONTROL
MODE operations are enabled.
Disables all operations other than FUNCTION
and REMOTE CONTROL MODE (not even power
on/off).
ADJUSTMENT LOCK TARGET
Sets the target to prohibit operation of with
ADJUSTMENT LOCK.
REMOTE CONTROL....Prohibits remote control operation
MONITOR BUTTONS.....Prohibits monitor button operation
BOTH.........................Prohibits remote control and
monitor button operation
RS-232C
(RS-232C/LAN when the PN-ZB02 (optional) is
attached)
Specifies whether to allow control via RS-232C or LAN
(see pages 32 and 45).
OSD DISPLAY
Shows/hides the menu, modes, and messages.
The FUNCTION and REMOTE CONTROL MODE
screens cannot be hidden.
ON 1.............. Shows all menus, modes, and messages.
ON 2.............. Hides messages automatically displayed
by the display. Shows messages during
operation.
OFF............... Hides all menus, modes and messages.
LED
Specifies whether to light the power LED.
OFF cannot be selected when STANDBY MODE is LOW
POWER.
TEMPERATURE ALERT
Selects the notification method for an abnormal
temperature.
OFF�������������� Do not notify about an abnormal
temperature.
OSD & LED�� When an abnormal temperature is
detected, the power LED flashes in red
and green alternately and the screen
displays a message: TEMPERATURE.
LED�������������� When an abnormal temperature is
detected, the power LED flashes in red
and green alternately.
STATUS ALERT
Selects the notification method for a hardware error.
OFF�������������� Do not notify about the error.
OSD & LED�� When a hardware error is detected, the
power LED flashes in red and the screen
displays a message: STATUS [xxxx].
LED�������������� When a hardware error is detected, the
power LED flashes in red.
POWER BUTTON
Normally, leave this setting as MONITOR.
When using an optional part, if instruction appears,
change the setting accordingly.
CONTROLLER INPUT
Normally, you do not need to change this setting.
When using an optional part, if instruction appears,
change the setting accordingly.
3. Press
MENU
to return to the normal screen.
TIPS
• When both abnormal temperature and hardware error are
detected, the hardware error notification overrides.
• If TEMPERATURE ALERT or STATUS ALERT is set to
OSD & LED, alert messages will appear even if the OSD
DISPLAY is set to ON 2 or OFF.
• If TEMPERATURE ALERT or STATUS ALERT is set to LED
or OSD & LED, the LED lights even if the LED function is
set to OFF.
31
E
Controlling the Monitor with a PC (RS-232C)
You can control this monitor from a PC via RS-232C (COM
port) on the PC.
You can also connect multiple monitors via a daisy chain by
using a PC. By assigning ID numbers to each monitor (see
page 34), you can make input mode selection/adjustment or
can check the status of a specific monitor.
Precautions when the PN-ZB02 (optional) is attached
• To control the monitor via RS-232C, set RS-232C/LAN
SELECT to RS-232C.
• You cannot use RS-232C and LAN control simultaneously.
PC connection
nOne-to-one connection with a PC
Connect with RS-232 straight cable between the PC’s COM
port (RS-232C connector) and the RS-232C input terminal on
the monitor.
Communication conditions
Set the RS-232C communication settings on the PC to match
the monitor’s communication settings as follows:
Baud rate
*
Stop bit
1 bit
Data length
8 bits
Flow control
None
Parity bit
None
* Set to the same baud rate as the BAUD RATE setting of
SETUP menu. (Initial setting: 38400 bps)
* When connecting multiple monitors in a daisy chain, set all
monitors to the same BAUD RATE.
Communication procedure
nCommand format
When a command is sent from the PC to the monitor, the
monitor operates according to the received command and
sends a response message to the PC.
Return code
C1
RS-232C input terminal
C2
C3
C4
P1
Command field
(4 prescribed
alphanumerical characters)
P2
P3
P4
Parameter field
(4 character string comprised of:
0-9, +, -, space, ?)
PC
To COM port
RS-232 straight cable
(commercially available)
nDaisy chain connection… Advanced operation
Connect with RS-232 straight cable between the PC’s COM
port (RS-232C connector) and the RS-232C input terminal on
the first monitor.
Next, connect RS-232 straight cable to the first monitor’s
RS‑232C output terminal and to the second monitor’s
RS-232C input terminal. Connect in the same way to the third
and subsequent monitors.
Up to 25 monitors can be connected. (Depending on the
length of the cable used and the surrounding environment.)
First monitor
Second monitor
Example: VOLM0030
VOLM
30
* Be sure to input 4 characters for the parameter. Pad with
spaces (“ ”) if necessary.
(“
” is a return code (0DH, 0AH or 0DH))
Wrong : VOLM30
Right : VOLM
30
When inputting a negative value, specify a numerical value in
three digits.
Example: AUTR-005
Do not use spaces for MPOS, DATE, and SC01 through
SC08. Specify parameters using a specified number of
characters.
Example: MPOS010097
If a command has “R” listed for “DIRECTION” in the
“RS-232C command table” on page 37, the current value can
be returned by using “?” as the parameter.
RS-232C
output terminal
Example:
RS-232C
input terminal
VOLM ? ? ? ?
←
From PC to monitor (How much
is current volume setting?).
30
←
From monitor to PC (Current
volume setting: 30).
* If an ID number (see page 33) has been assigned
(For example, ID number = 1).
PC
VOLM
To COM port
E
32
RS-232 straight cables
(commercially available)
30
001
?
← From PC to monitor.
← From monitor to PC.
Controlling the Monitor with a PC (RS-232C)
nResponse code format
When RS-232C/LAN SELECT is set to LAN
When a command has been executed correctly
O
K
Return code
(0DH, 0AH)
Space (20H)
SPC
0
0
1
ID number of responding monitor
When a command has not been executed
E
R
R
Return code
(0DH, 0AH)
Return code
(0DH, 0AH)
Space (20H)
R
E
L
E
C
T
R
SPC
0
E
D
0
nCommunication interval
• After OK or ERR is returned, you must send the following
commands.
To set a timeout for the command response, specify 10
seconds or longer.
When connecting multiple monitors in a daisy chain, set the
timeout to at least the product of the monitor’s position from
the computer multiplied by 10 seconds.
Example) 3rd monitor from computer: 30 seconds or longer.
• Provide an interval of 100 ms or more between the
command response and the transmission of the next
command.
VOLM0020
OK
* If an ID number has been assigned
E
S
Return code
(0DH, 0AH)
* If an ID number has been assigned
K
N
Return code
(0DH, 0AH)
A response is returned after a command is executed.
O
U
Interval of 100 ms or more
1
INPS0001
WAIT
OK
ID number
TIPS
• “ERR” is returned when there is no relevant command or
when the command cannot be used in the current state of
the monitor.
• If communication has not been established for reasons
such as a bad connection between the PC and monitor,
nothing is returned (not even ERR).
• “ERR” may be returned when a command can’t be
received correctly due to interference from the surrounding
environment.
Please ensure that the system or software retries the
command if this occurs.
• If no monitor has been assigned the designated ID number
(e.g. if the command IDSL0002
is used, but no monitor
with ID number: 2 is found), no response is returned.
TIPS
• When executing ALL RESET, set the timeout period to 30
seconds or longer.
• When turning the power on while the POWER ON DELAY
function is in use, set the timeout period to the POWER ON
DELAY period + 10 seconds or longer.
If execution of the command is taking some time
W
A
I
T
Return code
(0DH, 0AH)
When the following commands are used, “WAIT” is returned.
In this case, a value will be returned if you wait a while. Do not
send any command during this period.
No ID number is attached to WAIT response.
• Commands which return WAIT:
1. When repeater control is used
2. When an IDSL or IDLK command is used
3. When one of the following commands is used: RSET,
INPS, ASNC, WIDE, EMAG, EPOS, PXSL, POWR,
AGIN, MWIN, MWIP, MWPP, ESTG, EMHV, EPHV,
ESHV, ENLG
When control via RS-232C is locked (to prevent use)
using the operation lock function (see page 31)
L
O
C
K
E
D
Return code
(0DH, 0AH)
33
E
Controlling the Monitor with a PC (RS-232C)
Advanced operation
This section explains commands for daisy chain connection.
The basic communication procedure is the same as in the
“One-to-one connection with a PC” section.
nCommands for ID control
The command examples shown on this page assume the
following connection and ID number set up.
ID number: 1
ID number: 2
ID number: 3
ID number: 4
nID numbers
You can assign a unique ID number to each monitor (see
page 24). This allows you to control a particular monitor in a
daisy chain of monitors.
You can assign ID numbers either from the menu screen (using
the remote control) or from the PC using RS-232 cable.
[Example]
ID number: 1
ID number: 2
ID number: 3
ID number: 4
IDST��������.A monitor receiving this command sets its own ID
number in the parameter field.
Example:
IDST0001
OK
001 ← The ID number of this monitor is set to 1.
TIPS
If monitors are connected as shown above, you can
execute commands like “Set the volume of the monitor with
ID 4 to 20”.
When designating ID numbers for a set of monitors linked in a
daisy chain, you should basically avoid any duplication of ID
numbers.
ID numbers do not have to be assigned in ascending order
starting from the PC. They can also be connected as shown
below.
[Example]
ID number: 3
ID number: 2
ID number: 4
ID number: 1
You can automatically assign ID numbers by using the IDST
command with the Repeater control (see “Repeater control”
on page 35).
For example, using the command “IDST001+” automatically
sets the ID numbers, as shown below.
