Aussie Joey 7110 Series Technical information

Acer
Aspire 9420/ 9410/ 7110
TravelMate 5620/ 5610/ 5110
Service Guide
Service guide files and updates are
available on the ACER/CSD web. For
more information, please refer to http://
csd.acer.com.tw
PRINTED IN TAIWAN
II
Revision History
Please refer to the table below for the updates of Aspire 9420/ 9410/ 7110 and TravelMate 5620/ 5610/ 5110
service guide.
Date
September 29, 2006
Chapter
Updates
first release
III
Copyright
Copyright© 2006 by Acer Incorporated. All rights reserved. No part of this publication may be reproduced,
transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in
any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without
the prior written permission of Acer Incorporated.
IV
Disclaimer
The information in this guide is subject to change without notice.
Acer Incorporated makes no representations or warranties, either expressed or implied, with respect to the
contents hereof and specifically disclaims any warranties of merchantability or fitness for any particular
purpose. Any Acer Incorporated software described in this manual is sold or licensed “as is”. Should the
programs prove defective following their purchase, the buyer (and not Acer Incorporated, its distributor, or its
dealer) assumes the entire cost of all necessary servicing, repair, and any incidental or consequential
damages resulting from any defect in the software.
Acer is a registered trademark of Acer Incorporated.
Intel is a registered trademark of Intel Corporation.
Pentium and Pentium D are trademarks of Intel Corporation.
Other brand and product names are trademarks and/or registered trademarks of their respective holders.
V
Conventions
The following conventions are used in this manual:
VI
SCREEN MESSAGES
Denotes actual messages that appear on screen.
NOTE
Gives bits and pieces of additional information related to the
current topic.
WARNING
Alerts you to any damage that might result from doing or not
doing specific actions.
CAUTION
Gives precautionary measures to avoid possible hardware
or software problems.
IMPORTANT
Reminds you to do specific actions relevant to the
accomplishment of procedures.
Preface
Before using this information and the product it supports, please read the following general information.
1. This Service Guide provides you with all technical information relating to the BASIC
CONFIGURATION decided for Acer's “global” product offering. To better fit local market
requirements and enhance product competitiveness, your regional office MAY have decided to
extend the functionality of a machine (e.g. add-on card, modem, or extra memory capability).
These LOCALIZED FEATURES will NOT be covered in this generic service guide. In such
cases, please contact your regional offices or the responsible personnel/channel to provide you
with further technical details.
2. Please note WHEN ORDERING FRU PARTS, you should check the most up-to-date information
available on your regional web or channel. For whatever reason, if a part number change is
made, it will not be noted in the printed Service Guide. For ACER-AUTHORIZED SERVICE
PROVIDERS, your Acer office may have a DIFFERENT part number code to those given in the
FRU list of this printed Service Guide. You MUST use the list provided by your regional Acer
office to order FRU parts for repair and service of customer machines.
VII
Table of Contents
Chapter One System Specification 1
Specification . . . . . . . . . . . . . . . . . . . . . . . 1
Operating System . . . . . . . . . . . . . . . . . . . . . .
Platform . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
System Memory . . . . . . . . . . . . . . . . . . . . . . .
Display and Graphics . . . . . . . . . . . . . . . . . . .
Storage Subsystem . . . . . . . . . . . . . . . . . . . . .
Input Devices . . . . . . . . . . . . . . . . . . . . . . . . . .
Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Communication . . . . . . . . . . . . . . . . . . . . . . .
I/O Interface . . . . . . . . . . . . . . . . . . . . . . . . . .
Power Subsystem . . . . . . . . . . . . . . . . . . . . . .
Dimensions and Weight . . . . . . . . . . . . . . . . .
Environment . . . . . . . . . . . . . . . . . . . . . . . . . .
1
1
2
2
2
2
2
3
3
3
3
4
Block Diagram . . . . . . . . . . . . . . . . . . . . . . 5
Outlook Tour . . . . . . . . . . . . . . . . . . . . . . . 6
Front View . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Closed Front View . . . . . . . . . . . . . . . . . . . . . . 7
Left View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Right View . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Rear View . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Base View . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Windows keys . . . . . . . . . . . . . . . . . . . . . . . . 11
Hotkeys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Special keys . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Indicators . . . . . . . . . . . . . . . . . . . . . . . . . 13
Easy-launch Buttons . . . . . . . . . . . . . . . . 14
Touchpad . . . . . . . . . . . . . . . . . . . . . . . . . 15
Touchpad Basics . . . . . . . . . . . . . . . . . . . . . . 15
Acer Empowering Technology . . . . . . . . 16
Empowering Technology Password . . . . . . .
Acer eDataSecurity Management . . . . . . . .
Acer eLock Management . . . . . . . . . . . . . . .
Acer ePerformance Management . . . . . . . .
Acer eRecovery Management . . . . . . . . . . .
Acer eSettings Management . . . . . . . . . . . .
Acer eNet Management . . . . . . . . . . . . . . . .
Acer ePower Management . . . . . . . . . . . . .
Acer ePresentation Management . . . . . . . .
16
17
19
20
21
22
23
25
27
Acer OrbiCam . . . . . . . . . . . . . . . . . . . . . 28
TOC
VIII
Rotating the Acer Orbicam . . . . . . . . . . . . . 28
Launching the Acer OrbiCam (for 1.3 megapixel camera models only)
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Changing the Acer OrbiCam Settings . . . . . 29
Capturing Photos or Videos . . . . . . . . . . . . . 31
Using the Acer OrbiCam as Webcam . . . . . . 31
Enabling the Acer VisageON (for 1.3 megapixel camera models only)
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Using the System Utilities . . . . . . . . . . . . 34
Acer GridVista (dual-display compatible) . . 34
Launch Manager . . . . . . . . . . . . . . . . . . . . . . 35
Norton AntiVirus . . . . . . . . . . . . . . . . . . . 36
How do I check for viruses? . . . . . . . . . . . . . 36
Hardware Specification and Configuration
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Chapter Two System Utilities 46
BIOS Setup Utility . . . . . . . . . . . . . . . . . . 46
Invoking BIOS Setup . . . . . . . . . . . . . . . . . . . 46
Information . . . . . . . . . . . . . . . . . . . . . . .
Main . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Security . . . . . . . . . . . . . . . . . . . . . . . . . .
Boot . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
47
48
50
52
53
Chapter Three Machine Disassembly and Replacement 54
General Information . . . . . . . . . . . . . . . . 55
Before You Begin . . . . . . . . . . . . . . . . . . . . . 55
Disassembly Procedure Flowchart . . . . . 56
Disassembly Procedure . . . . . . . . . . . . . . 58
Removing the Battery Pack . . . . . . . . . . . . . 58
Removing the HDD Module . . . . . . . . . . . . . 58
Removing the MiniPCI Card and the Memory
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Removing the Keyboard . . . . . . . . . . . . . . . 59
Separating the LCD Module and Main Unit 61
Disassembling the Main Unit . . . . . . . . . . . . 62
LCD Disassembly . . . . . . . . . . . . . . . . . . . . . . 68
IX
TOC
Chapter Four Troubleshooting 72
System Check Procedures . . . . . . . . . . . . 73
External Diskette Drive Check . . . . . . . . . . .
External CD-ROM Drive Check . . . . . . . . . . .
Keyboard or Auxiliary Input Device Check .
Memory Check . . . . . . . . . . . . . . . . . . . . . . .
Power System Check . . . . . . . . . . . . . . . . . . .
Check the Power Adaptor . . . . . . . . . . . . . .
Check the Battery Pack . . . . . . . . . . . . . . . . .
Touchpad Check . . . . . . . . . . . . . . . . . . . . . .
73
73
73
73
74
74
74
75
Power-On Self-Test (POST) Error Message
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
Index of Error Messages . . . . . . . . . . . . . 77
Error Message List . . . . . . . . . . . . . . . . . . . . . 77
Phoenix BIOS Beep Codes . . . . . . . . . . . . 78
Index of Symptom-to-FRU Error Message
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Intermittent Problems . . . . . . . . . . . . . . 86
Undetermined Problems . . . . . . . . . . . . . 87
Chapter Five Jumper and Connector Location 88
Top View . . . . . . . . . . . . . . . . . . . . . . . . . 88
Bottom View . . . . . . . . . . . . . . . . . . . . . . 90
Chapter Six FRU (Field Replaceable Unit) List 91
Exploded Diagram . . . . . . . . . . . . . . . . . 92
Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
TOC
X
Chapter 1
System Specification
Specification
Operating System
Aspire Series
•
Genuine Windows® XP Home Edition (SP2)
•
Genuine Windows® XP Professional (SP2)
•
Genuine Windows® XP Media Center Edition 2005 (Rollup 2)
•
Genuine Windows® XP Professional x64 Edition (for Aspire 9420 series)
TravelMate Series
•
Windows® VistaTM Capable
•
Genuine Windows® XP Home Edition (SP2)
•
Genuine Windows® XP Professional (SP2)
•
Genuine Windows® XP Professional x64 Edition (for TravelMate 5620 series)
Note: Windows® VistaTM Capable PCs come with Windows® XP installed, and can be upgraded to Windows®
VistaTM. For more information on Windows® and how to upgrade, go to: Microsoft.com/windowsvista.
Platform
Aspire 9420 & TravelMate 5620 Series
Intel® Centrino® Duo mobile technology, featuring:
•
Intel® CoreTM 2 Duo processor T7200/T7400/T7600 (4MB L2 cache, 2.0/ 2.16/ 2.33GHz, 667MHz FSB)
and T5500/T5600 (2MB L2 cache, 1.66/ 1.83GHz, 667MHz FSB), supporting Intel® EM64T
•
Mobile Intel® 945GM/PM Express chipset
•
Intel® PRO/Wireless 3945ABG network connection (dual-band tri-mode 802.11a/b/g) Wi-Fi CERTIFIEDTM
solution, supporting Acer SignalUpTM wireless technology
Aspire 9410 & TravelMate 5610 Series
•
Intel® CoreTM Duo processor T2300/T2400/T2500/T2600 (2MB L2 cache, 1.66/1.83/2/2.16GHz, 667MHz
FSB)
•
Mobile Intel® 945GM/PM Express chipset
•
Intel® PRO/Wireless 3945ABG network connection (dual-band tri-mode 802.11a/b/g) Wi-Fi CERTIFIEDTM
solution, supporting Acer SignalUpTM wireless technology
Aspire 7110 & TravelMate 5110 Series
•
Intel® Celeron® M processor 410/420/430 (1MB L2 cache, 1.46/1.60/1.73GHz, 533MHz FSB)
•
Mobile Intel® 940GML Express chipset
•
Acer InviLinkTM 802.11b/g Wi-Fi CERTIFIEDTM solution, supporting Acer SignalUpTM wireless technology
Chapter 1
1
System Memory
•
Up to 2GB of DDR2 533/667MHz memory, upgradeable to 4GB using two soDIMM modules (dualchannel support) (for Aspire 9420/ 9410 & TravelMate 5620/ 5610 series)
•
Up to 1GB of DDR2 533MHz memory, upgradeable to 2GB using two soDIMM modules (dual-channel
support) (for Aspire 7110 & TravelMate 5110 series)
Display and Graphics
•
17.1” WXGA + 200-nit Acer CrystalBriteTM color TFT LCD (for Aspire 9420/ 9410/ 7110 series) or high
brightness TFT LCD (for TravelMate 5620/ 5610/ 5110 series), 1440 x 900 pixel resolution, supporting
simultaneous multi-window viewing via Acer GridVistaTM
•
NVIDIA® GeForce® Go 7300 up to 512MB TurboCacheTM (256MB of dedicated GDDR2 VRAM, 256MB of
shared system memory), supporting Microsoft® DirectX® 9.0, Shader Model 3.0, OpenEXR High Dynamic
Range (HDR) technology, NVIDIA® PowerMizerTM 6.0, PCI Express®, or
•
Mobile Intel® 945GM/940GML Express chipset (for Aspire 9420/ 9410/ 7110 series) or 945GM Express
chipset (for TravelMate 5620/ 5610/ 5110 series) with integrated 3D graphics, featuring Intel® Graphics
Media Accelerator (GMA) 950, up to 224MB of shared system memory, supporting Microsoft® DirectX®
9.0 and PCI Express® and dual independent displays
•
16.7 million colors
•
MPEG-2/DVD hardware-assisted capability
•
S-video/TV-out (NTSC/PAL) support (for Aspire 9420/ 9410/ 7110 series)
•
Acer CinemaVisionTM technology (Acer ArcadeTM) (for Aspire 9420/ 9410/ 7110 series)
•
Acer ClearVisionTM technology (Acer ArcadeTM) (for Aspire 9420/ 9410/ 7110 series)
Note: TurboCacheTM memory allocation varies depending on configuration.
Storage Subsystem
•
60/80/100/120GB or higher hard disk drive (Aspire 9420/ 9410/ 7110 series)
•
80/100/120GB or higher hard disk drive with Acer Disk Anti-Shock Protection, DASP (TravelMate 5620/
5610/ 5110 series)
•
Optical drive options:
•
•
DVD-Super Multi double-layer
•
DVD-Dual double-layer
•
DVD/CD-RW combo drive
5-in-1 card reader, supporting Secure Digital (SD), MultiMediaCard (MMC), Memory Stick® (MS), Memory
Stick PROTM (MS PRO), xD-Picture CardTM (xD)
Input Devices
•
105-/106-key keyboard
•
Touch pad with 4-way scroll button
•
Four easy launch buttons
•
Two LED-buttons: WLAN, Bluetooth®
Audio
2
•
Audio system with two built-in speakers
•
Intel® high definition audio support
•
Sound Blaster PROTM and MS Sound compatible
•
S/PDIF (Sony/Philips Digital Interface) support for digital speakers.
Chapter 1
•
Built-in microphone
Communication
•
Acer Video Conference featuring Voice and Video over internet Protocol (VVoIP) support via Acer
OrbiCamTM and optional Acer Bluetooth® VoIP phone
•
Acer OrbiCamTM integrated 1.3 megapixel or 310,000 pixel CMOS camera (for selected models),
featuring:
•
225 degree ergonomic rotation
•
Acer VisageONTM technology (for 1.3 megapixel camera models only)
•
Acer PrimaLiteTM technology
•
Modem: 56K ITU V.92 with PTT approval; Wake-on-Ring ready
•
LAN: gigabit Ethernet; Wake-on-LAN ready
•
WPAN: Bluetooth® 2.0 + EDR (Enhanced Data Rate)
•
WLAN: Intel® PRO/Wireless 3945ABG network connection (dual-band tri-mode 802.11a/b/g) Wi-Fi
CERTIFIEDTM solution, supporting Acer SignalUpTM wireless technology (Aspire 9420/ 9410 &
TravelMate 5620/ 5610 series)
•
WLAN: Integrated Acer InviLinkTM 802.11b/g Wi-Fi CERTIFIEDTM solution, supporting Acer SignalUpTM
wireless technology (Aspire 7110 & TravelMate 5110 series)
I/O Interface
•
PC Card slot (one Type II)
•
Four USB 2.0 ports
•
External display (VGA) port
•
S-video/TV-out (NTSC/PAL) port (for Aspire 9420/ 9410/ 7110 series)
•
Headphones/speaker/line-out jack with S/PDIF support
•
Microphone-in jack
•
Line-in jack
•
Ethernet (RJ-45) port
•
Modem (RJ-11) port
•
DC-in jack for AC adapter
Power Subsystem
•
ACPI 2.0 CPU power management standards: Stand-by and Hibernation power-saving modes support
•
71W 4800mAh (8-cell) or 44W 4000mAh (6-cell) Li-Ion battery pack
•
Acer QuicChargeTM technology: 80% charge in 1 hour; 2-hour rapid charge system-off; 2.5-hour chargein-use
•
3-pin 90W AC adapter
Dimensions and Weight
•
•
With Acer OrbiCamTM
•
400 (W) x 295 (D) x 31.4/39.9 (H) mm (15.75 x 11.61 x 1.24/1.57 inches)
•
3.81 kg (8.39 lbs.) with 8-cell battery pack
•
3.68 kg (8.10 lbs.) with 6-cell battery pack
Without Acer OrbiCamTM
•
400 (W) x 295 (D) x 31.4/39.9 (H) mm (15.75 x 11.61 x 1.24/1.57 inches)
•
3.79 kg (8.35 lbs.) with 8-cell battery pack
Chapter 1
3
•
3.66 kg (8.06 lbs.) with 6-cell battery pack
Environment
•
•
4
Temperature
•
Operating: 5 oC to 35 oC
•
Non-operating: -20 oC to 65 oC
Humidity (non-condensing)
•
Operating: 20% to 80%
•
Non-operating: 20% to 80%
Chapter 1
Block Diagram
Chapter 1
5
Outlook Tour
Just for Starters...
