ECX ECX03013I Instruction manual

®
TORMENT
™ 1/10 4WD ELECTRIC
ECX03013 | ECX03013AU | ECX03013I
INSTRUCTION MANUAL
BEDIENUNGSANLEITUNG
MANUEL D’UTILISATION
MANUALE DI ISTRUZIONI
SHORT COURSE TRUCK
Congratulations on your purchase of the ECX®
Torment™ Short Course Truck. This 1/10-scale
model introduces you to the sport of RC driving.
Herzlichen Glückwunsch zum Kauf des ECX
Torment Short Course Truck. Dieses 1/10 Scale
Model öffnet Ihnen die Welt des RC Car Sports.
Nous vous félicitons pour l’achat du ECX
Torment Short Course Truck. Ce modèle 1/10
vous initie à la conduite RC.
Congratulazioni per l’acquisto di questo Torment
Short Course Truck ECX. Questa vettura in scala
1/10 vi introdurrà nel mondo dei modelli RC.
EN
NOTICE
All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby, Inc. For
up-to-date product literature, visit http://www.horizonhobby.com and click on the support tab for this product.
Meaning of Special Language:
The following terms are used throughout the product literature to indicate various levels of potential harm when operating this product:
NOTICE: Procedures, which if not properly followed, create a possibility of physical property damage AND little or no possibility of injury.
CAUTION: Procedures, which if not properly followed, create the probability of physical property damage AND a possibility
of serious injury.
WARNING: Procedures, which if not properly followed, create the probability of property damage, collateral damage, and serious
injury OR create a high probability of superficial injury.
WARNING: Read the ENTIRE instruction manual to become familiar with the features of the product before operating.
Failure to operate the product correctly can result in damage to the product, personal property and cause serious injury.
This is a sophisticated hobby product and NOT a toy. It must be operated with caution and common sense and requires some basic
mechanical ability. Failure to operate this Product in a safe and responsible manner could result in injury or damage to the product
or other property. This product is not intended for use by children without direct adult supervision. Do not use with incompatible components or alter this product in any way outside of the instructions provided by Horizon Hobby, Inc. This manual contains
instructions for safety, operation and maintenance. It is essential to read and follow all the instructions and warnings in the manual,
prior to assembly, setup or use, in order to operate correctly and avoid damage or serious injury.
Age Recommendation: Not for children under 14 years. This is not a toy.
Safety Precautions and Warnings
As the user of this product, you are solely responsible for operating in a manner that does not endanger yourself and others or
result in damage to the product or property of others.
This model is controlled by a radio signal subject to interference
from many sources outside your control. This interference can
cause momentary loss of control, so it is advisable to always
keep a safe distance in all directions around your model as this
margin will help avoid collisions or injury.
• Never operate your model with low transmitter batteries.
• Always operate your model in open spaces away from
full-size vehicles, traffic and people.
• Never operate the model in the street or in populated areas
for any reason.
• Carefully follow the directions and warnings for this and any
optional support equipment (chargers, rechargeable battery
packs, etc.) you use.
• Keep all chemicals, small parts and anything electrical out of
the reach of children.
• Never lick or place any portion of the model in your mouth as
it could cause serious injury or even death.
• Exercise caution when using tools and sharp instruments.
• Take care during maintenance as some parts may have sharp
edges.
• Immediately after using your model, do NOT touch equipment
such as the motor, electronic speed control and battery,
because they generate high temperatures. You may burn
yourself seriously touching them.
• Do not put fingers or any objects inside rotating and moving
parts, as this may cause damage or serious injury.
• Always turn on your transmitter before you turn on the
receiver in the car. Always turn off the receiver before turning
your transmitter off.
• Keep the wheels of the model off the ground when checking
the operation of the radio equipment.
TABLE OF CONTENTS
Safety Precautions and Warnings .............................................. 2
Water-Resistant Vehicle
with Waterproof Electronics ................................................. 3
Specifications .......................................................................... 3
Components .............................................................................. 4
Vehicle Preparations .............................................................. 4
Charging the Vehicle Battery ...................................................... 4
Initial Charge ............................................................................... 4
Charging Warnings ..................................................................... 4
Installing Transmitter Batteries .................................................. 5
Transmitter Battery Safety Precautions ...................................... 5
Removing the Vehicle Body ........................................................ 5
Installing the Battery in the Vehicle ........................................... 5
Transmitter controls .................................................................... 6
Changing the Travel Adjust Settings .......................................... 6
Getting Started............................................................................ 7
Installing the Vehicle Body ......................................................... 7
2
TORMENT™
Operation................................................................................... 8
When you are Finished ........................................................... 8
Motor Care ................................................................................ 8
Maintenance ............................................................................ 9
Electronic Speed Control (ESC) ................................................... 9
Electrical Layout .......................................................................... 9
Shock Cleaning............................................................................ 10
Ride Height Adjustment .............................................................. 10
Fasteners ..................................................................................... 10
Binding ........................................................................................ 11
Troubleshooting Guide ................................................................ 11
Limited Warranty ..................................................................... 12
Contact Information................................................................. 12
FCC Information........................................................................ 13
IC Information ........................................................................... 13
Compliance Information for the European Union .............. 14
Parts Diagrams......................................................................... 54
Parts Lists .................................................................................... 56
EN
WATER-RESISTANT VEHICLE WITH WATERPROOF ELECTRONICS
Your new Horizon Hobby vehicle has been designed and built with
a combination of waterproof and water-resistant components to
allow you to operate the product in many “wet conditions”, including
puddles, creeks, wet grass, snow and even rain.
While the entire vehicle is highly water-resistant, it is not completely
waterproof and your vehicle should NOT be treated like a submarine.
The various electronic components used in the vehicle, such as the
Electronic Speed Control (ESC), servo(s) and receiver are waterproof,
however, most of the mechanical components are water-resistant
and should not be submerged.
Metal parts, including the bearings, hinge pins, screws and nuts, as
well as the contacts in the electrical cables, will be susceptible to
corrosion if additional maintenance is not performed after running in
wet conditions. To maximize the long-term performance of your vehicle and to keep the warranty intact, the procedures described in the
“Wet Conditions Maintenance” section below must be performed
regularly if you choose to run in wet conditions. If you are not willing
to perform the additional care and maintenance required, then you
should not operate the vehicle in those conditions.
CAUTION: Failure to exercise caution while using this
product and complying with the following precautions
could result in product malfunction and/or void the warranty.
General Precautions
• Read through the wet conditions maintenance procedures
and make sure that you have all the tools you will need to
properly maintain your vehicle.
• Not all batteries can be used in wet conditions. Consult the
battery manufacturer before use. Caution should be taken
when using Li-Po batteries in wet conditions.
• Most transmitters are not water-resistant. Consult your
transmitter’s manual or the manufacturer before operation.