[Example]
ID number: 1
IDST001 +
ID number: 2
ID number: 3
ID number: 4
← ID setting command with repeater control
WAIT
OK
001
← “OK” response from ID number: 1
OK
002
← “OK” response from ID number: 2
OK
003
← “OK” response from ID number: 3
OK
004
← “OK” response from ID number: 4 (End)
IDSL��������The parameter of this command sets the ID number
of the monitor. The monitor is subject to the next
command.
Example:
The next command is for the monitor
IDSL0002
← with ID number: 2.
WAIT
←
OK
002
Searching for monitor with ID number:
2
← Found monitor with ID number: 2
Sets volume of monitor with ID
VOLM0030
← number: 2 to 30.
WAIT
← Processing
OK
002
OK response from monitor with ID
← number: 2
VOLM0020
← Sets volume to 20.
OK
← number: 1 (the one directly connected
001
The volume of the monitor with ID
to the PC) is set to 20.*
* The IDSL command is effective only once, for the
immediately succeeding command.
E
34
Controlling the Monitor with a PC (RS-232C)
IDLK��������The parameter of this command sets the ID
number of the monitor. The monitor is subject to all
subsequent commands.
Example:
IDLK0002
WAIT
OK
Following commands are for the monitor
← with ID number: 2.
←
002
Searching for monitor with ID number:
2
Sets volume of monitor with ID
← number: 2 to 30.*
WAIT
← Processing
002
VOLM0020
This system has a function to allow setting of multiple
monitors connected in a daisy chain using a single command.
This function is called repeater control. You can use Repeater
control function without assigning ID numbers.
[Example]
Set 1
Set 2
Set 3
Set 4
← Found monitor with ID number: 2
VOLM0030
OK
nRepeater control
* If monitors are connected as shown above, you can
execute a command like “Set all monitors’ input settings to
PC D-SUB”.
Sets volume of monitor with ID
← number: 2 to 20.*
WAIT
OK
002
IDLK0000
← Canceling fixed ID number setting
WAIT
← Canceling IDLK
OK
002
← Cancelation complete
VOLM0010
OK
001
The volume of the monitor with ID number:
← 1 (the one directly connected to the PC) is
set to 10. (IDLK is canceled.)
* The IDLK command remains effective until it is
canceled, or power is shut off.
IDCK��������Provides screen display of the ID number currently
assigned to a monitor, and the ID number currently
set for IDLK (if any).
Example:
(After executing IDLK0002)
IDCK0000
← (Parameter has no meaning.)
ID : 001 IDLK : 002
← number is also displayed on the
IDCK000 +
← Repeater control. (If a command
WAIT
ID : 001 IDLK : 000
Returned response. The ID
monitor screen.
is used with repeater control, ID
designation using IDSL or IDLK
is canceled.)
ID : 002 IDLK : 000
ID : 003 IDLK : 000
ID : 004 IDLK : 000
35
E
Controlling the Monitor with a PC (RS-232C)
nRepeater control command
Repeater control is achieved by setting the FOURTH
CHARACTER of the parameter to “+”.
Example:
VOLM030 +
← Sets volume of all monitors to 30.
In repeater control, responses are returned by all the
connected monitors.
If you want to determine that a value has been returned by a
specific set, assign ID numbers to each monitor in advance.
When some monitors do not return their responses, the
probable cause is that the monitors could not receive the
command or command processing is not complete. Do not
send a new command.
Setting of the GAMMA user data
nTo transfer the GAMMA user data
Use the user data transfer commands (UGRW, UGGW and
UGBW). For each of the R, G and B colors, divide the total
512 pieces of user data into 16 blocks, and transfer 32 pieces
of data with each command.
C1
C2
Command field
002
OK
003
OK
004
← If 4 monitors are connected in
a chain, reliable operation can
be ensured by sending a new
command only after a reply
has been returned by 4th (last)
monitor.
Example:
002
30
003
30
004
…
S1
S2
Checksum field
One piece of data consists
of 4 digits.
32 pieces of data
Checksum
nSaving the GAMMA user data
Use the user data save command (UGSV) to save the
transferred user data in the monitor.
If the data is not saved, it will be cleared when:
• The main power switch is off
• STANDBY MODE is LOW POWER and the monitor enters
standby mode
To activate the transferred user data, select USER for GAMMA
of the PICTURE menu, or send the corresponding RS-232C
command.
WAIT
20
P4
nActivating the GAMMA user data
VOLM ? ? ? +
001
P3
* If data is less than 4 digits, add a “0” (zero) to make it 4
digits.
* The checksum field is the character string (ASCII) data of
lower-order one byte which indicates the sum of the block
number and 32 pieces of data in hexadecimal (0 to F).
Repeater control can also be used for reading settings.
10
P2
Block number (01 to 16) Data field
Command Block number
WAIT
OK
P1
UGRW 01000000010002 … 0031C0
VOLM030 +
001
C4
Example: To transfer the data of block 1 (0 to 31 levels)
of red (R) data
Example: (When 4 monitors are connected, and
assigned ID numbers: 1 through 4)
OK
C3
Volume settings for all
monitors are returned.
TIPS
• If repeater control is used during ID designation (IDSL,
IDLK), the ID designation is canceled.
nChecking the GAMMA user data
Use the user data read commands (UGRR, UGGR and
UGBR) to return 512 pieces of user data for each of the R,
G and B colors. Divide the data into 16 blocks and return 32
pieces of data with each command. The value to be returned
is not the value stored in the monitor, but the value in the
temporary memory for display. (These values are the same
when the user data save command (UGSV) above has been
sent.)
TIPS
• The user data is not initialized by RESET of the PICTURE
menu. To initialize the user data, use ALL RESET of the
FUNCTION menu.
The GAMMA user data initialize command (UGRS) allows
the initialization of the user data only.
E
36
Controlling the Monitor with a PC (RS-232C)
RS-232C command table
How to read the command table
Command:
Command field (See page 32.)
Direction:
W When the “Parameter” is set in the parameter field (see page 32), the command functions as described
under “Control/Response Contents”.
R The returned value indicated under “Reply” can be obtained by setting “????”, “
?” or “???+”
(repeater control) in the parameter field (see page 32).
Parameter:
Parameter field (See page 32.)
Reply:
Response (Returned value)
*1:
“●” indicates a command which can be used in power standby mode regardless of the STANDBY MODE
setting.
“○” indicates a command which can also be used in power standby mode when STANDBY MODE is set to
STANDARD.
“–” indicates a command which cannot be used in power standby mode regardless of the STANDBY MODE setting.
*2:
PN-ZB02 (optional) limitations
(A) When PN-ZB02 (optional) is not attached, (B) When PN-ZB02 (optional) is attached.
○: The command can be used.
- : Error (ERR)
Power control/Input mode selection
Function
POWER CONTROL
Command
Direction
POWR
W
Parameter
Reply
0
1
R
Control/Response contents
*1
*2
(A) (B)
Switches to standby mode.
Returns from standby mode.
0 Standby mode
1 Normal mode
● ○ ○
2 Input signal waiting mode
INPUT MODE SELECTION
INPS
W
R
0
Toggle change for input mode. Terminals not selected in INPUT SELECT
cannot be selected.
1
PC DVI-D
“ERR” when AV DVI-D is selected for DVI of INPUT SELECT.
2
PC D-SUB
3
AV COMPONENT
“ERR” when PC RGB is selected for BNC of INPUT SELECT.
4
AV VIDEO
6
PC RGB
“ERR” when AV COMPONENT is selected for BNC of INPUT SELECT.
7
AV DVI-D
“ERR” when PC DVI-D is selected for DVI of INPUT SELECT.
8
AV S-VIDEO
9
AV HDMI
“ERR” when PC HDMI is selected for HDMI of INPUT SELECT.
○
○
○ ○
10
PC HDMI
“ERR” when AV HDMI is selected for HDMI of INPUT SELECT.
○ ○
○ ○
○
○ ○
- ○
- ○
● ○
-
-
-
1 PC DVI-D
2 PC D-SUB
3 AV COMPONENT
4 AV VIDEO
6 PC RGB
7 AV DVI-D
● ○ ○
8 AV S-VIDEO
9 AV HDMI
10 PC HDMI
37
E
Controlling the Monitor with a PC (RS-232C)
SCREEN menu
Function
Command
Direction
Auto
ASNC
W
CLOCK
CLCK
WR
PHASE
positioning
size
RESOLUTION
RESET
E
38
Parameter
Reply
Control/Response contents
1
When the input mode is PC D-SUB, PC RGB.
0-1200
0-1200 When the input mode is PC D-SUB, PC RGB.
Varies depending on the signal.
PHSE
WR
0-63
Position of the longest direction
HPOS
WR
0-100
0-100 0-800 on PC D-SUB, PC RGB.
Varies depending on the signal.
Position of the shortest direction
VPOS
WR
0-100
0-100 0-200 on PC D-SUB, PC RGB.
Varies depending on the signal.
SIZE of the longest direction
HSIZ
WR
0-100
0-100
SIZE of the shortest direction
VSIZ
WR
0-100
0-100
Longest direction resolution
HRES
WR
300-1920
300-1920 When the input mode is PC D-SUB, PC RGB.
Only even numbers are valid for parameters.
Varies depending on the signal.
Shortest direction resolution
VRES
WR
200-1200
200-1200
ARST
W
1
*1
*2
(A) (B)
0-63 When the input mode is PC D-SUB, PC RGB.
-
○ ○
Controlling the Monitor with a PC (RS-232C)
PICTURE menu
Function
Command
Direction
Auto
AGIN
W
1
When the input mode is PC D-SUB, PC RGB.
ANALOG GAIN
ANGA
WR
0-127
0-127 When the input mode is PC D-SUB, PC RGB.