"Launch keys" on page 10
Front View
Aspire 9420/ 9410/ 7110 Series
#
Item
Just for Starters...
TravelMate 5620/ 5610/ 5110 Series
Description
"Launch keys" on page 10
#
Icon
#
Icon
Item
6
Icon
Item
Item
Description
Description
#
Icon Description
Item
1
N/A
Built-in camera
1.3 megapixel or 310,000 pixel web camera for video
communication (for selected models)
2
N/A
Display screen
Also called Liquid-Crystal Display (LCD), displays computer
output.
3
N/A
Status indicators
Light-Emitting Diodes (LEDs) that light up to show the status
of the computer’s functions and components.
4
Wireless communication
button
Enable/disables Wireless function. Indicates the status of
wireless LAN communications.
5
Bluetooth communication
button
Enable/disables Bluetooth function. Indicates the status of
Bluetooth communications.
#
Icon
Item
Description
Description
6
N/A
Microphone
Internal microphone for sound recording
7
N/A
Touchpad
Touch-sensitive pointing device which functions like a
computer mouse
8
N/A
Click buttons (left, center
and right)
The left and right buttons function like the left and right mouse
buttons; the center button serves as a 4-way scroll button.
Chapter 1
#
#
Item
#
Description
Item
Description
#9
#
Icon
N/A
Item
10
N/A
Keyboard
11
N/A
Power button
12
N/A
Item
#
Item
Palmrest
Description
Comfortable support area for your hands when you use the
Description
computer.
For entering data into your computer.
"Launch
on
10
Turns thekeys"
computer on
and page
off.
Easy launch buttons
Buttons for launching frequently used programs.
Description
"Launch keys" on page 10
"Easy-launch buttons" on
page 27
Closed Front
View"Launch keys" on page 10
Aspire 9420/ 9410/ 7110 Series
"Easy-launch buttons" on
page 27
TravelMate 5620/ 5610/ 5110 Series
"Launch keys" on page 10
Icon
Item
#
#
#
1
2
#
#
Icon
Icon
Icon
N/A
Icon
3
Icon
#
Icon
#
4
Icon
Description
Item
Item
Description
#
Icon
Item
Description
Description
Item
Speakers
Description
Left and right speakers
deliver stereo audio output.
Line-in jack
Accepts audio line-in devices (e.g., audio CD player, stereo
walkman).Description
Item
Item
Description
Microphone-in jack
Item
Accepts input from external microphones.
Description
Item
Headphones/speaker/
line-out jack with S/PDIF
support
Description
Connects to audio line-out devices (e.g., speakers,
headphones).
5
Power indicator
Indicates the computer’s power status.
6
Battery indicator
Indicates the computer’s battery status.
Note:
7
Bluetooth communication
indicator
Indicates the status of Bluetooth communication.
8
Wireless communication
indicator
Indicates the status of wireless LAN communication.
Latch
Locks and releases the lid.
9
Chapter 1
N/A
7
#
Icon
Item
Description
Left View
Aspire 9420/ 9410/ 7110 Series
#
Icon
Item
TravelMate 5620/ 5610/ 5110 Series
Description
#
Icon
Item
1
Kensington lock slot
#
2
Icon
Item
#
Icon
Item
#
Icon
Item
Description
Description
Description
Connects to a Kensington-compatible computers security lock.
Description
N/A
Optical disk drive
Item
Description
3
N/A
Optical disk access
indicator
Lights up when the optical disk drive is active.
4
N/A
Optical disk drive eject
button
Ejects the drive tray from the drive (location depends on
model).
5
N/A
Emergency eject hole
Ejects the drive tray when the computer is turned off.
#
Internal optical drive; accepts CDs or DVDs (slot-load or trayload depending on model).
Note:
"Easy-launch buttons" on page 10
Note:
Right View
Aspire 9420/ 9410/ 7110 Series
#
Icon
Item
2
Icon
#
Icon
N/A
Icon
3
#
5#
8
Item
Icon
Item
#
Icon
Item
Description
Icon
PC Card slot
Description
Item
Three USB 2.0 ports
Icon
N/A
Description
Description
Item
PC Card slot
eject button Description
Ejects the PC Card from the slot.
Item
5-in-1 card reader
4
6
#
Description
#
1#
TravelMate 5620/ 5610/ 5110 Series
Accepts one Type II PC Card.
Accepts Memory Stick (MS), Memory Stick Pro (MS PRO),
MultiMediaCard (MMC), Secure Digital (SD) and xD-Picture
Note:
Card (xD).
Description
Connect to USB 2.0 devices (e.g., USB mouse, USB camera).
Item
Ventilation slots Description Enable the computer to stay cool, even after prolonged use.
DC-in jack
Connects to an AC adapter.
Chapter 1
Note:
Rear View
Aspire 9420/ 9410/ 7110 Series
Icon
Item
#
##
#
1
#
Icon
Icon Description
Item
Icon
Item
Icon
Icon
2
#
2
TravelMate 5620/ 5610/ 5110 Series
Item
Description
Description
Description
Item
#
USB 2.0 ports
Item
Item
Description
Item
Description
Connect to USB 2.0 devices (e.g., USB mouse, USB camera).
Description
S-video/TV-out (NTSC/
PAL) port
Icon
Icon
Connects to a television or display device with S-video input.
Note:
Description
External display (VGA) port Connects to an external display device (e.g., external monitor,
LCD projector).
3
Modem (RJ-11) port
Connects to a phone line.
4
Ethernet (RJ-45) port
Connects to an Ethernet 10/100/1000-based networks.
Battery
Powers the computer.
5
N/A
#
Icon
#
Chapter 1
Icon
Item
Item
Description
Description
9
Base View
Upper: Aspire 9420/ 9410/ 7110 Series
Lower: TravelMate 5620/ 5610 /5110 Series
#
Item
Description
Note
#
Icon
1
N/A
Item
2
N/A
Cooling fan
3
N/A
Mini PCI card bay
Houses the computer’s Mini PCI card.
4
N/A
Ventilation slots
Enable the computer to stay cool, even after prolonged use.
5
N/A
Memory compartment
Houses the computer’s main memory.
6
N/A
PCI Express Mini Card bay
Houses the computer’s PCI Express Mini card.
7
N/A
Hard disk bay
Houses the computer’s hard disk (secured with screws).
8
N/A
Battery lock
Locks the battery in position.
9
N/A
Battery bay
Houses the computer’s battery pack.
8
N/A
Acer DASP (Disk AntiShock Protection)
Protects the hard disk drive from shocks and bumps.
(TravelMate 5620/ 5610/ 5110 series)
9
N/A
Battery lock
Locks the battery in position.
10
N/A
Battery bay
Houses the computer’s battery pack.
#
Item
Battery release latch
Description
Description
Releases the battery for removal.
Helps keep the computer cool.
Note Note: Do not cover or obstruct the opening of the fan.
10
Chapter 1
Windows keys
The keyboard has two keys that perform Windows-specific functions.
Key
Windows key
Key
Description
Icon
Description
Description
Press
alone. This key has the same effect as clicking on the Windows
Key
Start button. It launches the Start menu. It can also be used with other
keys to provide a variety of functions:
+ Tab: Activates the next Taskbar button.
<
+ <Tab>:
+> E:
Opens the My Computer window.
<
+ <E>:
+> F1:
Opens Help and Support.
<
<
> + <F1>:
<
> + <Tab>:
<
> + <E>:
+ F: Opens the Find (All Files dialog box).
> + <F>:
+ R:
Opens the Run dialog box.
+ <R>:
<
+ <M>:
+> M:
Minimizes all windows.
<Shift> + <
Shift +
Application key
> + <M>:
<
> + <F1>:
+ M: Undoes the minimize all windows action.
This key has the same effect as clicking the right mouse button. It
opens the application’s context menu.
<
> + <F>:
+ <R>:
Hotkeys
<
> + <M>:
The computer employs hotkeys or key combinations to access most of the computer's controls like screen
brightness, volume output and the BIOS utility. To activate hotkeys, press and hold the <Fn> key before pressing
<Fn>
the other key in the hotkey combination.
<Shift> + <
Hotkey
Icon
<Fn>
+ <F1>
Hotkey
Icon
Function
> + <M>:
Description
Function
Description
<Fn> + <F1>
Hotkey
Icon
Hotkey
Icon
<Fn> + <F2>
Function
Description
Function
Description
Function Description
Description
Function
Icon
Function
Description
<Fn> + <F1> Icon
Hotkey
Hotkey
Icon
Key
<Fn>
+<F2>
<F1>
<Fn>
+Hot
<Fn> <Fn>
+ Fn
<F1>
++ <F1>
F1
page 20
Hot key help
Displays help on hot keys.
+ <F2>
<Fn> <Fn>
+ <F3>
<Fn> + <F2>
Fn++ <F2>
F2
<Fn>
<Fn>
+ <F3>
<Fn>
+ <F2>
<Fn><Fn>
+Fn<F4>
<Fn>
<F3>
++F3
<F3>
"Acer eManager"
"Acer eManager" on
page 20
"Acer
eManager"
Launches
the Acer
eSettingson
in
"Acer
eManager"
onAcer
page
20
Empowering
Technology.
page 20
"Acer eManager" on
Acer eSetting
page 20
<Fn>
"Acer eManager"
on
Acer ePower
Management
Launches the Acer ePower Management in Acer
page 20
Empowering
Technology.
Sleep
Leads the computer to Sleep mode.
+ <F5>
<Fn> <Fn>
+<Fn>
<F4>
+ <F5>
Display toggle
Switches the display output between the display
screen, external monitor (if connected) and both.
<Fn> +Fn<F6>
+ F6
Screen blank
Turns off the display screen backlight to save
power. Press any key to return.
<Fn> + <F3>
<Fn> + <F4>
<Fn> +
<F3>
++F4
<F4>
<Fn>
<F4>
<Fn><Fn>
+Fn<F5>
<Fn> + <F4>
<Fn>
+ +<F5>
<Fn>
<F5>
Fn
F5
<Fn> + <F6>
<Fn>
+
<F5>
<Fn>
+<F6>
<F6>
<Fn>
<Fn>
+ +<F6>
Chapter
<Fn>
+1 <F7>
<Fn>
+ <F7>
<Fn>
<Fn>++<F7>
<F7>
11
<Fn> + <F5>
<Fn> + <F6>
<Fn>
<F6>
<Fn>++<F7>
<F6>
<Fn>
<Fn>
<F7>
<Fn>
++
<F6>
Hot Key
Icon
<Fn>
<F7>
<Fn>
<F7>
+<F8>
F7
<Fn>
++<F7>
<Fn>
+Fn
<Fn>
+<F7>
<Fn> + <F8>
<Fn>
+<F8>
<F8>
Fn
+ <F8>
F8
<Fn>
++
<Fn>
<Fn>
<Fn>++<< >>
Function
Description
Touchpad toggle
Turns the internal touchpad on and off.
Speaker toggle
Turns the speakers on and off.
Volume up
Increases the sound volume.
Volume down
Decreases the sound volume.
Brightness up
Increases the screen brightness.
Brightness down
Decreases the screen brightness.
<Fn> + <F8>
<Fn>
<Fn>
+ +<
Fn
+<
K>>
<Fn> + < >
<Fn>++<< >>
<Fn>
<Fn>
+Fn
+<
L>
<Fn>
+<+<
>>
<Fn>
<Fn> + < >
<Fn> + < >
+<J >
<Fn>Fn
>
<Fn>
++<
<Fn> + <
<Fn>
<Fn>
+ <+ <>
>
>
<Fn>
++
<
<Fn>
Fn
+<
I >>
<Fn>
<Fn>++<< >>
<Fn> + <
<Fn> + <
>
>
Special keys
You can locate the Euro symbol and the US dollar sign on the upper-center and/or bottom-right side of the
keyboard.
<Fn> + <
>
The Euro Symbol
1. Open a text editor or word processor.
2. Either directly press the Euro key on the bottom-right side of the keyboard, or hold Alt Gr key then press the
Euro symbol on the number five key.
Alt Gr>
Note: Some fonts and software do not<5>
support the Euro symbol. Please refer to www.microsoft.com/
typography/faq/faq12.htm for more information.
The US Dollar Sign
Note
www.microsoft.com/typography/faq/faq12.htm
1. Open a text editor or word processor.
2. Either directly press the $ key on the bottom-right side of the keyboard, or hold Shift and then press the US
dollar sign on the number four key.
Note: This function varies according to the language settings.
<Shift>
<4>
Note:
12
Chapter 1
Indicators
#
Item
Description
The computer provides an array of three indicators located above the keyboard, in addition to four indicators on
the front cover. These indicators show the status of the computer and its components.
#
#
Item
Description
Item
Description
"Launch keys" on page 10
"Launch keys" on page 10
"Launch keys" on page 10
#
Item
Description
"Launch keys" on page 10
The front panel indicators are visible even when the computer cover is closed up.
Icon
Icon
#
#
#
Icon
Item
Icon
Item
Icon
#
Chapter 1
Function
Icon
Item
HDD
ItemCaps Lock
Item
Description
Description
Description
Indicates when the hard disk drive is active.
Description
Lights up when
Caps Lock is activated.
Description
Num LockDescription
Lights up when Num Lock is activated.
Power
Lights when the computer is on.
Battery
Lights when the battery is being charged.
Bluetooth
Indicates the status of Bluetooth communication
Wireless LAN
Indicates the status of wireless LAN communication
13
2. Fully charged:
Easy-launch Buttons
There are several conveniently located easy-launch buttons. They are one user-programmable button, web
"
browser button, mail button, and Acer Empowering Key
. Press
to run the
Acer Empowering Technology.
Although the mail and web browser buttons are pre-set to E-mail and Internet programs, they can be redefined by
users. To set the web browser, mail and programmable buttons, run the Acer Launch Manager.
"Launch Manager" on page 44
"Easy-launch
buttons"
"Easy-launch buttons"
on page
10 on page 10
Easy-launch button
Easy-launch button
Default application
Default
Acer application
Empowering Technology (user-programmable)
Mail
E-mail application (user-programmable)
Web browser
Internet browser (user-programmable)
P
User-programmable
"Easy-launch buttons" on page 10
14
Chapter 1
Touchpad
The built-in touchpad is a pointing device that senses movement on its surface. This means the cursor responds
as you move your finger across the surface of the touchpad. The central location on the palmrest provides
optimum comfort and support.
Touchpad Basics
Use the touchpad as follows:
(2)
(2)
•
Move your
the cursor.
(1)
(4)
(1)finger across
(4) the touchpad (2) to move
•
Press the left (1) and right (4) buttons located on the edge of the touchpad to perform selection and
execution functions. These two buttons are similar to the left and right buttons on a mouse. Tapping on the
touchpad (2) is the same as clicking the left button.
•
(3)scroll (3) button to scroll up or down and move left or right a page. This button mimics
Use the four-way
your cursor pressing on the right scroll bar of windows applications.
(3)
Function
Execute
Left button (1)
Right button (4)
Quickly click
twice.
Main touchpad (2)
Tap twice (at the
same speed as
double-clicking a
mouse button).
Select
Click once
Tap once
Drag
Click and hold.
Then slide your
finger across the
touchpad to
drag the cursor
over the
selection.
Tap twice (at the
same speed as
double-clicking a
mouse button); rest
your finger on the
touchpad on the
second tap and
drag the cursor.
Access context
menu
Scroll
Center button (3)
Click once
Click and hold to
move up/down/
left/right.
Note: Keep your fingers, as well as the surface of the touchpad dry and clean. The touchpad is sensitive to
your finger movements: the lighter the touch, the better the response. Tapping hard will not increase the
touchpad’s responsiveness.
Note: By default, vertical and horizontal scrolling is enabled on your touchpad. It can be disabled under Mouse
settings in Windows Control Panel.
Chapter 1
15
Acer Empowering Technology
Acer’s innovative Empowering Technology makes it easy to have access to the frequently used functions and
manage the notebook. It features the following handy utilities:
•
Acer eDataSecurity Management protects data with passwords and advanced encryption algorithms.
•
Acer eLock Management limits access to external storage media.
•
Acer ePerformance Management improves system performance by optimizing disk space, memory and
registry setting.
