HP Pavilion DV6057 System information

HP Pavilion dv6 Entertainment PC
Maintenance and Service Guide
© Copyright 2009 Hewlett-Packard
Development Company, L.P.
AMD Athlon, ATI Mobility Radeon, AMD
Sempron, and AMD Turion are trademarks of
Advanced Micro Devices, Inc. Bluetooth is a
trademark owned by its proprietor and used
by Hewlett-Packard Company under license.
Intel is a registered trademark of
Intel Corporation in the U.S. and
other countries. Microsoft, Windows, and
Windows Vista are U.S. registered
trademarks of Microsoft Corporation.
SD Logo is a trademark of its proprietor.
The information contained herein is subject
to change without notice. The only
warranties for HP products and services are
set forth in the express warranty statements
accompanying such products and services.
Nothing herein should be construed as
constituting an additional warranty. HP shall
not be liable for technical or editorial errors
or omissions contained herein.
Second Edition: May 2009
First Edition: March 2009
Document Part Number: 532395-002
Safety warning notice
WARNING! To reduce the possibility of heat-related injuries or of overheating the computer, do not
place the computer directly on your lap or obstruct the computer air vents. Use the computer only on a
hard, flat surface. Do not allow another hard surface, such as an adjoining optional printer, or a soft
surface, such as pillows or rugs or clothing, to block airflow. Also, do not allow the AC adapter to contact
the skin or a soft surface, such as pillows or rugs or clothing, during operation. The computer and the
AC adapter comply with the user-accessible surface temperature limits defined by the International
Standard for Safety of Information Technology Equipment (IEC 60950).
iii
iv
Safety warning notice
Table of contents
1 Product description
2 External component identification
Top components ................................................................................................................................... 6
TouchPad ............................................................................................................................ 6
Lights ................................................................................................................................... 7
Buttons, speakers and fingerprint reader ............................................................................. 9
Keys ................................................................................................................................... 11
Front components .............................................................................................................................. 12
Rear component ................................................................................................................................. 13
Right-side components ....................................................................................................................... 13
Left-side components ......................................................................................................................... 14
Bottom components ........................................................................................................................... 15
Display components ........................................................................................................................... 16
Cleaning the display .......................................................................................................... 16
Wireless antennas (select models only) ............................................................................................. 17
3 Illustrated parts catalog
Service tag ......................................................................................................................................... 18
Computer major components ............................................................................................................. 19
Display assembly components ........................................................................................................... 26
AntiGlare display assembly spare parts ............................................................................ 26
BrightView display assembly spare parts .......................................................................... 27
Plastics Kit .......................................................................................................................................... 28
Cable Kit ............................................................................................................................................. 29
Miscellaneous parts ............................................................................................................................ 30
Sequential part number listing ............................................................................................................ 31
4 Removal and replacement procedures
Preliminary replacement requirements ............................................................................................... 41
Tools required .................................................................................................................... 41
Service considerations ....................................................................................................... 41
Plastic parts ....................................................................................................... 41
v
Cables and connectors ..................................................................................... 42
Drive handling ................................................................................................... 42
Grounding guidelines ......................................................................................................... 43
Electrostatic discharge damage ........................................................................ 43
Packaging and transporting guidelines ............................................. 44
Workstation guidelines ..................................................................... 44
Equipment guidelines ....................................................................... 45
Component replacement procedures ................................................................................................. 46
Service tag ......................................................................................................................... 46
Computer feet .................................................................................................................... 47
Battery ............................................................................................................................... 48
Webcam/microphone module ............................................................................................ 49
Optical drive ....................................................................................................................... 51
Memory module ................................................................................................................. 53
TV tuner module ................................................................................................................ 55
RTC battery ....................................................................................................................... 56
Hard drive .......................................................................................................................... 57
WLAN module .................................................................................................................... 60
Switch cover and keyboard ................................................................................................ 63
Power button board ........................................................................................................... 67
Display assembly ............................................................................................................... 68
Speaker ............................................................................................................................. 78
Bluetooth module ............................................................................................................... 79
Top cover ........................................................................................................................... 80
Modem module .................................................................................................................. 83
Audio/infrared board .......................................................................................................... 84
USB board ......................................................................................................................... 85
Power connector cable ...................................................................................................... 86
System board ..................................................................................................................... 88
TV tuner module cable ....................................................................................................... 90
Modem module cable ........................................................................................................ 91
Fan/heat sink assembly ..................................................................................................... 92
Processor ........................................................................................................................... 96
5 Setup Utility
Starting the Setup Utility ..................................................................................................................... 98
Using the Setup Utility ........................................................................................................................ 99
Changing the language of the Setup Utility ....................................................................... 99
Navigating and selecting in the Setup Utility ...................................................................... 99
Displaying system information ......................................................................................... 100
Restoring default settings in the Setup Utility .................................................................. 100
Exiting the Setup Utility .................................................................................................... 100
Setup Utility menus .......................................................................................................................... 101
vi
Main menu ....................................................................................................................... 101
Security menu .................................................................................................................. 101
System Configuration menu ............................................................................................ 101
Diagnostics menu ............................................................................................................ 102
6 Specifications
Computer specifications ................................................................................................................... 103
15.6-inch, WXGA display specifications ........................................................................................... 104
16.0-inch WXGA BrightView display specifications .......................................................................... 105
16.0-inch WXGA AntiGlare display specifications ............................................................................ 106
Hard drive specifications .................................................................................................................. 107
Blu-ray ROM DVD±R/RW SuperMulti Double-Layer Drive specifications ........................................ 108
DVD±RW SuperMulti Double-Layer Combo Drive specifications .................................................... 109
System DMA specifications .............................................................................................................. 110
System interrupt specifications ......................................................................................................... 111
System I/O address specifications ................................................................................................... 112
System memory map specifications ................................................................................................. 114
7 Screw listing
Phillips PM2.0×3.0 screw ................................................................................................................. 116
Phillips PM2.0×14.0 captive screw ................................................................................................... 119
Phillips PM2.5×3.0 screw ................................................................................................................. 121
Phillips PM2.5×4.0 screw ................................................................................................................. 122
Phillips PM2.5×6.0 screw ................................................................................................................. 124
Phillips PM2.0×2.0 broadhead screw ............................................................................................... 125
Phillips PM2.5×5.0 screw ................................................................................................................. 126
Phillips PM2.5×5.0 captive screw ..................................................................................................... 128
Phillips PM2.5×5.5 captive screw ..................................................................................................... 130
Phillips PM2.5×7.0 screw ................................................................................................................. 131
Phillips PM3.0×3.5 screw ................................................................................................................. 134
8 Backup and Recovery
Recovering system information ........................................................................................................ 135
Creating recovery discs ................................................................................................... 136
Backing up your information ............................................................................................................. 137
When to back up .............................................................................................................. 137
Backup suggestions ......................................................................................................... 137
Using system restore points ............................................................................................ 137
When to create restore points ......................................................................... 137
Create a system restore point ......................................................................... 138
Restore to a previous date and time ............................................................... 138
Performing a recovery ...................................................................................................................... 139
Recovering from the recovery discs ................................................................................ 139
vii
Recovering from the dedicated recovery partition (select models only) .......................... 139
9 Connector pin assignments
1394 ................................................................................................................................................. 140
Audio-in (microphone) ...................................................................................................................... 140
Audio-out (headphone) ..................................................................................................................... 141
External monitor ............................................................................................................................... 141
HDMI ................................................................................................................................................ 142
RJ-11 (modem) ................................................................................................................................ 143
RJ-45 (network) ................................................................................................................................ 143
Universal Serial Bus ......................................................................................................................... 144
10 Power cord set requirements
Requirements for all countries or regions ......................................................................................... 145
Requirements for specific countries or regions ................................................................................ 146
11 Recycling
Battery .............................................................................................................................................. 147
Display .............................................................................................................................................. 147
Index ................................................................................................................................................................. 153
viii
1
Product description
Category
Description
Product Name
HP Pavilion dv6 Entertainment PC
√
√
Processors
AMD Turion™ ZM-87, 2.4-GHz with 2-MB L2 cache
√
√
AMD Turion ZM-86, 2.4-GHz with 2-MB L2 cache
√
√
AMD Turion ZM-85, 2.3-GHz with 2-MB L2 cache
√
√
AMD Turion ZM-84, 2.3-GHz with 2-MB L2 cache
√
√
AMD Turion ZM-82, 2.2-GHz with 2-MB L2 cache
√
√
AMD Turion RM-77, 2.3-GHz with 2-MB L2 cache
√
√
AMD Turion RM-75, 2.2-GHz with 2-MB L2 cache
√
√
AMD Turion RM-74, 2.2-GHz with 2-MB L2 cache
√
√
AMD Athlon™ QL-67, 2.2-GHz with 1-MB L2 cache
√
√
AMD Athlon QL-65, 2.1-GHz with 1-MB L2 cache
√
√
AMD Athlon QL-64, 2.1-GHz with 1-MB L2 cache
√
√
AMD Sempron™ SI-42, 2.1-GHz with 512-KB L2 cache
√
√
Northbridge: AMD M780G Chipset
√
Chipset
Computers
with discrete
graphics
Northbridge: AMD M770 Chipset
Graphics
Computers
UMA
graphics
√
Southbridge: SB700
√
ATI Mobility Radeon™ HD 4650 (M96) with 1 GB of dedicated
video memory (64 MB × 16 DDR3 × 8 PCs)
√
ATI Mobility Radeon HD 4530 (M92) with 512 MB of dedicated
video memory (64 MB × 16 DDR3 × 4 PCs)
√
√
AMD internal graphics with 64-MB SidePort video memory (32
MB × 16)
√
Unified memory architecture (UMA) with shared video memory
(ATI Radeon HD 3200 graphics):
√
●
Up to 251 MB for = 1024-MB system RAM
●
Up to 358 MB for > 2048-MB system RAM
●
Memory size is dynamic change
1
Category
Panels
Memory
Hard drives
2
Chapter 1 Product description
Description
Computers
Computers
with discrete UMA
graphics
graphics
Support for BD playback with HD Decode, and DX10
√
√
●
15.6-inch WXGA (1366 × 768) BrightView LED
√
√
●
15.6-inch WXGA (1366 × 768) AntiGlare LED
√
√
●
16.0-inch WXGA (1366 × 768) BrightView LED
√
√
●
16.0-inch WXGA (1366 × 768) AntiGlare LED
√
√
●
15.6-inch cold cathode fluorescent lamps (CCFL) panel
√
√
●
16.0-inch CCFL panel
√
√
●
AntiGlare glass panel cover support
√
√
●
Support for lighted logo on display enclosure
√
√
●
Typical brightness 160 nits
√
√
2 SODIMM slots
√
√
Customer-accessible/upgradable
√
√
PC2-6400, 800-MHz, DDR2
√
√
Dual-channel support
√
√
Supports up to 8-GB system memory
√
√
Supports all Serial ATA (SATA) 9.5-mm, 6.35-cm (2.50-in)
hard drives
√
√
Supports one hard drive
√
√
Support for HP ProtectSmart Hard Drive Protection
√
√
●
1024-MB total system memory (1024 MB × 1, dualchannel)
●
2048-MB total system memory (1024 MB × 2, dualchannel)
●
2048-MB total system memory (2048 MB × 1, dualchannel)
●
3072-MB total system memory (2048 MB + 1024 MB)
●
4096-MB total system memory (2048 MB × 2, dualchannel)
●
6144-MB total system memory (2048 MB + 4096 MB)
●
8192-MB total system memory (4096 MB × 2, dualchannel)
Category
Description
Single hard drive configurations:
Computers
with discrete
graphics
Computers
UMA
graphics
√
√
12.7-mm tray load
√
√
Serial ATA (SATA)
√
√
Fixed (removal of one screw required)
√
√
Supports the following optical drives:
√
√
Standard VGA camera
√
√
Fixed (no tilt)
√
√
Activity LED
√
√
640 × 480 by 24 frames per second
√
√
Microphone
2 omnidirectional digital microphones, dual-array with
appropriate software (supports beam forming, echo
cancellation, and noise suppression)
√
√
Audio
HD Audio
√
√
Supports Microsoft® Premium Requirements
√
√
Pavilion-branded Altec Lansing speakers
√
√
56K V.92 data/fax modem (select models only)
√
√
Supports all worldwide certification requirements
√
√
Integrated Realtek 10/100/1000 network interface card (NIC)
√
Optical drives
Webcam
Modem
Ethernet
●
160 GB (5400 rpm)
●
250 GB (7200 rpm) (select models only)
●
250 GB (5400 rpm)
●
320 GB (7200 rpm) (select models only)
●
320 GB (5400 rpm)
●
500 GB (5400 rpm)
●
DVD±RW and CD-RW SuperMulti Double-Layer Combo
Drive
●
Blu-ray ROM with LightScribe DVD±R/RW SuperMulti
Double-Layer Drive
Integrated Realtek 10/100 NIC
Wireless
TV tuner
√
Integrated wireless local area network (WLAN) options by way of wireless module:
Atheros 9285G 802.11b/g + Bluetooth® with two antennas
√
√
Broadcom BCM4312 802.11b/g + Bluetooth with two antennas
√
√
Atheros 9280AGN 802.11a/b/g/n + Bluetooth
√
√
Broadcom BCM4312 802.11b/g + Bluetooth
√
√
Integrated DVB-T TV tuner (select models only)
√
√
3
Category
External media card
Internal card expansion
Ports
Description
Computers
Computers
with discrete UMA
graphics
graphics
Support for TV tuner antennas for both DVB-T and ATSC/
NTSC
√
One ExpressCard 54 slot
√
√
Digital Media Slot, supports SD, MMC, MS, MSP, xD. Supports
mini versions of SD, MMC, MS Duo with adapter (adapter is
not included)
√
√
Two Mini Card slots
√
√
●
One slot for WLAN
●
One slot for TV tuner
VGA, 15-pin supporting 1920 × 1200 resolution at 75Hz
√
VGA, 15-pin supporting 1600 × 1200 resolution at 75Hz
√
Hot Plug/Unplug and auto-detect for correct output to wideaspect vs. standard-aspect video
√
√
High-Definition Multimedia Interface (HDMI) v1.3b supporting
1080p with HDCP key
√
√
eSATA port combo with fourth USB port
√
√
Four USB 2.0 ports
√
√
IEEE 1394a
√
RJ-11 modem (select models only)
√
√
RJ-45 Ethernet
√
√
Consumer infrared
√
√
MCX connector for TV antennas (select models only)
√
√
Two stereo headphone jacks (audio-out)
√
√
Microphone input (audio-in)
√
√
AC adapter plug
√
√
Docking
Expansion port 3 supports the HP Notebook Expansion Base
and HP Notebook QuickDock
√
√
Keyboard/pointing devices
16-inch full-size keyboard with numeric keypad
√
√
Standard IMR keyboard
√
√
UV painted keyboard (select models only)
√
√
Textured (non-painted) keyboard (select models only)
√
√
TouchPad supports 2-way scrolling
√
√
Taps enabled as default
√
√
6-cell 2.55-Ah Li-ion battery with target life of 2.5 hours
√
Power requirements
6-cell 2.55-Ah Li-ion battery with target life of 3 hours
6-cell 2.20-Ah Li-ion battery with target life of 2.2 hours
4
Chapter 1 Product description
√
√
Category
Description
Computers
with discrete
graphics
6-cell 2.20-Ah Li-ion battery with target life of 2.25 hours
12-cell 8.80-Ah Li-ion battery with target life of 4 hours
√
√
12-cell 8.80-Ah Li-ion battery with target life of 5 hours
90-W AC adapter
√
√
65-W AC adapter
Security
Operating system
Serviceability
Computers
UMA
graphics
√
Security cable slot
√
√
Fingerprint reader (select models only)
√
√
Windows Vista® Business (32-bit) Service Pack 2
√
√
Windows Vista Home Basic (32-bit) Service Pack 2
√
√
Windows Vista Premium (32-bit and-64 bit) Service Pack 2
√
√
Windows Vista Ultimate (64-bit) Service Pack 2
√
√
AC adapter
√
√
Battery (system)
√
√
Hard drive
√
√
Memory module
√
√
Optical drive
√
√
Mini Card components
√
√
Preinstalled:
5
2
External component identification
Top components
TouchPad
Component
Description
(1)
●
White: TouchPad is enabled.
●
Amber: TouchPad is disabled.
TouchPad light
(2)
TouchPad*
Moves the pointer and selects or activates items on the screen.
(3)
Left TouchPad button*
Functions like the left button on an external mouse.
(4)
TouchPad on/off button
Enables/disables the TouchPad.
(5)
TouchPad vertical scroll zone
Scrolls up or down.
(6)
Right TouchPad button*
Functions like the right button on an external mouse.
*This table describes factory settings. To view and change TouchPad preferences, select Start > Control Panel > Hardware
and Sound > Mouse.
6
Chapter 2 External component identification
Lights
Component
Description
(1)
●
On: The computer is on.
●
Blinking: The computer is in the Sleep state.
●
Off: The computer is off or in Hibernation.
●
On: A battery is charging.
●
Blinking: A battery that is the only available power source has
reached a low battery level. When the battery reaches a
critical battery level, the battery light begins blinking rapidly.
●
Off: If the computer is plugged into an external power source,
the light is turned off when all batteries in the computer are
fully charged. If the computer is not plugged into an external
power source, the light stays off until the battery reaches a
low battery level.
●
Blinking: The hard drive or optical drive is being accessed.
●
Amber: HP ProtectSmart Hard Drive Protection has
temporarily parked the hard drive.
(2)
(3)
Power lights* (2)
Battery light
Drive light
(4)
Caps lock light
On: Caps lock is on.
(5)
Volume mute light
●
White: Computer sound is turned on.
●
Amber: Computer sound is turned off.
(6)
Volume down light
On: The volume scroll zone is being used to decrease speaker
volume.
(7)
Volume up light
On: The volume scroll zone is being used to increase speaker
volume.
(8)
Previous/rewind light (select models only)
On: The previous/rewind button has been pressed.
(9)
Play/pause light (select models only)
On: The play/pause button has been pressed.
(10)
Next/fast forward light (select models only)
On: The next/fast forward button has been pressed.
Top components
7
Component
Description
(11)
Stop light (select models only)
On: The stop button has been pressed.
(12)
Wireless light
●
Blue: An integrated wireless device, such as a wireless local
area network (WLAN) device and/or a Bluetooth® device, is
turned on.
●
Amber: All wireless devices are turned off.
(13)
Num lock light
On: The integrated numeric keypad is enabled, or num lock is
enabled on a connected optional numeric keypad.
*The 2 power lights display the same information. The light on the power button is visible only when the computer is open. The
power light on the front of the computer is visible whether the computer is open or closed.
8
Chapter 2 External component identification
Buttons, speakers and fingerprint reader
Component
Description
(1)
Speakers (2)
Produce sound.
(2)
Power button*
●
When the computer is off, press the button to turn on the
computer.
●
When the computer is on, press the button briefly to initiate
Sleep.
●
When the computer is in the Sleep state, press the button
briefly to exit Sleep.
●
When the computer is in Hibernation, press the button briefly
to exit Hibernation.
If the computer has stopped responding and Windows® shutdown
procedures are ineffective, press and hold the power button for at
least 5 seconds to turn off the computer.
To learn more about your power settings, select Start > Control
Panel > System and Maintenance > Power Options.
(3)
Volume mute button
Mutes and restores speaker sound.
(4)
Volume scroll zone
Adjusts speaker volume. Slide your finger to the left to decrease
volume and to the right to increase volume. You can also tap the
minus sign (-) on the scroll zone to decrease volume, or tap the
plus sign (+) on the scroll zone to increase volume.
(5)
Previous/rewind button (select models only)
●
Plays the previous track or chapter when the button is pressed
once.
●
Rewinds media when the button is pressed simultaneously
with the fn key.
(6)
Play/pause button (select models only)
Plays or pauses media.
Top components
9
Component
Description
(7)
●
Plays the next track or chapter when the button is pressed
once.
●
Fast forwards media when pressed simultaneously with the
fn key.
Next/fast forward button (select models only)
(8)
Stop button (select models only)
Stops playback.
(9)
Wireless button
Turns the wireless feature on or off, but does not create a wireless
connection.
NOTE: A wireless network must be set up in order to establish a
wireless connection.
(10)
Fingerprint reader (select models only)
Allows a fingerprint logon to Windows, instead of a password logon.
*This table describes factory settings. For information about changing factory settings, refer to the user guides located in Help
and Support.
10
Chapter 2 External component identification
Keys
Component
Description
(1)
esc key
Displays system information about your computer when pressed in
combination with the fn key.
(2)
fn key
Executes frequently used system functions when pressed in
combination with a function key or the esc key.
(3)
Windows logo key
Displays the Windows Start menu.
(4)
Windows applications key
Displays a shortcut menu for items beneath the pointer.
(5)
Integrated numeric keypad keys
Can be used like the keys on an external numeric keypad.
(6)
Function keys
Execute frequently used system functions when pressed in
combination with the fn key.
Top components
11
Front components
Component
Description
(1)
●
On: The computer is on.
●
Blinking: The computer is in the Sleep state.
●
Off: The computer is off or in Hibernation.
●
On: A battery is charging.
●
Blinking: A battery that is the only available power source has
reached a low battery level. When the battery reaches a
critical battery level, the battery light begins blinking rapidly.
●
Off: If the computer is plugged into an external power source,
the light is turned off when all batteries in the computer are
fully charged. If the computer is not plugged into an external
power source, the light stays off until the battery reaches a low
battery level.
●
Blinking: The hard drive or optical drive is being accessed.
●
Amber: HP ProtectSmart Hard Drive Protection has
temporarily parked the hard drive.
(2)
(3)
Power light
Battery light
Drive light
(4)
Consumer infrared lens
Receives a signal from the remote control.
(5)
Audio-in (microphone) jack
Connects an optional computer headset microphone, stereo array
microphone, or monaural microphone.
(6)
Audio-out (headphone) jacks (2)
Produce sound when connected to optional powered stereo
speakers, headphones, ear buds, a headset, or television audio.
NOTE: This table describes factory settings. For information about changing factory settings, refer to the user guides located
in Help and Support.
12
Chapter 2 External component identification
Rear component
Component
Description
Vent
Enables airflow to cool internal components.
NOTE: The computer fan starts up automatically to cool internal
components and prevent overheating. It is normal for the internal
fan to cycle on and off during routine operation.
Right-side components
Component
Description
(1)
Optical drive light
Blinking: The optical drive is being accessed.
(2)
Optical drive
Reads optical discs and, on select models, also writes to optical
discs.
(3)
USB ports (2)
Connect optional USB devices.
(4)
TV antenna/cable jack (select models only)
Connects a TV antenna, a digital cable device, or a satellite device
that receives standard or high-definition TV broadcasts.
(5)
RJ-11 (modem) jack (select models only)
Connects a modem cable.
(6)
Security cable slot
Attaches an optional security cable to the computer.
NOTE: The security cable is designed to act as a deterrent, but
it may not prevent the computer from being mishandled or stolen.
(7)
(8)
AC adapter light
Power connector
●
On: The computer is connected to external power.
●
Off: The computer is not connected to external power.
Connects an AC adapter.
Rear component
13
Left-side components
Component
Description
(1)
External monitor port
Connects an external VGA monitor or projector.
(2)
Expansion port 3
Connects the computer to an optional docking device or an optional
expansion product.
NOTE: The computer has only one expansion port. The term
expansion port 3 describes the type of expansion port.