ANALOG OFFSET
ANOF
WR
0-127
0-127 When the input mode is PC D-SUB, PC RGB.
CONTRAST
CONT
WR
0-60
0-60
BLACK LEVEL
BLVL
WR
0-60
0-60
TINT
TINT
WR
0-60
0-60
COLORS
COLR
WR
0-60
0-60
SHARPNESS
SHRP
WR
0-24
0-24
RGB INPUT RANGE (AV HDMI)
AHDR
WR
0-2
0-2 0: AUTO, 1: FULL, 2: LIMITED
RGB INPUT RANGE (PC HDMI)
PHDR
WR
0-2
0-2 0: AUTO, 1: FULL, 2: LIMITED
RGB INPUT RANGE (AV DVI)
ADVR
WR
1-2
1-2 1: FULL, 2: LIMITED
RGB INPUT RANGE (PC DVI)
PDVR
WR
1-2
1-2 1: FULL, 2: LIMITED
RGB INPUT RANGE (D-SUB)
PDSR
WR
1-2
1-2 1: FULL, 2: LIMITED
RGB INPUT RANGE (PC BNC)
PBRR
WR
1-2
1-2 1: FULL, 2: LIMITED
FLESH TONE
FLES
WR
0-2
0-2 0: OFF, 1: LOW, 2: HIGH
3D-NR
TDNR
WR
0-2
0-2 0: OFF, 1: LOW, 2: HIGH
MPEG-NR
MPNR
WR
0-1
0-1 0: OFF, 1: ON
3D-Y/C
YCSP
WR
0-1
C.M.S.-HUE
CMHR
WR
-10-10
ADVANCED
(When the input
mode is AV.)
Parameter
Reply
Control/Response contents
CMHY
Y
CMHG
G
CMHC
C
CMHB
B
WHITE BALANCE
THRU
W
CMSR
WR
1
-10-10
Y
G
CMSC
C
CMSB
B
-
○
M
CRST
W
CMVR
WR
2
-10-10
Resets the saturation.
-10-10 R
CMVY
Y
CMVG
G
CMVC
C
CMVB
B
○
M
CRST
W
3
BMOD
WR
0
0 STD
2
2 VIVID
3
3 sRGB (When the input mode is PC)
4
4 HIGH ILLUMINANCE
WR
0
1-18
USER
99
Resets the brightness.
0 When the input mode is PC DVI-D/PC HDMI.
99
CRTR
WR
0-256
0-256 “ERR” when CTMP is not set to 99.
G-CONTRAST
CRTG
WR
0-256
0-256
B-CONTRAST
CRTB
WR
0-256
0-256
R-OFFSET
OFSR
WR
-127-127
-127-127
G-OFFSET
OFSG
WR
-127-127
-127-127
B-OFFSET
OFSB
WR
-127-127
-127-127
COPY TO USER
CPTU
W
GAMMA
GAMM
WR
WR
0
Copies a preset value to the user setting.
0-2
0-2 0: 1.8, 1: 2.2, 2: 2.4 (during PC input)
0: LIGHT 2, 2: DARK (during AV input)
4-6
4-6 4: USER, 5: 2.0, 6: STD (during PC input)
4: USER, 5: LIGHT 1, 6: STD (during AV input)
0
0 No pattern display.
1
1 White single color pattern display.
2
2 Red single color pattern display.
3
3 Green single color pattern display.
4
99
○
○
-
○
4 Blue single color pattern display.
99 Red/green/blue mixed color pattern display.
Set each color's level with RED, GREEN, BLUE.
RED
PTDR
WR
0-15
0-15 “ERR” when PTDF is not set to 99.
GREEN
PTDG
WR
0-15
0-15
BLUE
PTDB
WR
0-15
0-15
RESET
ARST
W
2
○
1-18 From 1: approximately 3,000K to 15: approximately 10,000K
(500K steps)
16: approximately 5,600K, 17: approximately 9,300K,
18: approximately 3,200K
R-CONTRAST
PTDF
○
Resets the hue.
CMSG
PRESET
DISPLAY COLOR PATTERN
○
○
-10-10 R
CMSY
CTMP
○
M
CRST
CMVM
COLOR MODE
-
0-1 0: OFF, 1: ON (When the input mode is AV VIDEO)
CMSM
C.M.S.-VALUE
*2
(A) (B)
-10-10 R
CMHM
C.M.S.SATURATION
*1
-
39
E
Controlling the Monitor with a PC (RS-232C)
AUDIO menu
Function
Command
Direction
Parameter
Reply
Control/Response contents
TREBLE
AUTR
WR
-5-5
BASS
AUBS
WR
-5-5
-5-5
BALANCE
AUBL
WR
-10-10
-10-10
RESET
ARST
W
Command
Direction
OSD H-POSITION
OSDH
WR
0-100
0-100
OSD V-POSITION
OSDV
WR
0-100
0-100
*1
*2
(A) (B)
-5-5
○
3
○ ○
-
SETUP menu
Function
Parameter
Reply
Control/Response contents
MONITOR
STDR
WR
0-1
0-1
LANG
WR
14
14
ENGLISH
1
1
DEUTSCH
2
2
FRANÇAIS
3
3
ITALIANO
4
4
ESPAÑOL
5
5
РУССКИЙ
6
6
PWOD
WR
0
0
1-60
1-60
OFF
ON
FNCM
WR
0-1
0-1
0: MODE1, 1: MODE2
STANDBY MODE
STBM
WR
0-1
0-1
0: STANDARD, 1: LOW POWER
(“ERR" when SCHEDULE is effective or OFF is selected for LED.)
OFF IF NO OPERATION
ATOF
WR
0-1
0-1
0: OFF, 1: ON
HOT PLUG CONTROL (DVI)
HPCT
WR
0-1
0-1
0: OFF, 1: ON
HOT PLUG CONTROL (HDMI)
HPCH
WR
0-1
0-1
0: OFF, 1: ON
RS-232C/LAN SELECT
CTLS
WR
0-1
0-1
0 : RS-232C 1 : LAN
ID NUMBER
IDST
W
0-255
R
Sets the monitor’s ID number. (“0” means “no ID number”.)
0-255
ID NO. SETTING
(ONCE)
IDSL
W
1-255
ID NO. SETTING
(SUBSEQUENT)
IDLK
W
1-255
ID CHECK
IDCK
W
0
ID DISPLAY
IDDP
W
0-2
Sets a monitor ID number.
This ID number is effective for the next and all subsequent commands
after this command.
0: OFF, 1: ON, 2: ON (turns OFF after 4 sec.)
(When the PN-ZB02 is attached, the IP address and MAC address are
both displayed.)
BAUD
WR
0-2
0-2
0: 9600bps, 1: 19200bps, 2: 38400bps
WR
0-1
0-1
0: OFF, 1: ON
BRIGHTNESS SENSOR (When
connected to the PN-ZR01 (optional)
only)
OPTS
WR
0-2
0-2
0: OFF, 1: ON, 2: ON: DISPLAY
WHEN DARK:
AMBIENT
BRIGHTNESS
OPSD
WR
0-99
0-99
WHEN DARK:
SCREEN
BRIGHTNESS
OPDD
WR
0-30
0-30
WHEN LIGHT:
AMBIENT
BRIGHTNESS
OPSL
WR
1-100
1-100
WHEN LIGHT:
SCREEN
BRIGHTNESS
OPDL
WR
1-31
1-31
CPMD
WR
LOGO SCREEN
40
BTSC
WR
WR
○
○
○
○ - ○
○ ○ ○
○ - ○
○ ○ ○
Displays monitor’s own ID number and the selected ID number on the
screen.
HDAW
CPTG
○
Clears the ID number if one has been designated.
ID
: xxx
IDLK : yyy
BAUD RATE
SETTING COPY TARGET
○ ○
Returns the monitor’s ID number.
HDMI AUTO VIEW
SETTING COPY MODE
○
Clears the ID number if one has been designated.
0
BRIGHTNESS
SENSOR
SETTING (When
connected to
the PN-ZR01
(optional) only)
○
Sets a monitor ID number.
This ID number is only effective for the command immediately after this
command.
0
E
0: LANDSCAPE, 1: PORTRAIT
OPERATION MODE
ID NO. SETTING
*2
(A) (B)
○
LANGUAGE
Power On Delay
*1
○ ○ ○
○ ○ ○
○ ○ ○
○ ○ ○
0
0
1-225
1-225
Copy to all monitors.
0
0
Copies the PICTURE menu settings.
1
1
Copies all the settings.
0-1
0-1
Copy to the monitor with the set ID Number.
0: OFF, 1: ON
○ ○ ○
Controlling the Monitor with a PC (RS-232C)
OPTION menu
Function
Command
Direction
Date/time setting
DATE
WR
DATE DISPLAY FORMAT
DTFT
WR
TIME DISPLAY FORMAT
TMFT
WR
SCHEDULE
SC01SC08
WR
SCHEDULE BRIGHTNESS
INPUT SELECT
AUDIO SELECT
SB01SB08
WR
DVI
DVSL
BNC
Parameter
Reply
AABBCCDDEE
Control/Response contents
AABBCCDDEE
0-2
0-1
ABCDEFFGGH
0-2
0: YYYY/MM/DD, 1: MM/DD/YYYY, 2: DD/MM/YYYY
YYYY: Year, MM: Month, DD: Day
0-1 0: 24-HOUR TIME, 1: 12-HOUR TIME
Schedule of a specified number
A: Schedule
0= Not effective, 1 = Effective
B: Power
0 = OFF, 1 = ON
C: Day of the week 1 0 = Only once, 1 = Every week, 2 = Every day
D: Day of the week 2 0 = Sunday, 1 = Monday through 6 = Saturday,
9 = Not exist
E: Day of the week 3 0 = Sunday, 1 = Monday through 6 = Saturday,
9 = Not exist
F: Hour
00-23
G: Minute
00-59
H: Input
0 = Not specified, 1 = PC DVI-D/AV DVI-D,
2 = PC D-SUB, 3 = PC RGB/AV COMPONENT,
4 = AV VIDEO, 5 = AV S-VIDEO,
6 = PC HDMI/AV HDMI
“ERR” when LOW POWER is selected for STANDBY MODE.
