Aastra 53I IP PHONE - RELEASE 2.1 User guide

53i IP Phone
User Guide
Release 2.1
41-001199-00
Rev 01
Aastra Telecom does not accept liability for any damages and/or long
distance charges, which result from unauthorized and/or unlawful
use.
While every effort has been made to ensure accuracy, Aastra Telecom is
not liable for technical or editorial errors or omissions
contained within this documentation. The information contained
in this documentation is subject to change without notice.
Copyright 2007 Aastra Telecom. www.aastra.com
All Rights Reserved.
Software License Agreement
Aastra Telecom Inc., hereinafter known as "Seller", grants to Customer a personal,
worldwide, non-transferable, non-sublicenseable and non-exclusive, restricted use
license to use Software in object form solely with the Equipment for which the Software was intended. This Product may integrate programs, licensed to Aastra by third
party Suppliers, for distribution under the terms of this agreement. These programs
are confidential and proprietary, and are protected as such by copyright law as unpublished works and by international treaties to the fullest extent under the applicable
law of the jurisdiction of the Customer. In addition, these confidential and proprietary
programs are works conforming to the requirements of Section 401 of title 17 of the
United States Code. Customer shall not disclose to any third party such confidential
and proprietary programs and information and shall not export licensed Software to
any country except in accordance with United States Export laws and restrictions.
Customer's use of this software shall be deemed to reflect Customer's agreement to
abide by the terms and conditions contained herein. Removal or modification of
trademarks, copyright notices, logos, etc., or the use of Software on any Equipment
other than that for which it is intended, or any other material breach of this Agreement, shall automatically terminate this license. If this Agreement is terminated for
breach, Customer shall immediately discontinue use and destroy or return to Seller
all licensed software and other confidential or proprietary information of Seller. In no
event shall Seller or its suppliers or licensors be liable for any damages whatsoever
(including without limitation, damages for loss of business profits, business interruption, loss of business information, other pecuniary loss, or consequential damages)
arising out of the use of or inability to use the software, even if Seller has been
advised of the possibility of such damages.
Model 53i IP Phone User Guide
iii
Software License Agreement
Customer agrees to not reverse engineer, decompile, disassemble or display Software
furnished in object code form. Customer shall not modify, copy, reproduce, distribute, transcribe, translate or reduce to electronic medium or machine readable form or
language, derive source code without the express written consent of the Seller and its
Suppliers, or disseminate or otherwise disclose the Software to third parties. All Software furnished hereunder (whether or not part of firmware), including all copies
thereof, are and shall remain the property of Seller and its Suppliers and are subject to
the terms and conditions of this agreement. All rights reserved.
Table of Contents
Software License Agreement .................................................................... iii
About This Guide ........................................................................................1
Documentation.............................................................................................1
Introduction .................................................................................................2
Phone Features......................................................................................................... 2
Requirements........................................................................................................... 2
Installation and Setup .............................................................................................. 3
Getting Started.............................................................................................4
Plugging in and Starting the Phone ......................................................................... 4
Idle Screens ............................................................................................................. 6
Incomplete Configuration........................................................................................ 7
No Service ............................................................................................................... 7
Connected State Screens.......................................................................................... 7
IP Phone Keys and Key Descriptions ........................................................8
Key Panel................................................................................................................. 8
Methods for Customizing Your Phone ....................................................11
Phone Options via the IP Phone UI ....................................................................... 11
Phone Options via the Aastra Web UI................................................................... 14
Phone Status...............................................................................................18
Phone Status via IP Phone UI................................................................................ 18
Finding Your Phone’s IP Address ........................................................................ 18
Phone Status via the Aastra Web UI...................................................................... 19
Ring Tones and Tone Sets ..................................................................................... 20
Contrast Level ....................................................................................................... 23
Live Dialpad* ........................................................................................................ 23
Set Audio ............................................................................................................... 24
Time and Date ....................................................................................................... 26
Language ............................................................................................................... 29
User Password ....................................................................................................... 31
Resetting a User Password .................................................................................... 33
Restarting your phone............................................................................................ 34
Phone Lock............................................................................................................ 35
Defining an Emergency Dial Plan ......................................................................... 37
Line Keys and Programmable Keys ........................................................39
Multiple Line and Call Appearance Keys ............................................................. 39
Programmable Keys .............................................................................................. 40
Line Key ................................................................................................................ 42
Speeddial Key........................................................................................................ 43
v
Table of Contents
Customizing Your Phone ..........................................................................20
Table of Contents
Table of Contents
Do Not Disturb (DND) Key .................................................................................. 48
Busy Lamp Field (BLF) Key................................................................................. 49
BLF List Key......................................................................................................... 50
Flash Key............................................................................................................... 52
Automatic Call Distribution (ACD) Key (for Sylantro Servers)........................... 53
Directed Call Pickup/Group Call Pickup Keys (for Sylantro Servers).................. 57
XML Key............................................................................................................... 60
Sprecode Key......................................................................................................... 62
Park/Pickup Keys .................................................................................................. 63
Last Call Return (lcr) Key (for Sylantro Servers).................................................. 66
Directory Key ........................................................................................................ 67
Callers List Key ..................................................................................................... 68
Transfer Key.......................................................................................................... 69
Conference Key ..................................................................................................... 70
Intercom Key ......................................................................................................... 71
None Key............................................................................................................... 73
Phone Lock Key .................................................................................................... 74
Deleting a Key ...................................................................................................... 76
Making Calls..............................................................................................77
Dialing a Number .................................................................................................. 77
Using Handsfree Speakerphone ............................................................................ 78
Using a Headset ..................................................................................................... 79
Redial..................................................................................................................... 80
Mute....................................................................................................................... 81
Receiving Calls...........................................................................................83
Answering an Incoming Call................................................................................. 83
Sending an Incoming Call to Voicemail................................................................ 83
Handling Calls ...........................................................................................84
Placing a Call on Hold........................................................................................... 84
Transferring Calls.................................................................................................. 85
Conferencing Calls ................................................................................................ 87
Ending Calls .......................................................................................................... 93
Managing Calls..........................................................................................94
Directory List......................................................................................................... 94
Callers List........................................................................................................... 104
Call Forwarding................................................................................................... 110
Missed Calls Indicator ......................................................................................... 114
Voicemail ............................................................................................................ 115
Additional Features................................................................................. 116
Star Codes............................................................................................................ 116
Suppress DTMF Playback ................................................................................... 116
Display DTMF Digits.......................................................................................... 117
vi
Table of Contents
Enable/Disable Call Waiting ............................................................................... 118
Play Call Waiting Tone ....................................................................................... 120
Stuttered Dial Tone.............................................................................................. 121
XML Beep Support ............................................................................................. 122
Status Scroll Delay .............................................................................................. 123
Incoming Call Interrupts Dialing......................................................................... 124
Goodbye Key Cancels Incoming Calls................................................................ 125
UPnP Mapping Lines (for remote phones).......................................................... 127
Message Waiting Indicator.................................................................................. 128
Incoming Intercom Call Features ........................................................................ 129
Using Redial Key for “Last Number Redial” ...................................................... 131
Available Features Enabled by Administrators ...................................132
Outgoing Intercom Calls ..................................................................................... 132
Missed Call Summary Subscription .................................................................... 132
Customizable Callers List Key ............................................................................ 133
Autodial (Hotline and Warmline)........................................................................ 133
Centralized Conferencing.................................................................................... 133
Answer and Ignore Softkeys for XML Applications........................................... 134
XML Softkey for Special Characters in XML Applications ............................... 134
“Hold” Feature Enhancement (for Broadsoft Servers)........................................ 134
Model 536M Expansion Module ............................................................135
Using the Expansion Module .............................................................................. 136
Troubleshooting Solutions ......................................................................138
Limited Warranty ...................................................................................143
vii
Table of Contents
Appendix A - Time Zone Codes ............................................................ A-1
About This Guide
This guide explains how to use your new 53i phone. Not all features listed are
available by default. Contact your System Administrator to find out which features
and services are available on your system. Your System Administrator also has the
ability to customize some features on this phone.
Documentation
• Aastra 53i IP Installation Guide – Contains installation and set-up instructions, general features and functions, and basic options list customization.
This Installation Guide is included in the box with your phone.
• Aastra SIP 53i IP Phone User Guide – Describes the most commonly used
features and functions for an end user. This User Guide can be downloaded
from www.aastratelecom.com.
• Aastra SIP 51i, 53i, 55i, 57i, 57i CT IP Phone Administration Guide –
Contains advanced Administrator information and procedures for setting up
the 53i IP Phone on a network. This Administrator Guide is intended for the
System Administrator and can be downloaded from www.aastratelecom.com.
About This Guide
Model 53i IP Phone User Guide
1
Introduction
Introduction
This 53i IP telephone has all the features of a regular business phone, allowing you to
make and receive calls, transfer, conference and more. The 53i IP telephone provides
communications over an IP Network using the SIP IP telephony protocol.
Phone Features
•
•
•
•
•
•
•
3-line LCD screen
6 top keys: 4 are programmable keys
3 call appearance lines with LEDs
Supports up to 9 call lines
Full-duplex speakerphone for handsfree calls
Headset support (modular connector)
Built-in two-port, 10/100 Ethernet switch - lets you share a connection with
your computer
• Inline power support (based on 802.3af standard) which eliminates power
adapters.
• AC power adapter (included)
• Enhanced busy lamp fields*
• Set paging*
*Availability of feature dependant on your phone system or service provider.
Requirements
The 53i IP Phone requires the following environment:
• SIP-based IP PBX system or network installed and running with a SIP
account created for the 53i IP phone.
• Access to a Trivial File Transfer Protocol (TFTP), File Transfer Protocol
(FTP), Hypertext Transfer Protocol (HTTP) server, or HyperText Transfer
Protocol over Secure Sockets Layer (SSL) (HTTPS).
• Ethernet/Fast Ethernet LAN (10/100 Mb)
• Category 5/5e straight through cabling
• Power source
- For Ethernet networks that supply in-line power to the phone (IEEE 802.3af):
- For power, use the Ethernet cable (supplied) to connect from the phone
directly to the network for power. (No 48v AC power adapter required.)
- For Ethernet networks that DO NOT supply power to the phone:
- For power, use the 48V AC Power Adapter (included) to connect from
the DC power port on the phone to a power source.
or
- (optional) - For power, use a Power over Ethernet (PoE) power injector
or a PoE switch. A PoE power injector is available as an optional
accessory from Aastra Telecom. Contact your Administrator for more
information.
2
Model 53i IP Phone User Guide
Installation and Setup
If your System Administrator has not already setup your 53i phone, please refer to
the Aastra 53i Installation Guide for basic installation and physical setup of the 53i.
For more advanced administration and configuration information, System
Administrators should refer to the Aastra SIP 51i, 53i, 55i, 57i, 57i CT IP Phone
Administrators Guide.
Introduction
Model 53i IP Phone User Guide
3
Getting Started
Getting Started
The 53i must be set up and configured prior to its first use. This section describes
phone behavior and start up screens you may see when the phone is first plugged in,
or when it is restarted.
Plugging in and Starting the Phone
The 53i automatically begins the start up sequence as soon as it is connected. The
phone goes through this process the first time you plug in your phone and every time
you restart your phone.
1. The phone displays the following startup screens.
Initializing
network
Aastra 53i
The 53i phone then checks settings and looks for new configuration and firmware
updates for the phone from a server. If a new update is found, the phone displays the
message “Updating Configuration”. This may take a few moments while the phone
downloads the latest updates.
Updating
configuration
Note: New updates to your phone can be automatically scheduled from the
server. This is set up on the phone system by your System Administrator
and should be scheduled during non-business hours or slow call periods.
Important! Do not unplug or remove power to the phone while it is
checking or installing firmware and configuration information.
4
Model 53i IP Phone User Guide
If language packs were loaded to your phone by your System Administrator, the following
screen displays during startup.
Downloading
language packs.....
When the configuration update is complete, the phone displays the following screens.
Network
DSP
SIP
Done
Getting Started
Model 53i IP Phone User Guide
5
Getting Started
Idle Screens
Idle Screen 1
When the phone has successfully updated the configuration and connected to the
network, the phone displays the Idle State screen:
1
John Burns
9054550055
Sat Jun 8 2:55pm
The Idle State screen lists your name (SIP screen name), extension (or phone
number), and day, date, and time. The "1" in the upper corner in the above example
indicates the idle screen for the first line appearance. You can use the left and right
arrow keys to scroll through the idle screens for all three line appearances. The 53i
allows for scrolling up to 3 lines.
This screen is shown whenever your phone is not in use.
Idle Screen 2
The second display line displays the following temporary messages if the event
occurs:
•
•
•
•
•
No Service
DHCP Failed
Restarting......
New IP Obtained
Network Disconnected/Connected
Note: Since the "Network Disconnected/Connected" display on two lines, the
date and time does not show if this event displays.
The second line can also display the following status messages, listed in order of
display priority:
• Call forward status
• DND On (Do Not Disturb)
• Number of missed calls
When more than one status message displays, the
indicate you can use the
messages.
and
1
is shown after the message to
navigation keys to scroll through the remaining
John Burns
CFWD All
Jun 8 2:55pm
2
Network Connected
6
Model 53i IP Phone User Guide
Incomplete Configuration
If your phone displays an "Incomplete Config" message without any extension or
user name at the end of the start up sequence instead of an Idle state screen, this
inidicates the phone configuration that was downloaded from the configuration
server is not complete or correct. Contact your System Administrator for assistance.
No Service
When the phone is not properly connected to the network, or the account has not been
configured by the Network Administrator, the "No Service" or "Network
Disconnected" prompt appears on the display and the telephone status light turns
ON. The phone also displays the default time and date of 12:00am Jan. 1st, 2000.
Check that the cables are tightly connected to the phone and to the wall jack. The
phone should automatically detect when the connection is reconnected and display
the "Network Connected" prompt temporarily.
If changes have been made to your phone settings, you may need to restart your
phone. For more information on restarting your phone, see "Restarting your phone"
on page 34.
For more information about connecting your phone, refer to the Aastra 53i
Installation Guide. Check with your System Administrator for assistance.
Connected State Screens
When the phone has successfully connected to the network, a "happy face" icon
appears to the left of the phone number as show below. This icon in the following
illustration indicates the phone is on-hook.
1
John Burns
9054550055
Sat Jan 1 12:15 p
When the phone is off-hook, the icon displays as follows.
1
Getting Started
John Burns
9054550055
03:00
Note: You can use the left and right arrow keys to display the idle or connected
screens on other lines.
Model 53i IP Phone User Guide
7
IP Phone Keys and Key Descriptions
IP Phone Keys and Key Descriptions
The following sections describe the various 53i phone key functions, and how they
help you make and manage your calls and caller information.
Key Panel
The following table identifies the keys on the key panel of your 53i IP phone that you
can use for handling calls.
Keys
Key Description
Goodbye key - Ends an active call. The Goodbye key also
exits an open list, such as the Options List, without saving
changes.
Options key - Accesses options to customize your phone.
Your System Administrator may have already customized
some of your settings. Check with your System
Administrator before changing the administrator-only
options.
Hold key - Places an active call on hold. To retrieve a held
call, press the call appearance button beside the light that is
flashing.
Redial key - Redials up to 100 previously dialed numbers.
Pressing the Redial key twice simultaneously redials the
last dialed number.
Volume control key - Adjusts the volume for the handset,
headset, ringer, and handsfree speaker.
8
Model 53i IP Phone User Guide
Keys
Key Description
Line/Call Appearance key - Connects you to a line or call.
The Aastra 53i IP phone supports up to 3 line keys.
Mute key - Mutes the microphone so that your caller cannot
hear you (the light indicator flashes when the microphone is
on mute).
Navigation keys - Pressing the UP and DOWN arrow keys
lets you view different status and text messages on the LCD
display (if there is more than 1 line of status/text
messages). These buttons also let you scroll through menu
selections, such as the Options List.
Pressing the LEFT and RIGHT arrow keys lets you view the
different line/call appearances. While in the Options List,
these keys allow you to exit or enter the current option.
When you are editing entries on the display, pressing the
LEFT arrow key erases the character on the left; pressing
the RIGHT arrow key sets the option.
Model 53i IP Phone User Guide
9
IP Phone Keys and Key Descriptions
Handsfree key - Activates Handsfree for making and
receiving calls without lifting the handset. When the audio
mode option is set, this key is used to switch between a
headset and the handsfree speakerphone.
IP Phone Keys and Key Descriptions
Keys
Key Description
Programmable keys - Six Top Keys: 4 are programmable
keys.
Note: Keys 1 and 2 are hardcoded as the SAVE and
DELETE keys, respectively, and cannot be altered.
The following are the default functions for the
programmable keys on the 53i IP phone:
1 - Save
(hardcoded)
Allows you to save numbers
and/or names to the Directory.
Using this key, you enter the
number, name, and line (or
speeddial key) to record in the
Directory List.
2 - Del (Delete)
Allows you to delete entries
(hardcoded)
from the Directory List and Callers
List. (Must enter the Directory or
Callers list and select an entry,
then press twice to delete entry).
3 - Dir (Directory)
Displays up to 200 names and
phone numbers (stored in
alphabetical order)
4 - Callers (Callers List)Accesses the last 200 calls
received.
5 - Xfer (Transfer)
Transfers the active call to another
number
6 - Conf (Conference) Begins a conference call with the
active call.
Note: For more information about programming keys 3, 4,
5, and 6 to perform specific functions, see the
"Programmable Keys" on page 40.
10 Model 53i IP Phone User Guide
Methods for Customizing Your Phone
There are two ways to customize specific options on your phone:
• Using the Options
key on the IP Phone
• Using the Aastra Web UI in an Internet browser window from your PC.
Phone Options via the IP Phone UI
You can customize your phone by pressing the Options
the IP Phone UI.
key and accessing
Option
Number
Methods for Customizing Your Phone
These options allow you to customize the following phone settings.
Option
1
Call Forward
1. Cfwd Number
2. Cfwd Mode
3. No. Rings
2
Preferences
1. Tones
Ring Tone
Tone Set
2. Contrast Level
3. Live Dialpad
4. Set Audio
Audio Mode
Headset Mic Vol
5. Time and Date
Time Zone
Daylight Savings
Time Format
Date Format
Time Server
Time Server 1
Time Server 2
Time Server 3
Set Time
Set Date
6. Language
3
Phone Status
1. IP&MAC Addresses
2. LAN Port
3. PC Port
4. Firmware Info
4
User Password
5
Administrator Menu
(Password Protected)
6
Restart Phone
7
Phone Lock
Note: *The "Administrator Menu" options are administrator level functions
only, and are not accessible by the user. These options should only be set
up and changed by your system administrator.
Model 53i IP Phone User Guide
11
Methods for Customizing Your Phone
Simplified Options Menu
Your System Administrator may configure a simplified options menu for your phone.
The following table indicates the options that may appear on your phone if the
simplified options menu is applied.
Option
Number
Option
1
Call Forward
1. Cfwd Number
2. Cfwd Mode
3. No. Rings
2
Preferences
1. Tones
Ring Tone
Tone Set
2. Contrast Level
3. Live Dialpad
4. Set Audio
Audio Mode
Headset Mic Vol
3
Phone Status
1. IP&MAC Addresses
2. LAN Port
3. PC Port
4. Firmware Info
4
Phone Lock
12 Model 53i IP Phone User Guide
Using the IP Phone UI
IP Phone UI
1. Press the Options key
on the phone to enter the Options List.
2. Use
and
to scroll through the list of options, or press the number corresponding to the Option.
3. Press Enter, the 4 key, or press the digit number of the corresponding option to
select an option.
5. Press the Set or Done key to save the change.
6. Press the
button, the 3 key, or the
out saving changes.
button at any time to exit with-
Reference
For more information about customizing your phone using the available options from
the IP Phone UI, see the section "Customizing Your Phone" on page 20.