(3)
RJ-45 (network) jack
Connects a network cable.
(4)
HDMI port
Connects an optional video or audio device, such as a highdefinition television, or any compatible digital or audio component.
(5)
eSATA/USB port (select models only)
Connects an optional high-performance eSATA component, such
as an eSATA external hard drive, or connects an optional USB
device.
NOTE: Depending on your computer model, the computer may
include a USB port only.
14
(6)
USB port
Connects an optional USB device.
(7)
1394 port (select models only)
Connects an optional IEEE 1394 or 1394a device, such as a
camcorder.
(8)
Digital Media Slot light
Blinking: The media card is being accessed.
(9)
ExpressCard slot
Supports optional ExpressCard/54 cards.
(10)
Digital Media Slot
Supports the following optional digital card formats:
Chapter 2 External component identification
●
Memory Stick (MS)
●
Memory Stick Pro (MSP)
●
MultiMediaCard (MMC)
●
Secure Digital (SD) Memory Card
●
xD-Picture Card (XD)
●
xD-Picture Card (XD) Type H
●
xD-Picture Card (XD) Type M
Bottom components
Component
Description
(1)
Hard drive bay
Holds the hard drive.
(2)
Vents (8)
Enable airflow to cool internal components.
NOTE: The computer fan starts up automatically to cool internal
components and prevent overheating. It is normal for the internal
fan to cycle on and off during routine operation.
(3)
Battery bay
Holds the battery.
(4)
Memory module compartment
Contains the memory module slots.
Also holds the WLAN module, TV tuner card (select models only),
and the Intel® Turbo Memory card (select models only).
CAUTION: To prevent an unresponsive system, replace the
wireless module only with a wireless module authorized for use in
the computer by the governmental agency that regulates wireless
devices in your country or region. If you replace the module and
then receive a warning message, remove the module to restore
computer functionality, and then contact technical support through
Help and Support.
(5)
Battery release latch
Releases the battery from the battery bay.
Bottom components
15
Display components
Component
Description
(1)
Internal display switch
Turns off the display and initiates Sleep if the display is closed while
the power is on.
(2)
Internal microphones (2)
Record sound.
(3)
Webcam light
On: The webcam is in use.
(4)
Integrated webcam
Records audio and video and captures still photographs.
Cleaning the display
CAUTION: To prevent permanent damage to the computer, never spray water, cleaning fluids, or
chemicals on the display.
To remove smudges and lint, frequently clean the display with a soft, damp, lint-free cloth. If the screen
requires additional cleaning, use premoistened antistatic wipes or an antistatic screen cleaner.
16
Chapter 2 External component identification
Wireless antennas (select models only)
On select computers, at least 2 antennas send and receive signals from one or more wireless devices.
NOTE: The antennas are not visible from the outside of the computer. For optimal transmission, keep
the areas immediately around the antennas free from obstructions.
To see wireless regulatory notices, refer to the section of the Regulatory, Safety and Environmental
Notices that applies to your country or region. These notices are located in Help and Support.
Wireless antennas (select models only)
17
3
Illustrated parts catalog
Service tag
When ordering parts or requesting information, provide the computer serial number and model
description provided on the service tag.
(1) Product name: This is the product name affixed to the front of the computer.
(2) Serial number (s/n): This is an alphanumeric identifier that is unique to each product.
(3) Part number/Product number (p/n): This number provides specific information about the product's
hardware components. The part number helps a service technician to determine what components and
parts are needed.
(4) Model description: This is the alphanumeric identifier used to locate documents, drivers, and support
for the computer.
(5) Warranty period: This number describes the duration of the warranty period for the computer.
18
Chapter 3 Illustrated parts catalog
Computer major components
Item
Description
Spare part number
(1)
Display assembly (includes webcam, 2 microphones, and 2 wireless antenna transceivers and cables)
16.0-inch WXGA BrightView display assemblies:
●
For use in white computers
512357-001
●
For use in black computers
512358-001
Computer major components
19
Item
Description
Spare part number
●
LED display for use in white computers
538349-001
●
LED display for use in black computers
538351-001
●
LED display for use in MTV2 artist edition computers
518771-001
16.0-inch WXGA AntiGlare display assemblies:
●
For use in white computers
518772-001
●
For use in black computers
573304-001
●
LED display assembly for use in white computers
538355-001
●
LED display assembly for use in black computers
538313-001
●
LED display assembly for use in MTV2 artist edition computers
538315-001
15.6-inch WXGA BrightView display assemblies:
●
For use in white computers
517862-001
●
For use in black computers
518775-001
●
LED display for use in white computers
538348-001
●
LED display for use in black computers
538350-001
15.6-inch WXGA AntiGlare display assemblies:
●
For use in white computers
518776-001
●
For use in black computers
518777-001
●
LED display for use in white computers
538312-001
●
LED display for use in black computers
538314-001
●
LED display for use in MTV2 artist edition computers
538354-001
NOTE: See Display assembly componentson page 26 for more information on display assembly spare part
numbers.
(2)
Switch cover (includes LED board and cable)
For use in white computers
518110-001
For use in black computers
518790-001
For use in MTV2 artist edition computers
570205-001
(3)
Power button board (includes cable)
512834-001
(4)
Keyboard (includes keyboard cable)
NOTE:
(5)
20
For a detailed list of available keyboards, see Sequential part number listing on page 31.
White painted keyboard
517864-xxx
White molded keyboard
517863-xxx
Black painted keyboard
518965-xxx
Black molded keyboard
518966-xxx
Black textured keyboard
570228-xxx
Bluetooth module
483113-001
Chapter 3 Illustrated parts catalog
Item
Description
(6)
Top cover (includes TouchPad and TouchPad buttons)
(7)
Spare part number
For use only with white computers equipped with a fingerprint reader
518109-001
For use only with white computers not equipped with a fingerprint reader
518108-001
For use only with black computers equipped with a fingerprint reader
518789-001
For use only with black computers not equipped with a fingerprint reader
518788-001
For use only with MTV2 artist edition computers
570206-001
Speaker assembly
533865-001
Plastics Kit, includes:
511890-001
(8a)
ExpressCard slot bezel
(8b)
Memory module cover
(8c)
Hard drive cover
NOTE:
See Plastics Kit on page 28 for more information.
(9)
ExpressCard module
464793-002
(10)
USB board (includes cable)
516497-001
(11)
System board (includes replacement thermal material)
For use with computers equipped with UMA graphics subsystem memory
509449-001
For use with computers equipped with discrete graphics subsystem memory with 1 GB 509450-001
of dedicated memory
For use with computers equipped with discrete graphics subsystem memory with 512
MB of dedicated memory
509451-001
For use with computers equipped with SidePort memory
570379-001
(12)
Power connector cable
533465-001
(13)
Processor (includes replacement thermal material)
AMD Turion Ultra ZM-87, 2.40-GHz with 2-MB L2 cache
572564-001
AMD Turion Ultra ZM-86, 2.40-GHz with 2-MB L2 cache
507974-001
AMD Turion Ultra ZM-85, 2.30-GHz with 2-MB L2 cache
532119-001
AMD Turion Ultra ZM-84, 2.30-GHz with 2-MB L2 cache
507975-001
AMD Turion Ultra ZM-82, 2.20-GHz with 2-MB L2 cache
507973-001
AMD Turion RM-77, 2.30-GHz with 1-MB L2 cache
572565-001
AMD Turion RM-75, 2.20-GHz with 1-MB L2 cache
532120-001
AMD Turion RM-74, 2.20-GHz with 1-MB L2 cache
507979-001
AMD Athlon QL-67, 2.20-GHz with 1-MB L2 cache
572566-001
AMD Athlon QL-65, 2.10-GHz with 1-MB L2 cache
532121-001
AMD Athlon QL-64, 2.10-GHz with 1-MB L2 cache
506053-001
AMD Sempron SI-42, 2.1-GHz with 512-KB L2 cache
508102-001
Computer major components
21
Item
Description
(14)
WLAN module
Atheros 9285G 802.11b/g WiFi Adapter for use in Canada, the Cayman Islands, Guam,
Puerto Rico, the United States, and the U.S. Virgin Islands
Spare part number
518436-001
Atheros 9285G 802.11b/g WiFi Adapter for use in Afghanistan, Albania, Algeria,
518436-002
Andorra, Angola, Antigua and Barbuda, Argentina, Armenia, Aruba, Australia, Austria,
Azerbaijan, the Bahamas, Bahrain, Barbados, Belgium, Belize, Benin, Bermuda,
Bhutan, Bosnia and Herzegovina, Botswana, Brazil, the British Virgin Islands, Brunei,
Bulgaria, Burkina Faso, Burundi, Cambodia, Cameroon, Cape Verde, the Central
African Republic, Chad, Chile, Colombia, Comoros, the Congo, Costa Rica, Croatia,
Cyprus, the Czech Republic, Djibouti, Dominica, the Dominican Republic, East Timor,
Ecuador, Egypt, El Salvador, Equatorial Guinea, Eritrea, Estonia, Ethiopia, Fiji, Finland,
France, French Guiana, Gabon, Gambia, Georgia, Germany, Ghana, Gibraltar,
Greece, Grenada, Guadeloupe, Guatemala, Guinea, Guinea-Bissau, Guyana, Haiti,
Honduras, Hong Kong, Hungary, Iceland, India, Indonesia, Ireland, Israel, Italy, the
Ivory Coast, Jamaica, Japan, Jordan, Kazakhstan, Kenya, Kiribati, Kuwait, Kyrgyzstan,
Laos, Latvia, Lebanon, Lesotho, Liberia, Liechtenstein, Lithuania, Luxembourg,
Macedonia, Madagascar, Malawi, Malaysia, the Maldives, Mali, Malta, the Marshall
Islands, Martinique, Mauritania, Mauritius, Mexico, Micronesia, Monaco, Mongolia,
Montenegro, Morocco, Mozambique, Namibia, Nauru, Nepal, the Nether Antilles, the
Netherlands, New Zealand, Nicaragua, Niger, Nigeria, Norway, Oman, Palau, Panama,
Papua New Guinea, Paraguay, the People’s Republic of China, Peru, the Philippines,
Poland, Portugal, the Republic of Moldova, Romania, Rwanda, Samoa, San Marino,
Sao Tome and Principe, Saudi Arabia, Senegal, Serbia, the Seychelles, Sierra Leone,
Singapore, Slovakia, Slovenia, the Solomon Islands, Somalia, South Africa, South
Korea, Spain, Sri Lanka, St. Kitts and Nevis, St. Lucia, St. Vincent and the Grenadines,
Suriname, Swaziland, Sweden, Switzerland, Syria, Taiwan, Tajikistan, Tanzania, Togo,
Tonga, Trinidad and Tobago, Tunisia, Turkey, Turkmenistan, Tuvalu, Uganda, the
United Arab Emirates, the United Kingdom, Uruguay, Uzbekistan, Vanuatu, Venezuela,
Vietnam, Yemen, Zaire, Zambia, and Zimbabwe
Atheros 9280AGN 802.11a/b/g/n WiFi Adapter for use in Canada, the Cayman Islands,
Guam, Puerto Rico, the United States, and the U.S. Virgin Islands
518437-001
Atheros 9280AGN 802.11a/b/g/n WiFi Adapter for use in Canada, the Cayman Islands, 518437-002
Guam, Puerto Rico, the United States, and the U.S. Virgin Islands for use in
Afghanistan, Albania, Algeria, Andorra, Angola, Antigua and Barbuda, Argentina,
Armenia, Aruba, Australia, Austria, Azerbaijan, the Bahamas, Bahrain, Barbados,
Belgium, Belize, Benin, Bermuda, Bhutan, Bosnia and Herzegovina, Botswana, Brazil,
the British Virgin Islands, Brunei, Bulgaria, Burkina Faso, Burundi, Cambodia,
Cameroon, Cape Verde, the Central African Republic, Chad, Chile, Colombia,
Comoros, the Congo, Costa Rica, Croatia, Cyprus, the Czech Republic, Djibouti,
Dominica, the Dominican Republic, East Timor, Ecuador, Egypt, El Salvador,
Equatorial Guinea, Eritrea, Estonia, Ethiopia, Fiji, Finland, France, French Guiana,
Gabon, Gambia, Georgia, Germany, Ghana, Gibraltar, Greece, Grenada, Guadeloupe,
Guatemala, Guinea, Guinea-Bissau, Guyana, Haiti, Honduras, Hong Kong, Hungary,
Iceland, India, Indonesia, Ireland, Israel, Italy, the Ivory Coast, Jamaica, Japan, Jordan,
Kazakhstan, Kenya, Kiribati, Kuwait, Kyrgyzstan, Laos, Latvia, Lebanon, Lesotho,
Liberia, Liechtenstein, Lithuania, Luxembourg, Macedonia, Madagascar, Malawi,
Malaysia, the Maldives, Mali, Malta, the Marshall Islands, Martinique, Mauritania,
Mauritius, Mexico, Micronesia, Monaco, Mongolia, Montenegro, Morocco,
Mozambique, Namibia, Nauru, Nepal, the Nether Antilles, the Netherlands, New
Zealand, Nicaragua, Niger, Nigeria, Norway, Oman, Palau, Panama, Papua New
Guinea, Paraguay, the People’s Republic of China, Peru, the Philippines, Poland,
Portugal, the Republic of Moldova, Romania, Rwanda, Samoa, San Marino, Sao Tome
and Principe, Saudi Arabia, Senegal, Serbia, the Seychelles, Sierra Leone, Singapore,
Slovakia, Slovenia, the Solomon Islands, Somalia, South Africa, South Korea, Spain,
Sri Lanka, St. Kitts and Nevis, St. Lucia, St. Vincent and the Grenadines, Suriname,
Swaziland, Sweden, Switzerland, Syria, Taiwan, Tajikistan, Tanzania, Togo, Tonga,
Trinidad and Tobago, Tunisia, Turkey, Turkmenistan, Tuvalu, Uganda, the United Arab
Emirates, the United Kingdom, Uruguay, Uzbekistan, Vanuatu, Venezuela, Vietnam,
Yemen, Zaire, Zambia, and Zimbabwe
22
Chapter 3 Illustrated parts catalog
Item
Description
Spare part number
Broadcom BCM4312 802.11b/g WLAN module for use only with computers in
Antigua and Barbuda, Barbados, Belize, Canada, the Cayman Islands, Guam,
Puerto Rico, Trinidad and Tobago, the U.S. Virgin Islands, and the United States
504593-001
Broadcom BCM4312 802.11b/g WLAN module for use only with computers in
504593-002
Afghanistan, Albania, Algeria, Andorra, Angola, Antigua and Barbuda, Argentina,
Armenia, Aruba, Australia, Austria, Azerbaijan, the Bahamas, Bahrain, Bangladesh,
Barbados, Belarus, Belgium, Belize, Benin, Bermuda, Bhutan, Bolivia,
Bosnia and Herzegovina, Botswana, Brazil, the British Virgin Islands, Brunei, Bulgaria,
Burkina Faso, Burundi, Cameroon, Cape Verde, the Central African Republic, Chad,
Chile, the People's Republic of China, Colombia, Comoros, the Congo, Costa Rica,
Croatia, Cyprus, the Czech Republic, Denmark, Djibouti, Dominica,
the Dominican Republic, East Timor, Ecuador, Egypt, El Salvador, Equitorial Guinea,
Eritrea, Estonia, Ethiopia, Fiji, Finland, France, French Guiana, Gabon, Gambia,
Georgia, Germany, Ghana, Gibraltar, Greece, Grenada, Guadeloupe, Guatemala,
Guinea, Guinea-Bissau, Guyana, Haiti, Honduras, Hong Kong, Hungary, Iceland, India,
Ireland, Israel, Italy, the Ivory Coast, Jamaica, Jordan, Kazakhstan, Kenya, Kiribati,
Kyrgyzstan, Laos, Latvia, Lebanon, Lesotho, Liberia, Liechtenstein, Lithuania,
Luxembourg, Macedonia, Madagascar, Malawi, Malaysia, the Maldives, Mali, Malta,
the Marshall Islands, Martinique, Mauritania, Mauritius, Mexico, Micronesia, Monaco,
Mongolia, Montenegro, Morocco, Mozambique, Namibia, Nauru, Nepal,
the Nether Antilles, the Netherlands, New Zealand, Nicaragua, Niger, Nigeria, Norway,
Oman, Pakistan, Palau, Panama, Papua New Guinea, Paraguay, Peru, the Philippines,
Poland, Portugal, the Republic of Moldova, Romania, Russia, Rwanda, Samoa,
San Marino, Sao Tome and Principe, Saudi Arabia, Senegal, Serbia, the Seychelles,
Sierra Leone, Singapore, Slovakia, Slovenia, the Solomon Islands, Somalia,
South Africa, South Korea, Spain, Sri Lanka, St. Kitts and Nevis, St. Lucia,
St. Vincent and the Grenadines, Suriname, Swaziland, Sweden, Switzerland, Taiwan,
Tajikistan, Tanzania, Togo, Tonga, Trinidad and Tobago, Tunisia, Turkey,
Turkmenistan, Tuvalu, Uganda, Ukraine, the United Arab Emirates,
the United Kingdom, Uruguay, Uzbekistan, Vanuatu, Venezuela, Vietnam, Yemen,
Zaire, Zambia, and Zimbabwe
Broadcom BCM4312 802.11b/g WLAN module for use only with computers in
Antigua and Barbuda, Barbados, Belize, Canada, the Cayman Islands, Guam,
Puerto Rico, Trinidad and Tobago, the U.S. Virgin Islands, and the United States
504664-001
Computer major components
23
Item
Description
Spare part number
Broadcom BCM4312 802.11b/g WLAN module for use only with computers in
504664-002
Afghanistan, Albania, Algeria, Andorra, Angola, Antigua and Barbuda, Argentina,
Armenia, Aruba, Australia, Austria, Azerbaijan, the Bahamas, Bahrain, Bangladesh,
Barbados, Belarus, Belgium, Belize, Benin, Bermuda, Bhutan, Bolivia,
Bosnia and Herzegovina, Botswana, Brazil, the British Virgin Islands, Brunei, Bulgaria,
Burkina Faso, Burundi, Cameroon, Cape Verde, the Central African Republic, Chad,
Chile, the People's Republic of China, Colombia, Comoros, the Congo, Costa Rica,
Croatia, Cyprus, the Czech Republic, Denmark, Djibouti, Dominica,
the Dominican Republic, East Timor, Ecuador, Egypt, El Salvador, Equitorial Guinea,
Eritrea, Estonia, Ethiopia, Fiji, Finland, France, French Guiana, Gabon, Gambia,
Georgia, Germany, Ghana, Gibraltar, Greece, Grenada, Guadeloupe, Guatemala,
Guinea, Guinea-Bissau, Guyana, Haiti, Honduras, Hong Kong, Hungary, Iceland, India,
Ireland, Israel, Italy, the Ivory Coast, Jamaica, Jordan, Kazakhstan, Kenya, Kiribati,
Kyrgyzstan, Laos, Latvia, Lebanon, Lesotho, Liberia, Liechtenstein, Lithuania,
Luxembourg, Macedonia, Madagascar, Malawi, Malaysia, the Maldives, Mali, Malta,
the Marshall Islands, Martinique, Mauritania, Mauritius, Mexico, Micronesia, Monaco,
Mongolia, Montenegro, Morocco, Mozambique, Namibia, Nauru, Nepal,
the Nether Antilles, the Netherlands, New Zealand, Nicaragua, Niger, Nigeria, Norway,
Oman, Pakistan, Palau, Panama, Papua New Guinea, Paraguay, Peru, the Philippines,
Poland, Portugal, the Republic of Moldova, Romania, Russia, Rwanda, Samoa,
San Marino, Sao Tome and Principe, Saudi Arabia, Senegal, Serbia, the Seychelles,
Sierra Leone, Singapore, Slovakia, Slovenia, the Solomon Islands, Somalia,
South Africa, South Korea, Spain, Sri Lanka, St. Kitts and Nevis, St. Lucia,
St. Vincent and the Grenadines, Suriname, Swaziland, Sweden, Switzerland, Taiwan,
Tajikistan, Tanzania, Togo, Tonga, Trinidad and Tobago, Tunisia, Turkey,
Turkmenistan, Tuvalu, Uganda, Ukraine, the United Arab Emirates,
the United Kingdom, Uruguay, Uzbekistan, Vanuatu, Venezuela, Vietnam, Yemen,
Zaire, Zambia, and Zimbabwe
(15)
Audio/infrared board (includes cable)
(16)
Fan/heat sink assembly (includes replacement thermal material)
(17)
511892-001
For use only with computers equipped with discrete graphics subsystems
532141-001
For use only with computers equipped with UMA graphics subsystems
532142-001
Modem module
NOTE: The modem module spare part kit does not include a modem module cable. The modem module cable is
included in the Cable Kit, spare part number 533466-001. For more information, see Cable Kit on page 29.
(18)
(19)
24
For use in all countries and regions except Australia and New Zealand
510100-001
For use only in Australia and New Zealand
510100-011
Hard drive (includes left and right bracket rails, connector cable, Mylar cover with tab, and four rubber isolators)
160-GB, 5400-rpm
537950-001
250-GB, 7200-rpm (select models only)
509412-002
250-GB, 5400-rpm
509414-002
320-GB, 7200-rpm (select models only)
509413-002
320-GB, 5400-rpm
509415-002
500-GB, 5400-rpm
509417-002
Hard Drive Hardware Kit (not illustrated, includes left and right bracket rails, connector
cable, Mylar cover with tab, and 4 rubber isolators)
483862-001
Base enclosure (includes rubber feet)
Chapter 3 Illustrated parts catalog
Item
(20)
(21)
(22)
(23)
Description
Spare part number
For use in computers with discrete graphics subsystems
532139-001
For use in computers with UMA graphics subsystems
532140-001
Rubber Feet Kit (not illustrated, includes 4 base enclosure rubber feet)
516499-001
Battery
12-cell, 95-Wh, 8.8-Ah Li-ion battery
509460-001
6-cell, 55-Wh, 2.55-Ah Li-ion battery
509459-001
6-cell, 47-Wh, 2.20-Ah Li-ion battery
509458-001
Optical drive (includes bezel and bracket)
DVD±RW and CD-RW SuperMulti Double-Layer Combo Drive
509419-002
Blu-ray ROM DVD±R/RW SuperMulti Double-Layer Drive
509420-002
Blu-ray ROM with LightScribe DVD±R/RW SuperMulti Double-Layer Drive
509421-002
Memory modules (DDR2, 800 MHz, PC2-6400, 1 DIMM):
4 GB
509409-002
2 GB
509410-002
1 GB
509411-002
TV tuner module
NOTE: The TV tuner module spare part kit does not include a TV tuner module cable. The TV tuner module cable
is included in the Cable Kit, spare part number 533466-001.
DVB-T TV tuner module (for use only with computers equipped with discrete graphics 482899-003
memory)
TV tuner external antenna cable (not illustrated)
(24)
With PAL jack
482900-002
RTC battery
449729-001
Computer major components
25
Display assembly components
The HP Pavilion dv6 Entertainment PC offers two types of display assemblies. Component spare parts
are listed in this section for AntiGlare display assemblies and BrightView display assemblies.
