AV SURROUND RECEIVER
AVR-590
Owner’s Manual
Manuel de l’Utilisateur
bThe illustrations used for explaining operations in this manual show the buttons of
the remote control unit.
The same operations can be performed using the buttons with the same names on
the main unit panel.
b Les illustrations des boutons présentes dans ce manuel servent à expliquer le
fonctionnement de la télécommande.
Vous pouvez contrôler l’appareil à l’aide du bouton portant le même nom sur la
façade de l’appareil.
ENGLISH FRANCAIS
nSAFETY PRECAUTIONS
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral
triangle, is intended to alert the user to the presence of
uninsulated “dangerous voltage” within the product’s enclosure
that may be of sufficient magnitude to constitute a risk of electric
shock to persons.
The exclamation point within an equilateral triangle is intended
to alert the user to the presence of important operating
and maintenance (servicing) instructions in the literature
accompanying the appliance.
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT
EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
CAUTION:
HOT SURFACE. DO NOT TOUCH.
The top surface over the internal heat sink may become
hot when operating this product continuously.
PRECAUTION:
SURFACE CHAUDE. NE PAS TOUCHER.
La surface supérieure du dissipateur de chaleur peut
devenir chaude si vous utilisez ce produit en continu.
I
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
IMPOTANT SAFETY
INSTRUCTIONS
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings.
Install in accordance with the manufacturer’s instructions.
Do not install near any heat sources such as radiators, heat registers,
stoves, or other apparatus (including amplifiers) that produce heat.
Do not defeat the safety purpose of the polarized or grounding-type plug. A
polarized plug has two blades with one wider than the other. A grounding
type plug has two blades and a third grounding prong. The wide blade or the
third prong are provided for your safety. If the provided plug does not fit into
your outlet, consult an electrician for replacement of the obsolete outlet.
Protect the power cord from being walked on or pinched particularly at
plugs, convenience receptacles, and the point where they exit from the
apparatus.
Only use attachments/accessories specified by the manufacturer.
Use only with the cart, stand, tripod, bracket, or table
specified by the manufacturer, or sold with the apparatus.
When a cart is used, use caution when moving the cart/
apparatus combination to avoid injury from tip-over.
Unplug this apparatus during lightning storms or when
unused for long periods of time.
14. Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been damaged in any way,
such as power-supply cord or plug is damaged, liquid has been spilled or
objects have fallen into the apparatus, the apparatus has been exposed to
rain or moisture, does not operate normally, or has been dropped.
15. Batteries shall not be exposed to excessive heat such as sunshine, fire or
the like.
CAUTION:
•The ventilation should not be impeded by covering the ventilation
openings with items, such as newspapers, tablecloths, curtains,
etc.
•No naked flame sources, such as lighted candles, should be
placed on the unit.
•Observe and follow local regulations regarding battery disposal.
•Do not expose the unit to dripping or splashing fluids.
•Do not place objects filled with liquids, such as vases, on the
unit.
ATTENTION:
•La ventilation ne doit pas être gênée en recouvrant les ouvertures
de la ventilation avec des objets tels que journaux, rideaux, tissus,
etc.
•Aucune flamme nue, par exemple une bougie, ne doit être placée
sur l’appareil.
•Veillez à respecter les lois en vigueur lorsque vous jetez les piles
usagées.
•L’appareil ne doit pas être exposé à l’eau ou à l’humidité.
•Ne pas poser d’objet contenant du liquide, par exemple un vase,
sur l’appareil.
CAUTION:
To completely disconnect this product from the mains, disconnect
the plug from the wall socket outlet.
The mains plug is used to completely interrupt the power supply to
the unit and must be within easy access by the user.
PRECAUTION:
Pour déconnecter complètement ce produit du courant secteur,
débranchez la prise de la prise murale.
La prise secteur est utilisée pour couper complètement
l’alimentation de l’appareil et l’utilisateur doit pouvoir y accéder
facilement.
FRANCAIS ENGLISH
FCC INFORMATION (For US customers)
nNOTE ON USE / OBSERVATIONS RELATIVES A L’UTILISATION
1. PRODUCT
This product complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this
product may not cause harmful interference, and (2) this product must accept any interference received, including
interference that may cause undesired operation.
2. IMPORTANT NOTICE: DO NOT MODIFY THIS PRODUCT
This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements.
Modification not expressly approved by DENON may void your authority, granted by the FCC, to use the product.
3. NOTE
This product has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation.
This product generates, uses and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this product does cause harmful interference to radio or
television reception, which can be determined by turning the product OFF and ON, the user is encouraged to try to
correct the interference by one or more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the product into an outlet on a circuit different from that to which the receiver is connected.
•Consult the local retailer authorized to distribute this type of product or an experienced radio/TV technician for
help.
• Keep the unit free from moisture, water,
and dust.
• Protéger l’appareil contre l’humidité, l’eau
et la poussière.
• Do not let foreign objects into the unit.
• Ne pas laisser des objets étrangers dans
l’appareil.
• Avoid high temperatures.
Allow for sufficient heat dispersion when
installed in a rack.
• Eviter des températures élevées.
Tenir compte d’une dispersion de chaleur
suffisante lors de l’installation sur une
étagère.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
• Do not let insecticides, benzene, and
thinner come in contact with the unit.
• Unplug the power cord when not using the • Ne pas mettre en contact des insecticides,
du benzène et un diluant avec l’appareil.
unit for long periods of time.
• Débrancher le cordon d’alimentation
lorsque l’appareil n’est pas utilisé pendant
de longues périodes.
• Handle the power cord carefully.
Hold the plug when unplugging the cord.
• Manipuler le cordon d’alimentation avec
précaution.
Tenir la prise lors du débranchement du
cordon.
* (For apparatuses with ventilation holes)
• Do not obstruct the ventilation holes.
• Ne pas obstruer les trous d’aération.
• Never disassemble or modify the unit in
any way.
• Ne jamais démonter ou modifier l’appareil
d’une manière ou d’une autre.
II
ENGLISH
n Contents
Getting Started
Flow of operations through playback··········································2
Accessories···················································································2
Cautions on Handling····································································3
Cautions on Installation································································3
About the Remote Control Unit···················································3
Inserting the Batteries···································································3
Operating Range of the Remote Control Unit·······························3
Part Names and Functions····························································4
Front Panel·····················································································4
Display···························································································5
Rear Panel······················································································6
Remote Control Unit······································································7
Connections
Important Information···································································8
Cables Used for Connections························································8
Converting Input video signals for Output (Video Conversion
Function)························································································9
How the on-screen display is displayed depending on the video
input signal····················································································9
Installing/Setting the Speakers·················································· 10
Connecting the Speakers···························································· 11
Connecting Devices····································································· 12
Connecting Devices not Equipped with HDMI connectors······ 13
Once Connections are Completed·············································· 16
Turning the Power On·································································· 16
Turning the Power Off·································································· 16
Settings
Menu map····················································································· 17
Examples of On-screen Display and Front Display··················· 18
Making the Optimum Settings for the Connected Speakers
Automatically (Audyssey Auto Setup)······································· 19
Making detailed settings (Manual Setup)·································24
Making the input settings (Input Setup)···································30
Playback
Playing Components····································································34
Playing Blu-ray Disc / DVD Players···············································34
iPod® Playback············································································34
Listening to FM/AM Broadcasts··················································36
Operations During Playback·························································37
Selecting the Surround Mode·····················································37
q Playing sources according to the sources’ audio signal format/
number of channels (Standard Playback)·····································37
w Playing in a DENON original surround mode···························38
e Direct Playback········································································38
r Stereo Playback·······································································39
Adjusting the Sound Field Effects (Parameter)·························39
Adjusting the sound field effects (Surround Parameter)··············39
Adjusting the tone (Tone Control)················································41
Making the MultEQ, Dynamic EQ and Dynamic Volume settings
(Audyssey Settings)·····································································41
Adjust tonal quality for each speaker using graphic equalizer
(Manual EQ)·················································································42
Restoring compressed audio to nearly pre-compressed conditions
for playback (RESTORER)····························································43
Adjusting the audio delay time while watching the picture (Audio
Delay)···························································································43
Checking the Status (Information)······························43
Convenient functions
HDMI Control Function································································44
Setting the power to standby after a certain amount of time
(Sleep Timer Function)································································44
Playing the picture of a different input source without changing
the currently playing sound (Video Select Function)···············44
Adjust the volume of the different speakers·····························45
Saving frequently used settings (Quick Select Function)········45
Various memory functions··························································45
Operating the Connected Devices by Remote
Control Unit
Registering Preset Codes····························································46
Operating Registered Devices····················································46
Assigning buttons that are Not Used to Operate Other Devices
(Punch Through Function)···························································48
Other Information································································49
Troubleshooting···································································55
Restoring all the settings to as they were at the time of
purchase (Resetting the Microprocessor)··································57
Specifications·········································································58
List of preset codes···································End of this manual
ENGLISH
Thank you for purchasing this DENON product. To ensure proper
operation, please read this owner’s manual carefully before using the
product.
After reading them, be sure to keep them for future reference.
Connections
Flow of operations through
playback
Getting Started
Getting Started
Perform the operations leading to playback on the AVR-590 in the
order shown below.
Accessories
Settings
Connections
Check that the following parts are supplied with the product.
Installing/Setting the Speakers (vpage 10)
Connecting the Speakers (vpage 11)
Connecting Devices (vpage 12)
⇩
Turning the Power On (vpage 16)
Remote Control
⇩
qOwner’s manual....................................................................... 1
wGetting Started......................................................................... 1
eWarranty (for North America model only)................................. 1
rService station list.................................................................... 1
tRemote control (RC-1120)......................................................... 1
yR03/AAA batteries.................................................................... 2
uFM indoor antenna................................................................... 1
iAM loop antenna...................................................................... 1
oSetup microphone
Playback
⇩
(DM-A409, Cord length: Approx. 25 ft / 7.6 m).......................... 1
u
i
Information
t
o
Troubleshooting
Settings
Audyssey Auto Setup (vpage 19)
Manual Setup (vpage 24)
Specifications
b Perform “Manual Setup” as necessary.
Input Setup (vpage 30)
Playback
Playing Components (vpage 34)
⇩
Selecting the Surround Mode (vpage 37)
⇩
Adjusting the Sound Field Effects (vpage 39)
ENGLISH
Getting Started
Cautions on Handling
•Before turning the power switch on
Check once again that all connections are correct and that there are
no problems with the connection cables.
Note:
For proper heat dispersal, do not install this unit in a confined
space, such as a bookcase or similar enclosure.
Connections
•Power is supplied to some of the circuitry even when the unit is
set to the standby mode. When traveling or leaving home for long
periods of time, be sure to unplug the power cord from the power
outlet.
bNote
b
Settings
Playback
•About condensation
If there is a major difference in temperature between the inside of
the unit and the surroundings, condensation (dew) may form on
the operating parts inside the unit, causing the unit not to operate
properly.
If this happens, let the unit sit for an hour or two with the power
turned off and wait until there is little difference in temperature
before using the unit.
Remote Control
•Cautions on using mobile phones
Using a mobile phone near this unit may result in noise. If so, move
the mobile phone away from this unit when it is in use.
Information
•Moving the unit
Turn off the power and unplug the power cord from the power
outlet.
Next, disconnect the connection cables to other system units before
moving the unit.
•Note that the illustrations in these instructions may differ from the
actual unit for explanation purposes.
NOTE
Cautions on Installation
b
b
Wall
About the Remote Control Unit
In addition to the AVR-590, the included remote control unit (RC1120) can also be used to operate the equipment listed below.
qDENON system components
wNon-DENON system components
•By setting the preset memory (vpage 46)
•Replace the batteries with new ones if the set does not operate even
when the remote control unit is operated close to the unit.
•The supplied batteries are only for verifying operation.
•When inserting the batteries, be sure to do so in the proper direction,
following the “q” and “w” marks in the battery compartment.
•To prevent damage or leakage of battery fluid:
•Do not use a new battery together with an old one.
•Do not use two different types of batteries.
•Do not attempt to charge dry batteries.
•Do not short-circuit, disassemble, heat or dispose of batteries in
flames.
•If the battery fluid should leak, carefully wipe the fluid off the inside
of the battery compartment and insert new batteries.
•Remove the batteries from the remote control unit if it will not be in
use for long periods.
•Used batteries should be disposed of in accordance with the local
regulations regarding battery disposal.
Operating Range of the Remote Control
Unit
Point the remote control unit at the remote sensor when operating it.
Troubleshooting
Inserting the Batteries
30°
qLift the clasp and remove the wLoad the two batteries properly
rear cover.
30°
Specifications
as indicated by the marks in
the battery compartment.
R03/AAA
Approx. 23 feet / 7 m
NOTE
The set may function improperly or the remote control unit may not
operate if the remote control sensor is exposed to direct sunlight,
strong artificial light from an inverter type fluorescent lamp or infrared
light.
ePut the rear cover back on.
ENGLISH
Getting Started
Part Names and Functions
Front Panel
W7
W8
W6
Button that function in the same way as remote control buttons
W5 W4
o
i
For buttons not explained here, see the page indicated in parentheses ( ).
qPower operation button
(ON/STANDBY)··········································· (16)
r t
y
u
W2
W3
Buttons, connectors and displays only provided on the main unit
Q2
Q0
Q1
Q4
Q6
Q5
e
r
i
t
y
Specifications
W5HD AUDIO indicator····································· (38)
W6MASTER VOLUME indicator
W7Display
W8Remote control sensor·································· (3)
W9TUNING PRESET button····························· (36)
E0SOURCE MODE SELECT button················ (34)
o
Troubleshooting
Q9Power indicator··········································· (16)
W0Power switch (hON jOFF)················ (16, 57)
W1Headphones jack (PHONES)······················· (37)
W2V. AUX INPUT connectors·························· (15)
W3SETUP MIC jack··········································· (20)
W4AUDYSSEY DYNAMIC VOLUME
u
Information
e
W1
Q6 Q7 Q8
Remote Control
w
Q9 W0
Q4 Q5
q
Playback
q
Q3
way as Front Panel buttons
Settings
Q0 Q1 Q2
wSURROUND MODE buttons······················· (37)
eMENU button··············································· (17)
rCursor buttons (uio p)·························· (17)
tENTER button·············································· (17)
yRETURN button··········································· (17)
uQUICK SELECT buttons······························ (45)
iMASTER VOLUME control knob················ (34)
oSOURCE SELECT knob······························· (34)
Q0VIDEO SELECT button····························· (44)
Q1SLEEP TIMER button· ······························ (44)
Q2INPUT MODE button··································· (32)
Q3RESTORER button······································· (43)
Q4DYNAMIC EQ button··································· (42)
Q5DYNAMIC VOLUME button························ (42)
Q6MULTEQ button·········································· (41)
Q7DIMMER button··········································· (37)
Q8STATUS button············································ (43)
nButtons that function in the same
indicator······················································· (42)
Q7
Q8
w
Connections
W9
E0
Q3
ENGLISH
Getting Started
Part Names and Functions
Display
Q4
Q3
Q2
Q1 Q0
o
i u
y
Connections
Settings
q
w
Playback
q Decoder indicators
The indicator for the currently operating decoder
lights.
Remote Control
w Input audio signal indicators
e Information display
The input source name, surround mode, setting
values and other information are displayed
here.
e
r
o AUDYSSEY indicator
These light as shown below in the different
modes (vpage 41).
: During “MultEQ” operation
:D
uring “MultEQ” , “Dynamic EQ”
operation
r Front speaker indicator
Information
Lights when audio signals are being output
from the speakers.
t QUICK SELECT indicators
Troubleshooting
These light when the Quick Select function is
set (vpage 45).
y Master volume indicator
When performing setting operations, displays
the menu number.
u SLEEP TIMER indicator
Specifications
Lights when the sleep timer is operating
(vpage 44).
i MUTE indicator
Lights when the muting mode is set (vpage
37).
t
: During “MultEQ” , “Dynamic EQ”,
bWhen speaker settings are changed after the
“Dynamic Volume” operation
Audyssey Auto Setup procedure, either the
indicators’ frame turns off or all the indicators
turn off.
Q0 Input mode indicators
Q1 S.BACK indicator
Lights when surround back audio signals are
being output from the SURR. BACK / FRONT
HEIGHT PRE OUT connectors (vpage 25).
Q2 RESTORER indicator
Lights during “RESTORER” operation (vpage
43).
Q3 HDMI indicator
Lights when HDMI input signals are detected
(vpage 13).
Q4 Tuner reception mode indicators
This lights according to the reception conditions
when the input source is set to “TUNER”.
•AUTO
This lights when in the auto tuning mode.
•STEREO
In the FM mode, this lights when receiving
analog stereo broadcasts.
•TUNED
This lights when the broadcast is properly
tuned in.
ENGLISH
Rear Panel
Connections
i
Q1 Q0 o
Getting Started
Part Names and Functions
Settings
Playback
Remote Control
Information
e
r
t
y
u
qHDMI connectors······································································ (13)
tAnalog audio connectors························································· (14)
oCOMPONENT VIDEO connectors············································ (14)
wDigital audio connectors·························································· (14)
yFM/AM antenna terminals······················································· (16)
Q0Control Dock for iPod S-Video input connector···················· (14)
eVIDEO connectors···································································· (15)
uSpeaker terminals····································································· (11)
Q1Control Dock for iPod������������������
DOCK CONTROL jack·························· (14)
�����������������
rPRE OUT connectors································································ (11)
iPower cord················································································ (16)
Specifications
w
Troubleshooting
q
ENGLISH
Getting Started
Part Names and Functions
Remote Control Unit
q
Connections
w
e
Q5
Settings
Q6
r
Q7
Playback
Q8
Remote Control
t
y
u
i
Q9
W0
W1
W2
o
Information
Q0
Q1
Q2
W3
W4
Troubleshooting
Q3
Specifications
W5
W6
Q4
W8
qRemote control signal transmitter
wPower buttons·········································································· (16)
eQUICK SELECT buttons···························································(45)
rSOURCE SELECT buttons························································(34)
tVIDEO SELECT button·····························································(44)
yDYNAMIC VOLUME button·····················································(42)
uMULTEQ button·······································································(41)
iDYNAMIC EQ button································································(42)
oMENU button············································································ (17)
Q0Cursor buttons (uio p)······················································· (17)
Q1ENTER button··········································································· (17)
Q2SEARCH button········································································(35)
Q3System buttons········································································(46)
Q4Surround mode buttons··························································(37)
Q5TV POWER button····································································(47)
Q6TV INPUT button······································································(47)
Q7FRONT HEIGHT SPEAKER ON/OFF button····························(41)
Q8INPUT MODE button································································(32)
Q9SLEEP TIMER button································································(44)
W0Device select switch···························································(34, 46)
W1MUTING button········································································(37)
W2Channel level adjustment button···········································(45)
W3Master volume control buttons··············································(34)
W4RETURN button········································································ (17)
W5DIMMER button········································································(37)
W6STATUS button·········································································(43)
W7RESTORER button····································································(43)
W8Number buttons (0 ~ 9)····························································(46)
W7
n Operations on the AVR-590
n Operations on six devices other that the AVR-590
Preset the remote control codes of the devices to be operated
beforehand (vpage 46).
qSwitch the DEVICE SELECT switch according to the device to be
operated.
wPress the SOURCE SELECT button for the device to be
operated.
b For detailed operating instructions, see “Operating registered
devices” (vpage 46).
q
w
DEVICE SELECT
switch
SOURCE
SELECT
button
TUNER/AMP
−
Operable devices
AVR-590 and Tuner
DVD Player or CD player
Blu-ray disc player
iPod (DENON)
DEVICE
Digital video recorder
Video deck
Satellite receiver or Cable TV
TV
For buttons not explained here, see the page indicated in parentheses
( ).
Operations possible by remote control
TV
n Punch through setting (vpage 48)
ENGLISH
n Connection Flow
Connections for all compatible audio and video signal formats
are described in this owner’s manual. Please select the types of
connections suited for the equipment you are connecting.
After connections are completed, certain settings must be made on
the receiver. Make the settings indicated “ Set as necessary ”
for the individual items.
NOTE
nSAT/CABLE Tuner (vpage 14)
nRecording Components
Coaxial digital
connections
Coaxial digital cable
Optical digital
connections
Analog
connections
Optical cable
(White)
L
L
(Red)
R
R
Stereo pin-plug cable
Analog
connections
(monaural, for
subwoofer)
Pin-plug cable
Speaker
connections
•DVD Recorder (vpage 15)
•Video Cassette Recorder (vpage 15)
•Video Camera / Game Console (vpage 15)
•Antenna terminals (vpage 16)
Speaker cables
Video cables
Component
video
connections
nPower Cord
Specifications
nOther Devices
Troubleshooting
•Blu-ray Disc player / DVD player (vpage 14)
•iPod® (vpage 14)
HDMI cable
Audio cables
Information
nHDMI (vpage 12)
nMonitor (TV) (vpage 13)
nPlayback Components
Audio and video cables
HDMI
connections
Remote Control
Connecting Devices not Equipped with HDMI
connectors (vpage 13)
Select the cables according to the equipment being connected.
Playback
Connecting Devices (vpage 12)
•Do not plug in the power cord until all connections have been
completed.
•When making connections, also refer to the operating instructions
of the other components.
•Be sure to connect the left and right channels properly (left with left,
right with right).
•Do not bundle power cords together with connection cables. Doing
so can result in humming or noise.
Cables Used for Connections
Settings
Connecting the Speakers (vpage 11)
Important Information
Connections
Installing/Setting the Speakers (vpage 10)
Getting Started
Connections
(Green)
(Blue)
(Red)
Component video cable
S-Video
connections
Turning the Power On (vpage 16)
S-Video cable
Video
connections
(Yellow)
75 Ω/ohms pin-plug video cable
ENGLISH
Getting Started
Important Information
Converting Input video signals for Output
(Video Conversion Function)
How the on-screen display is displayed depending on the
video input signal
Connections
Settings
The AVR-590 is equipped with four types of video input connectors (HDMI, Component video, S-Video and
video) and three types of video output connectors (HDMI, Component video and video).
Use the connectors according to the devices to be connected.
This function automatically converts various formats of video signals input to the AVR-590 into the format
used to output the video signals from the AVR-590 to a monitor.
AVR-590
Monitor (TV)
Video devices
Playback
Remote Control
Output
Input
(IN)
Information
HDMI connector
HDMI connector
Component video
connectors
Component video
connectors
Output
(MONITOR OUT)
HDMI
connector
Component video
connectors
The way the on-screen display of the menus, status, etc., is displayed differs according to the type of video
signal input to the AVR-590.
When video signals are input from the HDMI or component video connectors
• Menu: Switches to a screen with a black background and the menu is superimposed. (b)
• Status display: Not displayed.
b:If you want to display the menus superimposed on the picture being played, input the same video
signals to the S-Video or video connectors. When a menu is displayed, the picture switches to the one
being input from the S-Video or video connectors and the menu is displayed superimposed over this
picture.
Input
NOTE
Menus and status display screens are not displayed for component video connector pictures. To
display them, also connect the video connectors.
HDMI connector
Component video
connectors
When video signals are being input from the S-Video or video connectors
• Menu: Menus are displayed superimposed over the picture being played.
• Status display: Displayed.
n Examples of on-screen display
Troubleshooting
S-Video connector
S-Video
connector
Video connector
Video connector
• Menu screen
Video connector
Video connector
Specifications
The video conversion function supports the NTSC, PAL, SECAM, NTSC 4.43, PAL-N, PAL-M and PAL-60
formats.
NOTE
•The S-Video input connector is exclusively for use with a Control Dock for iPod. It can be used when the
Control Dock for iPod is connected to the connector assigned to the iPod input source.
•HDMI signals cannot be converted into analog signals.
•When a non-standard video signal from a game machine or some other source is input, the video
conversion function might not operate.
• Status display screen
When the input source is
switched
When the volume is adjusted
MENU
1.Parameter
2.Information
3.Auto Setup
4.Manual Setup
5.Input Setup
[ENT]:Select
[Auto]
IN :DVD
MODE:STEREO
Master Volume -80.0dB
Status display: The operating status is displayed temporarily on the
screen when the input source is switched or the
volume is adjusted.
ENGLISH
n When 7.1ch (Surround Back Speaker) Connected
Front speakers
2
z1
z4
z5
Surround speakers
Front
speaker
Surround back speakers
•It is not possible to use the front height speakers and
surround back speakers simultaneously.
•To play surround back speakers or front height speakers,
connect a power amplifier to the AVR-590’s SURR. BACK /
FRONT HEIGHT PRE OUT connectors (vpage 11).
3
Surround speakers
Subwoofer
Surround
Surround back
speaker
speaker
Front
speaker
2 to 3 feet /
60 to 90 cm Point slightly
downwards
Surround back
speaker
GAs seen from aboveH
GAs seen from the sideH
4
2
Center speaker
z2
z1
Monitor
z
3
z1:30˚
z2:45˚
z3:90˚
z4:110˚
Point slightly
downwards
Front height
speaker
Front speaker
Surround
speaker
2 to 3 feet /
60 to 90 cm
Specifications
NOTE
z
z
Front height speakers
Front speakers
z1:22 ~ 30˚
z2:90˚
z3:110˚
Surround speakers
GAs seen from aboveH
Troubleshooting
Surround
speaker
n When 7.1ch (Front Height Speaker) Connected
z
z1
GAs seen from the sideH
Information
Subwoofer
Remote Control
Center
speaker
GAs seen from aboveH
Front speakers
Center speaker
Monitor
2 to 3 feet /
60 to 90 cm
Surround speakers
GAs seen from the sideH
n When 6.1ch Connected
Surround
speaker
Playback
Surround
Surround back
speaker
speaker
Front
speaker
2 to 3 feet /
60 to 90 cm Point slightly
downwards
GAs seen from aboveH
Front
speakers
Surround
speaker
Subwoofer
3
Surround back
speakers
Front Height speakers
Subwoofer
z
z1:22 ~ 30˚
z2:120˚
Settings
aDetermine the Speaker Layout.
z
Front speakers
Center speaker
Monitor
z4:30˚
z5:45˚
z2
z1
Installing All the Speakers
z1:22 ~ 30˚
z2:90˚
z3:110˚
Center speaker
Monitor
Subwoofer
Below we introduce examples of speaker layouts. Refer
to these to arrange your speakers according to their
type and how you want to use them.
n When 5.1ch Connected
Connections
•The AVR-590 is compatible with various types of
surround playback.
