Barco R9000740 Installation manual

BARCO PROJECTION SYSTEMS
BARCO PROJECTION SYSTEMS
VISION
701 MULTIMEDIA
VISION
701 MULTIMEDIA
R9000740
R9000740
INSTALLATION MANUAL
INSTALLATION MANUAL
Date:
070597
Rev. :
01
Art. No.
R5975248
Date:
070597
Rev. :
01
Art. No.
R5975248
Due to constant research, the information in this manual is subject to
change without notice.
Due to constant research, the information in this manual is subject to
change without notice.
Produced by BARCO NV, May 1997.
All rights reserved.
Produced by BARCO NV, May 1997.
All rights reserved.
Trademarks are the rights of their respective owners.
Trademarks are the rights of their respective owners.
BARCO nv/Projection Systems
Noordlaan 5
8520 Kuurne
Belgium
BARCO nv/Projection Systems
Noordlaan 5
8520 Kuurne
Belgium
Printed in Belgium
Printed in Belgium
WARNINGS ......................................................................................................... 1-1
SAFETY INSTRUCTIONS .................................................................................... 1-1
On safety ....................................................................................................... 1-4
On installation ............................................................................................... 1-5
On servicing .................................................................................................. 1-6
On cleaning ................................................................................................... 1-6
On repacking ................................................................................................. 1-7
On illumination .............................................................................................. 1-7
WARNINGS ......................................................................................................... 1-1
SAFETY INSTRUCTIONS .................................................................................... 1-1
On safety ...................................................................................................... 1-4
On installation ............................................................................................... 1-5
On servicing .................................................................................................. 1-6
On cleaning ................................................................................................... 1-6
On repacking ................................................................................................. 1-7
On illumination .............................................................................................. 1-7
UNPACKING & DIMENSIONS ............................................................................. 2-1
Unpacking ..................................................................................................... 2-2
Projector dimensions ..................................................................................... 2-3
UNPACKING & DIMENSIONS ............................................................................. 2-1
Unpacking ..................................................................................................... 2-2
Projector dimensions ..................................................................................... 2-3
INSTALLATION GUIDELINES .............................................................................. 3-1
* Environment ................................................................................................ 3-2
* What about ambient light ? .......................................................................... 3-2
* Which screen type? ..................................................................................... 3-3
* What image size? How big should the image be? ....................................... 3-3
* Where to install the projector? ..................................................................... 3-4
* How to install the projector? ......................................................................... 3-6
INSTALLATION GUIDELINES ............................................................................. 3-1
* Environment ............................................................................................... 3-2
* What about ambient light ? .......................................................................... 3-2
* Which screen type? .................................................................................... 3-3
* What image size? How big should the image be? ...................................... 3-3
* Where to install the projector? ..................................................................... 3-4
* How to install the projector? ......................................................................... 3-6
INSTALLATION SET UP ...................................................................................... 4-1
Access to controls ......................................................................................... 4-2
Scan adaptation ............................................................................................ 4-4
INSTALLATION SET UP ...................................................................................... 4-1
Access to controls ......................................................................................... 4-2
Scan adaptation ............................................................................................ 4-4
PROJECTOR SET UP ......................................................................................... 5-1
Projector Set Up ............................................................................................. 5-2
Password mode ............................................................................................. 5-3
PROJECTOR SET UP ......................................................................................... 5-1
Projector Set Up ............................................................................................ 5-2
Password mode ............................................................................................. 5-3
POWER (MAINS) CONNECTION ......................................................................... 6-1
Input power (mains) voltage adaptation. ........................................................ 6-2
Power (mains) cord connection ..................................................................... 6-2
Fuses ............................................................................................................ 6-4
Switching on/off ............................................................................................. 6-5
POWER (MAINS) CONNECTION ........................................................................ 6-1
Input power (mains) voltage adaptation. ........................................................ 6-2
Power (mains) cord connection ..................................................................... 6-2
Fuses ............................................................................................................ 6-4
Switching on/off ............................................................................................. 6-5
INSTALLATION ADJUSTMENTS ......................................................................... 7-1
Entering the adjustment mode ....................................................................... 7-2
Overview flow chart installation mode. ........................................................... 7-3
Installation mode start up .............................................................................. 7-4
Scheimpfug adjustment ................................................................................. 7-8
Optical lens focusing ................................................................................... 7-10
Electrical focusing ....................................................................................... 7-11
Raster centering .......................................................................................... 7-12
CRT projection angle adjustment ................................................................. 7-14
Alignment of the projector. ........................................................................... 7-18
INSTALLATION ADJUSTMENTS ......................................................................... 7-1
Entering the adjustment mode ....................................................................... 7-2
Overview flow chart installation mode. ........................................................... 7-3
Installation mode start up .............................................................................. 7-4
Scheimpfug adjustment ................................................................................. 7-8
Optical lens focusing ................................................................................... 7-10
Electrical focusing ....................................................................................... 7-11
Raster centering .......................................................................................... 7-12
CRT projection angle adjustment ................................................................. 7-14
Alignment of the projector. ........................................................................... 7-18
Appendix A : Ceiling mount kit for 700 projectors. ................................................... A-1
Appendix B : G2 adjustment .................................................................................. B-1
5975248 BARCOVISION 701 MULTIMEDIA 070597
i-I
Appendix A : Ceiling mount kit for 700 projectors. ................................................... A-1
Appendix B : G2 adjustment .................................................................................. B-1
5975248 BARCOVISION 701 MULTIMEDIA 070597
TABLE OF CONTENTS
TABLE OF CONTENTS
TABLE OF CONTENTS
TABLE OF CONTENTS
i-I
TABLE OF CONTENTS
TABLE OF CONTENTS
TABLE OF CONTENTS
i-II
TABLE OF CONTENTS
5975248 BARCOVISION 701 MULTIMEDIA 070597
i-II
5975248 BARCOVISION 701 MULTIMEDIA 070597
SAFETY INSTRUCTIONS
WARNINGS
WARNINGS
SAFETY INSTRUCTIONS
SAFETY INSTRUCTIONS
on safety
on installation
on installation
on servicing
on servicing
on cleaning
on repacking
on illumination
5975248 BARCOVISION 701 MULTIMEDIA 090497
SAFETY INSTRUCTIONS
on safety
1-1
on cleaning
on repacking
on illumination
5975248 BARCOVISION 701 MULTIMEDIA 090497
SAFETY INSTRUCTIONS
SAFETY INSTRUCTIONS
1-1
SAFETY INSTRUCTIONS
SAFETY INSTRUCTIONS
Notice on Safety
Notice on Safety
This equipment is built in accordance with the requirements of the international safety
standards EN60950, UL 1950 and CSA C22.2 No.950, which are the safety standards
of information technology equipment including electrical business equipment.
This equipment is built in accordance with the requirements of the international safety
standards EN60950, UL 1950 and CSA C22.2 No.950, which are the safety standards
of information technology equipment including electrical business equipment.
These safety standards impose important requirements on the use of safety critical
components, materials and isolation, in order to protect the user or operator against risk
of electric shock and energy hazard, and having access to live parts.
Safety standards also impose limits to the internal and external temperature rises,
radiation levels, mechanical stability and strength, enclosure construction and protection against the risk of fire.
These safety standards impose important requirements on the use of safety critical
components, materials and isolation, in order to protect the user or operator against
risk of electric shock and energy hazard, and having access to live parts.
Safety standards also impose limits to the internal and external temperature rises,
radiation levels, mechanical stability and strength, enclosure construction and protection against the risk of fire.
Simulated single fault condition testing ensures the safety of the equipment to the user
even when the equipment's normal operation fails.
Simulated single fault condition testing ensures the safety of the equipment to the user
even when the equipment's normal operation fails.
INSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS
Before operating your projector please read this manual thoroughly, and
retain it for future reference.
Before operating your projector please read this manual thoroughly, and
retain it for future reference.
Installation and preliminary adjustments should be performed by qualified
BARCO personnel or by authorized BARCO service dealers.
Installation and preliminary adjustments should be performed by qualified
BARCO personnel or by authorized BARCO service dealers.
OWNER’S RECORD
OWNER’S RECORD
PART NUMBER:
SER. NUMBER:
DEALER:
5975248 BARCOVISION 701 MULTIMEDIA 090497
SAFETY INSTRUCTIONS
SAFETY INSTRUCTIONS
1-2
The part number and serial number are located at the left side of the projector. Record
these numbers in the spaces provided below. Refer to them whenever you call upon
your BARCO dealer regarding this product.
1-2
The part number and serial number are located at the left side of the projector.
Record these numbers in the spaces provided below. Refer to them whenever you
call upon your BARCO dealer regarding this product.
PART NUMBER:
SER. NUMBER:
DEALER:
5975248 BARCOVISION 701 MULTIMEDIA 090497
SAFETY INSTRUCTIONS
SAFETY INSTRUCTIONS
The lightning flash with an arrowhead within a triangle is
intended to tell the user that parts inside this product may cause
a risk of electrical shock to persons.
The lightning flash with an arrowhead within a triangle is intended
to tell the user that parts inside this product may cause a risk of
electrical shock to persons.
The exclamation point within a triangle is intended to tell the
user that important operating and/or servicing instructions are
included in the technical documentation for this equipment.
The exclamation point within a triangle is intended to tell the user
that important operating and/or servicing instructions are included in the technical documentation for this equipment.
WARNING
TO PREVENT FIRE OR ELECTRICAL SHOCK HAZARD, DO
NOT EXPOSE THIS PROJECTOR TO RAIN OR MOISTURE
FEDERAL COMMUNICATION COMMISSION (FCC STATEMENT)
This equipment has been tested and found to comply with the limits of a class A
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his
own expense.
This equipment has been tested and found to comply with the limits of a class A
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his
own expense.
5975248 BARCOVISION 701 MULTIMEDIA 090497
SAFETY INSTRUCTIONS
FEDERAL COMMUNICATION COMMISSION (FCC STATEMENT)
1-3
5975248 BARCOVISION 701 MULTIMEDIA 090497
SAFETY INSTRUCTIONS
WARNING
TO PREVENT FIRE OR ELECTRICAL SHOCK HAZARD, DO
NOT EXPOSE THIS PROJECTOR TO RAIN OR MOISTURE
1-3
SAFETY INSTRUCTIONS
SAFETY INSTRUCTIONS
* All the safety and operating instructions should be read before using this unit.
* All the safety and operating instructions should be read before using this unit.
* The safety and operating instructions manual should be retained for future reference.
* The safety and operating instructions manual should be retained for future reference.
* All warnings on the projector and in the documentation manuals should be adhered
to.
* All warnings on the projector and in the documentation manuals should be adhered
to.
* All instructions for operating and use of this equipment must be followed precisely.
* All instructions for operating and use of this equipment must be followed precisely.
On safety
On safety
1. This product should be operated from an AC power source
1. This product should be operated from an AC power source
Operating AC power voltage of the projector when leaving the factory:
Operating AC power voltage of the projector when leaving the factory:
BARCOVISION 701 MULTIMEDIA
Art.No. R9000740 (230V AC)
BARCOVISION 701 MULTIMEDIA
Art.No. R9000740 (230V AC)
The projector leaves the factory for 230 Vac. Consult your dealer to switch over to
120 VAC.
If you are not sure of the type of AC power available, consult your dealer or local
power company.
The projector leaves the factory for 230 Vac. Consult your dealer to switch over to
120 VAC.
If you are not sure of the type of AC power available, consult your dealer or local
power company.
2. This product is equipped with a 3-wire grounding plug, a plug having a third
(grounding) pin. This plug will only fit into a grounding-type power outlet. This is a
safety feature. If you are unable to insert the plug into the outlet, contact your electrician
to replace your obsolete outlet. Do not defeat the purpose of the grounding-type plug.
2. This product is equipped with a 3-wire grounding plug, a plug having a third
(grounding) pin. This plug will only fit into a grounding-type power outlet. This is a
safety feature. If you are unable to insert the plug into the outlet, contact your electrician
to replace your obsolete outlet. Do not defeat the purpose of the grounding-type plug.
WARNING FOR THE CUSTOMERS: THIS APPARATUS MUST BE GROUNDED
(EARTHED) via the supplied 3 conductor AC power cable.
(If the supplied power cable is not the correct one, consult your dealer.)
WARNING FOR THE CUSTOMERS: THIS APPARATUS MUST BE GROUNDED
(EARTHED) via the supplied 3 conductor AC power cable.
(If the supplied power cable is not the correct one, consult your dealer.)