AntiGlare display assembly spare parts
26
Item
Description
(1)
Display enclosure (includes wireless antenna transceivers and cables)
Spare part number
For use in white computers without LED displays
517861-001
For use in black computers without LED display
518774-001
For use in white computers with LED displays
570392-001
For use in black computers with LED displays
570393-001
For use in MTV2 artist edition computers
570394-001
(2)
Webcam/microphone module (includes cable)
512827-001
(3)
Display Hinge Kit (includes left and right hinges)
For use in computers with a 16.0-inch display
513477-001
For use in computers with a 15.6-inch display
519209-001
(4)
Display inverter
488317-001
(5)
Display inverter cover
533464-001
(6)
Display cable
512825-001
Display Rubber Kit (not illustrated, includes display bezel rubber screw covers)
513479-001
Display Screw Kit (not illustrated)
512362-001
Chapter 3 Illustrated parts catalog
BrightView display assembly spare parts
Item
Description
(1)
Display bezel (includes logo and display lid switch actuator magnet)
Spare part number
For use with computers equipped with 16-inch displays
512359-001
For use with computers equipped with 15.6-inch displays
512364-001
(2)
Webcam/microphone module (includes cable)
512827-001
(3)
BrightView display panel (includes display panel cable)
(4)
For use only with computers equipped with 16-inch non-LED display panels
511868-001
For use only with computers equipped with 15.6-inch non-LED display panels
512363-001
For use only with computers equipped with 16-inch LED display panels
570094-001
For use only with computers equipped with 15.6-inch LED display panels
570095-001
Display Hinge Kit (includes left and right hinges)
For use only with computers equipped with 16-inch display panels
512360-001
For use only with computers equipped with 15.6-inch display panels
512365-001
(5)
Display inverter
488317-001
(6a)
Display cable
512825-001
(6b)
Wireless antenna cable (included with display enclosure)
(6c)
Webcam/microphone cable (included with webcam/microphone module)
Display assembly components
27
Item
Description
(7)
Display enclosure (includes wireless antenna transceivers and cables and logo LED
board and cable)
Spare part number
For use in white computers
517860-001
For use in black computers
518773-001
For use in white computers with LED displays
570390-001
For use in black computers with LED displays
570391-001
For use in MTV2 artist edition computers
573305-001
Display Rubber Kit (not illustrated, includes display bezel rubber screw covers)
512361-001
Display Screw Kit (not illustrated)
512362-001
Plastics Kit
Item
28
Description
Spare part number
Plastics Kit
511890-001
(1)
ExpressCard slot bezel
(2)
Hard drive cover (includes 2 captive screws secured by C-clips)
(3)
Memory module compartment cover (includes 3 captive screws secured by C-clips)
Chapter 3 Illustrated parts catalog
Cable Kit
Item
Description
Spare part number
Cable Kit
533466-001
(1)
Fingerprint reader cable
(2)
Audio/Infrared module cable
(3)
Modem module cable (includes RJ-11 jack)
(4)
USB cable
(5)
TV tuner module cable
Cable Kit
29
Miscellaneous parts
Description
Spare part number
Notebook sleeve, 16-inch, white
533534-001
AC adapters
65-W AC adapter
463958-001
90-W AC adapter
463955-001
Power cords:
Argentina
490371-D01
Australia and New Zealand
490371-011
Belgium, Bulgaria, the Czech Republic, Finland, France, Germany, Greece, Hungary, Iceland, the 490371-021
Netherlands, northwest Africa, Norway, Poland, Portugal, Russia, Slovakia, Spain, Sweden, and
Turkey
Brazil
490371-201
Asia/Pacific region, French Canada, Latin America, Thailand, and the United States
490371-001
Denmark
490371-081
India
490371-D61
Italy
490371-061
Japan
490371-291
South Africa
490371-AR1
South Korea
490371-AD1
Switzerland
490371-111
Taiwan
490371-AB1
The United Kingdom and Hong Kong
490371-031
Remote controls
30
Full-function remote control with teletext
465541-001
Headset, wired with volume control
371693-001
Chapter 3 Illustrated parts catalog
Description
Spare part number
Wireless laser mouse
430958-001
Screw Kit
516498-001
●
Phillips PM2.0×3.0 screws
●
Phillips PM2.0×14.0 captive screws
●
Phillips PM2.5×3.0 screws
●
Phillips PM2.5×4.0 screws
●
Phillips PM2.5×5.0 screws
●
Phillips PM2.5×5.0 captive screws
●
Phillips PM2.5×5.5 captive screws
●
Phillips PM2.5×6.5 screws
●
Phillips PM3.0×3.5 screws
Sequential part number listing
Spare part
number
Description
371693-001
Headset, wired with volume control
430958-001
Wireless laser mouse
449729-001
RTC battery
463955-001
90-W AC adapter
463958-001
65-W AC adapter
464793-002
ExpressCard module
465541-001
Full-function remote control with teletext
482899-003
DVB-T TV tuner module (for use only with computers equipped with discrete graphics memory)
482900-002
TV tuner external antenna cable with PAL jack
483113-001
Bluetooth module
483862-001
Hard Drive Hardware Kit (includes left and right bracket rails, connector cable, Mylar cover with tab, and
4 rubber isolators)
488317-001
Display inverter
489822-001
Bluetooth cable
490371-001
Power cord for use in the Asia/Pacific region, French Canada, Latin America, Thailand, and the United
States
490371-011
Power cord for use in Australia and New Zealand
490371-021
Power cord for use in Belgium, Bulgaria, the Czech Republic, Finland, France, Germany, Greece,
Hungary, Iceland, the Netherlands, northwest Africa, Norway, Poland, Portugal, Russia, Slovakia, Spain,
Sweden, and Turkey
Sequential part number listing
31
32
Spare part
number
Description
490371-031
Power cord for use in the United Kingdom and Hong Kong
490371-061
Power cord for use in Italy
490371-081
Power cord for use in Denmark
490371-111
Power cord for use in Switzerland
490371-201
Power cord for use in Brazil
490371-291
Power cord for use in Japan
490371-AB1
Power cord for use in Taiwan
490371-AD1
Power cord for use in South Korea
490371-AR1
Power cord for use in South Africa
490371-D01
Power cord for use in Argentina
490371-D61
Power cord for use in India
504593-001
Broadcom BCM4312 802.11b/g WLAN module for use only with computers in Antigua and Barbuda,
Barbados, Belize, Canada, the Cayman Islands, Guam, Puerto Rico, Trinidad and Tobago,
the U.S. Virgin Islands, and the United States
504593-002
Broadcom BCM4312 802.11b/g WLAN module for use only with computers in Afghanistan, Albania,
Algeria, Andorra, Angola, Antigua and Barbuda, Argentina, Armenia, Aruba, Australia, Austria, Azerbaijan,
the Bahamas, Bahrain, Bangladesh, Barbados, Belarus, Belgium, Belize, Benin, Bermuda, Bhutan,
Bolivia, Bosnia and Herzegovina, Botswana, Brazil, the British Virgin Islands, Brunei, Bulgaria,
Burkina Faso, Burundi, Cameroon, Cape Verde, the Central African Republic, Chad, Chile,
the People's Republic of China, Colombia, Comoros, the Congo, Costa Rica, Croatia, Cyprus,
the Czech Republic, Denmark, Djibouti, Dominica, the Dominican Republic, East Timor, Ecuador, Egypt,
El Salvador, Equitorial Guinea, Eritrea, Estonia, Ethiopia, Fiji, Finland, France, French Guiana, Gabon,
Gambia, Georgia, Germany, Ghana, Gibraltar, Greece, Grenada, Guadeloupe, Guatemala, Guinea,
Guinea-Bissau, Guyana, Haiti, Honduras, Hong Kong, Hungary, Iceland, India, Ireland, Israel, Italy,
the Ivory Coast, Jamaica, Jordan, Kazakhstan, Kenya, Kiribati, Kyrgyzstan, Laos, Latvia, Lebanon,
Lesotho, Liberia, Liechtenstein, Lithuania, Luxembourg, Macedonia, Madagascar, Malawi, Malaysia,
the Maldives, Mali, Malta, the Marshall Islands, Martinique, Mauritania, Mauritius, Mexico, Micronesia,
Monaco, Mongolia, Montenegro, Morocco, Mozambique, Namibia, Nauru, Nepal, the Nether Antilles,
the Netherlands, New Zealand, Nicaragua, Niger, Nigeria, Norway, Oman, Pakistan, Palau, Panama,
Papua New Guinea, Paraguay, Peru, the Philippines, Poland, Portugal, the Republic of Moldova,
Romania, Russia, Rwanda, Samoa, San Marino, Sao Tome and Principe, Saudi Arabia, Senegal, Serbia,
the Seychelles, Sierra Leone, Singapore, Slovakia, Slovenia, the Solomon Islands, Somalia, South Africa,
South Korea, Spain, Sri Lanka, St. Kitts and Nevis, St. Lucia, St. Vincent and the Grenadines, Suriname,
Swaziland, Sweden, Switzerland, Taiwan, Tajikistan, Tanzania, Togo, Tonga, Trinidad and Tobago,
Tunisia, Turkey, Turkmenistan, Tuvalu, Uganda, Ukraine, the United Arab Emirates, the United Kingdom,
Uruguay, Uzbekistan, Vanuatu, Venezuela, Vietnam, Yemen, Zaire, Zambia, and Zimbabwe
504664-001
Broadcom BCM4312 802.11b/g WLAN module for use only with computers in Antigua and Barbuda,
Barbados, Belize, Canada, the Cayman Islands, Guam, Puerto Rico, Trinidad and Tobago,
the U.S. Virgin Islands, and the United States
Chapter 3 Illustrated parts catalog
Spare part
number
Description
504664-002
Broadcom BCM4312 802.11b/g WLAN module for use only with computers in Afghanistan, Albania,
Algeria, Andorra, Angola, Antigua and Barbuda, Argentina, Armenia, Aruba, Australia, Austria, Azerbaijan,
the Bahamas, Bahrain, Bangladesh, Barbados, Belarus, Belgium, Belize, Benin, Bermuda, Bhutan,
Bolivia, Bosnia and Herzegovina, Botswana, Brazil, the British Virgin Islands, Brunei, Bulgaria,
Burkina Faso, Burundi, Cameroon, Cape Verde, the Central African Republic, Chad, Chile,
the People's Republic of China, Colombia, Comoros, the Congo, Costa Rica, Croatia, Cyprus,
the Czech Republic, Denmark, Djibouti, Dominica, the Dominican Republic, East Timor, Ecuador, Egypt,
El Salvador, Equitorial Guinea, Eritrea, Estonia, Ethiopia, Fiji, Finland, France, French Guiana, Gabon,
Gambia, Georgia, Germany, Ghana, Gibraltar, Greece, Grenada, Guadeloupe, Guatemala, Guinea,
Guinea-Bissau, Guyana, Haiti, Honduras, Hong Kong, Hungary, Iceland, India, Ireland, Israel, Italy,
the Ivory Coast, Jamaica, Jordan, Kazakhstan, Kenya, Kiribati, Kyrgyzstan, Laos, Latvia, Lebanon,
Lesotho, Liberia, Liechtenstein, Lithuania, Luxembourg, Macedonia, Madagascar, Malawi, Malaysia,
the Maldives, Mali, Malta, the Marshall Islands, Martinique, Mauritania, Mauritius, Mexico, Micronesia,
Monaco, Mongolia, Montenegro, Morocco, Mozambique, Namibia, Nauru, Nepal, the Nether Antilles,
the Netherlands, New Zealand, Nicaragua, Niger, Nigeria, Norway, Oman, Pakistan, Palau, Panama,
Papua New Guinea, Paraguay, Peru, the Philippines, Poland, Portugal, the Republic of Moldova,
Romania, Russia, Rwanda, Samoa, San Marino, Sao Tome and Principe, Saudi Arabia, Senegal, Serbia,
the Seychelles, Sierra Leone, Singapore, Slovakia, Slovenia, the Solomon Islands, Somalia, South Africa,
South Korea, Spain, Sri Lanka, St. Kitts and Nevis, St. Lucia, St. Vincent and the Grenadines, Suriname,
Swaziland, Sweden, Switzerland, Taiwan, Tajikistan, Tanzania, Togo, Tonga, Trinidad and Tobago,
Tunisia, Turkey, Turkmenistan, Tuvalu, Uganda, Ukraine, the United Arab Emirates, the United Kingdom,
Uruguay, Uzbekistan, Vanuatu, Venezuela, Vietnam, Yemen, Zaire, Zambia, and Zimbabwe
506053-001
AMD Athlon QL-64, 2.10-GHz processor with 1-MB L2 cache
507973-001
AMD Turion Ultra ZM-82, 2.20-GHz processor with 2-MB L2 cache
507974-001
AMD Turion Ultra ZM-86, 2.40-GHz processor with 2-MB L2 cache
507975-001
AMD Turion Ultra ZM-84, 2.30-GHz processor with 2-MB L2 cache
507979-001
AMD Turion RM-74, 2.20-GHz processor with 1-MB L2 cache
508102-001
AMD Sempron SI-42, 2.10-GHz processor with 512-KB L2 cache
509409-002
4 GB memory module (DDR2, 800-MHz, PC2-6400, 1-DIMM)
509410-002
2 GB memory module (DDR2, 800-MHz, PC2-6400, 1-DIMM)
509411-002
1 GB memory module (DDR2, 800-MHz, PC2-6400, 1-DIMM)
509412-002
250-GB, 7200-rpm hard drive (includes left and right bracket rails, connector cable, Mylar cover with tab,
and four rubber isolators) (select models only)
509413-002
320-GB, 7200-rpm hard drive (includes left and right bracket rails, connector cable, Mylar cover with tab,
and four rubber isolators) (select models only)
509414-002
250-GB, 5400-rpm hard drive (includes left and right bracket rails, connector cable, Mylar cover with tab,
and four rubber isolators)
509415-002
320-GB, 5400-rpm hard drive (includes left and right bracket rails, connector cable, Mylar cover with tab,
and four rubber isolators)
509417-002
500-GB, 5400-rpm hard drive (includes left and right bracket rails, connector cable, Mylar cover with tab,
and four rubber isolators)
509419-002
DVD±RW and CD-RW SuperMulti Double-Layer Combo Drive
509420-002
Blu-ray ROM DVD±R/RW SuperMulti Double-Layer Drive
509421-002
Blu-ray ROM with LightScribe DVD±R/RW SuperMulti Double-Layer Drive
509449-001
System board for use with computers equipped with UMA graphics subsystem memory (includes
replacement thermal material)
Sequential part number listing
33
34
Spare part
number
Description
509450-001
System board for use with computers equipped with discrete graphics subsystem memory and 1 GB of
dedicated memory (includes replacement thermal material)
509451-001
System board for use with computers equipped with discrete graphics subsystem memory and 512 MB
of dedicated memory (includes replacement thermal material)
509458-001
6-cell, 47-Wh, 2.20-Ah Li-ion battery
509459-001
6-cell, 55-Wh, 2.55-Ah Li-ion battery
509460-001
12-cell, 95-Wh, 8.8-Ah Li-ion battery
510100-001
Modem module for use in all countries and regions except Australia and New Zealand
510100-011
Modem module for use only in Australia and New Zealand
511868-001
BrightView display panel for use only with computers equipped with 16-inch non-LED display panels
(includes display panel cable)
511890-001
Plastics Kit (see Plastics Kit on page 28)
511892-001
Audio/infrared board
512357-001
16.0-inch WXGA BrightView display assembly for use in white computers (includes webcam, 2
microphones, and 2 antenna transceivers)
512358-001
16.0-inch WXGA AntiGlare display assembly for use in white computers (includes webcam, 2
microphones, and 2 antenna transceivers)
512359-001
Display bezel for use with computers equipped with 16-inch displays
512360-001
Display Hinge Kit for use only with computers equipped with 16.0-inch BrightView display panels (includes
left and right hinges)
512361-001
Display Rubber Kit for BrightView displays (includes display bezel rubber screw covers)
512362-001
Display Screw Kit
512363-001
BrightView display panel for use only with computers equipped with 15.6-inch non-LED display panels
(includes display panel cable)
512364-001
Display bezel for use with computers equipped with 15.6-inch BrightView displays (includes logo and
display lid switch actuator magnet)
512365-001
Display Hinge Kit for use only with computers equipped with 15.6-inch BrightView display panels (includes
left and right hinges)
512825-001
Display cable
512827-001
Webcam/microphone module (includes cable)
512834-001
Power button board (includes cable)
513477-001
Display Hinge Kit for 16-inch AntiGlare displays (includes left and right hinges)
513479-001
Display Rubber Kit for AntiGlare displays (includes display bezel rubber screw covers)
516497-001
USB board (includes cable)
516498-001
Screw Kit
516499-001
Rubber Feet Kit
517860-001
Display enclosure for use only with white computers equipped with BrightView display panels (includes
wireless antenna transceivers and cables and logo LED board and cable)
Chapter 3 Illustrated parts catalog
Spare part
number
Description
517861-001
Display enclosure for use in white computers equipped with AntiGlare display panels (includes wireless
antenna transceivers and cables)
517862-001
15.6-inch WXGA BrightView display assembly for use in white computers (includes webcam, 2
microphones, and 2 antenna transceivers)
517863-001
White molded keyboard for use in the United States
517863-031
White molded keyboard for use in the United Kingdom
517863-041
White molded keyboard for use in Germany
517863-051
White molded keyboard for use in France
517863-061
White molded keyboard for use in Italy
517863-071
White molded keyboard for use in Spain
517863-111
White molded keyboard for use in Switzerland
517863-131
White molded keyboard for use in Portugal
517863-141
White molded keyboard for use in Turkey
517863-161
White molded keyboard for use in Latin America
517863-201
White molded keyboard for use in Brazil
517863-211
White molded keyboard for use in Hungary
517863-251
White molded keyboard for use in Russia
517863-A41
White molded keyboard for use in Belgium
517863-AB1
White molded keyboard for use in Taiwan
517863-B31
White molded keyboard for use internationally
517863-DJ1
White molded keyboard for use in Greece
517864-001
White painted keyboard for use in the United States
517864-031
White painted keyboard for use in the United Kingdom
517864-041
White painted keyboard for use in Germany
517864-051
White painted keyboard for use in France
517864-061
White painted keyboard for use in Italy
517864-071
White painted keyboard for use in Spain
517864-111
White painted keyboard for use in Switzerland
517864-121
White painted keyboard for use in French Canada
517864-131
White painted keyboard for use in Portugal
517864-141
White painted keyboard for use in Turkey
517864-161
White painted keyboard for use in Latin America
517864-171
White painted keyboard for use in Saudi Arabia
517864-211
White painted keyboard for use in Hungary
Sequential part number listing
35
36
Spare part
number
Description
517864-221
White painted keyboard for use in the Czech Republic
517864-251
White painted keyboard for use in Russia
517864-281
White painted keyboard for use in Thailand
517864-291
White painted keyboard for use in Japan
517864-A41
White painted keyboard for use in Belgium
517864-AB1
White painted keyboard for use in Taiwan
517864-AD1
White painted keyboard for use in South Korea
517864-B31
White painted keyboard for use internationally
517864-DH1
White painted keyboard for use in the Netherlands
517864-DJ1
White painted keyboard for use in Greece
518108-001
Top cover for use only with white computers not equipped with a fingerprint reader
518109-001
Top cover for use only with white computers equipped with a fingerprint reader
518110-001
Switch cover for use in white computers (includes LED board and cable)
518436-001
Atheros 9285G 802.11b/g WiFi Adapter for use in Canada, the Cayman Islands, Guam, Puerto Rico, the
United States, and the U.S. Virgin Islands
518436-002
Atheros 9285G 802.11b/g WiFi Adapter for use in Afghanistan, Albania, Algeria, Andorra, Angola, Antigua
and Barbuda, Argentina, Armenia, Aruba, Australia, Austria, Azerbaijan, the Bahamas, Bahrain,
Barbados, Belgium, Belize, Benin, Bermuda, Bhutan, Bosnia and Herzegovina, Botswana, Brazil, the
British Virgin Islands, Brunei, Bulgaria, Burkina Faso, Burundi, Cambodia, Cameroon, Cape Verde, the
Central African Republic, Chad, Chile, Colombia, Comoros, the Congo, Costa Rica, Croatia, Cyprus, the
Czech Republic, Djibouti, Dominica, the Dominican Republic, East Timor, Ecuador, Egypt, El Salvador,
Equatorial Guinea, Eritrea, Estonia, Ethiopia, Fiji, Finland, France, French Guiana, Gabon, Gambia,
Georgia, Germany, Ghana, Gibraltar, Greece, Grenada, Guadeloupe, Guatemala, Guinea, GuineaBissau, Guyana, Haiti, Honduras, Hong Kong, Hungary, Iceland, India, Indonesia, Ireland, Israel, Italy,
the Ivory Coast, Jamaica, Japan, Jordan, Kazakhstan, Kenya, Kiribati, Kuwait, Kyrgyzstan, Laos, Latvia,
Lebanon, Lesotho, Liberia, Liechtenstein, Lithuania, Luxembourg, Macedonia, Madagascar, Malawi,
Malaysia, the Maldives, Mali, Malta, the Marshall Islands, Martinique, Mauritania, Mauritius, Mexico,
Micronesia, Monaco, Mongolia, Montenegro, Morocco, Mozambique, Namibia, Nauru, Nepal, the Nether
Antilles, the Netherlands, New Zealand, Nicaragua, Niger, Nigeria, Norway, Oman, Palau, Panama,
Papua New Guinea, Paraguay, the People’s Republic of China, Peru, the Philippines, Poland, Portugal,
the Republic of Moldova, Romania, Rwanda, Samoa, San Marino, Sao Tome and Principe, Saudi Arabia,
Senegal, Serbia, the Seychelles, Sierra Leone, Singapore, Slovakia, Slovenia, the Solomon Islands,
Somalia, South Africa, South Korea, Spain, Sri Lanka, St. Kitts and Nevis, St. Lucia, St. Vincent and the
Grenadines, Suriname, Swaziland, Sweden, Switzerland, Syria, Taiwan, Tajikistan, Tanzania, Togo,
Tonga, Trinidad and Tobago, Tunisia, Turkey, Turkmenistan, Tuvalu, Uganda, the United Arab Emirates,
the United Kingdom, Uruguay, Uzbekistan, Vanuatu, Venezuela, Vietnam, Yemen, Zaire, Zambia, and
Zimbabwe
518437-001
Atheros 9280AGN 802.11a/b/g/n WiFi Adapter for use in Canada, the Cayman Islands, Guam, Puerto
Rico, the United States, and the U.S. Virgin Islands
Chapter 3 Illustrated parts catalog
Spare part
number
Description
518437-002
Atheros 9280AGN 802.11a/b/g/n WiFi Adapter for use in Canada, the Cayman Islands, Guam, Puerto
Rico, the United States, and the U.S. Virgin Islands for use in Afghanistan, Albania, Algeria, Andorra,
Angola, Antigua and Barbuda, Argentina, Armenia, Aruba, Australia, Austria, Azerbaijan, the Bahamas,
Bahrain, Barbados, Belgium, Belize, Benin, Bermuda, Bhutan, Bosnia and Herzegovina, Botswana, Brazil,
the British Virgin Islands, Brunei, Bulgaria, Burkina Faso, Burundi, Cambodia, Cameroon, Cape Verde,
the Central African Republic, Chad, Chile, Colombia, Comoros, the Congo, Costa Rica, Croatia, Cyprus,
the Czech Republic, Djibouti, Dominica, the Dominican Republic, East Timor, Ecuador, Egypt, El Salvador,
Equatorial Guinea, Eritrea, Estonia, Ethiopia, Fiji, Finland, France, French Guiana, Gabon, Gambia,
Georgia, Germany, Ghana, Gibraltar, Greece, Grenada, Guadeloupe, Guatemala, Guinea, GuineaBissau, Guyana, Haiti, Honduras, Hong Kong, Hungary, Iceland, India, Indonesia, Ireland, Israel, Italy,
the Ivory Coast, Jamaica, Japan, Jordan, Kazakhstan, Kenya, Kiribati, Kuwait, Kyrgyzstan, Laos, Latvia,
Lebanon, Lesotho, Liberia, Liechtenstein, Lithuania, Luxembourg, Macedonia, Madagascar, Malawi,
Malaysia, the Maldives, Mali, Malta, the Marshall Islands, Martinique, Mauritania, Mauritius, Mexico,
Micronesia, Monaco, Mongolia, Montenegro, Morocco, Mozambique, Namibia, Nauru, Nepal, the Nether
Antilles, the Netherlands, New Zealand, Nicaragua, Niger, Nigeria, Norway, Oman, Palau, Panama,
Papua New Guinea, Paraguay, the People’s Republic of China, Peru, the Philippines, Poland, Portugal,
the Republic of Moldova, Romania, Rwanda, Samoa, San Marino, Sao Tome and Principe, Saudi Arabia,
Senegal, Serbia, the Seychelles, Sierra Leone, Singapore, Slovakia, Slovenia, the Solomon Islands,
Somalia, South Africa, South Korea, Spain, Sri Lanka, St. Kitts and Nevis, St. Lucia, St. Vincent and the
Grenadines, Suriname, Swaziland, Sweden, Switzerland, Syria, Taiwan, Tajikistan, Tanzania, Togo,
Tonga, Trinidad and Tobago, Tunisia, Turkey, Turkmenistan, Tuvalu, Uganda, the United Arab Emirates,
the United Kingdom, Uruguay, Uzbekistan, Vanuatu, Venezuela, Vietnam, Yemen, Zaire, Zambia, and
Zimbabwe
518771-001
16.0-inch WXGA BrightView display assembly for use in black computers (includes webcam, 2
microphones, and 2 antenna transceivers)
518772-001
16.0-inch WXGA AntiGlare display assembly for use in black computers (includes webcam, 2
microphones, and 2 antenna transceivers)
518773-001
Display enclosure for use only with black computers equipped with BrightView display panels (includes
wireless antenna transceivers and cables and logo LED board and cable)
518774-001
Display enclosure for use in black computers with AntiGlare display panels (includes wireless antenna
transceivers and cables)
518775-001
15.6-inch WXGA AntiGlare display assembly for use in white computers (includes webcam, 2
microphones, and 2 antenna transceivers)
518776-001
15.6-inch WXGA BrightView display assembly for use in black computers (includes webcam, 2
