Rice Lake CW-90B Installation manual

CW-90/90X
Checkweigher
Installation Manual
To be the best by every measure™
105942
Contents
About This Manual ................................................................................................................................... 1
1.0
Introduction.................................................................................................................................. 1
1.1
1.2
1.3
1.4
2.0
Operating Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Keypad Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Annunciators LEDs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Bar Graph LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation ................................................................................................................................... 4
2.1
2.2
2.3
2.4
2.5
2.6
2.7
Unpacking and Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Leveling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Making Power Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Enclosure Disassembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Load Cell Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Wire Specifics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cable Grounding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.7.1
2.7.2
3.5
3.6
3.7
3.8
3.9
Menu Navigation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Audit Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Calibration Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setup Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
13
14
14
16
3.4.1
3.4.2
3.4.3
3.4.4
SCALE Submenu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FEATUR Submenu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FEATUR Menu, REGULA / INDUST Submenu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Serial, PFORMT, DIG I/O, VERS Submenus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
16
20
24
26
Test Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Time and Date Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ACCUM Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
BRIGHT Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ID Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
29
30
31
31
31
Calibration ................................................................................................................................. 33
4.1
4.2
4.3
4.4
Front Panel Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
EDP Command Calibration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Revolution® Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
More About Calibration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.4.1
5.0
7
7
7
7
9
Configuration ............................................................................................................................. 13
3.1
3.2
3.3
3.4
4.0
4
5
5
5
5
5
5
Serial Communications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Digital I/O . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.8 Enclosure Reassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.9 Board Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.10 Battery Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.11 Installing Option Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.12 Replacement Parts and Assembly Drawings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.0
1
1
2
3
33
34
35
35
Adjusting Final Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Checkweigher Operation ........................................................................................................... 36
5.1 Range Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
5FDIOJDBMUSBJOJOHTFNJOBSTBSFBWBJMBCMFUISPVHI3JDF-BLF8FJHIJOH4ZTUFNT
$PVSTFEFTDSJQUJPOTBOEEBUFTDBOCFWJFXFEBUXXXSJDFMBLFDPNPSPCUBJOFECZ
DBMMJOHBOEBTLJOHGPSUIFUSBJOJOHEFQBSUNFOU
© 2009 Rice Lake Weighing Systems. All rights reserved. Printed in the United States of America.
Specifications subject to change without notice.
July 22 2009
i
5.1.1
5.1.2
Value Set: Keyed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Value Set: Push . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
5.2 Target Weight Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
5.2.1
5.2.2
Value Set: Keyed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Value Set: Push . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
5.3 Target Percent Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
5.3.1
5.3.2
Value Set: Keyed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Value Set: Push . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
5.4 IDs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
5.4.1
5.4.2
Setting an ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Using a Stored ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
5.5 Negative Checkweighing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
6.0
Serial Commands ...................................................................................................................... 43
6.1 The Serial Command Set. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
6.1.1
6.1.2
6.1.3
6.1.4
6.1.5
6.1.6
6.1.7
Key Press Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ID Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Reporting Commands. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Clear and Reset Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Parameter Setting Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Normal Mode Commands. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Unique Commands. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
43
44
44
44
44
48
48
6.2 Custom Stream Formatting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
7.0
Print Formatting ......................................................................................................................... 51
7.1 Print Formatting Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
7.2 Customizing Print Formats. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
7.2.1
7.2.2
7.2.3
8.0
Using the EDP Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Using the Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Using Revolution® III . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
WLAN Installation Instructions .................................................................................................. 54
8.1 Enclosure Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.2 Installing the WLAN Option Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.3 Mounting the Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.4 Wireless Configuration via Serial Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.5 Jumpers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.6 WLAN Card Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.7 Enclosure Reassembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.8 WiPort Wireless Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.9 WiPort Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.10 WiPort Disclaimer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9.0
54
55
55
56
56
56
62
62
63
64
Appendix .................................................................................................................................... 65
9.1 Error Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
9.2 Using the XE EDP Command. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
9.3 Status Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
9.3.1
9.3.2
Using the P EDP Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Using the ZZ EDP Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
9.4 Continuous Output (Stream) Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
9.5 Digital Filtering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
9.5.1
9.5.2
9.5.3
9.5.4
DIGFLx Parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DFSENS and DFTHRH Parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setting the Digital Filter Parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Audit Trail Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
68
68
68
68
9.6 Regulatory Mode Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
9.7 Updating CW-90/90X Firmware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
9.8 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
CW-90/90X Limited Warranty ................................................................................................................ 74
ii
CW-90/90X Installation Manual
About This Manual
This manual is intended for use by qualified service
technicians responsible for installing and servicing the
CW-90/CW-90X checkweighing scale.
Warning
1.0
Do not open the indicator enclosure!
Refer all repairs and modifications to your
distributor or qualified service technician.
Ensure power is disconnected prior to
installing, servicing, transporting, or
storing equipment.
Introduction
The CW-90/CW-90X is a high-speed digital weight
indicator and scale base programmed to compare
weight readings with predetermined tolerance limits
defining an “accept” band.
If the current weight reading is within the acceptable
range, the green “ACCEPT” LED is illuminated. If
the current weight reading is less than the acceptable
range, one or more of the red “UNDER” segments is
illuminated. If the current weight reading is greater
than the acceptable range, one or more of the yellow
“OVER” segments is illuminated.
Features include:
• Large .8” (20.3 mm) LED display with
“under,” “accept,” and “over” bands
• Full numeric keypad (CW-90 only)
• Four configurable digital inputs/outputs
• Two independent communication ports (2)
full duplex, (1) unidirectional active 20 mA
current loop
1.1
Authorized distributors and their employees
can view or download this manual from the
Rice Lake Weighing Systems distributor
site at www.ricelake.com.
1.2
Keypad Functions
Key
Turns the CW-90/CW-90X unit on/off.
NOTE: If the PC jumper is set to SW, the
POWER button must be used to turn the unit
on and off. If the PC jumper is set to ON, the
unit will automatically power on when it’s
plugged in and the only way to turn it off is to
unplug power.
Enters Menu mode, allowing configuration if the
Audit jumper is in the “ON” position. Also used
as an “escape” key in Menu mode.
Sets the current gross weight to zero, provided
the amount of weight to be removed or added
is within the specified zero range and the scale
is not in motion. The zero band is defaulted to
1.9% of full scale, but can be configured for up
to 100% of full scale.
NOTE: 1.9% is required for legal for trade
applications.
Operating Modes
Switches the weight display to an alternate unit.
The alternate unit is defined in the Setup menu,
and could be kg, g, lb, oz, or lb/oz.
Conversions of the weight reading, the Tare
value, the Over value, and the Under value
occur when the unit of measure is changed
with the Units key.
The CW-90/CW-90X has two modes of operation:
Normal (Weighing) Mode
Normal mode is the “production” mode of the
indicator. The indicator displays the gross or net
weight, depending on whether a tare has been entered.
LED annunciators indicate the type of weight value.
Sends “on-demand” serial information out the
serial port, provided the conditions for standstill
are met.
Menu mode
Most of the procedures described in this manual,
including configuration and calibration, require the
indicator to be in Menu mode.To enter Menu mode,
press the MENU key (if the Audit jumper is in the
“ON” position).The indicator displays “AUDIT.”
If the Audit jumper is in the “OFF” position, remove
the large fillister head screw from the bottom of the
enclosure. Insert a screwdriver into the access hole
and press the setup switch once to enter Menu mode.
Function
Performs one of several predetermined Tare
functions dependent on the mode of operation
selected in the TAREFN parameter (See
Section 3.4.1 on page 16).
OVER
Allows the display of the current “over
tolerance” value, or allows setting the “over
tolerance” value.
Table 1-1. Keypad functions
Introduction
1
Key
Function
UNDER
Allows the display of the current “under
tolerance” value, or allows setting the current
“under tolerance” value.
When the MODE parameter is set to TARGWT
or TARG% (see Section 3.4.2 on page 20), this
key is used to acquire a weight value and
assign it as the desired “target” value. The
CW-90/CW-90X then computes the final
over/under values using the target value and
the over/under tolerance settings defined
during the weighing operation.
TARGET
Selects a particular over/under/tare/units
register set to be retrieved and used.
ID
Used to accept entries and move down to
below parameters in Menu mode.
ENTER
CW-90 only.
Clear key. Used to backspace on entries
Numeric keypad
(see Figure 1-1)
CW-90 only.
Used to enter values directly.
Table 1-1. Keypad functions
1.3
Annunciators LEDs
LED
Description
Zero (Center of Zero) LED
While in gross weight display mode, this LED
indicates that the current displayed weight
reading is within +/-0.25 display divisions of the
acquired zero, or is within the center of zero
band.
When in the net weight display mode, it
indicates that the current net weight reading is
within +/-0.25 display divisions of the center of
net zero. A display division is the resolution of
the displayed weight value, or the smallest
incremental increase or decrease that can be
displayed or printed.
G/B LED
Gross weight mode (or Brutto in OIML mode)
N LED
Net weight display mode.
T LED
Indicates that a tare has been acquired and
stored by the system.
PT LED
Indicates that a preset tare weight has been
keyed in or entered via the EDP serial port.
Displays which unit of measure is being used.
% LED
Percent mode
kg LED
Kilograms
g LED
Grams
lb LED
Pounds
oz LED
Ounces
Table 1-2. Annunciator LEDs
Figure 1-1. CW-90 numeric keypad
2
CW-90/90X Installation Manual
1.4
Bar Graph LEDs
The bar graph LEDs provide you with a fast way of determining if a container is too heavy (OVER), too light
(UNDER), or is within an acceptable weight range (ACCEPT).
UNDER
OVER
ACCEPT
Slightly under
Moderately under
Slightly over
Moderately over
Greatly over
Greatly under
Acceptable weight
Figure 1-2. Bar graph LEDs
You can enable the UNDER and OVER lights to act as a graph as illustrated in Figure 1-2, or to appear as one a
solid bar regardless to how far over/under a weighment is. This is done by accessing the Feature menu (see
Section 3.4.2 on page 20).
Red Segments
When illuminated, this indicates an underweight condition; the container weighs less than the lowest acceptable
value. The leftmost red segments indicate that the container weight is far below the acceptable weight band
(greatly under); the rightmost segments indicate that the container weight is almost in the acceptable weight
band, but still under (slightly under). Illuminating the center segments indicates middle-ground, or moderately
under.
Green Segment
Indicates an acceptable value. When lit, the green segment (one solid bar) indicates that the container weight is
within the actual acceptable band of weight limits.
Yellow Segments
When illuminated, this indicates an overweight condition; the container weighs more than the highest acceptable
value. The rightmost yellow segments indicate that the container weight is far above the acceptable weight band
(greatly over); the leftmost segments indicate that the container weight is almost in the acceptable weight band,
but still over (slightly over). Illuminating the center segments indicates middle-ground, or moderately over.
Introduction
3
2.0
Installation
This section contains instructions on unpacking and assembly, leveling, making power connections, load cell
wiring, wiring standard serial port, optional network communications, wiring optional digital outputs, optional
backup battery operation, board diagrams, and power-up sequence.
Do not pick up the scale by the “spider” assembly which supports the platter. Lifting by the
spider may damage the load cell. Lift the scale from under the base to move it. If the rear panel
of the indicator is removed, align the gasket holes carefully to prevent driving a screw through
the gasket and causing a leak. Tighten screws to 15 in/lbs (1.7 N-m) in alternating patterns shown Figure 2-1.
10
1
8
Torque Pattern 3
5
6
4
7
2
9
Figure 2-1. Indicator back panel screw tightening sequence
2.1
Unpacking and Assembly
The indicator head and support column or stand are shipped detached from the scale platform.
1. Remove all assemblies from the shipping carton. Notice that the head and scale platform are joined by a
load cell cable. This cable is correctly wired to the load cell terminal in the indicator head. Do not pull
with excessive force on the connections at either end of this cable.
2. If mounting the head onto a column, remove the platter from the scale platform and set aside.
3. Invert the platform to access the column mounting holes on the rear and bottom of the platform.
4. Position the column over the four mounting holes. Install (2) 1/4-20 x 3/4” cap screws and (2) lock
washers in mounting holes on bottom side of the platform. Install (2) 1/4-20 x 1-3/4”cap screws, (2) lock
washers, and (2) column supports in mounting holes on rear of platform. Install coupling nuts, counter
bored end first, onto threaded stem of rubber feet. Install feet onto bottom side of the column.
5. Turn the CW-90/90X upright and replace the platter on the platform.
6. Attach indicator to the column with the two knobs and nylon washers provided. Position nylon washers
between indicator enclosure and column mounting holes.
Indicator
Column
Column Support
Lock Washer
Cap Screw 1/4-20NC x 1-3/4
Coupling Nut
Foot
Lock Washer
Cap Screw 1/4-20NC X 3/4
Figure 2-2. Mounting column to scale platform
4
CW-90/90X Installation Manual
2.2
Leveling
Select a location for the CW-90/90X that is reasonably
level and free of vibrations and air currents. Adjust the
four corner feet on the base and refer to the bubble
level on the inside frame. The base should not rock
and the feet should have solid contact with the
surface. If using a column, adjust the two column feet
until they make solid contact with the support surface.
J1 Pin
Function
1
+ Signal
2
- Signal
3
+ Sense
4
- Sense
5
+ Excitation
NOTE: Ensure the nut on each foot’s bolt is secured flush
against the scale base.
6
- Excitation
2.3
Making Power Connections
The power source used for the CW-90 must be
properly grounded to an acceptable earth ground. If
the indicator is remotely mounted, the platform must
be separately grounded from the chassis ground screw
located on the bottom of the platform. Connect this
screw with 18 gauge wire to the same earth ground
system as the AC power source. Failure to ground the
base may cause static buildup and incorrect weights.
NOTE: The CW-90 must be installed near an easily accessible
power outlet to allow for quick disconnect in case of
emergency.
2.4
Enclosure Disassembly
The indicator enclosure must be opened to connect
cables for load cells, communications, and digital
inputs/outputs.
Before opening the unit, ensure the
power cord is disconnected from the
power outlet. The power outlet must be located near the
indicator to allow the operator to easily disconnect power
to the unit.
Warning
Ensure power to the indicator is disconnected, then
place the indicator face-down on an antistatic mat.
Remove the screws holding the backplate to the
enclosure body, then lift the backplate away from the
enclosure and set it aside.
2.5
Load Cell Wiring
On all complete units (indicator head and base), the
load cell has been wired to the indicator’s CPU load
cell terminal at the factory. If you have purchased just
the indicator head, you must wire the load cell.
Wire the cable to the CPU board’s J1 connector as
shown in Table 2-1. Leave any excess cable outside of
the indicator head during installation
NOTE: If using a 4-wire connection, set JP1 and JP2 to ON. If
using a 6-wire connection, set JP1 and JP2 to OFF.
Table 2-1. J1 pin assignments
2.6
Wire Specifics
Wires connecting to J1, J2, J3, or J4 should adhere to
the following specifications:
Wire Range
Wire Strip Length
28~12 AWG stranded or solid wire
5~6 mm (3/16” ~ 1/4”)
Table 2-2. Wire specifications for connectors
2.7
Cable Grounding
Except for the power cord, all cables routed through
the cord grips should be grounded against the
indicator enclosure. Do the following to ground
shielded cables.
• Use the lockwashers, clamps, and kep nuts
provided in the parts kit to install grounding
clamps on the enclosure studs adjacent to cord
grips. Install grounding clamps only for cord
grips that will be used; do not tighten nuts.
• Route cables through cord grips and
grounding clamps to determine cable lengths
required to reach cable connectors. Mark
cables to remove insulation and shield as
described below:
• For cables with foil shielding, strip insulation
and foil from the cable half an inch (15 mm)
past the grounding clamp (see Figure 2-3).
Fold the foil shield back on the cable where
the cable passes through the clamp. Ensure
silver (conductive) side of foil is turned
outward for contact with the grounding
clamp.
• For cables with braided shielding, strip cable
insulation and braided shield from a point just
past the grounding clamp. Strip another half
inch (15 mm) of insulation only to expose the
braid where the cable passes through the
clamp (see Figure 2-3 on page 6).
• Finish installation using cable mounts and ties
to secure cables inside of indicator enclosure.
Installation
5
2.7.2
NOTE: Install lockwashers
first, against backplate,
under grounding clamp
Cord grip
Insulated cable
Foil (silver side out)
Cut insulation here
for braided cables
Braid
Grounding clamp
Cut insulation here
for foil-shielded cables
Shield wire (cut)
Length of foil before folding
back on cable insulation
Figure 2-3. Grounding Clamp Attachment for Foil-Shielded
and Braided Cabling
2.7.1
Serial Communications
Wire the serial communications cables to J2, which is
Port 1 (5-wire RS-232 port). J3 is Port 2 (RS-232 and
20 mA). Connect communications cables to J2 and J3
as shown in Table 2-3.
Use cable ties to secure serial cables to the inside of
the enclosure.
Port 1 supports full duplex RS-232 communications
only; Port 2 provides either active 20 mA output or
d up l e x R S - 2 32 t r a n s m i s s i o n . B ot h p or t s a r e
configured using the SERIAL menu. See
Section 3.4.4 on page 26.
Connector
Pin
Signal
J2
1
Ground
2
Ground
3
Tx
J3
4
Rx
5
DTR
6
RTS
1
20mA+
2
Ground
3
Tx
4
Rx
5
CTS
6
Digital I/O
The Digital I/O can be configured as either digital
inputs or digital outputs as determined by the DIO
menu (see Section 3.4.4 on page 26). The inputs are
active (on) with low voltage (0 VDC) and can be
driven by TTL or 5V logic without additional
hardware. Use the DIG I/O menu (see Section 3.4.4
on page 26) to configure the digital inputs. LEDs on
the CPU board light when digital inputs are active (see
Figure 2-4).
Digital outputs are typically used to control relays that
drive other equipment. Outputs are designed to sink
not source, switching current. Each output is a
normally open connector circuit, capable of sinking
24 mA when active. Digital outputs are wired to
switch relays when the digital output is active (low, 0
VDC) with reference to 5 VDC supply. LEDs on the
CPU board light up when the digital outputs are active
(see Figure 2-4).
Port
1
DIO lights
Screws
2
RTS
Table 2-3. J2 and J3 pin assignments
Figure 2-4. Digital I/O lights and screw locations
Connector
Pin
Signal
J4
1
+5V
2
Ground
3
DIG I/O 1
4
DIG I/0 2
5
DIG I/O 3
6
DIG I/O 4
Table 2-4. J4 Pin Assignments (Digital I/0)
6
CW-90/90X Installation Manual
2.8
Enclosure Reassembly
Once the cabling is complete, position the backplate
over the enclosure and reinstall the screws. Use the
torque pattern shown in Figure 2-1 on page 4 to
prevent distortion. Torque to 15 in/lbs (1.7 N-m).
2.9
Board Removal
If you must remove the CW-90/90X CPU board, use the
following procedure:
1. Disconnect power to the indicator. Remove
backplate as described in Section 2.4 on
page 5.
2. Disconnect power supply cable from
connector J9 on the CW-90/90X CPU board.
3. Disconnect the wires at the following
connectors: J1, J2, J3, J4.
4. There are two boards: the CPU board and the
keypad display board. Remove the five
screws connecting the CPU board (see
Figure 2-4), then lift the board out of the
enclosure.
To replace the CPU board, reverse the above
procedure. Be sure to reinstall cable ties to secure all
cables inside the indicator enclosure.
2.10 Battery Replacement
Risk of explosion if battery is replaced with
incorrect type.
Dispose of batteries per manufacturer
2.11 Installing Option Cards
Option cards are not hot-pluggable.
Disconnect power cord entirely
before installing option cards.
NOTE: Ethernet port is not suitable for connection to circuits
used outside the building and is subject to lightning or power
faults.
Each option card is shipped with installation
instructions specific to that card. For specific
instructions on the WLAN card, refer to Section 8.0
on page 54.
The general procedure for all option cards is:
1. Disconnect power cord from the indicator.
2. Remove the backplate as described in
Section 2.4.
3. Install the plastic standoffs in the standoff
holes (shown as black-shaded circles in
Figure 2-5).