For more information about administrator options, contact your System
Administrator.
Model 53i IP Phone User Guide
13
Methods for Customizing Your Phone
4. Change a selected option if applicable.
Methods for Customizing Your Phone
Phone Options via the Aastra Web UI
In addition to the IP Phone UI options, you can customize additional options on the
IP Phone using the Aastra Web UI. In order to access your phone using the Aastra
Web UI, you need to know your phone’s IP address. To find your phone’s IP address,
see "Finding Your Phone’s IP Address" on page 18.
Using the Aastra Web UI
Aastra Web UI
1. Open your web browser, enter the phone’s IP address or host name into the
address field and press <Enter>.
The following logon screen displays.
2. At the prompt, enter your username and password and click
Note: For a user, the default user name is “user” and the password field is left
blank.
14 Model 53i IP Phone User Guide
The Network Status window displays for the IP phone you are accessing..
Methods for Customizing Your Phone
3. You can logout of the Aastra Web UI at any time by clicking Log Off.
Model 53i IP Phone User Guide
15
Methods for Customizing Your Phone
The following categories display in the side menu of the Aastra Web UI: Status,
Operation, Basic Settings.
Headings
Descriptions
Status
The Status section displays the network status and the MAC address
of the IP phone. It also displays hardware and firmware information
about the IP phone. The information in the Network Status window is
read-only.
Operation
User Password - Allows you to change user password.
Phone Lock - Allows you to assign an emergency dial plan to the
phone, lock the phone to prevent any changes to the phone and to
prevent use of the phone, and reset the user password.
Programmable Keys - There are 6 function keys, 4 of which you can
configure to perform the functions identified in the following list.
•
none
•
sprecode
•
line
•
park
•
speeddial
•
pickup
•
do not disturb (DND)
•
Last Call Return (lcr)
•
Busy Lamp Field (BLF)
•
Directory
•
BLF List
•
Callers List
•
Auto Call Distribution
(ACD)
•
Conference
•
Directed Call Pickup
•
Transfer
•
Extensible Markup
Language (XML)
•
Intercom
•
flash
•
Phone Lock
Expansion Module - Allows you to configure an additional 36
softkeys with a 536M Expansion Module if it is attached to the phone.
This option displays on the side menu of the Aastra Web UI only if an
Expansion Module is attached.
Note: Not all functions in the table above apply to the Expansion
Modules.
Directory - Allows you to copy the Callers List and Directory List from
your IP phone to your PC.
Reset - Allows you to restart the IP phone when required.
16 Model 53i IP Phone User Guide
Descriptions
Basic
Settings
Preferences - Allows you to enable/disable the following:
• Suppress DTMF Playback
• Display DTMF Digits
• Call Waiting
• Play Call Waiting Tone
• Stuttered Dial Tone
• XML Beep Support
• Status Scroll Delay
• Incoming Call Interrupts Dialing
• Goodbye Key Cancels Incoming Call
• UPnP Mapping Lines
• Message Waiting Indicator Line
This category also allows you to configure:
• incoming Intercom call settings
• ring tones (global and per-line basis)
• ring tone sets
• time and date settings
• language settings.
Call Forward - Allows you to set a phone number destination for
where you want calls forwarded. Call forward can be configured using
a specific mode (off, all, busy, no answer, busy no answer) on a global
or per-line basis.
Model 53i IP Phone User Guide
17
Methods for Customizing Your Phone
Headings
Phone Status
Phone Status
You can view the status of your phone using the IP Phone UI or the Aastra Web UI.
Phone Status via IP Phone UI
The "Phone Status" option on the IP phone displays the status of your phone to the
LCD display.
This option allows you to view your phone’s:
• Network status including your phone’s IP and MAC address
• Local Area Network (LAN) port
• PC port
• Firmware version
Use the following procedure to view the status of your phone using the IP Phone UI.
IP Phone UI
1. Press
on the phone to enter the Options List.
2. Select Phone Status.
3. Select the option you want to view:
IP&MAC Address
LAN Port
PC Port
Firmware Info
The option you select displays to the LCD. Use the
through the LCD display.
and
keys to scroll the
Finding Your Phone’s IP Address
If you want to access your phone’s options using an Internet browser, you need to
enter the IP address of the phone in the browser to open the Aastra Web UI. Use the
following procedure to find your phone’s IP address.
IP Phone UI
1. Press the
button on the phone to enter the Option List.
2. Select Phone Status and press the 4 key.
3 Phone Status
=Next
18 Model 53i IP Phone User Guide
=Enter
3. Select "IP&MAC Addresses" and press the 4 key.
1 IP&MAC Addresses
=Next
=Enter
The IP address of your 53i IP phone displays in the "IP Address" field.
IP Address:
10.40.50.112
=Next
=Exit
Phone Status via the Aastra Web UI
After accessing your phone via the Aastra Web UI, the first screen to display is the
phone’s Status Screen.
This screen is view only. It displays the Network Status of your phone which includes
the following:
LAN Port
PC Port
MAC Address
Hardware Information
Firmware Information
Phone Status
•
•
•
•
•
Model 53i IP Phone User Guide
19
Customizing Your Phone
Customizing Your Phone
The following paragraphs describe the options available from either the IP Phone UI,
the Aastra Web UI, or both, and provide procedures applicable to the option.
Ring Tones and Tone Sets
You can configure ring tones and ring tone sets on the IP phone.
Ring Tones
There are several distinct ring tones a user can select from to set on the IP phones.
You can enable/disable these ring tones on a global or per-line basis.
The following table identifies the valid settings and default values for each type of
configuration method.
Ring Tones Table
Configuration Method
Valid Values
Default Value
IP Phone UI
Global:
Tone 1
Tone 2
Tone 3
Tone 4
Global:
Tone 1
Aastra Web UI
Global:
Tone 1
Tone 2
Tone 3
Tone 4
Tone 5
Silent
Global:
Tone 1
Per-Line:
Global
Tone 1
Tone 2
Tone 3
Tone 4
Tone 5
Silent
Per-Line:
Global
20 Model 53i IP Phone User Guide
Ring Tone Sets
In addition to ring tones, you can configure ring tone sets on a global-basis on the IP
phone. Ring tone sets consist of tones customized for a specific country. The ring
tone sets you can configure on the IP phones are:
• US (Default - also used in Canada)
• Mexico
• United Kingdom
• Italy
• Germany
• France
• Europe (generic tones)
• Australia
When you configure the country's tone set, the country-specific tone is heard on the
phone for the following:
dial tone
secondary dial tone
ring tone
busy tone
congestion tones
call waiting tone
ring cadence pattern
Configuring Ring Tones and Tone Sets
IP Phone UI
Use the following procedures to configure ring tones and tone sets on the IP phone.
(global configuration only)
1. Press
on the phone to enter the Options List.
2. Select Preferences.
3. Select Tones.
4. Select Ring Tone.
5. Select the type of ring tone (Tone 1 through Tone 5, or Silent).
6. Select Set and then press
.
7. Select Tone Set.
8. Select the country for which you want to apply the tone set. Valid values are Australia, Europe, France, Germany, Italy, UK, Mexico, and US. Default is US.
9. Press 4.
The ring tone and tone set you select is immediately applied to the IP phone.
Model 53i IP Phone User Guide
21
Customizing Your Phone
You configure global ring tones and tone sets using the Aastra Web UI and the IP
Phone UI.
Customizing Your Phone
Aastra Web UI
1. Click on Basic Settings->Preferences->Ring Tones.
For global configuration:
2. In the "Ring Tones" section, select a country from the "Tone Set" field.
Valid values are Australia, Europe, France, Germany, Italy, UK, Mexico, and
US. Default is US.
3. Select a value from the "Global Ring Tone" field.
Note: *See the Ring Tones Table on page 20 for valid values.
For per-line configuration:
4. In the "Ring Tone" section, select a line for which you want to set ring tone.
5. Select a value from the "LineN" field.
Note: See the Ring Tones Table on page 20 for valid values.
6. Click
to save your changes.
22 Model 53i IP Phone User Guide
Contrast Level
The "Contrast Level" option on the IP phone allows you to set the amount of light
that illuminates the LCD display. Use this option to set the preference of contrast
level.
You can set the contrast level using the IP Phone UI only.
Setting Contrast Level
IP Phone UI
1. Press
on the phone to enter the Options List.
2. Select Preferences.
3. Select Contrast Level.
4. Use the 3 and 4 nagivation buttons to increase or decrease the intensity of contrast lighting on the LCD.
5. Press Set to save your selection.
Live Dialpad*
the
initiates a call to that number.
*Availability of feature dependant on your phone system or service provider.
You can enable/disable the live dialpad using the IP Phone UI only.
Enabling/Disabling Live Dialpad
IP Phone UI
1. Press
on the phone to enter the Options List.
2. Select Preferences.
3. Select Live Dialpad.
4. Use the Change softkey to turn the live dialpad ON or OFF.
5. Press Done to save your selection.
Model 53i IP Phone User Guide
23
Customizing Your Phone
The "Live Dialpad" option on the IP phone turns the Live Dial Pad mode ON or
OFF. With live dial pad ON, the 53i IP phone automatically dials out and turns ON
Handsfree mode as soon as a dial pad key or softkey is pressed. With live dial pad
OFF, if you dial a number while the phone is on-hook, lifting the receiver or pressing
Customizing Your Phone
Set Audio
The "Set Audio" option on the IP Phone allows you to set the audio mode for your IP
phone. It also allows you to set the volume level of the headset microphone.
You can set Audio on your IP phone using the IP Phone UI only.
Audio Mode
The 53i allows you to use a handset, a headset, or handsfree mode to handle incoming
and outgoing calls. The audio mode option provides different combinations of these
three methods to provide maximum flexibility in handling calls. There are four audio
mode options you can set:
Audio Mode Option Description
Speaker
This is the default setting. Calls can be made or received
using the handset or handsfree speakerphone. In handset
audio mode, pressing the
button on the phone
switches to handsfree speakerphone. In Speaker audio
mode, lift the handset to switch to the handset.
Headset
Choose this setting if you want to make or receive all calls
using a handset or headset. Calls can be switched from the
handset to headset by pressing the
button on the
phone. To switch from the headset to the handset, lift the
handset.
Speaker/Headset
Incoming calls are sent to the handsfree speakerphone first
when the
button is pressed. By pressing the button
again, you can switch back and forth between the
handsfree speakerphone and the headset. At anytime,
lifting the handset switches back to the handset from either
the handsfree speakerphone or the headset.
Headset/Speaker
Incoming calls are sent to the headset first when the
button is pressed. By pressing the button again,
you can switch back and forth between the headset and the
handsfree speakerphone. At anytime, lifting the handset
switches back to the handset from either the headset or the
handsfree speakerphone.
24 Model 53i IP Phone User Guide
Headset Mic Volume
The "Headset Mic Volume" option allows you to set the volume level for the headset
microphone.
Setting Audio Mode and Headset Mic Volume
IP Phone UI
1. Press
on the phone to enter the Options List.
2. Select Preferences.
3. Select Set Audio.
4. Select Audio Mode.
5. Select the audio mode you want to use on your phone. Valid values are:
Speaker
Headset
Speaker/Headset
Headset/Speaker
6. Press Done to save your selection.
7. Select Headset Mic Volume.
8. Select the Low, Medium, or High volume level.
Customizing Your Phone
9. Press Done to save your selection.
Model 53i IP Phone User Guide
25
Customizing Your Phone
Time and Date
On the IP phones, you can configure the following:
•
•
•
•
Time and date
Time and date format
Time zone
Daylight savings time
• Time Servers (Administrator use only;password protected)
Note: You can set the above features using the IP Phone UI. However, only the
Time and Date Formats can be set using the Aastra Web UI. The "Time
Server" configuration is for Administrator use only and is password protected. Contact your System Administrator for more information.
Configuring Time and Date
Use the following procedures to configure the time and date settings on the IP phone.
IP Phone UI
Set Time and Time Format
1. Press
2.
3.
4.
5.
6.
7.
8.
9.
on the phone to enter the Options List.
Select Preferences.
Select Time and Date.
Select Set Time.
Using the keys on the keypad, enter a time to set on the IP phone. Use the
3 and 4 navigation keys to move backward or forward when entering the time.
Use the "*" key to set either AM or PM.
Press Set to save the time setting.
Select Time Format.
Using the "Change" softkey, set the Time Format to either a 12 hour format or a
24 hour format. Valid values are 12h and 24h. Default is 12h.
Press Set to save the Time Format you selected.
Set Date and Date Format
1. Select Preferences.
2. Select Time and Date.
3. Select Set Date.
4. Using the keys on the keypad, enter a date to set on the IP phone. Use the
3 and 4 navigation keys to move backward or forward when entering the date.
5. Press Set to save the date setting.
6. Select Date Format.
26 Model 53i IP Phone User Guide
7. Select a date format from the list of options. Default is Sun Jan 2. Valid values
are:
•
•
•
•
•
•
•
•
•
•
•
Sun Jan 2 (Default)
2-Jan-00
2000 01 02
02/01/2000
02/01/00
02-01-00
01/.02/00
Jan 2
2 Jan 2000
Sun 2 Jan
2 Jan
• 02.01.2000
8. Press Set to save the Date Format setting.
Set Time Zone
1. Select Preferences.
2. Select Time and Date.
3. Select Time Zone.
Customizing Your Phone
4. Press * to display a list of Time Zone options.
A list of Time Zones display for different areas of the world.
5. Select a Time Zone that applies to your area.
The default Time Zone is US-Eastern.
Note: For a list of the Time Zones values available on the IP Phone, see
“Appendix A - Time Zone Codes.”.
6. Press Set to save the Time Zone setting.
Set Daylight Savings Time
1. Select Preferences.
2. Select Time and Date.
3. Select Daylight Savings.
4. Select a Daylight Savings time from the list of options.
Valid values are:
•
•
•
OFF
30 min summertime
1 h summertime
•
Automatic
Note: The default for Daylight Savings is Automatic.
5. Press Set to save the Daylight Savings setting.
Model 53i IP Phone User Guide
27
Customizing Your Phone
Aastra Web UI
1. Click on Basic Settings->Preferences->Time and Date Setting.
2. In the “Time Format” field, select the time format you want to use on your
phone. Valid values are:
12h (12 hour format) (default)
24h (24 hour format)
Note: The time and time format you configure display on the phone’s idle
screen.
3. In the “Date Format” field, select the date format you want to use on your phone.
Default is WWW MMM DD. Valid values are:
•
•
•
•
•
•
•
•
•
•
•
WWW MMM DD (default)
DD-MMM-YY
YYYY-MM-DD
DD/MM/YYYY
DD/MM/YY
DD-MM-YY
MM/DD/YY
MMM DD
DD MMM YYYY
WWW DD MMM
DD MMM
• DD.MM.YYYY
Note: The date and date format you configure display on the phone’s idle
screen.
4. Click
to save your changes.
28 Model 53i IP Phone User Guide
Language
The IP phones support several different languages. You can have the IP Phone UI and
the Aastra Web UI display in a specific language as required. When you set the
language to use, all of the display screens (menus, services, options, configuration
parameters, etc.) display in that language. The IP phones support the following
languages:
•
•
•
•
•
English (default)
French
Spanish
German
Italian
Specifying the Language to Use
Once the language pack(s) are available on your phone from your System
Administrator, you can specify which language to use on the phone and/or the Aastra
Web UI.
Note: All languages may not be available for selection. The available languages are dependant on the language packs currently loaded to the IP
phone.
Use the following procedure to specify which language to use for the IP Phone UI.
1. Press
on the phone to enter the Options List.
2. Select Language and press Enter..
The language setting displays a check mark indicating this is the current language
on the IP Phone.
3. Using the
and
keys, scroll through the languages. Valid values are:
English (English), Français (French), Español (Spanish), Deutsch (German), or
Italiano (Italian). Default is English.
Note: All languages may not be available for selection. The available languages are dependant on the language packs currently loaded to the IP
phone. English is the default language and cannot be changed or
removed. For more information about loading language packs, see your
System Administrator.
4. Press Set to set the language on the phone.
The change is dynamic. When you exit the Options Menu, the phone displays all
menu items in the language you selected.
Model 53i IP Phone User Guide
29
Customizing Your Phone
IP Phone UI
Customizing Your Phone
Aastra Web UI
Note: You must have the language pack(s) already loaded to your phone in
order to use them. For more information about loading language packs,
see your System Administrator.
1. Click on Basic Settings->Preferences->Language Settings.
2. In the “Webpage Language” field, select a language to apply to the Aastra Web
UI. The IP phone supports the following languages:
English (default)
French
Spanish
German
Italian
Note: All languages may not be available for selection. The available languages are dependant on the language packs currently loaded to the IP
phone by your System Administrator. English is the default language
and cannot be changed or removed.
3. Click
to save your settings. The change is dynamic. The Aastra Web UI
displays all screens in the language you selected.
30 Model 53i IP Phone User Guide
User Password
This category allows you to change the user password for your phone. Changing your
password ensures that only you can alter your phone settings, and helps keep your
system secure. You can change your user password using the IP Phone UI or the
Aastra Web UI.
If you change the password
Then you need to:
using the IP Phone UI,
use that new password to log into the
Aastra Web UI.
using the Aastra Web UI,
use that new password when changing
the user password via the IP Phone UI.
Note: Valid values when creating or changing a password are 0 to 4294967295
(integers only; symbols and alpha characters are not allowed). Default
password is an empty string "" (field is blank).
Setting a User Password
IP Phone UI
on the phone to enter the Options List.
Customizing Your Phone
1. Press
2. Select User Password and press Enter.
3. At the "Current Password" prompt, enter the current user password and press
Enter..
4. At the "New Password" prompt, enter the new user password and press Enter.
5. At the "Enter Again" promot, re-enter the new user password and press Enter.
A message, "Password Changed" displays on the screen.
Model 53i IP Phone User Guide
31
Customizing Your Phone
Aastra Web UI
1. Click on Operation->User Password.
2. In the "Current Password" field, enter the current user password.
Note: By default, the user name is “user” (all lowercase) and the password
field is left blank.
3. In the "New Password" field, enter the new user password.
4. In the "Password Confirm" field, enter the new user password again.
5. Click
to save your changes.
32 Model 53i IP Phone User Guide
Resetting a User Password
If you forget your password, you can reset it and enter a new password. The reset user
password feature resets the password to the factory default which is blank (no
password).
You can reset a user password using the Aastra Web UI only.
Note: Valid values when creating or changing a password are 0 to 4294967295
(integers only; symbols and alpha characters are not allowed). Default
password is an empty string "" (field is blank).
Reset a User Password
Use the following procedure to reset a user password.
Aastra Web UI
1. Click on Operation->Phone Lock.
Customizing Your Phone
.
2. In the "Reset User Password" field, click
The following screen displays.
3. In the "Current Password" field, leave this blank.
4. In the "New Password" field, enter a new password.
5. In the "Password Confirm" field, re-enter your new user password.
6. Click
to save your settings.
Model 53i IP Phone User Guide
33
Customizing Your Phone
Restarting your phone
You may want to restart your phone to check for updates for your phone on the
server. You may occasionally need to restart your phone to set changes or updates to
your phone or network settings. You may also need to restart your phone if you have
been asked to do so by your System Administrator, or should you experience any
unexpected behavior.
IP Phone UI
1. Press the
button on the phone to enter the Options List.
2. Select Restart Phone.
3. Press # to confirm the restart of the phone. If you do not wish to restart your
phone, press the 3 key to cancel.
Note: Your phone is out of service temporarily during the restart and downloading process.
Aastra Web UI
1. Click on Operation->Reset.
2. Click
.
3. Click OK at the confirmation prompt.
34 Model 53i IP Phone User Guide
Phone Lock
You can lock your phone to prevent the phone from being used or configured. You
can lock the phone using any of the following:
• At the path Options->Phone Lock on the IP Phone UI.
• At the path Operations->Phone Lock on the Aastra Web UI.
