Baumatic B70.1BL User manual

B70.1BL 60 cm 4 Burner glass gas hob
with thermocouples
B77TCBL 70 cm 5 Burner gas glass hob
with thermocouples.
B72BL 60 cm 4 Burner glass gas hob
B77BL 70 cm 5 Burner glass gas hob
1
User Manual for your Baumatic
B70.1BL 60 cm 4 Burner gas glass hob
with thermocouples
B77TCBL 5 burner gas glass hob with
thermocouples
B72BL 60 cm 4 burner gas glass hob
B77BL 5 burner gas glass hob
NOTE: This User Instruction Manual contains important
information, including safety & installation points, which will
enable you to get the most out of your appliance. Please keep it
in a safe place so that it is easily available for future reference; for
you or any person not familiar with the operation of the appliance.
DD 23/02/09
2
Contents
Environmental note
4
Important safety information
5–7
Specifications
B70.1BL
B77TCBL
B72BL
B77TCBL
Electrical details
Gas details
Gas hob surface layout
8 – 13
8
9
10
11
12
12
12 - 13
Using the gas hob
Before first use
Switching the hob on
Automatic ignition
(B72BL/B77BL)
Automatic ignition with flame failure safety device
(B70.1BL/B77TCBL)
Energy saving tips
14 - 16
14
14
14 - 15
14 - 15
15 - 16
Cleaning
Cleaning the hob top
After each use
Cleaning the hob burners
Maintaining the cast iron pan stands
16 - 17
16
17
17
17
Installation
Positioning
Unpacking the appliance
Installing the appliance
Gas connection
Ventilation requirements
Gas Safety (Installation and Use) Regulations
Gas Adjustment (Conversion to LPG)
Minimum flow adjustment for hob gas taps
Gas tap maintenance
Electrical connection
Replacing the mains supply cable
18 - 28
19
20
20 - 22
22
23
24
25 - 26
26
27
28
28
My appliance isn’t working correctly
29
Contact details
30
3
Environmental note
o The packaging materials that Baumatic uses are environmentally
friendly and can be recycled.
o Please discard all packaging material with due regard for the
environment.
4
Important safety information
Your safety is of the utmost importance to Baumatic.
Please make sure that you read this instruction booklet
before attempting to install or use the appliance. If you
are unsure of any of the information contained in this
booklet, please contact the Baumatic Advice Line.
General Information
o This appliance is designed for domestic household use and for
the cooking and frying of domestic foodstuffs.
o IMPORTANT: The adjacent furniture and all materials used in
the installation must be able to withstand a minimum
temperature of 85°C above the ambient temperature of the
room it is located in, whilst in use.
o Certain types of vinyl or laminate kitchen furniture are
particularly prone to heat damage or discolouration at
temperatures below the guidelines given above.
o Any damage caused by the appliance being installed in
contravention of this temperature limit, will be the liability of
the owner.
o Your new appliance is guaranteed against electrical or
mechanical defects, subject to certain exclusions that are noted
in Baumatic’s Conditions Of Guarantee. The foregoing does not
affect your statutory rights.
o The use of this appliance for any other purpose or in any other
environment without the express agreement of Baumatic Ltd.
will invalidate any warranty or liability claim.
o You should not use this appliance to store items on or as a work
surface.
o No modifications to the appliance are permitted by Baumatic Ltd.
o You should not store or place flammable or highly flammable
liquids/materials on top of or near the appliance. Items made
from aluminium, plastic or plastic film should also be kept away
from the appliance, as they may fuse to the surface.
o Repairs may only be carried out by Baumatic service
engineers or their authorised service agent.
5
Child Safety
o Baumatic strongly recommend that babies and young children
are prevented from being near to the appliance and not allowed
to touch the appliance at any time. During and after use, all
surfaces will be hot.
o If it is necessary for younger family members to be in the
kitchen, please ensure that they are kept under close supervision
at all times.
o Older children should only be allowed to utilise the appliance
when supervised.
General Safety
o The appliance should only be installed and connected by a
CORGI registered installer.
o Care should be taken to ensure that the units and work surfaces
that you build the appliance into, meet with the relevant
standards.
During use
o Any film or stickers that are present on the hob surface when it
is delivered should be removed before use.
o Care should be used when utilising the appliance, otherwise
there is a risk of burns being caused.
o You should not allow the electrical connection cables to come
into contact with the hob surface when it is hot or any hot
cookware.
o If fat and oil overheats, then it can ignite extremely quickly. For
this reason, when cooking with fat and oil the appliance should
not be left unattended.
o Make sure that all of the cooking zones are switched off after
use.