microphones, and 2 antenna transceivers)
518777-001
15.6-inch WXGA AntiGlare display assembly for use in black computers (includes webcam, 2
microphones, and 2 antenna transceivers)
518788-001
Top cover for use only with black computers not equipped with a fingerprint reader (includes TouchPad
and TouchPad buttons)
518789-001
Top cover for use only with black computers equipped with a fingerprint reader (includes TouchPad and
TouchPad buttons)
518790-001
Switch cover for use in black computers (includes LED board and cable)
518965-001
Black molded keyboard for use in the United States
518965-031
Black molded keyboard for use in the United Kingdom
518965-041
Black molded keyboard for use in Germany
518965-051
Black molded keyboard for use in France
518965-061
Black molded keyboard for use in Italy
518965-071
Black molded keyboard for use in Spain
Sequential part number listing
37
38
Spare part
number
Description
518965-111
Black molded keyboard for use in Switzerland
518965-131
Black molded keyboard for use in Portugal
518965-141
Black molded keyboard for use in Turkey
518965-161
Black molded keyboard for use in Latin America
518965-201
Black molded keyboard for use in Brazil
518965-211
Black molded keyboard for use in Hungary
518965-221
Black molded keyboard for use in the Czech Republic
518965-251
Black molded keyboard for use in Russia
518965-A41
Black molded keyboard for use internationally
518965-AB1
Black molded keyboard for use in Taiwan
518965-DJ1
Black molded keyboard for use in Greece
518966-121
Black painted keyboard for use in French Canada
518966-171
Black painted keyboard for use in Saudi Arabia
518966-281
Black painted keyboard for use in Thailand
518966-291
Black painted keyboard for use in Japan
518966-AD1
Black painted keyboard for use in South Korea
518966-DH1
Black painted keyboard for use in the Netherlands
519209-001
Display Hinge Kit for 15.6-inch AntiGlare displays (includes left and right hinges)
532119-001
AMD Turion Ultra ZM-85 2.30-GHz processor with 2-MB L2 cache
532120-001
AMD Turion RM-75 2.20-GHz processor with 1-MB L2 cache
532121-001
AMD Athlon QL-65 2.10-GHz processor with 1-MB L2 cache
532139-001
Base enclosure for use in computers with discrete graphics subsystems (includes rubber feet)
532140-001
Base enclosure for use in computers with UMA graphics subsystems (includes rubber feet)
532141-001
Fan/heat sink assembly for use only with computers equipped with graphics subsystems with discrete
graphics memory (includes replacement thermal material)
532142-001
Fan/heat sink assembly for use only with computers equipped with graphics subsystems with UMA
graphics memory (includes replacement thermal material)
533464-001
Display inverter cover for use in computers with AntiGlare displays
533465-001
Power connector cable
533466-001
Cable Kit (see Cable Kit on page 29)
533534-001
Notebook sleeve, 16-inch, white
533865-001
Speaker assembly
537950-001
160-GB, 5400-rpm hard drive (includes left and right bracket rails, connector cable, Mylar cover with tab,
and four rubber isolators) (select models only)
538312-001
15.6-inch WXGA BrightView LED display assembly for use in black computers
Chapter 3 Illustrated parts catalog
Spare part
number
Description
538313-001
16.0-inch WXGA BrightView LED display assembly for use in black computers
538314-001
15.6-inch WXGA AntiGlare LED display assembly for use in black computers
538315-001
16.0-inch WXGA AntiGlare LED display assembly for use in black computers
538348-001
15.6-inch WXGA BrightView LED display assembly for use in white computers
538349-001
16.0-inch WXGA BrightView LED display assembly for use in white computers
538350-001
15.6-inch WXGA AntiGlare LED display assembly for use in white computers
538351-001
16.0-inch WXGA AntiGlare LED display assembly for use in white computers
538354-001
15.6-inch WXGA AntiGlare LED display assembly for use in MTV2 artist edition computers
538355-001
16.0-inch WXGA AntiGlare LED display assembly for use in MTV2 artist edition computers
570094-001
BrightView display panel for use only with computers equipped with 16-inch LED display panels (includes
display panel cable)
570095-001
BrightView display panel for use only with computers equipped with 15.6-inch LED display panels
(includes display panel cable)
570205-001
Switch cover for use in MTV2 artist edition computers (includes LED board and cable)
570206-001
Top cover for use only with MTV2 artist edition computers
570228-001
Black textured keyboard for use in the United States
570228-031
Black textured keyboard for use in the United Kingdom
570228-041
Black textured keyboard for use in Germany
570228-051
Black textured keyboard for use in France
570228-061
Black textured keyboard for use in Italy
570228-071
Black textured keyboard for use in Spain
570228-111
Black textured keyboard for use in Switzerland
570228-121
Black textured keyboard for use in French Canada
570228-131
Black textured keyboard for use in Portugal
570228-141
Black textured keyboard for use in Turkey
570228-161
Black textured keyboard for use in Latin America
570228-171
Black textured keyboard for use in Saudi Arabia
570228-201
Black textured keyboard for use in Brazil
570228-211
Black textured keyboard for use in Hungary
570228-221
Black textured keyboard for use in the Czech Republic
570228-251
Black textured keyboard for use in Russia
570228-281
Black textured keyboard for use in Thailand
570228-291
Black textured keyboard for use in Japan
570228-B31
Black textured keyboard for use internationally
Sequential part number listing
39
40
Spare part
number
Description
570228-A41
Black textured keyboard for use in Belgium
570228-DJ1
Black textured keyboard for use in Greece
570228-AB1
Black textured keyboard for use in Taiwan
570228-AD1
Black textured keyboard for use in South Korea
570228-DH1
Black textured keyboard for use in the Netherlands
570379-001
System board for use with computers equipped with SidePort memory
570390-001
Display enclosure for use only with white computers equipped with BrightView LED display panels
(includes wireless antenna transceivers and cables and logo LED board and cable)
570391-001
Display enclosure for use only with black computers equipped with BrightView LED display panels
(includes wireless antenna transceivers and cables and logo LED board and cable)
570392-001
Display enclosure for use in white computers with LED displays
570393-001
Display enclosure for use in black computers with LED displays
570394-001
Display enclosure for use in MTV2 artist edition computers
572564-001
AMD Turion Ultra ZM-87, 2.40-GHz processor with 2-MB L2 cache
572565-001
AMD Turion RM-77, 2.30-GHz processor with 1-MB L2 cache
572566-001
AMD Athlon QL-67, 2.20-GHz processor with 1-MB L2 cache
573304-001
16.0-inch WXGA BrightView LED display assembly for use in MTV2 artist edition computers
573305-001
Display enclosure for use only with MTV2 artist edition computers (includes wireless antenna transceivers
and cables and logo LED board and cable)
Chapter 3 Illustrated parts catalog
4
Removal and replacement procedures
Preliminary replacement requirements
Tools required
You will need the following tools to complete the removal and replacement procedures:
●
Phillips P0 and P1 screwdrivers
●
Flat-bladed screwdriver
Service considerations
The following sections include some of the considerations that you must keep in mind during
disassembly and assembly procedures.
NOTE: As you remove each subassembly from the computer, place the subassembly (and all
accompanying screws) away from the work area to prevent damage.
Plastic parts
CAUTION: Using excessive force during disassembly and reassembly can damage plastic parts. Use
care when handling the plastic parts. Apply pressure only at the points designated in the maintenance
instructions.
Preliminary replacement requirements
41
Cables and connectors
CAUTION: When servicing the computer, be sure that cables are placed in their proper locations
during the reassembly process. Improper cable placement can damage the computer.
Cables must be handled with extreme care to avoid damage. Apply only the tension required to unseat
or seat the cables during removal and insertion. Handle cables by the connector whenever possible. In
all cases, avoid bending, twisting, or tearing cables. Be sure that cables are routed in such a way that
they cannot be caught or snagged by parts being removed or replaced. Handle flex cables with extreme
care; these cables tear easily.
Drive handling
CAUTION: Drives are fragile components that must be handled with care. To prevent damage to the
computer, damage to a drive, or loss of information, observe these precautions:
Before removing or inserting a hard drive, shut down the computer. If you are unsure whether the
computer is off or in Hibernation, turn the computer on, and then shut it down through the operating
system.
Before handling a drive, be sure that you are discharged of static electricity. While handling a drive,
avoid touching the connector.
Before removing a diskette drive or optical drive, be sure that a diskette or disc is not in the drive and
be sure that the optical drive tray is closed.
Handle drives on surfaces covered with at least one inch of shock-proof foam.
Avoid dropping drives from any height onto any surface.
After removing a hard drive, an optical drive, or a diskette drive, place it in a static-proof bag.
Avoid exposing a hard drive to products that have magnetic fields, such as monitors or speakers.
Avoid exposing a drive to temperature extremes or liquids.
If a drive must be mailed, place the drive in a bubble pack mailer or other suitable form of protective
packaging and label the package “FRAGILE.”
42
Chapter 4 Removal and replacement procedures
Grounding guidelines
Electrostatic discharge damage
Electronic components are sensitive to electrostatic discharge (ESD). Circuitry design and structure
determine the degree of sensitivity. Networks built into many integrated circuits provide some protection,
but in many cases, ESD contains enough power to alter device parameters or melt silicon junctions.
A discharge of static electricity from a finger or other conductor can destroy static-sensitive devices or
microcircuitry. Even if the spark is neither felt nor heard, damage may have occurred.
An electronic device exposed to ESD may not be affected at all and can work perfectly throughout a
normal cycle. Or the device may function normally for a while, then degrade in the internal layers,
reducing its life expectancy.
CAUTION: To prevent damage to the computer when you are removing or installing internal
components, observe these precautions:
Keep components in their electrostatic-safe containers until you are ready to install them.
Use nonmagnetic tools.
Before touching an electronic component, discharge static electricity by using the guidelines described
in this section.
Avoid touching pins, leads, and circuitry. Handle electronic components as little as possible.
If you remove a component, place it in an electrostatic-safe container.
The following table shows how humidity affects the electrostatic voltage levels generated by different
activities.
CAUTION:
A product can be degraded by as little as 700 V.
Typical electrostatic voltage levels
Relative humidity
Event
10%
40%
55%
Walking across carpet
35,000 V
15,000 V
7,500 V
Walking across vinyl floor
12,000 V
5,000 V
3,000 V
Motions of bench worker
6,000 V
800 V
400 V
Removing DIPS from plastic tube
2,000 V
700 V
400 V
Removing DIPS from vinyl tray
11,500 V
4,000 V
2,000 V
Removing DIPS from Styrofoam
14,500 V
5,000 V
3,500 V
Removing bubble pack from PCB
26,500 V
20,000 V
7,000 V
Packing PCBs in foam-lined box
21,000 V
11,000 V
5,000 V
Preliminary replacement requirements
43
Packaging and transporting guidelines
Follow these grounding guidelines when packaging and transporting equipment:
●
To avoid hand contact, transport products in static-safe tubes, bags, or boxes.
●
Protect ESD-sensitive parts and assemblies with conductive or approved containers or packaging.
●
Keep ESD-sensitive parts in their containers until the parts arrive at static-free workstations.
●
Place items on a grounded surface before removing items from their containers.
●
Always be properly grounded when touching a component or assembly.
●
Store reusable ESD-sensitive parts from assemblies in protective packaging or nonconductive
foam.
●
Use transporters and conveyors made of antistatic belts and roller bushings. Be sure that
mechanized equipment used for moving materials is wired to ground and that proper materials are
selected to avoid static charging. When grounding is not possible, use an ionizer to dissipate
electric charges.
Workstation guidelines
Follow these grounding workstation guidelines:
44
●
Cover the workstation with approved static-shielding material.
●
Use a wrist strap connected to a properly grounded work surface and use properly grounded tools
and equipment.
●
Use conductive field service tools, such as cutters, screwdrivers, and vacuums.
●
When fixtures must directly contact dissipative surfaces, use fixtures made only of static-safe
materials.
●
Keep the work area free of nonconductive materials, such as ordinary plastic assembly aids and
Styrofoam.
●
Handle ESD-sensitive components, parts, and assemblies by the case or PCM laminate. Handle
these items only at static-free workstations.
●
Avoid contact with pins, leads, or circuitry.
●
Turn off power and input signals before inserting or removing connectors or test equipment.
Chapter 4 Removal and replacement procedures
Equipment guidelines
Grounding equipment must include either a wrist strap or a foot strap at a grounded workstation.
●
When seated, wear a wrist strap connected to a grounded system. Wrist straps are flexible straps
with a minimum of one megohm ±10% resistance in the ground cords. To provide proper ground,
wear a strap snugly against the skin at all times. On grounded mats with banana-plug connectors,
use alligator clips to connect a wrist strap.
●
When standing, use foot straps and a grounded floor mat. Foot straps (heel, toe, or boot straps)
can be used at standing workstations and are compatible with most types of shoes or boots. On
conductive floors or dissipative floor mats, use foot straps on both feet with a minimum of one
megohm resistance between the operator and ground. To be effective, the conductive strips must
be worn in contact with the skin.
The following grounding equipment is recommended to prevent electrostatic damage:
●
Antistatic tape
●
Antistatic smocks, aprons, and sleeve protectors
●
Conductive bins and other assembly or soldering aids
●
Nonconductive foam
●
Conductive tabletop workstations with ground cords of one megohm resistance
●
Static-dissipative tables or floor mats with hard ties to the ground
●
Field service kits
●
Static awareness labels
●
Material-handling packages
●
Nonconductive plastic bags, tubes, or boxes
●
Metal tote boxes
●
Electrostatic voltage levels and protective materials
The following table lists the shielding protection provided by antistatic bags and floor mats.
Material
Use
Voltage protection level
Antistatic plastic
Bags
1,500 V
Carbon-loaded plastic
Floor mats
7,500 V
Metallized laminate
Floor mats
5,000 V
Preliminary replacement requirements
45
Component replacement procedures
This chapter provides removal and replacement procedures.
There are as many as 112 screws, in 11 different sizes, that must be removed, replaced, or loosened
when servicing the computer. Make special note of each screw size and location during removal and
replacement.
Service tag
When ordering parts or requesting information, provide the computer serial number and model
description provided on the service tag.
(1) Product name: This is the product name affixed to the front of the computer.
(2) Serial number (s/n): This is an alphanumeric identifier that is unique to each product.
(3) Part number/Product number (p/n): This number provides specific information about the product's
hardware components. The part number helps a service technician to determine what components and
parts are needed.
(4) Model description: This is the alphanumeric identifier used to locate documents, drivers, and support
for the computer.
(5) Warranty period: This number describes the duration of the warranty period for the computer.
46
Chapter 4 Removal and replacement procedures
Computer feet
The computer feet are adhesive-backed rubber pads. The feet are included in the Rubber Feet Kit, spare
part number 516499-001. There are 4 rubber feet that attach to the base enclosure in the locations
illustrated below.
Component replacement procedures
47
Battery
Description
Spare part number
12-cell, 95-Wh, 8.8-Ah Li-ion battery
509460-001
6-cell, 55-Wh, 2.55-Ah Li-ion battery
509459-001
6-cell, 47-Wh, 2.20-Ah Li-ion battery
509458-001
Before disassembling the computer, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
Remove the battery:
1.
Turn the computer upside down on a flat surface.
2.
Slide the battery release latch (1) to release the battery.
3.
Pivot the battery (2) upward and remove it from the computer (3).
To insert the battery, insert the rear edge of the battery into the battery bay and pivot the front edge of
the battery downward until it is seated. The battery release latch automatically locks the battery into
place.
48
Chapter 4 Removal and replacement procedures
Webcam/microphone module
NOTE: This section applies only to computers equipped with BrightView display assemblies. See
Display assemblyon page 68 for webcam/microphone module removal instructions for computers
equipped with AntiGlare display assemblies.
NOTE: If it has been determined that the webcam/microphone module is the component that must be
replaced to complete the computer repair, the display assembly does not have to be removed. Follow
the procedures in this section to replace the webcam/microphone module. For information on replacing
the display assembly and other display assembly internal components, see Display assembly
on page 68.
Description
Spare part number
Webcam/microphone module for use only with computers equipped with BrightView display
assemblies (includes cable)
512827-001
Before removing the webcam/microphone module, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 48).
Remove the webcam/microphone module:
1.
Turn the computer display-side up, with the front toward you.
2.
Open the computer as far as possible.
3.
Flex the inside edges of the top edge (1) and the left and right upper corners (2) of the display bezel
until the bezel disengages from the display enclosure.
Component replacement procedures
49
4.
Release the display bezel top edge (3) from the display enclosure.
5.
Release the webcam/microphone module (1) from the display enclosure as far as the webcam/
microphone module cable allows.
6.
Disconnect the webcam/microphone module cable (2) from the webcam/microphone module.
7.
Remove the webcam/microphone module.
Reverse this procedure to install the webcam/microphone module.
50
Chapter 4 Removal and replacement procedures
Optical drive
NOTE:
The optical drive spare part kit includes an optical drive bezel and bracket.
Description
Spare part number
Blu-ray ROM DVD±R/RW SuperMulti Double-Layer Drive
509420-002
Blu-ray ROM with LightScribe DVD±R/RW SuperMulti Double-Layer Drive
509421-002
DVD±RW and CD-RW SuperMulti Double-Layer Combo Drive
509419-002
Before removing the optical drive, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 48).
Remove the optical drive:
1.
Position the computer with the front toward you.
2.
Remove the Phillips PM2.5×6.5 screw (1) that secures the optical drive to the computer.
3.
Insert a thin tool, such as a paper clip, into the disc tray release access hole (2). (The optical drive
disc tray is partially ejected from the optical drive.)
4.
Use the disc tray frame to slide the optical drive (3) out of the computer.
5.
Remove the optical drive.
6.
If it is necessary to replace the optical drive bracket, position the optical drive with the optical drive
bracket toward you.
Component replacement procedures
51
7.
Remove the two Phillips PM2.0×3.0 screws (1) that secure the optical drive bracket to the optical
drive.
8.
Remove the optical drive bracket (2).
Reverse this procedure to reassemble and install the optical drive.
52
Chapter 4 Removal and replacement procedures
Memory module
Description
Spare part number
4 GB memory module (DDR2, 800-MHz, PC2-6400, 1-DIMM)
509409-002
2 GB memory module (DDR2, 800-MHz, PC2-6400, 1-DIMM)
509410-002
1 GB memory module (DDR2, 800-MHz, PC2-6400, 1-DIMM)
509411-001
Before removing the memory module, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 48).
Remove the memory module:
1.
Position the computer with the front toward you.
2.
Loosen the three Phillips PM2.5×5.5 captive screws (1) that secure the memory module
compartment cover to the computer.
3.
Lift the rear edge (2) of the cover, swing it up and to the front, and remove the cover (3). The
memory module compartment cover is included in the Plastics Kit, spare part number
511890-001.
4.
Spread the retaining tabs (1) on each side of the memory module slot to release the memory
module. (The edge of the module opposite the slot rises away from the computer.)
Component replacement procedures
53
5.
Remove the module (2) by pulling it away from the slot at an angle.
NOTE: Memory modules are designed with a notch (3) to prevent incorrect insertion into the
memory module slot.
Reverse this procedure to install a memory module.
54
Chapter 4 Removal and replacement procedures
TV tuner module
NOTE: The TV tuner module spare part kit does not include a TV tuner module cable. The TV tuner
module cable is included in the Cable Kit, spare part number 533466-001.
NOTE: The TV tuner external antenna cable with PAL back is available using spare part number
482900-002.
Description
Spare part number
DVB-T TV tuner module (for use only with computers equipped with discrete graphics memory)
482899-003
Before removing the TV tuner module, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC Adapter from the computer.
4.
Remove the battery (see Battery on page 48).
5.
Remove the memory module compartment cover (see Memory module on page 53).
Remove the TV tuner module:
1.
Disconnect the TV tuner module antenna cable (1) from the terminal on the TV tuner module.
2.
Remove the Phillips PM2.0×3.0 screw (2) that secures the TV tuner module to the computer.
3.
Lift the edge of the TV tuner module (3), and pull the module away from the slot at an angle.
NOTE: The TV tuner module is designed with a notch (4) to prevent incorrect insertion into the
TV tuner module slot.
Reverse this procedure to install the TV tuner module.
Component replacement procedures
55
RTC battery
Description
Spare part number
RTC battery
449729-001
Before removing the RTC battery, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 48).
5.
Remove the memory module compartment cover (see Memory module on page 53).
Remove the RTC battery:
Use a non-conductive pointed tool to pry the RTC battery from the socket on the system board.
Reverse this procedure to install the RTC battery. Be sure that the RTC battery is installed with the “+”
sign facing up.
56
Chapter 4 Removal and replacement procedures
Hard drive
NOTE: The hard drive spare part kit includes left and right bracket rails, a connector cable, Mylar cover
with tab, and 4 rubber isolators.