A. Mains lead (AC Power cord) with CEE 7 plug:
A. Mains lead (AC Power cord) with CEE 7 plug:
The colors of the mains lead are colored in
accordance with the following code:
Earth (safety earth)
Neutral
Line (Live)
5975248 BARCOVISION 701 MULTIMEDIA 090497
SAFETY INSTRUCTIONS
SAFETY INSTRUCTIONS
1-4
Green-and-yellow:
Blue:
Brown:
The colors of the mains lead are colored in
accordance with the following code:
1-4
Green-and-yellow:
Blue:
Brown:
Earth (safety earth)
Neutral
Line (Live)
5975248 BARCOVISION 701 MULTIMEDIA 090497
SAFETY INSTRUCTIONS
SAFETY INSTRUCTIONS
B. Power cord with ANSI 73.11 plug:
B. Power cord with ANSI 73.11 plug:
The wires of the power cord are colored in accordance with the following code.
The wires of the power cord are colored in
accordance with the following code.
Green/yellow: ground
White:
neutral
Black:
line (live)
3. Do not allow anything to rest on the power cord. Do not locate this product where
persons will walk on the cord.
To disconnect the cord, pull it out by the plug. Never pull the cord itself.
To disconnect the cord, pull it out by the plug. Never pull the cord itself.
4. If an extension cord is used with this product, make sure that the total of the ampere
ratings on the products plugged into the extension cord does not exceed the extension
cord ampere rating. Also make sure that the total of all products plugged into the wall
outlet does not exceed 15 amperes.
4. If an extension cord is used with this product, make sure that the total of the ampere
ratings on the products plugged into the extension cord does not exceed the extension
cord ampere rating. Also make sure that the total of all products plugged into the wall
outlet does not exceed 15 amperes.
5. Never push objects of any kind into this product through cabinet slots as they may
touch dangerous voltage points or short out parts that could result in a risk of fire or
electrical shock.
5. Never push objects of any kind into this product through cabinet slots as they may
touch dangerous voltage points or short out parts that could result in a risk of fire or
electrical shock.
Never spill liquid of any kind on the product. Should any liquid or solid object fall into
the cabinet, unplug the set and have it checked by qualified service personnel before
resuming operations.
Never spill liquid of any kind on the product. Should any liquid or solid object fall into
the cabinet, unplug the set and have it checked by qualified service personnel before
resuming operations.
6. Lightning - For added protection for this video product during a lightning storm, or
when it is left unattended and unused for long periods of time, unplug it from the wall
outlet. This will prevent damage to the projector due to lightning and AC power-line
surges.
6. Lightning - For added protection for this video product during a lightning storm, or
when it is left unattended and unused for long periods of time, unplug it from the wall
outlet. This will prevent damage to the projector due to lightning and AC power-line
surges.
On installation
On installation
1. Do not place this equipment on an unstable cart, stand, or table. The equipment
may fall, causing serious damage to it.
2. Do not use this equipment near water.
3. Slots and openings in the cabinet and the back or bottom are provided for
ventilation; to ensure reliable operation of the projector and to protect it from
overheating, these openings must not be blocked or covered. The openings should
never be blocked by placing the product on a bed, sofa, rug, or other similar surface.
5975248 BARCOVISION 701 MULTIMEDIA 090497
SAFETY INSTRUCTIONS
3. Do not allow anything to rest on the power cord. Do not locate this product where
persons will walk on the cord.
1-5
1. Do not place this equipment on an unstable cart, stand, or table. The equipment
may fall, causing serious damage to it.
2. Do not use this equipment near water.
3. Slots and openings in the cabinet and the back or bottom are provided for
ventilation; to ensure reliable operation of the projector and to protect it from
overheating, these openings must not be blocked or covered. The openings should
never be blocked by placing the product on a bed, sofa, rug, or other similar surface.
5975248 BARCOVISION 701 MULTIMEDIA 090497
SAFETY INSTRUCTIONS
Green/yellow: ground
White:
neutral
Black:
line (live)
1-5
SAFETY INSTRUCTIONS
SAFETY INSTRUCTIONS
This product should never be placed near or over a radiator or heat register. This
projector should not be placed in a built-in installation or enclosure unless proper
ventillation is provided.
On servicing
On servicing
Do not attempt to service this equipment yourself, as opening or removing covers
may expose you to dangerous voltage potentials and risk of electric shock!
Refer all sevicing to qualified service personnel.
Do not attempt to service this equipment yourself, as opening or removing covers
may expose you to dangerous voltage potentials and risk of electric shock!
Refer all sevicing to qualified service personnel.
Unplug this product from the wall outlet and refer servicing to qualified service
personnel under the following conditions:
Unplug this product from the wall outlet and refer servicing to qualified service
personnel under the following conditions:
a. When the power cord or plug is damaged or frayed.
a. When the power cord or plug is damaged or frayed.
b. If liquid has been spilled into the projector.
b. If liquid has been spilled into the projector.
c.If the product has been exposed to rain or water.
c.If the product has been exposed to rain or water.
d. If the product does not operate normally when the operating instructions are
followed. Note :
Adjust only those controls that are covered by the operating instructions since
improper adjustment of the other controls may result in damage and will often require
extensive work by a qualified technician to restore the product to normal operation.
d. If the product does not operate normally when the operating instructions are
followed. Note :
Adjust only those controls that are covered by the operating instructions since
improper adjustment of the other controls may result in damage and will often require
extensive work by a qualified technician to restore the product to normal operation.
e. If the product has been dropped or the cabinet has been damaged.
e. If the product has been dropped or the cabinet has been damaged.
f. If the product exibits a distinct change in performance, indicating a need for service.
f. If the product exibits a distinct change in performance, indicating a need for service.
Replacement parts - When replacement parts are required, be sure the service
technician has used original BARCO replacement parts or authorized replacement
parts which have the same characteristics as the BARCO original part. Unauthorized
substitutions may result in degraded performance and reliability, fire, electric shock or
other hazards. Unauthorized substitutions may void warranty.
Replacement parts - When replacement parts are required, be sure the service
technician has used original BARCO replacement parts or authorized replacement
parts which have the same characteristics as the BARCO original part. Unauthorized
substitutions may result in degraded performance and reliability, fire, electric shock or
other hazards. Unauthorized substitutions may void warranty.
Safety check - Upon completion of any service or repairs to this projector, ask the
service technician to perform safety checks to determine that the projector is in proper
operating condition.
Safety check - Upon completion of any service or repairs to this projector, ask the
service technician to perform safety checks to determine that the projector is in proper
operating condition.
On cleaning
Unplug this product from the wall outlet before cleaning. Do not use liquid
cleaners or aerosol cleaners. Use a damp cloth for cleaning.
- To keep the cabinet looking brand-new, periodically clean it with a soft cloth.
Stubborn stains may be removed with a cloth lightly dampened with mild detergent
solution. Never use strong solvents, such as thinner or benzine, or abrasive
cleaners, since these will damage the cabinet.
5975248 BARCOVISION 701 MULTIMEDIA 090497
SAFETY INSTRUCTIONS
SAFETY INSTRUCTIONS
1-6
This product should never be placed near or over a radiator or heat register. This
projector should not be placed in a built-in installation or enclosure unless proper
ventillation is provided.
1-6
On cleaning
Unplug this product from the wall outlet before cleaning. Do not use liquid
cleaners or aerosol cleaners. Use a damp cloth for cleaning.
- To keep the cabinet looking brand-new, periodically clean it with a soft cloth.
Stubborn stains may be removed with a cloth lightly dampened with mild detergent
solution. Never use strong solvents, such as thinner or benzine, or abrasive
cleaners, since these will damage the cabinet.
5975248 BARCOVISION 701 MULTIMEDIA 090497
SAFETY INSTRUCTIONS
SAFETY INSTRUCTIONS
- To ensure the highest optical performance and resolution, the projection lenses are
specially treated with an anti-reflective coating, therefore, avoid touching the lens.
To remove dust on the lens, use a soft dry cloth. Do not use a damp cloth, detergent
solution, or thinner.
On repacking
On repacking
Save the original shipping carton and packing material; they will come in handy if you
ever have to ship your equipment. For maximum protection, repack your set as it was
originally packed at the factory.
Save the original shipping carton and packing material; they will come in handy if you
ever have to ship your equipment. For maximum protection, repack your set as it was
originally packed at the factory.
On illumination
On illumination
In order to obtain the best quality for the projected image, it is essential that the ambient
light which is allowed to fall on the screen be kept to an absolute minimum.
In order to obtain the best quality for the projected image, it is essential that the ambient
light which is allowed to fall on the screen be kept to an absolute minimum.
When installing the projector and screen, care must be taken to avoid exposure to
ambient light directly on the screen. Avoid adverse illumination on the screen from
direct sunlight or florescent lighting fixtures.
When installing the projector and screen, care must be taken to avoid exposure to
ambient light directly on the screen. Avoid adverse illumination on the screen from
direct sunlight or florescent lighting fixtures.
The use of controlled ambient lighting, such as incandescent spot light or a dimmer,
is recommended for proper room illumination. Where possible, care should also be
taken to ensure that the floors and walls of the room in which the projector is to be
installed are non-reflecting, dark surfaces. Brighter surfaces will tend to reflect and
diffuse the ambient light and hence reduce the contrast of the projected image on the
screen.
The use of controlled ambient lighting, such as incandescent spot light or a dimmer,
is recommended for proper room illumination. Where possible, care should also be
taken to ensure that the floors and walls of the room in which the projector is to be
installed are non-reflecting, dark surfaces. Brighter surfaces will tend to reflect and
diffuse the ambient light and hence reduce the contrast of the projected image on the
screen.
SAFETY INSTRUCTIONS
SAFETY INSTRUCTIONS
- To ensure the highest optical performance and resolution, the projection lenses are
specially treated with an anti-reflective coating, therefore, avoid touching the lens.
To remove dust on the lens, use a soft dry cloth. Do not use a damp cloth, detergent
solution, or thinner.
5975248 BARCOVISION 701 MULTIMEDIA 090497
1-7
5975248 BARCOVISION 701 MULTIMEDIA 090497
1-7
SAFETY INSTRUCTIONS
SAFETY INSTRUCTIONS
SAFETY INSTRUCTIONS
SAFETY INSTRUCTIONS
1-8
5975248 BARCOVISION 701 MULTIMEDIA 090497
1-8
5975248 BARCOVISION 701 MULTIMEDIA 090497
UNPACKING AND DIMENSIONS
UNPACKING AND DIMENSIONS
UNPACKING
5975248 BARCOVISION 701 MULTIMEDIA 090797
2-1
DIMENSIONS
5975248 BARCOVISION 701 MULTIMEDIA 090797
UNPACKING AND DIMENSIONS
UNPACKING AND DIMENSIONS
DIMENSIONS
UNPACKING
2-1
UNPACKING AND DIMENSIONS
UNPACKING AND DIMENSIONS
Unpacking
To open de banding, pull on the clip as shown in the first drawing.
To open de banding, pull on the clip as shown in the first drawing.
Take the projector out of its shipping carton and place it on a table.
Save the original shipping carton and packing material, they will come in handy if you
ever have to ship your projector. For maximum protection, repack your projector as
it was originally packed at the factory.
Take the projector out of its shipping carton and place it on a table.
Save the original shipping carton and packing material, they will come in handy if you
ever have to ship your projector. For maximum protection, repack your projector as
it was originally packed at the factory.
Contents of the shipped box :
- 1 BARCOVISION 701 MULTIMEDIA.
- 1 remote control + 9V battery
- 1 power cable with outlet plug type CEE7 or ANSI 73.11.
- 1 owner's manual.
- 1 installation manual.
5975248 BARCOVISION 701 MULTIMEDIA 090797
UNPACKING AND DIMENSIONS
UNPACKING AND DIMENSIONS
2-2
Unpacking
2-2
Contents of the shipped box :
- 1 BARCOVISION 701 MULTIMEDIA.
- 1 remote control + 9V battery
- 1 power cable with outlet plug type CEE7 or ANSI 73.11.
- 1 owner's manual.
- 1 installation manual.
5975248 BARCOVISION 701 MULTIMEDIA 090797
UNPACKING AND DIMENSIONS
UNPACKING AND DIMENSIONS
UNPACKING AND DIMENSIONS
Projector dimensions
UNPACKING AND DIMENSIONS
Projector dimensions
5975248 BARCOVISION 701 MULTIMEDIA 090797
2-3
5975248 BARCOVISION 701 MULTIMEDIA 090797
2-3
UNPACKING AND DIMENSIONS
UNPACKING AND DIMENSIONS
UNPACKING AND DIMENSIONS
2-4
UNPACKING AND DIMENSIONS
5975248 BARCOVISION 701 MULTIMEDIA 090797
2-4
5975248 BARCOVISION 701 MULTIMEDIA 090797
INSTALLATION GUIDELINES
INSTALLATION GUIDELINES
INSTALLATION GUIDELINES
Environment
What about ambient light?
What about ambient light?
Which screen type?
Which screen type?
What image size? How big should the image be?
What image size? How big should the image be?