•
Acer eRecovery Management backs up and recovers data flexibly, reliably and completely.
•
Acer eSettings Management accesses system information and adjusts settings easily.
•
Acer eNet Management hooks up to location-based networks intelligently.
•
Acer ePower Management extends battery power via versatile usage profiles.
•
Acer ePresentation Management connects to a projector and adjusts dispaly settings conveniently.
For more information, press the
key to launch the Empowering Technology menu, then click on the appropriate
utility and select the Help function.
Empowering Technology Password
Before using Acer eLock Management and Acer eRecovery Management, you must initialize the Empowering
Technology password. Right-click on the Empowering Technology tool bar and select Password Setup to do so. If
you do not initialize the Empowering Technology password, you will be prompted to do so when running Acer
eLock Management or Acer eRecovery Management for the first time.
Note: If you lose the password, there is no method to reset it except by reformatting your system or taking
your notebook to an Acer Customer Service Center. Be sure to remember or write down your password.
"Easy-launch buttons" on page 10
16
Chapter 1
Acer eDataSecurity Management
Acer eDataSecurity Management is a handy file encryption utility that protects the files from being accessed by
unauthorized persons. It is conveniently integrated with Windows Explorer as a shell extension for quick and easy
data encryption and decryption and also supports on-the-fly file encryption for MSN Messenger and Microsoft
Outlook.
There are two passwords that can be used to encrypt and decrypt a file: the supervisor password and the filespecific password. The supervisor password is a “master” password that can decrypt any file on the system. The
file-specific password is assigned when you encrypt each individual file.
Acer eDataSecurity Management setup wizard will prompt for a supervisor password and default file-specific
password. This file-specific password will be used to encrypt files by default, or you can choose to enter your own
file-specific password when encrypting a file.
Note: The password used to encrypt a file is the unique key that the system needs to decrypt it. If you lose the
password, the supervisor password is the only other key capable of decrypting the file. If you lose both
passwords, there will be no way to decrypt the encrypted files! Be sure to safeguard all related
password.
Chapter 1
17
18
Chapter 1
Acer eLock Management
Acer eLock Management is a security utility that allow you to lock up your removable data, optical and floppy
drives to ensure that data can not be stolen while your notebook is unattended.
•
Removable data devices: includes USB disk drives, USB pen drives, USB flash drives, USB MP3 drives,
USB memory card readers, IEEE 1394 disk drives and any other removable disk drives that can be
mounted as a file system when plugged into the system.
•
Optical drive devices: includes any kind of CD-ROM or DVD-ROM drives.
•
Floppy disk drives: 3.5-inch disks only.
To activate Acer eLock Management, a password must be set at first. Once set, you may apply locks to any of the
three kinds of devices. The lock(s) will be set without any reboot necessary, and will remain locked after rebooting,
until unlocked.
If you do not set a password, Acer eLock Management will reset back to the initial status with all locks cancelled.
Note: If you lose the password, there is no method to reset it except by reformatting the notebook or
taking the notebook to an Acer Customer Service Center. Be sure to remember or write down the
password.
Chapter 1
19
Acer ePerformance Management
Acer ePerformance Management is a system optimization tool that boosts the performance of the Acer notebook.
It provides you with the following options to enhance overall system performance:
20
•
Memory optimization: releases unused memory and checks memory usage.
•
Disk optimization: removes unneeded items and files.
•
Speed optimization: improves the usability and performance of the Windows XP system.
Chapter 1
Acer eRecovery Management
Acer eRecovery Management is a powerful utility with the need for recovery disks provided by the manufacturer.
The Acer eRecovery Management utility occupies space in a hidden partition on the system’s HDD. User-created
backups are stored on D:\ drive. Acer eRecovery Management provides:
•
Password protection
•
Recovery of applications and drives
•
Image or data backup:
•
•
Backup to HDD (set recovery point)
•
Backup to CD or DVD
Image or data recovery tools:
•
Recovery from a hidden partition (factory defaults)
•
Recovery from the HDD (most recent user-defined recovery point)
•
Recovery from CD or DVD
Note: If the computer did not come with a Recovery CD or System CD, please use Acer eRecovery
Management’s “System backup to optical disk” feature to burn a backup image to CD or DVD. To ensure the
best results when recovering the system using a CD or Acer eRecovery Management, detach all peripherals
(except external Acer ODD, if equipped), including the Acer ezDock.
Chapter 1
21
Acer eSettings Management
Acer eSettings Management allows you to inspect hardware specification and to monitor the system health status.
Furthermore, Acer eSettings Management enables you to optimize your Windows operating system, so your
computer runs faster, smoother and better.
22
•
Provides a simple graphical user interface for navigating through the program effortlessly.
•
Displays general system status and advanced monitoring for power users.
•
Logs when a hardware component has been removed or replaced.
•
Permits you to migrate personal settings.
•
Keeps a history log of all alerts that were previously issued.
Chapter 1
Acer eNet Management
Acer eNet Management helps you to quickly and easily connect to both wired and wireless networks in a variety of
locations. To access this utility, either click on the “Acer eNet Management” icon on the notebook, or start the
program from the Start menu. You also have the option to set Acer eNet Management to start automatically when
you boot up the PC.
Acer eNet Management automatically detects the best settings for a new location, while offering you the freedom
to manually adjust the settings to match your needs, simply by right clicking on the icon in the task bar.
Acer eNet Management can save network settings for a location to a profile, and automatically apply the
appropriate profile when you move from one location to another. The settings stored include network connection
settings (IP and DNS settings, wireless AP details, etc.), as well as default printer settings. The security and safety
concerns mean that Acer eNet Management does not store username and password information.
Chapter 1
23
24
Chapter 1
Acer ePower Management
Acer ePower Management features a straightforward user interface. To launch it, select Acer ePower
Management from the Empowering Technology interface, or double click the Acer ePower Management icon in the
task tray.
AC mode
The default setting is “Maximum Performance.” You can adjust CPU speed, LCD brightness and other settings, or
click on buttons to turn the following functions on or off: Wireless LAN, Bluetooth, CardBus, Memory Card, Audio,
and Wired LAN.
DC mode
To suit your usage, there are four pre-defined profiles: Entertainment, Presentation, Word Processing, and
Maximum Battery. Or, you can define up to three of your own profiles.
Battery status
For real-time battery life estimates based on current usage, refer to the panel on the lower left side of the window.
You can also click Settings to:
•
Set alarms.
•
Reload factory defaults.
•
Select what actions will be taken when the cover is closed, and set passwords for accessing to the system
after Hibernation or Stand-by.
•
View information about Acer ePower Management.
Chapter 1
25
26
Chapter 1
Acer ePresentation Management
Acer ePresentation Management lets you select from two of the most common projector resolution: XGA and
SVGA.
Chapter 1
27
Acer OrbiCam
The Acer OrbiCam is a 1.3 megapixel CMOS camera appropriately mounted on the top of the LCD panel. The
camera’s 225-degree ergonomic rotation allows you to capture high-resolution photos or videos up front or at the
back of the LCD panel. The Acer OrbiCam fully supports the Acer Video Conference technology so that you can
transmit the best video quality over an instant messenger service.
1
#
23
Item
No.
#
Item
Item
1
Lens
2
Power indicator
3
Rubber grip (selected models only)
Rotating the Acer Orbicam
The Acer OrbiCam rotates 225 degrees counterclockwise to achieve the desired angle. Refer to the illustrations
below:
Note: Do not rotate the camera clockwise to prevent it from the damage.
For your convenience, the camera snaps 45 degrees to match the position of your face in front in back of the LCD
panel.
Launching the Acer OrbiCam (for 1.3 megapixel camera
models only)
To launch the Acer OrbiCam, double click on the Acer OrbiCam icon on the screen or Click Start > All programs
> Acer > Acer OrbiCam. The Acer OrbiCam capture windows window appears as below:
28
Chapter 1
Changing the Acer OrbiCam Settings
Resolution
To change the capture resolution, click the displayed resolution at the bottom right corner of the capture window,
then select the desired resolution.
Note: Setting the camera resolution to 640 x 480 or larger does not change the capture window size.
Options
Click Options to display the Window, Preview, and Folder tabs. Use the options to change the capture window
size, preview settings, and the folder for captured photos or videos.
Chapter 1
29
Options
Window, Preview
Folder
Camera Settings
•
Basic settings: Click the Camera Settings icon on the bottom right corner of the capture display, then
select Camera Settings from the pop-up menu. You can adjust the Video, Audio, and Zoom/Face
tracking options from this window.
Camera Settings
Video, Audio
Video, Audio
•
Camera Settings
Zoom/Face tracking
Zoom/Face tracking
Capture settings: From the Camera Settings window, click the Driver Settings button. The Properties
Driver Settings
window will appear.
Driver Settings
Properties
Properties
Device Settings
Device Settings
•
Device Settings allows you to change the camera brightness, contrast, hue, saturation, sharpness,
etc.
Advanced Settings
•
Advanced Settings allows you to achieve gain control, implement image mirror, select image
enhancements and anti-flicker settings, and turn on/off the camera indicator.
Advanced Settings
Zoom/Face Track Settings
Zoom/Face Track Settings
30
Chapter 1
•
Zoom/Face Track Settings allows you to adjust the zoom level and turn the face tracking feature on
or off.
Capturing Photos or Videos
To capture a photo or a video clip, rotate the Acer OrbiCam to get the desired angle, then click the Take a Picture
or Record a Video button. The Windows Picture and Fax Viewer or the Windows Media Player automatically
launches to display or play a preview of the photo/video clip.
Note: By default, all photos and videos are saved in the My Pictures and My Videos folder.
Using the Acer OrbiCam as Webcam
The Acer OrbiCam is automatically selected as the capture device of any instant messenger (IM) application. To
use the Acer OrbiCam as a webcam, open the IM service, then select the video/webcam feature. You can now
broadcast from your location to an IM partner anywhere in the world.
Enabling the Acer VisageON (for 1.3 megapixel camera models
only)
The Acer VisageON technology comes with two features: Face tracking and Video effects (selected models
only). The Face Tracking feature tracks your head movement and automatically centers your face in the capture
window. The video effects feature allows you to select and apply an effect to your video transmissions.
Note: The face tracking feature is not capable of centering your face beyond the capture window frame.
Minimal head movements are tracked more efficiently.
To Enable Acer VisageON:
1. Right click on this icon, then select VisageON from the pop-up menu.
VisageON
VisageON
The VisageON window appears as below:
2. Select and apply a video effect in the left section of the VisageON window. Change the face tracking settings
and options in the right section.
Chapter 1
31
Single User
Users
Multiple
To Use the Face Tracking Feature
1. Click the left icon down arrow button, then select Single User or Multiple
the pop-up menu. For
SingleUsers
User from
Multiple
Users
multiple users, the face
tracking feature automatically centers all the users’ face in the capture window,
otherwise the utility centers the face of the user closest to the camera.
2. Click the right icon to zoom in/out or reset the current view.
VisageON
3. Click VisageON to display a menu that allows to change the configuration of the camera, face tracking and
video effects settings.
Using video effects
Video Settings
Using Video Effects (selected models only)
The Video Settings section allows you to select an avatar or accessory video effect from
Videothe list. To select an
effect:
Effect Selection
1. Click the encircled icon to display the available video effects. The Video Effect Selection window appears as
below:
2. Click on a video effect to use. The selected effect appears in the video effects section of the VisageON window.
32
Chapter 1
Note: When using avatars, you may have to calibrate the face points to achieve better tracking. Follow screen
instructions in the VisageON to continue.
Note: You may use video effects when using the camera for IM chat/video sessions or call conferences.
Chapter 1
33
Note:
Using the System Utilities
Note: The system utilities work under Microsoft Windows XP only.
Acer GridVista (dual-display compatible)
Note: This feature is only available on certain models.
Start Control Panel Display
To enable the dual monitor feature of the notebook, first ensure that the second monitor is connected, then select
Settings
(2)
Start, Control Panel, Display and click on Settings. Select the secondary monitor (2) icon in the display box and
then click the check boxExtend
Extend my my
windows
desktop onto
this monitor.onto
Finally, this
click Apply
to confirm the new
windows
desktop
monitor
settings and click OK to complete the process.
Apply
OK
Note:
Settings
Apply
Start Control Panel Display
(2)
Extend my windows desktop onto this monitor
OK
Acer GridVista is a handy utility that offers four pre-defined display settings so you can view multiple windows on
the same screen. To access this function, please go to Start > All Programs and click on Acer GridVista. You may
Startsettings
All Programs
choose any one of the four display
indicated below: Acer GridVista
Start All Programs
Acer GridVista
Acer Gridvista is dual-display compatible, allowing two displays to be partitioned independently. Acer GridVista is
simple to set up:
1. Run Acer GridVista and select your preferred screen configuration for each display from the task bar.
2. Drag and drop each window into the appropriate grid.
3. Enjoy the convenience of a well-organized desktop.
34
Chapter 1
Note: Please ensure that the resolution setting of the second monitor is set to the manufacturer's
recommended value.
Note:
Note:
Launch Manager
Launch Manager allows you"Easy-launch
to set the four buttons"
easy-launch
above the keyboard. You can access the
onbuttons
page located
24
Launch Manager by clicking on Start > All Programs > Launch Manager to start the application.
Start All Programs
Launch Manager
"Easy-launch buttons" on page 24
Start All Programs
Launch Manager
Chapter 1
35
Norton AntiVirus
Norton AntiVirus is an anti-virus software that finds and repairs infected files, and protects against viruses to keep
you computer data safe and secure.
How do I check for viruses?
A Full System Scan scans all files on your computer. To perform a system scan:
Norton AntiVirus
1. Start Norton Antivirus: Double click on the Norton AntiVirus Icon on the desktop or click on the Start menu in
Start
Programs
the Windows task bar, highlight Programs, and select Norton Antivirus.
Norton AntiVirus
2. In the Norton Antivirus main window, click Scans.
Scans
Scans
Run Full System Scan
3. In the Scans panel, click Run Full System Scan.
4. When the scan is complete, a scan summary appears. Click Finished.
Finished
You can schedule customized virus scans that tun unattended on specific dates and times or at periodic intervals.
If you are using the computer when the scheduled scan begins, it runs in the background so that you do not have
to stop working.
For more information, please refer to the Norton AntiVirus Help menu.
36
Chapter 1
Hardware Specification and Configuration
Processor
Item
T7600
T7400
T7200
T5600
T5500
CPU speed (GHz)
2.33
2.16
2
1.83
1.66
Bus speed (MHz)
667
667
667
667
667
Bus/Core Ratio
14
13
12
11
10
L2 cache size (MB)
4
4
4
2
2
L2 cache speed (GHz)
2.33
2.16
2
1.83
1.66
Package type (pin)
479/478
479/478
479/478
479/478
479/478
Manufacturing technology (nm)
65
65
65
65
65
Thermal design power
34W
34W
34W
34W
34W
Thermal specification ( C)
100
100
100
100
100
Core voltage (V)
1.0375 ~
1.30
1.0375 ~
1.30
1.0375 ~
1.30
1.0375 ~
1.30
1.0375 ~
1.30
T2700
T2600
T2500
T2400
T2300
o
Item
CPU speed (GHz)
2.33
2.16
2
1.83
1.66
Bus speed (MHz)
667
667
667
667
667
Bus/Core Ratio
13
13
12
11
10
L2 cache size (MB)
2
2
2
2
2
L2 cache speed (GHz)
2.33
2.16
2
1.83
1.66
Package type (pin)
478
478
479/478
478
478
Manufacturing technology (nm)
65
65
65
65
65
Thermal design power
31W
31W
31W
31W
31W
100
100
100
100
100
1.0375 ~
1.30
1.0375 ~
1.30
1.0375 ~
1.30
1.0375 ~
1.30
1.0375 ~
1.30
Thermal specification (
oC)
Core voltage (V)
Main Chips
Item
Specification
System core logic
945GM/945PM/940GML + ICH7M
Super I/O controller
ICH7M LPC interface
Audio controller
Codec ALC883
Video controller
•
•
UMA for 945GM and 940GML
NVIDIA® GeForce® Go 7300
HDD controller
ICH7M
Keyboard controller
ENE KB3910
PCMCIA controller
TI7412 (with card reader and 1394 support)
soDIMM controller
945GM/945PM/940GML
System Memory
Item
Description
Chipset
945GM/945PM/940GML
Feature
•
•
•
•
Chapter 1
DDR2 400/533/667 MHz SDRAM memory interface design
Two DDR SODIMM slots
Maximum memory up to 4GB (with two 2GB SODIMM)
Dual Channel support
37
VGA Interface
Item
UMA
Discrete
Chip
945GM/940GML
Nvidia G72MV
VRAM
up to 128MB
up to 256MB
Card Reader
Item
Description
PCMCIA controller
TI7412
Card type support
Type II
Number of slot
One
Feature
Five-in-one Card Reader: Memory Stick (MS), Memory Stick Pro (MS
PRO), MultiMediaCard (MMC), Secure Digital (SD) and xD-Picture
Card (xD).
