Belshaw Brothers EZ24 Operator`s manual

EZ Melt Fill & Filter
EZ18, EZ24 & EZ34
Operator’s Manual
Belshaw Bros., Inc.
814 44Tth Street NW, Suite 103
Auburn, WA 98001 USA
Phone: (206) 322-5474 • Fax: (206) 322-5425
Email: service@belshaw.com • http://www.belshaw.com
If you accept the machine from the shipping
company, you are, in effect, saying that the
machine is in good condition, and you must
pay for the machine. Belshaw cannot pay for
shipping damage, because the freight company
has accepted the machine from Belshaw in good
condition, and is responsible for its safe delivery.
For your protection, inspect the machine to see
that no parts are bent, scratched, or otherwise
damaged. If any damage has occurred in
shipping, file a freight claim with the shipping
company immediately.
EQUIPMENT RECORD
Please provide the information below when you correspond with us about your machine.
Purchased by _____________________________________________________________________
Installed by ______________________________________________________________________
Date of Installation ________________________________________________________________
Model number ___________________________________________________________________
Serial number
071312
MN-1317EN
Belshaw Bros., Inc.
814 44Tth ST NW Suite 103
Auburn, WA 98001 USA
Phone: (206) 322-5474 • Fax: (206) 322-5425
Email: service@belshaw.com • http://www.belshaw.com
Contents
1
Operation
1
Melting and Filling
Filtering
2
5
7
Cleaning
10
Belshaw Bros., Inc. • www.belshaw.com • Phone 206-322-5474 • Fax 206-322-5425
EZ18, EZ24, EZ34 OM
MN-1317EN
iii
Preface
The EZ Melt, Fill and Filter models EZ18, EZ24,
and EZ34 are designed to be used with Belshaw
fryers. It performs four functions:
•
It melts shortening
•
It holds shortening
•
It supplies shortening to the fryer kettle
•
It filters used shortening for re-use
floor, possibly causing slips, falls, injury,
burns, or even death.
•
Hot shortening can cause serious burns.
Make sure that proper protective gear
(face shield, gloves and apron) are worn
before filtering, disassembly and
cleaning.
•
Make sure the nozzle of the supply hose
is securely mounted on the side of the
fryer before turning on the pump. If you
do not, hot shortening could spray you,
resulting in serious burns. Also,
shortening could get on the floor,
possibly causing slips, falls, injury,
burns, or even death.
•
Make sure that the system and the
shortening are cool before attempting
any adjustments or repairs. If you do
not, you may be burned.
•
Be careful never to get shortening,
water, or other materials on the floor. If
anything does get spilled on the floor,
mop it up immediately. If you do not,
someone could slip or fall, be burned or
injured, or even die.
•
To avoid damaging the EZ Melt, never
use force to assemble, disassemble,
operate, clean, or maintain it.
•
To avoid electrocution, make sure that
the power cord is not frayed or cracked
and that it does not pass through any
water or shortening.
•
Make sure that the power cord is routed
so that no one will trip over it.
It is not designed to perform any other functions.
The EZ Melt, Fill and Filter uses electrical
elements to melt shortening.
The EZ Melt moves around on casters. It is
meant to be used on the floor. The operator of
the EZ Melt is expected to behave safely and to
read this manual and follow its instructions and
warnings.
Study the instructions and warnings in this
manual carefully. A thorough understanding of
how to install, maintain, and safely operate the
EZ Melt, Fill and Filter will prevent production
delays and injuries.
To use the EZ Melt safely, heed the following
warnings and all other warnings that appear in
this manual:
•
Make sure all hose connections are tight.
If you do not, you may be sprayed with
hot shortening. This could result in
serious burns.
•
Make sure no water gets into the
shortening. Water causes hot shortening
to spatter, which could cause serious
burns.
•
Make sure the EZ Melt kettle has enough
room in it before draining shortening
from the fryer. If you do not, shortening
may overflow the kettle and get on the
Belshaw Bros., Inc. • www.belshaw.com • Phone 206-322-5474 • Fax 206-322-5425
iv
MN-1317EN
EZ18, EZ24, EZ34 OM
1
Operation
To help familiarize you with the major parts of
your EZ Melt model EZ18, EZ24, or EZ34, please study the
photographs below.
handle
heater head
filter assembly
kettle
casters
foot pedal
Figure 1-1. Front View.