Cleaning
o Cleaning of the hob should be carried out on a regular basis.
o IMPORTANT: Before attempting to clean the appliance, it
should be disconnected from the mains and cool.
6
o Great care should be taken whilst using this appliance and when
following the cleaning procedure.
o You should not use a steam jet or any other high pressure
cleaning equipment to clean the appliance.
Installation
This appliance must be correctly installed by a
CORGI registered installer, strictly in accordance
with the manufacturer’s instructions and the
relevant British Standards. Please see the specific
section of this booklet that refers to installation.
o Baumatic Ltd. declines any responsibility for injury or
damage, to person or property, as a result of improper
use or installation of this appliance.
o If the appliance is being used in a Leisure Accommodation
Vehicle, the requirements of N 721 MUST be followed.
o Baumatic Ltd. DO NOT recommend that this appliance is
installed on any type of marine vessel.
Declaration of conformity
This appliance complies with the following European Directives:
-73/23/EEC dated 19/02/1973 Low Voltage Directive.
-89/336/EEC dated 03/05/1989 EMC Directive inclusive of
Amending Directive 92/31/EEC.
-93/68/EEC dated 22/07/1993 CE Marking Directive.
-89/109/EEC dated 25/01/1992 Materials that can touch food.
-90/396/EEC Gas Products.
-EN60335-1, EN60335-2, EN301-1 Safety Standards.
The manufacturer declares that the hob is built using certified
materials and requires the appliance to be installed in accordance with
the standards currently in force. This appliance must be used by a
trained person for domestic purposes only.
7
Specifications
B70.1BL
Product dimensions:
Aperture dimensions:
Height:
Width:
Depth:
Height:
Width:
510 mm
580 mm
50 mm
490 mm
560 mm
Product specifications:
o 1 x 3.00 kW rapid burner
o 2 x 1.75 kW semi-rapid burners
o 1 x 1.00 kW auxiliary burner
o
o
o
o
Side control operation
Automatic ignition
Flame failure safety device on each burner
RANA cast iron pan stands
Standard accessories:
o LPG conversion jets
8
B77TCBL
Product dimensions:
Aperture dimensions:
Height:
Width:
Depth:
Height:
Width:
510 mm
680 mm
50 mm
490 mm
562 mm
Product specifications:
o
o
o
o
1
1
2
1
x
x
x
x
3.50
3.00
1.75
1.00
kW
kW
kW
kW
wok burner
rapid burner
semi-rapid burners
auxiliary burner
o
o
o
o
Front control operation
Automatic ignition
Flame failure safety device on each burner
RANA cast iron pan stands
Standard accessories:
o LPG conversion jets
9
B72BL
Product dimensions:
Aperture dimensions:
Height:
Width:
Depth:
Height:
Width:
510 mm
580 mm
50 mm
490 mm
560 mm
Product specifications:
o 1 x 3.00 kW rapid burner
o 2 x 1.75 kW semi-rapid burners
o 1 x 1.00 kW auxiliary burner
o Front control operation
o Automatic ignition
o RANA cast iron pan stands
Standard accessories:
o LPG conversion jets
10
B77BL
Product dimensions:
Aperture dimensions:
Height:
Width:
Depth:
Height:
Width:
510 mm
680 mm
50 mm
490 mm
562 mm
Product specifications:
o
o
o
o
1
1
2
1
x
x
x
x
3.50
3.00
1.75
1.00
kW
kW
kW
kW
wok burner
rapid burner
semi-rapid burners
auxiliary burner
o Front control operation
o Automatic ignition
o RANA cast iron pan stands
Standard accessories:
o LPG conversion jets
11
Electrical details
Rated Voltage:
Supply Connection:
Max Rated Inputs:
Mains Supply Lead:
230 Vac 50 Hz
3 A (double pole switched fused outlet with
3mm contact gap)
0.008 to 0.02 kW (depending on model)
3 core x 0.75mm² (Type RR-F <HAR> marked)
Gas details
Connection:
Type:
Rp ½ (ISO R7)
Natural Gas (20.9 mbar),
Alternative LPG G30 (28-30 mbar),
Town gas G110 – 120 (8 mbar) to order.
For future reference please record the following information which can
be found on the rating plate and the date of purchase which can be
found on your sales invoice. The rating plate of your hob is located on
the underneath of the appliance. Therefore it is a good idea to record
this information before you install your appliance.
