DeLonghi Coffee Maker Technical data

with reduced physical, sensory or mental
capabilities or lack of experience and
knowledge if they have been given
supervision or instruction concerning use of
the appliance in a safe way and understand
the hazards involved.
Children shall not play with the appliance.
Cleaning and user maintenance shall not be
made by children without supervision.
IMPORTANT SAFEGUARDS
Symbols used in these instructions
Important warnings are identified by these symbols.
It is vital to respect these warnings.
Danger!
Failure to observe the warning could result in life threatening
injury by electric shock.
Important!
Failure to observe the warning could result in injury or damage
to the appliance.
Danger of burns!
Failure to observe the warning could result in scalds or burns.
Danger of burns!
This appliance produces hot water and steam may form while
it is in operation.
Avoid contact with splashes of water or hot steam.
When the appliance is in operation, please be aware that the
cup warmer shelf becomes hot.
Please note:
This symbol identifies important advice or information for the
user.
Fundamental safety warnings
Surfaces marked with this symbol
become hot during use (the symbol
is present in certain models only).
Danger!
This is an electrical appliance and may cause electrical shocks.
You should therefore follow these safety warnings:
• Never touch the appliance with damp hands or feet.
• Never touch the plug with damp hands.
• Make sure the socket used is freely accessible at all times,
enabling the appliance to be unplugged when necessary.
• Unplug directly from the plug only.
Never pull the power cable as you could damage it.
• To disconnect the appliance completely you must unplug it
from the mains socket.
• If the appliance is faulty, do not attempt to repair.
Turn it off, unplug from the mains socket and contact
Customer Services.
Designated use
This appliance is designed and made to prepare coffee and heat
drinks.
This is a household appliance only.
It is not intended to be used in:
• staff kitchen areas in shops, offices and
other working environments
• farm houses
• by clients in hotels, motels and other
residential type environments
• bed and breakfast type environments.
If the plug or power cable is damaged, it
must be replaced by De’Longhi Customer
Services only to avoid all risk.
During cleaning, never immerse the coffee
maker in water. It is an electrical appliance.
•
Any other use is considered improper and thus dangerous.
The manufacturer is not liable for damage deriving from
improper use of the appliance.
Before cleaning the outside of the appliance, turn it off,
unplug from the mains socket and allow to cool.
Instruction for use
Important:
Keep all packaging (plastic bags, polystyrene foam) away from
children.
Read this Instruction for Use carefully before using the
appliance. Failure to follow this Instruction for Use may result in
burns or damage to the appliance.
The manufacturer is not liable for damage deriving from failure
to respect this Instruction for Use.
Important:
This appliance can be used by children
aged from 8 years and above and persons
6
F. G. H.
I. J. K. L. M. N. O. P.
Q. R.
S.
Please note: Keep this Instruction for Use.
If the appliance is passed to other persons, they must also be
provided with this Instruction for Use.
Checking the appliance
After removing the packaging, make sure the product is
complete and undamaged and that all accessories are present.
Do not use the appliance if it is visibly damaged.
Contact De’Longhi Customer Services.
DISPOSAL
In compliance with European directive 2002/96/EC,
the appliance must not be disposed of with household
waste, but taken to an authorised waste separation
and recycling centre.
ON/OFF switch
Cup tray
Drip tray full indicator
Drip tray
Hot water/steam spout
Hot water/steam connection nozzle
Hot water/steam connection tube
Steam dial
Filter holder
Measure/presser
symbol under filter)
1 cup filter (
2 cup filter (
symbol under filter)
Pod filter (
symbol under filter)
Water softener filter (*not included, can be purchased
from authorised Customer Services)
Control panel description
T. U. V. TECHNICAL DATA
Mains voltage.......................................... 220-240V~50/60Hz
Absorbed power........................................................... 1350 W
Pressure......................................................................... 15 bar
Water tank capacity..............................................................1 l
Dimensions WxHxD............................. 149x305x330 (414)mm
Weight......................................................................... 4,04 Kg
One cup button
T1. ON light on button (white)
Two cups button
U1. ON light on button (white)
Steam button
V1. ON light on button (white)
V2. Descale light (orange)
INSTALLING THE APPLIANCE
Important!