Belshaw Bros., Inc. • www.belshaw.com • Phone 206-322-5474 • Fax 206-322-5425
EZ18, EZ24, EZ34 OM
MN-1317EN
1
hose connector
filter assembly
heater head
power cord
kettle
frame with
casters
cube melter
foot pedal
Figure 1-2. Side View.
heating
element
kettle
hose connector
supply hose
Figure 1-3. Top View, Heater Head.
Belshaw Bros., Inc. • www.belshaw.com • Phone 206-322-5474 • Fax 206-322-5425
2
MN-1317EN
EZ18, EZ24, EZ34 OM
Reset
button
Pump switch with
pilot light
Heat
switch
with pilot
light
Figure 1-4. Heater head
Bleeder
Pickup tube
Heating
element
kettle
Figure 1-5. Elements and kettle.
Belshaw Bros., Inc. • www.belshaw.com • Phone 206-322-5474 • Fax 206-322-5425
EZ18, EZ24, EZ34 OM
MN-1317EN
3
Thoroughly clean your EZ Melt before using it.
Refer to Section 2, “Cleaning,” for cleaning
instructions.
WARNING
Moisture causes hot shortening to spatter,
which may cause serious injury. Thoroughly
dry the kettle and any other parts you wash.
WARNING
To avoid electrocuting yourself or damaging
the EZ Melt, never allow water, steam,
cleaning solution, or other liquid to enter the
heater head.
Make sure that the power requirements of the EZ
Melt, shown on the data plate, match your power
source.
Belshaw Bros., Inc. • www.belshaw.com • Phone 206-322-5474 • Fax 206-322-5425
4
MN-1317EN
EZ18, EZ24, EZ34 OM
Melting and Filling
1.
Completely cover the heating element with
shortening. There are two ways to do this:
•
Pre-melt some shortening in a pan on the
stove and pour it into the kettle to cover
the element.
•
Pack solid shortening tightly around the
heating element and bulbs. Do not leave
any air spaces. Cover the heating element
at least 2”/5 cm. (See Figure 1-6)
Figure 1-7. Cube Melter
WARNING
Air spaces can cause the shortening to
overheat and catch on fire.
2.
Install the cube melter in the kettle, opposite
the heater head. Push the cube melter through
the shortening so its legs rest on the bottom
of the kettle. (See Figures 1-7 & 1-8.)
Figure 1-8. Installing the Cube Melter.
3.
Position the EZ Melt near the fryer.
4.
Install the supply hose. Follow these steps:
a. Attach the hose to the pump outlet by
hand-tightening the hose connector.
Figure 1-6. Packing Solid Shortening in the
Kettle.
b. Mount the nozzle of the hose on the edge
of the fryer kettle with the opening
inside the kettle.
Belshaw Bros., Inc. • www.belshaw.com • Phone 206-322-5474 • Fax 206-322-5425
EZ18, EZ24, EZ34 OM
MN-1317EN
5
5.
Make sure that the HEAT and PUMP
switches are in the OFF position. Connect
the EZ Melt to the power source.
To avoid damaging the heating element, make
sure it is completely covered with shortening
before you turn the heater on.
6.
Turn the machine on using the HEAT
switch. When the heat is on, the heating
element melts shortening at 200°F/93°C.
The heat must also be on to operate the
pump.
7.
Turn the pump on using the PUMP switch.
8.
When you want to supply shortening to the
fryer, press the foot pedal.
WARNING
To avoid burning yourself, never touch the
nozzle while the machine is in use.
9.
SIDE OF
CUBE
MELTER
IF SHORTENING
LEVEL IS HERE
OR BELOW ADD
ONE CUBE OF
SHORTENING.
BOTTOM OF
KETTLE
Figure 1-9A. (EZ34 ONLY) When to Add a
Cube of Shortening.
To add a cube of shortening, follow these steps:
1. Position the filter assembly so you can
add shortening. The edge of the kettle
has one or two sets of holes in it. Use
the set of holes that is nearer to the
heater head. When two of the filter
frame’s pins rest in these holes, the filter
assembly hangs vertically. (See Figure
1-10.)
When the fryer has enough shortening in it,
release the foot pedal.
10. As needed, add shortening to the kettle, one
cube at a time. Always add a cube if the
shortening level drops to the tops of the legs
of the cube melter. (See Figure 1-9 & 1-9A.)
