Clay Paky C61410 Instruction manual

ENGLISH
ALEDA WASH K5
ALEDA WASH K10
ALEDA WASH K20
®
C61401
C61405
C61410
INSTRUCTION MANUAL
PR
ARY
N
I
M
ELI
INDEX
Page
Contents
2
Safety information
3
Unpacking and preparation
4
Installation and start-up
5
Control panel
7
Menu setting
14
Maintenance
21
Technical information
21
Cause and solution of problems
22
Channel functions
Congratulations on choosing a Clay Paky product!
We thank you for your custom.
Please note that this product, as all the others in the rich Clay
Paky range, has been designed and made with total quality to
ensure excellent performance and best meet your expectations
and requirements.
Carefully read this instruction manual in its entirety and keep it
safe for future reference. It is essential to know the information
and comply with the instructions given in this manual to ensure
the fitting is installed, used and serviced correctly and safely.
CLAY PAKY S.p.A. disclaims all liability for damage to the fitting
or to other property or persons deriving from installation, use and
maintenance that have not been carried out in conformity with this
instruction manual, which must always accompany the fitting.
CLAY PAKY S.p.A. reserves the right to modify the
characteristics stated in this instruction manual at any time and
without prior notice.
1
SAFETY INFORMATION
• Installation
Make sure all parts for fixing the projector are in a good state of repair.
Make sure the point of anchorage is stable before positioning the projector.
The safety chain must be properly hooked onto the fitting and secured to the framework, so that, if
the primary support system fails, the fitting falls as little as possible.
If the safety chain gets used, it needs to be replaced with a genuine spare.
LED
• Minimum distance of illuminated objects
The projector needs to be positioned so that the objects hit by the beam of light are at least 0.20
metres (8”) from the lens of the projector.
0.2
• Minimum distance from flammable materials
The projector must be positioned so that any flammable materials are at least 0.20 metres (8”) from
every point on the surface of the fitting.
• Mounting surfaces
It is permissible to mount the fitting on normally flammable surfaces.
• Maximum ambient temperature
Do not operate the fixture if the ambient temperature (Ta) exceeds 40° C (104° F).
IP20
• IP20 protection rating
The fitting is protected against penetration by solid bodies of over 12mm (0.47”) in diameter (first
digit 2), but not against dripping water, rain, splashes or jets of water (second digit 0).
• Protection against electrical shock
Connection must be made to a power supply system fitted with efficient earthing (Class I appliance
according to standard EN 60598-1).
It is, moreover, recommended to protect the supply lines of the projectors from indirect contact
and/or shorting to earth by using appropriately sized residual current devices.
• Connection to mains supply
Connection to the electricity mains must be carried out by a qualified electrical installer.
Check that the mains frequency and voltage correspond to those for which the projector is designed
as given on the electrical data label.
This label also gives the input power to which you need to refer to evaluate the maximum number
of fittings to connect to the electricity line, in order to avoid overloading.
tc 90°C
• Temperature of the external surface
The maximum temperature that can be reached on the external surface of the fitting, in a thermally
steady state, is 90°C (194°F).
• Maintenance
Before starting any maintenance work or cleaning the projector, cut off power from the mains
supply.
LiFePO4
• Battery
This product contains a rechargeable lead-acid battery. To preserve the environment, please
dispose the battery at the end of its life according to the regulation in force. Instructions on how to
remove the battery from the product are available on www.claypaky.it
The products referred to in this manual conform to the European Community Directives to which
they are subject:
• Low Voltage 2006/95/CE
• Electromagnetic Compatibility 2004/108/CE
ALEDA WASH
2
UNPACKING AND PREPARATION
1
099117
2 x 183102/802
Packing contents - Fig. 1
2
UNLOCKED
3
°
90
ALEDA WASH
°
90
PAN Mechanism Lock and Release (every 90°) - Fig. 2
°
90
°
90
LOCKED
INSTALLATION AND START-UP
4
Installing the projector - Fig. 4
The projector can be installed on the floor resting on special rubber feet, on a truss or on the ceiling or wall.
WARNING: with the exception of when the projector is positioned on the floor, the safety cable must be fitted. (Cod. 105041/003 available on request).
This must be securely fixed to the support structure of the projector and then connected to the fixing point at the centre of the base.
5
1
2
2
3
1
Connecting and disconnecting power cable - Fig. 5
ALEDA WASH
4
CONTROL PANEL
6
Mains
Connecting to the mains supply - Fig. 6
7
DMX 512
5 PIN
5
4
3
1
2
SCREEN
SIGNAL
SIGNAL
DMX 512
DMX 512
3 PIN
SIGNAL
2
SCREEN
1
3
SIGNAL
Connecting to the control signal line (DMX) - Fig. 7
Use a cable conforming to specifications EIA RS-485: 2-pole twisted, shielded, 120Ohm characteristic impedance, 22-24 AWG, low capacity. Do not use
microphone cable or other cable with characteristics differing from those specified. The end connections must be made using XLR type 3 or 5-pin male/female
connectors. A terminating plug must be inserted into the last projector with a resistance of 120Ohm (minimum 1/4 W) between terminals 2 and 3.
IMPORTANT: The wires must not make contact with each other or with the metal casing of the connectors. The casing itself must be connected to the
shield braid and to pin 1 of the connectors.
8
Fixture ID
Dmx Address
2
1
Warning Message
7.5m
Switching on the projector - Fig. 8
Press the switch. The projector starts resetting the effects. At the same time, the following information scrolls on the display:
Model
A.leda Wash
Firmware
Version X.X.X
Date - Hour
xxx (Fixture ID)
Dmx Address xxx
System errors
E: .........................
