Eljer 015-0309 Specifications

INSTALLATION AND
OPERATION MANUAL
BY AMERICAN STANDARD
WHIRLPOOL, AIR BATHS AND SOAKING TUBS
MODEL NUMBERS:
015-0005
015-0015
015-0026
015-0066
015-0076
015-0077
015-0140
015-0141
015-0142R
015-0142L
015-0143
015-0144
015-0145
015-0146
015-0150
015-0156
015-0305
015-0309
015-2500
015-4800
015-5400
025-0005
025-0140
025-0141
025-0142R
025-0142L
025-0143
025-0144
025-0145
025-0146
025-0155
025-0159
025-2505
025-4805
025-5405
035-0140
035-0141
035-0142R
035-0142L
035-0143
035-0144
035-0145
035-0146
035-0151
035-0158
035-2501
035-5401
045-0140
045-0141
045-0142R
045-0142L
045-0143
045-0145
045-0146
045-0154
045-0157
045-2504
045-4804
045-5404
THANK YOU...
for selecting an Eljer bathing product. Your new bath is shipped to you after careful inspection. The whirlpool
version is completely assembled with pump and circulatory system piping. All you need to finish the installation
are your selected fittings, electrical connections and support bedding material.
To ensure maximum performance and pleasure from this product, please follow the instructions and cautions.
For questions or service issues, please call Technical Support 1-(800)-442-1902.
Please do not contact or return product to the store.
© Eljer 2014
All product names listed herein are trademarks of Eljer unless otherwise noted.
1
754764-100 Rev. C
TABLE OF CONTENTS:
Cover................................................................................................Page 1
Table of Contents..............................................................................Page 2
Safety Instructions Notice.................................................................Page 3
Installation, Framing and Post Installation
Clean-Up Instructions.......................................................................Page 4 - 5
Typical Flange & Under Deck Mounting Instructions........................Page 5 - 6
General Specifications for Whirlpools...............................................Page 7 - 8
Roughing-in References for All Model Series...................................Pages 9 - 17
Electrical Installation Instructions.....................................................Page 18 - 19
Whirlpool and Air Massage
Combination Models........................................................................Page 19
Operating Instructions.......................................................................Page 20
Cleaning and Maintenance...............................................................Page 21
Warranties...........................................................................................Page 22 - 23
754764-100 Rev. C
2
IMPORTANT SAFETY INSTRUCTIONS
INSTRUCTIONS PERTAINING TO
A RISK OF FIRE, ELECTRIC SHOCK
OR INJURY TO PERSONS
READ AND FOLLOW ALL INSTRUCTIONS!
!
WARNING: Risk of personal injury. Do not permit children to use this unit without adult supervision.
!
WARNING: Risk of personal injury. Do not operate this unit without the guard over the suction fitting.
!
WARNING: Risk of electric shock. Do not permit electrical appliances (hair dryer, telephone, radio, etc.) within
60 inches (1524mm) of this unit.
!
WARNING: Risk of hyperthermia and possible drowning. People using medications and/or having adverse
medical history should consult a physician before using this product.
!
WARNING: Risk of personal injury. Do not overfill unit before entering. Entering tub when filled more than 2/3
can cause overflow and slippery conditions. Exercise caution when entering and exiting.
!
WARNING: No Food or Alcoholic Beverages. Use of your bathtub immediately after meals is not
recommended. Avoid alcohol consumption before or during bathing. Alcoholic beverages can cause drowsiness or
hyperthermia resulting in loss of consciousness or even drowning.
!
WARNING: Pregnancy. If you are or think you may be pregnant, consult your physician before using the bathtub.
Never drop or insert any object into any opening.
Use this unit only for its intended use as described in this manual. Do not use any attachments not recommended by
American Standard.
The unit must be connected only to a supply circuit that is properly protected by a ground-fault circuit-interrupter
(GFCI). Such a GFCI should be provided by the installer and should be tested on a routine basis. To test the GFCI,
push the test button. The GFCI should interrupt power. Push the reset button. Power should be restored. If the GFCI
fails to operate in this manner, the GFCI is defective. If the GFCI interrupts power to the bathtub without the test button
being pushed, a ground current is flowing, indicating the possibility of an electric shock. Do not use this hydromassage
bathtub. Disconnect the hydromassage bathtub and have the problem corrected by a licensed electrician before using.
A pressure wire connector is provided on the exterior of the motor unit to permit connection of a no. 8 AWG solid
copper bonding conductor between this unit and all other electrical equipment and exposed metal in the vicinity, as
needed to comply with local requirements. To reduce the risk of an electric shock, connect this connector to the
grounding terminal of your electric service or supply panel with a conductor equivalent in size to the circuit conductors
supplying this unit.
SAVE THESE INSTRUCTIONS
3
754764-100 Rev. C
Installation and Framing Instructions
Each bath arrives ready for installation, completely equipped with the pump and plumbing
necessary for operation. However, a drain/overflow kit is required for each bath and it is
not included.
The variety of installations for this bath may require framing procedures other than those shown.
Locate studs as required. Ensure roughing-in dimensions are proper, plumb, and square.
!
!
Remove the bath from the carton. Retain the shipping carton until satisfactory
inspection of the product has been made. Do not lift the bath by the plumbing at
any time; handle by the shell only.
All bath units are factory tested for proper operation and watertight connections
prior to shipping. Prior to installation and before enclosing with wallboard, tile,
etc., the bath must be filled with water and operated to check for leaks that may
have resulted from shipping damage or mishandling.
!
The sumps of these baths are not supported by the feet and additional sump
support is required. Once the bath is in place, the rim of the bath should contact
the stringer or pier but supports no weight.