When you install the appliance, you should respect the following
safety warnings:
• Water penetrating the appliance could cause damage.
Do not place the appliance near taps or sinks.
• The appliance could be damaged if the water it contains
freezes.
Do not install the appliance in a room where the
temperature could drop below freezing point.
• Arrange the power cable in such a way that it cannot be
damaged by sharp edges or contact with hot surfaces (e.g.
electric hot plates).
• The appliance gives off heat. After positioning the
appliance on the worktop, leave a space of at least 3 cm
between the surfaces of the appliance and the side and
rear walls and at least 15 cm above the coffee maker.
The appliance complies with the following EC
directives:
• Low Voltage Directive 2006/95/EC and subsequent
amendments;
• EMC Directive 2004/108/EC and subsequent amendments;
• European Stand-by Regulation 1275/2008;
• Materials and accessories coming into contact with food
conform to EC regulation 1935/2004.
None of the components or accessories is
dishwasher safe.
DESCRIPTION
The terminology below will be used repeatedly on the following
pages.
Connecting the appliance
Description of the appliance
(see page 3)
A. Water tank lid
B. Tank extraction handle
C. Water tank
D. Cup warmer
E. Boiler outlet
Danger!
Check that the mains power supply voltage corresponds to that
indicated on the rating plate on the bottom of the appliance.
Connect the appliance to an efficiently earthed and correctly
installed socket with a minimum current rating of 10A only. If
7
the power socket does not match the plug on the appliance,
have the socket replaced with a suitable type by a qualified
professional.
The first time you use the coffee maker, you need to make
4/5 cups of coffee or 4/5 cappuccinos before it starts to give
satisfactory results.
FILLING THE WATER TANK
PROGRAMMING THE SETTINGS MENU
1. Extract the tank by pulling it upwards (fig. 1).
2. Open the lid and fill the tank with fresh clean water, taking
care not to exceed the MAX level (fig. 2).
Put the tank back in the appliance, pressing lightly to open
the valves located on the bottom of the tank.
3. More simply, the tank can also be filled without extracting
it by pouring the water directly from a jug.
To access the menu, make sure the appliance is ready for use,
then press and hold the
button for 10 seconds until the
three buttons flash in sequence:
The appliance is now in programming mode.
Set the coffee maker as you wish, then exit the settings menu by
waiting for 15 seconds.
Please note:
If no selections are made for 15 seconds, the appliance
automatically exits programming and is ready for use again.
Important:
Never operate the appliance without water in the tank or
without the tank.
Please note:
It is normal for there to be water in the space under the tank.
This should therefore be dried regularly with a clean sponge.
Setting coffee temperature
SETTING UP THE APPLIANCE
button to enter the coffee temperature
2. Press the
selection mode.
The lights corresponding to the current selection come on:
•
To modify the temperature of the water used to make the coffee,
proceed as follows:
1. Access the settings menu;
Turn the appliance on by pressing the ON/OFF switch (fig.
3). The appliance performs a self-diagnosis cycle, indicated
by sequential flashing of the three buttons.
low
and
lights flash to indicate the appliance
•The
is heating up.
When the lights stop flashing and remain on steadily, the
appliance is ready for use.
• Place a container with a minimum capacity of 100 ml
under the hot water/steam spout (fig. 4).
position (fig.
• Turn the hot water/steam dial to the
5) and deliver about 100 ml of water, then close the dial
again (○ symbol).
• Attach the filter holder to the appliance. To attach correctly,
align the filter holder handle with the INSERT symbol (fig.
9), attach the filter holder and rotate the handle towards
the right until aligned with the CLOSE symbol.
• To rinse the machine’s internal circuits, place a con-
•
medium
high
3. The lights start flashing in sequence;
4. Press the button corresponding to the required
temperature:
low medium
high
flashes to indicate that the selection has
5. The button
been saved.
The appliance exits the menu and is ready for use.
tainer under the coffee spout and press the
key. Repeat this procedure 5 times.