○ ○ ○
0-31 Screen brightness to change
99
99 Disable brightness setting
WR
0-1
0-1 0: PC DVI-D, 1: AV DVI-D
BNSL
WR
0-1
0-1 0: PC RGB, 1: AV COMPONENT
HDMI
HDSL
WR
0-1
0-1 0: PC HDMI, 1: AV HDMI
PC DVI-D
ASDP
WR
1-3
1-3 1: AUDIO(STEREO MINI), 2: AUDIO1(RCA), 3: AUDIO2(RCA)
PC D-SUB
ASAP
WR
1-3
1-3 1: AUDIO(STEREO MINI)
PC HDMI
ASHP
WR
0-1
0-1 0: HDMI, 1: AUDIO(STEREO MINI)
2-3
2-3 2: AUDIO1(RCA), 3: AUDIO2(RCA)
PC RGB
ASCP
WR
1-3
1-3 1: AUDIO(STEREO MINI), 2: AUDIO1(RCA), 3: AUDIO2(RCA)
AV DVI-D
ASDA
WR
1-3
1-3 1: AUDIO(STEREO MINI), 2: AUDIO1(RCA), 3: AUDIO2(RCA)
AV HDMI
ASHA
WR
0-1
0-1 0: HDMI, 1: AUDIO(STEREO MINI)
2-3
2-3 2: AUDIO1(RCA), 3: AUDIO2(RCA)
AV COMPONENT
ASCA
WR
1-3
1-3 1: AUDIO(STEREO MINI), 2: AUDIO1(RCA), 3: AUDIO2(RCA)
-
AV S-VIDEO
ASSA
WR
1-3
1-3 1: AUDIO(STEREO MINI), 2: AUDIO1(RCA), 3: AUDIO2(RCA)
-
AV VIDEO
ASVA
WR
1-3
1-3 1: AUDIO(STEREO MINI), 2: AUDIO1(RCA), 3: AUDIO2(RCA)
-
RESOLUTION CHECK
PXCK
R
PIXEL SETTING
(PC D-SUB, PC
RGB)
PXSL
WR
○ ○ ○ ○
-
○
2: AUDIO1(RCA), 3: AUDIO2(RCA)
INPUT
RESOLUTION
(PC)
INPUT RESOLUTION (AV)
*2
(A) (B)
AA: Year, BB: Month, CC: Day, DD: Hour, EE: Minute
ABCDEFFGGH
0-31
*1
RESOLUTION CHECK
-
○
-
○
-
○
-
○
-
- Returns current resolution in the form of hhh, vvv.
0
0 768) 1366 x 768
1
1 768) 1360 x 768
2
2 768) 1280 x 768
3
3 768) 1024 x 768
5
5 480) 848 x 480
6
6 480) 640 x 480
7
7 1050) 1680 x 1050
8
8 1050) 1400 x 1050
9
9 768) AUTO
10
10 480) AUTO
- 480i, 480p, 1080i, 720p, 1080p, VGA , etc.
-
○ ○
RESO
R
ZOOM2 SPECIAL SETTING
(PC D-SUB, PC RGB)
Z2SP
WR
0-1
0-1 0: OFF, 1: ON
○
SCAN MODE
SCAN
WR
0-2
0-2 0: MODE1, 1: MODE2, 2: MODE3 (When the input mode is AV)
POWER MANAGEMENT (PC)
PMNG
WR
0-1
0-1 0: OFF, 1: ON
POWER MANAGEMENT (AV)
PMAV
WR
0-1
0-1 0: OFF, 1: ON
COLOR SYSTEM
CSYS
WR
0-5
0-5 0: AUTO, 1: PAL, 2: PAL-60, 3: SECAM, 4: NTSC3.58, 5: NTSC4.43
AUDIO OUTPUT(RCA)
AOUT
WR
0-1
0-1 0: VARIABLE, 1: FIXED
AUDIO OUTPUT(RCA)
When the PN-ZB02 (optional) is attached
AOUT
WR
0-2
0-2 0: VARIABLE1, 1: FIXED, 2: VARIABLE2
○
○
○
○ - ○
○ ○ -
AUDIO LEVEL(STEREO MINI)
AIVP
WR
0-1
0-1 0: 1.0Vrms, 1: 0.5Vrms
SELF ADJUST
AADJ
WR
0-1
0-1 0: OFF, 1: ON
AUTO INPUT CHANGE
AINC
WR
0-1
0-1 0: OFF, 1: ON
FAN SPEED
FCTL
WR
0-4
0-4 0: AUTO, 1-4: SPEED 1-4
-
○
-
○
○
○
○ ○
○
○
41
E
Controlling the Monitor with a PC (RS-232C)
MULTI menu
Function
Command
Direction
ENLARGE
ENLG
WR
0-1
ENLARGE MODE
EMAG
WR
0-4
EMHV
WR
11-55
11-55 1 x 1 (OFF) to 5 x 5 (“m x n” is expressed as “mn”, where m and n are
the numbers of monitors specified for the longest direction and the
shortest direction respectively.)
IMAGE POSITION (M x N)
EPHV
WR
11-55
11-55 Specifies values in the order of IMAGE POSITION IN LONGEST/
SHORTEST DIRECTION.
IMAGE POSITION (2 x 2)
EPOS
WR
0-3
IMAGE POSITION (3 x 3)
EPOS
WR
0-8
0-8
IMAGE POSITION (4 x 4)
EPOS
WR
0-15
0-15
IMAGE POSITION (5 x 5)
ENLARGED
SCREEN
POSITIONING
BEZEL WIDTH
Reply
Control/Response contents
*1
0-4 0: OFF, 1: 2 x 2, 2: 3 x 3, 3: 4 x 4, 4: 5 x 5
0-3 See the description below.
EPOS
WR
0-24
EPSH
WR
-999-999
-999-999 The setting range depends on the ENLARGE MODE setting and the
IMAGE POSITION.
0-24
THE SHORTEST
DIRECTION
EPSV
WR
-999-999
-999-999
BZCO
WR
0-1
0-1 0: OFF, 1: ON
TOP
BZCT
WR
0-1
0-1 0: OFF, 1: ON
BOTTOM
BZCB
WR
0-1
0-1 0: OFF, 1: ON
RIGHT
BZCR
WR
0-1
0-1 0: OFF, 1: ON
LEFT
BZCL
WR
0-1
TOP
BZWT
WR
0-100
-
0-1 0: OFF, 1: ON
0-100
BOTTOM
BZWB
WR
0-100
0-100
RIGHT
BZWR
WR
0-100
0-100
LEFT
BZWL
WR
0-100
0-100
ENLARGE/IMAGE POSITION SETTING ESTG
WR
XXYY
XXYY XX: ENLARGE MODE (Same as EMAG), YY: IMAGE POSITION (Same
as EPOS)
ESHV
WR
XXYY
XXYY XX: ENLARGE MODE (Same as EMHV), YY: IMAGE POSITION (Same
as EPHV)
• IMAGE POSITION (EPOS) setting
In landscape orientation
2x2
3x3
4x4
0
1
0
1
2
0
2
3
3
4
5
4
6
7
8
8
12
5x5
1
2
3
0
1
2
3
4
5
6
7
5
6
7
8
9
9
10
11
10
11
12
13
14
13
14
15
16
17
18
19
20
21
22
23
24
15
In portrait orientation
2x2
2
0
3
1
3x3
4x4
6
3
0
7
4
1
8
5
2
12
13
14
15
E
42
*2
(A) (B)
0-1 0: OFF, 1: ON
THE LONGEST
DIRECTION
BEZEL ADJUST
BEZEL ADJUST
Parameter
5x5
0
8
4
9
5
1
10
6
2
11
7
3
20
15
10
5
0
21
16
11
6
1
17
12
7
23
18
13
8
3
24
19
14
9
4
22
2
○ ○
Controlling the Monitor with a PC (RS-232C)
PIP/PbyP menu
Function
Command
Direction
PIP MODES
MWIN
WR
0-3
PIP SIZE
MPSZ
WR
1-64
PIP POS
The longest direction
MHPS
The shortest direction
MVPS
PIP POS LD+SD BATCH
W
Parameter
Reply
0-100
0-100
R
MPOS
W
0-100
0-100,0-100
R
PIP BLEND
MWBL
WR
PIP SOURCE
MWIP
WR
0-3 0: OFF, 1: PIP, 2: PbyP, 3: PbyP2
1-64
0-100
R
W
Control/Response contents
Specify the position in MPOSxxxyyy format.
(xxx: Longer side, yyy: Shorter side position)
0-100,0-100 Returns a response in (xxx,yyy) format.