W: .........................
On conclusion of resetting in case of absence of the dmx signal, Pan and Tilt move to the “Home” position (Pan 50% - Tilt 50%). The control panel
(Fig. 8) has a display and buttons for the complete programming and management of the projector menu. The display can be in one of two conditions:
rest status and setting status. When it is in the rest status, the display shows the projector’s DMX address and the Fixture ID address (if set).
During menu setting status, after a wait time (about 30 seconds) without any key having been pressed, the display automatically returns to rest status.
It should be noted than when this condition occurs, any possible value that has been modified but not yet confirmed with the
key will be cancelled.
F
Continue
ALEDA WASH
5
➔
9
28
28
Reversal of the display - Fig. 9
To activate this function, press UP and DOWN keys simultaneously while the display is in the rest mode. This status will be memorised and
maintained even for the next time it will be switched on. To return to the initial state, repeat the operation all over again.
Setting the projector starting address
On each projector, the starting address must be set for the control signal (addresses from 1 to 512).
The address can also be set with the projector switched off.
Setting the address: see pag. 8.
Setting the projector Fixture ID
On each projector, the Fixture ID address must be set for an easy identification of the fixtures in an installation (ID from 1 to 255).
The Fixture ID address can be set with the projector switched off.
Setting the Fixture ID: see pag. 8.
B
C
Functions of the buttons - Using the menu
F
C
Confirms the displayed value, or activates the displayed function, or enters the successive
menu.
Decreases the value displayed (with auto-repetitions) or passes to the next item in the menu.
DOWN
B
Increases the value displayed (with auto-repetitions) or passes to the previous item in a menu.
D
Return to the top level.
E
Commute from units, tens, hundreds, in the "Address", "Fixture ID" and "Calibration" menù.
UP
LEFT
RIGHT
USING THE MENU:
1) Press
once – “Main Menu” appears on the display.
2) Use the UP
and DOWN
keys to select the menu to be used:
• Setup (Setup Menu): To set the setting options.
• Option (Option Menu): To set the operating options
• Informations (Informations Menu): To read the counters, software version and other information.
• Manual Control (Manual control Menu): To trigger the test and manual control functions.
• Test (Test Menu): To check the proper functionning of effects
• Advanced (Advanced Menu): Access to the "Advanced menu" is recommended for a trained technical personnel.
To enable the "Advanced" see pag.13
3) Press
to display the first item in the selected menu.
4) Use the UP
and DOWN
keys to select the MENU items.
F
F
B
C
B
C
Setting addresses and options with the projector disconnected
The projector’s DMX address, as well as other possible operating options, can also be set when the appliance is disconnected from the electricity supply.
All that is needed is to press
to momentarily activate the display and thus access the settings. Once the required operations have been carried out,
the display will switch off again after a wait time of 30 seconds.
F
ALEDA WASH
6
MENU SETTING
MAIN MENU
1
2
Set Up
Dmx
Address
3
Option
Pan / Tilt
Invert
Pan
Information
Invert
Tilt
Channel
Mode
System
Errors
Fixture
Hours
Swap
Pan-Tilt
System
Version
Fixture ID
Encoder
Pan-Tilt
Ethernet
Interface
Silent
Mode
Board
Diagnost.
Standard
Dmx
Monitor
Quiet
Option
Display
Fans
Monitor
Information
Setting
Manual
Control
Network
params
User
Preset 1
Test
User
Preset 2
User
Preset 3
Advanced
4
5
Manual
Control
Default
Preset
Reset
Channel
6
Test
Pan / Tilt
Colour
Advanced
Access code
1234
Upload
Firmware
All
Setup
Model
Calibration
Continue
ALEDA WASH
7
➔
NOTE: On grey the default options
Set Up
Dmx
Address
SET UP MENU
DMX ADDRESS
NOTE: without the DMX signal the Address (XXX) flashing
Allows you to select the DMX ADDRESS.
1) Press
- the current DMX Adress appear on the display.
2) Use the UP
and DOWN
, RIGHT
keys to plan the DMX
Address.
3) Press
to confirm the selection or LEFT
to keep current settings.
Address xxx
F
B
C
E
D
F
Channel
Mode
CHANNEL MODE
Allows you to select a channel arrangement from the two available.
1) Press
- the current settings appear on the display (Standard or
Vector).
2) Use the UP
and DOWN
keys to select one of the following
settings:
- Standard
- Shape
- Extended
3) Press
to confirm the selection or LEFT
to keep current settings.
Standard
F
Shape
B
Extended
C
F
Fixture ID
D
FIXTURE ID
Allows you to select the FIXTURE ID.
- the current Fixture ID appear on the display.
1) Press
2) Use the UP
, DOWN
, RIGHT
keys to plan the Fixture ID.
3) Press
to confirm the selection or LEFT
to keep current settings.
Value xxx
F
B
F
C
D
ETHERNET INTERFACE
It lets you set the Ethernet settings to be attributed to the projector.
1) Premere
.
2) Use the UP
and DOWN
keys to select the “Ethernet Interface”
options to set:
Ethernet
Interface
F
B
C
Control Protocol
It lets you select the “Control Protocol” Art-net to assign according to the
control unit used:
1) Press
the current setting appears on the display.
2) Use the UP
and DOWN
keys to select one of the following settings:
- Disabled
- Art-net on IP 2
- Art-net on IP 10
3) Press
to confirm the selection or LEFT
to keep the current setting.
Control
Protocol
F
B
C
F
D
Repeat on DMX
It lets you enable the transmission of the Ethernet protocol by DMX signal
to all the connected projectors.
1) Press
the current setting appears on the display.