• Decide on the surround modes to be played on
the AVR-590 before making connections and
settings.
Getting Started
Installing/Setting the Speakers
GAs seen from the sideH
10
ENGLISH
Getting Started
Installing/Setting the Speakers
sSet the “Pre Assign” Mode According to the Speaker Layout.
The signals output from the AVR-590’s SURR. BACK / FRONT HEIGHT PRE OUT connectors can be
switched to signals of the surround mode being used (vpage 24 “Pre Assign”).
Connections
Pre Assign mode
(vpage 24)
Connecting the Speakers
Subwoofer with
builtin amplifier
Front
speakers
The speaker which plays the a
sound output from the SURR.
Example of speaker installation
BACK / FRONT HEIGHT PRE
OUT connectors
(L)
Settings
w
Center
speaker
w
(R)
q
w
q
q
Normal
(L)
w
*/
Playback
(Default)
Surround
speakers
(R)
qw
q
Surround back
speakers
(7.1)
Remote Control
Surround back
speakers
Normal
Information
bConnect to the SURR. BACK /
FRONT HEIGHT PRE OUT “L”
connector.
bSet “S.Back (Pre out)” (vpage
25) to “1ch”.
(6.1)
Not connected
L
bSet the “��������������������������
S.Back (Pre out)����������
” setting
(vpage 25) to “None”.
(5.1)
Power amplifier
To play surround back speakers or front height speakers,
connect a power amplifier to the AVR-590’s SURR. BACK /
FRONT HEIGHT PRE OUT connectors.
Make the “Pre Assign” (vpage 24) settings.
R
Troubleshooting
Normal
R
L
Specifications
Front Height
Front Height
speakers
w
q
w
q
(7.1)
(L)
11
(R)
Front Height
speakers
or
Surround back
speakers
ENGLISH
1
Peel off about 10 mm of sheathing from the tip
of the speaker cable, then either twist the core
wire tightly or terminate it.
2
3
4
Turn the speaker terminal counterclockwise
to loosen it.
Insert the speaker cable’s core wire to the hilt
into the speaker terminal.
Turn the speaker terminal clockwise to tighten
it.
n When using a banana plug
Important Information
n About HDMI
“HDMI” is the abbreviation of “High Definition Multimedia
Interface”. This interface allows transfer of digital video signals
and digital audio signals over a single HDMI cable.
“HDMI”, “HDMI logo” and “High-Definition Multimedia Interface”
are trademarks or registered trademarks of HDMI Licensing LLC.
n Functions usable with HDMI connections
Deep Color
Eliminates on-screen color banding, for smooth tonal transitions and
subtle gradations between colors.
x.v.Color
Enables displays with natural, vivid colors. “x.v.Color” is a Sony
registered trademark.
Auto Lip Sync (vpage 27)
Use speakers with an impedance of 6 to 16 Ω/ohms.
HDMI control function (vpage 27, 44)
This function allows you to operate external devices from the receiver
and operate the receiver from external devices.
n Copyright protection system (HDCP)
The AVR-590 supports HDCP (High-bandwidth Digital Contents
Protection). HDCP is a copyright protection technology for digital video
signals. The devices connected to the AVR-590 must also support
HDCP.
NOTE
When a device that does not support HDCP is connected, video
signals are not properly output.
12
Specifications
NOTE
These functions will not work if the device connected to the HDMI
connector does not support Deep Color or x.v.Color signal transfer or
the Auto Lip Sync function.
Troubleshooting
NOTE
•Connect the speaker cables in such a way that they do not stick out
of the speaker terminals. The protection circuit may be activated if
the core wires touch the rear panel or if the + and – sides touch each
other (v “Protection circuit”).
•Never touch the speaker terminals while the power
supply is connected. Doing so could result in electric shock.
HDMI 1.3 incorporates an automatic video/audio synching capability
that allows devices to perform this synchronization automatically with
total accuracy.
Information
Tighten the speaker terminal firmly before
inserting the banana plug.
Connecting Devices Equipped with
HDMI connectors
Remote Control
If the core wires touch the rear panel and the screws etc., or the ±
sides touch each other, the protection circuit will be activated and the
power indicator will flash red at intervals of 0.5 secs.
If the protection circuit is activated, the speaker output is isolated, and
the power supply goes to the standby state. If the power supply is
turned off, after the power supply cord is withdrawn, please confirm
that speaker cable and input cable are connected.
Also, if replaying large sound levels by using a speaker having an
impedance less than that specified (eg, 4 Ω/ohms), the temperature
will rise, and the protection circuit might be activated. The power
supply will go into the standby state, and the power indicator will flash
red at 2 second intervals.
In this case, please switch off the power supply, and wait until the
AVR-590 has cooled down, and the surrounding ventilation is good.
Even if there are no problems with the surrounding ventilation
and connections, in the event of the protection circuit becoming
activated,
due to thinking that the AVR-590 has failed, please contact DENON
Service center after switching off.
Playback
Carefully check the left (L) and right (R) channels and + (red) and –
(black) polarities on the speakers being connected to the AVR-590, and
be sure to interconnect the channels and polarities correctly.
Connecting Devices
Settings
Protection circuit
Connections
Connecting the Speaker Cables
Getting Started
Connecting the Speakers
ENGLISH
Getting Started
Connecting devices
Connections
The AVR-590 allows connection of inputs from up to 3 HDMI
devices and output to 1 TV.
Connections
DVD
Player
)%.*
065
Settings
Playback
Remote Control
Blu-ray
Disc Player
)%.*
065
SAT/CABLE
Tuner
)%.*
065
Monitor
(TV)
)%.*
*/
nConnecting to a device equipped with a DVI-D
connector
When an HDMI/DVI conversion cable (sold separately) is used, the
HDMI video signals are converted to DVI signals, allowing connection
to a device equipped with a DVI-D connector.
NOTE
•No sound is output when connected to a device equipped with a
DVI-D connector. Also make the audio connections.
•Signals cannot be output to DVI-D devices that do not support
HDCP.
•Depending on the combination of devices, the video signals may not
be output.
nSettings related to HDMI connections
Connecting Devices not
Equipped with HDMI connectors
Monitor (TV)
•Select the terminal to use and connect the device.
•For video connections, see “Converting input video signals for output
(Video Conversion Function)” (vpage 9).
For instructions on HDMI connections, see “Connecting Devices
Equipped with HDMI connectors” on page 12.
Monitor (TV)
"6%*0
015*$"065
7*%&0
7*%&0
*/
$0.10/&/57*%&0
*/
:
1# 13
Set as necessary. For details, see the respective reference pages.
Input connector assignment (vpage 31)
Set this when changing the input sources of the different connectors.
HDMI Setup (vpage 27)
Information
Troubleshooting
Specifications
•Use a cable on which the HDMI logo is indicated (a certified HDMI
product) for connection to the HDMI connector. Normal playback
may not be possible when using a cable other than one on which the
HDMI logo is indicated (a non-HDMI-certified product).
•When the AVR-590 is connected to other devices with HDMI cables,
also connect the AVR-590 and TV using an HDMI cable.
•When a device supporting Deep Color signal transfer is connected,
use a cable compatible with HDMI ver.1.3a.
•Video signals are not output if the input video signals do not match
the monitor’s resolution. In this case, switch the Blu-ray Disc player /
DVD player’s resolution to a resolution with which the monitor is
compatible.
Make these settings related to HDMI input/output signals.
•Auto Lip Sync
•HDMI Audio Out
•HDMI Control
•Standby Source
•Power Off Control
NOTE
The audio signals output from the HDMI connectors are only the
HDMI input signals.
NOTE
•If the menu “HDMI Audio Out” setting (vpage 27) is set to “AMP”,
the sound may be interrupted when the monitor’s power is turned
off.
•The audio signal from the HDMI output connector (sampling
frequency, number of channels, etc.) may be limited by the HDMI
audio specifications of the connected device regarding permissible
inputs.
13
The component video connectors may be indicated differently on your
monitor. For details, see the monitor’s operating instructions.
ENGLISH
Playback Components
SAT/CABLE Tuner
Blu-ray Disc player / DVD player
Control dock for iPod®
Select the terminal to use and connect the device.
Use a DENON control dock for iPod (ASD-1R, ASD-11R, ASD-3N or
ASD-3W sold separately) to connect the iPod to the AVR-590. For
instructions on the control dock for iPod settings, refer to the control
dock for iPod’s operating instructions.
"6%*0
"6%*0
065
3
$0"9*"065
7*%&0
7*%&0
065
ASD-3N
or
ASD-3N または
ASD-3W
ASD-3W
L
R
L
R
Playback
7*%&0
"6%*0
065
3
Settings
Control dock for iPod
$0.10/&/57*%&0
065
:
1# 13
R
R
L
R
L
Remote Control
L
SAT/CABLE Tuner
"6%*0
Blu-ray Disc player /
DVD player
L
For instructions on HDMI connections, see “Connecting Devices
Equipped with HDMI connectors” on page 12.
Connections
For instructions on HDMI connections, see “Connecting Devices
Equipped with HDMI connectors” on page 12.
Select the terminal to use and connect the device.
Getting Started
Connecting Devices not Equipped with HDMI connectors
R
Information
Troubleshooting
Specifications
Set as necessary
Set as necessary
Set this to change the input signal to which the input source
is assigned.
“Assign” (vpage 31)
Set as necessary
Set this to change the input signal to which the input source
is assigned.
“Assign” (vpage 31)
Set this to assign the iPod to a connector other than “VCR
(iPod)” “iPod Dock” (vpage 31)
NOTE
When connected to a Blu-ray Disc player, and playing Dolby TrueHD,
DTS-HD, Dolby Digital Plus, connect the HDMI.
With the default settings, the iPod can be used connected to the VCR
(iPod) connector.
14
ENGLISH
Getting Started
Connecting Devices not Equipped with HDMI connectors
Recording Components
Other Devices
Video Camera / Game Console
Connections
Digital Video Recorder
Video Cassette Recorder
Select the terminal to use and connect the device.
Select the terminal to use and connect the device.
For instructions on HDMI connections, see “Connecting Devices
Equipped with HDMI connectors” on page 12.
For instructions on HDMI connections, see “Connecting
Devices Equipped with HDMI connectors” on page 12.
Settings
DVD Recorder
Video cassette recorder
7*%&0
Playback
$0.10/&/57*%&0
065
:
1# 13
"6%*0
7*%&0
065
015*$"065
"6%*0
065
3
7*%&0
"6%*0
"6%*0
7*%&0
"6%*0
7*%&0
*/
"6%*0
*/
3
"6%*0
*/
3
7*%&0
065
"6%*0
065
3
Remote Control
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
Information
Troubleshooting
Specifications
Set as necessary
Set this to change the input signal to which the input source
is assigned.
“Assign” (vpage 31)
NOTE
To record video signals through the AVR-590, use the same type of
video cable for connection between the AVR-590 and the player as the
cable used for connection between the AVR-590 and the recorder.
15
Set as necessary
Set this to change the input signal to which the input
source is assigned.
“Assign” (vpage 31)
NOTE
To record video signals through the AVR-590, use the same type
of video cable for connection between the AVR-590 and the
player as the cable used for connection between the AVR-590
and the recorder.
Video camera /
Game console
"6%*0
7*%&0
"6%*0
065
3
7*%&0
065
R
L
R
L
ENGLISH
nConnection of AM antennas
Direction of broadcasting station
1
2
FM antenna
Push the lever.
Turning the Power On
1
Insert the conductor.
75 Ω/ohms
Coaxial cable
FM indoor antenna
(supplied)
AM outdoor antenna
.
The power indicator flashes green and the
power turns on.
bAlso press
•Do not connect two FM antennas simultaneously.
•Even if an external AM antenna is used, do not disconnect the AM
loop antenna.
•Make sure the AM loop antenna lead terminals do not touch metal
parts of the panel.
nAM loop antenna assembly
when in
standby mode, the power turns on.
When
has been pressed, the input
source set with the
If a
Remove the vinyl tie and take out the
connection line.
Bend in the reverse direction.
in the memory for the quick select function is set (vpage 45
“Saving frequently used settings (Quick Select Function)”).
Connecting the Power Cord
Wait until all connections have been completed before connecting the
power cord.
To household
power outlet
(AC 120 V, 60 Hz)
With the antenna on top of any
stable surface.
Power cord
Mount
has been pressed, the input source stored
pressing a
Turning the Power Off
1
Press
Press
NOTE
Insert the AC plugs securely. Incomplete connections could cause
noise.
.
The power is set to the standby mode.
2
Installation hole Mount on wall, etc.
on the main unit.
Specifications
the antenna attached to a
3-2With
wall.
This operation can also be performed by
Troubleshooting
2
3-1
is set.
Information
1
Press
Remote Control
Ground
2
Return the lever.
NOTE
White
.
The power indicator lights red and the
power is set to the standby mode.
Playback
Black
3
Press
Settings
AM loop
antenna
(supplied)
Once Connections are
Completed
Connections
Antenna terminals
Getting Started
Connecting Devices not Equipped with HDMI connectors
.
The power indicator turns off, and so does
the power.
NOTE
Power continues to be supplied to some of the circuitry even when
the power is in the standby mode. When leaving home for long periods
of time or when traveling, either press
to turn off the power, or
unplug the power cord from the power outlet.
16
ENGLISH
With the AVR-590, settings and operations for most functions can be performed by operating while looking at the menus displayed on the monitor screen.
ress ui to
2Pselect
the item
.
The menu is
displayed.
Settings
you want to
set, then press
ress ui to
3Pselect
the item
you want to
set, then press
.
Playback
n Setting menus
MENU
Remote Control
1.Parameter
2.Information
3.Auto Setup
4.Manual Setup
5.Input Setup
Information
Troubleshooting
Set these for example upon purchase.
Once these items are set, there is no need to
set them again unless the speaker layout or the
connected speakers have been changed.
.
bSelect “Default Yes”, then press
reset to the default setting.
to
The settings made up to that
point are entered and the
settings menu screen turns off.
Number
Description
Page
1-1
1-2
1-3
1-4
1-5
1-6
2-1
2-2
2-3
Surround Parameter
Tone Control
Audyssey Settings
Manual EQ
RESTORER
Audio Delay
Status
Audio Input Signal
HDMI Information
Adjust surround sound parameters.
Adjusts the treble and bass tone.
Makes the MultEQ, Dynamic EQ and Dynamic Volume settings.
Adjust tonal quality for each speaker using graphic equalizer.
Uncompress compressed sources and apply bass boost for richer sound.
Compensate for incorrect timing between video and audio.
Shows information about current settings.
Shows information about audio input signals.
Displays the HDMI input/output signals and TV information.
39
41
41
42
43
43
43
43
43
2-4
2-5
2-6
3-1
Auto Surround Mode
Quick Select
Preset Channel
Audyssey Auto Setup
43
43
43
20
3-2
Parameter Check
4-1
4-2
4-3
4-4
5-1
5-2
5-3
5-4
5-5
5-1
5-2
5-3
Speaker Setup
HDMI Setup
Audio Setup
Option Setup
Assign
Input Mode
Rename
Source Level
iPod Playback Mode
Auto Preset
Preset Skip
Preset Name
Displays the settings stored for the auto surround mode.
Displays the settings stored for the Quick Select function.
Shows information about preset channels.
Makes the optimum settings for the speakers being used
automatically.
Check Audyssey Auto Setup measurement results.
This item is only displayed after the Audyssey Auto Setup procedure
has been performed.
Sets the speaker size and distance, the channel level, etc.
Make settings for HDMI video/audio output.
Make settings for audio playback.
Make various other settings.
Change input connector assignment.
Sets the audio input mode and decode mode.
Change the display name for this source.
Adjust the playback level of the audio input.
Make settings for iPod playback.
Use the auto preset function to program radio stations.
Set the preset memories that you do not want to display when tuning.
Assign name to a preset memory.
2. Information
Show information about receiver
settings, input signals, etc.
3. Auto Setup
Makes the optimum speaker
settings and corrects for the
acoustic characteristics of the
room.
Specifications
4. Manual Setup
Use this to make various types of
detailed settings.
Detailed items
.
Setting items
5. Input Setup
Use this to make settings related
to playing input sources.
17
.
bTo return to the previous item, press
5Press
1. Parameter
Adjust various audio parameters.
[ENT]:Select
Items that only need to be set once
se uiop to select the item,
4Uthen
press
to set.
⇩
1
Press
⇩
n Operations
⇩
Connections
Menu map
⇩
Getting Started
Settings
23
24
27
28
28
31
32
32
33
33
33
33
33
ENGLISH
Getting Started
Examples of On-screen Display and Front Display
Below we describe typical examples of displays on the TV screen and on the set’s display window.
On-screen Display
Front Display
Description
MENU
w 1.Parameter q
2.Information
3.Auto Setup
4.Manual Setup
5.Input Setup
e
q : The menu items are displayed here.
w : The selected line is displayed here.
q
q : The number of the current selected setting menu is
Parameter
The currently selected item is displayed on the display.
Use ui to move to the item you want to set.
e : The number of the current selected setting menu is
displayed.
Settings
w
e
Connections
n Top menu display
[ENT]:Select
Assign
q 5-1-1.Input
HDMI Digi Comp
1
2
w3
1
01
C1
DVD
02
e [ENT]:Select
w
made.
[RTN]:Back
Press
⇩
.
Press
.
Information
⇩
[HDMI1 ]
2
displayed.
w : Use uio p to move to the item you want to set.
e : Press
to set to the mode in which the setting can be
Remote Control
DVD
HDP
TV
SAT/CBL
VCR/iPod
DVR
Playback
n Display when changing settings
Assign
q 5-1-1.Input
HDMI Digi Comp
1
2
r3
1
DVD
01
C1
r : 0 1 is displayed at the sides of items whose setting can be
changed. Use o p to change to the desired setting.
•HDMI1 –
r
02
Troubleshooting
DVD
HDP
TV
SAT/CBL
VCR/iPod
DVR
2
[ENT]:Select [RTN]:Back
n Display when inputting characters
e 5-3.Rename
Default
q : When o p is pressed, the cursor moves to the left or right.
w : When ui is pressed at the position at which you want to
DVD
:
DVD
w
•¡
DVD
–
e
q
Specifications
DVD
q
input the character, the character is input.
e : The number of the current selected setting menu is
displayed.
[SRCH]:Caps.
[ENT]:OK
[RTN]:Cancel
n Display when resetting
w
5-3.Rename
Default
DVD
:[
DVD
]
q
w
q Default
[ ]:Up/Down
[ENT]:Select [RTN]:Back
q : Press i to select “Default”, then press
to set.
w : The number of the current selected setting menu is
displayed.
Default? : • No
w
18
ENGLISH
Getting Started
Making the Optimum Settings for the Connected Speakers Automatically (Audyssey Auto Setup)
The acoustic characteristics of the connected speakers and listening room are measured and the optimum settings are made automatically.
Connections
n Audyssey Auto Setup Flow
Step 1 :Connect the included Setup
Microphone (vpage 20)
Settings
Playback
Step 2 :Audyssey Auto Setup Preparations
(vpage 21)
Remote Control
nChanging the PRE OUT connectors assignment
(Pre Assign) (vpage 21)
Information
Step 3 : Performing the Audyssey Auto Setup
Procedure (vpage 21)
Important Information
Audyssey MultEQ® automatically measures the acoustical
problems in the listening environment to create the best audio
experience for your home theater.
•When the Audyssey Auto Setup procedure is performed, the
MultEQ, Dynamic EQ and Dynamic Volume functions (vpage 41)
are enabled.
•Use the included setup microphone (DM-A409) to perform the
Audyssey Auto Setup procedure.
•Measurements are performed by placing the calibrated microphone
successively at multiple positions throughout the listening area as
shown in GExample qH. For best results, it is strongly recommended
to measure 6 positions so that the measurements have the proper
spatial weighting.
Even if the listening environment is small as shown in GExample wH,
measuring at multiple points throughout the listening environment
results in more effective correction.
n When using Front Height Speakers
GExample qH
FHL
FL
SW
C
FR
GExample wH
FHR
FHL
FL
SW
C
FR
About the main listening position (*M)
The main listening position refers to the most central position where
one would normally sit within the listening environment.
MultEQ uses the measurements from this position to calculate
speaker distance, level, polarity, and the optimum crossover value
for the subwoofer.
FHR
NOTE
nCheck Audyssey Auto Setup Measurement
Troubleshooting
Results (Parameter Check) (vpage 23)
( : Measuring positions)
*M
*M
Specifications
SL
SR
SL
SR
n When using Surround Back Speakers
GExample qH
FL
SW
C
GExample wH
FR
FL
SW
C
FR
( : Measuring positions)
SL
SR
SL
SR
*M
*M
19
FHL : Front height speaker (L)
FL : Front speaker (L)
SW : Subwoofer
C : Center speaker
FR : Front speaker (R)
FHR : Front height speaker (R)
SR : Surround speaker (R)
SBR : Surround back speaker (R)
SBL : Surround back speaker (L)
SL : Surround speaker (L)
SBL
SBR
SBL
SBR
•Loud test sounds may be played during Audyssey MultEQ automatic
speaker setup. This is part of normal operation. If there is background
noise in room, these test signals will increase in volume.
•Do not stand between the speakers and setup microphone or allow
obstacles in the path while the measurements are being made. This
will cause inaccurate readings.
•Make the room as quiet as possible. Background noise can disrupt
the room measurements. Close windows, silence cell phones,
televisions, radios, air conditioners, fluorescent lights, home
appliances, light dimmers, or other devices as measurements may
be affected by these sounds.
Cell phones should be placed away from all audio electronics during
the measurement process as Radio Frequency Interference (RFI)
may cause measurement disruptions (even if the cell phone is not in
use).
ENGLISH
Step 1 : Connect the included Setup Microphone
NOTE
NOTE
(vpage 11 “Connecting the Speakers”)
When using a subwoofer, make the following settings before starting
the Audyssey Auto Setup procedure:
Set the TV’s input to the AVR-590.
n When using a subwoofer with a direct mode
(vpage 16 “Turning the Power On”)
n When using a subwoofer without a direct mode
Set the direct mode to “On” and disable the volume adjustment
and crossover frequency setting.
Make the following settings:
•Volume
:“12 o’clock position”
•Crossover frequency :“Maximum/Highest Frequency”
•Low pass filter
:“Off”
•Standby mode
:“Off”
Information
Remote Control
The Audyssey Auto Setup screen appears automatically.
Playback
When using a subwoofer on which the volume can
be adjusted and the crossover frequency can be set
Settings
1 Check the speaker connections.
2 Turn on the power of the TV and subwoofer.
3 Turn on the AVR-590’s power.
the included calibrated setup microphone to
4 Connect
the SETUP MIC jack on the main unit.
•Do not hold the microphone in your hand during measurements.
•Avoid placing the microphone close to a seat back or wall as sound
reflections may give inaccurate results.
Connections
•Do not disconnect the setup microphone until the Audyssey Auto
Setup procedure is completed.
•When using headphones, unplug the headphones before starting
the Audyssey Auto Setup procedure.
Sound
receptor
Troubleshooting
the setup microphone on a tripod or stand and
5 Mount
install it at the main listening position.
When installing the setup microphone, adjust its height so that
the section where the sound is received is at the height of the
ears during listening.
Specifications
Getting Started
Making the Optimum Settings for the Connected Speakers Automatically (Audyssey Auto Setup)
Setup
microphone
20
ENGLISH
Getting Started
Making the Optimum Settings for the Connected Speakers Automatically (Audyssey Auto Setup)
Step 2 : Audyssey Auto Setup
Preparations
around items indicate the settings made upon purchase.
Connections
If adjustment to the environment is necessary, set the following
items before proceeding.
Settings
Changing the PRE OUT connectors assignment
(Pre Assign)
Playback
The signals output from the AVR-590’s SURR. BACK / FRONT HEIGHT
PRE OUT connectors can be switched to signals of the surround mode
being used.
Remote Control
1 Press ui to select “Pre Assign”.
o p to select
2 Press
Pre Assign Mode.
Step 3 : Performing the Audyssey Auto Setup Procedure
•The Audyssey Auto Setup function detects the presence of each
speaker and automatically calculates the speaker size, channel
level, distance, and optimal crossover frequency setting. Audyssey
MultEQ corrects acoustical distortions within the listening area.
•Once started, MultEQ will play a series of test tones through each
speaker.
•Before starting, connect and position all of your speakers.
ui to select
1 Press
“Start”, then press
.
Detection of the speaker
configuration starts.
Information
3-1.Audyssey Auto Setup
MultEQ
Please place microphone
at ear height at
main listening position.
all the speakers
2 Once
have been detected
Troubleshooting
and the screen on
the right appears,
check the results
of detection of the
connected speakers.
Pre Assign:
Normal
Start
Cancel
[ENT]:Select [RTN]:Back
Specifications
Normal
:The sound of the surround back channel is output
from the SURR. BACK / FRONT HEIGHT PRE
OUT connectors.
Front Height
:The sound of the front height channel is output
from the SURR. BACK / FRONT HEIGHT PRE
OUT connectors.
n To cancel Audyssey Auto Setup
Use ui to select “Cancel”, then use o p to select “Yes”.
3-1.Audyssey Auto Setup
MultEQ
Please place microphone
at ear height at
main listening position.
Pre Assign:
Normal
Start
Cancel
[ENT]:Select [RTN]:Back
Step1:Speaker Detection
MultEQ
Front Sp.
:Yes
Center Sp.
:Yes
Subwoofer
:Yes
Surround Sp.
:Yes
S.Back Sp.
:Yes
:2sp
Next
Retry
[ENT]:Next
you have checked the results, use ui to select
3 Once
“Next”, then press
.
Measurements for the main listening position begin.
the screen on
4 Once
the right appears,
Step2:Measurement
move
the
setup
microphone to the
second position, use
ui to select “Next”,
then press
.