4. Carefully align the option card connector with
the J5 connector on the CPU board.
5. Press down firmly to seat the option card in
the CPU board connector.
6. Make connections to the option card as
required. Use cable ties to secure loose cables
inside the enclosure. When installation is
complete, reassemble the enclosure as
described in Section 2.8.
instructions.
The lithium battery on the CPU board maintains the
real-time clock and protects data stored in the system
RAM when the indicator is not connected to AC
power. Data protected by this battery includes time
and date, IDs, and configuration information. If any
data is lost, the indicator configuration can be restored
from the PC. Watch for the low battery warning on the
LCD display and periodically check the battery
voltage on the CPU board. Batteries should be
replaced when the indicator low battery warning
comes on, or when battery voltage falls to 2.2 VDC.
Life expectancy of the battery is 10 years. Use
Revolution III to store a copy of the configuration
before attempting to replace the battery.
For best results, replace the battery while in weigh
mode and with AC power applied. use care not to
bend the battery retaining spring.
Installation
7
Figure 2-5. CW-90/90X CPU board
Jumper
Description
JP1/JP2
Jump excitation to sense. If using a 4-wire load cell cable, leave JP1 and JP2
on. If using a 6-wire load cell cable, take JP1 and JP2 off. Default is ON.
JP3/JP4
Used when upgrading firmware. The jumpers should be on when upgrading
firmware and off when the update is complete.
PC
Power control. If the jumper is set to SW, the POWER key can be used to turn
the unit on/off. If set to ON, the unit will power on when plugged in and can only
be powered off by unplugging.
JMP1
If set to Audit ON, calibration and configuration can be acessed through the
front keypad. If set to Audit OFF, calibration and configuration can only be
accessed by removing the screw on the base of the unit and pressing the Setup
switch with a screwdriver. Default is Audit ON.
Table 2-5. Jumper descriptions
NOTE: If the RESET button on the CPU board is pressed, the indicator will perform a reboot.
8
CW-90/90X Installation Manual
2.12 Replacement Parts and Assembly Drawings
Ref Number
Part Number
Description (Quantity)
31
103610
Knob, Black 1/4-20 (2)
30
103988
Washer, Nylon .52 ID x (2)
13
104914
104915
Overlay, Membrane Switch (CW-90)
Overlay, Piezo (CW-90X)
--
105945
Parts Kit, CW-90/90X (1)
18
105976
Cable ASSY, Power Supply (1)
19A
102354
CPU (1)
19B
105741
Display (1)
3
14621
Nut, Kep 6-32NC HEX (2)
11
14626
Nut, Kep 8-32NC HEX (3)
16
14822
Screw, MACH 4-40NCx1/4 (6)
17
14825
Screw, MACH 4-40NCx1/4 (4)
27
14862
Screw, MACH 8-32NCx3/8 (4)
10
15134
Washer, Lock NO 8 Type A (3)
34
16861
Label, Warning High (1)
9
16892
Label, Earth Ground (1)
29
29635
Stand, Tilt SST (1)
21
42640
Screw, MACH 1/4-28NF X 1/4 (1)
22
44676
Washer, Bonded Sealing (1)
28
45042
Washer, Bonded Sealing SST (4)
12
45043
Wire, Ground 4in W/No.8 (1)
--
50425
Carton, 13.14x9.00x7.11 (1)
--
53452
Insert, Carton N.J. D/C (1)
8
58983
Cable Grip, SL-7 w/Nut (3)
6
68599
Seal Ring, Nylon PG-11 (1)
5
68600
Cord Grip, PG11 (1)
7
68601
Nut, PG11 (1)
20
69291
Battery, 3v Coin Lithium (1)
15
76556
Power Supply, Switching (1)
24
84388
Gasket, Backplate 420 (1)
4
85202
85203
Power Cord ASSY, 120VAC (1)
Power Cord ASSY, 230VAC (1)
25
88733
Vent, Breather Sealed (1)
26
88734
Nut, Breather Vent (1)
--
107476
Bench Scale Foot
--
105555
Coupling Nut for Feet and Overload Stops
Figure 2-6. CW-90/90X replacement parts
Installation
9
Scale Capacity
Load Cell Part Number
5 lb
107174
10 lb
107174
25 lb
107175
50 lb
107176
100 lb
107177
Table 2-6. CW-90X Load Cells
Scale Capacity
Load Cell Part Number
5 lb
107756
10 lb
107757
25 lb
107758
50 lb
107759
100 lb
107760
Table 2-7. CW-90 Load Cells
Figure 2-7. CW-90/90X front view
10
CW-90/90X Installation Manual
B
A
9
Figure 2-8. CW-90/90X assembly and components
Installation
11
11.24
9.50
3.12
6.00
8.57
10.02
3.75
4.00
10.02
2.01
6.00
.38
3.75 3.00
4x
.281
Figure 2-9. CW-90/90X dimensions
12
CW-90/90X Installation Manual
3.0
Configuration
To set up and configure the CW-90/90X checkweigher, you will either use the Menu key on the front panel or press
the setup switch on the bottom of the indicator. The indicator is defaulted at the factory with the audit trail jumper
(JMP1) in the ON position, allowing configuration access by pressing the Menu key. Pressing the Menu key will
take you to the Audit menu selection. Use the ID ( ) and TARGET ( ) navigation keys to move to other menu
selections. Use the UNDER ( ) and OVER ( ) navigation keys to enter and exit menu selections, respectively.
AUDIT
CALIBR
SETUP
TEST
EXIT
T&D
ACCUM
ID
BRIGHT
Only displayed if
turned on
from Setup menu
Only displayed if
turned on
from Setup menu
Figure 3-1. Menu mode navigation structure
Menu
Function
AUDIT
Audit Trail
Displays the legally relevant (LR) firmware version, configuration count, and calibration count.
CALIBR
Calibrate
Calibrates the scale.
SETUP
Setup
Accesses setup options for the scale, features, serial output, print format, digital inputs and outputs,
and displays the version number.
TEST
Test
Performs a basic test on the A/D, digital inputs and outputs, communication ports, RAM, and keypad.
EXIT
Exit
Exits Configuration mode and returns to the weigh screen.
T&D
Time & Date
Allows you to view and change time and date.
ACCUM
Accumulator
Displays the current accumulator value.
BRIGHT
Brightness
Adjusts display intensity on a scale from 0 (dimmest) to 7 (brightest).
ID
ID
Allows you to setup or edit IDs.
Table 3-1. Menu menu summary
3.1
Menu Navigation
Once you have entered the menus, you can use the front panel buttons to navigate. Note the looped menu
structure shown in Figure 3-1. This provides a shortcut for accessing the rightmost menu items by navigating to
the left, and vice-versa for the opposite side of the menu. This shortcut also holds true for sub-menu navigation.
OVER
Move UP/
Increment
Value
UNDER
Move DOWN/
Decrement
Value
TARGET
ID
MENU
ENTER
Enter Value/
Move DOWN
Move RIGHT/
Next
Move LEFT/
Previous
Backspace
Enters and Exits
Configuration Menu
Figure 3-2. Front Panel Key Functions in Menu mode
NOTE: During calibration, the ENTER key acts as a data entry confirmation key. It also acts as an EXECUTE key, and accepts the
value if calibration was successful. On the CW-90, you can use either the ZERO or CLR key to perform a backspace.
Various keys are used as directional keys to navigate through the menus (see Figure 3-2). The ID ( ) and TARGET
( ) keys scroll left and right (horizontally) on the same menu level; OVER ( ) and UNDER ( ) move up and
down (vertically) to different menu levels. Each of these keys has a directional symbol indicating its menu
navigation function. The ENTER key has the same function as UNDER ( ) when navigating the menu-either will
move down to access sub-categories of a main menu item. When adding or editing data using the CW-90X, the
OVER ( ) and UNDER ( ) keys will edit the blinking digit. The ID ( ) and TARGET ( ) keys navigate to another
digit. This also applies to the CW-90, whose numeric keys can be used to insert a digit to the right of the blinking
digit. Press ENTER to accept the data and return to the next menu item.
NOTE: To exit Configuration and return to weighing, press the MENU key or navigate to the EXIT menu and press ENTER.
Configuration
13
3.2
Audit Menu
The audit menu accesses audit trail support. It provides tracking information for configuration and calibration
events. To prevent potential misuse, all configuration and calibration changes are counted as change events.
Audit information can be printed by pressing the PRINT key while displaying the audit trail items.
AUDIT
CALIBR
XXXXXXX
SETUP
TEST
CALIB
Number
LR,V.
EXIT
T&D
ACCUM
BRIGHT
Only displayed if
turned on
from Setup menu
CONFIG
Number
ID
XXXXXXX
Only displayed if
turned on
from Setup menu
EXIT
Figure 3-3. Audit menu
AUDIT Menu
Parameter
Description
LR.V.
Legally relevant firmware version.
CALIB Number
Displays total calibration events. The display alternates (in one-second intervals) between CALIB and the four-digit number.
CONFIG Number
Displays total configuration events. The display alternates (in one-second intervals) between CFG and the four-digit number.
EXIT
Exits the audit trail and returns to weigh mode.
Table 3-2. Audit menu parameters
3.3
Calibration Menu
See Section 4.0 on page 33 for calibration procedures. The Calibration menu can be protected by assigning a
password in the Feature menu.
NOTE: When entering a floating point value, the decimal point will appear and flash on the far right (if it is not already on the
screen). To move the decimal, press ENTER, then use the
and
keys to move the decimal to the desired location.
The CW-90/90X requires the WZERO and WSPAN points to be calibrated. The linearity points are optional, but must NOT
duplicate zero or span. During calibration, the ENTER key acts as a data entry confirmation key. It also acts as an EXECUTE key,
and accepts the value if calibration was successful.
AUDIT
CALIBR
XXXXXXX
SETUP
TEST
EXIT
T&D
ACCUM
Only displayed if
turned on
from Setup menu
WZERO
Previous A/D raw
counts are shown
Press Enter
to calibrate zero
Press Menu
to cancel
WVAL
WSPAN
Display and edit
test weight value
Previous A/D raw
counts are shown
Press Enter
to calibrate span
Press Menu
to cancel
Calibrating, please wait
PT–> 1
WLI N
REZERO
Calibrating, please wait
Press Enter to
remove offset from
zero and span
calibrations
Calibrating, please wait
PT–> 2
WGT 1
PT–> 3
PT–> 4
PT–> 5
Same as PT->1
CAL1
Figure 3-4. Calibration menu
14
CW-90/90X Installation Manual
BRIGHT
ID
XXXXXXX
Only displayed if
turned on
from Setup menu
CALIBR Menu
Parameter
Choices
Description
Level 2 submenus
WZERO
—
Press ENTER and the A/D raw counts will be displayed.
Press ENTER again to calibrate zero, or press MENU to cancel. “CALIBRATING, PLEASE
WAIT” will be appear prior to automatically moving to WVAL.
WVAL
—
Press ENTER to display and edit the test weight value. Press ENTER again to move to
WSPAN.
WSPAN
—
Press ENTER and the A/D raw counts will be displayed. Press ENTER to calibrate the span or
press MENU to cancel. “CALIBRATING, PLEASE WAIT” will be appear prior to automatically
moving to WLIN.
WLIN
PT->1 — PT->5
WGT 1 allows you to display and edit the test weight value. Press ENTER to edit the value.
CAL1 allows you to calibrate and display the raw A/D value. Press TARE to perform
calibration. Press ENTER to will move to the next calibration point.
NOTE: The linearity points are optional, but must NOT duplicate zero or span. They must be
between zero and span.
REZERO
—
Press ENTER to remove an offset value from the zero and span calibrations (e.g. if hooks or
chains are being used during calibration).
NOTE: Use this parameter only after WZERO and WSPAN have been set. See Section 4.1 on
page 33 for more information about using this parameter.
Table 3-3. Calibration menu parameters
Configuration
15
3.4
Setup Menu
The setup menu allows you to configure settings for the scale, features, serial port settings, print format, and
digital inputs and outputs. You can also view the software and regulatory versions, and revert to default settings.
NOTE: If RANGE is displayed after a scale setup value is entered, the value is too large or small for the given parameter.
3.4.1
SCALE Submenu
Calibration can be performed in two places within the menu: the CALIBR menu shown in Figure 3-5 is an
in-depth scale setup and calibration. A “quick access” calibration is shown in Figure 4-1 on page 33.
AUDIT
CALIBR
XXXXXXX
SETUP
TEST
EXIT
T&D
BRIGHT
ACCUM
Only displayed if
turned on
from Setup menu
ID
XXXXXXX
Only displayed if
turned on
from Setup menu
CONFIG
SCALE
FEATUR
SERIAL
PFORMT
GRADS
CALIBR
FORMAT
DIGI/O
VERS
MOTBAN
OVRLOA
1.900000
1
FS+2%
10
number
number
FS+1D
number
ZTRKBN
ZRANGE
10000
0
number
number
SSTIME
FS+9D
FS
WZERO
WVAL
WSPAN
Previous A/D raw
counts are shown
Press Enter
to calibrate zero
Press Menu
to cancel
Display and edit
test weight value
Previous A/D raw
counts are shown
Press Enter
to calibrate span
Press Menu
to cancel
Calibrating, please wait
WLI N
REZERO
PRIMRY
PT–> 2
TER
KG
OFF
G
KG
Calibrating, please wait
Press Enter to
remove offset from
zero and span
calibrations
G
LB
OZ *
LB/OZ
Calibrating, please wait
PT–> 1
SEC
PT–> 3
PT–> 4
LB
LB/OZ*
OZ
OFF
LB/OZ*
UNITS
DECPNT
DSPDIV
LB
888888
1D
888880
2D
8.88888
5D
PT–> 5
Same as PT->1
WGT 1
OZ
CAL1
KG
G
LB/OZ
*
88.8888
888.888
8888.88
88888.8
SMPRAT
DFLTR1
DFLTR2
DFLTR3
DFSENS
DFTHRH
TAREFN
ACCUM
VISIBL
THRESH
0
30HZ
4
4
4
2OUT
NONE
BOTH
GO
OFF
ON
7.5HZ
8
8
8
4OUT
2D
NOTARE
DELAY
ON
OFF
15HZ
16
16
16
8OUT
5D
PBTARE
60HZ
32
32
32
16OUT
10D
KEYED
120HZ
64
64
64
32OUT
20D
240HZ
128
128
128
64OUT
50D
480HZ
256
256
256
128OUT
100D
960HZ
1
1
1
200D
2
2
2
250D
* Not legal for trade
Figure 3-5. Setup menu: Scale submenu
16
PWRUPM
CW-90/90X Installation Manual
SCALE Menu
Parameter
Choices
Description
Level 3 submenus
CALIBR
GRADS
WZERO
WVAL
WSPAN
WLIN
REZERO
See Section 3.3 on page 14 for descriptions, and see Section 4.0 on page 33 for
calibration procedures.
10000
1–100000
Specifies the number of full scale graduations.
Calibration can be performed in two places within the menu: the CALIBR menu shown in
Figure 3-5 is an in-depth scale setup and calibration. A “quick access” calibration is shown
in Figure 4-1 on page 33.
The value entered must be in the range 1–100000 and should be consistent with legal
requirements and environmental limits on system resolution.
To calculate GRADS, use the formula: GRADS = Capacity / Display Divisions.
Display divisions are specified under the FORMAT submenu.
NOTE: If RANGE is displayed after the value is entered, the value is too large or small for the
given parameter.
FORMAT
PRIMRY
SEC
TER
Select your primary, secondary, and tertiary units of measure. Sub-choices include lb, kg,
oz, and g. Secondary and tertiary units can also be set to lb/oz (lb/oz is not legal for trade),
or off.
ZTRKBN
0
number
Automatically zeroes the scale when within the range specified, as long as the input is
within the ZRANGE and scale is at standstill. Specify the zero tracking band in ± display
divisions. Maximum legal value varies depending on local regulations.
NOTE: For scales using linear calibration, do not set the zero tracking band to a value
greater than that specified for the first linearization point.
ZRANGE
1.900000
number
Selects the range within which the scale can be zeroed. The 1.900000 default value is ±
1.9% around the calibrated zero point, for a total range of 3.8%. Indicator must be at
standstill to zero the scale. Use the default value for legal-for-trade applications.
MOTBAN
1
number
Sets the level, in display divisions, at which scale motion is detected. If motion is not
detected for 1 second or more, the standstill symbol lights. Some operations, including
print, tare, and zero, require the scale to be at standstill. Maximum legal value varies
depending on local regulations.
If this parameter is set to 0 the standstill annunciator does not light; operations normally
requiring standstill (zero, tare, print) are performed regardless of scale motion. If 0 is
selected, ZTRKBND must also be set to 0.
OVRLOA
FS+2%
FS+1D
FS+9D
FS
Overload. Determines the point at which the display blanks and an out-of-range error
message is displayed. Maximum legal value varies depending on local regulations.
SSTIME
10
number
Specifies the length of time the scale must be out of motion, in 0.1-second intervals, before
the scale is considered to be at standstill. Values greater than 10 are not recommended.
SMPRAT
30HZ
7.5HZ
15HZ
60HZ
120HZ
240HZ
480HZ
960HZ
Sample rate. Selects measurement rate, in samples per second, of the analog-to-digital
converter. Lower sample rate values provide greater signal noise immunity.
NOTE: Settings of 120Hz or above may be too fast to provide the desired stability in some
static weighing applications.
Configuration
17
SCALE Menu
Parameter
Choices
Description
DFLTR 1-3
4
8
16
32
64
128
256
1
2
Selects the digital filtering rate used to reduce the effects of mechanical vibration from the
immediate area of the scale. The overall filtering effect can be expressed by adding the
values assigned to the three filter stages:
DFLTR1 + DFLTR2 + DFLTR3
See Section 9.5 on page 67 for information on digital filtering.
DFSENS
2OUT
4OUT
8OUT
16OUT
32OUT
64OUT
128OUT
Digital filter cutout sensitivity. Specifies the number of consecutive readings that must fall
outside the filter threshold (DFTHRH parameter) before digital filtering is suspended.
DFTHRH
NONE
2D
5D
10D
20D
50D
100D
200D
250D
Digital filter cutout threshold. Specifies the filter threshold, in display divisions. When a
specified number of consecutive scale readings (DFSENS parameter) fall outside of this
threshold, digital filtering is suspended. If NONE is selected, the filter is always enabled.
TAREFN
BOTH
NOTARE
PBTARE
KEYED
Enables or disables push-button and keyed tares. Possible values are:
BOTH: Both push-button and keyed tares are enabled.
NOTARE: No tare allowed (gross mode only)
PBTARE: Push-button tares enabled
KEYED: Keyed tare enabled
PWRUPM
GO
DELAY
Power up mode. In GO mode, the indicator goes into operation immediately after a brief
power up display test.
Choices indicate the number of A/D conversions per update that are averaged to obtain the
displayed reading. A higher number gives a more accurate display by minimizing the effect of
a few noisy readings, but slows down the settling rate of the indicator.
In DELAY mode, the indicator performs a power up display test, then enters a 30-second
warm up period. If no motion is detected during the warm up period, the indicator becomes
operational when the warm up period ends; if motion is detected, the delay timer is reset
and the warm up period repeated.
ACCUM
OFF
ON
Accumulator. Specifies whether the scale accumulator is enabled. If enabled, accumulation
occurs whenever a print operation is performed. Scale must return to zero to re-arm a new
print.
VISIBL
ON
OFF
Scale visibility. Specifies whether weight data is displayed. Status annunciators, under/
accept/over lights remain on in weigh mode even if VISIBL is set to OFF.
THRESH
0
Enter a value to be used as divisions. When a value is entered, anything that would normal
require the scale to reach zero before it happens/rearms (except for LFT parameters) now
only needs to go below this value and then above it again.
NOTE: If checkweighing is used, THRESH should be less than the under value or it can
disable the digital I/O points from tripping.
18
CW-90/90X Installation Manual
SCALE Menu
Parameter
Choices
Description
Level 4 submenus
PRIMRY
UNITS
DECPNT
DSPDIV
Allows you to set the primary units, decimal point format, and display divisions.