SIDE OF
CUBE
MELTER
IF
SHORTENING
LEVEL IS
HERE OR
BELOW ADD
ONE CUBE OF
SHORTENING
BOTTOM OF
KETTLE
Figure 1-9. When to Add a Cube of
Shortening.
Figure 1-10. Positioning the Filter Frame for
Melting.
b. Place a solid cube of shortening on the
cube melter. Let one cube melt and be
pumped out before adding another cube.
Do not overload the EZ Melt.
Belshaw Bros., Inc. • www.belshaw.com • Phone 206-322-5474 • Fax 206-322-5425
6
MN-1317EN
EZ18, EZ24, EZ34 OM
WARNING
Be careful with hot shortening. Always wear
proper protective gear (face shield, apron and
gloves) when filtering, disassembling and
cleaning
Filtering
1. Turn the fryer off. Allow the shortening
to cool to 250°F/121°C. Because hot
shortening is dangerous, FILTER
SHORTENING AT THE LOWEST
TEMPERATURE THAT WORKS. Hot
shortening may also trip the pump motor.
WARNING
Maximum filtering temperature is
325°F/163°C
WARNING
Hot shortening may cause serious injury.
2.
Turn the EZ Melt off. Make sure that both
the HEAT and PUMP switches are in the
OFF position.
If
shortening
level is here
or below
drain fryer.
Side of
cube
melter.
Bottom of
kettle.
Figure 1-11A. (EZ-34 ONLY) When to Drain
the Fryer.
WARNING
When you begin to drain the fryer, the
shortening in the EZ Melt must be shallow
enough for the top of the cube melter to be
exposed. If the shortening is deeper it might
overflow when you drain the fryer, thus
causing burns or other serious injury.
4. Position the shortening filter assembly on
the EZ Melt kettle. The edge of the kettle
has one or two sets of holes in it. Use the
set of holes that is farther from the heater
head. When two of the filter frame’s pins
rest in these holes, the filter assembly
rests horizontally on the end of the kettle.
(See Figure 1-12.)
3. Make sure that the top of the cube melter
is exposed.
Side of
Cube
Melter.
Bottom of
kettle.
If
shortening
level is
here or
below
drain fryer.
Figure 1-11. When to Drain the Fryer.
Figure 1-12. Positioning the Filter Assembly
for Filtering.
Belshaw Bros., Inc. • www.belshaw.com • Phone 206-322-5474 • Fax 206-322-5425
EZ18, EZ24, EZ34 OM
MN-1317EN
7
5.
6.
Disconnect the supply hose from the hose
connector. Hold the two ends of the hose up
so shortening does not drip out. Hang hose
vertically over a pan so the shortening will
drip into the pan.
Attach the rinsing hose securely to the hose
connector. (See Figure 1-13.)
WARNING
To avoid burning yourself, never hold or
touch the metal portion of the nozzle while
the machine is in use. Wear protective
gloves.
WARNING
Thoroughly clean and dry the floor if
shortening, water, or other materials are
spilled. Materials spilled on the floor may
cause serious injury and loss of life.
11. After you have rinsed all the loose particles
out of the fryer kettle, release the foot pedal.
12. After the shortening has drained out of the
fryer kettle and through the EZ Melt filter,
close the drain valve.
13. Turn the EZ Melt off. Make sure that both
the HEAT and PUMP switches are in the
OFF position.
Figure 1-13. Rinsing Hose.
7.
Position the EZ Melt so the filter is directly
under the drain in the fryer kettle.
8.
Reach under the table and slowly open the
fryer’s drain valve.
9.
Move the HEAT and PUMP switches of the
EZ Melt to the ON position.
10. Hold the insulated handle of the hose.
Direct the nozzle into the fryer kettle. Press
the foot pedal and rinse the kettle with
shortening. Do not let shortening splash out
of the kettle!
14. Disconnect the rinsing hose assembly. Hold
the two ends of the hose up so shortening
does not drip out. Hang the hose vertically
over a pan so shortening will drip into the
pan.
15. Bring the supply hose back to the EZ Melt,
holding the two ends of the hose up so
shortening does not drip out.
16. Securely attach the supply hose to the hose
connector. Make sure the outlet nozzle is
securely mounted to the fryer, with the
opening inside the kettle.
17. Move the HEAT and PUMP switches to the
ON position. Press the foot pedal to supply
filtered shortening to the fryer.