Then proceed with rinsing the “steam” circuit: place
a container under the hot water spout and turn the
dial to the
position. Hot water is delivered.
When the appliance automatically stops the hot
water delivery, close the dial (○symbol). Repeat this
procedure 1 more time (If necessary, refill the tank).
Setting water hardness
The light (V2) indicating that the appliance needs descaling
comes on after a period of operation established according to
water hardness.
The appliance can also be programmed according to the
hardness of the mains water in the various regions so that
descaling needs to be performed more or less frequently.
Proceed as follows:
1. Access the settings menu;
Please note:
8
Default values (reset)
2. Press the
button to enter the water hardness
selection mode. The lights corresponding to the current
selection come on:
This resets all menu settings and programmed quantities back
to the default values.
To reset the default values, proceed as follows:
1. Access the settings menu;
position;
2. Turn the steam dial to the
soft
medium
button. The three lights flash
3. Press the
simultaneously to confirm that the original settings have
been restored.
hard
and
lights flash to indicate that the
4.The
steam dial must be closed again (○symbol).
When the steam dial has been closed, the appliance is ready for
use.
3. The lights start flashing in sequence;
4. Press the button corresponding to the water hardness in
your area:
soft
water
medium
water
hard
water
<10°dH
10°dH - 20°dH
>20°dH
<18°fH
18°fH - 36°fH
>36°fH
HOW TO MAKE ESPRESSO COFFEE
Tips for a hotter coffee
For hotter espresso coffee, you should:
• Attach the filter holder to the appliance with the filter in
place but without adding coffee.
Using the same cup as will later be used to make the coffee,
press the 1 cup button and deliver hot water into the cup to
heat it.
• Raise the coffee temperature in the settings menu.
• Rest the cups you will be using on the cup warmer (D)
which becomes hot during operation.
<180mg/l CaCo3 180-300mg/l CaCo3 360mg/l CaCo3
-The
button flashes to indicate that the selection has
been saved.
The appliance exits the menu and is ready for use.
Adjusting auto-off (stand-by)
To save energy, an auto-off function turns the appliance off
when not used for a long period.
To turn it back on again, press any button on the control panel.
1. Access the settings menu;
How to make espresso coffee using pre-ground
coffee
1. Place the ground coffee filter (P or Q) in the filter holder
(fig. 6). To make one coffee, use the filter with the
symbol on the bottom, to make two coffees, use the filter
with the
symbol on the bottom.
2. To make just one coffee, place one level measure of preground coffee (about 7 g) in the filter (fig. 7).
To make two coffees, place two loosely filled measures
(about 7+7 g) of pre-ground coffee in the filter. Fill the
filter a little at a time to prevent the pre-ground coffee
from overflowing.
2. Press the
button to enter the auto-off time selection
mode. The lights corresponding to the current selection
come on:
9 min
30 min
3 hours
3. The lights start flashing in sequence;
4. Press the button corresponding to the required time:
Important:
For correct operation, before filling with pre-ground coffee,
make sure there are no coffee residues left in the filter from the
last time you made coffee.
3. Distribute the pre-ground coffee evenly and press lightly
with the presser (fig. 8). Correct pressing of the pre-ground
coffee is essential to obtain a good espresso. If you press
too firmly, the coffee will be delivered slowly and will be
strong. If you press too lightly, the coffee will be delivered
quickly and will be weak.
9 min
30 min
3 hours
5.The
button flashes to indicate that the selection has
been saved.
The appliance exits the menu and is ready for use.
9
4. Remove any excess coffee from the rim of the filter holder
and attach the filter holder to the appliance. To attach
correctly, align the filter holder handle with the INSERT
symbol (fig. 9), attach the filter holder and rotate the
handle towards the right until aligned with the CLOSE
symbol.
5. Place the cup or cups under the filter holder spouts (fig.
10). You are recommended to warm the cups before
making coffee by rinsing them with a little hot water.
6. Make sure the lights corresponding to the coffee buttons
To change these quantities, proceed as follows:
1. Place one or two cups under the filter holder spouts.
2. Press and hold the button you want to programme (
or
). The appliance starts delivering coffee and the
other coffee button flashes to indicate that programming
is underway.