Where to install the projector?
How to install the projector?
5975248 BARCOVISION 701 MULTIMEDIA 090797
INSTALLATION GUIDELINES
Environment
3-1
Where to install the projector?
How to install the projector?
5975248 BARCOVISION 701 MULTIMEDIA 090797
INSTALLATION GUIDELINES
INSTALLATION GUIDELINES
3-1
INSTALLATION GUIDELINES
INSTALLATION GUIDELINES
Installation guidelines
Installation guidelines
Careful consideration of things such as image size, ambient light level, projector placement
and type of screen to use are critical to the optimum use of the projection system.
Careful consideration of things such as image size, ambient light level, projector placement
and type of screen to use are critical to the optimum use of the projection system.
* Environment
* Environment
Do not install the projection system in a site near heat sources such as radiators or
air ducts, or in a place subject to direct sunlight, excessive dust or humidity. Be
aware that room heat rises to the ceiling; check that the temperature near the
installation site is not excessive.
Do not install the projection system in a site near heat sources such as radiators or
air ducts, or in a place subject to direct sunlight, excessive dust or humidity. Be
aware that room heat rises to the ceiling; check that the temperature near the
installation site is not excessive.
* What about ambient light ?
The ambient light level of any room is made up of direct or indirect sunlight and the
light fixtures in the room. The amount of ambient light will determine how bright the
image will appear. So, avoid direct light on the screen.
Windows that face the screen should be covered by opaque drapery while the set is
being viewed. It is desirable to install the projecting system in a room whose walls and
floor are of non-reflecting material. The use of recessed ceiling lights and a method
of dimming those lights to an acceptable level is also important. Too much ambient
light results in a ‘wash out’ of the projected image. This appears as less contrast
between the darkest and lightest parts of the image. With bigger screens, the ‘wash
out’ becomes more important. As a general rule, darken the room to the point where
there is just sufficient light to read or write comfortably. Spot lighting is desirable for
illuminating small areas so that interference with the screen is minimal.
5975248 BARCOVISION 701 MULTIMEDIA 090797
INSTALLATION GUIDELINES
INSTALLATION GUIDELINES
3-2
* What about ambient light ?
3-2
The ambient light level of any room is made up of direct or indirect sunlight and the
light fixtures in the room. The amount of ambient light will determine how bright the
image will appear. So, avoid direct light on the screen.
Windows that face the screen should be covered by opaque drapery while the set is
being viewed. It is desirable to install the projecting system in a room whose walls and
floor are of non-reflecting material. The use of recessed ceiling lights and a method
of dimming those lights to an acceptable level is also important. Too much ambient
light results in a ‘wash out’ of the projected image. This appears as less contrast
between the darkest and lightest parts of the image. With bigger screens, the ‘wash
out’ becomes more important. As a general rule, darken the room to the point where
there is just sufficient light to read or write comfortably. Spot lighting is desirable for
illuminating small areas so that interference with the screen is minimal.
5975248 BARCOVISION 701 MULTIMEDIA 090797
INSTALLATION GUIDELINES
INSTALLATION GUIDELINES
* Which screen type?
* Which screen type?
There are two major categories of screens used for projection equipment. Those used
for front projected images and those for rear projection applications.
There are two major categories of screens used for projection equipment. Those used
for front projected images and those for rear projection applications.
Screens are rated by how much light they reflect (or transmit in the case of rear
projection systems) given a determined amount of light projected toward them. The
‘GAIN’ of a screen is the term used. Front and rear screens are both rated in terms
of gain. The gain of screens range from a white matte screen with a gain of 1 (x1) to
a brushed aluminized screen with a gain of 10 (x10) or more. The choice between
higher and lower gain screens is largely a matter of personal preference and another
consideration called the Viewing angle.
Screens are rated by how much light they reflect (or transmit in the case of rear
projection systems) given a determined amount of light projected toward them. The
‘GAIN’ of a screen is the term used. Front and rear screens are both rated in terms
of gain. The gain of screens range from a white matte screen with a gain of 1 (x1) to
a brushed aluminized screen with a gain of 10 (x10) or more. The choice between
higher and lower gain screens is largely a matter of personal preference and another
consideration called the Viewing angle.
In considering the type of screen to choose, determine where the viewers will be
located and go for the highest gain screen possible. A high gain screen will provide
a brighter picture but reduce the viewing angle.
In considering the type of screen to choose, determine where the viewers will be
located and go for the highest gain screen possible. A high gain screen will provide
a brighter picture but reduce the viewing angle.
For more information about screens, contact your local screen supplier.
For more information about screens, contact your local screen supplier.
Screen width
The BARCOVISION 701 MULTIMEDIA is designed for projecting an image width
from 1.4m (4.6') to 7m (23') with an aspect ratio of 4 to 3. It leaves the BARCO
factory, adjusted as a ceiling front projector for a screen width of 2.4m. Changing
the image size from the factory preset requires a realignment of the projector.
5975248 BARCOVISION 701 MULTIMEDIA 090797
* What image size? How big should the image be?
INSTALLATION GUIDELINES
* What image size? How big should the image be?
3-3
The BARCOVISION 701 MULTIMEDIA is designed for projecting an image width
from 1.4m (4.6') to 7m (23') with an aspect ratio of 4 to 3. It leaves the BARCO
factory, adjusted as a ceiling front projector for a screen width of 2.4m. Changing
the image size from the factory preset requires a realignment of the projector.
5975248 BARCOVISION 701 MULTIMEDIA 090797
INSTALLATION GUIDELINES
Screen width
3-3
INSTALLATION GUIDELINES
INSTALLATION GUIDELINES
* Where to install the projector?
* Where to install the projector?
To indicate a correct installation position it is necessary to know the distance :
- projector - ceiling
- projector - screen
To indicate a correct installation position it is necessary to know the distance :
- projector - ceiling
- projector - screen
To find this correct position for the BARCOVISION 701 MULTIMEDIA, equipped
with HD145 lenses, formulas are given in the next paragraph.
To find this correct position for the BARCOVISION 701 MULTIMEDIA, equipped
with HD145 lenses, formulas are given in the next paragraph.
Abbreviations used on drawing and diagrams on next pages
Abbreviations used on drawing and diagrams on next pages
B = Distance between ceiling and top of the screen.
B = Distance between ceiling and top of the screen.
A = Correction Value, extra value to be added to B to obtain the correct
installation position. (In some cases the A value can be negative.)
A = Correction Value, extra value to be added to B to obtain the correct
installation position. (In some cases the A value can be negative.)
CD = Total distance between projector and ceiling.
CD = A + B (When the result is negative, enlarge the distance between
ceiling and top of the screen, mount screen lower, until CD becomes zero
or positive)
CD = Total distance between projector and ceiling.
CD = A + B (When the result is negative, enlarge the distance between
ceiling and top of the screen, mount screen lower, until CD becomes zero
or positive)
SW = Screen width.
SW = Screen width.
PD = Perpendicular distance between screen and projector.
PD = Perpendicular distance between screen and projector.
Formulas for Projector to screen distance and correction value A with regard to the
screen width for HD145 lenses (metric).
Formulas (metric)
Formulas (metric)
PD[m] = 1.21 x SW[m] + 0.213
PD[m] = 1.21 x SW[m] + 0.213
A[cm] = 12.95 x SW[m] - 22.83
A[cm] = 12.95 x SW[m] - 22.83
Formulas for Projector to screen distance and correction value A with regard to the
screen width for HD145 lenses (inch).
Formulas (inch)
PD = 1.21 x SW + 8.39
A = 0.1295 x SW - 8.99
5975248 BARCOVISION 701 MULTIMEDIA 090797
INSTALLATION GUIDELINES
INSTALLATION GUIDELINES
3-4
Formulas for Projector to screen distance and correction value A with regard to the
screen width for HD145 lenses (metric).
3-4
Formulas for Projector to screen distance and correction value A with regard to the
screen width for HD145 lenses (inch).
Formulas (inch)
PD = 1.21 x SW + 8.39
A = 0.1295 x SW - 8.99
5975248 BARCOVISION 701 MULTIMEDIA 090797
INSTALLATION GUIDELINES
INSTALLATION GUIDELINES
ceiling
ceiling
PD
B
CD
PD
B
CD
A
A
projector
projector
screen
screen
Front view
Front view
screen width
SW
5975248 BARCOVISION 701 MULTIMEDIA 090797
3-5
Top view
5975248 BARCOVISION 701 MULTIMEDIA 090797
INSTALLATION GUIDELINES
Top view
INSTALLATION GUIDELINES
screen width
SW
3-5
INSTALLATION GUIDELINES
* How to install the projector?
* How to install the projector?
Ceiling mount or table mount?
To install the projector, apply always the BARCO kits which are specially designed for
this function.
Ceiling mount or table mount?
To install the projector, apply always the BARCO kits which are specially designed for
this function.
BARCO ceiling support.
BARCO ceiling support.
Always use the BARCO ceiling support to attach your projector to the ceiling. (BARCO
order number : R9827990)
Always use the BARCO ceiling support to attach your projector to the ceiling. (BARCO
order number : R9827990)
The installation instruction for this support is enclosed in the packet of the set.
The installation instruction for this support is enclosed in the packet of the set.
BARCO projection table.
BARCO projection table.
Height adaptable projection table provides a stable stand for your projector, and makes
it possible to adapt the projector perfectly to the local requirements. (BARCO order
number R9827740).
Height adaptable projection table provides a stable stand for your projector, and makes
it possible to adapt the projector perfectly to the local requirements. (BARCO order
number R9827740).
INSTALLATION GUIDELINES
INSTALLATION GUIDELINES
3-6
INSTALLATION GUIDELINES
5975248 BARCOVISION 701 MULTIMEDIA 090797
3-6
5975248 BARCOVISION 701 MULTIMEDIA 090797
INSTALLATION SET UP
INSTALLATION SET UP
INSTALLATION SET UP
INSTALLATION SET UP
Access to controls
Scan adaptation
Scan adaptation
5975248 BARCOVISION 701 MULTIMEDIA 070597
4-1
INSTALLATION SET UP
INSTALLATION SET UP
Access to controls
5975248 BARCOVISION 701 MULTIMEDIA 070597
4-1
INSTALLATION SET UP
INSTALLATION SET UP
Access to controls
Access to controls
Opening procedure :
Opening procedure :
During the projector set up and installation it is necessary to open the top cover.
During the projector set up and installation it is necessary to open the top cover.
To gain access, handle as follow :
To gain access, procede as follow :
*Turn both lock screws with a screwdriver or a coin counter clockwise.
*Turn both lock screws with a screwdriver or a coin counter clockwise.
* Lift up and pivot the top cover.
* Lift up and pivot the top cover.
* Support the top cover with the hand, no support is incorporated.
* Support the top cover with the hand, no support is incorporated.
INSTALLATION SET UP
INSTALLATION SET UP
4-2
5975248 BARCOVISION 701 MULTIMEDIA 070597
4-2
5975248 BARCOVISION 701 MULTIMEDIA 070597
INSTALLATION SET UP
INSTALLATION SET UP
During some installations it will become handy to remove the top cover totally.
Therefore,
- pivote the top cover ± 60°
During some installations it will become handy to remove the top cover totally.
Therefore,
- pivote the top cover ± 60°
- push the top cover to the front side of the projector until it jumps out of its hings.
Turn the top cover till 90° and lift it up.
- push the top cover to the front side of the projector until it jumps out of its hings.
Turn the top cover till 90° and lift it up.
Re-install the cover :
Hook the top cover into the cabinet hinges. Pivot the top cover 30° and pull it
backwards until it fits in the hinges. Close the cover and secure the lock screws by
turning clockwise with a screwdriver or coin.
Hook the top cover into the cabinet hinges. Pivot the top cover 30° and pull it
backwards until it fits in the hinges. Close the cover and secure the lock screws by
turning clockwise with a screwdriver or coin.
5975248 BARCOVISION 701 MULTIMEDIA 070597
4-3
INSTALLATION SET UP
INSTALLATION SET UP
Re-install the cover :
5975248 BARCOVISION 701 MULTIMEDIA 070597
4-3
INSTALLATION SET UP
INSTALLATION SET UP
Scan adaptation
Scan adaptation
The scanning can be switched by turning the Horizontal and Vertical scan connectors
and the convergence connectors.
To change the scanning, it is necessary to open the projector top cover and to rotate
the chassis.
For opening the projector's top cover, see Getting access to controls.
The scanning can be switch by turning the Horizontal and Vertical scan connectors
and the convergence connectors.
To change the scanning, it is necessary to open the projector top cover and to rotate
the chassis.
For opening the projector's top cover, see Getting access to controls.
WARNING
WARNING
TURN OFF PROJECTOR AND UNPLUG THE POWER CORD BEFORE
CHANGING THE SCAN DIRECTION.
