ViewSonic PJ1065-2 User guide

PJ1065
User Guide
Guide de l’utilisateur
Bedlenungsanleltung
Guía del usuario
Guida Dell’utente
Användarhandbok
Käyttöopas
使用者指南
使用者指南
Image Size 30” – 300”
XGA LCD Projector
Contents
For Your Records ............................................................................................. 1
FEATURES
BEFORE USE
Contents of Package ........................................................................................ 2
Part Names....................................................................................................... 3
Inserting the Batteries....................................................................................... 5
INSTALLATION
Installation of the Projector and Screen............................................................ 6
Angle Adjustment.............................................................................................. 6
Cabling.............................................................................................................. 7
Power Connection ............................................................................................ 8
Example of System Setup ................................................................................ 8
Plug & Play ....................................................................................................... 8
OPERATIONS
Power ON ........................................................................................................ 9
Power OFF ....................................................................................................... 9
Basic Operation .............................................................................................. 10
Setup Menu .................................................................................................... 12
Input Menu...................................................................................................... 13
Image Menu.................................................................................................... 14
Options Menu ................................................................................................. 15
No Signal Menu .............................................................................................. 16
MAINTENANCE
Lamp............................................................................................................... 17
Air Filters......................................................................................................... 19
Other Maintenance ......................................................................................... 19
TROUBLESHOOTING
OSD Message ................................................................................................ 20
Indicator Message .......................................................................................... 21
Symptom......................................................................................................... 22
Specifications.................................................................................................. 23
Customer Support........................................................................................... 24
LIMITED WARRANTY
VIEWSONIC Projector ................................................................................... 25
Appendix
Power Cord Safety Guidelines........................................................................ 26
FCC Information ............................................................................................. 27
Compliance Information for Canada ............................................................... 27
Compliance Information for European Countries............................................ 27
User Information for All Countries................................................................... 27
ViewSonic PJ1065
i
Copyright © ViewSonic Corporation, 2002. All rights reserved.
Macintosh, Mac and Power Macintosh are registered trademarks of Apple Computer, Inc.
Microsoft, Windows, Windows NT, and the Windows logo are registered trademarks of Microsoft
Corporation in the United States and other countries.
ViewSonic, the three birds logo and OnView are registered trademarks of ViewSonic Corporation.
VESA and SVGA are registered trademarks of the Video Electronics Standards Association. DPMS
and DDC are trademarks of VESA.
VGA, and XGA are registered trademarks of the International Business Machines Corporation.
ENERGY STAR® is a registered trademark of the U.S. Environmental Protection Agency (EPA).
As an ENERGY STAR® partner, ViewSonic Corporation has determined that this product meets the
ENERGY STAR® guidelines for energy efficiency.
Disclaimer: ViewSonic Corporation shall not be liable for technical or editorial errors or omissions
contained herein; nor for incidental or consequential damages resulting from furnishing this
material, or the performance or use this product.
In the interest of continuing product improvement, ViewSonic Corporation reserves the right to
change product specifications without notice. Information in this document may change without
notice.
No part of this document may be copied, reproduced, or transmitted by any means, for any purpose
without prior written permission from ViewSonic Corporation.
Electronic Warranty Registration
To meet your future needs, and to receive any additional product information as it becomes
available, please register your projector's warranty on the Internet at:
http://www.viewsonic.com
Image Optimization files are also available free of charge at our web site. Go to
www.viewsonic.com and select “Support.” If you do not have access to the internet or if you
require further assistance, contact "Customer Support" on page 24.
For Your Records
Product Name:
ViewSonic PJ1065
Model Number:
VPROJ24268-2W
Document Number
A-CD-PJ1065-2
Serial Number:
_______________
Purchase Date:
_______________
Product disposal at end of product life
ViewSonic is concerned about the preservation of our environment. Please dispose of this product
properly at the end of its useful life. Your local waste disposal company may provide information
about proper disposal.
ViewSonic PJ1065
1
FEATURES
This liquid crystal projector is used to project various computer signals as well as NTSC/PAL/
SECAM video signals onto a screen. The installation of this projector requires only a small space,
and large images can be projected easily.
Outstanding Brightness
The UHB lamp and the highly efficient optical system assure a high level of brightness.
Function for Partial Magnification
Interesting parts of images can be magnified for a closer viewing.
Function for Correcting Distortions
Distortion-free images can quickly be adjusted.
BEFORE USE
Contents of Package
Make sure all of the following items are included in the package. If anything is missing, please contact your dealer.
NOTE: Keep the original packing material for future shipment.
Power Cord
(US)
Power Cord
(UK)
Power Cord
(Europe)
Projector
RGB Cable
Component Video Cable
Quick Start Guide
CD-Wizard
Mouse cable
(PS/2)
Batteries
for Remote Control
Device
Remote Control
Device
Carrying Case
2
ViewSonic PJ1065
RCA Video/Audio
Cable
Power Cord
(China)
Part Names
FOCUS Button
ZOOM Button
KEYSTONE Button
INPUT Button
STANDBY/ON Button
MENU Button
RESET Button
LAMP Indicator
TEMP Indicator
POWER Indicator
Control Panel
(refer to page 9, “OPERATIONS”)
Control panel
Remote control sensor
Lens
Ventilation openings
(exhaust)
Filter Cover
(air filter)
Carrying Handle
Foot adjuster
Filter cover
(air filter and intake for the
cooling fan)
Lens cap
Front/right view
Remote control sensor
Foot adjuster
Terminal panel
(see below)
Speaker
Power switch
AC inlet
(to power cord)
Rear/Left view
RGB IN 1 Terminal
RGB IN 2 Terminal
DVI Terminal
S-VIDEO Terminal
RGB OUT Terminal
VIDEO Terminal
CONTROL Terminal
AUDIO IN RGB1/DVI Terminal
AUDIO IN RGB2/Terminal
AUDIO OUT Terminal
AUDIO (MONO)/L
Terminal
AUDIO R Terminal
USB Terminal
Terminal
Panel
COMPONENT VIDEO
Y Terminal
CB/PB Terminal
CR/PR Terminal
ViewSonic PJ1065
3
BLANK Button
STANDBY/ON Button
LASER Button
VIDEO Button
Disk pad
RGB Button
MOUSE/RIGHT Button
Used to operate the
mouse shift function
and left-click function.
Used to click the right
mouse button.
AUTO Button
KEYSTONE Button
MENU Button
RESET Button
MENU SELECT Button
Used to click the left
mouse button.
Button
Used to operate the
mouse shift function.
Used to click the right
mouse button.
PinP Button
FREEZE Button
MUTE Button
POSITION Button
VOLUME Button
ZOOM Button
MAGNIFY Button
FOCUS Button
REMOTE CONTROL DEVICE
(refer to page 9, “OPERATIONS”)
These functions work when the function for controlling the mouse has been activated. The mousecontrolling function will be disabled if POSITION, BLANK ON and MENU ON are selected.