2) Use the UP
and DOWN
keys to select one of the following settings:
- Disabled: DMX transmission disabled.
- Enabled on primary: DMX transmission enabled.
3) Press
to confirm the selection or LEFT
to keep the current setting.
Repeat on
DMX
F
B
C
F
D
Universe
It lets you assign the “Universe” number to be assigned to a series of
projectors.
1) Press
– the current Universe address appears on the display.
2) Use the UP
, DOWN
, RIGHT
keys to set the Universe
address.
3) Press
to confirm the selection or LEFT
to keep the current
setting.
Universe
F
F
ALEDA WASH
E
8
B
C
E
D
OPTIONS MENU
Option
Pan / Tilt
Invert
Pan
PAN / TILT
Invert pan
Used for reversing Pan movement.
1) Press
- the current settings appear on the display (On or Off).
2) Use the UP
and DOWN
keys to enable (On) or disable (Off)
PAN inversion.
3) Press
to confirm the selection or LEFT
to keep current
settings.
On
Off
F
B
C
F
Invert
Tilt
D
Invert tilt
Used for reversing tilt movement.
1) Press
- the current settings appear on the display (On or Off).
2) Use the UP
and DOWN
keys to enable (On) or disable (Off)
Tilt inversion.
3) Press
to confirm the selection or LEFT
to keep current
settings.
On
Off
F
B
C
F
Swap
Pan-Tilt
D
Swap Pan-Tilt
Used for swapping Pan and Tilt channels (as well as Pan fine and Tilt fine).
1) Press
- the current settings appear on the display (On or Off).
2) Use the UP
and DOWN
keys to enable (On) or disable (Off)
Pan and Tilt channel swap.
3) Press
to confirm the selection or LEFT
to keep current
settings.
On
Off
F
B
C
F
Encoder
Pan-Tilt
D
Encoder Pan-Tilt
Used for enabling the Pan / Tilt encoders.
- the current settings appear on the display (On or Off).
1) Press
2) Use the UP
and DOWN
keys to enable (On) or disable (Off)
Pan / Tilt encoders.
3) Press
to confirm the selection or LEFT
to keep current
settings.
On
Off
F
B
C
F
Silent
mode
D
SILENT MODE
It lets you select the “Silent Mode” from the two available.
1) Press
the current setting appears on the display.
2) Use the UP
and DOWN
keys to select one of the following
settings:
Standard: Maximum speed and consequently maximum effects noise
level.
Quiet: reduces the speed of some effects, thereby reducing their noise
level.
3) Press
to confirm the selection or LEFT
to keep the current
setting.
Standard
F
Quiet
B
C
F
D
DISPLAY
Used for automatically reduce brightness on the display after about 30
seconds in idle.
1) Press
- the current settings appear on the display (On or Off).
2) Use the UP
and DOWN
keys to enable (On) or disable
(Off) the decreasing of display brightness.
3) Press
to confirm the selection or LEFT
to keep current
settings.
On
Display
Off
F
F
B
C
D
Continue
ALEDA WASH
9
➔
Setting
Default
Preset
SETTING
Used to save 3 different settings of the items in the options menu and
relative submenus.
1) Press
- “Default preset” appears on the display.
2) Use the UP
and DOWN
keys to select one of the following
configurations:
- Default preset (*)
- User preset 1
- User preset 2
- User Preset 3
3) Press
- “Load preset X” appears on the display.
4) Use the UP
and DOWN
keys to select:
- Load preset X to recall a previously stored configuration.
- Save to preset X to store the current configuration.
a confirmation message (Are you sure?) appears on the display.
5) Select YES to confirm the selection or NO to keep the current setting
and return to the next higher level.
(*) DEFAULT PRESET
Used for restoring default values on all options menu items and relevant
submenus.
1) Press
, a confirmation message (Are you sure?) appears on the
display.
2) Select YES to confirm the selction or NO to keep current setting.
OPTION
DEFAULT
Invert Pan
Off
Invert Tilt
Off
Swap Pan-Tilt
Off
Encoder Pan-Tilt
On
Display
On
Reset To
Dafault
F
Go Back
User
Preset 1
Load
Preset 1
Save To
Preset 1
User
Preset 2
F
Load
Preset 2
Save To
Preset 2
User
Preset 3
Load
Preset 3
Save To
Preset 3
B
C
B
C
F
INFORMATION MENU
Information
SYSTEM ERRORS
Shows a list of warnings and messages relevant to errors occurred since
the fixtures switching-on.
1) Pressing
you are allowed to reset the SYSTEM ERRORS list.
A confirmation message (Are you sure you want to clear error list ?)
appears on the display.
2) Select YES to reset the list or NO to go back.
System
Errors
F
Fixture
Hours
FIXTURE HOURS
Used for displaying projector operating hours (total and partial).
1) Press
- Hours total and partial appears on the display.
Total counter
Counts the number of projector working life hours (from manufacture to date).
Partial counter
Counts the number of partial projector working life hours since the last
reset to date.
2) Press
to reset partial projector working hours a confirmation
message (Are you sure?) appears on the display.
3) Select YES to reset partial projectors counter or NO to keep the current
setting and return to the top menu level.
Total XXX
Partial XXX
F
Reset...
F
System
Version
ALEDA WASH
Board
CPU brd
com.dev
0: PT-3f
1: Ld - Kxx
Revis.
x.x.x
x.x
x.x
x.x
SYSTEM VERSION
Used for displaying the software and hardware version of each board
installed in the projector.
CPU brd (CPU board)
0: PT-3f (Scheda Pan / Tilt)
1: Ld - Kxx (Scheda LED)
Hw.rv.
x.x
x.x
x.x
10
Board
Diagnost.