• Never operate your transmitter or vehicle where lightning may
be present.
• Do not operate your vehicle where it could come in contact
with salt water (ocean water or water on salt-covered roads),
contaminated or polluted water. Salt water is very conductive
and highly corrosive, so use caution.
• Even minimal water contact can reduce the life of your motor
if it has not been certified as water-resistant or waterproof. If
the motor becomes excessively wet, apply very light throttle
until the water is mostly removed from the motor. Running a
wet motor at high speeds may rapidly damage the motor.
• Driving in wet conditions can reduce the life of the motor. The
additional resistance of operating in water causes excess
strain. Alter the gear ratio by using a smaller pinion or larger
spur gear. This will increase torque (and motor life) when
running in mud, deeper puddles, or any wet conditions that will
increase the load on the motor for an extended period of time.
Wet Conditions Maintenance
• Drain any water that has collected in the tires by spinning
them at high speed. With the body removed, place the vehicle
upside down and pull full throttle for a few short bursts until
the water has been removed.
CAUTION: Always keep hands, fingers, tools and any
loose or hanging objects away from rotating parts when
performing the above drying technique.
• Remove the battery pack(s) and dry the contacts. If you have an
air compressor or a can of compressed air, blow out any water
that may be inside the recessed connector housing.
• Remove the tires/wheels from the vehicle and gently rinse the
mud and dirt off with a garden hose. Avoid rinsing the bearings
and transmission.
NOTICE: Never use a pressure washer to clean your vehicle.
• Use an air compressor or a can of compressed air to dry the
vehicle and help remove any water that may have gotten into
small crevices or corners.
• Spray the bearings, drive train, fasteners and other metal
parts with a water-displacing light oil or lubricant. Do not
spray the motor.
• Let the vehicle air dry before you store it. Water (and oil)
may continue to drip for a few hours.
• Increase the frequency of disassembly, inspection and
lubrication of the following:
• Front and rear axle hub assembly bearings.
• All transmission cases, gears and differentials.
• Motor—clean with an aerosol motor cleaner and re-oil
the bushings with lightweight motor oil.
SPECIFICATIONS
Transmitter
Frequency
Modulation
Battery
2.4GHz
DSM, DSM2, Marine
AA x 4
Servo
Power Supply
Output Torque
Operating Speed
Size
4.8V~6V (shared with receiver)
41.66 oz (3 kg-cm)
0.23sec/60 degrees of travel
55.6 x 18 x 30mm
Electronic Speed Control (ESC)
Input Voltage
Electric Capacity (FET)
Electric Capacity (FET)
PWM Frequency
BEC Voltage
Size
Weight
6.0–8.4 V
Forward 40A/180A
Reverse 20A/90A
1kHz
5V/2A
36 x 31.7 x 18mm
65 g
TORMENT™
3
EN
COMPONENTS
1.
2.
3.
4.
5.
ECX Torment 1/10-scale 4WD Short Course Truck
Spektrum™ DX2E Transmitter
AA (4) Batteries
DYN4113 2A Peak Battery Charger
Dynamite® Speedpack™ 8.4V
Ni-MH battery (DYN1062EC)
®
™
3
4
2
1
5
VEHICLE PREPARATIONS
CHARGING THE VEHICLE BATTERY
1. Connect the AC power cord to the power slot on the charger, then
connect the other end of the power cord to an AC power source.
2. The Power LED and Charging LED will turn GREEN when the
charger is connected to the AC power source.
3. Connect the battery pack connector to the charge connector.
4. Press the On/Off button to charge the battery. The Charging LED
turns RED.
5. When the battery pack is fully charged, the Charging LED will turn
GREEN.
6. Press the On/Off button to stop charging. Disconnect the battery
pack connector from the charge connector.
CAUTION: If at any time during the charge process the
battery pack(s) becomes hot to the touch, unplug the
battery immediately and discontinue the charge process.
The vehicle battery charger produces 2000 milliAmps (2 Amps) per
hour. Divide the mAh capacity on the label of a battery by 2000 to know
how long battery charging will require. For example, a fully
discharged 2400mAh battery requires 1.2 hours (72 minutes) to charge.
INITIAL CHARGE
Your Dynamite peak voltage detection charger includes safety circuitry
and programming. The charger will stop charging after 15 minutes if it
senses any issues that have come up in charging. The high electrical
resistance commonly found in new, unconditioned, Ni-MH batteries
can cause this safety circuit to turn off the charger before a full
charging cycle is complete. This is commonly known as a “false peak”
in your battery charge.
Should this occur during your first charge cycle, it does not necessarily
indicate a failure of either your charger or battery. Instead, it shows
that the charger is functioning properly and that the battery is not yet
fully conditioned.
To complete your first full charging cycle in the event of a false peak,
restart the charger by pressing the Start button again. Repeat this
process until the charge cycle continues to charge past 15 minutes.
It may take as many as 2 to 4 restarts to complete your first one or
4
TORMENT™
two full charge cycles. Once your charger completes a charge cycle
longer than 15 minutes, your battery will be fully charged. A typical
first full charge cycle should run for 45 to 90 minutes, depending on the
self-discharge condition of the battery since it was shipped from the
factory.
Once your battery is properly conditioned through a few full charge
and discharge cycles, you will see normal operation of the charger by a
single press of the start button, followed by a 60- to 90- minute charge
cycle.
CHARGING WARNINGS
WARNING: Failure to exercise caution while using this
product and comply with the following warnings could result
in product malfunction, electrical issues, excessive heat, FIRE, and
ultimately injury and property damage.
• Read all safety precautions and literature prior to use of this
product.
• Never leave the battery and charger unattended during use.
• Never allow children under 14 years of age to charge battery
packs.
• Never attempt to charge dead or damaged batteries.
• Never charge a battery if the cable has been pinched or shorted.
• Never allow batteries or charger to come into contact with
moisture at any time.
• Never charge batteries in extremely hot or cold places
(recommended between 50–80°F (10–26°C)) or place in direct
sunlight.
• Always use only Ni-MH rechargeable batteries. This charger
cannot charge batteries such as “heavy duty”, “alkaline”,
“mercury” or “lithium” battery.
• Always connect to the charger correctly.
• Always disconnect the battery and charger after charging and let
them cool between charges.
• Always inspect the battery before charging.
• Always terminate all processes and contact Horizon Hobby if the
product malfunctions.
• Always make sure you know the specifications of the battery to
be charged or discharged to ensure it meets the requirements of
this charger.
• Always constantly monitor the temperature of the battery pack
while charging.
• Always end the charging process if the charger or battery
becomes hot to the touch or starts to change form during the
charge process.
• Always charge in a well ventilated area.