• At a configured key on the phone. For more information about configuring a
Lock/Unlock key on your phone, see "Phone Lock Key" on page 74.
In the Aastra Web UI, the Operation->Phone Lock path also allows you to perform
the following:
• Reset a user password. Clicking on the “Reset” button in the “Reset User
Password” field displays a screen that allows you to enter and save a new user
password.
• Set an emergency dial plan. An emergency dial plan can be 911, 999, 112, 110
or all of the above. The default emergency dial plan is 911|999|112|110.
The following procedures describe locking the phone, setting an emergency dial plan,
and resetting the user password.
Locking/Unlocking a Phone
Use the following procedures to lock an IP phone and prevent it from being used or
configured.
Customizing Your Phone
IP Phone UI
Lock the Phone
1. Press
on the phone to enter the Options List.
2. Select Phone Lock and press Enter.
3. At the "Lock the phone?" prompt, press Lock.
The message "Phone is locked" displays.
.
Unlock the Phone
1. Press
on the phone to enter the Options List.
2. At the prompt, "Password:", enter your user password and press Enter..
The phone unlocks.
Model 53i IP Phone User Guide
35
Customizing Your Phone
Aastra Web UI
1. Click on Operation->Phone Lock.
Lock the Phone
2. In the "Lock the Phone?" field, click
.
The phone locks dynamically and displays the following message:
"Phone is locked".
Unlock the Phone
3. Click on Operation->Phone Lock.
4. In the "Unlock the Phone?" field, click
.
The phone unlocks dynamically and displays the following message:
"Phone is unlocked".
36 Model 53i IP Phone User Guide
Defining an Emergency Dial Plan
Public telephone networks in countries around the world have a single emergency
telephone number (emergency services number), that allows a caller to contact local
emergency services for assistance when required. The emergency telephone number
may differ from country to country. It is typically a three-digit number so that it can
be easily remembered and dialed quickly. Some countries have a different emergency
number for each of the different emergency services.
You can specify the digits to dial on the IP phone for contacting emergency services.
Once you specify the emergency number(s) on the phone, you can dial those numbers
directly on the dial pad when required and the phone automatically dials to those
emergency services.
Note: Contact your local phone service provider for available emergency numbers in your area.
The following table describes the default emergency numbers on the IP phones.
Description
911
A United States emergency number
999
A United Kingdom emergency number
112
An international emergency telephone number for GSM mobile
phone networks.
In all European Union countries it is also the emergency
telephone number for both mobile and fixed-line telephones.
110
A police and/or fire emergency number in Asia, Europe, Middle
East, and South America.
Customizing Your Phone
Emergency
Number
You can set the emergency dial plan using the Aastra Web UI.
Model 53i IP Phone User Guide
37
Customizing Your Phone
Define an Emergency Dial Plan
Use the following procedure to specify the numbers to use on your phone for dialing
emergency services in your area.
Aastra Web UI
1. Click on Operation->Phone Lock.
2. In the "Emergency Dial Plan" field, enter the 3-digit number used in your local
area to contact emergency services. For multiple numbers, enter a “|” between
each emergency number. For example:
911|110
Default for this field is 911|999|112|110.
3. Click
to save the emergency dial plan to your phone.
Reference
For more advanced options you can set on your phone, see "Additional Features" on
page 116.
38 Model 53i IP Phone User Guide
Line Keys and Programmable Keys
This section describes the Multiple Line/Call Appearance Keys (L1, L2, and L3) and
the customizable programmable keys located at the top left on the phone.
Programmable Keys
Multiple Line and Call Appearance Keys
The 53i has 3 hard line/call appearance keys each with a corresponding status light.
These line/call appearance buttons and lights can represent physical lines, calls for
your extension or calls from a group that your extension is part of. By pressing a line/
call appearance button, you connect to the line or a call it represents. The line/call
appearance light indicates the status of that line or call. When the phone is taken offhook, the phone automatically selects a line for you.
Line/Call Appearance
Light Behavior
Line/Call
Appearance Status
Off
Idle line or no call
activity
Light flashes quickly
Ringing
Light is solid
Connected
Light flashes slowly
Hold
When you have more than one call, you can use the left and right navigation buttons
(3 and 4) to scroll left and right to the different call information. Icons 3 and 4
appear if there is call information either left, right or both sides of the current
information you are viewing.
The display shows which line the call information is referring to (L1, L2, L3, etc.),
the Caller ID information (name and number, if available), the call status
(Connected, Ring, Hold, etc.) and the timer specific to that call.
Model 53i IP Phone User Guide
39
Line Keys and Programmable Keys
Multiple Line/
Call Appearance
Keys
Line Keys and Programmable Keys
Programmable Keys
There are six function keys on the 53i phone, 4 of which are programmable, located
to the left of the paper label.
Save Key
Delete Key
Directory
Callers List
Transfer
Conference
Programmable
Keys
Note: If a 536M Expansion Module(s) are attached to the phone, you can configure 36 additional keys on each Expansion Module (Phone allows up
to 3 expansion modules totaling up to 108 additional softkeys). For more
information about expansion modules, see "Model 536M Expansion
Module" on page 135.
You can use the Aastra Web UI only, to configure key functions. The following table
lists the functions you can set on the programmable keys and provides a description
for each function.
Key Function
Description
None
Indicates no setting for the key.
Line
Indicates the key is configured for line use.
Speeddial
Indicates the key is configured for speeddial use. You can
also configure a prefix for a speeddial number.
Do Not Disturb
Indicates the key is configured for "do not disturb" on the
phone.
Busy Lamp Field
(BLF)
Indicates the key is configured for Busy Lamp Field (BLF)
use. User can dial out on a BLF configured key.
(Maximum of 50 BLFs allowed on 536M Expansion
Module.)
BLF List
Indicates the key is configured for BLF list use. User can
dial out on a BLF List configured key.
Auto Call
Distribution (ACD)
(For Sylantro Servers)
Indicates the key is configured to allow the Sylantro
server to distribute calls from a queue to registered IP
phone users (agents).
Directed Call
Pickup (DCP)/
Group Call Pickup
(GCP)
(For Sylantro Servers)
Indicates the key is configured to allow you to intercept or pickup - a call on a monitored extension(s).
40 Model 53i IP Phone User Guide
Key Function
Description
Indicates the key is configured to accept an XML
application for accessing customized XML services. You
can also specify an XML key URL for this option.
Flash
Indicates the key is set to generate a flash event when it
is pressed on the 53i. The IP phone generates flash
events only when a call is connected and there is an
active RTP stream (for example, when the call is not on
hold).
Sprecode
Indicates the key is configured to automatically activate
specific services offered by the server. For example, if the
sprecode value of *82 is configured, then by pressing the
Sprecode key, *82 automatically activates a service
provided by the server. Contact your System
Administrator for available services.
Park
Indicates the key is configured to park incoming calls
when pressed.
Pickup
Indicates the key is configured to pick up parked calls
when pressed.
Last Call Return
(lcr)
Indicates the key is configured for “last call return” when
pressed.
Directory
(Key 3 by Default)
Indicates the key is configured to access the Directory
List.
Callers List
(Key 4 by Default)
Indicates the key is configured to access the Callers List.
Transfer
(Key 5 by Default)
Indicates the key is configured as a Transfer key (Xfer)
for transferring calls.
Conference
(Key 6 by Default)
Indicates the key is configured as a Conference key
(Conf).
Intercom
Indicates the the key is configured to be used for intercom
calls.
Phone Lock
Indicates the key is configured as a phone lock key,
allowing you to press this key to lock/unlock the phone.
Line Keys and Programmable Keys
XML
Programmable keys can also be set up to quickly to access features such as Call
Return (*69) or Voicemail.
Note: Quick access features like Call Return and Voicemail must first be configured on your PBX in order to work on your phone. See your System Administrator for more information.
Model 53i IP Phone User Guide
41
Line Keys and Programmable Keys
Line Key
You can set a programmable key to act as a line/call appearance key on the 53i. The
programmable key acts as a line that behaves the same as a hard line key (L1, L2, and
L3) . For more information about the behavior of line keys, see "Multiple Line and
Call Appearance Keys" on page 39.
You use the Aastra Web UI to set a programmable key as a line.
Configuring a Line Key
Aastra Web UI
Use the following procedure to set a programmable key to function as a line.
1. Click on Operation->Programmable Keys.
or
Click on Operation->Expansion Module <N>.
2. Select from "Key 3" through "Key 6".
3. In the "Hard Key" field, select Line to apply to the programmable key.
4. In the "Line" field, select a line for which to apply this programmable hard key.
Valid values are 4 through 9.
5. Click
to save your changes.
42 Model 53i IP Phone User Guide
Speeddial Key
The normal function of the speeddial option allows you to dial a number quickly by
pressing a programmable key configured for speeddialing. You can program the keys
on the 53i to speeddial outside numbers, dial directly to another person’s line or
extension, or set up to quickly access features such as Caller ID (*69), Voicemail.
The speeddial function can be set using the IP Phone UI or the Aastra Web UI.
Note: You can use a speeddial key while on an active call by placing the active
call on hold first, and then pressing the speeddial key.
Speeddial Prefix
For example, if you had the following speeddial configuration in the Aastra Web UI:
Key 1
Type=speeddial
Label=Europe Office
Value=1234567+
Line=2
then, after you press key 1 on the phone, the prefix number displays on the phone
screen. The phone proceeds to dial the prefix number automatically and pauses for
you to enter the remaining phone number using the keypad on the phone.
You can save up to 7 speeddial numbers on the 53i.
Use the following procedures to set speeddial on the 53i IP phone.
Creating a Speeddial Key Using the Programmable Keys
IP Phone UI
Pressing and holding down a programmable key on the phone initiates a speeddial
feature.
Note: When creating a speeddial key from the IP Phone UI, you must select a
programmable key that has no preassigned function (key must be set to
None.
1. Press a programmable key or a number key on the keypad for 3 seconds.
A screen displays with the prompt, "Enter number>".
2. Enter a phone number or extension to assign to that speeddial key.
The following example illustrates the screen display:
Speeddial
Enter number> 3456
Model 53i IP Phone User Guide
43
Line Keys and Programmable Keys
The speeddial feature also allows you to specify a preset string of numbers followed
by a “+” that the phone dials automatically after pressing the speeddial key. You can
use this feature for numbers that contain long prefixes.
Line Keys and Programmable Keys
After entering the number, the prompt, "Use Save to end" displays on the screen.
3456
Use Save to end
3. Press Save to save the number as a speeddial key.
By default, the phone automatically assigns the speeddial key to line 1 if available. To select a different line, press the Change softkey and select a different
line, or use the phone’s keypad to select a number (1-9), or use the
and
to
make your selection.
Line: 1
Change
Use Save to end
4. Press Save to save the speeddial key to the line specified.
Note: Use the Aastra Web UI to edit or delete this speeddial key.
Creating a Speeddial Key Using the Save Key
IP Phone UI
Use the following procedure to create a speeddial key using the Save key. Use the
following illustration for reference.
Save Key
Programmable
Keys
44 Model 53i IP Phone User Guide
1. Press the Save key. The screen displays "Save to?"
Save to?
2. Select a Programmable key you want to save to.
3. At the "Enter Number" prompt, use the dial pad key to enter the number.
Enter Number >
5553491234
5. At the "Enter Name" prompt, use the dial pad keys to select the letters. Continue
to press the number key to access the next letter for that key (i.e. press 2 three
times to access C). Press 4 to move to the next space, or wait a moment and the
cursor automatically advances. To insert a space between letters, press 4. To
backspace and erase a mistake, press 3 or the Delete key. You can save up to 16
letters and numbers on each programmable key entry.
Enter Name >
John Smith
6. Press the Save key to finish.
Saved Memory key
5553491234
Model 53i IP Phone User Guide
45
Line Keys and Programmable Keys
4. Press the Save key to save the speeddial configuration.
Line Keys and Programmable Keys
Creating a Speeddial Key Using the Aastra Web UI
Aastra Web UI
1. Click on Operation->Programmable Keys.
or
Click on Operation->Expansion Module <N>.
2. Select from "Key 3" through "Key 6".
3. In the "Hard Key" field, select Speeddial to apply to the programmable key.
4. In the "Value" field, enter the phone number, extension, or speeddial prefix to
apply to this hard key. If you enter a speeddial prefix, you must enter the "+" character at the end of the prefix number (for example, "123456+").
5. In the "Line" field, select a line for which to apply the speeddial to. Valid values
are 1 through 9.
6. Click
to save your changes.
46 Model 53i IP Phone User Guide
Saving an Entry from the Redial, Callers, or Directory Lists to a
Speeddial Key
IP Phone UI
Use the following procedure to save an entry from your Directory List, Callers List,
or Redial List on the IP phone.
Save Key
Directory List Key
Callers List Key
1. Press the Directory List, Callers List, or Redial List key. From the Directory
List, Callers List, or Redial List, scroll through the list to find the name and number that you wish to save to your speeddial.
2. Press the Save key.
3. Press the selected speed dial. If the name is displayed with the number, both are
saved to the speed dial. If no name is displayed, you can enter the name using the
phone’s key pad.
Model 53i IP Phone User Guide
47
Line Keys and Programmable Keys
Redial List Key
Line Keys and Programmable Keys
Do Not Disturb (DND) Key
The IP phones have a feature you can enable called "Do not Disturb (DND). The
DND function allows you to turn "do not disturb" ON and OFF.
Note: You can configure DND using the Aastra Web UI only.
If DND is ON, callers calling into the phone hear a busy signal or a message,
depending on how your System Administrator set up the configuration server. The
second line on the screen of the IP phone shows when DND is set.
If the phone shares a line with other phones, only the phone that has DND configured
is affected.
You can set DND on the programmable keys using the Aastra Web UI only. DND is
not configurable from the IP phone UI.
Configuring a DND Key
Aastra Web UI
1. Click on Operation->Programmable Keys.
or
Click on Operation->Expansion Module <N>.
2. Select a "Key 3" through "Key 6".
3. In the "Hard Key" field, select do not disturb to apply to the programmable key.
4. Click
to save your changes.
48 Model 53i IP Phone User Guide
Busy Lamp Field (BLF) Key
The BLF feature on the IP phones allows a specific extension to be monitored for
state changes. BLF monitors the status (busy or idle) of extensions on the IP phone.
Note: The BLF setting is applicable to the Asterisk server only.
Example
A Supervisor configures BLFs on his phone for monitoring the status of a worker’s
phone use (busy or idle). When the worker picks up his phone to make a call, a busy
indicator on the Supervisor’s phone shows that the worker’s phone is in use and busy.
You can set BLF on the programmable keys using the Aastra Web UI only. BLF is not
configurable from the IP phone UI.
Note: You can also use a BLF configured key to dial out. Contact your System
Administrator for more information
Configuring a BLF Key
Aastra Web UI
1. Click on Operation->Programmable Keys.
or
Click on Operation->Expansion Module <N>.
2. Select a "Key 3" through "Key 6".
3. In the "Hard Key" field, select BLF to apply to the programmable key.
4. In the "Value" field, enter the phone number or extension you want to monitor.
5. In the "Line" field, select a line for which to apply this programmed key. Valid
values are Global (for all lines), or 1 through 9.
6. Click
to save your changes.
Model 53i IP Phone User Guide
49
Line Keys and Programmable Keys
On the 53i, the busy and idle indicators are the LEDs next to each BLF
programmable key. The LED illuminates steady to indicate the monitored line is offhook or unregistered. The LED goes off when the line is idle.
Line Keys and Programmable Keys
BLF List Key
(For use with the BroadSoft Broadworks Rel 13 or higher platform only)
The BLF\List feature on the IP phones is specifically designed to support the
BroadSoft Broadworks Rel 13 Busy Lamp Field feature.
This feature allows the IP phone to subscribe to a list of monitored users defined
through the BroadWorks web portal.
Note: Your System Administrator must have BLF List enabled on the BroadWorks Server. Contact your System Administrator for more information.
In addition to monitoring the idle and busy state, the BLF\List feature also supports
the ringing state. On the 53i phone, the LED lights next to each BLF programmable
key illuminate steady to indicate the monitored line is off-hook or unregistered. The
LED goes off when the is idle. When the monitored extension is ringing, the LED
flashes.
Note: You can use a BLF\List configured key to dial out.
Example
A receptionist has a 53i running Broadsoft firmware that subscribes to a list of
extensions from the BroadWorks Application Server. On the 53i running Broadsoft
firmware, the programmable key LEDs illuminate either flashing, solid, or turn off
depending on the state of those extensions.
Note: The Broadworks BLF feature is not the same as the Broadworks Shared
Call Appearance (SCA) feature and does not permit call control over the
monitored extension.
50 Model 53i IP Phone User Guide
Configuring a BLF List Key
Aastra Web UI
The BLF List function can be configured on the 53i using the Aastra Web UI only.
If you set a key to use BLF/List, you must also enter a BLF List URI at Operation>Programmable Keys->Services. The BLF List URI is the name of the BLF list
defined on the BroadSoft BroadWorks Busy Lamp field page for your particular user.
For example, my480i-blf-list@as.broadworks.com. The value of the BLF\List URI
parameter must match the list name configured. Otherwise, no values display on the
53i screen and the feature is disabled.
2. Select a "Key 3" through "Key 6".
3. In the "Hard Key" field, select "BLF\List" (BroadSoft BroadWorks).
Note: The "Label" and "Value" field are not required. The BroadWorks BLF
List name is configured in the "BLF List URI" field instead.
4. In the "Line" field, select a line number that is actively registered to the appropriate SIP proxy you are using. Valid values are Global (for all lines), or 1 through 9.
5. In the "BLF List URI" field, enter the name of the BLF list defined on the BroadSoft BroadWorks Busy Lamp field page for your particular user. For example,
my53i-blf-list@as.broadworks.com.
Note: Contact your System Administrator for the BLF List URI.
6. Click
to save your changes.
Model 53i IP Phone User Guide
51
Line Keys and Programmable Keys
1. Click on Operation->Programmable Keys.
or
Click on Operation->Expansion Module <N>.
Line Keys and Programmable Keys
Flash Key
You can set a programmable key to generate a flash event when it is pressed on the
53i. You do this by setting the programmable key to "flash". The IP phone generates
flash events only when a call is connected and there is an active RTP stream (for
example, when the call is not on hold).
Configuring a Flash Key
Aastra Web UI
1. Click on Operation->Programmable Keys.
2. Select a "Key 3" through "Key 6".
3. In the "Hard Key" field, select flash.
4. Click
to save your changes.
52 Model 53i IP Phone User Guide
Automatic Call Distribution (ACD) Key (for Sylantro Servers)
The 53i and any attached Expansion Modules support Automatic Call Distribution
(ACD) for Sylantro servers. The ACD feature allows the Sylantro server to distribute
calls from a queue to registered IP phone users (agents).
To use the ACD feature on an IP phone, you must first configure an ACD
programmable key or Expansion Module softkey. When you want to subscribe to a
queue (in order to receive incoming calls), you press the ACD key and the IP phone
UI prompts you to specify the following information:
User ID: the phone number(s) used to login into the queue.
Password: the password used to login to the queue.
Available/unavailable: Shows the current status of the IP phone. Specifies if the IP
phone user is available/unavailable to receive a call from the queue.
After creating an ACD key, you are ready to receive calls from a queue on the server.
You must press the ACD key and then log in by entering your User ID and Password.
An "Available" softkey displays allowing you to make your phone available to accept
these calls.
When you are on an active call, or you miss a call, the server automatically changes
the phone’s status to unavailable. The server updates it’s database with this new
information and no longer distributes calls to the phone. The phone remains in this
"unavailable" state until:
• you make yourself “available” again by pressing the "Available" softkey.
• an ACD timer expires (set by your System Admibnistrator).
You can also choose to manually change the phone status to unavailable by pressing
the "Unavailable" softkey on the phone.