(xxx: Longer side, yyy: Shorter side position)
0-15
0-15
1
1 PC DVI-D
2
2 PC D-SUB
3
3 AV COMPONENT
4
4 AV VIDEO
6
6 PC RGB
7
7 AV DVI-D
8
8 AV S-VIDEO
9
9 AV HDMI
10
10 PC HDMI
SOUND CHANGE
MWAD
WR
1-2
1-2 1: MAIN, 2: SUB
MAIN POS (Main screen)
MWPP
WR
0-1
0-1 0: POS1, 1: POS2
PbyP2 POS (Sub screen)
MW2P
WR
0-2
0-2 0: POS1, 1: POS2, 2: POS3
AUTO OFF
MOFF
WR
0-1
0-1 0: MANUAL, 1: AUTO
*1
*2
(A) (B)
○
○
○
○
○
○ ○ ○
○
○
○
- ○
○ ○
- ○
- ○
○ - ○
- ○
- ○
○ ○
- ○
○
○
○ ○
○
○
Initialization/Functional Restriction Setting (FUNCTION) menu
Function
ALL RESET
Command
Direction
RSET
W
Parameter
Reply
0
0-1
Control/Response contents
*1
0: ALL RESET
-
0: ALL RESET 1, 1: ALL RESET 2
-
ADJUSTMENT LOCK
ALCK
WR
0-2
0-2 0: OFF, 1:ON1, 2:ON2
ADJUSTMENT LOCK TARGET
ALTG
WR
0-2
0-2 0: REMOTE CONTROL, 1: MONITOR BUTTONS, 2: BOTH
OSD DISPLAY
LOSD
WR
0-2
0-2 0: ON1, 1: OFF, 2: ON2
LED
OFLD
WR
0-1
0-1 0: ON, 1: OFF
“ERR” when LOW POWER is selected for STANDBY MODE.
TEMPERATURE ALERT
TALT
WR
0-2
0-2 0: OFF, 1: OSD & LED, 2: LED
STATUS ALERT
SALT
WR
0-2
0-2 0: OFF, 1: OSD & LED, 2: LED
POWER BUTTON
PBTN
WR
0-1
0-1 0: MONITOR, 1: CONTROLLER
CONTROLLER INPUT
PCIP
WR
0-2
0-2 0: D-SUB, 1: HDMI (“ERR” when MONITOR is selected for POWER
BUTTON.)
2: DVI-D (“ERR” when MONITOR is selected for POWER BUTTON.)
*2
(A) (B)
○
-
-
○
○
○
○
○ ○ ○
○
○
○
○ ○ ○
○ - ○
43
E
Controlling the Monitor with a PC (RS-232C)
Others
Function
Command
Direction
SCREEN SIZE (PC)
WIDE
WR
1-5
1-5 1: WIDE, 2: NORMAL, 3: Dot by Dot, 4: ZOOM1, 5: ZOOM2
SCREEN SIZE (AV)
WIDE
WR
1-5
1-5 1: WIDE, 2: ZOOM1, 3: ZOOM2, 4: NORMAL, 5: Dot by Dot
VOLUME
VOLM
WR
0-31
MUTE
MUTE
WR
0-1
MODEL
INF1
R
SERIAL NO
INFORMATION
SRNO
R
BRIGHT
VLMP
WR
TEMPERATURE SENSOR
DSTA
R
Parameter
Reply
Control/Response contents
0-31
0-1 0: OFF, 1: ON
○
○
○
*2
(A) (B)
-
Value
●
Value
0-31
*1
0-31
0 Internal temperature normal
○
1 Internal temperature abnormal (Standby mode)
2 Internal temperature abnormal (Temperature is normal now, but it was
abnormal during operation.)
●
3 Internal temperature abnormal (Brightness of the backlight decreases.)
4 Temperature sensor abnormal
Temperature acquisition
CAUSE OF LAST STANDBY MODE
ERRT
STCA
R
Value Temperature at temperature sensors 1 through 4 are returned in the
following forms:
[Sensor 1], [Sensor 2], [Sensor 3], [Sensor 4]
Indicates a temperature sensor abnormality when “126” is returned.
W
0
○ ○
○
Initialization
R
0 No detectable error has occurred
1 Standby mode by POWER button
2 Main power off by the main power switch
3 Standby mode by RS-232C or LAN
4 Waiting mode by No Signal
●
6 Standby mode by abnormal temperature
8 Standby mode by SCHEDULE setting
20 Standby mode by OFF IF NO OPERATION setting
Commands for setting of the GAMMA user data
Function
E
Command
Direction
RED GAMMA DATA TRANSFER
UGRW
W
GREEN GAMMA DATA TRANSFER
UGGW
W
BLUE GAMMA DATA TRANSFER
UGBW
W
RED GAMMA DATA READ
UGRR
W
GREEN GAMMA DATA READ
UGGR
W
Parameter
Reply
aaxxxx ··· xxxxcc
(xxxx: 32 pieces)
aa: 01-16
xxxx: 0000-1023
cc: 00-FF
1-16 xxxx ··· xxxx
1-16 (xxxx: 32 pieces)
xxxx: 0000-1023
1-16
Control/Response contents
*2
(A) (B)
aa: Block number
xxxx: 32 pieces of user data
cc: Checksum (ASCII data) of the block number and user data
xxxx: User data of 32 pieces
BLUE GAMMA DATA READ
UGBR
W
USER DATA INITIALIZE
UGRS
W
0
Initialize the user data.
USER DATA SAVE
UGSV
W
0
Save the user data in the monitor.
44
*1
○ ○ ○
Controlling the Monitor with a PC (LAN)
When the PN-ZB02 (optional) is attached, your monitor can
be connected to a LAN allowing you to control it from a PC on
the LAN.
You can also configure the monitor to send e-mail notification
when it has a problem.
The connection requires a commercially available LAN cable
(UTP cable, Category 5, straight through).
Network (LAN)
Settings to connect to a LAN
Set the monitor’s IP address and subnet mask to match the
settings of your LAN.
These settings can be made on either the monitor or a PC
connected to the monitor.
The settings depend on the configuration of your LAN. Ask
your LAN administrator for details.
■ To set on the monitor
Set RS-232C/LAN SELECT on the SETUP menu to LAN, and
then set the LAN SETUP options. (See pages 24 and 25.)
MENU
After setting each item, select SET and press
.
LAN terminal
Hub
LAN cable (commercially available, straight)
TIPS
• You must assign an IP address to the monitor by following
the procedures in “Settings to connect to a LAN”. (See the
description on the right.)
• Your PC must be installed with Internet Explorer (version 7.0
or later).
• To control the monitor via LAN, set RS-232C/LAN SELECT
to LAN. (See page 24.)
• You cannot use RS-232C and LAN control simultaneously.
Initializing personal information
• When the PN-ZB02 (optional) is attached, personal
information such as e-mail addresses can be registered in
the monitor. Before transferring or disposing of the monitor, initialize all settings by selecting ALL RESET 1. (See
page 31.) Note that ALL RESET 2 will not initialize e-mail
addresses and other settings.
DHCP CLIENT
If your LAN has a DHCP server and you wish to obtain an
address automatically, change this setting to ON.
To set the address manually, set this to OFF.
IP ADDRESS
If the DHCP CLIENT is set to OFF, specify an IP address.
Press
or
to select items, and press
or
to
change the values.
SUBNET MASK
If the DHCP CLIENT is set to OFF, specify the subnet mask.
Press
or
to select items, and press
or
to
change the values.
DEFAULT GATEWAY
If the DHCP CLIENT is set to OFF, specify the default
gateway.
If you are not using a gateway, specify “0.0.0.0”.
Press
or
to select items, and press
or
to
change the values.
RESET
Resets the values of the LAN settings to the factory preset
values.
MENU
Select ON and then press
.
TIPS
• When manually setting the IP address, the IP address
for secondary monitors connected by RS-232C can be
automatically allocated. (See page 25.)
45
E
Controlling the Monitor with a PC (LAN)
■ To set from a PC
When the monitor is connected to a PC, LAN settings can be
configured via PC.
Set up process
(1) Connect your monitor to a PC
(2) Specify the PC’s IP address
(3) Configure the monitor’s LAN settings
7. Temporarily change the IP address and subnet mask.
To access the monitor as it is shipped from the factory, set
as follows.
• IP Address: 192.168.150.1
• Subnet Mask: 255.255.255.0
• Default Gateway: (leave blank)
(1) Connecting your monitor to a PC
Connect a commercially available crossover LAN cable
(UPT cable, Category 5) to the LAN port on the PC and this
monitor.
8. Click [OK] and then reboot the PC.
LAN terminal
TIPS
PC
To LAN terminal
LAN cable (commercially available, crossover)
(2) Specifying the PC’s IP address
To configure the monitor’s LAN settings, you must temporarily
change the settings on the PC.
This explanation is based on Windows 7.
1. Log on to the PC with an administrator account.
2. Click [Start], and then click “Control Panel”.
3. Click “View network status and tasks” in “Network and
Internet”.
In “Classic View”, click “Network and Sharing Center”.
4. Click “Local Area Connection” and then “Properties”.
5. Click “Internet Protocol Version 4 (TCP/IPv4)” and then
“Properties”.
6. Make a note of the current IP address, subnet mask, and
default gateway settings.
Make sure you write this information now as you will
be changing the IP address, subnet mask, and default
gateway settings back to these settings afterwards.
E
46
•
This monitor is factory preset as shown below.
(When DHCP CLIENT is set to OFF)
IP Address
: 192.168.150.2
Subnet Mask
: 255.255.255.0
Default Gateway : 0.0.0.0
(3) Configuring the monitor’s LAN settings
Access the monitor using Internet Explorer.
Controlling the monitor
1. Turn the power ON to the monitor.
2. Set RS-232C/LAN SELECT on the SETUP menu to LAN.
3. Set DHCP CLIENT to OFF in LAN SETUP on the SETUP
menu.
PC operation
4. Launch Internet Explorer, in the “Address” box type
“http://192.168.150.2/” and press the Enter key.