EN
INSTALLING TRANSMITTER BATTERIES
1. Slide the panel open on the bottom of the transmitter.
2. Obey the battery plus (+) and minus (-) diagram in the
transmitter to install 4 AA batteries.
3. Slide the panel closed.
We recommend using only alkaline AA batteries in the
transmitter.
CAUTION: If using rechargeable batteries, charge only
rechargeable batteries. Charging non-rechargeable
batteries may cause the batteries to burst, resulting in injury to
persons and/or damage to property.
TRANSMITTER BATTERY SAFETY PRECAUTIONS
• Never install damaged batteries.
• Never install batteries of mixed types or of different ages in
the transmitter.
• Always remove exhausted batteries.
• Always remove batteries before storing the transmitter.
• Low battery power can result in loss of control of the RC
vehicle.
REMOVING THE VEHICLE BODY
INSTALLING THE BATTERY IN THE VEHICLE
1. Remove the front and rear body clips, then remove the battery
strap.
2. Install a fully charged battery.
3. Install the battery strap.
4. Install the front and rear body clips.
If desired, you can put foam blocks (ECX2015) in front of the battery
so the weight of the battery increases rear traction or in back of the
battery to increase steering response.
TORMENT™
5
EN
TRANSMITTER CONTROLS
REVERSE SWITCH
Allows you to change the
direction of steering (ST. REV)
and throttle (TH. REV) controls
(default settings are “N” for
steering and “N” for throttle).
ST RATE
ST TRIM
Adjust to make the vehicle
drive straight with no input
at the steering wheel.
Adjusts the amount the
front wheels move when the
steering wheel is turned left
or right.
STEERING WHEEL
TH TRIM
Adjusts the neutral point
of the electronic speed
control.
POWER SWITCH
Power on
or off the
transmitter.
BATTERY LEVEL
INDICATOR
Solid Green: Battery
voltage is good (above
4V).
Flashing Green: Battery
voltage is critically low
(below 4V). Replace
batteries.
Control steering. Right and
Left steering with ST. REV
Switch on N
(see ST. REV switch).
THROTTLE TRIGGER
Forward
Stop
(when TH.
REV switch on N).
Reverse
(when TH.
REV switch
on N).
Controls power to motor for forward
or reverse (see TH. REV switch).
CHANGING THE TRAVEL ADJUST SETTINGS
The travel function supports precise endpoint adjustments in
each direction for the steering and throttle channels.
1. Hold the trigger in the full brake position while powering
on the transmitter. The LED flashes rapidly, indicating the
programming mode is active.
2. Throttle End Point: Hold the trigger in the full throttle position.
Turn the TH TRIM knob to adjust the full throttle end point.
3. Brake End Point: Hold the trigger in the full brake position.
Turn the TH TRIM knob to adjust the full brake end point.
Return the trigger to the center position.
6
TORMENT™
4. Left Steering End Point: Hold the steering wheel in the full left
position. Turn the ST TRIM knob to adjust the left end point.
5. Right Steering End Point: Hold the steering wheel in the full
right position. Turn the ST TRIM knob to adjust the right end
point. Return the steering wheel to the center position.
6. Power off the transmitter to save the travel adjust settings.
The minimum Travel is 75%, and the Maximum travel is
150%. The default travel settings are 125% steering and
100% throttle.
EN
GETTING STARTED
1. Power on the transmitter.
2. Power on the ESC.
3. Do a test of the transmitter’s control of the vehicle with
the vehicle’s wheels off the ground.
4. Start driving slowly, and, if the vehicle does not go
straight, adjust the steering trim dial on the transmitter.
IMPORTANT: Seat the motor brushes by driving smoothly
on a flat surface during use of the first battery charge.
Properly seating the motor brushes will increase the life and
performance of the motor.
INSTALLING THE VEHICLE BODY
TORMENT™
7
EN
OPERATION
• ALWAYS turn on your transmitter before you turn on the
receiver in the vehicle. Always power off the receiver before
turning your transmitter off.
• ALWAYS operate your vehicle in a wide open area. Operating
the vehicle in a small space or indoors can cause overheating
at low speeds. Operating at low speed increases heat in the
electronic speed control (ESC). Overheating can damage the
vehicle and failure may result.
WHEN YOU ARE FINISHED
1. Power off the Electronic
Speed Control (ESC).
2. Disconnect the battery.
3. Power off the transmitter.
5. Recharge the battery.
4. Remove the battery from the vehicle.
MOTOR CARE
• Seat the motor brushes by driving smoothly on a flat surface
during use of the first battery charge. Failing to do so can
greatly reduce motor performance and functional life.
• Prolong motor life by preventing overheating conditions.
Undue motor wear results from frequent turns, stops and
8
TORMENT™
starts, pushing objects, driving in water and tall grass,
and driving continuously up hill.
• Over-temperature protection is installed on the ESC to
prevent circuit damage, but cannot protect the motor from
driving against heavy resistance.
EN
MAINTENANCE
ELECTRONIC SPEED CONTROL (ESC)
Programming: The ESC comes with two jumpers pre-installed in
the REV: ON and BATT: Ni-MH configurations.
To disable reverse or change battery type to Li-Po, disconnect the
jumper from the default port and connect it to the desired port.
Power off the ESC, then power it back on.
If the jumpers are lost or not installed, the ESC will default to
REV: ON and BATT: Li-Po.
Operation
LED Status
Stop
Forward
Forward (full speed)
Reverse
Brake
Brake (full brake)
Ni-MH/Ni-Cd Battery
2S Li-Po Battery
ESC Ready
Battery Low Voltage
Overheat
OFF
Blinks
Solid
Blinks
Blinks
Solid
LED
Sound at Power UP
1 Short Beep
2 Short Beeps
1 Long Beep
Blinks
Blinks
ELECTRICAL LAYOUT
Part #
Description
A
DYN1172
Motor B
DYN1062EC
Battery 8.4V
C
SPMS603
Waterproof Steering
Servo
D
SPMSR201
Waterproof Receiver
E
DYNS2211
Waterproof Electronic
Speed Control (ESC)
F
Channel 1
G
Channel 2
A
E
B
EC3
EC3
D
C
G
For correct operation, Channels 1 and 2
must be used as shown in the wiring diagram.
The motor can be disconnected from the ESC
at the connectors in the wiring.
F
TORMENT™
9
EN
SHOCK CLEANING
Oil-filled shocks will require regular maintenance due to the oil breaking
down or getting dirty. This maintenance should be performed after about
every 3 to 5 hours of use, depending on the conditions that the vehicle is
used in.
• Remove the shock from the vehicle.
• Remove the cap from the shock body and dispose of fluid.
• Disassemble the shock. Clean thoroughly with DYN5505. Dry parts
before assembly.
• Re-assemble the shock and refill the shock body with silicone fluid (30
weight recommended).