Note: It is recommended you configure no more than a single ACD softkey,
programmable key, or Expansion Module key per IP phone.
Model 53i IP Phone User Guide
53
Line Keys and Programmable Keys
Note: Your System Administrator must provide you with your User ID and
Password to access the applicable phone queue.
Line Keys and Programmable Keys
Configuring an Automatic Call Distribution (ACD) Key
Use the following procedure to configure ACD on the 53i IP Phone.
Aastra Web UI
1. Click on Operation->Programmable Keys.
or
Click on Operation->Expansion Module <N>.
2. Select a "Key 3" through "Key 6".
3. In the "Hard Key" field, select Automatic call distribution.
4. In the "Line" field, select a line to apply Automatic call distribution. Valid values
are 1 through 9.
Note: It is recommended you configure no more than a single ACD programmable key or Expansion Module key per IP phone.
5. Click
to save your changes.
54 Model 53i IP Phone User Guide
Using the ACD Feature on your IP Phone
The ACD feature allows you to login to a phone queue in order to receive distributed
calls on your IP phone. To login to a phone queue, you must preconfigure an ACD
programmable key on your IP Phone as described in the previous procedure.
Your Administrator sets up the queue that you access when you press the ACD Key.
Contact your System Administrator for more information.
When you press the ACD Key, the phone prompts you to enter a User ID and
Password to login into the queue. Once logged in, you can make your phone
“available” or “unavailable” to take calls by pressing the Available/Unavailable Key
(
). The server monitors your IP phone status. When you set the IP phone to
“available,” the server begins distributing calls to your phone. When you set the IP
phone to “unavailable,” the server temporarily stops distributing calls to your phone.
ACD LED Table
This LED changes when you log into the phone queue and are available to take calls.
The LED changes again when you are busy with an active call. The table below
shows the status of the LED as they may appear on your IP phone.
Phone
Model
Status: Logged In
and Available
Status: Unavailable Logged Out
53i
Solid Red LED
Blinking red LED
No LED
Using the ACD Key
Use the following procedure to log into a phone queue from your IP phone.
IP Phone UI
1. Check with your Administrator to verify the queue linked to your ACD Key.
2. Press the ACD Key on your IP phone.
The LCD displays the label of the ACD queue you are accessing.
The "User ID" prompt displays.
ACD: <Queue Label>
User ID:
= Login
= Next
3. Using the keypad, enter your User ID (phone number provided by your System
Administrator) and press the
Key.
The "Password" prompt displays.
ACD: <Queue Label>
Password:
= Login
= Next
Model 53i IP Phone User Guide
55
Line Keys and Programmable Keys
The LED for the ACD Key shows the current status of your phone.
Line Keys and Programmable Keys
4. Using your keypad, enter your Password (provided by your System Administrator) and press the
Key.
5. Press 4 (Login) to login to the queue.
You are logged into the queue and the following screen displays.
ACD: <Queue Label>
= Avail
= Logout
6. To allow your phone to be available in the queue, press
The following screen displays.
(Avail).
ACD: <Queue Label>
= Unavail
= Logout
If your IP phone status is set to “Available” then the server begins to distribute
phone calls from this queue to your IP phone. You must manually change the state
to “Available” in order to start receiving calls.
7. To temporarily stop receiving calls, press the press
(Unavail).
If you are on a call (or miss a call that has been distributed to your phone), your
phone status automatically changes to "Unavailable". Your phone remains in the
"Unavailable" state until one of the following occurs:
• You use the IP Phone UI to manually switch the IP phone state back to
"Available"
or
• The availability “timer” for your IP phone expires. This only occurs if your
Administrator has configured an auto-availability timer on your IP phone.
Contact your System Administrator for more information.
8. To logout of the queue, press 4 (Logout).
The server no longer distributes phone calls to your IP phone.
56 Model 53i IP Phone User Guide
Directed Call Pickup/Group Call Pickup Keys (for Sylantro Servers)
Aastra IP phones support the Directed Call Pickup (DCP) and Group Call Pickup
(GCP) features.
The DCP/GCP feature allows you to intercept - or pickup - a call on a monitored
extension. You can configure this feature using the Aastra Web UI to create a DCP or
GCP softkey on the IP phone. When you configure a DCP softkey, you specify the
extension that you want to monitor. Then, when the monitored extension receives a
call, you press the DCP softkey to pick up the call. If the monitored extension
receives multiple incoming calls simultaneously, the IP Phone UI displays a list of
incoming calls. You select a call from this list, and are connected to the call.
Note: Your System Administrator must configure the extension range for the
Group Call Pickup feature. Contact your System Administrator for more
information.
Configuring Directed Call Pickup (DCP) Key(for Sylantro Servers)
Use the following procedure to configure Directed Call Pickup using the
Aastra Web UI.
Aastra Web UI
1. Click on Operation->Programmable Keys.
or
Click on Operation->Expansion Module <N>.
2. Select a "Key 3" through "Key 6".
3. In the “Type” field, select Directed Call Pickup.
Model 53i IP Phone User Guide
57
Line Keys and Programmable Keys
When you configure a GCP softkey, you specify the ring group (for example,
extensions 2200 - 2210) that you want to monitor for incoming calls. When an
incoming call is received on any of these extensions, the Operator presses the GCP
softkey and is connected to the call. If multiple incoming calls are received
simultaneously, the Operator press the GCP softkey, selects an extension from a list,
and presses the Pickup softkey to answer the call.
Line Keys and Programmable Keys
4. In the “Value” field, specify the extension you want to intercept when you press
this softkey. For example: 2200.
5. In the "Line" field, select the line for which to apply the Directed Call Pickup configuration. Valid values are 1 through 9.
6. Click
to save your changes.
Configuring Group Call Pickup (GCP) Key (for Sylantro Servers)
Use the following procedure to configure Group Call Pickup using the
Aastra Web UI.
Aastra Web UI
Note: A ring group must be configured on the Sylantro Server in order for a
GCP softkey to function.
1. Click on Operation->Programmable Keys.
or
Click on Operation->Expansion Module <N>.
2. Select a key for which to configure Group Call Pickup.
3. In the “Type” field, select Directed Call Pickup.
4. In the “Value” field, enter groupcallpickup.
5. In the "Line" field, select the line for which to apply the Group Call Pickup configuration. Valid value are 1 through 9.
6. Click
to save your changes.
58 Model 53i IP Phone User Guide
Using Directed Call Pickup/Group Call Pickup
Use the following procedure for the DCP/GCP feature on your phone.
IP Phone UI
Note: Before using the DCP/GCP feature on your phone, you must first configure the DCP or GCP Key. You must identify the extension(s) or phone
number(s) you want to monitor when configuring the key. See the previous procedures to configure a DCP or GCP Key.
Using Directed Call Pickup (DCP)
2. Use the
and
keys to scroll through the list to select an extension.
3. Press
(Pickup) Key for the extension you select.
The call is answered.
Using Group Call Pickup (GCP)
1. If any of the monitored group of extensions receives a call, press the GCP Key.
The call is answered.
If the monitored group of extensions receives multiple incoming calls simultaneously, the phone displays a list of incoming calls.
2. Use the
3. Press
and
keys to scroll through the list to select an extension.
(Pickup) Key for the extension you select.
The call is answered.
Select an extension
Press the Pickup
Key to answer
the call
DCP on line:
1. 2201
= Pickup
= Cancel
Model 53i IP Phone User Guide
59
Line Keys and Programmable Keys
1. When the monitored extension receives a call, press the DCP Key to pick up the
call.
If the monitored extension receives multiple incoming calls simultaneously, the
phone displays a list of incoming calls.
Line Keys and Programmable Keys
XML Key
The 53i IP phone has a feature you can enable called "XML" (Extensible Markup
Language). XML is a markup language much like HTML. Your System
Administrator can create customized XML menu services and load them to your IP
phone. These services include things like weather and traffic reports, contact
information, company info, stock quotes, or custom call scripts. You can configure
XML using the Aastra Web UI only.
Using the Aastra Web UI, you can configure a key to access XML applications.
Under Operations->Programmable Keys, you can assign a key the type "XML".
Note: The XML services must be set up by your System Administrator before
you can use the key. Contact your System Administrator for more information.
You must also specify an XML URI and a Services label using the following XML
fields:
• XML Application URI
• XML Application Title
The XML Application URI is the URI loaded by your phone. The phone performs an
HTTP GET. Contact your System Administrator for the applicable XML URI to enter
in the "XML Application URI" field.
The XML Application Title is the label that displays beside the XML softkey on your
phone. If you use the Services key to access the XML features, the "XML
Application Title" is the label that displays on the Services Menu in the IP Phone UI.
Note: Contact your System Administrator for the applicable URI to enter in
this field.
After an XML key is configured, you can use the IP Phone UI to access the XML
applications.
60 Model 53i IP Phone User Guide
Configuring an XML Key
Aastra Web UI
1. Click on Operation->Programmable Keys.
or
Click on Operation->Expansion Module <N>.
4. In the "Value" field, enter a URI(s) to apply to this key.
Note: Contact your System Administrator for the appropriate value to enter in
the "Value" field.
If you specify multiple URIs in the "Value" field, a list of XML applications
appears for selection after pressing the XML key.
5. Click
to save your changes.
Accessing the XML Service
After an XML application(s) have been saved to your IP phone, and after a
programmable key has been configured to access the XML application(s), the
customized service is ready for you to use.
IP Phone UI
1. Press the programmable key configured for XML on the 53i phone. A "Custom
Features" screen displays or the title you specified.
2. Use the
and
to scroll through the customized features.
3. For menu and directory services, select a service to display the information for
that customized service. Message services display to the screen after pressing the
programmable key. For user input services, follow the prompts as appropriate.
4. To exit from the "Customized Features" screen, press the XML programmable
key again.
Model 53i IP Phone User Guide
61
Line Keys and Programmable Keys
2. Select a "Key 3" through "Key 6".
3. In the "Hard Key" field, select XML to apply to the programmable key.
Line Keys and Programmable Keys
Sprecode Key
You can set a programmable key to automatically activate specific services offered
by the server. For example, if the sprecode value of *82 is configured, then by
pressing the Sprecode programmable key, *82 automatically activates a service
provided by the server. Contact your System Administrator for information about
available services.
Aastra Web UI
Configuring a Sprecode Key
Use the following procedure to configure a sprecode programmable key on the 53i
phone.
1. Click on Operation->Programmable Keys.
2. Select a key from "Key 3" through "Key 6".
3. In the "Hard Key" field, select sprecode.
4. In the "Label" field, enter a label to display on the IP phone for this programmable
key.
5. In the "Value" field, enter the appropriate value for accessing specific services
from the server.
Note: For values to enter in this field, contact your System Administrator.
6. Click
to save your changes.
62 Model 53i IP Phone User Guide
Park/Pickup Keys
The 53i phone has a park and pickup call feature that allows you to park a call and
pickup a call when required.
The IP phones support the Park/Pickup feature on the Asterisk, BroadWorks,
Sylantro, and ININ PBX servers.
You can set the programmable keys on the 53i to use the park/pickup feature by
setting a programmable key as "Park" or "Pickup" and then:
• specify a value
• specify a line to use
Note: The values you enter for each programmable key are dependent on the
type of server you are using (Asterisk, BroadWorks, Sylantro, or ININ
PBX).
• When a call comes in and you pickup the handset, you can press the applicable "Park" programmable key to park the call.
• After the call is parked, you can press the "Pickup" programmable key, followed by the applicable value to pickup the call.
You configure a Park and Pickup programmable configuration using the Aastra Web
UI.
The following table provides the values you enter for the "Park Call" and "Pickup
Parked Call" fields in the Aastra Web UI.
Park/Pickup Call Server Configuration Values
Server
Park Values*
Pickup Values*
Aasterisk
700
700
Sylantro
*98
*99
BroadWorks
*68
*88
ININ PBX
callpark
pickup
*Leave "value" fields blank to disable the park and pickup feature.
Model 53i IP Phone User Guide
63
Line Keys and Programmable Keys
The park/pickup feature performs as follows:
Line Keys and Programmable Keys
Configuring Park/Pickup Keys
Aastra Web UI
Use the following procedure to configure park/pickup on the 53i phone.
1. Click on Operation->Programmable Keys.
2. Select two keys from "Key 3" through "Key 6".
3. In the "Hard Key" field, select Park for the first key. For the second key, select
Pickup.
4. In the "Value" fields, enter the appropriate values based on the server in your network.
Note: For values to enter in this field, see the table "Park/Pickup Call Server
Configuration Values" on page 63.
5. In the "Line" field, select the lines for which to apply the Park and pickup configuration. Valid values are 1 through 9.
6. Click
to save your changes.
64 Model 53i IP Phone User Guide
Using the Park Call/Pickup Parked Call Feature
Use the following procedure on the IP phone to park a call and pick up a parked call.
Park a Call
1. While on a live call, press the "Park" programmable key.
2. Perform the following for your specific server:
For Asterisk Server
- Server announces the extension number where the call
has been parked. Once the call is parked, press the
key to complete parking.
For BroadWorks Server
For Sylantro Server
- Enter the extension number where you want to park the
call, followed by "#" key.
For ININ Server
- Enter the extension number where you want to park the
call, followed by "#" key.
If the call is parked successfully, the response is either a greeting voice confirming
that the call was parked, or a hang up occurs. The parked call party hears music on
hold.
3. If the call fails, you can pick up the call (using the next procedure) and press the
"Park" programmable key again to retry step 2.
Pickup a Parked Call
1. Pick up the handset on the phone.
2. Enter the extension number where the call was parked.
3. Press the "Pickup" programmable key.
If the call pick up is successful, you are connected with the parked call.
Model 53i IP Phone User Guide
65
Line Keys and Programmable Keys
- After you hear the greeting from the CallPark server,
enter the extension where you want to park the call.
Line Keys and Programmable Keys
Last Call Return (lcr) Key (for Sylantro Servers)
Using the Aastra Web UI, you can configure the "Last call return" (lcr) function on a
key. This feature is for Sylantro servers only.
How it works
If you configure "lcr" on a key, and a call comes into your phone, after you are
finished with the call and hang up, you can press the key configured for “lcr” and the
phone dials the last call you received. When you configure an “lcr” key, the label
“LCR” displays next to that key on the IP phone. When the Sylantro server detects an
“lcr” request, it translates this request and routes the call to the last caller.
Configuring a Last Call Return Key
Aastra Web UI
1. Click on Operation->Programmable Keys.
or
Click on Operation->Expansion Module <N>.
2. Select from "Key 3" through "Key 6".
3. In the "Type" field, select Last Call Return.
4. In the "Line" field, select the line to apply this feature.
Valid values are 1 through 9.
5. Click
to save your changes.
66 Model 53i IP Phone User Guide
Directory Key
By default, the 53i has a Directory key configured on Key 3. However, using the
Aastra Web UI, you can assign the Directory key to another available key if required
(Key 3 through Key 6)..
Directory
Key
Reference
For more information about the Directory List, see "Directory List" on page 94.
Configuring a Directory Key
Aastra Web UI
Use the following procedure to configure a Directory key on the 53i phone.
Note: Key 3 is set as a Directory key by default.
1. Click on Operation->Programmable Key.
or
Click on Operation->Extension Module <N>.
2. Select from "Key 3" through "Key 6".
3. In the "Type" field, select Directory.
4. Click
to save your changes.
Model 53i IP Phone User Guide
67
Line Keys and Programmable Keys
The "Directory List" feature allows you to store frequently used names and numbers
on the phone. You can also dial directly from a directory entry.
You can use the Directory key to access a Directory List which contains a customized
list of names with phone numbers and labels.
In addition to creating a Directory key, you can also download a Directory List to
your PC if required using the Aastra Web UI.
Line Keys and Programmable Keys
Callers List Key
By default, the 53i has a Callers List key configured on Key 4. However, using the
Aastra Web UI, you can assign the Callers List key to another available key if
required (Key 3 through Key 6).
Callers List
Key
The Callers list is a stored log of your incoming calls. You can use the Callers List
key to access a list of callers that called your phone.
Reference
For more information about the Callers List, see "Callers List" on page 104.
Configuring a Callers List Key
Aastra Web UI
Use the following procedure to configure a Callers List key on the 53i phone.
Note: Key 4 is set as a Callers List key by default.
1. Click on Operation->Programmable Keys.
or
Click on Operation->Extension Module <N>.
2. Select from "Key 3" through "Key 6".
3. In the "Type" field, select Callers List.
4. Click
to save your changes.
68 Model 53i IP Phone User Guide
Transfer Key
By default, the 53i has a Transfer key configured on Key 5. However, using the
Aastra Web UI, you can assign the Transfer key to another available key if required
(Key 3 through Key 6).
Transfer
Key
Reference
For more information about using blind and consultative call transfers, see
"Transferring Calls" on page 85.
Configuring a Transfer Key
Aastra Web UI
Use the following procedure to configure a Transfer key on the 53i phone.
Note: Key 5 is set as a Transfer key by default.
1. Click on Operation->Programmable Keys.
or
Click on Operation->Extension Module <N>.
2. Select from "Key 3" through "Key 6".
3. In the "Type" field, select Transfer.
4. Click
to save your changes.
Model 53i IP Phone User Guide
69
Line Keys and Programmable Keys
The Transfer key allows you to perform blind or consultative call transfers to other
recipients. The blind transfer feature transfers a call to another number without you
having to talk to the recipient. A consultative transfer feature transfers a call to
another number but allows you to speak with the recipient before the call is actually
transferred.
Line Keys and Programmable Keys
Conference Key
By default, the 53i has a Conference key configured on Key 6. However, using the
Aastra Web UI, you can assign the Conference key to another available key if
required (Key 3 through Key 6).
Conference
Key
The Conference key allows you to link three active calls into a single conference
(Local Conferencing). This key also helps to create multiple conferences with
unlimited participants on your phone if your System Administrator has enabled
Centralized Conferencing on your phone.
Reference
For more information about Local and Centralized Conferencing, see "Conferencing
Calls" on page 87.
Configuring a Conference Key
Aastra Web UI
Use the following procedure to configure a Conference key on the 53i phone.
Note: Key 6 is set as a Conference key by default.
1. Click on Operation->Programmable Keys.
or
Click on Operation->Extension Module <N>.
2. Select from "Key 3" through "Key 6".
3. In the "Type" field, select Conference.
4. Click
to save your changes.
70 Model 53i IP Phone User Guide
Intercom Key
By default, the IP phone allows incoming intercom calls to be automatically
answered without having to set up an Icom key on your phone. For more information
about changing the behavior of incoming Intercom calls, see the section "Incoming
Intercom Call Features" on page 129.
Your System Administrator can enable outgoing intercom calls on your phone. If
enabled, you must configure an Icom key on your phone to use for outgoing intercom
calls.You must configure a programmable key with the function, “Intercom”.
Use the following procedure to configure a programmable key as an Icom key using
the Aastra Web UI.
Configuring an Intercom Key
Line Keys and Programmable Keys
Aastra Web UI
1. Click on Operation->Programmable Keys.
or
Click on Operation->Expansion Module <N>.
2. Select from "Key 3" through "Key 6".
3. In the "Type" field, select Intercom from the list of options.
4. Click
to save your changes.
Model 53i IP Phone User Guide
71
Line Keys and Programmable Keys
Using the Icom Key (for Outgoing Intercom Calls)
IP Phone UI
1. Press the Icom key.
2. Enter the extension number of the person you want to intercom or the BLF softkey
for that extension.
3. After a beep tone, your phone automatically connects with the remote extension
and you can speak through its speaker.
4. To cancel intercom, press
or hang up the handset.
5. When you are finished speaking, hang up the phone by placing the handset back
on-hook or by pressing
or the line/call appearance button for the active
call. When you hang up, the remote phone also hangs up.
Reference
For more information about incoming intercom calls, see "Incoming Intercom Call
Features" on page 129. For more information about outgoing intercom calls, see
"Available Features Enabled by Administrators" on page 132.