Board
0:PT-3f
1: Ld - Kxx
Status
Good
Good
BOARD DIAGNOSTIC
Used for displaying the status error of each board installed in the projector:
0: PT-3f (Scheda Pan / Tilt)
1: Ld - Kxx (Scheda LED)
Err%
0.00
0.00
DMX MONITOR
Used for displaying the projector DMX channel level in bit (Val) and in
percentage (Perc).
Dmx
Monitor
Fans
Monitor
Fan
PwrSp
Head
FANS MONITOR
Used for displaying the speed of each fan installed in the projector:
PwrSp (ventola PSU)
Head (ventola testa)
Speed (RPM)
XXXX
XXXX
NETWORK PARAMS
Allows the "Network" parameters of the projector to be displayed or:
IP address: Internet Protocol address (two projectors must not have
the same IP address)
IP mask: 255.0.0.0
Mac address: Media Access Control: the projector’s Ethernet Address
Network
params
MANUAL CONTROL
Manual
Control
RESET
Used for resetting the projector.
1) Press
to reset the projectors, a confirmation message (Are you
sure ?) appears on the display.
2) Select YES to starting reset the fixture or NO to keep the current
setting and return to the top menu level.
No
Reset
Yes
F
CHANNEL
Used for setting channel levels from the projector control panel.
1) Press
- the first channel appears on the display.
2) Use the UP
and DOWN
keys to select the required channel:
3) Press
and use the UP
and DOWN
keys to select the
required DMX level (value between 0 and 255).
4) Press LEFT
to return to the top menu level.
Channel
F
F
B
C
B
C
D
TEST MENU
Test
TEST
Allows you to check the proper functioning of effects.
1) Press
to return to the top menu level.
2) Use the UP
and DOWN
keys to select the required test.
3) Press
to confirm the selection or LEFT
to keep current settings.
Pan-Tilt
Colour
All
F
B
F
C
D
Test sequence:
Pan - Tilt effects (Pan & Tilt)
Colour effects (CMY / CTO / Colour wheel)
All effects
Continue
ALEDA WASH
11
➔
ADVANCED MENU
Advanced
To enable the "Advanced Menu" set up the "Access code" (1234) using the
UP
, DOWN
, RIGHT
keys.
Press
- "Menu advanced" appears on the display
Code
1234
B
F
Upload
Firmware
Transfer the firmware on all
the connected fixtures ?
Are you sure ?
Yes/No
Setup
Model
Changing to a wrong model
may damage the fixture.
Are you sure ?
Yes/No
C
E
UP LOAD FIRMWARE
Allows you to transfer the firmware from 1 fixture to all the connected fixtures.
1) Press
, a confirmation message appears on the display.
2) Select YES to start the firmware loading or NO to keep the current setting and return to the top menu level
F
SETUP MODEL
Allows you to change the default model of projector.
1) Press
a confirmation message appears on the display.
2) Select YES to define the model of projector or NO to keep the current
setting and return to the top menu level.
F
CALIBRATION
Allows you to adjust effects from the control panel to obtain perfect uniformity between the projectors.
1) Press
- “channels” appears on the display.
2) Using the UP
and DOWN
keys, select the effect you wish to
regulate.
and use the RIGHT
, UP
and DOWN
buttons to
3) Press
make the adjustment by setting a value between 0 and 255.
4) Press
to confirm the selection or LEFT
to keep current settings and return to the top level.
Calibration
F
F
F
B
C
E
B
C
D
FACTORY DEFAULT
Allows you to restore default values of all channels (128).
1) Press
– a confirmation message appears on the display (Reset
calibration to factory default ?).
2) Select YES to reset calibration to factory default or NO to keep the
current setting and return to the top menu level.
F
ALEDA WASH
12
TECHNICAL INFORMATION
220
(8.66")
Power supplies available
100-240V 50/60Hz
155
(6.10")
155
(6.10")
Input power
• K20 - 750VA
• K10 - 435VA
• K5 - ???VA
245
(9.65")
374
(14.72")
Lamp
LED Osram Ostar RGBW - 15W
381
(15.00")
Motors
17 stepper motors, operating with microsteps, totally microprocessor controlled.
320
(12.60")
253
(9.96")
Cooling
• Forced ventilation with axial fans
• Die-casting aluminum, high efficiency
290
(11.42")
250
(9.84")
160
(6.30")
Inputs
DMX 512
360
(14.17")
423
(16.65")
479
(18.86")
358
(14.09")
253
(9.96")
380
(14.96")
360
(14.17")
160
(6.30")
460
(18.11")
476
(18.74")
Movable body
• Movement by means of two stepper motors, controlled by
microprocessor.
• Automatic repositioning of PAN and TILT after accidental
movement not controlled by control unit.
• Travel:
- PAN = 540°
- TILT = 252°
• Maximum speeds:
- PAN = 3.20 (Normal) / 2.90 (Fast)
- TILT = 1.89 (normal) / 1.75 (Fast)
• Resolution:
- PAN = 2.11°
- PAN FINE = 0.008°
- TILT = 0.98°
- TILT FINE = 0.004°
IP20 protection rating
• Protected against the entry of solid bodies larger than 12mm
(0.47”).
• No protection against the entry of liquids.
584
(22.99")
330
(12.99")
Working position
Functioning in any position.
395
(15.55")
CE Marking
In conformity with the European Union Low Voltage Directive
2006/95/CE and Electromagnetic compatibility Directive
2004/108/CE.