18. Before you filter shortening again, empty the
EZ Melt filter. Follow these steps:
Belshaw Bros., Inc. • www.belshaw.com • Phone 206-322-5474 • Fax 206-322-5425
8
MN-1317EN
EZ18, EZ24, EZ34 OM
a. Allow the filter assembly to cool to the
touch.
b. Lift off the filter assembly, holding it by
the frame.
c. Invert the filter assembly over a sink or
garbage can and shake the sediment off
of it. DO NOT rinse the filter.
WARNING
Rinsing the filter could cause water to drop
into the kettle. Hot shortening could spatter
and cause serious injury.
d. Put the filter assembly back on the EZ
Melt.
To order replacement filters for your EZ Melt,
call Belshaw.
Belshaw Bros., Inc. • www.belshaw.com • Phone 206-322-5474 • Fax 206-322-5425
EZ18, EZ24, EZ34 OM
MN-1317EN
9
2
Cleaning
8. Clean the EZ Melt filter. Follow these
steps:
Daily
WARNING
Be careful with hot shortening. Always wear
proper protective gear (face shield, apron and
gloves) when filtering, disassembling and
cleaning
Clean the EZ Melt after every use. Follow these
steps:
1. Turn on the heat and the pump.
2. Press the foot pedal to pump shortening out
of the EZ Melt and into a metal container or
fryer kettle.
3. When you cannot pump any more
shortening out of the EZ Melt, release the
foot pedal. Turn off the heat and the pump.
4. Disconnect the EZ Melt from the power
source.
5. Disconnect the filter hose assembly while
still hot and drain any remaining shortening
back into the filter kettle to prevent
shortening from hardening in the hose.
6. Store the hose hanging vertically with the
lower end of the hose in a metal container to
catch any shortening that may drip.
7. Allow the shortening in the EZ Melt kettle
to cool to 115°F/46°C.
a. Allow the filter assembly to cool to the
touch.
b. Lift off the filter assembly, holding it by
the frame.
c. Invert the filter assembly over a sink or
garbage can and shake the sediment off
of it.
d. Unsnap the filter to remove it from the
filter frame.
e. Rinse the remaining shortening and
crumbs off of the filter.
WARNING
Thoroughly clean and dry the floor if
shortening, water, or other materials are
spilled. Materials spilled on the floor may
cause serious injury and loss of life.
As Needed
1. Remove the cube melter.
2. Loosen the two fasteners at the back of the
heater head, lift it off the kettle and place it
in a clean safe place. The foot valve and
cord will unsnap from the frame. See Figure
2-1.
WARNING
Hot shortening can cause serious injury.
Belshaw Bros., Inc. • www.belshaw.com • Phone 206-322-5474 • Fax 206-322-5425
10
MN-1317EN
EZ18, EZ24, EZ34 OM
6. Wash the kettle, the cube melter, and the
filter frame with warm, soapy water.
7. Dry all the parts completely. The kettle and
all other parts must be completely dry before
you use the EZ Melt again.
WARNING
Failure to dry the kettle and all parts of the EZ
Melt completely may cause shortening to
spatter or erupt. Shortening will overflow the
EZ Melt and may result in fire, injury, or
death.
8. Re-assemble the EZ Melt.
Figure 2-1. Removing the Heater Head.
(Place heater head as shown above so no
damage is done to the element.)
WARNING
Do not touch the heating element! It is very
hot and will burn you.
3. Remove the kettle from the frame. You
must remove it from the rear.
4. Pour any shortening remaining in the kettle
into a metal container. If it is too heavy or
awkward for you to lift by yourself, get
someone to help you.
WARNING
Thoroughly clean and dry the floor if
shortening, water, or other materials are
spilled. Materials spilled on the floor may
cause serious injury and loss of life.
5. Scrape out any residue and discard it.
Belshaw Bros., Inc. • www.belshaw.com • Phone 206-322-5474 • Fax 206-322-5425
EZ18, EZ24, EZ34 OM
MN-1317EN
11
EZ Melt Fill & Filter
EZ18, EZ24 & EZ34
Technical Supplement
Belshaw Bros., Inc.
814 44Tth Street NW, Suite 103
Auburn, WA 98001 USA
Phone: (206) 322-5474 • Fax: (206) 322-5425
Email: service@belshaw.com • http://www.belshaw.com
If you accept the machine from the shipping
company, you are, in effect, saying that the
machine is in good condition, and you must
pay for the machine. Belshaw cannot pay for
shipping damage, because the freight company
has accepted the machine from Belshaw in good
condition, and is responsible for its safe delivery.