Audio Interface
Item
Description
Audio controller
Realtek ALC833 Azadia Codec
Feature
•
•
•
•
•
•
•
•
Built-in
Stereo
SNR > 85, high-performance DACs with 95dB SNR (A-Weighting), ADCs
with 85dB SNR (A-Weighting)
Internal Microphone
Two speakers, at least 1.5W / 30cc for each
2* digital microphone array
VoIP function support
Universal jack function support
LAN Interface
Item
Description
LAN controller
Realtek RTL8111B
Feature
•
•
•
•
Connector type
RJ-45
10/ 100/ 1000 Mbps PCI LAN
Jumbo frame support
WOL from S5 support
File deployment support
Wireless LAN Interface
Item
38
Description
Card type
Mini-PCI
Mode
•
•
•
Support
Wi-Fi, WPA2, WMM, CCX V3/V4
802.11a/b/g
802.11b/g
Built-in two antenna (placed on the top of LCD on the side of LCD latch,
the wire of antenna can not be placed under the panel)
Chapter 1
Modem
Item
Description
Controller
ICH7M
Data modem data baud
rate (bps)
56K
Modem/bluetooth
protocol supported
•
•
•
Connector type
RJ-11
V.90/V.92 AC-Link modem with PTT approval
Wake-on-Ring ready
CISPR22 application
Keyboard
Item
Description
Controller
ENE KB3910
Model name
New Acer Ergo Keyboard
Feature
•
•
•
•
•
•
•
•
•
105 / 106 keys standard keyboard
Touch pad with 4-way integrated scroll button
Windows keys and application keys support
Standard pitch, 2.5 mm travel length
Hotkey controls
Embedded numeric keypad
Multi-language support
Spill-proof
Four easy-launch buttons: Internet browser, E-mail with LED, Acer
Empowering, one user-programmable button
Battery
Item
Specification
Vendor & model name
Panasonic / Sanyo / Sony
Battery Type
Li-Ion
Pack capacity
8-cell: 2400 mAh
6-cell: 2000 mAh
Power Management
Legacy Mode
ACPI Mode
Off
•
•
Mech. Off (G3): All devices in the system are turned off completely.
Soft Off: (G2/S5): All devices in the system are turned off completely by
OS shutdown.
On
•
Working (G0/S0): Individual devices such as the CPU and hard disk may
be power-managed in this state.
S3 Sleeping State: CPU set power down, VGA suspend, PCMCIA
suspend, Audio power down, HDD power down, CD-ROM power down,
Super I/O low power mode.
S4 Sleeping State: It is also called hibernation state. The system saves all
system setting and data onto disk before the whole system is powered
off.
•
•
Chapter 1
39
LCD Panel
Item
Specification
Model name
AUO
B170PW03 V3
B170PW03 V4
QDI
QD17TL02-06
SAMSUNG
LTN170WX-L05-1
LTN170WX-L05-H
LG
LP171WP4-TL02
Screen Diagonal
(mm)
17.1” WXGA
17.1” WXGA
17.1” WXGA
17.1” WXGA
Active Area (mm)
367.20 (W) x
229.50 (H)
367.20 (W) x
229.50(H)
367.20 (W) x
229.50(H)
367.20 (W) x
232.90 (H)
Display resolution
(pixels)
1440 x 3(RGB) x
900
1440 x 3 (RGB) x
900
1440 x 3 (RGB) x
900
1440 x 3 (RGB) x
900
Pixel Pitch (mm)
0.255 x 0.255
0.255 x 0.255
0.255 x 0.255
0.255 x 0.255
Pixel Arrangement
RGB vertical stripe
RGB vertical stripe
RGB vertical stripe
RGB vertical stripe
Display Mode
Normally white
Normally white
Normally white
Normally white
Surface Treatment
non-glare type (V3)
glare type (V4)
Hard coating (3H)
glare type
non-glare type (1)
glare type (H)
glare type
Typical White
200 (Typical)
200 (Typical)
200 (Typical)
200 (Typical)
Contrast Ratio
300 (Typical)
300 (Min)
350 (Typical)
350 (Min)
Response Time
(Optical Rise Time +
Fall Time) msec
16 (Typical)
25 (Typical)
25 (Typical)
35 (Max.)
25 (Typical)
Normal Input Voltage
of Power Supply
+3.3V (Typical)
+3.3V (Typical)
+3.3V (Typical)
+3.3V (Typical)
Power Consumption
(watt)
8 (Max)
4.7 (Typical)
4.320 (typ)
4.78 (Typ)
Weight
700g (Max)
750g
750 (Typical)
670 (Typical)
Physical Size (mm)
382.2 (W) x 244.5
(H) x 6.6 (D)
382.7 (H) x 245.1
(V) x7.0 (T)
382.7 (H) x 245 (V)
x 7.0 (T)
382.2 (W) x 244.5
(H) x 6.5 (D)
Electrical Interface
2 channel LVDS
2 channel LVDS
3.3V LVDS
2 channel LVDS
Support Color
Native 262K colors
Native 262K colors
Native 262K colors
Native 262K colors
Viewing Angle (typ.)
Horizontal: Right/Left
Vertical: Upper/Lower
45/45
20/35
45/45
15/35
65/65
45/55
45/45
15/35
Temperature
0 to 50
-20 to 60
0 to 50
-25 to 60
0 to 50
-20 to 60
0 to 50
-20 to 60
Luminance (cd/m2)
Range(oC)
Operating Storage
(shipping)
40
Chapter 1
AC Adaptor
Item
Specification
Model name
LiteOn PA-1900-04AW
Delta 90W ADP-90SB BBAA
for 100Vac or 240Vac input AC
voltage
for 100Vac or 240Vac input AC
voltage
Input feature
Rated voltage
Input voltage range
from 90Vac to 264Vac
from 90Vac to 265Vac
Rated frequency
for 50Hz or 60Hz
for 50Hz or 60Hz
Frequency range
from 47Hz to 63Hz
from 47Hz to 63Hz
Steady AC current
less than 1.5A rms at 100Vac input
and maximum load
less than 1.5A rms at 100Vac input
and maximum load
Rated voltage
19V
19V
Voltage range
18.05V to 20V
from 18.2V to 19.8V
Rated power
90 W
90 W
Output ripple and noise
less than 300mVp-p
less than 300mVp-p
Turn on delay time
within two seconds at 115 Vac input
voltage
within two seconds at 115 Vac input
voltage
Temperature
Operating: 0 to 40oC
Non-operating: -31 to 60oC
Operating: 0 to 40oC
Non-operating: -31 to 60oC
Output feature
Hard Disk Drive
Seagate
Model
ST9120821A
ST9120824A
ST9100824A
ST9100825A
ST98823A
ST980829A
ST96812A
Formatted
Gbytes (512
bytes/sector)
120
100
80
60
Physical read/
write head
4
4
3
3
Discs
2
2
2
2
Spindle Speed
(RPM)
4200 (ST9120824A, ST9100825A, ST980829A)
5400 (ST9120821A, ST9100824A, ST98823A, ST96812A)
Internal transfer
rate (Mbytes/sec.
max.)
56.25 (ST9120824A, ST9100825A, ST980829A)
48.25 (ST9120821A, ST9100824A, ST98823A, ST96812A)
I/O data transfer
rate (Mbytes/sec.
max.)
100
ATA data transfer
mode supported
PIO modes 0-4; Multiword DMA modes 0-2; Ultra DMA modes 0-5
Bytes per sector
512
Average latency
(msec)
5.6
Average seek,
read (msec.
typical)
12.5
Drive Specification
Chapter 1
41
Seagate
42
Average seek,
write (msec.
typical)
14.5
Cache buffer
8 Mbytes
Interface
Serial ATA
Startup current
(typical, peak)
+5V: 1.1 amps
Ambient
temperature
5 to 55oC (operating), -40 to 70oC (nonoperating)
Temperature
gradient (oC per
hour max.)
20oC (operating), 30oC (nonoperating)
Relative humidity
5% to 90% (operating), 5% to 95% (nonoperating)
Relative humidity
gradient
30% per hour max.
Drive acoustics,
sound power
(bels) idle
2.4 (typical), 2.6 (max)
Shock, operating
(Gs max. at 0.5
msec.)
250
Shock,
nonoperating (Gs
max. at 2 msec.)
800
Vibration,
operating
1.0 G (0 to peak, 5-500 Hz)
Vibration,
nonoperating
5 Gs (0 to peak, 5-500 Hz)
Nonrecoverable
read errors
1 per 1014 bits read, max.
Seek power
(typical)
2.20 watts
Read/write power
(typical)
Read: 1.90 watts; Write: 2.30 watts
Idle mode, lower
power (typical)
0.80 watts
Standby mode
0.28 watts
Sleep mode
0.28 watts
Voltage tolerance
+5.0V +/- 5%
Chapter 1
24X Combo Drive Interface
Item
Model
Specification
PHILIPS SCB5265
LITEON SSC-2485K
Transfer rate (KB/sec.)
Sustained:
• DVD: Max 10.56Mbytes/sec.
• CD: 3600Kbytes/sec.
Sustained:
• DVD: Min 10.15Mbytes/sec.
• CD: 3500 Kbytes/sec.
Access Time (Typical)
•
•
•
•
•
•
•
•
Buffer Memory
2MB
2MB
Interface
Compliant to ATA/ATAPI-5
ATA/ATAPI-6, MMC-3 and SFF8090 Ver5,
Revision 1.2.
Applicable disc format
•
Performance Specification
•
•
Loading mechanism
DVD: Random Access: 125 ms
DVD: Full Stroke: 165ms
CD: Random Access:105ms
CD: Full Stroke:160ms
DVD (read): DVD 5, 9, 10, 18, DVD•
ROM, DVD-Video, DVD-R 3.95G, DVDR 4.7G, DVD-RW, DVD+R, DVD+RW,
Multi-Border DVD-R/DVD-RW, MultiSession DVD+R, DVD+RW, DVD-RAM
CD (write): CD-DA, CD ROM Mode-1,
CD-ROM/XA Mode-2 Form-1 and
Mode-2 Form-2, CD-I, Video-CD
(MPEG-1), CD-Text
CD (write): CD-DA, CD-ROM Mode-1,
CD-ROM/XA Mode-2 Form-1 and
Mode-2, CD-i, Video-CD, CD-Text
Load: Manual load
DVD: Random Access: 100 ms
DVD: Full Stroke: 190ms
CD: Random Access:95ms
CD: Full Stroke:180ms
CD: CD-DA, CD-ROM Mode-1, CDROM XA Mode-2 Form-1 and Form-2,
CD-I Ready, Video-CD(MPEG-1),
Karaoke-CD, PhotoCD (Multi-Session),
Enhance CD, CD extra, I-Trax CD and
UDF
Manual load/DC brushless motor system
Power Requirement
Max. 1300mA
Max. 1200mA
Input Voltage
5 V +/- 5% (Operating)
5 V +/- 5% (Operating)
Chapter 1
43
8X DVD Dual Interface
Item
Vendor and model name
Specification
PHILIPS SDVD8441
Performance specification
Transfer rate (KB/sec.)
Access time (typical)
Sustained:
• DVD:10.9Mbytes/sec. (Typ)
•
CD: 3650Kbytes/sec. (Typ)
•
•
•
•
DVD: Random Access: 130 ms
CD: Random Access:130ms
CD: Full Stroke:240ms
Buffer memory
2MB
Interface
ATA/ATAPI-5
Applicable disc format
•
•
•
•
44
DVD: Full Stroke: 240ms
DVD (read): DVD-ROM 5,9,10,18, DVD-VIDEO, DVD-AUDIO, DVD-R, DVD-R
3.95G, DVD-R MULTI BORDER, DVD-RW, DVD+R, DVD+R DL, DVD+R MULTISESSION, DVD+RW
CD (read): CD-DA, CD-ROM Mode-1, CD-ROM/XA Mode-2 Form-1 Form-2, CD-I,
CD-I Bridge, Video-CD(MPEG-1), Karaoke CD, Photo-CD, Enhanced CD, CD
Plus, CD Extra, i-trax CD, CD-Text, CD-R, and CD-RW
DVD (write): DVD Data & Video
CD (write): CD-DA, CD-ROM Mode-1, CD-ROM/XA Mode-2 Form-1 and Mode-2
Form-2, CD-i, Video-CD, CD-Text
Loading mechanism
Load: manual load
Power consumption
Max. 1500 mA
Input voltage
5V +/- 5% (operating)
Chapter 1
8X Super Multi (DL)
Item
Vendor and model name
Specification
Liteon SSM 8515S
Pioneer DVR-K06RS
Philip SDVD-8821
Transfer rate read (KB/sec.)
Sustained:
• DVD: 10.00Mbytes/
sec.
• CD: 3500kbytes/sec.
Sustained:
• DVD: 10.80Mbytes/
sec.
• CD: 3600kbytes/sec.
Sustained:
• DVD: 10.90Mbytes/
sec.
• CD: 3650kbytes/sec.
Access time / Seek time
•
•
•
Performance Specification
•
•
•
DVD: random access
130ms
DVD: full stroke 250ms
CD: random access
110ms
CD: full stroke 220ms
•
•
Access time: DVD 160
msec; CD 150 msec.
Random seek time:
DVD 150 msec; CD
140 msec.
Full stroke seek time:
DVD 300 msec; CD
290 msec.
•
Random access: DVD
130ms; CD 130ms
Full stroke: DVD
200ms; CD 240ms
Buffer memory
2MB
2MB
2MB
Interface
compliant to ATA/ATAPI-6,
MMC-4 and SFF8090
Ver5
compliant to SFF8020,
SFF8090
compliant to ATA/ATA-5
Applicable disc format
CD-DA, CD-ROM Mode1, CD-ROM/XA Mode-2
Form-1 and Mode-2
Form-2, CD-I, Video-CD
(MPEG-1), CD-Text,
PhotoCD, Enhance CD,
CD extra, I-Trax CD and
UDF DVD-ROM, DVDVideo, DVD-Audio, DVDR single/multi border,
DVD+R single/multi
session, DVD-RW,
DVD+RW, DVD-RAM
KODAK Photo CD single
and multi-session, CD
Extra (CD PLUS), Video
CD, CD text data (read/
write), CD-R (read/write),
DVD-ROM, DVD-R (read/
write), DVD-R DL (read/
write), DVD-RW (read/
write), DVD+RW (read/
write), DVD+R (read/
write), DVD+R DL (read/
write), DVD+RW (read/
write), DVD+RW high
speed (read/write), DVDRAM (read/write)
•
•
DVD read: DVD-5,
DVD-9, DVD-10, DVD18, DVD-Video, DVDAudio, SACD (Hybrid),
DVD-R, DVD-R DL,
DVD-R 3.95GB, DVDR Authoring, DVD-R
multi-border, DVD-RW,
DVD+R, DVD+R DL,
DVD+R Multi-session,
DVD+RW, DVD-RAM
V1.0, DVD-RAM V2.1;
CD read: CD-DA, CDROM Mode-1, CDROM/XA Mode-2
Form-1 and Mode-2
Form-2, CD-i, CD-i
Bridge, Video-CD
(MPEG-1), Karaoke
CD, Photo-CD,
Enhanced CD, CD
Plus, CD Extra, i-trax
CD, CD-Text, CD-R,
CD-RW
DVD write: DVD Data,
DVD-video; CD write:
CD-DA, CD-ROM
Mode-1, CD-ROM/XA
Mode-2 Form-1 and
Mode-2 Form-2, CD-i,
Video-CD, CD-text
Loading mechanism
Load: manual load/DC
brushless motor system
N/A
N/A
Power requirement
Max. 1500mA
Max. 1800mA
Max. 1300mA
Input voltage
+5V +/- 5% (operating)
+5V +/- 5% (operating)
+5V +/- 5% (operating)
Chapter 1
45
Chapter 2
System Utilities
BIOS Setup Utility
The BIOS Setup Utility is a hardware configuration program built in the BIOS (Basic Input / Output System) of
computer. Generally speaking, the computer is already properly configured and optimized, and you do not need to
run this utility.