Next
Calculate
Cancel
MultEQ
Please place microphone
at ear height at
2nd listening position.
[ENT]:Next
Measurements for the second position begin.
21
Step 4 repeatedly for the 3rd, 4th, 5th, and
5 Perform
6th measurments.
Once measurements for the sixth position are completed, “All
the measurements were finished.” is displayed.
bMeasure at a total of six positions, including the main listening
position and positions around it. It is possible to stop the settings
with five positions or fewer, but for better results we recommend
measuring at six positions.
6
Once measurements
are finished, use ui
to select “Calculate”,
then press
.
Analysis begins.
b Analysis
takes several
minutes
to
complete.
The time required for
this analysis depends on
the number of speakers
connected. The greater
the number of speakers
connected, the longer
analysis will take.
Step2:Measurement
MultEQ
All the measurements
were finished.
Calculate
Retry
Cancel
[ENT]:Cancel
⇩
Step3:Calculating
MultEQ
Calculating
Please wait...
[----------]
ui to select the item you want to check, then
7 Use
press
.
The measurement result
confirmation screen is
displayed.
b Subwoofers
or
other
speakers may be set to
a value that does not
correspond to the actual
distance.
Step4:Check
MultEQ
Please check the results
of the measured item.
Speaker Config.Check
Distance Check
Channel Level Check
Crossover Freq.Check
Next
[ENT]:Select
ENGLISH
8 Press
NOTE
.
Store
Cancel
[ENT]:Store
⇩
Step5:Store
Storing
Please wait...
to repeat the measurement.
•If the result still differs from the actual connection status after remeasurement or the error message still appears, it is possible that
the speakers are not connected properly. Turn the AVR-590 off, check
the speaker connections and repeat the measurement process from
the beginning.
•For instance, If the location or direction of a speaker is altered, the
Audyssey Auto Setup should be performed again to ensure the correct EQ solution for the new room configuration.
MultEQ
Information
the measurement results,
use ui to select “Cancel”,
then select “Yes” using
o p. All the measured
Audyssey Auto Setup data
will be erased.
MultEQ
Please select “Store”
to store measurement
values.
Remote Control
b If you do not want to save
Step5:Store
Playback
“Storing Please wait...”
is displayed on the onscreen display while the
results are being stored.
When storing is complete,
“Storing complete. Auto
Setup is now finished.”
is displayed on the onscreen display.
•If the result differs from the actual connection status or an error message appears, use ui to on-screen display “Retry” and then press
.
Settings
i to select “Next”, then
9 Press
press
.
10Press ui to select “Store”, then press
Connections
Do not change the speaker connections or subwoofer volume, or
speaker locations after making measurements. If changes are necessary, make the changes and use the Audyssey Auto Setup once again
for an updated EQ solution.
This returns you to analysis results items,
so repeat step 7.
Getting Started
Making the Optimum Settings for the Connected Speakers Automatically (Audyssey Auto Setup)
NOTE
Troubleshooting
Do not turn the power off while the settings are being stored.
the setup microphone from the AVR12Disconnect
590.
Specifications
22
ENGLISH
Getting Started
Making the Optimum Settings for the Connected Speakers Automatically (Audyssey Auto Setup)
Error Messages
If the Audyssey Auto Setup procedure could not be completed due to speaker installation, the measuring environment, etc., an error message is
displayed. If this happens, check the relevant items, be sure to take the necessary measures, then perform the Audyssey Auto Setup procedure
over again.
Connections
NOTE Be sure to turn the power off before checking the speaker connections.
Error messages (examples)
Settings
MultEQ
FMicrophone:None
or
Speaker
:None
Playback
•Not all speakers could be detected.
•The front L speaker was not properly detected.
This is displayed after the Audyssey Auto Setup procedure is
completed.
ui to select
1 Press
“Parameter Check”,
Cause
•Included setup microphone is not connected.
Caution
Check Audyssey Auto Setup
Measurement Results (Parameter Check)
Measures
•Connect the included setup microphone to the
SETUP MIC jack on the main unit.
•Check the speaker connections.
then press
.
“Parameter Check” is
displayed on the on-screen
display.
3-2.Parameter Check
Speaker Config.Check
Distance Chenck
Channel Level Check
Crossover Freq.Check
EQ Check
Restore
[ENT]:Select [RTN]:Back
Retry
Cancel
Remote Control
[ENT]:Retry
Caution
MultEQ
FAmbient noise is
too high or
Level is too low.
Information
Retry
Cancel
•Too much noise in the room for accurate
measurements to be made.
•Speaker or subwoofer sound is too low for
accurate measurements to be made.
•Either turn off any device generating noise or
move it away.
•Try again when the surroundings are quieter.
•Check the speaker installation and the direction
in which the speakers are facing.
•Adjust the subwoofer’s volume.
ui to select the item you want to check, then
2 Use
press
.
Speaker Config. Check :Check the speaker configuration
Distance Check
[ENT]:Retry
Caution
Troubleshooting
MultEQ
Front
R :None
Retry
Cancel
Skip
]:Up/Down [
[
]:CH
Specifications
Caution
MultEQ
•Displayed speaker could not be detected.
· The front R speaker were not properly detected.
· Only one channel of the surround speakers was
detected.
· Sound was output from the R channel when only
one surround back speaker was connected.
· The surround back, but the surround speaker was
not detected.
•Displayed speaker connected with the polarities
reversed.
Front
L :Phase
Retry
Cancel
Skip
]:Up/Down [
[
]:CH
n To perform the Audyssey Auto Setup procedure again
Press ui to select “Retry”, then press
.
n To cancel Audyssey Auto Setup
Use ui to select “Cancel”, then select “Yes” using o p.
23
•Check the
speaker.
connections
of
the
displayed
Channel Level Check
: Check the distance
: Check the channel level
Crossover Freq. Check :Check the crossover frequency
EQ Check
: Check the equalizer
o p to switch the display between the different
3 Use
speakers.
4 Press .
•Check the polarities of the displayed speaker.
•For some speakers, this error message may
be displayed even if the speaker is properly
connected. If you are sure that the wiring is
correct, press ui to select “Skip”, then press
.
The confirmation screen reappears. Repeat steps 2 and 3.
Even if the settings are changed after the Audyssey Auto Setup
procedure, the Audyssey Auto Setup settings can be restored by
selecting “Restore” then pressing
.
ENGLISH
Making other settings (Option Setup) vpage 28
Speaker Config.
Speaker Setup
HDMI Setup
4-1.Speaker Setup
4-2.HDMI Setup
1.Pre Assign
2.Speaker Config.
3.Bass Setting
4.Distance
5.Channel Level
6.Crossover Freq.
Auto Lipsync
: ON
HDMI Audio Out : Amp
HDMI Control
: OFF
NOTE
Audio Setup
[RTN]:Back
Option Setup
4-3.Audio Setup
4-4.Option Setup
1.Auto Surround Mode
2.EQ Customize
1.Volume Control
2.Source Delete
3.On-Screen Display
4.Quick Select Name
5.Setup Lock
[ENT]:Select [RTN]:Back
Select “Large” or “Small” not
according to the physical size
of the speaker but according
to
the
low
frequency
reproduction
capabilities
based on the frequency set
at “Crossover Frequency”
(vpage 26).
When “Front” is set to “Small”, “Subwoofer” can automatically set
to “Yes”.
[ENT]:Select [RTN]:Back
See overleaf
Remote control
operation buttons
Displaying the menu
:
Cancel the menu
: Moves the cursor (Up/Down/Left/Right)
: Decision the setting
: Return to previous menu
24
Specifications
[ENT]:Select [RTN]:Back
•“Large” is not displayed when “Front” is set to “Small”.
•Even if “Center” has been set to “Large”, when “Front” is set to
“Small”, the “Center” setting automatically switches to “Small”.
• Subwoofer : Set the presence of a subwoofer.
• Yes : Use a subwoofer.
• No : Select when a subwooofer is not connected.
Troubleshooting
If “Subwoofer” is set to “No”, “Front” is automatically set to “Large”.
Center : Set the presence and size of the center speaker.
• Large : Use of a large speaker that can adequately play back low
frequencies.
• Small : Use of a small speaker that has inadequate playback capacity for
low frequencies.
• None : Select when a center speaker is not connected.
nExamples of Menu Screen Displays
Information
Front : Set the front speaker size.
Select speaker configuration • Large : Use of a large speaker that can adequately play back low
frequencies.
and size.
(bass reproduction capability) • Small : Use of a small speaker that has inadequate playback capacity for
low frequencies.
Remote Control
Making the audio settings (Audio Setup) vpage 28
Setting contents
Pre Assign
Normal : The surround back channel audio signals are output.
Sets the signal output Front Height : The front height channel audio signals are output.
from the SURR. BACK /
FRONT HEIGHT PRE OUT
connectors.
Playback
Making the HDMI settings (HDMI Setup) vpage 27
Setting items
Settings
Making the speaker settings (Speaker Setup) vpage 24
Default settings are underlined.
Use this procedure to set the speakers manually or if you wish to change the settings made with
the Audyssey Auto Setup procedure.
n Items that can be set with the Manual Setup procedure
Making the speaker settings (Speaker Setup)
Connections
Use this procedure to change the Audyssey Auto Setup settings or to change the various audio,
video and display settings.
The set can be used without changing these settings. Make these settings as necessary.
For a description of “Menu map” and operating instructions, see page 17.
Getting Started
Making detailed settings (Manual Setup)
ENGLISH
Getting Started
Making detailed settings (Manual Setup)
Setting items
Setting contents
Setting items
Speaker Config.
Connections
Surround : Set the presence and size of the Surround speakers.
Select speaker configuration • Large : Use of a large speaker that can adequately play back low
frequencies.
and size.
(bass reproduction capability) • Small : Use of a small speaker that has inadequate playback capacity for
low frequencies.
• None : Select when the surround speakers are not connected.
Settings
Playback
“S.Back” is displayed
when the “Pre Assign”
setting (vpage 24) is
set to “Normal”.
Remote Control
“Large” is not displayed when “Front” is set to “Small”.
S.Back (Pre out) : Set the presence, size and number of surround back
speakers.
• Large : Use of a large speaker that can adequately play back low
frequencies.
• Small : Use of a small speaker that has inadequate playback capacity for
low frequencies.
• None : Select when the surround back speakers are not connected.
• 2ch : Use two surround back speakers.
• 1ch : Use only one surround back speaker. Surround back audio is output
from the SURR. BACK / FRONT HEIGHT PRE OUT “L” connector.
Information
•“Large” is not displayed when “Surround” is set to “Small”.
•Even if “S.Back” is set to “Large”, the “S.Back” setting is automatically
switched to “Small” if “Surround” is set to “Small”.
NOTE
Troubleshooting
Specifications
“Front
Height”
is
displayed when the “Pre
Assign” setting (vpage
24) is set to “Front
Height”.
Even when the Surround Back Speaker setting is other than “None”,
sound may not be emitted from the surround back speaker, depending
on the playback source. In this case, “Surround Back” setting other
than “OFF” (vpage 40).
Front Height (Pre out) : Set the front height speaker size.
• Large : Use of a large speaker that can adequately play back low
frequencies.
• Small : Use of a small speaker that has inadequate playback capacity for
low frequencies.
• None : Select when a front height speaker is not connected.
NOTE
Select “Large” or “Small” not according to the physical size
of the speaker but according
to
the
low
frequency
reproduction
capabilities
based on the frequency set
at “Crossover Frequency”
(vpage 26).
25
Remote control
operation buttons
Bass Setting
Subwoofer Mode : Select low range signal to be reproduced by
Make the settings related to subwoofer.
playback of low frequency • LFE : Add the low frequency signal of the channel for which the speaker
signals (subwoofer and LFE). size is set to “Small” to the subwoofer signal and output it.
• LFE+Main : Add the low frequency signal of all channels to the subwoofer
This can be set when
signal and output it.
“Speaker
Config.”
–
•Play music or a movie source and select the mode offering the
“Subwoofer” (vpage
strongest bass.
24) is set to “Yes”.
•Select “LFE+Main” if you want the bass signals to always be
produced from the subwoofer.
LPF for LFE : Set the upper limit of the low frequency signals output from
the subwoofer.
• 80Hz / 90Hz / 100Hz / 110Hz / 120Hz / 150Hz / 200Hz / 250Hz
Unit : Set the unit of distance.
Distance
Set the distance from the • Feet
listening position to the • Meters
Step : Set the minimum variable width of the distance.
speakers.
Measure the distance from • 1ft / 0.1ft
the listening position to the • 0.1m / 0.01m
speakers beforehand.
• FL (Front L)/ FR (Front R)/ C (Center)/ SW (Subwoofer)/ SL (Surround L)/
SR (Surround R/ SBL (Surr. Back L)/ SBR (Surr. Back R)/ FHL (Front Height L)/
FHR (Front Height R) : Select the speaker you want to set, and set the
distance. Set the value that is closest to the measured distance.
• 0.0ft ~ 60.0ft / 0.00m ~ 18.00m
•“Large” is not displayed when “Front” is set to “Small”.
•Even if “Front Height” is set to “Large”, the “Front Height” setting
is automatically switched to “Small” if “Front” is set to “Small”.
Displaying the menu
:
Cancel the menu
Setting contents
: Moves the cursor (Up/Down/Left/Right)
•The speakers that can be selected differ depending on the “Pre Assign”
(vpage 24) and “Speaker Config.” settings.
•Default settings :
Front/Center/Subwoofer/Front Height : 3.6 meters (12 feet)
Surround/Surr. Back : 3.0 meters (10 feet)
NOTE
Set the difference in the distance between the speakers to less than 6.0
meters (20 feet). “Relocate Speaker” is displayed on the screen if an
inappropriate distance is set.
Default : Reset all distance settings to factory default.
• Yes : Reset to the defaults.
• No : Do not reset to the defaults.
: Decision the setting
: Return to previous menu
ENGLISH
Setting items
Channel Level
Setting items
Crossover Frequency
Remote control
operation buttons
Displaying the menu
:
Cancel the menu
: Moves the cursor (Up/Down/Left/Right)
Specifications
Default : Reset all channel level settings to factory default.
Yes : Reset to the defaults.
No : Do not reset to the defaults.
Crossover : Outputs at below set frequency, each speaker’s bass signal
output from the subwoofer.
• 40Hz / 60Hz / 80Hz / 90Hz / 100Hz / 110Hz / 120Hz / 150Hz / 200Hz /
250Hz
• Advanced : Set the low frequency signals to be output from the signals
of the respective speakers to the subwoofer.
• Front / Center / Surround / S.Back / Front Height : Select the speaker.
· 40Hz / 60Hz / 80Hz / 90Hz / 100Hz / 110Hz / 120Hz / 150Hz / 200Hz /
250Hz : Set the crossover frequency.
Troubleshooting
This can be set when
“Speaker Config.” –
“Subwoofer” (vpage
25) is set to “Yes” or
“No”.
Information
Outputs at below set
frequency, each speaker’s
bass signal output from the
subwoofer. Set this according
to the low frequency
reproduction capabilities of
the speakers you are using.
Remote Control
Crossover Frequency
Playback
•When “Channel Level” is adjusted, the adjusted values are set for
all the surround modes. To adjust the channel level separately for the
different surround modes, use the operation see “Adjust the volume of
the different speakers” (vpage 45).
•Speakers set to “None” in the “Speaker Config.” (vpage 25) settings
are not displayed.
•When o is pressed while the subwoofer volume is set to “–12dB”, the
“Channel Level” setting switches to “OFF”.
•If output of the test tones begins while the muting mode is set, the
muting mode is canceled.
•Always set the crossover frequency to “80 Hz”. When using small
speakers, however, we recommend setting the crossover frequency
to a higher frequency.
•For speakers set to “Small”, sound below the crossover frequency
is cut from the sound output. The cut bass sound is output from the
subwoofer or front speakers.
•The speakers that can be set when “Advanced” is selected differ
according to the “Bass Setting” setting (vpage 25).
· When “LFE” is selected, speakers set to “Small” at “Speaker
Config.” (vpage 25) can be set.
· When “LFE+Main” is selected, speakers can be set regardless of
the speaker size setting.
Settings
Test Tone Start : Output test tones.
FL (Front L)/ C (Center)/ FR (Front R)/ SR (Surround R)/
SBRz (Surround Back R)/ SBLz (Surround Back L)/ SL (Surround L)/
FHL (Front Height L)/ FHR (Front Height R)/ SW (Subwoofer) : Select
the speaker.
zWhen the “S.Back” setting (vpage 25) is set to “1ch”, “SB” is
displayed.
• –12.0dB ~ +12.0dB (0.0dB) : Adjust the volume.
Setting contents
Connections
Set the volume of the test
tone to be the same when it
is output from each speaker.
Setting contents
Getting Started
Making detailed settings (Manual Setup)
: Decision the setting
: Return to previous menu
26
ENGLISH
Getting Started
Making detailed settings (Manual Setup)
Setting items
Making the HDMI settings (HDMI Setup)
Default settings are underlined.
Connections
Make settings for HDMI video/audio output.
Setting items
Settings
Playback
Auto Lip Sync
Automatic
compensation
for timing shift in audio and
video output.
HDMI Audio Out
Select HDMI audio output
device.
Setting contents
ON : Compensated.
OFF : Not compensated.
Setting contents
Power Off Control
ON:Switched.
The power of the AVR-590 OFF:Not switched.
and external device turn off
•Please consult the operating instructions for each connected device
together.
to check the settings.
•For details on the HDMI control function, see “Controlling HDMIThis can be set when
compatible devices from the AVR-590 (HDMI Control Function)”
“HDMI Control” is set
to “ON”.
(vpage 44).
Amp : Use speakers connected to AVR-590 for audio playback.
TV : Use speakers of TV for audio playback.
NOTE
Remote Control
Information
Troubleshooting
Specifications
When the HDMI control function is operating, the setting of audio playback
in the connected TV takes priority (vpage 44 “Controlling HDMIcompatible devices from the AVR-590 (HDMI Control Function)”).
HDMI Control
ON : Use the HDMI control function.
External devices can be OFF : Do not use the HDMI control function.
controlled from the AVR•Please consult the operating instructions for each connected device
590 and the AVR-590 can
to check the settings.
be controlled from external
•
For details on the HDMI control function, see “Controlling HDMIdevices.
compatible devices from the AVR-590 (HDMI Control Function)”
NOTE
(vpage 44).
The
HDMI
control
NOTE
function
controls
•When “Control” is set to “ON”, it consumes more standby power.
operations of a TV that
•When not using this unit for a long period, we recommend that you press
is compatible with the
to turn off (jOFF) the power.
HDMI control function.
•When the “HDMI Control” setting has been changed, always turn off the
Make sure that the TV
power to the connecting devices afterwards and then turn back on.
and HDMI are connected
•The “HDMI Control” does not work when the power to the equipment is
when you perform HDMI
off.
control.
Standby Source
Last : Standby with last used input source during power on.
Set the HDMI connector for HDMI1 / HDMI2 / HDMI3 : The standby mode is set at the input source
HDMI signal input during assigned to the respective.
standby.
This can be set when
“HDMI Control” is set
to “ON”.
27
Remote control
operation buttons
Displaying the menu
:
Cancel the menu
: Moves the cursor (Up/Down/Left/Right)
: Decision the setting
: Return to previous menu
ENGLISH
Making the audio settings (Audio Setup)
Making other settings (Option Setup)
Default settings are underlined.
Setting items
Setting contents
ON : Memorize settings. Most recently stored surround mode is
automatically selected.
OFF : Do not memorize settings. Surround mode does not change
according to input signal.
NOTE
NOTE
•The currently selected input source cannot be set.
•Input sources set to “Delete” cannot be selected using
.
Text : The mode name is displayed when the operation for switching the
surround mode, input mode, etc., is performed.
• ON : Turn display on.
• OFF : Turn display off.
Master Volume : Master volume display during adjustment.
• Bottom : Displayed at the bottom of the screen.
• Top : Displayed at the top of the screen.
• OFF : Turn display off.
See overleaf
Remote control
operation buttons
Displaying the menu
:
Cancel the menu
: Moves the cursor (Up/Down/Left/Right)
: Decision the setting
: Return to previous menu
28
Specifications
On-Screen Display
Screensaver : Make screensaver settings.
Make the settings related to • ON : The screen switches to the screensaver if no operation is performed
displays on the TV screen.
for approximately 3 minutes while a menu is displayed or while an iPod
screen is displayed. When you press uio p, the screen saver is
cancelled and the screen before that screen saver started is displayed.
• OFF : Turn the screensaver function off.
Troubleshooting
•Set so that the “Audyssey Byp. L/R” and “Audyssey Flat” settings can be
made when the Audyssey Auto Setup procedure is performed.
•Equalizer settings for which “Not Used” is set with the Quick Select
function cannot be stored and called out.
Information
is used.
Remote Control
when
Power On Level : This sets the volume set when the MAIN ZONE’s power
is turned on.
• Last : Use the memorized setting from the last session.
• – – – : Always use the muting on condition when power is turned on.
• –80dB(1) ~ +18dB(99) : The volume is adjusted to the set level.
Mute Level : This sets the amount of attenuation of the volume when the
mute mode is set in the MAIN ZONE.
• Full : The sound is cut off entirely.
• –40dB : The sound is attenuated by 40 dB.
• –20dB : The sound is attenuated by 20 dB.
Source Delete
TUNER / DVD / HDP / TV / SAT/CBL / VCR / DVR / V.AUX : Select the
Remove
input
sources sources you do not want to use.
that are not used from the • ON : Use this source.
display.
• Delete : Do not use this source.
Playback
The auto surround mode function lets you store in the memory the
surround mode last used for playing the four types of input signals
listed below.
q Analog and PCM 2-channel signals
w Dolby Digital and DTS 2-channel signals
e Dolby Digital and DTS multi-channel signals
r Multi-channel signals other than Dolby Digital and DTS (PCM, etc.)
EQ Customize
Audyssey Byp. L/R / Audyssey Flat / Manual
Set so that unused equalizer • Used
settings are not displayed • Not Used
Volume Control
Volume Display : Set the volume display method.
Set the MAIN ZONE volume • Relative : The volume is displayed within the range of – – –dB (Minimum),
setting.
–80 dB ~ +18 dB.
• Absolute : The volume is displayed within the range of 0, 1 ~ 99.
Vol.Limit : Make a setting for maximum volume.
• OFF : Do not set a maximum volume.
• –20dB(61) / –10dB(71) / 0dB(81)
Settings
Setting items
Auto Surround Mode
Make setting for memorizing
surround mode setting for
each input signal type.
Setting contents
Connections
Make settings for audio playback.
Default settings are underlined.
Getting Started
Making detailed settings (Manual Setup)
ENGLISH
Getting Started
Making detailed settings (Manual Setup)
Setting items
Setting contents
Setting items
Connections
On-Screen Display
Tuner Information : This sets the time the on-screen display is displayed
Make the settings related to when a tuner operation is performed.
displays on the TV screen.
• Always : Show display continuously.
• 30sec : Show display for 30 seconds after operation.
• 10sec : Show display for 10 seconds after operation.
• OFF : Turn display off.
Settings
Playback
Remote Control
iPod Information : This sets the time the on-screen display is displayed
when an iPod operation is performed.
• Always : Show display continuously.
• 30sec : Show display for 30 seconds after operation.
• 10sec : Show display for 10 seconds after operation.
• OFF : Turn display off.
Quick Select Name
Rename Label : Change the display name of the selected “Quick Select”
Change the Quick Select setting.
name.
1.Use ui to select the name of the Quick Select setting you want
to change, then press
.
2.Use o p to set the cursor to the character you want to change.
3.Use ui to change the character, then press
.
Quick Select Name
Setup Lock
Protect
settings
inadvertent change.
Setting contents
Default : The changed display names are reset to the defaults.
• Yes : Reset to the defaults.
• No : Do not reset to the defaults.
• ON : Turn protection on.
from • OFF : Turn protection off.
When “Setup Lock” is set to “ON”, the settings listed below can
no longer be changed. Also, “SETUP LOCKED!” is displayed if you
attempt to operate related settings.
・RESTORER
・Dynamic Volume
・MultEQ
・Channel Level
・Dynamic EQ
・Audio Delay
Information
• Up to 16 characters can be input.
• The input character type can be switched by pressing
while the
display name is being changed.
• The types of characters that can be input are as shown below.
Troubleshooting
GCapital lettersH A B C D E F G H I J K L M N O P Q RST U V W X Y Z
GSmall lettersH a b c d e f g h i j k l m n o p q r s tu v w x y z
GSymbolsH
’()b+–./:;<=>?[]
GNumbersH
01 2 3 4 5 6 7 8 9 (space)
Specifications
4.Repeat steps 2 and 3 to change the display name.
Template : The display name can be changed by selecting “Operation” and
“Device Name” from the previously set templates.
1.Use ui to select the name of the Quick Select setting you want
to change, then press
.
2.Use ui to select “Template”, then press
.
3.Use ui to select “Operation”, then press
.
• Watch / Listen to / Play / For
4.Use uio p to select “Device Name ”, then press
.
•DVD / Blu-Ray / HDP / TV / Cable TV / Satellite / VCR / DVR / iPod /
V.AUX / LD / Movie (When “Operation” is selected to “Watch”.)
•CD / TUNER / iPod / MD / TAPE / MUSIC (When “Operation” is
selected to “Listen to”.)
•PC / Game (When “Operation” is selected to “Play”.)
•Father / Mother / Son / Daughter / Brother / Sister / Grandfather
/ Grandmother / Me (When “Operation” is selected to “For”.)
29
Remote control
operation buttons
Displaying the menu
:
Cancel the menu
: Moves the cursor (Up/Down/Left/Right)
: Decision the setting
: Return to previous menu
ENGLISH
Getting Started
Making the input settings (Input Setup)
nExamples of Menu Screen Displays
Make the settings related to the currently selected input source.