Model Number
……………………………….
Serial Number
……………………………….
Date of Purchase
……………………………….
Gas hob surface layout
B70.1BL
12
B72BL
B77BL/B77TCBL
13
Using the gas hob
Before first use
IMPORTANT: You should clean the hob surface (see
“Cleaning and maintenance” section).
Switching the hob on
The following symbols will appear on the control panel, next to each
control knob:
0 = gas off
Large flame: maximum setting
Small flame: minimum setting
o The minimum setting is at the end of the anti-clockwise rotation
of the control knob.
o All operation positions must be selected between the maximum
and minimum position.
o Never select a knob position between the maximum and off
position.
o The symbol on the control panel, next to the control knob will
indicate which gas burner it operates.
Automatic ignition (B72BL/B77BL)
To ignite a burner:
o Press in the control knob of the burner that you wish to light and
turn it anti-clockwise to the maximum position.
o If you keep the control knob depressed, the automatic ignition
for the burner will operate.
o Once the burner is lit, turn the control knob to your required
setting between the maximum and minimum setting symbols.
o To turn the burner off, turn the control knob fully clockwise to
the gas off position.
14
o In case of power failure, the burners can be lit by carefully using
a match.
Automatic ignition with flame failure safety device
(B70.1BL/B77TCBL)
The appliance is fitted with a flame failure safety device on each
burner, which is designed to stop the flow of gas to the burner head in
the event of the flame going out.
To ignite a burner:
o Press in the control knob of the burner that you wish to light and
turn it anti-clockwise to the maximum position.
o If you keep the control knob depressed, the automatic ignition
for the burner will operate.
o You should hold down the control knob for 20 seconds after the
flame on the burner has lit.
o After this 20 second interval, turn the control knob to your
required setting between the maximum and minimum setting
symbols.
o In case of power failure, the burners can be lit by carefully using
a match.
o To turn the burner off, turn the control knob fully clockwise to
the gas off position.
o In case of power failure, the burners can be lit by carefully using
a match.
Energy saving tips
BURNERS
PANS
Minimum Maximum
diametre diametre
Wok
220 mm
260 mm
Rapid
180 mm
220 mm
Semi-rapid 120 mm
200 mm
Auxiliary
80 mm
160 mm
o The diametre of the bottom of the pan should correspond to that
of the burner.
15
o The burner flame must never extend beyond the diametre of the
pan.
o Use flat bottomed pans only
o When possible, keep a lid on the pan whilst cooking.
o Cook vegetables with as little water as possible, to reduce
cooking times.
IMPORTANT: Always place pans centrally over the hob burners and
position them so that the handles cannot get accidentally caught or
knocked off. You should also make sure that the handle is not over one
of the other hob burner flames.
Cleaning
Cleaning operations must only be carried out when
the hob is cool.
The appliance should be disconnected from your
mains supply before commencing any cleaning
process.
Cleaning the hob top
Any residues that are left on the hob top surface from cleaning
agents will damage it. You should remove any residues with
warm soapy water.
Abrasive cleaners or sharp objects will damage the hob surface;
you should clean it using warm soapy water.
Although it is easier to clean some deposits whilst the
hob surface is still warm. Make sure that the hob surface,
pan supports and hob burners have all cooled sufficiently
before you attempt to touch them.
16
After each use
o Remove the pan stands and wipe the appliance over with a soft,
damp cloth that has been put into warm soapy water. The cloth
should be wrung out after being taken out of the soapy water.
o Dry the appliance by rubbing the surface with a soft, clean cloth.
Cleaning the hob burners
The hob burners should be cleaned once a week or more frequently if
they get soiled.
o IMPORTANT: Make sure that the hob surface, pan stands and
hob burners have cooled before you attempt to touch them.
o Remove the hob burners by pulling them upwards and away
from the hob top.
o Soak them for about ten minutes in hot water and a little
detergent.
o After cleaning and washing them, wipe and dry them carefully.
o Before placing the burners back on the hob top, make sure that
the gas jet is not blocked.
o IMPORTANT: Make sure that you reassemble the burners in the
original way.
Maintaining the cast iron pan stands
o IMPORTANT: Make sure that the hob surface and pan stands
have cooled before you attempt to touch them.
o Wipe the pan stands over with a soft, damp cloth that has been
put into warm soapy water. The cloth should be wrung out after
being taken out of the soapy water.
o Using a paper towel, thoroughly dry the pan stands.
o To maintain the appearance of the cast iron pan stands, we
would recommend that you rub a small amount of olive oil into
the pan stands. After you have finished cleaning them.