3. Once the required quantity of coffee has been delivered
into the cup, release the button. Delivery stops and the
light flashes to indicate that the quantity has been saved
correctly.
4. When the two coffee lights come on steadily, the appliance
is ready for use.
or
coffee button. The
are on, then press the
appliance proceeds to make the coffee and delivery is
interrupted automatically.
HOW TO MAKE CAPPUCCINO
How to make espresso coffee using pods
1. Prepare the espresso coffees as described in the previous
paragraphs, using sufficiently large cups.
Please note:
use pods conforming to the ESE standard, indicated on the pack
by the following symbol.
The ESE standard is a system accepted by
leading pod producers and enables espresso
coffee to be prepared simply and cleanly.
2. Press the
button (fig. 12). The light flashes;
3. In the meantime, fill a recipient with about 100 g of milk
for each cappuccino to be prepared.
The milk must be at refrigerator temperature (not hot!).
In choosing the size of the recipient, bear in mind that the
milk doubles or triples in volume (fig. 13).
Please note:
You are recommended to use semi-skimmed milk at refrigerator
temperature.
1. Place the filter for coffee pods (with the
symbol on
the bottom) in the filter holder.
2. Insert the pod, centring it as far as possible on the filter
(fig. 11). Always follow the instructions on the pod pack to
position the pod on the filter correctly.
Proceed as described in points 4 to 6 in the previous section.
4. Wait for the light corresponding to the
button to
come on steadily, indicating that the boiler has reached
the ideal temperature to produce steam.
5. Position an empty container under the cappuccino maker
and open the dial for a few seconds to eliminate any air left
in the circuit. Close the dial again.
6. Place the recipient containing the milk under the
cappuccino maker.
7. Dip the cappuccino maker in the milk for a few millimetres
(fig. 14).
position. Steam is delivered
Turn the dial to the
from the cappuccino maker, giving the milk a creamy
frothy appearance. To obtain a creamier froth, immerse the
cappuccino maker in the milk and rotate the container with
slow upward movements.
8. When the milk has doubled in volume, immerse the
cappuccino maker deeply and continue heating the milk
(fig. 15). When the required temperature (the ideal is 60°C)
and froth density is reached, interrupt steam delivery by
turning the steam dial clockwise.
9. Pour the frothed milk into the cups containing the espresso
coffee prepared previously.
Please note:
• While the appliance is making coffee, delivery can be
interrupted at any moment by pressing the coffee button
pressed previously.
• At the end of delivery (within 3 seconds), to increase the
amount of coffee in the cup, press and hold the coffee
button pressed previously. Delivery is automatically
interrupted after a few seconds.
• To remove the filter holder, turn the handle from right to
left.
Danger of burns!
To avoid splashes, never remove the filter holder while the
appliance is delivering coffee. Always wait for a few seconds
after delivery.
Programming the quantities of coffee in the cup
The appliance is set by default to automatically deliver standard
quantities.
10
•
•
The cappuccino is ready. Sweeten to taste and if desired,
sprinkle the froth with a little cocoa powder.
2. Place a recipient under the cappuccino maker.
position. Hot water is delivered
3. Turn the dial to the
from the cappuccino maker.
4. To stop hot water delivery, close the dial and press any
button.
Please note:
to prepare more than one cappuccino, first make all the
coffees then at the end prepare the frothed milk for all the
cappuccinos.
to exit the steam function, press any button. The lights
You should not deliver hot water for more
than 60 seconds.
and
flash to indicate that the temperature is
too high to make coffee (see section “Cooling the boiler”).
CLEANING
You should not deliver steam for more than
60 seconds.
Danger!
Before cleaning the outside of the appliance, turn it off, unplug
from the mains socket and allow to cool.
Important:
For hygiene reasons, the cappuccino maker should always be
cleaned after use.
Proceed as follows:
1. Turn the steam dial to deliver a little steam for a few
seconds (points 2, 4 and 5 of the previous section).
This causes the cappuccino maker to deliver any milk left in
its circuits. Press the ON/OFF button to turn the appliance
off.