You will be prompted to enter a user name and password.
5. Leave the user name and password boxes blank and click
[OK].
6. Click on “LAN SETUP” under NETWORK.
Controlling the Monitor with a PC (LAN)
7. Specify the “DHCP CLIENT”, “IP ADDRESS”,etc.
Controlling with a PC
■ Basic operation
You use Internet Explorer on a PC on the LAN to control the
monitor.
1. Launch Internet Explorer on the PC.
2. In the “Address” box, type “http://” followed by your monitor’s
IP address followed by “/”, then press the Enter key.
You can confirm the IP address with the DISPLAY function.
DHCP CLIENT
If your LAN has a DHCP server and you wish to obtain an
address automatically, change this setting to “ON”.
To set the address manually, set this to “OFF”.
IP ADDRESS
If the DHCP CLIENT is set to “OFF”, specify an IP
address.
SUBNET MASK
If the DHCP CLIENT is set to “OFF”, specify the subnet
mask.
DEFAULT GATEWAY
If the DHCP CLIENT is set to “OFF”, specify the default
gateway.
If you are not using a default gateway, specify “0.0.0.0”.
8. When the setting is changed, click [Apply].
9. Check the message and click [OK].
10.Exit Internet Explorer.
11.Restore the PC’s IP address jotted in Step 6, “(2)
Specifying the PC’s IP address”.
12.Connect the monitor and the PC to the LAN.
Caution
• Wait 10 seconds after clicking [OK] before proceeding.
• When operating using the remote control unit or similar,
click [Refresh].
TIPS
• When manually setting the IP address, the IP address
for secondary monitors connected by RS-232C can be
automatically allocated. (See page 25.)
When prompted to enter a user name and password, type
the user name and password that you specified in the
security settings (see page 49), and click [OK].
If you did not make any security settings, leave the spaces
blank and click on [OK].
3. You can check, control, and change the monitor’s status
and settings by clicking the menu items on the left side of
the screen.
• If you see an [Apply] button next to a setting, click it after
you change that setting.
TIPS
• See pages 48 to 52 for details on each setting.
• If you click [Refresh] before the screen finishes updating
the current display, the “Server Busy Error” will appear.
Wait for a moment before operating your monitor again.
• You cannot operate the monitor while it is warming up.
DISPLAY
• If “DHCP CLIENT” is set to “ON”, press
on the
remote control unit two times and then check the monitor’s
IP address.
47
E
Controlling the Monitor with a PC (LAN)
■ INFORMATION
Information about this monitor appears.
■ ADJUSTMENT
You can adjust these settings which are also available on the
monitor’s menu.
• SCREEN (See page 23.)
• PICTURE (See page 23.)
• PICTURE (ADVANCED) (See page 30.)
• AUDIO (See page 24.)
• SETUP (See page 24.)
• OPTION (See page 26.)
• SCHEDULE (See page 29.)
• MULTI (See page 27.)
• PIP/PbyP (See page 27.)
• FUNCTION (See page 31.)
■ CONTROL
You can control the operations corresponding to the buttons
POWER INPUT SIZE
(
) on the remote control unit. (See pages 18
and 19.)
TIPS
• After changing DISPLAY COLOR PATTERN to OFF, click
[Refresh] to correctly retrieve the status of the monitor.
TIPS
• In standby mode, Power ON is the only operation available.
E
48
Controlling the Monitor with a PC (LAN)
■ NETWORK (LAN SETUP)
This screen allows you to set the settings necessary when the
monitor is connected to a LAN.
DHCP CLIENT
If your LAN has a DHCP server and you wish to obtain an
address automatically, change this setting to “ON”.
To set the address manually, set this to “OFF”.
IP ADDRESS
If the DHCP CLIENT is set to “OFF”, specify an IP address.
SUBNET MASK
If the DHCP CLIENT is set to “OFF”, specify the subnet
mask.
DEFAULT GATEWAY
If the DHCP CLIENT is set to “OFF”, specify the default
gateway.
If you are not using a default gateway, specify “0.0.0.0”.
DNS SERVER
Specify the DNS server address.
If you are not using a DNS server, specify “0.0.0.0”.
RESET
Clicking [Execute] returns all of the LAN SETUP settings
to the factory-preset values except for the DNS SERVER
setting.
■ NETWORK (SECURITY)
This screen allows you to specify the security-related settings.
USER NAME / PASSWORD
Sets up a user name and password to restrict access to this
monitor.
After entering a user name and password, click [Apply].
ACCEPT IP ADDRESS
You can limit access to this monitor by registering IP
addresses of PCs that should have access.
To limit access, specify the option “From only specific IP
addresses”. Otherwise, to allow access from any PC, specify
“All IP Addresses”.
IP ADDRESS 1 to 3
If “ACCEPT IP ADDRESS” is set to “From only specific IP
addresses”, enter the IP addresses that you want to allow.
TIPS
• The USER NAME and PASSWORD can be up to 8
alphanumeric characters or symbols.
• To cancel the user name and/or password after it has been
set, make the box empty and click [Apply].
TIPS
• When manually setting the IP address, the IP address
for secondary monitors connected by RS-232C can be
automatically allocated. (See page 25.)
49
E
Controlling the Monitor with a PC (LAN)
■ NETWORK (GENERAL)
This screen allows you to specify the general LAN settings.
MONITOR NAME
Specify a name for this monitor as it should appear on the
Internet Explorer screen.
AUTO LOGOUT TIME
Specify the time (in minutes) to elapse before automatically
disconnecting this monitor from the network.
Specify in minutes from 1 to 65535. A value of ‘0’ will disable
this function.
DATA PORT
Specify the TCP port number to use for exchanging data with
the monitor.
Specify a value from 1025 to 65535.
SEARCH PORT
Specify the port number to use when searching for this
monitor.
Specify a value from 1025 to 65535.
INSTALLATION INFORMATION (NAME/LOCATION)
Specify the information to display for this monitor in the
Internet Explorer window.
TIPS
• The MONITOR NAME can be up to 16 alphanumeric
characters or symbols.
• Enter up to 50 characters in the NAME field in the
INSTALLATION INFORMATION.
• Enter up to 100 characters in the LOCATION field in the
INSTALLATION INFORMATION.
E
50
■ MAIL (ORIGINATOR)
This screen allows you to configure the e-mail sent periodically
or when the monitor has an error.
The settings depend on the configuration of your LAN. Ask
your LAN administrator for details.
SMTP SERVER
Specify the SMTP server address for sending e-mail.
* When using a domain name, make sure to specify the
DNS SERVER as well. (See page 49.)
ORIGINATOR E-MAIL ADDRESS
Specify the e-mail address for this monitor.
This address becomes the e-mail address of the originator.
ORIGINATOR NAME
Specify the name for the originator.
This name appears in the “Originator Name” field of the
e-mail.
AUTHENTICATION
Specify the authentication method to use when sending
e-mail.
POP SERVER
If the “AUTHENTICATION” method is “POP before SMTP”,
specify the POP server address.
ACCOUNT NAME / PASSWORD
If the “AUTHENTICATION” method is “POP before SMTP”,
specify the account name and password to connect to the
POP server.
TIPS
• You can enter up to 64 alphanumeric characters or symbols
for the ORIGINATOR E-MAIL ADDRESS, ORIGINATOR
NAME, ACCOUNT NAME, and PASSWORD.
• The SMTP SERVER and POP SERVER can be up to 64
characters.
The following characters can be used: a-z, A-Z, 0-9, - , .
Controlling the Monitor with a PC (LAN)
■ MAIL (RECIPIENT)
This screen allows you to specify the recipients of the e-mail
sent periodically or when the monitor has an error.
RECIPIENT E-MAIL ADDRESSES
Specify the e-mail addresses to send error notification e-mail
to.
CONDITION
Specify the conditions to send mails.
When you check PERIODICAL, specify the date and time to
send the mails in the PERIODICAL setting.
CONFIRMATION
Sends test e-mail.
This allows you to confirm that the e-mail settings are
configured properly.
Attach the log file to a TEMPERATURE/HARDWARE error
e-mail.
When this option is checked, a log is added to the mail which
notifies a temperature or status error.
■ MAIL (PERIODICAL)
When PERIODICAL for CONDITION of MAIL (RECIPIENT) is
checked, set the date and time to send the mail.
DAY OF THE WEEK
Specify the day of the week to send the periodical mails.
TIME
Specify the time of the day to send the periodical mails.
Caution
• Do not turn off the main power when you set to send the
periodical mails.
• Specify the correct date and time. (See page 26.)
If the date and time settings are incorrect, the periodical
mail is not sent properly.
• Regularly confirm that the specified date and time is
correct.
• When LOW POWER is selected for STANDBY MODE,
periodical mails will not be sent in standby mode.
TIPS
• The RECIPIENT E-MAIL ADDRESSES can be up to 64
alphanumeric characters or symbols.
51
E
Controlling the Monitor with a PC (LAN)
■ SNMP
You can configure settings related to SNMP.
Caution
• After you set SNMP, click [Switch the main power of
monitor off and on now.] or turn off the monitor and then
turn it on again with the main power switch. When the
monitor restarts, wait about 30 seconds and then start the
next operation.
• If the IP address is changed while the SNMP function is
operational, turn off the monitor and then turn it on again
with the main power switch.
TIPS
• Depending on the SNMP settings, a short delay may occur
before the SNMP is usable. (About 2 minutes)
• Up to 16 alphanumeric letters and symbols can be used for
the community name, user name and password.
■ SERVICE & SUPPORT
(URL INFORMATION)
You can display a specific URL in the URL INFORMATION
field on the INFORMATION screen when an error occurs in
the monitor. (See page 48.)