• Slowly move the shaft and piston up and down to remove air bubbles.
• Move the piston to the midway point of the body and install the cap.
• Wipe off any overflowing fluid.
• When properly filled, the piston should rebound about 3/8 in (9.5mm)
after being pushed in fully.
• Re-install the shock on the vehicle.
SHOCK PARTS
DIAGRAM
ECX233000
ECX234005
ECX236001
ECX233002
ECX233001
ECX236004
ECX233001
Ride Height Adjustment
Ride height is an adjustment that affects the way the vehicle jumps,
turns and goes over bumps. Drop one end of the vehicle from approximately 6 inches (152 mm) in height onto a flat surface. When dropping
the front of the vehicle, after the vehicle settles, make sure the front
arms are equal and parallel to the flat surface. Do the same with the rear
to make sure both arms are parallel with the flat surface.
Lowering the front ride height increases steering, but decreases
traction. Lowering the rear ride height increases traction, but decreases
steering.
ECX233003
ECX233002
ECX234005
Part #
ECX233000
ECX233001
ECX233002
ECX233003
Description
Shock, Complete, (2): 4wd
Shock Rebuild, (2): 4wd
Top, Bottom Shock Ends: 4wd
Shock Spring, Black, Set: 4wd
Part #
ECX234005
ECX236001
ECX236004
Description
Link Set, Plastic: 1:10 4wd All
Lock Nut, M2.5, (5)
Special Hardware: 1:10 4wd All
FASTENERS
Description
10
Description
Description
Description
Tapping Binder Head, M2.5x4mm
Tapping Binder Head, M3x22mm
Binder Head, M3x16mm
Setscrew, M3x3mm
Tapping Binder Head, M3x8mm
Tapping Binder Head, M3x25mm
Binder Head, M3x18mm
Setscrew, M4x3mm
Tapping Binder Head, M3x10mm
Tapping Flat Head, M2.5x10mm
Binder Head, M3x20mm
Tapping Binder Head, M3x12mm
Tapping Flat Head, M3x10mm
Binder Head, M3x22mm
Tapping Binder Head, M3x14mm
Tapping Flat Head, M3x15mm
Flat Head, M3x8mm
Tapping Binder Head, M3x16mm
Binder Head, M3x10mm
Flat Head, M3x10mm
Tapping Binder Head, M3x18mm
Binder Head, M3x12mm
Flat Head, M4x18mm
Tapping Binder Head, M3x20mm
Binder Head, M3x14mm
TORMENT™
Washer,
6.2x10.8x0.2mm
Washer,
3x8x1mm
Washer,
2.6x6 X0.5mm
Flanged Lock Nut, M4
Lock Nut M3
Lock Nut M2.5
EN
BINDING
Binding is the process of programming the receiver to recognize
the GUID (Globally Unique Identifier) code of a single specific
transmitter. The DX2E and SR201 receiver are bound at the factory. If you need to rebind, follow the instructions below.
1. With the receiver off, insert the bind plug into the BIND port
on the receiver.
2. Power the receiver through any other port. The orange LED
will flash continuously, indicating the receiver is in bind mode.
3. With the steering wheel and throttle trigger in the failsafe
positions, normally full brakes and straight steering (see the
Failsafe section on this page for more information), press and
hold the bind button and turn on the transmitter. The green
LED on the front of the transmitter will flash within three
seconds, indicating the transmitter is in bind mode.
4. Release the bind button when the green LED flashes.
Continue to hold the steering wheel and throttle trigger in the
failsafe positions until the LED on the receiver glows solid.
Bind Button
5. The LED on the receiver will glow solid when the transmitter
and receiver are bound.
6. Remove the bind plug and store it in a convenient place.
You must rebind when:
• Different failsafe positions are desired e.g., when throttle or
steering reversing has been changed.
• Changing receiver types e.g., changing from a DSM® receiver
to a DSM2® or Marine receiver.
• Binding the receiver to a different transmitter.
Some Spektrum receivers, like the SR3001, use a bind button
rather than a bind plug. The binding process is the same with
this receiver, however, instead of inserting the plug before
powering up the receiver, press and hold the bind button while
powering up the receiver to enter bind mode.
FAILSAFE
In the unlikely event that the radio link is lost during use, the
receiver will drive the servos to their preprogrammed failsafe
positions (normally full brakes and straight steering). If the
receiver is turned on prior to turning on the transmitter, the
receiver will enter failsafe mode, driving the servos to their
preset failsafe positions. When the transmitter is turned on,
normal control is resumed. Failsafe servo positions are set
during binding (see binding a receiver above).
TROUBLESHOOTING GUIDE
Problem
Short Run Time
Sluggish Action
Controls Reversed
Motor/ESC overheat
Doesn’t Operate
Poor Range
The system will not
connect
Possible Cause
• Battery damaged/not charged
• Motor dirty or brushes worn
• Motor dirty or brushes worn
• Bind in drivetrain
• Vehicle battery is not charged
• ST. REV or TH. REV
• Over-geared for the driving environment
• Transmitter batteries low
• Transmitter powered off
• ESC powered off
• Vehicle battery is not charged
• Transmitter batteries low
• Receiver antenna damaged
• Transmitter and receiver too near each other
• Transmitter and receiver too near large
metal objects (vehicles, etc.)
• Receiver accidentally put in bind mode so
receiver is no longer bound
• Check the receiver antenna to be sure it is
not cut or damaged
The receiver goes into
failsafe mode a short
distance away from the
transmitter
The receiver quits re• Low battery voltage
sponding during operation • Loose or damaged wires or connectors
between battery and receiver
Receiver loses its bind
• Transmitter accidentally put in bind mode,
ending bind to receiver
Solution
• Check/change battery
• Check/clean/replace
• Check/clean/replace
• Clean/adjust
• Replace/recharge
• Change switch position
• Install smaller pinion
• Replace/recharge
• Power On
• Power On
• Replace/recharge
• Replace/recharge
• Check/repair/replace
• Move transmitter 8–12 feet (2.4–3.6m) from
receiver
• Move away from large metal objects (vehicles, etc.)
• Rebind transmitter and receiver
• Contact Horizon Product Support
• Make sure receiver antenna is in an antenna tube
and is above vehicle
• Completely recharge battery
• Do a check of the wires and connection between
battery and receiver. Repair or replace wires and/
or connectors
• Bind transmitter to receiver
TORMENT™
11
EN
LIMITED WARRANTY
What this Warranty Covers
Horizon Hobby, Inc., (Horizon) warrants to the original purchaser
that the product purchased (the "Product") will be free from defects
in materials and workmanship at the date of purchase.