WARNING The laser pointer of the remote control device is used instead of a finger or rod. Be sure to
never look directly into the laser beam outlet or point the laser beam at other persons. The laser beam
may cause serious eye injuries.
CAUTION The use of controls, adjustments or performance of procedures other than those specified
herein may result in an exposure to hazardous radiation.
NOTE: • Always keep the remote control device out of reach of children and pets.
•
•
•
•
•
4
Be sure to protect the remote control device against any physical impact and do not drop it.
Do not place any heavy object on top of the remote control device.
Be sure to protect the remote control device against humidity and do not put it on wet objects.
Do not leave the remote control device close to the cooling fan outlet of the projector.
Do not attempt to disassemble the remote control device.
ViewSonic PJ1065
Inserting the Batteries
Insert the AA batteries into the remote control
device.
1 Remove the battery cover.
Push the knob while lifting up the cover of the
battery compartment.
2 Insert the batteries.
Insert the batteries according to their plus and
minus poles.
3 Replace the cover to the battery compartment.
CAUTION
• Be sure to only use the specified batteries with this remote control device. Do not mix new and
old batteries, since this may result in a cracking or leakage of batteries posing a risk of fire or
leading to personal injury.
• Insert the batteries into the remote control device according to the indicated plus and minus poles.
An incorrect insertion may result in a cracking or leakage of batteries posing a risk of fire or
leading to environmental pollution.
• Before disposing of the batteries, please be sure to observe the respective regulations concerning
the protection of environment in your area.
• Always be sure to keep the batteries out of reach of children or pets.
• If the remote control device will not be used for an extended period of time, remove the batteries
from its battery compartment.
NOTE: • Replace the batteries if the operation of the remote control device becomes irregular or
weak.
ViewSonic PJ1065
5
INSTALLATION
Installation of the Projector and Screen
To set the screen size and projection distance, see the illustration and table below.
The projection distance shown in the table below
Screen
indicates the full size (1024 × 768 dots).
a:Distance from the projector to the screen (± 10%).
b:Distance from the lens center to the bottom of the
screen (± 10%).
Table 1: Reference for Installation
Screen size
[inches (m)]
40 (1.0)
60 (1.5)
80 (2.0)
100 (2.5)
120 (3.0)
150 (3.8)
200 (5.0)
a [inches (m)]
Min.
Max.
55 (1.4)
73 (1.9)
85 (2.2)
114 (2.9)
114 (2.9)
151 (3.8)
144 (3.7)
191 (4.9)
176 (4.5)
231 (5.9)
220 (5.6)
282 (7.2)
291 (7.4)
386 (9.8)
b
[inches (m)]
1 (3)
2 (4)
2 (6)
3 (7)
3 (9)
4 (11)
6 (15)
Top View
Lens center
Side View
CAUTION
• Install the projector in a suitable environment as indicated in this manual.
• If you use a metal tool or the like to mount this unit, be sure to connect it via earth connection so
as to avoid a risk of fire or electric shock.
Connect the ground terminal of the AC inlet of this unit to the ground terminal provided in the
building using an optional three-core power supply cord.
• Always use the liquid crystal projector in a horizontal position, if possible. If you operate the
liquid crystal projector with its lens upwards, its lens downwards or to the side, the heat generated
inside the projector may build up and cause malfunctions or damages. Be especially careful to
never block the ventilation holes.
• Do not install the LCD projector in a smoky surrounding, since smoke residue may be
accumulating on critical parts (i.e. LCD panel, lens, etc.).
Angle Adjustment
Use the foot adjusters located on the bottom of the
projector to adjust the angle of projection. This angle
can be adjusted within approximately 0° to 9°.
1 Lift up the front side of the projector and
press the button of the foot adjuster to adjust
the angle of projection.
2 To lock the foot adjuster at the desired
angle, release the button.
3 Turn the screw of the foot adjuster to
precisely adjust it. Do not use force, since
this could damage the adjuster or result in a
failure of the lock.
Foot Adjusters
Variable within the range of approximately 0°-9°
CAUTION
• Do not release the foot adjuster button unless you hold the projector, or else the projector may
overturn or the fingers may get caught.
6
ViewSonic PJ1065
Cabling
Refer to the table below for connecting each terminal of the projector to each device.
Table 2: Cabling
Terminal
Function
Cable
Analog RGB output
RGB IN 1
RGB IN 2
RGB OUT
Accessory or optional RGB cable with Dsub 15-pin shrink jack and inch thread
screws.
Digital RGB input
DVI
Optional DVI cable with inch thread
screws
Analog RGB input
Audio input
(from the computer)
PS/2 mouse control
ADB mouse control
Serial mouse control
RS/232C communication
USB mouse control
S-video input
Video input
Component video input
AUDIO IN [RGB 1] / [DVI]
(interlocked with RGB IN 1 or DVI)
Optional audio cable with stereo mini-jack
AUDIO IN [RGB 2] / [DVI]
(interlocked with RGB IN 2)
Accessory PS/2 mouse cable
Optional ADB mouse cable
CONTROL
Optional serial mouse cable
Optional RS-232C mouse cable
USB
Optional USB cable
Optional S-video cable with mini DIN 4-pin
S-VIDEO
jack
VIDEO
Accessory video/audio cable
COMPONENT VIDEO Y
COMPONENT VIDEO CB/PB
Accessory component video cable
COMPONENT VIDEO CR/PR
Audio input
(from video equipment)
Audio output
AUDIO (MONO)/L
AUDIO R
AUDIO OUT
Accessory video/audio cable or optional
audio cable with RCA jack
Optional audio cable with stereo mini-jack
CAUTION
• An incorrect connection may result in fire or electric shock. Be sure to read this manual before
connect the projector.
• Be sure to turn off all devices to be connected before you connect the projector.
• The cables may have to be connected with their core set to the projector’s side. Only connect the
cable supplied with the projector or those specified.
NOTE: • Before you connect the projector, be sure to read the manual of the respective device to be
connected. Make sure the projector is compatible with the devices.
• Secure the screws of the connectors and tighten them.
• The optional Mac adapter may be necessary for certain RGB input modes.
• To select the DVI input, the computer may need to be set. For details on how to set the computer
accordingly, refer to the manual of the computer.
• Certain computers may be provided with multiple display modes. The use of such modes may not
be possible with this projector.
• For the pin assignment of the connectors and the RS-232C communication data, refer to the
service manual of PJ1065-2.
• If you use the DVI terminal, the RGB OUT terminal may not work.
ViewSonic PJ1065
7
Power Connection
Be sure to use the correct supplied power cords depending on the power outlet to be connected to.
Connect the AC inlet of the projector firmly to the power outlet with the power cord.
CAUTION
• Be careful when you handle the power cord.
• Firmly connect the power cord. Do not use a loosened or
unsafe power outlet or a malfunctioning contact.
Example of system setup
Computer
(desktop)
Power outlet
AC inlet
Power cord
Computer
(notebook)
S-Video Tape
Recorder
Display
Monitor
Speaker
with
amplifier
DVD Player
Computer (desktop)
NOTE: • When connecting the projector to a notebook computer, set it so as to activate the RGB
external image output (setting it to CRT display or to simultaneous LCD and CRT display). For more
information, refer to the instruction manual of the notebook computer.