SNMP SETTING
Set whether to enable or disable SNMP.
VERSION
Set the version of the SNMP to be supported.
COMMUNITY NAME 1 to 3
Set the name of the community required for the access.
USER 1 to 3
Set the user name, password, authentication method and
other options required for access.
TRAP SETTING
Set whether to enable or disable the trap function.
When this function is enabled, a trap will be sent when the
monitor is turned on.
TRAP SETTING OF AUTHENTICATION ERROR
Set whether the trap function sends a notification when
authentication fails.
TRAP ADDRESS & PORT
Set the destination address and port number of the
notification sent by the trap function.
E
52
URL INFORMATION
Enter the URL to display on the INFORMATION screen when
an error occurs on the monitor.
Up to 64 alphanumeric characters or symbols can be used.
CONDITION
Specify the condition to display the URL.
CONFIRMATION
The home page of the specified URL is displayed.
You can check whether the URL you entered is correct.
TIPS
• It is also possible to specify the message text, such as the
name of a contact or a telephone number, to be displayed
instead of the linked URL.
Troubleshooting
If you are experiencing any problem with your display, before
calling for service, please review the following troubleshooting
tips.
There is no picture or sound.
• Is the power cord disconnected? (See page 15.)
• Is the main power switch off? (See page 17.)
• Is the monitor in standby mode (the power LED illuminating
in orange)?
• Make sure correct input mode is selected. (See page 18.)
• If any external equipment is connected, make sure the
equipment is operating (playing back).
Remote control does not work.
• Are the batteries inserted with polarity (+,-) aligned? (See
page 15.)
• Are the batteries exhausted?
• Point the remote control unit toward the remote control
sensor.
• Is the menu display hidden or is operation disabled? (See
page 31.)
• Is the PN-ZR01 (optional) remote control sensor box
disconnected?
• If the main unit is connected to multiple monitors, is the
RS-232 cable disconnected? Has the ID No. been set?
Sound from left and right speakers is reversed.
Sound is heard from only one side.
• Are audio cables connected properly? (See pages 12 to
13.)
• Make sure audio cables for external speakers are
connected properly: left and right cables may be reversed
or one of the two cables may not be connected. (See page
13.)
• Check the setting of BALANCE for AUDIO menu. (See
page 24.)
There is a picture but no sound.
• Is the sound muted?
• Make sure the volume is not set to minimum.
• Are audio cables connected properly?
• Is the setting of AUDIO SELECT on the OPTION menu
correct? (See page 26.)
Unstable video.
• The signal may be incompatible.
• Try the automatic screen adjustment when the PC D-sub
input terminal or PC RGB input terminals are used.
The video from the PC/AV HDMI input terminal does not
appear properly.
• Is the setting for HDMI of INPUT SELECT on the OPTION
menu correct? (See page 26.)
• Is the HDMI cable HDMI standard compliant? The monitor
will not work with cables that are not standard compliant.
• Is the input signal compatible with this monitor? (See pages
57 to 58.)
The video from the PC/AV DVI-D input terminal does not
appear properly.
• Is the setting for DVI of INPUT SELECT on the OPTION
menu correct? (See page 26.)
• Is the input signal compatible with this monitor? (See pages
57 to 58.)
• Turn off the power to the connected equipment and then
turn the power on again.
• If the monitors are connected in a daisy chain, turn off the
power to all the monitors connected in a daisy chain and
then turn the power on again.
The video from PC RGB, AV COMPONENT, or AV VIDEO
does not appear correctly.
• Is the setting for BNC of INPUT SELECT on the OPTION
menu correct? (See page 26.)
• Is the input signal compatible with this monitor? (See pages
57 to 58.)
Control buttons do not work.
There is no picture.
• Load noises from outside may be interfering with normal
operation. Turn off the power and turn it on after waiting at
least 5 seconds, and then check the operation.
The input mode changes automatically.
• When the AUTO INPUT CHANGE is ON and no signal
is present in a selected input mode, the AUTO INPUT
CHANGE automatically changes the selected mode to a
mode where a video signal is present.
The input mode may change in the following cases:
-When a computer is in standby mode.
-When video play is stopped with a playback device.
Power LED flashes red.
“STATUS [xxxx]” appears in the corner of the screen.
• Hardware has a problem. Turn off the monitor and request
repair from your SHARP dealer.
(When STATUS ALERT is set to OSD & LED. This varies
depending on the setting.)
When “AUTO DIMMING” is displayed.
• When the internal temperature of the monitor rises
excessively, the brightness of the backlight automatically
decreases in order to prevent a further temperature rise. If
you attempt to use
to adjust the brightness while
the monitor is in this state, “AUTO DIMMING” is displayed
and you cannot change the brightness.
• Remove the cause of the excessive temperature rise.
The monitor makes a cracking sound.
• You may occasionally hear a cracking sound from the
monitor. This happens when the cabinet slightly expands
and contracts according to change in temperature. This
does not affect the monitor’s performance.
53
E
Troubleshooting
The Power LED is flashing in red and green alternately.
When “TEMPERATURE” is displayed in the corner of the
screen.
• When the internal temperature of the monitor rises
excessively, the brightness of the backlight decreases
automatically in order to prevent high-temperaturerelated problems. When this occurs, “TEMPERATURE” is
displayed on the screen and the Power LED flashes red
and green alternately. (When TEMPERATURE ALERT is
set to OSD & LED. This varies depending on the setting.)
• If the internal temperature rises further, the monitor
automatically enters standby mode. (The Power LED
continues flashing red and green alternately.)
• Remove the cause of the excessive temperature rise.
- If the monitor enters standby mode due to a rise in
temperature, to return to normal display, turn the power
switch off and then back on again. The monitor, however,
will enter standby mode again if the cause of the
temperature rise is not eliminated.
- Check whether the monitor is placed at a location where
a quick rise in temperature is likely. Internal temperature
rises quickly if the vents on the monitor are blocked.
- Internal temperature rises quickly if dust accumulates
inside the monitor or around the vents. Remove dust if
possible. Ask SHARP dealer about removing internal dust.
E
54
Specifications
nPN-V600 Product Specifications
Model
LCD component
Max. resolution
Max. colors
Pixel pitch
Viewing angle
Screen active area inch
Computer input signal
Sync signal
PN-V600
60" Class [60 inch (152.4cm) diagonal] TFT LCD
(pixels) 1366 x 768
Approx. 16.77 M colors
0.973 mm (H) × 0.973 mm (V)
176° right/left/up/down (contrast ratio ≥ 10)
(mm) 52-5/8 x 29-7/16 (1328.8 x 747.1)
Digital (DVI 1.0 standard-compliant), Analog RGB (0.7 Vp-p) [75 Ω]
Horizontal/vertical separate (TTL: positive/negative), Sync-on-green,
Composite sync (TTL: positive/negative)
Video color system
NTSC (3.58MHz)/NTSC (4.43MHz)/PAL/PAL-60/SECAM
Plug and play
VESA DDC2B
Power management
VESA DPMS, DVI DMPM
Input terminals
Digital
PC/AV
HDMI x 1
Analog
Mini D-sub 15 pin, 3 rows x 1
PC
Audio
3.5 mm mini stereo jack x 1
Serial (RS-232C)
D-sub 9 pin x 1
Digital
DVI-D 24 pin (HDCP compatible) x 1
When PN-ZB02 PC/AV
(optional) is
Analog
BNC *1*2 x 1
PC
attached
Composite video BNC x 1
AV
S-video
x1
Component
BNC (Y, Cb/Pb, Cr/Pr) *1 x 1
Audio
RCA pin (L/R) x 2
Output terminals
Audio
RCA pin (L/R) x 1
Serial (RS-232C)
D-sub 9 pin x 1
Digital
DVI-D 24 pin x 1
When PN-ZB02 PC/AV
(optional) is
External speaker
10 W + 10 W [6 Ω]
attached
LAN terminal
10 BASE-T/100 BASE-TX
[When PN-ZB02 (optional) is attached]
Power requirement
AC 100 V - 240 V, 50/60 Hz
Operating temperature *3
32°F to 104°F (0°C to 40°C)
Operating humidity
20% to 80% (no condensation)
305 W / 1.0 W / 1.0 W
Power consumption
(maximum / input signal waiting mode *4 / standby
mode *5)
Power consumption [PN-ZB02 (optional)]
310 W
Dimensions (excluding protrusions)
inch (mm) Approx. 52-5/8 (W) x 5-7/8 (D) x 29-11/16 (H) (1335.9 x 149.3 x 754.2)
Weight lbs. (kg) Approx. 90.4 (41)
lbs. (kg) Approx. 1.102 (0.5)
Weight [PN-ZB02 (optional)] *1
*2
*3
*4
*5
Cannot be used simultaneously.
Does not support plug and play.
Temperature condition may change when using the display together with the optional equipments recommended by SHARP.
In such cases, please check the temperature condition specified by the optional equipments.
When AUTO INPUT CHANGE is set to OFF.
When STANDBY MODE is set to STANDARD. When STANDBY MODE is set to LOW POWER: 0.5 W.
As a part of our policy of continuous improvement, SHARP reserves the right to make design and specification changes for product improvement
without prior notice. The performance specification figures indicated are nominal values of production units. There may be some deviations from
these values in individual units.
nPN-ZR01 (optional) Product Specifications
Model
PN-ZR01
Remote control sensor box dimensions inch (mm) Approx. 1-3/8 (W) x 7/8 (D) x 5-1/8 (H) (34.2 x 23 x 130)
Remote control sensor box weight lbs. (kg) Approx. 0.220 (0.1)
55
E
Specifications
nDimensional Drawings
Note that the values shown are approximate values.