What is Not Covered
This warranty is not transferable and does not cover (i) cosmetic
damage, (ii) damage due to acts of God, accident, misuse, abuse,
negligence, commercial use, or due to improper use, installation,
operation or maintenance, (iii) modification of or to any part of
the Product, (iv) attempted service by anyone other than a Horizon
Hobby authorized service center, (v) Product not purchased from
an authorized Horizon dealer, or (vi) Product not compliant with
applicable technical regulations.
OTHER THAN THE EXPRESS WARRANTY ABOVE, HORIZON
MAKES NO OTHER WARRANTY OR REPRESENTATION, AND
HEREBY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES,
INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES
OF NON-INFRINGEMENT, MERCHANTABILITY AND FITNESS FOR
A PARTICULAR PURPOSE. THE PURCHASER ACKNOWLEDGES
THAT THEY ALONE HAVE DETERMINED THAT THE PRODUCT WILL
SUITABLY MEET THE REQUIREMENTS OF THE PURCHASER’S
INTENDED USE.
Purchaser’s Remedy
Horizon’s sole obligation and purchaser’s sole and exclusive
remedy shall be that Horizon will, at its option, either (i) service,
or (ii) replace, any Product determined by Horizon to be defective.
Horizon reserves the right to inspect any and all Product(s) involved
in a warranty claim. Service or replacement decisions are at the
sole discretion of Horizon. Proof of purchase is required for all warranty claims. SERVICE OR REPLACEMENT AS PROVIDED UNDER
THIS WARRANTY IS THE PURCHASER’S SOLE AND EXCLUSIVE
REMEDY.
Limitation of Liability
HORIZON SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR
PRODUCTION OR COMMERCIAL LOSS IN ANY WAY, REGARDLESS
OF WHETHER SUCH CLAIM IS BASED IN CONTRACT, WARRANTY,
TORT, NEGLIGENCE, STRICT LIABILITY OR ANY OTHER THEORY
OF LIABILITY, EVEN IF HORIZON HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Further, in no event shall the liability
of Horizon exceed the individual price of the Product on which
liability is asserted. As Horizon has no control over use, setup, final
assembly, modification or misuse, no liability shall be assumed
nor accepted for any resulting damage or injury. By the act of use,
setup or assembly, the user accepts all resulting liability. If you as
the purchaser or user are not prepared to accept the liability associated with the use of the Product, purchaser is advised to return
the Product immediately in new and unused condition to the place
of purchase.
Law
These terms are governed by Illinois law (without regard to conflict
of law principals). This warranty gives you specific legal rights,
and you may also have other rights which vary from state to state.
Horizon reserves the right to change or modify this warranty at any
time without notice.
WARRANTY SERVICES
Questions, Assistance, and Services
Your local hobby store and/or place of purchase cannot provide
warranty support or service. Once assembly, setup or use of the
Product has been started, you must contact your local distributor
or Horizon directly. This will enable Horizon to better answer your
questions and service you in the event that you may need any
12
TORMENT™
assistance. For questions or assistance, please visit our website
at www.horizonhobby.com, submit a Product Support Inquiry, or
call the toll free telephone number referenced in the Warranty
and Service Contact Information section to speak with a Product
Support representative.
Inspection or Services
If this Product needs to be inspected or serviced and is compliant in
the country you live and use the Product in, please use the Horizon
Online Service Request submission process found on our website
or call Horizon to obtain a Return Merchandise Authorization (RMA)
number. Pack the Product securely using a shipping carton. Please
note that original boxes may be included, but are not designed to
withstand the rigors of shipping without additional protection. Ship
via a carrier that provides tracking and insurance for lost or damaged parcels, as Horizon is not responsible for merchandise until
it arrives and is accepted at our facility. An Online Service Request
is available at http://www.horizonhobby.com/content/_servicecenter_render-service-center. If you do not have internet access,
please contact Horizon Product Support to obtain a RMA number
along with instructions for submitting your product for service.
When calling Horizon, you will be asked to provide your complete
name, street address, email address and phone number where you
can be reached during business hours. When sending product into
Horizon, please include your RMA number, a list of the included
items, and a brief summary of the problem. A copy of your original
sales receipt must be included for warranty consideration. Be sure
your name, address, and RMA number are clearly written on the
outside of the shipping carton.
NOTICE: Do not ship LiPo batteries to Horizon. If you have
any issue with a LiPo battery, please contact the appropriate Horizon Product Support office.
Warranty Requirements
For Warranty consideration, you must include your original
sales receipt verifying the proof-of-purchase date. Provided
warranty conditions have been met, your Product will be serviced
or replaced free of charge. Service or replacement decisions are at
the sole discretion of Horizon.
Non-Warranty Service
Should your service not be covered by warranty, service
will be completed and payment will be required without
notification or estimate of the expense unless the expense
exceeds 50% of the retail purchase cost. By submitting the
item for service you are agreeing to payment of the service without
notification. Service estimates are available upon request. You
must include this request with your item submitted for service.
Non-warranty service estimates will be billed a minimum of ½ hour
of labor. In addition you will be billed for return freight. Horizon
accepts money orders and cashier’s checks, as well as Visa, MasterCard, American Express, and Discover cards. By submitting any
item to Horizon for service, you are agreeing to Horizon’s Terms and
Conditions found on our website http://www.horizonhobby.com/
content/_service-center_render-service-center.
ATTENTION: Horizon service is limited to Product compliant in the country of use and ownership. If received, a
non-compliant Product will not be serviced. Further, the
sender will be responsible for arranging return shipment of the un-serviced Product, through a carrier of the
sender’s choice and at the sender’s expense. Horizon will
hold non-compliant Product for a period of 60 days from
notification, after which it will be discarded.
EN
CONTACT INFORMATION
Country of Purchase
Horizon Hobby
Horizon Service Center
(Repairs and Repair Requests)
Horizon Product Support
United States of America (Product Technical Assistance)
Sales
United Kingdom
Service/Parts/Sales:
Horizon Hobby Limited
Germany
Horizon Technischer Service
Sales: Horizon Hobby GmbH
France
Service/Parts/Sales:
Horizon Hobby SAS
China
Service/Parts/Sales:
Horizon Hobby – China
Contact Information
servicecenter.horizonhobby.com/
RequestForm/
www.quickbase.com/db/
bghj7ey8c?a=GenNewRecord
888-959-2306
sales@horizonhobby.com
888-959-2306
sales@horizonhobby.co.uk
+44 (0) 1279 641 097
service@horizonhobby.de
+49 (0) 4121 2655 100
infofrance@horizonhobby.com
+33 (0) 1 60 18 34 90
info@horizonhobby.com.cn
+86 (021) 5180 9868
Address
4105 Fieldstone Rd
Champaign, Illinois, 61822 USA
Units 1–4 , Ployters Rd, Staple Tye
Harlow, Essex, CM18 7NS, United
Kingdom
Christian-Junge-Straße 1
25337 Elmshorn, Germany
11 Rue Georges Charpak
77127 Lieusaint, France
Room 506, No. 97 Changshou Rd.