Plug & Play
This projector is compatible with VESA DDC 1/2B. Plug & Play is possible by connecting to a computer that is compatible with VESA DDC (Display Data Channel).
Use this function by connecting the accessory RGB cable with RGB IN 1 terminal (DDC 1/2B compatible), or by connecting an optional DVI cable with DVI terminal (DDC 2B compatible). Plug &
Play does not operate by any other connection.
NOTE:
• Plug & Play is a system configured with peripheral equipment including a computer and display,
and an operating system.
• This projector is recognized as a Plug & Play monitor. Use the standard display drivers.
• Plug & Play may not function properly with the computer to be connected. Use the RGB IN 2
terminal if Plug & Play does not function correctly.
8
ViewSonic PJ1065
OPERATIONS
POWER Indicator
STANDBY/ON Button
STANDBY/
ON Button
ZOOM button
FOCUS button
Power Switch
FOCUS button
Lens cap
ZOOM button
Power ON
1 Check if the power cord is connected correctly.
2 Set the power switch to [I]. When the standby mode is selected, the POWER indicator is orange.
3 Press the STANDBY/ON button on the control panel or the remote control device. The warm-up
starts and the POWER indicator blinks green.
4 The POWER indicator stops blinking and turns green when the power is on. Remove the lens
cap.
5 Adjust picture size with the ZOOM button.
6 Adjust focus with the FOCUS button.
Power OFF
1 Press the STANDBY/ON button on the control panel or the remote control device. Then the
message "Power off?" will appear on the screen, and the message will disappear by any operation
or if no operation is carried out for 5 seconds. During this message indication, press the
STANDBY/ON button again. The projector lamp is turned off and the lamp will be cooled down.
The POWER indicator blinks orange when the lamp cools down. Pressing the STANDBY/ON
button has no effect while the POWER indicator is blinking.
2 The system goes into the Standby mode after cooling and the POWER indicator stops blinking
and changes to orange. Check if the indicator is orange and set the power switch to [0].
3 The POWER indicator goes out when the power is switched off. Attach the lens cap.
WARNING: Before using this equipment, read this manual thoroughly. Always ensure that the
equipment is used safely.
NOTE: • Except in emergencies, follow the above-mentioned procedure for turning the power off.
Any incorrect procedure will shorten the life of the projector lamp and LCD panel.
• To prevent any trouble, turn on/off the projector when the computer or video tape recorder is OFF.
Providing a RS-232C cable is connected, turn on the computer before switching on the projector.
• If the projector continues projecting the same image, the image may remain as an after-image. Do
not project the same image for a long time.
ViewSonic PJ1065
9
Basic Operation
The basic operations shown in Table 3 can be performed with the supplied remote control device or
by way of the projector’s control panel. Items indicated by (*) may be used from the control panel.
Table 3: Basic Operation
Item
Description
INPUT
SELECT
Select Input Signal (*): Press the INPUT button.
RGB IN 1→RGB IN 2→DVI
→VIDEO→S-VIDEO→COMPONENT VIDEO (→RGB IN 1)
Select RGB Input: Press the RGB button.
VIDEO/S-VIDEO/COMPONENT VIDEO→RGB IN 1/RGB IN 2/DVI
RGB IN 1→RGB IN 2→DVI (→RGB IN 1)
Select Video Input: Press the VIDEO button.
RGB IN 1/RGB IN 2/DVI→VIDEO/S-VIDEO/COMPONENT VIDEO
VIDEO→S-VIDEO→COMPONENT VIDEO (→VIDEO)
• The selected signal name is displayed for approximately 3 seconds when the
input signal is changed.
POSITION
Set/Clear Position Adjustment Mode: Press the POSITION button.
The [ ] icon is displayed in the POSITION mode.
Image Position Adjustment: Press the
and
buttons in the
POSITION mode.
• Valid only in the MAGNIFY mode if a video signal is input.
• After approximately 10 seconds of inactivity the [ ] icon is extinguished and the
POSITION mode will be cleared automatically.
•
and
buttons may operate as the mouse control button. See page 4.
RESET (*)
Initialize Each Item: Select an item and press the RESET button.
Initialize Position Adjustment: Press the RESET button and the
POSITION mode. This function is valid only if a RGB signal is the input.
• Valid except for the VOLUME, LANGUAGE, WHISPER and H PHASE.
• The RESET button may operate as the mouse control button. Refer to page 4.
MAGNIFY
Set MAGNIFY Mode: Press the MAGNIFY
button.
Move Magnified Area: Run the POSITION in the MAGNIFY mode.
Adjust Magnification: Press the MAGNIFY
button in MAGNIFY mode.
Clear MAGNIFY Mode: Press the MAGNIFY
button.
• The MAGNIFY mode is cleared by running or setting the AUTO, ASPECT, INPUT
SELECT or VIDEO, or by changing the input signal.
FREEZE
Set/Clear FREEZE Mode: Press the FREEZE button. The [ ] icon is displayed,
and the image will be frozen in the FREEZE mode.
• The FREEZE mode is cleared by running or setting POSITION, VOLUME, MUTE,
Automatic Adjustment, BLANK ON/OFF, or MENU ON/OFF, or by changing the
input signal.
• Do not forget to clear frozen static images.
NOTE: • Use the remote control device at a distance of approximately 5 m from the sensor on the
front of the projector, and within a range of 30 °left-right. Strong light and obstacles will interfere
with the operation of the remote control device.
10
ViewSonic PJ1065
Items indicated by (*) may be used with the control panel.
Table 3: Basic Operation (continued)
Item
Description
VOLUME
Volume Adjustment: Press the VOLUME
MUTE
Set/Clear Mute Mode: Press the MUTE button. No sound is heard in the MUTE
mode.
AUTO
Automatic Adjustment at RGB Input: Press the AUTO button. Horizontal
position(H. POSIT), vertical position (V. POSIT), clock phase (H. PHASE), and
horizontal size(H. SIZE) are automatically adjusted. Use with the window at
maximum size in the application display.
Automatic Adjustment at Video Input: Press the AUTO button. A signal type
appropriate for the input signal is selected automatically. Valid only when AUTO
is set for VIDEO on the menu.
• This operation requires approximately 10 seconds. It may not function correctly
with some input signals.
BLANK ON/
OFF
Set/Clear Blank Mode: Press the BLANK button. No image is displayed in the
Blank mode.
MENU ON/
OFF (*)
Menu Display Start/Stop: Press the MENU button.
• The menu display is terminated automatically after approximately 10 seconds
of inactivity.
MENU
SELECT
button.
Select Menu Type: Press the MENU SELECT button. Allows the user to select
the normal menu or the single menu. Only the selected item is displayed on the
single menu, and other items are displayed with the
and
buttons as with
the normal menu.
• Valid only when the Setup menu is used. Push the MENU SELECT button after
selecting items such as "BRIGHTNESS".