CAUSE AND SOLUTION OF PROBLEMS
THE PROJECTOR WILL NOT SWITCH ON
ELECTRONICS NON-OPERATIONAL
PROBLEMS
DEFECTIVE PROJECTION
REDUCED LUMINOSITY
POSSIBLE CAUSES
No mains supply.
LED exhausted or defective.
Signal transmission cable faulty or disconnected.
Incorrect addressing.
Fault in the electronic circuits.
Lenses or reflector broken
Dust or grease deposited.
ALEDA WASH
CHECKS AND REMEDIES
Check the power supply voltage.
Replace the LED. (See instructions).
Replace the cables.
Check addresses (see instructions).
Call an authorised technician.
Call an authorised technician.
Clean (see instructions).
13
CHANNEL FUNCTION
ALEDA WASH K5
STANDARD
CHANNEL
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
SHAPES
CHANNEL MODE
Red
Red fine
Green
Green fine
Blue
Blue fine
White
White fine
CTO
Macro colour
Strobe
Dimmer
Dimmer Fine
Pan
Pan Fine
Tilt
Tilt Fine
Function
Reset
ALEDA WASH
CHANNEL
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
EXTENDED
CHANNEL MODE
Red
Red fine
Green
Green fine
Blue
Blue fine
White
White fine
CTO
Macro colour
Strobe
Dimmer
Dimmer Fine
Pan
Pan Fine
Tilt
Tilt Fine
Function
Reset
Reserved to special shape functions
Reserved to special shape functions
Reserved to special shape functions
Reserved to special shape functions
Reserved to special shape functions
Reserved to special shape functions
Reserved to special shape functions
Reserved to special shape functions
Reserved to special shape functions
Reserved to special shape functions
14
CHANNEL
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
CHANNEL MODE
Red
Red fine
Green
Green fine
Blue
Blue fine
White
White fine
CTO
Macro colour
Strobe
Dimmer
Dimmer Fine
Pan
Pan Fine
Tilt
Tilt Fine
Function
Reset
RED LED 1
GREEN LED 1
BLUE LED 1
RED LED 2
GREEN LED 2
BLUE LED 2
RED LED 3
GREEN LED 3
BLUE LED 3
RED LED 4
GREEN LED 4
BLUE LED 4
RED LED 5
GREEN LED 5
BLUE LED 5
RED LED 6
GREEN LED 6
BLUE LED 6
RED LED 7
GREEN LED 7
BLUE LED 7
(If RED "channel 1" to 0)
(If GREEN "channel 2" to 0)
(If BLUE "channel 3" to 0)
(If RED "channel 1" to 0)
(If GREEN "channel 2" to 0)
(If BLUE "channel 3" to 0)
(If RED "channel 1" to 0)
(If GREEN "channel 2" to 0)
(If BLUE "channel 3" to 0)
(If RED "channel 1" to 0)
(If GREEN "channel 2" to 0)
(If BLUE "channel 3" to 0)
(If RED "channel 1" to 0)
(If GREEN "channel 2" to 0)
(If BLUE "channel 3" to 0)
(If RED "channel 1" to 0)
(If GREEN "channel 2" to 0)
(If BLUE "channel 3" to 0)
(If RED "channel 1" to 0)
(If GREEN "channel 2" to 0)
(If BLUE "channel 3" to 0)
ALEDA WASH K10
STANDARD
CHANNEL
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
EXTENDED
CHANNEL MODE
Red
Red fine
Green
Green fine
Blue
Blue fine
White
White fine
CTO
Macro colour
Strobe
Dimmer
Dimmer Fine
Pan
Pan Fine
Tilt
Tilt Fine
Function
Reset
Zoom
SHAPES
CHANNEL
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
CHANNEL MODE
Red
Red fine
Green
Green fine
Blue
Blue fine
White
White fine
CTO
Macro colour
Strobe
Dimmer
Dimmer Fine
Pan
Pan Fine
Tilt
Tilt Fine
Function
Reset
Zoom
Reserved to special shape functions
Reserved to special shape functions
Reserved to special shape functions
Reserved to special shape functions
Reserved to special shape functions
Reserved to special shape functions
Reserved to special shape functions
Reserved to special shape functions
Reserved to special shape functions
Reserved to special shape functions
CHANNEL
CHANNEL MODE
CHANNEL
CHANNEL MODE
1
Red
50
BLUE LED 10
(If BLUE "channel 3" to 0)
2
Red fine
51
RED LED 11
(If RED "channel 1" to 0)
3
Green
52
GREEN LED 11 (If GREEN "channel 2" to 0)
4
Green fine
53
BLUE LED 11
(If BLUE "channel 3" to 0)
5
Blue
54
RED LED 12
(If RED "channel 1" to 0)
6
Blue fine
55
GREEN LED 12 (If GREEN "channel 2" to 0)
7
White
56
BLUE LED 12
(If BLUE "channel 3" to 0)
8
White fine
57
RED LED 13
(If RED "channel 1" to 0)
9
CTO
58
GREEN LED 13 (If GREEN "channel 2" to 0)
10
Macro colour