2. With one hand, hold the cappuccino maker tube firmly,
with the other, release the cappuccino maker by turning it
clockwise, then pull off downwards (fig. 16).
3. Remove the rubber steam connection nozzle from the
spout by pulling it downwards (fig. 17).
4. Wash the cappuccino maker and steam connection nozzle
thoroughly with warm water (fig. 18).
5. Check the hole shown by the arrow in fig. 18 is not blocked.
6. Put the steam connection nozzle back, pressing upwards to
insert it onto the steam tube.
7. Replace the cappuccino maker by pushing upwards and
turning anticlockwise.
Cleaning the drip tray
Important!
The drip tray is fitted with a level indicator (red) showing the
level of water it contains (fig. 19).
Before the indicator protrudes from the cup tray, the drip
tray must be emptied and cleaned, otherwise the water may
overflow the edge and damage the appliance, the surface it
rests on or the surrounding area.
1. Remove the drip tray (fig. 20).
2. Remove the cup tray, empty the water and clean the drip
tray with a cloth, then reassemble the drip tray.
3. Put the drip tray back in place.
Cleaning the coffee filters
Clean the coffee filters regularly by rinsing under running water.
Make sure the holes are not blocked. If necessary, clean with a
pin (fig. 21).
Cleaning the boiler outlet
After every 200 coffees, rinse the boiler outlet by delivering
about 0.5 l of water from the boiler outlet (press the coffee
button without using ground coffee).
Cooling the boiler
To make coffee again immediately after frothing milk, the boiler
must first be cooled or the coffee will be burnt.
Proceed as follows:
• place a container under the cappuccino maker;
• open the steam dial to deliver hot water and cool the
boiler;
• hot water delivery is interrupted automatically when the
boiler is cool. When the pump stops operating and no more
water is delivered, close the steam dial.
The coffee maker is now ready for use.
Other cleaning operations
1. Do not use solvents or abrasive detergents to clean the
coffee maker. Use a soft damp cloth only.
2. Clean the filter holder cup regularly.
Cleaning the water tank
Clean the water tank regularly (about once a month) with a
damp cloth and a little mild washing up liquid.
Danger!
During cleaning, never immerse the coffee maker in water. It is
an electrical appliance.
HOT WATER
1. Turn the appliance on by pressing the ON/OFF button (fig.
4). Wait for the coffee lights to come on steadily.
11
Descaling
12. Empty the container used to collect the descaler solution
and replace it empty under the hot water spout.
13. Make sure the steam dial is in the
, position, then
Descale the appliance when the orange light on the
button comes on.
press the
Important!
• Descaler contains acids which may irritate the skin and
eyes. It is vital to respect the manufacturer’s safety
warnings given on the descaler pack and the warnings
relating to the procedure to follow in the event of contact
with the skin and eyes.
• You should use De’Longhi descaler only. Using unsuitable
descaler and/or performing descaling incorrectly may
result in faults not covered by the manufacturer’s
guarantee.
Proceed as follows:
1. Completely empty the water tank and REMOVE THE
button to start rinsing.
Please note:
During rinsing, to clean the boiler outlet, close the steam dial
from time to time to deliver small quantities of water from the
boiler outlet.
14. Extract the water tank and fill with fresh water up to the
MAX level, then repeat once steps 12 to 14.
15. Make sure the steam dial is in the closed position
(○symbol).
The appliance is ready for use.
SOFTENER FILTER (if present).
Repair of damage to the coffee maker caused by scale is not
covered by the guarantee unless descaling is performed
regularly as described above.
2. Fill the tank with the descaler solution obtained by diluting
the descaler with water following the instructions on the
pack.
3. Press the ON/OFF button.
4. Make sure the filter holder is not attached and position a
recipient under the cappuccino maker.
and
lights to come on steadily,
5. Wait for the
indicating that the appliance is ready for use.
6. Press and hold the
button for 10 seconds until the
three buttons flash in sequence.
position.
7. Turn the steam dial to the
8. Press the
button to start descaling.
9. The descale programme starts and the descaler liquid
comes out of the water spout.