However, if you encounter configuration problems, you may need to run Setup. Otherwise, you can also refer to
Chapter 4 Troubleshooting when problem arises.
Invoking BIOS Setup
To activate the BIOS Utility, press F2 during POST (when “Press <F2> to enter Setup” message is prompted on
the left-bottom side of the screen).
There are six prime items in the BIOS Setup Utility. They are Information, Main, Advanced, Security, Boot and Exit.
In the coming pages, we will explain the BIOS Setup Utility by item.
Part
Description
Information
Display the system informations.
Main
Allows the user to specify standard IBM PC AT system
parameters.
Security
Provides security setting of the system.
Boot
Allows the user to specify the boot options.
Exit
Allows the user to save CMOS setting and exit Setup.
Note: During setup, all Fn function keys and power saving function are disabled.
Chapter 2
46
Information
47
•
CPU type: This item will show the CPU information of the system.
•
CPU speed: This item will show the COU clock speed.
•
IDE1 model name: This item will show the model name of HDD installed on primary IDE master. The hard
disk model name is automatically detected by the system. If there is no hard disk present or unknown
type, “None” should be shown on this field.
•
IDE1 serial number: This item will show the serial number of HDD installed on Primary IDE master. If no
hard disk or other devices are installed on primary IDE master, it will display a blank line.
•
System BIOS version: This field reports BIOS version of the system.
•
KBC version: This field reports keyboard controller version of the system.
•
Serial Number: This item is the serial number of the system.
•
Asset Tag Number: This item is the asset tag number of the system.
•
UUID: It shows only when an internal LAN device is available.
Chapter 2
Main
•
System Time and System Date: The hours are displayed with 24-hour format. The changes in these two
items take effect immediately.
•
System Memory: This item reports the memory size of system base memory. The size is fixed to 640KB.
•
Extended Memory: It reports the memory size of the extended memory in the system. The extended
memory size is equal to total memory size (one MB).
•
Video Memory: It indicates the video memory size.
•
Quiet Boot:
•
•
Enabled: Customer Logo is displayed, and Summary Screen is disabled.
•
Disabled: Customer Logo is displayed, and Summary Screen is enabled.
Power on Display:
•
Auto: During power on process, the system will detect if any display device is connected on external
video port. If any external display device is connected, the power on display will be only in CRT (or
projector) mode. Otherwise, it will be in LCD mode.
•
Both: Both the integrated LCD and the external video port (for an external CRT or projector) will be
enabled simultaneously.
•
Network Boot: It permits the users to boot from network.
•
F12 Boot Menu:
•
Enabled: When it is enabled, the users can modify device boot priority by pressing <F12> during
POST.
•
Disabled: When it is not enabled, device boot priority will not be adjustable during POST. The boot
device change is only for one-time change. In other words, when the system is rebooted, the boot
Chapter 2
48
device sequence will be the same as the one defined in the BIOS setup (Boot option).
•
49
D2D Recovery: It allows the users to enable or disable the disk-to-disk recovery.
Chapter 2
Security
The system supports three levels of password protection. The password support consists of a Supervisor
Password, User Password, and Hard Disk Password. All the passwords are stored in a non-volatile storage device
(EEPROM).
•
Password Policy: All the passwords will obey the following rules:
•
All the passwords can be set or cleared in BIOS Setup Security screen.
•
The password entry consists of eight alphanumeric characters. At least one character must be
assigned.
•
The valid keys are listed in the table below:
Chapter 2
Symbol Character
Symbol Name
A-Z
letters A to Z (not case sensitive)
0-9
numerical characters
-
dash
=
equal sign
[
left bracket
]
right bracket
.
period
,
comma
;
semi-colon
50
Symbol Character
51
Symbol Name
/
slash
\
back slash
•
The users can not change or remove password during resuming from S4.
•
The max. number of times to retry the password is limited to three.
•
Supervisor Password: Supervisor Password controls the access of the whole BIOS Setup Utility. If the
Supervisor Password is set, the system will pop up the password dialog box to ask for the password when
the users press <F2> for entering BIOS Setup Utility. If the Supervisor Password is set and Password on
boot is enabled, the system will pop up the password dialog box to ask for the password when the system
is powered on or resumes for S4 state. If the users fail three times consecutively in password verification,
the system will be hung up and the users need to manually power off the system.
•
User Password: If the User Password is set, the system will pop up the password dialog box to ask for the
password when the users press <F2> for entering BIOS Setup Utility. If the Supervisor Password is not
set at first, the User Password can not be set. If the Supervisor Password is cleared, the User Password
will be cleared, too. If the User Password is set and Password on boot is enabled, the system will pop up
the password dialog box to ask for the password when the system is powered on or resumes for S4 state.
If the users fail three times consecutively in password verification, the system will be hung up and the
users need to manually power off the system.
•
Set Supervisor Password / User Password:
•
Highlight the item and press “Enter”, a dialog box will be shown to ask the users to enter new
password and confirm new password.
•
If the users want to reset password, a current password will be required to be tapped in at first. If the
current password is correct, the users are permitted to enter new password and confirm new
password for verification. If the verification is OK, the password setting will be complete after the users
press “Enter”.
•
If the password entered does not match the current password, a dialog box will be shown to ask to reenter the password.
•
Set HDD Password: When shown as “Locked”, the hard drive password currently can not be changed or
disabled. To change or disable it, turn off the system and enter Setup immediately after turning it back on.
Press “Enter” to input change, or disable hard drive password.
•
Password on Boot: It allows the user to specify whether or not a password is required to boot.
Chapter 2
Boot
This menu allows the users to decide the order of bootable devices to load the operating system. It identifies all the
bootable devices in the system and attempts to boot them in the order specified. Bootable devices include the
diskette drive in module bay, the hard disk and the CD-ROM/DVD drive in module bay and onboard LAN device.
Chapter 2
52
Exit
53
•
Exit Saving Changes: It allows the users to save changes to CMOS and reboot the system.
•
Exit Discarding Changes: The users can exit the Setup not to save changes.
•
Load Setup Defaults: It allows the users to load default values in CMOS Setup.
•
Discard Changes: The users can discard previous changes in CMOS Setup.
•
Save Changes: The users can save current changes in CMOS Setup.
Chapter 2
Chapter 3
Machine Disassembly and Replacement
This chapter contains step-by-step procedures on how to disassemble the notebook for maintenance and
troubleshooting.
To disassemble the computer, you need the tools below:
•
Wrist ground strap and conductive mat for preventing electrostatic discharge
•
Small Philips screw driver
•
Flat head screw driver
•
Hexagonal driver
•
Tweezers
Note: The screws for the different components vary in size. During the disassembly process, group the
screws with the corresponding components to avoid mismatch when putting back the components. When you
remove the stripe cover, please be careful not to scrape the cover.
Chapter 3
54
General Information
Before You Begin
Before proceeding with the disassembly procedure, you have to make sure that:
1. The system and all peripherals are powered off.
2. The AC adaptor and all power and signal cables from the system are unplugged.
3. The battery pack is removed.
Note: There are several types of screws used to secure the main unit. The screws vary in length. Please refer
to the screws table after the flowchart. Group the same type of screws together during service disassembling.
Please also remember the screw location for each screw type. If you fasten the screws on the wrong location,
the long screws may cause irrecoverable damage to the main board.
55
Chapter 3
Disassembly Procedure Flowchart
The flowchart gives you a graphic representation on the entire disassembly and reassembly and instructs you how
to remove the components.
No.
Description
Part No.
a
SCW HEX NYL I#R-40/O#4-40 L5.5
34.00015.081
b
SCREW MACH WAFER M2*L4 NI
86.T39V1.002
c
SCRW M2.5*6 ~ L-CASE + U-CASE
86.00D28.330
d
SCRW M2*L3
86.00D29.620
e
SCRW M2.5*5 WAFER B-ZN ROHS
86.00D47.630
f
SCREW M2*L3 NYLOK CR 3+
86.00E25.723
g
SCREW M2*L3 NON-NYLOK CR3+
86.00E31.723
h
SCREW M2.5*L6 NYLOK CR3+
86.00E33.736
Chapter 3
56
No.
57
Description
Part No.
i
SCREW M2.5*L8 NYLOK CR3+
86.00E34.738
j
SCREW M2*L8 NI NON-NYLOK
86.00E35.228
k
SCREW M3x4(86.9A524.4R0)
86.9A524.4R0
l
SCRW M2*4 WAFER NI
86.9A552.4R0
m
SCREW NI M2*6L
86.9A552.6R0
n
SCRW M2.5*L3(NON NYLOK)
86.9A523.3R0
Chapter 3
Disassembly Procedure
Removing the Battery Pack
1. Unlock the battery pack.
2. Slide the battery latch, hold it then remove the battery.
Removing the HDD Module
1. Release the three screws fastening the HDD module cover.
2. Detach the HDD module cover.
3. Release the two screws holding the HDD module then pull the HDD module as arrow indicates and remove the
HDD module.
Chapter 3
58
Removing the MiniPCI Card and the Memory
1. Release the two screws securing the miniPCI cover.
2. Remove the miniPCI cover.
3. Disconnect the wireless antenna then remove the wireless LAN card.
4. Release the two screws securing the RAM cover and remove the RAM cover.
5. Press the left and right latches to pop up the memory.
Removing the Keyboard
1. Open the notebook as shown.
2. Remove the middle cover.
3. There are four latches securing the keyboard.
4. Push those latches by the screw driver as shown and the keyboard will pop up a little.
59
Chapter 3
5. Remove the keyboard and reverse it.
6. Carefully pull the keyboard FFC lock, then disconnect the keyboard FFC.
Chapter 3
60
Separating the LCD Module and Main Unit
1. Pull carefully and disconnect the LCD cable.
2. Tear off the tape securing the wireless antenna and pull out the wireless antenna.
3. Release the two screws securing the LCD hinges on the bottom side.
4. Release the two screws fastening the LCD hinges on the rear side.
5. Release the two screws holding the LCD hinges as shown.
6. Then separate the LCD module from the main unit.
61
Chapter 3
Disassembling the Main Unit
Separating the Upper Case and the Lower Case
1. Release the connector lock and disconnect the touch pad FFC.
2. Release the connector lock and disconnect the function keyboard FFC.
3. Release the three screws securing the upper case.
4. Release the 27 screws holding the lower case.
5. Lift the upper case carefully and disconnect the lid switch cable.
6. Then separate the upper and the lower case.
Chapter 3
62
Removing the Function Keyboard
1. Release the FFC lock and disconnect the function keyboard FFC.
2. Release the four screws holding the function keyboard bracket.
3. Then remove the function keyboard bracket.
4. Carefully disconnect the microphone cable and remove the function keyboard.
63
Chapter 3
Removing the Touch Pad Board
1. Carefully release the FFC lock and disconnect the touch pad board FFC.
2. There are 13 latches holding the touch pad bracket.
3. Unlock those latches with a screw driver as shown then detach the touch pad bracket.
4. Detach the touch pad board.
Chapter 3
64
Removing the ODD Module and Dummy Card
1. Slightly pull the ODD module and remove it.
2. Pull the dummy card from the slot and remove it.
Removing the Main Board
1. Disconnect the fan cable.
2. Disconnect the speaker cable and Bluetooth module cable.
3. Remove the four screws securing the main board.
4. Then detach the main board from the lower case.
65
Chapter 3
Removing the System Fan
1. Release the two screws holding the heatsink.
2. Remove the heatsink.
Removing the Bluetooth Module
1. Detach the bluetooth module from the lower case.
2. Carefully disconnect the bluetooth module cable.
Removing the Speakers
1. Release the four screws securing the left and right speakers.
2. Remove the speakers from the lower case.
Chapter 3
66
Removing the MDC Module
1. Carefully disconnect the MDC cable.
2. Release the two screws securing the MDC board then detach the MDC board.
3. Disconnect the MDC board cable.
Remove the Heatsink Module
1. Release the five screws securing the heatsink.
2. Remove the heatsink module.
67
Chapter 3
Removing the CPU
1. Release the screw counter clockwise with a flat screw driver.
2. Detach the CPU from the CPU socket.
LCD Disassembly
1. Remove the eight rubber caps on the LCD bezel and release the eight screws securing the LCD bezel.
2. Detach the LCD bezel from the LCD module as shown.
3. Release the screw holding the inverter board.
4. Disconnect the inverter board cables as shown and remove the inverter board.
Chapter 3
68
5. Release the four screws securing the LCD panel.
6. Detach the LCD panel carefully and reverse it as shown.
7. Tear off the tapes holding the LCD panel cable carefully then disconnect the LCD panel.
8. Remove the antenna from the LCD cover.
69
Chapter 3
9. Release the four screws securing the left LCD bracket then remove the left LCD bracket.
10. Repeat the anterior step to remove the right LCD bracket.
Chapter 3
70
11. Release the screw holding the CCD module and carefully pull the CCD module cable and LCD cable through
the latch bar and LCD cover.
12. Remove the CCD module cap.
13. Remove the CCD module ring.
14. Push the CCD module upper case a little bit.
15. Then Separate the lower case from the upper case.
16. Release the two screws holding the CCD module board the detach the CCD module board.
71
Chapter 3
Chapter 4
Troubleshooting
Please use the following procedures as a guide for computer problems.
Note: The diagnostic tests are intended to test only Acer products. Non-Acer products, prototype cards, or
modified options may occur errors or invalid responses.
1. Obtain the detailed fail symptoms as many as possible.
2. Verify the symptoms by attempting to recreate, running the diagnostic tests or repeating the same operation.
3. Disassemble and assemble the unit without any power sources.
4. If any problem occurs, you can perform visual inspection before you fellow this chapter’s instructions. You can
check the following:
•
Power cords are properly connected and secured;
•
There are no obvious shorts or opens;
•
There are no obviously burned or heated components;
•
All components appear normal.
Chapter 4
72
System Check Procedures
External Diskette Drive Check
Do the following procedures to isolate the possible effects from a controller, driver, or diskette. A writable,
diagnostic diskette is required.
Note: Make sure that the diskette does not have more than one label attached. Multiple labels may cause
damage to the drive or make the drive fail.
1. Boot from the diagnostic diskette and start the diagnostic programs.
2. See if FDD test is passed as the programs run the FDD test.
3. Follow the instructions in the message window.
If errors occur with the internal diskette driver, reconnect the diskette connector on the system board. If the errors
still remain:
1. Reconnect the external diskette drive.
2. Replace the external diskette driver.
3. Replace the main board.
External CD-ROM Drive Check
Do the following procedures to isolate the possible effects from a controller, driver, or CD-ROM.
Note: Make sure that the CD-ROM does not have any label attached. The label may cause damage to the
drive or make the drive fail.
1. Boot from the diagnostic diskette and start the diagnostic programs.
2. See if CD-ROM test is passed when the programs run the CD-ROM test.
3. Follow the instructions in the message window.
If errors occur, reconnect the connector on the system board. If the errors still remain:
1. Reconnect the external CD-ROM drive.
2. Replace the external CD-ROM drive.
3. Replace the main board.
Keyboard or Auxiliary Input Device Check
Remove the external keyboard if the internal keyboard is under test. If the internal keyboard does not work or an
unexpected error appears, make sure that the flexible cable extending from the internal keyboard is correctly
connected on the system board. If the keyboard is correctly connected, run the Keyboard test.
If errors occur, do the following procedures in sequence to correct the problems. Do not replace a non-defective
FRU.
1. Reconnect the keyboard cable.
2. Replace the keyboard.
3. Replace the main board.
The following auxiliary input devices are supported by this computer.
T
Numeric keypad
T
External keyboard
If any of these devices do not function, reconnect the cable and repeat the anterior procedures.
Memory Check
Follow the procedures below to correct the memory errors.
1. Boot from the diagnostic diskette and start the diagnostic programs.
73
Chapter 4
2. Go to the diagnostic memory in the test items.
3. Press F2 in the test items.
4. Follow the instructions in the message window.
Note: Make sure that the DIMM is correctly inserted into the connector. A wrong connection will cause errors.
Power System Check
To verify the symptoms, power on the computer by using the following power sources separately.
1. Remove the battery pack.
2. Connect the power adaptor and check the power supply.
3. Disconnect the power adaptor and install the battery pack, then check the power supply.
If you think there is a power supply problem, please go to “Check the Power Adaptor” and “Check the Battery
Pack” in this chapter.