TURN OFF PROJECTOR AND UNPLUG THE POWER CORD BEFORE
CHANGING THE SCAN DIRECTION.
Getting access to the scan connectors and the convergence connectors.
Getting access to the scan connectors and the convergence connectors.
- Open the top cover and to remove it, see Getting access to controls.
- To open the chassis, loosen both indicated retaining screws
- Open the top cover and to remove it, see Getting access to controls.
- To open the chassis, loosen both indicated retaining screws
RS232 IN
RS232 OUT
COMM PORT
(800 peripherals) REMOTE
R
G(S)
B
S
VIDEO
S-VIDEO
RS232 IN
Turn the chassis to the front of the projector until it grips in its locks.
COMM PORT
(800 peripherals) REMOTE
R
G(S)
B
S
VIDEO
S-VIDEO
Turn the chassis to the front of the projector until it grips in its locks.
INSTALLATION SET UP
INSTALLATION SET UP
4-4
RS232 OUT
5975248 BARCOVISION 701 MULTIMEDIA 070597
4-4
5975248 BARCOVISION 701 MULTIMEDIA 070597
INSTALLATION SET UP
INSTALLATION SET UP
Horizontal scan
connectors
Horizontal scan
connectors
Vertical scan
connectors
Vertical scan
connectors
Convergence
connectors
RS232 IN
RS232 OUT
COMM PORT
(800 peripherals) REMOTE
R
G(S)
B
S
VIDEO
Convergence
connectors
S-VIDEO
RS232 OUT
COMM PORT
(800 peripherals) REMOTE
5975248 BARCOVISION 701 MULTIMEDIA 070597
4-5
R
G(S)
B
S
VIDEO
S-VIDEO
INSTALLATION SET UP
INSTALLATION SET UP
RS232 IN
5975248 BARCOVISION 701 MULTIMEDIA 070597
4-5
INSTALLATION SET UP
INSTALLATION SET UP
A : Horizontal scan inversion
A : Horizontal scan inversion
Three connectors are used, one for each horizontal deflection coil. When changing
the horizontal scan, insure that all three connectors are set in the same position. See
position of the connectors for the corresponding projector configuration.
Three connectors are used, one for each horizontal deflection coil. When changing
the horizontal scan, insure that all three connectors are set in the same position. See
position of the connectors for the corresponding projector configuration.
B : Vertical scan inversion
B : Vertical scan inversion
Three connectors are used, one for each vertical deflection coil. When changing the
vertical scan, insure that all three connectors are set in the same position. See
position of the connectors for the corresponding projector configuration.
Three connectors are used, one for each vertical deflection coil. When changing the
vertical scan, insure that all three connectors are set in the same position. See
position of the connectors for the corresponding projector configuration.
Top view of the connectors; upper three connectors for horizontal scan inversion,
lower three for vertical scan inversion.
Top view of the connectors; upper three connectors for horizontal scan inversion,
lower three for vertical scan inversion.
Front / Table
Front / Ceiling
Rear / Table
Front / Table
Rear / Ceiling
Horizont al scan
connectors
Horizont al scan
connectors
Vertical scan
connectors
Vertical scan
connectors
C : Convergence connectors
Rear / Table
Rear / Ceiling
C : Convergence connectors
Three connectors are used. The position of these
connectors has to be changed when switching from one
configuration to another.
With an open chassis, for a front-table or a rear ceiling
configuration, the connectors must be plugged in with the
contacts upwards (away from the tubes). For a frontceiling or rear-table configuration, the connectors must
be plugged in with the contacts facing the tubes
5975248 BARCOVISION 701 MULTIMEDIA 070597
INSTALLATION SET UP
INSTALLATION SET UP
4-6
Contact side
Front / Ceiling
4-6
Contact side
Three connectors are used. The position of these
connectors has to be changed when switching from one
configuration to another.
With an open chassis, for a front-table or a rear ceiling
configuration, the connectors must be plugged in with the
contacts upwards (away from the tubes). For a frontceiling or rear-table configuration, the connectors must
be plugged in with the contacts facing the tubes
5975248 BARCOVISION 701 MULTIMEDIA 070597
INSTALLATION SET UP
INSTALLATION SET UP
After scan inversion, close the chassis and close the top cover. Reconnect the
power cord to the wall outlet.
After scan inversion, close the chassis and close the top cover. Reconnect the
power cord to the wall outlet.
Note
Switching over from floor to ceiling or vice versa requires a complete readjustment of
picture geometry and convergence.
Note
Switching over from floor to ceiling or vice versa requires a complete readjustment of
picture geometry and convergence.
Check of the correct connector position
Note : this check procedure can only be done after power (mains) connection. So, first
continue with the projector set up and the connections and then return to this checking
procedure.
Check of the correct connector position
Note : this check procedure can only be done after power (mains) connection. So, first
continue with the projector set up and the connections and then return to this checking
procedure.
Switch on the BARCOVISION 701 MULTIMEDIA and press ADJUST to start up the
adjustment mode. Select with the control disk 'Service' and press ENTER. The
service menu will be displayed. Select 'PROJECTOR SET UP' and press ENTER.
Select 'IDENTIFICATION' and press ENTER. On this screen, information is given
about the projectors configuration.
Switch on the BARCOVISION 701 MULTIMEDIA and press ADJUST to start up the
adjustment mode. Select with the control disk 'Service' and press ENTER. The
service menu will be displayed. Select 'PROJECTOR SET UP' and press ENTER.
Select 'IDENTIFICATION' and press ENTER. On this screen, information is given
about the projectors configuration.
Configuration when leaving the factory : ceiling/front configuration.
Configuration when leaving the factory : ceiling/front configuration.
Follow next procedure to check the configuration :
Follow next procedure to check the configuration :
- switch on the projector.
- the projector starts up on the last
selected source.
- press the ADJUST key.
- highlight 'service' with the control
disk and press ENTER.
ADJUSTMENT MODE
Select a path from
below:
GUIDED
RANDOM ACCESS
INSTALLATION
SERVICE
IRIS
ADJUSTMENT MODE
Select a path from
below:
GUIDED
RANDOM ACCESS
INSTALLATION
SERVICE
IRIS
source 1
source 1
Select with
or
then <ENTER>
<EXIT> to return
PROJECTOR SET-UP
MEMORY MANAGEMENT
COMMON SETTINGS
I2C DIAGNOSTICS
Select with
or
then <ENTER>
<EXIT> to return.
5975248 BARCOVISION 701 MULTIMEDIA 070597
The 'service mode menu' will be displayed
- select with the control disk 'Projector
set up' and press ENTER.
SERVICE MODE
INSTALLATION SET UP
The 'service mode menu' will be displayed
- select with the control disk 'Projector
set up' and press ENTER.
Select with
or
then <ENTER>
<EXIT> to return
4-7
SERVICE MODE
PROJECTOR SET-UP
MEMORY MANAGEMENT
COMMON SETTINGS
I2C DIAGNOSTICS
Select with
or
then <ENTER>
<EXIT> to return.
5975248 BARCOVISION 701 MULTIMEDIA 070597
INSTALLATION SET UP
- switch on the projector.
- the projector starts up on the last
selected source.
- press the ADJUST key.
- highlight 'service' with the control
disk and press ENTER.
4-7
INSTALLATION SET UP
The 'Projector set up menu' will be
displayed.
- Select with the control disk 'Identification' and press ENTER.
INSTALLATION SET UP
The 'Projector set up menu' will be
displayed.
- Select with the control disk 'Identification' and press ENTER.
PROJECTOR SET-UP
IDENTIFICATION
TOTAL RUN TIME
CHANGE PASSWORD
CHANGE LANGUAGE
CHANGE PROJECTOR ADDRESS
CHANGE BAUDRATE
POWER UP MODE : operating
BARCO LOGO
Select with
or
then <ENTER>
<EXIT> to return.
The projector displays the Identification screen
This screen gives information about
the projector configuration in the subject 'config.'.
V 701 MULTIMEDIA
Proj. address : 001
Soft. Version : 5.00
Config. : Ceiling
front
Baudrate PC : 9600
Text : ON
Serial No. : 10359852
V 701 MULTIMEDIA
Proj. address : 001
Soft. Version : 5.00
Config. : Ceiling
front
Baudrate PC : 9600
Text : ON
Serial No. : 10359852
INSTALLATION SET UP
INSTALLATION SET UP
4-8
IDENTIFICATION
TOTAL RUN TIME
CHANGE PASSWORD
CHANGE LANGUAGE
CHANGE PROJECTOR ADDRESS
CHANGE BAUDRATE
POWER UP MODE : operating
BARCO LOGO
Select with
or
then <ENTER>
<EXIT> to return.
The projector displays the Identification screen
This screen gives information about
the projector configuration in the subject 'config.'.
PROJECTOR SET-UP
5975248 BARCOVISION 701 MULTIMEDIA 070597
4-8
5975248 BARCOVISION 701 MULTIMEDIA 070597
PROJECTOR SET UP
PROJECTOR SET UP
PROJECTOR SET UP
PROJECTOR SET UP
PROJECTOR SET UP
PROJECTOR SET UP
Password mode
Password mode
5975248 BARCOVISION 701 MULTIMEDIA 070597
5-1
5975248 BARCOVISION 701 MULTIMEDIA 070597
5-1
PROJECTOR SET UP
PROJECTOR SET UP
Projector Set Up
Projector Set Up
The strap on the CPU unit allow a set up of the password mode.
The strap on the CPU unit allow a set up of the password mode.
Gaining access to the strap
Gaining access to the strap
- Open the top cover (see installation set up)
- Open the chassis (see installation set up)
- Open the top cover (see installation set up)
- Open the chassis (see installation set up)
strap
strap
Horizontal scan
connectors
Horizontal scan
connectors
Vertical scan
connectors
Vertical scan
connectors
Convergence
connectors
RS232 OUT
COMM PORT
(800 peripherals) REMOTE
R
G(S)
B
S
VIDEO
S-VIDEO
5975248 BARCOVISION 701 MULTIMEDIA 070597
PROJECTOR SET UP
PROJECTOR SET UP
5-2
RS232 IN
Convergence
connectors
5-2
RS232 IN
RS232 OUT
COMM PORT
(800 peripherals) REMOTE
R
G(S)
B
S
VIDEO
S-VIDEO
5975248 BARCOVISION 701 MULTIMEDIA 070597
PROJECTOR SET UP
PROJECTOR SET UP
Password mode
Password mode
With a strap on the controller unit, the important projector adjustments can be
protected with a password. When the password feature is enabled (strap mounted
on both legs), the customer has to enter a password before he can enter the specific
adjustment.
With a strap on the controller unit, the important projector adjustments can be
protected with a password. When the password feature is enabled (strap mounted
on both legs), the customer has to enter a password before he can enter the specific
adjustment.
When the password menus are disabled (strap mounted only on one leg), all
adjustments are free. This position of the strap is useful for qualified service
technicians because they do not need a password during service.
Position of the strap :
When the password menus are disabled (strap mounted only on one leg), all
adjustments are free. This position of the strap is useful for qualified service
technicians because they do not need a password during service.
Position of the strap :
ON : password disabled
OFF : password enabled
ON : password disabled
OFF : password enabled
Socket for strap
PROJECTOR SET UP
PROJECTOR SET UP
Socket for strap
5975248 BARCOVISION 701 MULTIMEDIA 070597
5-3
5975248 BARCOVISION 701 MULTIMEDIA 070597
5-3
PROJECTOR SET UP
PROJECTOR SET UP
PROJECTOR SET UP
5-4
PROJECTOR SET UP
5975248 BARCOVISION 701 MULTIMEDIA 070597
5-4
5975248 BARCOVISION 701 MULTIMEDIA 070597
POWER CONNECTION
POWER CONNECTION
POWER (MAINS) CONNECTION
POWER CONNECTION
POWER CONNECTION
POWER (MAINS) CONNECTION
5975248 BARCOVISION 701 MULTIMEDIA 090497
6-1
5975248 BARCOVISION 701 MULTIMEDIA 090497
6-1
POWER CONNECTION
POWER CONNECTION
Power (mains) cord connection
Power (mains) cord connection
Use the supplied power cord to connect your projector to the wall outlet. Plug the female
power connector into the male connector at the front of the projector.
Use the supplied power cord to connect your projector to the wall outlet. Plug the female
power connector into the male connector at the front of the projector.
See installation instructions before
connecting to the supply
OFF
ON
See installation instructions before
connecting to the supply
V NOM 120/230 Volt
I MAX 5/2.5 AMP
FREQ 60/50 Hz
OFF
See installation instructions before
connecting to the supply
See installation instructions before
connecting to the supply
V NOM 120/230 Volt
I MAX 5/2.5 AMP
FREQ 60/50 Hz
V NOM 120/230 Volt
I MAX 5/2.5 AMP
FREQ 60/50 Hz
OFF ON
OFF ON
Input power (mains) voltage adaptation.