SEC
KG
G
LB
OZ
LB/OZ
OFF
Allows you to set the secondary units.
Decimal point format and display divisions are selected automatically. Values are
kg=kilogram (default); g=gram; lb=pound; oz=ounce; lb/oz=pound/ounce; and off.
OFF
KG
G
LB
OZ
LB/OZ
Allows you to see the tertiary units.
Decimal point format and display divisions are selected automatically. Values are off
(default); kg=kilogram; g=gram; lb=pound; oz=ounce; lb/oz=pound/ounce.
NOTE: If secondary or tertiary values are changed, the stream tokens must be changed to
match in order to stream secondary or tertiary.
LB/OZ is not legal for trade.
TER
NOTE: If secondary or tertiary values are changed, the stream tokens must be changed to
match in order to stream secondary or tertiary.
WZERO
Allows you to view or change the zero calibration a/d count value.
WVAL
Allows you to view and edit the test weight value.
NOTE: If RANGE is displayed after the value is entered, the value is too large or small for the
given parameter.
Allows you to view or change the span calibration a/d count value.
WSPAN
WLIN
PT->1
PT->2
PT->3
PT->4
PT->5
REZERO
Press ENTER to display and edit test weight and calibration values for up to five linearization
points. Perform linear calibration only after WZERO and WSPAN have been set.
Removes offset from zero and span calibrations.
Level 5 submenus
UNITS
LB
OZ
KG
G
Specifies primary units for displayed and printed weight. Values are lb=pound; oz=ounce;
kg=kilogram; g=gram.
DECPNT
888888
88888.8
8888.88
888.888
888880
8.88888
88.8888
Allows you to place the decimal point position. Use the ID ( ) and TARGET ( ) keys to
place the decimal point where desired.
DSPDIV
1D
2D
5D
Display divisions. Selects the minimum division size for the primary unit’s displayed weight.
Table 3-4. Scale menu parameters
Configuration
19
3.4.2
FEATUR Submenu
AUDIT
CALIBR
XXXXXXX
SETUP
TEST
EXIT
T&D
BRIGHT
ACCUM
Only displayed if
turned on
from Setup menu
ID
XXXXXXX
Only displayed if
turned on
from Setup menu
CONFIG
SCALE
FEATUR
SERIAL
PFORMT
CHKWGH
REGION
MODE
VALSET
NEGCKW
ID
BUFFER
RANGE
KEYED
OFF
OFF
OFF
SOLID
TARGWT
PUSH
ON
ON
ON
GRAPH
BOTH
AUTO
TARG%
DIGI/O
VERS
UID
CONSC#
000000
CURVAL
RESVAL
0
0
LIGHTS
RDONLY
REGWOR
REGULA
See
INDUST
Submenu*
TIME
DECFMT
NTEP
GROSS
DOT
CANADA
BRUTTO
COMMA
DATE
INDUST
NONE
OIML
TFORMT
T SEP
12 HOUR
COLON
24 HOUR
COMMA
DFORMT
D SEP
SET
MMDDY4
SLASH
000000
DDMMY4
DASH
Y4MMDD
SEMI
Y4DDMM
SET
MMDDY2
000000
DDMMY2
Y2MMDD
Y2DDMM
STNDBY
KEYLCK
PASSWD
RECALL
0
CALIBR
SETUP
TEST
T&D
ID
ACCUM
0
0
0
0
0
0
OVER
UNDER
ZERO
UNITS
PRINT
TARE
ID
TARGET
NUMBER
UNLOCK
UNLOCK
UNLOCK
UNLOCK
UNLOCK
UNLOCK
UNLOCK
UNLOCK
UNLOCK
LOCK
LOCK
LOCK
LOCK
LOCK
LOCK
LOCK
LOCK
LOCK
*INDUST Submenu is in Section 3.4.3 on page 24.
Figure 3-6. FEATUR submenu
20
0N
OFF
CW-90/90X Installation Manual
FEATUR Menu
Parameter
Choices
Description
Level 2 submenus
CHKWGH
MODE
VALSET
NEGCKW
ID
BUFFER
LIGHTS
Selects the checkweighing mode (range, target weight, or target percent); controls how values
are set; enables/disables negative checkweighing; enables/disables IDs; turns the buffer on/
off; and sets the lights as a solid bar or graph representation. See Level 3 submenus.
REGION
REGULA
REGWRD
DECFMT
TIME
DATE
Selects regional settings. See Level 3 submenus.
UID
000000
Sets the unit ID, a string of up to 6 characters. Since it can be entered by way of the serial
port, any six ASCII characters can be used. This will be used in place of the <UID> token in a
print format. The default value is “1.”
CONSEC #
CURVAL
RESVAL
Allows sequential numbering for print operations (CURVAL is the current value and RESVAL is
the reset value). The consecutive number value is incremented following each print operation
that includes <CN> in the ticket format. When the consecutive number is reset, it is reset to
the RESVAL specified on the parameter.
PASSWD
CALIBR
SETUP
TEST
T&D
ID
ACCUM
Creates a password to access the CALIBR, SETUP, TEST, T&D, ID, and ACCUM menus.
Specify a non-zero value to restrict access to all configuration menus. Passwords can be
overridden by loading new firmware or entering 999999.
KEYLCK
OVER
UNDER
ZERO
UNITS
PRINT
TARE
ID
TARGET
NUMBER
Disables the OVER, UNDER, ZERO, UNITS, PRINT, TARE, ID, TARGET, and/or numeric
(CW-90 only) key(s). Select Lock to disable the key, and Unlock to enable the key.
STNDBY
0
Standby mode delay. Specifies the number of minutes the indicator must be inactive before
entering standby mode. Valid values are 0 (off) through 255 minutes. When in standby mode,
power is still supplied to the CPU and draws 1/2 of the current as when the display is
powered. The annunciators are still lit, but no weight is displayed. Press any key to exit
standby mode and reactivate the display.
NOTE: The buffer can store approx. 64KB of information, which is 500 transactions using a
format with 120 characters of output.
NOTE: Overriding passwords will clear configuration and calibration settings. To preserve
settings (i.e., ID information), use Revolution III software to upload your data to a PC, then
download it back to the CW-90 after the password override is performed.
The indicator enters standby mode if no key presses, serial communications, or scale motion
occur for the length of time specified in this parameter. Set to 0 to disable standby mode.
NOTE: Standby mode will not be implemented if there is weight on the scale.
Table 3-5. FEATUR submenu parameters
Configuration
21
FEATUR Menu
Parameter
Choices
Description
RECALL
ON
OFF
ON allows the Tare, Zero, and Units values to be maintained across a power cycle. Over/
Under/Target/ID values are also maintained.
OFF clears the values on a power cycle. Zero is reset to calibrated zero and Units are reset to
Primary. Over/Under/Target/ID values are reset as well.
Level 3 submenus
MODE
RANGE
TARGWT
TARG%
Sets checkweighing mode to range, target weight, or target percent. See Section 5.0 on
page 36 for more information.
VALSET
KEYED
PUSH
BOTH
RDONLY
KEYED allows the operator to digitally set the Accept band tolerance values using keypad
buttons while in Normal Weighing mode.
PUSH prohibits the operator from digitally entering values with the keypad. Requires the
operator to place actual weights on the scale, then press keypad buttons to acquire lower and
upper Accept band tolerance values.
BOTH is a combination mode that allows the operator to have the CW-90/90X acquire
Accept band tolerances from actual weights on the scale, but then gives the operator an
opportunity to digitally modify those values directly afterward.
RDONLY is a “read only” mode which allows the operator to see but not change values.
NEGCKW
OFF
ON
AUTO
Sets whether negative checkweighing mode is off, on, or is using auto-tare.
ID
OFF
ON
Turns IDs on or off. See Section 5.4 on page 40 for more information on IDs. if IDs are turned
off, the ID selection will not appear in the main menu structure.
BUFFER
OFF
ON
Turns the buffer on or off.
NOTE: The buffer can store approx. 64KB of information, which is 500 transactions using a
format with 120 characters of output.
LIGHTS
SOLID
GRAPH
Select SOLID if you want the checkweigher to display a solid light bar for over and under
weights; select GRAPH if you want it to illuminate lights in increments relative to how close the
weight is the acceptance band. See Section 1.4 on page 3 for an illustration of graph LEDs.
REGULA
NTEP
CANADA
REGULA
NONE
OIML
Regulatory mode. Specifies the regulatory agency having jurisdiction over the scale site.
•
•
•
•
•
OIML, NTEP, and CANADA modes allow a tare to be acquired at any weight greater
than zero. NONE allows tares to be acquired at any weight value.
OIML, NTEP, and CANADA modes allow a tare to be cleared only if the gross weight
is at no load. NONE allows tares to be cleared at any weight value.
NTEP and OIML modes allow a new tare to be acquired even if a tare is already
present. In CANADA mode, the previous tare must be cleared before a new tare can
be acquired.
NONE, NTEP and CANADA modes allow the scale to be zeroed in either gross or net
mode as long as the current weight is within the specified ZRANGE. In OIML mode,
the scale must be in gross mode before it can be zeroed; pressing the ZERO key in
net mode clears the tare.
INDUST provides a set of subparameters to allow customization of tare, clear, and
print functions in non-legal-for-trade scale installations. The value specified for this
parameter affects the function of the front panel TARE and ZERO keys.
REGWOR
GROSS
BRUTTO
Sets the term displayed when weighing in gross mode. Selecting BRUTTO replaces the Gross
annunciator with Brutto.
DECFMT
DOT
COMMA
Specifies whether decimal numbers are displayed using a period (DOT) or a comma.
Table 3-5. FEATUR submenu parameters
22
CW-90/90X Installation Manual
FEATUR Menu
Parameter
Choices
Description
TIME
TFORMT
TSEP
SET
Allows you to set the current time, and the time format and separator character.
DATE
DFORMT
D SEP
SET
Allows you to set the current date, and date format and date separator character.
Level 4 submenus
TFORMT
12 HOUR
24 HOUR
Sets the time format as 12-hour format or 24-hour format.
T SEP
COLON
COMMA
Sets the time separator as a colon or comma.
SET
000000
Sets the current time.
DFORMT
MMDDY4
DDMMY4
Y4MMDD
Y4DDMM
MMDDY2
DDMMY2
Y2MMDD
Y2DDMM
Sets the date format. Y4 will use a four-digit year value, such as 2009, while Y2 will use a
two-digit value, such as 09.
D SEP
SLASH
DASH
SEMI
Sets the date separator as a slash, dash, or semicolon.
SET
000000
Sets the current date.
CALIBR
SETUP
TEST
T&D
ID
ACCUM
0
Sets a password for the Calibrate, Setup, Test, T&D, ID, and Accum menu(s). Specify a
non-zero value to restrict access. Passwords can be overridden by loading new firmware or
entering 999999.
OVER
UNDER
ZERO
UNITS
PRINT
TARE
ID
TARGET
NUMBER
UNLOCK
LOCK
NOTE: Overriding passwords will clear configuration and calibration settings. To preserve
settings (i.e., ID information), use Revolution III software to your data to a PC, then load it back
to the CW-90 after the password override is performed.
Locks or unlocks the OVER, UNDER, ZERO, UNITS, PRINT, TARE, ID, TARGET, and numeric
button(s).
Table 3-5. FEATUR submenu parameters
Configuration
23
3.4.3
FEATUR Menu, REGULA / INDUST Submenu
AUDIT
CALIBR
XXXXXXX
SETUP
TEST
EXIT
T&D
BRIGHT
ACCUM
ID
XXXXXXX
Only displayed if
turned on
from Setup menu
Only displayed if
turned on
from Setup menu
CONFIG
SCALE
FEATUR
CHKWGH
REGION
SERIAL
UID
PFORMT
DIGI/O
UID
CONSC#
CONSC#
VERS
PASSWD
REGULA
INDUST
SNPSHT
HTARE
Only displayed if INDUST is selected
from the AGENCY parameter
ZTARE
KTARE
MTARE
NTARE
CTARE
DISPLY
NO
NO
YES
REPLAC
NO
YES
SCALE
YES
YES
NO
REMOVE
YES
NO
NOTHN
PRTMOT
PRTPT
PRTHLD
HLDWGH
MOTWGH
OVRBAS
AGENCY
NO
NO
NO
NO
NO
CALIB
NTEP
YES
YES
YES
YES
YES
SCALE
CANADA
INDUST
NONE
OIML
Figure 3-7. FEATUR menu, REGACY/INDUST submenu
FEATUR Menu, REGULA / INDUST Submenu
Parameter
Choices
Description
LEVEL 4, REGULA / INDUST submenu
SNPSHT
DISPLY
SCALE
Display or Scale weight source.
HTARE
NO, YES
Allow tare in display hold.
ZTARE
NO, YES
Remove tare on ZERO.
KTARE
YES, NO
Always allow keyed tare.
MTARE
REPLAC
REMOVE
NOTHIN
Multiple tare action.
NTARE
NO, YES
Allow negative or zero tare.
CTARE
YES, NO
Allow CLEAR key to clear tare/accumulator.
PRTMOT
NO, YES
Allow print while in motion.
PRTPT
NO, YES
Add PT to keyed tare print.
PRTHLD
NO, YES
Print during display hold.
HLDWGH
NO, YES
Allow weighment during display hold.
MOTWGH
NO, YES
Allow weighment in motion.
OVRBAS
CALIB
SCALE
Zero base for overload calculation.
CALIB = Calibrate Zero
SCALE = Scale Zero
Table 3-6. REGACY / INDUST submenu parameters
24
CW-90/90X Installation Manual
KEYLCK
STNDBY
RECALL
FEATUR Menu, REGULA / INDUST Submenu
Parameter
Choices
Description
LEVEL 4, REGULA / INDUST submenu
AGENCY
NTEP
CANADA
INDUST
NONE
OIML
Selects the agency having jurisdiction over the scale site.
•
OIML, NTEP, and CANADA modes allow a tare to be acquired at any weight greater
than zero. NONE allows tares to be acquired at any weight value. A tare can be
cleared only if the gross weight is at no load. NONE allows tares to be cleared at any
weight value.
•
NTEP and OIML modes allow a new tare to be acquired even if a tare is already
present. In CANADA mode, the previous tare must be cleared before a new tare can
be acquired.
•
NONE, NTEP and CANADA modes allow the scale to be zeroed in either gross or net
mode as long as the current weight is within the specified ZRANGE. In OIML mode,
the scale must be in gross mode before it can be zeroed; pressing ZERO in net mode
clears the tare.
•
INDUST provides a set of subparameters to allow customization of tare, clear, and
print functions in non-legal-for-trade applications.
The value specified for this parameter affects the function of the front panel TARE and ZERO
keys. See Section 9.6 on page 69 for more information.
Table 3-6. REGACY / INDUST submenu parameters
Configuration
25
3.4.4
Serial, PFORMT, DIG I/O, VERS Submenus
AUDIT
CALIBR
XXXXXXX
SETUP
TEST
EXIT
T&D
ACCUM
BRIGHT
Only displayed if
turned on
from Setup menu
CONFIG
SCALE
FEATUR
See
SCALE
Submenu
See
FEATUR
Submenu
SERIAL
PFORMT
DIGIO
ID
XXXXXXX
Only displayed if
turned on
from Setup menu
VERS
SOFTWR
REG
V 1.00
LR, V.1.00
DEFALT
NO
YES
GFMT
NFMT
ACC.FMT
STRM.FM
<x><x>
<x><x>
<x><x>
<x><x>
BUF.FMT
H1
H2
<x><x>
<x><x>
<x><x>
DIO 1
DIO 3
DIO 2
DIO 4
Same as DIO 1
OFF
INPUT
OUTPUT
OVER
FUNCTN
TIMER
OVER
000000
UNDER
TARGET
ID
PRINT
ZERO
UNDER
ACCEPT
ZEROBD
TARE
UNITS
ENTER
CLEAR
DSP ACC
CLR ACC
T&D
DSP TAR
CLR TAR
KEY LCK
HOLD
CLR CN
GRSNET
PORT1
BAUD
BITS
STOP B
TERMIN
EOLDLY
DEMAND
9600
8NONE
1
CR/LF
000000
STREAM
19200
7EVEN
2
CR
WAITSS
28800
7ODD
TARGET
38400
TRIGGE
L-STAB
57600
OFF
115200
ECHO
PORT 2
PORT 3
Same as PORT 1
Same as PORT 1
ON
OFF
1200
2400
4800
Figure 3-8. Serial, PFORMT, DIG I/O, VERS submenus
26
CW-90/90X Installation Manual
TRIGGE default
is set to OFF
SETUP Menu
Parameter
Choices
Description
Level 2 submenus
SCALE
Configure scale settings. See level 3 submenus for parameter descriptions.
FEATUR
See Section on page 17
Set checkweighing options, region settings, view Unit ID, and set consecutive
numbering. See level 3 submenus for parameter descriptions.
SERIAL
PORT 1
PORT 2
PORT 3 (Option Card)
Configure communications ports. See level 3 submenus for parameter
descriptions.
PFORMT
GFMT
NFMT
ACCFMT
STRM.FM
BUF.FMT
H1
H2
Sets the print format for gross weight, net weight, accumulated weight, stream,
buffer, Header 1 and Header 2.
DIG IO
DIO 1
DIO 2
DIO 3
DIO 4
Assign digital input/output functions.
VERS
SOFTWR
REG
DEFALT
Displays the software version.
Displays the regulatory version.
Restores settings to their default values.
Level 3 submenus
PORT 1
TRIGGE
BAUD
BITS
STOP B
TERMIN
EOLDLY
ECHO
Specifies Port 1’s mechanism for triggering a transmission of data, baud rate,
bits, stop bits, termination character, end-of-line delay, and echo.See level 4
submenu for parameter descriptions.
PORT 2
TRIGGE
BAUD
BITS
STOP B
TERMIN
EOLDLY
ECHO
Specifies Port 2’s mechanism for triggering a transmission of data, baud rate,
bits, stop bits, termination character, end-of-line delay, and echo.See level 4
submenu for parameter descriptions..
PORT 3
TRIGGE
BAUD
BITS
STOP B
TERMIN
EOLDLY
ECHO
Specifies Port 3’s mechanism for triggering a transmission of data, baud rate,
bits, stop bits, termination character, end-of-line delay, and echo.See level 4
submenu for parameter descriptions.
SOFTWR
V 1.00
Displays the software version.
REG
LR,V.1.00
Displays the legally relevant version.
DEFALT
NO
YES
Resets settings to default values if YES is selected.
Table 3-7. Serial, PFORMT, DIG I/O, VERS submenu parameters
Configuration
27
SETUP Menu
Parameter
Choices
Description
Level 4 submenus
OFF
Turns the Digital input/output off.
INPUT
OVER
UNDER
TARGET
ID
PRINT
ZERO
TARE
UNITS
ENTER
CLEAR
DSP ACC
CLR ACC
T&D
DSP TAR
CLR TAR
KEY LCK
HOLD
CLR CN
GRSNET
Digital input functions.
OUTPUT
FUNCTN
OVER
UNDER
ACCEPT
ZEROBD
TIMER
Digital output functions.
TRIGGE
DEMAND
STREAM
WAITSS
TARGET
L-STAB
OFF
DEMAND will send information out of the port only when the Print key is pressed.
STREAM allows a continuous flow of information out of the port.
WAITSS prints after a stable reading is reached, then rearms as soon as it goes
back in motion.
TARGET rearms as soon as the weight goes below the threshold, and will print
when the weight goes above the threshold again. The weight must be within the
target/accept range to print.
L-STAB will print the last stable weight and is rearmed when the weight goes in
motion. The weight must be within the target/accept range to print.
BAUD
9600
19200
28800
38400
57600
115200
1200
2400
4800
Baud rate. Selects the transmission speed for the EDP or printer port.
BITS
8NONE
7EVEN
7ODD
Selects number of data bits and parity of data transmitted from the port.
STOP B
1
2
Stop bits. Sets the number of stop bits to 1 or 2.