DVD
HDP
TV
SAT/CBL
VCR/iPod
DVR
1
2
1
Input Mode
Decode Mode
DVD
: Auto
: Auto
01
C1
3
2
[ENT]:Select [RTN]:Back
Source Level
Source Level
: DVD
Defaulut
02
:
[RTN]:Back
[
]:Up/Down [ ]:Rename
[RTN]:Back
iPod Playback Mode
5-4.Source Level
5-5.iPod Playback Mode
0dB
Repeat Mode
Shuffle Mode
:
:
One
OFF
Remote Control
Changing the Input Source’s Input Mode and Decoding mode (Input
mode) vpage 32
Rename
5-3.Rename
Playback
Changing the Input Sources Assigned to the Input Connectors (Assign)
vpage 31
Input Mode
5-2.Input Mode
Changing the Input Source’s Display Name (Rename) vpage 32
[RTN]:Back
Setting the iPod Playback Mode (iPod Playback Mode) vpage 33
Auto Preset
5-1.Auto Preset
Auto Tuning
Preset Station Memory
Storing Preset Memory
[ENT]:Start [RTN]:Back
5-2.Preset Skip
Block
:
A Block Presets:
A1 FM 87.50MHz :
A2 FM 89.10MHz :
A3 FM 98.10MHz :
A4 FM107.90MHz :
A5 FM 90.10MHz :
A6 FM 90.10MHz :
A7 FM 90.10MHz :
A8 FM 90.10MHz :
Preset Name
A
ON
ON
ON
ON
ON
ON
ON
ON
ON
5-3.Preset Name
Block: A
A1FM 87.50MHz:
A2FM 89.10MHz:
A3FM 98.10MHz:
A4FM107.90MHz:
A5FM 90.10MHz:
A6FM 90.10MHz:
A7FM 90.10MHz:
A8FM 90.10MHz:
[ENT]:Select [RTN]:Back
Setting the Preset Channels to be Skipped (Preset Skip) vpage 33
Specifications
Assign Name to a Preset Memory (Preset Name) vpage 33
Remote control
operation buttons
Displaying the menu
:
Cancel the menu
: Moves the cursor (Up/Down/Left/Right)
Troubleshooting
Start
Presetting Radio Stations (Auto Preset) vpage 33
[RTN]:Back
Preset Skip
Information
Correcting the Input Source’s Playback Level (Source Level)
vpage 33
Settings
n Items that can be set with the Input Setup procedure
Assign
5-1-1.Input Assign
HDMI Digi Comp
Connections
Before displaying the menu screen, press
to switch to the input source to be set.
The items that can be set differ according to the selected input source.
The set can be used without changing these settings. Make these settings as necessary.
For a description of “Menu map” and operating instructions, see page 17.
: Decision the setting
: Return to previous menu
30
ENGLISH
Getting Started
Making the input settings (Input Setup)
Changing the Input Sources Assigned to the Input Connectors
(Assign)
Default settings are underlined.
Connections
Setting items
Setting contents
Settings
Input Assign (HDMI)
TV
SAT/CBL VCR
DVR V.AUX input
HDMI : The DVD HDP
Assign input sources to input
sources are assigned to the HDMI input connectors as shown below.
connectors.
• HDMI1 / HDMI2 / HDMI3
• None : Do not assign an HDMI input connector to the currently selected
input source.
Setting items
Setting contents
Input Assign (Component)
TV
SAT/CBL VCR DVR V.AUX
Component : The DVD HDP
Assign input sources to input
input sources are assigned to the component video input connectors as
connectors.
shown below.
● COMP1 (Component video 1 input connector) / COMP2 (Component
video 2 input connector)
● None : Do not assign the component video input connectors to the currently
selected input source.
bUpon purchase, the settings of the different input sources are as shown
below.
Playback
bUpon purchase, the settings of the different input sources are as shown
below.
Remote Control
Input
source
DVD
Default
setting
HDP
HDMI1 HDMI2
TV
SAT/CBL
VCR
DVR
V.AUX
None
HDMI3
None
None
None
Information
•When HDMI is assigned to an input source, the audio signal switches
to HDMI along with the video signal. To use with the digital audio
input connectors assigned, set menu “Input Mode” (vpage 32) to
“Digital”.
•When the AVR-590 and TV are connected with an HDMI cable, if the
TV is not compatible with HDMI audio signal playback, only the video
signals are output to the monitor.
•The audio signals input from the analog, digital and EXT. IN connectors
are not output to the TV.
Input
source
DVD
HDP
TV
SAT/CBL
VCR
DVR
V.AUX
Default
setting
COMP1
None
None
None
None
COMP2
None
iPod Dock
The control dock for iPod can be assigned to the DVD SAT/CBL VCR
Change the input source to
DVR V.AUX input sources.
which the control dock for
Assign
: Assign the currently selected input source to the Control Dock for
iPod is assigned.
iPod input.
None : Do not assign the currently selected input source to the Control Dock
for iPod input.
Troubleshooting
•With the default settings, the control dock for iPod can be used
connected to the VCR (iPod) connector.
•Even if “iPod Dock” is set to “Assign”, if AVR-590 and control dock
for iPod are not connected, the input is used as the normal input
source.
NOTE
Specifications
When “HDMI Control” is set to “ON”, HDMI cannot be assigned to “TV”
at the “HDMI” settings (vpage 27).
Input Assign (Digital)
TV
SAT/CBL VCR DVR V.AUX input
Digital : The DVD HDP
Assign input sources to input
sources are assigned to the digital audio input connectors as shown
connectors.
below.
• C1 (COAXIAL) / O1 (OPT1) / O2 (OPT2)
• None : Do not assign a digital input connector to the currently selected
input source.
bUpon purchase, the settings of the different input sources are as shown
below.
31
Input source
DVD
HDP
TV
SAT/CBL
VCR
Default setting
None
None
OPT1
COAXIAL
None
Input source
DVR
V.AUX
Default setting
OPT2
None
Remote control
operation buttons
Displaying the menu
:
Cancel the menu
: Moves the cursor (Up/Down/Left/Right)
: Decision the setting
: Return to previous menu
ENGLISH
Changing the Input Source’s Input Mode and Decoding mode
(Input Mode)
Default settings are underlined.
Setting items
Decode Mode
Set the input
decoding mode.
Setting items
Auto : Detect type of digital input signal and decode and play
source’s automatically.
PCM : Decode and play only PCM input signals.
DTS : Decode and play only DTS input signals.
bUpon purchase, the settings of the different input sources are as shown
below.
HDP
TV
SAT/CBL
VCR
Default
setting
Auto
HDMI
Digital
Auto
Analog
Input
source
DVR
V.AUX
TUNER
Default
setting
Auto
Analog
Analog
Use this procedure to change the display name of the currently selected input source.
Setting items
GCapital lettersH ABCDEFGHIJKLMNOPQRSTUVWXYZ
GSmall lettersH abcdefghijklmnopqrstuvwxyz
GSymbolsH
’()b+–./:;<=>?[]
GNumbersH
0123456789 (space)
Troubleshooting
•The “HDMI” settings are made for input sources for which HDMI
input connectors are assigned at “Assign” (vpage 31).
•The “Digital” settings are made for input sources for which digital
input connectors are assigned at “Assign” (vpage 31).
•When a digital signal is properly input, the “
” indicator lights on
the display. If the “
” indicator does not light, check the digital
input connector assignment and the connections.
Setting contents
Rename
1.Use o p to set the cursor to the character you want to change.
Change the input source’s 2.Use ui to change the character, then press
.
display name to the desired
• Up to 8 characters can be input.
name.
• The input character type can be switched by pressing
while the
display name is being changed.
• The types of characters that can be input are as shown below.
Specifications
Default
Yes : Reset to the defaults.
The changed display names No : Do not reset to the defaults.
are reset to the defaults.
•This can also be set by pressing
or
.
Each time you press the button, the input mode display will change.
Auto
Remote control
operation buttons
HDMI
Displaying the menu
:
Cancel the menu
Digital
Analog
: Moves the cursor (Up/Down/Left/Right)
: Decision the setting
Information
DVD
Default settings are underlined.
Remote Control
Input
source
Changing the Input Source’s Display Name (Rename)
Playback
Input Mode
Auto : Automatically detect input signal and perform playback.
Set the audio input modes for HDMI : Play only signals from HDMI input.
the different input sources. Digital : Play only signals from digital input.
Analog : Play only signals from analog input.
Settings
•This can be set for input sources for which “HDMI” or “Digital” is
assigned at “Assign” (vpage 31).
•Normally set this to “Auto”.
Setting contents
Connections
The selectable input modes depend on the input source and “Assign” setting (vpage
31 “Changing the input sources assigned to the input connectors”).
Setting contents
Getting Started
Making the input settings (Input Setup)
: Return to previous menu
32
ENGLISH
Getting Started
Making the input settings (Input Setup)
Setting the Preset Channels to be Skipped (Preset Skip)
Correcting the Input Source’s Playback Level
(Source Level)
Default settings are underlined.
Default settings are underlined.
Connections
Use this procedure to correct the playback level of the currently selected input source's audio input.
Set this if there are differences in the input volume levels between the different sources.
Setting items
Setting contents
Settings
Source Level
–12dB ~ +12dB (0dB)
Correct the playback level of
the audio input.
Playback
Remote Control
Default settings are underlined.
This can be selected for input sources for which “Assign” is assigned at the “iPod Dock” (vpage
31) setting.
Preset Skip
This can be set when the source is set to TUNER .
Set the preset memories that
A ~ G : Select the preset channel(s) you do not want to display.
you do not want to display
• ON : Display this number.
when tuning.
• Skip : Skip this number.
Assign Name to a Preset Memory (Preset Name)
Default settings are underlined.
Setting items
Setting contents
Information
Preset Name
This can be set when the source is set to TUNER .
Assign name to a preset
1.Use ui to select the preset channel name you want to change,
memory.
then press
.
Setting contents
Repeat
All : Repeat all songs.
Make settings for repeat One : Repeat the current song.
mode.
OFF : Cancel repeat mode.
Troubleshooting
Shuffle
nWhen DENON control dock for iPod ASD-1R or ASD-11R is
Make settings for shuffle
connected
mode.
Songs : Shuffle all songs.
Albums : Shuffle songs from current album only.
OFF : Cancel shuffle mode.
Specifications
Presetting Radio Stations (Auto Preset)
Default settings are underlined.
Setting items
Setting contents
If you set “Block Presets” to “Skip”, you can skip the preset memory
blocks (A to G).
Setting the iPod Playback Mode (iPod Playback Mode)
Setting items
Setting items
Setting contents
2.Use o p to set the cursor to the character you want to change.
3.Use ui to change the character, then press
.
•Up to 8 characters can be input.
•The input character type can be switched by pressing
while the
display name is being changed.
•The types of characters that can be input are as shown below.
GCapital lettersH ABCDEFGHIJKLMNOPQRSTUVWXYZ
GSmall lettersH abcdefghijklmnopqrstuvwxyz
GSymbolsH
’()b+–./:;<=>?[]
GNumbersH
0123456789 (space)
4.Repeat steps 2 and 3 to change the display name.
Auto Preset
This can be set when the source is set to TUNER .
Use the auto preset function
Start : Start the auto preset process.
to program radio stations.
If an FM station cannot be preset automatically, select the desired station
by tuning it in manually, then preset it manually.
33
Remote control
operation buttons
Displaying the menu
:
Cancel the menu
: Moves the cursor (Up/Down/Left/Right)
: Decision the setting
: Return to previous menu
ENGLISH
Playing Components
n Operation Flow
Before starting playback, make the connections between the
different components and the settings on the receiver.
Playing Components (vpage 34)
e Direct Playback (vpage 38)
and player.
②Set the TV’s input to the AVR-590.
③Load the disc in the player.
2
(vpage 31).
and select the input
If “TUNING PRESET” is selected for preset
channel, press
before turning
.
the component connected to the AVR-590.
4 Play
Make the necessary settings on the player (language
setting, subtitles setting, etc.) beforehand.
5
Use
to adjust the volume.
GVariable rangeH – – –
wAssign the control dock for iPod’s input
–80.0dB ~ 18.0dB
eSwitch
to “DEVICE”.
2
3
Turn on the AVR-590’s power.
(vpage 16 “Turning the Power On”)
Press
to select the input
source assigned in step 1-w
above.
b If the screens above are not
displayed, the iPod may not be
properly connected. Try connecting
again.
OK to disconnect.
Specifications
Also refer to the operating instructions of the connected
components when playing them.
● External devices can be controlled by remote control unit
(vpage 46 “Operating the Connected Devices by Remote
Control Unit”).
●
dock for iPod.
Troubleshooting
NOTE
qSet the iPod in the DENON control
(vpage 16 “Turning the Power On”)
rStereo Playback (vpage 39)
Adjusting the Sound Field Effects (Parameter)
(vpage 39)
1Prepare for playback.
Turn on the AVR-590’s power.
3 Press
source.
Listening to music on an iPod®
Information
w Playing in a DENON original surround mode
(vpage 38)
①Turn on the power of the TV, subwoofer
Remote Control
q Standard Playback (vpage 37)
1Prepare for playback.
The music / video on an iPod can be played by using the control
dock for iPod (ASD-1R, ASD-11R, ASD-3N or ASD-3W sold
separately).
Connect the control dock for iPod beforehand. (vpage 14
“iPod®”).
Playback
Selecting the Surround Mode (vpage 37)
The following describes the procedure for playing Blu-ray disc/
DVD players.
Use the same procedure to play other components.
Settings
nPlaying Blu-ray Disc/DVD Players (vpage 34)
niPod® Playback (vpage 34)
nListening to FM/AM Broadcasts (vpage 36)
nOperations During Playback (vpage 37)
iPod® Playback
Playing Blu-ray Disc / DVD Players
Connections
Getting Started
Playback
(iPod screen)
※The variable range differs according to the input signal and channel
level setting.
6 Select the desired surround mode.
7 Adjust the desired sound field effects.
(vpage 37 “Selecting the Surround Mode”)
(vpage 39 “Adjusting the Sound Field Effects”)
See overleaf
34
ENGLISH
Getting Started
Playing Components
and hold it down for a 2 seconds or more to
4 Press
select the display mode.
Connections
There are two modes for display the contents recorded on the
iPod.
Browse mode :Displayed on the TV screen.
Settings
Display mode
Audio file
Playback
Playable
files
Video file
Remote Control
Active
buttons
Browse mode
Remote mode
S
S
Sz1
S
S
iPod®
A
S
z1:When using an ASD-11R, ASD-3N or ASD-3W control dock for
iPod.
z2:Video may not be output, depending on the combination of
ASD-1R or ASD-11R and iPod.
Information
Troubleshooting
5
6
Press
or p.
to adjust the volume.
Specifications
GVariable rangeH – – –
–80.0dB ~ 18.0dB
※The variable range differs according to the input signal and channel
level setting.
8 Select the desired surround mode.
9 Adjust the desired sound field effects.
(vpage 37 “Selecting the Surround Mode”)
(vpage 39 “Adjusting the sound Field Effects”)
35
.
nStopping playback temporarily
During playback, press
or
Press again to resume playback.
.
nTo cue to the beginning of a
track
During playback,
the current track) or
either press (to cue to
(to cue to the next
track).
nRepeat playback and shuffle
playback
“iPod Playback Mode” (vpage 33)
• Use the RESTORER mode to expand the low and high frequency
components of compressed audio files and achieve a richer sound.
The default setting is “Mode3” (vpage 43).
• Photo and video data on the iPod can be viewed on the monitor. Only
for iPod equipped with slideshow or video functions. (When using an
ASD-1R or ASD-11R)
• Video may not be output, depending on the combination of ASD-1R
or ASD-11R and iPod.
and hold
1 Press
mode.
to set the Remote
“Remote iPod” is displayed on the AVR590’s display.
the iPod’s screen,
2 Watching
use ui to select “Photos” or
“Videos”.
until the image you want to view is
3 Press
displayed.
“TV Out” at the iPod’s “Slideshow Settings” or “Video Settings” must
be set to “On” in order to display the iPod’s photo data or videos on
the monitor. For details, see the iPod’s operating instructions.
• To check the name of the title, the artist or the album when playing
in browse mode, press
Playback starts.
7 Use
or press
Sz2
Remote control
unit (AVR-590)
Use ui to select the menu, then
press
or p to select the music
or video file to be played.
During playback, either press and hold
Remote mode :Displayed on the iPod’s screen.
Viewing Still Pictures or Videos on the iPod®
nTo stop
.
• The time (default : 30 sec) for which the on-screen display are
displayed can be set at menu “iPod Information” (vpage 29).
Press uio p to return to the original screen.
• Press
and set the AVR-590’s power to the standby mode before
disconnecting the iPod. Also switch the input source to one to which
the menu “iPod dock” is not assigned before disconnecting the
iPod.
NOTE
• Depending on the type of iPod and the software version, some
functions may not operate.
• DENON will accept no responsibility whatsoever for any loss of iPod
data.
iPod is a trademark of Apple Inc., registered in the U.S. and other
countries. The iPod may only be used to copy or play contents that
are not copyrighted or contents for which copying or playback is
legally permitted for your private use as an individual. Be sure to
comply with applicable copyright legislation.
ENGLISH
Listening to FM/AM Broadcasts
Basic Operation
Set
to “TUNER/AMP”.
Press
to select “FM” or “AM”.
station.
Press
to light the “AUTO” indicator on
the display, then use
station you want to hear.
to select the
Press
to turn off the display’s “AUTO” indicator, then use
to select the station you want to hear.
Press
.
to select the block (A to G)
in which the station is to be preset.
Press
to select the preset number (1 to 8).
again to complete the setting.
•To preset other stations, repeat steps 1 to 5.
•Stations can be preset automatically at menu “Auto Preset” (vpage
33).
NOTE
Auto tuner presets
A1 ~ A8
87.5 / 89.1 / 98.1 / 107.9 / 90.1 / 90.1 / 90.1 /
90.1 MHz
B1 ~ B8
520 / 600 / 1000 / 1400 / 1500 / 1710 kHz,
90.1 / 90.1 MHz
C1 ~ C8
90.1 MHz
D1 ~ D8
90.1 MHz
E1 ~ E8
90.1 MHz
F1 ~ F8
90.1 MHz
G1 ~ G8
90.1 MHz
You can also operate via the main unit. In this
case, perform the following operations.
•Press
, then turn
on the main
unit to select the preset radio channel.
Troubleshooting
Preset stations are erased by overwriting them.
Specifications
•If the desired station cannot be tuned in with auto tuning, tune it in
manually.
•When tuning in stations manually, press and hold
to change
frequencies continuously.
•The time (default : 30 sec) for which the on-screen display are
displayed can be set at “On-Screen Display” (vpage 29).
to select the desired preset channel (1 to
8).
nDefault settings
Press
Press
Press
to select the memory block (A to G).
Information
wTo tune in manually (Manual Tuning)
Remote Control
qTo tune in automatically (Auto Tuning)
Tune in the broadcast station you want to preset.
Press
Playback
Tune in the desired broadcast
1
2
3
4
5
1
2
Settings
Press
to select “TUNER”.
Your favorite broadcast stations can be preset so that you can tune
them in easily. Up to 56 stations can be preset.
Listening to Preset Stations
Connections
1
2
3
4
Presetting Radio Stations (Preset Memory)
Getting Started
Playing Components
36
ENGLISH
Getting Started
Playing Components
Operations During Playback
Selecting the Surround Mode
Select a surround mode to enjoy surround playback with your favorite sound field effects.
Turning Off the Sound Temporarily (Muting)
Connections
Press
q Playing sources according to the sources’ audio signal format/number of channels
(Standard Playback)
.
Operations
Settings
Playback
• The sound is reduced to the level set at menu “Mute Level” (vpage
28).
• To cancel, press
again. Muting can also be canceled by adjusting
the master volume.
Listening with Headphones
Remote Control
Plug the headphones into the PHONES
jack on the main unit.
The sound from the speakers and pre-out
connectors is automatically cut.
Information
NOTE
• To prevent hearing loss, do not raise the volume level excessively
when using headphones.
• Unplug headphones when performing the Audyssey Auto Setup
procedure or other settings.
Troubleshooting
Switching the brightness of the display
Press
.
Bright
Specifications
OFF
Dim
Dark
The selectable surround modes depend on the following:
•Format of the audio signals being input
•Number of channels of the audio signals being input
•The set pre out assignment mode (vpage 24)
1
2
Playing the source (vpage 34).
Press
mode.
to select the surround
This is the operation for playing 2-channel sources.
Select the mode for the source at “Mode” (vpage
39).
nDOLBY PLgx, DOLBY PLg
Cinema
:This mode is suited for movie sources.
Music
:This mode is suited for music sources.
Game
:This mode is suited for games.
Pro Logic :This is the Pro Logic playback mode. This can be
selected when playing with a DOLBY PLg decoder.
When this mode is selected, “DOLBY PL” is
displayed.
nMultichannel sources
The surround modes that can be selected
differ according to the input source.
n2channel sources
When you select “DOLBY PLgz”, set “Pre
Assign” to “Front Height”.
DOLBY PLgx,
DOLBY PLg
or
DOLBY PLgz
DTS NEO:6
being used.
nDTS NEO:6
Cinema
:This mode is suited for movie sources.
Music
:This mode is suited for music sources.
z
:The signals are decoded in DOLBY PLgx,
DOLBY PLg or DOLBY PLgz, for playback.
:The signals are decoded in DTS NEO:6 for
playback.
z:DOLBY PLgx can be selected when surround back speakers are
37
3
※The modes that can be selected depend on the input source
being played.
he “Cinema” and “Music” modes can also be set by pressing
T
or
.
ENGLISH
Displaying the currently playing surround mode
nSurround playback of multichannel sources
(Dolby Digital, DTS, etc.)
Dolby Digital Plus
(z1)
Dolby TrueHD (z1)
DTS-HD (z1)
PCM
(multi ch)
z1:When a signal is input, the HD AUDIO indicator lights.
z2:This is displayed when the input signal is “DTS-ES Matrix 6.1”
and the AVR-590’s “AFDM” setting (vpage 40) is set to “ON”.
z3:This is displayed when the input signal is “DTS-ES Discrete
6.1”.
z4:This is displayed when the input signal is “DTS 96/24”.
to select the Surround
5CH/7CH STEREO :This mode is for enjoying
stereo sound from all
speakers.
ROCK ARENA
JAZZ CLUB
:This mode is for enjoying
the atmosphere of a live
concert in an arena.
:This mode is for enjoying the atmosphere of a
live concert in a jazz club.
MONO MOVIE :This mode is for playing monaural movie
sources with surround sound. z1
VIDEO GAME
:This mode is suited for achieving surround
sound with video games.
MATRIX
:This mode lets you add a sense of expansion
to stereo music sources.
VIRTUAL
:This mode is for enjoying surround effects
using only the front speakers or headphones.
and play the source (vpage
34).
2
Press
to select the “DIRECT”.
Displaying the currently playing surround mode
Input signal
Analog signal /
PCM (2ch) /
Dolby Digital source /
DTS source /
Other 2-channel digital signals
PCM (multi ch)
Display
DIRECT
MULTI CH DIRECT
M DIRECT + PLgx CINEMA
M DIRECT + PLgx MUSIC
M DIRECT + PLgz
M DIRECT 7.1
Specifications
PCM
Press
mode.
Select the input source by pressing
Troubleshooting
DTS
2
1
Information
DTS (5.1ch)/
DTS-ES Discrete 6.1 /
DTS-ES Matrix 6.1 /
DTS 96/24
and play the source (vpage
34).
Remote Control
Dolby
Digital
1
In this mode the signals bypass the tone adjustment circuitry for
high quality sound.
The sound is output to the same channels as the input signal.
Playback
Dolby Digital
(other than 2ch)/
Dolby Digital EX
Display
DOLBY DIGITAL
DOLBY DIGITAL EX
DOLBY DIGITAL+PLgx CINEMA
DOLBY DIGITAL+PLgx MUSIC
DOLBY DIGITAL+PLgz
DOLBY DIGITAL++PLgx C
DOLBY DIGITAL++PLgx M
DOLBY DIGITAL++PLgz
DOLBY TrueHD
DOLBY HD+EX
DOLBY HD+PLgx CINEMA
DOLBY HD+PLgx MUSIC
DOLBY HD+PLgz
DTS SURROUND
DTS+PLgx CINEMA
DTS+PLgx MUSIC
DTS+PLgz
DTS+NEO:6
DTS ES MTRX6.1 (z2)
DTS ES DSCRT6.1 (z3)
DTS 96/24 (z4)
DTS-HD HI RES
DTS-HD MSTR
DTS-HD+NEO:6
DTS-HD+PLgx CINEMA
DTS-HD+PLgx MUSIC
DTS-HD+PLgz
MULTI CH IN
MULTI IN+PLgx CINEMA
MULTI IN+PLgx MUSIC
MULTI IN+PLgz
MULTI CH IN 7.1
Select the input source by pressing
e Direct Playback
Settings
Input signal
The desired mode according to the program source and viewing
situation can be selected from among 7 DENON original surround
modes.
NOTE
When the input signal is DOLBY TrueHD, DOLBY DIGITAL Plus, DTSHD
you cannot select DENON original surround mode.
Connections
In the case of standard playback of multi channel sources, the
AVR-590 recognizes the format of the multi-channel audio input
signal and automatically operates the appropriate decoder for
surround sound.
w Playing in a DENON original surround
mode
Getting Started
Selecting the Surround Mode
z1:When playing sources recorded in monaural in the MONO
MOVIE mode, the sound will be off balance with a single
channel (left or right), so input to both channels.
Depending on the program source being played, it may not be possible
to achieve a satisfactory surround effect. In this case, try other modes
to achieve a sound field suited to your tastes.
38
ENGLISH
Getting Started
Selecting the Surround Mode
Adjusting the Sound Field Effects (Parameter)
r Stereo Playback
Connections
This is the mode for playing in stereo. The tone can be adjusted.
Sound is output from the front left and right speakers and
subwoofer.
1
The sound being played in the surround mode can be adjusted to your liking.
The items (parameters) that can be adjusted depend on the signal being input and the currently set surround
mode. For details on the adjustable parameters, see “Surround Modes and Parameters” (vpage 51).
NOTE
Select the input source by pressing
and play the source (vpage
Settings
34).
Playback
2
Press
Some of the setting items cannot be set while playback is stopped. Set these items during playback.
Adjusting the sound field effects (Surround Parameter)
Default settings are underlined.
to select the “STEREO”.
