T
ReflexMax1™ DVD±R Quick Start Guide
BASIC OPERATION
THIS QUICK START GUIDE HAS BASIC INSTRUCTIONS FOR DUPLICATING DISC-TO-DISC, WHICH
IS COPYING DVD-RS OR DVD+RS FROM A
MASTER DVD PLACED IN THE REFLEXMAX1’S
TOP DRIVE. FOR MORE DETAILED INSTRUCTIONS ON THE REFLEXMAX1’S DUPLICATING
OPERATION, PLEASE REFER TO THE USER’S
GUIDE ON THE ATTACHED CD.
To start the duplication process, load the top drive
with your DVD master. Load the bottom writer
drive with a high-quality blank DVD±R or
DVD±RW.
6 Press the ENT button to begin duplicating. The
ReflexMax1 duplicator will automatically analyze
the master disc (this may take a few moments), and
begin duplicating at the maximum recording
speed.
v1.1
3 Connect the USB cable to the port on the back
of the ReflexMax1. Then connect the other end of
the cable to a USB 2.0 slot on your computer.
4 Power on your computer and the Reflex by
pressing the round button in the lower right-hand
corner. The Reflex will perform a self-test. When
the self-test is complete, the image below will
appear on the LCD screen:
1. Copy
1 Power on the ReflexMax1 by pressing the round
button located at the bottom right on the front of
the unit. The system will initialize and perform a
self-test, which will be shown on the LCD display.
2 When the self-test is complete, 1 Copy will
appear on the LCD display. Press the DOWN arrow
until 8 Select Source appears on the LCD display.
3 Press the ENT button and the following image
should appear on the display:
SRC: DVD-ROM
01 IDE2 Master
If the above image appears on the screen, hit ESC
and proceed to step 5.
4 If the above image does not appear on the
screen, press the DOWN arrow until it displays
SRC: DVD-ROM 01 IDE2 Master. Press the ENT
button and the LCD will display DVD-ROM
Selected. Press ENT again.
7 The LCD will display the writing process as it
happens. The screen will display OK: when the
duplication is complete.
Note: When the duplication process is completed, the
writer drive will automatically eject the DVD-R that has
been duplicated successfully. If the duplication process
failed, the DVD-R will remain in the drive until the eject
button on the drive is pressed. For more information on
why a DVD-R may not copy, please refer to the User’s
Guide on the attached CD.
ACTIVATING USB CONNECTIVITY
IN ORDER TO USE YOUR REFLEXMAX1 DUPLICATOR
AS AN EXTERNAL RECORDER, YOU NEED TO SET IT
TO OPERATE IN USB MODE.
1 Make sure the Reflex and your computer are
both turned off.
2 Locate the small switch next to the USB slot
on the back of the ReflexMax1. Before you connect the USB cable, move the switch to the right
(toward the USB port).
5 Press the UP arrow until you return to 1 Copy.
T
www.discmakers.com
5 The Windows system message Found New
Device may appear during the first time you set up
the ReflexMax1 to your computer.
6 The Reflex will appear as a USB Mass Storage
Device, or USB 2.0 Device. Follow your computer’s on-screen instructions to set up a USB device.
7 In Windows Explorer and My Computer, the
bottom writer drive on the ReflexMax1 will appear
as a Compact Disc Drive icon with a new drive letter, such as E:\. The drive is now ready to read and
write using the provided software or other authoring software. (Please refer to the software’s help
section instructions.)
Note: To use the ReflexMax1 as a standalone duplicator
without the USB to PC connection, the switch located next
to the USB port must be pushed back to the left (away from
the USB port). If the switch is in the USB connection position, the Reflex’s controller will not recognize the writer
drive. If this happens, turn off the Reflex unit and move the
switch to the left. Then turn the Reflex unit back on for normal operations. It’s important to only move the USB switch
when the Reflex is turned off.
1-888-800-4041