V NOM 120/230 Volt
I MAX 5/2.5 AMP
FREQ 60/50 Hz
Input power (mains) voltage adaptation.
Attention
Attention
The BARCOVISION 701 MULTIMEDIA - R9000740 leaves the factory to operate on
a mains (power) input of 230 Vac.
The BARCOVISION 701 MULTIMEDIA - R9000740 leaves the factory to operate on
a mains (power) input of 230 Vac.
Adaptation of the power input of the projector from 230 VAC to 120 VAC or vice
versa is possible. Follow the procedure as described below.
Adaptation of the power input of the projector from 230 VAC to 120 VAC or vice
versa is possible. Follow the procedure as described below.
Procedure
- Unplug the power cord from the power input on the front panel.
- Remove the front panel by loosening both retaining screws and take off the plastic
cover plate.
5975248 BARCOVISION 701 MULTIMEDIA 090497
POWER CONNECTION
POWER CONNECTION
6-2
ON
6-2
Procedure
- Unplug the power cord from the power input on the front panel.
- Remove the front panel by loosening both retaining screws and take off the plastic
cover plate.
5975248 BARCOVISION 701 MULTIMEDIA 090497
POWER CONNECTION
POWER CONNECTION
See installation instructions before
connecting to the supply
OFF ON
- Push out the module.
POWER CONNECTION
- Push out the module.
5975248 BARCOVISION 701 MULTIMEDIA 090497
V NOM 120/230 Volt
I MAX
5/2.5 AMP
FREQ 60/50 Hz
POWER CONNECTION
OFF ON
See installation instructions before
connecting to the supply
V NOM 120/230 Volt
I MAX
5/2.5 AMP
FREQ 60/50 Hz
6-3
5975248 BARCOVISION 701 MULTIMEDIA 090497
6-3
POWER CONNECTION
POWER CONNECTION
- Loosen both screws of the protective cover and take off the cover.
- Loosen both screws of the protective cover and take off the cover.
Retaining screws
Retaining screws
120 V
230 V
- Pull out the 'power selector plug' and re-insert it as illustrated, depending on the wall
outlet in the room.
- Re-mount the protective cover and secure with both screws.
- Re-insert the module.
- Put the plastic cover back and secure both retaining screws.
- Pull out the 'power selector plug' and re-insert it as illustrated, depending on the wall
outlet in the room.
- Re-mount the protective cover and secure with both screws.
- Re-insert the module.
- Put the plastic cover back and secure both retaining screws.
Fuses
Fuses
Warning
For continued protection against fire hazard :
- replace with the same type of fuse
- refer replacement to qualified service personnel
Fuse type : 2 x T5A/250V (Barco order number : R314104)
5975248 BARCOVISION 701 MULTIMEDIA 090497
POWER CONNECTION
POWER CONNECTION
6-4
120 V
230 V
6-4
Warning
For continued protection against fire hazard :
- replace with the same type of fuse
- refer replacement to qualified service personnel
Fuse type : 2 x T5A/250V (Barco order number : R314104)
5975248 BARCOVISION 701 MULTIMEDIA 090497
POWER CONNECTION
POWER CONNECTION
Switching on/off
Switching on/off
The projector is switched ON and OFF using the power (mains) switch ON/OFF.
The projector is switched ON and OFF using the power (mains) switch ON/OFF.
Pressed : ON
Not pressed : OFF
Pressed : ON
Not pressed : OFF
The projector can start now in the 'operational mode' (image displayed) or in the 'stand
by mode', depending on the position of the 'power up' dip switch on the controller unit.
This DIP switch is set during installation by a qualified technician. If you want to
change this start up mode, call a qualified technician.
The projector can start now in the 'operational mode' (image displayed) or in the 'stand
by mode', depending on the position of the 'power up' dip switch on the controller unit.
This DIP switch is set during installation by a qualified technician. If you want to
change this start up mode, call a qualified technician.
Stand by indication lamp :
Stand by indication lamp :
no light up : projector in operational mode
red : projector is in stand by.
no light up : projector in operational mode
red : projector is in stand by.
Leds on the front plate of the projector
Leds on the front plate of the projector
POWER CONNECTION
POWER CONNECTION
COINC
AAAA
AAAA
AAAA
AAAA
HOLD DOWN HD
SF
HOLD DOWN EHT
6-5
STANDBY
5975248 BARCOVISION 701 MULTIMEDIA 090497
-17V
+HTHD
+CONV
+210V
-9V
+30V
+9V
+17V
-CONV
HOLD DOWN HD
COINC
SF
HOLD DOWN EHT
STANDBY
-17V
+HTHD
+CONV
+210V
-9V
+30V
+9V
+17V
-CONV
AAAA
AAAA
AAAA
AAAA
5975248 BARCOVISION 701 MULTIMEDIA 090497
6-5
POWER CONNECTION
POWER CONNECTION
POWER CONNECTION
6-6
POWER CONNECTION
5975248 BARCOVISION 701 MULTIMEDIA 090497
6-6
5975248 BARCOVISION 701 MULTIMEDIA 090497
INSTALLATION ADJUSTMENTS
INSTALLATION ADJUSTMENTS
INSTALLATION ADJUSTMENTS
INSTALLATION ADJUSTMENTS
Overview flow chart installation mode
Overview flow chart installation mode
Scheimpfug adjustment
Scheimpfug adjustment
Optical lens focusing
Optical lens focusing
Raster centering
5975248 BARCOVISION 701 MULTIMEDIA 070597
7-1
CRT projection angle adjustment
Alignment of the projector
5975248 BARCOVISION 701 MULTIMEDIA 070597
INSTALLATION ADJUSTMENTS
Alignment of the projector
INSTALLATION ADJUSTMENTS
CRT projection angle adjustment
Raster centering
7-1
INSTALLATION ADJUSTMENTS
INSTALLATION ADJUSTMENTS
Entering the adjustment mode
Entering the adjustment mode
ADJUSTMENT MODE
ADJUSTMENT MODE
Select a path from
below:
Select a path from
below:
GUIDED
RANDOM ACCESS
INSTALLATION
SERVICE
IRIS
GUIDED
RANDOM ACCESS
INSTALLATION
SERVICE
IRIS
source 1
source 1
Select with
or
then <ENTER>
<EXIT> to return
Select with
or
then <ENTER>
<EXIT> to return
Installation
Service
Guided
Adjustment
5975248 BARCOVISION 701 MULTIMEDIA 070597
INSTALLATION ADJUSTMENTS
INSTALLATION ADJUSTMENTS
7-2
Random Access
Adjustment
IRIS
Installation
IRIS
(only for qualified
technician)
7-2
(only for qualified
technician)
Random Access
Adjustment
Service
Guided
Adjustment
5975248 BARCOVISION 701 MULTIMEDIA 070597
INSTALLATION ADJUSTMENTS
INSTALLATION ADJUSTMENTS
Overview flow chart installation mode.
Overview flow chart installation mode.
LOOSEN THE 4
LENS MOUNTING NUTS ON
EACH LENS, UNTIL THE TAG
OF EACH SCHEIMPFLUG RING
CAN BE MOVED TO ITS
DESIRED POSITION
(1.4 M, 2.4 M OR 4.0 M
SCREEN WIDTH°
<ENTER> to continue
<EXIT> to return
OPTICAL LENS FOCUSING
SCHEIMPFLUG ADJUSTMENT
1. LOOSEN THE NUT ON THE
REAR OF THE XXXX LENS,
ROTATE THE LENS BARREL
TO FOCUS THE CENTER
OF THE IMAGE,
THEN TIGHTEN THE NUT
2. LOOSEN THE NUT ON THE
FRONT OF THE XXXX LENS
AND ROTATE THE FRONT
SECTION OF THE LENS TO
FOCUS THE CORNERS OF THE
IMAGE, THEN TIGHTEN THE NUT.
LOOSEN THE 4
LENS MOUNTING NUTS ON
EACH LENS, UNTIL THE TAG
OF EACH SCHEIMPFLUG RING
CAN BE MOVED TO ITS
DESIRED POSITION
(1.4 M, 2.4 M OR 4.0 M
SCREEN WIDTH°
<ENTER> to continue
<EXIT> to return
<ENTER> to continue
<EXIT> to return
This menu is repeated 3
times, first in Green,
then in Red and then in
Blue
CRT PROJECTION ANGLE
ADJUSTMENT
CRT PROJECTION ANGLE IS
THE FIRST STEP OF STATIC
CONVERGENCE ADJUSTMENT.
IT IS CRITICAL THAT THE
RASTERS ARE CENTERED ON
THE CRT FACE PLATES
PRIOR TO PERFORMING
THIS STEP.
...
<ENTER> to read more
<EXIT> to return
RASTER CENTERING
CRT PROJECTION ANGLE
ADJUSTMENT
CONTRAST LEVEL IS REDUCED
AND BRIGHTNESS INCREASED
TO MAKE THE RASTER
VISIBLE ON THE FACE PLATE
OF EACH CRT.
CRT PROJECTION ANGLE IS
THE FIRST STEP OF STATIC
CONVERGENCE ADJUSTMENT.
IT IS CRITICAL THAT THE
RASTERS ARE CENTERED ON
THE CRT FACE PLATES
PRIOR TO PERFORMING
THIS STEP.
...
<ENTER> to read more
USE THE ARROW KEYS
TO CENTER THE RASTER
ON THE GREEN, RED AND
BLUE CRT RESPECTIVELY
<ENTER> to continue
<EXIT> to return
<EXIT> to return
LOOSEN BOLTS A AND B
TO PIVOT THE RED CRT,
AND BOLDS C AND D
TO PIVOT THE BLUE CRT.
<ENTER> to continue
<EXIT> to return
5975248 BARCOVISION 701 MULTIMEDIA 070597
CRT
PROJECTION ANGLE
ADJUSTMENT
Align crosshairs
<ENTER> continue
<EXIT> to return
<ENTER> to continue
<EXIT> to return
RASTER CENTERING
CONTRAST LEVEL IS REDUCED
AND BRIGHTNESS INCREASED
TO MAKE THE RASTER
VISIBLE ON THE FACE PLATE
OF EACH CRT.
USE THE ARROW KEYS
TO CENTER THE RASTER
ON THE GREEN, RED AND
BLUE CRT RESPECTIVELY
<ENTER> to continue
<EXIT> to return
This menu is displayed in green. After ENTER is
pressed, only the green raster is displayed and the
control disk may be used to center the raster on the
CRT surface. This menu is also displayed, once in
red and once in blue.
INSTALLATION ADJUSTMENTS
DURING THIS PROCEDURE,
RED ON GREEN AND THEN
BLUE ON GREEN CROSSHAIRS
WILL BE DISPLAYED
TO ALLOW THE RED AND
BLUE CRTS TO BE ALIGNED
WITH THE GREEN CRT.
1. LOOSEN THE NUT ON THE
REAR OF THE XXXX LENS,
ROTATE THE LENS BARREL
TO FOCUS THE CENTER
OF THE IMAGE,
THEN TIGHTEN THE NUT
2. LOOSEN THE NUT ON THE
FRONT OF THE XXXX LENS
AND ROTATE THE FRONT
SECTION OF THE LENS TO
FOCUS THE CORNERS OF THE
IMAGE, THEN TIGHTEN THE NUT.
This menu is repeated 3
times, first in Green,
then in Red and then in
Blue
This menu is displayed in green. After ENTER is
pressed, only the green raster is displayed and the
control disk may be used to center the raster on the
CRT surface. This menu is also displayed, once in
red and once in blue.
CRT PROJECTION ANGLE
ADJUSTMENT
OPTICAL LENS FOCUSING
7-3
CRT PROJECTION ANGLE
ADJUSTMENT
DURING THIS PROCEDURE,
RED ON GREEN AND THEN
BLUE ON GREEN CROSSHAIRS
WILL BE DISPLAYED
TO ALLOW THE RED AND
BLUE CRTS TO BE ALIGNED
WITH THE GREEN CRT.
LOOSEN BOLTS A AND B
TO PIVOT THE RED CRT,
AND BOLDS C AND D
TO PIVOT THE BLUE CRT.
<ENTER> to continue
<EXIT> to return
5975248 BARCOVISION 701 MULTIMEDIA 070597
CRT
PROJECTION ANGLE
ADJUSTMENT
Align crosshairs
<ENTER> continue
<EXIT> to return
INSTALLATION ADJUSTMENTS
SCHEIMPFLUG ADJUSTMENT
7-3
INSTALLATION ADJUSTMENTS
INSTALLATION ADJUSTMENTS
Installation mode start up
Installation mode start up
It will be necessary to perform several mechanical adjustments while in the
installation mode. Remove the top cover in order to gain access to the adjustment
points (see Access to controls).