Setting items
Mode
Setting contents
nIn the PLgx, PLg or PLgz mode
Remote Control
Set the play mode for
playing 2-channel sources in
surround.
Cinema : This is the mode for cinema source.
Music : This is the mode for music source.
Game : This is the mode for game source.
ProLogic : Dolby Pro Logic playback mode (PLg mode only). (This is
the mode for 4-channel playback (front L, front R, center, surround
(MONO).)
nIn the DTS NEO:6 mode
Information
Cinema : This is the mode for cinema source.
Music : This is the mode for music source.
Troubleshooting
•The “Music” mode is also effective for movie sources including a
lot of stereo music.
•The “Cinema” and “Music” modes can also be set by pressing
or
.
Cinema EQ
Specifications
OFF : “Cinema EQ” is not used.
Soften the treble range of ON : “Cinema EQ” is used.
movie sound tracks for better
understanding.
Dynamic
Range Low/Mid/High : These set the compression level.
Compression (D.Comp) OFF : Turn dynamic range compression off.
Compress dynamic range
The “D.Comp” indicator lights when playing DTS source that supports
(difference between loud
the “D.Comp” function.
and soft sounds).
Dynamic Range Control Auto : Dynamic range compression of Dolby TrueHD sources turns on and
off automatically.
(DRC)
Low/Mid/High : These set the compression level.
Compress dynamic range
OFF : Turn dynamic range compression off.
–10dB ~ 0dB
LFE
Adjust the low-frequency
For proper playback of the different program sources, we recommend
effects level (LFE).
setting to the values below.
•Dolby Digital sources : “0dB”
•DTS movie sources :
“0dB”
•DTS music sources :
“–10dB”
39
Remote control
operation buttons
Displaying the menu
:
Cancel the menu
: Moves the cursor (Up/Down/Left/Right)
: Decision the setting
: Return to previous menu
ENGLISH
Setting items
Center Image
Setting contents
Setting items
AFDM (Auto Flag Detect ON : Set.
OFF : Do not set.
Mode)
0.0 ~ 1.0 (0.3)
Surround Back
Sets the method of
generating of the surround
back channel.
nFor 2-channel sources
ON : The surround back channel is used.
OFF : No signal is played from the surround back channels.
nFor multi channel sources
Remote control
operation buttons
Displaying the menu
:
Cancel the menu
: Moves the cursor (Up/Down/Left/Right)
: Decision the setting
: Return to previous menu
40
Specifications
Troubleshooting
NOTE
This is valid when the “Pre Assign” setting (vpage 24) is set to “7.1channel surround back” or “6.1-channel surround back”, and when the
“S.Back” setting (vpage 25) is set to “Large” or “Small”.
Information
.
Remote Control
This can also be set by pressing
Playback
Set this to set the method of generating of the surround back channel
for sources that do not include surround back signals and when you
do not want to play the surround back signals included in the source.
Check the audio signals of the source being played before making this
setting.
OFF : No signal is played from the surround back channels.
MTRX ON : Generate and play the surround back signals from the
surround channel signals.
PLgx CINEMAz1 : Generate and play the surround back signals by
decoding the signals in the “Dolby Pro Logic gx Cinema” mode.
PLgx MUSICz2 : Generate and play the surround back signals by
decoding the signals in the “Dolby Pro Logic gx Music” mode.
ES MTRX : Generate and play the surround back signals from the
surround channel signals of the DTS source.
ES DSCRTz3 : Play the surround back signals included in the 6.1channel DTS source.
DSCRT ONz3 : Play the surround back signals included in the 7.1channel source.
z1 : This can be selected when “S.Back” in the “Speaker Config.”
settings (vpage 25) is set to “2ch”.
z2 : This can be selected when “S.Back” in the “Speaker Config.”
settings (vpage 25) is set to “2ch” or “1ch”.
z3 : When “AFDM” is set to “ON”, the surround back channel is played
with the AFDM function. When selected while “AFDM” is set to
“OFF”, the source’s surround back signals are played.
Settings
ON : Set.
Assign front L/R signal also OFF : Do not set.
to surround channels, for
wider sound.
0 ~ 6 (3)
Dimension
Shift sound image center
to front or rear, to adjust
playback balance.
0 ~ 7 (3)
Center Width
Assign center channel signal
to front left and right channels
for wider sound.
0ms ~ 300ms (30ms)
Delay Time
Adjust delay time to control
sound stage size.
1 ~ 15 (10)
Effect Level
Adjust the strength of the
Set to a lower level if the positioning and sense of phase of the
surround effect.
surround signals seems unnatural.
Small : Simulate acoustics of a small room.
Room Size
Determine size of acoustic Medium small : Simulate acoustics of a medium-small room.
Medium : Simulate acoustics of a medium room.
environment.
Medium large : Simulate acoustics of a medium-large room.
NOTE
Large : Simulate acoustics of a large room.
“Room Size” does not
indicate the size of the room
in which sources are played.
Detects the source’s surround
back channel signal and sets
the optimum surround mode
automatically.
Connections
Assign center channel signal
to front left and right channels
for wider sound.
Panorama
Setting contents
Getting Started
Adjusting the Sound Field Effect (Parameter)
ENGLISH
Getting Started
Adjusting the Sound Field Effect (Parameter)
Setting items
Setting contents
Making the MultEQ, Dynamic EQ and Dynamic Volume
settings (Audyssey Settings)
Front Height
Connections
ON : Use the front height channel.
Set whether or not to use OFF : Do not use the front height channel.
the front height channel.
This can also be set by pressing
.
Default settings are underlined.
Settings
Playback
•When the “Audyssey Auto Setup” (vpage 19) procedure is performed, the “MultEQ”, “Dynamic
EQ” and “Dynamic Volume” functions are enabled.
•Operating conditions for each function
•Dynamic EQ :
MultEQ
When “MultEQ” is set to “ON”
Dynamic EQ
•Dynamic Volume :
When “Dynamic EQ” is set to “ON”
Dynamic Volume
•Setting :
Setting
When “Dynamic Volume” is set to “ON”
Subwoofer
ON : The subwoofer is used.
Turn subwoofer output on OFF : The subwoofer is not used.
and off.
Yes : Reset to the defaults.
Default
Restores all the surround No : Do not reset to the defaults.
parameter settings to their
defaults.
NOTE
Remote Control
Adjusting the tone (Tone Control)
Default settings are underlined.
Setting items
Setting contents
Information
Troubleshooting
ON : Allow tone adjustment (treble, bass).
Tone Control
Sets the tone control function OFF : Playback without tone adjustment.
ON and OFF.
The tone cannot be adjusted when in the DIRECT mode.
This can be set when
“Dynamic EQ” (vpage
42) is set to “OFF”.
Bass
–6dB ~ +6dB (0dB)
Adjusts the low frequencies.
Specifications
This can be set when
“Tone Control” is set to
“ON”.
Treble
–6dB ~ +6dB (0dB)
Adjusts
the
frequencies.
high
If the speaker settings are changed after the “Audyssey Auto Setup” procedure is performed,
“MultEQ”, “Dynamic EQ” and “Dynamic Volume” functions cannot be selected and “Run Audyssey”
is displayed.
If this happens, either perform the “Audyssey Auto Setup” procedure again, or perform the “Restore”
operation (vpage 23) to restore the settings to as they were after the “Audyssey Auto Setup”
procedure was performed.
Setting items
Audyssey : Optimize frequency response of all speakers.
Corrects
the
frequency Audyssey Byp.L/R : Optimize frequency response of speakers except
response of the different front L and R speakers.
Audyssey Flat : Optimize frequency response of all speakers to flat
speakers.
response.
NOTE
Manual : Apply frequency response set with “Manual EQ” (vpage 42).
•“MultEQ” and “Manual OFF : The “MultEQ” equalizer cannot be used.
EQ” settings for which
• When “Audyssey”, “Audyssey Byp. L/R” or “Audyssey Flat” is
“Not Used” has been set at
“EQ Customize” (vpage
selected, “
” lights.
28) cannot be selected.
• After running Audyssey Auto Setup, if the Speaker Configuration,
•When using headphones,
Distance, Channel Level, and Crossover Frequency have changed
“MultEQ” is set to “OFF”.
without increasing the number of speakers measured, only “
”
This can be set when
“Tone Control” is set to
“ON”.
41
Remote control
operation buttons
Setting contents
MultEQ
Displaying the menu
:
Cancel the menu
: Moves the cursor (Up/Down/Left/Right)
lights.
•This can also be set by pressing
: Decision the setting
.
: Return to previous menu
ENGLISH
Setting items
Setting contents
Setting items
Dynamic EQ
This can be set when
“Dynamic EQ” (vpage
42) is set to “ON”.
Day : Low setting provides the least adjustments to the loudest and
softest of sounds.
Evening : Middle setting prevents loud and soft sounds from being much
louder and softer respectively than average sounds.
Midnight : High setting affects volume the most, causing all sounds to be
of equal loudness.
Dynamic EQ / Volume : OFF
Adjust tonal quality for each speaker using graphic equalizer
(Manual EQ)
“Off”
“OFF”
Default settings are underlined.
NOTE
Remote control
operation buttons
“Green”
“Green”
Displaying the menu
:
Cancel the menu
2.Select the frequency band to be adjusted.
63Hz / 125Hz / 250Hz / 500Hz / 1kHz / 2kHz / 4kHz / 8kHz /
16kHz
bWhen “L/R CH” or “Each CH” is selected, select the speaker to be
adjusted.
3.Adjust the level.
–20.0dB ~ +6.0dB (0dB)
Yes : Copy.
Base Curve Copy
Copy the MultEQ “Audyssey No : Do not copy.
Flat” correction curve.
“Base Curve Copy” is displayed after the Audyssey Auto Setup
procedure has been performed.
Yes : Reset to the defaults.
Default
Reset the “Manual EQ” No : Do not reset to the defaults.
settings to their defaults.
Dynamic EQ : ON / Volume : OFF
“Red”
: Moves the cursor (Up/Down/Left/Right)
: Decision the setting
: Return to previous menu
42
Specifications
Dynamic EQ / Volume : ON
1.Select speaker adjustment method.
All CH : Adjust tonal quality for all speakers together.
Adjust the tonal quality of
L/R CH : Adjust tonal quality for each L/R speaker pair.
the individual speakers.
Each CH : Adjust tonal quality for each speaker separately.
Troubleshooting
This can be set when
“Dynamic EQ” (vpage
42) is set to “ON”.
Setting contents
Adjust CH
Information
etting is enabled when “Dynamic EQ” is “ON”.
S
ON : Use Dynamic Volume. The Dynamic Volume effect will be at the level
Audyssey Dynamic Volume of the “Setting” (vpage 42)
solves the problem of OFF : Do not use Dynamic Volume.
large variations in volume
•When set to “ON”, “
” is displayed.
level between television
programs, commercials, and •When “MultEQ” is set to “OFF”, “Dynamic Volume” is automatically
set to “OFF”.
between the soft and loud
•This can also be set by pressing
.
passages of movies.
Dynamic Volume
Setting items
Remote Control
“Tone Control” is set to “OFF” when “Dynamic EQ” is set to “ON”.
Reference Level Offset : Audyssey Dynamic EQ takes the standard film
mixing level of 85 dB SPL during –20 dB FS input as its reference level.
However, since standardization is lacking outside the film industry, the
reference level of media contents may not be appropriate. In order to
view such contents, Reference Level Offset of Dynamic EQ has available
offsets of 5 dB, 10 dB and 15 dB.
• 0dB : Suitable for viewing movies.
• 5dB : Suitable for listening to classical music and other content mixed
at a high level.
• 10dB : Suitable for listening to jazz and other audio sources with a wide
dynamic range. Also suitable for viewing TV.
• 15dB : Suitable for listening to pop, rock music and other content with an
extremely wide dynamic range.
Playback
“Red”
“Green”
Set Dynamic Volume effect.
Settings
Dynamic EQ : ON/Volume : OFF
This can be set when the
“MultEQ” (vpage 41)
is set to anything other
than “OFF”.
Setting
Connections
ON : Use Dynamic EQ function.
Audyssey Dynamic EQ solves OFF : Do not use Dynamic EQ function.
the problem of deteriorating
•W
hen set to “ON”, “
” is displayed.
sound quality as volume is
•
W
hen
“MultEQ”
is
set
to
“OFF”
, “Dynamic EQ” is automatically set
decreased by taking into
to “OFF”
account human perception
•This can also be set by pressing
.
and room acoustics.
Setting contents
Getting Started
Adjusting the Sound Field Effect (Parameter)
ENGLISH
Getting Started
Adjusting the Sound Field Effect (Parameter)
Restoring compressed audio to nearly pre-compressed
conditions for playback (RESTORER)
Default settings are underlined.
Connections
Settings
•Such compressed audio formats as MP3, WMA (Windows Media Audio) and MPEG-4 AAC reduce the
amount of data by eliminating signal components that are hard for the human ear to hear. The RESTORER
function generates the signals eliminated upon compression, restoring the sound to conditions near
those of the original sound before compression. It also corrects the sense of volume of the bass to obtain
richer sound with compressed audio signals.
•This can be set with analog signals or when a PCM signal (fs = 44.1/48 kHz) is input.
Playback
Setting contents
Remote Control
OFF : Do not use RESTORER.
Mode1 (RESTORER 64) : Optimized mode for compressed sources with very weak highs.
Mode2 (RESTORER 96) : Apply suitable bass and treble boost for all compressed sources.
Mode3 (RESTORER HQ) : Optimized mode for compressed sources with normal highs.
•The default setting for “iPod” is “Mode3”. All others are set to “OFF”.
•When set to something other than “OFF”, “
” is displayed.
•This can also be set by pressing
Information
OFF
during playback.
Mode 1
(RESTORER 64)
Mode 2
(RESTORER 96)
Mode 3
(RESTORER HQ)
Troubleshooting
Specifications
Adjusting the audio delay time while watching the picture
(Audio Delay)
Default settings are underlined.
Checking the Status (Information)
Setting items
Status
Shows information
current settings.
Setting contents
Select Source / Surround Mode / Input Mode / Decode Mode / HDMI
about / Digital / Component / iPod Dock / Video Select / Source Level
You can also display current status on the main unit’s display each time
you press
.
Audio Input Signal
Surround Mode : The currently set surround mode is displayed.
about Signal : The input signal type is displayed.
fs : The input signal’s sampling frequency is displayed.
Format : The number of channels in the input signal (front, surround, LFE)
is displayed.
Offset : The dialogue normalization correction value is displayed.
Flag : This is displayed when inputting signals including a surround back
channel. “MATRIX” is displayed with Dolby Digital EX and DTS-ES Matrix
signals, “DISCRETE” with DTS-ES Discrete signals.
HDMI Signal Information
HDMI Information
Shows information about • Resolution / Color Space / Pixel Depth
HDMI input signals and HDMI Monitor Information
monitor.
• Interface / Suport Resolution
Analog/PCM / Digital 2ch / Digital 5.1ch / Multi CH
Auto Surround Mode
Shows information about
auto
surround
mode
settings.
Quick Select 1 / Quick Select 2 / Quick Select 3
Quick Select
Shows information about • Name / Input Source / Video Select / Volume Level / MultEQ /
Dynamic EQ / Dynamic Vol / Analog/PCM / Digital 2ch / Digital
quick select settings.
5.1ch / Multi CH
A1~G8
Preset Channel
Shows information about • TUNER
preset channels.
Shows information
audio input signals.
Setting contents
0ms ~ 200ms
43
•If you wish to adjust the “Audio Delay” while playing HDMI or component video signals, press u
to set “OSD” to “OFF”.This way the audio delay can be adjusted while watching the picture. (Press
the u again. The display switches to the display of the menu screen only.)
•This cannot be adjusted when playing in the DIRECT or STEREO mode (with “Front Speaker” set to
“Large”, “Tone Control” to “OFF” and “MultEQ” and “RESTORER” to “OFF”).
•When the Auto Lipsync Correction function is operating, you can set within the range 0 ~ 100 ms.
•Store “Audio Delay” for each input source.
Remote control
operation buttons
Displaying the menu
:
Cancel the menu
: Moves the cursor (Up/Down/Left/Right)
: Decision the setting
: Return to previous menu
ENGLISH
off step
zWhen you set “Output audio from amp” in the TV audio
nYou can switch audio output devices with a TV
nYou can adjust AVR-590 volume in the TV volume
adjustment operation
nYou can switch AVR-590 input source through
nWhen playing the player, the AVR-590 input
function switches to the function of that player
NOTE
Press
3
4
5
and display the time you want to set.
The “SLEEP” indicator on the display lights.
•The time switches as shown below each time
Sleep:OFF
Sleep:30min
Switch the television input to the HDMI connected to
the AVR-590.
Switch the AVR-590 input to the HDMI input source
and check if the picture from the player is ok.
When you turn the TV’s power to standby, check that
the power of the AVR-590 and player also goes on
standby.
If the HDMI control function does not operate properly, check the
following points.
•Is the TV or player compatible with the HDMI control function?
•Is the AVR-590 properly set?
•Is “HDMI Control” (vpage 27) set to “ON”?
•Is “Power Off Control” (vpage 27) set to “ON”?
•Are the HDMI control function settings of all equipment correct?
NOTE
Should any of the operations below be performed, the interlocking
function may be reset, in which case, repeat step’s 1 and 2.
• Menu “HDMI” (vpage 27) setting has changed.
• There is a change to the connection between the equipment and the
HDMI, or an increase in equipment.
Sleep:120min
is pressed.
Sleep:90min
Sleep:60min
•The time display turns off after about 5 seconds, and the
setting is activated.
•Once the set time has passed, the power is automatically set
to standby.
nTo cancel the sleep timer
Press
to set “OFF”.
•The “SLEEP” indicator on the display turns
off.
Playing the picture of a different
input source without changing
the currently playing sound
(Video Select Function)
Switch video input source while listening to audio signal.
Press
appears.
until the desired picture
bTo cancel, press
to select “SOURCE”.
NOTE
• It is not possible to select HDMI input signals.
• When playing HDMI video input signals, the analog video signal of
another input source cannot be selected for the HDMI video output.
• Input sources for which “Delete” is selected at “Source Delete”
(vpage 28) cannot be selected.
• Input sources for which “None” is selected at “Assign” (vpage 31)
cannot be selected.
44
Specifications
•When you power off AVR-590, the HDMI control function does not
operate.
•Some functions may not operate depending on the connected
TV or player. Check the owner’s manual of each device for details
beforehand.
•When “HDMI Control” is set to “ON”, it is not possible to assign an
HDMI connector to “TV” at “HDMI” (vpage 27).
Set “HDMI Control” (vpage 27) to “ON“.
bPlease refer to the owner’s manual as regards setting of connected
devices.
bCarry out Steps 1 and 2 should any of the equipment be
unplugged.
Troubleshooting
•To play the TV’s sound on the AVR-590, make optical digital
connections (vpage 13 “Connecting the TV”).
•To use this function, set “HDMI Control” (vpage 27) to “ON”.
connected by HDMI cable.
This function allows you to automatically set the power to
standby after the set amount of time has passed.
Information
linkage to TV input switching
Set the HDMI control function for all equipment
Remote Control
operation
HDMI cable.
Playback
output setup operation, you can switch the amp power
on.
Turn the power on for all the equipment connected by
Settings
nAVR-590 power off can be linked to the TV power
1
2
Connections
Setting the power to standby
after a certain amount of time
(Sleep Timer Function)
HDMI Control Function
When you make an HDMI connection with a TV or player
compatible with AVR-590 and HDMI control functions, you can
perform the following operations by setting the HDMI control
function of each device.
Getting Started
Convenient functions
ENGLISH
Getting Started
Adjust the volume of the
different speakers
You can adjust the channel level either according to the playback
sources or to suit your taste, as described below.
Connections
Adjust the volume of the different speakers
1
Press
.
Settings
0.0dB
0.0dB
0.0dB
0.0dB
SR
SBR
SBL
SL
0.0dB
0.0dB
0.0dB
0.0dB
Playback
Fader
FRONT : REAR
[
Remote Control
2
This function allows you to save all the settings shown in step
1. When frequently used settings are saved, they can easily be
set again the next time you want to use them. This function also
allows you to always enjoy the same playback environment.
•Three sets of settings can be saved.
Channel Volume
FL
C
FR
SW
Saving frequently used settings
(Quick Select Function)
]:CH Sel.
Press ui to select the speaker.
The speaker that can be set switches each time one of the
buttons is pressed.
Information
3
Press o p to adjust the volume.
1 Set the items below to the settings you want to save.
q Input source (vpage 34)
w Input Mode (vpage 32)
e Surround Mode (vpage 37)
r Audyssey Settings (MultEQ, Dynamic EQ, Dynamic
Volume) (vpage 41)
t Volume setting (vpage 34)
2
and
hold
the
desired
The current settings will be memorized.
“–12 dB” will change the setting to “OFF” (none).
GQuick Select DefaultsH
Troubleshooting
Quick Select 1
Quick Select 2
Quick Select 3
If headphones are plugged in, the headphones settings screen
appears.
Adjusting the volume of groups of speakers
(Fader Function)
Specifications
1
2
or i to select “Fader”, then select the item to
be adjusting using o or p.
Press the
want to call out are saved.
Use
Press o p to adjust the volume of the speakers.
•The fader function does not affect the subwoofer.
•The fader can be adjusted until the volume of the speaker adjusted
to the lowest value is –12 dB.
45
Input Source
DVD
SAT/CBL
VCR/iPod
Volume
–40 dB
–40 dB
–40 dB
Calling the settings out
This function lets you adjust (fade) the sound from all the front (Front
speaker / center speaker / Front Height speaker) or rear (Surround speaker /
Surround Back speaker) speakers at once.
at which the settings you
NOTE
Input sources stored with the quick select function cannot be selected
if they have been deleted at menu “Source Delete” (vpage 28). In
this case, store them again.
nNaming Quick Select settings
This function sets the settings (input mode, surround mode, HDMI
output mode, MultEQ, Dynamic EQ, Dynamic Volume, audio delay
etc.) last selected for the individual input sources.
“Quick Select Name” (vpage 29).
Last Function Memory
This stores the settings as they were directly before the standby mode
was set.
When the power is turned back on, the settings are restored to as they
were directly before the standby mode was set.
Backup Memory
The various settings are backed up for about 1 week, even if the power
is turned off or the power cord is disconnected.
until “Memory”
appears on the display.
bIn the case of a subwoofer, reducing the volume when it is at
Personal Memory Plus Function
The surround parameters, tone settings and the volumes of the
different speakers are stored for the individual surround modes.
Saving the settings
Press
Various memory functions
ENGLISH
Registering Preset Codes
n Cautions during operation
“RC SETUP START” appears on the display
and the remote control unit is set to the
preset code registration mode.
: TV
: Blu-ray disc player
“DEVICE” has been selected in step 1, press
2 When
the source select button for the device to be operated.
The remote control unit is set to the device mode for the device
to be operated. When the remote control transmitter is pointed
towards the AVR-590 at this time, the AVR-590’s input source
switches simultaneously.
: Digital video recorder
: Video deck
Satellite receiver
:
or cable TV
When registration is completed, “RC SETUP OK” appears on
the display.
b If the codes could not be registered, “RC SETUP NG” appears on
3
Operate the component.
6 7
Manual search
(fast-reverse / fast-forward)
8 9
Auto search
(cue)
uio p
ENTER
Cursor
Enter
Press and
hold
SEARCH
b For details, refer to the component’s operating instructions.
NOTE
Depending on the model and year of manufacture, this function cannot
be used for some models, even if they are of makes listed in the list
of preset codes.
RETURN
PAGE d f
Once
Page search
Browse/Remote mode switching
mode switching
z2
Return
Page up/down z1
z1 : This operation is possible when using a
DENON ASD-3N or ASD-3W Control Dock
for iPod.
z2 : This operation is possible when using a
DENON ASD-1R or ASD-11R Control Dock
for iPod.
the display. Try again.
store the codes of another component in the
3 Tomemory,
repeat steps 1 to 2.
b For details, refer to the component’s operating instructions.
•Some manufacturers use more than one type of remote control code.
Refer to the included list of preset codes to change the number and
verify correct operation.
•The preset memory can be set for one component only among the
following: DVD/CD and SAT/CBL.
46
Specifications
numbers are shown in the Preset
Code Table (vEnd of this
manual).
different source select button is pressed.
Power on / Standby z1
Play / Pause
Stop
Pause
MEMORY z1
Calling out the top menus z1
Troubleshooting
~
and input the
2 Press
3-digit number of the brand of
the component to be preset. The
b The remote control unit stays in the same device mode until a
ON/SOURCE
1
2
3
MEMORY
TOP MENU
Information
DVD player
:
or CD player
Remote Control
and
simultaneously for over 2
seconds.
TUNER/AMP : To operate a Tuner
: To operate a Blu-ray disc player, DVD player,
DEVICE
CD player, Digital video recorder, Video deck,
iPod, Satellite receiver or cable TV
MAIN/TV : To operate a TV
Operation
mode setting
Playback
the source select button (see
1 Press
below) for the device to be registered
to the device to be operated.
iPod
Settings
When registering a preset code, point the remote control transmitter
toward the AVR-590. The status of the registration operation is
displayed on the AVR-590.
1 Switch
Operating Registered Devices
Connections
DENON and other makes of components can be operated by
setting the preset memory.
Operating Registered Devices
Getting Started
Operating the Connected Devices by Remote Control Unit
ENGLISH
Getting Started
Operating Registered Devices
TV
Blu-ray Disc / DVD Player
Connections
Operation
mode setting
CD Player
Operation
mode setting
or
Operation
mode setting
OFF
Settings
ON/SOURCE
TV/POWER
1
3
2
Playback
6 7
CHANNEL + –
TV INPUT
Remote Control
VOLUME df
Information
MUTE
MENU
uio p
ENTER
SETUP
RETURN
Default setting
(Preset code)
Special Remarks
Power on / Standby
Power on / Standby z1
Play z2
Pause z2
Stop z2
Manual search z2
(fast-reverse / fast-forward)
Switch channels (+, –)
Switching the input z1
SKIP +
Standby
Power on or Power on / Standby
Play
Stop
Pause
BD Player
DVD Player
–
Disc skip
Troubleshooting
uio p
ENTER
SETUP
RETURN
Manual search
(fast-reverse / fast-forward)
Auto search (cue)
BD Player
DVD Player
Popup menus
Menus
Cursor operation
Enter setting
Setup
Return
SONY (374)
TOP MENU
Top menus
q
Default setting
(Preset code)
Special Remarks
d : TV Volume (+)
f : TV Volume (–)
TV MUTE
Calling out the menus
Cursor operation
Enter setting
Setup
Return
Specifications
*1 : This can be operated even when the
operation mode is set to something
other than “TV”.