72 Model 53i IP Phone User Guide
None Key
You can set a key to force a blank entry on the IP phone display for a specific key.
You do this by setting the key to "none". If a particular key is not defined, it is
ignored.
Setting a None Key
Aastra Web UI
Use the following procedure to configure a None key on the 53i IP Phone.
1. Click on Operation->Programmable Keys.
or
Click on Operation->Expansion Module <N>.
Line Keys and Programmable Keys
2. Select from "Key 3" through "Key 6".
3. In the "Type" field, select None.
4. Click
to save your changes.
Model 53i IP Phone User Guide
73
Line Keys and Programmable Keys
Phone Lock Key
You can configure a programmable key on the phone to use as a lock/unlock key. You
assign the function of the key as “Phone Lock”.
Use the following procedure to configure a programmable key as a lock/unlock key
in the Aastra Web UI.
Configuring a Phone Lock Key
Aastra Web UI
1. Click on Operation->Programmable Keys.
or
Click on Operation->Expansion Module <N>.
2. Select from "Key 3" through "Key 6".
3. In the "Type" field, select Phone Lock from the list of options.
4. Click
to save your changes.
Note: You can lock/unlock the phone using the new key you just configured,
using the Aastra Web UI at the path Operation->PhoneLock, or using
the "Phone Lock" option on the IP Phone UI at the path Options>Phone Lock. For more information about using the lock/unlock feature,
see "Phone Lock" on page 35.
74 Model 53i IP Phone User Guide
Using the Lock/Unlock Key on the IP Phone
After configuring a programmable key as a lock/unlock key, refer to the following
procedure to use the key on the IP phone.
IP Phone UI
Lock the Phone
1. Press the Lock programmable key.
The phone locks.
The LED for the programmable key AND the Message Waiting Lamp illuminate
steady ON. An “Unlock” label appears next to the programmable key you just
pressed.
Line Keys and Programmable Keys
Unlock the Phone
1. Press the Unlock programmable key.
A password prompt displays.
2. Enter your user password and press ENTER.
The phone unlocks.
The LED for the programmable key AND the Message Waiting Lamp go OFF.
The “Lock” label appears next to the programmable key you just pressed.
Model 53i IP Phone User Guide
75
Line Keys and Programmable Keys
Deleting a Key
Aastra Web UI
Use the following procedure to delete a programmable key function using the Aastra
Web UI.
1. Click on Operation->Programmable Keys.
or
Click on Operation->Expansion Module <N>.
2. Select from "Key 3" through "Key 6".
3. In the "Type" field, select none from the list of options.
4. Click
to save your changes.
The programmable function is deleted from the IP phone memory.
76 Model 53i IP Phone User Guide
Making Calls
This section describes ways to make calls on your 53i phone, using your handset,
speakerphone or headset.
Dialing a Number
First, take the phone off-hook by:
• lifting the handset
• pressing
or
• pressing a line/call appearance button.
At the dial tone, enter the number you wish to call.
Note: After dialing the number, the phone has a short delay before sending the
call. To send the call immediately, you can press the "#" key immediately after dialing the number. The phone sends the call without delay.
If you are unable to make calls within certain area codes, check with your System
Administrator for any toll restrictions placed on your extension that may restrict your
access to long distance area codes or dialing prefixes.
=Dial
When your party picks up, a timer appears on your display that records the length of
your call.
If the Live DialPad option is on, as soon as you press the first digit on the dial pad the
phone automatically selects the next available line, go off-hook and dial as digits are
pressed.
Making Calls
Model 53i IP Phone User Guide
77
Making Calls
Using Handsfree Speakerphone
The handsfree feature allows you to speak to someone without using the handset or
headset. Your phone must be in either the Speaker or Speaker/Headset audio mode.
For more information about setting the audio mode on your phone, see "Set Audio"
on page 24.
IP Phone UI
• To dial using handsfree, first press
tone.
and enter a number at the dial
• To answer a call on your phone using handsfree, press
appearance button.
or the line/call
• If you are in Speaker audio mode, lift the handset and press
between handsfree and handset.
• If you are in Speaker/headset audio mode, press
handsfree and headset.
• When the handset is on hook, press
When handsfree is on, the speaker light turns on.
78 Model 53i IP Phone User Guide
to switch
to switch between
to disconnect the call.
Using a Headset
The 53i accepts headsets through the modular RJ9 jack on the back of the phone.
Contact your telephone equipment retailer or distributor to purchase a compatible
headset.
Note: Customers should read and observe all safety recommendations contained in headset operating guides when using any headset.
Advanced Volume Controls for the Headset Mic
On the 53i, there are 3 options for the headset microphone volume. For more
information about the headset microphone, see "Headset Mic Volume" on page 25.
IP Phone UI
To change the volume:
1. Press
to enter the Options list.
2. Select Preferences and press 4.
3. Use
to scroll down to Set Audio and press 4 to select.
4. Press
to scroll down to Headset/Mic Volume and press 4 to select.
5. Use
to scroll down the list and press 4 to select your desired volume.
6. Press 4 to save changes and 3 to exit.
7. If you do not wish to save changes, press 3 to return to the previous screen.
Note: By default, the volume for the headset microphone is set to medium.
Making and Receiving Calls Using a Headset
1. Ensure that you have selected a headset audio mode by accessing the Options list
(under option Preferences->Set Audio->Audio Mode on the IP Phone).
2. Plug the headset into the jack.
3. Press the
key to obtain a dial tone or to answer an incoming call. Depend-
ing on the audio mode selected from the options menu, a dial tone or an incoming
call is received on either the headset or the handsfree speakerphone.
4. Press the
key to end the call.
Model 53i IP Phone User Guide
79
Making Calls
IP Phone UI
Making Calls
Redial
IP Phone UI
• Press
to dial the most recent number you dialed from the phone.
• If you are off-hook and press
the last number you called is called
back.
• If you are on-hook and press
, a Redial Directory list appears on-
screen.
The redial list is available during active calls. It stores up to the last 100 numbers you
called, allowing you to scroll through and select the number you wish to redial.
Note: Your System Administrator can set your Redial key to speeddial a specific number. Contact your System Administrator for more information.
Accessing the Redial List
IP Phone UI
1. If you are off-hook and press
, the telephone automatically dials the last
number you called.
2. If you are not on the phone, press
number and use
and
to display the most recently dialed
to scroll through the list to view the other numbers.
3. Press
to see the second most recently dialed number, or
call on your list.
4. To dial the displayed number press
to see the oldest
, or lift the Handset or press any line
keys.
5. Press
or the
key to cancel.
Note: The redial list is available during active calls. It also stores up to the last
100 numbers you called, allowing you to scroll through and select the
number you wish to redial.
80 Model 53i IP Phone User Guide
Deleting from the Redial List
Note: You cannot delete individual entries in the Redial List.
IP Phone UI
Delete All Items
1. Press
.
2. Press the Delete Key, then press the Delete Key again at the prompt to erase all
items.
DELETE again to
erase all items
Redial List is
empty
Mute
You can use the Mute
key to mute the handset, headset, or speakerphone.
When you use the mute key on your phone, you cannot be heard on an active call or
on a conference.
When a call is muted, the icon displays as follows.
1
Making Calls
John Burns
9054550055
03:00
For muted calls, the handsfree LED flashes and the Mute key LED is ON.
Model 53i IP Phone User Guide
81
Making Calls
IP Phone UI
Press the
button at any time to mute handset, headset, or handsfree.
The speaker light flashes slowly and you can hear the caller, but they cannot hear
you. To switch mute on or off, press
.
Note: If you place a muted call on hold, the phone automatically takes the call
off mute when you reconnect to the call.
82 Model 53i IP Phone User Guide
Receiving Calls
When a call is ringing at your extension, you see the "Inbound Call" Screen. The line/
call appearance light flashes quickly for the incoming call.
Laflamme & Assoc
555-1234
Answering an Incoming Call
IP Phone UI
To answer the call
• For handsfree operation, press
or the line/call appearance button for
the incoming call.
• Press
for handsfree or headset operation.
Note: The audio mode setting you have selected in the options list under Set
Audio->Audio Mode determines if the call goes to handsfree or headset operation. For more information, see "Set Audio" on page 24.
• Lift the handset for handset operation.
If the phone is already connected to a call, pressing the line/call appearance button
for the new incoming call automatically places the connected call on hold and
answers the new call. To reconnect to a party, press the line/call appearance button
for that call.
If you cannot answer the call, the caller goes to voicemail has been configured for
your extension.
button can be used to cancel the call pickup procedure.
Sending an Incoming Call to Voicemail
You can send an incoming call directly to voicemail without answering the call. To
do this, press
without picking up the handset. If you're already on the phone
your incoming call should go directly to voicemail. Your phone screen displays a
voicemail icon (
) along with the number of waiting messages, if you have
unheard messages
(example:
x4).
Model 53i IP Phone User Guide
83
Receiving Calls
Note: The
Handling Calls
Handling Calls
When you are connected to a call, you can use the hard keys or programmable keys
on the phone to place a call on hold, transfer a call, or conference.
Placing a Call on Hold
You can place an active call on hold by pressing the Hold
place a call on hold, only your phone can retrieve the call.
key. When you
When a call is on hold, the icon displays on-hook as follows.
1
Call held
03:05
For on-hold calls, the timer displays as running and the Line and main LEDs flash.
IP Phone UI
To place a call on hold
1. Connect to the call (if not already connected).
2. Press the Hold
key.
Call held
Jun 8 2:55pm
The line/call appearance light begins to flash slowly and after a short time the phone
beeps softly to remind you that you still have a call on hold. The screen displays
"Call Held" with the line number the call is held at the phone.
Note: If you are connected to another call, the phone does not beep to remind
you that you still have a call on hold.
When on Hold
To let your caller know that they are still on hold, music plays softly (if this has been
set up for your system). The call/line appearance light for the line you are on remains
solid to indicate that you are still connected.
John 1051
01:17
84 Model 53i IP Phone User Guide
Automatic Hold
When juggling between calls, you do not have to press the hold button to go from one
call to the next. The phone automatically puts your current call on hold as soon as
you press a new line/call appearance button. If you have more than one call on hold,
you can reconnect to a held call by pressing the line/call appearance button where
that call is being held. Press
to disconnect the call.
Retrieving a Held Call
If you have more than 1 call on hold, you can scroll through the held call information
by pressing 3 and 4 navigation keys. To reconnect to a call press the line/call
appearance button where that call is being held. If you press the call/line appearance
button again, you disconnect from the call.
Transferring Calls
Blind Transfer
A blind transfer is when you transfer a call directly to another extension without
consulting with the person receiving the call. To do this, simply complete the transfer
immediately after you have entered the number. The call goes directly to the
extension or outside line you transferred to. If the party you are transferring the call
to does not answer, the transferred call rings back to your extension.
Consultive Transfer
You also have the option to consult with the person you are transferring the call to,
before you complete the transfer. To do this, remain on the line until the receiving
party answers the call. After consulting with the receiving party, you can either
complete the transfer or cancel the transfer to go back to the original call.
IP Phone UI
Use the following procedure to transfer a call to another extension. Use the following
illustration as a reference.
Handling Calls
Transfer
Key
Model 53i IP Phone User Guide
85
Handling Calls
1. Connect to Party 1 (if not already connected). Party 1 is the party you want to
transfer.
2. Press the Transfer Key. You should hear a dial tone as a second line opens up.
3. Dial the extension number (or the outside number) to Party 2. This is the Party for
which you want to transfer Party 1.
4. To complete a "blind" transfer, press the Transfer Key again before the receiving
end answers. To complete a consultive transfer, remain on the line to speak with
the Party 2, before pressing the Transfer Key again to transfer Party 1 to Party 2.
To cancel the transfer, select Cancel on the display screen.
86 Model 53i IP Phone User Guide
Conferencing Calls
The 53i IP phone offers two methods of conferencing:
• Local conferencing (default method).
• Centralized conferencing (for Sylantro and Broadsoft Servers) (Administrator
must enable this method).
By default, the Conference key is Key 6 on your phone. A Conference key must be
set up on your phone before you can set up conference calls. To assign a key as a
Conference key, see "Conference Key" on page 70.
Conference State Screens
When you use the Conference key to initiate a conference call, the following screen
displays.
1-1
1-2
John
Jim
03:05
= Drop
In a conference call, the call timer moves to the left. You use the up and down arrow
keys to scroll to a party on the list. You use the right arrow key to select the party to
drop.
Local Conferencing
The 53i phone supports up to 3 parties (including yourself) in a conference call. This
is called Local Conferencing and is the default method of conferencing on the 53i.
Note: Your System Administrator can set your Conference key to speeddial a
specific number. Contact your System Administrator for more information.
Handling Calls
Model 53i IP Phone User Guide
87
Handling Calls
Using Local Conferencing
IP Phone UI
Use the following procedure to create a conference call using local conferencing. Use
the following illustration as a reference.
Conference
Key
1. When you begin a conference, you are the first party in the conference (Party 1).
Pickup the handset or press the speakerphone key.
A line opens up.
2. Call Party 2 by dialing their number (or answer an incoming call of a Party).
3. Wait for Party 2 to answer. When Party 2 answers, you can consult with them
before adding them to the conference.
4. Press the Conf Key. A new line opens.
2
=Dial
5. Enter the phone number of Party 3.
6. Wait for Party 3 to answer. When Party 3 answers, you can consult with them
before adding them to the conference.
7. Press the Conf key again to add Party 3 to the conference. Party 1 (which is yourself), Party 2, and Party 3 are all connected to a single conference.
8. To drop a party from the conference, press the Conf key once more.
Note: You can use
and
to scroll through and see the numbers and
names (if available) of the parties in the conference call. When a name is
displayed, pressing 4 drops the displayed party from the call.
88 Model 53i IP Phone User Guide
Joining Two Active Calls in a Single Conference
IP Phone UI
1. Begin with active calls on two different lines (for example, Line 1 and Line 2 have
active calls).
2. Press the Line key for which you want to conference the two calls together (for
example, Line 1).
3. Press the Conf key.
4. Press the Line key that has the second active call (for example, Line 2).
5. Press the Conf key. The two active calls link into a conference call on Line 1.
Note: You can use
and
to scroll through and see the numbers and
names (if available) of the parties in the conference call. When a name is
displayed, pressing 4 drops the displayed party from the call.
Handling Calls
Model 53i IP Phone User Guide
89
Handling Calls
Centralized Conferencing (for Sylantro and Broadsoft Servers)
The 53i allows you to create multiple conferences with unlimited participants
(depending on your server limitations) when your Administrator enables Centralized
Conferencing.
If your Administrator does not enable Centralized Conferencing, then the 53i uses
Loca Conferencing by default.
Your Administrator can configure Centralized Conferencing globally on all lines or
on specific lines. Although, for the global setting to work, you must configure the
lines with the applicable phone number.
Reference
For more information on Centralized Conferencing, see "Centralized Conferencing"
on page 133 or contact your System Administrator.
Using Centralized Conferencing
IP Phone UI
Note: When Centralized Conferencing is enabled on your phone, local conferencing (or three-way conferencing) works as indicated in the previous
section, “Using Local Conferencing.” Joining two active calls in a conference also works as indicated in the previous section, “Joining Two
Active Calls in a Single Conference.”
Use the following procedure to create a conference call using centralized
conferencing. Use the following illustration as a reference.
Conference
Key
90 Model 53i IP Phone User Guide
Setting Up a Conference and Adding Multiple Parties
(for Sylantro and Broadsoft Servers)
Note: You can have an unlimited number of parties in a conference (dependent
on the limitations of the server.
1. When you begin a conference, you are the first party in the conference (Party 1).
Pickup the handset or press the Speakerphone Key.
A line opens up.
2. Call Party 2 by dialing their number (or answer an incoming call of a Party).
3. Wait for Party 2 to answer. When Party 2 answers, you can consult with them
before adding them to Conference 1.
4. Press the Conf Key. A new line opens.
2
=Dial
5. Enter the phone number of Party 3.
6. Wait for Party 3 to answer. When Party 3 answers, you can consult with them
before adding them to the Conference 1.
7. Press the Conf Key again to add Party 3 to Conference 1. Party 1 (which is yourself), Party 2, and Party 3 are all connected to Conference 1.
8. Press an available Line Key (or answer an incoming call on an available line). If
calling out, call Party 4.
9. Wait for Party 4 to answer. When Party 4 answers, you can consult with them
before adding them to the conference.
10.Press the Conf Key to add Party 4 to Conference 1.
11.Press the Line Key that has Conference 1.
12.Press the Conf Key to join all parties (Parties 1 through 4) on Conference 1.
Note: You can use
and
Handling Calls
13.To add more parties, repeat steps 8 through 12.
to scroll through and see the numbers and
names (if available) of the parties in the conference call. When a name is
displayed, pressing 4 drops the displayed party from the call.
If any party in the conference hangs up (including the party that began the
conference), all other parties in the conference are still connected.
Model 53i IP Phone User Guide
91
Handling Calls
Setting Up Multiple Conferences (for Sylantro Server only)
Note: The 53i is limited to 9 conferences (a single conference each on lines 1
through 9).
1. Start Conference 1 using the procedures in the previous section, "Setting Up a
Conference and Adding Multiple Parties (for Sylantro and Broadsoft Servers)".
2. When you are finished adding all required parties to Conference 1, press an available Line Key to start Conference 2. You are Party 1 on Conference 2. Call Party
2.
3. When Party 2 answers, press the Conf Key.
4. Press an available Line Key.
5. Call Party 3 for Conference 2.
6. When Party 3 answers, press the Conf Key to join Parties 1 (which is yourself),
Party 2, and Party 3 on Conference 2.
You now have two active conferences on two different lines.
Note: When you are connected to multiple conference calls, and you put a conference on hold, the conference may be on hold for a limited period of
time before it is disconnected. Contact your System Administrator for
more information.
If any party in a conference hangs up (including the party that began the conference),
all other parties in the conference are still connected.
Joining Additional Parties to Active Conferences
In centralized conferencing, you can join multiple incoming or outgoing calls to
active conferences. Before following this procedure, at least one active conference
must exist on your phone.
1. As Party 1, pickup the handset or press the speakerphone key.
A line opens up.
2. Call Party 2 by dialing their number (or answer an incoming call of a Party).
3. Wait for Party 2 to answer. When Party 2 answers, you can consult with them
before adding them to the conference.
4. Press the Conf Key.
5. Press the Line Key that has the active conference. (For example, Line 1 and Line
2 both have active conferences. Pressing Line 1 joins Party 1 and Party 2 to the
conference on Line 1. Pressing Line 2 joins Party 1 and Party 2 to the conference
on Line 2.)
6. Press the Conf Key again to join the Parties to the active conference.
92 Model 53i IP Phone User Guide
Ending Calls
IP Phone UI
To end a call, you first need to connect or reconnect to the call if not already connected
(for example, if your caller is on hold). Press
or the line/call appearance
button of the active call to end the call. If connected through the handset, you can also
place the handset back on hook to end the call.
Handling Calls
Model 53i IP Phone User Guide
93
Managing Calls
Managing Calls
The 53i has several features that make it easier to manage calls, and to keep track of
your caller history, as well as your business and personal contacts.
These features include:
•
•
•
•
•
Directory List
Callers List
Call Forwarding
Missed Calls Indicator
Voicemail
Directory List
The Directory List is your personal phone book, conveniently stored within your
phone. You can enter up to 200 entries into the 53i Directory by adding them
manually, or by saving the number and name from other lists stored on your phone.
You can also dial directly from a directory entry. Each entry can contain a maximum
of 16 letters and numbers. On the 53i, you access the Directory by pressing the
Directory Key (Key 3).
Accessing Your Directory
IP Phone UI
Use the following procedure to access your Directory List. Use the following
illustration as a reference.
Directory
Key (Key 3)
1. Press the Directory Key (Key 3). The directory displays the number of entries in
your list. If the Directory list is empty, "Directory Empty/Use Save to add" is displayed.
