Uniwell NX-5400 type 01 programming Manual - THE

Uniwell NX-5400 type 01 programming Manual
NX-5400
01 type
Programming
Manual
Nov.12.2001
CAUTION!
When the control key position is OFF, the display is off
and keyboard is disabled but the ECR's power is still
ON. So that before you open the upper case, make sure
that the AC cord is disconnected. Especially when you
replace the ROM, it must be disconnected, otherwise the
ECR will be damaged.
CONTENTS OF PROGRAMMING MANUAL
BEFORE INSTALLATION................................................................................................................. 1
INTRODUCTION................................................................................................................................. 2
SPECIFICATIONS............................................................................................................................... 3
SYSTEM CONFIGURATION ................................................................................................................... 4
NO RAM CHIP EXPANSION.................................................................................................................... 5
SET-UP OF PERIPHERALS...................................................................................................................... 5
I. STANDARD KEY LAYOUT .......................................................................................................... 6
II. PROGRAMMING .......................................................................................................................... 8
KEYBOARD PROGRAMMING ............................................................................................................... 8
(PGM-101) KEY LAYOUT.................................................................................................................................. 8
PLU & GROUP PROGRAMMING......................................................................................................... 11
(PGM-201/4201) PLU CODE ............................................................................................................................. 12
(PGM-203/4203) PLU LINK TO GROUP.......................................................................................................... 13
(PGM-305/4305) PLU PRICE............................................................................................................................. 14
(PGM-320/4320) PLU HALO (High Amount Lock-Out) ................................................................................... 15
(PGM-200/4200) PLU FUNCTION.................................................................................................................... 16
(PGM-204) PLU LINK TO ONE PLU ............................................................................................................... 19
(PGM-209/4209) PLU LINK TO SUPPLEMENTARY MESSAGE.................................................................. 19
(PGM-223/4223) GROUP-A LINK TO MAIN GROUP-A................................................................................ 20
(PGM-109) PLU MODIFIER.............................................................................................................................. 20
(PGM-111) MENU LAYOUT ............................................................................................................................ 21
(PGM-4111) MENU LAYOUT COPY PROCEDURE ...................................................................................... 21
(PGM-406) PLU STOCK.................................................................................................................................... 22
(PGM-426) GROUP-A STOCK.......................................................................................................................... 22
CHARACTER PROGRAMMING........................................................................................................... 23
Character Code Table........................................................................................................................................... 24
How to Preset Characters ..................................................................................................................................... 25
RATE PROGRAMMING ......................................................................................................................... 30
(PGM-337) PERCENTAGE RATE .................................................................................................................... 30
(PGM-347) ADJUSTMENT RATE .................................................................................................................... 31
(PGM-357) SALES COMMISSION RATE........................................................................................................ 31
(PGM-367) STOCK RATE ................................................................................................................................. 31
(PGM-377) CHEQUE-CASHING CHARGE RATE......................................................................................... 31
CURRENCY EXCHANGE CHARGE RATE..................................................................................................... 31
(PGM-107) TAX RATE...................................................................................................................................... 31
(PGM-108) TAX EXEMPTION LIMIT FOR % TAX ....................................................................................... 32
TAX TABLE FOR ADD-ON TAX SYSTEM..................................................................................................... 32
(PGM-387) FOREIGN CURRENCY EXCHANGE RATE................................................................................ 33
(PGM-397) EURO CURRENCY RATE [SF-13.e=1] ........................................................................................ 33
CASHIER PROGRAMMING .................................................................................................................. 34
(PGM-211) SECRET CASHIER CODE............................................................................................................. 34
MISCELLANEOUS PROGRAMMING ................................................................................................. 35
(PGM-131)
(PGM-141)
(PGM-151)
(PGM-171)
(PGM-179)
(PGM-325)
(PGM-172)
(PGM-315)
(PGM-121)
(PGM-189)
Z1-REPORT SECRET CODE......................................................................................................... 35
Z2-REPORT SECRET CODE......................................................................................................... 35
TRAINING SECRET CODE........................................................................................................... 35
MACHINE NUMBER..................................................................................................................... 35
SLIP PRINTER ID # FOR TP-620 .................................................................................................. 35
+ / - AMOUNT ................................................................................................................................ 35
TERMINAL ADDRESS.................................................................................................................. 36
PRESET TENDER AMOUNT ........................................................................................................ 36
ARRANGEMENT KEY SEQUENCE ............................................................................................ 37
CHEQUE PRINTING FORMAT .................................................................................................... 38
TIME & DATE PROGRAMMING ......................................................................................................... 41
(PGM-1) DATE................................................................................................................................................... 41
(PGM-2) TIME ................................................................................................................................................... 41
SYSTEM PROGRAMMING.................................................................................................................... 42
(PGM-100) SYSTEM FUNCTION..................................................................................................................... 42
PROGRAMMING REFERENCE............................................................................................................ 68
IV. REPORTS..................................................................................................................................... 72
REPORT SEQUENCE .............................................................................................................................. 72
IRC REPORT SEQUENCE...................................................................................................................... 74
PROGRAM DUMP CONTENTS............................................................................................................. 75
V. SERVICE PROGRAMMING...................................................................................................... 78
INITIAL RESET........................................................................................................................................ 78
TEST PROGRAMS ................................................................................................................................... 79
RAM TEST .......................................................................................................................................................... 79
ROM TEST .......................................................................................................................................................... 79
PLU DATA ERASE............................................................................................................................................. 79
HARDWARE TEST ............................................................................................................................................ 79
AUTO PRESET ......................................................................................................................................... 81
IRC PROGRAM DATA TRANSFER...................................................................................................... 83
VI. WARNING MESSAGES............................................................................................................. 84
This is a “Table of Contents preview” for quality assurance
The full manual can be found at http://the-checkout-tech.com/estore/catalog/
We also offer free downloads, a free keyboard layout designer, cable diagrams, free help and
support.
http://the-checkout-tech.com : the biggest supplier of cash register and scale manuals on the net