Table 3-7. Serial, PFORMT, DIG I/O, VERS submenu parameters
28
CW-90/90X Installation Manual
SETUP Menu
Parameter
Choices
Description
TERMIN
CR/LF
CR
Termination character. Selects termination character for data sent from the EDP
or printer port.
EOLDLY
000000
End-of-line delay. Sets the delay period, in 0.1-second intervals, from when a
formatted line is terminated to the beginning of the next formatted serial output.
Value specified must be in the range 0-255, in tenths of a second (10 = 1
second).
NOTE: An EOL may be required for continuous transmission at slower baud
rates to ensure the receiving buffer is empty before another string is transmitted
ECHO
ON
OFF
This command enables or disables echoing of the serial commands sent to the
indicator.
FUNCTN
OVER
UNDER
ACCEPT
ZEROBD
Sets the digital output function.
TIMER
000000
Set the timer to 0 for output to remain on until the function state changes. Enter
a value (in 20-millisecond increments, maximum 65535) to turn the digital output
off after the specified time (even though the function state has not chagned).
Table 3-7. Serial, PFORMT, DIG I/O, VERS submenu parameters
3.5
Test Menu
AUDIT
CALIBR
XXXXXXX
SETUP
TEST
EXIT
T&D
BRIGHT
ACCUM
Only displayed if
turned on
from Setup menu
A/D
DIG I/O
COMM
WARNING...
DISCONNECT
DIGITAL I/O
BEFORE
RUNNING TEST
PORT1
PORT2
PASS
or
FAIL
PASS
or
FAIL
RAM
KEYPAD
PASS
or
FAIL
TEST
LOOP
DIO 1
DIO 2
DIO 3
DIO 4
PASS
or
FAIL
STATUS
STATUS
STATUS
STATUS
RAW
ZERO
SPAN
mV
EXCVDC
VAL
VAL
VAL
VAL
VAL
ID
XXXXXXX
Only displayed if
turned on
from Setup menu
Figure 3-9. Test menu
TEST Menu
Parameter
Choices
Description
Level 2 submenus
A/D
RAW
ZERO
SPAN
mV
EXCVDC
Gives details of current or live A/D counts as well as stored zero and span A/D
values.
Shows voltage levels for signal and excitation voltages.
Table 3-8. TEST menu parameters
Configuration
29
TEST Menu
Parameter
DIG I/O
Choices
Description
LOOP
DIO 1
DIO 2
DIO 3
DIO 4
Tests your digital I/O ports. If they are functioning, “PASS” is displayed. If they are
not functioning, “FAIL” is displayed. NOTE: Both inputs and outputs are active
low. They go to a ground state when active.
COMM
PORT1
PORT2
Performs a loopback test on the serial ports. If they are functioning, “PASS” is
displayed. If they are not functioning, “FAIL” is displayed.
RAM
TEST
Tests the unit’s memory. if it is functioning, “PASS” is displayed. If it is not
functioning, “FAIL” is displayed.
KEYPAD
TEST
Tests the unit’s individual keypad buttons by displaying the name of the key
pressed. If nothing is displayed, the key is not functioning.
Press the Menu key to exit the test.
Warning
The I/O ports become activated when the test is performed.
Make sure any equipment is disconnected prior to
performing this test to avoid it being inadvertently activated.
Level 3 submenus
RAW
VAL
Displays the live current raw A/D count.
ZERO
VAL
Displays the captured A/D Zero calibration value.
SPAN
VAL
Displays the captured A/D Span calibration value.
mV
VAL
Displays the live current millivolt signal voltage.
EXCVDC
VAL
Displays the current excitation voltage.
LOOP
TEST
Perorms a loop test on dig I/O cards.
DIO 1
DIO 2
DIO 3
DIO 4
STATUS
Displays the status of each individual digital I/O port. If set as input, the display
shows input stats IN HI or IN LO. If set as output, pressing Enter toggles the
output beween HI and LO. OUT HI or OUT LO.
OUT LO is active.
PORT1
PORT2
TEST
Performs a loopback test on serial port 1 or 2. Connect jumper TX and RX
together on port 1 or port 2 before testing.
Table 3-8. TEST menu parameters
3.6
Time and Date Menu
AUDIT
CALIBR
XXXXXXX
SETUP
TEST
EXIT
T&D
ACCUM
BRIGHT
Only displayed if
turned on
from Setup menu
TIME
DATE
SET
SET
Figure 3-10. Time and Date menu
30
CW-90/90X Installation Manual
ID
XXXXXXX
Only displayed if
turned on
from Setup menu
3.7
ACCUM Menu
In order for the ACCUM menu to appear, ON must be selected from the SETUP » CONFIG » SCALE » ACCUM
parameter (see Figure 3-5 on page 16).
AUDIT
CALIBR
XXXXXXX
SETUP
TEST
EXIT
T&D
BRIGHT
ACCUM
ID
XXXXXXX
Only displayed if
turned on
from Setup menu
Only displayed if
turned on
from Setup menu
000000
CLEAR
Figure 3-11. ACCUM menu
3.8
BRIGHT Menu
There are eight brigntness settings on the CW-90/90X (0-7). If a number greater than 7 is selected, “RANGE” will
be displayed because the number is out of range.
AUDIT
CALIBR
XXXXXXX
SETUP
TEST
EXIT
T&D
BRIGHT
ACCUM
ID
XXXXXXX
Only displayed if
turned on
from Setup menu
Only displayed if
turned on
from Setup menu
Dimmest
0
1
2
3
4
5
6
Brightest
3.9
7
ID Menu
In order for the ID menu to appear, ON must be selected from the SETUP » CONFIG » FEATUR » CHKWGH » ID menu
(see Figure 3-6 on page 20).
AUDIT
CALIBR
XXXXXXX
SETUP
TEST
EXIT
T&D
ACCUM
BRIGHT
ID
XXXXXXX
Only displayed if
turned on
from Setup menu
Only displayed if
turned on
from Setup menu
ID1
ID2 - ID50
SAME AS ID1
TARGET
VALUE
OVER
UNDER
TARE
UNITS
DESC1
Only if in
target mode
VALUE
VALUE
VALUE
OFF
DESCRIPTION
DESC2
COPYWV
CLEAR
DESCRIPTION
KG
G
LB
OZ
LB/OZ
Figure 3-12. ID menu
Configuration
31
ID Menu
Parameter
Choices
Description
Level 2 submenus
ID 1-50
TARGET (VALUE)
OVER (VALUE)
UNDER (VALUE)
TARE (VALUE)
UNITS
DESCR1 (DESCRIPTION)
DESCR2 (DESCRIPTION)
COPYWV
CLEAR
TARGET value recalled with the ID.
OVER value recalled with the ID.
UNDER value recalled with the ID.
TARE value recalled with the ID.
UNITS selects the unit of measure for the stored ID values.
DESCR1 description recalled with the ID.
DESCR2 description recalled with the ID.
COPYWV copies the working values of Target, Over, Under, Tare, Description 1
and 2 into the ID.
CLEAR clears all values and descriptions in the ID.
Table 3-9. ID menu parameters
32
CW-90/90X Installation Manual
4.0
Calibration
The CW-90/90X can be calibrated using the front panel, EDP commands, or Revolution® III.
NOTE: Calibration can be performed in two places within the menu: the CALIBR menu shown in Figure 4-1 and the SCALE
submenu shown in Figure 3-5 on page 16. The CALIBR menu shown in Figure 4-1 is a “quick access” calibration; for more
in-depth scale setup and calibration, use the menus found under SETUP»CONFIG»SCALE (see Figure 3-5 on page 16).
Calibration consists of the following steps:
• Zero calibration
• Entering the test weight value
• Span calibration
•
•
Optional five-point linearization
Optional rezero calibration for test weights
using hooks or chains.
NOTE: The CW-90/90X requires the WZERO and WSPAN points to be calibrated. The linearity points are optional, but must NOT
duplicate zero or span. During calibration, the ENTER key acts as a data entry confirmation key. It also acts as an EXECUTE key,
and accepts the value if calibration was successful.
AUDIT
CALIBR
XXXXXXX
SETUP
TEST
EXIT
T&D
ACCUM
Only displayed if
turned on
from Setup menu
WZERO
WVAL
WSPAN
Previous A/D raw
counts are shown
Press Enter
to calibrate zero
Press Menu
to cancel
Display and edit
test weight value
Previous A/D raw
counts are shown
Press Enter
to calibrate span
Press Menu
to cancel
Calibrating, please wait
PT–> 1
WLI N
BRIGHT
ID
XXXXXXX
Only displayed if
turned on
from Setup menu
REZERO
Calibrating, please wait
Press Enter to
remove offset from
zero and span
calibrations
Calibrating, please wait
PT–> 2
WGT 1
PT–> 3
PT–> 4
PT–> 5
Same as PT->1
CAL1
Figure 4-1. Calibration (CALIBR) menu
4.1
Front Panel Calibration
1. Press the MENU button, then press until the
display reads CALIBR (see Figure 4-1).
2. Press Enter or to go to the WZERO parameter.
3. Press Enter or to view the A/D count. Press
Enter Key to Calibrate WZERO.
NOTE: If do not want to calibrate zero, press Menu to exit.
4. The indicator displays CALIBRATING, PLEASE
WAIT while calibration is in progress. When
complete, you are advanced to the next
prompt (WVAL).
NOTE: To view the new A/D count, repeat Step 3, but instead
of pressing Enter while viewing the value, press Menu to exit..
5. With WVAL displayed, press Enter to display
the stored calibration weight value. Use the
procedure shown in Figure 4-2 to enter the
value of the test weights used for the span
calibration. Press Enter to store the WVAL
value and advance to WSPAN.
to
6. With WSPAN displayed, press Enter or
view the A/D count. Place test weights on the
scale equal to WVAL. Press Enter to calibrate
WSPAN.
NOTE: If do not want to calibrate span, press Menu to exit.
7. After Enter is pressed, the indicator displays
CALIBRATING, PLEASE WAIT. When complete,
you are advanced to the next prompt (WLIN).
NOTE: To view the new A/D count, navigate back to the
WSPAN, repeat Step 6; however, instead of pressing Enter
while viewing the value, press Menu to exit.
00 0 0 00
When editing numeric values, press or to change the selected digit.
Press
or
to increment or decrement the value of the selected digit.
If not already on the screen, the decimal point will flash on the far right.
To move the decimal, press Enter, then use or to move the decimal
position. Press Enter when done.
Figure 4-2. Editing procedure for numeric values
Calibration
33
8. Five-point linearization (using the WLIN
parameter) provides increased scale accuracy
by calibrating the indicator at up to five
additional points between the zero and span
calibrations.
Linearization is optional: if you choose not to
perform linearization, skip the WLIN
parameter; if linearization values have
previously been entered, these values are reset
to zero during calibration. To perform
linearization, follow the procedure below.
NOTE: The linearity points must be less than the WSPAN
point.
•
With WLIN displayed, Press to go to the
first linearization point (PT-> 1).
• Place test weights on the scale and press
Enter.
• Use the procedure shown in Figure 4-2 to
enter the actual test weight value.The
indicator will display Press Enter Key to
Calibrate WLIN.
• Press Enter to calibrate. The indicator
displays Calibrating, Please Wait while
calibration is in progress. When complete,
the A/D count for the linear calibration is
displayed. Press Enter again to advance to
the next prompt (PT-> 2).
• Repeat for up to five linearization points.
To exit the linearization parameters, press
to return to WLIN.
9. The rezero function is used to remove a
calibration offset when hooks or chains are
used to hang the test weights. If no other
apparatus was used to hang the test weights
during calibration, remove the test weights
and press to return to the CALIBR menu.
• With REZERO displayed, press Enter or
to access the rezero function.
• If hooks or chains were used during
calibration, remove these and the test
weights from the scale. The indicator will
display Press Enter Key to REZERO.
• With all weight removed, press Enter to
rezero the scale. This function adjusts the
zero and span calibration values. The
indicator displays Calibrating, Please Wait
while the zero and span calibrations are
adjusted. When complete, the adjusted A/
D count for the zero calibration is
displayed. Press Enter, then press to
return to the CALIBR menu.
10. Press or the Menu button to return to weigh
mode.
34
CW-90/90X Installation Manual
4.2
EDP Command Calibration
To calibrate the indicator using EDP commands, the
indicator EDP port must be connected to a terminal or
personal computer. See Section 2.7.1 on page 6 for
EDP port pin assignments.
Once the indicator is connected to the sending device,
do the following:
1. Place the indicator in config mode (display
must read C O N F I G - see Figure 3-5 on
page 16) and remove all weight from the scale
platform. If your test weights require hooks or
chains, place the hooks or chains on the scale
for zero calibration.
2. Send the SC.WZERO command to calibrate
zero. The indicator displays CALIBRATING,
PLEASE WAIT while calibration is in progress.
3. Place test weights on the scale and use the
SC.WVAL command to enter the test weight
value in the following format:
SC.WVAL=nnnnnn<CR>
4. Send the SC.WSPAN command to calibrate
span. The indicator displays CALIBRATING,
PLEASE WAIT while calibration is in progress.
5. Up to five linearization points can be
c a l i b r a t e d b et w e e n t h e z er o a n d sp a n
calibration values. Use the following
commands to set and calibrate a single
linearization point:
SC.WLIN.V1=nnnnn<CR>
SC.WLIN.C1<CR>
The SC.WLIN.V1 command sets the test
weight value (nnnnn) for linearization point 1.
The SC.WLIN.C1 command calibrates the
point. Repeat using the SC.WLIN.Vx and
SC.WLIN.Cx commands as required for
additional linearization points.
6. To remove an offset value, clear all weight
from the scale, including hooks or chains used
to hang test weights, then send the
SC.REZERO command. The indicator
displays CALIBRATING, PLEASE WAIT while the
zero and span calibrations are adjusted.
7. Send the SC.KUPARROW or SC.KEXIT
EDP command to return to normal mode.
4.3
Revolution® Calibration
To calibrate the indicator using Revolution, the
indicator EDP port must be connected to a PC running
the Revolution configuration utility.
1. Place the indicator in config mode (display
reads CONFIG, see Figure 3-5 on page 16) and
remove all weight from the scale platform.
2. From Revolution, select File»New.
The Select Indicator dialog box appears.
3. Select CW-90 and click OK.
4. From the Communications menu, select
Connect.
5. From the left pane, expand the Scale selection
and click the Scale button.
4.4
More About Calibration
The following topics provide additional information
about compensating for environmental factors
(Section 4.4.1) and diagnostic information for
determining expected zero and span coefficients.
4.4.1
Adjusting Final Calibration
Calibration may be affected by environmental factors
including wind, vibration, and angular loading. For
example, if the scale is calibrated with 1000 lb, a
strain test may determine that at 2000 lb the
calibration is 3 lb high. In this case, final calibration
can be adjusted by tweaking WVAL to 998.5 lb. This
adjustment provides a linear correction of 1.5 lb per
1000 lb.
To adjust the final calibration, return to the WVAL
prompt and press ENTER to show the test weight value.
Press or to adjust calibration up or down. Press
ENTER to save the value, then press
to return to the
CALIBR menu.
Figure 4-3. Scale button
6. From the Tools menu, select Calibration Wizard.
7. Click NEXT to begin the Calibration Wizard.
8. Select whether you want to perform a
standard calibration or a standard with
multi-point linearization and click NEXT.
9. In the text box, enter the test weight value be
used for span calibration.
10. Select the checkbox if you are using chains or
hooks during the calibration, then click NEXT.
11. Remove all weight from the scale and click
Click to Calibrate Zero to begin zero calibration.
If your test weights require hooks or chains,
place them on the scale for zero calibration.
12. When zero calibration is complete, the
Calibration Wizard prompts you to place test
weights on the scale. Place the test weights on
the scale, then click Click to Calibrate Span.
13. If you chose to perform linear calibration, the
Calibration Wizard now displays prompts
(1–5). Enter the weight value for Linear Point
#1, place test weights on scale and click GO.
Repeat for additional linearization points,
then click NEXT.
14. The new and old calibration settings are
displayed. To accept the new values, click
Finish. To exit and restore the old values, click
Cancel.
Calibration
35
5.0
Checkweigher Operation
The CW-90/90X can be configured for one of the three modes of operation: range, target weight, and target
percent. Selecting which operation mode is done under the CHKWGH menu, MODE submenu (Figure 5-1).
AUDIT
CALIBR
XXXXXXX
SETUP
TEST
EXIT
T&D
ACCUM
BRIGHT
Only displayed if
turned on
from Setup menu
ID
XXXXXXX
Only displayed if
turned on
from Setup menu
CONFIG
SCALE
FEATUR
SERIAL
PFORMT
DIGI/O
VERS
CHKWGH
MODE
VALSET
NEGCKW
ID
BUFFER
RANGE
KEYED
OFF
OFF
OFF
SOLID
TARGWT
PUSH
ON
ON
ON
GRAPH
BOTH
AUTO
TARG%
LIGHTS
REDOLY
If using weight on the scale to set your over/under values, select VALSET»PUSH.
If you want to manually enter your over/under values without weight on the scale, select VALSET»KEYED.
If you want to use weight on the scale to set your over/under values, but be able to edit the values captured, select
VALSET»BOTH.
Figure 5-1. CHKWGH menu
5.1
Range Mode
In Range mode, the over and under values must be set.
The Accept band is determined as the gap between these settings.
9.80
10.20
9.81-10.19
UNDER
ACCEPT
OVER
Under = 9.80
Over = 10.20
Figure 5-2. Example of Accept band determined by under/over settings in Range mode.
5.1.1
Value Set: Keyed
To manually set the over/under values with no weight on the scale:
1. Press the OVER key. The OVER light begins flashing and the value with flashing digit is shown.
2. Using the
and
keys to increment/decrement the values and the
and
keys to move between
digits, enter the desired over value. If using the CW-90, you can also use the numeric keypad to enter the
desired over value.
NOTE: To discard any changes and return to weigh mode, press the Menu button.
3. When the desired value is displayed, press Enter.
The decimal point flashes.
4. To change the position of the decimal point, use the and keys until it is in the desired position.
5. Press Enter again to accept the value and return to weigh mode.
6. Press the UNDER key. The UNDER light begins flashing and the value with flashing digit is shown.
7. Using the
and
keys to increment/decrement the values and the
and
keys to move between
digits, enter the desired under value. If using the CW-90, you can also use the numeric keypad to enter
the desired under value.
36
CW-90/90X Installation Manual
NOTE: To discard any changes and return to weigh mode, press the Menu button.
8. When the desired value is displayed, press Enter.
The decimal point flashes.
9. To change the position of the decimal point, use the and keys until it is in the desired position.
10. Press Enter again to accept the value and return to weigh mode.
5.1.2
Value Set: Push
To set the over/under values using weight on the scale:
1. Place the weight you want to be determined as “over” on the scale.
2. Press the OVER key.
3. The weight is captured and set as the over value.
The display will read “Stored” and the over light flashes.
4. Place the weight you want to be determined as “under” on the scale.
5. Press the UNDER key.
6. The weight is captured and set as the under value.
The display will read “Stored” and the under light flashes.
7. The Accept band is set as the gap between the over and under settings. See Figure 5-2 for an example.
5.2
Target Weight Mode
In Target Weight mode, the over and under values can only be set by keying in the values. The VALSET parameter
only pertains to setting the target weight value. The Accept band is determined based on a desired target weight.
8.00
13.00
8.01-12.99
UNDER
ACCEPT
Under = 2.00
Over = 3.00
Target = 10.00
OVER
Figure 5-3. Example of under/over/target settings in Target Weight mode.
5.2.1
Value Set: Keyed
1. Press the TARGET key. The Accept light begins flashing and a flashing digit is shown.
2. Using the
and
keys to increment/decrement the values and the
and
keys to move between
digits, enter the desired value. If using the CW-90, you can also use the numeric keypad to enter the
desired target weight value.
NOTE: To discard any changes and return to weigh mode, press the Menu button.
3. When the desired value is displayed, press Enter.
The decimal point flashes.