!
Provisions must be made in all installations for an access opening for servicing the
bath pump. Unless an access opening of at least 12" x 24" (305mm x 610mm) is
provided, warranty service will not be performed. It is strongly recommended that an
additional opening be provided for access to drain components.
!
Each bath has a nominal length (L), width (W), and Height (H) along with a rim
height. Unless otherwise noted in the following rough-in references, assume
that the nominal tolerances are as much as +/-1/4 inch (6mm). Therefore, it is
strongly recommended that the installer build the surrounding structure after
receiving the actual bath. Structural measurements should be verified against
the actual bath received to ensure proper fit.
POST INSTALLATION CLEAN-UP
Remove all construction debris from bath. Tile grout can be removed with a wooden
popsicle stick or tongue depressor.
Do not use wire brushes or any other metal implement on bath surface.
Post installation clean-up generally can be completed using warm water and liquid
dishwashing detergent.
Stubborn dirt or stains may be removed using granular Spic and Span® mixed with water.
Painter's naphtha can be used to remove excess adhesives and/or wet oil-base paint.
754764-100 Rev. C
4
INSTALLATION AND FRAMING INSTRUCTIONS
The variety of installations possible for this whirlpool may require framing procedures other than those shown. Locate studs as
needed. Ensure roughing-in dimensions are proper, plumb and square. Provisions must be made in all installations for an access
opening for servicing the pump and controls. It is strongly recommended that an additional opening be provided for access to the
drain components. The apron should not be used as the primary access opening.
1. Position the whirlpool into the installation opening and level the deck in both directions, shimming the integral leveling
feet IF necessary. Mark the final position of the underside of the deck by tracing a line on to the studs (see Figure 1).
FIGURE 1
2. Remove the whirlpool and attach a 1 x 4 stringer to the studs, with the top of
the stringer touching the traced line.
!
TYPICAL INSTALLATION
The rim of the bath must not support weight.
3. Install drain components to the whirlpool following the drain installation
instructions. Before replacing your whirlpool for final installation, be certain
that an opening has been provided in the sub-floor for the drain. See the
roughing-in drawing and Table 1 for suggested opening size (shadowed) and
location dimensions. The drain/overflow of the bath extends below the bottom
of the bath. Note that this requires a cutout in the floor.
!
C*
The floor structure beneath the bath must be able to support a total weight of
bath, water, and bather. Refer to Table 1 under total weight for your model.
SEE TABLE 1 ON PAGE 7 - 8.
TILE
The bath must be supported along it’s entire bottom. Use mortar as
bedding material (do not use sand or foam). Apply enough mortar to support
the complete bottom of the bath. After the mortar has been poured, and before it
sets, position whirlpool or bath until the rim is leveled against the leveling
stringers or mounting surfaces (see “Typical Installations”) shown below.
!
WALLBOARD
SEALANT
TILE BEAD
STRIP
BATH
ADHESIVE
The rim of the bath must not support weight. If foundation base is used, allow
the bedding material to completely harden before applying weight to the rim or
bottom of the bath. Any finish material such as tile or wall board must be
self-supporting if it contacts the deck of the bath.
LEVELING STRINGER
1 x 4 (not for support)
NOTE: Tile bead kit not included and
must be purchased separately.
TYPICAL PIER TYPE INSTALLATION
TYPICAL RECESS INSTALLATION
AS DESIRED
F
CUTOUT
G
CUTOUT
C
C
D
12
(305 mm)
W
E
NOTE:
FRONT EDGE
OF BATH MUST
BE SUPPORTED
BY STUD WALL OR
ELJER APRON KIT
12
(305 mm)
AS DESIRED
LEVELING
STRINGERS
MOUNTING
SURFACE
WATERPROOF
SEALANT
24
(610 mm)
ACCESS PANEL MUST BE LOCATED
ON THE SAME SIDE AS THE MOTOR.
BATH
ALLOW OPEN FRAMING ON
PUMP/MOTOR END FOR SERVICE.
ACCESS PANELS NOT REQUIRED
FOR BATH TUBS.
UNLESS AN ACCESS OPENING OF AT LEAST 12" X 24" (305 X 610mm)
IS PROVIDED, WARRANTY SERVICE WILL NOT BE PERFORMED.
24
(610 mm)
ACCESS PANEL MUST BE LOCATED
ON THE SAME SIDE AS THE MOTOR.
ALLOW OPEN FRAMING ON PUMP/MOTOR
END FOR SERVICE.
ACCESS PANELS NOT REQUIRED
FOR BATH TUBS.
UNLESS AN ACCESS OPENING OF AT LEAST 12" X 24" (305 X 610mm)
IS PROVIDED, WARRANTY SERVICE WILL NOT BE PERFORMED.
FOR E & D DIMENSIONS SEE TABLE 1 ON PAGE 7 - 8.
FOR C, G & F DIMENSIONS SEE TABLE 1 ON PAGE 7 - 8.
5
754764-100 Rev. C
TYPICAL FLANGE MOUNTING DETAIL
SUGGESTED WHIRLPOOL / BATH
INSTALLATION METHOD
WOOD
STUDS
TYPICAL INSTALLATION CORNER
STUD
WATERPROOF DRYWALL
OR CEMENT BOARD
TILE
ROOFING NAIL
SEALANT
58-1/2"
(1486mm)
58-1/2"
(1486mm)
LEVELING
STRINGER
12"
(305mm)
TUB
1 x 3 (25 x 76mm) WOOD
STRINGER FULL LENGTH
STEEL
STUDS
STEEL
STUD
WATERPROOF DRYWALL
OR CEMENT BOARD
25"
(635mm)
WASHER
19-1/2"
(495mm)
25"
(635mm)
PUMP ACCESS PANEL
TILE
SEALANT
TUB
4" (102mm)
DRYWALL
SCREW
UNLESS AN ACCESS OPENING OF AT LEAST
12" X 24" (305 X 610mm) IS PROVIDED,
WARRANTY SERVICE WILL NOT BE PERFORMED.