Check the Power Adaptor
Unplug the power adaptor cable from the computer and measure the output voltage at the plug of the power
adaptor cable. See the illustration and follow the procedures below.
pin 1: +19V to +20.5V
pin 2: 0V, ground
1. If the voltage is not correct, replace the power adaptor.
2. If the voltage is within the range:
(1) Replace the system board.
(2) If the problem is still not resolved, see “Undetermined Problems”.
(3) If the voltage is not correct, go to the next step.
Note: An audible noise from the power adaptor does not always indicate a defect.
3. If the power-on indicator does not light up, check the power cord of the power adaptor for continuity and correct
installation.
4. If the operational charge does not work, see “Check the Battery Pack”.
Check the Battery Pack
Follow the procedures below to check the battery pack.
From software, this helps to identify the problem is on recharging or discharging.
1. Check the Power Management in Control Panel.
2. Then confirm that the parameters shown in the screen for Current Power Source and Total Battery Power
Remaining are correct.
3. Repeat the step 1 and step 2 for both battery and adaptor.
From hardware, this helps to identify whether you should replace the battery pack or not.
1. Power off the system.
2. Remove the battery pack and measure the voltage between terminals one (+) and seven (-). There are seven
terminals totally. See the illustration below.
3. If the voltage is still less than 7.5V after recharging, replace the battery.
If the battery status indicator does not light up, remove the battery pack. After the battery pack returns to room
temperature, reinstall it to the system.
Chapter 4
74
If the charge indicator does not light up, replace the battery pack. If the charge indicator still does not light up,
replace the AC/DC charger board.
Touchpad Check
If the touchpad does not work, follow the procedures one at a time to correct the problem. Do not replace a nondefective FRU.
1. After rebooting, run Tracking Pad PS2 Mode Driver. For example, run Syn touch driver.
2. Run utility with the PS/2 mouse function and check if the mouse is working.
3. If the PS/2 mouse does not work, then click if the main board to switch board FPC is connected properly.
4. If the main board to switch board FPC is connected correctly, then check if the FFC on the touch pad PCB is
connected properly.
5. If the FFC on the touch pad PCB is connected correctly, check if LS851 JP1 Pin6 = 5V are pules. If yes, then
replace switch board. If not, then go to the next step.
6. Replace the touch pad PCB.
7. If the touch pad still does not work, then replace the FPC on Track Pad PCB.
After you use the touchpad, the pointer drifts on the screen for a short time. This self-acting pointer movement will
occur when a slight, steady pressure is applied to the touchpad pointer. This symptom is not a hardware problem.
No actions are necessary to be taken if the pointer movement stops in a short period of time.
75
Chapter 4
Power-On Self-Test (POST) Error Message
The POST error message index lists the error message and their possible causes.
Note: Perform the FRU replacement or actions in the sequence shown in Error Message List, if the FRU
replacement does not solve the problem, put the original part back in the computer. Do not replace a nondefective FRU.
The error messages are listed in the coming pages to indicate the BIOS signals on the screen and the error
symptoms classified by functions. If the symptom is not included on the list, please refer to “Undetermined
Problems”.
Note: Most of the error messages occur during POST. Some of them show information about a hardware
device, for example, the size of memory installed. Others may indicate problems with a device, such as the
way it has been configured.
Note: If the system fails after you make changes in the BIOS Setup Utility menus, please reset the computer.
Enter Setup and install Setup defaults to correct the errors.
Chapter 4
76
Index of Error Messages
Error Message List
Error Messages
77
FRU/Action in Sequence
Struck Key
See “Keyboard or Auxiliary Input Device Check“.
System CMOS checksum bad Default configuration used
RTC battery
Run BIOS Setup Utility to reconfigure system, then
reboot system.
Real time clock error
RTC battery
Run BIOS Setup Utility to reconfigure system time, then
reboot system.
Main board
Previous boot incomplete - Default
configuration used
“Load Default Settings” in BIOS Setup Utility.
RTC battery
Main board
Invalid System Configuration Data
“Load Default Settings” in BIOS Setup Utility.
Main board
Operating system not found
Enter Setup and see if fixed disk and drive A are
properly identified.
Diskette drive
Hard disk drive
Main board
Power-on indicator turns off and LCD
is blank.
Power source (battery pack and power adapter.) See
“Power System Check“.
Ensure every connector is connected tightly and
correctly.
Reconnect the DIMM.
Main board.
Power-on indicator turns on and LCD
is blank.
Power source (battery pack and power adapter.) See
“Power System Check“.
Reconnect the LCD connector
Hard disk drive
LCD cable
LCD inverter
LCD
Main board
Power-on indicator turns on and LCD
is blank. But you can see POST on an
external CRT.
Reconnect the LCD connectors.
LCD cable
LCD inverter
LCD
Main board
Power-on indicator turns on and a
blinking cursor shown on LCD during
POST.
Ensure every connector is connected tightly and
correctly.
Main board
Chapter 4
Phoenix BIOS Beep Codes
Code
Beeps
POST Routine Description
02h
Verify Real Mode
03h
Disable Non-Maskable Interrupt (NMI)
04h
Get CPU type
06h
Initialize system hardware
07h
Disable shadow and execute code from
the ROM.
08h
Initialize chipset with initial POST
values
09h
Set IN POST flag
0Ah
Initialize CPU registers
0Bh
Enable CPU cache
0Ch
Initialize caches to initial POST values
0Eh
Initialize I/O component
0Fh
Initialize the local bus IDE
10h
Initialize Power Management
11h
Load alternate registers with initial
POST values
12h
Restore CPU control word during warm
boot
13h
Initialize PCI Bus Mastering devices
14h
Initialize keyboard controller
16h
1-2-2-3
BIOS ROM checksum
17h
Initialize cache before memory autosize
18h
8254 timer initialization
1Ah
8237 DMA controller initialization
1Ch
Reset Programmable Interrupt
Controller
20h
1-3-1-1
Test DRAM refresh
22h
1-3-1-3
Test 8742 Keyboard Controller
24h
Set ES segment register to 4 GB
28h
Autosize DRAM
29h
Initialize POST Memory Manager
2Ah
Clear 215 KB base RAM
2Ch
1-3-4-1
RAM failure on address line xxxx
2Eh
1-3-4-3
RAM failure on data bits xxxx of low
byte of memory bus
2Fh
Enable cache before system BIOS
shadow
32h
Test CPU bus-clock frequency
33h
Initialize Phoenix Dispatch Manager
36h
Warm start shut down
38h
Shadow system BIOS ROM
Chapter 4
78
Code
Beeps
3Ah
Autosize cache
3Ch
Advanced configuration of chipset
registers
3Dh
Load alternate registers with CMOS
values
41h
Initialize extended memory for
RomPilot.
42h
Initialize interrupt vectors
45h
46h
POST device initialization
2-1-2-3
Check ROM copyright notice
47h
Initialize I20 support
48h
Check video configuration against
CMOS
49h
Initialize PCI bus and devices
4Ah
Initialize all video adapters in system
4Bh
QuietBoot start (optional)
4Ch
Shadow video BIOS ROM
4Eh
Display BIOS copyright notice
50h
Display CPU type and speed
51h
Initialize EISA board
52h
Test keyboard
54h
Set key click if enabled
55h
Enable USB devices
58h
79
POST Routine Description
2-2-3-1
Test for unexpected interrupts
59h
Initialize POST display service
5Ah
Display prompt “Press F2 to enter
SETUP”
5Bh
Disable CPU cache
5Ch
Test RAM between 512 and 640 KB
60h
Test extended memory
62h
Test extended memory address lines
64h
Jump to User Patch1
66h
Configure advanced cache registers
67h
Initialize Multi Processor APIC
68h
Enable external and CPU caches
69h
Setup System Management Mode
(SMM) area
6Ah
Display external L2 cache size
6Bh
Load custom defaults (optional)
6Ch
Display shadow-area message
6Eh
Display possible high address for UMB
recovery
70h
Display error messages
72h
Check for configuration errors
76h
Check for keyboard errors
Chapter 4
Code
Beeps
POST Routine Description
7Ch
Set up hardware interrupt vectors
7Eh
Initialize coprocessor if present
80h
Disable onboard Super I/O ports and
IRQs
81h
Late POST device initialization
82h
Detect and install external RS232 ports
83h
Configure non-MCD IDE controllers
84h
Detect and install external parallel ports
85h
Initialize PC-compatible PnP ISA
devices
86h
Re-initialize onboard I/O ports
87h
Configure Motherboard Configurable
Devices (optional)
88h
Initialize BIOS Data Area
89h
Enable Non-Maskable Interrupts (NMIs)
8Ah
Initialize Extended BIOS Data Area
8Bh
Test and initialize PS/2 mouse
8Ch
Initialize floppy controller
8Fh
Determine number of ATA drives
(optional)
90h
Initialize hard-disk controllers
91h
Initialize local-bus hard-disk controllers
92h
Jump to UserPatch2
93h
Build MPTABLE for multi-processor
boards
95h
Install CD ROM for boot
96h
Clear huge ES segment register
97h
Fixup Multi Processor table
98h
1-2
Search for option ROMs. One long, two
short beeps on checksum failure.
99h
Check for SMART drive (optional)
9Ah
Shadow option ROMs
9Ch
Set up Power Management
9Dh
Initialize security engine (optional)
9Eh
Enable hardware interrupts
9Fh
Determine number of ATA and SCSI
drives
A0h
Set time of day
A2h
Check key lock
A4h
Initialize Typematic rate
A8h
Erase F2 prompt
AAh
Scan for F2 key stroke
ACh
Enter SETUP
AEh
Clear Boot flag
B0h
Check for errors
Chapter 4
80
Code
Beeps
POST Routine Description
B1h
Inform RomPilot about the end of
POST.
B2h
POST done- prepare to boot operating
system
B4h
1
One short beep before boot
B5h
Terminate QuietBoot (optional)
B6h
Check password (optional)
B7h
Initialize ACPI BIOS
B9h
Prepare Boot
BAh
Initialize SMBIOS
BBh
Initialize PnP Option ROMs
BCh
Clear parity checkers
BDh
Display MultiBoot menu
BEh
Clear screen (optional)
BFh
Check virus and backup reminders
C0h
Try to boot with INT 19
C1h
Initialize POST Error Manager (PEM)
C2h
Initialize error logging
C3h
Initialize error display function
C4h
Initialize system error handler
C5h
PnPnd dual CMOS (optional)
C6h
Initialize notebook docking (optional)
C7h
Initialize notebook docking late
C8h
Force check (optional)
C9h
Extended checksum (optional)
CAh
Redirect Int 15h to enable remote
keyboard
CBh
Redirect Int 13h to Memory
Technologies Devices such as ROM,
RAM, PCMCIA, and serial disk.
CCh
Redirect Int 10h to enable remote serial
video
CDh
Re-map I/O and memory for PCMCIA
CEh
Initialize digitizer and display message.
D2h
Unknown interrupt
The following are for boot block in Flash ROM
81
E0h
Initialize the chipset
E1h
Initialize the bridge
E2h
Initialize the CPU
E3h
Initialize the system timer
E4h
Initialize system I/O
E5h
Check force recovery boot
E6h
Checksum BIOS ROM
E7h
Go to BIOS
E8h
Set Huge Segment
Chapter 4
Code
Beeps
POST Routine Description
E9h
Initialize Multi Processor
EAh
Initialize OEM special code
EBh
Initialize PIC and DMA
ECh
Initialize Memory type
EDh
Initialize Memory size
EEh
Shadow Boot Block
EFh
System memory test
F0h
Initialize interrupt vectors
F1h
Initialize Run Time Clock
F2h
Initialize video
F3h
Initialize System Management Mode
F4h
1
Output one beep
F5h
Clear Huge Segment
F6h
Boot to Mini DOS
F7h
Boot to Full DOS
Chapter 4
82
Index of Symptom-to-FRU Error Message
Symptom/Error
Action in Sequence
LCD backlight doesn't work.
LCD is too dark.
LCD brightness cannot be adjusted.
LCD contrast cannot be adjusted.
Enter BIOS Utility to execute “Load Setup Default
Settings”, then reboot system.
Reconnect the LCD connectors.
Keyboard (if contrast and brightness function key do
not work).
LCD inverter ID
LCD cable
LCD inverter
LCD
System board
Unreadable LCD screen
Missing pels in characters
Abnormal screen
Wrong color displayed
Reconnect the LCD connector.
LCD inverter ID
LCD cable
LCD inverter
LCD
System board
LCD has extra horizontal or vertical
lines displayed.
LCD inverter ID
LCD inverter
LCD cable
LCD
System board
Symptom/Error
Indicator incorrectly
remains off or on, but
system runs correctly.
Symptom/Error
83
Action in Sequence
Reconnect the inverter board
Inverter board
System board
Action in Sequence
Power shuts down during
operation.
Power source (battery pack and power adapter). See “Power
System Check”.
Battery pack
Power adapter
Hard drive & battery connection board
System board
The system doesn’t power
on.
Power source (battery pack and power adapter). See “Power
System Check”.
Battery pack
Power adapter
Hard drive & battery connection board
System board
The system doesn’t
power-off.
Power source (battery pack and power adapter). See Power
System Check”.
Hold and press the power switch for more than 4 seconds.
System board
Battery can’t be charged.
See “Check the Battery Pack”.
Battery pack
System board
Chapter 4
Symptom/Error
Action in Sequence
System cannot detect the
PC Card (PCMCIA).
PCMCIA slot assembly
System board
PCMCIA slot pin is
damaged.
PCMCIA slot assembly
Symptom / Error
Memory count (size)
appears different from
actual size.
Action in Sequence
Enter BIOS Setup Utility to execute “Load Default Settings,
then reboot system.
DIMM
System board
Symptom/Error
Action in Sequence
In Windows, multimedia
programs, no sound
comes from the computer.
Audio driver
Speaker
System board
Internal speakers make
noise or emit no sound.
Speaker
System board
Symptom/Error
Action in Sequence
The system will not enter
hibernation.
Keyboard (if control is from the keyboard)
Hard disk drive
System board
The system does not
enter hibernation mode
and four short beeps
every minute.
Press Fn + F4 and see if the computer enters hibernation
mode.
Touchpad
Keyboard
Hard disk connection board
Hard disk drive
System board
The system does not
enter standby mode after
closing the LCD.
LCD cover switch
System board
The system does not
resume from hibernation
mode.
Hard disk connection board
Hard disk drive
System board
The system does not
resume from standby
mode after opening the
LCD.
LCD cover switch
System board
Battery fuel gauge in
Windows does not go
higher than 90%.
Remove battery pack and let it cool for two hours.
Refresh battery (continue to use battery until power off, then
charge battery).
Battery pack
System board
System hangs
intermittently.
Reconnect hard disk/CD-ROM drives.
Hard disk connection board
System board
Chapter 4
84
Symptom/Error
Action in Sequence
System configuration
does not match the
installed devices.
Enter BIOS Setup Utility to execute “Load Default Settings”,
then reboot system.
Reconnect hard disk/CD-ROM/diskette drives.
External display does not
work correctly.
Press Fn + F5, LCD/CRT/Both display switching
System board
USB does not work
correctly.
System board
Print problems
Ensure the “Parallel Port” in the “Onboard Devices
Configuration” of BIOS Setup Utility is set to Enabled.
Onboard Devices Configuration
Run printer self-test.
Printer driver
Printer cable
Printer
System Board
Serial or parallel port
device problems.
Ensure the “Serial Port” in the Devices Configuration” of BIOS
Setup Utility is set to Enabled.
Device driver
Device cable
Device
System board
Symptom/Error
Action in Sequence
Keyboard (one or more
keys) does not work.
Reconnect the keyboard cable.
Keyboard
System board
Touchpad does not work.
Reconnect touchpad cable.
Touchpad board
System board
Symptom/Error
Internal modem does not
work correctly.
Action in Sequence
Modem phone port
modem combo board
System board
Note: If you can not correct the problems according to the anterior tables, see “Undetermined Problems”.
85
Chapter 4
Intermittent Problems
Intermittent system hang problems can be caused by a variety of reasons that have nothing to do with a hardware
defect, such as cosmic radiation, electrostatic discharge, or software errors. FRU replacement should be
considered only when a recurring problem exists.
When analyzing an intermittent problems, follow the procedures below:
1. Run the advanced diagnostic test for the system board in loop mode at least 10 times.
2. If no error is detected, do not replace any FRU.
3. If any error is detected, replace the FRU. Rerun the test to verify that there are no more errors.
Chapter 4
86
Undetermined Problems
The diagnostic problems does not identify which devices fail, which devices are incorrectly installed, whether a
short circuit happens, or whether the system is inoperative.