52-5/8 [1335.9]
Unit: inch [mm]
5-7/8
[149.3]
VESA holes *
3-5/8
[92.3]
52-5/8 [1335.9]
7-7/8
7-7/8
[200]
[200]
3-15/16 3-15/16
[100] [100]
7-7/8 [200]
29-11/16 [754.2]
Opening height (29-7/16 [747.7])
Opening width (52-5/16 [1329.4])
When mounting the monitor, be sure to use a wall-mount bracket that complies with the VESA-compatible mounting method.
SHARP recommends using M6 screws and tighten the screws.
Note that screw hole depth of the monitor is 3/8 inch (10 mm). Loose mounting may cause the product to fall, resulting in
serious personal injuries as well as damage to the product. The screw and hole should come together with over 5/16 inch
(8 mm) length of thread. Use a bracket which has been approved for UL1678 standard, and which can endure at least 4 times
or more the weight of the monitor.
nPower management
This monitor conforms to VESA DPMS and DVI DMPM. Both your video card and computer must support the same standard in
order for the monitor’s power management function to work.
DPMS: Display Power Management Signaling
DMPM: Digital Monitor Power Management
DPMS
Screen
Power
consumption*1
Hsync
Vsync
DMPM
ON STATE
Display
305 W
Yes
Yes
Monitor ON
Display
305 W
No
Yes
Active OFF
No display
1.0 W*2
Yes
No
No
No
STANDBY
SUSPEND
OFF STATE
No
display
1.0 W*2
Screen
Power
consumption*1
*1 When PN-ZB02 (optional) is not connected.
*2 When AUTO INPUT CHANGE is set to OFF.
nDDC (plug and play)
The monitor supports the VESA DDC (Display Data Channel) standard.
DDC is a signal standard for plug and play between monitors and computers. Information about resolution and other parameters
is exchanged between the two. This function can be used if the computer supports DDC and it has been configured to detect
plug-and-play monitors.
There are several types of DDC, depending on the communication method used. This monitor supports DDC2B.
E
56
Specifications
nCompatible signal timing (PC)
Screen resolution
VESA
640 × 480
800 × 600
848 × 480
1024 × 768
1152 × 864*1
1280 × 768
1280 × 800*1
1280 × 960*1
1280 × 1024*1
Wide
US TEXT
Sun
1360 × 768
1400 × 1050*1
1440 × 900*1
1600 × 1200*1
1680 × 1050*1
1280 × 720
1366 × 768
1920 × 1080*1
720 × 400
1024 × 768
1152 × 900*1
1280 × 1024*1
1600 × 1000*1
Hsync
Vsync
Dot frequency
31.5kHz
37.9kHz
37.5kHz
35.1kHz
37.9kHz
48.1kHz
46.9kHz
31.0kHz
48.4kHz
56.5kHz
60.0kHz
67.5kHz
47.8kHz
60.3kHz
49.7kHz
60.0kHz
64.0kHz
80.0kHz
47.7kHz
65.3kHz
55.9kHz
75.0kHz
65.3kHz
44.7kHz
47.7kHz
66.3kHz
67.5kHz
31.5kHz
48.3kHz
53.6kHz
56.6kHz
61.8kHz
71.8kHz
71.7kHz
81.1kHz
68.6kHz
60Hz
72Hz
75Hz
56Hz
60Hz
72Hz
75Hz
60Hz
60Hz
70Hz
75Hz
75Hz
60Hz
75Hz
60Hz
60Hz
60Hz
75Hz
60Hz
60Hz
60Hz
60Hz
60Hz
60Hz
60Hz
60Hz
60Hz
70Hz
60Hz
66Hz
70Hz
66Hz
76.2Hz
67.2Hz
76Hz
66Hz
25.175MHz
31.5MHz
31.5MHz
36.0MHz
40.0MHz
50.0MHz
49.5MHz
33.75MHz
65.0MHz
75.0MHz
78.75MHz
108.0MHz
79.5MHz
102.25MHz
83.5MHz
108.0MHz
108.0MHz
135.0MHz
85.5MHz
121.75MHz
106.5MHz
162.0MHz
146.25MHz
74.4MHz
85.383MHz
148.5MHz
148.5MHz
28.3MHz
64.13MHz
70.4MHz
74.25MHz
94.88MHz
108.23MHz
117.01MHz
134.99MHz
135.76MHz
Digital
DVI*2
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
-
HDMI
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
-
Analog
(D-SUB/RGB*2)
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
*1 Displays a reduced image, except in Dot by Dot. In Dot by Dot, the image will be cut down to panel size then displayed.
*2 Available when the PN-ZB02 (optional) is attached.
* All are compliant only with non-interlaced.
* Depending on the connected PC, images may not be displayed properly even if the compatible signal described above is input.
* The frequency values for the Sun are reference values.
57
E
Specifications
nCompatible signal timing (AV)
Screen resolution
1920 × 1080p*1
1920 × 1080i*1
1280 × 720p
720 × 576p
720 × 480p
640 × 480p(VGA)
720(1440) × 576i
720(1440) × 480i
Frequency
24Hz
50Hz
59.94Hz
60Hz
50Hz
59.94Hz
60Hz
50Hz
59.94Hz
60Hz
50Hz
59.94Hz
60Hz
59.94Hz
60Hz
50Hz
59.94Hz
60Hz
DVI-D*2
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
-
HDMI
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Component
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
*1 Displays a reduced image, except in Dot by Dot. In Dot by Dot, the image will be cut down to panel size then displayed.
*2 Available when the PN-ZB02 (optional) is attached.
E
58
Specifications
nPC/AV DVI-D
(DVI-D 24 pin)
No.
input terminal pins
Function
No.
Function
nPC/AV HDMI input
(HDMITM Connector)
No.
Function
terminal pins
No.
Function
1
TMDS data 2-
13
N.C.
1
TMDS data 2+
11
TMDS clock shield
2
TMDS data 2+
14
+5V
2
TMDS data 2 shield
12
TMDS clock-
3
TMDS data 2/4 shield
15
GND
3
TMDS data 2-
13
CEC
4
N.C.
16
Hot-plug detection
4
TMDS data 1+
14
N.C.
5
N.C.
17
TMDS data 0-
5
TMDS data 1 shield
15
SCL
6
DDC clock
18
TMDS data 0+
6
TMDS data 1-
16
SDA
7
DDC data
19
TMDS data 0/5 shield
7
TMDS data 0+
17
DDC/CEC GND
8
N.C.
20
N.C.
8
TMDS data 0 shield
18
+5V
9
TMDS data 1-
21
N.C.
9
TMDS data 0-
19
Hot-plug detection
10
TMDS data 1+
22
TMDS clock shield
10
TMDS clock+
11
TMDS data 1/3 shield
23
TMDS clock+
12
N.C.
24
TMDS clock-
nPC D-sub input
(Mini D-sub 15 pin)
No.
terminal pins
Function
No.
nRS-232C input
(D-sub 9 pin)
Function
No.
terminal pins
Function
No.
Function
1
Red video signal input
9
+5V
1
N.C.
6
N.C.
2
Green video signal input
10
GND
2
Transmitted data
7
N.C.
3
Blue video signal input
11
N.C.
3
Received data
8
N.C.
4
N.C.
12
DDC data
4
N.C.
9
N.C.
5
GND
13
Hsync signal input
5
GND
6
GND for red video signal
14
Vsync signal input
7
GND for green video signal 15
8
GND for blue video signal
nPC/AV DVI-D
(DVI-D 24 pin)
No.
DDC clock
output terminal pins
Function
No.
Function
nRS-232C output
(D-sub 9 pin)
No.
Function
terminal pins
No.
Function
1
TMDS data 2-
13
N.C.
1
N.C.
6
N.C.
2
TMDS data 2+
14
+5V
2
Received data
7
N.C.
3
TMDS data 2/4 shield
15
GND
3
Transmitted data
8
N.C.
4
N.C.
16
Hot-plug detection
4
N.C.
9
N.C.
5
N.C.
17
TMDS data 0-
5
GND
6
DDC clock
18
TMDS data 0+
7
DDC data
19
TMDS data 0/5 shield
8
N.C.
20
N.C.
9
TMDS data 1-
21
N.C.
10
TMDS data 1+
22
TMDS clock shield
11
TMDS data 1/3 shield
23
TMDS clock+
12
N.C.
24
TMDS clock-
59
E
Mounting Precautions (For SHARP dealers and service engineers)
• When installing, removing or moving the monitor, ensure that this is carried out by at least 2 people.
• Be sure to use a wall-mount bracket designed or designated for mounting the monitor.
• This monitor is designed to be installed on a concrete wall or pillar. Reinforced work might be necessary for some materials
such as plaster / thin plastic board / wood before starting installation.
This monitor and bracket must be installed on a wall which can endure at least 4 times or more the weight of the monitor.
Install by the most suitable method for the material and the structure.
• To attach a VESA-compliant mounting bracket, use M6 screws that are 5/16 inch (8 mm) to 3/8 inch (10 mm) longer than the
thickness of the mounting bracket.
• When moving the monitor, be sure to hold it with either handles or the corners on the bottom of the unit. Do not hold the LCD
panel. This may cause product damage, failure, or injury.
• When performing an installation where the monitor is stacked, please install it such that load is not placed on the monitor
frame.
• After mounting, please carefully ensure the monitor is secure, and not able to come loose from the wall or mount.
• Do not use any screw holes other than VESA holes for installation.
E
60
PN-V600 Me EN11L(1)