1 x 3 (25 x 76mm) WOOD
STRINGER FULL LENGTH
SECURE THE BATH TO THE STUDS AS SHOWN FOR
WOOD OR STEEL STUD CONSTRUCTION.
754764-100 Rev. C
6
SPECIFICATIONS:
L
W
J
H
SIDE VIEW
C
A
END VIEW
B
DRAIN / OVERFLOW
GENERAL SPECIFICATIONS FOR ELJER WHIRLPOOLS AND BATH TUBS
Description
Dimensions
L-W-H
Drain /
Overflow
Height to
Underside
of Deck: C
Cut Out
Pier
GxF
Rough-In
Recess
ExD
Tub Edge to
Centerline
Overflow: J
Weight with
Water / Floor
Loading
Product
Weight
Gallon to
Overflow
015-0005
5' x 32"
Cypress
L 60" (1524mm)
W 32" (813mm)
H 18-1/2" (469mm)
A 15-1/4"
(387mm)
B 10-1/4"
(260mm)
C 17"
(432mm)
58-1/2"
(1486mm)
x 30-1/2"
(775mm)
60"
(1524mm)
x 30-1/2"
(775mm)
2-1/4"
(57mm)
418 lb. (190 kg)/
31 lb./sq.ft.
(153 kg/sq.m)
98 lb.
(45 kg.)
40
015-0015
5' x 32"
Madison
L 60" (1524mm)
W 32" (813mm)
H 19" (483mm)
A 16-1/4"
(413mm)
B 10-1/4"
(260mm)
C 17-1/2"
(445mm)
58-1/2"
(1486mm)
x 30-1/2"
(775mm)
60"
(1524mm)
x 30-1/2"
(775mm)
2"
(51mm)
418 lb. (190 kg)/
31 lb./sq.ft.
(153 kg/sq.m)
98 lb.
(45 kg.)
40
L 60" (1524mm)
W 36" (914mm)
H 19-3/8" (492mm)
A 16-1/4"
(413mm)
B 8-1/4"
(209mm)
C 17-7/8"
(454mm)
58-1/2"
(1486mm)
x 34-1/2"
(876mm)
60"
(1524mm)
x 34-1/2"
(876mm)
2"
(51mm)
414 lb. (188 kg)/
28 lb./sq.ft.
(135 kg/sq.m)
102 lb.
(46 kg.)
45
015-0066
Triangle
L 60" (1524mm)
W 60" (1524mm)
H 21" (533mm)
A 17"
(432mm)
B 10-1/2"
(267mm)
C 19-1/2"
(495mm)
58-1/2"
(1486mm)
x 58-1/2"
(1486mm)
Not
Applicable
3-1/4"
(83mm)
695 lb. (316 kg)/
34 lb./sq.ft.
(166 kg/sq.m)
119 lb.
(54 kg.)
72
015-0076
6' x 36"
Emblem
L 72" (1829mm)
W 36" (914mm)
H 19-1/2" (495mm)
A 16"
(406mm)
B 10-1/2"
(267mm)
C 18"
(457mm)
70-1/2"
(1791mm)
x 34-1/2"
(876mm)
72"
(1829mm)
x 34-1/2"
(876mm)
1-1/2"
(38mm)
543 lb. (247 kg)/
30 lb./sq.ft.
(148 kg/sq.m)
103 lb.
(47 kg.)
55
015-0077
6' x 36"
Emblem
Total Massage
L 72" (1829mm)
W 36" (914mm)
H 19-1/2" (495mm)
A 16"
(406mm)
B 10-1/2"
(267mm)
C 18"
(457mm)
70-1/2"
(1791mm)
x 34-1/2"
(876mm)
72"
(1829mm)
x 34-1/2"
(876mm)
1-1/2"
(38mm)
559 lb. (254 kg)/
31 lb./sq.ft.
(152 kg/sq.m)
119 lb.
(54 kg.)
55
015-0305/0309
5' x 32"
Patriot
L 60" (1524mm)
W 32" (813mm)
H 18-3/4" (476mm)
A 14"
(356mm)
B 9-1/2"
(241mm)
C 18-1/2"
(469mm)
Not
Applicable
60"
(1524mm)
x 30-1/2"
(775mm)
2-1/4"
(57mm)
455 lb. (207 kg)/
34 lb./sq.ft.
(167 kg/sq.m)
135 lb.
(61 kg.)