Directory empty
Use Save to add
2. You can access entries by pressing
94 Model 53i IP Phone User Guide
and
to scroll through the list.
3. To search for an entry by name, press the dial pad number corresponding to the
first letter of the name (for example, press 7 for the letter P). Continue to press the
dial pad number to access other letters on the same key (for example, press 7 three
times for ‘Ron’). If there are multiple entries under the same letter, you can use
and
to scroll through the list, or continue to press the next letters of the
name to find a better match.
4. To dial the displayed number press
or just lift the handset or press any
Line Key.
5. Press the Directory Key to cancel.
Sorting Entries and Quick Search Feature
You can also sort multiple numbers according to preference and perform a quicksearch feature that allows you to enter the first letter that corresponds to a name in the
Directory to find specific line items. The phone displays the first name with this
letter.
Note: The quick-search feature in the Directory List works only when the
Directory is first accessed.
Managing the Directory List
From the Directory List in the IP Phone UI, you can perform the following:
•
•
•
•
Add a new entry
Edit an entry
Delete an entry
Save entries to the Directory List
- Save from the Display
- Save from the Caller List
- Save from the Redial List
Managing Calls
Model 53i IP Phone User Guide
95
Managing Calls
Adding an Entry to the Directory List
IP Phone UI
Use the following procedures to add a new entry to the Directory List. Use the
following illustration as a reference.
Save Key
Delete Key
Directory
Key
Notes:
1.Use the 3 Key when required for backspacing.
2.You can exit the entry process any time by pressing the
Key.
1. Press the Directory Key (Key 3).
2. Press Save (Key 1).
The "Enter Number" prompt displays.
3. Enter a phone number using the numbers on the keypad and press Save. To backspace and erase a mistake, press 3 or press the Delete Key (Key 2).
The "Press 1st letter to enter name" prompt displays.
4. Enter a name to associate with the phone number you just entered, and press Save.
Use the keypad to select the letters. Continue to press the number key to access
the next letter for that key (for example, press 2 three times to access C). Press 4
to move to the next space, or wait a moment and the cursor automatically
advances. To insert a space between letters, press 4. To backspace and erase a
mistake, press 3 or press the Delete Key.
The "Line" prompt displays. The default is Line 1.
5. If you want to save the new Directory entry to use Line 1, press Save to save the
new entry to the Directory List.
Key to select a difIf you want the new entry to use a different line, use the
ferent Line and press Save.
The new entry you added is saved to the Directory List.
Saved: Directory
John Burns
96 Model 53i IP Phone User Guide
Adding an Entry to the Directory List from the Save Key
You can also add a new entry to the Directory List from the Save Key (Key 1).
Notes:
1.Use the 3 Key when required for backspacing.
2.You can exit the entry process any time by pressing the
Directory Key.
Key or the
1. Press the Save Key.
The "Save to?" prompt displays.
2. Press the Directory Key.
The "Enter Number" prompt displays.
3. Enter a phone number using the numbers on the keypad and press Save. To backspace and erase a mistake, press 3 or press the Delete Key (Key 2).
The "Press 1st letter to enter name" prompt displays.
4. Enter a name to associate with the phone number you just entered, and press Save.
Use the keypad to select the letters. Continue to press the number key to access
the next letter for that key (for example, press 2 three times to access C). Press 4
to move to the next space, or wait a moment and the cursor automatically
advances. To insert a space between letters, press 4. To backspace and erase a
mistake, press 3 or press the Delete Key.
The "Line" prompt displays. The default is Line 1.
5. If you want to save the new Directory entry to use Line 1, press Save to save the
new entry to the Directory List.
If you want the new entry to use a different line, use the
Key to select a different Line and press Save.
The new entry you added is saved to the Directory List.
Saved: Directory
John Burns
Managing Calls
Model 53i IP Phone User Guide
97
Managing Calls
Editing an Entry in the Directory List
IP Phone UI
Use the following procedure to edit an entry in the Directory List. Use the following
illustration as a reference.
Save Key
Directory
Key
1. Press the Directory Key.
2. Access the entry you want to edit by pressing the first letter of the name on the dial
pad, or use
and
to scroll through the list to find the name.
3. To begin editing, press 3. Press 3 again to erase the numbers or letters to the left
or use the dial pad to enter additional digits or characters once you have saved the
number.
If you don't want to change the number or name just press the Directory Key or
the
Key at any time to exit.
4. Press the Save Key to finish.
98 Model 53i IP Phone User Guide
Deleting an Entry from the Directory List
You can delete a single entry from the Directory List, or you can delete all entries
from the Directory List.
IP Phone UI
Use the following procedures to delete a single entry or all entries from the Directory
List. Use the following illustration as a reference.
Delete Key
Directory
Key
Delete a Single Entry
1. Press the Directory Key.
2. Press
and
to find the entry you want to delete.
3. Press the Delete Key.
The "DELETE again to erase this item" prompt displays.
Managing Calls
DELETE again to
erase this item
4. Press the Delete Key again at the prompt to erase the entry.
Delete All Entries
1. Press the Directory Key.
2. Press the Delete Key.
The "DELETE again to erase all items" prompt displays.
DELETE again to
erase all items
Model 53i IP Phone User Guide
99
Managing Calls
3. Press the Delete Key again to erase all entries from the Directory List.
The "Directory empty" prompt displays..
Directory empty
Use Save to add
Saving an Entry to the Directory List
You can save entries (names and numbers) from other sources to your Directory
using any of the following methods:
• Saving from the Display
• Saving from the Caller List
• Saving from the Redial List
Saving from the Display
IP Phone UI
You can save the name and/or number displayed on your screen during a call to the
Directory List, or to one of your programmable keys using the following procedure.
Use the following illustration as a reference.
Save Key
Directory
Key
1. Press the Save Key during the call.
Save to?
John Burns
9054550055
2. Press the Directory Key or an empty programmable key. If a name is displayed
both the number and name are saved in the Directory List or the programmable
key. If no name or "Unknown Name" displays, you can enter the name using the
dial pad.
3. Press the Save Key to finish.
100 Model 53i IP Phone User Guide
Saving from the Callers List
IP Phone UI
Use the following procedure to save names/numbers from the Callers List to the
Directory. Use the following illustration as a reference.
Save Key
Directory
Key
Callers List
Key
1. Press the Callers List Key (Key 4).
2. From the Callers List, scroll through the list to find the name and number that you
want to save to your Directory.
3. Press the Save Key.
4. Press the Directory Key to save the number you selected to the Directory List. If
the name is displayed with the number, both are saved to the Directory. If no
name is displayed, you can enter the name using the dial pad.
Managing Calls
Model 53i IP Phone User Guide 101
Managing Calls
Saving from the Redial List
IP Phone UI
Use the following procedure to save names/numbers from the Redial List to the
Directory. Use the following illustration as a reference.
Save Key
Directory
Key
Redial List
Key
1. Press the Redial List Key (
).
2. From the Redial List, scroll through the list to find the name and number that you
want to save to your directory.
3. Press the Save Key.
4. Press the Directory Key to save the number you selected to the Directory List. If
the name is displayed with the number, both are saved to the Directory. If no
name is displayed, you can enter the name using the dial pad.
102 Model 53i IP Phone User Guide
Downloading the Directory List to Your PC
You can download the Directory List to your PC via the Aastra Web UI. The phone
stores the directorylist.csv file to your PC in comma-separated value (CSV) format.
You can use any spreadsheet application to open the file for viewing. The following
is an example of a Directory List in a spreadsheet application. The file displays the
name, phone number, and line number for each Directory entry.
Note: Your System Administrator can populate your IP phone Directory List
with server directory files. Contact your System Administrator for more
details.
Download the Directory List
Use the following procedure to download the Directory List to your PC using the
Aastra Web UI.
Aastra Web UI
1. Click on Operation->Directory.
.
3. Click OK.
4. Enter the location on your computer where you want to download the Directory
List and click SAVE.
The callerslist.csv file downloads to your computer.
5. Use a spreadsheet application to open and view the Directory List.
Model 53i IP Phone User Guide 103
Managing Calls
2. In the Directory List field, click on
A File Download message displays.
Managing Calls
Callers List
The Callers list is a stored log of your incoming calls. The 53i IP Phone stores
information for up to 200 incoming calls in the Callers list.
By default, the Callers List Key is Key 4 on the top left of your phone.
Callers List Key
Note: Your System Administrator can create a custom Callers List XML application allowing you to access the Callers List via an XML Key instead of
the Callers List Key. This allows you to configure the Callers List Key
with other functions if required. Contact your System Administrator for
more information.
Your phone logs the number and name (if available) of the caller, when they last
called, and the number of times they tried to reach you. When the Callers list is full,
the oldest call records are deleted to accommodate the information of new callers.
If the phone number of an incoming or outgoing call matches a number that you have
programmed with a name in a programmable key or in the Directory List, the Callers
List displays the name and number.
The display shows you how many callers have been added to the list since you last
checked it.
104 Model 53i IP Phone User Guide
Caller’s List Screen Display
Display Item
Description
450-349-0438
Indicates you have returned the call from the Callers
list.
N MAR 04 3:30pm 2x
"N" indicates a new call.
XX New Callers
When you’re not on the telephone and not in the
Callers list, the display shows you how many callers
have been added to the list since you last checked it.
Indicates an unanswered call in the Callers list.
Indicates an answered call in the Callers list.
Indicates a Call Waiting call in the Callers list.
Indicates an incoming Call Waiting call.
John Burns
9054550055
Jun 8 2:41pm 2X
"2x" indicates this caller has called twice. The display
shows the date and time of the last call from that caller.
You can view, scroll, and delete line items in the Callers List from the IP phone UI.
You can also directly dial from a displayed line item in the Callers List.
Managing Calls
Model 53i IP Phone User Guide 105
Managing Calls
Accessing the Callers List
IP Phone UI
Use the following procedure to access the Callers List. Use the following illustration
as a reference.
Callers List
Key
Handsfree
Button
1. Press the Callers List Key. Press
Press
and
to see the most recent call, or
2. To dial the displayed number just press
line keys.
3. Press the Callers List Key to cancel.
106 Model 53i IP Phone User Guide
to move through the Callers list.
to see the oldest call on your list.
or lift the Handset or press any
Editing Entries in the Callers List
Important: The Caller List does not save changes. Editing in the Callers List is
generally used if you plan to call the number and need to add a prefix.
In the Callers List, if a dial pad key is pressed when a number and/or a name is
displayed, the cursor automatically adds the digit at the left side of the number to
enable the entry of the prefix.
007
N
John Burns
9054550055
Jun 8 2:55pm
IP Phone UI
Use the following procedure to edit the Callers List. Use the following illustration as
a reference.
Callers List
Key
1. Press the Callers List Key.
2. Press
and
recent call, or
to find the entry you want to edit. Press
to view the most
to see the oldest call on your list.
3. Press any key on the dial pad to begin editing.
4. To move the cursor one digit to the right, press 4. To erase one digit to the left of
the cursor, press 3.
5. To dial the displayed number press
, or just lift the handset, or press any
line keys.
Model 53i IP Phone User Guide 107
Managing Calls
Handsfree
Button
Managing Calls
Deleting Entries From the Callers List
You can delete individual items from the Callers List, or you can delete all items in
the Callers List.
IP Phone UI
Use the following procedure to delete an individual item from the Callers List. Use
the following illustration as a reference.
Delete Key
Callers List
Key
1. Press the Callers List Key.
2. Press
and
to find the item you want to delete.
3. Press the Delete Key.
4. Press the Delete Key again at the prompt to erase the item.
IP Phone UI
Use the following procedure to delete all items from the Callers List.
1. Press the Callers List Key.
2. Press the Delete Key.
3. Press the Delete Key again at the prompt to erase all items.
108 Model 53i IP Phone User Guide
Downloading the Callers List to Your PC
You can download the Callers List to your PC for viewing using the Aastra Web UI.
When you download the Callers List, the phone stores the callerlist.csv file to your
computer in comma-separated value (CSV) format.
You can use any spreadsheet application to open the file for viewing. The following
is an example of a Callers List in a spreadsheet application. This file displays the
name, phone number, and the line that the call came in on.
Download the Callers List
Use the following procedure to download the Callers List to your PC using the Aastra
Web UI.
Aastra Web UI
1. Click on Operation->Directory.
.
3. Click OK.
4. Enter the location on your computer where you want to download the Callers List
and click SAVE.
The callerslist.csv file downloads to your computer.
5. Use a spreadsheet application to open and view the Callers List.
Model 53i IP Phone User Guide 109
Managing Calls
2. In the Callers List field, click on
A File Download message displays.
Managing Calls
Call Forwarding
The call forwarding feature on the IP phone allows incoming calls to be forwarded to
another destination. The phone sends the SIP message to the SIP proxy, which then
forwards the call to the assigned destination.
Call forwarding is disabled by default. You can enable call forwarding on a global
basis or on an individual line-basis, for each line. If you have configured call
forwarding on an individual line, then the settings for this line are used; otherwise,
the phone-wide call forward settings are used.
You can enable call forwarding on all phones (global settings) or on specific lines
(local settings) of a single phone. For local settings, you can set call forwarding on up
to 9 individual lines.
For global and local call forwarding, you can set the following:
• Call forward mode
• Destination number
• Number of rings before forwarding the call (from 1 to 9 rings)
The following are the call forward modes you can set.
Call Forward Mode
Description
Off
(Aastra Web UI only)
Disables call forward
All
Phone forwards all incoming calls
immediately to the specified
destination.
Busy
Phone forwards incoming calls if the
line is already in use.
No Answer
Phone forwards the call if it is not
answered in the specified number of
rings
Busy No Answer
Phone forwards the call if either the
line is already in use or the call is not
answered in the specified number of
rings.
Note: You can set the global call forward settings using the IP phone UI or the
Aastra Web UI. However, you must use the Aastra Web UI to set the perline call forward settings. The per-line settings override the settings for
global call forwarding.
110 Model 53i IP Phone User Guide
Setting Call Forwarding
Use the following procedure to set global call forwarding.
For Global Call Forward Settings
IP Phone UI
1. Press
on the phone to enter the Options List.
2. Select Call Forward and press 4.
3. Select Cfwd Number and press 4.
4. Enter the number destination for which you want your incoming calls to be forwarded and press 4.
Note: If you leave the "Number" field blank, call forwarding is disabled.
5. Press
to scroll to Cfwd Mode and press 4.
6. Use the
and
to select a value and press 4. Valid values are Off, All, Busy,
NoAns (No Answer), BusyNoAns (Busy No Answer).
7. Press
8. Use the
to scroll to No. Rings and press 4.
and
to select a value and press 4. Valid values are 1 to 9.
Note: "Number of Rings" field applies to No Answer and Busy No Answer
modes only.
A message displays "confirmed".
1
CFWD NoAnswer
Sun Jan 2 03:00
Model 53i IP Phone User Guide 111
Managing Calls
The following example shows the idle screen on the IP Phone with Call Forwarding
set to "No Answer" mode.
Managing Calls
Aastra Web UI
1. Click on Basic Settings->Call Forward.
2. In the "Mode" field, select the mode you want to set on your phone.
Note: To disable call forwarding in the Aastra Web UI, set the mode to OFF
and remove the phone number in the "Number" field.
3. In the "Number" field, enter the call forward number for which you want your
calls to be call forwarded.
4. In the "Number of Rings" field, enter the number of rings you want to set before
the call is
forwarded. Valid values are 1 to 9.
5. Click
to save the Call Forward settings. The changes are dynamic and
are immediately applied to the phone.
The following example shows the idle screen on the IP Phone with Call Forwarding
set to "No Answer" mode.
1
CFWD NoAnswer
Sun Jan 2 03:00
112 Model 53i IP Phone User Guide
For Per-Line Call Forward Settings
Aastra Web UI
1. Click on Basic Settings->Call Forward.
2. Select a line to set Call Forwarding on.
3. In the "Mode" field, select the mode you want to set on this line.
Notes:
1.To disable call forwarding in the Aastra Web UI, set the mode to OFF and
remove the phone number in the "Forward Number" field.
2.To force a line to use the global settings, set the "Mode" field to Global.
4. In the "Forward Number" field, enter the call forward number for which you
want your calls on this line to be call forwarded.
6. Click
to save the Call Forward settings. The changes are dynamic and
are immediately applied to the phone.
Model 53i IP Phone User Guide 113
Managing Calls
5. In the "Number of Rings" field, select the number of rings on the line before the
call is forwarded. Valid values are 1 to 9.
Managing Calls
Missed Calls Indicator
The IP phone has a "missed calls" indicator that increments the number of missed
calls to the phone. This feature is accessible from the IP phone UI only.
The number of calls that have not been answered increment on the phone’s idle
screen as "<number> New Calls". As the number of unanswered calls increment,
the phone numbers associated with the calls are stored in the Callers List. The user
can access the Callers List and clear the call from the list. Once the user accesses the
Callers List, the "<number> New Calls" on the idle screen is cleared.
Accessing and Clearing Missed Calls.
IP Phone UI
Use the following procedure to access and clear missed calls from the Callers List.
Once you display the Callers List, the "<number> New Calls" indicator clears. Use
the following illustration as a reference.
Callers List
Key
1. .Press Callers List key on the phone.
2. Use the
keys to scroll through the line items in the Callers List to find
the line items that have the b icon with the receiver ON. These are the missed
calls to the phone.
3. To clear a line item from the Callers List, select the line item you want to delete
and press the Clear softkey.
The line item is deleted from the Callers List.
114 Model 53i IP Phone User Guide
Voicemail
The Voicemail feature on the 53i IP phone allows you to use a line, configured with a
phone number for dialing out, to connect to a voicemail server.
For each assigned Voicemail number, there can be a minimum of 0 or a maximum of
1 Voicemail access phone number.
The Voicemail list displays a list of phone numbers assigned to the53i that have
registered voicemail accounts associated with them.
Note: The Voicemail list does not display the voicemail access number.
The phone displays up to 99 voicemail messages for an account even if the number of
voicemails exceeds the limit.
Registered account numbers/URIs that exceed the length of the screen, either with or
without the voicemail icon and the message count, are truncated with an ellipse
character at the end of the number/URI string.
The end of the Voicemail list displays the number of new voicemail messages (if any
exist).
Contact your System Administrator for lines configured for Voicemail.
Using Voicemail
IP Phone UI
1. Press the key on the phone that your System Administrator set up to access voicemail. After pressing the key, the phone dials to access the voicemail server.
2. Use the
keys to scroll through the line items in the Voicemail list.
3. When you have selected a line item, press the
handsfree key,
Scroll
From a selected item in the Voicemail list, you can also lift the handset (go offhook) to make an outgoing call using the voicemail access phone number.
Model 53i IP Phone User Guide 115
Managing Calls
Right key, or press a line softkey to make an outgoing call using the voicemail
access phone number associated with the line for which the voicemail account is
registered.
Additional Features
Additional Features
This section describes additional features you can use on the 53i phone.
Star Codes
All of the main call handling and extension management features for your system can
be set up as speed dials on programmable keys on your phone. Contact your System
Administrator for more information.
If these have not been set up, you can dial any star code commands on the 53i phone
the same way you would on a regular telephone.
Suppress DTMF Playback
A feature on the IP phones allows you to enable or disable the suppression of DTMF
playback when a number is dialed from the programmable keys.
When suppression of DTMF playback is disabled, and you press a programmable
key, the IP phone dials the stored number and displays each digit as dialed in the
LCD window.
When the suppression of DTMF playback is enabled, the IP phone dials the stored
number and displays the entire number immediately in the LCD window, allowing
the call to be dialed faster.
DTMF playback suppression is disabled by default. Suppressing DTMF playback
can be configured using the Aastra Web UI.
Configuring Suppression of DTMF Playback
Aastra Web UI
Use the following procedure to configure suppression of DTMF playback.