For your protection, inspect the machine to see
that no parts are bent, scratched, or otherwise
damaged. If any damage has occurred in
shipping, file a freight claim with the shipping
company immediately.
EQUIPMENT RECORD
Please provide the information below when you correspond with us about your machine.
Purchased by _____________________________________________________________________
Installed by ______________________________________________________________________
Date of Installation ________________________________________________________________
Model number ___________________________________________________________________
Serial number
021810
MN-1318EN
Belshaw Bros., Inc.
814 44Tth Street NW, Suite 103
Auburn, WA 98001 USA
Phone: (206) 322-5474 • Fax: (206) 322-5425
Email: service@belshaw.com • http://www.belshaw.com
Contents
1
Installation
1
2
Troubleshooting
5
3
Appendix
7
Belshaw Bros., Inc. • www.belshaw.com • Phone 206-322-5474 • Fax 206-322-5425
EZ18, EZ24, EZ34 TS
MN-1318EN
iii
Preface
The EZ Melt, Fill and Filter models EZ18, EZ24,
and EZ34 are designed to be used with Belshaw
fryers. It performs four functions:
•
It melts shortening
•
It holds shortening
•
It supplies shortening to the fryer kettle
•
It filters used shortening for re-use
floor, possibly causing slips, falls, injury,
burns, or even death.
•
Hot shortening can cause serious burns.
Make sure that proper protective gear
(face shield, gloves and apron) are worn
before filtering, disassembly and
cleaning.
•
Make sure the nozzle of the supply hose
is securely mounted on the side of the
fryer before turning on the pump. If you
do not, hot shortening could spray you,
resulting in serious burns. Also,
shortening could get on the floor,
possibly causing slips, falls, injury,
burns, or even death.
•
Make sure that the system and the
shortening are cool before attempting
any adjustments or repairs. If you do
not, you may be burned.
•
Be careful never to get shortening,
water, or other materials on the floor. If
anything does get spilled on the floor,
mop it up immediately. If you do not,
someone could slip or fall, be burned or
injured, or even die.
•
To avoid damaging the EZ Melt, never
use force to assemble, disassemble,
operate, clean, or maintain it.
•
To avoid electrocution, make sure that
the power cord is not frayed or cracked
and that it does not pass through any
water or shortening.
•
Make sure that the power cord is routed
so that no one will trip over it.
It is not designed to perform any other functions.
The EZ Melt, Fill and Filter uses electrical
elements to melt shortening.
The EZ Melt moves around on casters. It is
meant to be used on the floor. The operator of
the EZ Melt is expected to behave safely and to
read this manual and follow its instructions and
warnings.
Study the instructions and warnings in this
manual carefully. A thorough understanding of
how to install, maintain, and safely operate the
EZ Melt, Fill and Filter will prevent production
delays and injuries.
To use the EZ Melt safely, heed the following
warnings and all other warnings that appear in
this manual:
•
Make sure all hose connections are tight.
If you do not, you may be sprayed with
hot shortening. This could result in
serious burns.
•
Make sure no water gets into the
shortening. Water causes hot shortening
to spatter, which could cause serious
burns.
•
Make sure the EZ Melt kettle has enough
room in it before draining shortening
from the fryer. If you do not, shortening
may overflow the kettle and get on the
Belshaw Bros., Inc. • www.belshaw.com • Phone 206-322-5474 • Fax 206-322-5425
iv
MN-1318EN
EZ18, EZ24, EZ34 TS
1
Installation
To help familiarize you with the major parts of
your EZ Melt model EZ18, EZ24, or EZ34, please study the
photographs below.
handle
heater head
filter assembly
kettle
casters
foot pedal
Figure 1-1. Front View.
Belshaw Bros., Inc. • www.belshaw.com • Phone 206-322-5474 • Fax 206-322-5425
EZ18, EZ24, EZ34 TS
MN-1318EN
1
hose connector
filter assembly
heater head
power cord
kettle
frame with
casters
cube melter
foot pedal
Figure 1-2. Side View.
heating
element
kettle
hose connector
supply hose
Figure 1-3. Top View, Heater Head.