40
015-0026
5' x 36"
Canterbury
TABLE 1
(continued on next page)
7
754764-100 Rev. C
SPECIFICATIONS:
L
W
J
H
SIDE VIEW
C
A
END VIEW
B
DRAIN / OVERFLOW
GENERAL SPECIFICATIONS FOR ELJER WHIRLPOOLS AND BATH TUBS
Description
Dimensions
L-W-H
Drain /
Overflow
Height to
Underside
of Deck: C
Cut Out
Pier
GxF
Rough-In
Recess
ExD
025-0005
5' x 32"
Cascada
L 60" (1524mm)
W 32" (813mm)
H 19-1/2" (495mm)
A 15"
(381mm)
B 10-1/4"
(260mm)
C 17"
(432mm)
58-1/2"
(1486mm)
x 30-1/2"
(775mm)
60-1/8"
(1527mm)
x 30-1/2"
(775mm)
025-0140
5' x 32"
LaSalle
L 60" (1524mm)
W 32" (813mm)
H 20" (508mm)
A 16"
(406mm)
B 10-1/2"
(267mm)
C 18-1/2"
(469mm)
58-1/2"
(1486mm)
x 30-1/2"
(775mm)
025-0141
5' x 36"
LaSalle XL
L 72" (1829mm)
W 36" (914mm)
H 21" (533mm)
A 17"
(432mm)
B 10-1/2"
(267mm)
C 19-1/2"
(495mm)
025-0142R
025-0142L
5' x 32"
Cabrillo
L 60" (1524mm)
W 32" (813mm)
H 20-1/2" (520mm)
A 16"
(406mm)
B 10-1/2"
(267mm)
025-0143
60" x 60"
Gemini
L 60" (1524mm)
W 60" (1524mm)
H 21-1/2" (546mm)
025-0144
59-3/4" x 32"
Merrick
Tub Edge to
Centerline
Overflow: J
Weight with
Water / Floor
Loading
Product
Weight
Gallon to
Overflow
2"
(51mm)
425 lb. (193 kg)/
32 lb./sq.ft.
(156 kg/sq.m)
92 lb.
(42 kg.)
40
60-1/8"
(1527mm)
x 30-1/2"
(775mm)
1-3/4"
(44mm)
548 lb. (249 kg)/
41 lb./sq.ft.
(201 kg/sq.m)
90 lb.
(41 kg.)
55
70-1/2"
(1791mm)
x 34-1/2"
(876mm)
72-1/8"
(1832mm)
x 34-1/2"
(876mm)
1-3/4"
(44mm)
862 lb. (392 kg)/
48 lb./sq.ft.
(234 kg/sq.m)
112 lb.
(51 kg.)
90
C 20"
(508mm)
Not
Applicable
60-1/8"
(1527mm)
x 30-1/2"
(775mm)
1-3/4"
(44mm)
699 lb. (318 kg)/
52 lb./sq.ft.
(256 kg/sq.m)
124 lb.
(56 kg.)
69
A 17"
(432mm)
B 10-1/2"
(267mm)
C 20"
(508mm)
58-1/2"
(1486mm)
x 58-1/2"
(1486mm)
Not
Applicable
6-1/4"
(159mm)
863 lb. (392 kg)/
41 lb./sq.ft.
(201 kg/sq.m)
130 lb.
(59 kg.)
88
L 59-3/4" (1518mm)
W 32" (813mm)
H 19-1/4" (489mm)
A 15"
(381mm)
B 10-1/2"
(267mm)
C 18"
(457mm)
58-1/2"
(1486mm)
x 30-1/2"
(775mm)
60-1/8"
(1527mm)
x 30-1/2"
(775mm)
1-3/4"
(44mm)
656 lb. (298 kg)/
49 lb./sq.ft.
(240 kg/sq.m)
90 lb.
(41 kg.)
68
025-0145
6' x 36"
Merrick XL
L 72" (1829mm)
W 36" (914mm)
H 23-3/4" (603mm)
A 19-1/2"
(495mm)
B 9-1/2"
(241mm)
C 22-1/2"
(572mm)
70-1/2"
(1791mm)
x 34-1/2"
(876mm)
72-1/8"
(1832mm)
x 34-1/2"
(876mm)
1-3/4"
(44mm)
1124 lb. (511 kg)/
62 lb./sq.ft.
(306 kg/sq.m)
124 lb.
(58 kg.)
120
025-0146
58" x 38"
Ridgefield
L 58" (1473mm)
W 38" (965mm)
H 23-1/2" (597mm)
A 19-1/2"
(495mm)
B 9-1/2"
(241mm)
C 22"
(559mm)
56"
(1422mm)
x 36"
(914mm)
Not
Applicable
2-3/4"
(70mm)
763 lb. (347 kg)/
62 lb./sq.ft.
(306 kg/sq.m)
97 lb.
(44 kg.)
80
TABLE 1
(continued from previous page)
754764-100 Rev. C
8
ROUGH-IN REFERENCES
MODEL 015-0005
CYPRESS MODEL 015-0005
60"
(1524mm)
0/I
16"
(406mm)
40-1/2"
(1029mm)
32"
(813mm)
19-1/2"
(495mm)
9" x 14" (229 x 356mm)
FLOOR CUTOUT
PROVIDE ACCESS
TO PUMP
10-1/4"
(260mm)
1-1/2"
(38mm)
60"
(1524mm)
32"
(813mm)
19"
(483mm)
17-1/2"
(445mm)
MODEL 015-0015
MADISON MODEL 015-0015
60"
(1524mm)
0/I
16"
(406mm)
40-1/2"
(1029mm)
32"
(813mm)
19-1/2"
(495mm)
9" x 14" (229 x 356mm)
FLOOR CUTOUT
PROVIDE ACCESS
TO PUMP
10-1/4"
(260mm)
1-1/2"
(38mm)
60"
(1524mm)
32"
(813mm)
17-1/2"
(445mm)
9
19"
(483mm)
754764-100 Rev. C
ROUGH-IN REFERENCES
MODEL 015-0026
CANTERBURY MODEL 015-0026
60"
(1524mm)
18"
(457mm)
44-1/2"
(1130mm)
36"
(914mm)
24-1/2"
(622mm)
9" x 14" (229 x 356mm)
FLOOR CUTOUT
PROVIDE ACCESS
TO PUMP
8-1/4"
(209mm)
60"
(1524mm)
1-1/2"
(38mm)
36"
(914mm)
19-1/2"
(495mm)
17-1/2"
(444mm)
TRIANGLE
MODEL
015-0066
MODEL
015-0066
35-1/2"
(902mm)
60"
(1524mm)
PROVIDE ACCESS
TO PUMP
35-1/2"
(902mm)
46"
(1168mm)
25-1/4"
(641mm)
9" x 14" (229 x 356mm)
FLOOR CUTOUT
10-1/2"
(267mm)
0/I
48-5/8"