Note: Verify if all devices attached are supported by the computer.
Note: Verify if the power supply used at the time of failure is operating correctly. You can refer to “Power
System Check”.
Follow the procedures below to isolate the failing FRU. Do not isolate non-defective FRU.
1. Power off the computer.
2. Visually check the devices. If any problems are found, replace the FRU.
3. Remove or disconnect all of the following devices:
•
Non-Acer devices
•
Printer, mouse, and other external devices
•
Battery Pack
•
Hard disk drive
•
DIMM
•
CD-ROM / Diskette drive module
•
PC cards
4. Power on the computer.
5. Determine if the problem has been resolved.
6. If the problem does not recur, reconnect the removed devices one at a time until you find the failed FRU.
7. If the problem remains, replace the following FRU one at a time. Do not replace a non-defective FRU.
87
•
System board
•
LCD assembly
Chapter 4
Chapter 5
Jumper and Connector Location
Top View
No.
Chapter 5
Description
No.
Description
1
DC-in jack
2
USB connector
3
CRT connector
4
RJ11 & RJ45 connector
5
MDC module connector
6
MDC board connector
7
Main battery connector
8
ODD connector
9
Mini PCI slot
10
CPU
11
North bridge
12
DIMM slot
13
South bridge
14
HDD connector
15
Line-in jack
16
Microphone-in jack
88
No.
89
Description
No.
Description
17
Line-out jack
18
Cardbus controller
19
USB connector
20
LAN controller
21
BIOS ROM
22
RTC battery connector
23
5-in-1 card reader
Chapter 5
Bottom View
Item
Chapter 5
Description
Item
Description
1
Keyboard controller
2
Keyboard connector
3
Lid switch connector
4
System fan connector
5
PCMCIA card reader
6
Function key board connector
7
Touch pad board connector
8
Speaker connector
9
Bluetooth module connector
10
LCD cable connector
90
Chapter 6
FRU (Field Replaceable Unit) List
This chapter offers the FRU (Field Replaceable Unit) list in global configuration of Aspire 9420/ 9410/ 7110 and
TravelMate 5620/ 5610/ 5110. Refer to this chapter whenever ordering the parts to repair or for RMA (Return
Merchandise Authorization).
Please note that when ordering FRU parts, you should check the most up-to-date information available on your
regional web or channel. For whatever reasons a part number is changed, it will NOT be noted on the printed
service guide. For Acer authorized service providers, your Acer office may have a different part number code from
those given in the FRU list of this printed service guide. You MUST use the local FRU list provided by your regional
Acer office to order FRU parts for service.
Note: To scrap or to return the defective parts, you should follow the local government ordinance or
regulations on how to dispose them properly, or follow the rules set by your regional Acer office on how to
return it.
Chapter 6
91
Exploded Diagram
92
Chapter 6
Parts
Aspire 9410 UMA
CATEGORY
PART NAME
DESCRIPTION
ACER PART
NO.
ADAPTER
N/A
ADAPTER 90W LITEON PA1900-04WR
ADT 90W LITEON PA1900-04WR
AP.09003.005
ADAPTER 90W DELTA ADP90SB BBAAF
ADT 90W DELTA ADP90SB BBAAF
AP.09001.004
RTC BATTERY
BTY RTC MITSUBISHI
ROHS
23.TCBV1.003
BATTERY PACK LI+ 8CELL
2.4MAH SANYO
BTY PACK LI+ 8C
2.4AH SANYO
BT.00803.018
BATTERY PACK LI+ 8CELL
2.4MAH SONY
BTY PACK LI+ 8C
2.4AH SONY
BT.00807.010
BATTERY PACK LI+ 6CELL
2.0MAH SONY
BTY PACK LI+ 6C
2.0AH SONY
BT.00604.010
BATTERY PACK LI-MN
6CELL 2.0MAH SANYO
BTY PACK LI-MN 6C
2.0AH SANYO
BT.00603.021
BATTERY PACK LI-MN
6CELL 2.0MAH PANASONIC
BTY PACK LI-MN 6C
2.0AH PANA
BT.00605.005
BLUETOOTH MODULE
FOXCONN BCM2045 V01
BT MODULE
FOXCONN BCM2045
V01
54.TB2V1.001
TOUCHPAD BOARD
SYNPATICTM61PUF1G372
TOUCHPAD
SYNPATICTM61PUF1
G372
56.A46V1.001
LED BOARD
MYALL LED BOARD
05569-2 (DIP)
55.TCBV1.001
"INVERTER BOARD 17""
FOXCONN T62I240.00
ROHS"
INVERTER 17''
VK.21189.402
19.TCBV1.001
"INVERTER BOARD 17""
YEC YNV-W02"
"INVERTER 17"" YEC
YNV-W02"
19.TB2V1.001
"INVERTER BOARD 17"" O2
V189-601"
"INVERTER 17"" O2
V189-601"
19.ADFV1.001
BATTERY
N/A
BOARD
Chapter 6
93
CATEGORY
PART NAME
DESCRIPTION
ACER PART
NO.
WIRELESS LAN BOARD
802.11ABG INTEL 3945 RW
WLAN 802.11ABG
INTEL 3945 RW
KI.GLN01.003
WIRELESS LAN BOARD
802.11ABG INTEL 3945 MW2
WLAN 802.11ABG
INTEL 3945 MW2
KI.GLN01.002
WIRELESS LAN BOARD
802.11ABG INTEL 3945 MW1
WLAN 802.11ABG
INTEL 3945 MW1
KI.GLN01.001
WIRELESS LAN BOARD
802.11BG FOXCONN
BCM4318 MURA
WLAN 802.11BG FOX
BCM4318 MURA
54.A74V1.002
MODEM BOARD FOXCONN
T60M893.03
MODEM MDC1.5
FOXCONNT60M893.0
3
54.TCBV1.001
TV TUNER BOARD
TV TUNER MINIPCI
M103 HYBRID
54.ADFV1.001
TV TUNER BOARD
TV TUNER MINIPCI
M104 H/W ENCO
54.ADFV1.002
BLUETOOTH CABLE
B/T CABLE HT MYALL
50.TCBV1.001
TOUCHPAD CABLE
T/P FFC CABLE
MYALL
50.TCBV1.002
LAUNCH BOARD CABLE
LAUNCH BOARD FFC
CABLE MYALL
50.TCBV1.003
N/A
COVER SWITCH CABLE
COVER SWITCH HT
MYALL
50.TCBV1.004
N/A
"LCD CABLE 17.1"" WXGA"
"LCD CABLE 17.1""
WXGA HT MYALL "
50.TCBV1.005
N/A
"LCD CABLE 17.1"" WXGA"
"C.A. 17.1"" WXGA HT
MYALL-2
"
50.ADFV1.001
N/A
MODEM CABLE
MDC CABLE HT
MYALL
50.TCBV1.006
N/A
CABLE
N/A
94
Chapter 6
CATEGORY
N/A
PART NAME
DESCRIPTION
ACER PART
NO.
POWER CORD 10A 250V
3PIN ITALY
CORD 10A 250V 3P
ITALY BK
27.01518.711?
POWER CORD 10A 250V
3PIN ITALY
CORD ITALY 10A
250V 3P BK
27.01518.611
POWER CORD 10A 250V
SWISS
CODE 10A 250V 3P
SWISS BK
27.01518.691
POWER CORD 10A 250V
SWISS
CODE SWISS
POWER 10A 250V BK
27.01518.581
POWER CORD 10A 250V
3PIN BK SOUTH AFRICA
CODE 16A 250V
SOUTH AFRICA BK
27.01518.681
POWER CORD 10A 250V
3PIN BK SOUTH AFRICA
CODE SOUTH
AFRICA 10A 250V BK
27.01518.571
POWER CORD 7A 250V 2PIN
KOREAN
CODE 7A250V 2P
1830 KOREAN
27.01518.531
POWER CORD 7A 125V 2PIN
JAPEN
CODE JAPAN 7A 125V
2P BK
27.01518.551
POWER CORD 2.5A 250V
AUSTRALIA
CODE 2.5A 250V
AUSTRALIA BK
27.01518.621
POWER CORD 10A 125V
3PIN US BK
CODE 10A 125V 3P
US BK
27.01518.641
POWER CORD 10A 125V US
CODE US 10A 125V
BK
27.T30V1.001
POWER CORD 10A 250V
3PIN CHINA BK
CORD 10A 250V 3P
CHINA BK
27.01518.701
POWER CORD 10A 250V
3PIN CHINA
CORD CHINA 10A
250V 3P
27.01518.591
POWER CORD 10A 250V
SOUTH AFRICA BK
CORD 10A 250V
SOUTH AFRICA BK
27.01518.721
POWER CORD 2.5A 250V
SOUTH AFRICA BK
CORD 2.5A 250V
SOUTH AFRICA BK
27.01518.631
POWER CABLE 16A 250V
3PIN EUR BK
CORD 16A 250V 3P
EUR BK
27.01518.731
POWER CORD 220V 3PIN
EUR
CORD EUR 220V 3P
BK
27.T30V1.004
POWER CORD 2.5A 125V
USA
CORD USA/W CNS
2.5A 125V 8121-
27.01518.781
POWER CORD 5A 250V 3PIN
UK BK
CODE 5A 250V 3P UK
BK
27.03118.001
POWER CORD 3A 250V 3PIN
UK
CODE UK 3A 250V 3P
BK
27.01518.541
POWER CORD ACA / ACNZ
POWER CODE ACA /
ACNZ ANNIE
27.03218.021
POWER CODE 7A 125V 2PIN
JAPAN
CODE 7A 125V JAPAN
2PIN BK
27.03518.161
POWER CODE 10A 250V
3PIN DENMARK BK
CODE 10A 250V 3P
DENMARK BK
27.01518.671
POWER CORD 10A 3PIN BK
CODE DENMARK 10A
3P BK
27.01518.561
CASE / COVER / BRACKET ASSEMBLY
Chapter 6
95
CATEGORY
N/A
96
PART NAME
DESCRIPTION
ACER PART
NO.
MIDDLE COVER
ASSY MIDDLE
COVER--AS MYALL
60.ACKV1.003
MINI PCI COVER
ASSY MINIPCI
COVER MYALL
42.TCBV1.003
MINI CARD COVER
ASSY MINICARD
COVER MYALL
42.TCBV1.004
HDD COVER
ASSY HDD COVER
MYALL
42.ACKV1.001
DIMM COVER
ASSY DIMM COVER
MYALL
42.TCBV1.002
LED BOARD SUPPORT
BRACKET
U-CASE SUP. BKT L
MYALL
33.TCBV1.001
OPTICAL BRACKET
ODD BRKT MYALL
33.TCBV1.002
UPPER CASE W/COVER
SWITCH CABLE
ASSY U_CASE--AS
SLIDE MYALL2
60.ADFV1.002
LOWER CASE W/SPEAKER
ASSY L-CASE W/O
CARD READER
60.ADFV1.001
COMBO BEZEL
ASSY COMBO ODD
BEZEL GB
42.TCBV1.011
Chapter 6
CATEGORY
N/A
PART NAME
DESCRIPTION
ACER PART
NO.
DVD DUAL BEZEL
ASSY DVD_DUAL
ODD BEZEL
42.TCBV1.012
DVD SUPER MULIA BEZEL
ASSY S_MULTI ODD
BEZEL GBASE
42.TCBV1.013
DVD SUPER MULIA BEZEL
ASSY ODD SLOT-IN
BEZEL
42.TCBV1.014
HDD CHASSIS
ASSY HDD CHASSIS
MYALL
33.TCBV1.003
"LCD PANEL 17.1"" W/LOGO"
"ASSY LCD 17.1""
PANEL-AS MYALL "
60.ACKV1.005
"LCD BEZEL 17.1"" W/LOGO"
"ASSY LCD BEZEL
17.1"" MYALL
"
60.TCBV1.004
HINGE PACK LEFT/RIGHT
"HINGE PACK 17""
LEFT/RIGHT"
6K.TCBV1.001
LCD BARCKET LEFT
"BRKT LCD 17.1"" L
MYALL
"
33.TCBV1.005
LCD BRACKET RIGHT
"BRKT LCD 17.1"" R
MYALL
"
33.TCBV1.004
N/A
CAMERA HOLDER
HLDR CAMERA SIDE
RIM KIRKINI
42.ADFV1.001
N/A
CAMERA LOWER CASE CAS
CAS CAMERA LCASE KIRKINI
39.ADFV1.001
N/A
CAMERA HOLDER CAP
HLDR CAMERA CAP
KIRKINI
42.ADFV1.002
N/A
CAMERA LATCH
LATCH CAMERA
HINGH KIRKINI
33.ADFV1.003
N/A
CAMERA LOWER CASE
ASSY CAMERA
LCASE KIRKINI
60.ADFV1.006
SPEAKER LEFT/RIGHT
SPEAKER MYALL
23.TCBV1.001
SPEAKER
N/A
COMBO MODULE
Chapter 6
97
CATEGORY
PART NAME
DESCRIPTION
ACER PART
NO.
COMBO MODULE 24X
ASSY ODD COMBO
MYALL2
6M.ADFV1.001
CDRW/DVD COMBO DRIVE
24X PHILIPS SCB5265 W/O
BEZEL
COMBO PHI/SCB5265
MYALL NOBZL
KO.02408.010
CDRW/DVD COMBO DRIVE
24X LITEON SOSC-2485K
W/O BEZEL
COMBO LIT/SOSC2485K NO BZL
KO.02409.022
DVD-RW DRIVE 8X DUAL
ASSY ODD DUAL
MYALL2
6M.ADFV1.002
DVD-RW DRIVE 8X DUAL
TS-L532U W/O BEZEL
DUAL TOS/TS-L532U
W/BOLSENA BZ
KU.00801.005
DVD-RW DRIVE 8X DUAL
PHILIPS SDVD8441 W/O
BEZEL
DUAL PHI/SDVD8441
NO BZL MORAR
KU.00809.002
DVD-RW DRIVE 8X SUPER
MULTI SLOT IN
ASSY ODD S-MULTI
MYALL2
6M.ADFV1.003
DVD-RW DRIVE 8X SUPER
MULTI SLOT IN TOSHIBA TSL632D W/O BEZEL
S-MULT 8X TST/TSL632D W/O BZL
KU.00801.014
DVD-RW DRIVE 8X SUPER
MULTI SLOT IN LITEON
SSM-8515S W/O BEZEL
S-MULTI LTN/SSM8515S BOLSEN-E
KU.00804.022
DVD-RW DRIVE 8X SUPER
MULTI SLOT IN PHI SDVD8821 W/O BEZEL
SUP-MULT PHI/SDVD8821 KERKINI
KU.00809.005
DVD-RW DRIVE 8X SUPER
MULTI SLOT IN LITEON
SSM-8515S W/O BEZEL
S-MULTI LTN/SSM8515S MYALL/2
KU.00804.037
DVD-RW DRIVE 8X SUPER
MULTI SLOT IN
ASSY ODD SLOT-IN
PIONEER
6M.ADFV1.004
DVD-RW DRIVE 8X SUPER
MULTI SLOT IN PIONEER
DVR-K06RS W/O BEZEL
SUP-MULT PIO/DVRK06RS SLOT LF
KU.00805.027
DVD-RW DRIVE 8X SUPER
MULTI SLOT IN
ASSY ODD SLOT-IN
PANASONIC
6M.ADFV1.005
DVD-RW DRIVE 8X SUPER
MULTI SLOT IN PANASONIC
UJ-855 W/O BEZEL
SUP-MULT PAN/UJ845 SLOT LF AG
KU.00807.029
DVD-RW DRIVE
N/A
CPU
98
Chapter 6
CATEGORY
PART NAME
DESCRIPTION
ACER PART
NO.
CPU DC YONAH T2300
1.66GMHZ INTEL
IC CPU DC YONAH
T2300 1.66G PGA
KC.23001.DTP
CPU DC YONAH T2600
2.17GMHZ INTEL
IC CPU DC YONAH
T2600 2.17G PGA
KC.26001.DTP
CPU DC YONAH T2500
2GMHZ INTEL
IC CPU DC YONAH
T2500 2G PGA
KC.25001.DTP
CPU DC YONAH T2400
1.83GMHZ INTEL
IC CPU DC YONAH
T2400 1.83G PGA
KC.24001.DTP
CPU DC YONAH T2300
1.66GMHZ INTEL
IC CPU DC YONAH
T2300 1.66 PGA
KC.23E01.DTP
CPU YONAH CEL-M 430
1.73GNHZ INTEL
IC CPU YONAH CELM 430 1.73 PGA
KC.N0001.430
CPU YONAH CEL-M 420
1.6GMHZ INTEL
IC CPU YONAH CELM 420 1.6 PGA
KC.N0001.420
FAN
FAN SUNON MYALL
23.TCBV1.004
FAN
FAN FORCECON
MYALL
23.TCBV1.004
FAN
FAN KME MYALL
23.TCBV1.004
FAN
HDD
Chapter 6
99
CATEGORY
N/A
100
PART NAME
DESCRIPTION
ACER PART
NO.