Shanghai, China 200060
FCC INFORMATION
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
CAUTION: Changes or modifications not expressly
approved by the party responsible for compliance could void
the user’s authority to operate the equipment.
This product contains a radio transmitter with wireless technology
which has been tested and found to be compliant with the applicable regulations governing a radio transmitter in the 2.400GHz to
2.4835GHz frequency range.
Antenna Separation Distance
maintain a separation distance of at least 5 cm between your body
(excluding fingers, hands, wrists, ankles and feet) and the antenna to
meet RF exposure safety requirements as determined by FCC
regulations.
The following
illustrations show
the approximate
5 cm RF exposure
area and typical
hand placement
when operating
your Spektrum
transmitter.
When operating your Spektrum transmitter, please be sure to
IC INFORMATION
This device complies with Industry Canada license-exempt RSS
standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this device must
accept any interference, including interference that may cause undesired operation of the device.
TORMENT™
13
EN
COMPLIANCE INFORMATION FOR THE EUROPEAN UNION
AT
EE
IE
PL
IS
BE BG
ES FI
IT LT
PT RO
LI NO
Instructions for disposal of WEEE
by users in the European Union
CZ CY DE DK
FR GR HR HU
LU LV MT NL
SE SI SK UK
CH
Declaration of Conformity
(in accordance with ISO/IEC 17050-1)
No. HH2014012401
Product(s):
ECX Torment 1:10 4WD SCT Brushed RTR
(Spektrum DX2E transmitter and SR201 receiver
included)
Item Number(s): ECX03013I
Equipment class: 2
The object of declaration described above is in conformity with
the requirements of the specifications listed below, following
the provisions of the European R&TTE Directive 1999/5/EC, EMC
Directive 2004/108/EC and LVD Directive 2006/95/EC:
EN 300-328 V1.7.1: 2006
EN 301 489-1 V1.9.2: 2012
EN301 489-17 V2.1.1: 2009
EN60950-1:2006+A11:2009+A1:2010+A12: 2011
EN55022:2010 + AC:2011
EN55024:2010
EN61000-3-2:2006+A1:2009+A2:2009
EN61000-3-3:2008
Signed for and on behalf of:
Horizon Hobby, Inc.
Champaign, IL USA
Jan. 24, 2014
14
Robert Peak
Chief Financial Officer
Horizon Hobby, Inc.
TORMENT™
This product must not be disposed of with other waste.
Instead, it is the user’s responsibility to dispose of their
waste equipment by handing it over to a designated collections point for the recycling of waste electrical and electronic
equipment. The separate collection and recycling of your waste
equipment at the time of disposal will help to conserve natural
resources and ensure that it is recycled in a manner that protects
human health and the environment. For more information about
where you can drop off your waste equipment for recycling,
please contact your local city office, your household waste
disposal service or where you purchased the product.
PARTS DIAGRAM | EXPLOSIONSZEICHNUNG | VUE ÉCLATÉE DES PIÈCES |
ESPLOSO DEL MODELLO CON REFERENZA PEZZI
RECOMMENDED ITEMS
EMPFOHLENE WERKZEUGE
OUTILS RECOMMANDÉS
ATTREZZI CONSIGLIATI
45
2
61
63
47
9
1
11
62
45
45
2 mm
1.5 mm
45
44
42
10
11
45
45
59
21
12
59
9
47
9
1
33
20
14
7
45
46
60
47
47
3
42
45
8
8
45
7
45
42
5
10
45
7
15
9
45
44
42
46
45
5
42
7
44
7
45
46
38
31
6
25
44
31
31
48
25
45
42
52
19
7
6
45
54
5
38
42
7
TORMENT™
57
41
5
34
54
38
7
48
56
58
PARTS DIAGRAM | EXPLOSIONSZEICHNUNG | VUE ÉCLATÉE DES PIÈCES |
ESPLOSO DEL MODELLO CON REFERENZA PEZZI
15
45
3
14
45
45
34
5
5
45
45
44
18
42
45
45
44
25
52
23
55
57
40
5
54
52
6
5
24
1
25
17
19
43
56
39
22
43
6
30
45
58
45
16
53
3
3
16
53
28
4
4
26
50
27
25
30
52
16
51 25
29
52
29
50
4
27
25
26
27
30
25
28
16
51
53
4
53
43
TORMENT™
55
Replacement Parts / Ersatzteile / Pièces de rechange / Pezzi di ricambio
Part # | Nummer
Description
Numéro | Codice
1 ECX0941
Set Screw Pack
2 ECX1087
3 ECX231004
4 ECX231005
5 ECX231006
6 ECX231007
7 ECX231008
8 ECX231009
9 ECX231010
10 ECX231011
11 ECX231013
12 ECX231014
13 ECX231015
14 ECX231016
15 ECX231018
16 ECX232010
17 ECX232011
18 ECX232012
19 ECX232013
20 ECX232014
21 ECX232015
22 ECX232017
23 ECX232018
24 ECX232019
25 ECX232020
26 ECX232021
27 ECX232022
28 ECX232023
29 ECX232024
30 ECX232025
31 ECX232026
56
Antenna Tube (1)
Front/Rear Shock Tower Set:
1:10 4wd All
Front/Rear Differential
Gearbox Set: 1:10 4wd All
Front/Rear Toe Plates w/
Inserts: 1:10 4wd All
Hinge Pin Set: 1:10 4wd All
Bell-Crank Set w/Post and
Bushing: 1:10 4wd All
Hinge Pin & Steering Brace:
1:10 4wd All
Beschreibung
Description
Descrizione
ECX Schraubenset
Electrix Empfängerantenne mit
Röhrchen
ECX Dämpferbrücke v/h 1:10
alle 4WD
ECX Differentialgehäuseset
1:10 alle 4WD
ECX Spureinsätze v/h 1:10
alle 4WD
ECX Querlenkerstifthalter 1:10
alle 4WD
ECX Lenkhebelset m. Halter u.
Lager 1:10 alle 4WD
ECX Querlenkerstift Halter 1:10
alle 4WD
ECX Getriebeabdeckung / Kick
Platte/ Akkuhalter 1:10 alle
4WD
Chassis u. oberes Deck Lang
(1) 1:10 4WD Torment
Sachet de vis sans tête
Confezione grani
Tube d'antenne (1)
Tubetto antenna (1)
Supports d'amortisseurs avant
et arrière
Carter de différentiel avant/
arrière
Cales de pincement avant/
arrière avec inserts
Set torre ammort. anter. e poster.
1:10 4wd tutti
Set ingranaggi differenziale anter.