(1235mm)
1-1/2"
(38mm)
60"
(1524mm)
44"
(1118mm)
19-1/2"
(495mm)
754764-100 Rev. C
10
21"
(533mm)
ROUGH-IN REFERENCES
MODELMODEL
015-00076
EMBLEM
015-0076
EMBLEM TOTAL MASSAGE MODEL 015-0077
72"
(1829mm)
0/I
18"
(457mm)
51-1/2"
(1308mm)
36"
(914mm)
21-1/2"
(546mm)
9" x 14" (229 x 356mm)
FLOOR CUTOUT
PROVIDE ACCESS
TO PUMP
10-1/2"
(267mm)
1-1/2"
(38mm)
72"
(1829mm)
36"
(914mm)
19-1/2"
(495mm)
17-1/2"
(445mm)
PATRIOT MODEL 015-0309 / 0305
(Right hand version shown)
60"
(1524mm)
16"
(406mm)
42"
(1067mm)
32"
(813mm)
18"
(457mm)
9" x 14" (229 x 356mm)
FLOOR CUTOUT
PROVIDE ACCESS
TO PUMP
SERVING ON
ALL INSTALLATIONS
0/I
APRON / SKIRT
60"
(1524mm)
21"
(533mm)
9-1/2"
(241mm)
1" (25mm)
18-3/4"
(476mm)
32"
(813mm)
19-3/4"
2-1/2" (502mm)
(64mm)
1/2" (13mm)
11
754764-100 Rev. C
ROUGH-IN REFERENCES
CABRILLO MODEL 025-0142R/L
38-1/2"
(978mm)
16"
(406mm)
19"
(483mm)
32"
(813mm)
9-1/2"
(241mm)
32"
(813mm)
60"
(1524mm)
20-1/2"
(521mm)
MODEL 025-0005
CASCADA MODEL 025-0005
60"
(1524mm)
0/I
16"
(406mm)
32"
(813mm)
40-1/2"
(1029mm)
19-1/2"
(495mm)
9" x 14" (229 x 356mm)
FLOOR CUTOUT
PROVIDE ACCESS
TO PUMP
10-1/4"
(260mm)
1-1/2"
(38mm)
60"
(1524mm)
32"
(813mm)
17-1/2"
(445mm)
754764-100 Rev. C
12
19"
(483mm)
ROUGH-IN REFERENCES
LASALLE MODEL 025-0140
38-1/2"
(978mm)
16"
(406mm)
20"
(508mm)
32"
(813mm)
9-1/2"
(241mm)
32"
(813mm)
60"
(1524mm)
1-1/2"
(38mm)
20"
(508mm)
LASALLE XL MODEL 025-0141
50-1/2"
(1283mm)
18"
(406mm)
23"
(5814mm)
36"
(914mm)
9-1/2"
(241mm)
36"
(914mm)
72"
(1829mm)
1-1/2"
(38mm)
21"
(533mm)
13
754764-100 Rev. C
ROUGH-IN REFERENCES
MERRICK MODEL 025-0144
7-3/4"
(197mm)
2-3/4"
(69mm)
3"
(76mm)
44-1/2"
(1130mm)
21-1/2"
26"
(546mm) (659mm)
16"
(406mm)
32"
(813mm)
53-3/4"
(1365mm)
3-1/4"
(83mm)
59-3/4"
(1518mm)
32"
(813mm)
1-1/2"
(38mm)
59-3/4"
(1518mm)
19-1/4"
(489mm)
17-1/4"
(438mm)
MERRICK XL MODEL 025-0145
8-1/4"
(209mm)
XX"
(XXmm)
4"
(102mm)
51-1/2"
(1308mm)
26"
30"
(660mm) (762mm)
18"
(457mm)
63-1/2"
(1612mm)
3-1/4"
(83mm)
72"
(1829mm)
32"
(813mm)
20-1/4"
(514mm)
754764-100 Rev. C
1-1/2"
(38mm)
23-3/4"
(603mm)
14
72"
(1829mm)
36"
(914mm)
ROUGH-IN REFERENCES
GEMINI MODEL 025-0143
60"
(1524mm)
60"
(1524mm)
25-7/8"
(657mm)
48-1/4"
(1226mm)
1-1/2"
(38mm)
21-1/2"
19-7/8"
(546mm) (505mm)
RIDGEFIELD MODEL 025-0146
7-3/8"
(187mm)
4"
(102mm)
4"
(102mm)
42-1/2"
(1079mm)
24"
(609mm)
30"
(762mm)
19"
(482mm)
4"
(102mm)
38"
(813mm)
20-1/4"
(514mm)
38"
(965mm)
50"
(1270mm)
58"
(1473mm)
1-1/2"
(38mm)
58"
(1473mm)
20-1/2"
(521mm)
23-1/2"
(597mm)
15
754764-100 Rev. C
ROUGH-IN REFERENCES
VENICE MODEL 025-2505
21"
(533mm)
42"
(1067mm)
Pump
Location
1-1/2"
(38mm)
25-1/2"
(648mm)
P
45"
(1143mm)
10-3/4"
(273mm)
C
36"
(914mm)
P = Pump (Air or Water)
C = Control Panel
72"
(1829mm)
42"
(1067mm)
21-1/2"
(546mm)
23"
(584mm)
GENESIS MODEL 025-5405
40"
(1016mm)
25"
(635mm)
Pump
Location
10"
(254mm)
C
P
2"
(51mm)
48-1/8"
(1232mm)
P = Pump (Air or Water)
C = Control Panel
35-3/4"
(908mm)
71-1/2"
(1816mm)
40"
(1016mm)
20"
(508mm)
754764-100 Rev. C
16
22"
(559mm)
ROUGH-IN REFERENCES
PATRIOT MODEL 025-0155 / 025-0159
16"
(406mm)
42"
(1067mm)
18"
(457mm)
36"
(914mm)
PUMP LOCATION
60"
(1524mm)
1"
(25mm)
21"
(533mm)
36"
(914mm)
18-3/4"
(476mm)
19-3/4"
(502--mm)
1/2"
(13mm)
CASANOVA MODEL 025-4805
36"
(914-mm)
P = PUMP (AIR or WATER)
C = CONTROL PANEL
60"
(1524mm)
34"
(864mm)
P
PUMP LOCATION
1-1/2"
(38mm)
45"
(1143mm)
10-3/8"
(264mm)
C
84-1/2"
(2146mm)
60"
(1524mm)
19-1/2"
(495mm)
21"
(355mm)
42-1/4"
(1073mm)
17
754764-100 Rev. C
ELECTRICAL INSTALLATION INSTRUCTIONS
All wiring must be performed by a licensed electrician in accordance with the national electrical code and all other
applicable codes.