Two possible ways to enter the installation mode :
It will be necessary to perform several mechanical adjustments while in the
installation mode. Remove the top cover in order to gain access to the adjustment
points (see Access to controls).
Two possible ways to enter the installation mode :
a) Using the RCU.
a) Using the RCU.
Press the ADJUST key.
The projector displays the path selection menu.
Press the ADJUST key.
The projector displays the path selection menu.
b) Using the local keypad.
b) Using the local keypad.
Press the ADJUST key.
The projector displays the General
access menu.
ADJUST
STANDBY
Use the control disk to highlight enter ADJUST and press
ENTER. The path selection
menu will be displayed.
Press the ADJUST key.
The projector displays the General
access menu.
EXIT
4
2
Use the control disk to highlight enter ADJUST and press
ENTER. The path selection
menu will be displayed.
SHARPNESS
TINT
COLOR
BRIGHTNESS
CONTRAST
<EXIT> to return
5975248 BARCOVISION 701 MULTIMEDIA 070597
4
2
SHARPNESS
TINT
COLOR
BRIGHTNESS
CONTRAST
Enter ADJUST
INSTALLATION ADJUSTMENTS
INSTALLATION ADJUSTMENTS
7-4
,
or
then <ENTER>.
ENTER
GENERAL ACCESS
3
1
Enter ADJUST
Select with
EXIT
STANDBY
ENTER
GENERAL ACCESS
3
1
ADJUST
7-4
Select with
,
or
then <ENTER>.
<EXIT> to return
5975248 BARCOVISION 701 MULTIMEDIA 070597
INSTALLATION ADJUSTMENTS
Push the control disk up or down to
highlight "Installation" and press ENTER.
INSTALLATION ADJUSTMENTS
Push the control disk up or down to
highlight "Installation" and press ENTER.
ADJUSTMENT MODE
ADJUSTMENT MODE
Select a path from
below:
Select a path from
below:
GUIDED
RANDOM ACCESS
INSTALLATION
SERVICE
IRIS
GUIDED
RANDOM ACCESS
INSTALLATION
SERVICE
IRIS
source 1
source 1
Select with
or
then <ENTER>
<EXIT> to return
Select with
or
then <ENTER>
<EXIT> to return
ENTER continues displaying a WARNING.
EXIT returns to operational mode.
ADJUST returns to operational mode.
A warning will be displayed on the
screen.
If you are qualified installation or service personnel, press ENTER to start up
the installation mode.
When entering the installation mode,
the projector will automatically switch
to the internal pattern on 15 kHz/50 Hz.
ENTER continues displaying a WARNING.
EXIT returns to operational mode.
ADJUST returns to operational mode.
A warning will be displayed on the
screen.
If you are qualified installation or service personnel, press ENTER to start up
the installation mode.
WARNING
RISK OF ELECTRICAL SHOCK
NO USER ADJUSTABLE PARTS
INSIDE
THE FOLLOWING
INSTALLATION MENUS
ARE RESERVED TO,
AND TO BE PERFORMED ONLY
BY BARCO PERSONNEL, OR
BARCO AUTHORIZED DEALERS
When entering the installation mode,
the projector will automatically switch
to the internal pattern on 15 kHz/50 Hz.
IF QUALIFIED, PRESS
<ENTER> TO CONTINUE, OR
IF NOT, <EXIT> TO RETURN.
IF QUALIFIED, PRESS
<ENTER> TO CONTINUE, OR
IF NOT, <EXIT> TO RETURN.
ENTER asks for your password.
EXIT returns to the path selection menu.
INSTALLATION ADJUSTMENTS
5975248 BARCOVISION 701 MULTIMEDIA 070597
THE FOLLOWING
INSTALLATION MENUS
ARE RESERVED TO,
AND TO BE PERFORMED ONLY
BY BARCO PERSONNEL, OR
BARCO AUTHORIZED DEALERS
INSTALLATION ADJUSTMENTS
ENTER asks for your password.
EXIT returns to the path selection menu.
WARNING
RISK OF ELECTRICAL SHOCK
NO USER ADJUSTABLE PARTS
INSIDE
7-5
5975248 BARCOVISION 701 MULTIMEDIA 070597
7-5
INSTALLATION ADJUSTMENTS
INSTALLATION ADJUSTMENTS
When the password mode is active, your password will be asked.
When the password mode is active, your password will be asked.
Your password contains 4 digits.
Your password contains 4 digits.
a) Adjusting the projector with the RCU.
a) Adjusting the projector with the RCU.
Enter the digits with the numeric keys
on the RCU.
Enter the digits with the numeric keys
on the RCU.
Example : 2 3 1 9
Example : 2 3 1 9
For each digit entered, a 'X' appears on
the screen under the displayed text
'enter password'.
For each digit entered, a 'X' appears on
the screen under the displayed text
'enter password'.
When your password is correct, you get
access to the 'Adjustment mode'.
When the entered password is wrong,
The message 'Wrong password !!!' will
be displayed. The projector stays on
the previous selected item.
When your password is correct, you get
access to the 'Adjustment mode'.
When the entered password is wrong,
The message 'Wrong password !!!' will
be displayed. The projector stays on
the previous selected item.
enter
password
xxxx
197
Factory programmed
password :
197
Factory programmed
password :
0000
0000
WRONG
PASSWORD
!!!
WRONG
PASSWORD
!!!
INSTALLATION ADJUSTMENTS
INSTALLATION ADJUSTMENTS
7-6
enter
password
xxxx
5975248 BARCOVISION 701 MULTIMEDIA 070597
7-6
5975248 BARCOVISION 701 MULTIMEDIA 070597
INSTALLATION ADJUSTMENTS
INSTALLATION ADJUSTMENTS
b) adjusting the projector with the local keypad.
When the 'compose password' menu
is displayed, select with the control
disk the first digit of your password
and press ENTER. Continue by selecting the second digit with the control disk and press ENTER. Handle in
the same way for the third and fourth
digit.
b) adjusting the projector with the local keypad.
When the 'compose password' menu
is displayed, select with the control
disk the first digit of your password
and press ENTER. Continue by selecting the second digit with the control disk and press ENTER. Handle in
the same way for the third and fourth
digit.
COMPOSE
PASSWORD
???
7 8 9
4 5 6
1 2 3
0
Select with
,
or
then <ENTER>
<EXIT> to return
Select with
When your password is correct, you
get access to the 'Adjustment mode'.
,
or
then <ENTER>
<EXIT> to return
When the entered password is wrong,
the message 'Wrong password' will be
displayed.
INSTALLATION ADJUSTMENTS
When the entered password is wrong,
the message 'Wrong password' will be
displayed.
5975248 BARCOVISION 701 MULTIMEDIA 070597
???
7 8 9
4 5 6
1 2 3
0
INSTALLATION ADJUSTMENTS
When your password is correct, you get
access to the 'Adjustment mode'.
COMPOSE
PASSWORD
7-7
5975248 BARCOVISION 701 MULTIMEDIA 070597
7-7
INSTALLATION ADJUSTMENTS
INSTALLATION ADJUSTMENTS
Scheimpfug adjustment
Scheimpfug adjustment
The scheimpfug correction can be adjusted separately for the three tubes within 3
ranges:
The scheimpfug correction can be adjusted separately for the three tubes within 3
ranges:
range 1 : 1.4 m (55") to 1.9 m (75"), optimum screen width 1.4 m (55")
range 2 : 1.9 m (75") to 3.2 m (126"), optimum screen width 2.4 m (94")
range 3 : 3.2 m (126") to 6 m (236"), optimum screen width 4 m (157")
range 1 : 1.4 m (55") to 1.9 m (75"), optimum screen width 1.4 m (55")
range 2 : 1.9 m (75") to 3.2 m (126"), optimum screen width 2.4 m (94")
range 3 : 3.2 m (126") to 6 m (236"), optimum screen width 4 m (157")
A correct scheimpfug setting gives the possibility to focus the lenses for a sharp image
in all screen areas.
A correct scheimpfug setting gives the possibility to focus the lenses for a sharp image
in all screen areas.
To change the setting from one range to another, some mechanical actions have to
done.
To change the setting from one range to another, some mechanical actions have
to done.
range 1
min. SW : 1.40 m (55")
max. SW : 1.90 m (75")
range 1
min. SW : 1.40 m (55")
max. SW : 1.90 m (75")
1.40m
1.90m
1.90m
range 2
min. SW : 1.90 m (75")
max. SW : 3.20 m (126")
range 2
min. SW : 1.90 m (75")
max. SW : 3.20 m (126")
1.90m
5975248 BARCOVISION 701 MULTIMEDIA 070597
INSTALLATION ADJUSTMENTS
INSTALLATION ADJUSTMENTS
7-8
range 3
min. SW : 3.20 m (126")
max. SW : 6.00 m (236")
3.20m
6.00m
1.90m
3.20m
3.20m
range 3
min. SW : 3.20 m (126")
max. SW : 6.00 m (236")
1.40m
7-8
3.20m
6.00m
5975248 BARCOVISION 701 MULTIMEDIA 070597
INSTALLATION ADJUSTMENTS
INSTALLATION ADJUSTMENTS
1. Open the top cover (see Gaining access to controls)
1. Open the top cover (see Gaining access to controls)
2. Loosen the lens bolts (do not remove them), and slide the lens to the front until the
scheimflug ring can move freely (nutdriver 8 mm or screwdriver).
2. Loosen the lens bolts (do not remove them), and slide the lens to the front until the
scheimflug ring can move freely (nutdriver 8 mm or screwdriver).
Lens bolts
Green lens
Lens bolts
Red lens
Lens bolts
Blue lens
Lens bolts
Green lens
See installation instructions before
connecting to the supply
OFF
ON
See installation instructions before
connecting to the supply
V NOM 120/230 Volt
I MAX 5/2.5 AMP
FREQ 60/50 Hz
OFF
3. Push the scheimpfug ring to its correct position (front view).
range 1 : to the right
range 2 : in the middle
range 3 : to the left
range 1 : to the right
range 2 : in the middle
range 3 : to the left
range 2
range 1
range 3
See installation instructions before
connecting to the supply
OFF ON
V NOM 120/230 Volt
I MAX 5/2.5 AMP
FREQ 60/50 Hz
4. Push the lens back till it fits in the ring and secure the four bolts.
5975248 BARCOVISION 701 MULTIMEDIA 070597
V NOM 120/230 Volt
I MAX 5/2.5 AMP
FREQ 60/50 Hz
Scheimpfug correction handle
Blue
range 2
range 1
range 3
range 2
range 1
range 3
INSTALLATION ADJUSTMENTS
range 2
range 1
range 3
Red
Green
ON
3. Push the scheimpfug ring to its correct position (front view).
Scheimpfug correction handle
Blue
Lens bolts
Red lens
7-9
Red
Green
range 2
range 1
range 3
range 2
range 1
range 3
See installation instructions before
connecting to the supply
OFF
ON
4. Push the lens back till it fits in the ring and secure the four bolts.
5975248 BARCOVISION 701 MULTIMEDIA 070597
V NOM 120/230 Volt
I MAX 5/2.5 AMP
FREQ 60/50 Hz
INSTALLATION ADJUSTMENTS
Lens bolts
Blue lens
7-9
INSTALLATION ADJUSTMENTS
INSTALLATION ADJUSTMENTS
Optical lens focusing
Optical lens focusing
The optical focusing procedure is
performed separately for each lens.
The appropriate CRT will be switched
on as the user proceeds through the
optical focusing adjustment sequence.
Each lens has two focus adjustment points, one at the rear of the
lens and one at the front. The
center of the projected image is
focused by loosening the wing nut
at the rear end of the lens and
rotating the lens barrel until the
center of the image is clearly focused. The corners of the projected image are focused by loosening the wing nut at the front end
of the lens and rotating the lens
barrel until the corners of the image
are clearly focused. Repetition of
these adjustments may be necessary to optimize optical focusing.
Press ENTER key to continue.
The optical focusing procedure is
performed separately for each lens.
The appropriate CRT will be switched
on as the user proceeds through the
optical focusing adjustment sequence.
OPTICAL LENS FOCUSING
1. LOOSEN THE NUT ON THE
REAR OF THE XXXX LENS,
ROTATE THE LENS BARREL
TO FOCUS THE CENTER
OF THE IMAGE,
THEN TIGHTEN THE NUT
2. LOOSEN THE NUT ON THE
FRONT OF THE XXXX LENS
AND ROTATE THE FRONT
SECTION OF THE LENS TO
FOCUS THE CORNERS OF THE
IMAGE, THEN TIGHTEN THE NUT.