*2 : When the punch through function
(vpage 48) is set, this functions
as the button for the device for which
punch through is set.
【Special Remarks】
q Only one device can be set in the preset memory for each mode.
When a new preset code is registered, the existing code is automatically erased.
w For some brands, the DVD remote control buttons may have different function names.
Check beforehand.
47
OFF
ON/SOURCE
1
2
3
6 7
8 9
MENU
BD Player
DENON (111)
DVD Player
DENON (111)
q, w
ON/SOURCE
1
2
3
SKIP +
6 7
8 9
Standby
Power on or Power on /
Standby
Play
Stop
Pause
Disc skip +
Manual search
(fast-reverse / fast-forward)
Auto search (cue)
Default setting
(Preset code)
–
Special Remarks
q
ENGLISH
Satellite receiver/Cable TV
6 7
Video Deck
JVC (001)
HITACHI (111)
q, w
CHANNEL + –
uio p
ENTER
MENU
SETUP
RETURN
Default setting
(Preset code)
Special Remarks
(fast-reverse / fast-forward)
Switch channels (+, –)
Cursor operation
Enter setting
Guide menus
Setup
Return
Satellite
Cable TV
Receiver
Direc TV (095)
–
q
or
1 Press
for which the
for the device
punch through
function is to be registered and
simultaneously for over 2 seconds.
“RC SETUP START” appears on the
display.
the source select button for
2 Press
the device to be assigned.
When registration is completed, “RC
SETUP OK” appears on the display.
b If the codes could not be registered, “RC
SETUP NG” appears on the display. Try
again.
NOTE
If the “TV” or “SAT/CBL” preset code is changed after setting the
punch through function, the punch through setting is canceled.
48
Specifications
【Special Remarks】
q Only one device can be set in the preset memory for each mode.
When a new preset code is registered, the existing code is automatically erased.
w For some brands, the DVD remote control buttons may have different function names.
Check beforehand.
When registering a punch through function, point the remote control
transmitter toward the AVR-590. The status of the registration operation
is displayed on the AVR-590.
Troubleshooting
* : When the punch through function
(vpage 48) is set, this functions as the
button for the device for which punch
through is set.
n Cautions during operation
Information
Special Remarks
Digital Video
Recorder
6 7
Power on / Standby
Playz
Pausez
Stopz
Manual search z
Remote Control
Default setting
(Preset code)
ON/SOURCE
1
3
2
When the remote control unit´s device mode is set to “TV” or “SAT/
CBL”, the next “TUNER”, “DVD”, “HDP”, “iPod”, “DVR” or “VCR”
operation can be performed without switching the remote control
unit's device mode.
•One device each can be assigned to the “TV” and “SAT/CBL”
device modes.
•Assignable buttons
Playback
CHANNEL + –
MENU
uio p
ENTER
SETUP
RETURN
Power on / Standby
Play
Stop
Pause
Manual search
(fast-reverse / fast-forward)
Switch channels (+, –)
Menus
Cursor operation
Enter setting
Setup
Return
Operation
mode setting
Settings
ON/SOURCE
1
2
3
or
Connections
Operation
mode
setting
Assigning buttons that are Not
Used to Operate Other Devices
(Punch Through Function)
Getting Started
Operating Registered Devices
Digital Video Recorder / Video Deck
ENGLISH
Getting Started
Other Information
Surround
Settings
Dolby Digital
Dolby Pro Logic gx
DTS Digital Surround
Dolby Digital is a multichannel digital signal format developed by Dolby
Laboratories.
A total of 5.1-channels are played: 3 front channels (“FL” , “FR” and
“C”), 2 surround channels (“SL” and “SR”) and the “LFE” channel for
low frequencies.
Because of this, there is no crosstalk between channels and a realistic
sound field with a “three-dimensional” feeling (sense of distance,
movement and positioning) is achieved.
A real, overpowering sense of presence is achieved when playing
movie sources in AV rooms as well.
Dolby Pro Logic gx is a further improved version of the Dolby Pro Logic
g matrix decoding technology.
Audio signals recorded in 2-channels are decoded to achieve a natural
sound with up to 7.1-channels.
There are 3 modes: “Music” suited for playing music, “Cinema”
suited for playing movies, and “Game” which is optimized for playing
games.
DTS Digital Surround is the standard digital surround format of DTS,
Inc., compatible with a sampling frequency of 44.1 or 48 kHz and up
to 5.1-channels of digital discrete surround sound.
Playback
Connections
The AVR-590 is equipped with a digital signal processing circuit that lets you play program sources in the surround mode to achieve the same sense of presence as in a movie theater.
Dolby Surround
Remote Control
Information
Dolby Digital Plus
Troubleshooting
Dolby Digital Plus is an improved Dolby Digital signal format that is
compatible with up to 7.1-channels of discrete digital sound and also
improves sound quality thanks to extra data bit rate performance. It
is upwardly compatible with conventional Dolby Digital, so it offers
greater flexibility in response to the source signal and the conditions
of the playback equipment.
Dolby TrueHD
Specifications
Dolby TrueHD is a high definition audio technology developed by Dolby
Laboratories, using lossless coding technology to faithfully reproduce
the sound of the studio master.
This format is compatible with a maximum sampling frequency of 96
kHz and up to 7.1-channels, so it is used for applications particularly
prioritizing sound quality.
Dolby Pro Logic g
Dolby Pro Logic g is a matrix decoding technology developed by Dolby
Laboratories.
Regular music such as that on CDs is encoded into 5-channels to
achieve an excellent surround effect.
The surround channel signals are converted into stereo and full band
signals (with a frequency response of 20 Hz to 20 kHz or greater)
to create a “three-dimensional” sound image offering a rich sense of
presence for all stereo sources.
49
DTS Surround
Dolby Digital EX
Dolby Digital EX is a 6.1-channel surround format proposed by Dolby
Laboratories that allows users to enjoy in their homes the “DOLBY
DIGITAL SURROUND EX” audio format jointly developed by Dolby
Laboratories and Lucas Films.
The 6.1 channels of sound, including surround back channels, provide
improved sound positioning and expression of space.
Dolby Pro Logic gz
Dolby Pro Logic gz introduces a new dimension to Home Entertainment
through the addition of a pair of front height channels. Compatible with
stereo, 5.1 and 7.1 content, Dolby Pro Logic gz provides enhanced
spaciousness, depth and dimension to movies, concert video and
videogame playback while maintaining the full integrity of the source
mix.
Dolby Pro Logic gz identifies and decodes spatial cues that occur
naturally in all content, directing this information to the front height
channels, complementing the performance of left and right surround
sound speakers. Content that is encoded with Dolby Pro Logic
gz height channel information can be even more revealing, with
perceptually discrete height channel information bringing an exciting
new dimension to home entertainment.Dolby Pro Logic gz, with front
height channels is also an ideal alternative for households that cannot
support the placement of back surround speakers of a typical 7.1
channel system but may have bookshelf space available to support the
addition of height speakers.
Manufactured under license from Dolby Laboratories.
“Dolby”, “Pro Logic” and the double-D symbol are trademarks of
Dolby Laboratories.
DTS-HD High Resolution Audio
DTS-HD High Resolution Audio is an improved version of the
conventional DTS, DTS-ES and DTS 96/24 signals formats, compatible
with sampling frequencies of 96 or 48 kHz and up to 7.1-channels
of discrete digital sound. High data bit rate performance provides
high quality sound. This format is fully compatible with conventional
products, including conventional DTS digital surround 5.1-channel
data.
DTS-HD Master Audio
DTS-HD Master Audio is DTS, Inc’s lossless audio format compatible
with up to 96 kHz/7.1-channels. The lossless audio coding technology
faithfully reproduces the sound of the studio master. It is fully
compatible with conventional products, including conventional DTS
digital surround 5.1-channel data.
DTS-ES™ Discrete 6.1
DTS-ES™ Discrete 6.1 is a 6.1-channel discrete digital audio format
adding a surround back (SB) channel to the DTS digital surround sound.
Decoding of conventional 5.1-channel audio signals is also possible
according to the decoder.
DTS-ES™ Matrix 6.1
DTS-ES™ Matrix 6.1 is a 6.1-channel discrete digital audio format
inserting a surround back (SB) channel to the DTS digital surround
sound through matrix encoding. Decoding of conventional 5.1-channel
audio signals is also possible according to the decoder.
DTS NEO:6™ Surround
DTS NEO:6™ is a matrix decoding technology for achieving 6.1channel surround playback with 2-channel sources. It includes “DTS
NEO:6 Cinema” suited for playing movies and “DTS NEO:6 Music”
uited for playing music.
ENGLISH
Audyssey Dynamic Volume™
DTS 96/24 is a digital audio format enabling high sound quality
playback in 5.1-channels with a sampling frequency of 96 kHz and 24
bit quantization on DVD-Video.
Audyssey Dynamic Volume solves the problem of large variations in
volume level between television programs, commercials, and between
the soft and loud passages of movies.
Audyssey Dynamic EQ is integrated into Dynamic Volume so that as
the playback volume is adjusted automatically, the perceived bass
response, tonal balance, surround impression, and dialog clarity
remain the same.
Manufactured under license from Audyssey Laboratories. U.S.
and foreign patents pending. Audyssey MultEQ® is a registered
trademark of Audyssey Laboratories. Audyssey Dynamic EQ™ is a
trademark of Audyssey Laboratories. Audyssey Dynamic Volume™
is a trademark of Audyssey Laboratories.
Playback
Audyssey
Settings
Manufactured under license under U.S. Patent #’s: 5,451,942;
5,956,674; 5,974,380; 5,978,762; 6,226,616; 6,487,535; 7,212,872;
7,333,929; 7,392,195; 7,272,567 & other U.S. and worldwide patents
issued & pending. DTS is a registered trademark and the DTS
logos, Symbol, DTS-HD and DTS-HD Master Audio are trademarks
of DTS, Inc.© 1996-2008 DTS, Inc. All Rights Reserved.
Connections
DTS 96/24
Getting Started
Surround
Remote Control
Audyssey MultEQ®
Information
Audyssey MultEQ is a room equalization solution that calibrates any
audio system so that it can achieve optimum performance for every
listener in a large listening area. Based on several room measurements,
MultEQ calculates an equalization solution that corrects for both
time and frequency response problems in the listening area and also
performs a fully automated surround system setup.
Audyssey Dynamic EQ™
Troubleshooting
Audyssey Dynamic EQ solves the problem of deteriorating sound
quality as volume is decreased by taking into account human perception
and room acoustics. Audyssey Dynamic EQ works in tandem with
Audyssey MultEQ to provide well-balanced sound for every listener
at any volume level.
Specifications
50
ENGLISH
Getting Started
Surround
Surround Modes and Parameters
Signals and adjustability in the different modes
Parameter (default values are shown in parentheses)
Center
DIRECT
S
D
D
D
A
D
S (OFF)
S (0dB)
A
A
MULTI CH DIRECT
S
D
D
D
A
D
A
S (0dB)
S (ON)
S
STEREO
S
A
A
A
A
D
S (OFF)
S (0dB)
A
A
MULTI CH IN
S
D
D
D
A
D
A
S (0dB)
S (ON)
S
DOLBY PRO LOGIC gx
S
D
D
D
A
D
S (OFF)
A
A
S
S (NOTE1) S (Cinema)
DOLBY PRO LOGIC g
S
D
D
A
A
D
S (OFF)
A
A
S
DTS NEO:6
S
D
D
D
A
D
S (OFF)
A
A
S
DOLBY PRO LOGIC gz
S
D
D
A
D
D
S (OFF)
A
A
A
S (OFF)
DOLBY DIGITAL
S
D
D
D
D
D
S (OFF)
S (0dB)
S (ON)
S
DOLBY DIGITAL Plus
S
D
D
D
D
D
S (OFF)
S (0dB)
S (ON)
DOLBY TrueHD
S
D
D
D
D
D
S (OFF)
S (0dB)
DTS SURROUND
S
D
D
D
D
D
S (OFF)
DTS 96/24
S
D
D
D
D
D
S (OFF)
DTS-HD
S
D
D
D
D
D
5CH/7CH STEREO
S
D
D
D
D
ROCK ARENA
S
D
D
D
JAZZ CLUB
S
D
D
MONO MOVIE
S
D
VIDEO GAME
S
MATRIX
VIRTUAL
Settings
Front L/R
Surround
L/R
Remote Control
Surround mode
Playback
Connections
Channel output
Surround Front Height
Su­b­­­­woofer
Back L/R
L/R
LFE
AFDM
Information
Troubleshooting
Room Size
Effect
Delay time
Subwoofer
A
A
A
A
A
S
A
A
A
A
A
A
A
A
A
A
A
A
A
S (Auto)
A
A
A
A
A
A
A
A
A
A
A
S (Auto)
S (NOTE2) S (Cinema)
A
A
A
A
S (Auto)
S (NOTE1) S (Cinema)
A
A
A
A
A
A
A
A
A
A
A
S (OFF)
A
A
A
A
A
A
S
S (OFF)
A
A
A
A
A
A
S (ON)
S
S (OFF)
A
A
A
A
A
S (Auto)
S (0dB)
S (ON)
S
S (OFF)
A
A
A
A
A
A
S (0dB)
S (ON)
S
S (OFF)
A
A
A
A
A
A
S (OFF)
S (0dB)
S (ON)
S
S (OFF)
A
A
A
A
A
A
D
S (OFF)
S (0dB)
A
S
A
A
A
A
A
A
A
D
D
S (OFF)
S (0dB)
A
S
A
A
S (Medium)
S (10)
A
A
A
D
D
D
S (OFF)
S (0dB)
A
S
A
A
S (Medium)
S (10)
A
A
A
D
D
D
D
S (OFF)
S (0dB)
A
S
A
A
S (Medium)
S (10)
A
A
A
D
D
D
D
D
S (OFF)
S (0dB)
A
S
A
A
S (Medium)
S (10)
A
A
A
S
D
D
D
D
D
S (OFF)
S (0dB)
A
S
A
A
A
A
S (30 ms)
A
A
S
A
A
A
A
D
S (OFF)
S ( 0dB)
A
A
A
A
A
A
A
A
A
z1
z2
z1
SB CH Out Cinema EQ.
DRC
Mode
S: Signal / Adjustable
A : No signal / Not adjustable
D:Turned on or off by speaker configuration setting
Specifications
51
D. Comp
S: Signal / Adjustable
A : No signal / Not adjustable
NOTE1 :This parameter is available when the menu “Mode” (vpage 39) is set to “Cinema”.
NOTE2 :T his parameter is available when the menu “Mode” (vpage 39) is set to “Cinema” or “PL”.
NOTE:
z1 :When playing Dolby Digital and DTS signals.
z2 :When playing Dolby Digital, DTS and Linear PCM (multi ch).
z3 :When playing Dolby TrueHD signal.
z3
S (Auto)
ENGLISH
Signals and adjustability in the different modes
Parameter (default values are shown in parentheses)
Surround mode
PRO LOGIC g/gx MUSIC mode only
NEO:6 MUSIC
mode only
MultEQ
Dynamic EQ
(NOTE5)
Dynamic
Volume
(NOTE6)
RESTORER
(NOTE7)
A
Panorama
Dimension
C. Width
Center Image
DIRECT
A
A
A
A
A
A
A
A
MULTI CH DIRECT
A
A
A
A
A
A
A
A
A
STEREO
A
A
A
A
S (0dB)
S (OFF)
S (OFF)
S (OFF)
S
A
A
A
A
S (0dB)
S (OFF)
S (OFF)
S (OFF)
A
DOLBY PRO LOGIC gx
S (OFF)
S (3)
S (3)
A
S (0dB)
S (OFF)
S (OFF)
S (OFF)
S
DOLBY PRO LOGIC g
S (0dB)
S (OFF)
S (OFF)
S (OFF)
S
S (0.3)
S (0dB)
S (OFF)
S (OFF)
S (OFF)
S
DOLBY PRO LOGIC gz
A
A
A
A
S (0dB)
S (OFF)
S (OFF)
S (OFF)
A
DOLBY DIGITAL
A
A
A
A
S (0dB)
S (OFF)
S (OFF)
S (OFF)
A
DOLBY DIGITAL Plus
A
A
A
A
S (0dB)
S (OFF)
S (OFF)
S (OFF)
A
DOLBY TrueHD
A
A
A
A
S (0dB)
S (OFF)
S (OFF)
S (OFF)
A
DTS SURROUND
A
A
A
A
S (0dB)
S (OFF)
S (OFF)
S (OFF)
A
DTS-96/24
A
A
A
A
S (0dB)
S (OFF)
S (OFF)
S (OFF)
A
DTS-HD
A
A
A
A
S (0dB)
S (OFF)
S (OFF)
S (OFF)
A
5CH/7CH STEREO
A
A
A
A
S (0dB)
S (OFF)
S (OFF)
S (OFF)
S
ROCK ARENA
A
A
A
A
S (NOTE3)
S (OFF)
S (OFF)
S (OFF)
S
JAZZ CLUB
A
A
A
A
S (0dB)
S (OFF)
S (OFF)
S (OFF)
S
MONO MOVIE
A
A
A
A
S (0dB)
S (OFF)
S (OFF)
S (OFF)
S
VIDEO GAME
A
A
A
A
S (0dB)
S (OFF)
S (OFF)
S (OFF)
S
MATRIX
A
A
A
A
S (0dB)
S (OFF)
S (OFF)
S (OFF)
S
VIRTUAL
A
A
A
A
S (0dB)
S (OFF)
S (OFF)
S (OFF)
S
Troubleshooting
A
A
Information
S (3)
A
Remote Control
S (3)
A
Playback
S (OFF)
DTS NEO:6
Settings
MULTI CH IN
Connections
Tone
(NOTE4)
Getting Started
Surround
Specifications
S: Adjustable
A : Not adjustable
NOTE3 :BASS +6 dB, TREBLE +4 dB
NOTE4 :Cannot be set when the “Dynamic EQ” (vpage 42) setting is “ON”.
NOTE5 :Cannot be set when the “MultEQ” (vpage 41) setting is “OFF”.
NOTE6 :Cannot be set when the “Dynamic EQ” (vpage 42) setting is “OFF”.
NOTE7 :“RESTORER” can be set for analog or PCM 48 k or 44.1 k input signals.
52
ENGLISH
Getting Started
Surround
Differences in Surround Mode Names Depending on the Input Signals
Input signals
Button
PCM
Connections
Surround mode
Note
Linear
ANALOG
PCM
(multi ch)
DTS-HD
Linear
PCM
(2ch)
DTS-HD
Master
Audio
DTS
DTS-HD
High
Resolution
Audio
DTS ES
DTS ES
DSCRT
MTRX
(With Flag) (With Flag)
DOLBY
DTS
(5.1ch)
DTS
96/24
DOLBY DIGITAL
DOLBY
DOLBY
DIGITAL
TrueHD
Plus
DOLBY
DIGITAL
EX (With
Flag)
DOLBY
DOLBY
DIGITAL EX
DIGITAL
(With no
(5.1/5/4ch)
Flag)
DOLBY
DIGITAL
(4/3ch)
DOLBY
DIGITAL
(2ch)
STANDARD
Settings
DTS SURROUND
DTS-HD MSTR
A
A
A
F
A
A
A
A
A
A
A
A
A
A
A
A
DTS-HD HI RES
A
A
A
A
F
A
A
A
A
A
A
A
A
A
A
A
Playback
DTS ES DSCRT6.1
z1 z3
A
A
A
A
A
F D
A
A
A
A
A
A
A
A
A
A
DTS ES MTRX6.1
z1 z3
A
A
A
A
A
A
F D
A
A
A
A
A
A
A
A
A
DTS SURROUND
A
A
A
A
A
S
S
F
A
A
A
A
A
A
A
A
DTS 96/24
A
A
A
A
A
A
A
A
F
A
A
A
A
A
A
A
Remote Control
Information
DTS (–HD) + PLgx CINEMA
z2 z3
A
A
A
S
S
S
S
S
S
A
A
A
A
A
A
A
DTS (–HD) + PLgx MUSIC
z1 z3
A
A
A
S
S
S
S
S
S
A
A
A
A
A
A
A
DTS (–HD) + PLgz
z1 z4
A
A
A
S
S
S
S
S
S
A
A
A
A
A
A
A
DTS (–HD) + NEO:6
z1 z3
A
A
A
S
S
A
S
S
S
A
A
A
A
A
A
A
DTS NEO:6 CINEMA
S
A
S
A
A
A
A
A
A
A
A
A
A
A
A
S
DTS NEO:6 MUSIC
S
A
S
A
A
A
A
A
A
A
A
A
A
A
A
S
DOLBY TrueHD
A
A
A
A
A
A
A
A
A
F
A
A
A
A
A
A
DOLBY DIGITAL+
A
A
A
A
A
A
A
A
A
A
F
A
A
A
A
A
DOLBY SURROUND
Troubleshooting
DOLBY DIGITAL EX
z1 z3
A
A
A
A
A
A
A
A
A
A
A
S
S
S
S
A
DOLBY (D+) (HD) +EX
z1 z3
A
A
A
A
A
A
A
A
A
S
S
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
S
F
F
F
A
DOLBY DIGITAL
Specifications
DOLBY (D) (D+) (HD) +PLgx CINEMA
z2 z3
A
A
A
A
A
A
A
A
A
S
S
F D
S
S
S
A
DOLBY (D) (D+) (HD) +PLgx MUSIC
z1 z3
A
A
A
A
A
A
A
A
A
S
S
S
S
S
S
A
DOLBY (D) (D+) (HD) +PLgz
z1 z4
A
A
A
A
A
A
A
A
A
S
S
S
S
S
S
A
DOLBY PRO LOGIC gx CINEMA
z3
S
A
S
A
A
A
A
A
A
A
A
A
A
A
A
S
DOLBY PRO LOGIC gx MUSIC
z3
S
A
S
A
A
A
A
A
A
A
A
A
A
A
A
S
DOLBY PRO LOGIC gx GAME
z3
S
A
S
A
A
A
A
A
A
A
A
A
A
A
A
S
DOLBY PRO LOGIC gz
z4
S
A
S
A
A
A
A
A
A
A
A
A
A
A
A
S
DOLBY PRO LOGIC g CINEMA
S
A
S
A
A
A
A
A
A
A
A
A
A
A
A
S
DOLBY PRO LOGIC g MUSIC
S
A
S
A
A
A
A
A
A
A
A
A
A
A
A
S
DOLBY PRO LOGIC g GAME
S
A
S
A
A
A
A
A
A
A
A
A
A
A
A
S
DOLBY PRO LOGIC
S
A
S
A
A
A
A
A
A
A
A
A
A
A
A
S
NOTE:
z1: This mode is not available when the surround back speaker setup is set to “None”.
z2: This mode is not available when the surround back speaker setup is set to “1ch” or “None”.
z3: Can be set when “Pre Assign” is set to “Normal”
.
z4: Not selectable when “Pre Assign” is set to anything other than “Front Height”
.
53
F : Mode selectable in initial status
D : Mode fixed when “AFDM” is “ON”
S : Selectable mode
A : Non-selectable mode
ENGLISH
Input signals
Button
PCM
Surround mode
Note
DTS
Linear
PCM
(2ch)
DTS-HD
Master
Audio
DTS-HD
High
Resolution
Audio
DTS ES
DTS ES
DSCRT
MTRX
(With Flag) (With Flag)
DOLBY
DTS
(5.1ch)
DTS
96/24
DOLBY DIGITAL
DOLBY
DOLBY
DIGITAL
TrueHD
Plus
DOLBY
DIGITAL
EX (With
Flag)
DOLBY
DOLBY
DIGITAL
DIGITAL
EX (With
(5.1/5/4ch)
no Flag)
DOLBY
DIGITAL
(4/3ch)
DOLBY
DIGITAL
(2ch)
STANDARD
MULTI CH IN
MULTI CH IN
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
S
A
A
A
A
A
A
A
A
A
A
A
A
A
A
MULTI IN + PLgx MUSIC
z1 z3
A
S
A
A
A
A
A
A
A
A
A
A
A
A
A
A
MULTI IN + PLgz
z1 z5
A
S
A
A
A
A
A
A
A
A
A
A
A
A
A
A
MULTI IN + Dolby EX
z1 z3
A
S
A
A
A
A
A
A
A
A
A
A
A
A
A
A
z3
A
F D (7.1)
A
A
A
A
A
A
A
A
A
A
A
A
A
A
MULTI CH IN 7.1
Playback
F
z2 z3
Settings
A
MULTI IN + PLgx CINEMA
DIRECT
S
A
S
S
S
S
S
S
S
S
S
S
S
S
S
S
MULTI CH DIRECT
A
S
A
A
A
A
A
A
A
A
A
A
A
A
A
A
z2 z3
A
S
A
A
A
A
A
A
A
A
A
A
A
A
A
A
M DIRECT + PLgx MUSIC
z1z3
A
S
A
A
A
A
A
A
A
A
A
A
A
A
A
A
M DIRECT + PLgz
z1z5
A
S
A
A
A
A
A
A
A
A
A
A
A
A
A
A
M DIRECT + Dolby EX
z1 z3
A
S
A
A
A
A
A
A
A
A
A
A
A
A
A
A
z3
A
S (7.1)
A
A
A
A
A
A
A
A
A
A
A
A
A
A
z4
M DIRECT 7.1
Information
M DIRECT + PLgx CINEMA
Remote Control
DIRECT
DSP SIMULATION
5CH/7CH STEREO
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
JAZZ CLUB
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
MONO MOVIE
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
VIDEO GAME
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
MATRIX
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
VIRTUAL
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
F
S
F
S
S
S
S
S
S
S
S
S
S
S
S
S
Troubleshooting
S
ROCK ARENA
STEREO
NOTE :
z1: This mode is not available when the surround back speaker setup is set to “None”.
z2: This mode is not available when the surround back speaker setup is set to “1ch” or “None”.
z3: Can be set when “Pre Assign” is set to “Normal”
.
z4: If the surround back speaker setup is set to “None”, then “5CH STEREO” is displayed.
z5: Not selectable when “Pre Assign” is set to anything other than “Front Height”
.