WARNING:
When using electrical products, basic precautions should always be observed, including the following:
1. DANGER: RISK OF ELECTRIC SHOCK
Connect only to a circuit protected by a ground-fault circuit interrupter.
2. Grounding is required. The unit should be installed by a licensed electrician and grounded.
3. Install to permit access for servicing.
4. All building materials and wiring should be routed away from the pump body and heater (if equipped).
AIR SWITCH WHIRLPOOLS
The whirlpool should be installed on a 120 vac, 15 amp dedicated circuit. The circuit should be hard-wired from the
electrical power supply panel. The circuit must be a three (3) wire circuit from the electrical supply panel. A grounded
neutral wire and a third wire, earth ground, are essential. A SEPARATE 15 AMP MAXIMUM GFCI CIRCUIT IS
REQUIRED IF THE OPTIONAL HEATER IS INSTALLED (SEE INSTALLATION INSTRUCTIONS SUPPLIED WITH
THE HEATER MODEL NUMBER – 494-1000).
ELECTRICA L I N S T A L L A T I O N
GFCI
OUTLET
WH I R LPOOL M OU N TED
A I R SWI TC H OR
WA LL TI M ER
B LA C K
WH I TE
120 VAC
PU M P/ M OTOR
GND .
ELECTRICAL DIAGRAM
READ AND FOLLOW ALL INSTRUCTIONS
754764-100 Rev. C
18
ELECTRICAL INSTALLATION INSTRUCTIONS (continued)
WHIRLPOOL PLUS AIR BATH COMBINATIONS
The whirlpool pump and blower should be installed on a 120 vac, 20 amp dedicated circuit. The circuit should be
hard-wired from the electrical power supply panel. The circuit must be a three (3) wire circuit from the electrical supply
panel. A grounded neutral wire and a third wire, earth ground, are essential. A SEPARATE 15 AMP MAXIMUM GFCI
CIRCUIT IS REQUIRED IF THE OPTIONAL HEATER IS INSTALLED (SEE INSTALLATION INSTRUCTIONS
SUPPLIED WITH THE HEATER MODEL NUMBER – 494-1000).
WHIRLPOOL PLUS AIR BATH COMBINATION CIRCUIT WITH OPTIONAL HEATER
CONTROL PAD
PUMP
PUMP
TIMER
CONTROL
PUMP
FLOW
CONTROL
VALVE
BLOWER
VARIABLE
CONTROL
HEATER
ELECTRICAL
FEED
120 V, 60 Hz
15 AMP GFCI
GFCI
120 V, 60 Hz
20 AMP GFCI
GFCI
The Whirlpool plus Air Bath combination control pad contains six (6) buttons.
Three controls on the “Therapy Control Center” operate the whirlpool and the bottom three controls operate the air
system. The whirlpool and air massages systems may be used at the same time if desired.
The air bath is controlled by a three button control:
1. The first button switches the blower on or off. The other features will not operate unless the blower is turned on.
2. The second button sets the power level of the blower. Holding the button depressed will cycle the blower power from
low to high in a continuous cycle. When the desired level is reached, remove your finger quickly from the button to
maintain that power setting.
3. The third button is a three step wave action button. Once activated, the air holes expell air in a slow pulsating flow
called wave action. There are 3 steps or positions for wave strength.
a. Position #1 operates the blower at a steady flow.
b. Position #2 operates the blower at a quick wave action.
c. Position #3 operates the blower at a slower wave action.
Adjusts the variable
water flow of the jets
Switches from
continuous to wave
action water flow
Switches the
jet-pump
on or off
Switches from
continuous to
wave action air flow
Switches the
air blower
on or off
Adjusts the variable
air flow of the blower
WHIRLPOOL PLUS AIR BATH COMBINATION UNITS ARE EQUIPPED WITH AN AUTOMATIC CLEANING
AND PURGE CYCLE
Air Baths have a preprogrammed cleaning and purge cycle built in to expel the remaining water in the air channels. It
activates within 20 minutes after the bath is drained, blows for about 2 to 3 minutes and then shuts off automatically.
There is nothing to be alarmed about if you hear a blowing noise coming from the tub after the tub has been turned off.
The noise you hear is the cleaning cycle in operation.