59
BLUE LED 13
(If BLUE "channel 3" to 0)
11
Strobe
60
RED LED 14
(If RED "channel 1" to 0)
12
Dimmer
61
GREEN LED 14 (If GREEN "channel 2" to 0)
13
Dimmer Fine
62
BLUE LED 14
(If BLUE "channel 3" to 0)
14
Pan
63
RED LED 15
(If RED "channel 1" to 0)
15
Pan Fine
64
GREEN LED 15 (If GREEN "channel 2" to 0)
16
Tilt
65
BLUE LED 15
(If BLUE "channel 3" to 0)
17
Tilt Fine
66
RED LED 16
(If RED "channel 1" to 0)
18
Function
67
GREEN LED 16 (If GREEN "channel 2" to 0)
19
Reset
68
BLUE LED 16
(If BLUE "channel 3" to 0)
20
Zoom
69
RED LED 17
(If RED "channel 1" to 0)
21
RED LED 1
(If RED "channel 1" to 0)
70
GREEN LED 17 (If GREEN "channel 2" to 0)
22
GREEN LED 1
(If GREEN "channel 2" to 0)
71
BLUE LED 17
(If BLUE "channel 3" to 0)
23
BLUE LED 1
(If BLUE "channel 3" to 0)
72
RED LED 18
(If RED "channel 1" to 0)
24
RED LED 2
(If RED "channel 1" to 0)
73
GREEN LED 18 (If GREEN "channel 2" to 0)
25
GREEN LED 2
(If GREEN "channel 2" to 0)
74
BLUE LED 18
(If BLUE "channel 3" to 0)
26
BLUE LED 2
(If BLUE "channel 3" to 0)
75
RED LED 19
(If RED "channel 1" to 0)
27
RED LED 3
(If RED "channel 1" to 0)
76
GREEN LED 19 (If GREEN "channel 2" to 0)
28
GREEN LED 3
(If GREEN "channel 2" to 0)
77
BLUE LED 19
29
BLUE LED 3
(If BLUE "channel 3" to 0)
30
RED LED 4
(If RED "channel 1" to 0)
31
GREEN LED 4
(If GREEN "channel 2" to 0)
32
BLUE LED 4
(If BLUE "channel 3" to 0)
33
RED LED 5
(If RED "channel 1" to 0)
34
GREEN LED 5
(If GREEN "channel 2" to 0)
35
BLUE LED 5
(If BLUE "channel 3" to 0)
36
RED LED 6
(If RED "channel 1" to 0)
37
GREEN LED 6
(If GREEN "channel 2" to 0)
38
BLUE LED 6
(If BLUE "channel 3" to 0)
39
RED LED 7
(If RED "channel 1" to 0)
40
GREEN LED 7
(If GREEN "channel 2" to 0)
41
BLUE LED 7
(If BLUE "channel 3" to 0)
42
RED LED 8
(If RED "channel 1" to 0)
43
GREEN LED 8
(If GREEN "channel 2" to 0)
44
BLUE LED 8
(If BLUE "channel 3" to 0)
45
RED LED 9
(If RED "channel 1" to 0)
46
GREEN LED 9
(If GREEN "channel 2" to 0)
47
BLUE LED 9
(If BLUE "channel 3" to 0)
48
RED LED 10
(If RED "channel 1" to 0)
49
GREEN LED 10 (If GREEN "channel 2" to 0)
(If BLUE "channel 3" to 0)
Continue
ALEDA WASH
15
➔
ALEDA WASH K20
STANDARD
CHANNEL
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
EXTENDED
CHANNEL MODE
Red
Red fine
Green
Green fine
Blue
Blue fine
White
White fine
CTO
Macro colour
Strobe
Dimmer
Dimmer Fine
Pan
Pan Fine
Tilt
Tilt Fine
Function
Reset
Zoom
SHAPES
CHANNEL
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
CHANNEL MODE
Red
Red fine
Green
Green fine
Blue
Blue fine
White
White fine
CTO
Macro colour
Strobe
Dimmer
Dimmer Fine
Pan
Pan Fine
Tilt
Tilt Fine
Function
Reset
Zoom
Reserved to special shape functions
Reserved to special shape functions
Reserved to special shape functions
Reserved to special shape functions
Reserved to special shape functions
Reserved to special shape functions
Reserved to special shape functions
Reserved to special shape functions
Reserved to special shape functions
Reserved to special shape functions
ALEDA WASH
CHANNEL
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
CHANNEL MODE
Red
Red fine
Green
Green fine
Blue
Blue fine
White
White fine
CTO
Macro colour
Strobe
Dimmer
Dimmer Fine
Pan
Pan Fine
Tilt
Tilt Fine
Function
Reset
Zoom
RED LED 1
GREEN LED 1
BLUE LED 1
RED LED 2
GREEN LED 2
BLUE LED 2
RED LED 3
GREEN LED 3
BLUE LED 3
RED LED 4
GREEN LED 4
BLUE LED 4
RED LED 5
GREEN LED 5
BLUE LED 5
RED LED 6
GREEN LED 6
BLUE LED 6
RED LED 7
GREEN LED 7
BLUE LED 7
RED LED 8
GREEN LED 8
BLUE LED 8
RED LED 9
GREEN LED 9
BLUE LED 9
RED LED 10
GREEN LED 10
BLUE LED 10
RED LED 11
GREEN LED 11
BLUE LED 11
RED LED 12
GREEN LED 12
BLUE LED 12
RED LED 13
GREEN LED 13
BLUE LED 13
RED LED 14
GREEN LED 14
BLUE LED 14
RED LED 15
GREEN LED 15
BLUE LED 15
RED LED 16
(If RED "channel 1" to 0)
(If GREEN "channel 2" to 0)
(If BLUE "channel 3" to 0)
(If RED "channel 1" to 0)
(If GREEN "channel 2" to 0)