Description
Spare part number
160-GB, 5400-rpm
537950-001
250-GB, 7200-rpm (select models only)
509412-002
250-GB, 5400-rpm
509414-002
320-GB, 7200-rpm (select models only)
509413-002
320-GB, 5400-rpm
509415-002
500-GB, 5400-rpm
509417-002
Hard Drive Hardware Kit (includes left and right bracket rails, connector cable, Mylar cover with
tab, and 4 rubber isolators)
483862-001
Before removing the hard drive, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 48).
Remove the hard drive:
1.
Position the computer with the front toward you.
2.
Loosen the two Phillips PM2.5×5.5 captive screws (1) that secure the hard drive cover to the
computer.
Component replacement procedures
57
58
3.
Lift the right side (2) of the hard drive cover, swing it up and to the left, and remove the cover (3).
The hard drive cover is included in the Plastics Kit, spare part number 511890-001.
4.
Use the Mylar tab (1) to lift the hard drive up, and then slide it to the left (2) to release it from the
hard drive bay.
5.
Disconnect the hard drive adapter cable (3) from the system board.
6.
Remove the hard drive from the hard drive bay.
Chapter 4 Removal and replacement procedures
7.
If it is necessary to replace the hard drive bracket or any of the hard drive bracket components,
remove the following:
(1) Hard drive adapter cable
(2) Four rubber isolators
(3) Four Phillips PM3.0×3.5 screws that secure the hard drive bracket rails and Mylar cover to the
hard drive
(4) Left and right hard drive bracket rails with Mylar cover
Reverse this procedure to reassemble and install the hard drive.
Component replacement procedures
59
WLAN module
Description
Spare part number
Atheros 9285G 802.11b/g WiFi Adapter for use in Canada, the Cayman Islands, Guam, Puerto
Rico, the United States, and the U.S. Virgin Islands
518436-001
Atheros 9285G 802.11b/g WiFi Adapter for use in Afghanistan, Albania, Algeria, Andorra, Angola, 518436-002
Antigua and Barbuda, Argentina, Armenia, Aruba, Australia, Austria, Azerbaijan, the Bahamas,
Bahrain, Barbados, Belgium, Belize, Benin, Bermuda, Bhutan, Bosnia and Herzegovina,
Botswana, Brazil, the British Virgin Islands, Brunei, Bulgaria, Burkina Faso, Burundi, Cambodia,
Cameroon, Cape Verde, the Central African Republic, Chad, Chile, Colombia, Comoros, the
Congo, Costa Rica, Croatia, Cyprus, the Czech Republic, Djibouti, Dominica, the Dominican
Republic, East Timor, Ecuador, Egypt, El Salvador, Equatorial Guinea, Eritrea, Estonia, Ethiopia,
Fiji, Finland, France, French Guiana, Gabon, Gambia, Georgia, Germany, Ghana, Gibraltar,
Greece, Grenada, Guadeloupe, Guatemala, Guinea, Guinea-Bissau, Guyana, Haiti, Honduras,
Hong Kong, Hungary, Iceland, India, Indonesia, Ireland, Israel, Italy, the Ivory Coast, Jamaica,
Japan, Jordan, Kazakhstan, Kenya, Kiribati, Kuwait, Kyrgyzstan, Laos, Latvia, Lebanon, Lesotho,
Liberia, Liechtenstein, Lithuania, Luxembourg, Macedonia, Madagascar, Malawi, Malaysia, the
Maldives, Mali, Malta, the Marshall Islands, Martinique, Mauritania, Mauritius, Mexico, Micronesia,
Monaco, Mongolia, Montenegro, Morocco, Mozambique, Namibia, Nauru, Nepal, the Nether
Antilles, the Netherlands, New Zealand, Nicaragua, Niger, Nigeria, Norway, Oman, Palau,
Panama, Papua New Guinea, Paraguay, the People’s Republic of China, Peru, the Philippines,
Poland, Portugal, the Republic of Moldova, Romania, Rwanda, Samoa, San Marino, Sao Tome
and Principe, Saudi Arabia, Senegal, Serbia, the Seychelles, Sierra Leone, Singapore, Slovakia,
Slovenia, the Solomon Islands, Somalia, South Africa, South Korea, Spain, Sri Lanka, St. Kitts
and Nevis, St. Lucia, St. Vincent and the Grenadines, Suriname, Swaziland, Sweden, Switzerland,
Syria, Taiwan, Tajikistan, Tanzania, Togo, Tonga, Trinidad and Tobago, Tunisia, Turkey,
Turkmenistan, Tuvalu, Uganda, the United Arab Emirates, the United Kingdom, Uruguay,
Uzbekistan, Vanuatu, Venezuela, Vietnam, Yemen, Zaire, Zambia, and Zimbabwe
Atheros 9280AGN 802.11a/b/g/n WiFi Adapter for use in Canada, the Cayman Islands, Guam,
Puerto Rico, the United States, and the U.S. Virgin Islands
518437-001
Atheros 9280AGN 802.11a/b/g/n WiFi Adapter for use in Canada, the Cayman Islands, Guam,
518437-002
Puerto Rico, the United States, and the U.S. Virgin Islands for use in Afghanistan, Albania, Algeria,
Andorra, Angola, Antigua and Barbuda, Argentina, Armenia, Aruba, Australia, Austria, Azerbaijan,
the Bahamas, Bahrain, Barbados, Belgium, Belize, Benin, Bermuda, Bhutan, Bosnia and
Herzegovina, Botswana, Brazil, the British Virgin Islands, Brunei, Bulgaria, Burkina Faso, Burundi,
Cambodia, Cameroon, Cape Verde, the Central African Republic, Chad, Chile, Colombia,
Comoros, the Congo, Costa Rica, Croatia, Cyprus, the Czech Republic, Djibouti, Dominica, the
Dominican Republic, East Timor, Ecuador, Egypt, El Salvador, Equatorial Guinea, Eritrea, Estonia,
Ethiopia, Fiji, Finland, France, French Guiana, Gabon, Gambia, Georgia, Germany, Ghana,
Gibraltar, Greece, Grenada, Guadeloupe, Guatemala, Guinea, Guinea-Bissau, Guyana, Haiti,
Honduras, Hong Kong, Hungary, Iceland, India, Indonesia, Ireland, Israel, Italy, the Ivory Coast,
Jamaica, Japan, Jordan, Kazakhstan, Kenya, Kiribati, Kuwait, Kyrgyzstan, Laos, Latvia, Lebanon,
Lesotho, Liberia, Liechtenstein, Lithuania, Luxembourg, Macedonia, Madagascar, Malawi,
Malaysia, the Maldives, Mali, Malta, the Marshall Islands, Martinique, Mauritania, Mauritius,
Mexico, Micronesia, Monaco, Mongolia, Montenegro, Morocco, Mozambique, Namibia, Nauru,
Nepal, the Nether Antilles, the Netherlands, New Zealand, Nicaragua, Niger, Nigeria, Norway,
Oman, Palau, Panama, Papua New Guinea, Paraguay, the People’s Republic of China, Peru, the
Philippines, Poland, Portugal, the Republic of Moldova, Romania, Rwanda, Samoa, San Marino,
Sao Tome and Principe, Saudi Arabia, Senegal, Serbia, the Seychelles, Sierra Leone, Singapore,
Slovakia, Slovenia, the Solomon Islands, Somalia, South Africa, South Korea, Spain, Sri Lanka,
St. Kitts and Nevis, St. Lucia, St. Vincent and the Grenadines, Suriname, Swaziland, Sweden,
Switzerland, Syria, Taiwan, Tajikistan, Tanzania, Togo, Tonga, Trinidad and Tobago, Tunisia,
Turkey, Turkmenistan, Tuvalu, Uganda, the United Arab Emirates, the United Kingdom, Uruguay,
Uzbekistan, Vanuatu, Venezuela, Vietnam, Yemen, Zaire, Zambia, and Zimbabwe
Broadcom BCM4312 802.11b/g WLAN module for use only with computers in
Antigua and Barbuda, Barbados, Belize, Canada, the Cayman Islands, Guam, Puerto Rico,
Trinidad and Tobago, the U.S. Virgin Islands, and the United States
60
Chapter 4 Removal and replacement procedures
504593-001
Description
Spare part number
Broadcom BCM4312 802.11b/g WLAN module for use only with computers in Afghanistan,
Albania, Algeria, Andorra, Angola, Antigua and Barbuda, Argentina, Armenia, Aruba, Australia,
Austria, Azerbaijan, the Bahamas, Bahrain, Bangladesh, Barbados, Belarus, Belgium, Belize,
Benin, Bermuda, Bhutan, Bolivia, Bosnia and Herzegovina, Botswana, Brazil,
the British Virgin Islands, Brunei, Bulgaria, Burkina Faso, Burundi, Cameroon, Cape Verde,
the Central African Republic, Chad, Chile, the People's Republic of China, Colombia, Comoros,
the Congo, Costa Rica, Croatia, Cyprus, the Czech Republic, Denmark, Djibouti, Dominica,
the Dominican Republic, East Timor, Ecuador, Egypt, El Salvador, Equitorial Guinea, Eritrea,
Estonia, Ethiopia, Fiji, Finland, France, French Guiana, Gabon, Gambia, Georgia, Germany,
Ghana, Gibraltar, Greece, Grenada, Guadeloupe, Guatemala, Guinea, Guinea-Bissau, Guyana,
Haiti, Honduras, Hong Kong, Hungary, Iceland, India, Ireland, Israel, Italy, the Ivory Coast,
Jamaica, Jordan, Kazakhstan, Kenya, Kiribati, Kyrgyzstan, Laos, Latvia, Lebanon, Lesotho,
Liberia, Liechtenstein, Lithuania, Luxembourg, Macedonia, Madagascar, Malawi, Malaysia,
the Maldives, Mali, Malta, the Marshall Islands, Martinique, Mauritania, Mauritius, Mexico,
Micronesia, Monaco, Mongolia, Montenegro, Morocco, Mozambique, Namibia, Nauru, Nepal,
the Nether Antilles, the Netherlands, New Zealand, Nicaragua, Niger, Nigeria, Norway, Oman,
Pakistan, Palau, Panama, Papua New Guinea, Paraguay, Peru, the Philippines, Poland, Portugal,
the Republic of Moldova, Romania, Russia, Rwanda, Samoa, San Marino, Sao Tome and Principe,
Saudi Arabia, Senegal, Serbia, the Seychelles, Sierra Leone, Singapore, Slovakia, Slovenia,
the Solomon Islands, Somalia, South Africa, South Korea, Spain, Sri Lanka, St. Kitts and Nevis,
St. Lucia, St. Vincent and the Grenadines, Suriname, Swaziland, Sweden, Switzerland, Taiwan,
Tajikistan, Tanzania, Togo, Tonga, Trinidad and Tobago, Tunisia, Turkey, Turkmenistan, Tuvalu,
Uganda, Ukraine, the United Arab Emirates, the United Kingdom, Uruguay, Uzbekistan, Vanuatu,
Venezuela, Vietnam, Yemen, Zaire, Zambia, and Zimbabwe
504593-002
Broadcom BCM4312 802.11b/g WLAN module for use only with computers in
Antigua and Barbuda, Barbados, Belize, Canada, the Cayman Islands, Guam, Puerto Rico,
Trinidad and Tobago, the U.S. Virgin Islands, and the United States
504664-001
Broadcom BCM4312 802.11b/g WLAN module for use only with computers in Afghanistan,
Albania, Algeria, Andorra, Angola, Antigua and Barbuda, Argentina, Armenia, Aruba, Australia,
Austria, Azerbaijan, the Bahamas, Bahrain, Bangladesh, Barbados, Belarus, Belgium, Belize,
Benin, Bermuda, Bhutan, Bolivia, Bosnia and Herzegovina, Botswana, Brazil,
the British Virgin Islands, Brunei, Bulgaria, Burkina Faso, Burundi, Cameroon, Cape Verde,
the Central African Republic, Chad, Chile, the People's Republic of China, Colombia, Comoros,
the Congo, Costa Rica, Croatia, Cyprus, the Czech Republic, Denmark, Djibouti, Dominica,
the Dominican Republic, East Timor, Ecuador, Egypt, El Salvador, Equitorial Guinea, Eritrea,
Estonia, Ethiopia, Fiji, Finland, France, French Guiana, Gabon, Gambia, Georgia, Germany,
Ghana, Gibraltar, Greece, Grenada, Guadeloupe, Guatemala, Guinea, Guinea-Bissau, Guyana,
Haiti, Honduras, Hong Kong, Hungary, Iceland, India, Ireland, Israel, Italy, the Ivory Coast,
Jamaica, Jordan, Kazakhstan, Kenya, Kiribati, Kyrgyzstan, Laos, Latvia, Lebanon, Lesotho,
Liberia, Liechtenstein, Lithuania, Luxembourg, Macedonia, Madagascar, Malawi, Malaysia,
the Maldives, Mali, Malta, the Marshall Islands, Martinique, Mauritania, Mauritius, Mexico,
Micronesia, Monaco, Mongolia, Montenegro, Morocco, Mozambique, Namibia, Nauru, Nepal,
the Nether Antilles, the Netherlands, New Zealand, Nicaragua, Niger, Nigeria, Norway, Oman,
Pakistan, Palau, Panama, Papua New Guinea, Paraguay, Peru, the Philippines, Poland, Portugal,
the Republic of Moldova, Romania, Russia, Rwanda, Samoa, San Marino, Sao Tome and Principe,
Saudi Arabia, Senegal, Serbia, the Seychelles, Sierra Leone, Singapore, Slovakia, Slovenia,
the Solomon Islands, Somalia, South Africa, South Korea, Spain, Sri Lanka, St. Kitts and Nevis,
St. Lucia, St. Vincent and the Grenadines, Suriname, Swaziland, Sweden, Switzerland, Taiwan,
Tajikistan, Tanzania, Togo, Tonga, Trinidad and Tobago, Tunisia, Turkey, Turkmenistan, Tuvalu,
Uganda, Ukraine, the United Arab Emirates, the United Kingdom, Uruguay, Uzbekistan, Vanuatu,
Venezuela, Vietnam, Yemen, Zaire, Zambia, and Zimbabwe
504664-002
Before removing the WLAN module, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
Component replacement procedures
61
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 48).
5.
Remove the hard drive (see Hard drive on page 57).
Remove the WLAN module:
CAUTION: To prevent an unresponsive system, replace the wireless module only with a wireless
module authorized for use in the computer by the governmental agency that regulates wireless devices
in your country or region. If you replace the module and then receive a warning message, remove the
module to restore computer functionality, and then contact technical support through Help and Support.
1.
Disconnect the WLAN antenna cables (1) from the WLAN module.
NOTE: The black WLAN antenna cable is connected to the WLAN module “Main” terminal. The
white WLAN antenna cable is connected to the WLAN module “Aux” terminal.
2.
Remove the Phillips PM2.0×3.0 screw (2) that secures the WLAN module to the computer.
3.
Remove the WLAN module (3) by pulling it away from the slot at an angle.
NOTE: WLAN modules are designed with a notch (4) to prevent incorrect insertion into the WLAN
module slot.
Reverse this procedure to install a WLAN module.
62
Chapter 4 Removal and replacement procedures
Switch cover and keyboard
NOTE:
Only select models are equipped with media buttons on the switch cover.
Description
Spare part number
Switch cover for use in white computers (includes LED board and cable)
518110-001
Switch cover for use in black computers (includes LED board and cable)
518790-001
Switch cover for use in MTV2 artist edition computers
570205-001
Keyboards
Spare part number
White painted keyboard
517864-xxx
White molded keyboard
517863-xxx
Black painted keyboard
518966-xxx
Black molded keyboard
518965-xxx
Black textured keyboard
570228-xxx
NOTE:
For a detailed list of available keyboards, see Sequential part number listing on page 31.
Before removing the switch cover and keyboard, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 48).
Remove the switch cover and keyboard:
1.
Position the computer upside down with the front toward you.
Component replacement procedures
63
2.
Remove the following screws:
(1) Two Phillips PM2.5×6.5 screws that secure the switch cover to the computer
(2) Three Phillips PM2.5×5.0 screws that secure the switch cover to the computer (inside the battery
bay)
(3) Four Phillips PM2.5×6.5 screws that secure the keyboard to the computer
64
3.
Turn the computer display-side up, with the front toward you.
4.
Open the computer as far as possible.
5.
Lift the rear edge of the switch cover until it detaches from the computer.
Chapter 4 Removal and replacement procedures
6.
Move the switch cover back so it rests on the display.
7.
Remove the three Phillips PM2.0×3.0 screws that secure the keyboard to the computer.
8.
Lift the rear edge (1) of the keyboard.
9.
Slide the keyboard (2) back until the keyboard connector on the system board is accessible.
Component replacement procedures
65
10. Release the zero insertion force (ZIF) connector (1) to which the keyboard cable is connected and
disconnect the cable (2) from the system board.
11. Remove the keyboard.
12. Disconnect the power button board cable (1) from the low insertion force (LIF) connector on the
system board.
13. Disconnect the LED board cable (2) from the LIF connector on the system board.
14. Remove the switch cover.
Reverse this procedure to install the switch cover and keyboard.
66
Chapter 4 Removal and replacement procedures
Power button board
Description
Spare part number
Power button board (includes cable)
512834-001
Before removing the power button board, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC Adapter from the computer.
4.
Remove the battery (see Battery on page 48).
5.
Remove the switch cover and keyboard (see Switch cover and keyboard on page 63).
Remove the power button board:
1.
Turn the switch cover upside down with the front toward you.
2.
Remove the Phillips PM2.5×4.0 screw (1) that secures the power button board to the switch cover.
3.
Remove the power button board (2) and cable.
Reverse this procedure to install the power button board.
Component replacement procedures
67
Display assembly
NOTE: The display assembly includes a webcam, 2 microphones, and 2 wireless antenna transceivers
and cables.
Description
Spare part number
16.0-inch WXGA BrightView display assemblies:
Non-LED for use in white computers
512358-001
Non-LED for use in black computers
512357-001
LED for use in white computers
538349-001
LED for use in black computers
538351-001
LED for use in MTV2 artist edition computers
573304-001
16.0-inch WXGA AntiGlare display assemblies:
Non-LED for use in white computers
538355-001
Non-LED for use in black computers
518771-001
LED assembly for use in white computers
518772-001
LED assembly for use in black computers
538313-001
LED assembly for use in MTV2 artist edition computers
538315-001
15.6-inch WXGA BrightView display assemblies:
Non-LED for use in white computers
518775-001
Non_LED for use in black computers
517862-001
LED for use in white computers
538348-001
LED for use in black computers
538350-001
15.6-inch WXGA AntiGlare display assemblies:
Non LED for use in white computers
518776-001
Non-LED for use in black computers
518777-001
LED for use in white computers
538312-001
LED for use in black computers
538314-001
LED for use in MTV2 artist edition computers
538354-001
Before removing the display assembly, follow these steps:
68
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 48).
Chapter 4 Removal and replacement procedures
5.
Disconnect the wireless antenna cables from the WLAN module (see WLAN module on page 60).
6.
Remove the switch cover and keyboard (see Switch cover and keyboard on page 63).
Remove the display assembly:
1.
Disconnect the display panel cable (1) and the webcam/microphone cable (2) from the system
board.
2.
Remove the WLAN antenna cables from the clip (3) built into the top cover.
CAUTION: Support the display assembly when removing the following screws. Failure to support
the display assembly can result in damage to the display assembly and other computer
components.
3.
Remove the four Phillips PM2.5×6.5 screws (1) that secure the display assembly to the computer.
Component replacement procedures
69
4.
Remove the display assembly (2).
NOTE: Steps 5 through 27 provide display assembly internal component removal information for
computers equipped with AntiGlare display assemblies. See steps 28 through 38 for display
assembly internal component removal information for computers equipped with BrightView display
assemblies.
NOTE: See Webcam/microphone moduleon page 49 for webcam/microphone module
replacement instructions for computers equipped with BrightView display assemblies.
5.
If it is necessary to replace the display enclosure or any of the display assembly internal
components, remove the following screw covers and screws:
(1) Two plastic screw covers on the display bezel bottom edge. The display plastic screw covers
are included in the Display Rubber Kit, spare part number 513479-001.
(2) Four Phillips PM2.5×7.0 screws.
70
6.
Turn the display assembly upside down, with the bottom edge toward you.
7.
Disconnect the display assembly from the display enclosure by prying them apart from one another
along the bottom edge (1).
8.
Lift the display enclosure (2) as far as the display logo cable allows.
Chapter 4 Removal and replacement procedures
9.
Disconnect the display logo cable (3) from the display panel cable.
10. Remove the WLAN antenna cables and the webcam cable (4) from the left hinge.
NOTE:
You may have to flex the display hinge cover to remove the WLAN cables.
11. If it is necessary to replace the display inverter, remove the four Phillips PM2.5×5.0 screws (1) that
secure the display inverter cover to the display bezel. The display inverter cover is available using
spare part number 533464-001.
12. Remove the display inverter cover (2) by lifting it straight up.
NOTE:
You must remove the display inverter cover to free the antenna cables.
13. Remove the display enclosure. The display enclosure is available using spare part number
517861-001 for white computers, and 518774-001 for black computers, and includes the display
logo LED board and the wireless antenna transceivers and cables.
14. If it is necessary to replace the webcam/microphone module, remove the PM2.0x3.0 screw (1) that
secures the webcam/microphone module to the display.
Component replacement procedures
71
15. Slide the webcam/microphone module to the right, and then lift it from the display (2).
16. Disconnect the webcam/microphone module cable (3) from the webcam/microphone module.
17. Remove the webcam/microphone module. The webcam/microphone module is available using
spare part number 512827-001.
18. Disconnect the display inverter from the double-sided tape securing it to the display, and then
release the display inverter (1) as far from the display bezel as the display panel cable and backlight
cable allow.
19. Disconnect the backlight cable (2) and display panel cable (3) from the display inverter.
20. Remove the display inverter. The display inverter is available using spare part number
488317-001.
21. If it is necessary to remove the display panel cable, remove the adhesive reinforcement strip (1)
from the connector, and then disconnect the cable from the connector (2).
22. Remove the tape that secures the display panel cable to the bottom of the display (3).
72
Chapter 4 Removal and replacement procedures
23. Remove the cable from the clip on the right display hinge (4).
24. If it is necessary to replace the display hinges, remove the four Phillips PM2.5×5.0 screws (1) that
horizontally secure the display hinge bracket to the display panel.
25. Remove the four Phillips PM2.5×5.0 screws (2) that vertically secure the display hinge bracket to
the display panel.
26. Remove the display hinge bracket (3). The Display Hinge Kit is available using spare part number
513477-001 for computers with 15.6-inch displays and 519209-001 for computers with 16-inch
displays.
Component replacement procedures
73
27. If you need to remove the horizontal bracket from the vertical hinge brackets, remove the two
Phillips PM2.0×5.0 screws (1) that connect the brackets together, and then disconnect the
brackets (2).
NOTE: Steps 28 through 38 provide display assembly internal component removal information
for computers equipped with BrightView display assemblies. See steps 5 through 27 for display
assembly internal component removal information for computers equipped with AntiGlare display
assemblies.
NOTE: See Webcam/microphone moduleon page 49 for webcam/microphone module
replacement instructions for computers equipped with BrightView display assemblies.
28. If it is necessary to replace the display bezel or any of the display assembly internal components,
remove the following screw covers and screws:
(1) Two Mylar screw covers on the display bezel bottom edge. The display rubber screw covers
are included in the Display Rubber Kit, spare part number 512361-001.
(2) Two Phillips PM2.5×6.5 screws.