Each lens has two focus adjustment points, one at the rear of the
lens and one at the front. The
center of the projected image is
focused by loosening the wing nut
at the rear end of the lens and
rotating the lens barrel until the
center of the image is clearly focused. The corners of the projected image are focused by loosening the wing nut at the front end
of the lens and rotating the lens
barrel until the corners of the image
are clearly focused. Repetition of
these adjustments may be necessary to optimize optical focusing.
Press ENTER key to continue.
<ENTER> to continue
<EXIT> to return
ENTER continues to Raster centering.
EXIT returns to scheimpfug adjustment
ADJUST returns to operational mode.
1. LOOSEN THE NUT ON THE
REAR OF THE XXXX LENS,
ROTATE THE LENS BARREL
TO FOCUS THE CENTER
OF THE IMAGE,
THEN TIGHTEN THE NUT
2. LOOSEN THE NUT ON THE
FRONT OF THE XXXX LENS
AND ROTATE THE FRONT
SECTION OF THE LENS TO
FOCUS THE CORNERS OF THE
IMAGE, THEN TIGHTEN THE NUT.
<ENTER> to continue
<EXIT> to return
ENTER continues to Raster centering.
EXIT returns to scheimpfug adjustment
ADJUST returns to operational mode.
Center
focusing
Center
focusing
Corner
focusing
XXXX = respectively red, green and blue.
5975248 BARCOVISION 701 MULTIMEDIA 070597
INSTALLATION ADJUSTMENTS
INSTALLATION ADJUSTMENTS
7-10
OPTICAL LENS FOCUSING
7-10
Corner
focusing
XXXX = respectively red, green and blue.
5975248 BARCOVISION 701 MULTIMEDIA 070597
INSTALLATION ADJUSTMENTS
INSTALLATION ADJUSTMENTS
Electrical focusing
Electrical focusing
The electrical focus for red, green and blue is factory preset. When they have to
be readjusted, follow the procedure as described below :
- Ensure the lenses are correctly focused.
- Open the top cover.
- Adjust separately the focus control for red, green and blue for the sharpest image
on the screen.
The electrical focus for red, green and blue is factory preset. When they have to be
readjusted, follow the procedure as described below :
- Ensure the lenses are correctly focused.
- Open the top cover.
- Adjust separately the focus control for red, green and blue for the sharpest image
on the screen.
Electrical focus
Red Green Blue
Red Green Blue
INSTALLATION ADJUSTMENTS
INSTALLATION ADJUSTMENTS
Electrical focus
5975248 BARCOVISION 701 MULTIMEDIA 070597
7-11
5975248 BARCOVISION 701 MULTIMEDIA 070597
7-11
INSTALLATION ADJUSTMENTS
INSTALLATION ADJUSTMENTS
Raster centering
Raster centering
The raster must be centered on the CRT screen surface of each tube, therefore, it is
necessary to look into the lenses.
The raster must be centered on the CRT screen surface of each tube, therefore,
it is necessary to look into the lenses.
Caution : To avoid eye discomfort while performing these adjustments, reduce the
contrast and gradually increase the brightness level until the raster becomes visible
behind the image.
Caution : To avoid eye discomfort while performing these adjustments, reduce the
contrast and gradually increase the brightness level until the raster becomes
visible behind the image.
Warning : In order to ensure maximum CRT longevity and
to avoid CRT damage, do not shift the raster outside the
phosphor area of the CRT.
Warning : In order to ensure maximum CRT longevity and to
avoid CRT damage, do not shift the raster outside the phosphor area of the CRT.
Press ENTER to display the raster on
the green CRT.
Press ENTER to display the raster on
the green CRT.
RASTER CENTERING
Look into the green lens and shift the
raster with the control disk until it is
centered in the middle of the CRT
faceplate.
RASTER CENTERING
Look into the green lens and shift the
raster with the control disk until it is
centered in the middle of the CRT
faceplate.
CONTRAST LEVEL IS REDUCED
AND BRIGHTNESS INCREASED
TO MAKE THE RASTER
VISIBLE ON THE FACE PLATE
OF EACH CRT.
USE THE ARROW KEYS
TO CENTER THE RASTER
ON THE GREEN, RED AND
BLUE CRT RESPECTIVELY
CONTRAST LEVEL IS REDUCED
AND BRIGHTNESS INCREASED
TO MAKE THE RASTER
VISIBLE ON THE FACE PLATE
OF EACH CRT.
USE THE ARROW KEYS
TO CENTER THE RASTER
ON THE GREEN, RED AND
BLUE CRT RESPECTIVELY
<ENTER> to continue
<EXIT> to return
forbidden area
forbidden area
projected raster
crt faceplate border
phosphor border
5975248 BARCOVISION 701 MULTIMEDIA 070597
INSTALLATION ADJUSTMENTS
INSTALLATION ADJUSTMENTS
7-12
<ENTER> to continue
<EXIT> to return
7-12
projected raster
crt faceplate border
phosphor border
5975248 BARCOVISION 701 MULTIMEDIA 070597
INSTALLATION ADJUSTMENTS
INSTALLATION ADJUSTMENTS
correct raster position
correct raster position
Press ENTER to activate the raster on
the Blue CRT faceplate.
Shift the blue raster with the control
disk until the raster is centered on the
CRT faceplate.
Press ENTER to continue with the
CRT projection angle adjustment
5975248 BARCOVISION 701 MULTIMEDIA 070597
ENTER continues to CRT Projection
angle Adjustment.
EXIT returns to Optical focusing.
ADJUST returns to operational mode.
7-13
Press ENTER to activate the raster on
the Red CRT faceplate.
Shift the raster with the control disk
until the raster is centered in the middle of the CRT faceplate.
Press ENTER to activate the raster on
the Blue CRT faceplate.
Shift the blue raster with the control
disk until the raster is centered on the
CRT faceplate.
Press ENTER to continue with the CRT
projection angle adjustment
5975248 BARCOVISION 701 MULTIMEDIA 070597
ENTER continues to CRT Projection
angle Adjustment.
EXIT returns to Optical focusing.
ADJUST returns to operational mode.
INSTALLATION ADJUSTMENTS
Press ENTER to activate the raster on
the Red CRT faceplate.
Shift the raster with the control disk
until the raster is centered in the middle of the CRT faceplate.
wrong raster position
INSTALLATION ADJUSTMENTS
wrong raster position
7-13
INSTALLATION ADJUSTMENTS
INSTALLATION ADJUSTMENTS
CRT projection angle adjustment
CRT projection angle adjustment
The projection angle of the red and blue CRT's is dependent on the desired size
of the projected image. If the centers of green, blue and red do not coincide, the
CRT projection angle must be adjusted. Never try to correct this misalignment with
the shift correction or the static convergence controls. These controls may only be
applied to correct small errors which cannot be corrected by the CRT angle
adjustment.
The projection angle of the red and blue CRT's is dependent on the desired size
of the projected image. If the centers of green, blue and red do not coincide, the
CRT projection angle must be adjusted. Never try to correct this misalignment with
the shift correction or the static convergence controls. These controls may only be
applied to correct small errors which cannot be corrected by the CRT angle
adjustment.
Ensure that the rasters are centered
on the CRT face.
Ensure that the rasters are centered
on the CRT face.
Press ENTER to start the CRT angle
adjustment procedure. A crosshairs
(green and red) will be displayed on
the screen.
CRT PROJECTION ANGLE
ADJUSTMENT
CRT PROJECTION ANGLE IS
THE FIRST STEP OF STATIC
CONVERGENCE ADJUSTMENT.
Press ENTER to start the CRT angle
adjustment procedure. A crosshairs
(green and red) will be displayed on
the screen.
IT IS CRITICAL THAT THE
RASTERS ARE CENTERED ON
THE CRT FACE PLATES
PRIOR TO PERFORMING
THIS STEP.
...
<ENTER> to read more
<EXIT> to return
CRT PROJECTION ANGLE IS
THE FIRST STEP OF STATIC
CONVERGENCE ADJUSTMENT.
IT IS CRITICAL THAT THE
RASTERS ARE CENTERED ON
THE CRT FACE PLATES
PRIOR TO PERFORMING
THIS STEP.
...
<ENTER> to read more
<EXIT> to return
ENTER continues with the second part
of the CRT projection angle adjustment.
EXIT returns to Raster shift adjustment.
ENTER continues with the second part
of the CRT projection angle adjustment.
EXIT returns to Raster shift adjustment.
CRT PROJECTION ANGLE
ADJUSTMENT
CRT PROJECTION ANGLE
ADJUSTMENT
DURING THIS PROCEDURE,
RED ON GREEN AND THEN
BLUE ON GREEN CROSSHAIRS
WILL BE DISPLAYED
TO ALLOW THE RED AND
BLUE CRTS TO BE ALIGNED
WITH THE GREEN CRT.
DURING THIS PROCEDURE,
RED ON GREEN AND THEN
BLUE ON GREEN CROSSHAIRS
WILL BE DISPLAYED
TO ALLOW THE RED AND
BLUE CRTS TO BE ALIGNED
WITH THE GREEN CRT.
LOOSEN BOLTS A AND B
TO PIVOT THE RED CRT,
AND BOLDS C AND D
TO PIVOT THE BLUE CRT.
<ENTER> to continue
<EXIT> to return
LOOSEN BOLTS A AND B
TO PIVOT THE RED CRT,
AND BOLDS C AND D
TO PIVOT THE BLUE CRT.
<ENTER> to continue
<EXIT> to return
ENTER continues to the crosshairs
alignment.
EXIT returns to raster shift adjustment
ADJUST returns to operational mode.
5975248 BARCOVISION 701 MULTIMEDIA 070597
INSTALLATION ADJUSTMENTS
INSTALLATION ADJUSTMENTS
7-14
CRT PROJECTION ANGLE
ADJUSTMENT
7-14
ENTER continues to the crosshairs
alignment.
EXIT returns to raster shift adjustment
ADJUST returns to operational mode.
5975248 BARCOVISION 701 MULTIMEDIA 070597
INSTALLATION ADJUSTMENTS
Projection angle correctly aligned
for screen width SW1
INSTALLATION ADJUSTMENTS
The same projection angle is mis-aligned for
new screen width SW2. Re-alignment is necessary. Each screen width change requires readjustment of the projection angle.
Projection angle correctly aligned
for screen width SW1
SW1
SW1
SW2
SW2
(SW2>SW1)
INSTALLATION ADJUSTMENTS
INSTALLATION ADJUSTMENTS
(SW2>SW1)
5975248 BARCOVISION 701 MULTIMEDIA 070597
The same projection angle is mis-aligned for
new screen width SW2. Re-alignment is necessary. Each screen width change requires readjustment of the projection angle.
7-15
5975248 BARCOVISION 701 MULTIMEDIA 070597
7-15
INSTALLATION ADJUSTMENTS
A' A
Screws A, B, C and D (M4) : upper
fixation latch. nutdriver 7mm.
Screw A', B', C' and D' (M4) : lower
fixation latch. nutdriver 7mm.
A' A
Loosen the four hexagon screws A, A',
B and B', upper and lower fixation
latch. These screws fasten the cooling house of the red tube.
Pivot the red CRT until the center of
the red image coincides with the center
of the green image. If the angle of the
red CRT is corrected, tighten the four
bolts.
C' C
B B'
C' C
A' A
D D'
Screws A, B, C and D (M4) : upper
fixation latch. nutdriver 7mm.
Screw A', B', C' and D' (M4) : lower
fixation latch. nutdriver 7mm.
A' A
D D'
Loosen the four hexagon screws A,
A', B and B', upper and lower fixation
latch. These screws fasten the cooling house of the red tube.
Pivot the red CRT until the center of
the red image coincides with the center
of the green image. If the angle of the
red CRT is corrected, tighten the four
bolts.
CRT
PROJECTION ANGLE
ADJUSTMENT
Align crosshairs
<ENTER> continue
<EXIT> to return
red crosshair
green crosshair
Move the red CRT to- ENTER continues to blue and green
wards the green CRT crosshairs.
EXIT will return to CRT projection angle
adjustment.
red crosshair
green crosshair
Move the red CRT
to the outside, away
from the green CRT
5975248 BARCOVISION 701 MULTIMEDIA 070597
B B'
C' C
B B'
C' C
D D'
D D'
CRT
PROJECTION ANGLE
ADJUSTMENT
Align crosshairs
<ENTER> continue
<EXIT> to return
INSTALLATION ADJUSTMENTS
INSTALLATION ADJUSTMENTS
7-16
B B'
INSTALLATION ADJUSTMENTS
7-16
red crosshair
green crosshair
Move the red CRT to- ENTER continues to blue and green
wards the green CRT crosshairs.
EXIT will return to CRT projection angle
adjustment.
red crosshair
green crosshair
Move the red CRT
to the outside, away
from the green CRT
5975248 BARCOVISION 701 MULTIMEDIA 070597
INSTALLATION ADJUSTMENTS
blue crosshair
green crosshair
Move the bleu CRT
to the outside, away
from the green CRT
Loosen the four hexagon screws C, C',
Dand D', upper and lower fixation latch.