(If BLUE "channel 3" to 0)
(If RED "channel 1" to 0)
(If GREEN "channel 2" to 0)
(If BLUE "channel 3" to 0)
(If RED "channel 1" to 0)
(If GREEN "channel 2" to 0)
(If BLUE "channel 3" to 0)
(If RED "channel 1" to 0)
(If GREEN "channel 2" to 0)
(If BLUE "channel 3" to 0)
(If RED "channel 1" to 0)
(If GREEN "channel 2" to 0)
(If BLUE "channel 3" to 0)
(If RED "channel 1" to 0)
(If GREEN "channel 2" to 0)
(If BLUE "channel 3" to 0)
(If RED "channel 1" to 0)
(If GREEN "channel 2" to 0)
(If BLUE "channel 3" to 0)
(If RED "channel 1" to 0)
(If GREEN "channel 2" to 0)
(If BLUE "channel 3" to 0)
(If RED "channel 1" to 0)
(If GREEN "channel 2" to 0)
(If BLUE "channel 3" to 0)
(If RED "channel 1" to 0)
(If GREEN "channel 2" to 0)
(If BLUE "channel 3" to 0)
(If RED "channel 1" to 0)
(If GREEN "channel 2" to 0)
(If BLUE "channel 3" to 0)
(If RED "channel 1" to 0)
(If GREEN "channel 2" to 0)
(If BLUE "channel 3" to 0)
(If RED "channel 1" to 0)
(If GREEN "channel 2" to 0)
(If BLUE "channel 3" to 0)
(If RED "channel 1" to 0)
(If GREEN "channel 2" to 0)
(If BLUE "channel 3" to 0)
(If RED "channel 1" to 0)
CHANNEL
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
CHANNEL MODE
GREEN LED 16
BLUE LED 16
RED LED 17
GREEN LED 17
BLUE LED 17
RED LED 18
GREEN LED 18
BLUE LED 18
RED LED 19
GREEN LED 19
BLUE LED 19
RED LED 20
GREEN LED 20
BLUE LED 20
RED LED 21
GREEN LED 21
BLUE LED 21
RED LED 22
GREEN LED 22
BLUE LED 22
RED LED 23
GREEN LED 23
BLUE LED 23
RED LED 24
GREEN LED 24
BLUE LED 24
RED LED 25
GREEN LED 25
BLUE LED 25
RED LED 26
GREEN LED 26
BLUE LED 26
RED LED 27
GREEN LED 27
BLUE LED 27
RED LED 28
GREEN LED 28
BLUE LED 28
RED LED 29
GREEN LED 29
BLUE LED 29
RED LED 30
GREEN LED 30
BLUE LED 30
RED LED 31
GREEN LED 31
BLUE LED 31
RED LED 32
GREEN LED 32
BLUE LED 32
RED LED 33
GREEN LED 33
BLUE LED 33
RED LED 34
GREEN LED 34
BLUE LED 34
RED LED 35
GREEN LED 35
BLUE LED 35
RED LED 36
GREEN LED 36
BLUE LED 36
RED LED 37
GREEN LED 37
BLUE LED 37
(If GREEN "channel 2" to 0)
(If BLUE "channel 3" to 0)
(If RED "channel 1" to 0)
(If GREEN "channel 2" to 0)
(If BLUE "channel 3" to 0)
(If RED "channel 1" to 0)
(If GREEN "channel 2" to 0)
(If BLUE "channel 3" to 0)
(If RED "channel 1" to 0)
(If GREEN "channel 2" to 0)
(If BLUE "channel 3" to 0)
(If RED "channel 1" to 0)
(If GREEN "channel 2" to 0)
(If BLUE "channel 3" to 0)
(If RED "channel 1" to 0)
(If GREEN "channel 2" to 0)
(If BLUE "channel 3" to 0)
(If RED "channel 1" to 0)
(If GREEN "channel 2" to 0)
(If BLUE "channel 3" to 0)
(If RED "channel 1" to 0)
(If GREEN "channel 2" to 0)
(If BLUE "channel 3" to 0)
(If RED "channel 1" to 0)
(If GREEN "channel 2" to 0)
(If BLUE "channel 3" to 0)
(If RED "channel 1" to 0)
(If GREEN "channel 2" to 0)
(If BLUE "channel 3" to 0)
(If RED "channel 1" to 0)
(If GREEN "channel 2" to 0)
(If BLUE "channel 3" to 0)
(If RED "channel 1" to 0)
(If GREEN "channel 2" to 0)
(If BLUE "channel 3" to 0)
(If RED "channel 1" to 0)
(If GREEN "channel 2" to 0)
(If BLUE "channel 3" to 0)
(If RED "channel 1" to 0)
(If GREEN "channel 2" to 0)
(If BLUE "channel 3" to 0)
(If RED "channel 1" to 0)
(If GREEN "channel 2" to 0)
(If BLUE "channel 3" to 0)
(If RED "channel 1" to 0)
(If GREEN "channel 2" to 0)
(If BLUE "channel 3" to 0)
(If RED "channel 1" to 0)
(If GREEN "channel 2" to 0)
(If BLUE "channel 3" to 0)
(If RED "channel 1" to 0)
(If GREEN "channel 2" to 0)
(If BLUE "channel 3" to 0)
(If RED "channel 1" to 0)
(If GREEN "channel 2" to 0)
(If BLUE "channel 3" to 0)
(If RED "channel 1" to 0)
(If GREEN "channel 2" to 0)
(If BLUE "channel 3" to 0)
(If RED "channel 1" to 0)
(If GREEN "channel 2" to 0)
(If BLUE "channel 3" to 0)
(If RED "channel 1" to 0)
(If GREEN "channel 2" to 0)
(If BLUE "channel 3" to 0)
NOTE: On conclusion of resetting in case of absence of DMX signal, Pan & Tilt move to the "Home" position (Pan 50% - Tilt 50%) all the others channels stay at 0%.