29. Flex the inside edges of the top edge (1), the left and right sides (2), and the bottom edge of the
display bezel (3) until the bezel disengages from the display enclosure.
74
Chapter 4 Removal and replacement procedures
30. Remove the display bezel (4). The display bezel is available using spare part number 512359-001
(16-inch display) or 512364-001 (15.6-inch display).
31. If it is necessary to replace the display inverter, disconnect the display inverter from the doublesided tape securing it to the display, and then release the display inverter (1) as far from the display
enclosure as the display panel cable and backlight cable allow.
32. Disconnect the display panel cable (2) and the backlight cable (3) from the display inverter.
33. Remove the display inverter. The display inverter is available using spare part number
488317-001.
Component replacement procedures
75
34. If it is necessary to replace the display panel, remove the two Phillips PM2.5×5.0 screws (1) from
the top corners and the six Phillips PM2.5×5.0 screws (2) from the display hinges.
35. Flex the bottom of the display panel (1) back and release the display hinges. Disconnect the display
LED cable (2) from the display panel cable. Remove the display panel (3). Display panels are
available using spare part numbers 511868-001 (16-inch non-LED display), 570094-001 (16-inch
LED display), 512363-001 (15.6-inch non-LED display), and 570095-001 (15.6-inch LED
display).
36. If it is necessary to replace the display hinges, remove the two Phillips PM2.0×3.0 screws (1) that
secure each display hinge to the display panel.
76
Chapter 4 Removal and replacement procedures
37. Remove the display hinges (2). The display hinges are available in the Display Hinge Bracket Kit,
spare part 512360-001 (16-inch display) or 512365-001 (15.6-inch display). The display hinge
screws are available in the Display Screw Kit, spare part number 512362-001.
38. If it is necessary to remove the display panel cable, remove the adhesive reinforcement strip (1)
from the display panel cable, and disconnect the display panel cable (2). Remove the tape (3) that
secures the cable to the display panel. The display panel cable is available using spare part number
512825-001.
Reverse this procedure to reassemble and install the display assembly.
Component replacement procedures
77
Speaker
Description
Spare part number
Speaker
533865-001
Before removing the speaker, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 48).
5.
Remove the following components:
a.
Hard drive (see Hard drive on page 57)
b.
Optical drive (see Optical drive on page 51)
c.
Switch cover and keyboard (see Switch cover and keyboard on page 63)
d.
Display assembly (see Display assembly on page 68)
Remove the speaker:
1.
Turn the right side up, with the front toward you.
2.
Disconnect the speaker cable from the system board (1).
3.
Remove the 5 Phillips PM2.5×6.0 screws (2) that secure the speaker to the top cover.
4.
Lift the speaker up and off the top cover (3).
Reverse this procedure to install the speaker.
78
Chapter 4 Removal and replacement procedures
Bluetooth module
NOTE: The Bluetooth module spare part kit does not include a Bluetooth module cable. The Bluetooth
module cable is available using spare part number 489822-001.
Description
Spare part number
Bluetooth module
483113-001
Before removing the Bluetooth module, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC Adapter from the computer.
4.
Remove the battery (see Battery on page 48).
5.
Remove the switch cover and keyboard (see Switch cover and keyboard on page 63).
Remove the Bluetooth module:
1.
Disconnect the Bluetooth module cable (1) from the system board.
2.
Remove the Phillips PM2.0×3.0 screw (2) that secures the Bluetooth module to the top cover.
3.
Remove the Bluetooth module from the top cover (3).
4.
Remove the Bluetooth module.
Reverse this procedure to install the Bluetooth module.
Component replacement procedures
79
Top cover
Description
Spare part number
For use only with white computers equipped with a fingerprint reader
518109-001
For use only with white computers not equipped with a fingerprint reader
518108-001
For use only with black computers equipped with a fingerprint reader
518789-001
For use only with black computers not equipped with a fingerprint reader
518788-001
For use only with MTV2 artist edition computers
570206-001
Before removing the top cover, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 48).
5.
Remove the following components:
a.
Hard drive (see Hard drive on page 57)
b.
Optical drive (see Optical drive on page 51)
c.
Switch cover and keyboard (see Switch cover and keyboard on page 63)
d.
Display assembly (see Display assembly on page 68)
Remove the top cover:
80
1.
Turn the computer upside down, with the front toward you.
2.
Remove the 10 Phillips PM2.5×7.0 screws (1) that secure the top cover to the computer.
Chapter 4 Removal and replacement procedures
3.
Remove the Phillips PM2.5×4.0 screw (2) that secures the top cover to the computer. This screw
is in the battery bay.
4.
Turn the computer right-side up, with the front toward you.
5.
Disconnect the following cables from the system board:
(1) TouchPad cable
(2) Fingerprint reader board cable
NOTE:
This cable connects to a LIF connector on the system board.
Component replacement procedures
81
6.
Remove the four Phillips PM2.5×4.0 screws that secure the top cover to the computer.
7.
Lift the rear edge (1) of the top cover until it rests at an angle.
8.
Remove the top cover (2) by lifting it straight up.
Reverse this procedure to install the top cover.
82
Chapter 4 Removal and replacement procedures
Modem module
NOTE: The modem module spare part kit does not include a modem module cable. The modem
module cable is included in the Cable Kit, spare part number 533466-001. See Cable Kit on page 29
for more Cable Kit spare part number information.
Description
Spare part number
Modem module for use in all countries and regions except Australia and New Zealand
510100-001
Modem module for use only in Australia and New Zealand
510100-011
Before removing the modem module, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC Adapter from the computer.
4.
Remove the battery (see Battery on page 48).
5.
Remove the following components:
a.
Hard drive (see Hard drive on page 57).
b.
Optical drive (see Optical drive on page 51).
c.
Switch cover and keyboard (see Switch cover and keyboard on page 63).
d.
Display assembly (see Display assembly on page 68).
e.
Top cover (see Top cover on page 80).
Remove the modem module:
1.
Disconnect the modem module cable (1) from the modem module.
2.
Remove the two Phillips PM2.5×3.0 screws (2) that secure the modem module to the system board.
Component replacement procedures
83
3.
Lift the modem module (3) straight up to disconnect it from the system board.
Reverse this procedure to install the modem module.
Audio/infrared board
Description
Spare part number
Audio/infrared board for use with computers equipped with discrete graphics memory (includes
cable)
512836-001
Audio/infrared board for use with computers equipped with UMA graphics memory (includes cable)
511892-001
Before removing the audio/infrared board, follow these steps:
84
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC Adapter from the computer.
4.
Remove the battery (see Battery on page 48).
5.
Remove the following components:
a.
Hard drive (see Hard drive on page 57).
b.
Optical drive (see Optical drive on page 51).
c.
Switch cover and keyboard (see Switch cover and keyboard on page 63).
d.
Display assembly (see Display assembly on page 68).
e.
Top cover (see Top cover on page 80).
Chapter 4 Removal and replacement procedures
Remove the audio/infrared board:
1.
Disconnect the audio/infrared board cable (1) from the LIF connector on the system board.
2.
Remove the Phillips PM2.5x7.0 screw (2) that secures the audio/infrared board to the base
enclosure.
3.
Release the clip (3) built into the base enclosure that secures the audio/infrared board.
4.
Lift the audio/infrared board (4) straight up to remove it from the base enclosure.
Reverse this procedure to install the audio/infrared board.
USB board
Description
Spare part number
USB board (includes cable)
516497-001
Before removing the USB board, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC Adapter from the computer.
4.
Remove the battery (see Battery on page 48).
5.
Remove the following components:
a.
Hard drive (see Hard drive on page 57).
b.
Optical drive (see Optical drive on page 51).
c.
Switch cover and keyboard (see Switch cover and keyboard on page 63).
Component replacement procedures
85
d.
Display assembly (see Display assembly on page 68).
e.
Top cover (see Top cover on page 80).
Remove the USB board:
1.
Disconnect the USB board cable (1) from the LIF connector on the system board.
2.
Remove the Phillips PM2.5×7.0 screw (2) that secures the USB board to the base enclosure.
3.
Remove the USB board (3) from the base enclosure.
Reverse this procedure to install the USB board.
Power connector cable
Description
Spare part number
Power connector cable
533465-001
Before removing the power connector cable, follow these steps:
86
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC Adapter from the computer.
4.
Remove the battery (see Battery on page 48).
5.
Remove the following components:
a.
Hard drive (see Hard drive on page 57).
b.
Optical drive (see Optical drive on page 51).
c.
Switch cover and keyboard (see Switch cover and keyboard on page 63).
Chapter 4 Removal and replacement procedures
d.
Display assembly (see Display assembly on page 68).
e.
Top cover (see Top cover on page 80).
f.
USB board (see USB board on page 85).
g.
System board (see System board on page 88).
Remove the power connector cable:
1.
Remove the power connector cable (1) from the clips and routing channel (2) built into the base
enclosure.
2.
Remove the Phillips PM2.5×7.0 screw (3) that secures the power connector and bracket to the
base enclosure.
3.
Remove the power connector bracket (4).
4.
Remove the power connector cable assembly (5).
Reverse this procedure to install the power connector cable.
Component replacement procedures
87
System board
NOTE:
The system board spare kit includes replacement thermal material.
Description
Spare part number
For use with computers equipped with discrete graphics subsystem memory and 1 GB of dedicated
memory
509450-001
For use with computers equipped with discrete graphics subsystem memory and 512 MB of
dedicated memory
509451-001
For use with computers equipped with UMA graphics subsystem memory
509449-001
For use with computers equipped with SidePort memory
570379-001
Before removing the system board, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 48).
5.
Remove the following components:
a.
Hard drive (see Hard drive on page 57)
b.
Optical drive (see Optical drive on page 51)
c.
Switch cover (see Switch cover and keyboard on page 63)
d.
Display assembly (see Display assembly on page 68)
e.
Top cover (see Top cover on page 80)
When replacing the system board, be sure that the following components are removed from the defective
system board and installed on the replacement system board:
●
TV tuner module (see TV tuner module on page 55)
●
RTC battery (see RTC battery on page 56)
●
Memory module (see Memory module on page 53)
●
Bluetooth module (see Bluetooth module on page 79)
●
WLAN module (see WLAN module on page 60)
●
Modem module (see Modem module on page 83)
●
Processor (see Processor on page 96)
Remove the system board:
1.
88
Disconnect the modem module cable (1) from the modem module.
Chapter 4 Removal and replacement procedures
2.
Disconnect the following cables from the system board:
(2) Audio/infrared board cable
NOTE:
The audio/infrared board cable connects to a LIF connector on the system board.
(3) USB board cable
NOTE:
The USB board cable connects to a LIF connector on the system board.
(4) Power connector cable
3.
Remove the Phillips PM2.5×7.0 screw (1) that secures the system board to the base enclosure.
4.
Lift the right side (2) of the system board until it rests at an angle.
5.
Remove the system board (3) by sliding it up and to the right at an angle.
Reverse this procedure to install the system board.
Component replacement procedures
89
TV tuner module cable
NOTE:
The TV tuner module cable is available in the Cable Kit, spare part number 533466-001.
Before removing the TV tuner module cable, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC Adapter from the computer.
4.
Remove the battery (see Battery on page 48).
5.
Remove the following components:
a.
Hard drive (see Hard drive on page 57).
b.
Optical drive (see Optical drive on page 51).
c.
Switch cover and keyboard (see Switch cover and keyboard on page 63).
d.
Display assembly (see Display assembly on page 68).
e.
Top cover (see Top cover on page 80).
f.
USB board (see USB board on page 85).
g.
System board (see System board on page 88).
Remove the TV tuner module cable:
1.
Remove the TV tuner antenna connector from the clips (1) built into the base enclosure.
2.
Remove the TV tuner module cable (2) from the clips and routing channel (3) built into the base
enclosure.
Reverse this procedure to install the TV tuner module cable.
90
Chapter 4 Removal and replacement procedures
Modem module cable
NOTE: The modem module cable is available in the Cable Kit, spare part number 533466-001. The
modem module cable includes the RJ-11 jack.
Before removing the modem module cable, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC Adapter from the computer.
4.
Remove the battery (see Battery on page 48).
5.
Remove the following components:
a.
Hard drive (see Hard drive on page 57).
b.
Optical drive (see Optical drive on page 51).
c.
Switch cover and keyboard (see Switch cover and keyboard on page 63).
d.
Display assembly (see Display assembly on page 68).
e.
Top cover (see Top cover on page 80).
f.
USB board (see USB board on page 85).
g.
System board (see System board on page 88).
Remove the modem module cable:
1.
Remove the RJ-11 jack from the clips (1) built into the base enclosure.
2.
Remove the modem module cable (2) from the clips and routing channel (3) built into the base
enclosure.
Reverse this procedure to install the modem module cable.
Component replacement procedures
91
Fan/heat sink assembly
NOTE:
The fan/heat sink assembly spare kit includes replacement thermal material.
Description
Spare part number
For use only with computers equipped with graphics subsystems with discrete memory
532141-001
For use only with computers equipped with graphics subsystems with UMA memory
532142-001
NOTE: To properly ventilate the computer, allow at least a 7.6-cm (3-inch) clearance on the right side
and rear panel of the computer. The computer uses an electric fan for ventilation. The fan is controlled
by a temperature sensor and is designed to turn on automatically when high temperature conditions
exist. These conditions are affected by high external temperatures, system power consumption, power
management/battery conservation configurations, battery fast charging, and software requirements.
Exhaust air is displaced through the ventilation grill located on the left side of the computer.
Before removing the fan/heat sink assembly, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 48).
5.
Remove the following components:
a.
Hard drive (see Hard drive on page 57).
b.
Optical drive (see Optical drive on page 51).
c.
Switch cover and keyboard (see Switch cover and keyboard on page 63).
d.
Display assembly (see Display assembly on page 68).
e.
Top cover (see Top cover on page 80).
f.
USB board (see USB board on page 85).
g.
System board (see System board on page 88).
Remove the fan/heat sink assembly:
NOTE: Steps 1 through 5 apply only to models with discrete subsystem memory on the system board.
Steps 6 through 10 apply only to models with UMA subsystem memory on the system board.
92
1.
Turn the system board upside down, with the expansion port 3 and external monitor port toward
you.
2.
Disconnect the fan cable (1) from the system board.
3.
Loosen the three Phillips PM2.5×14.0 spring-loaded, captive screws (2), (3), and (4) that secure
the fan/heat sink assembly to the system board.
Chapter 4 Removal and replacement procedures
CAUTION: Loosen the screws in the order indicated by the callouts to ensure consistent pressure
over the processor board.
4.
Loosen the three Phillips PM2.5×5.0 captive screws (5), (6), and (7) that secure the fan/heat sink
assembly to the system board.
CAUTION: Loosen the screws in the order indicated by the callouts to ensure consistent pressure
over the processor board.
5.
Remove the fan/heat sink assembly (8).
NOTE: Due to the adhesive quality of the thermal material located between the fan/heat sink
assembly and system board components, it may be necessary to move the fan/heat sink assembly
from side to side to detach the assembly.
NOTE: The thermal material must be thoroughly cleaned from the surfaces of the fan/heat sink
assembly and the system board each time the fan/heat sink assembly is removed. Thermal paste
is applied to the fan/heat sink assembly to correspond with components on the system board as
follows: capacitors and their contacts (1) the processor and contact (2), the graphics subsystem
chip and contact (3), and capacitors and their contacts (4), (5) and (6). Replacement thermal
material is included with all fan/heat sink assembly, system board, and processor spare part kits.
NOTE: Steps 1 through 5 apply only to models with discrete subsystem memory on the system
board. Steps 6 through 10 apply only to models with UMA subsystem memory on the system board.
Component replacement procedures
93
6.
Turn the system board upside down, with the expansion port 3 and external monitor port toward
you.
7.
Disconnect the fan cable (1) from the system board.
8.
Loosen the three Phillips PM2.5×14.0 spring-loaded, captive screws (2), (3), and (4) that secure
the fan/heat sink assembly to the system board.
CAUTION: Loosen the screws in the order indicated by the callouts to ensure consistent pressure
over the processor board.
9.
Loosen the two Phillips PM2.5×5.0 captive screws (5) and (6) that secure the fan/heat sink
assembly to the system board.
CAUTION: Loosen the screws in the order indicated by the callouts to ensure consistent pressure
over the processor board.
94
Chapter 4 Removal and replacement procedures
10. Remove the fan/heat sink assembly (7).
NOTE: Due to the adhesive quality of the thermal material located between the fan/heat sink
assembly and system board components, it may be necessary to move the fan/heat sink assembly
from side to side to detach the assembly.
NOTE: The thermal material must be thoroughly cleaned from the surfaces of the fan/heat sink
assembly and the system board each time the fan/heat sink assembly is removed. Thermal paste
is applied to the fan/heat sink assembly to correspond with components on the system board as
follows: capacitors and their contacts (1) the processor and contact (2), the graphics subsystem
chip and contact (3), and capacitors and their contacts (4) and (5). Replacement thermal material
is included with all fan/heat sink assembly, system board, and processor spare part kits.
Reverse this procedure to install the fan/heat sink assembly.
Component replacement procedures
95
Processor
NOTE:
The processor spare part kit includes thermal material.
Description
Spare part number
AMD Turion Ultra ZM-87, 2.40-GHz with 2-MB L2 cache
572564-001
AMD Turion Ultra ZM-86, 2.40-GHz with 2-MB L2 cache
507974-001
AMD Turion Ultra ZM-85, 2.30-GHz with 2-MB L2 cache
532119-001
AMD Turion Ultra ZM-84, 2.30-GHz with 2-MB L2 cache
507975-001
AMD Turion Ultra ZM-82, 2.20-GHz with 2-MB L2 cache
507973-001
AMD Turion RM-77, 2.30-GHz with 1-MB L2 cache
572565-001
AMD Turion RM-75, 2.20-GHz with 1-MB L2 cache
532120-001
AMD Turion RM-74, 2.20-GHz with 1-MB L2 cache
507979-001
AMD Athlon QL-67, 2.20-GHz with 1-MB L2 cache
572566-001
AMD Athlon QL-65, 2.10-GHz with 1-MB L2 cache
532121-001
AMD Athlon QL-64, 2.10-GHz with 1-MB L2 cache
506053-001
AMD Sempron SI-42, 2.1-GHz with 512-KB L2 cache
508102-001
Before removing the processor, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 48).
5.
Remove the following components:
1.
96
a.
Hard drive (see Hard drive on page 57).
b.
Optical drive (see Optical drive on page 51).
c.
Switch cover and keyboard (see Switch cover and keyboard on page 63).
d.
Display assembly (see Display assembly on page 68).
e.
Top cover (see Top cover on page 80).
f.
USB board (see USB board on page 85).
g.
System board (see System board on page 88).
h.
Fan/heat sink assembly (see Fan/heat sink assembly on page 92).
Turn the processor locking screw (1) one-half turn counterclockwise until you hear a click.
Chapter 4 Removal and replacement procedures
2.
Lift the processor (2) straight up and remove it.
NOTE: The gold triangle (3) on the processor must be aligned with the triangle icon (4) embossed
on the processor socket when you install the processor.
Reverse this procedure to install the processor.
Component replacement procedures
97
5
Setup Utility
WARNING! Only authorized technicians trained by HP must repair this equipment. All troubleshooting
and repair procedures are detailed to allow repair at only the subassembly or module level. Because of
the complexity of the individual boards and subassemblies, do not attempt to make repairs at the
component level or modify any printed wiring board. Improper repairs can create a safety hazard. Any
indication of component replacement or printed wiring board modification may void any warranty or
exchange allowances.
Starting the Setup Utility
The Setup Utility is a ROM-based information and customization utility that can be used even when your
Windows® operating system is not working.
NOTE:
The fingerprint reader (select models only) cannot be used to access the Setup Utility.
The utility reports information about the computer and provides settings for startup, security, and other
preferences.
To start the Setup Utility:
Open the Setup Utility by turning on or restarting the computer. While the “Press the ESC key for
Startup Menu” message is displayed in the lower-left corner of the screen, press f10.
– or –
98
1.
Open the Setup Utility by turning on or restarting the computer. While the “Press the ESC key for
Startup Menu” message is displayed in the lower-left corner of the screen, press esc.
2.
When the Startup Menu is displayed, press f10.
Chapter 5 Setup Utility
Using the Setup Utility
Changing the language of the Setup Utility
The following procedure explains how to change the language of the Setup Utility. If the Setup Utility is
not already running, begin at step 1. If the Setup Utility is already running, begin at step 2.
1.
Open the Setup Utility by turning on or restarting the computer. While the “Press the ESC key for
Startup Menu” message is displayed in the lower-left corner of the screen, press f10.
– or –
Open the Setup Utility by turning on or restarting the computer. While the “Press the ESC key for
Startup Menu” message is displayed in the lower-left corner of the screen, press esc. When the
Startup Menu is displayed, press f10.
2.
Use the arrow keys to select System Configuration > Language, and then press enter.
3.
Use the arrow keys to select a language, and then press enter.
4.
When a confirmation prompt with your language selected is displayed, press enter.
5.
To save your change and exit the Setup Utility, use the arrow keys to select Exit > Exit Saving
Changes, and then press enter.
Your change goes into effect immediately.
Navigating and selecting in the Setup Utility
Because the Setup Utility is not Windows based, it does not support the TouchPad. Navigation and
selection are by keystroke.
●
To choose a menu or a menu item, use the arrow keys.
●
To choose an item in a list or to toggle a field, for example an Enable/Disable field, use either the
arrow keys or f5 or f6.
●
To select an item, press enter.
●
To close a text box or return to the menu display, press esc.
●
To display additional navigation and selection information while the Setup Utility is open, press
f1.
Using the Setup Utility
99
Displaying system information
The following procedure explains how to display system information in the Setup Utility. If the Setup
Utility is not open, begin at step 1. If the Setup Utility is open, begin at step 2.
1.
Open the Setup Utility by turning on or restarting the computer. While the “Press the ESC key for
Startup Menu” message is displayed in the lower-left corner of the screen, press f10.
– or –
Open the Setup Utility by turning on or restarting the computer. While the “Press the ESC key for
Startup Menu” message is displayed in the lower-left corner of the screen, press esc. When the
Startup Menu is displayed, press f10.
2.
Select the Main menu. System information such as the system time and date, and identification
information about the computer is displayed.
3.
To exit the Setup Utility without changing any settings, use the arrow keys to select Exit > Exit
Discarding Changes, and then press enter.
Restoring default settings in the Setup Utility
The following procedure explains how to restore the Setup Utility default settings. If the Setup Utility is
not already running, begin at step 1. If the Setup Utility is already running, begin at step 2.
1.
Open the Setup Utility by turning on or restarting the computer. While the “Press the ESC key for
Startup Menu” message is displayed in the lower-left corner of the screen, press f10.
– or –
Open the Setup Utility by turning on or restarting the computer. While the “Press the ESC key for
Startup Menu” message is displayed in the lower-left corner of the screen, press esc. When the
Startup Menu is displayed, press f10.
2.
Use the arrow keys to select Exit > Load Setup Defaults, and then press enter.
3.
When the Setup Confirmation is displayed, press enter.
4.
To save your change and exit the Setup Utility, use the arrow keys to select Exit > Exit Saving
Changes, and then press enter.
The Setup Utility default settings go into effect when the computer restarts.
NOTE: Your password, security, and language settings are not changed when you restore the factory
default settings.
Exiting the Setup Utility
You can exit the Setup Utility with or without saving changes.