/ poster. 1:10 4wd tutti
Piastre c/inserti convergenza
anter./poster. 1:10 4wd tutti
Set d'axes de suspension
Set perno cerniera 1:10 4wd tutti
Set squadrette con appoggi e
Biellettes et renvois de direction
boccole 1:10 4wd tutti
Renfort avant et support de pivot Perno cerniera e supporti sterzo
de triangle sup
1:10 4wd tutti
Couvercle de couronne/Cale
Gear Cover/Kick Plate/Bttry
Coperchi ingran/piastra rinvio/
de chasse/Plots de support de
Mnts: 1:10 4wd All
supp. batteria 1:10 4wd tutti
batterie
Châssis long et platine
Telaio & parte superiore, lungo
Chassis & Upper Deck, Long
supérieure (1) : Torment 1/10
(1): 1:10 4wd Torment
(1): 1:10 4wd Torment
4wd
Servo Saver, 23T/25T
ECX Servo Saver,23/ 25T
Sauve servo, 23T/25T
Salva servo 23T/25T
Short Battery Strap: 1:10
ECX Akkuverschluss kurz 1:10
Fascetta corta batteria 1:10
Support de batterie court
4wd All
alle 4WD
4wd tutti
Long Battery Strap: 1:10
ECX Akkuverschluss lang 1:10
Fascetta lunga batteria 1:10
Support de batterie long
4wd All
alle 4WD
4wd tutti
Body Post & Mounts: 1:10
ECX Karosserieträger und
Appoggi e supporti batteria 1:10
Supports de carrosserie
4wd All
Halter 1:10 alle 4WD
4wd tutti
Front Bumper Set: 1:10 4wd Stoßfänger vorne 1:10 4WD
Pare-Choc avant : Torment 1/10 Set paraurti anteriore: 1:10 4wd
Torment
Torment
4wd
Torment
Differential, Complete: 1:10 ECX Differential kpl. 1:10 alle
Differenziale completo 1:10
Différentiel complet
4wd All
4WD
4wd tutti
Rear Stub Axle (2): 1:10
ECX Hinterachse (2) 1:10 alle
Snodo fuso posteriore (2): 1:10
Axe de roues arrière (2)
4wd All
4WD
4wd tutti
Rear Dog Bone (2): 1:10
ECX Antriebsknochen hinten (2)
Semiasse snodato posteriore (2):
Tige de cardan arrière (2)
4wd All
1:10 alle 4WD
1:10 4wd tutti
Wheel Hex Set, (4): 1:10
ECX Radmuttern (4) 1:10 alle
Set esagoni ruota (4): 1:10 4wd
Hexagone de roue (4)
4wd All
4WD
tutti
Motor Plate, Aluminum Set: ECX Motorplatte Aluminium
Set piastra motore, alluminio 1:10
Support moteur en aluminium
1:10 4wd All
Set 1:10 alle 4WD
4wd tutti
Main Driveshaft, Long (1):
Antriebswelle lang (1) 1:120
Cardan central long : Torment
Albero di trasmissione principale,
1:10 4wd Torment
wd Torment
1/10 4wd
lungo (1): 1:10 4wd Torment
Slipper, Complete: 1:10
ECX Rutschkupplung kpl 1:10
Slipper complet
Slipper completo 1:10 4wd tutti
4wd All
4WD Cir
ECX Rutschkupplung Belag
Slipper Pad: 1:10 4wd All
Garniture de slipper
Pattini slipper 1:10 4wd tutti
1:10 alle 4WD
Spur Gear, 45T, Mod 1 (2):
ECX Zahnrad 87 Zähne (1) alle
Corona 45T, Mod 1 (2): 1:10 4wd
Couronne 45T, mod 1 (2)
1:10 4wd All
4WD
tutti
Drivetrain Roller Pin Set, (11): ECX Drivetrain Roller Pin Set,
Set perni rulli trasmissione (11):
Set de goupilles cylindriques (11)
1:10 4wd All
(11): 1:10 4wd All
1:10 4wd tutti
Differential Case, Complete : ECX Differential Gehäuse kpl.
Scatola differenziale completa
Corps de différentiel
1:10 4wd All
1:10 alle 4WD
1:10 4wd tutti
Ring & Pinion, Set: 1:10
ECX Tellerrad u. Ritzel 1:10
Couronne de diff et pignon
Set anelli e pignoni 1:10 4wd tutti
4wd All
alle 4WD
conique
Differential Outdrives, (2):
ECX Differential Abtriebe (2)
Trascinatori differenziale (2): 1:10
Noix de sortie de différentiel (2)
1:10 4wd All
1:10 alle 4WD
4wd tutti
Differential Rebuild, (2):
ECX Diff. Rep-Set 1:10 alle
Differenziale rigenerato (2):
Kit de joints de différentiel
1:10 4wd All
4WD
1:10 4wd tutti
Center Drive, Out Drives: 1:10 ECX Antriebswelle Mitte 1:10
Trasmissione centrale e semiassi
Noix de cardan central (2)
4wd All
alle 4WD
1:10 4wd tutti
Front, Driveshafts, Set (2):
Set trasmissione anteriore (2):
ECX CVD Set: 1:10 4WD alle (2) Cardan avant (2)
1:10 4wd All
1:10 4wd tutti
TORMENT™
32
33
34
35
36
37
38
39
Part # | Nummer
Description
Numéro | Codice
Driveshaft Rebuild, (2):
ECX232027
1:10 4wd All
Pinion Gear, 9T/12T x 3mm,
ECX232028
Mod 1
Shock, Complete, (2):
ECX233000
1:10 4wd All
Shock Rebuild, (2):
ECX233001
1:10 4wd All
Top, Bottom Shock Ends: 1:10
ECX233002
4wd All
Shock Spring, Black, Set: 1:10
ECX233003
4wd All
Front Suspension Arm Set:
ECX234001
1:10 4wd All
Rear Suspension Arm Set:
ECX234002
1:10 4wd All
40 ECX234003
41 ECX234004
42 ECX234005
43 ECX235001
44 ECX235002
45 ECX235003
46 ECX235004
47 ECX235005
48 ECX235006
49 ECX236001
50 ECX236004
51 ECX1015
52 ECX1055
53 ECX237000
54 ECX237001
55 ECX237002
56 ECX4802
57 ECX4003
Beschreibung
ECX Reparaturset
Antriebswelle: (2) 1:10 alle WD
ECX Ritzel 9T/12T x 3mm,
Mod 1
ECX Stoßdämpfer kpl. (2) 1:10
alle 4WD
ECX Stoßdämpfer Reparaturset
(2) 1:10 alle 4WD