Note: "Suppress DTMF Playback" is disabled by default.
1. Click on Basic Settings->Preferences.
2. Go to the "General" section.
3. Enable the "Suppress DTMF Playback" field by checking the check box. (Disable this field by unchecking the box). Default is disabled.
4. Click
to save your settings.
116 Model 53i IP Phone User Guide
Display DTMF Digits
A feature on the IP phones allows users to enable or disable DTMF (dual-tone multifrequency) digits to display to the IP phone when using the keypad to dial, or when
dialing from a programmable key.
DTMF is the signal sent from the phone to the network that you generate when you
press the phone’s touch keys. This is also known as “touchtone” dialing. Each key
you press on your phone generates two tones of specific frequencies. One tone is
generated from a high-frequency group of tones and the other from a low frequency
group.
If you enable the Display DTMF Digits parameter, the digits you are dialing from the
keypad or from a programmable key display to the IP phone’s LCD display. This
parameter is disabled by default (no digits display when dialing).
You can enable the "Display DTMF Digits" parameter using the Aastra Web UI.
Configuring Display of DTMF Digits
Aastra Web UI
Use the following procedure to configure the display of DTMF digits on the IP
phone.
Note: "Display DTMF Digits" is disabled by default.
1. Click on Basic Settings->Preferences->General.
3. Click
to save your settings.
Model 53i IP Phone User Guide 117
Additional Features
2. Enable the "Display DTMF Digits" field by checking the check box.
Disable this field by unchecking the box). Default is disabled.
Additional Features
Enable/Disable Call Waiting
The call waiting feature notifies the user on an active call, of a new incoming call.
You can disable the call waiting feature, so that the new incoming call is
automatically rejected by the phone with a busy message.
If you disable call waiting on the phone, and the user is on a call, any further
incoming calls receive busy unless “Call Forward Busy” or “Call Forward No
Answer and Busy” is configured on the phone (for information on
"Call Forwarding", see page 110.) It then forwards the call according to the rule
configured. The phone can only:
• transfer the currently active call
or
• accept transferred calls if there is no active calls.
If call waiting is disabled:
• intercom calls are treated as regular incoming calls and are rejected.
• pre-dialing with live dial pad disabled still accepts incoming calls.
• the “Incoming Call Interrupts Dialing” parameter is ignored because the
incoming call is automatically rejected (for information on "Incoming Call
Interrupts Dialing" see page 124).
• the Missed Calls List does not get updated with details of calls.
• the Blind Transfer feature on the phone may not work if two calls are made to
the phone at one time.
You can disable call waiting using the configuration files or the Aastra Web UI.
118 Model 53i IP Phone User Guide
Enabling/Disabling Call Waiting
Aastra Web UI
Use the following procedure to enable or disable Call Waiting on the IP phone.
Note: "Call Waiting" is enabled by default.
1. Click on Basic Settings->Preferences->General.
2. Call Waiting is enabled by default. If required, disable the "Call Waiting" field by
unchecking the check box.
3. Click
to save your settings.
Additional Features
Model 53i IP Phone User Guide 119
Additional Features
Play Call Waiting Tone
You can enable or disable the playing of a call waiting tone when you are on an active
call and a new call comes into the phone.
You can configure this feature using the Aastra Web UI.
Configuring Call Waiting Tone
Aastra Web UI
Use the following procedures to configure a call waiting tone on the IP phone.
Note: "Play Call Waiting Tone" is enabled by default.
1. Click on Basic Settings->Preferences->General.
2. A call waiting tone is enabled by default. If required, disable the "Play Call Waiting Tone" field by unchecking the check box.
3. Click
to save your settings.
120 Model 53i IP Phone User Guide
Stuttered Dial Tone
You can enable or disable the playing of a stuttered dial tone when there is a message
waiting on the IP phone.
You can configure this feature using the Aastra Web UI.
Configuring Stuttered Dial Tone
Aastra Web UI
Use the following procedures to configure stuttered dial tone on the IP phone.
Note: "Stuttered Dial Tone" is enabled by default.
1. Click on Basic Settings->Preferences->General.
3. Click
to save your settings.
Model 53i IP Phone User Guide 121
Additional Features
2. Stuttered dial tone is enabled by default. If required, disable the "Stuttered Dial
Tone" field by unchecking the check box.
Additional Features
XML Beep Support
Using the Aastra Web UI, you can enable or disable a beep to be audible when the
phone receives an XML application using the "XML Beep Support" field at the path
Basic Settings->Preferences->General. If you disable this feature, then no beep is
heard when the XML application arrives to the phone.
If your System Administrator has set a value for this feature in a custom XML
application or in the configuration files, the value you set in the Aastra Web UI
overrides the Administrator’s setting. Setting and saving the value in the Aastra Web
UI applies to the phone immediately.
Configuring XML Beep Support
Aastra Web UI
Use the following procedures to configure an XML beep on the IP phone.
Note: "XML Beep Support" is enabled by default.
1. Click on Basic Settings->Preferences->General.
2. "XML Beep Support" is enabled by default. If required, disable the "XML Beep
Support" field by unchecking the check box.
3. Click
to save your settings.
122 Model 53i IP Phone User Guide
Status Scroll Delay
Using the Aastra Web UI, you can specify a scroll delay option that allows you to set
the time delay, in seconds, between the scrolling of each status message on the phone.
You can specify this setting in the "Status Scroll Delay (seconds)" field at the path
Basic Settings->Preferences->General. The default time is 5 seconds for each
message to display before scrolling to the next message. You can increase or decrease
this time as required. Setting and saving the value in the Aastra Web UI applies to the
phone immediately.
Configuring Status Scroll Delay
Aastra Web UI
Use the following procedures to specify a status scroll delay on the IP phone.
1. Click on Basic Settings->Preferences->General.
3. Click
to save your settings.
Model 53i IP Phone User Guide 123
Additional Features
2. Enter a value in the "Status Scroll Delay (seconds)" field. Valid values are: 1 to
25 seconds. Default is 5.
Additional Features
Incoming Call Interrupts Dialing
If you are dialing a call on your phone and another call comes in while you are
dialing, you can allow the incoming call to interrupt dialing by enabling a parameter
called "Incoming Call Interrupts Dialing". You can enable or disable this
parameter in the Aastra Web UI at the path
Basic Settings->Preferences->General.
When you enable this field in the Aastra Web UI, an incoming call automatically
interrupts the outgoing call during dialing and allows the phone to ring for you to
answer the incoming call.
When you disable this parameter, which is the default, the phone does not interrupt
the outgoing call during dialing and instead rings the incoming call on another free
line (or sends busy signal if all remaining lines are busy). You have a choice to ignore
the incoming call, or answer the incoming call on another line. If you choose to
answer the incoming call, you can answer the call, finish the call, and then hang up.
You can still go back to the original outgoing call and finish dialing out.
Notes:
1. On a 53i, you must use the down arrow key to ignore the call. To answer the
call you must press the line key where the call is coming in.
2. If you disable this field, and the phone receives an incoming call while you
are dialing an outgoing call, you can pick up the call and perform transfer or
conference as required.
Configuring "Incoming Call Interrupts Dialing"
Aastra Web UI
Use the following procedures to configure "Incoming Call Interrupts Dialing" on the
IP Phone.
Note: "Incoming Call Interrupts Dialing" is disabled by default.
1. Click on Basic Settings->Preferences->General.
2. Enable the "Incoming Call Interrupts Dialing" field by checking the check box.
Disable this field by unchecking the box). Default is disabled.
3. Click
to save your settings.
124 Model 53i IP Phone User Guide
Goodbye Key Cancels Incoming Calls
The 53i has a feature that allows you to configure the Goodbye key to drop a second
incoming call or ignore incoming calls presented to the phone when you are on an
active call. The parameter is called "Goodbye Key Cancels Incoming Call" and is
configurable via the Aastra Web UI.
If you enable this parameter, which is the default, pressing the Goodbye key rejects
calls coming into the phone while you are on an active call. When you disable this
parameter, pressing the Goodbye key hangs up the active call.
If you disable this feature, and the phone receives another call when an active call is
already present, the 53i displays "3 Ignore Answer 4" on the LCD. For the 53i,
you must use the Right and Left arrow keys to answer or ignore the call.
A User can set this parameter using only the Aastra Web UI.
Configuring Goodbye Key to Cancel Incoming Calls
Aastra Web UI
Use the following procedure to configure the Goodbye key to cancel incoming calls
on the IP Phone.
Note: "Goodbye Key Cancels Incoming Call" is enabled by default.
1. Click on Basic Settings->Preferences->General.
3. Click
to save your settings.
Model 53i IP Phone User Guide 125
Additional Features
2. The "Goodbye Key Cancels Incoming Call" field is enabled by default. If
required, disable this field by unchecking the check box.
Additional Features
Using the Goodbye Key to Cancel Incoming Calls Feature
IP Phone UI
IF
THEN
"Goodbye Key Cancels Incoming Call" is
enabled AND a second call comes in
while you are on an active call,
press the Goodbye key to reject the
second incoming call.
"Goodbye Key Cancels Incoming Call" is
disabled AND a second call comes in
while you are on an active call,
press the Goodbye key to hang up on
the active call so you can answer the
second incoming call.
"Goodbye Key Cancels Incoming Call" is
disabled AND a second call comes in
while you are on an active call,
press the Left Arrow 3 key to ignore the
second incoming call and remain on the
active call
OR
press the Right Arrow 4 key to answer
the second incoming call.
126 Model 53i IP Phone User Guide
UPnP Mapping Lines (for remote phones)
Universal Plug and Play (UPnP) is a standard that uses Internet protocols to enable
devices to be plugged into a network and automatically know about each other. With
UPnP, when a user plugs a device into the network, the device configures itself,
acquires a TCP IP address, and uses a discovery protocol based on the Internet's
HTTP or HTTPS URL to announce its presence on the network to other devices.
This method of device discovery on a network is called “Universal Plug and Play” or
UPnP. If you enable UPnP, and the phone is discovered on the network, port
mappings are set up between the phone and the Internet Gateway Device (IGD) in
your network. The phone controls the opening, closing, and polling of ports on the
IGD. HTTP and SIP use a single port each. RTP/RTCP uses a range of ports.
You can enable the UPnP mappings to specific lines on your phone. You set this
configuration using the Aastra Web UI at Basic Settings->Preferences->UPnP
Mapping Lines.
Note: UPnP must be enabled on your remote phone before you can configure
the UPnP mapping lines. Contact your System Administrator for more
information.
Configuring UPnP Mapping Lines
Aastra Web UI
Use the following procedure to configure the UPnP mapping lines on the IP phone.
1. Click on Basic Settings->Preferences->General.
3. Click
to save your settings.
Model 53i IP Phone User Guide 127
Additional Features
2. The "UPnP Mapping Lines" field is set to 0 by default. If required, change the
setting to a specific line by selecting a line from the list. Valid values are 0 through
10. The line you select is the line that your remote phone uses to perform Universal Plug and Play on the network you are connecting to.
Additional Features
Message Waiting Indicator
You can configure the Message Waiting Indicator (MWI) to illuminate for a specific
line or for all lines. For example, if you configure the MWI LED on line 3 only, the
LED illuminates if a voice mail is pending on line 3. If you configure the MWI LED
for all lines, the LED illuminates if a voice mail is pending on any line on the phone
(lines 1 through 9).
You configure the MWI indicator using the Aastra Web UI.
Configuring Message Waiting Indicator
Aastra Web UI
Use the following procedure to configure the message waiting indicator on a specific
line or on all lines on the IP phone.
Note: "Message Waiting Indicator Line" parameter is set to ALL lines by
default.
1. Click on Basic Settings->Preferences->General.
2. The "Message Waiting Indicator Line" field is set to ALL lines by default. If
required, change the setting to a specific line by selecting a line from the list. Valid
values are All and lines 1 through 9.
3. Click
to save your settings.
128 Model 53i IP Phone User Guide
Incoming Intercom Call Features
Incoming Intercom
By default, the IP phone allows incoming intercom calls to be automatically
answered without having to set up an Icom key on your phone. The phone
automatically plays a warning tone when it receives an incoming intercom call. It
also mutes the microphone. If the intercom call comes into the phone while an active
call is already present, the phone puts the active call on hold and answers the
intercom call.
You can change the behavior of how the phone handles incoming intercom calls by
enabling/disabling specific parameters using the Aastra Web UI. The following table
describes these features.
Incoming Intercom
Features in
Aastra Web UI
Description
Microphone Mute
Allows you to enable or disable the microphone on the
IP phone for Intercom calls made by the originating
caller.
Auto Answer
Allows you to enable or disable the IP phone to
automatically answer an Intercom call. If auto-answer is
enabled on the IP phone, the phone plays a tone (if
"Play Warning Tone" is enabled) to alert the user
before answering the intercom call. If auto-answer is
disabled, the phone rejects the incoming intercom call
and sends a busy signal to the caller.
Note: Your Administrator can set a time period delay before
the phone automatically answers. Contact your System
Administrator for more information.
Allows you to enable or disable a warning tone to play
when the phone receives an incoming intercom call on
an active line.
Allow Barge In
Allows you to enable or disable how the phone handles
incoming intercom calls while the phone is on an active
call.
Microphone Mute
You can mute or unmute the microphone on the IP phone for intercom calls made by
the originating caller. If you want to mute the intercom call, you enable this feature. If
you want to unmute (or hear the intercom call), you disable this feature.
"Microphone Mute" is enabled by default.
Model 53i IP Phone User Guide 129
Additional Features
Play Warning Tone
Additional Features
Auto-Answer/Play Warning Tone
The auto-answer feature on the IP phone allows you to enable or disable automatic
answering for an Intercom call. If “Auto-Answer” is enabled, the phone
automatically answers an incoming intercom call. If “Play Warning Tone” is also
enabled, the phone plays a tone to alert you before answering the intercom call. If
“Auto-Answer” is disabled, the phone rejects the incoming intercom call and sends a
busy signal to the caller.
"Auto-Answer" and "Play Warning Tone" are enabled by default.
Note: Your Administrator can set a time period delay before the phone automatically answers. Contact your System Administrator for more information.
Allow Barge In
You can configure whether or not the IP phone allows an incoming intercom call to
interrupt an active call. The “Allow Barge In” parameter controls this feature. When
you enable the this parameter, which is the default value, an incoming intercom call
takes precedence over any active call, by placing the active call on hold and
automatically answering the intercom call. When you disable this parameter, and
there is an active call, the phone treats an incoming intercom call like a normal call
and plays the call warning tone. "Allow Barge In" is enabled by default.
Configuring Incoming Intercom Settings
Aastra Web UI
Use the following procedure to configure incoming Intercom settings on the IP
phone.
1. Click on Basic Settings->Preferences->Incoming Intercom Settings.
2. The "Auto-Answer" field is enabled by default. The automatic answering feature
is turned on for the IP phone for answering Intercom calls. To disable this field,
uncheck the box.
130 Model 53i IP Phone User Guide
Note: If the Auto-Answer field is not checked (disabled), the phone rejects the
incoming intercom call and sends a busy signal to the caller.
3. The "Microphone Mute" field is enabled by default. The microphone is muted on
the IP phone for Intercom calls made by the originating caller. To disable this
field, uncheck the box.
4. The "Play Warning Tone" field is enabled by default. If “Auto-Answer” is
enabled, the phone plays a warning tone when it receives in incoming intercom
call. To disable this field, uncheck the box.
5. The "Allow Barge In" field is enabled by default. If “Allow Barge In” is enabled,
the phone puts an active call on hold and answers the incoming Intercom call. To
disable this field, uncheck the box.
6. Click
to save your settings.
Using Redial Key for “Last Number Redial”
The IP phone has an enhanced redial user interface that allows a user to quickly redial
the last number that was dialed out from the phone. You can:
• Press the REDIAL button twice to redial the last number dialed.
• Press the REDIAL button once, scroll the list of numbers, then press the
REDIAL button again to dial the number that displays on the screen.
The “last number redial” feature for the Redial key is static and is not configurable.
Additional Features
Model 53i IP Phone User Guide 131
Available Features Enabled by Administrators
Available Features Enabled by Administrators
There are features on your IP Phone that you can use ONLY if an Administrator has
enabled them on your phone. Those features are described in this section. Contact
your System Administrator for more information.
Outgoing Intercom Calls
If your System Administrator configures the outgoing intercom feature on your
phone, pressing the Icom button allows your phone to find an available line and place
an intercom call to a recipient. To use this feature, you must configure an intercom
key on your phone. For more information about configuring and using an Icom key,
see "Intercom Key" on page 71.
Missed Call Summary Subscription
A feature on the IP phones allows missed calls that have been redirected by the
server, to be incremented in the missed calls indicator on the phone it was initially
directed to. This feature is called the Missed Call Summary Subscription and can
be configured by your System Administrator. For this feature to work, you must
configure voicemail on the phone that the call was initially directed to.
For example, phones A, B, and C are connected to the server. Your Administrator
configures the server to direct calls coming into phone B (which has voicemail
configured) to be forwarded to phone C. When phone A calls phone B, the server
forwards the call to phone C. With the Missed Call Summary Subscription enabled,
phone B receives notification from the server that the call was forwarded and the
missed calls indicator is incremented on phone B. See the illustration below.
3KRQH$
$FDOOV%
3KRQH&
3KRQH%
%IRZDUGVFDOOWR&
0LVVHGFDOOVLQGLFDWRULQFUHPHQWVRQSKRQH%
9RLFHPDLOPXVWEHFRQILJXUHGRQSKRQH%
1RWH
Note: Your System Administrator can configure the Missed Call Summary
Subscription feature on a global or per-line basis.
132 Model 53i IP Phone User Guide
Customizable Callers List Key
Autodial (Hotline and Warmline)
Your System Administrator can configure an autodial feature on your phone. If
autodial is enabled, the phone automatically dials a preconfigured number whenever
it is off-hook. Depending on the configuration specified by your Administrator, the
Autodial functions as either a “hotline”, or as a “warmline,” as follows:
• Hotline: The IP phone immediately dials a preconfigured number when you
lift the handset.
• Warmline: The IP phone waits for a specified amount of time after you lift the
handset before dialing a preconfigured number. If you do not dial a number
within the time allotted, then the IP phone begins to dial the number.
The Autodial feature is available on a global or per-line basis. Contact your System
Administrator for more information.
Notes:
1. Any speeddial numbers that you configure on your IP phone are not
affected by autodial settings.
2. If Autodial is configured on your phone, any lines that function as hotlines
do not accept conference calls, transferred calls, and/or intercom calls.
Centralized Conferencing
The 53i supports centralized conferencing for Sylantro and Broadsoft servers. This
feature provides centralized conferencing on the SIP server (versus localized, on the
phone). Your System Administrator must enable this feature on your phone before
you can use centralized conferencing.
Centralized Conferencing allows you to perform the following:
• Conference two active calls together into a conference call.
• When on an active conference call, invite another party into the call.
• Create simultaneous conference calls on the same IP phone (Sylantro servers
only). For example, a user at extension 2005 could create two conferences,
and put one conference on hold while conversing with the other party:
- Line 1: conference together extensions 2005, 2010, and 2020.
- Line 2: conference together extensions 2005, 2011 and 2021.
• Disconnect from an active conference call while allowing the other callers to
remain connected.
• Add unlimited number of users to a conference (dependent on the limitations
of the server).
• Join two active calls together into a conference.
• Join incoming or outgoing active calls to any existing conference.
Reference
For more information about using Centralized Conferencing, see "Centralized
Conferencing (for Sylantro and Broadsoft Servers)" on page 90.
Model 53i IP Phone User Guide 133
Available Features Enabled by Administrators
Your System Administrator can specify an XML URI that creates a custom Callers
List application for your phone. When you press the Callers List key, the phone
accesses a custom XML URI Callers List instead of the standard Callers List. Contact
your System Administrator for more information.