●
To exit the Setup Utility and save your changes from the current session:
If the Setup Utility menus are not visible, press esc to return to the menu display. Then use the
arrow keys to select Exit > Exit Saving Changes, and then press enter.
●
To exit the Setup Utility without saving your changes from the current session:
If the Setup Utility menus are not visible, press esc to return to the menu display. Then use the
arrow keys to select Exit > Exit Discarding Changes, and then press enter.
100 Chapter 5 Setup Utility
After either choice, the computer restarts in Windows.
Setup Utility menus
The menu tables in this section provide an overview of Setup Utility options.
NOTE: Some of the Setup Utility menu items listed in this chapter may not be supported by
your computer.
Main menu
Select
To do this
System information
●
View and change the system time and date.
●
View identification information about the computer.
●
View specification information about the processor, memory size,
system BIOS, and keyboard controller version (select models only).
Security menu
Select
To do this
Administrator password
Enter, change, or delete an administrator password.
Power-On Password
Enter, change, or delete a power-on password.
System Configuration menu
Select
To do this
Language Support
Change the Setup Utility language.
Button Sound (select models only)
Enable/disable the capacitive button tapping sound.
Virtualization Technology (select models only)
Enable/disable the processor Virtualization Technology.
Processor C6 State (select models only)
Enable/disable the processor C6 sleep state.
LAN Power Saving (select models only)
Enable/disable LAN Power Saving. When enabled, saves power when
the computer is in DC mode.
Card Reader/1394 Power Saving (select models
only)
Enable/disable Card Reader/1394 Power Saving.
Setup Utility menus 101
Select
To do this
Fan Always On
Enable/disable Fan Always On. When enabled, the computer fan will
always be on.
Boot Options
Set the following boot options:
●
f9 and f10 Delay (sec.)―Set the delay for the f9 and f10 functions
of the Setup Utility in intervals of 5 seconds each (0, 5, 10, 15, 20).
●
CD-ROM boot―Enable/disable boot from CD-ROM.
●
Floppy boot―Enable/disable boot from diskette.
●
Internal Network Adapter boot―Enable/disable boot from Internal
Network Adapter.
●
Boot Order―Set the boot order for:
◦
USB Floppy
◦
Internal CD/DVD ROM drive
◦
USB CD/DVD ROM drive
◦
Hard drive
◦
USB Diskette on Key
◦
USB Hard drive
◦
Network adapter
Diagnostics menu
Select
To do this
Hard Disk Self Test
Run a comprehensive self-test on the hard drive.
NOTE: On models with two hard drives, this menu option is called the
Primary Hard Disk Self Test.
Secondary Hard Disk Self Test (select models
only)
Run a comprehensive self-test on a secondary hard drive.
Memory Test
Run a diagnostic test on the system memory.
102 Chapter 5 Setup Utility
6
Specifications
Computer specifications
Metric
U.S.
Width
37.85 cm
14.9 in
Depth
25.8 cm
10.12 in
Height (front to back)
3.4
1.34
Weight – BrightView (with optical drive
and hard drive)
3.18 kg
7.00 lbs
Weight – AntiGlare (with optical drive
and hard drive)
3.31 kg
7.30 lbs
Dimensions
Input power
Operating voltage
18.5 V dc @ 3.5 A - 65 W
Operating current
3.5 A or 4.74 A
Temperature
Operating (not writing to optical disc)
0°C to 35°C
32°F to 95°F
Operating (writing to optical disc)
5°C to 35°C
41°F to 95°F
Nonoperating
-20°C to 60°C
-4°F to 140°F
Relative humidity
Operating
10% to 90%
Nonoperating
5% to 95%
Maximum altitude (unpressurized)
Operating
-15 m to 3,048 m
-50 ft to 10,000 ft
Nonoperating
-15 m to 12,192 m
-50 ft to 40,000 ft
NOTE: Applicable product safety standards specify thermal limits for plastic surfaces. The computer operates well within this
range of temperatures.
Computer specifications 103
15.6-inch, WXGA display specifications
Metric
U.S.
Height
21.0 cm
8.27 in
Width
35.9 cm
14.1 in
Diagonal
39.5 cm
15.6 in
Number of colors
Up to 262,000
Contrast ratio
500:1 (typical)
Brightness
220 nits (typical)
Dimensions
Pixel resolution
Pitch
0.255 × 0.255 mm
Format
1366 × 768
Configuration
RGB vertical stripe
Backlight
Edge lit
Character display
80 × 25
Total power consumption
6.5 W
Viewing angle
±45° horizontal, ±15° upper vertical, ±35° lower vertical (typical)
104 Chapter 6 Specifications
16.0-inch WXGA BrightView display specifications
Metric
U.S.
Height
21.4 cm
8.4 in
Width
36.5 cm
14.4 in
Diagonal
40.6 cm
16 in
Number of colors
Up to 262,000
Contrast ratio
600:1
Brightness
200 nits typical
Dimensions
Pitch resolution
Pitch
0.259 × 0.259 mm
Format
1366 × 768
Configuration
RGB vertical stripe
Backlight
Edge lit
Character display
80 × 25
Total power consumption
4.5 W
Viewing angle
±45° horizontal, ±20° upper vertical, ±45° lower vertical (typical)
16.0-inch WXGA BrightView display specifications 105
16.0-inch WXGA AntiGlare display specifications
Metric
U.S.
Height
21.4 cm
8.4 in
Width
36.5 cm
14.4 in
Diagonal
40.6 cm
16 in
Number of colors
Up to 262,000
Contrast ratio
600:1
Brightness
200 nits typical
Dimensions
Pitch resolution
Pitch
0.259 × 0.259 mm
Format
1366 × 768
Configuration
RGB vertical stripe
Backlight
Edge lit
Character display
80 × 25
Total power consumption
4.5 W
Viewing angle
±45° horizontal, ±20° upper vertical, ±45° lower vertical (typical)
106 Chapter 6 Specifications
Hard drive specifications
500-GB*
320-GB*
250-GB*
160-GB*
Height
9.5 mm
9.5 mm
9.5 mm
9.5 mm
Width
70 mm
70 mm
70 mm
70 mm
Weight
101 g
101 g
101 g
101 g
Interface type
ATA-7
ATA-7
ATA-7
ATA-7
Synchronous (maximum)
100 MB/sec
100 MB/sec
100 MB/sec
100 MB/sec
Security
ATA security
ATA security
ATA security
ATA security
Dimensions
Transfer rate
Seek times (typical read, including setting)
Single track
3 ms
3 ms
3 ms
3 ms
Average
13 ms
13 ms
13 ms
13 ms
Maximum
24 ms
24 ms
24 ms
24 ms
Logical blocks
976,773,168
625,141,400
488,397,168
312,560,640
Disc rotational speed
5400-rpm
7200-rpm and
5400-rpm
7200-rpm and
5400-rpm
5400-rpm
Operating temperature
5°C to 55°C (41°F to 131°F)
*1 GB = 1 billion bytes when referring to hard drive storage capacity. Actual accessible capacity is less. Actual drive
specifications may differ slightly.
NOTE:
Certain restrictions and exclusions apply. Contact technical support for details.
Hard drive specifications 107
Blu-ray ROM DVD±R/RW SuperMulti Double-Layer Drive
specifications
Applicable disc
Read:
Write:
CD-DA, CD+(E)G, CD-MIDI,
CD-R and CD-RW, DVD+R, DVD+R(9),
CDTEXT, CD-ROM, CD-ROM XA,
DVD+RW, DVD-R, DVD-R(9),DVD-RW,
MIXED MODE CD, CD-I, CD-I Bridge DVD-RAM
(Photo-CD, Video CD), Multisession
CD (Photo-CD, CD-EXTRA, Portfolio,
CD-R, CD-RW), CD-R, CD-RW,
DVDROM (DVD-5, DVD-9, DVD-10,
DVD-18), DVD-R, DVD-RW, DVD+R,
DVD+RW, DVD-RAM, HDROM (Single Layer), HD-ROM (Dual
Layer), HD DVD-R, HD DVD-R for
Dual Layer, HD DVD-RW, BD-ROM,
BD-R, BD-RE
Access time
CD
DVD
HD
Random
<170 ms
<170 ms
<230 ms
Cache buffer
8 MB
Data transfer rate
24X CD-ROM
3,600 KB/sec
8X DVD
10,800 KB/sec
24X CD-R
3,600 KB/sec
16X CD-RW
2,400 KB/sec
8X DVD+R
10,800 KB/sec
4X DVD+RW
5,400 KB/sec
8X DVD-R
10,800 KB/sec
4X DVD-RW
5,400 KB/sec
2.4X DVD+R(9)
2,700 KB/sec
5X DVD-RAM
6,750 KB/sec
1X BD-ROM
4,500 KB/sec
1X BD-R read
4,500 KB/sec
1X BD-RE read
4,500 KB/sec
Transfer mode
Multiword DMA Mode
108 Chapter 6 Specifications
DVD±RW SuperMulti Double-Layer Combo Drive
specifications
Applicable disc
Read:
Write:
CD-DA, CD+(E)G, CD-MIDI, CD-TEXT, CDROM, CD-ROM XA, MIXED MODE CD, CD-I,
CD-I Bridge (Photo-CD, Video CD), Multisession
CD (Photo-CD, CD-EXTRA, Portfolio, CD-R, CDRW), CD-R, CD-RW, DVD-ROM (DVD-5,
DVD-9, DVD-10, DVD-18), DVD-R, DVD-RW,
DVD+R, DVD+RW, DVD-RAM
CD-R and CD-RW
Access time
CD
DVD
Random
< 175 ms
< 230 ms
Cache buffer
2 MB
DVD+R, DVD+RW, DVD-R, DVDRW, DVD-RAM
Data transfer rate
24X CD-ROM
3,600 KB/sec
8X DVD-ROM
10,800 KB/sec
24X CD-R
3,600 KB/sec
16X CD-RW
2,400 KB/sec
8X DVD+R
10,800 KB/sec
4X DVD+RW
5,400 KB/sec
8X DVD-R
10,800 KB/sec
4X DVD-RW
5,400 KB/sec
2.4X DVD+R(9)
2,700 KB/sec
5X DVD-RAM
6,750 KB/sec
Transfer mode
Multiword DMA Mode
DVD±RW SuperMulti Double-Layer Combo Drive specifications 109
System DMA specifications
Hardware DMA
System function
DMA0
Not applicable
DMA1*
Not applicable
DMA2*
Not applicable
DMA3
Not applicable
DMA4
Direct memory access controller
DMA5*
Available for PC Card
DMA6
Not assigned
DMA7
Not assigned
*ExpressCard controller can use DMA 1, 2, or 5.
110 Chapter 6 Specifications
System interrupt specifications
Hardware IRQ
System function
IRQ0
System timer
IRQ1
Standard 101-/102-Key or Microsoft® Natural Keyboard
IRQ2
Cascaded
IRQ3
Intel 82801 DB/DBM USB2 Enhanced Host Controller—24CD
IRQ4
COM1
IRQ5*
Conexant AC—Link Audio Intel 82801 DB/DBM SMBus Controller—24C3 Data Fax
Modem with SmartCP
IRQ6
Diskette drive
IRQ7*
Parallel port
IRQ8
System CMOS/real-time clock
IRQ9*
Microsoft ACPI-compliant system
IRQ10*
Intel USB UHCI controller—24C2
Intel 82852/82855 GM/GME Graphic Controller
Realtek RTL8139 Family PCI Fast Ethernet Controller
IRQ11
Intel USB EHCI controller—24CD
Intel USB UHCI controller—24C4
Intel USB UHCI controller—24C7
Intel Pro/Wireless 2200BG
TI OHCI 1394 host controller
TI PCI1410 CardBus controller
IRQ12
Synaptics PS/2 TouchPad
IRQ13
Numeric data processor
IRQ14
Primary IDE channel
IRQ15
Secondary IDE channel
*Default configuration; audio possible configurations are IRQ5, IRQ7, IRQ9, IRQ10, or none.
NOTE: ExpressCards may assert IRQ3, IRQ4, IRQ5, IRQ7, IRQ9, IRQ10, IRQ11, or IRQ15. Either the infrared or the serial
port may assert IRQ3 or IRQ4.
System interrupt specifications 111
System I/O address specifications
I/O address (hex)
System function (shipping configuration)
00-1F
DMA Controller Channel 0-3
CF7
PCI Bus on MS ACPI-Compliant System
20 - 21
Programmable Interrupt Controller (Master Controller)
24 - 25
Programmable Interrupt Controller (Aliases)
28 - 29
Programmable Interrupt Controller (Aliases)
2C - 2D
Programmable Interrupt Controller (Aliases)
2E -2F
M/B Resource (LPC Controller)
30 - 31
Programmable Interrupt Controller (Aliases)
34 - 35
Programmable Interrupt Controller (Aliases)
38 - 39
Programmable Interrupt Controller (Aliases)
3C - 3D
Programmable Interrupt Controller (Aliases)
40 - 43
System Timer
4E - 4F
M/B Resource (LPC Controller)
50 - 53
System Timer
60
EC
61
LPC
62
EC
63
LPC
64
EC
65
LPC
66
EC
67
LPC
70 - 77
System CMOS/Real Time Clock
81 - 91
DMA Controller Channel 2
92
LPC
A0 - A1
Programmable Interrupt Controller (Slave Controller)
A4 - A5
Programmable Interrupt Controller (Aliases)
A8 - A9
Programmable Interrupt Controller (Aliases)
AC - AD
Programmable Interrupt Controller (Aliases)
B0 - B1
Programmable Interrupt Controller (Aliases)
B2 - B3
LPC
B4 - B5
Programmable Interrupt Controller (Aliases)
B8 - B9
Programmable Interrupt Controller (Aliases)
112 Chapter 6 Specifications
I/O address (hex)
System function (shipping configuration)
BC - BD
Programmable Interrupt Controller (Aliases)
C0 - DF
DMA Controller Channel 4-7
F0
Numeric data processor
380 - 383
ENE CIR Receiver
384 - 38E
EC
3B0 - 3BB
VGA
3C0 - 3DF
VGA
400 - 47F
LPC
4D0 - 4D1
Programmable Interrupt Controller
500 - 53F
LPC
600 - 60F
LPC
610
LPC
800 - 80F
LPC
810 - 817
LPC
820 - 823
LPC
D00 - FFFF
PCI Bus on MS ACPI-Compliant System
164E - 164F
LPC
2000 - 2FFF
ICH9 Family PCI Express Root Port 6 (B0/D28/F5)
3000 - 3FFF
ICH9 Family PCI Express Root Port 5 (B0/D28/F4)
4000 - 4FFF
ICH9 Family PCI Express Root Port 4 (B0/D28/F3)
5000 - 50FF
Realtek RTL8168C/8111C PCI-E Gigabit Ethernic NIC (B3/D0/F0)
6000 - 6FFF
ICH9 Family PCI Express Root Port 1 (B0/D28/F0)
7000 - 70FF
VGA
7000 - 7FFF
PCI-E Root Port (B0/D1/F0)
8000 - 801F
SMBus Controller
8020 - 803F
SATA AHCI Controller - 2929
8040 - 805F
USB UHCI Controller - 2939
8060 - 807F
USB UHCI Controller - 2936
8080 - 809F
USB UHCI Controller - 2935
80A0 - 80BF
USB UHCI Controller - 2934
80C0 - 80DF
USB UHCI Controller - 3938
80E0 - 80FF
USB UHCI Controller - 2937
8100 - 8117
SATA AHCI Controller - 2929
System I/O address specifications 113
System memory map specifications
Size
Memory address
System function
640 KB
00000000-0009FFFF
Base memory
128 KB
000A0000-000BFFFF
Video memory
48 KB
000C0000-000CBFFF
Video BIOS
160 KB
000C8000-000E7FFF
Unused
64 KB
000E8000-000FFFFF
System BIOS
15 MB
00100000-00FFFFFF
Extended memory
58 MB
04800000-07FFFFFF
Super extended memory
58 MB
04800000-07FFFFFF
Unused
2 MB
08000000-080FFFFF
Video memory (direct access)
4 GB
08200000-FFFEFFFF
Unused
64 KB
FFFF0000-FFFFFFFF
System BIOS
114 Chapter 6 Specifications
7
Screw listing
This section provides specification and reference information for the screws used in the computer. All
screws listed in this section are available in the Screw Kit, spare part number 516498-001, or the Display
Screw Kit, spare part number 512362-001.
115
Phillips PM2.0×3.0 screw
Color
Quantity
Length
Thread
Head diameter
Silver
23
3.0 mm
2.0 mm
4.5 mm
Where used: One screw that secures the Bluetooth module to the top cover.
Where used: 2 screws that secure the optical drive bracket to the computer.
116 Chapter 7 Screw listing
Where used: 3 screws that secure the keyboard to the computer
Where used:
(1) One screw that secures the WLAN module to the system board
(2) One screw that secures the TV tuner module to the system board
Phillips PM2.0×3.0 screw 117
Where used: 4 screws that secure the display hinges to the display bezel on computers equipped with
BrightView display assemblies
Where used: 8 screws that secure the display hinges to the display bezel on computers equipped with
AntiGlare display assemblies
Where used: 2 screws that secure the wireless antennas to the display cover on computers equipped
with BrightView display assemblies
Where used: One screw that secures the webcam to the display cover on computers equipped with
AntiGlare display assemblies
118 Chapter 7 Screw listing
Phillips PM2.0×14.0 captive screw
Color
Quantity
Length
Thread
Head diameter
Silver
6
14.0 mm
2.0 mm
4.5 mm
Where used: 3 screws (secured by C-clips) that secure the discrete fan and heat sink to the system
board
Phillips PM2.0×14.0 captive screw 119
Where used: 3 screws (secured by C-clips) that secure the UMA fan and heat sink to the system board
120 Chapter 7 Screw listing
Phillips PM2.5×3.0 screw
Color
Quantity
Length
Thread
Head diameter
Black
2
3.0 mm
2.5 mm
4.5 mm
Where used: 2 screws that secure the modem module to the system board
Phillips PM2.5×3.0 screw 121
Phillips PM2.5×4.0 screw
Color
Quantity
Length
Thread
Head diameter
Black
17
4.0 mm
2.5 mm
4.5 mm
Where used: 3 screws that secure the switch cover to the keyboard
Where used: One screw that secures the power button board to the switch cover
122 Chapter 7 Screw listing
Where used: One screw that secures the top cover to the computer
Where used: 4 screws that secure the top cover to the computer
Where used: 8 screws that secure the display panel on computers equipped with BrightView display
assemblies
Phillips PM2.5×4.0 screw 123
Phillips PM2.5×6.0 screw
Color
Quantity
Length
Thread
Head diameter
Black
5
6.0 mm
2.5 mm
4.5 mm
Where used: 5 screws that secure the speaker to the top cover
124 Chapter 7 Screw listing
Phillips PM2.0×2.0 broadhead screw
Color
Quantity
Length
Thread
Head diameter
Black
1
2.0 mm
2.0 mm
7.0 mm
Where used: One screw that secures the fingerprint reader board to the top cover
Phillips PM2.0×2.0 broadhead screw 125
Phillips PM2.5×5.0 screw
Color
Quantity
Length
Thread
Head diameter
Black
18
5.0 mm
2.5 mm
4.4 mm
Where used: 4 screws that secure the display inverter cover to the display bezel on computers equipped
with AntiGlare display assemblies
Where used: 2 screws that secure the display hinge bracket to the display bezel on computers equipped
with AntiGlare display assemblies
126 Chapter 7 Screw listing
Where used: 4 screws that secure the display enclosure to the display bezel on computers equipped
with AntiGlare display assemblies
Where used: 8 screws that secure the display panel brackets to the display panel enclosure
Phillips PM2.5×5.0 screw 127
Phillips PM2.5×5.0 captive screw
Color
Quantity
Length
Thread
Head diameter
Black
5
5.0 mm
2.5 mm
4.5 mm
Where used: 3 screws (secured by C-clips) that secure the discrete fan and heat sink to the system
board
128 Chapter 7 Screw listing
Where used: 2 screws (secured by C-clips) that secure the UMA fan and heat sink to the system board
Phillips PM2.5×5.0 captive screw 129
Phillips PM2.5×5.5 captive screw
Color
Quantity
Length
Thread
Head diameter
Black
5
5.5 mm
2.5 mm
4.4 mm
Where used:
(1) 3 captive screws that secure the memory module compartment cover to the computer (screws are
secured by C-clips)
(2) 2 captive screws that secure the hard drive cover to the computer (screws are secured by C-clips)
130 Chapter 7 Screw listing
Phillips PM2.5×7.0 screw
Color
Quantity
Length
Thread
Head diameter
Black
26
7.0 mm
2.5 mm
4.4 mm
Where used:
(1) One screw that secures the USB board to the system board
(2) One screw that secures the system board to the computer
(3) One screw that secures the audio/infrared board to the computer
Phillips PM2.5×7.0 screw 131
Where used: 4 screws that secure the keyboard to the computer
Where used: 2 screws that secure the switch cover to the keyboard
Where used: 4 screws that secure the display assembly to the computer
132 Chapter 7 Screw listing
Where used: One screw that secures the power connector bracket to the base enclosure
Where used: One screw that secures the optical drive to the computer
Where used: 9 screws that secure the top cover to the base enclosure
Phillips PM2.5×7.0 screw 133
Where used: 2 screws that secure the display bezel to the display on computers equipped with
BrightView display assemblies
Phillips PM3.0×3.5 screw
Color
Quantity
Length
Thread
Head diameter
Silver
4
3.5 mm
3.0 mm
4.8 mm
Where used: 4 screws that secure the hard drive bracket to the hard drive
134 Chapter 7 Screw listing
8
Backup and Recovery
Recovering system information
Recovery after a system failure is as complete as your most current backup. HP recommends that you
create recovery discs immediately after software setup. As you add new software and data files, you
should continue to back up your system on a regular basis to maintain a reasonably current backup.
Tools provided by the operating system and HP Recovery Manager software are designed to help you
with the following tasks for safeguarding your information and restoring it in case of a system failure:
●
Creating a set of recovery discs (Recovery Manager software feature). Recovery discs are used
to start up (boot) your computer and restore the operating system and software programs to factory
settings in case of system failure or instability.
●
Backing up your information regularly to protect your important system files.
●
Creating system restore points (operating system feature). System restore points allow you to
reverse undesirable changes to your computer by restoring the computer to an earlier state.
●
Recovering a program or driver (Recovery Manager software feature). This feature helps you
reinstall a program or driver without performing a full system recovery.
●
Performing a full system recovery (Recovery Manager software feature). With Recovery Manager,
you can recover your full factory image if you experience system failure or instability. Recovery
Manager works from a dedicated recovery partition (select models only) on the hard drive or from
recovery discs you create.
NOTE: If your computer includes a solid-state drive (SSD), you may not have a recovery partition.
Recovery discs have been included for computers that do not have a partition. Use these discs to
recover your operating system and software. To check for the presence of a recovery partition,
select Start > Computer. If the partition is present, an HP Recovery drive is listed in the Hard Disk
Drives section of the window.
Recovering system information 135
Creating recovery discs
NOTE: HP recommends that you create recovery discs to be sure that you can restore your system
to its original factory state if you experience serious system failure or instability. Create these discs after
setting up the computer for the first time.
NOTE: Handle these discs carefully and keep them in a safe place. The software allows the creation
of only one set of recovery discs.