The descale programme removes limescale deposits from
inside the appliance by automatically performing a series
of rinses and pauses until the tank is completely empty.
Please note:
During descaling, to clean the boiler outlet, close the steam dial
from time to time to deliver small quantities of descaler from
the boiler outlet.
10. The appliance stops operation and the orange
light continues to flash, indicating that descaling is still
underway.
11. The coffee maker is now ready for rinsing through with
clean water.
Extract the water tank, empty, rinse under running water,
fill with fresh water up to the MAX level, reinsert the
softner filter (if previously removed) and put back in the
appliance.
12
EXPLANATION OF LIGHTS
Lights
Operation
Explanation of lights
The ON/OFF button is turned on
The appliance performs a self-diagnosis
cycle, indicated by sequential flashing off
the lights
The appliance is on
Flashing lights: the appliance is heating
up to make coffee
Lights on steadily: the appliance is ready
to make coffee
The lights flash rapidly: the tank is empty
or the appliance will not make coffee
See section: “Troubleshooting”
The steam function is required
Flashing light: the appliance is heating
up to deliver steam
Light on steadily: the appliance is ready
to deliver steam
Steam dial open
Flashing lights: close the steam dial
High boiler temperature
Flashing lights: Cool the boiler as described in the corresponding section
TROUBLESHOOTING
Problem
Cause
Solution
No espresso coffee is delivered
No water in the tank
Fill the tank
The holes in the filter holder are blocked
Clean the filter holder spout holes
The tank has been inserted incorrectly Press the tank down lightly to open the valves on
and the valves on the bottom are not the bottom
open
Limescale in the water circuit
The espresso coffee drips from The filter holder has been inserted incorthe edges of the filter holder rectly or is dirty
rather than the holes
Attach the filter holder correctly and rotate firmly as far as it will go
Descale as described in the section “Descaling”
Attach the filter holder correctly and rotate firmly
as far as it will go
Have the espresso boiler gasket replaced by Customer Services
The holes in the filter holder spouts are Clean the spout holes
blocked
The filter holder cannot be atta- Too much coffee has been placed in the Use the measure supplied and make sure you are
ched to the appliance
filter
using the correct filter for the type of preparation
13
The coffee froth is too light (de- The pre-ground coffee is not pressed Press the pre-ground coffee more firmly
livered from the spout too fast) down firmly enough
There is not enough pre-ground coffee
Increase the quantity of pre-ground coffee
The pre-ground coffee is too coarse
Use only pre-ground coffee for espresso coffee
makers
The wrong type of pre-ground coffee is Change the type of pre-ground coffee
being used
The coffee froth is too dark The pre-ground coffee is pressed down Press the coffee down less firmly
(delivered from the spout too too firmly
slowly)
There is too much pre-ground coffee
Reduce the quantity of pre-ground coffee
The espresso boiler outlet is blocked
Clean as described in the section “Cleaning the
boiler outlet”
The filter is blocked
Clean as described in the section “Cleaning the
filter”
The pre-ground coffee is too fine
Use only pre-ground coffee for espresso coffee
makers
The pre-ground coffee is too fine or Use pre-ground coffee for espresso coffee makers
damp
only and make sure it is not too damp
Limescale in the water circuit
Descale as described in the section “Descaling”
After delivering coffee, the filter
remains attached to the boiler
outlet
Insert the filter holder again, deliver coffee, then
remove the filter holder
The appliance will not make No water in the tank
Fill the tank with water
any drink and the
,
The tank has been inserted incorrectly Press the tank down lightly to open the valves on
lights flash for a few and the valves on the bottom are not the bottom
and
open
seconds
The espresso boiler outlet is blocked
Clean as described in the section “Cleaning the
boiler outlet”
The filter is blocked
Clean as described in the section “Cleaning the
filter”
Limescale in the water circuit
Descale as described in the section “Descaling”
The appliance does not function and all the lights flash
With an extreme use, the appliance reaches a high
temperature. Simply wait: the appliance will cool
down automatically
The appliance does not fun- Abnormal machine conditions
ction and all the lights flash for
a long time
Disconnect the appliance and contact authorised
Customer Services.
14