Belshaw Bros., Inc. • www.belshaw.com • Phone 206-322-5474 • Fax 206-322-5425
2
MN-1318EN
EZ18, EZ24, EZ34 TS
Reset
button
Pump switch with
pilot light
Heat
switch
with pilot
light
Figure 1-4. Heater head
Bleeder
Pickup tube
Heating
element
kettle
Figure 1-5. Elements and kettle.
Belshaw Bros., Inc. • www.belshaw.com • Phone 206-322-5474 • Fax 206-322-5425
EZ18, EZ24, EZ34 TS
MN-1318EN
3
Thoroughly clean your EZ Melt before using it.
Refer to Section 2 in the Operator's Manual,
“Cleaning,” for cleaning instructions.
WARNING
Moisture causes hot shortening to spatter,
which may cause serious injury. Thoroughly
dry the kettle and any other parts you wash.
WARNING
To avoid electrocuting yourself or damaging
the EZ Melt, never allow water, steam,
cleaning solution, or other liquid to enter the
heater head.
Make sure that the power requirements of the EZ
Melt, shown on the data plate, match your power
source.
Belshaw Bros., Inc. • www.belshaw.com • Phone 206-322-5474 • Fax 206-322-5425
4
MN-1318EN
EZ18, EZ24, EZ34 TS
2
Troubleshooting
This section is designed as an aid in troubleshooting, not as a substitute for a qualified
technician. You may encounter a problem with
your EZ Melt that is not covered in this section,
or you may try the remedies suggested here and
find that they do not correct the problem. In
either case, feel free to call Belshaw Bros. at
(206)322-5474. One of our customer support
representatives will be happy to help you. When
you call, please specify the following:
For factory service, call us for a return goods
authorization. Then send your machine to us,
freight prepaid, with your instructions for
service, your phone number, and the name of the
person for us to contact when we have made a
cost estimate. In most cases, the machine can be
shipped back, freight collect, within five days.
To avoid down time, call us to see whether we
have a machine we can loan to you while your
machine is being serviced.
•
The model number of the machine.
Ship machines in need of servicing to:
•
The serial number of the machine.
•
The voltage, phase, and hertz (cycle) of
the machine.
Belshaw Bros., Inc.
814 44th Street NW, Suite 103
Auburn, WA 98001 USA
CAUTION
If you perform repairs yourself or have them
performed by anyone other than Belshaw
Bros. or a service technician authorized by
Belshaw Bros., you do so at your own risk.
Following is a troubleshooting chart to help you
identify and solve some basic problems.
WARNING
Disconnect the machine from the power
source before disassembling, repairing, or
wiring.
Belshaw Bros., Inc. • www.belshaw.com • Phone 206-322-5474 • Fax 206-322-5425
EZ18, EZ24, EZ34 TS
MN-1318EN
5
THE SHORTENING DOES NOT FLOW FREELY THROUGH THE FILTER
SYSTEM
Possible Causes
What To Do
The hose is crimped.
Straighten the hose.
Solid shortening is building up inside the hose and
pump
Filter shortening at a higher temperature.
WARNING
To avoid being burned, before doing any of the
following, turn off the EZ Melt and allow the
shortening to cool.
The hose is clogged with shortening.
Soak the hose in warm or hot water to help release
the clogged shortening. Hang it up and let it dry
before you use it again.
The drain tube is clogged with solid shortening.
Remove the drain tube and soak it in warm or hot
water to help release the clogged shortening.
The pickup tube is clogged with residue.
Remove the pickup tube and clean it.
THE PUMP MOTOR WILL NOT RUN
Possible Causes
What To Do
The connection of the power cord to the power
source is faulty.
Make sure the power cord is fully plugged in to a
proper power source.
The circuit breaker has been tripped.
Press the reset button.
If the problem persists, consult your Belshaw
dealer, or call Belshaw.
WARNING
Before doing the following, turn off the
machine, allow it to cool, and disconnect it
from the power source.
The power switch is defective.
Repair or replace the power switch.
The motor is defective.
Repair or replace the motor.
Belshaw Bros., Inc. • www.belshaw.com • Phone 206-322-5474 • Fax 206-322-5425
6
MN-1318EN
EZ18, EZ24, EZ34 TS
3
Appendix
See Parts List Drawing Insert Page.
Belshaw Bros., Inc. • www.belshaw.com • Phone 206-322-5474 • Fax 206-322-5425
EZ18, EZ24, EZ34 TS
MN-1318EN
7