• The MENU SELECT button may operate as the mouse control button. Refer to
page 4.
Normal menu
Single menu
(MENU SELECT)
P.IN P.
MODE
Select Mode of P.IN P. Display: Press the PinP button.
Small→Large→P.IN P. off (→Small)
• Valid only at RGB IN 1, RGB IN 2 or DVI input.
ZOOM (*)
Adjust Screen Size: Press the ZOOM
FOCUS (*)
Adjust Focus: Press the FOCUS
KEYSTONE
(*)
Set / Clear KEYSTONE Mode: Press the KEYSTONE
button.
Select KEYSTONE Mode: Press the
button in the KEYSTONE mode.
Vertical
Horizontal
Adjust KEYSTONE: Press the
button.
button.
button.
ViewSonic PJ1065
11
Setup Menu
The following adjustments and settings are possible when SETUP is selected at the top of the
menu. Part of the Setup menu differs between
RGB input and video input. Select an item with
the and
buttons, and start operation. Use
the Single menu to reduce menu size (see Table
3, MENU SELECT).
RGB IN 1
RGB IN 2
DVI
VIDEO
S-VIDEO
COMPONENT VIDEO
Table 4: Setup Menu
Item
Description
RGB IN 1
RGB IN 2
DVI
VIDEO
S-VIDEO
COMPONENT
√
√
−
−
√
√
−
−
BRIGHT
Adjustment: Dark
CONTRAST
Adjustment: Weak
Strong
V POSIT
Adjustment: Down
Up
H POSIT
Adjustment: Left
Right
√
√
√
√
H PHASE
Adjustment: Left
Right
• Adjust to eliminate flicker.
√
−
√
H SIZE
Adjustment: Small
Large
• The image may not be displayed correctly if the
horizontal size is excessive. In such cases, press the
RESET button, and initialize the horizontal size.
√
−
−
SHARPNESS
Adjustment: Soft
Clear
COLOR
Adjustment: Light
Dark
−
−
−
−
√
√
TINT
Adjustment: Red
Green
• Valid only when NTSC or NTSC 4.43 signal is
received.
−
−
√
√
√
√
√
√
√
√
√
−
−
−
√
Light
COLOR BAL R Adjustment: Light
Dark
COLOR BAL B Adjustment: Light
Dark
Select Image Aspect Ratio:
Select position of image:
Press the
button when 16:9 [
] has been
selected.
Down→
Up (→Center
)
Center→
Select Image Aspect Ratio:
ASPECT
12
small[
]
Select position of image:
Press the
button when 16:9 [
] / 4:3 small [
]
has been selected.
Center→
Down→
Up (→Center
)
• 4:3 small cannot be selected with the input of 720P
or 1080i component.
• 4:3 small may not be displayed correctly with some
input signals.
ViewSonic PJ1065
Input Menu
The following functions are available when INPUT is selected on the
menu. Select an item with the and
buttons, and start or stop operation
with the
and
buttons. The function indicated (**) are effective on
video input mode, the P.IN P. window on RGB input mode.
Table 5: Input Menu
Item
Description
AUTO
Automatic Adjustment at RGB Input: Select the EXECUTE with the
button.
Horizontal position (H.POSIT), vertical position (V.POSIT), clock phase
(H.PHASE), and horizontal size (H.SIZE) are automatically adjusted. Use with
the window at maximum size in the application display.
Automatic Adjustment at Video Input: Select the EXECUTE with the
button. A signal type appropriate for the input signal will be selected
automatically. Valid only when AUTO is set for VIDEO on the menu.
• This operation requires approximately 10 seconds. It may not function correctly
with some input signals. Pressing the AUTO button in this case may correct this
problem.
• This function is the same as for the AUTO function in Basic operation.
RGB
Displays RGB Input Frequency: Displays the horizontal and vertical sync
signal frequencies for RGB input.
• Valid only at RGB input.
VIDEO (**)
Select Video Signal Type: Select the signal type with the
and
buttons.
Select NTSC, PAL, SECAM, NTSC4.43, M-PAL, or N-PAL as appropriate for the
input signal. The selection of AUTO enables and executes the function AUTO
(Automatic Adjustment at Video Input), except for the N-PAL input.
• Use this function when the image becomes unstable (eg. the image becomes
irregular, or lacks color) at VIDEO/S-VIDEO input.
• Automatic Adjustment requires approximately 10 seconds. It may not function
correctly with some input signals. Pressing the AUTO button in this case may
correct this problem except for the N-PAL input.
• For the COMPONENT VIDEO input, this function is not effective and the signal
type is distinguished automatically.
VIDEO NR
(**)
Set/Clear Noise Reduction Mode: Select the TURN ON / TURN OFF with the
button. When the TURN ON is selected, the NR mode is active and the
noise on screen of the video input will be reduced.
• Valid except for the HDTV.
Progressive
(**)
Select Progressive Mode: Select the mode suitable for the input signal with the
buttons. The TV mode and the FILM mode convert the interlaced video
signal into the progressive signal. The FILM mode is adaptable 2-3 Pull-Down
system to the conversion.
• Use this function to raise resolution, at the interlaced video input except HDTV
signal.
BLACK **)
Set/Clear Black Enhancement Mode: Select the TURN ON / TURN OFF with
the
button. When the TURN ON is selected, the black enhancement
mode is active and the contrast ratio of the screen for the video input will be
raised by making black level darker.
HDTV (**)
Select HDTV mode: Select the 1035i mode or 1080i mode suitable for the input
signal with the
button.
ViewSonic PJ1065
13
Image Menu
The following adjustments and settings are available when IMAGE is
selected on the menu. Select an item with the
and
buttons, and start
or stop operation with the and
buttons.
Table 6: Image Menu
Description
Item
BLANK
Select Blank Screen: Select the screen with the
/
button. The selected one
(MyScreen, ORIGINAL or one colors) is displayed when the BLANK mode is ON.
MyScreen is a mode that the customer-customized screen is displayed. This is
the blue screen at the factory setting. Refer to the description of MyScreen below.
ORIGINAL is a mode that the factory fixed screen is displayed.
• When MyScreen or ORIGINAL is selected, the screen is going blank after
several minutes.
START UP
Select Start Up Screen: Select the screen in case of no signal input with the
/
button. The selected one (MyScreen, ORIGINAL or TURN OFF) is displayed
when no signal is input
MyScreen is a mode that the customer-customized screen is displayed. This is
the blue screen at the factory setting. Refer to the description of MyScreen below.
ORIGINAL is a mode that the factory fixed screen is displayed.
TURN OFF displays the blue screen.
• When MyScreen or ORIGINAL is selected, the screen is going blank after
several minutes.
MyScreen
Set MyScreen Mode: Select the EXECUTE with the
button to display the
MyScreen menu and set the MyScreen mode for BLANK and START UP
functions.
ESC clears and closes the menu box.
NORM. is default of the MyScreen menu.
FREEZE freezes the image and displays the frame to capture.
Press the button after freeze to go to the MyScreen Capture Position mode.