HDD 60G 4200RPM
SEAGATE ST960812A
HDD 60GB SEAGATE
ST960812A
KH.06001.006
HDD 60G HITACHI
HTS421260H9AT00
HDD 60GB HGST
HTS421260H9AT00
KH.06007.009
HDD 60G 4200RPM
TOSHIBA MK6025GAS
HDD 60GB TOSHIBA
MK6025GAS
KH.06004.004
HDD 60G 5400RPM
SEAGATE ST96812A
HDD 60GB SEAGATE
ST96812A
KH.06001.007
HDD 60G 5400RPM
TOSHIBA
HDD 60GB TOSHIBA
5400RPM
KH.06004.007
HDD 60G 5400RPM HITACHI
HTS541260H9AT00
HDD 60GB HGST
HTS541260H9AT00
KH.06007.011
HDD 80G 4200RPM
SEAGATE ST980829A
HDD 80GB SEAGATE
ST980829A
KH.08001.021
HDD 80G 4200RPM HITACHI
HTS421280H9AT00
HDD 80GB HGST
HTS421280H9AT00
KH.08007.011
HDD 80G 4200RPM
TOSHIBA MK8025GAS
HDD 80GB TOSHIBA
MK8025GAS
KH.08004.003
HDD 80G 5400RPM
SEAGATE ST98823A
HDD 80GB SEAGATE
ST98823A
KH.08001.022
HDD 80G 5400RPM WD
WD800UE-22HCT0
HDD 80GB WD
WD800UE-22HCT0
KH.08008.027
HDD 80G 5400RPM
TOSHIBA
HDD 80GB TOSHIBA
5400RPM
KH.08004.006
HDD 80G 5400RPM HITACHI
"HDD 80G 2.5""
5400RPM HGST"
KH.08007.013
HDD 100G 4200RPM
SEAGATE ST9100825A
HDD 100GB
SEAGATE
ST9100825A
KH.10001.006
HDD 100G HITACHI
HTS421210H9AT00
HDD 100GB HGST
HTS421210H9AT00
KH.10007.002
HDD 100G TOSHIBA
MK1031GAS
HDD 100GB TOSHIBA
MK1031GAS
KH.10004.001
HDD 100G 5400RPM
HITACHI 13G1591 ROHS
HDD 100GB HGST
13G1591 ROHS
KH.10007.004
HDD 100G 5400RPM
SEAGATE ST9100824A
HDD 100GB
SEAGATE
ST9100824A
KH.10001.007
HDD 100G 5400RPM
TOSHIBA MK1032GAX
HDD 100GB TOSHIBA
MK1032GAX
KH.10004.002
HDD 100G 5400RPM
SAMSUNG HM100JC
HDD 100GB
SAMSUNG HM100JC
KH.1000B.002
HDD 120G HITACHI
HTS421212H9AT00
HDD 120GB HGST
HTS421212H9AT00
KH.12007.008
HDD 120G 4300RPM
SEAGATE ST9120824A
HDD 120GB
SEAGATE
ST9120824A
KH.12001.023
HDD 120G 4200RPM
SEAGATE MK1233GAS
HDD 120G
MK1233GAS
4200RPM ROH
KH.12004.001
Chapter 6
CATEGORY
N/A
ACER PART
NO.
PART NAME
DESCRIPTION
HDD 120G 4200RPM
HITACHI 0A26308
HDD 120GB HGST
0A26308 ROHS
KH.12007.006
HDD 120G 5400RPM
SEAGATE ST9120821A
HDD 120GB
SEAGATE
ST9120821A
KH.12001.024
HDD 120G 5400RPM
TOSHIBA
HDD 120GB TOSHIBA
5400RPM
KH.12004.002
HDD 160G 5400RPM
SEAGATE ST9160821A
HDD 160GB
SEAGATE
ST9160821A
KH.12001.024
CPU HEATSINK
ASSY CPU HSINK CCI
UMA MYALL
34.TBHV1.001
AS9400/7100 KEYBOARD
DARFON US
INTERNATIONAL
AS9400/7100
KEYBOARD DARFON
US INTERNATIONAL
KB.ACF07.001
AS9400/7100 KEYBOARD
DARFON CHINESE
AS9400/7100
KEYBOARD DARFON
CHINESE
KB.ACF07.002
AS9400/7100 KEYBOARD
DARFON SPANISH
AS9400/7100
KEYBOARD DARFON
SPANISH
KB.ACF07.003
AS9400/7100 KEYBOARD
DARFON THAI
AS9400/7100
KEYBOARD DARFON
THAI
KB.ACF07.004
AS9400/7100 KEYBOARD
DARFON BRAZILIAN
PROTUGESE
AS9400/7100
KEYBOARD DARFON
BRAZILIAN
PROTUGESE
KB.ACF07.005
AS9400/7100 KEYBOARD
DARFON KOREA
AS9400/7100
KEYBOARD DARFON
KOREA
KB.ACF07.006
AS9400/7100 KEYBOARD
DARFON UK
AS9400/7100
KEYBOARD DARFON
UK
KB.ACF07.007
AS9400/7100 KEYBOARD
DARFON GERMAN
AS9400/7100
KEYBOARD DARFON
GERMAN
KB.ACF07.008
AS9400/7100 KEYBOARD
DARFON ITALIAN
AS9400/7100
KEYBOARD DARFON
ITALIAN
KB.ACF07.009
AS9400/7100 KEYBOARD
DARFON FRENCH
AS9400/7100
KEYBOARD DARFON
FRENCH
KB.ACF07.010
HEATSINK
KEYBOARD
Chapter 6
101
CATEGORY
PART NAME
DESCRIPTION
ACER PART
NO.
AS9400/7100 KEYBOARD
DARFON SWISS/G
AS9400/7100
KEYBOARD DARFON
SWISS/G
KB.ACF07.011
AS9400/7100 KEYBOARD
DARFON PORTUGUESE
AS9400/7100
KEYBOARD DARFON
PORTUGUESE
KB.ACF07.012
AS9400/7100 KEYBOARD
DARFON ARABIC
AS9400/7100
KEYBOARD DARFON
ARABIC
KB.ACF07.013
AS9400/7100 KEYBOARD
DARFON BELGIUM
AS9400/7100
KEYBOARD DARFON
BELGIUM
KB.ACF07.014
AS9400/7100 KEYBOARD
DARFON SWEDEN
AS9400/7100
KEYBOARD DARFON
SWEDEN
KB.ACF07.015
AS9400/7100 KEYBOARD
DARFON CZECH
AS9400/7100
KEYBOARD DARFON
CZECH
KB.ACF07.016
AS9400/7100 KEYBOARD
DARFON HUNGAIAN
AS9400/7100
KEYBOARD DARFON
HUNGAIAN
KB.ACF07.017
AS9400/7100 KEYBOARD
DARFON NORWAY
AS9400/7100
KEYBOARD DARFON
NORWAY
KB.ACF07.018
AS9400/7100 KEYBOARD
DARFON DANISH
AS9400/7100
KEYBOARD DARFON
DANISH
KB.ACF07.019
AS9400/7100 KEYBOARD
DARFON TURKISH
AS9400/7100
KEYBOARD DARFON
TURKISH
KB.ACF07.020
AS9400/7100 KEYBOARD
DARFON CANADIAN
FRENCH
AS9400/7100
KEYBOARD DARFON
CANADIAN FRENCH
KB.ACF07.022
AS9400/7100 KEYBOARD
DARFON GREEK
AS9400/7100
KEYBOARD DARFON
GREEK
KB.ACF07.024
AS9400/7100 KEYBOARD
DARFON HEBREW
AS9400/7100
KEYBOARD DARFON
HEBREW
KB.ACF07.025
AS9400/7100 KEYBOARD
DARFON RUSSIAN
AS9400/7100
KEYBOARD DARFON
RUSSIAN
KB.ACF07.026
AS9400/7100 KEYBOARD
DARFON SLOVENIA (SLO)
AS9400/7100
KEYBOARD DARFON
SLOVENIA (SLO)
KB.ACF07.027
WIRELESS ANTENNA
ANTENNA CABLE
MYALL2
25.ADFV1.001
"ASSY LCD MODULE 17""
WXGA GLARE"
"ASSY 17"" LCD
GLARE AS
"
6M.ADFV1.011
COMMUNICATION MODULE
N/A
LCD
N/A
102
Chapter 6
CATEGORY
PART NAME
ACER PART
NO.
DESCRIPTION
N/A
"LCD 17"" WXGA+ LG
LP171WP4-TL02 GLARE"
"LCD 17""W
LP171WP4-TL02
GLARE"
LK.17008.015
N/A
"LCD 17.1"" WXGA+ QDI
QD17TL02-05 NONE GLARE
"
"LCD 17""W QDI
QD17TL02-05"
LK.17109.001
N/A
"LCD 17""WXGA+ QDI
QD17TL02-06 GLARE"
"LCD 17"" QD17TL0206 GLARE"
LK.17109.002
N/A
"LCD 17.1"" WXGA+
SAMSUNG LTN170WX-L05
NONE GLARE
"
"LCD 17""W
LTN170WX-L05
N/A
"LCD 17"" WXGA+
SAMSUNG LTN170WX-L05-H
GLARE"
"LCD 17""W
LTN170WX-L05-H
GLARE"
LK.17106.002
N/A
"LCD 17"" WXGA+ AU
B170PW03 V4 GLARE "
"LCD 17""WXGA
B170PW03 V4 GLARE
"
LK.17105.005
N/A
"LCD 17.1"" WXGA+ AU
B170PW03 V3 NONE GLARE
"
"LCD 17""W AU
B170PW03 V3"
LK.17105.006
N/A
"ASSY LCD MODULE 17""
WXGA GLARE CCD 1.3M"
"ASSY 17"" LCD
GLARE CCD AS
ASSY LCD MODULE 17"
WXGA GLARE CCD 300K
ASSY 17" 300K CCD
GLARE AS
6M.ADFV1.013
N/A
CAMERA CMOS 1.3M
LOGITECH 961458-2000 L
CAMERA CMOS 1.3M
961458-2000 L
56.ABAV1.001
N/A
CAMERA CMOS 300K VFA
BN2QA350K8SD79
CAMERA CMOS VFA
BN2QA350K8SD79
56.ADFV1.001
MAINBOARD MYALL 2 W/
MODEM & MODEM CABLE &
RTC BATTERY W/O CPU &
MEMORY (Aspire 9410 UMA,
TravleMate 5610 UMA)
MYALL2 MB 06203-1
945GM (D) (Aspire
9410 UMA,
TravelMate 5610
UMA)
MB.TCS01.001
MAINBOARD MYALL 2 W/
MODEM & MODEM CABLE &
RTC BATTERY W/O CPU &
MEMORY (Aspire 9410
DISCRETE)
MYALL2 MB 06203-1
64MB VRAM (D)
(Aspire 9410
DISCRETE)
MB.TCT01.001
MAINBOARD MYALL 2 W/
MODEM & MODEM CABLE &
RTC BATTERY W/O CPU &
MEMORY (Aspire 9410
DISCRETE, TravelMate 5610
DISCRETE)
MYALL2 MB 06203-1
128MB VRAM (D)
( Aspire 9410
DISCRETE,
TravelMate 5610
DISCRETE)
MB.TCU01.001
MAINBOARD MYALL 2 W/
MODEM & MODEM CABLE &
RTC BATTERY W/O CPU &
MEMORY (Aspire 7110 UMA)
MYALL2 MB 06203-1
940GML (D)
(Aspire 7110 UMA)
MB.TCW01.001
N/A
LK.17106.001
"
6M.ADFV1.012
"
CAMERA
MAINBOARD
SLOT
Chapter 6
103
CATEGORY
N/A
PART NAME
DESCRIPTION
ACER PART
NO.
PCMCIA SLOT 4PIN
CONN CARDBUS 4P
59330-00L0C
22.T28V1.001
SDIMM 256M SAMSUNG
470T3354CZ3-CD5
SODIMM 256M
M470T3354CZ3-CD5
KN.2560B.017
SDIMM 256M MICRON
MT4HTF3264HY-53EB4
SODIMM 256M
MT4HTF3264HY53EB4
KN.25604.030
SDIMM 256M HYNIX
HYMP532S64BP6-C4
SODIMM 256M
HYMP532S64BP6-C4
KN.2560G.012
DIMM 256M NANYA
NT256T64UH4A1FN-37B
DIMM 256M
NT256T64UH4A1FN37B
KN.25603.029
SDIMM 256M INFINEON
HYS64T32000HDL-3.7-A
SODIMM256MHYS64
T32000HDL-3.7-A
KN.25602.023
SDIMM 512M NANYA
NT512T64UH8A1FN-37B
SODIMM512M
NT512T64UH8A1FN37B
KN.51203.023
SDIMM 512M SAMSUNG
M470T6554CZ3-CD5
SODIMM 512M
M470T6554CZ3-CD5
KN.5120B.015
SDIMM 512M INFINEON
MHYS64T64020HDL-3.7-A
SODIMM512MHYS64
T64020HDL-3.7-A
KN.51202.021
SDIMM 512M ELPIDA
GU33512AGEPN612C
SODIMM 512M
GU33512AGEPN612C
KN.51209.005
SDIMM 512M HYNIX
HYMP564S64BP6-C4
SODIMM 512M
HYMP564S64BP6-C4
KN.5120G.013
SDIMM 1G
HYS64T128021HDL-3.7-A
SODIMM1G
HYS64T128021HDL3.7-A
KN.1GB02.023
SDIMM 1GB 533 NANYA
SO-DIMM DDRII 533
1GB NANYA
KN.1GB03.006
SDIMM 1G
GU331G0AGEPN6E2C
SODIMM 1G
GU331G0AGEPN6E2
C
KN.1GB09.004
MICROPHONE
MICROPHONE
SUNMOWNG MYALL
23.TCBV1.002
MISCELLANEOUS
LCD SCREW RUBBER
RUB LCD RUBBER
CUSHION BOLSENA
47.A46V1.002
MISCELLANEOUS
LCD SCREW RUBBER
RUBBER SCREW
MYALL
47.TCBV1.001
MISCELLANEOUS
LOGO PLATE FOR PANEL
PLT LOGO PANEL
31.T49V1.001
MISCELLANEOUS
LOGO PLATE FOR BEZEL
"PLT BEZEL PLATE
""ACER "" LOGO "
31.A46V1.001
SCREW
SCW HEX NYL I#R40/O#4-40 L5.5
34.00015.081
MEMORY
MICROPHONE
MICROPHONE
MISCELLANEOUS
SCREW
N/A
104
Chapter 6
CATEGORY
PART NAME
DESCRIPTION
ACER PART
NO.
N/A
SCREW
SCREW MACH
WAFER M2*L4 NI
86.T39V1.002
N/A
SCREW
SCRW M2.5*6 ~ LCASE + U-CASE
86.00D28.330
N/A
SCREW
SCRW M2*L3
86.00D29.620
N/A
SCREW
SCRW M2.5*5 WAFER
B-ZN ROHS
86.00D47.630
N/A
SCREW
SCREW M2*L3
NYLOK CR 3+
86.00E25.723
N/A
SCREW
SCREW M2*L3 NONNYLOK CR3+
86.00E31.723
N/A
SCREW
SCREW M2.5*L6
NYLOK CR3+
86.00E33.736
N/A
SCREW
SCREW M2.5*L8
NYLOK CR3+
86.00E34.738
N/A
SCREW
SCREW M2*L8 NI
NON-NYLOK
86.00E35.228
N/A
SCREW
SCREW
M3x4(86.9A524.4R0)
86.9A524.4R0
N/A
SCREW
SCRW M2*4 WAFER
NI
86.9A552.4R0
N/A
SCREW
SCREW NI M2*6L
86.9A552.6R0
N/A
SCREW
SCRW M2.5*L3(NON
NYLOK)
86.9A523.3R0
Chapter 6
105