17
Installation
The installation must be carried out by a CORGI
registered installer, in accordance with the current
version of the following.
o Gas Safety Regulations (Installation & Use)
o Building Regulations (issued by the Department of Environment)
o Building Standards (Issued by the Scottish Development
Department)
o IEE Wiring Regulations
o Electricity at Work Regulations BS 6172
o Installation of Domestic Gas Cooking Appliances (if necessary,
BS 5482 Installation of Domestic LPG Appliances)
o BS 5440 Installation of Flues and Ventilation for Gas Appliances
o Baumatic Ltd Installation Instructions
18
Positioning
The adjacent furniture must be able to withstand a
minimum temperature rise of 85°C above the ambient
temperature of the room it is located in, during
periods of use.
o This appliance can be located in a kitchen, a kitchen diner or a
bed sitting room. IMPORTANT: The appliance must not be
installed in a bathroom or shower room.
This appliance is classified as Class 3 and therefore is to be built into a
kitchen unit (depending on size) or 600mm worktop, providing the
following minimum distances are allowed:
o The edges of the hob must be a minimum distance of 55 mm
from a side or rear wall.
o 700 mm between the highest point of the hob surface (including
the burners) and the underside of any horizontal surface directly
above it.
o 400 mm between the hob surface, providing that the underside
of the horizontal surface is in line with the outer edge of the hob.
If the underside of the horizontal surface is lower than 400 mm,
then it must be at least 50 mm away from the outer edges of
the hob.
o 50 mm clearance around the appliance and between the hob
surface and any combustible materials.
19
Unpacking the appliance
When unpacking the appliance please check that the following items
are contained within the packaging:
1 x Baumatic hob
4 x Pan stands (B70.1BL/B72BL)
5 x Pan stands (B77BL/B77TCBL)
1 x Installation and instruction manual
1 x Baumatic guarantee card
4 x Fixing screws
4 x Clamps
1 x Sealing strip
1 x LPG conversion kit
1 x Self-adhesive label for amending the Gas Category on the
appliance’s rating plate (required if the LPG conversion kit is used).
Installing the appliance
B70.1BL/B72BL
B77BL/B77TCBL
20
o Cut a hole in the worktop that corresponds with the drawings
shown on page 20.
o IMPORTANT: You must have a gap of at least 25 mm between
the underneath of the appliance and any surface that is below it.
o Carefully turn the hob upside down and place it on a cushioned
mat.
o Apply the sealing strip (A) provided around the edge of the
appliance.
o The protective covering must be removed from both sides.
o Do not leave a gap in the sealing agent or overlap the thickness.
o IMPORTANT: Do not use a silicon sealant to seal the appliance
against the aperture. This will make it difficult to remove the hob
from the aperture in future, particularly if it needs to be
serviced.
(A)
(B)
(C)
Sealing strip
Clamp
Screw
21
o Place the clamp (B) over the holes that match the size of the
screws. There are one set of screw holes in each corner of the
hob. Slightly tighten a screw (C) through the clamp (B) so that
the clamp is attached to the hob, but so that you can still adjust
the position of it.
o Carefully turn the hob back over and then gently lower it into the
aperture hole that you have cut out.
o On the underneath of the hob, adjust the clamps into a position
that is suitable for your worktop. Then fully tighten the screws
(C) to secure the hob into position.
Gas connection
This appliance must be installed by a competent
person in accordance with the current versions of
the following UK (United Kingdom) or ROI (Republic
of Ireland) Regulations and Safety Standards or
their European Norm Replacements.
Important information
o This cooker is supplied to run on natural gas only and cannot
be used on any other type of gas without modification.
o Conversion for use on LPG and other gases must only be
undertaken by a qualified person. For information on the use of
other gases, please contact the Baumatic Advice Line.
o The cooker must be installed by a qualified person, in
accordance with the current edition of the Gas Safety
(Installation and Use) (Amendment) Regulations and the
relevant building/I.E.E. Regulations.
o Failure to install the appliance correctly could invalidate
Baumatic’s guarantee and lead to prosecution under the
regulations quoted above.
o In the UK, CORGI registered installers are authorised to
undertake the installation and service work, in compliance with
the above regulations.