ECX Stoßdämpferendstücke
oben /unten (2)1:10 alle 4WD
ECX Dämpferfedern Set
Schwarz (4) 1:10 alle 4WD
ECX Querlenkerarme vorne Set
(2) 1:10 alle 4WD
ECX Querlenkerarme hinten Set
(2) 1:10 alle 4WD
ECX Radträger hinten Set (2)
Rear Hub Set: 1:10 4wd All
1:10 alle 4WD
Front Steering Hub Set:
ECX Rad / Lenkträger Set vorne
1:10 4wd All
(2) 1:10 alle 4 WD
Link Set, Plastic:
ECX Anlenkungen Kunststoff
1:10 4wd All
Set (6) 1:10 alle 4 WD
Screw, M2.5, M2 (20)
ECX Schrauben M2,5, M2 (20)
Screw, M3, Flat Head,
ECX M3 Schrauben Flachkopf
Self-Tapping (25)
(25)
ECX M3 Schrauben Flachkopf
Screw, M3, Self-Tapping (35)
selbstschneidend (25)
Screw, M3, Flat Head, (10)
ECX M3 Schrauben (10)
Screw, M3, Binder Head (45) ECX M3 Schrauben (45)
ECX M4 Schrauben Flachkopf
Screw, M4, Flat Head, (5)
(5)
Lock Nut, M2.5, (5)
ECX Stopmutter M2.5
Special Hardware:
ECX Spezialzubehör 1:10 alle
1:10 4wd All
4WD
5x10x4mm Ball Bearing (8)
Radlager Set: Circuit
10x15x4mm Ball Bearing (2) Kugellager 10X15X4 (2): Circuit
Ball Bearing, 12x18xT4mm, ECX Kugellager, 12x18xT4mm,
(4)
(4)
ECX Kugellager, 6x12xT4mm,
Ball Bearing, 6x12xT4mm, (4)
(4)
ECX Kugellager, 8x12xT4mm,
Ball Bearing, 8x14xT4mm, (4)
(4)
Front/Rear Wheel (2): 1:10
ECX v/h Räder: 1:10 4WD
4wd Torment
Torment (2)
FR/R Wheel & Tire,
ECX Vorder / Hinterrad + Reifen
Premount (2): Torment
montiert 1:10 4WD Torment (2)
58 ECX1060
M4 Locknut, Flanged (4)
M4 Stoppmutter (4): Circuit
59
60
61
62
Body Clips (8)
Brushed Motor
Brushed ESC
Servo
Karosserie Clips (8): Circuit
Bürstenmotor
Regler Bürste
Servo
Spektrum SR201 2 Kanal DSM
Sport Surface Empfänger spritzwasserfest
Stoßfänger hinten 1:10 4WD
Torment
Karosserie Grau/Schwarz 1:10
2wd& 4wd Torment
Spektrum DX2E 2 Kanal DSMR
Fernsteuerungs System
ECX1048
DYNS1215
DYNS2210
SPMS603
63 SPMSR201
64 ECX231019
ECX230013
SPM2322
SR201 2Ch DSM Sport
Surface Rx - Coated
Rear Bumper Set: 1:10 4wd
Torment
Body, Grey/Black:
1:10 2wd & 4wd Torment
DX2E 2-Ch DSMR
Surface Radio
Description
Descrizione
Kit de réparation de cardan
avant (2)
Albero di trasmissione rigenerato
(2): 1:10 4wd tutti
Pignon 9T/12Tx 3mm, mod 1
Pignone 9T/12T x 3mm, Mod 1
Amortisseur complet (2)
Kit de réparation d'amortisseur
(2)
Chapes, coupelle, cales
d'amortisseurs
Set de ressorts noirs
Set de triangles avant
Set de triangles arrière
Fusée arrière (2)
Ammortizzatore completo (2):
1:10 4wd tutti
Ammortizzatore rigenerato (2):
1:10 4wd tutti
Terminali superiore e inferiore
ammortizzatore 1:10 4wd tutti
Set molle nere ammortizzatore
1:10 4wd tutti
Set bracci sospensioni anter. 1:10
4wd tutti
Set bracci sospensioni poster.
1:10 4wd tutti
Set mozzi poster. 1:10 4wd tutti
Set de biellettes plastique avec
rotules
Vis M2 et M2.5 (20)
Vis auto-taraudeuse à tête
fraisée M3 (25)
Set mozzo sterzo anter. 1:10
4wd tutti
Set collegamento, plastica
1:10 4wd tutti
Vite M2.5, M2 (20)
Vite M3, Testa piatta,
autofilettante (25)
Vis auto-taraudeuse M3 (35)
Vite M3, Autofilettante (35)
Vis à tête fraisée M3 (10)
vis à tête bombée M3 (45)
Vite M3, Testa piatta (10)
Vite, M3, Testa vincolante (45)
Vis à tête fraisée M4 (5)
Vite M4, Testa piatta (5)
Ecrou auto-freiné M2.5
Dado autobloccante M2.5, (5)
Accessoires spéciaux
Viteria speciale 1:10 4wd tutti
Fusée avant (2)
Roulements 5x10x4mm (8)
Roulements 10x15x4mm (2)
5x10x4mm Cuscinetto a sfere (8)
10x15x4mm Cuscinetto a sfere (2)
Cuscinetto a sfere 12x18xT4mm,
Roulements 12x18x4mm (4)
(4)
Cuscinetto a sfere 6x12xT4mm,
Roulements 6x12x4mm (4)
(4)
Cuscinetto a sfere 8x14xT4mm,
Roulements 8x14x4mm (4)
(4)
Ruota anter./poster. (2): 1:10 4wd
Jantes av/arr (2)
Torment
Ruota anter./poster. & gomma
Pneus montés sur jantes (2)
premontata (2): Torment
M4 dado autobloccante flagiato
Ecrou auto-freiné épaulé M4 (4)
(4)
Clips de carrosserie (8)
Clips carrozzeria (8)
Moteur à balais
Motore a spazzole
Variateur électronique
ESC per mot. a spazzole
Servo
Servo
Récepteur SR201 2 voies DSM - SR201 2Ch DSM Sport RX car Résine de protection
rivestito
Pare-choc arrière : Torment
1/10 4wd
Carrosserie Grise/Noire :
Torment 1/10 4wd & 2wd
Emetteur DX2E 2 voies DSMR
Set paraurti posteriore: 1:10 4wd
Torment
Carrozzeria, grigio/nera: 1:10 2wd
& 4wd Torment
DX2E 2-Ch DSMR
Radio per auto
TORMENT™
57
®
ECX03013 | ECX03013AU | ECX03013I
www.ecxrc.com
40819
Created 10/2013
© 2014 Horizon Hobby, Inc.
ECX, the ECX logo, Torment, Dynamite, Speedpack, DSM, DSM2 and the
Horizon Hobby logo are trademarks or registered trademarks of Horizon Hobby, Inc.
The Spektrum trademark is used with permission of Bachmann Industries, Inc.