,
,
and
allow to
In the MyScreen Capture Position mode, the buttons
move the frame to capture.
After adjusting the position, press the KEYSTONE button to go to the MyScreen
Display Size mode.
To cancel freezing and return to the NORM. Mode of the MyScreen menu, press
the RESET button.
In the MyScreen Display Size mode, select the magnification x1, x2 or FULL with
the button
.
After selecting the magnification, press the KEYSTONE button to go to the CAPT.
mode and start capturing.
To return to the MyScreen Capture Position mode, press the RESET button.
CAPT. executes a capturing the image. It requires about 20 seconds. After
capturing, the captured image will be displayed for about 10 seconds.
MIRROR
Select Mirror Status: Select mirror status with
button.
Select Position of P. in P. Display: Press the
button.
P. IN P.
POSIT
• Valid only at RGB IN 1, RGB IN 2 or DVI input.
P. IN P.
INPUT
Select signal of P. in P. Display: Press the
button.
VIDEO
S-VIDEO
COMPONENT
GAMMA
Select Gamma Mode: Select the gamma mode with the
NORMAL
CINEMA
DYNAMIC
14
ViewSonic PJ1065
button.
Options Menu
The following adjustments and settings are available when OPT. is
selected on the menu. Select an item with the and
buttons, and start
operation.
Table 7: Options Menu
Item
Description
VOLUME
Volume Adjustment: Reduce VOLUME
MENU
COLOR
Select Menu Background Color: Select with the
and
buttons.
LANGUAGE
Operation Start/Stop: Press the
button.
Select Menu Display Language: Select with the
and
buttons.
AUTO OFF
Operation Start/Stop: Press the
button.
Set AUTO OFF: Set 1-99 minutes with the
and
buttons. The system
automatically enters the standby mode when a signal is not received for the set
time.
Clear AUTO OFF: Select STOP (0 min.) with the
button. When STOP is
selected the system does not enter the standby mode even if no signal is
received.
SYNC ON G
Operation Start/Stop: Press the
button.
SYNC ON G Valid: Select TURN ON with the
button.
SYNC ON G Invalid: Select TURN OFF with the
button.
• May not be displayed correctly with some input signals when SYNC ON G is
valid. In such cases, remove the signal connector so that no signal is received,
set SYNC ON G to invalid, and reconnect the signal.
WHISPER
Set / Clear WHISPER Mode: Press the
button. When WHISPER is
selected, the WHISPER mode is active. In the WHISPER mode, acoustic noise
level from the unit is reduced, and brightness level on screen is a little lower.
Increase VOLUME
ViewSonic PJ1065
15
No Signal Menu
The same adjustments and settings are available as with the Image and
Options menus when the MENU button is pressed during display of the
“NO INPUT IS DETECTED ON***”or “SYNC IS OUT OF RANGE
ON***”message while no signal is received.
Table 8: No Signal Menu
Description
Item
VOLUME
Volume Adjustment: Reduce VOLUME
Increase VOLUME
• When this function is used, audio input is automatically switched to video. The
audio input can be switched by moving the DISK PAD left and right during the
display of the volume adjustment bar. The volume adjustment bar is displayed by
pressing VOLUME
or VOLUME
button.
BLANK
Select Blank Screen: Select the screen with the
/
button.The selected one
(MyScreen, ORIGINAL or one colors) is displayed when the BLANK mode is ON.
MyScreen is a mode that the customer-customized screen is displayed. This is
the blue screen at the factory setting. Refer to the description of MyScreen below.
ORIGINAL is a mode that the factory fixed screen is displayed.
• When MyScreen or ORIGINAL is selected, the screen is going blank after
several minutes.
START UP
Select Start Up Screen:Select the screen in case of no signal input with the
/
button. The selected one (MyScreen, ORIGINAL or TURN OFF) is displayed
when no signal is input
MyScreen is a mode that the customer-customized screen is displayed. This is
the blue screen at the factory setting. Refer to the description of MyScreen below.
ORIGINAL is a mode that the factory fixed screen is displayed.
TURN OFF displays the blue screen.
• When MyScreen or ORIGINAL is selected, the screen is going blank after
several minutes.
MIRROR
Operation Start/Stop: Press the
button.
Select Mirror Status: Select the mirror status with the
and
MENU COLOR Select Menu Background Color: Select the color with the
buttons.
and
buttons.
LANGUAGE
Operation Start/Stop: Press the
button.
Select Menu Display Language: Select the language with the
AUTO OFF
Operation start/stop: Press the
button.
Set AUTO OFF: Set 1-99 minutes with the
and
buttons. The system
automatically enters the standby mode when a signal is not received for the set
time.
Clear AUTO OFF: Select the STOP (0 min.) with the
button. When STOP is
selected the system does not enter the standby mode even if no signal is
received.
SYNC ON G
Operation Start/Stop: Press the
button.
SYNC ON G Valid: Select the TURN ON with the
button.
SYNC ON G Invalid: Select the TURN OFF with the
button.
• May not be displayed correctly with some input signals when the SYNC ON G is
valid. In such cases, remove the signal connector so that no signal is received,
set the SYNC ON G to invalid, and reconnect the signal.
WHISPER
Set / Clear WHISPER Mode: Press the
button. When WHISPER is
selected, the WHISPER mode is active. In the WHISPER mode, acoustic noise
level from the unit is reduced, and brightness level on screen is a little lower.
16
ViewSonic PJ1065
and
buttons.
MAINTENANCE
Lamp
HIGH VOLTAGE
HIGH TEMPERATURE
HIGH PRESSURE
Contact your dealer before replacing the lamp.
For the lamp replacement, see the item “Optional Parts” of the Table 12.
Before replacing the lamp, switch power OFF, remove the power cord from the power outlet, and
wait approximately 45 minutes until the lamp has cooled. The lamp may explode if handled at high
temperatures.
WARNING:
•
•
•
•
For disposal of used lamp, treat according to the instruction of community authorities.
Since the lamp is made of glass, do not apply shock to it and do not scratch it.
Also, do not use old lamp. This could also cause explosion of the lamp.
Premature lamp failure MAY be caused by an electronic component in the projector and not
necessarily the lamp. If unsure contact your local service center.
• If it is probable that the lamp has exploded (explosive sound is heard), disconnect the power plug
from the power outlet and ask your dealer to replace lamp. The lamp is covered by front glass,
but, in rare cases, the reflector and the inside of the projector may be damaged by scattered
broken pieces of glass, and broken pieces could cause injury when being handled.
• Do not use the projector with the lamp cover removed.
Lamp
Reflector
Front glass
Lamp Life
Projector lamps have a finite life. The image will become darker, and hues will become weaker, after
a lamp has been used for a long period of time. Replace the lamp if the LAMP indicator is red, or the
CHANGE THE LAMP message appears when the projector is switched ON. See Table 9 on p. 20
and Table 10 on p. 21.
NOTE: • The LAMP indicator is also red when the lamp unit reaches high temperature. Before
replacing the lamp, switch power OFF, wait approximately 20 minutes, and switch power ON again.