19
754764-100 Rev. C
OPERATING INSTRUCTIONS
1. Fill the bath to at least 3 inches above the jets before activating the pump.
2. The pump is activated by an on/off switch. Each depression of the button switches the power either on or off.
Do not repeatedly depress the switch in rapid order if you do not see the whirlpool function right away,
as it may take a few seconds before you can see it fully operating.
3. If any factory installed fittings are removed do not operate the unit. A safety hazard may occur.
4. Do not use bubble bath when you operate the whirlpool pump.
This might cause excessive foaming.
5. Both air and whirlpool systems are plumbed in a way that water will
drain from the plumbing easily.
AIR SWITCH
ON-OFF SWITCH
The whirlpool bath pump is activated by a on-off switch. Each depression of the switch
will actuate the pump. If off, one depression will turn the pump on. If on,
the next depression will turn it off.
JET OPERATION AND ADJUSTMENT
The jets can be easily adjusted by pointing the jet-nozzle in the desired direction. For units
with Hydro Jets, the strength of the waterflow and air induction can be regulated through
twisting the jet-nozzle. Twisting the nozzle clockwise will decrease the water flow and finally completely
turn off the water flow of that particular jet. If the nozzle is twisted counter- clockwise then the water
flow will increase up to its maximum flow.
ADJUSTABLE FLOW CLEAN JET™:
The water flow action may be adjusted from vigorous to soft by rotating the nozzle clockwise for vigorous and
counterclockwise for soft.
NOTE: You may balance the air volume control and nozzle adjustment for the most desirable condition.
Large Jet
Small Jet
Softer Massage
(counter-clockwise)
Softer Massage
(counter-clockwise)
More Vigorous Massage
(clockwise)
754764-100 Rev. C
More Vigorous Massage
(clockwise)
20
Your Eljer whirlpool is designed to give you many years of pleasure with reasonable care and maintenance.
Your new acrylic bathtub is tough, durable and easy to care for. The colors have been formulated to match other
Eljer fixtures and enhance your choice of bathroom decorations. The high gloss surface will retain its lasting luster with
proper care and maintenance.
CLEANING AND MAINTENANCE:
• Always fill the tub with temperate water. Excessively hot water (greater than 130˚ F) may cause surface damage.
• Remove bath mat after use and hang to dry. Allowing bath mat to dry in the tub may cause surface damage.
• Clean after use with a mild liquid household detergent cleaner. Do not turn on jets when such cleaners are present.
Do not use: Lestoil® Cleaner; Lysol® Disinfectant (spray or concentrate); or Lysol® Basin, Tub and Tile Cleaner;
Windex® Cleaner; Mr. Clean® Cleaner; Dow® Disinfectant Bathroom Cleaner*; or other cleaning products in
aerosol cans.
HARSH CHEMICALS, SHARP AND ABRASIVE OBJECTS
SHOULD NEVER BE USED ON ACRYLIC SURFACES
• Do not use wire brushes, knives or sharp objects to remove stains or other surface blemishes.
• Use of abrasive cleaners or powders will dull the surface. If the glossy surface loses its sheen, dulled areas can
be partially restored by rubbing with a white automotive body polishing compound and waxing with a liquid wax.
Do not wax surfaces where you walk or stand.
• Do not allow nail polish remover, acetone, dry-cleaning fluid, paint remover, or other solvents to come into contact
with the surface.
• Clean the surrounding surface immediately after using caustic drain cleaners.
Do not permit drain cleaner to enter circulation system.
• Burning cigarettes will irreparably damage the surface of the whirlpool.
CLEANING/PURGING THE CIRCULATION SYSTEM
Once every month the circulating system must be purged and cleaned. Follow the steps outlined below:
1.
Fill whirlpool with warm water and add two teaspoons of powdered automatic dishwasher (not laundry)
detergent and one-half cup of household bleach to filled whirlpool.
2. Activate whirlpool system in accordance with operating instructions and run system for two minutes.
3. Drain and refill whirlpool with cold water. Circulate for five minutes.
4. Drain whirlpool completely after step 3 (above) is completed.
For Troubleshooting and Repair Parts please log on to www.eljer.com
* Lestoil® is a registered trademark of The Clorox Company.
Lysol® is a registered trademark of The Linden Company.
Windex® is a registered trademark of S.C. Johnson and Son, Inc.
Mr. Clean® is a registered trademark of The Proctor and Gamble Company.
Dow® is a registered trademark of The Dow Chemical Company.
21
754764-100 Rev. C
AS AMERICA, INC. LIMITED LIFETIME WARRANTY FOR
ELJER PREMIERE SERIES ACRYLIC TUBS
AS America, Inc. (“American Standard”) warrants to the original consumer purchaser that it will, at its option, repair or replace this
tub or any of its parts that are found by American Standard, in its sole judgment, to be defective under normal residential use and
maintenance so long as it is owned by the original consumer purchaser.
This limited warranty does not apply to commercial installations. The warranty for commercial installations is three (3) years.
THIS WARRANTY SHALL BE VOID IF THE ACCESS PANEL TO THE WHIRLPOOL IS COVERED IN ANY MANNER
CONTRARY TO THE INSTALLATION INSTRUCTIONS. In no event will American Standard be liable for the cost of repair or
replacement of any installation materials including but not limited to tiles, marble etc.
This limited warranty DOES NOT COVER the following:
1. Defects or damages arising from shipping, installation, alterations, accidents, abuse, misuse, lack of proper maintenance and
cleaning as directed in the owner’s manual and use of other than genuine American Standard replacement parts, in all cases
whether caused by a plumbing contractor, service company, the owner or any other person.