Specifications
STEREO
Connections
Linear
ANALOG
PCM
(multi ch)
DTS-HD
Getting Started
Surround
F : Mode selectable in initial status
D : Mode fixed when “AFDM” is “ON”
S : Selectable mode
A : Non-selectable mode
54
ENGLISH
Getting Started
Troubleshooting
Connections
Settings
If a problem should arise, first check the following:
1. Are the connections correct?
2. Is the set being operated as described in the owner’s manual?
3. Are the other components operating properly?
If this unit does not operate properly, check the items listed in the table below. Should the problem persist,
there may be a malfunction.
In this case, disconnect the power immediately and contact your store of purchase.
GGeneralH
Playback
Remote Control
Symptom
Set does not
operate properly.
Power does not
turn on, or turns
off directly after it
was turned on.
No sound is
produced from
speakers.
Cause
Countermeasure
•External noise or interference is •Reset the microprocessor.
causing the set to malfunction.
•Connection of the power cord is •Check the insertion of the power
faulty.
cord plug.
Information
Troubleshooting
•Connection with the input
devices or connection of the
speaker cables is faulty.
•Device you want to play and set
input source do not match.
•Master volume is turned too
low.
•Mute mode is set.
•Headphones are connected.
•No digital signals are being
input.
•Check the connections.
Specifications
•Select an appropriate input
source.
•Adjust the master volume to an
appropriate level.
•Cancel the mute mode.
•Disconnect the headphones.
•Select an input source for which
the digital input setting has been
made.
•The connectors to which the •Set the input mode.
digital inputs are assigned and
the settable input modes do not
match.
Display is off.
•The “Display” setting is set to •Set to something other than
“OFF”.
“OFF”.
“DOLBY DIGITAL” •Blu-ray Disc player / DVD player’s •Check the Blu-ray Disc player /
indicator does not
digital audio output setting is not DVD player’s audio output setting.
appear on display.
proper.
For details, read the Blu-ray Disc
player / DVD player’s operating
instructions.
55
Page
57
16
11
34
34
37
37
31
32
37
–
Symptom
Power switches
off suddenly while
you are using
the AVR-590, the
power indicator
will flash in red
at intervals of
approximately 2
seconds.
Power switches
off suddenly while
you are using
the AVR-590, the
power indicator
will flash red
at intervals of
approximately 0.5
seconds.
Even applying
power, the power
display flashes
red at intervals of
approximately 0.5
seconds.
Set does not work
properly when
remote control
unit operated.
Cause
Countermeasure
•The protection circuit will be •Please switch off power at once,
activated depending upon the and re-apply the power after
temperature rise in the internal the body temperature has fallen
parts of the unit.
sufficiently.
•Please re-install AVR-590 in a
place having good ventilation.
Page
3
•Use speakers having impedance •Please use speakers which have
less than that specified.
the specified impedance.
•If speaker cable core wires touch •Unplug the power cord, then
each other or the core wires after twisting the core wires
become disconnected from their together tightly again, or effecting
terminals, the protection circuit termination treatments etc,
will be activated in the event of please reconnect once again.
core wires coming into contact
with the AVR-590 rear panel.
•The AVR-590 amplifier circuit has •Switch off the power and please
failed.
contact the DENON service
adviser.
12
•Batteries are worn.
•You are operating outside of the
specified range.
•Obstacle between main unit and
remote control unit.
•The batteries are not inserted in
the proper direction, as indicated
by the polarity marks in the
battery compartment.
•The set’s remote control sensor
is exposed to strong light (direct
sunlight, inverter type fluorescent
bulb light, etc.).
•The device selection switch is
not set to the proper position.
•Replace with new batteries.
•Operate within the specified
range.
•Remove the obstacle.
3
3
•Insert the batteries in the
proper direction, following the
polarity marks in the battery
compartment.
•Move the set to a place in which
the remote control sensor will
not be exposed to strong light.
3
•Set the device selection switch
to the proper position, according
to the purpose for operating the
switch.
•Perform the remote control unit •Before operating the remote
device mode setting operation.
control unit, set the device mode
for the device to be operated.
46
–
12
–
3
3
46
ENGLISH
38, 39
27
GVideoH
Symptom
No picture
appears.
39
37
–
24
Picture cannot be
recorded.
Cause
•The connections between the
AVR-590 and monitor are faulty.
•The monitor’s input setting is
wrong.
•The player is connected using
the component input connectors,
the monitor is connected
using the video (yellow) output
connectors.
•Input source does not match
recorder’s video connection
connector (video).
11
45
DVDs cannot be
copied on a DVR.
–
–
–
The menu screen
and status
indicators are not
displayed.
32
27
•“OFF”����������������������
is displayed for the
status.
•The main volume display is
“OFF”.
•The display during tuner operation
is “OFF”.
•The display during iPod operation
is “OFF”.
Countermeasure
•Check the connections.
Page
13 ~ 16
•Set properly.
–
•High definition (1080i/720p) and
progressive (480p/576p) video
signals are not down-converted.
Set the player to interlace
(480i/576i) signals.
•The video conversion function
does not work for the REC
OUT connectors. Match the
input source and recorder
connections.
•This is not a malfunction. Most
movie software includes copy
prevention signals and cannot be
copied.
•When
viewing
HDMI
or
component video signals via the
AVR-590, the on-screen display
appears when the MENU button
on the main unit or the MENU
button on the main remote
control unit.
•Set “Manual Setup” – “Option
Setup” – “On-Screen Display”
– “Text” to “ON”.
•Set “Manual Setup” – “Option
Setup” – “On-Screen Display”
– “Master Volume” to “Top” or
“Bottom”.
•Set when “Manual Setup”
– “On-Screen Display” – “Tuner
Information” is not “OFF”.
•Set when “Manual Setup”
– “On-Screen Display” – “ iPod
Information” is not “OFF”.
–
15
–
9
Specifications
•The “Manual Setup” – “HDMI • Set to “TV”.
Setup” – “HDMI Audio Out”
setting is set to “AMP”.
25
–
Troubleshooting
24
Page
13
–
Information
•The pre-out assignment for the •Set the pre-out assignment to
surround back speakers is not the surround back speakers.
set.
•“S.Back” setting is set to •Set to something other than
“None”.
“None”.
•The “Parameter” – “Surround •Please set “Parameter” –
Parameter” – “SB CH Out” “Surround Parameter” – “SB
settings are “OFF”.
CH Out” to settings other than
“OFF”.
•Surround mode not set to a mode •Select a surround playback
for 6.1- or 7.1-channel playback.
mode.
•Subwoofer’s power not turned •Turn on the subwoofer’s power.
on.
•The “Subwoofer” setting at •Set to “Yes”.
“Speaker Config.” is set to “No”.
•The subwoofer is not properly •Check the connections.
connected.
•The subwoofer’s volume is •Adjust the subwoofer’s volume
turned off.
to an appropriate level.
•Blu-ray Disc player / DVD player’s •Set the Blu-ray Disc player / DVD
audio output setting is not set to player. For details, refer to the
bitstream.
Blu-ray Disc player / DVD player’s
operating instructions.
•Blu-ray Disc player / DVD player is •Use a DTS-compatible player.
not compatible with DTS sound
playback.
•The AVR-590’s “Decode Mode” •Set to the “Auto” or “DTS”
setting is set to “PCM”.
mode.
•The “Manual Setup” – “HDMI •Set to “AMP”.
Setup” – “HDMI Audio Out”
setting is set to “TV”.
Cause
Countermeasure
•HDMI is not connected.
•Connect the HDMI.
•Blu-ray Disc player’s audio output •Set the Blu-ray Disc player. For
setting is not set to bitstream.
details, refer to the Blu-ray Disc
player’s operating instructions.
•Blu-ray Disc player is not •Use a DTS-compatible player.
compatible with DTS sound
playback.
Remote Control
HDMI audio
signals are not
output from
speakers.
No sound is
output from
the monitor
connected
with HDMI
connections.
Symptom
Dolby TrueHD,
DTS-HD, Dolby
Digital Plus audio
is not output.
Playback
DTS sound is not
output.
Page
37
Settings
No sound is
produced from
subwoofer.
Cause
Countermeasure
•You are playing a monaural source •The mode is set to something
(TV, etc.) in the “STANDARD” other than “STANDARD” (Dolby/
(Dolby/DTS Surround) mode.
DTS Surround).
•The surround mode is set to •Set to a surround playback
“STEREO”, or “DIRECT”.
mode.
Connections
Symptom
No sound is
produced from
center speaker.
No sound
is produced
from surround
speakers.
No sound is
produced from
surround back
speaker.
Getting Started
GAudioH
28
28
29
29
56
ENGLISH
Getting Started
GHDMIH
Connections
Settings
Playback
Remote Control
Symptom
HDMI audio
signals are not
output from
speakers.
Cause
Countermeasure
•The “Manual Setup” – “HDMI •Set to “Amp”
Setup” – “HDMI Audio Out”
setting is set to “TV”
No picture
appears
with HDMI
connections.
•The connections to the HDMI
connectors are faulty.
•HDMI input setting is improper.
•The monitor is not compatible
with
copyright
protection
(HDCP).
•The HDMI format of the player
and monitor do not match.
•The “Manual Setup” – “HDMI
Setup” – “HDMI Audio Out”
setting is set to “Amp”.
Page
27
Perform this procedure if the display is abnormal or if operations cannot be performed.
When the microprocessor is reset, all the settings are reset to their default values.
Information
Troubleshooting
No sound is
output from
the monitor
connected
with HDMI
connections.
When performing •HDMI’s
CEC
the following
operating.
operations on a
connected device,
AVR-590 has the
same operations.
⋅Power ON/OFF
⋅Switching audio
output devices
⋅Adjust volume
⋅Switch input
source
•Check the connections.
13
•Check the HDMI input setting.
•Connect a monitor that is
compatible
with
copyright
protection (HDCP).
•Match the HDMI format of the
player and monitor.
•Set to “TV”.
31
12
12
27
Specifications
Symptom
57
Cause
1 Turn off the power using on the main unit.
simultaneously pressing
and
2 Press on thewhile
main unit.
the display starts flashing at intervals of about 1
3 Once
second, release the two buttons.
If in step 3 the display does not flash at intervals of about 1 second, start over from step 1.
function
is •Set “Manual Setup” – “HDMI
Setup” -– “HDMI Control” to
“OFF”.
When you only want to operate
the power on/off each device, set
“Power Off Control” to “OFF”.
27
GiPodH
iPod cannot be
played.
Restoring all the settings to as they were at the
time of purchase
(Resetting the Microprocessor)
Countermeasure
•The input source assigned to •Switch to the input source
“iPod Dock” is not selected.
assigned at “iPod Dock”.
•Cable is not properly connected. •Reconnect.
•Control dock for iPod’s AC •Plug the control dock for iPod’s
adapter is not connected to AC adapter into a power outlet.
power outlet.
Page
31
14
–
ENGLISH
Getting Started
Specifications
nAudio section
Connections
• Power amplifier
Rated output:
Front :
75 W+75 W
(8 Ω/ohms, 20 Hz ~ 20 kHz with 0.08 % T.H.D.)
110 W+110 W (6 Ω/ohms, 1 kHz with 0.7 % T.H.D.)
Center:
75 W
(8 Ω/ohms, 20 Hz ~ 20 kHz with 0.08 % T.H.D.)
110 W
(6 Ω/ohms, 1 kHz with 0.7 % T.H.D.)
Surround:
75 W+75 W
(8 Ω/ohms, 20 Hz ~ 20 kHz with 0.08 % T.H.D.)
110 W+110 W (6 Ω/ohms, 1 kHz with 0.7 % T.H.D.)
Output connectors:
Front, Center, Surround :
6~16 Ω/ohms
• Analog
Input sensitivity / Input impedance: 200 mV / 47 kΩ/kohms
Frequency response:
10 Hz ~ 100 kHz — +1, –3 dB (DIRECT mode)
S/N:
98 dB (IHF-A weighted, DIRECT mode)
Settings
Playback
Remote Control
nVideo section
nTuner section
Y (brightness) signal — 1 Vp-p, 75 Ω/ohms
PB / CB signal — 0.7 Vp-p, 75 Ω/ohms
PR / CR signal — 0.7 Vp-p, 75 Ω/ohms
5 Hz ~ 60 MHz — +0, –3 dB
[AM]
520 kHz ~ 1710 kHz
18 µV
Specifications
[FM]
(note: µV at 75 Ω/ohms, 0 dBf = 1 x 10-15 W)
87.5 MHz ~ 107.9 MHz
1.2 µV (12.8 dBf)
MONO 2.8 µV (20.2 dBf)
STEREO 48.7 µV (45.0 dBf)
MONO 70 dB
STEREO 67 dB
MONO 0.7 %
STEREO 1.0 %
Troubleshooting
Receiving Range:
Usable Sensitivity:
50 dB Quieting Sensitivity:
S/N (IHF-A):
Total harmonic Distortion (at 1 kHz):
1 Vp-p, 75 Ω/ohms
5 Hz ~ 10 MHz — +1, –3 dB
Information
• Standard video connectors
Input / output level and impedance:
Frequency response:
• Color component video connector
Input / output level and impedance:
Frequency response:
nGeneral
Power supply:
Power consumption:
Maximum external dimensions:
Weight:
AC 120 V, 60 Hz
4.3 A
0.3 W (Standby)
434 (W) x 171 (H) x 377 (D) mm (17-3/32” x 6-47/64” x 14-27/32”)
9.3 kg (20 lbs 8 oz)
nRemote control unit (RC-1120)
Batteries:
Maximum external dimensions:
Weight:
R03/AAA Type (two batteries)
50 (W) x 211 (H) x 22 (D) mm (1-31/32” x 8-5/16” x 55/64”)
110 g (Approx 3.9 oz) (including batteries)
z For purposes of improvement, specifications and design are subject to change without notice.
58
List of preset codes / Liste de codes préréglés
DEVICE SELECT : TV
Television
A
A.R. Systems
Accent
Accuscan
Action
Acura
Addison
ADL
Admiral
Advent
Adventura
Adventuri
Agna
Aiko
Aim
Aiwa
Akai
Akashi
Akiba
Akito
Akura
Alaron
Alba
Albatron
Alfide
Alleron
Allstar
All-Tel
A-Mark
Ambassador
America Action
American High
Ampro
Amstrad
Amtron
Anam
Anam National
Anglo
Anhua
Anitech
Ansonic
AOC
Apex Digital
Archer
284
276, 284
224
188, 268
276
238
349
045, 233, 213, 218, 224, 233,
239, 244, 252
219, 242, 280, 287, 288, 293
032
235
182
238, 276, 284, 316
241, 284
172, 216, 264, 380, 400, 413,
414
016, 186, 188, 190, 193, 209,
235, 237, 246, 253, 254, 274,
276, 284, 300, 316
276
284
284
214, 276, 284, 356
319
209, 276, 284
186, 248
246
062, 188, 319
284
249
218, 224, 276
182, 320
239
235, 237
261
214, 235, 276, 272, 284, 320
235, 239
006, 036, 177, 186, 239, 276,
284, 299
036, 177, 239, 268, 284
276
213
276, 284
276, 284
048, 133, 184, 188, 193, 233,
235, 237, 238, 239, 276, 299,
319
170, 192, 194, 259
276
PRESET CODE
B
Asora
Audiovox
Awa
Axion
Axxent
Baihe
Baile
Baird
Basic Line
Bauer
Baur
Baysonic
Beaumark
Beijing
Beko
Belcor
Bell & Howell
BenQ
Beon
Bestar
Blaupunk
Blue Sky
Boots
Boxlight
BPL
Bradford
Brinkmann
Brionvega
Brockwood
Broksonic
C
Bush
Caihong
Cailing
Candle
Capehart
Capetronic
Carena
Carnivale
Carrefour
Carver
Cascade
Casio
Cathay
CCE
Celebrity
Celera
Celestial
Centurion
Changcheng
Changfei
276
276
184, 272
301, 302
276
276
185, 276
284
276, 284
023
284
239, 240, 252
188, 193, 244
185, 254, 276, 280, 283
284
188, 235
045, 191, 218, 233, 244
198, 205
284
284
319
221, 284, 291
276
346
284
239
284
284
188, 193, 235
172, 209, 239, 240, 252, 320,
361
185, 276, 284
276, 280
170
030, 032, 050, 188, 193, 235,
319
188, 193, 238, 244
188
284
188
284
218, 319
276, 284
284
284
284
193, 235
259
194
284
185, 213, 276, 280
276, 280
Changfeng
Changhai
D
280
276, 280
192, 194, 201, 259, 276, 280,
Changhong
287
Chengdu
276, 280
Ching Tai
238, 276
Chun Yun
186, 235, 238, 239, 248, 276
Chunfeng
276
Chung Hsin
173, 239
Chunsun
276, 280
Cimline
276
Cinema
246
Cineral
184, 238
Circuit City
193
Citek
224
023, 030, 032, 034, 050, 123,
184, 188, 193, 209, 214, 218,
Citizen
235, 237, 238, 239, 252, 316,
319
City
276
Clarion
239
Clarivox
284
Classic
188, 238
Clatronic
276, 284
188, 193, 218, 224, 235, 237,
Colortyme
244, 319
Commercial Solutio 229
Commercial
224
Solutions
Concerto
193, 235
Concorde
276
Condor
276, 284
Conia
356
Conic
193
Conrowa
190, 192, 201, 276
Contec
013, 023, 041, 239, 276, 284
Cony
023, 041, 239
Cosmel
276, 284
Craig
214, 239
Crosley
188, 214, 218, 235, 239
023, 173, 233, 239, 246, 276,
Crown
284
Crown Mustang
246
CTX
205
023, 034, 044, 053,184, 188,
190, 191, 193, 210, 213, 218,
Curtis Mathes
224, 226, 228, 233, 235, 237,
239, 253, 282, 284, 316, 319
CXC
239
Daenyx
239, 246
023, 048, 107, 184, 185, 186,
187, 188, 191, 193, 205, 215,
Daewoo
237, 238, 239, 246, 249, 258,
276, 284, 299, 319, 388, 389,
395
Dansai
276, 284, 316
Dawa
276, 284
E
Daytek
Daytron
Dayu
Decca
Dell
Denon
Denstar
Denver
Desmet
Dewo
Diamant
Diamond
Digatron
Digiline
Digital Life
Digitor
Dimensia
Dixi
DL
Dongda
Donghai
Dream Vision
Drean
DTS
Dual
Dumont
Durabrand
Dux
D-Vision
Dwin
Dynatron
Eaton
ECE
Elbe
Electroband
Electrograph
Electrohome
Elekta
Elektra
ELG
Elin
Elite
Elta
Emerald
Emerson
Envision
Epson
Erres
246
188, 193, 238, 239, 276, 284
185
284
220, 348
190, 322
299
284, 285
276, 284
299
284
241, 246, 276
284
284
340
284
044
027, 222, 276, 284
285, 340
276
276
359
284
276
284
193, 239, 244
171, 193, 214, 239, 251, 252
284
284
233, 297
284
237
284
284
193, 235
215
023, 036, 058, 182, 188, 191,
193, 235, 240, 252, 274
276
187, 244
284
276, 284
284
027, 276
193, 320
023, 060, 062, 123, 124, 148,
172, 173, 182, 184, 191, 193,
214, 239, 224, 244, 251, 284,
239, 240, 252, 258, 319, 320,
362
188, 319, 329
331, 333
284
F
ESA
ESC
Ether
Etron
Euroman
Europa
Europhon
Evolution
Exquisit
Feilang
Feilu
Feiyue
Fenner
Ferguson
Fidelity
Finlux
Firstar
Firstline
Fisher
Flint
Formenti
Fortress
Fraba
Friac
Frontech
Fujimaro
Fujitsu
Fujitsu General
Fujitsu Siemens
Funai
G
Furi
Futuretech
Galaxi
Galaxis
Ganxin
Gateway
GBC
GE
GEC
Geloso
Gemini
General Electric
General Technic
Genesis
Genexxa
Gericom
Giant
Gibralter
Go Video
214, 254, 362
284
188, 276
027, 276
284
284
284
205
284
276
276, 280
276, 280
276
173, 209, 284
214, 284
284
240, 276
276, 284
021, 191, 218, 224, 235
284
023, 284
233
284
276, 284
276
249, 356
062, 178, 179, 180, 214, 276
178, 276
179
062, 214, 216, 235, 239, 396,
397
190, 280
066, 239
284
284
280
205, 215
276
034, 036, 044, 058, 066, 088,
184, 188, 193, 222, 213, 224,
226, 228, 229, 231, 233, 234,
235, 237, 238, 239, 316
284
276
224
224
276
276, 284
276, 284
249, 349
276
188, 235, 244
237, 344
Go Vision
Goldstar
Goodmans
H
Gradiente
Granada
Grandin
Grundig
Grundy
Haaz
Haier
Haihong
Haiyan
Hallmark
Hankook
Hanseatic
Hantarex
Hantor
Harley Davidson
Harman/Kardon
Harsper
Harvard
Harwood
Hauppauge
Havermy
HCM
Heathkit
Helios
Hello Kitty
Hema
Highline
Himitsu
Hinari
Hisense
Hitachi
Hitachi Fujian
Hitachi Pay TV
Hitsu
Hoeher
Hongmei
Hongyan
Hornyphon
Hua Tun
Huafa
Huanghaimei
Huanghe
Huanglong
Huangshan
Huanyu
301
023, 048, 133, 188, 191, 193,
213, 222, 224, 240, 275, 276,
284, 290
185, 235, 272, 276, 284, 285,
316
173, 284, 319
283, 284
249, 276, 284
178, 209, 241, 246, 285
062, 139
241
171, 267, 287, 285
276
280
193, 239, 240
188, 193, 239, 299
185, 276, 284
249, 276, 284
284
188, 193, 216, 235, 237, 239
218
249
239
276, 284
284
233
276, 284
244
249
184
276
184
239, 299
276, 284
170, 190, 192, 201, 276, 291
023, 041, 070, 124, 182, 188,
190, 192, 193, 199, 201, 202,
208, 213, 216, 218, 224, 235,
238, 244, 274, 284, 316, 376,
384, 385, 386, 394, 408, 409,
410, 412
182
151
276
249
233, 276, 280
280
284
276
190, 276
276
276, 280
276
276, 280
280
I
J
Huari
Hugoson
Huodateji
Hyper
Hypson
Hyundai
Iberia
ICE
Iiyama
Ima
Imperial
Imperial Crown
Indiana
Infinity
Ingersol
Inno Hit
Innova
Innowert
Insignia
Inteq
Interbuy
Interfunk
Internal
Intervision
Irradio
IRT
Isukai
ITS
ITT Nokia
ITV
Janeil
JBL
JC Penny
JCB
Jean
JEC
Jensen
Jiahua
JiaLiCai
JIL
Jinfeng
Jinque
Jinta
Jinxing
Juhua
Jutan
JVC
K
Kaige
Kaisui
Kamp
Kangli
190
309, 349
213
276
284
195, 249
284
284
309, 349
193, 239, 240
284
185, 276
284
017, 218, 222
276
276
284
249
214
190, 244
276, 284
184
184
276, 284
276, 284
184, 187, 299