If the LAMP indicator is still red, replace the lamp.
ViewSonic PJ1065
17
Replacing the Lamp
1 Switch the projector OFF, remove the power cord from the power
outlet, and wait at least 45 minutes for the unit to cool.
2 Prepare a new lamp.
3 Check that the projector has cooled sufficiently, and gently turn it
4
5
6
7
8
upside down.
Loosen the screw as shown in the diagram, and remove the lamp
cover.
Loosen the two screws, and gently remove the lamp while holding
the grips. Touching the inside of the lamp case may result in
uneven coloring.
Install the new lamp and tighten the two screws firmly. Also
steadily push the opposite side of the screwed lamp into the unit.
Replace the lamp cover in position and tighten the screw firmly.
Gently turn the projector right-side up.
CAUTION
• Ensure that screws are tightened properly. Screws not tightened
fully may result in injury or accidents.
• Do not use the projector with the lamp cover removed.
Resetting the Lamp Timer
Reset the lamp timer after replacing the lamp. When the lamp has been replaced after the LAMP
indicator is red, or the CHANGE THE LAMP message is displayed, complete the following operation within ten minutes of switching power ON. The power will be turned off automatically if over
10 minutes.
1 Switch power ON, and press the RESET button, for approximately three seconds. The ‘LAMP
xxxx hr’ message will appear on the lamp timer on the bottom of the screen.
2 Press the MENU button on the remote control transmitter, or the RESET button on the control
panel, while the lamp timer is displayed. The ‘LAMP xxxx □ → 0 ■ CANCEL’ message will
then appear.
and select 0,and wait until the timer display is cleared.
3 Press the
NOTE: • Do not reset the lamp timer without replacing the lamp. Reset the lamp timer always when
replacing the lamp. The message functions will not operate properly if the lamp timer is not reset
correctly.
18
ViewSonic PJ1065
Air Filters
Cleaning Air Filters
filter cover
This projector uses 2 air filters. These air filters should be
cleaned as described below at intervals of approximately 100
hours.
1 Switch the projector power supply OFF, and remove the
power cord from the power outlet.
2 Remove the filter cover and the air filter.
3 Clean the air filter with a vacuum cleaner.
4 Set the air filter and the filter cover.
filters
Replacing the Air Filter
Replace the air filter if contamination cannot be removed, or if it is damaged. Contact your dealer in
such case.
1 Switch the projector power supply OFF, and remove the power cord from the power outlet.
2 Remove the filter cover and the old filter.
3 Set the new filter and the filter cover.
CAUTION
• Switch power OFF and remove the power cord from the power outlet before beginning
maintenance work.
• Replace the air filter if contamination cannot be removed, or if it is damaged.
• Do not use the equipment with the air filter removed.
• When the air filter is clogged with dust etc., the power supply is switched OFF automatically to
prevent the temperature rising inside the projector.
Other Maintenance
Maintenance Inside the Equipment
For safety reasons, ensure that the equipment is cleaned and checked by the dealer once every two
years. Maintaining the equipment by yourself is dangerous.
Cleaning the Lens
Gently wipe the lens with lens cleaning paper. Do not touch the lens with your hands.
Cleaning the Cabinet and Remote control transmitter
Gently wipe with a soft cloth. If dirt and stains etc. are not easily removed, use a soft cloth dampened
with water, or water and a neutral detergent, and wipe dry with a soft, dry cloth.
CAUTION
• Switch power OFF and remove the power cord from the power outlet before beginning
maintenance work.
• Do not use detergents or chemicals other than those noted above (e.g. benzene or thinners).
• Do not use cleaning sprays.
• Do not rub with hard materials, or tap the equipment.
ViewSonic PJ1065
19
TROUBLESHOOTING
OSD Message
The messages as described below may appear on the screen at power ON. Take the appropriate measures when such messages appear.
Table 9: OSD Message
Message
Contents
CHANGE THE LAMP
AFTER REPLACING LAMP,
RESET THE LAMP TIME.
(*1)
The usage time of lamp will be reaching 2000 hr shortly (*2).
It is recommended to replace the lamp soon. Prepare a new lamp
as replacement.
CHANGE THE LAMP
AFTER REPLACING LAMP,
RESET THE LAMP TIME.
THE POWER WILL TURN
OFF
AFTER **hr.
(*1)
The usage time of lamp will be reaching 2000 hr shortly.
It is recommended to replace the lamp within * * hours (*2).
It might happen that the lamp is cut off before * * hr by any
chance. Power will be switched OFF automatically in * * hours.
Replace the lamp as shown on p. 17-18, “Lamp.” Always reset
the lamp timer after replacing the lamp.
CHANGE THE LAMP
AFTER REPLACING LAMP,
RESET THE LAMP TIME.
THE POWER WILL
TURN OFF
AFTER 0 hr.
The usage time of lamp is about to reach. Power will be switched
OFF in a few minutes (*2).
Switch power OFF immediately and replace the lamp as shown
on p. 17-18, “Lamp.” Always reset the lamp timer after replacing
the lamp.
NO INPUT IS DETECTED
ON ***
No input signal found.
Check the signal input connections and signal sources.
SYNC IS OUT OF RANGE
ON ***
The horizontal or vertical frequency of the input signal is not
within the specified range.
Check the specifications of the equipment and the signal source.
CHECK THE AIR FLOW
The internal temperature has risen.
Switch power OFF, and wait 20 minutes until the equipment cools
down.
Check the following and Switch power ON again.
* Are the ventilation openings blocked.
* Is the air filter dirty.
* Is the ambient temperature higher than 35°C.
NOTE:
(*1) This message is cleared automatically after approximately three minutes, and appears every
time power is switched ON.
(*2) The unit has a function to turn the power off which will be active when the usage time reaches
2000 hr. However the life of lamp might be much different, so that it might happen that a lamp is cut
off before the function is active.
20
ViewSonic PJ1065
Indicator Message
The POWER indicator, LAMP indicator, and TEMP indicator are lit and blank as follows. Take the
appropriate measures.
Table 10: Indicator Message
POWER
indicator
LAMP
indicator
TEMP
indicator
Lit
orange
Turns off
Turns off
The Standby mode has been set.
Blinks
green
Turns off
Turns off
Warming up. Please wait.
Lit
green
Turns off
Turns off
ON. Normal operation possible.
Blinks
orange
Turns off
Turns off
Cooling down. Please wait.
Turns off
Lamp is not lit.
The interior of the equipment may be too hot. Switch power
OFF, wait 20 minutes until the equipment cools, and check
whether the ventilation openings are blocked, whether the air
filter is dirty, or whether the ambient temperature exceeds 35
°C. And switch power ON again. Replace the lamp if the same
problem occurs.
Turns off
Lamp or lamp cover is not found, or hasn’t been fitted in
correctly.
Switch power OFF, and wait for 45 minutes until the equipment
cools. Check fitting of the lamp and lamp cover, and switch
power ON again. Contact your dealer if the same problem
occurs again.