2. Deterioration through normal wear and tear and the expense of normal maintenance.
3. Commercial application.
4. Options and accessories. American Standard’s limited warranty on these items is lifetime for parts only, two (2) years for the
heater and five (5) years on labor. This lifetime limited warranty covers accessories manufactured by American Standard
(e.g. aprons, drains, grab bars, trim kits) against defects of material or workmanship. Warranty coverage begins on the date
the accessory was originally purchased by the owner.
5. Postage or shipping costs for returning products for repairs or replacement under this limited warranty and labor or other costs
incurred in connection with product removal or installation under this limited warranty.
6. ANY LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, ALL OF WHICH ARE HEREBY EXPRESSLY
DISCLAIMED, OR THE EXTENSION BEYOND THE DURATION OF THIS LIMITED WARRANTY OF ANY IMPLIED
WARRANTIES, INCLUDING THOSE OF MERCHANTABILITY OR FITNESS FOR AN INTENDED PURPOSE. (Some
jurisdictions do not allow limitations on how long an implied warranty lasts, or the exclusion or limitation of incidental or
consequential damages, so these limitations and exclusions may not apply to you.)
7. Responsibility for compliance with local code requirements. (Since local code requirements vary greatly distributors, retailers,
dealers, installation contractors and users of plumbing products should determine whether there are any code restrictions on
the installation or use of a specific product.)
This limited warranty gives you specific legal rights. You may have other statutory rights that vary from state to state or province to
province, in which case this limited warranty does not affect such statutory rights.
For service under this warranty, it is suggested that a claim be made through the contractor or dealer from or through whom the
product was purchased, or that a service request (including a description of the product model and of the defect) be sent to the
following address:
In the United States:
AS America, Inc.
P.O. Box 6820
Piscataway, New Jersey 08855
Attention: Director of Customer Care
For residents of the United States, warranty
information may also be obtained by calling
the following toll free number: (800) 442-1902
www.eljer.com
754764-100 Rev. C
In Canada:
AS Canada, ULC
5900 Avebury Rd.
Mississauga, Ontario
Canada L5R 3M3
Toll Free: (800) 387-0369
www.eljer.com
22
In Mexico:
American Standard B&K Mexico
S. de R.L. de C.V.
Via Morelos #330
Col. Santa Clara
Ecatepec 55540 Edo. Mexico
Toll Free: 01-800-839-1200
www.eljer.com
AS America, Inc. Limited Lifetime Warranty for Premium Acrylic Air Baths
AS America, Inc. (”American Standard”) warrants to the original consumer purchaser that it will, at its option,
repair or replace this whirlpool or any of its parts that are found by American Standard, in its sole judgment,
to be defective under normal residential use and maintenance so long as it is owned by the original
consumer purchaser.
This warranty shall only become effective upon receipt by American Standard of a completely filled out
Warranty Registration Card evidencing proof of purchase.
This limited warranty does not apply to commercial installations. The warranty for commercial installations is
three (3) years.
THIS WARRANTY SHALL BE VOID IF THE ACCESS PANEL TO THE WHIRLPOOL IS COVERED IN ANY
MANNER CONTRARY TO THE INSTALLATION INSTRUCTIONS. In no event will American Standard be
liable for the cost of repair or replacement of any installation materials including but not limited to tiles,
marble etc.
This limited warranty DOES NOT COVER the following:
1. Defects or damages arising from shipping, installation, alterations, accidents, abuse, misuse, lack of
proper maintenance and cleaning as directed in the owner’s manual and use of other than genuine
American Standard replacement parts, in all cases whether caused by a plumbing contractor, service
company, the owner or any other person.
2. Deterioration through normal wear and tear and the expense of normal maintenance.
3. Commercial application.
4. Options and accessories. American Standard’s limited warranty on these items is one year for parts only
and excludes labor. This one year limited warranty covers accessories manufactured by American
Standard (e.g. aprons, drains, grab bars, heaters, trim kits) against defects of material or workmanship.
Warranty coverage begins on the date the accessory was originally purchased by the owner.
5. Postage or shipping costs for returning products for repairs or replacement under this limited warranty and
labor or other costs incurred in connection with product removal or installation under this limited warranty.
6. ANY LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, ALL OF WHICH ARE HEREBY
EXPRESSLY DISCLAIMED, OR THE EXTENSION BEYOND THE DURATION OF THIS LIMITED
WARRANTY OF ANY IMPLIED WARRANTIES, INCLUDING THOSE OF MERCHANTABILITY OR
FITNESS FOR AN INTENDED PURPOSE. (Some jurisdictions do not allow limitations on how long an
implied warranty lasts, or the exclusion or limitation of incidental or consequential damages, so these
limitations and exclusions may not apply to you.)
7. Responsibility for compliance with local code requirements. (Since local code requirements vary greatly
distributors, retailers, dealers, installation contractors and users of plumbing products should determine
whether there are any code restrictions on the installation or use of a specific product.)
This warranty gives you specific legal rights. You may have other legal rights that vary from state to state.
For service under this warranty, you should contact the following:
In the United States:
American Standard Brands
P.O. Box 6820
Piscataway, New Jersey 08855
Attention: Director of Customer Care
For residents of the United States, warranty
information may also be obtained by calling
the following toll free number: (800) 442-1902
www.americanstandard.com
In Canada:
AS Canada, ULC
5900 Avebury Rd.
Mississauga, Ontario
Canada L5R 3M3
Toll Free: (800) 387-0369
www.americanstandard.ca
23
In Mexico:
American Standard B&K Mexico
S. de R.L. de C.V.
Via Morelos #330
Col. Santa Clara
Ecatepec 55540 Edo. Mexico
Toll Free: 01-800-839-1200
www.americanstandard.com.mx
754764-100 Rev. C