• RED – GREEN - BLUE - WHITE
• STOP / STROBE
%
255
100
EFFECT
COLOUR EXCLUDED
MACRO
BIT
0
0.0
%
255
100
0
0.0
BIT
%
255
100
%
EFFECT
98.7 - 100
93.7 - 98.2
88.7 - 93.2
83.7 - 88.2
81.7 - 83.2
81.2
OPEN
RANDOM FAST STROBE
RANDOM MEDIUM STROBE
RANDOM SLOW STROBE
OPEN
FAST PULSATION
108
104 - 107
103
42.5
41.0 - 42.0
40.5
SLOW PULSATION
OPEN
FAST STROBE (12 flash/sec)
4
0-3
1.7
0.0 - 1.2
SLOW STROBE (1 flash/sec)
CLOSED
COLOUR INSERTED
• RED FINE – GREEN FINE – BLUE FINE – WHITE FINE
BIT
BIT
252 - 255
239 - 251
226 - 238
213 - 225
208 - 212
207
• DIMMER
BIT
%
255
100
FULL LIGHT
EFFECT
0
0.0
NO LIGHT
EFFECT
• C.T.O.
• DIMMER FINE
0
0.0
EFFECT
COLOUR EXCLUDED
BIT
%
255
100
0
0.0
EFFECT
COLOUR INSERTED
• MACRO COLOUR
Continue
ALEDA WASH
17
➔
• PAN
Operation with option InvertPan Off
(Tilt conventionally represented at 14% and option Invert Tilt
G
G
GOff)
GOff)
BIT
%
BIT
%
255
100
255
100
0
0.0
0
0.0
G
Operation with option InvertPan On
(Tilt conventionally represented at 14% and option Invert Tilt
G
Operation with option InvertPan On
(Tilt conventionally represented at 14% and option Invert Tilt
GOff)
GOff)
BIT
%
BIT
%
255
100
255
100
0
0.0
0
0.0
• PAN FINE
Operation with option InvertPan Off
(Tilt conventionally represented at 14% and option Invert Tilt
G
%
255
100
0
0.0
G
• TILT FINE
Operation with option InvertPan Off
(Tilt conventionally represented at 14% and option Invert Tilt
G
GOff)
BIT
Operation with option InvertPan On
(Tilt conventionally represented at 14% and option Invert Tilt
ALEDA WASH
• TILT
Operation with option InvertPan Off
(Tilt conventionally represented at 14% and option Invert Tilt
GOff)
BIT
%
255
100
0
0.0
G
Operation with option InvertPan On
(Tilt conventionally represented at 14% and option Invert Tilt
GOff)
GOff)
BIT
%
BIT
%
255
100
255
100
0
0.0
0
0.0
18
• FUNCTION
BIT
%
255
100
EFFECT
UNUSED RANGE
52
20.5
51
20.0
39
15.0
26
10.0
13
5.0
0-12
0.0-4.7
The functions are actived passing through the "unused range" and staying 5 seconds
in necessary level
• RESET
BIT
%
EFFECT
255
100
COMPLETE RESET
Complete reset is activated passing
throug the unused range and staying
5 seconds in complete reset levels.
128
127
50.0
49.7
COMPLETE RESET
PAN / TILT RESET
Pan / Tilt reset is activated passing
throug the unused range and staying
5 seconds in Pan / Tilt reset levels.
77
76
30.0
29.7
PAN / TILT RESET
ZOOM RESET
Effects reset is activated passing
throug the unused range and staying
5 seconds in Effects reset levels.
26
25
10.0
9.7
0
0.0
ZOOM RESET
UNUSED RANGE
• ZOOM
ALEDA WASH
BIT
%
255
100
WIDE BEAM
EFFECT
0
0.0
NARROW BEAM
19
ALEDA WASH K5
TILT: channel 16 at 80%
4
5
LED
3
1
2
ALEDA WASH
6
7
20
ALEDA WASH K10
TILT: channel 16 at 80%
13
14
12
15
4
5
11
16
LED
3
1
6
10
17
2
7
9
18
8
19
Continue
ALEDA WASH
21
➔
ALEDA WASH K20
TILT: channel 16 at 80%
28
29
30
27
13
26
14
31
12
15
25
4
32
5
11
16
LED
3
24
1
6
33
10
17
2
23
7
9
22
8
19
20
37
21
ALEDA WASH
34
18
35
36
22
TIMING CHANNELS
Timing Channel
Channel function
Pan - Tilt time
Pan - Tilt - (Pan fine - Tilt fine)
Colour time
CMY - CTO - Colour wheel
Beam time
Dimmer - Zoom
TIME TABLE
BIT
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
Seconds
Full
0.2
0.4
0.6
0.8
1
1.2
1.4
1.6
1.8
2
2.2
2.4
2.6
2.8
3
3.2
3.4
3.6
3.8
4
4.2
4.4
4.6
4.8
5
5.2
5.4
5.6
5.8
6
6.2
6.4
6.6
6.8
7
7.2
7.4
7.6
7.8
8
8.2
8.4
ALEDA WASH
BIT
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
Seconds
8.6
8.8
9
9.2
9.4
9.6
9.8
10
10.2
10.4
10.6
11
12
13
14
15
16
17
18
19
20
21
22
23
BIT
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
Seconds
BIT
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
23
Seconds
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
BIT
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
Seconds
58
59
60
65
70
75
80
85
90
95
100
110
120
130
140
150
BIT
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
160
Seconds
170
180
190
200
210
220
230
240
250
260
270
280
290
300
310
Follow cue
Data
gfstudio.com
Cod. 099117-EN
PRELIMINARY 09/12
CLAY PAKY S.p.A. - Via Pastrengo, 3/b - 24068 Seriate (BG) Italy - Tel. +39-035-654311 - Fax +39-035-301876 - www.claypaky.it