Available Features Enabled by Administrators
Answer and Ignore Softkeys for XML Applications
If you are accessing XML applications on your phone and a call comes in, your
System Administrator can create "Answer" and "Ignore" keys that you can use to
either answer the incoming call, or ignore it..
!N8-,APPLICATIONCANDISPLAY
HEREWHILEACALLISCOMINGIN
,JQRUH
$QVZHU
When the 3 Ignore Answer 4 line displays, you can press the Right Arrow key
(Answer) to answer the incoming call without disturbing the current XML
application. When you answer the call, the 3 Ignore Answer 4 line disappears from
the LCD. Pressing the Left Arrow key (Ignore) ignores the incoming call without
disturbing the current XML application. Contact your System Administrator for more
information.
XML Softkey for Special Characters in XML Applications
When using XML applications that require you to enter information such as email
addresses, that require special symbols (for example, the "@" symbol), your System
Administrator can create an XML softkey to access these symbols. Pressing the
symbol key in an XML application can display a single symbol or a list of symbols
from which you can choose the symbol you need. Contact your System
Administrator for more information.
“Hold” Feature Enhancement (for Broadsoft Servers)
The Hold feature allows you to put an active call on “hold,” then retrieve the call
later. This enhancement is intended for IP phones operating with servers that support
RFC3264 (for example, Broadsoft). If a server does not support RFC3264, then the
IP phones do not use RFC3264 functionality.
134 Model 53i IP Phone User Guide
Model 536M Expansion Module
The 53i IP Phone offers an optional 536M Expansion Module that attaches to the
right side of the phone to provide additional softkeys.
Model 536M
The softkeys support the following features:
• Busy Lamp Fields (BLFs) (maximum of 50)
• Speedial
• Shared Call Appearance
• Phone Lock
You can configure the softkeys using the Aastra Web UI.
Reference
For more information about configuring the expansion module softkeys with these
functions, see the "Programmable Keys" on page 40.
Model 53i IP Phone User Guide 135
Model 536M Expansion Module
The 536M provides 18 softkeys in each column (totaling 36 keys) on the keypad.
Each key provides an LED for indicating call status. The 536M provides a paper
label for convenient key labeling.
Model 536M Expansion Module
Using the Expansion Module
536M Expansion Module
After configuring the softkeys on the 536M Expansion Module, you can record the
name of the softkey on the paper labels provided with the Expansion Module. Press
the softkey you want to use when applicable.
Softkeys
Lock Phone
BLF Key
Office (speeddial)
References
For more information about configuring softkeys, see "Programmable Keys" on
page 40.
For more information about installing the 536M module on your phone, see the
Aastra 53i IP Phone Installation Guide.
136 Model 53i IP Phone User Guide
Creating a Speeddial Key from the Expansion Module Keypad
IP Phone UI
Pressing and holding down a key on the expansion module initiates a speeddial
feature.
When creating a speeddial key on the Expansion Module, you must select a key that
has no preassigned function (key must be set to none).
1. Press a key on the expansion module for 3 seconds.
A screen displays on the Phone UI with the prompt, "Enter number>".
2. Enter a phone number or extension to assign to that speeddial key using the
phone’s keypad.
The following example illustrates the screen display:
After entering the number, the prompt, "Use Save to end" displays on the screen.
3456
Use Save to end
3. Press Save to save the number as a speeddial key.
By default, the phone automatically assigns the speeddial key to line 1 if available. By default, the phone automatically assigns the speeddial key to line 1 if
available. To select a different line, press the Change softkey and select a different line, or use the phone’s keypad to select a number (1-9), or use the
and
to make your selection.
Line: 1
Change
Use Save to end
4. Press Save to save the speeddial key to the line specified.
Note: Use the Aastra Web UI to edit or delete this speeddial key.
Model 53i IP Phone User Guide 137
Model 536M Expansion Module
Speeddial
Enter number> 3456
Troubleshooting Solutions
Troubleshooting Solutions
Why is my display blank?
Ensure that power is being provided to your phone. Make sure your phone is plugged
into a power source.
Why is my speakerphone not working?
If you press the
button and the speaker light flashes and you do not hear dial
tone through the speaker phone, the Set Audio option in the phone’s Options list has
been set up for headset use. Press
a second time and if the light goes out, the
phone has been set up to be used only with a headset or handset. If the light stays on
steady and you hear dial tone, the phone has been set up so that you can alternate
between the speakerphone and the headset by pressing
. See the section, "Set
Audio" on page 24 for instructions on how to change the Set Audio option.
Why can’t I get a dial tone?
Check for any loose connections and that the phone has been installed properly. For
installation instructions, please refer to the “Installation and Setup” section in the
Aastra 53i Installation Guide provided with your phone.
Why doesn’t my phone ring?
Check the ring volume on your phone. It may be turned down or turned off. To adjust
the ringer volume setting, press the volume button when the phone is on-hook and
idle. For more information, refer to the “Adjusting Volume section” in the Aastra
53i Installation Guide provided with your phone.
Why is the light not coming on with a new Voice Mail Message?
Your phone system or service provider must provide “Visual” Message Waiting
service for this function to work. Check with your System Administrator for more
information.
How do I find the IP address of my phone?
Instructions on where to find the IP address of your phone can be found in this guide
in the section, "Finding Your Phone’s IP Address" on page 18.
138 Model 53i IP Phone User Guide
How do I change my user password?
You can change the user password from the IP phone UI or the Aastra Web UI.
IP Phone UI
1. Press
on the phone to enter the Options List.
2. Select User Password and press 4.
3. Enter the current user password and press 4.
4. Enter the new user password and press 4..
5. Re-enter the new user password and press 4.
A message, "Password Changed" displays on the screen.
Aastra Web UI
1. Click on Operation->User Password.
2. In the "Current Password" field, enter the current user password.
3. In the "New Password" field, enter the new user password.
4. In the "Password Confirm" field, enter the new user password again.
5. Click
to save your changes.
For information on how to access the Aastra Web UI, go to the section "Using the
Aastra Web UI" on page 14.
Why does my phone display "Bad Encrypted Config"?
The IP phone displays "Bad Encrypted Config" because encrypted configuration files
are enabled but the decryption process has failed.
Report this error to your System Administrator.
Model 53i IP Phone User Guide 139
Troubleshooting Solutions
Note: By default, the user name is “user” (all lowercase) and the password
field is left blank. If you have forgotten your password, contact your
System Administrator for assistance.
Troubleshooting Solutions
How do I restart the IP phone?
IP Phone UI
1. Press the
button on the phone to enter the Option List.
2. Use the
key to scroll down the list of options to Phone Status and press the
4. key to select.
3. Press the
key to scroll to the Restart Phone option.
Press the 4. key to confirm and restart the phone. If you do not wish to restart your
phone, press the 3 key to cancel.
Note: Your phone is out of service temporarily during the restart and downloading process.
Aastra Web UI
1. Click on Operation->Reset.
2. Click
.
3. Click OK at the confirmation prompt.
140 Model 53i IP Phone User Guide
How do I lock my phone?
You can lock your phone to prevent the phone from being used or configured. You
can lock the phone using any of the following:
• At the path Options->Phone Lock on the IP Phone UI.
• At the path Operations->Phone Lock on the Aastra Web UI.
• At a configured key on the phone. For more information about configuring a
Lock/Unlock key on your phone, see "Phone Lock Key" on page 74.
Use the following procedure to lock an IP phone using the IP Phone UI.
IP Phone UI
Lock the Phone
1. Press
on the phone to enter the Options List.
2. Select Phone Lock and press 4.
3. Press 4 to set the phone to lock.
Unlock the Phone
1. Press
on the phone to enter the Options List.
2. Enter your user password and press 4.
The phone unlocks.
Use the following procedure to lock an IP Phone using the Aastra Web UI.
Aastra Web UI
1. Click on Operation->Phone Lock.
Lock the Phone
2. In the "Lock the Phone?" field, click
.
The phone locks dynamically and displays the following message:
"Phone is locked".
Model 53i IP Phone User Guide 141
Troubleshooting Solutions
4. Press
on the phone.
The following message displays:
"Phone is locked".
Troubleshooting Solutions
Unlock the Phone
3. Click on Operation->Phone Lock.
4. In the "Unlock the Phone?" field, click
.
The phone unlocks dynamically and displays the following message:
"Phone is unlocked".
142 Model 53i IP Phone User Guide
Limited Warranty
Aastra Telecom warrants this product against defects and malfunctions during a one (1) year
period from the date of original purchase. If there is a defect or malfunction, Aastra Telecom
shall, at its option, and as the exclusive remedy, either repair or replace the telephone set at no
charge, if returned within the warranty period.
If replacement parts are used in making repairs, these parts may be refurbished, or may contain
refurbished materials. If it is necessary to replace the telephone set, it may be replaced with a
refurbished telephone of the same design and color. If it should become necessary to repair or
replace a defective or malfunctioning telephone set under this warranty, the provisions of this
warranty shall apply to the repaired or replaced telephone set until the expiration of ninety (90)
days from the date of pick up, or the date of shipment to you, of the repaired or replacement set,
or until the end of the original warranty period, whichever is later. Proof of the original
purchase date is to be provided with all telephone sets returned for warranty repairs.
Exclusions
Aastra Telecom does not warrant its telephone sets to be compatible with the equipment of any
particular telephone company. This warranty does not extend to damage to products resulting
from improper installation or operation, alteration, accident, neglect, abuse, misuse, fire or
natural causes such as storms or floods, after the telephone is in your possession.
Aastra Telecom shall not be liable for any incidental or consequential damages, including, but
not limited to, loss, damage or expense directly or indirectly arising from the customers use of
or inability to use this telephone, either separately or in combination with other equipment.
This paragraph, however, shall not apply to consequential damages for injury to the person in
the case of telephones used or bought for use primarily for personal, family or household
purposes.
This warranty sets forth the entire liability and obligations of Aastra Telecom with respect to
breach of warranty, and the warranties set forth or limited herein are the sole warranties and are
in lieu of all other warranties, expressed or implied, including warranties or fitness for
particular purpose and merchantability.
Warranty Repair Services
After Warranty Service
Aastra Telecom offers ongoing repair and support for this product. This service provides repair
or replacement of your Aastra Telecom product, at Aastra Telecom's option, for a fixed charge.
You are responsible for all shipping charges. For further information and shipping instructions;
In North America, contact our service information number: 1-800-574-1611.
Outside h America, contact your sales representative.
Note: Repairs to this product may be made only by the manufacturer and its
authorized agents, or by others who are legally authorized. This restriction applies during and after the warranty period. Unauthorized repair
will void the warranty.
Model 53i IP Phone User Guide
143
Limited Warranty
Should the set fail during the warranty period;
In North America, please call 1-800-574-1611 for further information.
Outside North America, contact your sales representative for return instructions.
You will be responsible for shipping charges, if any. When you return this telephone for
warranty service, you must present proof of purchase.
Appendix A - Time Zone Codes
The following table identifies the time zone name and time zone code to use on the IP
phone.
Time Zone Name/Time Zone Code Table
Time Zone Code
AD-Andorra
AG-Antigua
AI-Anguilla
AL-Tirane
AN-Curacao
AR-Buenos Aires
AS-Pago Pago
AT-Vienna
AU-Lord Howe
AU-Tasmania
AU-Melbourne
AU-Sydney
AU-Broken Hill
AU-Brisbane
AU-Lindeman
AU-Adelaide
AU-Darwin
AU-Perth
AW-Aruba
CET
AST
AST
CET
AST
ART
BST
CET
LHS
EST
EST
EST
CST
EST
EST
CST
CST
WST
AST
BA-Sarajevo
BB-Barbados
BE-Brussels
BG-Sofia
BM-Bermuda
BO-La Paz
BR-Noronha
BR-Belem
BR-Fortaleza
BR-Recife
BR-Araguaina
BR-Maceio
BR-Sao Paulo
BR-Cuiaba
BR-Porto Velho
BR-Boa Vista
BR-Manaus
BR-Eirunepe
BR-Rio Branco
BS-Nassau
BY-Minsk
BZ-Belize
EET
AST
CET
EET
AST
BOT
FNT
BRT
BRT
BRT
BRS
BRT
BRS
AMS
AMT
AMT
AMT
ACT
ACT
EST
EET
CST
Model 53i IP Phone User Guide
Appendix A - Time Zone Codes
Time Zone Name
A-1
Appendix A - Time Zone Codes
Time Zone Name
Time Zone Code
CA-Newfoundland
CA-Atlantic
CA-Eastern
CA-Saskatchewan
CA-Central
CA-Mountain
CA-Pacific
CA-Yukon
CH-Zurich
CK-Rarotonga
CL-Santiago
CL-Easter
CN-China
CO-Bogota
CR-Costa Rica
CU-Havana
CY-Nicosia
CZ-Prague
NST
AST
EST
EST
CST
MST
PST
PST
CET
CKS
CLS
EAS
CST
COS
CST
CST
EES
CET
DE-Berlin
DK-Copenhagen
DM-Dominica
DO-Santo Domingo
CET
CET
AST
AST
EE-Tallinn
ES-Madrid
ES-Canary
EET
CET
WET
FI-Helsinki
FJ-Fiji
FK-Stanley
FO-Faeroe
FR-Paris
EET
NZT
FKS
WET
CET
GB-London
GB-Belfast
GD-Grenada
GF-Cayenne
GI-Gibraltar
GP-Guadeloupe
GR-Athens
GS-South Georgia
GT-Guatemala
GU-Guam
GY-Guyana
GMT
GMT
AST
GFT
CET
AST
EET
GST
CST
CST
GYT
HK-Hong Kong
HN-Tegucigalpa
HR-Zagreb
HT-Port-au-Prince
HU-Budapest
HKS
CST
CET
EST
CET
IE-Dublin
IS-Reykjavik
IT-Rome
GMT
GMT
CET
A-2 Model 53i IP Phone User Guide
Time Zone Code
JM-Jamaica
JP-Tokyo
EST
JST
KY-Cayman
EST
LC-St Lucia
LI-Vaduz
LT-Vilnius
LU-Luxembourg
LV-Riga
AST
CET
EET
CET
EET
MC-Monaco
MD-Chisinau
MK-Skopje
MQ-Martinique
MS-Montserrat
MT-Malta
MX-Mexico City
MX-Cancun
MX-Merida
MX-Monterrey
MX-Mazatlan
MX-Chihuahua
MX-Hermosillo
MX-Tijuana
CET
EET
CET
AST
AST
CET
CST
CST
CST
CST
MST
MST
MST
PST
NI-Managua
NL-Amsterdam
NO-Oslo
NR-Nauru
NU-Niue
NZ-Auckland
NZ-Chatham
CST
CET
CET
NRT
NUT
NZS
CHA
PA-Panama
PE-Lima
PL-Warsaw
PR-Puerto Rico
PT-Lisbon
PT-Madeira
PT-Azores
PY-Asuncion
EST
PES
CET
AST
WET
WET
AZO
PYS
Model 53i IP Phone User Guide
Appendix A - Time Zone Codes
Time Zone Name
A-3
Appendix A - Time Zone Codes
Time Zone Name
Time Zone Code
RO-Bucharest
RU-Kaliningrad
RU-Moscow
RU-Samara
RU-Yekaterinburg
RU-Omsk
RU-Novosibirsk
RU-Krasnoyarsk
RU-Irkutsk
RU-Yakutsk
RU-Vladivostok
RU-Sakhalin
RU-Magadan
RU-Kamchatka
RU-Anadyr
EET
EET
MSK
SAM
YEK
OMS
NOV
KRA
IRK
YAK
VLA
SAK
MAG
PET
ANA
SE-Stockholm
SG-Singapore
SI-Ljubljana
SK-Bratislava
SM-San Marino
SR-Paramaribo
SV-El Salvador
CET
SGT
CET
CET
CET
SRT
CST
TR-Istanbul
TT-Port of Spain
TW-Taipei
EET
AST
CST
UA-Kiev
US-Eastern
US-Central
US-Mountain
US-Pacific
US-Alaska
US-Aleutian
US-Hawaii
UY-Montevideo
EET
EST
CST
MST
PST
AKS
HAS
HST
UYS
VA-Vatican
CET
YU-Belgrade
CET
A-4 Model 53i IP Phone User Guide
Index
Numerics
536M 135
53i
star codes for 116
A
Aastra Web UI
Basic Settings parameters 17
Operaton parameters 16
phone status 16
about this guide 1
allow barge-in, for intercom 130
audio, setting 24
auto-answer, for intercom 130
autodial (hotline and warmline) 133
B
directory key, softkey for 67
Directory List
downloading to phone 103
directory list 94
downloading to PC 103
sorting 95
do not disturb (DND) 48
documentation 1
DTMF, suppressing playback 116
E
emergency dial plan, defining 37
empty key, softkey for 73
expansion module, 536M 135
expansion module, 560M 135
F
BLF list 50, 52
BLF, setting 49
features, 53i 2
Flash key 52
C
G
call forwarding 110
configuring 111
call waiting tone 120
callers list 104
downloading to phone 109
callers list key, customizable 133
callers list, softkey for 68
calls, ending 93
calls, handling 84
calls, making 77
calls, managing 94
calls, placing on hold 84
calls, receiving 83
calls, transferring 85
conference calls 87
conference key, setting 69, 70
conferencing, centralized 133
contrast level 23
D
H
headset mode 24
headset, using 79
headset/speaker mode 24
hold, feature enhancement using 134
I
idle screens 6
ignore sofkey 134
incoming call interrupts dialing 124
incomplete configuration 7
installation and setup, 9122i 3
intercom calls
incoming call features 129
intercom, outgoing calls using 132
Introduction 143
IP address of the phone 18
IP address, finding 18
Model 55i IP Phone User Guide
Index-1
Index
delete key 10
dial plan, emergency 37
dial tones, stuttered 121
dialing a number 77
dialpad, live 23
getting started 4
Goodbye key cancels incoming call 125
configuring 125
using 126
Index
Index
K
R
keys
as Callers List Key 68
as conference key 70
as Directory key 67
as empty key 73
as Last Call Return 66
as transfer key 69
L
language
overview 29
specifying on IP phone 29
last call return, softkeys for 66
line, setting on programmable key 42
lines settings 39
lock/unlock the phone 141
locking/unlocking the phone 35
via a programmable key 71, 74
M
message waiting indicator,
configuring 128
microphone mute, for intercom 129
microphone volume, headset 25
missed call summary subscription 132
missed calls indicator
accessing and clearing 114
overview 114
N
no service 7
O
options, setting 11
P
park/pickup
using on the IP phone 65
password, resetting user’s 33
phone status 31
plugging in the phone 4
programmable key
deleting 76
description 40
Index-2
redial 80
requirements, 53i 2
restarting the phone 34
ring tone sets 21
ring tones 20
S
save key 10
softkeys
Answer softkey for XML 134
Ignore softkey for XML 134
special characters key
for XML 134
speaker mode 24
speaker/headset mode 24
speakerphone, using 78
speeddial
prefix for 43
setting 43
speeddial key, creating from phone
keypad 43
sprecode softkey 62
star codes 116
starting up the phone 4
status scroll delay 123
T
troubleshooting solutions 138
changing password 139
display blank 138
finding IP address 138
locking/unlocking phone 141
no dial tone 138
no light for VM message 138
no ring 138
no speakerphone 138
phone displays "Bad Encrypted
Config"? 139
restarting phone 140
U
UPnP mapping lines 127
user password 31
using the 53i 8
Model 55i IP Phone User Guide
Index
Index
V
voicemail 83, 115
W
warning tone, for Intercom 130
warranty, limited 143
X
XML application title 60
XML application URI 60
XML beep support 122
XML key, setting 60
XML service, accessing 61
Index-3
Model 55i IP Phone User Guide
If you’ve read this owner’s manual and consulted the Troubleshooting section and
still have problems, please visit our website at www.aastra.com or call 1-800-574-1611
for technical assistance.
© Aastra Telecom Inc.2007 41-001199-00 Rev 01