Blinks
red
The cooling fan is not operating.
Switch power OFF, and wait for 20 minutes until the equipment
cools. Check for foreign matters in the fan, and switch power
ON again. Contact your dealer if the same problem occurs
again.
Lit red
The interior of the equipment is too hot.
Switch power OFF, and wait for 20 minutes until the equipment
cools. Check whether the ventilation openings
are blocked, whether the air filter is dirty, or whether the ambient
temperature exceeds 35 °C. Then switch power
ON again. Contact your dealer if the same problem occurs
again.
Lit red
Lit red
Lit red
Lit red
Lit red
Blinks
red
Turns off
Turns off
Contents
NOTE: • When the internal temperature becomes excessive, power is switched OFF automatically
for safety reasons, and the indicator is extinguished. Set the power switch to [O] and wait for 20
minutes until the equipment has cooled sufficiently.
ViewSonic PJ1065
21
Symptom
Before requesting repair, please check in the following chart. If the situation cannot be corrected,
then contact your dealer.
Table 11: Symptom
Symptom
The power is not
turned on.
No video or audio.
Video is present but
no audio.
Audio is present but
no video.
Colors are pale and
color matching is
poor.
Images are dark.
Video is blurred.
22
Possible cause
Remedy
Page
The main power switch is
not turned on.
Turn on the main power switch.
The power cord is
disconnected.
Plug the power cord into an AC
power outlet.
The input is not correctly
set.
Use the projector or remote
control transmitter to set.
10
No signal input.
Connect correctly.
7, 8
The projector is not
correctly connected.
Connect correctly.
7, 8
The volume is set to
minimum.
Press VOLUME
on the remote
control or display the menu
screen and adjust the volume.
Mute is turned on.
Press the MUTE
The projector is not
correctly connected.
Connect correctly.
7, 8
The brightness adjustment
knob is rotated fully
clockwise.
Select BRIGHT with the MENU
button and the press the button.
12
The lens cap is still
attached.
Remove the lens cap.
9
Color density and color
matching are not correctly
adjusted.
Adjust the video.
12
Brightness and contrast
are not correctly adjusted.
Adjust the video.
12
The lamp is approaching
the end of its service life.
Replace with a new lamp.
17
Focus or H PHASE is out
of adjustment.
Adjust the focus or H PHASE.
ViewSonic PJ1065
button.
8, 9
11, 15
11
9, 12
SPECIFICATIONS
Table 12: Specifications
Item
Panel size
Liquid crystal
Drive system
projector
Pixels
Lens
Lamp
Speaker
Power supply
Power consumption
Temperature range
Size
Weight (mass)
Specification
1
RGB IN
RGB signal
input
2
DVI
AUDIO IN
RGB1
DVI
RGB2
Y
CB/PB
CR/PR
0.7 Vp-p, 75 Ω Terminator (positive)
S-VIDEO
COMPONENT
VIDEO
AUDIO
RGB OUT
Signal output
AUDIO OUT
Control
functions
Optional parts
CONTROL
USB
200m Vrms, 50 kΩ (max. 3.0Vp-p)
Stereo mini jack
1.0Vp-p, 75 Ω terminator
RCA jack
Brightness signal: 1.0 Vp-p, 75 Ω terminator
Color signal: 0.286Vp-p (burst signal), 75 Ω terminator
Mini DIN 4-pin jack
1.0 Vp-p, 75 Ω Terminator (positive)
0.7 Vp-p, 75 Ω Terminator (positive)
VIDEO
Video signal
input
3.3 cm (1.3 type)
TFT active matrix, 1024 × 768 native
786,432 pixels (1024 horizontal × 768 vertical)
Zoom lens F = 1.7 – 2.3; f = 49.0 – 64.0 mm
275 W UHB
1.2 W + 1.2 W (stereo)
AC 100 – 120 V, 4.7 A / AC 220 – 240 V, 2.0 A
440 W
0 – 35°C (operating)
289 (W) × 139 (H) × 345 (D) mm
6.5 kg
Video: Analog 0.7 Vp-p, 75 Ω terminator (positive)
H/V. sync.: TTL level (positive/negative)
Composite sync.: TTL level
D-sub 15-pin shrink jack
TMDS, DC: 150-1200 mV / AC: 1.56 Vp-p
TTL Level (Positive/Negative)
L/MONO 200m Vrms, 50 kΩ (max. 3.0 Vp-p)
RCA jack
R
Video: Analog 0.7 Vp-p, 75 Ω output impedance (positive)
H/V. sync.: TTL level (positive/negative)
Composite sync.: TTL level
D-sub 15-pin shrink jack
200m Vrms, output impedance 1 kΩ (max. 3.0Vp-p)
Stereo mini jack
D-sub 15-pin shrink plug
USB jack (B type)
Lamp: PRJ-RLC--002
NOTE: • These specifications are subject to change without notice.
ViewSonic PJ1065
23
Customer Support
For technical support or product service, see the table below or contact your reseller.
NOTE: You will need the product serial number.
Country/Region
Web site
T = Telephone
F = FAX
Email
United States
viewsonic.com/support
T: (800) 688-6688
F: (909) 468-1202
service.us@
viewsonic.com
Canada
viewsonic.com/support
T: (800) 688-6688
F: (909) 468-1202
service.ca@
viewsonic.com
United Kingdom
viewsoniceurope.com
T: 0800 833 648
F: (01293) 643910
service.eu@
viewsoniceurope.com
Europe, Middle East, Baltic countries, and
North Africa
viewsoniceurope.com
Contact your reseller service.eu@
viewsoniceurope.com
Australia and New Zealand
viewsonic.com.au
T: +61 2 9929 3955
F: +61 2 9929 8393
service.au@
viewsonic.com
Singapore/India and Southeast Asia
viewsonic.com.sg
T: 65 273 4018
F: 65 273 1566
service.sg@
viewsonic.com
Other Asia/Pacific countries
viewsonic.com.tw
T: 886 2 2246 3456
F: 886 2 8242 3668
service.ap@
viewsonic.com
South Africa
viewsonic.com/asia
T: 886 2 2246 3456
F: 886 2 8242 3668
service.ap@
viewsonic.com
24
ViewSonic PJ1065
LIMITED WARRANTY
VIEWSONIC Projector
What the warranty covers:
ViewSonic® warrants its products to be free from defects in material and workmanship during the warranty period. If a
product proves to be defective in material or workmanship during the warranty period, ViewSonic will at its sole option
repair or replace the product with a like product. Replacement product or parts may include remanufactured or refurbished
parts or components.
How long the warranty is effective:
ViewSonic projectors are warranted for two (2) years for all parts excluding the lamp, two (2) years for all labor, and ninety
(90) days for the lamp from the date of the first consumer purchase.
Who the warranty protects:
This warranty is valid only for the first consumer purchaser.
What the warranty does not cover:
1.
2.
Any product on which the serial number has been defaced, modified or removed.