22
Ventilation requirements
o The room containing the hob should have an air supply in
accordance with the current edition of BS 5440: Part 2:
o The room must have opening windows or equivalent; some
rooms may also require a permanent vent.
o If the room has a volume between 5 and 10m³, it will require an
air vent of 50cm² (effective area). Unless it has a door which
opens directly to the outside.
o If the room has a volume of less than 5m³, it will require an air
vent of 100cm² (effective area).
o If it is installed in a room with a volume that exceeds 11m³, then
no air vent is required.
o If there are any other fuel burning appliances in the same room
the current edition of BS 5440: Part 2: should be consulted to
determine air vent requirements.
o Ensure that the room containing the hob is well ventilated, keep
natural ventilation holes or install a mechanical ventilation device
(mechanical cooker hood).
o Prolonged intensive use of the appliance may call for additional
ventilation, either by the opening of a window, or by increasing
the level of the mechanical ventilation device (where present).
o This hob is not fitted with a device for discharging the products
of combustion. Ensure that the ventilation rules and regulations
are followed.
o The walls behind and near the hob should be resistant to heat,
steam and condensation.
o Remember that the quantity of air necessary for combustion
must never be less than 2m³/h for each kW of power (see total
power in kW on the appliance rating plate).
23
Gas Safety (Installation and Use) Regulations
IMPORTANT: The appliance MUST be connected to the gas
supply by use of a ½ BSP Elbow, seal, copper pipe and an
isolation tap fitted in an easily accessible position.
o It is the law that all gas appliances are installed by competent
persons in accordance with the current edition of the Gas Safety
Installation and Use Regulations.
o It is in your interest and that of safety to ensure compliance with
the law.
o In the UK, CORGI registered installers work to safe standards of
practice. The cooker must also be installed in accordance with
the current edition of BS 6172. Failure to install the hob correctly
could invalidate the warranty, liability claims and lead to
prosecution.
o Put the gas seal into the elbow.
o Fully tighten the elbow and seal onto the gas rail.
o The elbow MUST be pointing in a downwards direction.
o Gas pressure may be checked on a semi-rapid hob burner.
Remove the appropriate injector and attach a test nipple. Light
the other burners and observe that the gas pressure complies
with the gas standards in force.
o IMPORTANT: On completion carry out a gas soundness
test.
24
Gas adjustment (Conversion to LPG)
All work must be carried out by a CORGI registered
engineer.
IMPORTANT: Always isolate the hob from the electricity supply
before changing the injectors and/or adjusting the minimum
flow of the burners.
o Remove the pan-stands, burners and
flame spreaders (A).
o Unscrew the injector (B) and replace it
with the stipulated injector for the new gas
supply (see table below).
GENERAL INJECTORS TABLE
Kind of gas
Nozzle
Burners Power (in watts)
mm/100
Max.
Min.
Natural
135
Wok
3500
1700
115
Rapid
3000
700
1750
400
97
Semi-rapid
72
Auxiliary
1000
350
L.P.G.
95
Wok
3500
1700
Butane
85
Rapid
3000
700
Propane
65
Semi-rapid
1750
400
50
Auxiliary
1000
350
o Reassemble all the burners carefully; in particular you should
make sure that the flame spreader is correctly placed on the
burner.
25
o IMPORTANT: The minimum flow adjustment process must
be completed before the appliance is next used.
Minimum flow adjustment for hob gas taps.
All work must be carried out by a CORGI registered
engineer.
IMPORTANT: Always isolate the hob from the electricity supply
before changing the injectors and/or adjusting the minimum
flow of the burners.
o Switch the burner
on and set the
knob at the
minimum
position.
o Remove the knob
from the tap and
place a small
bladed
screwdriver in the
centre of the tap
shaft.
o Unscrew the adjusting screw, in order to increase the gas flow
or tighten the adjusting screw to decrease the gas flow.
o The correct adjustment is obtained when the flame has a
length of about 3 – 4 mm.
o For butane/propane gas, the adjusting screw must be tightly
screwed in.
o Refit the control knob.
o Make sure that the flame does not go out by quickly turning
from maximum flow to minimum flow. If it does then remove
the control knob and make further adjustments to the gas
flow, testing it again once the adjustment has been made.
o Repeat this process for each one of the gas taps.
26
Gas tap maintenance
These maintenance operations MUST ONLY be carried
out by a CORGI registered engineer.
IMPORTANT: Before carrying out any maintenance operations,
disconnect the appliance from the gas and electricity supplies.