4. To change the position of the decimal point, use the and keys until it is in the desired position.
5. Press Enter again to accept the value and return to weigh mode.
6. Press the OVER key. The Over light begins flashing and a flashing digit is shown.
7. Using the
and
keys to increment/decrement the values and the
and
keys to move between
digits, enter the desired value. If using the CW-90, you can also use the numeric keypad to enter the
desired over value.
NOTE: To discard any changes and return to weigh mode, press the Menu button.
8. When the desired value is displayed, press Enter.
The decimal point flashes.
9. To change the position of the decimal point, use the and keys until it is in the desired position.
10. Press Enter again to accept the value and return to weigh mode.
Checkweigher Operation
37
11. Press the UNDER key. The Under light begins flashing and a flashing digit is shown.
12. Using the
and
keys to increment/decrement the values and the
and
keys to move between
digits, enter the desired value. If using the CW-90, you can also use the numeric keypad to enter the
desired under value.
NOTE: To discard any changes and return to weigh mode, press the Menu button.
13. When the desired value is displayed, press Enter.
The decimal point flashes.
14. To change the position of the decimal point, use the and keys until it is in the desired position.
15. Press Enter again to accept the value and return to weigh mode.
5.2.2
Value Set: Push
1. Place the weight you want to be used as the “target” on the scale.
2. Press the Target key. The Accept light flashes and the indicator displays “STORED.” The weight has been
captured and stored as the target weight.
3. Press the OVER key. The Over light begins flashing and a flashing digit is shown.
4. Using the
and
keys to increment/decrement the values and the
and
keys to move between
digits, enter the desired value. If using the CW-90, you can also use the numeric keypad to enter the
desired over value.
NOTE: To discard any changes and return to weigh mode, press the Menu button.
5. When the desired value is displayed, press Enter.
The decimal point flashes.
6. To change the position of the decimal point, use the and keys until it is in the desired position.
7. Press Enter again to accept the value and return to weigh mode.
8. Press the UNDER key. The Under light begins flashing and a flashing digit is shown.
9. Using the
and
keys to increment/decrement the values and the
and
keys to move between
digits, enter the desired value. If using the CW-90, you can also use the numeric keypad to enter the
desired under value.
NOTE: To discard any changes and return to weigh mode, press the Menu button.
10. When the desired value is displayed, press Enter.
The decimal point flashes.
11. To change the position of the decimal point, use the and keys until it is in the desired position.
12. Press Enter again to accept the value and return to weigh mode.
5.3
Target Percent Mode
In Target Percent mode, the over and under values can only be set by keying in the values (in percentages). The
VALSET parameter only pertains to setting the target weight value. The Accept band is determined based on a
percentage of the desired target weight.
NOTE: The % annunciator will be lit during target percent setup in menu mode, but not in weigh mode.
9.50
11.00
9.51-10.99
UNDER
ACCEPT
OVER
Under = 5.00 (5%)
Over = 10.00 (10%)
Target = 10.00
Figure 5-4. Example of under/over/target settings in Target Weight mode.
5.3.1
Value Set: Keyed
1. Press the TARGET key. The Accept light begins flashing and a flashing digit is shown.
2. Using the
and
keys to increment/decrement the values and the
and
keys to move between
38
CW-90/90X Installation Manual
digits, enter the desired value. If using the CW-90, you can also use the numeric keypad to enter the
desired target percent value.
NOTE: To discard any changes and return to weigh mode, press the Menu button.
3. When the desired value is displayed, press Enter.
The decimal point flashes.
4. To change the position of the decimal point, use the and keys until it is in the desired position.
5. Press Enter again to accept the value and return to weigh mode.
6. Press the OVER key. The Over light begins flashing and a flashing digit is shown.
7. Using the
and
keys to increment/decrement the values and the
and
keys to move between
digits, enter the desired value, in percent (entering 10 equals 10%). If using the CW-90, you can also use
the numeric keypad to enter the desired over value.
NOTE: To discard any changes and return to weigh mode, press the Menu button.
8. When the desired value is displayed, press Enter.
The decimal point flashes.
9. To change the position of the decimal point, use the and keys until it is in the desired position.
10. Press Enter again to accept the value and return to weigh mode.
11. Press the UNDER key. The Under light begins flashing and a flashing digit is shown.
12. Using the
and
keys to increment/decrement the values and the
and
keys to move between
digits, enter the desired value, in percent (entering 5 equals 5%). If using the CW-90, you can also use the
numeric keypad to enter the desired under value.
NOTE: To discard any changes and return to weigh mode, press the Menu button.
13. When the desired value is displayed, press Enter.
The decimal point flashes.
14. To change the position of the decimal point, use the and keys until it is in the desired position.
15. Press Enter again to accept the value and return to weigh mode.
5.3.2
Value Set: Push
1. Place the weight you want to be used as the “target percent” value on the scale.
2. Press the Target key. The Accept light flashes and the indicator displays “STORED.” The weight has been
captured and stored as the target percent value.
3. Press the OVER key. The Over light begins flashing and a flashing digit is shown.
4. Using the
and
keys to increment/decrement the values and the
and
keys to move between
digits, enter the desired value, in percent (entering 10 equals 10%). If using the CW-90, you can also use
the numeric keypad to enter the desired over value.
NOTE: To discard any changes and return to weigh mode, press the Menu button.
5. When the desired value is displayed, press Enter.
The decimal point flashes.
6. To change the position of the decimal point, use the and keys until it is in the desired position.
7. Press Enter again to accept the value and return to weigh mode.
8. Press the UNDER key. The Under light begins flashing and a flashing digit is shown.
9. Using the
and
keys to increment/decrement the values and the
and
keys to move between
digits, enter the desired value, in percent (entering 5 equals 5%). If using the CW-90, you can also use the
numeric keypad to enter the desired under value.
NOTE: To discard any changes and return to weigh mode, press the Menu button.
10. When the desired value is displayed, press Enter.
The decimal point flashes.
11. To change the position of the decimal point, use the and keys until it is in the desired position.
12. Press Enter again to accept the value and return to weigh mode.
Checkweigher Operation
39
5.4
IDs
IDs are used to save and recall previously set over/under/tare settings, descriptions, and units preferences. The
CW-90/90X has the capacity to store up to 50 individual IDs. Make sure you have IDs enabled under the
CHKWGH menu shown in Figure 5-1 on page 36 or the menu will not appear.
AUDIT
CALIBR
XXXXXXX
SETUP
TEST
EXIT
T&D
ACCUM
BRIGHT
ID
XXXXXXX
Only displayed if
turned on
from Setup menu
Only displayed if
turned on
from Setup menu
ID1
ID2 - ID50
SAME AS ID1
TARGET
VALUE
OVER
UNDER
TARE
UNITS
DESC1
Only if in
target mode
VALUE
VALUE
VALUE
OFF
DESCRIPTION
DESC2
COPYWV
CLEAR
DESCRIPTION
KG
G
LB
OZ
LB/OZ
Figure 5-5. ID menu
5.4.1
Setting an ID
1. From the ID menu, press Enter and you will be at ID1.
2. Navigate to the ID number you want to set (1-50) by using the
and
keys.
NOTE: All menus have wrap-around functionality. If you are at ID1 and want to access ID20, you can quickly do so by moving
backwards through the menu.
3. When you have reached the ID number you want to set, press Enter to select that ID.
4. If in Target mode, “TARGET” will be displayed. If mode is not set to Target, skip to Step 8. If you do not
need to adjust the value, use the and keys to move to the next parameter. To adjust the value, press
Enter and use the
and keys to increment/decrement the values and the and keys to move
between digits. If using the CW-90, you can also use the numeric keypad to enter the desired value.
NOTE: To discard any changes and return to weigh mode, press the Menu button.
5. When the desired value is displayed, press Enter.
The decimal point flashes.
6. To change the position of the decimal point, use the and keys until it is in the desired position.
7. Press Enter again to accept the value.
8. “OVER” will be displayed. If you do not need to adjust the value, use the and keys to move to the
next parameter. To adjust the value, press Enter and use the and keys to increment/decrement the
values and the and keys to move between digits. If using the CW-90, you can also use the numeric
keypad to enter the desired value.
NOTE: To discard any changes and return to weigh mode, press the Menu button.
9. When the desired value is displayed, press Enter.
The decimal point flashes.
10. To change the position of the decimal point, use the and keys until it is in the desired position.
11. Press Enter again to accept the value
12. “UNDER” will be displayed. Press Enter and use the and keys to increment/decrement the values
and the and keys to move between digits. If using the CW-90, you can also use the numeric keypad
to enter the desired value.
NOTE: To discard any changes and return to weigh mode, press the Menu button.
13. When the desired value is displayed, press Enter.
The decimal point flashes.
14. To change the position of the decimal point, use the
40
CW-90/90X Installation Manual
and
keys until it is in the desired position.
15. Press Enter again to accept the value
16. “TARE” will be displayed. Press Enter and use the and keys to increment/decrement the values and
the and keys to move between digits. If using the CW-90, you can also use the numeric keypad to
enter the desired value.
NOTE: To discard any changes and return to weigh mode, press the Menu button.
17. When the desired value is displayed, press Enter.
The decimal point flashes.
18. To change the position of the decimal point, use the and keys until it is in the desired position.
19. Press Enter again to accept the value
20. “UNITS” will be displayed. Press Enter and use the and keys to move between units (LB, OZ, LB/
OZ, OFF, KG, G).
21. When the desired unit is displayed, press Enter.
22. “DESC1” will be displayed. If you do not need to adjust the value, use the and keys to move to the
next parameter. To adjust the value, press Enter to create an ID description. A flashing placeholder is
displayed.
and
keys to increment/decrement description entry characters and the
and
keys to
23. Use the
move between placeholders.
24. When the desired description is displayed, press the Enter key to accept.
NOTE: To discard any changes and return to weigh mode, press the Menu button.
25. “DESC2” will be displayed. If you do not need to adjust the value, use the and keys to move to the
next parameter. To adjust the value, press Enter to create a secondary ID description. A flashing
placeholder is displayed.
and
keys to increment/decrement description entry characters and the
and
keys to
26. Use the
move between placeholders.
27. When the desired description is displayed, press the Enter key to accept.
NOTE: To discard any changes and return to weigh mode, press the Menu button.
28. “COPYWV” is displayed. This feature copies the current over/under/tare values, units, description 1 and
description 2 being used in normal weighing mode and saves them into the current ID number. If you do
not want to copy the working values into this ID, use the and keys to move to the next parameter.
Press the Enter key to copy the current values into the ID. The indicator will display SAVING and return
to COPYWV when complete.
5.4.2
Using a Stored ID
1. Press the ID key. The last ID being used is displayed with the leftmost digit flashing.
2. Use the and keys to increment/decrement values and the and keys to move between digits until
the desired ID value is displayed.
NOTE: If an ID does not have values assigned to it, NO ID is displayed. The ZERO key acts as a backspace on the CW-90X. Use
this key to navigate from a two-digit ID to a one-digit ID. On the CW-90, you can use the CLR or ZERO key to backspace.
3. Press Enter to start using that ID. “LOADING” is displayed and the indicator will return to weigh mode
when the ID has been loaded.
5.5
Negative Checkweighing
You can use negative checkweighing if you have an item which you want to take weight away from. For
example, if a product on the CW-90/90X weighs 20 pounds and you want to remove weight in 2 pound
increments, with negative checkweighing enabled, the Over value could be set to -3 and the Under value could
be set to -1. The Accept band would therefore be -2, illuminating the green LED when the desired weight is
removed from the product.
NOTES: Negative checkweighing is only operable in Range mode. The Target key is not used.
When entering Over/Under values and printing, the negative symbol is not displayed. These numbers are still treated as negative
values despite the symbol not being displayed.
COM port settings are limited to L-Stab, Demand (only if NEGCKW is set to ON rather than AUTO), and Wait SS (see Figure 3-8
on page 26).
Checkweigher Operation
41
AUDIT
CALIBR
XXXXXXX
SETUP
TEST
EXIT
T&D
BRIGHT
ACCUM
Only displayed if
turned on
from Setup menu
ID
XXXXXXX
Only displayed if
turned on
from Setup menu
CONFIG
SCALE
FEATUR
SERIAL
PFORMT
DIGI/O
VERS
CHKWGH
Select Range Mode
MODE
VALSET
NEGCKW
ID
BUFFER
RANGE
KEYED
OFF
OFF
OFF
SOLID
TARGWT
PUSH
ON
ON
ON
GRAPH
BOTH
AUTO
TARG%
REDOLY
LIGHTS
Select ON or AUTO
Figure 5-6. CHKWGH menu
To use negative checkweighing:
1. Ensure Range is selected under Mode (See Figure 5-6).
2. Under the NEGCKW parameter, select ON or AUTO.
NOTE: If ON is selected, you have to manually tare when the Accept band is reached. If AUTO is selected, it will automatically
tare when the Accept band is reached and is stable.
3. Press the OVER key.
4. Using the
and
keys to increment/decrement the values and the
and
keys to move between
digits, enter the desired over value. If using the CW-90, you can also use the numeric keypad to enter the
desired over value.
NOTE: The Over value you are entering is a negative value. However, it will appear to be a higher number than the Under value on
the display because the negative symbol is not displayed. An example of Over/Under negative checkweighing values as they
appear on the display would be Over: 3 (actually recorded as -3) and Under: 1 (actually recorded as -1).
To discard any changes and return to weigh mode, press the Menu button.
5. When the desired value is displayed, press Enter.
The decimal point flashes.
6. To change the position of the decimal point, use the and keys until it is in the desired position.
7. Press Enter again to accept the value and return to weigh mode.
8. Press the UNDER key.
9. Using the
and
keys to increment/decrement the values and the
and
keys to move between
digits, enter the desired under value. If using the CW-90, you can also use the numeric keypad to enter
the desired under value.
NOTE: The Under value you are entering is a negative value. However, it will appear to be a lower number than the Over value
because the negative symbol is not displayed. An example of Over/Under negative checkweighing values as they appear on the
display would be Over: 3 (actually recorded as -3) and Under: 1 (actually recorded -1).
To discard any changes and return to weigh mode, press the Menu button.
10. When the desired value is displayed, press Enter.
The decimal point flashes.
11. To change the position of the decimal point, use the and keys until it is in the desired position.
12. Press Enter again to accept the value and return to weigh mode.
13. Place the weight on the scale and press the TARE key to begin negative checkweighing.
14. Begin removing product from the scale until the Accept band is reached.
15. If AUTO was selected in Step 2, the weight will be tared automatically. If ON was selected, press TARE to
tare the weight.
16. Repeat Steps 14-15 as needed.
42
CW-90/90X Installation Manual
6.0
Serial Commands
The CW-90/90X can be controlled by a PC or remote
keyboard connected to an indicator serial port.
Control is provided by a set of serial commands that
can simulate front panel key press functions, display
and change setup parameters, and perform reporting
f u n c t i o n s . T h i s p r o v i d e s t he a b i l i t y t o p r i n t
configuration data or to save to your hard drive.
6.1
The Serial Command Set
The serial command set can be divided into five
groups: key press commands, reporting commands,
the RESETCONFIGURATION special function
command, parameter setting commands, and transmit
weight data commands. When a serial command is
processed, the CW-90/90X responds with the message
OK. The OK response verifies that the command was
received and has been executed. If the command is
unrecognized or cannot be executed, the CW-90/90X
responds with ??.
The following sections list the commands and
command syntax used for each of these groups.
6.1.1
Command
Function
KGROSS
Go to gross mode (pseudo key)
KNET
Go to net mode (pseudo key)
KDISPACCUM
Display ACCUM (pseudo key)
KDISPTARE
Display tare (pseudo key)
KCLR
Press the CLEAR key
KCLRCN
Reset consecutive number (pseudo key)
KCLRTAR
Clear tare from system (pseudo key)
KLEFT
In menu mode, move left in the menu
KRIGHT
In menu mode, move right in the menu
KUP
In menu mode, move up in the menu; in
normal mode, scroll up to previous
configured scale.
KDOWN
In menu mode, move down in the menu; in
normal mode, scroll down to the next
configured scale.
KSAVE
In menu mode, saves the current
configuration
KEXIT
In menu mode, saves the current
configuration then exits to normal mode
KCLRNV
In menu mode, clears non-volatile RAM
K0–K9
Press number 0 (zero) through 9
KDOT
Press the decimal point (.)
KENTER
Press the ENTER key
KLOCK
Lock specified front panel key. For
example, to lock the ZERO key, enter
KLOCK=KZERO.
KUNLOCK
Unlock specified front panel key. For
example, to unlock the PRINT key, enter
KUNLOCK=KPRINT.
Key Press Commands
Key press serial commands (see Table 6-1) simulate
pressing the keys on the front panel of the indicator.
These commands can be used in both setup and
normal (weighing) mode. Several of the commands
serve as “pseudo” keys, providing functions that are
not represented by a key on the front panel.
For example, to enter a 15-pound tare weight:
1. Type K1 and press ENTER (or RETURN).
2. Type K5 and press ENTER.
3. Type KTARE and press ENTER.
Command
Function
KDATE
Display date (pseudo key)
KMENU
Press the MENU key
KTIME
Display time (pseudo key)
KZERO
In weighing mode, press the ZERO key
KESCAPE
KUNITS
In weighing mode, press the UNITS key
KPRINT
In weighing mode, press the PRINT key
Exits the selected parameter. Returns to
weigh mode if a parameter is not selected
(functions identical to the MENU key in
menu mode)
KTARE
Press the TARE key
KOVER
Press the OVER key
KUNDER
Press the UNDER key
KID
In weighing mode, press the ID key. In
menu mode, move left in the menu. In data
entry mode, move to previous digit.
KTARGET
Press the TARGET key
KGROSSNET
In weighing mode, press the GROSS/NET
key (pseudo key)
Table 6-1. Serial Key Press Commands (Continued)
Table 6-1. Serial Key Press Commands
Serial Commands
43
6.1.2
ID Commands
Command
Function
ID.DESC1#N
(32 characters max.) (#N = ID number
referenced)
ID.DESC2#N
(32 characters max.)
ID.OVER#N
(weight value)
ID.UNDER#N
(weight value)
ID.TARE#N
(weight value)
ID.TARGET#N
(weight value)
ID.UNITS#N
(same in alternate units)
ID.SELECT#N
Selects a new ID
ID.CLEAR#N
Clears a single ID
ID.CLRALL
Clears all IDs (only if in menu mode)
ID.COPYWV#N
Copies working values to a specified ID
Table 6-2. ID Commands
6.1.3
Reporting Commands
Reporting commands send specific information to the
serial port. The commands listed in Table 6-3 can be
used in all modes.
Command
Function
DUMPALL
List all parameter values
DUMPAUDIT
List audit trail information
DUMPBUFFER
Lists buffer information
DUMPIDS
List all ID information
VERSION
Write CW-90/90X software version
P
Write current displayed weight with units
identifier. See Section 9.3.1 on page 66.
ZZ
Write current weight and annunciator
status. See Section 9.3.2 on page 66.
XE
Returns a 10-digit code representing any
error conditions currently shown on the
front panel.
Table 6-3. Reporting Commands
6.1.4
Clear and Reset Commands
The following commands can be used to clear and
reset the CW-90/90X:
RS : Reset system. Resets the indicator without
resetting the configuration.
RESETCONFIGURATION: Restores all configuration
parameters to their default values (menu mode
only). The RESETCONFIGURATION function can
also be initiated by pressing navigating to the
DEFALT parameter under the VERS menu and
selecting YES. Then press ENTER to reset the
indicator.
NOTE: All load cell calibration settings are lost when the
RESETCONFIGURATION command is run.
CLEARBUFFER:
6.1.5
Clears the buffer information.
Parameter Setting Commands
Parameter setting commands allow you to display or
change the current value for a particular configuration
parameter (Tables 6-4 through 6-9).
Current configuration parameter settings can be
displayed in all modes using the following syntax:
command<ENTER>
Most parameter values can be changed in menu mode
only.
Use the following command syntax when changing
parameter values: command=value<ENTER>, where value
is either a number or a parameter value. Use no spaces
before or after the equal (=) sign. If you type an
incorrect command, the display reads ??.