These screws fasten the cooling house
of the blue tube.
Pivot the blue CRT until the center of the
blue image coincides with the center of
the green image. If the angle of the red
CRT is corrected, tighten the four bolts.
CRT
PROJECTION ANGLE
ADJUSTMENT
Align crosshairs
Align crosshairs
<ENTER> continue
<EXIT> to return
<ENTER> continue
<EXIT> to return
ENTER continues to the path selection menu.
EXIT returns to the CRT projection
angle adjustment.
blue crosshair
green crosshair
Move the bleu CRT
to the outside, away
from the green CRT
blue crosshair
blue crosshair
green crosshair
green crosshair
Move the bleu CRT
towards the green
CRT
Move the bleu CRT
towards the green
CRT
- Guided Adjustment Procedure
- Random Access Adjustment Procedure
The result of both procedures will be
the same. More explanation about
both procedures is given in the owners manual.
The following page gives an overview
of the image corrections.
5975248 BARCOVISION 701 MULTIMEDIA 070597
After finishing the installation adjustments procedure, the 'Path selection'
returns on the screen. You are now
able to start the alignment procedure
for the projector. You have the choice
between :
ADJUSTMENT MODE
GUIDED
RANDOM ACCESS
INSTALLATION
SERVICE
IRIS
source 1
Select with
or
then <ENTER>
<EXIT> to return
INSTALLATION ADJUSTMENTS
After finishing the installation adjustments procedure, the 'Path selection'
returns on the screen. You are now
able to start the alignment procedure
for the projector. You have the choice
between :
CRT
PROJECTION ANGLE
ADJUSTMENT
7-17
- Guided Adjustment Procedure
- Random Access Adjustment Procedure
The result of both procedures will be
the same. More explanation about
both procedures is given in the owners
manual.
The following page gives an overview
of the image corrections.
5975248 BARCOVISION 701 MULTIMEDIA 070597
ENTER continues to the path selection
menu.
EXIT returns to the CRT projection angle adjustment.
ADJUSTMENT MODE
GUIDED
RANDOM ACCESS
INSTALLATION
SERVICE
IRIS
source 1
Select with
or
then <ENTER>
<EXIT> to return
INSTALLATION ADJUSTMENTS
Loosen the four hexagon screws C, C',
Dand D', upper and lower fixation latch.
These screws fasten the cooling house
of the blue tube.
Pivot the blue CRT until the center of
the blue image coincides with the center
of the green image. If the angle of the
red CRT is corrected, tighten the four
bolts.
INSTALLATION ADJUSTMENTS
7-17
INSTALLATION ADJUSTMENTS
INSTALLATION ADJUSTMENTS
Alignment of the projector.
Alignment of the projector.
Overview of the corrections
Overview of the corrections
For detailed information about these corrections and procedures to be followed, see
owner's manual. (pages given hereafter are for the random access adjustment mode)
For detailed information about these corrections and procedures to be followed,
see owner's manual. (pages given hereafter are for the random access adjustment
mode)
Shift corrections for the Red, Green and Blue image.
Shift corrections for the Red, Green and Blue image.
Left-Right adjustments
- Vertical center line bow and skew
- Left and right keystone adjustment
- Left and right bow adjustment
- Horizontal size adjustment
Left-Right adjustments
- Vertical center line bow and skew
- Left and right keystone adjustment
- Left and right bow adjustment
- Horizontal size adjustment
Top-Bottom adjustments
- Horizontal centerline bow and skew
- Top keystone adjustment
- Top bow adjustment
- Bottom keystone adjustment
- Bottom bow adjustment
Top-Bottom adjustments
- Horizontal centerline bow and skew
- Top keystone adjustment
- Top bow adjustment
- Bottom keystone adjustment
- Bottom bow adjustment
Size-linearity adjustments
- Horizontal size adjustment
- Vertical linearity adjustment
- Vertical size adjustment
- Horizontal phase adjustment
Size-linearity adjustments
- Horizontal size adjustment
- Vertical linearity adjustment
- Vertical size adjustment
- Horizontal phase adjustment
Convergence adjustments
- Green only
- Red on green
- Blue on green
Convergence adjustments
- Green only
- Red on green
- Blue on green
Blanking adjustment
- Top-Bottom, Left-Right
Color adjustments
INSTALLATION ADJUSTMENTS
INSTALLATION ADJUSTMENTS
7-18
Blanking adjustment
- Top-Bottom, Left-Right
5975248 BARCOVISION 701 MULTIMEDIA 070597
7-18
Color adjustments
5975248 BARCOVISION 701 MULTIMEDIA 070597
APPENDIX A : CEILING MOUNT KIT CM50
APPENDIX A : CEILING MOUNT KIT CM50
Ceiling mount kit for 700 projectors (CM50).
Ceiling mount kit for 700 projectors (CM50).
This ceiling mount with or without pulley system enables to mount the
BARCO 700 projector to the ceiling. The concept makes it possible to adapt
the projector perfectly to the local mounting requirements in a safe and solid
manner. The ceiling mount is specifically developed for rooms with a lowered
ceiling, but can be used in other rooms as well by omitting the upper plate
and the four screwed rods.
BARCO order no. :
with pulley :R9827990.
without pulley : R9827991
5975248 BARCOVISION 701 MULTIMEDIA 090497
A-1
APPENDIX A : CEILING MOUNT KIT CM50
APPENDIX A : CEILING MOUNT KIT CM50
This ceiling mount with or without pulley system enables to mount the
BARCO 700 projector to the ceiling. The concept makes it possible to adapt
the projector perfectly to the local mounting requirements in a safe and solid
manner. The ceiling mount is specifically developed for rooms with a lowered
ceiling, but can be used in other rooms as well by omitting the upper plate
and the four screwed rods.
BARCO order no. :
with pulley :R9827990.
without pulley : R9827991
5975248 BARCOVISION 701 MULTIMEDIA 090497
A-1
APPENDIX A : CEILING MOUNT KIT CM50
APPENDIX A : CEILING MOUNT KIT CM50
APPENDIX A : CEILING MOUNT KIT CM50
A-2
APPENDIX A : CEILING MOUNT KIT CM50
5975248 BARCOVISION 701 MULTIMEDIA 090497
A-2
5975248 BARCOVISION 701 MULTIMEDIA 090497
APPENDIX B : G2 ADJUSTMENT
APPENDIX B : G2 ADJUSTMENT
G2 adjustment
G2 adjustment
Enter the adjustment mode by pressing
ADJUST and highlight Service. Press
ENTER to start up the service mode.
ADJUSTMENT MODE
Select a path from
below:
ADJUSTMENT MODE
Select a path from
below:
GUIDED
RANDOM ACCESS
INSTALLATION
SERVICE
IRIS
GUIDED
RANDOM ACCESS
INSTALLATION
SERVICE
IRIS
source 1
source 1
Select with
or
then <ENTER>
<EXIT> to return
Select with
or
then <ENTER>
<EXIT> to return
ENTER starts up the service mode.
EXIT returns to operational mode.
Highlight 'Common settings' and press
ENTER.
ENTER starts up the service mode.
EXIT returns to operational mode.
Highlight 'Common settings' and press
ENTER.
SERVICE MODE
PROJECTOR SET-UP
MEMORY MANAGEMENT
COMMON SETTINGS
I2C DIAGNOSTICS
PROJECTOR SET-UP
MEMORY MANAGEMENT
COMMON SETTINGS
I2C DIAGNOSTICS
Select with
or
then <ENTER>
<EXIT> to return.
Select with
or
then <ENTER>
<EXIT> to return.
ENTER starts up the Common settings
menu.
EXIT returns to the adjustment mode
menu.
COMMON SETTINGS
G2 ADJUSTMENT
CRT RUN IN CYCLE
PROJECTOR WARM UP
Select with
or
then <ENTER>
<EXIT> to return.
5975248 BARCOVISION 701 MULTIMEDIA 0070597
ENTER starts up the Common settings
menu.
EXIT returns to the adjustment mode
menu.
APPENDIX B : G2 ADJUSTMENT
Highlight G2 adjust and press ENTER.
A safety notice will be displayed to
warn the operator.
SERVICE MODE
B-1
Highlight G2 adjust and press ENTER.
A safety notice will be displayed to
warn the operator.
COMMON SETTINGS
G2 ADJUSTMENT
CRT RUN IN CYCLE
PROJECTOR WARM UP
Select with
or
then <ENTER>
<EXIT> to return.
5975248 BARCOVISION 701 MULTIMEDIA 070597
APPENDIX B : G2 ADJUSTMENT
Enter the adjustment mode by pressing
ADJUST and highlight Service. Press
ENTER to start up the service mode.
B-1
APPENDIX B : G2 ADJUSTMENT
If you are qualified, press ENTER to
continue with the G2 adjustment, otherwise press EXIT to return to the
service menu.
APPENDIX B : G2 ADJUSTMENT
If you are qualified, press ENTER to
continue with the G2 adjustment, otherwise press EXIT to return to the
service menu.
SAFETY
NOTICE
SAFETY
NOTICE
RISK OF ELECTRICAL SHOCK
RISK OF ELECTRICAL SHOCK
G2 ADJUSTMENT SHOULD BE
PERFORMED
BY BARCO PERSONNEL,
OR BARCO AUTHORIZED
DEALERS.
G2 ADJUSTMENT SHOULD BE
PERFORMED
BY BARCO PERSONNEL,
OR BARCO AUTHORIZED
DEALERS.
IF QUALIFIED, PRESS
<ENTER> TO CONTINUE, OR
IF NOT, <EXIT> TO RETURN.
IF QUALIFIED, PRESS
<ENTER> TO CONTINUE, OR
IF NOT, <EXIT> TO RETURN.
131
131
If ENTER is pressed, the G2 menu will
be displayed.
If ENTER is pressed, the G2 menu will
be displayed.
G2 ADJUSTMENT
G2 ADJUSTMENT
RED
RED
ABL : ON
ABL : ON
Select color with
or
<ENTER> to toggle ABL
<EXIT> to return
Select color with
or
<ENTER> to toggle ABL
<EXIT> to return
Open the top cover to reach the G2 controls and adjust these G2 controls for red,
blue and green separatly.
The controller automatically increases brightness and contrast until the raster
behind the displayed text becomes visible.
Look to the projected image and observe the raster behind the image while the ABL
function is ON.
Look to the projected image and observe the raster behind the image while the ABL
function is ON.
Loosen screws and move the cover plate
to the left to access the G2 controls.
Cover the G2 controls again after alignment.
G2 Adjustments
Red
Green
Blue
5975248 BARCOVISION 701 MULTIMEDIA 070597
APPENDIX B : G2 ADJUSTMENT
APPENDIX B : G2 ADJUSTMENT
B-2
Open the top cover to reach the G2 controls and adjust these G2 controls for red,
blue and green separatly.
The controller automatically increases brightness and contrast until the raster
behind the displayed text becomes visible.
B-2
Loosen screws and move the cover plate
to the left to access the G2 controls.
Cover the G2 controls again after alignment.
G2 Adjustments
Red
Green
Blue
5975248 BARCOVISION 701 MULTIMEDIA 070597
APPENDIX B : G2 ADJUSTMENT
APPENDIX B : G2 ADJUSTMENT
Switch ABL to OFF by pressing ENTER and adjust the G2 control until the raster
brightness looks the same as when the ABL function is ON.
Check the correct raster adjustment by pressing ENTER to toggle ABL to ON.
Repeat these steps if necessary.
Check the correct raster adjustment by pressing ENTER to toggle ABL to ON.
Repeat these steps if necessary.
Continue with the other colors. Use the right or left arrow key to select the next
color.
Continue with the other colors. Use the right or left arrow key to select the next
color.
Note : The best result is obtained in a completly dark room or by looking into the
lenses, but be aware that brightness and contrast are on a high level.
Note : The best result is obtained in a completly dark room or by looking into the
lenses, but be aware that brightness and contrast are on a high level.
APPENDIX B : G2 ADJUSTMENT
APPENDIX B : G2 ADJUSTMENT
Switch ABL to OFF by pressing ENTER and adjust the G2 control until the raster
brightness looks the same as when the ABL function is ON.
5975248 BARCOVISION 701 MULTIMEDIA 0070597
B-3
5975248 BARCOVISION 701 MULTIMEDIA 070597
B-3
APPENDIX B : G2 ADJUSTMENT
APPENDIX B : G2 ADJUSTMENT
APPENDIX B : G2 ADJUSTMENT
B-4
APPENDIX B : G2 ADJUSTMENT
5975248 BARCOVISION 701 MULTIMEDIA 070597
B-4
5975248 BARCOVISION 701 MULTIMEDIA 070597