If a gas tap becomes stiff to operate, then you should proceed as
follows:
o Remove the control knobs, pan supports, burners, hob fixing
screws and clamps.
o Remove the hob from the worktop and remove any underside
protective covers.
o Disconnect the fixings holding the tap to the fascia panel and
separate the assembly. Then clean the cone and seating, with
a cloth dampened with solvent.
o Lightly smear the cone with high temperature grease,
reassemble into position and rotate a few times.
o Remove the cone again and remove any excess grease,
making sure that the gas ducts are not obstructed with
grease.
o Carefully reassemble the components and perform a gas
soundness test.
If it becomes necessary to replace a gas tap, then you should proceed
as follows:
o Remove the control knobs, pan supports, burners, hob fixing
screws and clamps.
o Remove the hob from the worktop and remove any underside
protective covers.
o Disconnect the fixings holding the tap to the fascia panel and
separate the assembly.
o Disconnect the gas pipe from the gas tap, then disassemble
them from the gas rail by removing the fixing screws.
o When fitting a new tap, ensure that a new gasket is used.
o Reconnect the gas tap, perform a gas soundness test and
then reassemble the hob.
27
Electrical connection
This appliance must be installed by a qualified
person in accordance with the latest edition of the
I.E.E. Regulations and in compliance with Baumatic’s
instructions.
Before connecting the appliance, make sure that the supply voltage
marked on the rating plate corresponds with your mains supply
voltage.
o Cable type: H05 RRF 3 core x 0.75 mm³ (Type RR-F <HAR>
marked).
o The mains supply cable is supplied with this product.
Replacing the mains supply cable
If the mains supply cable is damaged, then it must be replaced by an
appropriate replacement which can be obtained from the Baumatic
Spares Department.
The mains supply cable should be replaced in accordance with the
following instructions:
o Switch the appliance off at the control switch.
o Open the box of the supply board.
o Unscrew the clamp (A) fixing the cable.
o Replace the cable with one of the same length and in accordance
with the specification given above.
o The “green-yellow” earth wire must be connected to the terminal
. It must be about 10 mm longer than the live and
marked
neutral wires.
o The “blue” neutral wire must be connected to the terminal
marked with letter (N) - the live wire must be connected to the
terminal marked with letter (L).
28
My appliance isn’t working correctly
IMPORTANT: If your appliance appears not to be
operating correctly, then you should disconnect it
from your mains supply and then contact
Baumatic Customer Care on telephone number
(0118) 933 6911.
DO NOT ATTEMPT TO REPAIR THE APPLIANCE
YOURSELF.
Please note that if an engineer is asked to attend whilst the product is
under guarantee and finds that the problem is not the result of an
appliance fault, then you may be liable for the cost of the call out
charge.
The appliance must be accessible for the engineer to perform
any necessary repair. If your appliance is installed in such a
way that an engineer is concerned that damage will be caused
to the appliance or your kitchen, then he will not complete a
repair.
This includes situations where appliances have been tiled in,
sealed in with sealant, have wooden obstructions placed in
front of the appliance, like plinths. Or any installation other
than the one specified by Baumatic Ltd. has been completed.
Please refer to the conditions of guarantee that appear on the
warranty card that you receive with the appliance.
29
United Kingdom
Baumatic Ltd.,
Baumatic Buildings,
6 Bennet Road,
Reading, Berkshire
RG2 0QX
United Kingdom
Sales Telephone
(0118) 933 6900
Sales Fax
(0118) 931 0035
Customer Care Telephone
(0118) 933 6911
Customer Care Fax
(0118) 986 9124
Spares Telephone
(01235) 437244
Advice Line Telephone
(0118) 933 6933
E-mail:
sales@baumatic.co.uk
customercare@baumatic.co.uk
spares@baumatic.co.uk
technical@baumatic.co.uk
Website:
www.baumatic.co.uk
Republic of Ireland
01- 6266 798
Czech Republic
Baumatic CR spol s.r.o.
Amperova 495
46215, Librec
Czech Republic
+420 800 185 263
www.baumatic.cz
Slovak Republic
Baumatic Slovakia, s.r.o.
Skultetyho 1
831 04 Bratislava 3
Slovakia
+421 255 640 618
Germany
Baumatic Gmbh
Janderstrasse 9
Mannheim, 68199
Germany
+4962 112 9190
www.baumatic.de
Italy
Baumatic Italia S.R.L.
Via Caltana 129
Campodarsego (Padova), 35011
Italy
+3904 9920 2297
www.baumatic.it
Holland
Baumatic Benelux B.V.
Grindzuigerstraat 22
1333 MS ALMERE
The Netherlands
+3136 549 1555
www.baumatic.nl
30
31
32