For example, to set the motion band parameter to 5
divisions, type the following:
SC.MOTBAND=5<ENTER>
For parameters with selectable values, enter the
command and equal sign followed by a question
mark: command=?<ENTER> to see a list of those values.
The indicator must be in menu mode to use this
function.
NOTE: Some parameters are valid only if other parameters or
parameter values are specified. Restrictions for front-panel
configuration also apply to serial command configuration.
44
CW-90/90X Installation Manual
Command
Description
Values
SC.GRADS
Graduations
1–100000
SC.ZTRKBND
Zero track band
0, 0–100
SC.ZRANGE
Zero range
1.900000, 0–100
SC.MOTBAND
Motion band
1, 0–100
SC.SSTIME
Standstill time
1–65535
SC.OVRLOAD
Overload
FS+2%, FS+1D, FS+9D, FS
SC.DIGFLTR1
SC.DIGFLTR2
SC.DIGFLTR3
Digital filtering
1, 2, 4, 8, 16, 32, 64, 128, 256
SC.DFSENS
Digital filter cutout sensitivity
2OUT, 4OUT, 8OUT, 16OUT, 32OUT, 64OUT, 128OUT
SC.DFTHRH
Digital filter cutout threshold
NONE, 2D, 5D, 10D, 20D, 50D, 100D, 200D, 250D
SC.SMPRAT
Sample rate
30HZ, 60HZ, 120HZ, 240HZ, 480HZ, 960HZ
SC.PWRUPMD
Power up mode
GO, DELAY
SC.TAREFN
Tare function
BOTH, NOTARE, PBTARE, KEYED
SC.PRI.DECPNT
Primary units decimal position
8.888888, 88.88888, 888.8888, 8888.888, 88888.88,
888888.8, 8888888, 8888880, 8888800
SC.PRI.DSPDIV
Primary units display divisions
1D, 2D, 5D
SC.PRI.UNITS
Primary units
lb, kg, g, oz, tn, t, gn, troyoz, troylb, lt, CUSTOM, NONE, OFF
SC.PRI.CUNITS
Primary custom units
Specify units if SC.PRI.UNITS=CUSTOM
SC.ACCUM
Accumulator enable
ON, OFF
SC.VISIBLE
Scale visibility
ON, OFF
SC.WZERO
Zero calibration
—
SC.WVAL
Test weight value
test_weight_value
SC.WSPAN
Span calibration
—
SC.WLIN.F1–
SC.WLIN.F5
Actual raw count value for linearization
points 1–5
0–16777215
SC.WLIN.V1
SC.WLIN.V5
Test weight value for linearization points
1–5
0.000001–9999999
SC.WLIN.C1–
SC.WLIN.C5
Calibrate linearization points 1–5
—
SC.LC.CD
Deadload coefficient
—
SC.LC.CW
Span coefficient
—
SC.LC.CZ
Temporary zero
—
SC.REZERO
Rezero
—
Table 6-4. SCALES Serial Commands
Command
Description
Values
EDP.BAUD#p
Port baud rate
300, 600, 1200, 2400, 4800, 9600, 19200, 28800, 38400, 57600,
115200
EDP.BITS#p
Port data bits/parity
8NONE, 7EVEN, 7ODD, 8ODD, 8EVEN
EDP.TERMIN#p
Port termination character
CR/LF, CR
EDP.STOPBITS#p
Port stop bits
2, 1
Table 6-5. SERIAL Port Serial Commands
Serial Commands
45
Command
Description
Values
EDP.ECHO#p
Port echo
ON, OFF
EDP.EOLDLY#p
Port end-of-line delay
0–255 (0.1-second intervals)
EDP.TRIGGER#x
Port trigger
DEMAND, STREAM, WAITSS, TARGET, L-STAB, OFF
STR.POS#p
Custom stream identifiers
Specify replacement text for token
STR.NEG#p
Example: STR.PRI=L
STR.PRI#p
STR.SEC#p
STR.TER#p
STR.GROSS#p
STR.NET#p
STR.TARE#p
STR.MOTION#p
STR.RANGE#p
STR.OK#p
STR.INVALID#p
For commands including “#p”, p is the serial port number.
Table 6-5. SERIAL Port Serial Commands (Continued)
Command
Description
Values
BUFFER
Turns buffer off or on
OFF, ON
MODE
Sets checkweighing mode
RANGE, TARGWT, TARG%
VALSET
Value set
KEYED, PUSH, BOTH, RDONLY
NEGCKW
Sets negative checkweighing
OFF, ON, AUTO
ID
Turns IDs off or on
OFF, ON
LIGHTS
Sets the lights display
SOLID, GRAPH
CFGPWD
Configuration password
0, 1–9999999
CONSNUM
Consecutive numbering
0–9999999
CONSTUP
Consecutive number start-up value 0–9999999
DATEFMT
Date format
MMDDYYYY, DDMMYYYY, YYYYMMDD, YYYYDDMM
DATESEP
Date separator
SLASH, DASH, SEMI
DECFMT
Decimal format
DOT, COMMA
DSPBRIGHT
Sets display intensity
0 (dimmest), 1, 2, 3, 4, 5, 6, 7 (brightest)
KYBDLK
Keyboard lock (disable keypad)
OFF, ON
REGULAT
Regulatory compliance
NONE, OIML, NTEP, CANADA, INDUST
REG.HLDWGH
Allow weighment during display
hold
NO, YES
REG.CTARE
Allow clear keyed tare
NO, YES
REG.HTARE
Allow tare in display hold
NO, YES
REG.KTARE
Always allow keyed tare
NO, YES
REG.MTARE
Multiple tare action
REPLACE, REMOVE, NOTHING
REG.NTARE
Allow negative tare
NO, YES
REG.ZTARE
Remove tare on ZERO
NO, YES
Table 6-6. FEATURE Serial Commands
46
CW-90/90X Installation Manual
Command
Description
Values
REG.MOTWGH
Allow weighment in motion
NO, YES
REG.OVRBASE
Zero base for overload calculation
CALIB ZERO, SCALE ZERO
REG.PRTMOT
Allow print while in motion
NO, YES
REG.PRINTPT
Add PT to keyed tare print
NO, YES
REG.PRTHLD
Print during display hold
NO, YES
REG.SNPSHOT
Display or Scale weight source
DISPLAY, SCALE
REGWORD
Regulatory word
GROSS, BRUTTO
SD
Set date
MMDDYY, DDMMYY, YYMMDD, or YYDDMM. Enter six-digit
date using the year-month-day order specified for the
DATEFMT parameter, using only the last two digits of the year.
ST
Set time
hhmm (enter using 24-hour format)
TIMEFMT
Time format
12HOUR, 24HOUR
TIMESEP
Time separator
COLON, COMMA
ZERONLY
Disable all keys except ZERO
OFF, ON
Table 6-6. FEATURE Serial Commands (Continued)
Command
Description
Values
GFMT.FMT
Gross demand print format string
See Section 7.0 on page 51 for information about demand print
format strings.
NFMT.FMT
Net demand print format string
ACC.FMT
Accumulator print format string
STRM.FMT
Streaming Format
BUF.FMT
Buffer Format
HDRFMT1
Header 1 Format
Enter the data you want displayed in Header 1
HDRFMT2
Header 2 Format
Enter the data you want displayed in Header 2
Table 6-7. PFORMT Serial Commands
Command
Description
Values
DIO#b
Digital input function
OFF, ZERO, NT/GRS, TARE, UNITS, PRINT,
ACCUM, TIMDATE, ESC, CLEAR, DSPTAR,
IDKEY, KEY0–KEY9, KEYDP, ENTER, NAVUP,
NAVDN, NAVLFT, NAVRGT, KBDLOC, HOLD,
CLRCN, GROSS, NET, PRIM, SEC, CLRTAR,
CLRACC, TRIGGER
DIO#b
Digital output function
OVER, UNDER, ACCEPT, ZEROBD
Digital inputs and outputs are specified by bit number
Table 6-8. DIG I/O Serial Commands
Serial Commands
47
6.1.6
Normal Mode Commands
The normal mode print commands (see Table 6-9) transmit data to the serial port on demand in either setup or
normal mode.
Command
Description
Values
CONSNUM
Set consecutive number
0–9 999 999
UID
Set unit ID
nnnnnnn
SD
Set date
MMDDYY, DDMMYY, YYMMDD, or YYDDMM. Enter
six-digit date using the year-month-day order specified
for the DATEFMT parameter, using only the last two digits
of the year.
ST
Set time
hhmm (enter using 24-hour format)
SX#p
Start serial port streaming
EX#p
Stop serial port streaming
OK or ??
The port streaming parameter (EDP.STREAM#p) for the
streaming port must be set to LFT or INDUST before
using these commands.
An EX command sent while in menu mode does not
take effect until the indicator is returned to normal
mode.
XG
Transmit gross weight in displayed units
XN
Transmit net weight in displayed units
nnnnnn UU
where nnnnnn is the weight value, UU is the units.
NOTE: You can also send XGP, XGS, XGT, XTP, etc. to
specify primary, secondary or tertiary (P.S.T.).
XT
Transmit tare weight in displayed units
XA
Transmit accululator value
RS
Reset system
Soft reset. Used to reset the indicator without resetting
the configuration to the factory defaults.
BUFFER
Buffer commands
Displays on/off status of the buffer
DUMPBUFFER
Reads the buffer
CLEARBUFFER
Clears the entire buffer
Table 6-9. Normal Mode Serial Commands
6.1.7
Unique Commands
Command
Description
EDP.PORT
Returns the port you are currently connected to
Table 6-10. Unique commands
6.2
Custom Stream Formatting
Each port can be independently configured to stream a default frame format or can be customized to stream a
user-defined format. Custom formatting is very similar to the standard print formatting described in Section 7.0
on page 51. Table 6-11 lists the format identifiers used to configure a custom stream format.
Format Identifier
Defined By
Description
<P[G | N | T]>
STR.POS#N
STR.NEG#N
Polarity. Specifies positive or negative polarity for the current or
specified (Gross/Net/Tare) weight on the source scale. Possible
values are SPACE, NONE, + (for STR.POS#n), or – (for STR.NEG#n)
<U[P | S | T]>
STR.PRI#N
STR.SEC#N
STR.TER#N
Units. Specifies primary, secondary, or tertiary units for the current or
specified weight on the source scale.
Table 6-11. Custom Stream Format Identifiers
48
CW-90/90X Installation Manual
Format Identifier
Defined By
Description
<M[G | N | T]>
STR.GROSS#N
STR.NET#N
STR.TARE#N
Mode. Specifies gross, net, or tare weight for the current or
specified weight on the source scale.
<S>
STR.MOTION#N
STR.RANGE#N
STR.OK#N
STR.INVALID#N
Status for the source scale. Default values and meanings for each
status:
STR.MOTION#n
M
In motion
STR.RANGE#n
O
Out of range
STR.OK#n
<space>
OK
STR.INVALID#n
I
Invalid
<CW>
—
Status of over/under/accept. O=Over, U=Under, A=Accept.
<B [–]n,…>
See descriptions below
Bit fields. Comma-separated sequence of bit field specifiers. Must
be exactly 8 bits. Minus sign ([–]) inverts the bit.
B0
—
Always 0
B1
—
Always 1
B2
Configuration
=1 if even parity
B3
Dynamic
=1 if MODE=NET
B4
Dynamic
=1 if COZ
B5
Dynamic
=1 if standstill
B6
Dynamic
=1 if gross negative
B7
Dynamic
=1 if out of range
B8
Dynamic
=1 if secondary/tertiary
B9
Dynamic
=1 if tare in system
B10
Dynamic
=1 if tare is keyed
B11
Dynamic
=00 if MODE=GROSS
=01 if MODE=NET
=10 if MODE=TARE
=11 (not used)
B12
Dynamic
=00 if UNITS=PRIMARY
=01 if UNITS=SECONDARY
=10 if UNITS=TERTIARY
=11 (not used)
B13
Configuration
=00 (not used)
=01 if current DSPDIV=1
=10 if current DSPDIV=2
=11 if current DSPDIV=5
B14
Configuration
=00 (not used)
=01 if primary DSPDIV=1
=10 if primary DSPDIV=2
=11 if primary DSPDIV=5
B15
Configuration
=00 (not used)
=01 if secondary DSPDIV=1
=10 if secondary DSPDIV=2
=11 if secondary DSPDIV=5
B16
Configuration
=00 (not used)
=01 if tertiary DSPDIV=1
=10 if tertiary DSPDIV=2
=11 if tertiary DSPDIV=5
Table 6-11. Custom Stream Format Identifiers
Serial Commands
49
Format Identifier
Defined By
Description
B17
Configuration
=000 if current DECPNT=8888800
=001 if current DECPNT=8888880
=010 if current DECPNT=8888888
=011 if current DECPNT=888888.8
=100 if current DECPNT=88888.88
=101 if current DECPNT=8888.888
=110 if current DECPNT=888.8888
=111 if current DECPNT=88.88888
B18
Configuration
=000 if primary DECPNT=8888800
=001 if primary DECPNT=8888880
=010 if primary DECPNT=8888888
=011 if primary DECPNT=888888.8
=100 if primary DECPNT=88888.88
=101 if primary DECPNT=8888.888
=110 if primary DECPNT=888.8888
=111 if primary DECPNT=88.88888
B19
Configuration
=000 if secondary DECPNT=8888800
=001 if secondary DECPNT=8888880
=010 if secondary DECPNT=8888888
=011 if secondary DECPNT=888888.8
=100 if secondary DECPNT=88888.88
=101 if secondary DECPNT=8888.888
=110 if secondary DECPNT=888.8888
=111 if secondary DECPNT=88.88888
B20
Configuration
=000 if tertiary DECPNT=8888800
=001 if tertiary DECPNT=8888880
=010 if tertiary DECPNT=8888888
=011 if tertiary DECPNT=888888.8
=100 if tertiary DECPNT=88888.88
=101 if tertiary DECPNT=8888.888
=110 if tertiary DECPNT=888.8888
=111 if tertiary DECPNT=88.88888
<wspec [–] [0] digit[[.]digit]>
Scale weight
Weight for the source scale. wspec is defined as follows:
wspec Indicates whether the weight is the current displayed weight
(W, w), gross (G, g), net (N, n), or tare (T, t) weight. Upper-case
letters specify right-justified weights; lower-case are left-justified.
Optional /P, /S, or /T suffixes can be added before the ending
delimiter (>) to specify weight display in primary (/P), secondary (/
S), or tertiary (/T) units.
[–] Enter a minus sign (–) to include sign for negative values.
[0] Enter a zero (0) to display leading zeroes.
digit[[.][.]digit]
The first digit indicates the field width in characters. Decimal point
only indicates floating decimal; decimal point with following digit
indicates fixed decimal with n digits to the right of the decimal.
Two consecutive decimals send the decimal point even if it falls at
the end of the transmitted weight field.
<CR>
—
Carriage return
<LF>
—
Line feed
Table 6-11. Custom Stream Format Identifiers
50
CW-90/90X Installation Manual
7.0
Print Formatting
The CW-90/90X provides seven print formats, GFMT,
NFMT, ACC.FMT, STRM.FM , BUS.FMT, HDRFMT1 and
HDRFMT2. These determine the format of the printed
output when the PRINT key is pressed or when a
KPRINT EDP command is received. The GFMT and
NFMT will print to all ports assigned as DEMAND in the
THRESH parameter, based on whether a tare is in the
indicator. The ACCFMT will print to all DEMAND ports
when the ACCUM is displayed. The SFMT will be sent
as a STREAM if THRESH is set to STREAM on any port.
The HDRFMTs must be called from another format.
Each print format can be customized to include up to
300 characters of information, such as company name
and address, on printed tickets. You can use the
indicator front panel (PFORMT menu), EDP
commands, or the Revolution ® III configuration
utility to customize the print formats.
NOTES: Print formats are limited to 300 characters.
The display will only show capital letters, press the down
arrow to view the ASCII character decimal value on the
second menu level.
7.1
Print Formatting Commands
Table 7-1 lists commands you can use to format the
gross, net and count print formats. Commands
included in the format strings must be enclosed
between < and > delimiters. Any characters outside of
the delimiters are printed as text on the ticket. Text
characters can include any ASCII character that can
be printed by the output device.
Command
Description
Command
<AD>
Date of last accumulator event
<AT>
Time of last accumulator event
<UID>
Unit ID number
<CN>
Consecutive number
<NLnn>
New line (nn = number of termination (<CR/LF>
or <CR>) characters)*
<SPnn>
Space (nn = number of spaces)*
<SU>
Toggle weight data format (formatted/
unformatted)**
<TI>
Time
<DA>
Date
<TD>
Time & Date
<H1>
Header 1
<H2>
Header 2
Gross, net, and tare weights are 9 digits in length, including
sign (10 digits with decimal point), followed by a space and a
two-digit units identifier. Total field length with units identifier
is 12 (or 13) characters.
ID and consecutive number (CN) fields are 1–6 characters in
length, as required.
* If nn is not specified, 1 is assumed. Value must be in the
range 1–99.
** After receiving an SU command, the indicator sends
unformatted data until the next SU command is received.
Unformatted data omits decimal points, leading and trailing
characters.
<G>
Gross weight in displayed units
<N>
Net weight in displayed units
<T>
Tare weight in displayed units
<A>
Accumulated weight in displayed units
<CKS>
Status of over/under/accept. O=Over,
U=Under, A=Accept
<CKOV>
Over value
<CKUV>
Under value
<CKTV>
Target value
<CKID>
Loaded ID number
<CKD1>
Description 1
<CKD2>
Description 2
<CKU>
Units
NOTES:
<CKT>
Tare
•
<AC>
Number of accumulator events (5-digit counter)
Table 7-1. Print Format Commands
Description
Table 7-1. Print Format Commands
The default GFMT and NFMT print formats use only the
new line (<NL>) command and the commands for
gross, net, and tare weights in displayed units (<G>,
<N>, and <T>). The default CW-90/90X print formats
are shown in Table 7-2:
Format
Default Format String
Sample Output
GFMT
<G> GROSS<NL>
2046.81 lb GROSS
NFMT
<G> GROSS<NL>
<T> TARE<NL>
<N> NET<NL>
4053.1 lb GROSS
15.6 lb TARE
4037.5 lb NET
Table 7-2. GFMT and NFMT Formats
•
ID numbers included in the print format string
(<UID> command) must be set using the UID
EDP command.
The 300-character limit of each print format
Print Formatting
51
string includes the output field length of the
print formatting commands, not the command
length. For example, if the indicator is
configured to show a decimal point, the <G>
command generates an output field of 13
characters: the 10-character weight value
(including decimal point), one space, and a
two-digit units identifier.
7.2
To change the format, use the GFMT or NFMT EDP
command followed by an equals sign (=) and the
modified print format string. For example, to add the
name and address of a company to the gross format,
you could send the following EDP command:
NOTE: Indicator must be placed in the config mode with
CONFIG shown on the display.
GFMT=FINE TRANSFER CO<NL>32400 WEST
HIGHWAY ROAD<NL>SMALLTOWN<NL2><G>
GROSS<NL>
Customizing Print Formats
The following sections describe procedures for
customizing the GFMT, NFMT and CFMT formats using
the EDP port, the front panel (PFORMT menu), and the
Revolution® III configuration utility.
7.2.1
A ticket printed using this format might look like the
following:
FINE TRANSFER CO
32400 WEST HIGHWAY ROAD
SMALLTOWN
Using the EDP Port
With a personal computer, terminal, or remote
keyboard attached to the CW-90/90X EDP port, you
can use the EDP command set to customize the print
format strings.
To view the current setting of a format string, type the
name of the string (GFMT or NFMT) and press ENTER.
For example, to check the current configuration of the
GFMT format, type GFMT and press ENTER . The
indicator responds by sending the current
configuration for the gross format:
1345 lb GROSS
7.2.2
GFMT=<G> GROSS<NL>
AUDIT
CALIBR
XXXXXXX
SETUP
Using the Front Panel
If you have no access to equipment for
communication through the EDP port or are working
at a site where such equipment cannot be used, you
can use the PFORMT menu (see Figure 7-1) to
customize the print formats.