Note the following guidelines before creating recovery discs:
●
You will need high-quality DVD-R, double-layer DVD-R, DVD+R, double-layer DVD+R, BD-R
(writable Blu-ray), or CD-R discs. All these discs are purchased separately. DVDs and BDs have
a much higher capacity than CDs. If you use CDs, up to 20 discs may be required, whereas only
a few DVDs or BDs are required.
NOTE: Read-write discs, such as CD-RW, DVD±RW, double-layer DVD±RW, and BD-RE
(rewritable Blu-ray) discs, are not compatible with the Recovery Manager software.
●
The computer must be connected to AC power during this process.
●
Only one set of recovery discs can be created per computer.
●
Number each disc before inserting it into the computer optical drive.
●
If necessary, you can exit the program before you have finished creating the recovery discs. The
next time you open Recovery Manager, you will be prompted to continue the disc creation process.
To create a set of recovery discs:
1.
Select Start > All Programs > Recovery Manager > Recovery Manager.
Recovery Manager opens.
2.
Click Advanced Options.
NOTE: If you are operating the computer on battery power, you will be prompted to connect to
AC power before you can go to the next step.
3.
Click Recovery disc creation, and then click Next.
4.
Follow the on-screen instructions.
136 Chapter 8 Backup and Recovery
Backing up your information
When to back up
●
On a regularly scheduled basis
NOTE:
Set reminders to back up your information periodically.
●
Before the computer is repaired or restored
●
Before you add or modify hardware or software
Backup suggestions
●
Create a set of recovery discs using Recovery Manager.
●
Create system restore points using the Windows® System Restore feature, and periodically copy
them to disc.
●
Store personal files in the Documents folder and back up this folder periodically.
●
Back up templates stored in their associated programs.
●
Save customized settings in a window, toolbar, or menu bar by taking a screen shot of your settings.
The screen shot can be a time-saver if you have to reset your preferences.
To copy the screen and paste it into a word-processing document, follow these steps:
a.
Display the screen.
b.
Copy the screen:
To copy only the active window, press alt+fn+prt sc.
To copy the entire screen, press fn+prt sc.
c.
Open a word-processing document, and then select Edit > Paste.
Using system restore points
When you back up your system, you are creating a system restore point. A system restore point allows
you to save and name a snapshot of your hard drive at a specific point in time. You can then recover
back to that point if you want to reverse subsequent changes made to your system.
NOTE: Recovering to an earlier restore point does not affect data files saved or e-mails created since
the last restore point.
You also can create additional restore points to provide increased protection for your system files and
settings.
When to create restore points
●
Before you add or extensively modify software or hardware
●
Periodically, whenever the system is performing optimally
NOTE:
If you revert to a restore point and then change your mind, you can reverse the restoration.
Backing up your information 137
Create a system restore point
1.
Select Start > Control Panel > System and Maintenance > System.
2.
In the left pane, click System Protection.
3.
Click the System Protection tab.
4.
Under Automatic restore points, select the disk for which you want to create a restore point.
5.
Click Create.
The System Protection window opens.
6.
Follow the on-screen instructions.
Restore to a previous date and time
To revert to a restore point (created at a previous date and time), when the computer was functioning
optimally, follow these steps:
1.
Select Start > Control Panel > System and Maintenance > System.
2.
In the left pane, click System protection.
3.
Click the System Protection tab.
4.
Click the System Restore button, and then click Next.
The System Restore window opens.
5.
Follow the on-screen instructions.
138 Chapter 8 Backup and Recovery
Performing a recovery
NOTE: You can recover only files that you have previously backed up. HP recommends that you use
Recovery Manager to create an entire drive backup as soon as you set up your computer.
Recovery Manager software allows you to repair or restore the system if you experience system failure
or instability. Recovery Manager works from recovery discs that you create or from a dedicated recovery
partition (select models only) on the hard drive. However, if your computer includes a solid-state drive
(SSD), you may not have a recovery partition. If that is the case, recovery discs have been included
with your computer. Use these discs to recover your operating system and software.
NOTE: Windows has its own built-in repair features, such as System Restore and driver roll-back
capabilities. If you have not already tried these features, try them before using Recovery Manager.
NOTE: Recovery Manager recovers only software that was preinstalled at the factory. Software not
provided with this computer must be downloaded from the manufacturer's Web site or reinstalled from
the disc provided by the manufacturer.
Recovering from the recovery discs
To restore the system from the recovery discs:
1.
Back up all personal files.
2.
Insert the first recovery disc into the optical drive and restart the computer.
3.
Follow the on-screen instructions.
Recovering from the dedicated recovery partition (select models only)
NOTE: If your computer includes an SSD, you may not have a recovery partition. You will not be able
to recover using this procedure. Recovery discs have been included for computers that do not have a
partition. Use these discs to recover your operating system and software.
On some models, you can perform a recovery from the partition on the hard drive from either the Start
button or f11. This restores the computer to its factory condition.
To restore the system from the partition, follow these steps:
1.
Access Recovery Manager in either of the following ways:
●
Select Start > All Programs > Recovery Manager > Recovery Manager.
–or–
●
Restart the computer and press f11 while the “Press <F11> for recovery” message is displayed
on the screen. Then select Recovery Manager.
Recovery Manager opens.
2.
Click Advanced Options.
3.
Click System recovery, and then click Next.
4.
Follow the on-screen instructions.
Performing a recovery 139
9
Connector pin assignments
1394
Pin
Signal
1
Power
2
Ground
3
TPB-
4
TPB+
5
TPA-
6
TPA+
Audio-in (microphone)
Pin
Signal
1
Audio signal in
2
Audio signal in
3
Ground
140 Chapter 9 Connector pin assignments
Audio-out (headphone)
Pin
Signal
1
Audio out, left channel
2
Audio out, right channel
3
Ground
External monitor
Pin
Signal
1
Red analog
2
Green analog
3
Blue analog
4
Not connected
5
Ground
6
Ground analog
7
Ground analog
8
Ground analog
9
+5 VDC
10
Ground
11
Monitor detect
12
DDC 2B data
13
Horizontal sync
14
Vertical sync
15
DDC 2B clock
Audio-out (headphone) 141
HDMI
Pin
Signal
1
Transition minimized differential signal (TMDS) data 2+
2
TMDS data 2 shield
3
TMDS data 2–
4
TMDS data 1+
5
TMDS data 1 shield
6
TMDS data 1–
7
TMDS data 0+
8
TMDS data 0 shield
9
TMDS data 0–
10
TMDS clock+
11
TMDS clock shield
12
TMDS clock-
13
Consumer electronic control (CEC)
14
Not connected
15
DDC clock
16
DDC data
17
Ground
18
+5V power
19
Hot plug detect
142 Chapter 9 Connector pin assignments
RJ-11 (modem)
Pin
Signal
1
Unused
2
Tip
3
Ring
4
Unused
5
Unused
6
Unused
RJ-45 (network)
Pin
Signal
1
Transmit +
2
Transmit -
3
Receive +
4
Unused
5
Unused
6
Receive -
7
Unused
8
Unused
RJ-11 (modem) 143
Universal Serial Bus
Pin
Signal
1
+5 VDC
2
Data -
3
Data +
4
Ground
144 Chapter 9 Connector pin assignments
10 Power cord set requirements
The wide range input feature of the computer permits it to operate from any line voltage from 100 to 120
volts AC or from 220 to 240 volts AC.
The 3-conductor power cord set included with the computer meets the requirements for use in the
country or region where the equipment is purchased.
Power cord sets for use in other countries or regions must meet the requirements of the country or region
where the computer is used.
Requirements for all countries or regions
The requirements listed below are applicable to all countries or regions:
●
The length of the power cord set must be at least 1.5 m (5.0 ft) and no more than 2.0 m (6.5 ft).
●
All power cord sets must be approved by an acceptable accredited agency responsible for
evaluation in the country or region where the power cord set will be used.
●
The power cord sets must have a minimum current capacity of 10 amps and a nominal voltage
rating of 125 or 250 V AC, as required by each country or region.
●
The appliance coupler must meet the mechanical configuration of an EN 60 320/IEC 320 Standard
Sheet C13 connector for mating with the appliance inlet on the back of the computer.
Requirements for all countries or regions 145
Requirements for specific countries or regions
Country or region
Accredited agency
Applicable note number
Australia
EANSW
1
Austria
OVE
1
Belgium
CEBC
1
Canada
CSA
2
Denmark
DEMKO
1
Finland
FIMKO
1
France
UTE
1
Germany
VDE
1
Italy
IMQ
1
Japan
METI
3
The Netherlands
KEMA
1
Norway
NEMKO
1
The People's Republic of China
CCC
5
South Korea
EK
4
Sweden
SEMKO
1
Switzerland
SEV
1
Taiwan
BSMI
4
The United Kingdom
BSI
1
The United States
UL
2
1.
The flexible cord must be Type HO5VV-F, 3-conductor, 1.0-mm² conductor size. Power cord set fittings (appliance coupler
and wall plug) must bear the certification mark of the agency responsible for evaluation in the country or region where it
will be used.
2.
The flexible cord must be Type SPT-3 or equivalent, No. 18 AWG, 3-conductor. The wall plug must be a two-pole grounding
type with a NEMA 5-15P (15 A, 125 V) or NEMA 6-15P (15 A, 250 V) configuration.
3.
The appliance coupler, flexible cord, and wall plug must bear a “T” mark and registration number in accordance with the
Japanese Dentori Law. The flexible cord must be Type VCT or VCTF, 3-conductor, 1.00-mm² conductor size. The wall
plug must be a two-pole grounding type with a Japanese Industrial Standard C8303 (7 A, 125 V) configuration.
4.
The flexible cord must be Type RVV, 3-conductor, 0.75-mm² conductor size. Power cord set fittings (appliance coupler
and wall plug) must bear the certification mark of the agency responsible for evaluation in the country or region where it
will be used.
5.
The flexible cord must be Type VCTF, 3-conductor, 0.75-mm² conductor size. Power cord set fittings (appliance coupler
and wall plug) must bear the certification mark of the agency responsible for evaluation in the country or region where it
will be used.
146 Chapter 10 Power cord set requirements
11 Recycling
Battery
When a battery has reached the end of its useful life, do not dispose of the battery in general household
waste. Follow the local laws and regulations in your area for computer battery disposal.
Display
WARNING! The backlight contains mercury. Caution must be exercised when removing and handling
the backlight to avoid damaging this component and causing exposure to the mercury.
CAUTION: The procedures in this chapter can result in damage to display components. The only
components intended for recycling purposes are the liquid crystal display (LCD) panel and the backlight.
Careful handling must be exercised when removing these components.
NOTE: Materials Disposal. This HP product contains mercury in the backlight in the display assembly
that might require special handling at end-of-life. Disposal of mercury may be regulated because of
environmental considerations. For disposal or recycling information, contact your local authorities, or
see the Electronic Industries Alliance (EIA) Web site at http://www.eiae.org.
This section provides disassembly instructions for the display assembly. The display assembly must be
disassembled to gain access to the backlight (1) and the liquid crystal display (LCD) panel (2).
NOTE: The procedures provided in this chapter are general disassembly instructions. Specific details,
such as screw sizes, quantities, and locations, and component shapes and sizes, can vary from one
computer model to another.
Battery 147
Perform the following steps to disassemble the display assembly:
1.
Remove all screw covers (1) and screws (2) that secure the display bezel to the display assembly.
2.
Lift up and out on the left and right inside edges (1) and the top and bottom inside edges (2) of the
display bezel until the bezel disengages from the display assembly.
3.
Remove the display bezel (3).
148 Chapter 11 Recycling
4.
Disconnect all display panel cables (1) from the display inverter and remove the inverter (2).
5.
Remove all screws (1) that secure the display panel assembly to the display enclosure.
6.
Remove the display panel assembly (2) from the display enclosure.
7.
Turn the display panel assembly upside down.
8.
Remove all screws that secure the display panel frame to the display panel.
9.
Use a sharp-edged tool to cut the tape (1) that secures the sides of the display panel to the display
panel frame.
Display 149
10. Remove the display panel frame (2) from the display panel.
11. Remove the screws (1) that secure the backlight cover to the display panel.
12. Lift the top edge of the backlight cover (2) and swing it outward.
13. Remove the backlight cover.
14. Turn the display panel right-side up.
150 Chapter 11 Recycling
15. Remove the backlight cables (1) from the clip (2) in the display panel.
16. Turn the display panel upside down.
17. Remove the backlight frame from the display panel.
WARNING! The backlight contains mercury. Exercise caution when removing and handling the
backlight to avoid damaging this component and causing exposure to the mercury.
Display 151
18. Remove the backlight from the backlight frame.
19. Disconnect the display cable (1) from the LCD panel.
20. Remove the screws (2) that secure the LCD panel to the display rear panel.
21. Release the LCD panel (3) from the display rear panel.
22. Release the tape (4) that secures the LCD panel to the display rear panel.
23. Remove the LCD panel.
24. Recycle the LCD panel and backlight.
152 Chapter 11 Recycling
Index
Symbols/Numerics
1394 port
identifying 14
pin assignments 140
1394 Power Saving 101
A
AC adapter, spare part
numbers 30, 31
administrator password 101
antennas 17
applications key, Windows 11
audio cable
illustrated 29
audio, product description 3
audio-in (microphone) jack,
identifying 12
audio-in jack
pin assignments 140
audio-out (headphone) jack
identifying 12
pin assignments 141
audio/infrared board
removal 84
spare part number 24, 34,
84
B
backup
customized window, toolbar,
and menu bar settings 137
personal files 137
templates 137
backup and recovery 135
backup suggestions 137
base enclosure, spare part
numbers 24, 38
battery
removal 48
spare part numbers 25, 34,
48
battery bay, identifying 15
battery light, identifying 7, 12
battery release latch,
identifying 15
bays
battery 15
hard drive 15
Blu-ray ROM DVD±R/RW
SuperMulti DL Drive
removal 51
spare part numbers 25, 33,
51
specifications 108
Blu-ray ROM with LightScribe DVD
±R/RW SuperMulti Double-Layer
Drive
precautions 25, 51
spare part number 25, 51
Bluetooth cable, spare part
number 31
Bluetooth module
removal 79
spare part numbers 31, 79
boot options 102
boot order 102
button sound 101
buttons
next/fast forward 10
play/pause 9
power 9
previous/rewind 9
stop 10
TouchPad 6
TouchPad on/off 6
volume mute 9
C
Cable Kit
contents 29
spare part number 29, 38
cables, service considerations 42
caps lock, lights 7
Card Reader Power Saving 101
changing the Setup Utility
language 99
chipset, product description 1
cleaning the display 16
compartments
memory module 15
WLAN module 15
components
bottom 15
display 16
front 12
left-side 14
rear 13
right-side 13
top 6
computer feet
locations 47
spare part number 47
computer specifications 103
connectors, power 13
connectors, service
considerations 42
D
Diagnostics menu 102
Digital Media Slot, identifying 14
diskette drive, precautions 42
display
cleaning 16
display assembly
removal 49
spare part numbers 19, 37,
39, 49
Index 153
display bezel
illustrated 27
release 49
spare part number 27, 34,
75
display cable, spare part
numbers 27, 34
display components
illustrated 20, 27
recycling 147
display enclosure
illustrated 26, 28
removal 70
spare part numbers 26, 28,
34, 35, 40, 71
display hinge
illustrated 26, 27
removal 73, 76
spare part numbers 26, 27,
73, 77
Display Hinge Kit, spare part
numbers 26, 27, 34, 73, 77
display inverter
illustrated 26, 27
removal 71, 75
spare part number 26, 27,
31, 72, 75
display inverter cover
removal 71
spare part number 71
display panel
illustrated 27
product description 2
removal 76
spare part numbers 27, 34,
39, 76
Display Rubber Kit, spare part
number 26, 28, 34
Display Screw Kit, spare part
number 26, 28, 34
display specifications 104, 105,
106
display switch, identifying 16
displaying system
information 100
docking support, product
description 4
drive light, identifying 7, 12
154 Index
drives
boot order 102
preventing damage 42
drives, hard 15
DVD±RW and CD-RW SuperMulti
Double-Layer Combo Drive
precautions 42
removal 51
spare part numbers 33, 51
specifications 109
E
electrostatic discharge 43
eSATA/USB port, identifying 14
esc key, identifying 11
Ethernet, product description 3
exiting the Setup Utility 100
expansion port, identifying 14
ExpressCard slot bezel,
illustrated 28
ExpressCard slot, identifying 14
external media cards, product
description 4
external monitor port
identifying 14
pin assignments 141
F
f11 recovery 139
fan always on 102
fan/heat sink assembly
removal 92
spare part numbers 24, 38,
92
feet
locations 47
spare part number 47
fingerprint reader cable
illustrated 29
fingerprint reader, identifying 10
fn key, identifying 11
full system recovery 135
function keys, identifying 11
G
graphics, product description
grounding equipment and
methods 45
1
H
hard drive
precautions 42
product description 2
removal 57
spare part numbers 24, 33,
38, 57
specifications 107
hard drive bay, identifying 15
hard drive cover
illustrated 28
removal 58
Hard Drive Hardware Kit, spare part
number 24, 31, 57
hard drive self test 102
HDMI port
identifying 14
pin assignments 142
headphone (audio-out) jack
identifying 12
pin assignments 141
hinge
illustrated 26, 27
removal 73, 76
spare part numbers 26, 27,
73, 77
I
I/O address specifications 112
IEEE 1394 port, identifying 14
infrared lens, identifying 12
internal display switch,
identifying 16
internal microphone,
identifying 16
interrupt specifications 111
J
jacks
audio-in (microphone) 12
audio-out (headphone) 12
RJ-11 (modem) 13
RJ-45 (network) 14
TV antenna/cable 13
K
keyboard
product description 4
removal 63
spare part numbers 20, 35,
36, 39, 63
keypad keys, identifying 11
keys
esc 11
fn 11
function 11
keypad 11
Windows applications 11
Windows logo 11
L
LAN Power Saving 101
language support 101
latch, battery release 15
lights
battery 7, 12
caps lock 7
drive 7, 12
num lock 8
power 7, 12
TouchPad 6
volume down 7
volume mute 7
volume up 7
wireless 8
M
Main menu 101
media activity buttons,
identifying 9
memory map specifications 114
memory module
identifying 15
product description 2
removal 53
spare part numbers 25, 33,
53
memory module compartment
cover
illustrated 28
removal 53
memory test 102
microphone (audio-in) jack 12
microphone jack
pin assignments 140
microphone, internal 16
microphone, product
description 3
model name 1
modem jack
pin assignments 143
modem module
removal 83
spare part numbers 24, 34,
83
modem module cable
illustrated 29
removal 91
modem, product description 3
monitor port
external 14
pin assignments 141
mute button, identifying 9
N
navigating in the Setup Utility 99
network jack
pin assignments 143
next/fast forward button,
identifying 10
notebook sleeve, spare part
number 38
num lock light, identifying 8
O
operating system, product
description 5
optical drive
identifying 13
precautions 42
product description 3
removal 51
spare part numbers 25, 51
specifications 108, 109
P
packing guidelines 44
passwords 101
pin assignments
1394 140
audio-in 140
audio-out 141
external monitor 141
HDMI 142
headphone 141
microphone 140
modem 143
monitor 141
network 143
RJ-11 143
RJ-45 143
Universal Serial Bus
(USB) 144
plastic parts 41
Plastics Kit
contents 28
spare part number 21, 28,
34
play/pause button, identifying 9
pointing device
product description 4
ports
1394 14
eSATA/USB 14
expansion 14
external monitor 14
HDMI 14
product description 4
USB 13, 14
power button board
removal 67
spare part number 20, 34,
67
power button, identifying 9
power connector cable
removal 86
spare part number 21
power connector, identifying 13
power cord
set requirements 145
spare part numbers 30, 31,
32
power light, identifying 7, 12
power requirements, product
description 4
power-on password 101
previous/rewind button,
identifying 9
procedure 139
processor
product description 1
removal 88
spare part numbers 21, 40,
88
Processor C6 State 101
product description
audio 3
chipset 1
display panel 2
docking support 4
Index 155
Ethernet 3
external media cards 4
graphics 1
hard drives 2
keyboard 4
memory module 2
microphone 3
modem 3
operating system 5
optical drives 3
pointing device 4
ports 4
power requirements 4
processors 1
product name 1
security 5
serviceability 5
TV tuner 3
webcam 3
wireless 3
product name 1
R
recovery
from the dedicated recovery
partition 139
from the recovery discs 139
program or driver 135
system 135
recovery discs 135
Recovery Manager 135
recovery partition 135
remote control, spare part
numbers 30, 31
removal/replacement
preliminaries 41
procedures 46
restore points 137
restoring default settings 100
RJ-11 (modem) jack
identifying 13
pin assignments 143
RJ-45 (network) jack
identifying 14
pin assignments 143
RTC battery
removal 56
spare part number 25, 31,
56
156 Index
Rubber Feet Kit, spare part
number 25, 34, 47
S
Screw Kit
contents 115
spare part numbers 31, 34
screw listing 115
scrolling zones, TouchPad 6
secondary hard drive self
test 102
security cable slot, identifying 13
Security menu 101
security, product description 5
selecting in the Setup Utility 99
service considerations 41
service tag 18, 46
serviceability, product
description 5
Setup Utility
menus 101
starting 98
using 99
slots
Digital Media 14
ExpressCard 14
memory module 15
security cable 13
solid-state drive (SSD) 135, 139
speaker
identifying 9
removal 78
spare part numbers 38, 78
specifications
Blu-ray ROM DVD±R/RW
SuperMulti DL Drive 108
computer 103
display 104, 105, 106
DVD±RW and CD-RW
SuperMulti Double-Layer
Combo Drive 109
hard drive 107
I/O addresses 112
interrupts 111
memory map 114
optical drive 108, 109
system DMA 110
static-shielding materials 45
stop button, identifying 10
supported discs 136
switch cover
removal 63
spare part number 20, 36,
39, 63
system board
removal 87
spare part numbers 21, 33,
34, 40, 87
System Configuration menu 101
system DMA 110
system failure or instability 135
system information 101
system memory map 114
system recovery 135
system restore points 135, 137
T
thermal material,
replacement 93, 95
tools required 41
top cover
removal 80
spare part numbers 21, 36,
37, 39, 80
TouchPad buttons, identifying 6
TouchPad light, identifying 6
TouchPad on/off button 6
TouchPad scrolling zones,
identifying 6
TouchPad, identifying 6
transporting guidelines 44
TV antenna/cable jack,
identifying 13
TV tuner external antenna cable,
spare part numbers 25, 31, 55
TV tuner module
product description 3
removal 55
spare part numbers 25, 31,
55
TV tuner module cable
illustrated 29
removal 90
U
Universal Serial Bus (USB) port
pin assignments 144
USB board
removal 85
spare part number 21, 34,
85
USB cable
illustrated 29
USB ports, identifying 13, 14
using system restore 137
V
vents, identifying 13, 15
Virtualization Technology 101
volume down light, identifying 7
volume mute button, identifying 9
volume mute light, identifying 7
volume scroll zone, identifying 9
volume up light, identifying 7
W
webcam
identifying 16
product description 3
webcam/microphone cable, spare
part numbers 27
webcam/microphone module
illustrated 26, 27
removal 49, 50, 71
spare part numbers 26, 27,
34, 49, 72
Windows applications key,
identifying 11
Windows logo key, identifying 11
wireless antenna cable, spare part
numbers 27
wireless antennas 17
wireless light, identifying 8
wireless, product description 3
WLAN module
removal 60
spare part numbers 22, 32,
33, 60
WLAN module compartment,
identifying 15
workstation guidelines 44
Index 157