Damage, deterioration or malfunction resulting from:
a. Accident, misuse, neglect, fire, water, lightning, or other acts of nature, unauthorized product modification, or failure to follow
instructions supplied with the product.
b. Repair or attempted repair by anyone not authorized by ViewSonic.
c. Any damage of the product due to shipment.
d. Removal or installation of the product.
e. Causes external to the product, such as electric power fluctuations or failure.
f. Use of supplies or parts not meeting ViewSonic’s specifications.
g. Normal wear and tear.
h. Any other cause which does not relate to a product defect.
3.
Removal, installation, and set-up service charges.
How to get service:
1.
2.
3.
4.
For information about receiving service under warranty, contact ViewSonic Customer Support. You will need to provide your
product’s serial number.
To obtain warranted service, you will be required to provide (a) the original dated sales slip, (b) your name, (c) your address, (d) a
description of the problem, and (e) the serial number of the product.
Take or ship the product freight prepaid in the original container to an authorized ViewSonic service center or ViewSonic.
For additional information or the name of the nearest ViewSonic service center, contact ViewSonic.
Limitation of implied warranties:
THERE ARE NO WARRANTIES, EXPRESS OR IMPLIED, WHICH EXTEND BEYOND THE DESCRIPTION
CONTAINED HEREIN INCLUDING THE IMPLIED WARRANTY OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE.
Exclusion of damages:
VIEWSONIC’S LIABILITY IS LIMITED TO THE COST OF REPAIR OR REPLACEMENT OF THE PRODUCT.
VIEWSONIC SHALL NOT BE LIABLE FOR:
1.
2.
3.
DAMAGE TO OTHER PROPERTY CAUSED BY ANY DEFECTS IN THE PRODUCT, DAMAGES BASED UPON
INCONVENIENCE, LOSS OF USE OF THE PRODUCT, LOSS OF TIME, LOSS OF PROFITS, LOSS OF BUSINESS
OPPORTUNITY, LOSS OF GOODWILL, INTERFERENCE WITH BUSINESS RELATIONSHIPS, OR OTHER COMMERCIAL LOSS,
EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
ANY OTHER DAMAGES, WHETHER INCIDENTAL, CONSEQUENTIAL OR OTHERWISE.
ANY CLAIM AGAINST THE CUSTOMER BY ANY OTHER PARTY.
Effect of state law:
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. Some
states do not allow limitations on implied warranties and/or do not allow the exclusion of incidental or consequential
damages, so the above limitations and exclusions may not apply to you.
Sales outside the U.S.A. and Canada:
For warranty information and service on ViewSonic products sold outside of the U.S.A. and Canada, contact ViewSonic
or your local ViewSonic dealer.
Projector Warranty (V2.1)
Release Date: 04-18-2001
ViewSonic PJ1065
25
Appendix
Power Cord Safety Guidelines
Caution: Use a power cable that is properly grounded. Always use an AC power cord that meets your country’s safety
standard.
USA .............................. UL
Canada......................... CSA
Germany....................... VDE
Switzerland ...................SEV
Britain............................BASE/BS
Japan ............................Electric Appliance Control Act
AC PLUG CORD PRECAUTIONS FOR THE UNITED KINGDOM
FOR YOUR SAFETY PLEASE READ THE FOLLOWING TEXT CAREFULLY.
IF THE FITTED MOULDED PLUG IS UNSUITABLE FOR THE SOCKET OUTLET THEN THE PLUG
SHOULD BE CUT OFF AND DISPOSED OF SAFELY.
THERE IS A DANGER OF SEVERE ELECTRICAL SHOCK IF THE CUT OFF PLUG IS INSERTED INTO AN
APPROPRIATE SOCKET.
If a new plug is to be fitted, please observe the wiring code as shown below.
If in any doubt, please consult a qualified electrician.
WARNING: THIS APPLIANCE MUST BE EARTHED.
IMPORTANT: The wires in this mains lead are coloured in accordance with the following code:
Green-and-Yellow: Earth
Blue:
Neutral
Brown:
Live
If the coloured wires of the mains lead of this appliance do not correspond with the coloured markings
identifying the terminals in your plug, proceed as follows:
The wire which is coloured GREEN-AND-YELLOW must be connected to the terminal in the plug which is
marked by the letter E or by the Earth symbol or coloured GREEN or GREEN-AND-YELLOW.
The wire which is coloured BLUE must be connected to the terminal in the plug which is marked with the letter
N or coloured BLACK. The wire which is coloured BROWN must be connected to the terminal in the plug
which is marked with the letter L or coloured RED.
IMPORTANT NOTICE CONCERNING POWER CORD SELECTION
The power cord set for this unit has been enclosed and has been selected according to the country of
destination and must be used to prevent electric shock. Use the following guidelines if it is necessary to
replace the original cord set, or if the cord set is not enclosed.
The female receptacle of the cord set must meet CEE-22 requirements and may look like (Figure A1 below):
For the United States and Canada
In the United States and Canada the male plug is a NEMA5-15 style (Figure A2), UL Listed, and CSA
Labeled. For units which are mounted on a desk or table, type SVT or SJT cord sets may be used. For units
which sit on the floor, only SJT type cord sets may be used. The cord set must be selected according to the
current rating for your unit. Please consult the table below for the selection criteria for power cords used in the
United States and Canada.
For the customer in Canada
Notice: This Class B digital apparatus complies with Canadian ICES-003.
Cord Type
Size of Conductors in Cord
Maximum Current Rating of Unit
SJT
18 AWG
16 AWG
14 AWG
10 Amps
12 Amps
12 Amps
SVT
18 AWG
17 AWG
10 Amps
12 Amps
For European Countries
In Europe you must use a cord set which is appropriate for the receptacles in your country. The cord set is
HAR-Certified, and a special mark that will appear on the outer sheath, or on the insulation of one of the inner
conductors. If you have any questions concerning which proper power cord to use, please consult with the
dealer from whom you have purchased the product.
26
ViewSonic PJ1065
FCC Information
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses, and can radiate radio frequency
energy, and if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC Warning
To assure continued FCC compliance, the user must use grounded power supply cord and the provided
shielded video interface cable with bonded ferrite cores. If a BNC cable is going to be used, use only a
shielded BNC(5) cable. Also, any unauthorized changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate this device.
Instructions to Users
This equipment complies with the requirements of FCC (Federal Communication Commission) equipment provided that
the following condition is met. Use the cables which are included with the projector or specified.
Compliance Information for Canada
Notice: This class B digital apparatus complies with Canadian ICES-003.
AVIS: Cet appeil numerique de la Classe B conforme a la norme NMB-003 du Canada.
Compliance Information for European Countries
CE Conformity
The device complies with the requirements of the EEC directive 89/336/EEC as amended by 92/
31/EEC and 93/68/EEC Art.5 with regard to “Electromagnetic compatibility,” and 73/23/EEC as
amended by 93/68/EEC Art.13 with regard to “Safety.”
User Information for All Countries
NOTICE: Use the cables which are included with the projector or specified.
ViewSonic PJ1065
27
ViewSonic Corporation