Using the PFORMT menu, you can edit the print format
TEST
EXIT
T&D
ACCUM
CONFIG
SCALE
FEATUR
GFMT
SERIAL
NFMT
ACCFMT
PFORMT
SFMT
NOTE: To change the active character,
use the numeric keypad to enter the new
ASCII value and press the ENTER key.
Decrement ASCII value of active character
ID
XXXXXXX
Only displayed if
turned on
from Setup menu
DIGI/O
VERS
BUFFER
H1
Same as GFMT
Press to insert a space
before the active character
Scroll left in formatting string
BRIGHT
Only displayed if
turned on
from Setup menu
Display first 6
characters of format
Display and edit
active character and
ASCII value
Scroll right in formatting string
Increment ASCII value of active character
Delete active
character
Figure 7-1. PFORMT Menu, Showing Alphanumeric Character Entry Procedure
52
CW-90/90X Installation Manual
H2
7.2.3
Using Revolution® III
The Revolution III configuration utility provides a print formatting grid with a tool bar. The grid allows you to
construct the print format without the formatting commands (<NL> and <SP>) required by the front panel or
EDP command methods. Using Revolution III, you can type text directly into the grid, then select weight value
fields from the tool bar and place them where you want them to appear on the printed ticket.
Figure 7-2 shows an example of the Revolution III print formatting grid.
Figure 7-2. Revolution III Print Format Grid
Print Formatting
53
8.0
WLAN Installation Instructions
NOTE: Before installing this option, you must contact your IT administrator to obtain network communication protocol codes and
have a RS-232 communications cable or regular comm port cable available to run between your PC and the indicator while
installing and setting up the wireless network.
The optional Lantronix® WiPort™ (WLAN - Wireless Local Area Network) wireless networking device can be
installed inside the CW-90/90X for real-time data transmission to warehouse management systems. The
Windows®-based configuration software, DeviceInstaller™ is required for installation and setup and is available
on the CD that comes with the kit. The WLAN option can be factory installed or can be purchased separately and
installed on site.
The wireless LAN option comes in a kit containing the following items:
• Pluggable wireless board (PN 97789)
• Standoffs (PN 95356)
• Antenna (PN 98357)
• CD containing Lantronix information (PN
72763)
Figure 8-1. WLAN board
8.1
Enclosure Disassembly
The indicator enclosure must be opened to install the WLAN option card and antenna and to connect cables for
the installed option card.
Warning
Before opening the unit, ensure the power cord is disconnected from the power outlet.
1. Disconnect power to the indicator.
2. Place the indicator face-down on an antistatic work mat.
3. Remove the screws that hold the backplate to the enclosure body, then lift the backplate away from the
enclosure and set it aside.
54
CW-90/90X Installation Manual
8.2
Installing the WLAN Option Card
1.
2.
3.
4.
5.
6.
8.3
Option cards are not hot-pluggable. Disconnect power to the unit before installing the WLAN
option card.
Ensure that power has been disconnected to the indicator. Remove backplate as described in the previous
section.
Carefully align the WLAN option card onto the J5 connector on the CW-90/90X CPU board.
Press down firmly to seat the option card in the CPU board connector.
Use the standoffs provided in the option kit to secure the option card to the mounting holes on the CPU
board.
Set up the WLAN configuration parameters as explained on Section 8.6 on page 56.
Make connections to the option card as required. Use cable ties to secure loose cables inside the
enclosure. When installation and configuration is complete, reassemble the enclosure (refer to
Section 2.8 on page 7).
Mounting the Antenna
1. If the antenna is not already connected, screw it in place as shown in Figure 8-2.
Figure 8-2. Antenna installed on card
2. Place the antenna through the large cord grip, closest to the option card. It is recommended for the
antenna to extend out of the cord grip so that approximately one inch (1”) is exposed. (see Figure 8-3).
Approximately 1” of WLAN
antenna exposed
Figure 8-3. WLAN antenna
3. Tighten the cord grip.Option cards are recognized when the unit is powered on.
WLAN Installation Instructions
55
8.4
Wireless Configuration via Serial Mode
You must configure the WLAN card so that it can communicate on your network. WiPort (WLAN) is
configurable using a PC and a terminal program (like Windows XP Hyperterminal) to access the device serial
port locally. To configure the WiPort (WLAN option), connect a serial cable from the J2 connector of the
installed WLAN option card to a PC.
8.5
Jumpers
There are two configuration jumpers located on the WLAN option board. See Figure 8-4 below. These jumpers
must be set to the CFG position to configure the WLAN option.
Jumpers
Location
Figure 8-4. Jumpers location
Once the configuration jumpers are in the CFG position, continue with WLAN Card Configuration to make the
necessary settings for the WLAN option.
NOTE: Not all devices display information in the same manner and depending on your IT department’s software choice for
configuring the WLAN option, the screens displayed may be different.
If using Lantronix DeviceInstaller, you may access additional information and download the latest version from their web site at:
www.lantronix.com.
8.6
WLAN Card Configuration
1. Select the Hyperterminal program on the PC.
2. Enter a name and choose an icon for the connection, then click OK.
Figure 8-5. Hyperterminal connection description screen
56
CW-90/90X Installation Manual
3. Select a Connect To option. Select the comm port you have connected your serial cable to and click OK.
Figure 8-6. Connect To screen
4. Comm port properties must be set as shown in the following screen.
Figure 8-7. Comm Port Properties screen
The WLAN configuration port uses the following settings:
• Baud Rate: 9600
• 8 Bits
• No parity
•
•
1 Stop Bit
No Flow Control
5. Make the changes and click OK to save the changes.
6. Reset the WLAN option card by pressing the manual reset button shown in Figure 8-8, and immediately
upon release, enter three lowercase x characters (xxx) at the same time.
WLAN Installation Instructions
57
Manual Reset Button
Figure 8-8. Manual Reset Button location on WLAN option card
NOTE: The easiest way to connect is to hold down the x key on the PC’s keyboard until the manual reset button is released and
the PC screen displays the MAC address and software version as shown in Figure 9. This must be done within three seconds of
resetting the WLAN option.
Upon a successful connection, the following information is displayed.
Figure 8-9. Display Information for Setup Mode
7. To enter Setup Mode, press Enter within five seconds. Note that the connection will fail if Enter is not
pressed within the five second time limit. The configuration settings display, followed by the setup menu
options. If this happens, repeat Step 5.
8. Select an option on the menu by entering the number of the option in Your Choice? field and press Enter. In
58
CW-90/90X Installation Manual
this case, we’re setting up the WLAN options so press 4 and press Enter as shown in Figure 12.
Figure 8-10. Change Setup Screen
View the current configuration by pressing Enter from the Change Setup menu. To enter a value for a parameter,
type the value and press Enter. To confirm a current value, press Enter (without inputted parameters).
9. Enter the desired Topology for the WLAN option.
Figure 8-11. Topology Screen
The two choices are:
• 0 = Infrastructure
• 1 = AdHoc.
Select 0 for your choice and press Enter.
10. The next menu choice is Network Name as shown below.
Figure 8-12. Network Name Screen
WLAN Installation Instructions
59
Enter your wireless network name as your menu choice and press Enter. This identifies the network that the
wireless option will run on.
11. The next step is to select a level of security as shown in Figure 15.
Figure 8-13. Security Level Select Screen
Security levels include:
• 0 = None
• 1 = WEP (Equivalency Protection)
• 2 = WPA
Select 1 and press Enter.
12. The next step is to set the authentication level for the configuration as shown below.
Figure 8-14. Authentication Screen
Authentication choices are:
• 0 = open/none
• 1 = Shared
Select 0 = open/none and press Enter.
60
CW-90/90X Installation Manual
13. Select the correct encryption next. Choices are WEP64 and WEP128 as shown below. Select 1 = WEP64
as the default parameter and press Enter.
Figure 8-15. Encryption Screen
14. Next, it asks to display current key? Press N and press Enter.
Figure 8-16. Display Current Screen
Select Yes (Y) for the “display current key” option. This prompt shows the currently configured key/
passphrase.
Figure 8-17. Change Key Screen
Select the data rate and press Enter.
WLAN Installation Instructions
61
15. The screen automatically goes to end the screen which gives the choice to Save and Exit (9) and is shown
below. By selecting that choice, and pressing Enter, the WLAN parameters are saved and the screen
becomes greyed out as is shown below.
Figure 8-18. Save and Exit Screen
Once all of the data is saved, you must switch the jumpers back to the OFF position (Figure 5) to exit out of the
configuration mode.
Now you can access and view all wireless data on the PC.
8.7
Enclosure Reassembly
Once cabling is complete, position the backplate over the enclosure and reinstall the backplate screws. Use the
torque pattern shown in the indicator’s manual to prevent distorting the backplate gasket.
8.8
WiPort Wireless Specifications
Category
Description
Network Standards
IEEE 802.11b; IEEE 802.11g
Frequency Range
2.412 - 2.484 GHz
Antenna Connector
1, no diversity supported
Data Rates
1, 2, 5.5, 11Mbps (802.11b)
6, 9, 12, 18, 24, 36, 48, 54Mbps (802.11g)
Radio
Number of Selectable
Channels
Up to 14 channels. Profiles available will include USA, France, Japan,
Spain, Canada and "other" (multiple countries).
Modulations
OFDM, DSSS, DBPSK, DQPSK, CCK, 16QAM, 64QAM
Antenna Connector
1
Security
WEP 64/128, WPA-PSK, TKIP, AES end-to-end encryption
Maximum Receive Level
-10 dBm (with PER < 8%)
Receiver Sensitivity
-72 dBm for 54Mbps
-87 dBm for 11Mbps
-89 dBm for 5.5Mbps
-90 dBm for 2.0Mbps
-92 dBm for 1.0Mbps
WLAN Power and Link LED Current
Max: 4 mA
Table 8-1. WiPort Wireless Specifications
62
CW-90/90X Installation Manual
8.9
WiPort Technical Data
Category
Description
CPU, Memory
Lantronix DSTni-EX 186 CPU, 256 KB zero wait state on chip SRAM, 2048 KB flash, 16 KB Bott
ROM
Firmware
Upgradeable via TFTP and serial port
Reset Circuit
Reset In is low active. Minimum reset pulse width is 2 ms at IIL = -500 aA
Serial Interface
CMOS (Asynchronous) 3.3V-level signals
Rate is software selectable (300 bps to 921600 bps)
Serial Line Formats
7 or 8 data bits, 1-2 stop bits, parity: odd, even, none
Modem Control
DTR, DCD
Flow Control
XON/XOFF (software), CTS/RTS (hardware), none
Network Interface
Wireless 802.11b, 802.11g and 10/100 Ethernet
Protocols Supported
ARP, UDP, TCP, Telnet, ICMP, SNMP, DHCP, BOOTP, Auto IP, HTTP, SMTP, TFTP
Media Access Control
CSMA/CA with ACK
Frequency Range
2.412-2.484 GHz
Range
Up to 328 feet (100m) line of sight
Modulation Techniques
OFDM
DSSS
CCK
DQPSK
DBPSK
64 QAM
16 QAM
Transmit Output Power
14 dBm + 1.5 dBm/-1.0 dBm
Peak Supply Current at 3.3V
650 mA
Management
Internal web server, SNMP (read only)
Serial login, Telnet login
DeviceInstaller software
Security
Password protection, locking features, 64/128 bit WEP, WPA-PSK, End-to-End AES
Internal Web Server
Serves web pages
Storage capacity: 1.2 MB
Weight
29 grams
Material
Metal shell
Temperature
Operating range: -30° C to +70° C (-22° F to 158° F)
Storage range: -40° C to +85° C (-40° F to +185° F)
Warranty
2-year limited warranty
Included Software
Windows® 98/NT/2000/XP based DeviceInstaller configuration software and Windows based
Comm Port Redirector, DeviceInstaller, Web-Manager
Lantronix web site: http://www.lantronix.com/
Table 8-2. WiPort Technical Data
WLAN Installation Instructions
63
8.10 WiPort Disclaimer
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one of the following measures:
• Re-orient or relocate the receiving antenna
• Increase the separation between the equipment and the receiver
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
• Consult the dealer or an experienced radio/tv technician for help
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This device is intended only for OEM integrators. The OEM integrator should be aware of the following
important issues.
Labeling of the End Product
The label of the end product integrating this module must clearly indicate that the end product contains an FCC
approved RF module. The format of such statement could be Contains Transmitter with FCC ID: R68WIPORTG
or something similar.
RSS-GEN Sections 7.1.4 and 7.1.5 Statement for Devices with Detachable Antennas
This device has been designed to operate with the antennas listed in the certificate, and having a maximum gain
of 5 dB. Antennas not included in this list or having a gain greater than 5 dB are strictly prohibited for use with
this device. The required antenna impedance is 50 ohms.
To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the
equivalent insotropically radiated power (EIRP) is not more than that required for successful communication.
Integration Note
(a) This module is authorized under limited module approval specified to mobile host equipment. So, the antenna
must be installed such that 20 cm is maintained between the antenna and the user.
(b) The transmitter module may not be co-located with any other transmitter or antenna.
As long as the two conditions above are met, further transmission testing will not be required. However, the
OEM integrator is still responsible for testing their end product for any additional compliance requirements
required with this module installed (for example, digital device emission, PC peripheral requirements, etc).
NOTE: In the event that these conditions cannot be met (for example) certain laptop configurations, general purpose PCMCIA or
similar card, or location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID cannot
be used on the final product (including the transmitter) and obtaining a separate FCC authorization.
NOTE: Changes or modifications to this device not explicitly approved by Lantronix will void the user’s authority to operate this
device.
64
CW-90/90X Installation Manual
9.0
Appendix
9.1
Error Messages
If an error code appears on the display, use the information in Table 9-1 as a troubleshooting guide. If you cannot
clear the error, call RLWS Service for assistance.
Error Display
Description
-–-----
Over range
Solution
•
•
•
Under range
-–-----–-----–-----
•
•
•
Check load cell wiring, including sense jumpers.
Check configuration, including number of grads,
channel selection, display divisions.
Check calibration, including W ZERO and W SPAN
values.
Check for scale binding or damage.
Check for proper excitation voltage.
Call RLWS Service for assistance.
A/D out of range
CHKERR - BATTERY BACK LOST
Battery Error
Press ENTER after replacing the battery to restore
defaults to battery backed storage.
CNT-BY
Count By error
E A/D
A/D physical error
EEEROM
EEPROM physical error
EVIREE
Virgin EEPROM
EPCKSM
Parameter checksum
error
EACKSM
A/D calibration
checksum error
A/D converter requires recalibration. Call RLWS Service.
EFCKSM
Printer format
checksum error
Call RLWS Service.
ELCKSM
Load cell calibration
checksum error
Recalibrate load cells.
EIDATA
Internal RAM
checksum error
Call RLWS Service.
E REF
A/D reference error
A/D converter requires recalibration. Call RLWS Service.
ERROR
Internal program error
Check configuration. Run XE command (see Section 9.2
on page 66) to determine error type. Call RLWS Service
if unable to clear error by cycling power or if error
recoccurs.
HWFERR
Hardware error
Reboot the unit. Call RLWS Service if unable to clear
error by cycling power or if error recoccurs.
OVERFL
Overflow error
Weight value too large to be displayed.
RANGE
GRADS > 100,000
WVAL > 100,000
Only shows up in Config mode.
EEPERR
EEPROM error
Call Rice Lake Weighing Systems (RLWS) for service
VERSION UPDATED
Core has been updated
or memory has been
corrupted.
Press the ENTER key. If the message persists, call
RLWS for service.
Call Rice Lake Weighing Systems (RLWS) Service.
Use TEST menu to perform DEFLT (restore defaults)
procedure, then recalibrate load cells.
Table 9-1. CW-90/90X/CW-90/90XX Error Messages
Appendix
65
9.2
Using the XE EDP Command
9.3
Status Messages
The XE EDP command can be used to remotely query
the CW-90/90X for the error conditions shown on the
front panel. The XE command returns a 5-digit
number in the format:
Two EDP commands, P and ZZ, can be used to
provide status about the indicator. These commands
are described in the following sections.
xxxxx yyyyy
where xxxxx contains
The P EDP command returns the current displayed
weight value to the EDP port, along with the units
identifier. If the indicator is in an underrange or
overload condition, the weight value is replaced with
&&&&&& (overload) or :::::: (underrange).
a decimal representation of any
existing error conditions as described in Table 9-2.
If more than one error condition exists, the number
returned is the sum of the values representing the error
conditions. For example, if the XE command returns
the number 1040, this value represents the sum of an
A/D reference error (1024) and an A/D calibration
checksum error (16).
9.3.1
9.3.2
Using the P EDP Command
Using the ZZ EDP Command
The ZZ EDP command can be used to remotely query
which annunciators are currently displayed on the
indicator front panel. The ZZ command returns the
currently displayed weight and a decimal number
representing the LED annunciators currently lit. The
format of the returned data is:
XE Error
Code
Description
XEH Hex Value
1
VIRGERR
0x00000001
2
PARMCHKERR
0x00000002
4
LOADCHKERR
0x00000004
8
PRINTCHKERR
0x00000008
16
ENVRAMERR
0x00000010
32
ENVCRCERR
0x00000020
64
BATTERYERR
0x00000040
32768
GRAVERR
0x00008000
65536
ADPHYSICALERR
0x00010000
131072
TAREERR
0x00020000
262144
EACCOVER
0x00040000
524288
STRINGERR
0x00080000
Decimal
Value
1048576
RESERVED_PF
0x00100000
1
lb/primary units
2097152
RTCERR
0x00200000
2
kg/secondary units
4194304
MISSINGHWERR
0x00400000
4
Count
0x00800000
8
Tare entered
16777216 UNRECOVERABLEERR
0x01000000
16
Gross
0x10000 - 0x80000000
Reserved
32
Net
64
Center of zero
128
Standstill
8388608
CFGCONFLICTERR
Table 9-2. Error Codes Returned on XE Command
wwwwww uu
zzz
where wwwwww uu is the current displayed weight and
units, z z z is the annunciator status value (see
Table 9-3). If more than one annunciator is lit, the
second number returned is the sum of the values
representing the active annunciators.
Example: If the annunciator status value returned on
the ZZ command is 145, the gross, standstill, and lb
annunciators are lit. 145 represents the sum of the
values for the standstill annunciator (128), gross mode
annunciator (16), and the lb/primary units annunciator
(1).
Annunciator
Table 9-3. Status Codes Returned on the ZZ Command
66
CW-90/90X Installation Manual
9.4
Continuous Output (Stream) Format
Figure 9-1 shows the continuous output format sent to the CW-90/90X EDP or printer port when the STREAM
parameter (SERIAL menu) is set to either EDP or PRN.
<STX> <POL> <wwwwwww> <UNIT> <G/N> <S> <TERM>
ASCII 02
(decimal)
G = Gross
N = Net
Polarity:
<space> = Positive
<–> = Negative
<^> = Overload
<]> = Underrange
Weight data: 7 digits, right-justified, with
decimal point, l eading zero supression.
Overload = ^^^^^^^
Underrange = ] ] ] ] ] ] ]
Display overflow = OVERFL
L = pounds
K = kilogram
T = ton
G = grams
O = ounces
<space> = none
<CR> <LF>
or <CR>
ASCII 13, 10
(decimal)
Status:
<space> = valid
I = Invalid
M = Motion
O = Over/under range
Figure 9-1. Continuous Output Data Format
9.5
Digital Filtering
The CW-90/90X uses averaged digital filtering to reduce the effect of vibration on weight readings. Adjustable
threshold and sensitivity functions allow quick settling by suspending filter averaging, allowing the weight
reading to jump to the new value. Figure 9-2 shows the digital filter parameters on the CONFIG menu.