184
184
239
284
032
018, 218, 222
034, 041, 044, 048, 050, 058,
066, 088, 094, 192, 193, 237,
275
193, 235
192, 213, 238, 240, 276
316
242, 280, 288, 293
213
276
188
213, 283
276, 280
276
190, 192, 218, 276, 280, 284
280
188
023, 041, 072, 073, 173, 174,
175, 176, 178, 188, 218, 233,
252, 268
276, 280
276, 284
239, 244
185, 276, 280
Kangyi
Kawasho
KDS
KEC
Ken Brown
Kendo
Kenia
Kenwood
Khind
Kioto
KLH
KLL
Kloss
Kloss Novabeam
Kneissel
Kolin
Kolster
Kongque
Konichi
Konig
Konka
L
Korpel
Kosmos
Kost
Koyoda
KTV
Kuaile
Kulun
Kunlun
L&S Electronic
Lark
Leader
Lecson
Legend
Lenco
Lenoir
Leyco
LG
Liesenk & Tter
Liesenkotter
Lifetec
Lihua
Lloyd's
Local Chennai TV
Local India TV
Loewe
Logik
Longjiang
Luma
Lumatron
Lux May
276
018, 188, 193
356
237, 239
240, 252
284
188
188, 193, 239, 240, 319
241
218, 241, 284
192
284
005, 032, 188
005, 032, 101
284
173, 182, 239, 355
284
276, 280
276
284
239, 263, 265, 266, 280, 284,
285, 286, 297, 299
284
284
278
276
074, 123, 188, 239, 252
276
276
185, 213, 280, 283
249
191
276
284
276
284, 285
276
284
188, 193, 186, 196, 218, 237,
276, 284, 290, 348, 351, 360,
387, 394
284
284
178, 276, 284
280
188, 216, 239, 240, 276
276
276
222, 284
045, 237, 239, 240, 349, 272,
276
280
276
284
276, 284
Luxman
LXI
M
M&S
M Electronic
Madison
MAG
Magnadyne
Magnasonic
Magnavox
Magnum
Majestic
Manesth
Manhattan
Marantz
Mark
Mastro
Masuda
Matsui
Matsushita
Matsuviama
Maxent
MCE
Mediator
Medion
Megapower
Megatron
Meile
Memorex
Memphis
Mercury
Mermaid
Metz
MGA
MGN Technology
Micro Genius
Micromaxx
Midland
Minato
Minoka
Minutz
Mitsubishi
Monaco
Monivision
Montgomery Ward
193
017, 034, 044, 075, 103, 188,
191, 192, 193, 210, 213, 214,
218, 222, 224, 233, 235, 237,
244, 284, 316
218
185, 276, 284
284
356
218
235, 188, 218, 238, 233, 192
005, 017, 030, 050, 079, 085,
089, 101, 108, 110, 177, 188,
191, 193, 213, 214, 215, 216,
218, 221, 222, 224, 237, 238,
235, 239, 241, 272, 284, 316,
319, 328, 362
284
244
316, 284
284
017, 193, 188, 284, 218, 324,
289, 290, 222
276, 284
173, 241
276, 284
022, 276, 272, 316, 284, 320
213, 177, 268
285
205, 215
276
284
284
186
276, 224, 190, 274, 193
180
027, 045, 276, 188, 316, 284,
237, 182, 191, 193, 239, 177,
252, 172
276
276, 284, 237
284
160, 161, 162, 284, 285
182, 193, 048, 240, 058, 021,
018, 188
193
182
284
034, 244, 224, 213
284
284
066
016, 021, 048, 058, 081, 105,
177, 182, 188, 191, 193, 233,
234, 239, 240, 272, 277, 280,
281, 284, 369, 385, 386, 394
276
186, 248
011, 066, 101, 144, 235
Morgan's
Motorola
MTC
Mudan
Multitec
Multitech
Mx Onda
N
NAD
Naiko
Nakimura
Nanbao
Nansheng
NAT
National
National Quenties
NEC
O
Neckermann
NEI
Neovia
Netsat
NetTV
Neufunk
New Tech
Newave
Nikkai
Nikko
Nikkodo
Nishi
Noblex
Nokia
Norcent
Nordmende
Normerel
Novatronic
NTC
Nyon
Okano
Olevia
Omni
Onida
Onwa
Opera
Optimus
Optoma
Optonica
Orbit
Orion
Orline
284
036, 182, 213, 218, 233
034, 048, 188, 193, 237, 238,
239, 272
276, 213, 283, 280
284
276, 284, 239
356
075, 192, 193, 201, 210, 211,
212, 284
284
284
276
280
283
036, 213, 239, 283
283
319, 036, 048, 173, 185, 188,
191, 192, 193, 213, 224, 240,
276, 272, 280, 319, 321, 323,
324, 342, 359
284
284
249
284
215
276, 284
276, 284
276, 238, 233, 193
276, 316, 284
188, 238, 193
188, 238, 193
188
284, 191
239
170, 247
284
284
284
238
235
276, 284
347, 350, 355, 358
170, 340
173, 175
239
284
211, 188, 233, 182, 191, 210,
193, 239, 177, 268
345
011, 233
284
214, 272, 244, 284, 320, 193,
239, 240, 252, 251, 172
284
PRESET CODE
P
Osaki
Osio
Osume
Otic
Otto Versand
Pace
Pacific
Packard Bell
Palladium
Palsonic
Panama
Panasonic
Panavision
Panda
Pausa
Paxonic
PCE
Penney
Perdio
Perfekt
Petters
Philco
Philips
Phoenix
Phonola
Pilot
Pioneer
Plantron
Playsonic
Polaroid
Poppy
Portland
Powerpoint
Precision
Premier
Price Club
Prima
Princeton
Prism
Profex
Profi
Profitronic
Proline
Proscan
284
284
284
356
284, 233, 283
238
284, 209
238, 291
284
284, 216
276, 284
009, 017, 036, 177, 181, 188,
192, 213, 218, 222, 235, 240,
270, 271, 283, 284, 268, 180,
269, 311, 316, 376, 384, 385
284
276, 213, 283, 241, 280
276
188, 237
237, 192
235, 188, 316, 284, 224, 213,
237, 192, 193, 177, 228
284
284
357
005, 023, 030, 036, 079, 050,
085, 089, 101, 172, 184, 187,
188, 190, 284, 218, 238, 239,
252, 193, 299
005, 017, 023, 030, 036, 050,
087, 088, 089, 101, 188, 193,
205, 213, 214, 217, 218, 221,
222, 223, 235, 238, 244, 276,
284, 290
284
284
272, 288, 213, 237, 193, 241
124, 142, 370, 415, 416, 272,
284, 319, 218, 211, 212, 310
276, 284
284
258, 249, 278, 291, 279, 353,
354, 292, 356, 357
276
238, 184
284
320, 239, 240
276
237
276, 242, 287, 288, 280, 293
186, 325
213, 177
276
276
284
284
034, 044, 224, 282, 228, 229,
231
PRESET CODE
Prosco
Prosonic
Protec
Protech
Proton
Q
Proview
ProVision
Pulsar
Pye
Pymi
Qingdao
Quadral
Quartz
Quasar
R
Quelle
Rabbit
Radio Shack
Radiola
Radiomarelli
RadioShack
Radiotone
RCA
Realistic
S
Recor
Rectiligne
Redstar
Reflex
Relisys
Remotec
Revox
RFT
R-Line
Roadstar
Rowa
Runco
Ruyi
Saba
Saige
Saisho
Saivod
Sampo
Samsung
Sanky
Sansei
192
284
276, 284
276, 284
185, 023, 092, 276, 188, 193,
282
356
284
149, 244, 238, 193
284
276
213, 283, 280
213
182, 193
036, 213, 074, 276, 316, 177,
268, 249
272, 284
224
011, 044
284
284
188, 284, 224, 182, 191, 193,
239, 216
276, 284
034, 044, 130, 151, 152, 185,
188, 189, 193, 211, 222, 213,
218, 224, 225, 226, 227, 228,
229, 230, 231, 232, 233, 235,
237, 238, 234, 302, 312
011, 181, 224, 182, 191, 193,
239
284
284
284
284
249
284, 233, 190, 214, 177
284
284
284
276, 284
276, 284, 285, 176, 280
244, 288, 237, 321, 323
280
177
276, 280
027, 276, 272, 320
284
276, 188, 224, 238, 233, 191,
214, 193, 268, 186, 215, 205
034, 094, 053, 188, 189, 191,
192, 193, 218, 222, 224, 233,
237, 238, 240, 243, 244, 253,
254, 257, 260, 276, 280, 283,
284, 285, 300, 308, 316, 318,
382, 401
188, 237
238, 184
Sansui
Santon
Sanyo
Sanyong
Sanyuan
Saville
SBR
Sceptre
Schneider
Scotch
Scott
Sears
SEG
SEI
Sei-Sinudyne
Semivox
Semp
Sencora
Sentra
Serie Dorada
Serino
Shancha
Shanghai
Shaofeng
Sharp
Shen Ying
Shencai
Sheng Chia
Shenyang
Sherwood
Shintoshi
Shivaki
Show
Siam
Siemens
Siera
Signature
Signet
Silva
Silva Schneider
Silvano
Simpson
Singer
Sinudyne
SKY
251, 188, 284, 237, 252, 241,
216, 172, 209
276
013, 021, 081, 096, 190, 191,
192, 214, 215, 218, 224, 235,
239, 245, 252, 276, 272, 284,
290, 319, 324, 327, 346, 384,
392, 393, 404
284
276, 233, 280
237
222, 284
349
222, 284, 216
193
062, 188, 320, 193, 239, 240
021, 023, 034, 041, 062, 073,
075, 173, 188, 191, 192, 193,
210, 213, 218, 214, 216, 224,
233, 235, 237, 240, 244, 284,
316, 327
276, 284
284, 320
284
239, 240, 252
192, 203
276
316
188, 192, 193, 239
233
280
276, 283, 280
190, 280
011, 013, 026, 099, 104, 173,
188, 218, 233, 234, 239, 268,
372, 373, 276, 294, 295, 296,
297, 298, 398, 402, 403
276, 238
276, 190
276, 233, 240
276, 280
276
284
284, 193
276
284
013, 284, 190
284
045, 144, 188, 224, 233
278
284
284
285
050, 272, 188, 193
276, 284, 273, 238
284, 320
284
Skygiant
Sky-North
Skyworth
Sliding
Soemtron
Solar Drape
Solavox
Sole
Songba
Soniko
Sonneclair
Sonoko
Sontec
Sony
Soundesign
Soundwave
Sova
Sowa
Spectra
Spectravision
Spectricon
Spectroniq
Squareview
SR2000
Ssangyong
SSS
Staksonic
Standard
Standard
Component
Starlite
Strato
Studio Experience
Sunkai
Sunstar
Sunwood
Superscan
Supersonic
SuperTech
Supra
Supre-Macy
Supreme
Sutron
SV2000
SVA
Sylvania
Symphonic
Synco
239
284
276, 284, 170, 280
249
249
235
284
329
276
284
284
276, 284
276, 284
173, 182, 191, 193, 216, 235,
236, 244, 263, 268, 272, 284,
[374]*, 375, 399, 405, 406,
407, 368, 366
030, 050, 062, 193, 239
284
364
213, 237, 238, 192, 193, 283
276
192, 193
276
356
214
191
214
276
239
276
276
276, 284, 239, 240
276, 284
248
249
276, 284
284
233, 337, 362
276
276, 284
276, 193
032
235, 193
276
218
285, 170, 267, 249, 338, 339,
340
005, 017, 023, 030, 079, 085,
089, 101, 188, 191, 193, 213,
214, 216, 218, 224, 235, 238,
284, 291, 362
148, 235, 214, 193, 239, 216,
362
235, 237, 238, 233, 193, 184
T
Syntax
Sysline
Tacico
Tai Yi
Taishan
Talent
Tandy
Tashiko
Tatung
TCL
Teac
Tec
Tech Line
Technics
Technovox
Techview
Techwood
Teco
Tedelex
Teiron
Teknika
Telecolor
Telecor
Telefunken
Telefusion
Telegazi
Telemeister
Telesonic
Telestar
Teletech
Teleview
Tempest
Tennessee
Tensai
Tenson
Tera
Tevion
Texet
ThemeScene
Thomas
Thomson
Thorn
Tiane
TMK
TNCi
Tobo
Tocom
Tokai
Tokyo
Tongtel
347, 350, 355
284
276, 238, 193
276
276, 280
193
233
238, 319, 268
036, 124, 235, 276, 272, 284,
213, 218, 237, 191, 192, 201,
221, 205
241
276, 284, 191, 319, 214, 193,
296, 241, 215, 216
276, 284
284
213, 218, 283, 177, 268
188
335
213, 237, 177
276, 213, 238, 233, 193
276
276
030, 032, 034, 041, 144, 156,
218, 237, 238, 182, 193, 239,
252
244
284
284, 285, 253
284
284
284
284
276, 284
276, 284
284
276
284
276, 284
276
185, 188, 238, 282
284, 194, 356
276
345
224, 193, 216
165, 166, 284, 224, 229
316, 284
233, 280
320, 193, 239, 240
244
276, 170
192
276, 284
316
285
Tophouse
Toshiba
U
V
W
Totevision
Toyoda
Toyomenka
Trans Continens
TRANS-continents
Transonic
Trio
Triumph
Truetone
Tuntex
TVS
Uher
Ultra
Ultravox
Unic Line
United
Universal
Universum
Univox
V
V2max
V7 Videoseven
Vector Research
Vestel
Vexa
Victor
Video Concepts
Videocon
Videomac
VideoSystem
Vidikron
Vidtech
Viewsonic
Viking
Vision
Vizio
Vortec
Voxson
Waltham
Wards
Warumaia
Watson
Waycon
Wega
Wegavox
239, 246
034, 075, 094, 041, 182, 190,
191, 192, 199, 201, 202, 203,
204, 207, 209, 210, 237, 233,
268, 276, 272, 316, 330, 334,
351, 359, 365, 371, 390, 391
213
276
193
284
249
276, 284, 285
356
284, 320
213, 177
276, 188, 238
252
284
238
284
284
284, 285
066, 088, 284, 224
276, 272, 284, 319, 320
284
337, 343, 215, 205
249
349, 215
188
284
276, 284
173, 177, 268
016
284
276
284
218
193
336, 337, 343, 215
032, 237
284
337, 343, 215, 205, 360
284
284, 193
284
005, 011, 045, 030, 085, 088,
089, 101, 102, 148, 188, 191,
192, 193, 201, 210, 212, 213,
218, 224, 226, 228, 233, 235,
237, 239, 240, 244, 274, 284,
316
185
276, 284
192
284
276
X
Y
Z
Weipai
Welton
Westinghouse
Wharfedale
White
Westinghouse
World
World-of-Vision
Xenius
Xiahua
Xianghai
Xiangyu
Xihu
Xingfu
Xoro
XR-1000
Xrypton
Yamaha
Yamishi
Yapshe
Yingge
Yokan
Yoko
Yonggu
Yorx
Youlanasi
Yousida
Yuhang
Zenith
ZhuHai
Zonda
276
193
235, 184, 343, 250, 309, 367
284
G
284, 240, 184, 252, 258, 250
239, 240, 184, 252
249, 309, 349
185
176, 280
276
276
280
276
049
191, 214, 239
284
188, 268, 326, 331, 332
284
177
276
284
276, 284
276
188
208
276
276
140, 144, 149, 235, 244, 188,
284, 224, 238, 233, 190, 214,
193, 252, 254, 199, 351, 216,
172
276
276
DEVICE SELECT : DVD
H
I
J
K
L
M
N
O
P
R
DVD Player
A
B
C
D
E
F
Aiwa
Alba
Apex Digital
Blaupunkt
Bush
Clatronic
Creative
Daewoo
Denon
Dual
Emerson
Entivo
Finlux
Firstline
Funai
002, 009
017, 040
002, 040
040
040
015
001, 017
023, 114
[111]*, 112, 113, 114
015
015, 046
001, 017
046
023
015
S
Gateway
GE
General Electric
Go Video
Goldstar
Gradiente
Grundig
HITACHI
Integra
Irradio
JVC
Kenwood
KLH
Kloss
Konka
LG
Luxman
Magnasonic
Magnavox
042, 043, 044, 045
038, 040
038, 040
010, 023, 040
023, 046
114
017
010
001
023
001, 006, 011, 017
114
040
002
012, 013
023, 046
010
015
001, 015, 017
Marantz
001, 015, 017
Metz
003, 008
C
D
E
F
J
Micromedia
001, 017
K
Kenwood
Mitsubishi
004, 033
M
Magnavox
NEC
023
Marantz
Optimus
003, 008
MCS
Panasonic
001, 008, 114
Panda
040
Philco
015
Philips
001, 005, 015, 016, 017
Pioneer
003, 008, 114
Pye
017, 023
RadioShack
008
RCA
008, 038, 040
Realistic
008
Rotel
006, 011
Rowa
040
Samsung
010, 114
Sanyo
015, 018, 037
Schneider
017, 023
Sharp
015
Sherwood
040
Sonic Blue
010, 023
SONY
002, 010, 019
SVA
040
Sylvania
015
T
U
Y
Z
Symphonic
015
Teac
008, 015, 040
Technics
114
Thomson
038
Toshiba
001, 010, 017, 021
United
015
Universum
023, 046
Yamaha
Zenith
016, 017, 114
001, 023, 046
CD Player
A
B
O
Aiwa
Burmester
Burmster
Carvery
Denon
Emerson
Fisher
JVC
Onkyo
Optimus
P
Philips
Pioneer
S
Sears
Sony
T
Teac
Technics
W
Y
Z
Wards
Yamaha
Zenith
150, 201, 235, 243
151
202
150, 202, 203, 235
167, 189, 190, 191, 192, 222,
234, 244
204, 205, 206, 207
155, 203, 208, 209, 210
158, 173, 218, 219
155, 162, 163, 164, 165, 166,
167, 168, 211, 212, 213, 214,
217
150, 156, 206, 215, 235
150, 152, 153, 156, 163, 170,
216, 228, 235
163, 216, 224
159, 177, 178, 179, 180, 181,
182, 183, 184, 185, 225, 227
151, 155, 158, 165, 172, 217,
220, 221, 223, 226
167, 214, 232, 233, 235
158, 159, 160, 161, 206,
226, 230
206
154, 155, 174, 175, 176,
223, 231
152, 153, 154, 202, 209, 228
163, 171, 216, 229, 236
150, 155, 158, 172, 186,
235, 237
154, 158, 164, 177, 187, 188,
238, 239, 240, 241
242
O
P
R
S
Sharp
T
Y
D
H
I
J
L
M
Denon
Hitachi
Integra
JVC
LG
Marantz
Mitsubishi
038, 039, [111]*
034, 035, 036
012
013, 014, 016, 017, 018, 019
010
025, 026
023, 024
Sony
Toshiba
Yamaha
011, 012
001, 002, 003, 040, 041
004
005, 037
011
006
031, 032, 033, 027, 028, 029,
030
007, 008, 009, 015
011
020, 021, 022
DEVICE SELECT : DVR
Digital Video Recorder
A
F
H
J
M
P
S
T
V
Y
ALCO
ATLM
Funai
Hitachi
JVC
Mitsubishi
Panasonic
Pioneer
SANYO
Sharp
SONY
TOSHIBA
Victor
YAMAHA
011
010
035
031, 032, 033, 034, 036, 037
[001]*, 002, 003, 004
038, 039
036, 037
027, 028, 029, 030
009
040, 041
012, 023, 024, 025, 026
006, 007, 008, 042, 043
020, 021, 022, 040, 041
005
DEVICE SELECT : VCR
Video Cassette Recorder
A
DEVICE SELECT : HDP
Blu-Ray Disc Player
Onkyo
Panasonic
Philips
Pioneer
RCA
Samsung
B
C
Admiral
Aiko
081
095
Aiwa
009, 026, 027, 070, 072, 082,
083, 084
Alba
Amstrad
ASA
Asha
Audio Dynamic
Audiovox
Beaumark
Broksonic
Calix
Candle
Canon
Capehart
055
009
042
087
005, 085
088
087
086, 093
088
006, 087, 088, 089, 090
049, 057
025, 055, 056, 071
PRESET CODE
F
G
H
J
K
L
M
PRESET CODE
NEC
O
P
Nikko
Noblex
Optimus
Optonica
Panasonic
Pentax
Perdio
Philco
Philips
Pilot
Pioneer
Q
R
Portland
Proscan
Pulsar
Quartz
Radio Shack
Radix
Randex
RCA
Realistic
S
Ricoh
Salora
Samsung
Sanky
Sansui
Sanyo
SBR
Scott
Sears
Sentra
Sharp
Shogun
Sony
STS
Sylvania
T
Symphonic
Tandy
Tashiko
Tatung
Teac
Technics
TMK
009, 087, 094
007, 009, 011, 087, 090, 094
038
004, 005, 006, 018, 026, 029,
045, 061, 062, 085
088
087
081, 088
021
024, 049, 064, 066, 067, 068,
069, 107
009, 013, 023, 058, 090
009
015, 016, 049
015, 021, 042, 049, 105
088
005, 013, 029, 036, 037, 038,
045, 085
025, 055, 090
080, 063
060
033, 034, 049
001, 002, 021, 081, 087, 088,
091, 094, 097, 098, 115
088
088
007, 013, 019, 023, 058, 063,
064, 065, 073, 080, 082, 087
009, 021, 031, 033, 049, 053,
081, 087, 088, 091, 094, 097
,098
055
033, 041
007, 011, 051, 059, 070, 083,
087, 089, 113
081
005, 026, 029, 045, 061,
085, 114
032, 033, 053, 087, 091,
115, 116
042
017, 020, 086, 089, 093, 117
013, 023, 028, 031, 033, 053,
054, 088, 091, 098, 099, 115
055
001, 002, 021, 097
087
075, 076, 077, 078, 079,
121, 122
023
009, 015, 016, 017, 041,
049, 094
009, 094
009
009, 088
004, 026, 030
004, 009, 026, 094
024, 049
087, 092
Toshiba
U
V
W
X
Y
Z
Totevision
Unirech
Vecrtor Research
Victor
Video Concepts
Videosonic
Wards
XR-1000
Yamaha
Zenith
013, 017, 020, 041, 059, 089,
098, 099, 117
007, 087, 088
087
005, 062, 085, 089, 090
005, 045, 046, 085
005, 027, 085, 089, 090
007, 087
013, 021, 023, 087, 088, 089,
091, 094, 097, 118, 119, 120
094
004, 005, 006, 026, 062, 085
060, 078, 079
DEVICE SELECT : SAT/CBL
Satellite Receiver
A
C
Alphastar
Chaparrali
D
DirecTV
Dish Network
System
Dishnet
Drake
E
G
H
J
K
M
N
P
R
S
054
035, 036, 150, 154, 155
[095]*, 156, 157, 158, 162,
163, 166, 174, 176, 177, 179,
188, 189, 191, 193, 197, 198,
200, 202
164, 173, 194, 201
053
037, 038
062, 077, 095, 164, 168, 173,
Echostar Dish
187, 190, 194, 201
GE
048, 055, 056, 156, 157
General Instruments 039, 040, 041
070, 071, 072, 073, 152, 167,
Grundig
168, 171, 185
Hitachi
058, 059, 163, 166, 182, 183
063, 064, 065, 069, 163, 193,
Hughes Networkr
200
JVC
077, 164, 201
074, 075, 076, 083, 152, 153,
Kathrein
192, 196
Magnavox
060, 160, 162
070, 084, 085, 086, 161, 168,
Nokia
181
Panasonic
091, 155, 159, 167, 186
060, 150, 152, 153, 160, 162,
Philips
163, 164, 166, 060, 168, 172,
174, 178, 179, 193, 199, 200
Primestar
051
Proscan
048, 055, 056, 156, 157
048, 055, 056, 068, 151, 156,
RCA
157, 164, 169, 179, 185, 189,
193
Realistic
042
Sierra I
036
Sierra II
036
Sierra III
036
049, 067, 158, 167, 168, 195,
Sony
197, 198
STS1
043
STS3
STS4
T
Technisat
Toshiba
U
Uniden
045
046
077, 078, 079, 081, 082, 175,
180
047, 050, 163, 165, 166, 184,
200
061, 160, 162
C
E
G
H
J
M
O
P
ABC
Archer
Century
Citizen
Colour Voice
Comtronic
Eastern
Garrard
General Instrument
Goldstar
Hytex
Jasco
Jerrold
Magnavox
Motorola
Oak
Panasonic
Philips
Pioneer
R
S
RCA
Regency
Samsung
Scientific Atlanta
T
U
V
Z
Signal
SL Marx
Sony
Starcom
Stargate
Teleview
Tocom
Unika
United Artists
Universal
Viewstar
Zenith
DEVICE SELECT : DVD
DVD preset codes / Codes préréglés DVD
Cable TV
A
[ ]* :Preset codes set upon shipment from the
factory.
*[ ] :Les codes préréglés diffèrent en fonctiom
des livraison de l’usine.
006, 007, 008, 009, 118, 122
010, 011, 122
011, 118
011
012, 013
014
015
011
032, 108, 110, 111
100
006
011
007, 009, 032, 110, 111
018
110, 111, 113
006, 020, 101
001, 005, 100, 115, 116, 117,
118
011, 012, 013, 018, 021, 129,
130, 131, 133, 134
002, 003, 022, 100, 123, 126,
127, 128
029
015
014, 023, 100, 117, 119, 120
004, 024, 025, 117, 118, 121,
122, 123, 136
014
014
105, 132
009
014
014
007
011
006
010, 011
018, 104
027, 028, 117, 118, 125, 135
111
(default /défaut)
e Model No. / Modéle numéro
E
N
MTC
Multitech
NAD
DVD-900
DVD-700
DVD-1000
DVD-1400
DVD-1500
DVD-1710
DVD-1720
DVD-1730
DVD-1740
DVD-1910
DVD-1920
DVD-1930
DVD-1940
DVD-2200
DVD-2800
DVD-2800g
DVD-2900
DVD-2910
DVD-2930
DVD-3800
DVD-3910
DVD-3930
DVD-A11
DVD-A1XV
DVD-A1
112
DVD-800
DVD-1600
DVD-2000
DVD-2500
DVD-3000
DVD-3300
DEVICE SELECT : HDP
Blu-Ray preset codes /
Codes préréglés Blu-Ray
Model No. /
Modéle numéro
D
015
095
006, 007, 087, 088, 089, 090,
Citizen
095
Craig
007, 087, 088, 091, 115
006, 049, 073, 080, 087, 088,
Curtis Mathes
091, 115
Cybernex
087
025, 055, 059, 074, 089, 093,
Daewoo
095, 096
Daytron
025, 055
DBX
005, 085
Dumont
053
Dynatech
009
Electrohome
001, 088, 097
Electrophonic
088
001, 009, 017, 027, 086, 088,
Emerson
089, 092, 093, 097, 100, 101,
102, 103, 104, 117
009, 028, 031, 053, 054, 091,
Flsher
099, 115
007, 011, 049, 050, 051, 052,
GE
073, 080, 087
Go Video
047, 048
Goldstar
006, 012, 062, 088, 200
Gradiente
094
Grundig
042
Harley Davidson
094
Harman Kardon
040, 062
Hi-Q
091
009, 013, 023, 026, 058, 108,
Hitachi
109, 110, [111]*
004, 005, 007, 023, 028, 049,
JC Penny
062, 085, 087, 088
Jensen
013, 026
004, 005, 006, 026, 029, 043,
JVC
044, 045, 046, 085
004, 005, 006, 026, 029, 033,
Kenwood
045, 085, 090
Kodak
088
Lloyd
009, 094
LXI
088
Magnavox
015, 016, 042, 049, 063, 106
Magnin
087
004, 005, 006, 015, 042, 049,
Marantz
085, 090
Marta
088
MEI
049
009, 033, 049, 053, 060, 081,
Memorex
087, 088, 091, 094, 115
Metz
123, 124, 125, 126, 127
MGA
001, 017, 027, 041, 097
MGN Technology 087
Midland
011
Minolta
013, 023
001, 003, 008, 013, 014, 017,
Mitsubishi
027, 029, 040, 041, 045, 097
002, 007, 009, 049, 063,
Montgornery Ward 001,
081, 115, 117
Motorola
081
e
Carver
CCE
111
(default /défaut)
DVD-1800BD
DVD-2500BT
DVD-3800BD
DVD-A1UDCI
www.denon.com
Denon Brand Company, D&M Holdings Inc.
Printed in China 5411 10243 007D