DFLTR1
DFLTR2
DFLTR3
DFSENS
DFTHRH
4
4
4
2OUT
NONE
8
8
8
4OUT
2D
16
16
16
8OUT
5D
32
32
32
16OUT
10D
20D
64
64
64
32OUT
128
128
128
64OUT
50D
256
256
256
128OUT
100D
1
1
1
200D
2
2
2
250D
Figure 9-2. Digital Filtering Parameters on the Configuration (CONFIG) Menu
DIGFL1= n1
DIGFL2= n2
DIGFL3= n3
n2
n3
A/D Readings
1st Stage
Filter Averages
2nd Stage
Filter Averages
1st Stage
Filter Average
2nd Stage
Filter Average
3rd Stage
Filter Average
n1
Displayed
Value
Figure 9-3. Flow Diagram for CW-90/90X Digital Filters
Appendix
67
9.5.1
DIGFLx Parameters
The first three digital filtering parameters, DFLTR1,
DFLTRL2, and DFLTR3, are configurable filter
stages that control the effect of a single A/D reading
on the displayed weight. The value assigned to each
parameter sets the number of readings received from
the preceding filter stage before averaging (see
Figure 9-3).
The overall filtering effect can be expressed by adding
the values assigned to the three filter stages:
DFLTR1 + DFLTR2 + DFLTR3
For example, if the filters are configured as
DFLTR1=4, DFLTR2=8, DFLTR3=8, the overall
f i l t e r i n g e ff e c t i s 2 0 ( 4 + 8 + 8 ) . Wi t h t h i s
configuration, each A/D reading has a 1-in-20 effect
on the displayed weight value. Setting the filters to 1
effectively disables digital filtering.
9.5.2
DFSENS and DFTHRH Parameters
The three digital filters can be used by themselves to
eliminate vibration effects, but heavy filtering also
increases settling time. The DFSENS (digital filter
sensitivity) and DFTHRH (digital filter threshold)
parameters can be used to temporarily override filter
averaging and improve settling time:
• DFSENS specifies the number of consecutive
scale readings that must fall outside the filter
threshold (DFTHRH) before digital filtering
is suspended.
• DFTHRH sets a threshold value, in display
divisions. When a specified number of
consecutive scale readings (DFSENS) fall
outside of this threshold, digital filtering is
suspended. Set DFTHRH to NONE to turn off
the filter override.
9.5.3
Setting the Digital Filter Parameters
Fine-tuning the digital filter parameters greatly
improves indicator performance in heavy-vibration
environments. Use the following procedure to
determine vibration effects on the scale and optimize
the digital filtering configuration.
1. In menu mode, set all three digital filters
(DFLTR1, DFLTRL2, DFLTR3) to 1. Set
DFTHRH to NONE. Return indicator to
normal mode.
2. Remove all weight from the scale, then watch
the indicator display to determine the
magnitude of vibration effects on the scale.
Record the weight below which all but a few
readings fall. This value is used to calculate
the DFTHRH parameter value in Step 4.
For example, if a heavy-capacity scale
produces vibration-related readings of up to
50 lb, with occasional spikes to 75 lb, record
68
CW-90/90X Installation Manual
50 lb as the threshold weight value.
3. Place the indicator in menu mode and set the
digital filters (DFLTRx) to eliminate the
vibration effects on the scale. (Leave
DFTHRH set to NONE.) Reconfigure as
necessary to find the lowest effective values
for the DFLTRx parameters.
4. With optimum values assigned to the
DFLTRx parameters, calculate the DFTHRH
parameter value by converting the weight
value recorded in Step 2 to display divisions:
threshold_weight_value / DSPDIV
In the example in Step 2, with a threshold
weight value of 50 lb and a display division
value of 5lb: 50 / 5lb = 10DD. DFTHRH
should be set to 10DD for this example.
5. Finally, set the DFSENS parameter high
enough to ignore transient peaks. Longer
transients (typically caused by lower vibration
frequencies) will cause more consecutive
out-of-band readings, so DFSENS should be
set higher to counter low frequency transients.
Reconfigure as necessary to find the lowest
effective value for the DFSENS parameter.
9.5.4
Audit Trail Support
Audit trail support provides tracking information for
configuration and calibration events. To prevent
potential misuse, all configuration and calibration
changes are counted as change events.
Use the Audit menu or Revolution III to display audit
trail information. This includes the legally relevant
(LR) version number (software version for the code
that provides audit trail information), a calibration
count and, if REGULA=NTEP, a configuration count.
The exact format of the information shown depends
on the regulatory agency specified for the REGULA
parameter (FEATUR menu).
A u d i t t r a i l i n f o r m a t i o n c a n b e p r i n te d f r o m
Revolution III or by sending the DUMPAUDIT serial
command.
9.6
Regulatory Mode Functions
The function of the front panel TARE and ZERO keys depends on the value specified for the REGULAT parameter
on the FEATURE menu. Table 9-4 describes the function of these keys for the NTEP, CANADA, OIML, and
NONE regulatory modes. TARE and ZERO key functions are configurable when the REGULAT mode is set to
INDUST (see Table 9-5 on page 69).
Front Panel Key Function
REGULAT
Parameter Value
Weight on Scale
Tare in System
TARE
ZERO
NTEP
zero or negative
no
no action
ZERO
yes
CLEAR TARE
no
TARE
positive
CANADA
zero or negative
positive
OIML
zero or negative
positive
NONE
zero or negative
positive
yes
TARE
no
no action
yes
CLEAR TARE
no
TARE
yes
no action
no
no action
ZERO
yes
CLEAR TARE
ZERO and CLEAR TARE
no
TARE
ZERO
yes
TARE
ZERO and CLEAR TARE if weight is
within ZRANGE.
No action if weight is outside of
ZRANGE
no
TARE
ZERO
yes
CLEAR TARE
ZERO
no
TARE
yes
CLEAR TARE
Table 9-4. TARE and ZERO Key Functions for REGULAT Parameter Settings
Table 9-5 lists the subparameters available when configuring a scale using INDUST mode. The table includes the
default values of the INDUST subparameters and the effective (not configurable) values used by the NTEP,
CANADA, OIML, and NONE regulatory modes.
REGULAT / INDUST Parameter
Parameter Name
SNPSHOT
Text Prompt
Display or Scale weight source
REGULAT Mode
INDUST
NTEP
CANADA
OIML
NONE
DISPLAY
DISPLAY
DISPLAY
DISPLAY
SCALE
HTARE
Allow tare in display hold
NO
NO
NO
NO
YES
ZTARE
Remove tare on ZERO
NO
NO
NO
YES
NO
KTARE
Always allow keyed tare
MTARE
Multiple tare action
YES
YES
NO
YES
YES
REPLACE
REPLACE
NOTHING
REPLACE
REMOVE
NTARE
Allow negative tare
NO
NO
NO
NO
YES
CTARE
Allow CLEAR key to clear tare/
accumulator
YES
YES
NO
NO
YES
PRTMOT
Allow print while in motion
NO
NO
NO
NO
YES
PRTPT
Add PT to keyed tare print
NO
NO
YES
YES
NO
PRTHLD
Print during display hold
NO
NO
NO
NO
YES
HLDWGH
Allow weigh during display hold
NO
NO
NO
NO
YES
MOTWGH
Allow weighment in motion
NO
NO
NO
NO
NO
OVRBASE
Zero base for overload calculation
CALIB ZERO
CALIB ZERO
CALIB ZERO SCALE ZERO CALIB ZERO
Table 9-5. REGULAT / INDUST Mode Parameters, Comparison with Effective Values of Other Modes
Appendix
69
9.7
Updating CW-90/90X Firmware
To update firmware of the CW-90/90X, you must have Revolution III installed and a .hex file on your computer.
Visit www.ricelake.com to download this free configuration software and the latest .hex file.
NOTE: If the .hex file is the same version as is currently in the indicator, the firmware update will not reset the configuration. This
is helpful if the firmware becomes corrupt and you want to reload the same firmware. However, it is always recommended that
configuration be backed up in Revolution III to avoid any data loss.
1. Unplug power to the CW-90/90X and remove the back plate.
2. Wire the serial cable to the CW-90/90X’s Port 1. Refer to Table 9-6 for cable connection settings.
DB9 Cable
CW-90/90X Connector (J2)
Pin/Color
Signal
In/Out
Description
Pin
Description
In/Out
1/Brown
DCD
In
Data Carrier Detect
NC
NA
NA
2/Red
RxD
In
Receive Data
3
Tx
Out
3/Orange
TxD
Out
Transmit Data
4
Rx
In
4/Yellow
DTR
Out
Data Terminal Ready
5
DTR
In
5/Green
GND
--------
Ground
1 or 2
Gnd
--------
6/Blue
DSR
In
Data Set Ready
NC
NA
NA
7/Purple
RTS
Out
Request to Send
6
RTS
In
8/Gray
CTS
In
Clear to Send
NC
NA
NA
9/Black
RI
In
Ring Indicator
NC
NA
NA
Table 9-6. Cable connection settings
3. Install jumpers on JP3 and JP4 as shown in Figure 9-4.
JP3 AND JP4
Location
Figure 9-4. Jumpers installed on JP3 and JP4
4. Plug in power to the CW-90/90X and press the indicator’s Power button.
5. With Revolution III open, begin a new configuration file for the CW-90/90X.
6. Click Update CW90 Firmware.
70
CW-90/90X Installation Manual
Figure 9-5. Revolution III CW-90/90X screen.
7. The Rice Lake CW90 Updater screen appears. Specify the COM port the CW-90/90X is connected to,
change the baud rate if needed, and click the ellipses (...) to browse to and select the desired .hex file.
Figure 9-6. Rice Lake CW90 Updater screen
8. Click the Program button. The update will take several moments.
9. When complete, remove the jumpers shown in Figure 9-4 on page 70 and press the Power button to
power up the indicator.
Appendix
71
9.8
Specifications
(115 VAC)
Part #
Capacity
Platform Dimensions
Column
Height
Est. Ship
Weight
105957
5 lb x 0.001 lb (2.5 x 0.0005 kg) 80 x 0.02 oz
10 in x 10 in x 4.25 in
12 in
29 lb
105958
10 lb x 0.002 lb (5 x 0.001 kg) 160 x 0.05 oz
10 in x 10 in x 4.25 in
12 in
29 lb
105959
25 lb x 0.005 lb (10 0.005 kg) 400 x 0.1 oz
10 in x 10 in x 4.25 in
12 in
29 lb
105960
25 lb x 0.005 lb (10 0.005 kg) 400 x 0.1 oz
12 in x 12 in x 4.25 in
12 in
33 lb
105961
50 lb x 0.01 lb (25 x 0.005 kg) 800 x 0.2 oz
12 in x 12 in x 4.25 in
12 in
33 lb
105962
100 lb x 0.02 lb (50 x 0.01 kg) 1600 x 0.5 oz
12 in x 12 in x 4.25 in
12 in
33 lb
Part #
Capacity
Platform Dimensions
Column
Height
Est. Ship
Weight
106123
5 lb x 0.001 lb (2.5 x 0.0005 kg) 80 x 0.02 oz
10 in x 10 in x 4.25 in
12 in
29 lb
106124
10 lb x 0.002 lb (5 x 0.001 kg) 160 x 0.05 oz
10 in x 10 in x 4.25 in
12 in
29 lb
106125
25 lb x 0.005 lb (10 0.005 kg) 400 x 0.1 oz
10 in x 10 in x 4.25 in
12 in
29 lb
(230 VAC)
106126
25 lb x 0.005 lb (10 0.005 kg) 400 x 0.1 oz
12 in x 12 in x 4.25 in
12 in
33 lb
106127
50 lb x 0.01 lb (25 x 0.005 kg) 800 x 0.2 oz
12 in x 12 in x 4.25 in
12 in
33 lb
106128
100 lb x 0.02 lb (50 x 0.01 kg) 1600 x 0.5 oz
12 in x 12 in x 4.25 in
12 in
33 lb
Table 9-7. CW-90 specifications
(115 VAC)
Part #
Capacity
Platform Dimensions
Column
Height
Est. Ship
Weight
105963
5 lb x 0.001 lb (2.5 x 0.0005 kg) 80 x 0.02 oz
10 in x 10 in x 4.25 in
12 in
29 lb
105965
10 lb x 0.002 lb (5 x 0.001 kg) 160 x 0.05 oz
10 in x 10 in x 4.25 in
12 in
29 lb
105966
25 lb x 0.005 lb (10 0.005 kg) 400 x 0.1 oz
10 in x 10 in x 4.25 in
12 in
29 lb
105967
25 lb x 0.005 lb (10 0.005 kg) 400 x 0.1 oz
12 in x 12 in x 4.25 in
12 in
33 lb
105968
50 lb x 0.01 lb (25 x 0.005 kg) 800 x 0.2 oz
12 in x 12 in x 4.25 in
12 in
33 lb
105969
100 lb x 0.02 lb (50 x 0.01 kg) 1600 x 0.5 oz
12 in x 12 in x 4.25 in
12 in
33 lb
Part #
Capacity
Platform Dimensions
Column
Height
Est. Ship
Weight
106129
5 lb x 0.001 lb (2.5 x 0.0005 kg) 80 x 0.02 oz
10 in x 10 in x 4.25 in
12 in
29 lb
106130
10 lb x 0.002 lb (5 x 0.001 kg) 160 x 0.05 oz
10 in x 10 in x 4.25 in
12 in
29 lb
106131
25 lb x 0.005 lb (10 0.005 kg) 400 x 0.1 oz
10 in x 10 in x 4.25 in
12 in
29 lb
(230 VAC)
106132
25 lb x 0.005 lb (10 0.005 kg) 400 x 0.1 oz
12 in x 12 in x 4.25 in
12 in
33 lb
106133
50 lb x 0.01 lb (25 x 0.005 kg) 800 x 0.2 oz
12 in x 12 in x 4.25 in
12 in
33 lb
106134
100 lb x 0.02 lb (50 x 0.01 kg) 1600 x 0.5 oz
12 in x 12 in x 4.25 in
12 in
33 lb
Table 9-8. CW-90X specifications
72
CW-90/90X Installation Manual
Power - AC
Power - DC
9-36 VDC DC Input
1.5 A Max
Internal short circuit protection
Enclosure Dimensions 9.5 in x 6 in x 3.12 in
24 cm x 15 cm x 8 cm
Weight
2.8 Kg (6.1 lb)
Rating/Material
UL Type 4X
Certifications and Approvals
- $0/'&
/"
0
3
$&
&/
(
4
63
&4
t
*
&
0/ 8
"
)
5
4 "/% .&
- $0/'&
/"
0
3
&/
t
(
C
$&
*
&
0/ 8
Full Scale Input Signal Up to 22.5 mV
Excitation Voltage
+5V single sided
8 x 350Ω or 16 x 700Ω load cells
Sense Amplifier
Differential amplifier with
4- and 6-wire sensing
Analog Signal
Input Range
–0.5 mV/V to +4.5 mV/V
Analog Signal
Sensitivity
0.3 μV/graduation minimum,
1.5 μV/grad recommended
Input Impedance
200 MΩ, typical
Noise (ref to input)
0.3 μV p-p with digital filters at 4-4-4
Internal Resolution
8,000,000 counts
Display Resolution
100 000 dd
Measurement Rate
Up to 60 measurements/sec
Input Sensitivity
10 nV per internal count
System Linearity
Within 0.01% of full scale
Zero Stability
150 nV/°C, maximum
Span Stability
3.5 ppm/°C, maximum
Calibration Method
Software, constants stored in
EEPROM
Common Mode
Voltage
–2.35 to +3.45 V, referred to ground
Rejection
130 dB minimum @ 50 or 60 Hz
Normal Mode
Rejection
90 dB minimum @ 50 or 60 Hz
Input Overload
± 12 V continuous, static discharge
protected
RFI Protection
Signal, excitation, and sense lines
protected by capacitor bypass
&4
Analog Specifications
Enclosure
4
63
Line Voltages
Power Consumption
Fusing
Operating Temperature –10 to +40°C (legal);
–10 to +50°C (industrial)
Storage Temperature –25 to +70°C
Humidity
0–95% relative humidity
t /"
5 *
Fusing
Environmental
115 or 230 VAC
50 or 60 Hz
1.5 A @ 115 VAC (8W)
0.75 A @ 230 VAC (8W)
2.5 A 5 x 20 mm fuse
t /"
5 *
Line Voltages
Frequency
Power Consumption
"
)
5
4 "/% .&
UL
®
US
CW-90/90X Indicator
NTEP
CoC Number 08-092
Accuracy Class III/IIIL nmax : 10 000
CW-90/90X Scale
NTEP
CoC Number 95-072A2
Accuracy Class III nmax : 5 000
(Pending)
LISTED
(Pending)
Visit www.nsf.org and search by manufacturer.
Or visit the direct link at:
http://www.nsf.org/Certified/food/
Listings.asp?CompanyName=Rice+Lake%25&
(Pending)
Measurement
Canada
Approved
Approval No. AM-5710
Serial Communications
Port 1
Port 2
Port 3
Full duplex RS-232
Full duplex RS-232
Unidirectional active 20 mA current
loop
Do not use any parts on this scale that
may contain lead.
Operator Interface
Display
LED annunciators
Keypad
6-digit LED display. 14-segment, 0.8
in (20 mm) digits
Center of zero, gross, net, tare, preset
tare; percent, kg, g, lb, oz
21-key flat membrane panel (CW-90)
Piezo membrane panel (CW-90X)
Appendix
73
CW-90/90X Limited Warranty
Rice Lake Weighing Systems (RLWS) warrants that all RLWS equipment and systems properly installed by a
Distributor or Original Equipment Manufacturer (OEM) will operate per written specifications as confirmed by
the Distributor/OEM and accepted by RLWS. All systems and components are warranted against defects in
materials and workmanship for two years.
RLWS warrants that the equipment sold hereunder will conform to the current written specifications authorized
by RLWS. RLWS warrants the equipment against faulty workmanship and defective materials. If any equipment
fails to conform to these warranties, RLWS will, at its option, repair or replace such goods returned within the
warranty period subject to the following conditions:
•
•
•
•
•
•
Upon discovery by Buyer of such nonconformity, RLWS will be given prompt written notice with a
detailed explanation of the alleged deficiencies.
Individual electronic components returned to RLWS for warranty purposes must be packaged to
prevent electrostatic discharge (ESD) damage in shipment. Packaging requirements are listed in a
publication, Protecting Your Components From Static Damage in Shipment, available from RLWS
Equipment Return Department.
Examination of such equipment by RLWS confirms that the nonconformity actually exists, and was
not caused by accident, misuse, neglect, alteration, improper installation, improper repair or
improper testing; RLWS shall be the sole judge of all alleged non-conformities.
Such equipment has not been modified, altered, or changed by any person other than RLWS or its
duly authorized repair agents.
RLWS will have a reasonable time to repair or replace the defective equipment. Buyer is responsible
for shipping charges both ways.
In no event will RLWS be responsible for travel time or on-location repairs, including assembly or
disassembly of equipment, nor will RLWS be liable for the cost of any repairs made by others.
THESE
WARRANTIES EXCLUDE ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WITHOUT
LIMITATION WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE . N EITHER
RLWS NOR DISTRIBUTOR WILL, IN ANY EVENT, BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES.
RLWS
AND BUYER AGREE THAT RLWS’S SOLE AND EXCLUSIVE LIABILITY HEREUNDER IS LIMITED TO
REPAIR OR REPLACEMENT OF SUCH GOODS. IN ACCEPTING THIS WARRANTY, THE BUYER WAIVES ANY AND
ALL OTHER CLAIMS TO WARRANTY.
SHOULD
THE SELLER BE OTHER THAN
WARRANTY CLAIMS.
RLWS,
THE BUYER AGREES TO LOOK ONLY TO THE SELLER FOR
NO TERMS, CONDITIONS, UNDERSTANDING, OR AGREEMENTS PURPORTING TO MODIFY THE TERMS OF THIS
WARRANTY SHALL HAVE ANY LEGAL EFFECT UNLESS MADE IN WRITING AND SIGNED BY A CORPORATE
OFFICER OF RLWS AND THE BUYER.
© 2009 Rice Lake Weighing Systems, Inc. Rice Lake, WI USA. All Rights Reserved.
RICE LAKE WEIGHING SYSTEMS • 230 WEST COLEMAN STREET • RICE LAKE, WISCONSIN 54868 • USA
74
CW-90/90X Installation Manual